* Fwd: Adaptec 71605H HBA randomly failing to detect any drives at init
[not found] <CAKmTNed2uSUGCDkxQSLofjgSGxLpZ154_gNpwt_NWChjR=s8iA@mail.gmail.com>
@ 2014-09-01 16:06 ` Andrew Robertson
2014-09-02 13:28 ` Suresh Thiagarajan
2014-09-02 14:06 ` Emmanuel Florac
0 siblings, 2 replies; 6+ messages in thread
From: Andrew Robertson @ 2014-09-01 16:06 UTC (permalink / raw)
To: linux-scsi
Hi,
I have an Adaptec 71605H HBA that's randomly failing to detect any
drives at boot. I have two systems with this HBA, and both are
showing the exact same behavior. I can reproduce this randomly about
3 out of 4 times, where most of the time it comes up where "lsscsi"
shows no drives attached (other than my boot disk, not attached to
this HBA) - but then occasionally it works fine (~1 out of 4 reboots)
and detects the drives.
On a "good" boot, the kernel messages include:
[ 27.575091] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 27.754640] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
On a "bad" boot, it doesn't include these messages; instead it hangs
for ~60 seconds after "Enter sas_scsi_recover_host busy" and then just
continues to boot (and that seems to never recover). It also never
cleanly shuts down in this state (it hangs forever on "modprobe -q -r
ipmi_devintf" and I have to power-cycle the machine -- I suspect this
is more of a symptom that the kernel is busy doing other things -
possibly still trying to init scsi - isntead an ipmi-specific issue).
I'm happy to test patches/etc on this system if necessary -- and/or if
someone can help point me in the right direction, I'd appreciate it.
Thanks,
Andy
More system info:
---
Linux 3.13.0-35-generic #62-Ubuntu SMP Fri Aug 15 01:58:42 UTC 2014
x86_64 x86_64 x86_64 GNU/Linux
Using: pm80xx 0000:02:00.0: pm80xx: driver version 0.1.37
The Adaptec 71605H HBA has 2 ports, each connected to a different expander.
Bad boot:
[ 5.481062] sas: DONE DISCOVERY on port 0, pid:193, result:0
[ 5.481066] sas: phy2 matched wide port0
[ 5.481071] sas: phy-0:2 added to port-0:0, phy_mask:0x7 (5003048001108c3f)
[ 5.481115] sas: phy-0:4 added to port-0:1, phy_mask:0x10 (50030480010f713f)
[ 5.481118] sas: phy3 matched wide port0
[ 5.481121] sas: phy-0:3 added to port-0:0, phy_mask:0xf (5003048001108c3f)
[ 5.481122] sas: phy5 matched wide port1
[ 5.481124] sas: phy-0:5 added to port-0:1, phy_mask:0x30 (50030480010f713f)
[ 5.481126] sas: phy7 matched wide port1
[ 5.481128] sas: phy-0:7 added to port-0:1, phy_mask:0xb0 (50030480010f713f)
[ 5.481130] sas: phy6 matched wide port1
[ 5.481135] sas: phy-0:6 added to port-0:1, phy_mask:0xf0 (50030480010f713f)
[ 5.481159] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 5.481191] sas: ata7: end_device-0:0:12: dev error handler
[ 5.481220] sas: ata8: end_device-0:0:13: dev error handler
[ 5.481225] sas: ata9: end_device-0:0:14: dev error handler
[ 5.481232] sas: ata10: end_device-0:0:15: dev error handler
[ 5.481259] sas: ata11: end_device-0:0:16: dev error handler
[ 5.481392] sas: ata12: end_device-0:0:17: dev error handler
[ 7.639994] ata8.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.640190] ata7.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.640192] ata7.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.640282] ata11.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.640283] ata11.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.640468] ata10.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.640468] ata10.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.640659] ata12.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.640659] ata12.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.640736] ata7.00: configured for UDMA/133
[ 7.640834] ata11.00: configured for UDMA/133
[ 7.640990] ata10.00: configured for UDMA/133
[ 7.641175] ata12.00: configured for UDMA/133
[ 7.728884] ata8.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.736588] ata8.00: configured for UDMA/133
[ 65.535289] random: init urandom read with 81 bits of entropy available
---
Good Boot:
[ 5.520647] sas: DONE DISCOVERY on port 0, pid:191, result:0
[ 5.520651] sas: phy2 matched wide port0
[ 5.520657] sas: phy-0:2 added to port-0:0, phy_mask:0x7 (5003048001108c3f)
[ 5.520700] sas: phy-0:4 added to port-0:1, phy_mask:0x10 (50030480010f713f)
[ 5.520703] sas: phy3 matched wide port0
[ 5.520705] sas: phy-0:3 added to port-0:0, phy_mask:0xf (5003048001108c3f)
[ 5.520707] sas: phy5 matched wide port1
[ 5.520711] sas: phy-0:5 added to port-0:1, phy_mask:0x30 (50030480010f713f)
[ 5.520713] sas: phy7 matched wide port1
[ 5.520714] sas: phy-0:7 added to port-0:1, phy_mask:0xb0 (50030480010f713f)
[ 5.520715] sas: phy6 matched wide port1
[ 5.520717] sas: phy-0:6 added to port-0:1, phy_mask:0xf0 (50030480010f713f)
[ 5.520739] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 5.520762] sas: ata7: end_device-0:0:12: dev error handler
[ 5.520765] sas: ata8: end_device-0:0:13: dev error handler
[ 5.520784] sas: ata9: end_device-0:0:14: dev error handler
[ 5.520799] sas: ata10: end_device-0:0:15: dev error handler
[ 5.520809] sas: ata11: end_device-0:0:16: dev error handler
[ 5.520941] sas: ata12: end_device-0:0:17: dev error handler
[ 7.679569] ata7.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.679764] ata12.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.679765] ata12.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.679852] ata9.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.679853] ata9.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.680055] ata11.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.680055] ata11.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.680229] ata10.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.680230] ata10.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.680295] ata12.00: configured for UDMA/133
[ 7.680597] ata9.00: configured for UDMA/133
[ 7.680881] ata11.00: configured for UDMA/133
[ 7.680973] ata10.00: configured for UDMA/133
[ 7.768332] ata7.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.776034] ata7.00: configured for UDMA/133
[ 27.575091] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 27.735815] ata8.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 27.742599] ata8.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 27.750259] ata8.00: configured for UDMA/133
[ 27.754640] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 27.763083] scsi 0:0:0:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.771420] scsi 0:0:1:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.779753] scsi 0:0:2:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.788082] scsi 0:0:3:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
Just in case it's useful, here's a dmesg | egrep 'pm80|scsi|ata' from
the good boot
---
[ 0.000000] ACPI: SSDT 00000000dda5db18 000397 (v01 SataRe SataTabl
00001000 INTL 20120711)
[ 0.000000] Memory: 16370400K/16736168K available (7372K kernel
code, 1144K rwdata, 3404K rodata, 1336K init, 1440K bss, 365768K
reserved)
[ 1.353439] libata version 3.00 loaded.
[ 3.942876] Write protecting the kernel read-only data: 12288k
[ 4.068826] pm80xx 0000:02:00.0: pm80xx: driver version 0.1.37
[ 4.082539] scsi1 : ahci
[ 4.082608] scsi2 : ahci
[ 4.082660] scsi3 : ahci
[ 4.082713] scsi4 : ahci
[ 4.082763] scsi5 : ahci
[ 4.082816] scsi6 : ahci
[ 4.082842] ata1: SATA max UDMA/133 abar m2048@0xf7432000 port
0xf7432100 irq 46
[ 4.082844] ata2: SATA max UDMA/133 abar m2048@0xf7432000 port
0xf7432180 irq 46
[ 4.082847] ata3: SATA max UDMA/133 abar m2048@0xf7432000 port
0xf7432200 irq 46
[ 4.082849] ata4: SATA max UDMA/133 abar m2048@0xf7432000 port
0xf7432280 irq 46
[ 4.082852] ata5: SATA max UDMA/133 abar m2048@0xf7432000 port
0xf7432300 irq 46
[ 4.082855] ata6: SATA max UDMA/133 abar m2048@0xf7432000 port
0xf7432380 irq 46
[ 4.401734] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.401756] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.401778] ata6: SATA link down (SStatus 0 SControl 300)
[ 4.401800] ata5: SATA link down (SStatus 0 SControl 300)
[ 4.401823] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.401861] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.402839] ata3.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 4.402840] ata3.00: ATA-9: Samsung SSD 840 PRO Series, DXM06B0Q,
max UDMA/133
[ 4.402841] ata3.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 4.403118] ata3.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 4.403119] ata3.00: configured for UDMA/133
[ 4.409854] scsi 3:0:0:0: Direct-Access ATA Samsung SSD
840 DXM0 PQ: 0 ANSI: 5
[ 4.409966] sd 3:0:0:0: Attached scsi generic sg0 type 0
[ 4.731895] EXT4-fs (sda1): mounted filesystem with ordered data
mode. Opts: (null)
[ 4.952457] scsi0 : pm80xx
[ 4.955564] pm80xx 0000:02:00.0: irq 53 for MSI/MSI-X
[ 4.955577] pm80xx 0000:02:00.0: irq 54 for MSI/MSI-X
[ 4.955585] pm80xx 0000:02:00.0: irq 55 for MSI/MSI-X
[ 4.955588] pm80xx 0000:02:00.0: irq 56 for MSI/MSI-X
[ 4.955592] pm80xx 0000:02:00.0: irq 57 for MSI/MSI-X
[ 4.955597] pm80xx 0000:02:00.0: irq 58 for MSI/MSI-X
[ 4.955601] pm80xx 0000:02:00.0: irq 59 for MSI/MSI-X
[ 4.955606] pm80xx 0000:02:00.0: irq 60 for MSI/MSI-X
[ 4.955611] pm80xx 0000:02:00.0: irq 61 for MSI/MSI-X
[ 4.955616] pm80xx 0000:02:00.0: irq 62 for MSI/MSI-X
[ 4.955619] pm80xx 0000:02:00.0: irq 63 for MSI/MSI-X
[ 4.955625] pm80xx 0000:02:00.0: irq 64 for MSI/MSI-X
[ 4.955629] pm80xx 0000:02:00.0: irq 65 for MSI/MSI-X
[ 4.955634] pm80xx 0000:02:00.0: irq 66 for MSI/MSI-X
[ 4.955637] pm80xx 0000:02:00.0: irq 67 for MSI/MSI-X
[ 4.955640] pm80xx 0000:02:00.0: irq 68 for MSI/MSI-X
[ 4.955646] pm80xx 0000:02:00.0: irq 69 for MSI/MSI-X
[ 4.955649] pm80xx 0000:02:00.0: irq 70 for MSI/MSI-X
[ 4.955653] pm80xx 0000:02:00.0: irq 71 for MSI/MSI-X
[ 4.955658] pm80xx 0000:02:00.0: irq 72 for MSI/MSI-X
[ 4.955661] pm80xx 0000:02:00.0: irq 73 for MSI/MSI-X
[ 4.955665] pm80xx 0000:02:00.0: irq 74 for MSI/MSI-X
[ 4.955670] pm80xx 0000:02:00.0: irq 75 for MSI/MSI-X
[ 4.955673] pm80xx 0000:02:00.0: irq 76 for MSI/MSI-X
[ 4.955679] pm80xx 0000:02:00.0: irq 77 for MSI/MSI-X
[ 4.955682] pm80xx 0000:02:00.0: irq 78 for MSI/MSI-X
[ 4.955686] pm80xx 0000:02:00.0: irq 79 for MSI/MSI-X
[ 4.955689] pm80xx 0000:02:00.0: irq 80 for MSI/MSI-X
[ 4.955694] pm80xx 0000:02:00.0: irq 81 for MSI/MSI-X
[ 4.955699] pm80xx 0000:02:00.0: irq 82 for MSI/MSI-X
[ 4.955704] pm80xx 0000:02:00.0: irq 83 for MSI/MSI-X
[ 4.955707] pm80xx 0000:02:00.0: irq 84 for MSI/MSI-X
[ 4.955711] pm80xx 0000:02:00.0: irq 85 for MSI/MSI-X
[ 4.955714] pm80xx 0000:02:00.0: irq 86 for MSI/MSI-X
[ 4.955717] pm80xx 0000:02:00.0: irq 87 for MSI/MSI-X
[ 4.955722] pm80xx 0000:02:00.0: irq 88 for MSI/MSI-X
[ 4.955725] pm80xx 0000:02:00.0: irq 89 for MSI/MSI-X
[ 4.955729] pm80xx 0000:02:00.0: irq 90 for MSI/MSI-X
[ 4.955732] pm80xx 0000:02:00.0: irq 91 for MSI/MSI-X
[ 4.955737] pm80xx 0000:02:00.0: irq 92 for MSI/MSI-X
[ 4.955741] pm80xx 0000:02:00.0: irq 93 for MSI/MSI-X
[ 4.955746] pm80xx 0000:02:00.0: irq 94 for MSI/MSI-X
[ 4.955749] pm80xx 0000:02:00.0: irq 95 for MSI/MSI-X
[ 4.955752] pm80xx 0000:02:00.0: irq 96 for MSI/MSI-X
[ 4.955757] pm80xx 0000:02:00.0: irq 97 for MSI/MSI-X
[ 4.955761] pm80xx 0000:02:00.0: irq 98 for MSI/MSI-X
[ 4.955764] pm80xx 0000:02:00.0: irq 99 for MSI/MSI-X
[ 4.955767] pm80xx 0000:02:00.0: irq 100 for MSI/MSI-X
[ 4.955773] pm80xx 0000:02:00.0: irq 101 for MSI/MSI-X
[ 4.955776] pm80xx 0000:02:00.0: irq 102 for MSI/MSI-X
[ 4.955779] pm80xx 0000:02:00.0: irq 103 for MSI/MSI-X
[ 4.955783] pm80xx 0000:02:00.0: irq 104 for MSI/MSI-X
[ 4.955788] pm80xx 0000:02:00.0: irq 105 for MSI/MSI-X
[ 4.955792] pm80xx 0000:02:00.0: irq 106 for MSI/MSI-X
[ 4.955795] pm80xx 0000:02:00.0: irq 107 for MSI/MSI-X
[ 4.955799] pm80xx 0000:02:00.0: irq 108 for MSI/MSI-X
[ 4.955804] pm80xx 0000:02:00.0: irq 109 for MSI/MSI-X
[ 4.955807] pm80xx 0000:02:00.0: irq 110 for MSI/MSI-X
[ 4.955810] pm80xx 0000:02:00.0: irq 111 for MSI/MSI-X
[ 4.955816] pm80xx 0000:02:00.0: irq 112 for MSI/MSI-X
[ 4.955819] pm80xx 0000:02:00.0: irq 113 for MSI/MSI-X
[ 4.955822] pm80xx 0000:02:00.0: irq 114 for MSI/MSI-X
[ 4.955826] pm80xx 0000:02:00.0: irq 115 for MSI/MSI-X
[ 4.955831] pm80xx 0000:02:00.0: irq 116 for MSI/MSI-X
[ 5.520739] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 5.520762] sas: ata7: end_device-0:0:12: dev error handler
[ 5.520765] sas: ata8: end_device-0:0:13: dev error handler
[ 5.520784] sas: ata9: end_device-0:0:14: dev error handler
[ 5.520799] sas: ata10: end_device-0:0:15: dev error handler
[ 5.520809] sas: ata11: end_device-0:0:16: dev error handler
[ 5.520941] sas: ata12: end_device-0:0:17: dev error handler
[ 7.679569] ata7.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.679764] ata12.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.679765] ata12.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.679852] ata9.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.679853] ata9.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.680055] ata11.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.680055] ata11.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.680229] ata10.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.680230] ata10.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.680295] ata12.00: configured for UDMA/133
[ 7.680597] ata9.00: configured for UDMA/133
[ 7.680881] ata11.00: configured for UDMA/133
[ 7.680973] ata10.00: configured for UDMA/133
[ 7.768332] ata7.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.776034] ata7.00: configured for UDMA/133
[ 27.575091] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 27.735815] ata8.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 27.742599] ata8.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 27.750259] ata8.00: configured for UDMA/133
[ 27.754640] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 27.763083] scsi 0:0:0:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.771420] scsi 0:0:1:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.779753] scsi 0:0:2:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.788082] scsi 0:0:3:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.796416] scsi 0:0:4:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.804754] scsi 0:0:5:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.813320] scsi 0:0:6:0: Enclosure LSI SAS2X36
0e12 PQ: 0 ANSI: 5
[ 27.886753] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 27.886767] sas: ata7: end_device-0:0:12: dev error handler
[ 27.886781] sas: ata8: end_device-0:0:13: dev error handler
[ 27.886783] sas: ata9: end_device-0:0:14: dev error handler
[ 27.886786] sas: ata10: end_device-0:0:15: dev error handler
[ 27.886787] sas: ata11: end_device-0:0:16: dev error handler
[ 27.886792] sas: ata12: end_device-0:0:17: dev error handler
[ 27.886793] sas: ata13: end_device-0:1:12: dev error handler
[ 27.886795] sas: ata14: end_device-0:1:13: dev error handler
[ 27.886807] sas: ata16: end_device-0:1:15: dev error handler
[ 27.886809] sas: ata15: end_device-0:1:14: dev error handler
[ 27.886810] sas: ata17: end_device-0:1:16: dev error handler
[ 30.045618] ata17.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.045783] ata13.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.045784] ata13.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.045973] ata14.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.045974] ata14.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.046166] ata15.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.046166] ata15.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.046299] ata13.00: configured for UDMA/133
[ 30.046500] ata14.00: configured for UDMA/133
[ 30.046684] ata15.00: configured for UDMA/133
[ 30.107396] ata17.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.115191] ata17.00: configured for UDMA/133
[ 49.889251] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 50.050029] ata16.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 50.056903] ata16.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 50.064697] ata16.00: configured for UDMA/133
[ 50.069160] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 50.073261] scsi 0:0:7:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 50.081602] scsi 0:0:8:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 50.089936] scsi 0:0:9:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 50.098268] scsi 0:0:10:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 50.106687] scsi 0:0:11:0: Direct-Access ATA WDC
WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 50.115423] scsi 0:0:12:0: Enclosure LSI SAS2X28
0e12 PQ: 0 ANSI: 5
[ 50.139025] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 50.139118] sd 0:0:1:0: Attached scsi generic sg2 type 0
[ 50.139215] sd 0:0:2:0: Attached scsi generic sg3 type 0
[ 50.139305] sd 0:0:3:0: Attached scsi generic sg4 type 0
[ 50.139387] sd 0:0:4:0: Attached scsi generic sg5 type 0
[ 50.139483] sd 0:0:5:0: Attached scsi generic sg6 type 0
[ 50.139556] scsi 0:0:6:0: Attached scsi generic sg7 type 13
[ 50.139623] sd 0:0:7:0: Attached scsi generic sg8 type 0
[ 50.139721] sd 0:0:8:0: Attached scsi generic sg9 type 0
[ 50.139806] sd 0:0:9:0: Attached scsi generic sg10 type 0
[ 50.139888] sd 0:0:10:0: Attached scsi generic sg11 type 0
[ 50.139985] sd 0:0:11:0: Attached scsi generic sg12 type 0
[ 50.140049] scsi 0:0:12:0: Attached scsi generic sg13 type 13
[ 51.852181] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 51.852185] sas: ata10: end_device-0:0:15: cmd error handler
[ 51.852197] sas: ata7: end_device-0:0:12: dev error handler
[ 51.852202] sas: ata8: end_device-0:0:13: dev error handler
[ 51.852207] sas: ata9: end_device-0:0:14: dev error handler
[ 51.852208] sas: ata10: end_device-0:0:15: dev error handler
[ 51.852214] sas: ata11: end_device-0:0:16: dev error handler
[ 51.852218] sas: ata12: end_device-0:0:17: dev error handler
[ 51.852219] sas: ata13: end_device-0:1:12: dev error handler
[ 51.852223] sas: ata14: end_device-0:1:13: dev error handler
[ 51.852224] sas: ata15: end_device-0:1:14: dev error handler
[ 51.852227] sas: ata16: end_device-0:1:15: dev error handler
[ 51.852229] sas: ata17: end_device-0:1:16: dev error handler
[ 51.852233] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 51.852711] sas: Enter sas_scsi_recover_host busy: 3 failed: 3
[ 51.852712] sas: ata11: end_device-0:0:16: cmd error handler
[ 51.852714] sas: ata7: end_device-0:0:12: cmd error handler
[ 51.852714] sas: ata8: end_device-0:0:13: cmd error handler
[ 51.852736] sas: ata7: end_device-0:0:12: dev error handler
[ 51.852743] sas: ata8: end_device-0:0:13: dev error handler
[ 51.852745] sas: ata9: end_device-0:0:14: dev error handler
[ 51.852747] sas: ata10: end_device-0:0:15: dev error handler
[ 51.852749] sas: ata11: end_device-0:0:16: dev error handler
[ 51.852752] sas: ata12: end_device-0:0:17: dev error handler
[ 51.852753] sas: ata13: end_device-0:1:12: dev error handler
[ 51.852755] sas: ata14: end_device-0:1:13: dev error handler
[ 51.852756] sas: ata15: end_device-0:1:14: dev error handler
[ 51.852758] sas: ata16: end_device-0:1:15: dev error handler
[ 51.852760] sas: ata17: end_device-0:1:16: dev error handler
[ 51.852764] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 51.853243] sas: Enter sas_scsi_recover_host busy: 4 failed: 4
[ 51.853245] sas: ata9: end_device-0:0:14: cmd error handler
[ 51.853247] sas: ata16: end_device-0:1:15: cmd error handler
[ 51.853248] sas: ata14: end_device-0:1:13: cmd error handler
[ 51.853250] sas: ata17: end_device-0:1:16: cmd error handler
[ 51.853331] sas: ata7: end_device-0:0:12: dev error handler
[ 51.853337] sas: ata8: end_device-0:0:13: dev error handler
[ 51.853339] sas: ata9: end_device-0:0:14: dev error handler
[ 51.853345] sas: ata10: end_device-0:0:15: dev error handler
[ 51.853348] sas: ata11: end_device-0:0:16: dev error handler
[ 51.853353] sas: ata12: end_device-0:0:17: dev error handler
[ 51.853354] sas: ata13: end_device-0:1:12: dev error handler
[ 51.853355] sas: ata14: end_device-0:1:13: dev error handler
[ 51.853356] sas: ata15: end_device-0:1:14: dev error handler
[ 51.853359] sas: ata16: end_device-0:1:15: dev error handler
[ 51.853361] sas: ata17: end_device-0:1:16: dev error handler
[ 51.853368] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 51.868638] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 51.868642] sas: ata15: end_device-0:1:14: cmd error handler
[ 51.868653] sas: ata7: end_device-0:0:12: dev error handler
[ 51.868656] sas: ata8: end_device-0:0:13: dev error handler
[ 51.868658] sas: ata9: end_device-0:0:14: dev error handler
[ 51.868662] sas: ata10: end_device-0:0:15: dev error handler
[ 51.868663] sas: ata11: end_device-0:0:16: dev error handler
[ 51.868664] sas: ata12: end_device-0:0:17: dev error handler
[ 51.868665] sas: ata13: end_device-0:1:12: dev error handler
[ 51.868666] sas: ata14: end_device-0:1:13: dev error handler
[ 51.868667] sas: ata15: end_device-0:1:14: dev error handler
[ 51.868668] sas: ata16: end_device-0:1:15: dev error handler
[ 51.868668] sas: ata17: end_device-0:1:16: dev error handler
[ 51.868677] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 51.889624] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 51.889627] sas: ata13: end_device-0:1:12: cmd error handler
[ 51.889628] sas: ata12: end_device-0:0:17: cmd error handler
[ 51.889644] sas: ata7: end_device-0:0:12: dev error handler
[ 51.889650] sas: ata8: end_device-0:0:13: dev error handler
[ 51.889653] sas: ata9: end_device-0:0:14: dev error handler
[ 51.889655] sas: ata10: end_device-0:0:15: dev error handler
[ 51.889659] sas: ata12: end_device-0:0:17: dev error handler
[ 51.889660] sas: ata11: end_device-0:0:16: dev error handler
[ 51.889662] sas: ata13: end_device-0:1:12: dev error handler
[ 51.889664] sas: ata14: end_device-0:1:13: dev error handler
[ 51.889667] sas: ata15: end_device-0:1:14: dev error handler
[ 51.889670] sas: ata16: end_device-0:1:15: dev error handler
[ 51.889671] sas: ata17: end_device-0:1:16: dev error handler
[ 51.889678] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
---
^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: Adaptec 71605H HBA randomly failing to detect any drives at init
2014-09-01 16:06 ` Fwd: Adaptec 71605H HBA randomly failing to detect any drives at init Andrew Robertson
@ 2014-09-02 13:28 ` Suresh Thiagarajan
2014-09-02 14:06 ` Emmanuel Florac
1 sibling, 0 replies; 6+ messages in thread
From: Suresh Thiagarajan @ 2014-09-02 13:28 UTC (permalink / raw)
To: Andrew Robertson, linux-scsi
On Mon, Sep 1, 2014 at 9:36 PM, Andrew Robertson <andyrobertson101@gmail.com> wrote:
> Hi,
>
> I have an Adaptec 71605H HBA that's randomly failing to detect any
> drives at boot. I have two systems with this HBA, and both are
> showing the exact same behavior. I can reproduce this randomly about
> 3 out of 4 times, where most of the time it comes up where "lsscsi"
> shows no drives attached (other than my boot disk, not attached to
> this HBA) - but then occasionally it works fine (~1 out of 4 reboots)
> and detects the drives.
>
> On a "good" boot, the kernel messages include:
> [ 27.575091] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
> [ 27.754640] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
>
> On a "bad" boot, it doesn't include these messages; instead it hangs
> for ~60 seconds after "Enter sas_scsi_recover_host busy" and then just
> continues to boot (and that seems to never recover). It also never
> cleanly shuts down in this state (it hangs forever on "modprobe -q -r
> ipmi_devintf" and I have to power-cycle the machine -- I suspect this
> is more of a symptom that the kernel is busy doing other things -
> possibly still trying to init scsi - isntead an ipmi-specific issue).
>
> I'm happy to test patches/etc on this system if necessary -- and/or if
> someone can help point me in the right direction, I'd appreciate it.
Hi Andy,
Can you share the following details?
1. Fw version in the card you have. Use below command to get the fw_version sys file.
2. Expander and drive details and how you connected it to HBA?
3. Can you enable full logs and hot plug the expander/devices and share the log if the discovery fails.
Find /sys -iname "fw_version"
Find /sys -iname logging_level
Echo oxfff > "logging_level sys file"
Also can you test with latest Linux stable release?
Thanks,
Suresh
>
> Thanks,
> Andy
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Adaptec 71605H HBA randomly failing to detect any drives at init
2014-09-01 16:06 ` Fwd: Adaptec 71605H HBA randomly failing to detect any drives at init Andrew Robertson
2014-09-02 13:28 ` Suresh Thiagarajan
@ 2014-09-02 14:06 ` Emmanuel Florac
2014-09-05 22:13 ` Andrew Robertson
1 sibling, 1 reply; 6+ messages in thread
From: Emmanuel Florac @ 2014-09-02 14:06 UTC (permalink / raw)
To: Andrew Robertson; +Cc: linux-scsi
Le Mon, 1 Sep 2014 09:06:46 -0700
Andrew Robertson <andyrobertson101@gmail.com> écrivait:
> I'm happy to test patches/etc on this system if necessary -- and/or if
> someone can help point me in the right direction, I'd appreciate it.
In my experience the 7xxx5 are very sensitive to cable length and
backplane type: basically work fine with 50 cm cables, and fails with 80
cm cables with some backplanes (works with Supermicro, not with AIC,
etc).
So what is the backplane and cables you're using?
--
------------------------------------------------------------------------
Emmanuel Florac | Direction technique
| Intellique
| <eflorac@intellique.com>
| +33 1 78 94 84 02
------------------------------------------------------------------------
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Adaptec 71605H HBA randomly failing to detect any drives at init
2014-09-02 14:06 ` Emmanuel Florac
@ 2014-09-05 22:13 ` Andrew Robertson
2014-09-06 5:32 ` Fwd: " Andrew Robertson
2015-05-18 19:19 ` Andrew Robertson
0 siblings, 2 replies; 6+ messages in thread
From: Andrew Robertson @ 2014-09-05 22:13 UTC (permalink / raw)
To: Emmanuel Florac, suresh.thiagarajan; +Cc: linux-scsi
[-- Attachment #1: Type: text/plain, Size: 12069 bytes --]
More info, as requested:
There are 2 sas expander chips in the system (LSI SAS2X28 & SAS2X36),
and there's a connection to each of them from the 71605H via a
separate 0.8m Adaptec cable. (Adaptec 2280200-R). This is a
Supermicro chassis.
Firmware version:
# cat /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/host0/scsi_host/host0/fw_version
02.08.60.01
I don't have immediate physical access to the box, so I'm not able to
do the hotplug logging test. However, I did "reset" the PCI device
via /sys, as shown below, and captured the logs from that (attached,
"dmesg.out.txt").
With the latest kernel, v3.17-rc3, I got a kernel "null pointer
dereference" in the pm80xx module (dmesg output pasted in below).
I will also try replacing the cables with 0.5m adaptec cables as
suggested to see if that helps.
---
Reset test:
# find /sys -iname logging_level
/sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/host0/scsi_host/host0/logging_level
# echo 0xfff > /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/host0/scsi_host/host0/logging_level
# echo 1 > /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/rescan
# echo 1 > /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/reset
# sync
(at which point the process hung; in the dmesg you can see a "sync
blocked for more than 120 seconds")
The disk/expander layout looks like:
[0:0:0:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdb /dev/sg1
[0:0:1:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdc /dev/sg2
[0:0:2:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdd /dev/sg3
[0:0:3:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sde /dev/sg4
[0:0:4:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdf /dev/sg5
[0:0:5:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdg /dev/sg6
[0:0:6:0] enclosu LSI SAS2X36 0e12 - /dev/sg7
[0:0:7:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdh /dev/sg8
[0:0:8:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdi /dev/sg9
[0:0:9:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdj /dev/sg10
[0:0:10:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdk /dev/sg11
[0:0:11:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdl /dev/sg12
[0:0:12:0] enclosu LSI SAS2X28 0e12 - /dev/sg13
dmesg from latest kernel v3.17-rc3 showing (what appears to possibly
be) a kernel bug:
This happened right after I ran "lsscsi" (though can't say if it was
actually caused by that).
[ 309.327805] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000290
[ 309.335829] IP: [<ffffffffc0080d4f>]
pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
[ 309.343258] PGD 0
[ 309.345381] Oops: 0000 [#1] SMP
[ 309.348797] Modules linked in: ipmi_devintf autofs4 arc4 nfsd
auth_rpcgss intel_rapl nfs_acl x86_pkg_temp_thermal nfs
intel_powerclamp coretemp lockd kvm_intel sunrpc kvm fscache
crct10dif_pclmul ttm crc32_pclmul drm_kms_helper rt2800usb
ghash_clmulni_intel rt2x00usb rt2800lib rt2x00lib mac80211 aesni_intel
drm aes_x86_64 lrw gf128mul glue_helper ablk_helper cfg80211 cryptd
crc_ccitt syscopyarea joydev sysfillrect sysimgblt shpchp lpc_ich
ipmi_si ipmi_msghandler mac_hid video ie31200_edac edac_core lp
parport ses enclosure hid_generic usbhid hid raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx xor igb
raid6_pq i2c_algo_bit raid1 e1000e pm80xx dca raid0 libsas ahci ptp
multipath scsi_transport_sas libahci pps_core linear
[ 309.420132] CPU: 5 PID: 1998 Comm: kworker/5:2 Not tainted
3.17.0-031700rc3-generic #201409031132
[ 309.429051] Hardware name: Supermicro X10SLL-F/X10SLL-F, BIOS 2.0 04/24/2014
[ 309.436148] Workqueue: pm80xx pm8001_work_fn [pm80xx]
[ 309.441317] task: ffff880403690000 ti: ffff880404fa4000 task.ti:
ffff880404fa4000
[ 309.448867] RIP: 0010:[<ffffffffc0080d4f>] [<ffffffffc0080d4f>]
pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
[ 309.458765] RSP: 0018:ffff880404fa7cd8 EFLAGS: 00010286
[ 309.464145] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000006e02
[ 309.471342] RDX: 0000000000000000 RSI: 0000000000000286 RDI: ffff880403e98000
[ 309.478546] RBP: ffff880404fa7d18 R08: ffff880404fa4000 R09: 0000000000000000
[ 309.485749] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8804022b8000
[ 309.492954] R13: ffff880403e98000 R14: ffff880401b80180 R15: 0000000000000000
[ 309.500163] FS: 0000000000000000(0000) GS:ffff88041fd40000(0000)
knlGS:0000000000000000
[ 309.508337] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 309.514147] CR2: 0000000000000290 CR3: 0000000001c16000 CR4: 00000000001407e0
[ 309.521348] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 309.528551] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 309.535752] Stack:
[ 309.537837] ffff8804022b8000 ffff880401bbe000 ffff880401b80180
ffff880403e98000
[ 309.545599] ffff8804022b8000 ffff880401bbe000 ffff880401b80180
0000000000000000
[ 309.553349] ffff880404fa7d78 ffffffffc00826e8 ffff880404fa7d78
ffffffff810ababc
[ 309.561091] Call Trace:
[ 309.563611] [<ffffffffc00826e8>]
pm8001_I_T_nexus_event_handler+0xb8/0x1f0 [pm80xx]
[ 309.571449] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
[ 309.577355] [<ffffffffc0084559>] pm8001_work_fn+0x299/0x480 [pm80xx]
[ 309.583869] [<ffffffff8108ce6f>] process_one_work+0x17f/0x490
[ 309.589773] [<ffffffff8108d7eb>] worker_thread+0x11b/0x3f0
[ 309.595413] [<ffffffff8108d6d0>] ? create_worker+0x1e0/0x1e0
[ 309.601225] [<ffffffff81093349>] kthread+0xc9/0xe0
[ 309.606176] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
[ 309.612421] [<ffffffff817a3f3c>] ret_from_fork+0x7c/0xb0
[ 309.617890] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
[ 309.624135] Code: 00 55 48 89 e5 48 83 ec 40 4c 89 6d e8 4c 89 75
f0 49 89 fd 4c 89 7d f8 48 89 5d d8 4c 89 65 e0 48 8b 47 30 48
8b 9f 78 01 00 00 <48> 8b 80 90 02 00 00 4c 8b a0 90 01 00 00 4d 8d 74
24 38 4c 89
[ 309.647551] RIP [<ffffffffc0080d4f>]
pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
[ 309.655100] RSP <ffff880404fa7cd8>
[ 309.658657] CR2: 0000000000000290
[ 309.662045] ---[ end trace 084eaa8941942e9a ]---
[ 309.770413] BUG: unable to handle kernel paging request at ffffffffffffffd8
[ 309.777578] IP: [<ffffffff810936e0>] kthread_data+0x10/0x20
[ 309.783287] PGD 1c19067 PUD 1c1b067 PMD 0
[ 309.787652] Oops: 0000 [#2] SMP
[ 309.791080] Modules linked in: ipmi_devintf autofs4 arc4 nfsd
auth_rpcgss intel_rapl nfs_acl x86_pkg_temp_thermal nfs
intel_powerclamp coretemp lockd kvm_intel sunrpc kvm fscache
crct10dif_pclmul ttm crc32_pclmul drm_kms_helper rt2800usb
ghash_clmulni_intel rt2x00usb rt2800lib rt2x00lib mac80211 aesni_intel
drm aes_x86_64 lrw gf128mul glue_helper ablk_helper cfg80211 cryptd
crc_ccitt syscopyarea joydev sysfillrect sysimgblt shpchp lpc_ich
ipmi_si ipmi_msghandler mac_hid video ie31200_edac edac_core lp
parport ses enclosure hid_generic usbhid hid raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx xor igb
raid6_pq i2c_algo_bit raid1 e1000e pm80xx dca raid0 libsas ahci ptp
multipath scsi_transport_sas libahci pps_core linear
[ 309.862627] CPU: 5 PID: 1998 Comm: kworker/5:2 Tainted: G D
3.17.0-031700rc3-generic #201409031132
[ 309.872709] Hardware name: Supermicro X10SLL-F/X10SLL-F, BIOS 2.0 04/24/2014
[ 309.879834] task: ffff880403690000 ti: ffff880404fa4000 task.ti:
ffff880404fa4000
[ 309.887407] RIP: 0010:[<ffffffff810936e0>] [<ffffffff810936e0>]
kthread_data+0x10/0x20
[ 309.895562] RSP: 0018:ffff880404fa78e8 EFLAGS: 00010092
[ 309.900939] RAX: 0000000000000000 RBX: 0000000000000005 RCX: ffffffff81ec2e80
[ 309.908139] RDX: 0000000000000000 RSI: 0000000000000005 RDI: ffff880403690000
[ 309.915343] RBP: ffff880404fa78e8 R08: 0000000000000000 R09: 0000000000000246
[ 309.922549] R10: 000000000000001a R11: 0000000000000013 R12: 0000000000000005
[ 309.929749] R13: ffff880403690538 R14: 0000000000000001 R15: 0000000000000046
[ 309.936953] FS: 0000000000000000(0000) GS:ffff88041fd40000(0000)
knlGS:0000000000000000
[ 309.945130] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 309.950942] CR2: 0000000000000028 CR3: 0000000001c16000 CR4: 00000000001407e0
[ 309.958140] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 309.965345] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 309.972548] Stack:
[ 309.974632] ffff880404fa7908 ffffffff8108e725 ffff880404fa7908
ffff88041fd545c0
[ 309.982368] ffff880404fa7988 ffffffff8179f8b3 ffff880404fa7948
ffff880403690000
[ 309.990110] ffff880404fa7fd8 00000000000145c0 ffff880404fa7948
00000000000145c0
[ 309.997858] Call Trace:
[ 310.000377] [<ffffffff8108e725>] wq_worker_sleeping+0x15/0xb0
[ 310.006281] [<ffffffff8179f8b3>] __schedule+0x5e3/0x770
[ 310.011666] [<ffffffff8179fb19>] schedule+0x29/0x70
[ 310.016704] [<ffffffff81077795>] do_exit+0x2a5/0x470
[ 310.021830] [<ffffffff810c9fbc>] ? kmsg_dump+0x9c/0xc0
[ 310.027128] [<ffffffff81018d08>] oops_end+0xb8/0x160
[ 310.032253] [<ffffffff81788489>] no_context+0x1be/0x1cd
[ 310.037631] [<ffffffff8178866b>] __bad_area_nosemaphore+0x1d3/0x1f2
[ 310.044059] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
[ 310.049962] [<ffffffff8178869d>] bad_area_nosemaphore+0x13/0x15
[ 310.056043] [<ffffffff81062312>] __do_page_fault+0x3b2/0x550
[ 310.061856] [<ffffffff810ae3aa>] ? idle_balance+0x7a/0x2c0
[ 310.067493] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
[ 310.073399] [<ffffffff810135c6>] ? __switch_to+0xf6/0x5b0
[ 310.078960] [<ffffffff8106263e>] do_page_fault+0x3e/0x80
[ 310.084431] [<ffffffff817a6088>] page_fault+0x28/0x30
[ 310.089643] [<ffffffffc0080d4f>] ?
pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
[ 310.096957] [<ffffffffc00826e8>]
pm8001_I_T_nexus_event_handler+0xb8/0x1f0 [pm80xx]
[ 310.104791] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
[ 310.110691] [<ffffffffc0084559>] pm8001_work_fn+0x299/0x480 [pm80xx]
[ 310.117205] [<ffffffff8108ce6f>] process_one_work+0x17f/0x490
[ 310.123106] [<ffffffff8108d7eb>] worker_thread+0x11b/0x3f0
[ 310.128752] [<ffffffff8108d6d0>] ? create_worker+0x1e0/0x1e0
[ 310.134572] [<ffffffff81093349>] kthread+0xc9/0xe0
[ 310.139519] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
[ 310.145763] [<ffffffff817a3f3c>] ret_from_fork+0x7c/0xb0
[ 310.151227] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
[ 310.157473] Code: 00 48 89 e5 5d 48 8b 40 c8 48 c1 e8 02 83 e0 01
c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8b 87 c8 04 00 00
55 48 89 e5 <48> 8b 40 d8 5d c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44
00 00
[ 310.180886] RIP [<ffffffff810936e0>] kthread_data+0x10/0x20
[ 310.186679] RSP <ffff880404fa78e8>
[ 310.190239] CR2: ffffffffffffffd8
[ 310.193623] ---[ end trace 084eaa8941942e9b ]---
[ 310.306147] Fixing recursive fault but reboot is needed!
On Wed, Sep 3, 2014 at 12:06 AM, Emmanuel Florac <eflorac@intellique.com> wrote:
> Le Mon, 1 Sep 2014 09:06:46 -0700
> Andrew Robertson <andyrobertson101@gmail.com> écrivait:
>
>> I'm happy to test patches/etc on this system if necessary -- and/or if
>> someone can help point me in the right direction, I'd appreciate it.
>
> In my experience the 7xxx5 are very sensitive to cable length and
> backplane type: basically work fine with 50 cm cables, and fails with 80
> cm cables with some backplanes (works with Supermicro, not with AIC,
> etc).
>
> So what is the backplane and cables you're using?
>
> --
> ------------------------------------------------------------------------
> Emmanuel Florac | Direction technique
> | Intellique
> | <eflorac@intellique.com>
> | +33 1 78 94 84 02
> ------------------------------------------------------------------------
[-- Attachment #2: dmesg.out.txt --]
[-- Type: text/plain, Size: 211132 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.13.0-35-generic (buildd@panlong) (gcc version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #62-Ubuntu SMP Fri Aug 15 01:58:42 UTC 2014 (Ubuntu 3.13.0-35.62-generic 3.13.11.6)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-35-generic root=UUID=2ce6dd7a-f48d-4e04-86ce-1defa10caef2 ro console=tty1 console=ttyS1,115200n8 nomodeset text nomdmonddf nomdmonisw
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000008fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cd820fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cd821000-0x00000000cd827fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000cd828000-0x00000000dd818fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dd819000-0x00000000dd8fcfff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000dd8fd000-0x00000000dd945fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dd946000-0x00000000dda7afff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000dda7b000-0x00000000df7fefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000df7ff000-0x00000000df7fffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041fffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: Supermicro X10SLL-F/X10SLL-F, BIOS 2.0 04/24/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x420000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CBFFF write-protect
[ 0.000000] CC000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7C00000000 write-back
[ 0.000000] 1 base 0400000000 mask 7FE0000000 write-back
[ 0.000000] 2 base 00E0000000 mask 7FE0000000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] original variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 16GB, type WB
[ 0.000000] reg 1, base: 16GB, range: 512MB, type WB
[ 0.000000] reg 2, base: 3584MB, range: 512MB, type UC
[ 0.000000] total RAM covered: 16384M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 64K num_reg: 6 lose cover RAM: 0G
[ 0.000000] New variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 2GB, type WB
[ 0.000000] reg 1, base: 2GB, range: 1GB, type WB
[ 0.000000] reg 2, base: 3GB, range: 512MB, type WB
[ 0.000000] reg 3, base: 4GB, range: 4GB, type WB
[ 0.000000] reg 4, base: 8GB, range: 8GB, type WB
[ 0.000000] reg 5, base: 16GB, range: 512MB, type WB
[ 0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdf800 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd720-0x000fd72f] mapped at [ffff8800000fd720]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000089000] 89000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01fdf000, 0x01fdffff] PGTABLE
[ 0.000000] BRK [0x01fe0000, 0x01fe0fff] PGTABLE
[ 0.000000] BRK [0x01fe1000, 0x01fe1fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x41fe00000-0x41fffffff]
[ 0.000000] [mem 0x41fe00000-0x41fffffff] page 2M
[ 0.000000] BRK [0x01fe2000, 0x01fe2fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x41c000000-0x41fdfffff]
[ 0.000000] [mem 0x41c000000-0x41fdfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x400000000-0x41bffffff]
[ 0.000000] [mem 0x400000000-0x41bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xcd820fff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0xbfffffff] page 1G
[ 0.000000] [mem 0xc0000000-0xcd7fffff] page 2M
[ 0.000000] [mem 0xcd800000-0xcd820fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0xcd828000-0xdd818fff]
[ 0.000000] [mem 0xcd828000-0xcd9fffff] page 4k
[ 0.000000] [mem 0xcda00000-0xdd7fffff] page 2M
[ 0.000000] [mem 0xdd800000-0xdd818fff] page 4k
[ 0.000000] BRK [0x01fe3000, 0x01fe3fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0xdd8fd000-0xdd945fff]
[ 0.000000] [mem 0xdd8fd000-0xdd945fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0xdf7ff000-0xdf7fffff]
[ 0.000000] [mem 0xdf7ff000-0xdf7fffff] page 4k
[ 0.000000] BRK [0x01fe4000, 0x01fe4fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x3ffffffff]
[ 0.000000] [mem 0x100000000-0x3ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x358de000-0x36c66fff]
[ 0.000000] ACPI: RSDP 00000000000f0490 000024 (v02 SUPERM)
[ 0.000000] ACPI: XSDT 00000000dda4e098 0000B4 (v01 SUPERM SMCI--MB 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 00000000dda5b5c8 00010C (v05 SUPERM SMCI--MB 01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 00000000dda4e1e8 00D3DB (v02 SUPERM SMCI--MB 00000000 INTL 20120711)
[ 0.000000] ACPI: FACS 00000000dda7af80 000040
[ 0.000000] ACPI: APIC 00000000dda5b6d8 000092 (v03 SUPERM SMCI--MB 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 00000000dda5b770 000044 (v01 SUPERM SMCI--MB 01072009 AMI 00010013)
[ 0.000000] ACPI: SSDT 00000000dda5b7b8 000BEE (v01 Ther_R Ther_Rvp 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 00000000dda5c3a8 000540 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 00000000dda5c8e8 000B74 (v01 CpuRef CpuSsdt 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 00000000dda5d460 0002F2 (v01 PmRef Cpu0Tst 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 00000000dda5d758 000348 (v01 PmRef ApTst 00003000 INTL 20051117)
[ 0.000000] ACPI: MCFG 00000000dda5daa0 00003C (v01 SUPERM SMCI--MB 01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 00000000dda5dae0 000038 (v01 SUPERM SMCI--MB 01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 00000000dda5db18 000397 (v01 SataRe SataTabl 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 00000000dda5deb0 005B5E (v01 SaSsdt SaSsdt 00003000 INTL 20120711)
[ 0.000000] ACPI: SPMI 00000000dda63a10 000040 (v05 A M I OEMSPMI 00000000 AMI. 00000000)
[ 0.000000] ACPI: DMAR 00000000dda63a50 000080 (v01 INTEL BDW 00000001 INTL 00000001)
[ 0.000000] ACPI: EINJ 00000000dda63ad0 000130 (v01 AMI AMI EINJ 00000000 00000000)
[ 0.000000] ACPI: ERST 00000000dda63c00 000230 (v01 AMIER AMI ERST 00000000 00000000)
[ 0.000000] ACPI: HEST 00000000dda63e30 0000A8 (v01 AMI AMI HEST 00000000 00000000)
[ 0.000000] ACPI: BERT 00000000dda63ed8 000030 (v01 AMI AMI BERT 00000000 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000041fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x41fffffff]
[ 0.000000] NODE_DATA [mem 0x41fff9000-0x41fffdfff]
[ 0.000000] [ffffea0000000000-ffffea00107fffff] PMD -> [ffff88040f600000-ffff88041f5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x41fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0008efff]
[ 0.000000] node 0: [mem 0x00100000-0xcd820fff]
[ 0.000000] node 0: [mem 0xcd828000-0xdd818fff]
[ 0.000000] node 0: [mem 0xdd8fd000-0xdd945fff]
[ 0.000000] node 0: [mem 0xdf7ff000-0xdf7fffff]
[ 0.000000] node 0: [mem 0x100000000-0x41fffffff]
[ 0.000000] On node 0 totalpages: 4184042
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3982 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14114 pages used for memmap
[ 0.000000] DMA32 zone: 903260 pages, LIFO batch:31
[ 0.000000] Normal zone: 51200 pages used for memmap
[ 0.000000] Normal zone: 3276800 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00090000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcd821000-0xcd827fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdd819000-0xdd8fcfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdd946000-0xdda7afff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdda7b000-0xdf7fefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf800000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xdf800000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88041fc00000 s86336 r8192 d24256 u262144
[ 0.000000] pcpu-alloc: s86336 r8192 d24256 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 4118643
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-35-generic root=UUID=2ce6dd7a-f48d-4e04-86ce-1defa10caef2 ro console=tty1 console=ttyS1,115200n8 nomodeset text nomdmonddf nomdmonisw
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 16370396K/16736168K available (7372K kernel code, 1144K rwdata, 3404K rodata, 1336K init, 1440K bss, 365772K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
[ 0.000000] Offload RCU callbacks from all CPUs
[ 0.000000] Offload RCU callbacks from CPUs: 0-7.
[ 0.000000] NR_IRQS:16640 nr_irqs:744 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty1] enabled
[ 0.000000] console [ttyS1] enabled
[ 0.000000] allocated 67108864 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.004000] tsc: Detected 3300.108 MHz processor
[ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 6600.21 BogoMIPS (lpj=13200432)
[ 0.010880] pid_max: default: 32768 minimum: 301
[ 0.015588] Security Framework initialized
[ 0.019783] AppArmor: AppArmor initialized
[ 0.023964] Yama: becoming mindful.
[ 0.028240] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.037881] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.046124] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.053101] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.060676] Initializing cgroup subsys memory
[ 0.065121] Initializing cgroup subsys devices
[ 0.069645] Initializing cgroup subsys freezer
[ 0.074166] Initializing cgroup subsys blkio
[ 0.078519] Initializing cgroup subsys perf_event
[ 0.083303] Initializing cgroup subsys hugetlb
[ 0.087839] CPU: Physical Processor ID: 0
[ 0.091930] CPU: Processor Core ID: 0
[ 0.096939] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.096939] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.110814] mce: CPU supports 9 MCE banks
[ 0.114921] CPU0: Thermal monitoring enabled (TM1)
[ 0.119803] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.119803] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0
[ 0.119803] tlb_flushall_shift: 6
[ 0.133988] Freeing SMP alternatives memory: 32K (ffffffff81e6d000 - ffffffff81e75000)
[ 0.142703] ACPI: Core revision 20131115
[ 0.154168] ACPI: All ACPI Tables successfully acquired
[ 0.160013] ftrace: allocating 28537 entries in 112 pages
[ 0.174141] dmar: Host address width 39
[ 0.178066] dmar: DRHD base: 0x000000fed90000 flags: 0x1
[ 0.183466] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap d2008c20660462 ecap f010da
[ 0.191658] dmar: RMRR base: 0x000000df697000 end: 0x000000df6a5fff
[ 0.198065] IOAPIC id 8 under DRHD base 0xfed90000 IOMMU 0
[ 0.203700] HPET id 0 under DRHD base 0xfed90000
[ 0.208381] Your BIOS is broken and requested that x2apic be disabled.
[ 0.208381] This will slightly decrease performance.
[ 0.208381] Use 'intremap=no_x2apic_optout' to override BIOS request.
[ 0.226432] Enabled IRQ remapping in xapic mode
[ 0.231033] x2apic not enabled, IRQ remapping is in xapic mode
[ 0.237352] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.283069] smpboot: CPU0: Intel(R) Xeon(R) CPU E3-1230 v3 @ 3.30GHz (fam: 06, model: 3c, stepping: 03)
[ 0.292741] TSC deadline timer enabled
[ 0.292747] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.303253] ... version: 3
[ 0.307330] ... bit width: 48
[ 0.311492] ... generic registers: 4
[ 0.315569] ... value mask: 0000ffffffffffff
[ 0.320949] ... max period: 0000ffffffffffff
[ 0.326326] ... fixed-purpose events: 3
[ 0.330401] ... event mask: 000000070000000f
[ 0.336820] x86: Booting SMP configuration:
[ 0.358879] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.341077] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7
[ 0.452691] x86: Booted up 1 node, 8 CPUs
[ 0.457032] smpboot: Total of 8 processors activated (52801.72 BogoMIPS)
[ 0.470759] devtmpfs: initialized
[ 0.475927] EVM: security.selinux
[ 0.479315] EVM: security.SMACK64
[ 0.482701] EVM: security.ima
[ 0.485739] EVM: security.capability
[ 0.489415] PM: Registering ACPI NVS region [mem 0xcd821000-0xcd827fff] (28672 bytes)
[ 0.497337] PM: Registering ACPI NVS region [mem 0xdd946000-0xdda7afff] (1265664 bytes)
[ 0.505910] pinctrl core: initialized pinctrl subsystem
[ 0.511245] regulator-dummy: no parameters
[ 0.515447] RTC time: 21:48:22, date: 09/05/14
[ 0.519979] NET: Registered protocol family 16
[ 0.524565] cpuidle: using governor ladder
[ 0.528733] cpuidle: using governor menu
[ 0.532751] ACPI: bus type PCI registered
[ 0.536837] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.543383] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.552778] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.563569] PCI: Using configuration type 1 for base access
[ 0.569841] bio: create slab <bio-0> at 0
[ 0.574025] ACPI: Added _OSI(Module Device)
[ 0.578283] ACPI: Added _OSI(Processor Device)
[ 0.582793] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.587560] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.595776] ACPI: Executed 5 blocks of module-level executable AML code
[ 0.664542] ACPI: SSDT 00000000dd8abc18 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.673427] ACPI: Dynamic OEM Table Load:
[ 0.677636] ACPI: SSDT (null) 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.688604] ACPI: SSDT 00000000dd8ab618 0005AA (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.697545] ACPI: Dynamic OEM Table Load:
[ 0.701755] ACPI: SSDT (null) 0005AA (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.712496] ACPI: SSDT 00000000dd8aad98 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.721386] ACPI: Dynamic OEM Table Load:
[ 0.725594] ACPI: SSDT (null) 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.737208] ACPI: Interpreter enabled
[ 0.740951] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131115/hwxface-580)
[ 0.750397] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
[ 0.759828] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20131115/hwxface-580)
[ 0.769260] ACPI: (supports S0 S4 S5)
[ 0.773000] ACPI: Using IOAPIC for interrupt routing
[ 0.778060] HEST: Table parsing has been initialized.
[ 0.783184] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.792507] ACPI: No dock devices found.
[ 0.796753] ACPI: Power Resource [PG00] (on)
[ 0.808572] ACPI: Power Resource [PG01] (on)
[ 0.820556] ACPI: Power Resource [PG02] (on)
[ 0.832901] ACPI: Power Resource [FN00] (off)
[ 0.837371] ACPI: Power Resource [FN01] (off)
[ 0.841842] ACPI: Power Resource [FN02] (off)
[ 0.846316] ACPI: Power Resource [FN03] (off)
[ 0.850779] ACPI: Power Resource [FN04] (off)
[ 0.855740] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.862000] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.870568] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.879157] PCI host bridge to bus 0000:00
[ 0.883324] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.888879] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.895130] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.901373] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.908317] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff]
[ 0.915258] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[ 0.922194] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 0.929129] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 0.936068] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 1.128897] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[ 1.135838] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[ 1.142775] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfeafffff]
[ 1.149714] pci 0000:00:00.0: [8086:0c08] type 00 class 0x060000
[ 1.149774] pci 0000:00:01.0: [8086:0c01] type 01 class 0x060400
[ 1.149797] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 1.149831] pci 0000:00:01.0: System wakeup disabled by ACPI
[ 1.155576] pci 0000:00:01.1: [8086:0c05] type 01 class 0x060400
[ 1.155599] pci 0000:00:01.1: PME# supported from D0 D3hot D3cold
[ 1.155629] pci 0000:00:01.1: System wakeup disabled by ACPI
[ 1.161403] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
[ 1.161420] pci 0000:00:14.0: reg 0x10: [mem 0xf7420000-0xf742ffff 64bit]
[ 1.161471] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 1.161509] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 1.167264] pci 0000:00:19.0: [8086:153a] type 00 class 0x020000
[ 1.167279] pci 0000:00:19.0: reg 0x10: [mem 0xf7400000-0xf741ffff]
[ 1.167286] pci 0000:00:19.0: reg 0x14: [mem 0xf7435000-0xf7435fff]
[ 1.167293] pci 0000:00:19.0: reg 0x18: [io 0xf020-0xf03f]
[ 1.167343] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 1.167381] pci 0000:00:19.0: System wakeup disabled by ACPI
[ 1.173131] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320
[ 1.173149] pci 0000:00:1a.0: reg 0x10: [mem 0xf7434000-0xf74343ff]
[ 1.173225] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 1.173266] pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 1.179013] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400
[ 1.179067] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.179096] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 1.184838] pci 0000:00:1c.1: [8086:8c12] type 01 class 0x060400
[ 1.184891] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 1.184920] pci 0000:00:1c.1: System wakeup disabled by ACPI
[ 1.190686] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320
[ 1.190703] pci 0000:00:1d.0: reg 0x10: [mem 0xf7433000-0xf74333ff]
[ 1.190780] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 1.190821] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 1.196570] pci 0000:00:1f.0: [8086:8c52] type 00 class 0x060100
[ 1.196705] pci 0000:00:1f.2: [8086:8c02] type 00 class 0x010601
[ 1.196717] pci 0000:00:1f.2: reg 0x10: [io 0xf070-0xf077]
[ 1.196724] pci 0000:00:1f.2: reg 0x14: [io 0xf060-0xf063]
[ 1.196730] pci 0000:00:1f.2: reg 0x18: [io 0xf050-0xf057]
[ 1.196737] pci 0000:00:1f.2: reg 0x1c: [io 0xf040-0xf043]
[ 1.196743] pci 0000:00:1f.2: reg 0x20: [io 0xf000-0xf01f]
[ 1.196749] pci 0000:00:1f.2: reg 0x24: [mem 0xf7432000-0xf74327ff]
[ 1.196780] pci 0000:00:1f.2: PME# supported from D3hot
[ 1.196827] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
[ 1.196839] pci 0000:00:1f.3: reg 0x10: [mem 0xf7431000-0xf74310ff 64bit]
[ 1.196856] pci 0000:00:1f.3: reg 0x20: [io 0x0580-0x059f]
[ 1.196915] pci 0000:00:1f.6: [8086:8c24] type 00 class 0x118000
[ 1.196931] pci 0000:00:1f.6: reg 0x10: [mem 0xf7430000-0xf7430fff 64bit]
[ 1.197045] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.202111] pci 0000:02:00.0: [9005:8088] type 00 class 0x010700
[ 1.202120] pci 0000:02:00.0: reg 0x10: [mem 0xf7250000-0xf725ffff 64bit]
[ 1.202126] pci 0000:02:00.0: reg 0x18: [mem 0xf7240000-0xf724ffff 64bit]
[ 1.202134] pci 0000:02:00.0: reg 0x24: [mem 0xf7200000-0xf723ffff]
[ 1.202139] pci 0000:02:00.0: reg 0x30: [mem 0xf7100000-0xf71fffff pref]
[ 1.202163] pci 0000:02:00.0: supports D1
[ 1.202164] pci 0000:02:00.0: PME# supported from D0 D1 D3hot
[ 1.202176] pci 0000:02:00.0: System wakeup disabled by ACPI
[ 1.215930] pci 0000:00:01.1: PCI bridge to [bus 02]
[ 1.220967] pci 0000:00:01.1: bridge window [mem 0xf7100000-0xf72fffff]
[ 1.221049] pci 0000:03:00.0: [1a03:1150] type 01 class 0x060400
[ 1.221155] pci 0000:03:00.0: supports D1 D2
[ 1.221156] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.221180] pci 0000:03:00.0: System wakeup disabled by ACPI
[ 1.226923] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 1.237012] pci 0000:00:1c.0: PCI bridge to [bus 03-04]
[ 1.242300] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 1.242303] pci 0000:00:1c.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 1.242385] pci 0000:04:00.0: [1a03:2000] type 00 class 0x030000
[ 1.242411] pci 0000:04:00.0: reg 0x10: [mem 0xf6000000-0xf6ffffff]
[ 1.242424] pci 0000:04:00.0: reg 0x14: [mem 0xf7000000-0xf701ffff]
[ 1.242437] pci 0000:04:00.0: reg 0x18: [io 0xe000-0xe07f]
[ 1.242534] pci 0000:04:00.0: supports D1 D2
[ 1.242535] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.242618] pci 0000:03:00.0: PCI bridge to [bus 04]
[ 1.247658] pci 0000:03:00.0: bridge window [io 0xe000-0xefff]
[ 1.247663] pci 0000:03:00.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 1.247768] pci 0000:05:00.0: [8086:1533] type 00 class 0x020000
[ 1.247790] pci 0000:05:00.0: reg 0x10: [mem 0xf7300000-0xf737ffff]
[ 1.247822] pci 0000:05:00.0: reg 0x18: [io 0xd000-0xd01f]
[ 1.247838] pci 0000:05:00.0: reg 0x1c: [mem 0xf7380000-0xf7383fff]
[ 1.247975] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[ 1.248015] pci 0000:05:00.0: System wakeup disabled by ACPI
[ 1.261787] pci 0000:00:1c.1: PCI bridge to [bus 05]
[ 1.266823] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff]
[ 1.266826] pci 0000:00:1c.1: bridge window [mem 0xf7300000-0xf73fffff]
[ 1.267409] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 10 *11 12 14 15)
[ 1.274884] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 *10 11 12 14 15)
[ 1.282361] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 10 *11 12 14 15)
[ 1.289824] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 10 *11 12 14 15)
[ 1.297278] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 *10 11 12 14 15)
[ 1.304728] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 10 11 12 14 15) *0, disabled.
[ 1.313488] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 10 11 12 14 15) *0, disabled.
[ 1.322232] ACPI: PCI Interrupt Link [LNKH] (IRQs *5)
[ 1.327813] ACPI: Enabled 7 GPEs in block 00 to 3F
[ 1.332799] ACPI: \_SB_.PCI0: notify handler is installed
[ 1.332839] Found 1 acpi root devices
[ 1.332903] vgaarb: device added: PCI:0000:04:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.341072] vgaarb: loaded
[ 1.343846] vgaarb: bridge control possible 0000:04:00.0
[ 1.349309] SCSI subsystem initialized
[ 1.353147] libata version 3.00 loaded.
[ 1.353158] ACPI: bus type USB registered
[ 1.357243] usbcore: registered new interface driver usbfs
[ 1.362803] usbcore: registered new interface driver hub
[ 1.368204] usbcore: registered new device driver usb
[ 1.373389] PCI: Using ACPI for IRQ routing
[ 1.378786] PCI: pci_cache_line_size set to 64 bytes
[ 1.378847] e820: reserve RAM buffer [mem 0x0008fc00-0x0008ffff]
[ 1.378848] e820: reserve RAM buffer [mem 0xcd821000-0xcfffffff]
[ 1.378849] e820: reserve RAM buffer [mem 0xdd819000-0xdfffffff]
[ 1.378850] e820: reserve RAM buffer [mem 0xdd946000-0xdfffffff]
[ 1.378851] e820: reserve RAM buffer [mem 0xdf800000-0xdfffffff]
[ 1.378896] NetLabel: Initializing
[ 1.382368] NetLabel: domain hash size = 128
[ 1.386788] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.391827] NetLabel: unlabeled traffic allowed by default
[ 1.397515] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 1.404355] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 1.412277] Switched to clocksource hpet
[ 1.418973] AppArmor: AppArmor Filesystem Enabled
[ 1.423764] pnp: PnP ACPI init
[ 1.426898] ACPI: bus type PNP registered
[ 1.431039] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 1.437723] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 1.437729] pnp 00:01: [dma 4]
[ 1.437737] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 1.437747] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 1.437830] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.437856] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 1.437882] system 00:05: [io 0x0800-0x087f] has been reserved
[ 1.443878] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.443900] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.443919] system 00:07: [io 0x1854-0x1857] has been reserved
[ 1.449914] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 1.449959] system 00:08: [io 0x0a00-0x0a1f] has been reserved
[ 1.455948] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.456090] pnp 00:09: [dma 0 disabled]
[ 1.456116] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.456255] pnp 00:0a: [dma 0 disabled]
[ 1.456280] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.456309] system 00:0b: [io 0x04d0-0x04d1] has been reserved
[ 1.462303] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.462360] pnp 00:0c: Plug and Play ACPI device, IDs IPI0001 (active)
[ 1.462575] system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 1.469260] system 00:0d: [mem 0xfed10000-0xfed17fff] has been reserved
[ 1.475942] system 00:0d: [mem 0xfed18000-0xfed18fff] has been reserved
[ 1.491617] system 00:0d: [mem 0xfed19000-0xfed19fff] has been reserved
[ 1.498296] system 00:0d: [mem 0xf8000000-0xfbffffff] has been reserved
[ 1.504980] system 00:0d: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 1.511666] system 00:0d: [mem 0xfed90000-0xfed93fff] could not be reserved
[ 1.518697] system 00:0d: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 1.525381] system 00:0d: [mem 0xff000000-0xffffffff] has been reserved
[ 1.532064] system 00:0d: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 1.539099] system 00:0d: [mem 0xf7fe0000-0xf7feffff] has been reserved
[ 1.545779] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.545914] pnp: PnP ACPI: found 14 devices
[ 1.550176] ACPI: bus type PNP unregistered
[ 1.560342] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.565381] pci 0000:00:01.1: PCI bridge to [bus 02]
[ 1.570416] pci 0000:00:01.1: bridge window [mem 0xf7100000-0xf72fffff]
[ 1.577274] pci 0000:03:00.0: PCI bridge to [bus 04]
[ 1.582309] pci 0000:03:00.0: bridge window [io 0xe000-0xefff]
[ 1.588476] pci 0000:03:00.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 1.595340] pci 0000:00:1c.0: PCI bridge to [bus 03-04]
[ 1.600634] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 1.606800] pci 0000:00:1c.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 1.613655] pci 0000:00:1c.1: PCI bridge to [bus 05]
[ 1.618685] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff]
[ 1.624851] pci 0000:00:1c.1: bridge window [mem 0xf7300000-0xf73fffff]
[ 1.631711] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.631713] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.631714] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.631714] pci_bus 0000:00: resource 7 [mem 0x000cc000-0x000cffff]
[ 1.631715] pci_bus 0000:00: resource 8 [mem 0x000d0000-0x000d3fff]
[ 1.631716] pci_bus 0000:00: resource 9 [mem 0x000d4000-0x000d7fff]
[ 1.631717] pci_bus 0000:00: resource 10 [mem 0x000d8000-0x000dbfff]
[ 1.631718] pci_bus 0000:00: resource 11 [mem 0x000dc000-0x000dffff]
[ 1.631719] pci_bus 0000:00: resource 12 [mem 0x000e0000-0x000e3fff]
[ 1.631720] pci_bus 0000:00: resource 13 [mem 0x000e4000-0x000e7fff]
[ 1.631721] pci_bus 0000:00: resource 14 [mem 0xe0000000-0xfeafffff]
[ 1.631722] pci_bus 0000:02: resource 1 [mem 0xf7100000-0xf72fffff]
[ 1.631723] pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
[ 1.631724] pci_bus 0000:03: resource 1 [mem 0xf6000000-0xf70fffff]
[ 1.631725] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 1.631726] pci_bus 0000:04: resource 1 [mem 0xf6000000-0xf70fffff]
[ 1.631727] pci_bus 0000:05: resource 0 [io 0xd000-0xdfff]
[ 1.631728] pci_bus 0000:05: resource 1 [mem 0xf7300000-0xf73fffff]
[ 1.631744] NET: Registered protocol family 2
[ 1.636290] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.643918] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.650788] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.657494] TCP: reno registered
[ 1.660818] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.667019] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.673686] NET: Registered protocol family 1
[ 1.716072] pci 0000:04:00.0: Boot video device
[ 1.716087] PCI: CLS 64 bytes, default 64
[ 1.716123] Trying to unpack rootfs image as initramfs...
[ 1.935470] Freeing initrd memory: 20004K (ffff8800358de000 - ffff880036c67000)
[ 1.942901] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.949418] software IO TLB [mem 0xd9819000-0xdd819000] (64MB) mapped at [ffff8800d9819000-ffff8800dd818fff]
[ 1.959545] microcode: CPU0 sig=0x306c3, pf=0x2, revision=0x17
[ 1.965456] microcode: CPU1 sig=0x306c3, pf=0x2, revision=0x17
[ 1.971361] microcode: CPU2 sig=0x306c3, pf=0x2, revision=0x17
[ 1.977285] microcode: CPU3 sig=0x306c3, pf=0x2, revision=0x17
[ 1.983185] microcode: CPU4 sig=0x306c3, pf=0x2, revision=0x17
[ 1.989086] microcode: CPU5 sig=0x306c3, pf=0x2, revision=0x17
[ 1.994988] microcode: CPU6 sig=0x306c3, pf=0x2, revision=0x17
[ 2.000898] microcode: CPU7 sig=0x306c3, pf=0x2, revision=0x17
[ 2.006839] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 2.015720] Scanning for low memory corruption every 60 seconds
[ 2.021895] Initialise system trusted keyring
[ 2.026357] audit: initializing netlink socket (disabled)
[ 2.031837] type=2000 audit(1409953701.656:1): initialized
[ 2.055046] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.062246] zbud: loaded
[ 2.064947] VFS: Disk quotas dquot_6.5.2
[ 2.068965] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.075728] fuse init (API version 7.22)
[ 2.079770] msgmni has been set to 32012
[ 2.083800] Key type big_key registered
[ 2.088025] Key type asymmetric registered
[ 2.092193] Asymmetric key parser 'x509' registered
[ 2.097158] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 2.104678] io scheduler noop registered
[ 2.108669] io scheduler deadline registered (default)
[ 2.113886] io scheduler cfq registered
[ 2.117916] pcieport 0000:00:01.0: irq 41 for MSI/MSI-X
[ 2.117998] pcieport 0000:00:01.1: irq 42 for MSI/MSI-X
[ 2.118086] pcieport 0000:00:1c.0: irq 43 for MSI/MSI-X
[ 2.118183] pcieport 0000:00:1c.1: irq 44 for MSI/MSI-X
[ 2.118239] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
[ 2.125278] pcie_pme 0000:00:01.0:pcie01: service driver pcie_pme loaded
[ 2.125285] pcieport 0000:00:01.1: Signaling PME through PCIe PME interrupt
[ 2.132322] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[ 2.138915] pcie_pme 0000:00:01.1:pcie01: service driver pcie_pme loaded
[ 2.138924] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 2.145956] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 2.152556] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[ 2.159151] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 2.159160] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
[ 2.166184] pci 0000:05:00.0: Signaling PME through PCIe PME interrupt
[ 2.172782] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
[ 2.172790] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 2.178439] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 2.185150] intel_idle: MWAIT substates: 0x42120
[ 2.185150] intel_idle: v0.4 model 0x3C
[ 2.185151] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 2.185264] ipmi message handler version 39.2
[ 2.189743] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0
[ 2.198019] ACPI: Sleep Button [SLPB]
[ 2.201768] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 2.210035] ACPI: Power Button [PWRB]
[ 2.213776] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 2.221265] ACPI: Power Button [PWRF]
[ 2.225023] ACPI: Fan [FAN0] (off)
[ 2.228513] ACPI: Fan [FAN1] (off)
[ 2.232000] ACPI: Fan [FAN2] (off)
[ 2.235489] ACPI: Fan [FAN3] (off)
[ 2.238971] ACPI: Fan [FAN4] (off)
[ 2.244043] thermal LNXTHERM:00: registered as thermal_zone0
[ 2.249781] ACPI: Thermal Zone [TZ00] (28 C)
[ 2.254242] thermal LNXTHERM:01: registered as thermal_zone1
[ 2.259978] ACPI: Thermal Zone [TZ01] (30 C)
[ 2.264357] ERST: Error Record Serialization Table (ERST) support is initialized.
[ 2.271934] pstore: Registered erst as persistent store backend
[ 2.277996] GHES: APEI firmware first mode is enabled by APEI bit and WHEA _OSC.
[ 2.285541] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 2.312561] 00:09: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 2.340552] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 2.348919] Linux agpgart interface v0.103
[ 2.353889] brd: module loaded
[ 2.357417] loop: module loaded
[ 2.360824] libphy: Fixed MDIO Bus: probed
[ 2.365038] tun: Universal TUN/TAP device driver, 1.6
[ 2.370166] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.376453] PPP generic driver version 2.4.2
[ 2.380840] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.387443] ehci-pci: EHCI PCI platform driver
[ 2.392032] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 2.397328] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.404821] ehci-pci 0000:00:1a.0: debug port 2
[ 2.413319] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 2.413328] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7434000
[ 2.427299] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 2.433134] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.439997] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.447306] usb usb1: Product: EHCI Host Controller
[ 2.452252] usb usb1: Manufacturer: Linux 3.13.0-35-generic ehci_hcd
[ 2.458669] usb usb1: SerialNumber: 0000:00:1a.0
[ 2.463427] hub 1-0:1.0: USB hub found
[ 2.467260] hub 1-0:1.0: 2 ports detected
[ 2.471473] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 2.476768] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.484259] ehci-pci 0000:00:1d.0: debug port 2
[ 2.492739] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 2.492748] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7433000
[ 2.507220] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 2.513054] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.519914] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.527223] usb usb2: Product: EHCI Host Controller
[ 2.532167] usb usb2: Manufacturer: Linux 3.13.0-35-generic ehci_hcd
[ 2.538588] usb usb2: SerialNumber: 0000:00:1d.0
[ 2.543345] hub 2-0:1.0: USB hub found
[ 2.547176] hub 2-0:1.0: 2 ports detected
[ 2.551325] ehci-platform: EHCI generic platform driver
[ 2.556629] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.562883] ohci-pci: OHCI PCI platform driver
[ 2.567404] ohci-platform: OHCI generic platform driver
[ 2.572716] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.579220] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 2.584523] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 2.592086] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 2.592109] xhci_hcd 0000:00:14.0: irq 45 for MSI/MSI-X
[ 2.592153] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.599014] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.606325] usb usb3: Product: xHCI Host Controller
[ 2.611270] usb usb3: Manufacturer: Linux 3.13.0-35-generic xhci_hcd
[ 2.617687] usb usb3: SerialNumber: 0000:00:14.0
[ 2.622448] hub 3-0:1.0: USB hub found
[ 2.626283] hub 3-0:1.0: 10 ports detected
[ 2.631726] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 2.637020] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[ 2.644521] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.651384] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.658687] usb usb4: Product: xHCI Host Controller
[ 2.663637] usb usb4: Manufacturer: Linux 3.13.0-35-generic xhci_hcd
[ 2.670055] usb usb4: SerialNumber: 0000:00:14.0
[ 2.674828] hub 4-0:1.0: USB hub found
[ 2.678664] hub 4-0:1.0: 2 ports detected
[ 2.687187] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 2.782993] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 2.954809] tsc: Refined TSC clocksource calibration: 3299.995 MHz
[ 3.202835] usb 1-1: New USB device found, idVendor=8087, idProduct=8008
[ 3.209605] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.216960] hub 1-1:1.0: USB hub found
[ 3.220938] hub 1-1:1.0: 4 ports detected
[ 3.334413] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 3.470695] usb 2-1: New USB device found, idVendor=8087, idProduct=8000
[ 3.477462] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.484825] hub 2-1:1.0: USB hub found
[ 3.488681] hub 2-1:1.0: 6 ports detected
[ 3.614142] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[ 3.652158] usb 3-1: New USB device found, idVendor=148f, idProduct=5370
[ 3.658922] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.666123] usb 3-1: Product: 802.11 n WLAN
[ 3.670372] usb 3-1: Manufacturer: Ralink
[ 3.674450] usb 3-1: SerialNumber: 1.0
[ 3.765581] i8042: No controller found
[ 3.769467] mousedev: PS/2 mouse device common for all mice
[ 3.775420] rtc_cmos 00:06: RTC can wake from S4
[ 3.780245] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 3.786435] rtc_cmos 00:06: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 3.794223] device-mapper: uevent: version 1.0.3
[ 3.798971] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[ 3.807505] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.813647] TCP: cubic registered
[ 3.817082] NET: Registered protocol family 10
[ 3.821700] NET: Registered protocol family 17
[ 3.826228] Key type dns_resolver registered
[ 3.830792] Loading compiled-in X.509 certificates
[ 3.836176] Loaded X.509 cert 'Magrathea: Glacier signing key: b1414ae96c1b0ebb7c141fa405c1f6c98e8a66f0'
[ 3.845750] registered taskstats version 1
[ 3.849954] usb 3-3: new high-speed USB device number 3 using xhci_hcd
[ 3.851345] Key type trusted registered
[ 3.852445] Key type encrypted registered
[ 3.853476] AppArmor: AppArmor sha1 policy hashing enabled
[ 3.853477] IMA: No TPM chip found, activating TPM-bypass!
[ 3.853849] regulator-dummy: disabling
[ 3.853930] Magic number: 14:409:853
[ 3.883261] rtc_cmos 00:06: setting system clock to 2014-09-05 21:48:25 UTC (1409953705)
[ 3.892394] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 3.898152] usb 3-3: New USB device found, idVendor=0000, idProduct=0001
[ 3.898153] usb 3-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.898458] hub 3-3:1.0: USB hub found
[ 3.898539] hub 3-3:1.0: 4 ports detected
[ 3.920334] EDD information not available.
[ 3.924522] PM: Hibernation image not present or could not be loaded.
[ 3.925126] Freeing unused kernel memory: 1336K (ffffffff81d1f000 - ffffffff81e6d000)
[ 3.933039] Write protecting the kernel read-only data: 12288k
[ 3.940236] Freeing unused kernel memory: 808K (ffff880001736000 - ffff880001800000)
[ 3.949047] Freeing unused kernel memory: 692K (ffff880001b53000 - ffff880001c00000)
[ 3.956888] Switched to clocksource tsc
[ 3.966177] systemd-udevd[148]: starting version 204
[ 3.974548] md: linear personality registered for level -1
[ 3.981092] pps_core: LinuxPPS API ver. 1 registered
[ 3.986425] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 3.995702] md: multipath personality registered for level -4
[ 4.001632] PTP clock support registered
[ 4.005665] md: raid0 personality registered for level 0
[ 4.005681] ahci 0000:00:1f.2: version 3.0
[ 4.005799] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X
[ 4.005873] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[ 4.005874] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst
[ 4.027002] dca service started, version 1.12.1
[ 4.027020] pm80xx 0000:02:00.0: pm80xx: driver version 0.1.37
[ 4.037529] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 4.043438] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 4.046008] scsi1 : ahci
[ 4.046053] scsi2 : ahci
[ 4.046084] scsi3 : ahci
[ 4.046114] scsi4 : ahci
[ 4.046145] scsi5 : ahci
[ 4.046174] scsi6 : ahci
[ 4.046193] ata1: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432100 irq 46
[ 4.046196] ata2: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432180 irq 46
[ 4.046197] ata3: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432200 irq 46
[ 4.046200] ata4: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432280 irq 46
[ 4.046201] ata5: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432300 irq 46
[ 4.046204] ata6: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432380 irq 46
[ 4.069697] usb 3-5: new full-speed USB device number 4 using xhci_hcd
[ 4.086848] usb 3-5: New USB device found, idVendor=051d, idProduct=0003
[ 4.086849] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.086850] usb 3-5: Product: Smart-UPS C 1500 FW:UPS 09.6 / ID=1005
[ 4.086851] usb 3-5: Manufacturer: American Power Conversion
[ 4.086851] usb 3-5: SerialNumber: 3S1424X00597
[ 4.086946] usb 3-5: ep 0x81 - rounding interval to 128 microframes, ep desc says 160 microframes
[ 4.086948] usb 3-5: ep 0x1 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 4.165151] md: raid1 personality registered for level 1
[ 4.165309] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 4.165334] e1000e 0000:00:19.0: irq 47 for MSI/MSI-X
[ 4.179985] hidraw: raw HID events driver (C) Jiri Kosina
[ 4.185503] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.5-k
[ 4.192536] igb: Copyright (c) 2007-2013 Intel Corporation.
[ 4.193596] usb 3-3.1: new low-speed USB device number 5 using xhci_hcd
[ 4.205493] igb 0000:05:00.0: irq 48 for MSI/MSI-X
[ 4.205498] igb 0000:05:00.0: irq 49 for MSI/MSI-X
[ 4.205501] igb 0000:05:00.0: irq 50 for MSI/MSI-X
[ 4.205505] igb 0000:05:00.0: irq 51 for MSI/MSI-X
[ 4.205509] igb 0000:05:00.0: irq 52 for MSI/MSI-X
[ 4.206178] usbcore: registered new interface driver usbhid
[ 4.211840] usbhid: USB HID core driver
[ 4.217599] usb 3-3.1: New USB device found, idVendor=0557, idProduct=2419
[ 4.220161] hid-generic 0003:051D:0003.0001: hiddev0,hidraw0: USB HID v1.00 Device [American Power Conversion Smart-UPS C 1500 FW:UPS 09.6 / ID=1005] on usb-0000:00:14.0-5/input0
[ 4.240667] usb 3-3.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.248106] usb 3-3.1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 4.249504] raid6: sse2x1 7925 MB/s
[ 4.250039] igb 0000:05:00.0: added PHC on eth0
[ 4.250040] igb 0000:05:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 4.250041] igb 0000:05:00.0: eth0: (PCIe:2.5Gb/s:Width x1) 00:25:90:44:09:82
[ 4.250143] igb 0000:05:00.0: eth0: PBA No: 011000-000
[ 4.250144] igb 0000:05:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
[ 4.292463] usb 3-3.1: ep 0x82 - rounding interval to 32 microframes, ep desc says 40 microframes
[ 4.302451] input: HID 0557:2419 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.1/3-3.1:1.0/input/input3
[ 4.312314] hid-generic 0003:0557:2419.0002: input,hidraw1: USB HID v1.00 Keyboard [HID 0557:2419] on usb-0000:00:14.0-3.1/input0
[ 4.317450] raid6: sse2x2 10040 MB/s
[ 4.328629] input: HID 0557:2419 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.1/3-3.1:1.1/input/input4
[ 4.338676] hid-generic 0003:0557:2419.0003: input,hidraw2: USB HID v1.00 Mouse [HID 0557:2419] on usb-0000:00:14.0-3.1/input1
[ 4.369419] ata6: SATA link down (SStatus 0 SControl 300)
[ 4.374918] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.380396] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.385385] raid6: sse2x4 10930 MB/s
[ 4.401388] ata5: SATA link down (SStatus 0 SControl 300)
[ 4.406863] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.412346] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.419423] ata3.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 4.419424] ata3.00: ATA-9: Samsung SSD 840 PRO Series, DXM06B0Q, max UDMA/133
[ 4.426732] ata3.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 4.434242] ata3.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 4.434245] ata3.00: configured for UDMA/133
[ 4.445462] scsi 3:0:0:0: Direct-Access ATA Samsung SSD 840 DXM0 PQ: 0 ANSI: 5
[ 4.453315] raid6: avx2x1 15947 MB/s
[ 4.457562] sd 3:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[ 4.465176] sd 3:0:0:0: [sda] Write Protect is off
[ 4.465312] sd 3:0:0:0: Attached scsi generic sg0 type 0
[ 4.475434] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.475443] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.485059] sda: sda1 sda2 < sda5 >
[ 4.489056] sd 3:0:0:0: [sda] Attached SCSI disk
[ 4.521248] raid6: avx2x2 19644 MB/s
[ 4.589181] raid6: avx2x4 23898 MB/s
[ 4.593006] raid6: using algorithm avx2x4 (23898 MB/s)
[ 4.598219] raid6: using avx2x2 recovery algorithm
[ 4.603938] xor: automatically using best checksumming function:
[ 4.649127] avx : 28712.000 MB/sec
[ 4.654167] async_tx: api initialized (async)
[ 4.663402] md: raid6 personality registered for level 6
[ 4.668802] md: raid5 personality registered for level 5
[ 4.674188] md: raid4 personality registered for level 4
[ 4.682317] md: raid10 personality registered for level 10
[ 4.697492] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 4.705313] EXT4-fs (sda1): write access will be enabled during recovery
[ 4.723814] EXT4-fs (sda1): recovery complete
[ 4.729544] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 4.910633] scsi0 : pm80xx
[ 4.913684] pm80xx 0000:02:00.0: irq 53 for MSI/MSI-X
[ 4.913698] pm80xx 0000:02:00.0: irq 54 for MSI/MSI-X
[ 4.913702] pm80xx 0000:02:00.0: irq 55 for MSI/MSI-X
[ 4.913706] pm80xx 0000:02:00.0: irq 56 for MSI/MSI-X
[ 4.913710] pm80xx 0000:02:00.0: irq 57 for MSI/MSI-X
[ 4.913714] pm80xx 0000:02:00.0: irq 58 for MSI/MSI-X
[ 4.913718] pm80xx 0000:02:00.0: irq 59 for MSI/MSI-X
[ 4.913722] pm80xx 0000:02:00.0: irq 60 for MSI/MSI-X
[ 4.913725] pm80xx 0000:02:00.0: irq 61 for MSI/MSI-X
[ 4.913729] pm80xx 0000:02:00.0: irq 62 for MSI/MSI-X
[ 4.913733] pm80xx 0000:02:00.0: irq 63 for MSI/MSI-X
[ 4.913737] pm80xx 0000:02:00.0: irq 64 for MSI/MSI-X
[ 4.913740] pm80xx 0000:02:00.0: irq 65 for MSI/MSI-X
[ 4.913744] pm80xx 0000:02:00.0: irq 66 for MSI/MSI-X
[ 4.913748] pm80xx 0000:02:00.0: irq 67 for MSI/MSI-X
[ 4.913751] pm80xx 0000:02:00.0: irq 68 for MSI/MSI-X
[ 4.913755] pm80xx 0000:02:00.0: irq 69 for MSI/MSI-X
[ 4.913759] pm80xx 0000:02:00.0: irq 70 for MSI/MSI-X
[ 4.913762] pm80xx 0000:02:00.0: irq 71 for MSI/MSI-X
[ 4.913766] pm80xx 0000:02:00.0: irq 72 for MSI/MSI-X
[ 4.913769] pm80xx 0000:02:00.0: irq 73 for MSI/MSI-X
[ 4.913773] pm80xx 0000:02:00.0: irq 74 for MSI/MSI-X
[ 4.913777] pm80xx 0000:02:00.0: irq 75 for MSI/MSI-X
[ 4.913780] pm80xx 0000:02:00.0: irq 76 for MSI/MSI-X
[ 4.913784] pm80xx 0000:02:00.0: irq 77 for MSI/MSI-X
[ 4.913787] pm80xx 0000:02:00.0: irq 78 for MSI/MSI-X
[ 4.913791] pm80xx 0000:02:00.0: irq 79 for MSI/MSI-X
[ 4.913795] pm80xx 0000:02:00.0: irq 80 for MSI/MSI-X
[ 4.913799] pm80xx 0000:02:00.0: irq 81 for MSI/MSI-X
[ 4.913802] pm80xx 0000:02:00.0: irq 82 for MSI/MSI-X
[ 4.913806] pm80xx 0000:02:00.0: irq 83 for MSI/MSI-X
[ 4.913810] pm80xx 0000:02:00.0: irq 84 for MSI/MSI-X
[ 4.913813] pm80xx 0000:02:00.0: irq 85 for MSI/MSI-X
[ 4.913817] pm80xx 0000:02:00.0: irq 86 for MSI/MSI-X
[ 4.913820] pm80xx 0000:02:00.0: irq 87 for MSI/MSI-X
[ 4.913824] pm80xx 0000:02:00.0: irq 88 for MSI/MSI-X
[ 4.913827] pm80xx 0000:02:00.0: irq 89 for MSI/MSI-X
[ 4.913831] pm80xx 0000:02:00.0: irq 90 for MSI/MSI-X
[ 4.913835] pm80xx 0000:02:00.0: irq 91 for MSI/MSI-X
[ 4.913838] pm80xx 0000:02:00.0: irq 92 for MSI/MSI-X
[ 4.913842] pm80xx 0000:02:00.0: irq 93 for MSI/MSI-X
[ 4.913845] pm80xx 0000:02:00.0: irq 94 for MSI/MSI-X
[ 4.913849] pm80xx 0000:02:00.0: irq 95 for MSI/MSI-X
[ 4.913853] pm80xx 0000:02:00.0: irq 96 for MSI/MSI-X
[ 4.913856] pm80xx 0000:02:00.0: irq 97 for MSI/MSI-X
[ 4.913860] pm80xx 0000:02:00.0: irq 98 for MSI/MSI-X
[ 4.913864] pm80xx 0000:02:00.0: irq 99 for MSI/MSI-X
[ 4.913867] pm80xx 0000:02:00.0: irq 100 for MSI/MSI-X
[ 4.913871] pm80xx 0000:02:00.0: irq 101 for MSI/MSI-X
[ 4.913874] pm80xx 0000:02:00.0: irq 102 for MSI/MSI-X
[ 4.913878] pm80xx 0000:02:00.0: irq 103 for MSI/MSI-X
[ 4.913882] pm80xx 0000:02:00.0: irq 104 for MSI/MSI-X
[ 4.913885] pm80xx 0000:02:00.0: irq 105 for MSI/MSI-X
[ 4.913889] pm80xx 0000:02:00.0: irq 106 for MSI/MSI-X
[ 4.913893] pm80xx 0000:02:00.0: irq 107 for MSI/MSI-X
[ 4.913896] pm80xx 0000:02:00.0: irq 108 for MSI/MSI-X
[ 4.913900] pm80xx 0000:02:00.0: irq 109 for MSI/MSI-X
[ 4.913903] pm80xx 0000:02:00.0: irq 110 for MSI/MSI-X
[ 4.913907] pm80xx 0000:02:00.0: irq 111 for MSI/MSI-X
[ 4.913911] pm80xx 0000:02:00.0: irq 112 for MSI/MSI-X
[ 4.913914] pm80xx 0000:02:00.0: irq 113 for MSI/MSI-X
[ 4.913918] pm80xx 0000:02:00.0: irq 114 for MSI/MSI-X
[ 4.913922] pm80xx 0000:02:00.0: irq 115 for MSI/MSI-X
[ 4.913925] pm80xx 0000:02:00.0: irq 116 for MSI/MSI-X
[ 4.928948] systemd-udevd[153]: renamed network interface eth0 to em1
[ 4.929069] e1000e 0000:00:19.0 eth0: registered PHC clock
[ 4.929070] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:44:09:83
[ 4.929071] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 4.929105] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: 0100FF-0FF
[ 4.977001] systemd-udevd[150]: renamed network interface eth0 to em2
[ 5.414147] sas: phy-0:0 added to port-0:0, phy_mask:0x1 (5003048001108c3f)
[ 5.414152] sas: phy1 matched wide port0
[ 5.414155] sas: phy-0:1 added to port-0:0, phy_mask:0x3 (5003048001108c3f)
[ 5.414160] sas: DOING DISCOVERY on port 0, pid:196
[ 5.414575] sas: ex 5003048001108c3f phy00:S:A attached: 50000d1106da2000 (host)
[ 5.414756] sas: ex 5003048001108c3f phy01:S:A attached: 50000d1106da2000 (host)
[ 5.414935] sas: ex 5003048001108c3f phy02:S:A attached: 50000d1106da2000 (host)
[ 5.415117] sas: ex 5003048001108c3f phy03:S:A attached: 50000d1106da2000 (host)
[ 5.415364] sas: ex 5003048001108c3f phy04:U:0 attached: 0000000000000000 (no device)
[ 5.415666] sas: ex 5003048001108c3f phy05:U:0 attached: 0000000000000000 (no device)
[ 5.415903] sas: ex 5003048001108c3f phy06:U:0 attached: 0000000000000000 (no device)
[ 5.416207] sas: ex 5003048001108c3f phy07:U:0 attached: 0000000000000000 (no device)
[ 5.416445] sas: ex 5003048001108c3f phy08:U:0 attached: 0000000000000000 (no device)
[ 5.416691] sas: ex 5003048001108c3f phy09:U:0 attached: 0000000000000000 (no device)
[ 5.416927] sas: ex 5003048001108c3f phy10:U:0 attached: 0000000000000000 (no device)
[ 5.417159] sas: ex 5003048001108c3f phy11:U:0 attached: 0000000000000000 (no device)
[ 5.417392] sas: ex 5003048001108c3f phy12:U:A attached: 5003048001108c0c (stp)
[ 5.417621] sas: ex 5003048001108c3f phy13:U:A attached: 5003048001108c0d (stp)
[ 5.417853] sas: ex 5003048001108c3f phy14:U:A attached: 5003048001108c0e (stp)
[ 5.418081] sas: ex 5003048001108c3f phy15:U:A attached: 5003048001108c0f (stp)
[ 5.418312] sas: ex 5003048001108c3f phy16:U:A attached: 5003048001108c10 (stp)
[ 5.418544] sas: ex 5003048001108c3f phy17:U:A attached: 5003048001108c11 (stp)
[ 5.418772] sas: ex 5003048001108c3f phy18:U:0 attached: 0000000000000000 (no device)
[ 5.419001] sas: ex 5003048001108c3f phy19:U:0 attached: 0000000000000000 (no device)
[ 5.419231] sas: ex 5003048001108c3f phy20:U:0 attached: 0000000000000000 (no device)
[ 5.419459] sas: ex 5003048001108c3f phy21:U:0 attached: 0000000000000000 (no device)
[ 5.419688] sas: ex 5003048001108c3f phy22:U:0 attached: 0000000000000000 (no device)
[ 5.419917] sas: ex 5003048001108c3f phy23:U:0 attached: 0000000000000000 (no device)
[ 5.420147] sas: ex 5003048001108c3f phy24:U:0 attached: 0000000000000000 (no device)
[ 5.420385] sas: ex 5003048001108c3f phy25:U:0 attached: 0000000000000000 (no device)
[ 5.420599] sas: ex 5003048001108c3f phy26:U:0 attached: 0000000000000000 (no device)
[ 5.420813] sas: ex 5003048001108c3f phy27:U:0 attached: 0000000000000000 (no device)
[ 5.421043] sas: ex 5003048001108c3f phy28:U:0 attached: 0000000000000000 (no device)
[ 5.421277] sas: ex 5003048001108c3f phy29:U:0 attached: 0000000000000000 (no device)
[ 5.421511] sas: ex 5003048001108c3f phy30:U:0 attached: 0000000000000000 (no device)
[ 5.421742] sas: ex 5003048001108c3f phy31:U:0 attached: 0000000000000000 (no device)
[ 5.421971] sas: ex 5003048001108c3f phy32:U:0 attached: 0000000000000000 (no device)
[ 5.422200] sas: ex 5003048001108c3f phy33:U:0 attached: 0000000000000000 (no device)
[ 5.422430] sas: ex 5003048001108c3f phy34:U:0 attached: 0000000000000000 (no device)
[ 5.422657] sas: ex 5003048001108c3f phy35:U:0 attached: 0000000000000000 (no device)
[ 5.422883] sas: ex 5003048001108c3f phy36:D:A attached: 5003048001108c3d (host+target)
[ 5.423108] sas: ex 5003048001108c3f phy37:D:0 attached: 0000000000000000 (no device)
[ 5.480386] sas: DONE DISCOVERY on port 0, pid:196, result:0
[ 5.480390] sas: phy2 matched wide port0
[ 5.480395] sas: phy-0:2 added to port-0:0, phy_mask:0x7 (5003048001108c3f)
[ 5.480439] sas: phy-0:4 added to port-0:1, phy_mask:0x10 (50030480010f713f)
[ 5.480441] sas: phy3 matched wide port0
[ 5.480442] sas: phy-0:3 added to port-0:0, phy_mask:0xf (5003048001108c3f)
[ 5.480443] sas: phy5 matched wide port1
[ 5.480445] sas: phy-0:5 added to port-0:1, phy_mask:0x30 (50030480010f713f)
[ 5.480446] sas: phy7 matched wide port1
[ 5.480448] sas: phy-0:7 added to port-0:1, phy_mask:0xb0 (50030480010f713f)
[ 5.480449] sas: phy6 matched wide port1
[ 5.480451] sas: phy-0:6 added to port-0:1, phy_mask:0xf0 (50030480010f713f)
[ 5.480461] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 5.480475] sas: ata7: end_device-0:0:12: dev error handler
[ 5.480492] sas: ata8: end_device-0:0:13: dev error handler
[ 5.480493] sas: ata9: end_device-0:0:14: dev error handler
[ 5.480498] sas: ata10: end_device-0:0:15: dev error handler
[ 5.480502] sas: ata11: end_device-0:0:16: dev error handler
[ 5.480632] sas: ata12: end_device-0:0:17: dev error handler
[ 7.639340] ata7.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.639437] ata8.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.639438] ata8.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.639548] ata9.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.639549] ata9.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.639820] ata10.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.639820] ata10.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.639963] ata8.00: configured for UDMA/133
[ 7.640069] ata9.00: configured for UDMA/133
[ 7.640350] ata10.00: configured for UDMA/133
[ 7.709554] ata7.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.717075] ata7.00: configured for UDMA/133
[ 27.514797] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 27.514824] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 27.671580] ata11.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 27.678454] ata11.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 27.683249] ata12.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 27.683250] ata12.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 27.683769] ata12.00: configured for UDMA/133
[ 27.704530] ata11.00: configured for UDMA/133
[ 27.708992] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 27.722811] scsi 0:0:0:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.731153] scsi 0:0:1:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.739484] scsi 0:0:2:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.747812] scsi 0:0:3:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.756143] scsi 0:0:4:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.764476] scsi 0:0:5:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.773048] scsi 0:0:6:0: Enclosure LSI SAS2X36 0e12 PQ: 0 ANSI: 5
[ 27.782523] sas: DOING DISCOVERY on port 1, pid:196
[ 27.783139] sas: ex 50030480010f713f phy00:S:A attached: 50000d1106da2000 (host)
[ 27.783386] sas: ex 50030480010f713f phy01:S:A attached: 50000d1106da2000 (host)
[ 27.783702] sas: ex 50030480010f713f phy02:S:A attached: 50000d1106da2000 (host)
[ 27.783957] sas: ex 50030480010f713f phy03:S:A attached: 50000d1106da2000 (host)
[ 27.784270] sas: ex 50030480010f713f phy04:U:0 attached: 0000000000000000 (no device)
[ 27.784522] sas: ex 50030480010f713f phy05:U:0 attached: 0000000000000000 (no device)
[ 27.784836] sas: ex 50030480010f713f phy06:U:0 attached: 0000000000000000 (no device)
[ 27.785096] sas: ex 50030480010f713f phy07:U:0 attached: 0000000000000000 (no device)
[ 27.785382] sas: ex 50030480010f713f phy08:D:1 attached: 0000000000000000 (no device)
[ 27.785630] sas: ex 50030480010f713f phy09:D:1 attached: 0000000000000000 (no device)
[ 27.785870] sas: ex 50030480010f713f phy10:D:1 attached: 0000000000000000 (no device)
[ 27.786107] sas: ex 50030480010f713f phy11:D:1 attached: 0000000000000000 (no device)
[ 27.786345] sas: ex 50030480010f713f phy12:U:A attached: 50030480010f712c (stp)
[ 27.786588] sas: ex 50030480010f713f phy13:U:A attached: 50030480010f712d (stp)
[ 27.786826] sas: ex 50030480010f713f phy14:U:A attached: 50030480010f712e (stp)
[ 27.787064] sas: ex 50030480010f713f phy15:U:A attached: 50030480010f712f (stp)
[ 27.787305] sas: ex 50030480010f713f phy16:U:A attached: 50030480010f7130 (stp)
[ 27.787544] sas: ex 50030480010f713f phy17:U:0 attached: 0000000000000000 (no device)
[ 27.787781] sas: ex 50030480010f713f phy18:U:0 attached: 0000000000000000 (no device)
[ 27.788018] sas: ex 50030480010f713f phy19:U:0 attached: 0000000000000000 (no device)
[ 27.788254] sas: ex 50030480010f713f phy20:U:0 attached: 0000000000000000 (no device)
[ 27.788492] sas: ex 50030480010f713f phy21:U:0 attached: 0000000000000000 (no device)
[ 27.788731] sas: ex 50030480010f713f phy22:U:0 attached: 0000000000000000 (no device)
[ 27.788970] sas: ex 50030480010f713f phy23:U:0 attached: 0000000000000000 (no device)
[ 27.789206] sas: ex 50030480010f713f phy24:D:1 attached: 0000000000000000 (no device)
[ 27.789444] sas: ex 50030480010f713f phy25:D:1 attached: 0000000000000000 (no device)
[ 27.789682] sas: ex 50030480010f713f phy26:D:1 attached: 0000000000000000 (no device)
[ 27.789920] sas: ex 50030480010f713f phy27:D:1 attached: 0000000000000000 (no device)
[ 27.790155] sas: ex 50030480010f713f phy28:D:A attached: 50030480010f713d (host+target)
[ 27.790391] sas: ex 50030480010f713f phy29:D:0 attached: 0000000000000000 (no device)
[ 27.846476] sas: DONE DISCOVERY on port 1, pid:196, result:0
[ 27.846480] sas: broadcast received: 9
[ 27.846483] sas: broadcast received: 9
[ 27.846484] sas: broadcast received: 9
[ 27.846484] sas: broadcast received: 9
[ 27.846508] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 27.846551] sas: ata7: end_device-0:0:12: dev error handler
[ 27.846575] sas: ata8: end_device-0:0:13: dev error handler
[ 27.846581] sas: ata9: end_device-0:0:14: dev error handler
[ 27.846582] sas: ata10: end_device-0:0:15: dev error handler
[ 27.846588] sas: ata11: end_device-0:0:16: dev error handler
[ 27.846589] sas: ata12: end_device-0:0:17: dev error handler
[ 27.846595] sas: ata14: end_device-0:1:13: dev error handler
[ 27.846596] sas: ata13: end_device-0:1:12: dev error handler
[ 27.846597] sas: ata15: end_device-0:1:14: dev error handler
[ 27.846613] sas: ata16: end_device-0:1:15: dev error handler
[ 27.846615] sas: ata17: end_device-0:1:16: dev error handler
[ 30.005465] ata14.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.005664] ata15.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.005666] ata15.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.005754] ata13.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.005755] ata13.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.005940] ata17.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.005941] ata17.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.006136] ata16.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.006136] ata16.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.006190] ata15.00: configured for UDMA/133
[ 30.006467] ata13.00: configured for UDMA/133
[ 30.006488] ata17.00: configured for UDMA/133
[ 30.006852] ata16.00: configured for UDMA/133
[ 30.085554] ata14.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.093334] ata14.00: configured for UDMA/133
[ 30.097796] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 30.100444] scsi 0:0:7:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.108801] scsi 0:0:8:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.117153] scsi 0:0:9:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.125503] scsi 0:0:10:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.133936] scsi 0:0:11:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.142691] scsi 0:0:12:0: Enclosure LSI SAS2X28 0e12 PQ: 0 ANSI: 5
[ 30.152243] sas: REVALIDATING DOMAIN on port 0, pid:196
[ 30.155348] sas: Expander phy change count has changed
[ 30.158072] sas: ex 5003048001108c3f phy12 originated BROADCAST(CHANGE)
[ 30.158498] sas: ex 5003048001108c3f phy 0xc broadcast flutter
[ 30.158717] sas: ex 5003048001108c3f phy13 originated BROADCAST(CHANGE)
[ 30.159142] sas: ex 5003048001108c3f phy 0xd broadcast flutter
[ 30.159362] sas: ex 5003048001108c3f phy14 originated BROADCAST(CHANGE)
[ 30.159787] sas: ex 5003048001108c3f phy 0xe broadcast flutter
[ 30.159999] sas: ex 5003048001108c3f phy15 originated BROADCAST(CHANGE)
[ 30.160393] sas: ex 5003048001108c3f phy 0xf broadcast flutter
[ 30.160606] sas: ex 5003048001108c3f phy16 originated BROADCAST(CHANGE)
[ 30.161031] sas: ex 5003048001108c3f phy 0x10 broadcast flutter
[ 30.161243] sas: ex 5003048001108c3f phy17 originated BROADCAST(CHANGE)
[ 30.161667] sas: ex 5003048001108c3f phy 0x11 broadcast flutter
[ 30.165656] sas: done REVALIDATING DOMAIN on port 0, pid:196, res 0x0
[ 30.165677] sas: REVALIDATING DOMAIN on port 0, pid:196
[ 30.165721] sas: done REVALIDATING DOMAIN on port 0, pid:196, res 0x0
[ 30.165723] sas: broadcast received: 9
[ 30.165725] sas: broadcast received: 9
[ 30.165726] sas: broadcast received: 9
[ 30.165727] sas: broadcast received: 9
[ 30.165728] sas: REVALIDATING DOMAIN on port 1, pid:196
[ 30.165788] sd 0:0:0:0: [sdb] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.165792] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 30.165876] sd 0:0:1:0: Attached scsi generic sg2 type 0
[ 30.165890] sd 0:0:1:0: [sdc] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.165891] sd 0:0:1:0: [sdc] 4096-byte physical blocks
[ 30.165942] sd 0:0:1:0: [sdc] Write Protect is off
[ 30.165943] sd 0:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[ 30.165958] sd 0:0:2:0: [sdd] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.165960] sd 0:0:2:0: [sdd] 4096-byte physical blocks
[ 30.165961] sd 0:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.165965] sd 0:0:2:0: Attached scsi generic sg3 type 0
[ 30.165992] sd 0:0:2:0: [sdd] Write Protect is off
[ 30.165994] sd 0:0:2:0: [sdd] Mode Sense: 00 3a 00 00
[ 30.166013] sd 0:0:2:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166052] sd 0:0:3:0: [sde] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166053] sd 0:0:3:0: [sde] 4096-byte physical blocks
[ 30.166067] sd 0:0:3:0: Attached scsi generic sg4 type 0
[ 30.166093] sd 0:0:3:0: [sde] Write Protect is off
[ 30.166094] sd 0:0:3:0: [sde] Mode Sense: 00 3a 00 00
[ 30.166109] sd 0:0:3:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166147] sd 0:0:4:0: [sdf] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166148] sd 0:0:4:0: [sdf] 4096-byte physical blocks
[ 30.166165] sd 0:0:4:0: Attached scsi generic sg5 type 0
[ 30.166169] sd 0:0:4:0: [sdf] Write Protect is off
[ 30.166170] sd 0:0:4:0: [sdf] Mode Sense: 00 3a 00 00
[ 30.166180] sd 0:0:4:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166309] sd 0:0:5:0: Attached scsi generic sg6 type 0
[ 30.166319] sd 0:0:5:0: [sdg] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166320] sd 0:0:5:0: [sdg] 4096-byte physical blocks
[ 30.166334] sd 0:0:5:0: [sdg] Write Protect is off
[ 30.166334] sd 0:0:5:0: [sdg] Mode Sense: 00 3a 00 00
[ 30.166340] sd 0:0:5:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166415] scsi 0:0:6:0: Attached scsi generic sg7 type 13
[ 30.166520] sd 0:0:7:0: Attached scsi generic sg8 type 0
[ 30.166527] sd 0:0:7:0: [sdh] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166528] sd 0:0:7:0: [sdh] 4096-byte physical blocks
[ 30.166556] sd 0:0:7:0: [sdh] Write Protect is off
[ 30.166557] sd 0:0:7:0: [sdh] Mode Sense: 00 3a 00 00
[ 30.166567] sd 0:0:7:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166597] sd 0:0:8:0: [sdi] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166598] sd 0:0:8:0: [sdi] 4096-byte physical blocks
[ 30.166612] sd 0:0:8:0: [sdi] Write Protect is off
[ 30.166613] sd 0:0:8:0: [sdi] Mode Sense: 00 3a 00 00
[ 30.166618] sd 0:0:8:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166625] sd 0:0:8:0: Attached scsi generic sg9 type 0
[ 30.166720] sd 0:0:9:0: [sdj] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166721] sd 0:0:9:0: [sdj] 4096-byte physical blocks
[ 30.166734] sd 0:0:9:0: [sdj] Write Protect is off
[ 30.166734] sd 0:0:9:0: [sdj] Mode Sense: 00 3a 00 00
[ 30.166740] sd 0:0:9:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166746] sd 0:0:9:0: Attached scsi generic sg10 type 0
[ 30.166840] sd 0:0:10:0: [sdk] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166841] sd 0:0:10:0: [sdk] 4096-byte physical blocks
[ 30.166854] sd 0:0:10:0: [sdk] Write Protect is off
[ 30.166855] sd 0:0:10:0: [sdk] Mode Sense: 00 3a 00 00
[ 30.166859] sd 0:0:10:0: Attached scsi generic sg11 type 0
[ 30.166860] sd 0:0:10:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166953] sd 0:0:11:0: [sdl] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166954] sd 0:0:11:0: [sdl] 4096-byte physical blocks
[ 30.166971] sd 0:0:11:0: Attached scsi generic sg12 type 0
[ 30.166975] sd 0:0:11:0: [sdl] Write Protect is off
[ 30.166977] sd 0:0:11:0: [sdl] Mode Sense: 00 3a 00 00
[ 30.166985] sd 0:0:11:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.167085] scsi 0:0:12:0: Attached scsi generic sg13 type 13
[ 30.168007] sas: Expander phy change count has changed
[ 30.170193] sas: ex 50030480010f713f phy12 originated BROADCAST(CHANGE)
[ 30.170535] sas: ex 50030480010f713f phy 0xc broadcast flutter
[ 30.170704] sas: ex 50030480010f713f phy13 originated BROADCAST(CHANGE)
[ 30.171043] sas: ex 50030480010f713f phy 0xd broadcast flutter
[ 30.171211] sas: ex 50030480010f713f phy14 originated BROADCAST(CHANGE)
[ 30.171549] sas: ex 50030480010f713f phy 0xe broadcast flutter
[ 30.171717] sas: ex 50030480010f713f phy15 originated BROADCAST(CHANGE)
[ 30.172055] sas: ex 50030480010f713f phy 0xf broadcast flutter
[ 30.172224] sas: ex 50030480010f713f phy16 originated BROADCAST(CHANGE)
[ 30.172562] sas: ex 50030480010f713f phy 0x10 broadcast flutter
[ 30.174785] sas: done REVALIDATING DOMAIN on port 1, pid:196, res 0x0
[ 30.517279] sd 0:0:0:0: [sdb] 4096-byte physical blocks
[ 30.522591] sd 0:0:0:0: [sdb] Write Protect is off
[ 30.527452] sd 0:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 30.527458] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.899582] random: nonblocking pool is initialized
[ 30.932613] sdj: sdj1
[ 30.935171] sd 0:0:9:0: [sdj] Attached SCSI disk
[ 30.938259] sdd: sdd1
[ 30.938606] sd 0:0:2:0: [sdd] Attached SCSI disk
[ 30.944896] sdh: sdh1
[ 30.945162] sd 0:0:7:0: [sdh] Attached SCSI disk
[ 30.960954] sdf: sdf1
[ 30.961969] sdc: sdc1
[ 30.962317] sd 0:0:1:0: [sdc] Attached SCSI disk
[ 30.966518] sdk: sdk1
[ 30.966573] sde: sde1
[ 30.966739] sd 0:0:10:0: [sdk] Attached SCSI disk
[ 30.966767] sd 0:0:3:0: [sde] Attached SCSI disk
[ 30.969636] sdg: sdg1
[ 30.969813] sd 0:0:5:0: [sdg] Attached SCSI disk
[ 30.975786] sdi: sdi1
[ 30.975897] sd 0:0:8:0: [sdi] Attached SCSI disk
[ 30.987891] sdl: sdl1
[ 30.988178] sd 0:0:11:0: [sdl] Attached SCSI disk
[ 31.006364] sd 0:0:4:0: [sdf] Attached SCSI disk
[ 31.333034] sdb: sdb1
[ 31.335677] sd 0:0:0:0: [sdb] Attached SCSI disk
[ 31.403662] ses 0:0:6:0: Attached Enclosure device
[ 31.408541] ses 0:0:12:0: Attached Enclosure device
[ 31.436012] md: bind<sdg1>
[ 31.439935] md: bind<sdd1>
[ 31.443739] md: bind<sdi1>
[ 31.447863] md: bind<sdh1>
[ 31.452255] md: bind<sdc1>
[ 31.456800] md: bind<sde1>
[ 31.461230] md: bind<sdf1>
[ 31.466009] md: bind<sdb1>
[ 31.470873] md: bind<sdk1>
[ 31.475718] md: bind<sdl1>
[ 31.480867] md: bind<sdj1>
[ 31.486034] md/raid:md127: device sdj1 operational as raid disk 8
[ 31.492205] md/raid:md127: device sdk1 operational as raid disk 9
[ 31.498365] md/raid:md127: device sdb1 operational as raid disk 0
[ 31.504520] md/raid:md127: device sdf1 operational as raid disk 4
[ 31.510676] md/raid:md127: device sde1 operational as raid disk 3
[ 31.516834] md/raid:md127: device sdc1 operational as raid disk 1
[ 31.522991] md/raid:md127: device sdh1 operational as raid disk 6
[ 31.529151] md/raid:md127: device sdi1 operational as raid disk 7
[ 31.535310] md/raid:md127: device sdd1 operational as raid disk 2
[ 31.541465] md/raid:md127: device sdg1 operational as raid disk 5
[ 31.547990] md/raid:md127: allocated 0kB
[ 31.552036] md/raid:md127: raid level 6 active with 10 out of 10 devices, algorithm 2
[ 31.568972] RAID conf printout:
[ 31.568973] --- level:6 rd:10 wd:10
[ 31.568974] disk 0, o:1, dev:sdb1
[ 31.568975] disk 1, o:1, dev:sdc1
[ 31.568975] disk 2, o:1, dev:sdd1
[ 31.568976] disk 3, o:1, dev:sde1
[ 31.568976] disk 4, o:1, dev:sdf1
[ 31.568977] disk 5, o:1, dev:sdg1
[ 31.568977] disk 6, o:1, dev:sdh1
[ 31.568978] disk 7, o:1, dev:sdi1
[ 31.568978] disk 8, o:1, dev:sdj1
[ 31.568979] disk 9, o:1, dev:sdk1
[ 31.568991] md127: detected capacity change from 0 to 47998917148672
[ 31.605268] md127: unknown partition table
[ 31.783548] bio: create slab <bio-1> at 1
[ 32.154351] init: plymouth-upstart-bridge main process (298) terminated with status 1
[ 32.162329] init: plymouth-upstart-bridge main process ended, respawning
[ 32.172180] init: plymouth-upstart-bridge main process (308) terminated with status 1
[ 32.180113] init: plymouth-upstart-bridge main process ended, respawning
[ 32.189575] init: plymouth-upstart-bridge main process (316) terminated with status 1
[ 32.197517] init: plymouth-upstart-bridge main process ended, respawning
[ 32.205839] init: plymouth-upstart-bridge main process (321) terminated with status 1
[ 32.213809] init: plymouth-upstart-bridge main process ended, respawning
[ 32.304552] Adding 16733180k swap on /dev/sda5. Priority:-1 extents:1 across:16733180k SSFS
[ 32.321301] IPv6: ADDRCONF(NETDEV_UP): em1: link is not ready
[ 32.321305] IPv6: ADDRCONF(NETDEV_UP): em2: link is not ready
[ 32.338681] systemd-udevd[428]: starting version 204
[ 32.357558] lp: driver loaded but no devices found
[ 32.368153] IPMI System Interface driver.
[ 32.368171] ipmi_si: probing via ACPI
[ 32.368186] ipmi_si 00:0c: [io 0x0ca2] regsize 1 spacing 1 irq 0
[ 32.368187] ipmi_si: Adding ACPI-specified kcs state machine
[ 32.368195] ipmi_si: probing via SMBIOS
[ 32.368196] ipmi_si: SMBIOS: io 0xca2 regsize 1 spacing 1 irq 0
[ 32.368196] ipmi_si: Adding SMBIOS-specified kcs state machine duplicate interface
[ 32.368197] ipmi_si: probing via SPMI
[ 32.368198] ipmi_si: SPMI: io 0xca2 regsize 1 spacing 1 irq 0
[ 32.368199] ipmi_si: Adding SPMI-specified kcs state machine duplicate interface
[ 32.368200] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
[ 32.415453] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 32.418138] ACPI Warning: 0x0000000000001828-0x000000000000182f SystemIO conflicts with Region \PMIO 1 (20131115/utaddress-251)
[ 32.418142] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 32.418145] ACPI Warning: 0x0000000000001c30-0x0000000000001c3f SystemIO conflicts with Region \GPRL 1 (20131115/utaddress-251)
[ 32.418147] ACPI Warning: 0x0000000000001c30-0x0000000000001c3f SystemIO conflicts with Region \GPR_ 2 (20131115/utaddress-251)
[ 32.418149] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 32.418150] ACPI Warning: 0x0000000000001c00-0x0000000000001c2f SystemIO conflicts with Region \GPRL 1 (20131115/utaddress-251)
[ 32.418151] ACPI Warning: 0x0000000000001c00-0x0000000000001c2f SystemIO conflicts with Region \GPR_ 2 (20131115/utaddress-251)
[ 32.418153] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 32.418154] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 32.420762] cfg80211: Calling CRDA to update world regulatory domain
[ 32.478236] ipmi_si 00:0c: Found new BMC (man_id: 0x002a7c, prod_id: 0x0801, dev_id: 0x20)
[ 32.478239] ipmi_si 00:0c: IPMI kcs interface initialized
[ 32.597956] usb 3-1: reset high-speed USB device number 2 using xhci_hcd
[ 32.624825] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f840
[ 32.624827] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f800
[ 32.624828] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f880
[ 32.624829] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f8c0
[ 32.624830] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f900
[ 32.624831] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f940
[ 32.624832] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f980
[ 32.625132] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0502 detected
[ 32.634683] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5370 detected
[ 32.643264] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 32.643458] usbcore: registered new interface driver rt2800usb
[ 32.884598] sd 0:0:5:0: [sdg] command ffff880404ebd700 timed out
[ 32.884681] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.884684] sas: ata12: end_device-0:0:17: cmd error handler
[ 32.884695] sas: ata7: end_device-0:0:12: dev error handler
[ 32.884704] sas: ata8: end_device-0:0:13: dev error handler
[ 32.884708] sas: ata9: end_device-0:0:14: dev error handler
[ 32.884712] sas: ata10: end_device-0:0:15: dev error handler
[ 32.884717] sas: ata11: end_device-0:0:16: dev error handler
[ 32.884720] sas: ata12: end_device-0:0:17: dev error handler
[ 32.884728] sas: ata13: end_device-0:1:12: dev error handler
[ 32.884731] sas: ata14: end_device-0:1:13: dev error handler
[ 32.884735] sas: ata15: end_device-0:1:14: dev error handler
[ 32.884738] sas: ata16: end_device-0:1:15: dev error handler
[ 32.884741] sas: ata17: end_device-0:1:16: dev error handler
[ 32.884747] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.884896] sd 0:0:11:0: [sdl] command ffff8800d954ec00 timed out
[ 32.885205] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.885207] sas: ata17: end_device-0:1:16: cmd error handler
[ 32.885215] sas: ata7: end_device-0:0:12: dev error handler
[ 32.885221] sas: ata8: end_device-0:0:13: dev error handler
[ 32.885225] sas: ata9: end_device-0:0:14: dev error handler
[ 32.885228] sas: ata10: end_device-0:0:15: dev error handler
[ 32.885231] sas: ata11: end_device-0:0:16: dev error handler
[ 32.885234] sas: ata12: end_device-0:0:17: dev error handler
[ 32.885238] sas: ata13: end_device-0:1:12: dev error handler
[ 32.885241] sas: ata14: end_device-0:1:13: dev error handler
[ 32.885244] sas: ata15: end_device-0:1:14: dev error handler
[ 32.885247] sas: ata16: end_device-0:1:15: dev error handler
[ 32.885250] sas: ata17: end_device-0:1:16: dev error handler
[ 32.885259] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.885515] sd 0:0:7:0: [sdh] command ffff8800d954eb00 timed out
[ 32.885742] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.885744] sas: ata13: end_device-0:1:12: cmd error handler
[ 32.885751] sas: ata7: end_device-0:0:12: dev error handler
[ 32.885756] sas: ata8: end_device-0:0:13: dev error handler
[ 32.885759] sas: ata9: end_device-0:0:14: dev error handler
[ 32.885761] sas: ata10: end_device-0:0:15: dev error handler
[ 32.885764] sas: ata11: end_device-0:0:16: dev error handler
[ 32.885767] sas: ata12: end_device-0:0:17: dev error handler
[ 32.885769] sas: ata13: end_device-0:1:12: dev error handler
[ 32.885775] sas: ata14: end_device-0:1:13: dev error handler
[ 32.885778] sas: ata15: end_device-0:1:14: dev error handler
[ 32.885780] sas: ata16: end_device-0:1:15: dev error handler
[ 32.885783] sas: ata17: end_device-0:1:16: dev error handler
[ 32.885787] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.885946] sd 0:0:1:0: [sdc] command ffff880404e68f00 timed out
[ 32.885984] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.885986] sas: ata8: end_device-0:0:13: cmd error handler
[ 32.885993] sas: ata7: end_device-0:0:12: dev error handler
[ 32.885998] sas: ata8: end_device-0:0:13: dev error handler
[ 32.886005] sas: ata9: end_device-0:0:14: dev error handler
[ 32.886007] sas: ata10: end_device-0:0:15: dev error handler
[ 32.886009] sas: ata11: end_device-0:0:16: dev error handler
[ 32.886010] sas: ata12: end_device-0:0:17: dev error handler
[ 32.886012] sas: ata13: end_device-0:1:12: dev error handler
[ 32.886013] sas: ata14: end_device-0:1:13: dev error handler
[ 32.886014] sas: ata15: end_device-0:1:14: dev error handler
[ 32.886017] sas: ata16: end_device-0:1:15: dev error handler
[ 32.886019] sas: ata17: end_device-0:1:16: dev error handler
[ 32.886023] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.886335] sd 0:0:2:0: [sdd] command ffff8804068d0600 timed out
[ 32.886485] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.886487] sas: ata9: end_device-0:0:14: cmd error handler
[ 32.886495] sas: ata7: end_device-0:0:12: dev error handler
[ 32.886498] sas: ata8: end_device-0:0:13: dev error handler
[ 32.886501] sas: ata9: end_device-0:0:14: dev error handler
[ 32.886502] sas: ata10: end_device-0:0:15: dev error handler
[ 32.886505] sas: ata11: end_device-0:0:16: dev error handler
[ 32.886508] sas: ata12: end_device-0:0:17: dev error handler
[ 32.886509] sas: ata13: end_device-0:1:12: dev error handler
[ 32.886512] sas: ata14: end_device-0:1:13: dev error handler
[ 32.886512] sas: ata15: end_device-0:1:14: dev error handler
[ 32.886515] sas: ata16: end_device-0:1:15: dev error handler
[ 32.886516] sas: ata17: end_device-0:1:16: dev error handler
[ 32.886520] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.886883] sd 0:0:3:0: [sde] command ffff880404107500 timed out
[ 32.887002] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.887004] sas: ata10: end_device-0:0:15: cmd error handler
[ 32.887012] sas: ata7: end_device-0:0:12: dev error handler
[ 32.887019] sas: ata8: end_device-0:0:13: dev error handler
[ 32.887023] sas: ata9: end_device-0:0:14: dev error handler
[ 32.887026] sas: ata10: end_device-0:0:15: dev error handler
[ 32.887032] sas: ata11: end_device-0:0:16: dev error handler
[ 32.887035] sas: ata12: end_device-0:0:17: dev error handler
[ 32.887038] sas: ata13: end_device-0:1:12: dev error handler
[ 32.887040] sas: ata14: end_device-0:1:13: dev error handler
[ 32.887043] sas: ata15: end_device-0:1:14: dev error handler
[ 32.887045] sas: ata16: end_device-0:1:15: dev error handler
[ 32.887047] sas: ata17: end_device-0:1:16: dev error handler
[ 32.887072] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.888071] type=1400 audit(1409953734.556:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=630 comm="apparmor_parser"
[ 32.888076] type=1400 audit(1409953734.556:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=630 comm="apparmor_parser"
[ 32.888079] type=1400 audit(1409953734.556:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=630 comm="apparmor_parser"
[ 32.888201] type=1400 audit(1409953734.556:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=632 comm="apparmor_parser"
[ 32.888207] type=1400 audit(1409953734.556:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=632 comm="apparmor_parser"
[ 32.888211] type=1400 audit(1409953734.556:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=632 comm="apparmor_parser"
[ 32.888423] type=1400 audit(1409953734.556:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=630 comm="apparmor_parser"
[ 32.888428] type=1400 audit(1409953734.556:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=630 comm="apparmor_parser"
[ 32.888565] type=1400 audit(1409953734.556:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=632 comm="apparmor_parser"
[ 32.888570] type=1400 audit(1409953734.556:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=632 comm="apparmor_parser"
[ 32.890963] cfg80211: World regulatory domain updated:
[ 32.890965] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 32.890967] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.890968] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.890969] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 32.890970] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.890971] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.893664] [drm] Initialized drm 1.1.0 20060810
[ 32.894582] sd 0:0:0:0: [sdb] command ffff880409385200 timed out
[ 32.894591] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.894594] sas: ata7: end_device-0:0:12: cmd error handler
[ 32.894600] sas: ata7: end_device-0:0:12: dev error handler
[ 32.894612] sas: ata8: end_device-0:0:13: dev error handler
[ 32.894616] sas: ata9: end_device-0:0:14: dev error handler
[ 32.894620] sas: ata10: end_device-0:0:15: dev error handler
[ 32.894624] sas: ata11: end_device-0:0:16: dev error handler
[ 32.894627] sas: ata12: end_device-0:0:17: dev error handler
[ 32.894631] sas: ata13: end_device-0:1:12: dev error handler
[ 32.894635] sas: ata14: end_device-0:1:13: dev error handler
[ 32.894638] sas: ata15: end_device-0:1:14: dev error handler
[ 32.894642] sas: ata16: end_device-0:1:15: dev error handler
[ 32.894645] sas: ata17: end_device-0:1:16: dev error handler
[ 32.894651] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.900183] sd 0:0:9:0: [sdj] command ffff8804078c8400 timed out
[ 32.900192] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.900194] sas: ata15: end_device-0:1:14: cmd error handler
[ 32.900372] sas: ata7: end_device-0:0:12: dev error handler
[ 32.900375] sas: ata8: end_device-0:0:13: dev error handler
[ 32.900380] sas: ata9: end_device-0:0:14: dev error handler
[ 32.900381] sas: ata10: end_device-0:0:15: dev error handler
[ 32.900383] sas: ata11: end_device-0:0:16: dev error handler
[ 32.900384] sas: ata12: end_device-0:0:17: dev error handler
[ 32.900386] sas: ata13: end_device-0:1:12: dev error handler
[ 32.900388] sas: ata14: end_device-0:1:13: dev error handler
[ 32.900389] sas: ata15: end_device-0:1:14: dev error handler
[ 32.900392] sas: ata16: end_device-0:1:15: dev error handler
[ 32.900395] sas: ata17: end_device-0:1:16: dev error handler
[ 32.900400] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.900577] sd 0:0:8:0: [sdi] command ffff8800d9547000 timed out
[ 32.900706] sd 0:0:4:0: [sdf] command ffff8800364d6b00 timed out
[ 32.900869] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 32.900871] sas: ata14: end_device-0:1:13: cmd error handler
[ 32.900872] sas: ata11: end_device-0:0:16: cmd error handler
[ 32.900879] sas: ata7: end_device-0:0:12: dev error handler
[ 32.900884] sas: ata8: end_device-0:0:13: dev error handler
[ 32.900887] sas: ata9: end_device-0:0:14: dev error handler
[ 32.900890] sas: ata10: end_device-0:0:15: dev error handler
[ 32.900895] sas: ata11: end_device-0:0:16: dev error handler
[ 32.900898] sas: ata12: end_device-0:0:17: dev error handler
[ 32.900903] sas: ata13: end_device-0:1:12: dev error handler
[ 32.900904] sas: ata14: end_device-0:1:13: dev error handler
[ 32.900905] sas: ata15: end_device-0:1:14: dev error handler
[ 32.900908] sas: ata16: end_device-0:1:15: dev error handler
[ 32.900909] sas: ata17: end_device-0:1:16: dev error handler
[ 32.900915] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.901207] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 32.903842] sd 0:0:10:0: [sdk] command ffff880404efc500 timed out
[ 32.903850] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.903852] sas: ata16: end_device-0:1:15: cmd error handler
[ 32.903861] sas: ata7: end_device-0:0:12: dev error handler
[ 32.903870] sas: ata8: end_device-0:0:13: dev error handler
[ 32.903874] sas: ata9: end_device-0:0:14: dev error handler
[ 32.903878] sas: ata10: end_device-0:0:15: dev error handler
[ 32.903881] sas: ata11: end_device-0:0:16: dev error handler
[ 32.903885] sas: ata12: end_device-0:0:17: dev error handler
[ 32.903889] sas: ata13: end_device-0:1:12: dev error handler
[ 32.903892] sas: ata14: end_device-0:1:13: dev error handler
[ 32.903895] sas: ata15: end_device-0:1:14: dev error handler
[ 32.903899] sas: ata16: end_device-0:1:15: dev error handler
[ 32.903906] sas: ata17: end_device-0:1:16: dev error handler
[ 32.903912] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.936768] init: udev-fallback-graphics main process (742) terminated with status 1
[ 33.014661] e1000e 0000:00:19.0: irq 47 for MSI/MSI-X
[ 33.117298] e1000e 0000:00:19.0: irq 47 for MSI/MSI-X
[ 33.117409] IPv6: ADDRCONF(NETDEV_UP): em2: link is not ready
[ 33.134955] init: Failed to obtain startpar-bridge instance: Unknown parameter: INSTANCE
[ 33.590145] RAID conf printout:
[ 33.590149] --- level:6 rd:10 wd:10
[ 33.590151] disk 0, o:1, dev:sdb1
[ 33.590152] disk 1, o:1, dev:sdc1
[ 33.590152] disk 2, o:1, dev:sdd1
[ 33.590153] disk 3, o:1, dev:sde1
[ 33.590154] disk 4, o:1, dev:sdf1
[ 33.590155] disk 5, o:1, dev:sdg1
[ 33.590155] disk 6, o:1, dev:sdh1
[ 33.590156] disk 7, o:1, dev:sdi1
[ 33.590157] disk 8, o:1, dev:sdj1
[ 33.590158] disk 9, o:1, dev:sdk1
[ 33.725096] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: errors=continue
[ 33.740684] FS-Cache: Loaded
[ 33.744773] RPC: Registered named UNIX socket transport module.
[ 33.744775] RPC: Registered udp transport module.
[ 33.744775] RPC: Registered tcp transport module.
[ 33.744776] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 33.751333] FS-Cache: Netfs 'nfs' registered for caching
[ 33.757318] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 33.768107] init: failsafe main process (1041) killed by TERM signal
[ 34.050996] ipmi device interface
[ 34.186362] init: plymouth-upstart-bridge main process ended, respawning
[ 36.783537] e1000e: em2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 36.783567] IPv6: ADDRCONF(NETDEV_CHANGE): em2: link becomes ready
[ 130.814661] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.814661]
[ 130.814664] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.814666] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 130.814667] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=303 CI=302
[ 130.815159] pm80xx pm8001_mpi_msg_consume 1450:: CI=318 PI=319 msgHeader=8100200d
[ 130.815161] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.815162] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.815164] pm80xx pm8001_mpi_msg_free_set 1407: CI=319 PI=319
[ 130.815178] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.815178]
[ 130.815179] pm80xx pm80xx_chip_sata_req 4105:no data
[ 130.815180] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 130.815181] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=304 CI=303
[ 130.815273] pm80xx pm8001_mpi_msg_consume 1450:: CI=319 PI=320 msgHeader=8100200d
[ 130.815274] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.815275] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.815276] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 130.815287] pm80xx mpi_sata_completion 2090:other len = 20
[ 130.815288] pm80xx pm8001_mpi_msg_free_set 1407: CI=320 PI=320
[ 130.815298] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.815298]
[ 130.815298] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.815299] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 130.815300] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=305 CI=304
[ 130.815741] pm80xx pm8001_mpi_msg_consume 1450:: CI=320 PI=321 msgHeader=8100200d
[ 130.815742] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.815743] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.815755] pm80xx pm8001_mpi_msg_free_set 1407: CI=321 PI=321
[ 130.820126] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.820126]
[ 130.820127] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.820128] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.820129] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=306 CI=305
[ 130.823365] pm80xx pm8001_mpi_msg_consume 1450:: CI=321 PI=322 msgHeader=8100200d
[ 130.823369] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.823371] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.823381] pm80xx pm8001_mpi_msg_free_set 1407: CI=322 PI=322
[ 130.823442] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.823442]
[ 130.823445] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.823447] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.823449] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=307 CI=306
[ 130.826791] pm80xx pm8001_mpi_msg_consume 1450:: CI=322 PI=323 msgHeader=8100200d
[ 130.826794] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.826795] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.826799] pm80xx pm8001_mpi_msg_free_set 1407: CI=323 PI=323
[ 130.826830] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.826830]
[ 130.826831] pm80xx pm80xx_chip_sata_req 4105:no data
[ 130.826832] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.826833] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=308 CI=307
[ 130.869586] pm80xx pm8001_mpi_msg_consume 1450:: CI=323 PI=324 msgHeader=8100200d
[ 130.869588] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.869589] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.869590] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 130.869591] pm80xx mpi_sata_completion 2090:other len = 20
[ 130.869595] pm80xx pm8001_mpi_msg_free_set 1407: CI=324 PI=324
[ 130.869712] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.869712]
[ 130.869713] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.869714] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.869715] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=309 CI=308
[ 130.869936] pm80xx pm8001_mpi_msg_consume 1450:: CI=324 PI=325 msgHeader=8100200d
[ 130.869938] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.869939] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.869943] pm80xx pm8001_mpi_msg_free_set 1407: CI=325 PI=325
[ 130.869972] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.869972]
[ 130.869974] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.869975] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.869977] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=310 CI=309
[ 130.870276] pm80xx pm8001_mpi_msg_consume 1450:: CI=325 PI=326 msgHeader=8100200d
[ 130.870278] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.870279] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.870283] pm80xx pm8001_mpi_msg_free_set 1407: CI=326 PI=326
[ 130.870316] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.870316]
[ 130.870317] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.870318] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.870320] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=311 CI=310
[ 130.870623] pm80xx pm8001_mpi_msg_consume 1450:: CI=326 PI=327 msgHeader=8100200d
[ 130.870625] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.870626] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.870630] pm80xx pm8001_mpi_msg_free_set 1407: CI=327 PI=327
[ 130.870656] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.870656]
[ 130.870657] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.870658] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.870659] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=312 CI=311
[ 130.870923] pm80xx pm8001_mpi_msg_consume 1450:: CI=327 PI=328 msgHeader=8100200d
[ 130.870925] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.870926] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.870930] pm80xx pm8001_mpi_msg_free_set 1407: CI=328 PI=328
[ 132.070555] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.070555]
[ 132.070558] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.070559] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.070561] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=313 CI=312
[ 132.071042] pm80xx pm8001_mpi_msg_consume 1450:: CI=328 PI=329 msgHeader=8100200d
[ 132.071045] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.071046] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.071051] pm80xx pm8001_mpi_msg_free_set 1407: CI=329 PI=329
[ 132.071091] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.071091]
[ 132.071093] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.071094] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.071095] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=314 CI=313
[ 132.071162] pm80xx pm8001_mpi_msg_consume 1450:: CI=329 PI=330 msgHeader=8100200d
[ 132.071164] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.071165] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.071166] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.071167] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.071170] pm80xx pm8001_mpi_msg_free_set 1407: CI=330 PI=330
[ 132.071182] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.071182]
[ 132.071183] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.071184] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.071185] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=315 CI=314
[ 132.071639] pm80xx pm8001_mpi_msg_consume 1450:: CI=330 PI=331 msgHeader=8100200d
[ 132.071641] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.071642] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.071646] pm80xx pm8001_mpi_msg_free_set 1407: CI=331 PI=331
[ 132.075952] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.075952]
[ 132.075954] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.075955] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.075956] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=316 CI=315
[ 132.079180] pm80xx pm8001_mpi_msg_consume 1450:: CI=331 PI=332 msgHeader=8100200d
[ 132.079182] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.079183] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.079187] pm80xx pm8001_mpi_msg_free_set 1407: CI=332 PI=332
[ 132.079215] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.079215]
[ 132.079217] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.079218] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.079220] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=317 CI=316
[ 132.082638] pm80xx pm8001_mpi_msg_consume 1450:: CI=332 PI=333 msgHeader=8100200d
[ 132.082640] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.082641] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.082645] pm80xx pm8001_mpi_msg_free_set 1407: CI=333 PI=333
[ 132.089977] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.089977]
[ 132.089979] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.089980] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.089981] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=318 CI=317
[ 132.090467] pm80xx pm8001_mpi_msg_consume 1450:: CI=333 PI=334 msgHeader=8100200d
[ 132.090469] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.090470] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.090473] pm80xx pm8001_mpi_msg_free_set 1407: CI=334 PI=334
[ 132.090499] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.090499]
[ 132.090501] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.090502] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.090504] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=319 CI=318
[ 132.090570] pm80xx pm8001_mpi_msg_consume 1450:: CI=334 PI=335 msgHeader=8100200d
[ 132.090572] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.090573] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.090574] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.090574] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.090578] pm80xx pm8001_mpi_msg_free_set 1407: CI=335 PI=335
[ 132.090589] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.090589]
[ 132.090589] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.090590] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.090591] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=320 CI=319
[ 132.091037] pm80xx pm8001_mpi_msg_consume 1450:: CI=335 PI=336 msgHeader=8100200d
[ 132.091039] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.091040] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.091044] pm80xx pm8001_mpi_msg_free_set 1407: CI=336 PI=336
[ 132.095302] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.095302]
[ 132.095303] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.095304] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.095306] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=321 CI=320
[ 132.098440] pm80xx pm8001_mpi_msg_consume 1450:: CI=336 PI=337 msgHeader=8100200d
[ 132.098443] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.098444] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.098449] pm80xx pm8001_mpi_msg_free_set 1407: CI=337 PI=337
[ 132.098478] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.098478]
[ 132.098480] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.098482] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.098484] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=322 CI=321
[ 132.101844] pm80xx pm8001_mpi_msg_consume 1450:: CI=337 PI=338 msgHeader=8100200d
[ 132.101846] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.101847] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.101850] pm80xx pm8001_mpi_msg_free_set 1407: CI=338 PI=338
[ 132.109109] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.109109]
[ 132.109111] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.109112] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.109113] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=323 CI=322
[ 132.109593] pm80xx pm8001_mpi_msg_consume 1450:: CI=338 PI=339 msgHeader=8100200d
[ 132.109595] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.109596] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.109599] pm80xx pm8001_mpi_msg_free_set 1407: CI=339 PI=339
[ 132.109611] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.109611]
[ 132.109611] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.109612] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.109613] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=324 CI=323
[ 132.109684] pm80xx pm8001_mpi_msg_consume 1450:: CI=339 PI=340 msgHeader=8100200d
[ 132.109686] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.109687] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.109687] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.109688] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.109692] pm80xx pm8001_mpi_msg_free_set 1407: CI=340 PI=340
[ 132.109710] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.109710]
[ 132.109711] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.109711] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.109712] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=325 CI=324
[ 132.110143] pm80xx pm8001_mpi_msg_consume 1450:: CI=340 PI=341 msgHeader=8100200d
[ 132.110145] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.110146] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.110159] pm80xx pm8001_mpi_msg_free_set 1407: CI=341 PI=341
[ 132.114461] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.114461]
[ 132.114462] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.114463] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.114464] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=326 CI=325
[ 132.117636] pm80xx pm8001_mpi_msg_consume 1450:: CI=341 PI=342 msgHeader=8100200d
[ 132.117638] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.117639] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.117644] pm80xx pm8001_mpi_msg_free_set 1407: CI=342 PI=342
[ 132.117657] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.117657]
[ 132.117658] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.117659] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.117660] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=327 CI=326
[ 132.121034] pm80xx pm8001_mpi_msg_consume 1450:: CI=342 PI=343 msgHeader=8100200d
[ 132.121036] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.121037] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.121041] pm80xx pm8001_mpi_msg_free_set 1407: CI=343 PI=343
[ 132.128346] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.128346]
[ 132.128348] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.128349] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.128350] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=328 CI=327
[ 132.128822] pm80xx pm8001_mpi_msg_consume 1450:: CI=343 PI=344 msgHeader=8100200d
[ 132.128824] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.128825] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.128828] pm80xx pm8001_mpi_msg_free_set 1407: CI=344 PI=344
[ 132.128860] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.128860]
[ 132.128861] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.128862] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.128863] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=329 CI=328
[ 132.128946] pm80xx pm8001_mpi_msg_consume 1450:: CI=344 PI=345 msgHeader=8100200d
[ 132.128947] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.128948] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.128949] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.128950] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.128953] pm80xx pm8001_mpi_msg_free_set 1407: CI=345 PI=345
[ 132.128974] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.128974]
[ 132.128985] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.128986] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.128987] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=330 CI=329
[ 132.129469] pm80xx pm8001_mpi_msg_consume 1450:: CI=345 PI=346 msgHeader=8100200d
[ 132.129471] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.129472] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.129476] pm80xx pm8001_mpi_msg_free_set 1407: CI=346 PI=346
[ 132.133809] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.133809]
[ 132.133810] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.133811] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.133812] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=331 CI=330
[ 132.136997] pm80xx pm8001_mpi_msg_consume 1450:: CI=346 PI=347 msgHeader=8100200d
[ 132.136999] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.137000] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.137004] pm80xx pm8001_mpi_msg_free_set 1407: CI=347 PI=347
[ 132.137029] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.137029]
[ 132.137030] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.137031] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.137032] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=332 CI=331
[ 132.140465] pm80xx pm8001_mpi_msg_consume 1450:: CI=347 PI=348 msgHeader=8100200d
[ 132.140468] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.140470] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.140480] pm80xx pm8001_mpi_msg_free_set 1407: CI=348 PI=348
[ 132.148403] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.148403]
[ 132.148405] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.148406] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.148408] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=333 CI=332
[ 132.148892] pm80xx pm8001_mpi_msg_consume 1450:: CI=348 PI=349 msgHeader=8100200d
[ 132.148903] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.148904] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.148906] pm80xx pm8001_mpi_msg_free_set 1407: CI=349 PI=349
[ 132.148916] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.148916]
[ 132.148916] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.148917] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.148918] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=334 CI=333
[ 132.149014] pm80xx pm8001_mpi_msg_consume 1450:: CI=349 PI=350 msgHeader=8100200d
[ 132.149015] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.149016] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.149017] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.149028] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.149029] pm80xx pm8001_mpi_msg_free_set 1407: CI=350 PI=350
[ 132.149038] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.149038]
[ 132.149038] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.149039] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.149040] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=335 CI=334
[ 132.149483] pm80xx pm8001_mpi_msg_consume 1450:: CI=350 PI=351 msgHeader=8100200d
[ 132.149484] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.149485] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.149487] pm80xx pm8001_mpi_msg_free_set 1407: CI=351 PI=351
[ 132.153805] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.153805]
[ 132.153806] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.153808] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.153809] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=336 CI=335
[ 132.157043] pm80xx pm8001_mpi_msg_consume 1450:: CI=351 PI=352 msgHeader=8100200d
[ 132.157047] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.157048] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.157053] pm80xx pm8001_mpi_msg_free_set 1407: CI=352 PI=352
[ 132.157092] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.157092]
[ 132.157094] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.157096] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.157097] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=337 CI=336
[ 132.160472] pm80xx pm8001_mpi_msg_consume 1450:: CI=352 PI=353 msgHeader=8100200d
[ 132.160476] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.160477] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.160482] pm80xx pm8001_mpi_msg_free_set 1407: CI=353 PI=353
[ 132.168287] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.168287]
[ 132.168290] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.168291] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.168293] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=338 CI=337
[ 132.168758] pm80xx pm8001_mpi_msg_consume 1450:: CI=353 PI=354 msgHeader=8100200d
[ 132.168760] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.168761] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.168765] pm80xx pm8001_mpi_msg_free_set 1407: CI=354 PI=354
[ 132.168794] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.168794]
[ 132.168795] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.168796] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.168797] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=339 CI=338
[ 132.168869] pm80xx pm8001_mpi_msg_consume 1450:: CI=354 PI=355 msgHeader=8100200d
[ 132.168871] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.168872] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.168883] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.168884] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.168885] pm80xx pm8001_mpi_msg_free_set 1407: CI=355 PI=355
[ 132.168896] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.168896]
[ 132.168896] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.168897] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.168898] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=340 CI=339
[ 132.169335] pm80xx pm8001_mpi_msg_consume 1450:: CI=355 PI=356 msgHeader=8100200d
[ 132.169336] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.169337] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.169349] pm80xx pm8001_mpi_msg_free_set 1407: CI=356 PI=356
[ 132.173663] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.173663]
[ 132.173664] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.173665] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.173666] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=341 CI=340
[ 132.176832] pm80xx pm8001_mpi_msg_consume 1450:: CI=356 PI=357 msgHeader=8100200d
[ 132.176834] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.176835] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.176837] pm80xx pm8001_mpi_msg_free_set 1407: CI=357 PI=357
[ 132.176851] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.176851]
[ 132.176852] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.176853] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.176855] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=342 CI=341
[ 132.180212] pm80xx pm8001_mpi_msg_consume 1450:: CI=357 PI=358 msgHeader=8100200d
[ 132.180214] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.180215] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.180217] pm80xx pm8001_mpi_msg_free_set 1407: CI=358 PI=358
[ 132.187528] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.187528]
[ 132.187530] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.187531] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.187533] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=343 CI=342
[ 132.188016] pm80xx pm8001_mpi_msg_consume 1450:: CI=358 PI=359 msgHeader=8100200d
[ 132.188018] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.188019] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.188020] pm80xx pm8001_mpi_msg_free_set 1407: CI=359 PI=359
[ 132.188036] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.188036]
[ 132.188037] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.188038] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.188040] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=344 CI=343
[ 132.188122] pm80xx pm8001_mpi_msg_consume 1450:: CI=359 PI=360 msgHeader=8100200d
[ 132.188123] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.188124] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.188125] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.188136] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.188137] pm80xx pm8001_mpi_msg_free_set 1407: CI=360 PI=360
[ 132.188147] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.188147]
[ 132.188148] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.188149] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.188150] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=345 CI=344
[ 132.188583] pm80xx pm8001_mpi_msg_consume 1450:: CI=360 PI=361 msgHeader=8100200d
[ 132.188584] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.188585] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.188597] pm80xx pm8001_mpi_msg_free_set 1407: CI=361 PI=361
[ 132.192934] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.192934]
[ 132.192935] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.192936] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.192937] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=346 CI=345
[ 132.196116] pm80xx pm8001_mpi_msg_consume 1450:: CI=361 PI=362 msgHeader=8100200d
[ 132.196118] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.196120] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.196125] pm80xx pm8001_mpi_msg_free_set 1407: CI=362 PI=362
[ 132.196170] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.196170]
[ 132.196173] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.196174] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.196176] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=347 CI=346
[ 132.199506] pm80xx pm8001_mpi_msg_consume 1450:: CI=362 PI=363 msgHeader=8100200d
[ 132.199508] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.199509] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.199514] pm80xx pm8001_mpi_msg_free_set 1407: CI=363 PI=363
[ 132.207274] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.207274]
[ 132.207276] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.207277] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.207278] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=348 CI=347
[ 132.207743] pm80xx pm8001_mpi_msg_consume 1450:: CI=363 PI=364 msgHeader=8100200d
[ 132.207744] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.207744] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.207746] pm80xx pm8001_mpi_msg_free_set 1407: CI=364 PI=364
[ 132.207755] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.207755]
[ 132.207756] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.207757] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.207758] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=349 CI=348
[ 132.207814] pm80xx pm8001_mpi_msg_consume 1450:: CI=364 PI=365 msgHeader=8100200d
[ 132.207818] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.207821] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.207825] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.207828] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.207830] pm80xx pm8001_mpi_msg_free_set 1407: CI=365 PI=365
[ 132.207846] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.207846]
[ 132.207847] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.207849] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.207850] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=350 CI=349
[ 132.208342] pm80xx pm8001_mpi_msg_consume 1450:: CI=365 PI=366 msgHeader=8100200d
[ 132.208343] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.208344] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.208355] pm80xx pm8001_mpi_msg_free_set 1407: CI=366 PI=366
[ 132.212801] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.212801]
[ 132.212802] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.212803] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.212804] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=351 CI=350
[ 132.215950] pm80xx pm8001_mpi_msg_consume 1450:: CI=366 PI=367 msgHeader=8100200d
[ 132.215952] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.215963] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.215965] pm80xx pm8001_mpi_msg_free_set 1407: CI=367 PI=367
[ 132.215996] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.215996]
[ 132.215997] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.215999] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.216000] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=352 CI=351
[ 132.219333] pm80xx pm8001_mpi_msg_consume 1450:: CI=367 PI=368 msgHeader=8100200d
[ 132.219334] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.219336] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.219348] pm80xx pm8001_mpi_msg_free_set 1407: CI=368 PI=368
[ 132.226844] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.226844]
[ 132.226845] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.226847] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.226848] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=353 CI=352
[ 132.227328] pm80xx pm8001_mpi_msg_consume 1450:: CI=368 PI=369 msgHeader=8100200d
[ 132.227329] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.227340] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.227342] pm80xx pm8001_mpi_msg_free_set 1407: CI=369 PI=369
[ 132.227354] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.227354]
[ 132.227355] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.227355] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.227356] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=354 CI=353
[ 132.227410] pm80xx pm8001_mpi_msg_consume 1450:: CI=369 PI=370 msgHeader=8100200d
[ 132.227411] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.227412] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.227412] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.227413] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.227414] pm80xx pm8001_mpi_msg_free_set 1407: CI=370 PI=370
[ 132.227421] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.227421]
[ 132.227422] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.227422] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.227423] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=355 CI=354
[ 132.227858] pm80xx pm8001_mpi_msg_consume 1450:: CI=370 PI=371 msgHeader=8100200d
[ 132.227859] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.227860] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.227864] pm80xx pm8001_mpi_msg_free_set 1407: CI=371 PI=371
[ 132.232209] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.232209]
[ 132.232210] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.232211] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.232212] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=356 CI=355
[ 132.235376] pm80xx pm8001_mpi_msg_consume 1450:: CI=371 PI=372 msgHeader=8100200d
[ 132.235377] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.235388] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.235390] pm80xx pm8001_mpi_msg_free_set 1407: CI=372 PI=372
[ 132.235400] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.235400]
[ 132.235401] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.235402] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.235403] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=357 CI=356
[ 132.238731] pm80xx pm8001_mpi_msg_consume 1450:: CI=372 PI=373 msgHeader=8100200d
[ 132.238733] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.238734] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.238736] pm80xx pm8001_mpi_msg_free_set 1407: CI=373 PI=373
[ 132.246365] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.246365]
[ 132.246366] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.246367] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.246369] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=358 CI=357
[ 132.246833] pm80xx pm8001_mpi_msg_consume 1450:: CI=373 PI=374 msgHeader=8100200d
[ 132.246834] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.246835] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.246836] pm80xx pm8001_mpi_msg_free_set 1407: CI=374 PI=374
[ 132.246845] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.246845]
[ 132.246846] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.246846] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.246847] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=359 CI=358
[ 132.246938] pm80xx pm8001_mpi_msg_consume 1450:: CI=374 PI=375 msgHeader=8100200d
[ 132.246939] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.246940] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.246941] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.246951] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.246953] pm80xx pm8001_mpi_msg_free_set 1407: CI=375 PI=375
[ 132.246960] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.246960]
[ 132.246961] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.246962] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.246963] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=360 CI=359
[ 132.247392] pm80xx pm8001_mpi_msg_consume 1450:: CI=375 PI=376 msgHeader=8100200d
[ 132.247392] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.247393] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.247394] pm80xx pm8001_mpi_msg_free_set 1407: CI=376 PI=376
[ 132.251673] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.251673]
[ 132.251674] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.251675] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.251676] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=361 CI=360
[ 132.254843] pm80xx pm8001_mpi_msg_consume 1450:: CI=376 PI=377 msgHeader=8100200d
[ 132.254845] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.254846] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.254847] pm80xx pm8001_mpi_msg_free_set 1407: CI=377 PI=377
[ 132.254862] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.254862]
[ 132.254863] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.254864] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.254865] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=362 CI=361
[ 132.258254] pm80xx pm8001_mpi_msg_consume 1450:: CI=377 PI=378 msgHeader=8100200d
[ 132.258258] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.258260] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.258270] pm80xx pm8001_mpi_msg_free_set 1407: CI=378 PI=378
[ 132.266366] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.266366]
[ 132.266368] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.266370] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.266372] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=363 CI=362
[ 132.266857] pm80xx pm8001_mpi_msg_consume 1450:: CI=378 PI=379 msgHeader=8100200d
[ 132.266860] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.266861] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.266865] pm80xx pm8001_mpi_msg_free_set 1407: CI=379 PI=379
[ 132.266892] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.266892]
[ 132.266893] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.266894] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.266895] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=364 CI=363
[ 132.266963] pm80xx pm8001_mpi_msg_consume 1450:: CI=379 PI=380 msgHeader=8100200d
[ 132.266965] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.266966] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.266967] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.266968] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.266972] pm80xx pm8001_mpi_msg_free_set 1407: CI=380 PI=380
[ 132.266982] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.266982]
[ 132.266984] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.266987] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.266988] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=365 CI=364
[ 132.267438] pm80xx pm8001_mpi_msg_consume 1450:: CI=380 PI=381 msgHeader=8100200d
[ 132.267440] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.267440] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.267444] pm80xx pm8001_mpi_msg_free_set 1407: CI=381 PI=381
[ 132.271755] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.271755]
[ 132.271756] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.271757] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.271758] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=366 CI=365
[ 132.274567] pm80xx pm8001_mpi_msg_consume 1450:: CI=381 PI=382 msgHeader=8100200d
[ 132.274569] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.274570] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.274574] pm80xx pm8001_mpi_msg_free_set 1407: CI=382 PI=382
[ 132.274597] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.274597]
[ 132.274598] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.274599] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.274600] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=367 CI=366
[ 132.277588] pm80xx pm8001_mpi_msg_consume 1450:: CI=382 PI=383 msgHeader=8100200d
[ 132.277592] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.277593] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.277603] pm80xx pm8001_mpi_msg_free_set 1407: CI=383 PI=383
[ 132.923990] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.923990]
[ 132.923993] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.923994] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.923996] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=368 CI=367
[ 132.924492] pm80xx pm8001_mpi_msg_consume 1450:: CI=383 PI=384 msgHeader=8100200d
[ 132.924493] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.924494] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.924496] pm80xx pm8001_mpi_msg_free_set 1407: CI=384 PI=384
[ 132.924508] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.924508]
[ 132.924509] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.924510] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.924511] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=369 CI=368
[ 132.924607] pm80xx pm8001_mpi_msg_consume 1450:: CI=384 PI=385 msgHeader=8100200d
[ 132.924608] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.924609] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.924610] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.924621] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.924622] pm80xx pm8001_mpi_msg_free_set 1407: CI=385 PI=385
[ 132.924640] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.924640]
[ 132.924640] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.924641] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.924642] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=370 CI=369
[ 132.925089] pm80xx pm8001_mpi_msg_consume 1450:: CI=385 PI=386 msgHeader=8100200d
[ 132.925090] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.925091] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.925103] pm80xx pm8001_mpi_msg_free_set 1407: CI=386 PI=386
[ 132.929540] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.929540]
[ 132.929541] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.929543] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.929544] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=371 CI=370
[ 132.932357] pm80xx pm8001_mpi_msg_consume 1450:: CI=386 PI=387 msgHeader=8100200d
[ 132.932361] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.932363] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.932372] pm80xx pm8001_mpi_msg_free_set 1407: CI=387 PI=387
[ 132.932433] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.932433]
[ 132.932435] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.932437] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.932439] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=372 CI=371
[ 132.935459] pm80xx pm8001_mpi_msg_consume 1450:: CI=387 PI=388 msgHeader=8100200d
[ 132.935463] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.935464] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.935475] pm80xx pm8001_mpi_msg_free_set 1407: CI=388 PI=388
[ 132.935534] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.935534]
[ 132.935536] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.935538] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.935540] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=373 CI=372
[ 132.973020] pm80xx pm8001_mpi_msg_consume 1450:: CI=388 PI=389 msgHeader=8100200d
[ 132.973024] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.973026] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.973027] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.973028] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.973038] pm80xx pm8001_mpi_msg_free_set 1407: CI=389 PI=389
[ 132.973198] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.973198]
[ 132.973200] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.973202] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.973205] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=374 CI=373
[ 132.973437] pm80xx pm8001_mpi_msg_consume 1450:: CI=389 PI=390 msgHeader=8100200d
[ 132.973440] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.973441] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.973445] pm80xx pm8001_mpi_msg_free_set 1407: CI=390 PI=390
[ 132.973468] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.973468]
[ 132.973469] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.973470] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.973471] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=375 CI=374
[ 132.973777] pm80xx pm8001_mpi_msg_consume 1450:: CI=390 PI=391 msgHeader=8100200d
[ 132.973779] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.973780] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.973784] pm80xx pm8001_mpi_msg_free_set 1407: CI=391 PI=391
[ 132.973808] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.973808]
[ 132.973809] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.973810] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.973811] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=376 CI=375
[ 132.974122] pm80xx pm8001_mpi_msg_consume 1450:: CI=391 PI=392 msgHeader=8100200d
[ 132.974124] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.974125] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.974129] pm80xx pm8001_mpi_msg_free_set 1407: CI=392 PI=392
[ 132.974154] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.974154]
[ 132.974155] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.974155] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.974157] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=377 CI=376
[ 132.974424] pm80xx pm8001_mpi_msg_consume 1450:: CI=392 PI=393 msgHeader=8100200d
[ 132.974426] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.974427] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.974431] pm80xx pm8001_mpi_msg_free_set 1407: CI=393 PI=393
[ 160.998098] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 160.998098]
[ 160.998101] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 160.998103] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 160.998105] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=378 CI=377
[ 160.998602] pm80xx pm8001_mpi_msg_consume 1450:: CI=393 PI=394 msgHeader=8100200d
[ 160.998604] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 160.998606] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 160.998608] pm80xx pm8001_mpi_msg_free_set 1407: CI=394 PI=394
[ 160.998629] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 160.998629]
[ 160.998630] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 160.998631] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 160.998632] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=379 CI=378
[ 160.999079] pm80xx pm8001_mpi_msg_consume 1450:: CI=394 PI=395 msgHeader=8100200d
[ 160.999081] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 160.999082] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 160.999093] pm80xx pm8001_mpi_msg_free_set 1407: CI=395 PI=395
[ 161.004667] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.004667]
[ 161.004669] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.004670] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.004672] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=380 CI=379
[ 161.007874] pm80xx pm8001_mpi_msg_consume 1450:: CI=395 PI=396 msgHeader=8100200d
[ 161.007876] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.007877] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.007881] pm80xx pm8001_mpi_msg_free_set 1407: CI=396 PI=396
[ 161.007913] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.007913]
[ 161.007915] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.007917] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.007918] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=381 CI=380
[ 161.011308] pm80xx pm8001_mpi_msg_consume 1450:: CI=396 PI=397 msgHeader=8100200d
[ 161.011312] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.011314] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.011324] pm80xx pm8001_mpi_msg_free_set 1407: CI=397 PI=397
[ 161.011388] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.011388]
[ 161.011391] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.011393] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.011396] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=382 CI=381
[ 161.044962] pm80xx pm8001_mpi_msg_consume 1450:: CI=397 PI=398 msgHeader=8100200d
[ 161.044966] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.044968] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.044969] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.044969] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.044979] pm80xx pm8001_mpi_msg_free_set 1407: CI=398 PI=398
[ 161.045174] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.045174]
[ 161.045176] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.045178] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.045180] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=383 CI=382
[ 161.045407] pm80xx pm8001_mpi_msg_consume 1450:: CI=398 PI=399 msgHeader=8100200d
[ 161.045409] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.045410] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.045415] pm80xx pm8001_mpi_msg_free_set 1407: CI=399 PI=399
[ 161.045427] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.045427]
[ 161.045428] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.045429] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.045430] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=384 CI=383
[ 161.045727] pm80xx pm8001_mpi_msg_consume 1450:: CI=399 PI=400 msgHeader=8100200d
[ 161.045729] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.045730] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.045734] pm80xx pm8001_mpi_msg_free_set 1407: CI=400 PI=400
[ 161.045751] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.045751]
[ 161.045752] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.045752] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.045753] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=385 CI=384
[ 161.046057] pm80xx pm8001_mpi_msg_consume 1450:: CI=400 PI=401 msgHeader=8100200d
[ 161.046059] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.046060] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.046064] pm80xx pm8001_mpi_msg_free_set 1407: CI=401 PI=401
[ 161.046080] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.046080]
[ 161.046081] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.046082] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.046083] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=386 CI=385
[ 161.046354] pm80xx pm8001_mpi_msg_consume 1450:: CI=401 PI=402 msgHeader=8100200d
[ 161.046356] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.046357] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.046361] pm80xx pm8001_mpi_msg_free_set 1407: CI=402 PI=402
[ 161.057209] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.057209]
[ 161.057210] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.057212] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.057213] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=387 CI=386
[ 161.057689] pm80xx pm8001_mpi_msg_consume 1450:: CI=402 PI=403 msgHeader=8100200d
[ 161.057691] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.057692] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.057696] pm80xx pm8001_mpi_msg_free_set 1407: CI=403 PI=403
[ 161.057734] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.057734]
[ 161.057736] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.057737] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.057739] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=388 CI=387
[ 161.058223] pm80xx pm8001_mpi_msg_consume 1450:: CI=403 PI=404 msgHeader=8100200d
[ 161.058225] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.058226] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.058229] pm80xx pm8001_mpi_msg_free_set 1407: CI=404 PI=404
[ 161.062696] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.062696]
[ 161.062697] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.062698] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.062700] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=389 CI=388
[ 161.065954] pm80xx pm8001_mpi_msg_consume 1450:: CI=404 PI=405 msgHeader=8100200d
[ 161.065958] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.065960] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.065970] pm80xx pm8001_mpi_msg_free_set 1407: CI=405 PI=405
[ 161.066029] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.066029]
[ 161.066031] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.066033] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.066035] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=390 CI=389
[ 161.069478] pm80xx pm8001_mpi_msg_consume 1450:: CI=405 PI=406 msgHeader=8100200d
[ 161.069480] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.069481] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.069486] pm80xx pm8001_mpi_msg_free_set 1407: CI=406 PI=406
[ 161.069514] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.069514]
[ 161.069516] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.069517] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.069518] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=391 CI=390
[ 161.103042] pm80xx pm8001_mpi_msg_consume 1450:: CI=406 PI=407 msgHeader=8100200d
[ 161.103045] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.103047] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.103048] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.103049] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.103058] pm80xx pm8001_mpi_msg_free_set 1407: CI=407 PI=407
[ 161.103218] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.103218]
[ 161.103221] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.103223] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.103225] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=392 CI=391
[ 161.103484] pm80xx pm8001_mpi_msg_consume 1450:: CI=407 PI=408 msgHeader=8100200d
[ 161.103486] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.103487] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.103492] pm80xx pm8001_mpi_msg_free_set 1407: CI=408 PI=408
[ 161.103515] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.103515]
[ 161.103516] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.103517] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.103518] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=393 CI=392
[ 161.103847] pm80xx pm8001_mpi_msg_consume 1450:: CI=408 PI=409 msgHeader=8100200d
[ 161.103849] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.103850] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.103854] pm80xx pm8001_mpi_msg_free_set 1407: CI=409 PI=409
[ 161.103878] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.103878]
[ 161.103879] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.103880] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.103881] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=394 CI=393
[ 161.104220] pm80xx pm8001_mpi_msg_consume 1450:: CI=409 PI=410 msgHeader=8100200d
[ 161.104222] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.104223] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.104227] pm80xx pm8001_mpi_msg_free_set 1407: CI=410 PI=410
[ 161.104252] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.104252]
[ 161.104253] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.104254] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.104255] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=395 CI=394
[ 161.104522] pm80xx pm8001_mpi_msg_consume 1450:: CI=410 PI=411 msgHeader=8100200d
[ 161.104524] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.104525] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.104528] pm80xx pm8001_mpi_msg_free_set 1407: CI=411 PI=411
[ 161.115566] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.115566]
[ 161.115568] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.115569] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.115570] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=396 CI=395
[ 161.116052] pm80xx pm8001_mpi_msg_consume 1450:: CI=411 PI=412 msgHeader=8100200d
[ 161.116054] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.116055] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.116059] pm80xx pm8001_mpi_msg_free_set 1407: CI=412 PI=412
[ 161.116085] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.116085]
[ 161.116086] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.116087] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.116088] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=397 CI=396
[ 161.116527] pm80xx pm8001_mpi_msg_consume 1450:: CI=412 PI=413 msgHeader=8100200d
[ 161.116529] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.116530] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.116534] pm80xx pm8001_mpi_msg_free_set 1407: CI=413 PI=413
[ 161.120927] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.120927]
[ 161.120928] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.120930] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.120931] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=398 CI=397
[ 161.124188] pm80xx pm8001_mpi_msg_consume 1450:: CI=413 PI=414 msgHeader=8100200d
[ 161.124192] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.124194] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.124204] pm80xx pm8001_mpi_msg_free_set 1407: CI=414 PI=414
[ 161.124264] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.124264]
[ 161.124266] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.124268] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.124270] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=399 CI=398
[ 161.127739] pm80xx pm8001_mpi_msg_consume 1450:: CI=414 PI=415 msgHeader=8100200d
[ 161.127743] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.127745] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.127755] pm80xx pm8001_mpi_msg_free_set 1407: CI=415 PI=415
[ 161.127813] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.127813]
[ 161.127815] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.127817] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.127819] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=400 CI=399
[ 161.159683] pm80xx pm8001_mpi_msg_consume 1450:: CI=415 PI=416 msgHeader=8100200d
[ 161.159687] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.159688] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.159689] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.159690] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.159700] pm80xx pm8001_mpi_msg_free_set 1407: CI=416 PI=416
[ 161.159853] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.159853]
[ 161.159855] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.159857] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.159859] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=401 CI=400
[ 161.160110] pm80xx pm8001_mpi_msg_consume 1450:: CI=416 PI=417 msgHeader=8100200d
[ 161.160112] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.160113] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.160118] pm80xx pm8001_mpi_msg_free_set 1407: CI=417 PI=417
[ 161.160141] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.160141]
[ 161.160142] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.160143] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.160144] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=402 CI=401
[ 161.160469] pm80xx pm8001_mpi_msg_consume 1450:: CI=417 PI=418 msgHeader=8100200d
[ 161.160471] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.160472] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.160476] pm80xx pm8001_mpi_msg_free_set 1407: CI=418 PI=418
[ 161.160500] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.160500]
[ 161.160501] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.160502] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.160503] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=403 CI=402
[ 161.160826] pm80xx pm8001_mpi_msg_consume 1450:: CI=418 PI=419 msgHeader=8100200d
[ 161.160828] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.160829] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.160833] pm80xx pm8001_mpi_msg_free_set 1407: CI=419 PI=419
[ 161.160858] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.160858]
[ 161.160859] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.160859] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.160861] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=404 CI=403
[ 161.161126] pm80xx pm8001_mpi_msg_consume 1450:: CI=419 PI=420 msgHeader=8100200d
[ 161.161128] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.161129] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.161133] pm80xx pm8001_mpi_msg_free_set 1407: CI=420 PI=420
[ 161.172177] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.172177]
[ 161.172179] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.172180] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.172181] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=405 CI=404
[ 161.172669] pm80xx pm8001_mpi_msg_consume 1450:: CI=420 PI=421 msgHeader=8100200d
[ 161.172672] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.172673] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.172676] pm80xx pm8001_mpi_msg_free_set 1407: CI=421 PI=421
[ 161.172702] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.172702]
[ 161.172703] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.172704] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.172705] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=406 CI=405
[ 161.173195] pm80xx pm8001_mpi_msg_consume 1450:: CI=421 PI=422 msgHeader=8100200d
[ 161.173197] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.173198] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.173202] pm80xx pm8001_mpi_msg_free_set 1407: CI=422 PI=422
[ 161.177673] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.177673]
[ 161.177675] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.177676] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.177677] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=407 CI=406
[ 161.180516] pm80xx pm8001_mpi_msg_consume 1450:: CI=422 PI=423 msgHeader=8100200d
[ 161.180518] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.180519] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.180523] pm80xx pm8001_mpi_msg_free_set 1407: CI=423 PI=423
[ 161.180547] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.180547]
[ 161.180548] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.180548] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.180550] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=408 CI=407
[ 161.183595] pm80xx pm8001_mpi_msg_consume 1450:: CI=423 PI=424 msgHeader=8100200d
[ 161.183599] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.183601] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.183610] pm80xx pm8001_mpi_msg_free_set 1407: CI=424 PI=424
[ 161.183668] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.183668]
[ 161.183670] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.183672] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.183674] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=409 CI=408
[ 161.216565] pm80xx pm8001_mpi_msg_consume 1450:: CI=424 PI=425 msgHeader=8100200d
[ 161.216569] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.216570] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.216571] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.216572] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.216581] pm80xx pm8001_mpi_msg_free_set 1407: CI=425 PI=425
[ 161.216740] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.216740]
[ 161.216742] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.216744] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.216746] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=410 CI=409
[ 161.216979] pm80xx pm8001_mpi_msg_consume 1450:: CI=425 PI=426 msgHeader=8100200d
[ 161.216981] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.216981] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.216984] pm80xx pm8001_mpi_msg_free_set 1407: CI=426 PI=426
[ 161.216998] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.216998]
[ 161.216999] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.217000] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.217002] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=411 CI=410
[ 161.217298] pm80xx pm8001_mpi_msg_consume 1450:: CI=426 PI=427 msgHeader=8100200d
[ 161.217299] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.217300] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.217303] pm80xx pm8001_mpi_msg_free_set 1407: CI=427 PI=427
[ 161.217323] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.217323]
[ 161.217324] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.217327] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.217329] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=412 CI=411
[ 161.217627] pm80xx pm8001_mpi_msg_consume 1450:: CI=427 PI=428 msgHeader=8100200d
[ 161.217628] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.217629] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.217632] pm80xx pm8001_mpi_msg_free_set 1407: CI=428 PI=428
[ 161.217656] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.217656]
[ 161.217657] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.217659] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.217660] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=413 CI=412
[ 161.217925] pm80xx pm8001_mpi_msg_consume 1450:: CI=428 PI=429 msgHeader=8100200d
[ 161.217927] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.217928] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.217932] pm80xx pm8001_mpi_msg_free_set 1407: CI=429 PI=429
[ 161.239414] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.239414]
[ 161.239416] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.239418] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.239420] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=414 CI=413
[ 161.239912] pm80xx pm8001_mpi_msg_consume 1450:: CI=429 PI=430 msgHeader=8100200d
[ 161.239914] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.239915] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.239920] pm80xx pm8001_mpi_msg_free_set 1407: CI=430 PI=430
[ 161.239949] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.239949]
[ 161.239950] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.239951] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.239952] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=415 CI=414
[ 161.240408] pm80xx pm8001_mpi_msg_consume 1450:: CI=430 PI=431 msgHeader=8100200d
[ 161.240410] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.240411] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.240416] pm80xx pm8001_mpi_msg_free_set 1407: CI=431 PI=431
[ 161.245903] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.245903]
[ 161.245904] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.245906] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.245907] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=416 CI=415
[ 161.249113] pm80xx pm8001_mpi_msg_consume 1450:: CI=431 PI=432 msgHeader=8100200d
[ 161.249115] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.249116] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.249119] pm80xx pm8001_mpi_msg_free_set 1407: CI=432 PI=432
[ 161.249150] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.249150]
[ 161.249152] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.249153] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.249155] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=417 CI=416
[ 161.252549] pm80xx pm8001_mpi_msg_consume 1450:: CI=432 PI=433 msgHeader=8100200d
[ 161.252553] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.252555] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.252565] pm80xx pm8001_mpi_msg_free_set 1407: CI=433 PI=433
[ 161.252623] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.252623]
[ 161.252625] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.252627] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.252629] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=418 CI=417
[ 161.298074] pm80xx pm8001_mpi_msg_consume 1450:: CI=433 PI=434 msgHeader=8100200d
[ 161.298078] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.298080] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.298081] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.298082] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.298092] pm80xx pm8001_mpi_msg_free_set 1407: CI=434 PI=434
[ 161.298241] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.298241]
[ 161.298243] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.298245] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.298247] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=419 CI=418
[ 161.298472] pm80xx pm8001_mpi_msg_consume 1450:: CI=434 PI=435 msgHeader=8100200d
[ 161.298474] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.298476] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.298481] pm80xx pm8001_mpi_msg_free_set 1407: CI=435 PI=435
[ 161.298511] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.298511]
[ 161.298513] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.298514] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.298515] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=420 CI=419
[ 161.298812] pm80xx pm8001_mpi_msg_consume 1450:: CI=435 PI=436 msgHeader=8100200d
[ 161.298814] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.298815] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.298819] pm80xx pm8001_mpi_msg_free_set 1407: CI=436 PI=436
[ 161.298852] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.298852]
[ 161.298854] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.298855] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.298856] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=421 CI=420
[ 161.299161] pm80xx pm8001_mpi_msg_consume 1450:: CI=436 PI=437 msgHeader=8100200d
[ 161.299163] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.299164] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.299167] pm80xx pm8001_mpi_msg_free_set 1407: CI=437 PI=437
[ 161.299193] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.299193]
[ 161.299194] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.299195] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.299196] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=422 CI=421
[ 161.299468] pm80xx pm8001_mpi_msg_consume 1450:: CI=437 PI=438 msgHeader=8100200d
[ 161.299470] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.299471] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.299475] pm80xx pm8001_mpi_msg_free_set 1407: CI=438 PI=438
[ 161.317775] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.317775]
[ 161.317777] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.317779] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.317780] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=423 CI=422
[ 161.318274] pm80xx pm8001_mpi_msg_consume 1450:: CI=438 PI=439 msgHeader=8100200d
[ 161.318276] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.318277] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.318281] pm80xx pm8001_mpi_msg_free_set 1407: CI=439 PI=439
[ 161.318306] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.318306]
[ 161.318307] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.318308] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.318309] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=424 CI=423
[ 161.318768] pm80xx pm8001_mpi_msg_consume 1450:: CI=439 PI=440 msgHeader=8100200d
[ 161.318770] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.318771] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.318775] pm80xx pm8001_mpi_msg_free_set 1407: CI=440 PI=440
[ 161.323143] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.323143]
[ 161.323144] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.323146] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.323147] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=425 CI=424
[ 161.326343] pm80xx pm8001_mpi_msg_consume 1450:: CI=440 PI=441 msgHeader=8100200d
[ 161.326345] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.326346] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.326350] pm80xx pm8001_mpi_msg_free_set 1407: CI=441 PI=441
[ 161.326380] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.326380]
[ 161.326382] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.326383] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.326384] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=426 CI=425
[ 161.329752] pm80xx pm8001_mpi_msg_consume 1450:: CI=441 PI=442 msgHeader=8100200d
[ 161.329755] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.329757] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.329768] pm80xx pm8001_mpi_msg_free_set 1407: CI=442 PI=442
[ 161.329825] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.329825]
[ 161.329828] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.329830] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.329831] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=427 CI=426
[ 161.369174] pm80xx pm8001_mpi_msg_consume 1450:: CI=442 PI=443 msgHeader=8100200d
[ 161.369177] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.369179] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.369180] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.369181] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.369191] pm80xx pm8001_mpi_msg_free_set 1407: CI=443 PI=443
[ 161.369345] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.369345]
[ 161.369347] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.369349] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.369351] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=428 CI=427
[ 161.369576] pm80xx pm8001_mpi_msg_consume 1450:: CI=443 PI=444 msgHeader=8100200d
[ 161.369578] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.369579] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.369584] pm80xx pm8001_mpi_msg_free_set 1407: CI=444 PI=444
[ 161.369614] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.369614]
[ 161.369616] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.369617] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.369618] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=429 CI=428
[ 161.369916] pm80xx pm8001_mpi_msg_consume 1450:: CI=444 PI=445 msgHeader=8100200d
[ 161.369918] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.369919] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.369922] pm80xx pm8001_mpi_msg_free_set 1407: CI=445 PI=445
[ 161.369955] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.369955]
[ 161.369957] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.369958] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.369959] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=430 CI=429
[ 161.370262] pm80xx pm8001_mpi_msg_consume 1450:: CI=445 PI=446 msgHeader=8100200d
[ 161.370264] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.370265] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.370268] pm80xx pm8001_mpi_msg_free_set 1407: CI=446 PI=446
[ 161.370295] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.370295]
[ 161.370296] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.370297] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.370298] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=431 CI=430
[ 161.370567] pm80xx pm8001_mpi_msg_consume 1450:: CI=446 PI=447 msgHeader=8100200d
[ 161.370569] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.370570] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.370574] pm80xx pm8001_mpi_msg_free_set 1407: CI=447 PI=447
[ 161.384493] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.384493]
[ 161.384495] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.384497] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.384500] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=432 CI=431
[ 161.400157] pm80xx pm8001_mpi_msg_consume 1450:: CI=447 PI=448 msgHeader=8100200d
[ 161.400160] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.400162] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.400172] pm80xx pm8001_mpi_msg_free_set 1407: CI=448 PI=448
[ 161.400236] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.400236]
[ 161.400239] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.400241] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.400243] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=433 CI=432
[ 161.400704] pm80xx pm8001_mpi_msg_consume 1450:: CI=448 PI=449 msgHeader=8100200d
[ 161.400706] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.400707] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.400712] pm80xx pm8001_mpi_msg_free_set 1407: CI=449 PI=449
[ 161.405212] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.405212]
[ 161.405213] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.405214] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.405225] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=434 CI=433
[ 161.408458] pm80xx pm8001_mpi_msg_consume 1450:: CI=449 PI=450 msgHeader=8100200d
[ 161.408462] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.408464] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.408473] pm80xx pm8001_mpi_msg_free_set 1407: CI=450 PI=450
[ 161.408532] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.408532]
[ 161.408535] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.408537] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.408539] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=435 CI=434
[ 161.411968] pm80xx pm8001_mpi_msg_consume 1450:: CI=450 PI=451 msgHeader=8100200d
[ 161.411972] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.411974] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.411984] pm80xx pm8001_mpi_msg_free_set 1407: CI=451 PI=451
[ 161.412041] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.412041]
[ 161.412044] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.412045] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.412047] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=436 CI=435
[ 161.438088] pm80xx pm8001_mpi_msg_consume 1450:: CI=451 PI=452 msgHeader=8100200d
[ 161.438091] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.438093] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.438094] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.438095] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.438104] pm80xx pm8001_mpi_msg_free_set 1407: CI=452 PI=452
[ 161.438257] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.438257]
[ 161.438259] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.438261] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.438263] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=437 CI=436
[ 161.438479] pm80xx pm8001_mpi_msg_consume 1450:: CI=452 PI=453 msgHeader=8100200d
[ 161.438481] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.438482] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.438487] pm80xx pm8001_mpi_msg_free_set 1407: CI=453 PI=453
[ 161.438517] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.438517]
[ 161.438519] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.438520] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.438521] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=438 CI=437
[ 161.438811] pm80xx pm8001_mpi_msg_consume 1450:: CI=453 PI=454 msgHeader=8100200d
[ 161.438813] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.438814] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.438817] pm80xx pm8001_mpi_msg_free_set 1407: CI=454 PI=454
[ 161.438844] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.438844]
[ 161.438845] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.438845] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.438847] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=439 CI=438
[ 161.439146] pm80xx pm8001_mpi_msg_consume 1450:: CI=454 PI=455 msgHeader=8100200d
[ 161.439148] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.439149] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.439153] pm80xx pm8001_mpi_msg_free_set 1407: CI=455 PI=455
[ 161.439178] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.439178]
[ 161.439179] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.439180] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.439181] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=440 CI=439
[ 161.439446] pm80xx pm8001_mpi_msg_consume 1450:: CI=455 PI=456 msgHeader=8100200d
[ 161.439448] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.439449] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.439453] pm80xx pm8001_mpi_msg_free_set 1407: CI=456 PI=456
[ 161.451185] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.451185]
[ 161.451187] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.451189] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.451191] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=441 CI=440
[ 161.451678] pm80xx pm8001_mpi_msg_consume 1450:: CI=456 PI=457 msgHeader=8100200d
[ 161.451681] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.451682] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.451687] pm80xx pm8001_mpi_msg_free_set 1407: CI=457 PI=457
[ 161.451719] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.451719]
[ 161.451721] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.451722] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.451724] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=442 CI=441
[ 161.452171] pm80xx pm8001_mpi_msg_consume 1450:: CI=457 PI=458 msgHeader=8100200d
[ 161.452174] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.452175] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.452180] pm80xx pm8001_mpi_msg_free_set 1407: CI=458 PI=458
[ 161.458700] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.458700]
[ 161.458702] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.458704] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.458706] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=443 CI=442
[ 161.461943] pm80xx pm8001_mpi_msg_consume 1450:: CI=458 PI=459 msgHeader=8100200d
[ 161.461947] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.461949] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.461959] pm80xx pm8001_mpi_msg_free_set 1407: CI=459 PI=459
[ 161.462018] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.462018]
[ 161.462020] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.462022] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.462025] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=444 CI=443
[ 161.465452] pm80xx pm8001_mpi_msg_consume 1450:: CI=459 PI=460 msgHeader=8100200d
[ 161.465455] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.465457] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.465467] pm80xx pm8001_mpi_msg_free_set 1407: CI=460 PI=460
[ 161.465525] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.465525]
[ 161.465528] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.465530] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.465532] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=445 CI=444
[ 161.492697] pm80xx pm8001_mpi_msg_consume 1450:: CI=460 PI=461 msgHeader=8100200d
[ 161.492700] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.492702] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.492703] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.492704] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.492713] pm80xx pm8001_mpi_msg_free_set 1407: CI=461 PI=461
[ 161.492877] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.492877]
[ 161.492879] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.492881] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.492883] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=446 CI=445
[ 161.493105] pm80xx pm8001_mpi_msg_consume 1450:: CI=461 PI=462 msgHeader=8100200d
[ 161.493107] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.493108] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.493113] pm80xx pm8001_mpi_msg_free_set 1407: CI=462 PI=462
[ 161.493143] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.493143]
[ 161.493145] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.493147] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.493148] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=447 CI=446
[ 161.493442] pm80xx pm8001_mpi_msg_consume 1450:: CI=462 PI=463 msgHeader=8100200d
[ 161.493444] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.493445] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.493449] pm80xx pm8001_mpi_msg_free_set 1407: CI=463 PI=463
[ 161.493482] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.493482]
[ 161.493483] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.493485] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.493486] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=448 CI=447
[ 161.493786] pm80xx pm8001_mpi_msg_consume 1450:: CI=463 PI=464 msgHeader=8100200d
[ 161.493788] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.493789] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.493793] pm80xx pm8001_mpi_msg_free_set 1407: CI=464 PI=464
[ 161.493828] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.493828]
[ 161.493829] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.493831] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.493832] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=449 CI=448
[ 161.494095] pm80xx pm8001_mpi_msg_consume 1450:: CI=464 PI=465 msgHeader=8100200d
[ 161.494097] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.494098] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.494102] pm80xx pm8001_mpi_msg_free_set 1407: CI=465 PI=465
[ 161.512006] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.512006]
[ 161.512008] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.512010] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.512012] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=450 CI=449
[ 161.512498] pm80xx pm8001_mpi_msg_consume 1450:: CI=465 PI=466 msgHeader=8100200d
[ 161.512501] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.512502] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.512507] pm80xx pm8001_mpi_msg_free_set 1407: CI=466 PI=466
[ 161.512536] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.512536]
[ 161.512537] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.512538] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.512539] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=451 CI=450
[ 161.512985] pm80xx pm8001_mpi_msg_consume 1450:: CI=466 PI=467 msgHeader=8100200d
[ 161.512988] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.512989] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.512993] pm80xx pm8001_mpi_msg_free_set 1407: CI=467 PI=467
[ 161.518572] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.518572]
[ 161.518574] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.518576] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.518577] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=452 CI=451
[ 161.521838] pm80xx pm8001_mpi_msg_consume 1450:: CI=467 PI=468 msgHeader=8100200d
[ 161.521839] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.521840] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.521844] pm80xx pm8001_mpi_msg_free_set 1407: CI=468 PI=468
[ 161.521875] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.521875]
[ 161.521876] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.521878] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.521879] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=453 CI=452
[ 161.525293] pm80xx pm8001_mpi_msg_consume 1450:: CI=468 PI=469 msgHeader=8100200d
[ 161.525295] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.525296] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.525300] pm80xx pm8001_mpi_msg_free_set 1407: CI=469 PI=469
[ 161.525330] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.525330]
[ 161.525332] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.525333] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.525334] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=454 CI=453
[ 161.558095] pm80xx pm8001_mpi_msg_consume 1450:: CI=469 PI=470 msgHeader=8100200d
[ 161.558099] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.558101] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.558101] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.558102] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.558112] pm80xx pm8001_mpi_msg_free_set 1407: CI=470 PI=470
[ 161.558265] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.558265]
[ 161.558268] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.558270] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.558272] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=455 CI=454
[ 161.558493] pm80xx pm8001_mpi_msg_consume 1450:: CI=470 PI=471 msgHeader=8100200d
[ 161.558495] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.558496] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.558501] pm80xx pm8001_mpi_msg_free_set 1407: CI=471 PI=471
[ 161.558524] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.558524]
[ 161.558525] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.558526] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.558527] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=456 CI=455
[ 161.558824] pm80xx pm8001_mpi_msg_consume 1450:: CI=471 PI=472 msgHeader=8100200d
[ 161.558826] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.558827] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.558831] pm80xx pm8001_mpi_msg_free_set 1407: CI=472 PI=472
[ 161.558855] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.558855]
[ 161.558856] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.558857] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.558858] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=457 CI=456
[ 161.559158] pm80xx pm8001_mpi_msg_consume 1450:: CI=472 PI=473 msgHeader=8100200d
[ 161.559160] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.559161] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.559165] pm80xx pm8001_mpi_msg_free_set 1407: CI=473 PI=473
[ 161.559190] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.559190]
[ 161.559191] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.559192] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.559193] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=458 CI=457
[ 161.559455] pm80xx pm8001_mpi_msg_consume 1450:: CI=473 PI=474 msgHeader=8100200d
[ 161.559457] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.559458] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.559462] pm80xx pm8001_mpi_msg_free_set 1407: CI=474 PI=474
[ 161.571447] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.571447]
[ 161.571450] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.571452] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.571454] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=459 CI=458
[ 161.571928] pm80xx pm8001_mpi_msg_consume 1450:: CI=474 PI=475 msgHeader=8100200d
[ 161.571931] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.571933] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.571938] pm80xx pm8001_mpi_msg_free_set 1407: CI=475 PI=475
[ 161.571968] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.571968]
[ 161.571970] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.571971] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.571972] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=460 CI=459
[ 161.572426] pm80xx pm8001_mpi_msg_consume 1450:: CI=475 PI=476 msgHeader=8100200d
[ 161.572428] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.572430] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.572435] pm80xx pm8001_mpi_msg_free_set 1407: CI=476 PI=476
[ 161.578928] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.578928]
[ 161.578930] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.578932] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.578934] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=461 CI=460
[ 161.582154] pm80xx pm8001_mpi_msg_consume 1450:: CI=476 PI=477 msgHeader=8100200d
[ 161.582156] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.582157] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.582161] pm80xx pm8001_mpi_msg_free_set 1407: CI=477 PI=477
[ 161.582192] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.582192]
[ 161.582193] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.582195] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.582196] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=462 CI=461
[ 161.585553] pm80xx pm8001_mpi_msg_consume 1450:: CI=477 PI=478 msgHeader=8100200d
[ 161.585557] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.585559] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.585569] pm80xx pm8001_mpi_msg_free_set 1407: CI=478 PI=478
[ 161.585627] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.585627]
[ 161.585630] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.585632] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.585634] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=463 CI=462
[ 161.614523] pm80xx pm8001_mpi_msg_consume 1450:: CI=478 PI=479 msgHeader=8100200d
[ 161.614526] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.614528] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.614529] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.614530] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.614539] pm80xx pm8001_mpi_msg_free_set 1407: CI=479 PI=479
[ 161.614688] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.614688]
[ 161.614690] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.614692] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.614694] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=464 CI=463
[ 161.614910] pm80xx pm8001_mpi_msg_consume 1450:: CI=479 PI=480 msgHeader=8100200d
[ 161.614913] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.614914] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.614919] pm80xx pm8001_mpi_msg_free_set 1407: CI=480 PI=480
[ 161.614942] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.614942]
[ 161.614943] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.614943] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.614945] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=465 CI=464
[ 161.615234] pm80xx pm8001_mpi_msg_consume 1450:: CI=480 PI=481 msgHeader=8100200d
[ 161.615236] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.615237] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.615241] pm80xx pm8001_mpi_msg_free_set 1407: CI=481 PI=481
[ 161.615265] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.615265]
[ 161.615265] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.615266] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.615267] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=466 CI=465
[ 161.615565] pm80xx pm8001_mpi_msg_consume 1450:: CI=481 PI=482 msgHeader=8100200d
[ 161.615567] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.615568] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.615572] pm80xx pm8001_mpi_msg_free_set 1407: CI=482 PI=482
[ 161.615597] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.615597]
[ 161.615598] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.615599] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.615600] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=467 CI=466
[ 161.615862] pm80xx pm8001_mpi_msg_consume 1450:: CI=482 PI=483 msgHeader=8100200d
[ 161.615864] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.615865] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.615869] pm80xx pm8001_mpi_msg_free_set 1407: CI=483 PI=483
[ 161.626929] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.626929]
[ 161.626930] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.626932] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.626933] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=468 CI=467
[ 161.627419] pm80xx pm8001_mpi_msg_consume 1450:: CI=483 PI=484 msgHeader=8100200d
[ 161.627420] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.627421] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.627425] pm80xx pm8001_mpi_msg_free_set 1407: CI=484 PI=484
[ 161.627459] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.627459]
[ 161.627460] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.627460] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.627462] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=469 CI=468
[ 161.627902] pm80xx pm8001_mpi_msg_consume 1450:: CI=484 PI=485 msgHeader=8100200d
[ 161.627904] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.627905] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.627908] pm80xx pm8001_mpi_msg_free_set 1407: CI=485 PI=485
[ 161.633926] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.633926]
[ 161.633928] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.633930] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.633932] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=470 CI=469
[ 161.637110] pm80xx pm8001_mpi_msg_consume 1450:: CI=485 PI=486 msgHeader=8100200d
[ 161.637113] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.637114] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.637119] pm80xx pm8001_mpi_msg_free_set 1407: CI=486 PI=486
[ 161.637155] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.637155]
[ 161.637157] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.637159] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.637161] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=471 CI=470
[ 161.640511] pm80xx pm8001_mpi_msg_consume 1450:: CI=486 PI=487 msgHeader=8100200d
[ 161.640514] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.640515] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.640520] pm80xx pm8001_mpi_msg_free_set 1407: CI=487 PI=487
[ 161.640548] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.640548]
[ 161.640550] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.640551] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.640552] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=472 CI=471
[ 161.687008] pm80xx pm8001_mpi_msg_consume 1450:: CI=487 PI=488 msgHeader=8100200d
[ 161.687011] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.687013] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.687014] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.687015] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.687024] pm80xx pm8001_mpi_msg_free_set 1407: CI=488 PI=488
[ 161.687179] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.687179]
[ 161.687182] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.687184] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.687186] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=473 CI=472
[ 161.687408] pm80xx pm8001_mpi_msg_consume 1450:: CI=488 PI=489 msgHeader=8100200d
[ 161.687411] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.687412] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.687416] pm80xx pm8001_mpi_msg_free_set 1407: CI=489 PI=489
[ 161.687440] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.687440]
[ 161.687441] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.687442] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.687445] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=474 CI=473
[ 161.687741] pm80xx pm8001_mpi_msg_consume 1450:: CI=489 PI=490 msgHeader=8100200d
[ 161.687743] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.687744] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.687748] pm80xx pm8001_mpi_msg_free_set 1407: CI=490 PI=490
[ 161.687772] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.687772]
[ 161.687773] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.687774] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.687775] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=475 CI=474
[ 161.688078] pm80xx pm8001_mpi_msg_consume 1450:: CI=490 PI=491 msgHeader=8100200d
[ 161.688080] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.688081] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.688085] pm80xx pm8001_mpi_msg_free_set 1407: CI=491 PI=491
[ 161.688110] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.688110]
[ 161.688111] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.688112] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.688113] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=476 CI=475
[ 161.688378] pm80xx pm8001_mpi_msg_consume 1450:: CI=491 PI=492 msgHeader=8100200d
[ 161.688380] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.688380] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.688384] pm80xx pm8001_mpi_msg_free_set 1407: CI=492 PI=492
[ 190.814105] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814105]
[ 190.814113] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814119] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814125] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=477 CI=476
[ 190.814137] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814137]
[ 190.814140] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814143] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814147] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=478 CI=476
[ 190.814158] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814158]
[ 190.814160] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814164] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814167] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=479 CI=476
[ 190.814177] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814177]
[ 190.814180] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814183] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814186] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=480 CI=476
[ 190.814196] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814196]
[ 190.814198] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814201] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814205] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=481 CI=476
[ 190.814214] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814214]
[ 190.814216] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814219] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814223] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=482 CI=476
[ 190.814232] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814232]
[ 190.814235] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814238] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814241] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=483 CI=476
[ 190.814251] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814251]
[ 190.814253] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814256] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814260] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=484 CI=476
[ 190.814270] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814270]
[ 190.814273] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814276] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814279] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=485 CI=476
[ 190.814289] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814289]
[ 190.814292] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814295] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814298] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=486 CI=476
[ 220.969757] sd 0:0:9:0: [sdj] command ffff880407bf5c00 timed out
[ 220.969777] sd 0:0:10:0: [sdk] command ffff880407bf4d00 timed out
[ 220.969784] sd 0:0:0:0: [sdb] command ffff880407bf5d00 timed out
[ 220.969788] sd 0:0:4:0: [sdf] command ffff880407bf4100 timed out
[ 220.969793] sd 0:0:3:0: [sde] command ffff880407bf4400 timed out
[ 220.969798] sd 0:0:1:0: [sdc] command ffff880407bf5700 timed out
[ 220.969803] sd 0:0:7:0: [sdh] command ffff880407bf5200 timed out
[ 220.969808] sd 0:0:8:0: [sdi] command ffff880407bf5e00 timed out
[ 220.969812] sd 0:0:2:0: [sdd] command ffff880407bf4f00 timed out
[ 220.969829] sd 0:0:5:0: [sdg] command ffff880407bf4c00 timed out
[ 220.969867] sas: Enter sas_scsi_recover_host busy: 10 failed: 10
[ 220.969882] sas: trying to find task 0xffff880035cdd680
[ 220.969888] sas: sas_scsi_find_task: aborting task 0xffff880035cdd680
[ 220.969900] pm80xx pm8001_chip_abort_task 4718:cmd_tag = e, abort task tag = 0x3
[ 220.969913] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:18 , UPDATED PI=487 CI=476
[ 240.972521] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 240.972532] pm80xx pm8001_abort_task 1245:rc= 5
[ 240.972538] sas: sas_scsi_find_task: querying task 0xffff880035cdd680
[ 240.972541] pm80xx pm8001_query_task 1168::rc= 5
[ 240.972544] sas: sas_scsi_find_task: task 0xffff880035cdd680 failed to abort
[ 240.972547] sas: task 0xffff880035cdd680 is not at LU: I_T recover
[ 240.972551] sas: I_T nexus reset for dev 50030480010f712e
[ 240.972566] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 240.972566]
[ 240.972573] pm80xx pm80xx_chip_smp_req 3806:SMP Frame Length 44
[ 240.972576] pm80xx pm80xx_chip_smp_req 3819:SMP REQUEST INDIRECT MODE
[ 240.972581] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:12 , UPDATED PI=488 CI=476
[ 250.977650] sas: smp task timed out or aborted
[ 250.977669] pm80xx pm8001_chip_abort_task 4718:cmd_tag = 10, abort task tag = 0xf
[ 250.977676] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:14 , UPDATED PI=489 CI=476
[ 271.022264] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 271.022270] pm80xx pm8001_abort_task 1245:rc= 5
[ 271.022272] sas: SMP task aborted and not done
[ 273.024354] pm80xx pm8001_chip_abort_task 4718:cmd_tag = 11, abort task tag = 0x0
[ 273.024363] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:18 , UPDATED PI=490 CI=476
[ 293.080977] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 293.080992] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:2a , UPDATED PI=491 CI=476
[ 361.606803] INFO: task sync:2812 blocked for more than 120 seconds.
[ 361.613171] Not tainted 3.13.0-35-generic #62-Ubuntu
[ 361.618727] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 361.626628] sync D ffff88041fcd4440 0 2812 2328 0x00000000
[ 361.626637] ffff880403fd7d50 0000000000000086 ffff880408601800 ffff880403fd7fd8
[ 361.626645] 0000000000014440 0000000000014440 ffff880408601800 ffff880403fd7e78
[ 361.626651] ffff880403fd7e80 7fffffffffffffff ffff880408601800 ffffffff811ecf30
[ 361.626658] Call Trace:
[ 361.626688] [<ffffffff811ecf30>] ? do_fsync+0x80/0x80
[ 361.626702] [<ffffffff81722749>] schedule+0x29/0x70
[ 361.626709] [<ffffffff81721999>] schedule_timeout+0x239/0x2d0
[ 361.626715] [<ffffffff811ecf30>] ? do_fsync+0x80/0x80
[ 361.626725] [<ffffffff815a4bc5>] ? md_make_request+0xd5/0x220
[ 361.626739] [<ffffffff811ecf30>] ? do_fsync+0x80/0x80
[ 361.626748] [<ffffffff815b9837>] ? dm_request+0x107/0x1a0
[ 361.626759] [<ffffffff811ecf30>] ? do_fsync+0x80/0x80
[ 361.626766] [<ffffffff81723266>] wait_for_completion+0xa6/0x160
[ 361.626777] [<ffffffff8109a8d0>] ? wake_up_state+0x20/0x20
[ 361.626783] [<ffffffff811f356e>] submit_bio_wait+0x5e/0x70
[ 361.626791] [<ffffffff8133bb7a>] blkdev_issue_flush+0x5a/0x90
[ 361.626812] [<ffffffff81255da9>] ext4_sync_fs+0xd9/0x130
[ 361.626821] [<ffffffff811ecf50>] sync_fs_one_sb+0x20/0x30
[ 361.626831] [<ffffffff811c0a62>] iterate_supers+0xb2/0x110
[ 361.626842] [<ffffffff811ed055>] sys_sync+0x55/0x90
[ 361.626849] [<ffffffff8172ed6d>] system_call_fastpath+0x1a/0x1f
^ permalink raw reply [flat|nested] 6+ messages in thread
* Fwd: Adaptec 71605H HBA randomly failing to detect any drives at init
2014-09-05 22:13 ` Andrew Robertson
@ 2014-09-06 5:32 ` Andrew Robertson
2015-05-18 19:19 ` Andrew Robertson
1 sibling, 0 replies; 6+ messages in thread
From: Andrew Robertson @ 2014-09-06 5:32 UTC (permalink / raw)
To: linux-scsi
[-- Attachment #1: Type: text/plain, Size: 12121 bytes --]
More info, as requested:
There are 2 sas expander chips in the system (LSI SAS2X28 & SAS2X36),
and there's a connection to each of them from the 71605H via a
separate 0.8m Adaptec cable. (Adaptec 2280200-R). This is a
Supermicro chassis.
Firmware version:
# cat /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/host0/scsi_host/host0/fw_version
02.08.60.01
I don't have immediate physical access to the box, so I'm not able to
do the hotplug logging test. However, I did "reset" the PCI device
via /sys, as shown below, and captured the logs from that (uploaded to
pastebin - see below)
With the latest kernel, v3.17-rc3, I got a kernel "null pointer
dereference" in the pm80xx module (dmesg output pasted in below).
I will also try replacing the cables with 0.5m adaptec cables as
suggested to see if that helps.
---
Reset test:
# find /sys -iname logging_level
/sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/host0/scsi_host/host0/logging_level
# echo 0xfff > /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/host0/scsi_host/host0/logging_level
# echo 1 > /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/rescan
# echo 1 > /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/reset
# sync
(at which point the process hung; in the dmesg you can see a "sync
blocked for more than 120 seconds")
Dmesg output: http://pastebin.com/Uak4Q4Gy
The disk/expander layout looks like:
[0:0:0:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdb /dev/sg1
[0:0:1:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdc /dev/sg2
[0:0:2:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdd /dev/sg3
[0:0:3:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sde /dev/sg4
[0:0:4:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdf /dev/sg5
[0:0:5:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdg /dev/sg6
[0:0:6:0] enclosu LSI SAS2X36 0e12 - /dev/sg7
[0:0:7:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdh /dev/sg8
[0:0:8:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdi /dev/sg9
[0:0:9:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdj /dev/sg10
[0:0:10:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdk /dev/sg11
[0:0:11:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdl /dev/sg12
[0:0:12:0] enclosu LSI SAS2X28 0e12 - /dev/sg13
dmesg from latest kernel v3.17-rc3 showing (what appears to possibly
be) a kernel bug:
This happened right after I ran "lsscsi" (though can't say if it was
actually caused by that).
[ 309.327805] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000290
[ 309.335829] IP: [<ffffffffc0080d4f>]
pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
[ 309.343258] PGD 0
[ 309.345381] Oops: 0000 [#1] SMP
[ 309.348797] Modules linked in: ipmi_devintf autofs4 arc4 nfsd
auth_rpcgss intel_rapl nfs_acl x86_pkg_temp_thermal nfs
intel_powerclamp coretemp lockd kvm_intel sunrpc kvm fscache
crct10dif_pclmul ttm crc32_pclmul drm_kms_helper rt2800usb
ghash_clmulni_intel rt2x00usb rt2800lib rt2x00lib mac80211 aesni_intel
drm aes_x86_64 lrw gf128mul glue_helper ablk_helper cfg80211 cryptd
crc_ccitt syscopyarea joydev sysfillrect sysimgblt shpchp lpc_ich
ipmi_si ipmi_msghandler mac_hid video ie31200_edac edac_core lp
parport ses enclosure hid_generic usbhid hid raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx xor igb
raid6_pq i2c_algo_bit raid1 e1000e pm80xx dca raid0 libsas ahci ptp
multipath scsi_transport_sas libahci pps_core linear
[ 309.420132] CPU: 5 PID: 1998 Comm: kworker/5:2 Not tainted
3.17.0-031700rc3-generic #201409031132
[ 309.429051] Hardware name: Supermicro X10SLL-F/X10SLL-F, BIOS 2.0 04/24/2014
[ 309.436148] Workqueue: pm80xx pm8001_work_fn [pm80xx]
[ 309.441317] task: ffff880403690000 ti: ffff880404fa4000 task.ti:
ffff880404fa4000
[ 309.448867] RIP: 0010:[<ffffffffc0080d4f>] [<ffffffffc0080d4f>]
pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
[ 309.458765] RSP: 0018:ffff880404fa7cd8 EFLAGS: 00010286
[ 309.464145] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000006e02
[ 309.471342] RDX: 0000000000000000 RSI: 0000000000000286 RDI: ffff880403e98000
[ 309.478546] RBP: ffff880404fa7d18 R08: ffff880404fa4000 R09: 0000000000000000
[ 309.485749] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8804022b8000
[ 309.492954] R13: ffff880403e98000 R14: ffff880401b80180 R15: 0000000000000000
[ 309.500163] FS: 0000000000000000(0000) GS:ffff88041fd40000(0000)
knlGS:0000000000000000
[ 309.508337] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 309.514147] CR2: 0000000000000290 CR3: 0000000001c16000 CR4: 00000000001407e0
[ 309.521348] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 309.528551] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 309.535752] Stack:
[ 309.537837] ffff8804022b8000 ffff880401bbe000 ffff880401b80180
ffff880403e98000
[ 309.545599] ffff8804022b8000 ffff880401bbe000 ffff880401b80180
0000000000000000
[ 309.553349] ffff880404fa7d78 ffffffffc00826e8 ffff880404fa7d78
ffffffff810ababc
[ 309.561091] Call Trace:
[ 309.563611] [<ffffffffc00826e8>]
pm8001_I_T_nexus_event_handler+0xb8/0x1f0 [pm80xx]
[ 309.571449] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
[ 309.577355] [<ffffffffc0084559>] pm8001_work_fn+0x299/0x480 [pm80xx]
[ 309.583869] [<ffffffff8108ce6f>] process_one_work+0x17f/0x490
[ 309.589773] [<ffffffff8108d7eb>] worker_thread+0x11b/0x3f0
[ 309.595413] [<ffffffff8108d6d0>] ? create_worker+0x1e0/0x1e0
[ 309.601225] [<ffffffff81093349>] kthread+0xc9/0xe0
[ 309.606176] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
[ 309.612421] [<ffffffff817a3f3c>] ret_from_fork+0x7c/0xb0
[ 309.617890] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
[ 309.624135] Code: 00 55 48 89 e5 48 83 ec 40 4c 89 6d e8 4c 89 75
f0 49 89 fd 4c 89 7d f8 48 89 5d d8 4c 89 65 e0 48 8b 47 30 48
8b 9f 78 01 00 00 <48> 8b 80 90 02 00 00 4c 8b a0 90 01 00 00 4d 8d 74
24 38 4c 89
[ 309.647551] RIP [<ffffffffc0080d4f>]
pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
[ 309.655100] RSP <ffff880404fa7cd8>
[ 309.658657] CR2: 0000000000000290
[ 309.662045] ---[ end trace 084eaa8941942e9a ]---
[ 309.770413] BUG: unable to handle kernel paging request at ffffffffffffffd8
[ 309.777578] IP: [<ffffffff810936e0>] kthread_data+0x10/0x20
[ 309.783287] PGD 1c19067 PUD 1c1b067 PMD 0
[ 309.787652] Oops: 0000 [#2] SMP
[ 309.791080] Modules linked in: ipmi_devintf autofs4 arc4 nfsd
auth_rpcgss intel_rapl nfs_acl x86_pkg_temp_thermal nfs
intel_powerclamp coretemp lockd kvm_intel sunrpc kvm fscache
crct10dif_pclmul ttm crc32_pclmul drm_kms_helper rt2800usb
ghash_clmulni_intel rt2x00usb rt2800lib rt2x00lib mac80211 aesni_intel
drm aes_x86_64 lrw gf128mul glue_helper ablk_helper cfg80211 cryptd
crc_ccitt syscopyarea joydev sysfillrect sysimgblt shpchp lpc_ich
ipmi_si ipmi_msghandler mac_hid video ie31200_edac edac_core lp
parport ses enclosure hid_generic usbhid hid raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx xor igb
raid6_pq i2c_algo_bit raid1 e1000e pm80xx dca raid0 libsas ahci ptp
multipath scsi_transport_sas libahci pps_core linear
[ 309.862627] CPU: 5 PID: 1998 Comm: kworker/5:2 Tainted: G D
3.17.0-031700rc3-generic #201409031132
[ 309.872709] Hardware name: Supermicro X10SLL-F/X10SLL-F, BIOS 2.0 04/24/2014
[ 309.879834] task: ffff880403690000 ti: ffff880404fa4000 task.ti:
ffff880404fa4000
[ 309.887407] RIP: 0010:[<ffffffff810936e0>] [<ffffffff810936e0>]
kthread_data+0x10/0x20
[ 309.895562] RSP: 0018:ffff880404fa78e8 EFLAGS: 00010092
[ 309.900939] RAX: 0000000000000000 RBX: 0000000000000005 RCX: ffffffff81ec2e80
[ 309.908139] RDX: 0000000000000000 RSI: 0000000000000005 RDI: ffff880403690000
[ 309.915343] RBP: ffff880404fa78e8 R08: 0000000000000000 R09: 0000000000000246
[ 309.922549] R10: 000000000000001a R11: 0000000000000013 R12: 0000000000000005
[ 309.929749] R13: ffff880403690538 R14: 0000000000000001 R15: 0000000000000046
[ 309.936953] FS: 0000000000000000(0000) GS:ffff88041fd40000(0000)
knlGS:0000000000000000
[ 309.945130] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 309.950942] CR2: 0000000000000028 CR3: 0000000001c16000 CR4: 00000000001407e0
[ 309.958140] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 309.965345] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 309.972548] Stack:
[ 309.974632] ffff880404fa7908 ffffffff8108e725 ffff880404fa7908
ffff88041fd545c0
[ 309.982368] ffff880404fa7988 ffffffff8179f8b3 ffff880404fa7948
ffff880403690000
[ 309.990110] ffff880404fa7fd8 00000000000145c0 ffff880404fa7948
00000000000145c0
[ 309.997858] Call Trace:
[ 310.000377] [<ffffffff8108e725>] wq_worker_sleeping+0x15/0xb0
[ 310.006281] [<ffffffff8179f8b3>] __schedule+0x5e3/0x770
[ 310.011666] [<ffffffff8179fb19>] schedule+0x29/0x70
[ 310.016704] [<ffffffff81077795>] do_exit+0x2a5/0x470
[ 310.021830] [<ffffffff810c9fbc>] ? kmsg_dump+0x9c/0xc0
[ 310.027128] [<ffffffff81018d08>] oops_end+0xb8/0x160
[ 310.032253] [<ffffffff81788489>] no_context+0x1be/0x1cd
[ 310.037631] [<ffffffff8178866b>] __bad_area_nosemaphore+0x1d3/0x1f2
[ 310.044059] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
[ 310.049962] [<ffffffff8178869d>] bad_area_nosemaphore+0x13/0x15
[ 310.056043] [<ffffffff81062312>] __do_page_fault+0x3b2/0x550
[ 310.061856] [<ffffffff810ae3aa>] ? idle_balance+0x7a/0x2c0
[ 310.067493] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
[ 310.073399] [<ffffffff810135c6>] ? __switch_to+0xf6/0x5b0
[ 310.078960] [<ffffffff8106263e>] do_page_fault+0x3e/0x80
[ 310.084431] [<ffffffff817a6088>] page_fault+0x28/0x30
[ 310.089643] [<ffffffffc0080d4f>] ?
pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
[ 310.096957] [<ffffffffc00826e8>]
pm8001_I_T_nexus_event_handler+0xb8/0x1f0 [pm80xx]
[ 310.104791] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
[ 310.110691] [<ffffffffc0084559>] pm8001_work_fn+0x299/0x480 [pm80xx]
[ 310.117205] [<ffffffff8108ce6f>] process_one_work+0x17f/0x490
[ 310.123106] [<ffffffff8108d7eb>] worker_thread+0x11b/0x3f0
[ 310.128752] [<ffffffff8108d6d0>] ? create_worker+0x1e0/0x1e0
[ 310.134572] [<ffffffff81093349>] kthread+0xc9/0xe0
[ 310.139519] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
[ 310.145763] [<ffffffff817a3f3c>] ret_from_fork+0x7c/0xb0
[ 310.151227] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
[ 310.157473] Code: 00 48 89 e5 5d 48 8b 40 c8 48 c1 e8 02 83 e0 01
c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8b 87 c8 04 00 00
55 48 89 e5 <48> 8b 40 d8 5d c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44
00 00
[ 310.180886] RIP [<ffffffff810936e0>] kthread_data+0x10/0x20
[ 310.186679] RSP <ffff880404fa78e8>
[ 310.190239] CR2: ffffffffffffffd8
[ 310.193623] ---[ end trace 084eaa8941942e9b ]---
[ 310.306147] Fixing recursive fault but reboot is needed!
On Wed, Sep 3, 2014 at 12:06 AM, Emmanuel Florac <eflorac@intellique.com> wrote:
> Le Mon, 1 Sep 2014 09:06:46 -0700
> Andrew Robertson <andyrobertson101@gmail.com> écrivait:
>
>> I'm happy to test patches/etc on this system if necessary -- and/or if
>> someone can help point me in the right direction, I'd appreciate it.
>
> In my experience the 7xxx5 are very sensitive to cable length and
> backplane type: basically work fine with 50 cm cables, and fails with 80
> cm cables with some backplanes (works with Supermicro, not with AIC,
> etc).
>
> So what is the backplane and cables you're using?
>
> --
> ------------------------------------------------------------------------
> Emmanuel Florac | Direction technique
> | Intellique
> | <eflorac@intellique.com>
> | +33 1 78 94 84 02
> ------------------------------------------------------------------------
[-- Attachment #2: dmesg.out.txt --]
[-- Type: text/plain, Size: 211132 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.13.0-35-generic (buildd@panlong) (gcc version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #62-Ubuntu SMP Fri Aug 15 01:58:42 UTC 2014 (Ubuntu 3.13.0-35.62-generic 3.13.11.6)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-35-generic root=UUID=2ce6dd7a-f48d-4e04-86ce-1defa10caef2 ro console=tty1 console=ttyS1,115200n8 nomodeset text nomdmonddf nomdmonisw
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000008fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cd820fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cd821000-0x00000000cd827fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000cd828000-0x00000000dd818fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dd819000-0x00000000dd8fcfff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000dd8fd000-0x00000000dd945fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dd946000-0x00000000dda7afff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000dda7b000-0x00000000df7fefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000df7ff000-0x00000000df7fffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041fffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: Supermicro X10SLL-F/X10SLL-F, BIOS 2.0 04/24/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x420000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CBFFF write-protect
[ 0.000000] CC000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7C00000000 write-back
[ 0.000000] 1 base 0400000000 mask 7FE0000000 write-back
[ 0.000000] 2 base 00E0000000 mask 7FE0000000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] original variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 16GB, type WB
[ 0.000000] reg 1, base: 16GB, range: 512MB, type WB
[ 0.000000] reg 2, base: 3584MB, range: 512MB, type UC
[ 0.000000] total RAM covered: 16384M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 64K num_reg: 6 lose cover RAM: 0G
[ 0.000000] New variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 2GB, type WB
[ 0.000000] reg 1, base: 2GB, range: 1GB, type WB
[ 0.000000] reg 2, base: 3GB, range: 512MB, type WB
[ 0.000000] reg 3, base: 4GB, range: 4GB, type WB
[ 0.000000] reg 4, base: 8GB, range: 8GB, type WB
[ 0.000000] reg 5, base: 16GB, range: 512MB, type WB
[ 0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdf800 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd720-0x000fd72f] mapped at [ffff8800000fd720]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000089000] 89000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01fdf000, 0x01fdffff] PGTABLE
[ 0.000000] BRK [0x01fe0000, 0x01fe0fff] PGTABLE
[ 0.000000] BRK [0x01fe1000, 0x01fe1fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x41fe00000-0x41fffffff]
[ 0.000000] [mem 0x41fe00000-0x41fffffff] page 2M
[ 0.000000] BRK [0x01fe2000, 0x01fe2fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x41c000000-0x41fdfffff]
[ 0.000000] [mem 0x41c000000-0x41fdfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x400000000-0x41bffffff]
[ 0.000000] [mem 0x400000000-0x41bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xcd820fff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0xbfffffff] page 1G
[ 0.000000] [mem 0xc0000000-0xcd7fffff] page 2M
[ 0.000000] [mem 0xcd800000-0xcd820fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0xcd828000-0xdd818fff]
[ 0.000000] [mem 0xcd828000-0xcd9fffff] page 4k
[ 0.000000] [mem 0xcda00000-0xdd7fffff] page 2M
[ 0.000000] [mem 0xdd800000-0xdd818fff] page 4k
[ 0.000000] BRK [0x01fe3000, 0x01fe3fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0xdd8fd000-0xdd945fff]
[ 0.000000] [mem 0xdd8fd000-0xdd945fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0xdf7ff000-0xdf7fffff]
[ 0.000000] [mem 0xdf7ff000-0xdf7fffff] page 4k
[ 0.000000] BRK [0x01fe4000, 0x01fe4fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x3ffffffff]
[ 0.000000] [mem 0x100000000-0x3ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x358de000-0x36c66fff]
[ 0.000000] ACPI: RSDP 00000000000f0490 000024 (v02 SUPERM)
[ 0.000000] ACPI: XSDT 00000000dda4e098 0000B4 (v01 SUPERM SMCI--MB 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 00000000dda5b5c8 00010C (v05 SUPERM SMCI--MB 01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 00000000dda4e1e8 00D3DB (v02 SUPERM SMCI--MB 00000000 INTL 20120711)
[ 0.000000] ACPI: FACS 00000000dda7af80 000040
[ 0.000000] ACPI: APIC 00000000dda5b6d8 000092 (v03 SUPERM SMCI--MB 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 00000000dda5b770 000044 (v01 SUPERM SMCI--MB 01072009 AMI 00010013)
[ 0.000000] ACPI: SSDT 00000000dda5b7b8 000BEE (v01 Ther_R Ther_Rvp 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 00000000dda5c3a8 000540 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 00000000dda5c8e8 000B74 (v01 CpuRef CpuSsdt 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 00000000dda5d460 0002F2 (v01 PmRef Cpu0Tst 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 00000000dda5d758 000348 (v01 PmRef ApTst 00003000 INTL 20051117)
[ 0.000000] ACPI: MCFG 00000000dda5daa0 00003C (v01 SUPERM SMCI--MB 01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 00000000dda5dae0 000038 (v01 SUPERM SMCI--MB 01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 00000000dda5db18 000397 (v01 SataRe SataTabl 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 00000000dda5deb0 005B5E (v01 SaSsdt SaSsdt 00003000 INTL 20120711)
[ 0.000000] ACPI: SPMI 00000000dda63a10 000040 (v05 A M I OEMSPMI 00000000 AMI. 00000000)
[ 0.000000] ACPI: DMAR 00000000dda63a50 000080 (v01 INTEL BDW 00000001 INTL 00000001)
[ 0.000000] ACPI: EINJ 00000000dda63ad0 000130 (v01 AMI AMI EINJ 00000000 00000000)
[ 0.000000] ACPI: ERST 00000000dda63c00 000230 (v01 AMIER AMI ERST 00000000 00000000)
[ 0.000000] ACPI: HEST 00000000dda63e30 0000A8 (v01 AMI AMI HEST 00000000 00000000)
[ 0.000000] ACPI: BERT 00000000dda63ed8 000030 (v01 AMI AMI BERT 00000000 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000041fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x41fffffff]
[ 0.000000] NODE_DATA [mem 0x41fff9000-0x41fffdfff]
[ 0.000000] [ffffea0000000000-ffffea00107fffff] PMD -> [ffff88040f600000-ffff88041f5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x41fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0008efff]
[ 0.000000] node 0: [mem 0x00100000-0xcd820fff]
[ 0.000000] node 0: [mem 0xcd828000-0xdd818fff]
[ 0.000000] node 0: [mem 0xdd8fd000-0xdd945fff]
[ 0.000000] node 0: [mem 0xdf7ff000-0xdf7fffff]
[ 0.000000] node 0: [mem 0x100000000-0x41fffffff]
[ 0.000000] On node 0 totalpages: 4184042
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3982 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14114 pages used for memmap
[ 0.000000] DMA32 zone: 903260 pages, LIFO batch:31
[ 0.000000] Normal zone: 51200 pages used for memmap
[ 0.000000] Normal zone: 3276800 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00090000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcd821000-0xcd827fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdd819000-0xdd8fcfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdd946000-0xdda7afff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdda7b000-0xdf7fefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf800000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xdf800000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88041fc00000 s86336 r8192 d24256 u262144
[ 0.000000] pcpu-alloc: s86336 r8192 d24256 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 4118643
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-35-generic root=UUID=2ce6dd7a-f48d-4e04-86ce-1defa10caef2 ro console=tty1 console=ttyS1,115200n8 nomodeset text nomdmonddf nomdmonisw
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 16370396K/16736168K available (7372K kernel code, 1144K rwdata, 3404K rodata, 1336K init, 1440K bss, 365772K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
[ 0.000000] Offload RCU callbacks from all CPUs
[ 0.000000] Offload RCU callbacks from CPUs: 0-7.
[ 0.000000] NR_IRQS:16640 nr_irqs:744 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty1] enabled
[ 0.000000] console [ttyS1] enabled
[ 0.000000] allocated 67108864 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.004000] tsc: Detected 3300.108 MHz processor
[ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 6600.21 BogoMIPS (lpj=13200432)
[ 0.010880] pid_max: default: 32768 minimum: 301
[ 0.015588] Security Framework initialized
[ 0.019783] AppArmor: AppArmor initialized
[ 0.023964] Yama: becoming mindful.
[ 0.028240] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.037881] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.046124] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.053101] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.060676] Initializing cgroup subsys memory
[ 0.065121] Initializing cgroup subsys devices
[ 0.069645] Initializing cgroup subsys freezer
[ 0.074166] Initializing cgroup subsys blkio
[ 0.078519] Initializing cgroup subsys perf_event
[ 0.083303] Initializing cgroup subsys hugetlb
[ 0.087839] CPU: Physical Processor ID: 0
[ 0.091930] CPU: Processor Core ID: 0
[ 0.096939] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.096939] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.110814] mce: CPU supports 9 MCE banks
[ 0.114921] CPU0: Thermal monitoring enabled (TM1)
[ 0.119803] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.119803] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0
[ 0.119803] tlb_flushall_shift: 6
[ 0.133988] Freeing SMP alternatives memory: 32K (ffffffff81e6d000 - ffffffff81e75000)
[ 0.142703] ACPI: Core revision 20131115
[ 0.154168] ACPI: All ACPI Tables successfully acquired
[ 0.160013] ftrace: allocating 28537 entries in 112 pages
[ 0.174141] dmar: Host address width 39
[ 0.178066] dmar: DRHD base: 0x000000fed90000 flags: 0x1
[ 0.183466] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap d2008c20660462 ecap f010da
[ 0.191658] dmar: RMRR base: 0x000000df697000 end: 0x000000df6a5fff
[ 0.198065] IOAPIC id 8 under DRHD base 0xfed90000 IOMMU 0
[ 0.203700] HPET id 0 under DRHD base 0xfed90000
[ 0.208381] Your BIOS is broken and requested that x2apic be disabled.
[ 0.208381] This will slightly decrease performance.
[ 0.208381] Use 'intremap=no_x2apic_optout' to override BIOS request.
[ 0.226432] Enabled IRQ remapping in xapic mode
[ 0.231033] x2apic not enabled, IRQ remapping is in xapic mode
[ 0.237352] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.283069] smpboot: CPU0: Intel(R) Xeon(R) CPU E3-1230 v3 @ 3.30GHz (fam: 06, model: 3c, stepping: 03)
[ 0.292741] TSC deadline timer enabled
[ 0.292747] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.303253] ... version: 3
[ 0.307330] ... bit width: 48
[ 0.311492] ... generic registers: 4
[ 0.315569] ... value mask: 0000ffffffffffff
[ 0.320949] ... max period: 0000ffffffffffff
[ 0.326326] ... fixed-purpose events: 3
[ 0.330401] ... event mask: 000000070000000f
[ 0.336820] x86: Booting SMP configuration:
[ 0.358879] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.341077] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7
[ 0.452691] x86: Booted up 1 node, 8 CPUs
[ 0.457032] smpboot: Total of 8 processors activated (52801.72 BogoMIPS)
[ 0.470759] devtmpfs: initialized
[ 0.475927] EVM: security.selinux
[ 0.479315] EVM: security.SMACK64
[ 0.482701] EVM: security.ima
[ 0.485739] EVM: security.capability
[ 0.489415] PM: Registering ACPI NVS region [mem 0xcd821000-0xcd827fff] (28672 bytes)
[ 0.497337] PM: Registering ACPI NVS region [mem 0xdd946000-0xdda7afff] (1265664 bytes)
[ 0.505910] pinctrl core: initialized pinctrl subsystem
[ 0.511245] regulator-dummy: no parameters
[ 0.515447] RTC time: 21:48:22, date: 09/05/14
[ 0.519979] NET: Registered protocol family 16
[ 0.524565] cpuidle: using governor ladder
[ 0.528733] cpuidle: using governor menu
[ 0.532751] ACPI: bus type PCI registered
[ 0.536837] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.543383] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.552778] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.563569] PCI: Using configuration type 1 for base access
[ 0.569841] bio: create slab <bio-0> at 0
[ 0.574025] ACPI: Added _OSI(Module Device)
[ 0.578283] ACPI: Added _OSI(Processor Device)
[ 0.582793] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.587560] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.595776] ACPI: Executed 5 blocks of module-level executable AML code
[ 0.664542] ACPI: SSDT 00000000dd8abc18 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.673427] ACPI: Dynamic OEM Table Load:
[ 0.677636] ACPI: SSDT (null) 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.688604] ACPI: SSDT 00000000dd8ab618 0005AA (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.697545] ACPI: Dynamic OEM Table Load:
[ 0.701755] ACPI: SSDT (null) 0005AA (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.712496] ACPI: SSDT 00000000dd8aad98 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.721386] ACPI: Dynamic OEM Table Load:
[ 0.725594] ACPI: SSDT (null) 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.737208] ACPI: Interpreter enabled
[ 0.740951] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131115/hwxface-580)
[ 0.750397] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
[ 0.759828] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20131115/hwxface-580)
[ 0.769260] ACPI: (supports S0 S4 S5)
[ 0.773000] ACPI: Using IOAPIC for interrupt routing
[ 0.778060] HEST: Table parsing has been initialized.
[ 0.783184] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.792507] ACPI: No dock devices found.
[ 0.796753] ACPI: Power Resource [PG00] (on)
[ 0.808572] ACPI: Power Resource [PG01] (on)
[ 0.820556] ACPI: Power Resource [PG02] (on)
[ 0.832901] ACPI: Power Resource [FN00] (off)
[ 0.837371] ACPI: Power Resource [FN01] (off)
[ 0.841842] ACPI: Power Resource [FN02] (off)
[ 0.846316] ACPI: Power Resource [FN03] (off)
[ 0.850779] ACPI: Power Resource [FN04] (off)
[ 0.855740] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.862000] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.870568] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.879157] PCI host bridge to bus 0000:00
[ 0.883324] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.888879] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.895130] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.901373] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.908317] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff]
[ 0.915258] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[ 0.922194] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 0.929129] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 0.936068] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 1.128897] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[ 1.135838] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[ 1.142775] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfeafffff]
[ 1.149714] pci 0000:00:00.0: [8086:0c08] type 00 class 0x060000
[ 1.149774] pci 0000:00:01.0: [8086:0c01] type 01 class 0x060400
[ 1.149797] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 1.149831] pci 0000:00:01.0: System wakeup disabled by ACPI
[ 1.155576] pci 0000:00:01.1: [8086:0c05] type 01 class 0x060400
[ 1.155599] pci 0000:00:01.1: PME# supported from D0 D3hot D3cold
[ 1.155629] pci 0000:00:01.1: System wakeup disabled by ACPI
[ 1.161403] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
[ 1.161420] pci 0000:00:14.0: reg 0x10: [mem 0xf7420000-0xf742ffff 64bit]
[ 1.161471] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 1.161509] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 1.167264] pci 0000:00:19.0: [8086:153a] type 00 class 0x020000
[ 1.167279] pci 0000:00:19.0: reg 0x10: [mem 0xf7400000-0xf741ffff]
[ 1.167286] pci 0000:00:19.0: reg 0x14: [mem 0xf7435000-0xf7435fff]
[ 1.167293] pci 0000:00:19.0: reg 0x18: [io 0xf020-0xf03f]
[ 1.167343] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 1.167381] pci 0000:00:19.0: System wakeup disabled by ACPI
[ 1.173131] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320
[ 1.173149] pci 0000:00:1a.0: reg 0x10: [mem 0xf7434000-0xf74343ff]
[ 1.173225] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 1.173266] pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 1.179013] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400
[ 1.179067] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.179096] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 1.184838] pci 0000:00:1c.1: [8086:8c12] type 01 class 0x060400
[ 1.184891] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 1.184920] pci 0000:00:1c.1: System wakeup disabled by ACPI
[ 1.190686] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320
[ 1.190703] pci 0000:00:1d.0: reg 0x10: [mem 0xf7433000-0xf74333ff]
[ 1.190780] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 1.190821] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 1.196570] pci 0000:00:1f.0: [8086:8c52] type 00 class 0x060100
[ 1.196705] pci 0000:00:1f.2: [8086:8c02] type 00 class 0x010601
[ 1.196717] pci 0000:00:1f.2: reg 0x10: [io 0xf070-0xf077]
[ 1.196724] pci 0000:00:1f.2: reg 0x14: [io 0xf060-0xf063]
[ 1.196730] pci 0000:00:1f.2: reg 0x18: [io 0xf050-0xf057]
[ 1.196737] pci 0000:00:1f.2: reg 0x1c: [io 0xf040-0xf043]
[ 1.196743] pci 0000:00:1f.2: reg 0x20: [io 0xf000-0xf01f]
[ 1.196749] pci 0000:00:1f.2: reg 0x24: [mem 0xf7432000-0xf74327ff]
[ 1.196780] pci 0000:00:1f.2: PME# supported from D3hot
[ 1.196827] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
[ 1.196839] pci 0000:00:1f.3: reg 0x10: [mem 0xf7431000-0xf74310ff 64bit]
[ 1.196856] pci 0000:00:1f.3: reg 0x20: [io 0x0580-0x059f]
[ 1.196915] pci 0000:00:1f.6: [8086:8c24] type 00 class 0x118000
[ 1.196931] pci 0000:00:1f.6: reg 0x10: [mem 0xf7430000-0xf7430fff 64bit]
[ 1.197045] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.202111] pci 0000:02:00.0: [9005:8088] type 00 class 0x010700
[ 1.202120] pci 0000:02:00.0: reg 0x10: [mem 0xf7250000-0xf725ffff 64bit]
[ 1.202126] pci 0000:02:00.0: reg 0x18: [mem 0xf7240000-0xf724ffff 64bit]
[ 1.202134] pci 0000:02:00.0: reg 0x24: [mem 0xf7200000-0xf723ffff]
[ 1.202139] pci 0000:02:00.0: reg 0x30: [mem 0xf7100000-0xf71fffff pref]
[ 1.202163] pci 0000:02:00.0: supports D1
[ 1.202164] pci 0000:02:00.0: PME# supported from D0 D1 D3hot
[ 1.202176] pci 0000:02:00.0: System wakeup disabled by ACPI
[ 1.215930] pci 0000:00:01.1: PCI bridge to [bus 02]
[ 1.220967] pci 0000:00:01.1: bridge window [mem 0xf7100000-0xf72fffff]
[ 1.221049] pci 0000:03:00.0: [1a03:1150] type 01 class 0x060400
[ 1.221155] pci 0000:03:00.0: supports D1 D2
[ 1.221156] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.221180] pci 0000:03:00.0: System wakeup disabled by ACPI
[ 1.226923] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 1.237012] pci 0000:00:1c.0: PCI bridge to [bus 03-04]
[ 1.242300] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 1.242303] pci 0000:00:1c.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 1.242385] pci 0000:04:00.0: [1a03:2000] type 00 class 0x030000
[ 1.242411] pci 0000:04:00.0: reg 0x10: [mem 0xf6000000-0xf6ffffff]
[ 1.242424] pci 0000:04:00.0: reg 0x14: [mem 0xf7000000-0xf701ffff]
[ 1.242437] pci 0000:04:00.0: reg 0x18: [io 0xe000-0xe07f]
[ 1.242534] pci 0000:04:00.0: supports D1 D2
[ 1.242535] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.242618] pci 0000:03:00.0: PCI bridge to [bus 04]
[ 1.247658] pci 0000:03:00.0: bridge window [io 0xe000-0xefff]
[ 1.247663] pci 0000:03:00.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 1.247768] pci 0000:05:00.0: [8086:1533] type 00 class 0x020000
[ 1.247790] pci 0000:05:00.0: reg 0x10: [mem 0xf7300000-0xf737ffff]
[ 1.247822] pci 0000:05:00.0: reg 0x18: [io 0xd000-0xd01f]
[ 1.247838] pci 0000:05:00.0: reg 0x1c: [mem 0xf7380000-0xf7383fff]
[ 1.247975] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[ 1.248015] pci 0000:05:00.0: System wakeup disabled by ACPI
[ 1.261787] pci 0000:00:1c.1: PCI bridge to [bus 05]
[ 1.266823] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff]
[ 1.266826] pci 0000:00:1c.1: bridge window [mem 0xf7300000-0xf73fffff]
[ 1.267409] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 10 *11 12 14 15)
[ 1.274884] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 *10 11 12 14 15)
[ 1.282361] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 10 *11 12 14 15)
[ 1.289824] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 10 *11 12 14 15)
[ 1.297278] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 *10 11 12 14 15)
[ 1.304728] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 10 11 12 14 15) *0, disabled.
[ 1.313488] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 10 11 12 14 15) *0, disabled.
[ 1.322232] ACPI: PCI Interrupt Link [LNKH] (IRQs *5)
[ 1.327813] ACPI: Enabled 7 GPEs in block 00 to 3F
[ 1.332799] ACPI: \_SB_.PCI0: notify handler is installed
[ 1.332839] Found 1 acpi root devices
[ 1.332903] vgaarb: device added: PCI:0000:04:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.341072] vgaarb: loaded
[ 1.343846] vgaarb: bridge control possible 0000:04:00.0
[ 1.349309] SCSI subsystem initialized
[ 1.353147] libata version 3.00 loaded.
[ 1.353158] ACPI: bus type USB registered
[ 1.357243] usbcore: registered new interface driver usbfs
[ 1.362803] usbcore: registered new interface driver hub
[ 1.368204] usbcore: registered new device driver usb
[ 1.373389] PCI: Using ACPI for IRQ routing
[ 1.378786] PCI: pci_cache_line_size set to 64 bytes
[ 1.378847] e820: reserve RAM buffer [mem 0x0008fc00-0x0008ffff]
[ 1.378848] e820: reserve RAM buffer [mem 0xcd821000-0xcfffffff]
[ 1.378849] e820: reserve RAM buffer [mem 0xdd819000-0xdfffffff]
[ 1.378850] e820: reserve RAM buffer [mem 0xdd946000-0xdfffffff]
[ 1.378851] e820: reserve RAM buffer [mem 0xdf800000-0xdfffffff]
[ 1.378896] NetLabel: Initializing
[ 1.382368] NetLabel: domain hash size = 128
[ 1.386788] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.391827] NetLabel: unlabeled traffic allowed by default
[ 1.397515] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 1.404355] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 1.412277] Switched to clocksource hpet
[ 1.418973] AppArmor: AppArmor Filesystem Enabled
[ 1.423764] pnp: PnP ACPI init
[ 1.426898] ACPI: bus type PNP registered
[ 1.431039] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 1.437723] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 1.437729] pnp 00:01: [dma 4]
[ 1.437737] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 1.437747] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 1.437830] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.437856] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 1.437882] system 00:05: [io 0x0800-0x087f] has been reserved
[ 1.443878] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.443900] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.443919] system 00:07: [io 0x1854-0x1857] has been reserved
[ 1.449914] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 1.449959] system 00:08: [io 0x0a00-0x0a1f] has been reserved
[ 1.455948] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.456090] pnp 00:09: [dma 0 disabled]
[ 1.456116] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.456255] pnp 00:0a: [dma 0 disabled]
[ 1.456280] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.456309] system 00:0b: [io 0x04d0-0x04d1] has been reserved
[ 1.462303] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.462360] pnp 00:0c: Plug and Play ACPI device, IDs IPI0001 (active)
[ 1.462575] system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 1.469260] system 00:0d: [mem 0xfed10000-0xfed17fff] has been reserved
[ 1.475942] system 00:0d: [mem 0xfed18000-0xfed18fff] has been reserved
[ 1.491617] system 00:0d: [mem 0xfed19000-0xfed19fff] has been reserved
[ 1.498296] system 00:0d: [mem 0xf8000000-0xfbffffff] has been reserved
[ 1.504980] system 00:0d: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 1.511666] system 00:0d: [mem 0xfed90000-0xfed93fff] could not be reserved
[ 1.518697] system 00:0d: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 1.525381] system 00:0d: [mem 0xff000000-0xffffffff] has been reserved
[ 1.532064] system 00:0d: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 1.539099] system 00:0d: [mem 0xf7fe0000-0xf7feffff] has been reserved
[ 1.545779] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.545914] pnp: PnP ACPI: found 14 devices
[ 1.550176] ACPI: bus type PNP unregistered
[ 1.560342] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.565381] pci 0000:00:01.1: PCI bridge to [bus 02]
[ 1.570416] pci 0000:00:01.1: bridge window [mem 0xf7100000-0xf72fffff]
[ 1.577274] pci 0000:03:00.0: PCI bridge to [bus 04]
[ 1.582309] pci 0000:03:00.0: bridge window [io 0xe000-0xefff]
[ 1.588476] pci 0000:03:00.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 1.595340] pci 0000:00:1c.0: PCI bridge to [bus 03-04]
[ 1.600634] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 1.606800] pci 0000:00:1c.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 1.613655] pci 0000:00:1c.1: PCI bridge to [bus 05]
[ 1.618685] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff]
[ 1.624851] pci 0000:00:1c.1: bridge window [mem 0xf7300000-0xf73fffff]
[ 1.631711] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.631713] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.631714] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.631714] pci_bus 0000:00: resource 7 [mem 0x000cc000-0x000cffff]
[ 1.631715] pci_bus 0000:00: resource 8 [mem 0x000d0000-0x000d3fff]
[ 1.631716] pci_bus 0000:00: resource 9 [mem 0x000d4000-0x000d7fff]
[ 1.631717] pci_bus 0000:00: resource 10 [mem 0x000d8000-0x000dbfff]
[ 1.631718] pci_bus 0000:00: resource 11 [mem 0x000dc000-0x000dffff]
[ 1.631719] pci_bus 0000:00: resource 12 [mem 0x000e0000-0x000e3fff]
[ 1.631720] pci_bus 0000:00: resource 13 [mem 0x000e4000-0x000e7fff]
[ 1.631721] pci_bus 0000:00: resource 14 [mem 0xe0000000-0xfeafffff]
[ 1.631722] pci_bus 0000:02: resource 1 [mem 0xf7100000-0xf72fffff]
[ 1.631723] pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
[ 1.631724] pci_bus 0000:03: resource 1 [mem 0xf6000000-0xf70fffff]
[ 1.631725] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 1.631726] pci_bus 0000:04: resource 1 [mem 0xf6000000-0xf70fffff]
[ 1.631727] pci_bus 0000:05: resource 0 [io 0xd000-0xdfff]
[ 1.631728] pci_bus 0000:05: resource 1 [mem 0xf7300000-0xf73fffff]
[ 1.631744] NET: Registered protocol family 2
[ 1.636290] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.643918] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.650788] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.657494] TCP: reno registered
[ 1.660818] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.667019] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.673686] NET: Registered protocol family 1
[ 1.716072] pci 0000:04:00.0: Boot video device
[ 1.716087] PCI: CLS 64 bytes, default 64
[ 1.716123] Trying to unpack rootfs image as initramfs...
[ 1.935470] Freeing initrd memory: 20004K (ffff8800358de000 - ffff880036c67000)
[ 1.942901] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.949418] software IO TLB [mem 0xd9819000-0xdd819000] (64MB) mapped at [ffff8800d9819000-ffff8800dd818fff]
[ 1.959545] microcode: CPU0 sig=0x306c3, pf=0x2, revision=0x17
[ 1.965456] microcode: CPU1 sig=0x306c3, pf=0x2, revision=0x17
[ 1.971361] microcode: CPU2 sig=0x306c3, pf=0x2, revision=0x17
[ 1.977285] microcode: CPU3 sig=0x306c3, pf=0x2, revision=0x17
[ 1.983185] microcode: CPU4 sig=0x306c3, pf=0x2, revision=0x17
[ 1.989086] microcode: CPU5 sig=0x306c3, pf=0x2, revision=0x17
[ 1.994988] microcode: CPU6 sig=0x306c3, pf=0x2, revision=0x17
[ 2.000898] microcode: CPU7 sig=0x306c3, pf=0x2, revision=0x17
[ 2.006839] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 2.015720] Scanning for low memory corruption every 60 seconds
[ 2.021895] Initialise system trusted keyring
[ 2.026357] audit: initializing netlink socket (disabled)
[ 2.031837] type=2000 audit(1409953701.656:1): initialized
[ 2.055046] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.062246] zbud: loaded
[ 2.064947] VFS: Disk quotas dquot_6.5.2
[ 2.068965] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.075728] fuse init (API version 7.22)
[ 2.079770] msgmni has been set to 32012
[ 2.083800] Key type big_key registered
[ 2.088025] Key type asymmetric registered
[ 2.092193] Asymmetric key parser 'x509' registered
[ 2.097158] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 2.104678] io scheduler noop registered
[ 2.108669] io scheduler deadline registered (default)
[ 2.113886] io scheduler cfq registered
[ 2.117916] pcieport 0000:00:01.0: irq 41 for MSI/MSI-X
[ 2.117998] pcieport 0000:00:01.1: irq 42 for MSI/MSI-X
[ 2.118086] pcieport 0000:00:1c.0: irq 43 for MSI/MSI-X
[ 2.118183] pcieport 0000:00:1c.1: irq 44 for MSI/MSI-X
[ 2.118239] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
[ 2.125278] pcie_pme 0000:00:01.0:pcie01: service driver pcie_pme loaded
[ 2.125285] pcieport 0000:00:01.1: Signaling PME through PCIe PME interrupt
[ 2.132322] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[ 2.138915] pcie_pme 0000:00:01.1:pcie01: service driver pcie_pme loaded
[ 2.138924] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 2.145956] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 2.152556] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[ 2.159151] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 2.159160] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
[ 2.166184] pci 0000:05:00.0: Signaling PME through PCIe PME interrupt
[ 2.172782] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
[ 2.172790] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 2.178439] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 2.185150] intel_idle: MWAIT substates: 0x42120
[ 2.185150] intel_idle: v0.4 model 0x3C
[ 2.185151] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 2.185264] ipmi message handler version 39.2
[ 2.189743] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0
[ 2.198019] ACPI: Sleep Button [SLPB]
[ 2.201768] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 2.210035] ACPI: Power Button [PWRB]
[ 2.213776] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 2.221265] ACPI: Power Button [PWRF]
[ 2.225023] ACPI: Fan [FAN0] (off)
[ 2.228513] ACPI: Fan [FAN1] (off)
[ 2.232000] ACPI: Fan [FAN2] (off)
[ 2.235489] ACPI: Fan [FAN3] (off)
[ 2.238971] ACPI: Fan [FAN4] (off)
[ 2.244043] thermal LNXTHERM:00: registered as thermal_zone0
[ 2.249781] ACPI: Thermal Zone [TZ00] (28 C)
[ 2.254242] thermal LNXTHERM:01: registered as thermal_zone1
[ 2.259978] ACPI: Thermal Zone [TZ01] (30 C)
[ 2.264357] ERST: Error Record Serialization Table (ERST) support is initialized.
[ 2.271934] pstore: Registered erst as persistent store backend
[ 2.277996] GHES: APEI firmware first mode is enabled by APEI bit and WHEA _OSC.
[ 2.285541] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 2.312561] 00:09: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 2.340552] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 2.348919] Linux agpgart interface v0.103
[ 2.353889] brd: module loaded
[ 2.357417] loop: module loaded
[ 2.360824] libphy: Fixed MDIO Bus: probed
[ 2.365038] tun: Universal TUN/TAP device driver, 1.6
[ 2.370166] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.376453] PPP generic driver version 2.4.2
[ 2.380840] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.387443] ehci-pci: EHCI PCI platform driver
[ 2.392032] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 2.397328] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.404821] ehci-pci 0000:00:1a.0: debug port 2
[ 2.413319] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 2.413328] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7434000
[ 2.427299] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 2.433134] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.439997] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.447306] usb usb1: Product: EHCI Host Controller
[ 2.452252] usb usb1: Manufacturer: Linux 3.13.0-35-generic ehci_hcd
[ 2.458669] usb usb1: SerialNumber: 0000:00:1a.0
[ 2.463427] hub 1-0:1.0: USB hub found
[ 2.467260] hub 1-0:1.0: 2 ports detected
[ 2.471473] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 2.476768] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.484259] ehci-pci 0000:00:1d.0: debug port 2
[ 2.492739] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 2.492748] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7433000
[ 2.507220] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 2.513054] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.519914] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.527223] usb usb2: Product: EHCI Host Controller
[ 2.532167] usb usb2: Manufacturer: Linux 3.13.0-35-generic ehci_hcd
[ 2.538588] usb usb2: SerialNumber: 0000:00:1d.0
[ 2.543345] hub 2-0:1.0: USB hub found
[ 2.547176] hub 2-0:1.0: 2 ports detected
[ 2.551325] ehci-platform: EHCI generic platform driver
[ 2.556629] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.562883] ohci-pci: OHCI PCI platform driver
[ 2.567404] ohci-platform: OHCI generic platform driver
[ 2.572716] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.579220] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 2.584523] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 2.592086] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 2.592109] xhci_hcd 0000:00:14.0: irq 45 for MSI/MSI-X
[ 2.592153] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.599014] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.606325] usb usb3: Product: xHCI Host Controller
[ 2.611270] usb usb3: Manufacturer: Linux 3.13.0-35-generic xhci_hcd
[ 2.617687] usb usb3: SerialNumber: 0000:00:14.0
[ 2.622448] hub 3-0:1.0: USB hub found
[ 2.626283] hub 3-0:1.0: 10 ports detected
[ 2.631726] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 2.637020] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[ 2.644521] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.651384] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.658687] usb usb4: Product: xHCI Host Controller
[ 2.663637] usb usb4: Manufacturer: Linux 3.13.0-35-generic xhci_hcd
[ 2.670055] usb usb4: SerialNumber: 0000:00:14.0
[ 2.674828] hub 4-0:1.0: USB hub found
[ 2.678664] hub 4-0:1.0: 2 ports detected
[ 2.687187] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 2.782993] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 2.954809] tsc: Refined TSC clocksource calibration: 3299.995 MHz
[ 3.202835] usb 1-1: New USB device found, idVendor=8087, idProduct=8008
[ 3.209605] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.216960] hub 1-1:1.0: USB hub found
[ 3.220938] hub 1-1:1.0: 4 ports detected
[ 3.334413] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 3.470695] usb 2-1: New USB device found, idVendor=8087, idProduct=8000
[ 3.477462] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.484825] hub 2-1:1.0: USB hub found
[ 3.488681] hub 2-1:1.0: 6 ports detected
[ 3.614142] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[ 3.652158] usb 3-1: New USB device found, idVendor=148f, idProduct=5370
[ 3.658922] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.666123] usb 3-1: Product: 802.11 n WLAN
[ 3.670372] usb 3-1: Manufacturer: Ralink
[ 3.674450] usb 3-1: SerialNumber: 1.0
[ 3.765581] i8042: No controller found
[ 3.769467] mousedev: PS/2 mouse device common for all mice
[ 3.775420] rtc_cmos 00:06: RTC can wake from S4
[ 3.780245] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 3.786435] rtc_cmos 00:06: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 3.794223] device-mapper: uevent: version 1.0.3
[ 3.798971] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[ 3.807505] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.813647] TCP: cubic registered
[ 3.817082] NET: Registered protocol family 10
[ 3.821700] NET: Registered protocol family 17
[ 3.826228] Key type dns_resolver registered
[ 3.830792] Loading compiled-in X.509 certificates
[ 3.836176] Loaded X.509 cert 'Magrathea: Glacier signing key: b1414ae96c1b0ebb7c141fa405c1f6c98e8a66f0'
[ 3.845750] registered taskstats version 1
[ 3.849954] usb 3-3: new high-speed USB device number 3 using xhci_hcd
[ 3.851345] Key type trusted registered
[ 3.852445] Key type encrypted registered
[ 3.853476] AppArmor: AppArmor sha1 policy hashing enabled
[ 3.853477] IMA: No TPM chip found, activating TPM-bypass!
[ 3.853849] regulator-dummy: disabling
[ 3.853930] Magic number: 14:409:853
[ 3.883261] rtc_cmos 00:06: setting system clock to 2014-09-05 21:48:25 UTC (1409953705)
[ 3.892394] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 3.898152] usb 3-3: New USB device found, idVendor=0000, idProduct=0001
[ 3.898153] usb 3-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.898458] hub 3-3:1.0: USB hub found
[ 3.898539] hub 3-3:1.0: 4 ports detected
[ 3.920334] EDD information not available.
[ 3.924522] PM: Hibernation image not present or could not be loaded.
[ 3.925126] Freeing unused kernel memory: 1336K (ffffffff81d1f000 - ffffffff81e6d000)
[ 3.933039] Write protecting the kernel read-only data: 12288k
[ 3.940236] Freeing unused kernel memory: 808K (ffff880001736000 - ffff880001800000)
[ 3.949047] Freeing unused kernel memory: 692K (ffff880001b53000 - ffff880001c00000)
[ 3.956888] Switched to clocksource tsc
[ 3.966177] systemd-udevd[148]: starting version 204
[ 3.974548] md: linear personality registered for level -1
[ 3.981092] pps_core: LinuxPPS API ver. 1 registered
[ 3.986425] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 3.995702] md: multipath personality registered for level -4
[ 4.001632] PTP clock support registered
[ 4.005665] md: raid0 personality registered for level 0
[ 4.005681] ahci 0000:00:1f.2: version 3.0
[ 4.005799] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X
[ 4.005873] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[ 4.005874] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst
[ 4.027002] dca service started, version 1.12.1
[ 4.027020] pm80xx 0000:02:00.0: pm80xx: driver version 0.1.37
[ 4.037529] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 4.043438] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 4.046008] scsi1 : ahci
[ 4.046053] scsi2 : ahci
[ 4.046084] scsi3 : ahci
[ 4.046114] scsi4 : ahci
[ 4.046145] scsi5 : ahci
[ 4.046174] scsi6 : ahci
[ 4.046193] ata1: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432100 irq 46
[ 4.046196] ata2: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432180 irq 46
[ 4.046197] ata3: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432200 irq 46
[ 4.046200] ata4: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432280 irq 46
[ 4.046201] ata5: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432300 irq 46
[ 4.046204] ata6: SATA max UDMA/133 abar m2048@0xf7432000 port 0xf7432380 irq 46
[ 4.069697] usb 3-5: new full-speed USB device number 4 using xhci_hcd
[ 4.086848] usb 3-5: New USB device found, idVendor=051d, idProduct=0003
[ 4.086849] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.086850] usb 3-5: Product: Smart-UPS C 1500 FW:UPS 09.6 / ID=1005
[ 4.086851] usb 3-5: Manufacturer: American Power Conversion
[ 4.086851] usb 3-5: SerialNumber: 3S1424X00597
[ 4.086946] usb 3-5: ep 0x81 - rounding interval to 128 microframes, ep desc says 160 microframes
[ 4.086948] usb 3-5: ep 0x1 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 4.165151] md: raid1 personality registered for level 1
[ 4.165309] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 4.165334] e1000e 0000:00:19.0: irq 47 for MSI/MSI-X
[ 4.179985] hidraw: raw HID events driver (C) Jiri Kosina
[ 4.185503] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.5-k
[ 4.192536] igb: Copyright (c) 2007-2013 Intel Corporation.
[ 4.193596] usb 3-3.1: new low-speed USB device number 5 using xhci_hcd
[ 4.205493] igb 0000:05:00.0: irq 48 for MSI/MSI-X
[ 4.205498] igb 0000:05:00.0: irq 49 for MSI/MSI-X
[ 4.205501] igb 0000:05:00.0: irq 50 for MSI/MSI-X
[ 4.205505] igb 0000:05:00.0: irq 51 for MSI/MSI-X
[ 4.205509] igb 0000:05:00.0: irq 52 for MSI/MSI-X
[ 4.206178] usbcore: registered new interface driver usbhid
[ 4.211840] usbhid: USB HID core driver
[ 4.217599] usb 3-3.1: New USB device found, idVendor=0557, idProduct=2419
[ 4.220161] hid-generic 0003:051D:0003.0001: hiddev0,hidraw0: USB HID v1.00 Device [American Power Conversion Smart-UPS C 1500 FW:UPS 09.6 / ID=1005] on usb-0000:00:14.0-5/input0
[ 4.240667] usb 3-3.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.248106] usb 3-3.1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 4.249504] raid6: sse2x1 7925 MB/s
[ 4.250039] igb 0000:05:00.0: added PHC on eth0
[ 4.250040] igb 0000:05:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 4.250041] igb 0000:05:00.0: eth0: (PCIe:2.5Gb/s:Width x1) 00:25:90:44:09:82
[ 4.250143] igb 0000:05:00.0: eth0: PBA No: 011000-000
[ 4.250144] igb 0000:05:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
[ 4.292463] usb 3-3.1: ep 0x82 - rounding interval to 32 microframes, ep desc says 40 microframes
[ 4.302451] input: HID 0557:2419 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.1/3-3.1:1.0/input/input3
[ 4.312314] hid-generic 0003:0557:2419.0002: input,hidraw1: USB HID v1.00 Keyboard [HID 0557:2419] on usb-0000:00:14.0-3.1/input0
[ 4.317450] raid6: sse2x2 10040 MB/s
[ 4.328629] input: HID 0557:2419 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.1/3-3.1:1.1/input/input4
[ 4.338676] hid-generic 0003:0557:2419.0003: input,hidraw2: USB HID v1.00 Mouse [HID 0557:2419] on usb-0000:00:14.0-3.1/input1
[ 4.369419] ata6: SATA link down (SStatus 0 SControl 300)
[ 4.374918] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.380396] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.385385] raid6: sse2x4 10930 MB/s
[ 4.401388] ata5: SATA link down (SStatus 0 SControl 300)
[ 4.406863] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.412346] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.419423] ata3.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 4.419424] ata3.00: ATA-9: Samsung SSD 840 PRO Series, DXM06B0Q, max UDMA/133
[ 4.426732] ata3.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 4.434242] ata3.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 4.434245] ata3.00: configured for UDMA/133
[ 4.445462] scsi 3:0:0:0: Direct-Access ATA Samsung SSD 840 DXM0 PQ: 0 ANSI: 5
[ 4.453315] raid6: avx2x1 15947 MB/s
[ 4.457562] sd 3:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[ 4.465176] sd 3:0:0:0: [sda] Write Protect is off
[ 4.465312] sd 3:0:0:0: Attached scsi generic sg0 type 0
[ 4.475434] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.475443] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.485059] sda: sda1 sda2 < sda5 >
[ 4.489056] sd 3:0:0:0: [sda] Attached SCSI disk
[ 4.521248] raid6: avx2x2 19644 MB/s
[ 4.589181] raid6: avx2x4 23898 MB/s
[ 4.593006] raid6: using algorithm avx2x4 (23898 MB/s)
[ 4.598219] raid6: using avx2x2 recovery algorithm
[ 4.603938] xor: automatically using best checksumming function:
[ 4.649127] avx : 28712.000 MB/sec
[ 4.654167] async_tx: api initialized (async)
[ 4.663402] md: raid6 personality registered for level 6
[ 4.668802] md: raid5 personality registered for level 5
[ 4.674188] md: raid4 personality registered for level 4
[ 4.682317] md: raid10 personality registered for level 10
[ 4.697492] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 4.705313] EXT4-fs (sda1): write access will be enabled during recovery
[ 4.723814] EXT4-fs (sda1): recovery complete
[ 4.729544] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 4.910633] scsi0 : pm80xx
[ 4.913684] pm80xx 0000:02:00.0: irq 53 for MSI/MSI-X
[ 4.913698] pm80xx 0000:02:00.0: irq 54 for MSI/MSI-X
[ 4.913702] pm80xx 0000:02:00.0: irq 55 for MSI/MSI-X
[ 4.913706] pm80xx 0000:02:00.0: irq 56 for MSI/MSI-X
[ 4.913710] pm80xx 0000:02:00.0: irq 57 for MSI/MSI-X
[ 4.913714] pm80xx 0000:02:00.0: irq 58 for MSI/MSI-X
[ 4.913718] pm80xx 0000:02:00.0: irq 59 for MSI/MSI-X
[ 4.913722] pm80xx 0000:02:00.0: irq 60 for MSI/MSI-X
[ 4.913725] pm80xx 0000:02:00.0: irq 61 for MSI/MSI-X
[ 4.913729] pm80xx 0000:02:00.0: irq 62 for MSI/MSI-X
[ 4.913733] pm80xx 0000:02:00.0: irq 63 for MSI/MSI-X
[ 4.913737] pm80xx 0000:02:00.0: irq 64 for MSI/MSI-X
[ 4.913740] pm80xx 0000:02:00.0: irq 65 for MSI/MSI-X
[ 4.913744] pm80xx 0000:02:00.0: irq 66 for MSI/MSI-X
[ 4.913748] pm80xx 0000:02:00.0: irq 67 for MSI/MSI-X
[ 4.913751] pm80xx 0000:02:00.0: irq 68 for MSI/MSI-X
[ 4.913755] pm80xx 0000:02:00.0: irq 69 for MSI/MSI-X
[ 4.913759] pm80xx 0000:02:00.0: irq 70 for MSI/MSI-X
[ 4.913762] pm80xx 0000:02:00.0: irq 71 for MSI/MSI-X
[ 4.913766] pm80xx 0000:02:00.0: irq 72 for MSI/MSI-X
[ 4.913769] pm80xx 0000:02:00.0: irq 73 for MSI/MSI-X
[ 4.913773] pm80xx 0000:02:00.0: irq 74 for MSI/MSI-X
[ 4.913777] pm80xx 0000:02:00.0: irq 75 for MSI/MSI-X
[ 4.913780] pm80xx 0000:02:00.0: irq 76 for MSI/MSI-X
[ 4.913784] pm80xx 0000:02:00.0: irq 77 for MSI/MSI-X
[ 4.913787] pm80xx 0000:02:00.0: irq 78 for MSI/MSI-X
[ 4.913791] pm80xx 0000:02:00.0: irq 79 for MSI/MSI-X
[ 4.913795] pm80xx 0000:02:00.0: irq 80 for MSI/MSI-X
[ 4.913799] pm80xx 0000:02:00.0: irq 81 for MSI/MSI-X
[ 4.913802] pm80xx 0000:02:00.0: irq 82 for MSI/MSI-X
[ 4.913806] pm80xx 0000:02:00.0: irq 83 for MSI/MSI-X
[ 4.913810] pm80xx 0000:02:00.0: irq 84 for MSI/MSI-X
[ 4.913813] pm80xx 0000:02:00.0: irq 85 for MSI/MSI-X
[ 4.913817] pm80xx 0000:02:00.0: irq 86 for MSI/MSI-X
[ 4.913820] pm80xx 0000:02:00.0: irq 87 for MSI/MSI-X
[ 4.913824] pm80xx 0000:02:00.0: irq 88 for MSI/MSI-X
[ 4.913827] pm80xx 0000:02:00.0: irq 89 for MSI/MSI-X
[ 4.913831] pm80xx 0000:02:00.0: irq 90 for MSI/MSI-X
[ 4.913835] pm80xx 0000:02:00.0: irq 91 for MSI/MSI-X
[ 4.913838] pm80xx 0000:02:00.0: irq 92 for MSI/MSI-X
[ 4.913842] pm80xx 0000:02:00.0: irq 93 for MSI/MSI-X
[ 4.913845] pm80xx 0000:02:00.0: irq 94 for MSI/MSI-X
[ 4.913849] pm80xx 0000:02:00.0: irq 95 for MSI/MSI-X
[ 4.913853] pm80xx 0000:02:00.0: irq 96 for MSI/MSI-X
[ 4.913856] pm80xx 0000:02:00.0: irq 97 for MSI/MSI-X
[ 4.913860] pm80xx 0000:02:00.0: irq 98 for MSI/MSI-X
[ 4.913864] pm80xx 0000:02:00.0: irq 99 for MSI/MSI-X
[ 4.913867] pm80xx 0000:02:00.0: irq 100 for MSI/MSI-X
[ 4.913871] pm80xx 0000:02:00.0: irq 101 for MSI/MSI-X
[ 4.913874] pm80xx 0000:02:00.0: irq 102 for MSI/MSI-X
[ 4.913878] pm80xx 0000:02:00.0: irq 103 for MSI/MSI-X
[ 4.913882] pm80xx 0000:02:00.0: irq 104 for MSI/MSI-X
[ 4.913885] pm80xx 0000:02:00.0: irq 105 for MSI/MSI-X
[ 4.913889] pm80xx 0000:02:00.0: irq 106 for MSI/MSI-X
[ 4.913893] pm80xx 0000:02:00.0: irq 107 for MSI/MSI-X
[ 4.913896] pm80xx 0000:02:00.0: irq 108 for MSI/MSI-X
[ 4.913900] pm80xx 0000:02:00.0: irq 109 for MSI/MSI-X
[ 4.913903] pm80xx 0000:02:00.0: irq 110 for MSI/MSI-X
[ 4.913907] pm80xx 0000:02:00.0: irq 111 for MSI/MSI-X
[ 4.913911] pm80xx 0000:02:00.0: irq 112 for MSI/MSI-X
[ 4.913914] pm80xx 0000:02:00.0: irq 113 for MSI/MSI-X
[ 4.913918] pm80xx 0000:02:00.0: irq 114 for MSI/MSI-X
[ 4.913922] pm80xx 0000:02:00.0: irq 115 for MSI/MSI-X
[ 4.913925] pm80xx 0000:02:00.0: irq 116 for MSI/MSI-X
[ 4.928948] systemd-udevd[153]: renamed network interface eth0 to em1
[ 4.929069] e1000e 0000:00:19.0 eth0: registered PHC clock
[ 4.929070] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:44:09:83
[ 4.929071] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 4.929105] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: 0100FF-0FF
[ 4.977001] systemd-udevd[150]: renamed network interface eth0 to em2
[ 5.414147] sas: phy-0:0 added to port-0:0, phy_mask:0x1 (5003048001108c3f)
[ 5.414152] sas: phy1 matched wide port0
[ 5.414155] sas: phy-0:1 added to port-0:0, phy_mask:0x3 (5003048001108c3f)
[ 5.414160] sas: DOING DISCOVERY on port 0, pid:196
[ 5.414575] sas: ex 5003048001108c3f phy00:S:A attached: 50000d1106da2000 (host)
[ 5.414756] sas: ex 5003048001108c3f phy01:S:A attached: 50000d1106da2000 (host)
[ 5.414935] sas: ex 5003048001108c3f phy02:S:A attached: 50000d1106da2000 (host)
[ 5.415117] sas: ex 5003048001108c3f phy03:S:A attached: 50000d1106da2000 (host)
[ 5.415364] sas: ex 5003048001108c3f phy04:U:0 attached: 0000000000000000 (no device)
[ 5.415666] sas: ex 5003048001108c3f phy05:U:0 attached: 0000000000000000 (no device)
[ 5.415903] sas: ex 5003048001108c3f phy06:U:0 attached: 0000000000000000 (no device)
[ 5.416207] sas: ex 5003048001108c3f phy07:U:0 attached: 0000000000000000 (no device)
[ 5.416445] sas: ex 5003048001108c3f phy08:U:0 attached: 0000000000000000 (no device)
[ 5.416691] sas: ex 5003048001108c3f phy09:U:0 attached: 0000000000000000 (no device)
[ 5.416927] sas: ex 5003048001108c3f phy10:U:0 attached: 0000000000000000 (no device)
[ 5.417159] sas: ex 5003048001108c3f phy11:U:0 attached: 0000000000000000 (no device)
[ 5.417392] sas: ex 5003048001108c3f phy12:U:A attached: 5003048001108c0c (stp)
[ 5.417621] sas: ex 5003048001108c3f phy13:U:A attached: 5003048001108c0d (stp)
[ 5.417853] sas: ex 5003048001108c3f phy14:U:A attached: 5003048001108c0e (stp)
[ 5.418081] sas: ex 5003048001108c3f phy15:U:A attached: 5003048001108c0f (stp)
[ 5.418312] sas: ex 5003048001108c3f phy16:U:A attached: 5003048001108c10 (stp)
[ 5.418544] sas: ex 5003048001108c3f phy17:U:A attached: 5003048001108c11 (stp)
[ 5.418772] sas: ex 5003048001108c3f phy18:U:0 attached: 0000000000000000 (no device)
[ 5.419001] sas: ex 5003048001108c3f phy19:U:0 attached: 0000000000000000 (no device)
[ 5.419231] sas: ex 5003048001108c3f phy20:U:0 attached: 0000000000000000 (no device)
[ 5.419459] sas: ex 5003048001108c3f phy21:U:0 attached: 0000000000000000 (no device)
[ 5.419688] sas: ex 5003048001108c3f phy22:U:0 attached: 0000000000000000 (no device)
[ 5.419917] sas: ex 5003048001108c3f phy23:U:0 attached: 0000000000000000 (no device)
[ 5.420147] sas: ex 5003048001108c3f phy24:U:0 attached: 0000000000000000 (no device)
[ 5.420385] sas: ex 5003048001108c3f phy25:U:0 attached: 0000000000000000 (no device)
[ 5.420599] sas: ex 5003048001108c3f phy26:U:0 attached: 0000000000000000 (no device)
[ 5.420813] sas: ex 5003048001108c3f phy27:U:0 attached: 0000000000000000 (no device)
[ 5.421043] sas: ex 5003048001108c3f phy28:U:0 attached: 0000000000000000 (no device)
[ 5.421277] sas: ex 5003048001108c3f phy29:U:0 attached: 0000000000000000 (no device)
[ 5.421511] sas: ex 5003048001108c3f phy30:U:0 attached: 0000000000000000 (no device)
[ 5.421742] sas: ex 5003048001108c3f phy31:U:0 attached: 0000000000000000 (no device)
[ 5.421971] sas: ex 5003048001108c3f phy32:U:0 attached: 0000000000000000 (no device)
[ 5.422200] sas: ex 5003048001108c3f phy33:U:0 attached: 0000000000000000 (no device)
[ 5.422430] sas: ex 5003048001108c3f phy34:U:0 attached: 0000000000000000 (no device)
[ 5.422657] sas: ex 5003048001108c3f phy35:U:0 attached: 0000000000000000 (no device)
[ 5.422883] sas: ex 5003048001108c3f phy36:D:A attached: 5003048001108c3d (host+target)
[ 5.423108] sas: ex 5003048001108c3f phy37:D:0 attached: 0000000000000000 (no device)
[ 5.480386] sas: DONE DISCOVERY on port 0, pid:196, result:0
[ 5.480390] sas: phy2 matched wide port0
[ 5.480395] sas: phy-0:2 added to port-0:0, phy_mask:0x7 (5003048001108c3f)
[ 5.480439] sas: phy-0:4 added to port-0:1, phy_mask:0x10 (50030480010f713f)
[ 5.480441] sas: phy3 matched wide port0
[ 5.480442] sas: phy-0:3 added to port-0:0, phy_mask:0xf (5003048001108c3f)
[ 5.480443] sas: phy5 matched wide port1
[ 5.480445] sas: phy-0:5 added to port-0:1, phy_mask:0x30 (50030480010f713f)
[ 5.480446] sas: phy7 matched wide port1
[ 5.480448] sas: phy-0:7 added to port-0:1, phy_mask:0xb0 (50030480010f713f)
[ 5.480449] sas: phy6 matched wide port1
[ 5.480451] sas: phy-0:6 added to port-0:1, phy_mask:0xf0 (50030480010f713f)
[ 5.480461] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 5.480475] sas: ata7: end_device-0:0:12: dev error handler
[ 5.480492] sas: ata8: end_device-0:0:13: dev error handler
[ 5.480493] sas: ata9: end_device-0:0:14: dev error handler
[ 5.480498] sas: ata10: end_device-0:0:15: dev error handler
[ 5.480502] sas: ata11: end_device-0:0:16: dev error handler
[ 5.480632] sas: ata12: end_device-0:0:17: dev error handler
[ 7.639340] ata7.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.639437] ata8.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.639438] ata8.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.639548] ata9.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.639549] ata9.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.639820] ata10.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 7.639820] ata10.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.639963] ata8.00: configured for UDMA/133
[ 7.640069] ata9.00: configured for UDMA/133
[ 7.640350] ata10.00: configured for UDMA/133
[ 7.709554] ata7.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.717075] ata7.00: configured for UDMA/133
[ 27.514797] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 27.514824] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 27.671580] ata11.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 27.678454] ata11.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 27.683249] ata12.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 27.683250] ata12.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 27.683769] ata12.00: configured for UDMA/133
[ 27.704530] ata11.00: configured for UDMA/133
[ 27.708992] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 27.722811] scsi 0:0:0:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.731153] scsi 0:0:1:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.739484] scsi 0:0:2:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.747812] scsi 0:0:3:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.756143] scsi 0:0:4:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.764476] scsi 0:0:5:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 27.773048] scsi 0:0:6:0: Enclosure LSI SAS2X36 0e12 PQ: 0 ANSI: 5
[ 27.782523] sas: DOING DISCOVERY on port 1, pid:196
[ 27.783139] sas: ex 50030480010f713f phy00:S:A attached: 50000d1106da2000 (host)
[ 27.783386] sas: ex 50030480010f713f phy01:S:A attached: 50000d1106da2000 (host)
[ 27.783702] sas: ex 50030480010f713f phy02:S:A attached: 50000d1106da2000 (host)
[ 27.783957] sas: ex 50030480010f713f phy03:S:A attached: 50000d1106da2000 (host)
[ 27.784270] sas: ex 50030480010f713f phy04:U:0 attached: 0000000000000000 (no device)
[ 27.784522] sas: ex 50030480010f713f phy05:U:0 attached: 0000000000000000 (no device)
[ 27.784836] sas: ex 50030480010f713f phy06:U:0 attached: 0000000000000000 (no device)
[ 27.785096] sas: ex 50030480010f713f phy07:U:0 attached: 0000000000000000 (no device)
[ 27.785382] sas: ex 50030480010f713f phy08:D:1 attached: 0000000000000000 (no device)
[ 27.785630] sas: ex 50030480010f713f phy09:D:1 attached: 0000000000000000 (no device)
[ 27.785870] sas: ex 50030480010f713f phy10:D:1 attached: 0000000000000000 (no device)
[ 27.786107] sas: ex 50030480010f713f phy11:D:1 attached: 0000000000000000 (no device)
[ 27.786345] sas: ex 50030480010f713f phy12:U:A attached: 50030480010f712c (stp)
[ 27.786588] sas: ex 50030480010f713f phy13:U:A attached: 50030480010f712d (stp)
[ 27.786826] sas: ex 50030480010f713f phy14:U:A attached: 50030480010f712e (stp)
[ 27.787064] sas: ex 50030480010f713f phy15:U:A attached: 50030480010f712f (stp)
[ 27.787305] sas: ex 50030480010f713f phy16:U:A attached: 50030480010f7130 (stp)
[ 27.787544] sas: ex 50030480010f713f phy17:U:0 attached: 0000000000000000 (no device)
[ 27.787781] sas: ex 50030480010f713f phy18:U:0 attached: 0000000000000000 (no device)
[ 27.788018] sas: ex 50030480010f713f phy19:U:0 attached: 0000000000000000 (no device)
[ 27.788254] sas: ex 50030480010f713f phy20:U:0 attached: 0000000000000000 (no device)
[ 27.788492] sas: ex 50030480010f713f phy21:U:0 attached: 0000000000000000 (no device)
[ 27.788731] sas: ex 50030480010f713f phy22:U:0 attached: 0000000000000000 (no device)
[ 27.788970] sas: ex 50030480010f713f phy23:U:0 attached: 0000000000000000 (no device)
[ 27.789206] sas: ex 50030480010f713f phy24:D:1 attached: 0000000000000000 (no device)
[ 27.789444] sas: ex 50030480010f713f phy25:D:1 attached: 0000000000000000 (no device)
[ 27.789682] sas: ex 50030480010f713f phy26:D:1 attached: 0000000000000000 (no device)
[ 27.789920] sas: ex 50030480010f713f phy27:D:1 attached: 0000000000000000 (no device)
[ 27.790155] sas: ex 50030480010f713f phy28:D:A attached: 50030480010f713d (host+target)
[ 27.790391] sas: ex 50030480010f713f phy29:D:0 attached: 0000000000000000 (no device)
[ 27.846476] sas: DONE DISCOVERY on port 1, pid:196, result:0
[ 27.846480] sas: broadcast received: 9
[ 27.846483] sas: broadcast received: 9
[ 27.846484] sas: broadcast received: 9
[ 27.846484] sas: broadcast received: 9
[ 27.846508] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 27.846551] sas: ata7: end_device-0:0:12: dev error handler
[ 27.846575] sas: ata8: end_device-0:0:13: dev error handler
[ 27.846581] sas: ata9: end_device-0:0:14: dev error handler
[ 27.846582] sas: ata10: end_device-0:0:15: dev error handler
[ 27.846588] sas: ata11: end_device-0:0:16: dev error handler
[ 27.846589] sas: ata12: end_device-0:0:17: dev error handler
[ 27.846595] sas: ata14: end_device-0:1:13: dev error handler
[ 27.846596] sas: ata13: end_device-0:1:12: dev error handler
[ 27.846597] sas: ata15: end_device-0:1:14: dev error handler
[ 27.846613] sas: ata16: end_device-0:1:15: dev error handler
[ 27.846615] sas: ata17: end_device-0:1:16: dev error handler
[ 30.005465] ata14.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.005664] ata15.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.005666] ata15.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.005754] ata13.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.005755] ata13.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.005940] ata17.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.005941] ata17.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.006136] ata16.00: ATA-9: WDC WD60EFRX-68MYMN0, 82.00A82, max UDMA/133
[ 30.006136] ata16.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.006190] ata15.00: configured for UDMA/133
[ 30.006467] ata13.00: configured for UDMA/133
[ 30.006488] ata17.00: configured for UDMA/133
[ 30.006852] ata16.00: configured for UDMA/133
[ 30.085554] ata14.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.093334] ata14.00: configured for UDMA/133
[ 30.097796] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 30.100444] scsi 0:0:7:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.108801] scsi 0:0:8:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.117153] scsi 0:0:9:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.125503] scsi 0:0:10:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.133936] scsi 0:0:11:0: Direct-Access ATA WDC WD60EFRX-68M 82.0 PQ: 0 ANSI: 5
[ 30.142691] scsi 0:0:12:0: Enclosure LSI SAS2X28 0e12 PQ: 0 ANSI: 5
[ 30.152243] sas: REVALIDATING DOMAIN on port 0, pid:196
[ 30.155348] sas: Expander phy change count has changed
[ 30.158072] sas: ex 5003048001108c3f phy12 originated BROADCAST(CHANGE)
[ 30.158498] sas: ex 5003048001108c3f phy 0xc broadcast flutter
[ 30.158717] sas: ex 5003048001108c3f phy13 originated BROADCAST(CHANGE)
[ 30.159142] sas: ex 5003048001108c3f phy 0xd broadcast flutter
[ 30.159362] sas: ex 5003048001108c3f phy14 originated BROADCAST(CHANGE)
[ 30.159787] sas: ex 5003048001108c3f phy 0xe broadcast flutter
[ 30.159999] sas: ex 5003048001108c3f phy15 originated BROADCAST(CHANGE)
[ 30.160393] sas: ex 5003048001108c3f phy 0xf broadcast flutter
[ 30.160606] sas: ex 5003048001108c3f phy16 originated BROADCAST(CHANGE)
[ 30.161031] sas: ex 5003048001108c3f phy 0x10 broadcast flutter
[ 30.161243] sas: ex 5003048001108c3f phy17 originated BROADCAST(CHANGE)
[ 30.161667] sas: ex 5003048001108c3f phy 0x11 broadcast flutter
[ 30.165656] sas: done REVALIDATING DOMAIN on port 0, pid:196, res 0x0
[ 30.165677] sas: REVALIDATING DOMAIN on port 0, pid:196
[ 30.165721] sas: done REVALIDATING DOMAIN on port 0, pid:196, res 0x0
[ 30.165723] sas: broadcast received: 9
[ 30.165725] sas: broadcast received: 9
[ 30.165726] sas: broadcast received: 9
[ 30.165727] sas: broadcast received: 9
[ 30.165728] sas: REVALIDATING DOMAIN on port 1, pid:196
[ 30.165788] sd 0:0:0:0: [sdb] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.165792] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 30.165876] sd 0:0:1:0: Attached scsi generic sg2 type 0
[ 30.165890] sd 0:0:1:0: [sdc] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.165891] sd 0:0:1:0: [sdc] 4096-byte physical blocks
[ 30.165942] sd 0:0:1:0: [sdc] Write Protect is off
[ 30.165943] sd 0:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[ 30.165958] sd 0:0:2:0: [sdd] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.165960] sd 0:0:2:0: [sdd] 4096-byte physical blocks
[ 30.165961] sd 0:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.165965] sd 0:0:2:0: Attached scsi generic sg3 type 0
[ 30.165992] sd 0:0:2:0: [sdd] Write Protect is off
[ 30.165994] sd 0:0:2:0: [sdd] Mode Sense: 00 3a 00 00
[ 30.166013] sd 0:0:2:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166052] sd 0:0:3:0: [sde] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166053] sd 0:0:3:0: [sde] 4096-byte physical blocks
[ 30.166067] sd 0:0:3:0: Attached scsi generic sg4 type 0
[ 30.166093] sd 0:0:3:0: [sde] Write Protect is off
[ 30.166094] sd 0:0:3:0: [sde] Mode Sense: 00 3a 00 00
[ 30.166109] sd 0:0:3:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166147] sd 0:0:4:0: [sdf] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166148] sd 0:0:4:0: [sdf] 4096-byte physical blocks
[ 30.166165] sd 0:0:4:0: Attached scsi generic sg5 type 0
[ 30.166169] sd 0:0:4:0: [sdf] Write Protect is off
[ 30.166170] sd 0:0:4:0: [sdf] Mode Sense: 00 3a 00 00
[ 30.166180] sd 0:0:4:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166309] sd 0:0:5:0: Attached scsi generic sg6 type 0
[ 30.166319] sd 0:0:5:0: [sdg] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166320] sd 0:0:5:0: [sdg] 4096-byte physical blocks
[ 30.166334] sd 0:0:5:0: [sdg] Write Protect is off
[ 30.166334] sd 0:0:5:0: [sdg] Mode Sense: 00 3a 00 00
[ 30.166340] sd 0:0:5:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166415] scsi 0:0:6:0: Attached scsi generic sg7 type 13
[ 30.166520] sd 0:0:7:0: Attached scsi generic sg8 type 0
[ 30.166527] sd 0:0:7:0: [sdh] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166528] sd 0:0:7:0: [sdh] 4096-byte physical blocks
[ 30.166556] sd 0:0:7:0: [sdh] Write Protect is off
[ 30.166557] sd 0:0:7:0: [sdh] Mode Sense: 00 3a 00 00
[ 30.166567] sd 0:0:7:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166597] sd 0:0:8:0: [sdi] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166598] sd 0:0:8:0: [sdi] 4096-byte physical blocks
[ 30.166612] sd 0:0:8:0: [sdi] Write Protect is off
[ 30.166613] sd 0:0:8:0: [sdi] Mode Sense: 00 3a 00 00
[ 30.166618] sd 0:0:8:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166625] sd 0:0:8:0: Attached scsi generic sg9 type 0
[ 30.166720] sd 0:0:9:0: [sdj] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166721] sd 0:0:9:0: [sdj] 4096-byte physical blocks
[ 30.166734] sd 0:0:9:0: [sdj] Write Protect is off
[ 30.166734] sd 0:0:9:0: [sdj] Mode Sense: 00 3a 00 00
[ 30.166740] sd 0:0:9:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166746] sd 0:0:9:0: Attached scsi generic sg10 type 0
[ 30.166840] sd 0:0:10:0: [sdk] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166841] sd 0:0:10:0: [sdk] 4096-byte physical blocks
[ 30.166854] sd 0:0:10:0: [sdk] Write Protect is off
[ 30.166855] sd 0:0:10:0: [sdk] Mode Sense: 00 3a 00 00
[ 30.166859] sd 0:0:10:0: Attached scsi generic sg11 type 0
[ 30.166860] sd 0:0:10:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.166953] sd 0:0:11:0: [sdl] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[ 30.166954] sd 0:0:11:0: [sdl] 4096-byte physical blocks
[ 30.166971] sd 0:0:11:0: Attached scsi generic sg12 type 0
[ 30.166975] sd 0:0:11:0: [sdl] Write Protect is off
[ 30.166977] sd 0:0:11:0: [sdl] Mode Sense: 00 3a 00 00
[ 30.166985] sd 0:0:11:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.167085] scsi 0:0:12:0: Attached scsi generic sg13 type 13
[ 30.168007] sas: Expander phy change count has changed
[ 30.170193] sas: ex 50030480010f713f phy12 originated BROADCAST(CHANGE)
[ 30.170535] sas: ex 50030480010f713f phy 0xc broadcast flutter
[ 30.170704] sas: ex 50030480010f713f phy13 originated BROADCAST(CHANGE)
[ 30.171043] sas: ex 50030480010f713f phy 0xd broadcast flutter
[ 30.171211] sas: ex 50030480010f713f phy14 originated BROADCAST(CHANGE)
[ 30.171549] sas: ex 50030480010f713f phy 0xe broadcast flutter
[ 30.171717] sas: ex 50030480010f713f phy15 originated BROADCAST(CHANGE)
[ 30.172055] sas: ex 50030480010f713f phy 0xf broadcast flutter
[ 30.172224] sas: ex 50030480010f713f phy16 originated BROADCAST(CHANGE)
[ 30.172562] sas: ex 50030480010f713f phy 0x10 broadcast flutter
[ 30.174785] sas: done REVALIDATING DOMAIN on port 1, pid:196, res 0x0
[ 30.517279] sd 0:0:0:0: [sdb] 4096-byte physical blocks
[ 30.522591] sd 0:0:0:0: [sdb] Write Protect is off
[ 30.527452] sd 0:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 30.527458] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.899582] random: nonblocking pool is initialized
[ 30.932613] sdj: sdj1
[ 30.935171] sd 0:0:9:0: [sdj] Attached SCSI disk
[ 30.938259] sdd: sdd1
[ 30.938606] sd 0:0:2:0: [sdd] Attached SCSI disk
[ 30.944896] sdh: sdh1
[ 30.945162] sd 0:0:7:0: [sdh] Attached SCSI disk
[ 30.960954] sdf: sdf1
[ 30.961969] sdc: sdc1
[ 30.962317] sd 0:0:1:0: [sdc] Attached SCSI disk
[ 30.966518] sdk: sdk1
[ 30.966573] sde: sde1
[ 30.966739] sd 0:0:10:0: [sdk] Attached SCSI disk
[ 30.966767] sd 0:0:3:0: [sde] Attached SCSI disk
[ 30.969636] sdg: sdg1
[ 30.969813] sd 0:0:5:0: [sdg] Attached SCSI disk
[ 30.975786] sdi: sdi1
[ 30.975897] sd 0:0:8:0: [sdi] Attached SCSI disk
[ 30.987891] sdl: sdl1
[ 30.988178] sd 0:0:11:0: [sdl] Attached SCSI disk
[ 31.006364] sd 0:0:4:0: [sdf] Attached SCSI disk
[ 31.333034] sdb: sdb1
[ 31.335677] sd 0:0:0:0: [sdb] Attached SCSI disk
[ 31.403662] ses 0:0:6:0: Attached Enclosure device
[ 31.408541] ses 0:0:12:0: Attached Enclosure device
[ 31.436012] md: bind<sdg1>
[ 31.439935] md: bind<sdd1>
[ 31.443739] md: bind<sdi1>
[ 31.447863] md: bind<sdh1>
[ 31.452255] md: bind<sdc1>
[ 31.456800] md: bind<sde1>
[ 31.461230] md: bind<sdf1>
[ 31.466009] md: bind<sdb1>
[ 31.470873] md: bind<sdk1>
[ 31.475718] md: bind<sdl1>
[ 31.480867] md: bind<sdj1>
[ 31.486034] md/raid:md127: device sdj1 operational as raid disk 8
[ 31.492205] md/raid:md127: device sdk1 operational as raid disk 9
[ 31.498365] md/raid:md127: device sdb1 operational as raid disk 0
[ 31.504520] md/raid:md127: device sdf1 operational as raid disk 4
[ 31.510676] md/raid:md127: device sde1 operational as raid disk 3
[ 31.516834] md/raid:md127: device sdc1 operational as raid disk 1
[ 31.522991] md/raid:md127: device sdh1 operational as raid disk 6
[ 31.529151] md/raid:md127: device sdi1 operational as raid disk 7
[ 31.535310] md/raid:md127: device sdd1 operational as raid disk 2
[ 31.541465] md/raid:md127: device sdg1 operational as raid disk 5
[ 31.547990] md/raid:md127: allocated 0kB
[ 31.552036] md/raid:md127: raid level 6 active with 10 out of 10 devices, algorithm 2
[ 31.568972] RAID conf printout:
[ 31.568973] --- level:6 rd:10 wd:10
[ 31.568974] disk 0, o:1, dev:sdb1
[ 31.568975] disk 1, o:1, dev:sdc1
[ 31.568975] disk 2, o:1, dev:sdd1
[ 31.568976] disk 3, o:1, dev:sde1
[ 31.568976] disk 4, o:1, dev:sdf1
[ 31.568977] disk 5, o:1, dev:sdg1
[ 31.568977] disk 6, o:1, dev:sdh1
[ 31.568978] disk 7, o:1, dev:sdi1
[ 31.568978] disk 8, o:1, dev:sdj1
[ 31.568979] disk 9, o:1, dev:sdk1
[ 31.568991] md127: detected capacity change from 0 to 47998917148672
[ 31.605268] md127: unknown partition table
[ 31.783548] bio: create slab <bio-1> at 1
[ 32.154351] init: plymouth-upstart-bridge main process (298) terminated with status 1
[ 32.162329] init: plymouth-upstart-bridge main process ended, respawning
[ 32.172180] init: plymouth-upstart-bridge main process (308) terminated with status 1
[ 32.180113] init: plymouth-upstart-bridge main process ended, respawning
[ 32.189575] init: plymouth-upstart-bridge main process (316) terminated with status 1
[ 32.197517] init: plymouth-upstart-bridge main process ended, respawning
[ 32.205839] init: plymouth-upstart-bridge main process (321) terminated with status 1
[ 32.213809] init: plymouth-upstart-bridge main process ended, respawning
[ 32.304552] Adding 16733180k swap on /dev/sda5. Priority:-1 extents:1 across:16733180k SSFS
[ 32.321301] IPv6: ADDRCONF(NETDEV_UP): em1: link is not ready
[ 32.321305] IPv6: ADDRCONF(NETDEV_UP): em2: link is not ready
[ 32.338681] systemd-udevd[428]: starting version 204
[ 32.357558] lp: driver loaded but no devices found
[ 32.368153] IPMI System Interface driver.
[ 32.368171] ipmi_si: probing via ACPI
[ 32.368186] ipmi_si 00:0c: [io 0x0ca2] regsize 1 spacing 1 irq 0
[ 32.368187] ipmi_si: Adding ACPI-specified kcs state machine
[ 32.368195] ipmi_si: probing via SMBIOS
[ 32.368196] ipmi_si: SMBIOS: io 0xca2 regsize 1 spacing 1 irq 0
[ 32.368196] ipmi_si: Adding SMBIOS-specified kcs state machine duplicate interface
[ 32.368197] ipmi_si: probing via SPMI
[ 32.368198] ipmi_si: SPMI: io 0xca2 regsize 1 spacing 1 irq 0
[ 32.368199] ipmi_si: Adding SPMI-specified kcs state machine duplicate interface
[ 32.368200] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
[ 32.415453] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 32.418138] ACPI Warning: 0x0000000000001828-0x000000000000182f SystemIO conflicts with Region \PMIO 1 (20131115/utaddress-251)
[ 32.418142] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 32.418145] ACPI Warning: 0x0000000000001c30-0x0000000000001c3f SystemIO conflicts with Region \GPRL 1 (20131115/utaddress-251)
[ 32.418147] ACPI Warning: 0x0000000000001c30-0x0000000000001c3f SystemIO conflicts with Region \GPR_ 2 (20131115/utaddress-251)
[ 32.418149] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 32.418150] ACPI Warning: 0x0000000000001c00-0x0000000000001c2f SystemIO conflicts with Region \GPRL 1 (20131115/utaddress-251)
[ 32.418151] ACPI Warning: 0x0000000000001c00-0x0000000000001c2f SystemIO conflicts with Region \GPR_ 2 (20131115/utaddress-251)
[ 32.418153] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 32.418154] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 32.420762] cfg80211: Calling CRDA to update world regulatory domain
[ 32.478236] ipmi_si 00:0c: Found new BMC (man_id: 0x002a7c, prod_id: 0x0801, dev_id: 0x20)
[ 32.478239] ipmi_si 00:0c: IPMI kcs interface initialized
[ 32.597956] usb 3-1: reset high-speed USB device number 2 using xhci_hcd
[ 32.624825] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f840
[ 32.624827] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f800
[ 32.624828] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f880
[ 32.624829] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f8c0
[ 32.624830] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f900
[ 32.624831] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f940
[ 32.624832] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880408f7f980
[ 32.625132] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0502 detected
[ 32.634683] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5370 detected
[ 32.643264] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 32.643458] usbcore: registered new interface driver rt2800usb
[ 32.884598] sd 0:0:5:0: [sdg] command ffff880404ebd700 timed out
[ 32.884681] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.884684] sas: ata12: end_device-0:0:17: cmd error handler
[ 32.884695] sas: ata7: end_device-0:0:12: dev error handler
[ 32.884704] sas: ata8: end_device-0:0:13: dev error handler
[ 32.884708] sas: ata9: end_device-0:0:14: dev error handler
[ 32.884712] sas: ata10: end_device-0:0:15: dev error handler
[ 32.884717] sas: ata11: end_device-0:0:16: dev error handler
[ 32.884720] sas: ata12: end_device-0:0:17: dev error handler
[ 32.884728] sas: ata13: end_device-0:1:12: dev error handler
[ 32.884731] sas: ata14: end_device-0:1:13: dev error handler
[ 32.884735] sas: ata15: end_device-0:1:14: dev error handler
[ 32.884738] sas: ata16: end_device-0:1:15: dev error handler
[ 32.884741] sas: ata17: end_device-0:1:16: dev error handler
[ 32.884747] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.884896] sd 0:0:11:0: [sdl] command ffff8800d954ec00 timed out
[ 32.885205] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.885207] sas: ata17: end_device-0:1:16: cmd error handler
[ 32.885215] sas: ata7: end_device-0:0:12: dev error handler
[ 32.885221] sas: ata8: end_device-0:0:13: dev error handler
[ 32.885225] sas: ata9: end_device-0:0:14: dev error handler
[ 32.885228] sas: ata10: end_device-0:0:15: dev error handler
[ 32.885231] sas: ata11: end_device-0:0:16: dev error handler
[ 32.885234] sas: ata12: end_device-0:0:17: dev error handler
[ 32.885238] sas: ata13: end_device-0:1:12: dev error handler
[ 32.885241] sas: ata14: end_device-0:1:13: dev error handler
[ 32.885244] sas: ata15: end_device-0:1:14: dev error handler
[ 32.885247] sas: ata16: end_device-0:1:15: dev error handler
[ 32.885250] sas: ata17: end_device-0:1:16: dev error handler
[ 32.885259] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.885515] sd 0:0:7:0: [sdh] command ffff8800d954eb00 timed out
[ 32.885742] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.885744] sas: ata13: end_device-0:1:12: cmd error handler
[ 32.885751] sas: ata7: end_device-0:0:12: dev error handler
[ 32.885756] sas: ata8: end_device-0:0:13: dev error handler
[ 32.885759] sas: ata9: end_device-0:0:14: dev error handler
[ 32.885761] sas: ata10: end_device-0:0:15: dev error handler
[ 32.885764] sas: ata11: end_device-0:0:16: dev error handler
[ 32.885767] sas: ata12: end_device-0:0:17: dev error handler
[ 32.885769] sas: ata13: end_device-0:1:12: dev error handler
[ 32.885775] sas: ata14: end_device-0:1:13: dev error handler
[ 32.885778] sas: ata15: end_device-0:1:14: dev error handler
[ 32.885780] sas: ata16: end_device-0:1:15: dev error handler
[ 32.885783] sas: ata17: end_device-0:1:16: dev error handler
[ 32.885787] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.885946] sd 0:0:1:0: [sdc] command ffff880404e68f00 timed out
[ 32.885984] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.885986] sas: ata8: end_device-0:0:13: cmd error handler
[ 32.885993] sas: ata7: end_device-0:0:12: dev error handler
[ 32.885998] sas: ata8: end_device-0:0:13: dev error handler
[ 32.886005] sas: ata9: end_device-0:0:14: dev error handler
[ 32.886007] sas: ata10: end_device-0:0:15: dev error handler
[ 32.886009] sas: ata11: end_device-0:0:16: dev error handler
[ 32.886010] sas: ata12: end_device-0:0:17: dev error handler
[ 32.886012] sas: ata13: end_device-0:1:12: dev error handler
[ 32.886013] sas: ata14: end_device-0:1:13: dev error handler
[ 32.886014] sas: ata15: end_device-0:1:14: dev error handler
[ 32.886017] sas: ata16: end_device-0:1:15: dev error handler
[ 32.886019] sas: ata17: end_device-0:1:16: dev error handler
[ 32.886023] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.886335] sd 0:0:2:0: [sdd] command ffff8804068d0600 timed out
[ 32.886485] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.886487] sas: ata9: end_device-0:0:14: cmd error handler
[ 32.886495] sas: ata7: end_device-0:0:12: dev error handler
[ 32.886498] sas: ata8: end_device-0:0:13: dev error handler
[ 32.886501] sas: ata9: end_device-0:0:14: dev error handler
[ 32.886502] sas: ata10: end_device-0:0:15: dev error handler
[ 32.886505] sas: ata11: end_device-0:0:16: dev error handler
[ 32.886508] sas: ata12: end_device-0:0:17: dev error handler
[ 32.886509] sas: ata13: end_device-0:1:12: dev error handler
[ 32.886512] sas: ata14: end_device-0:1:13: dev error handler
[ 32.886512] sas: ata15: end_device-0:1:14: dev error handler
[ 32.886515] sas: ata16: end_device-0:1:15: dev error handler
[ 32.886516] sas: ata17: end_device-0:1:16: dev error handler
[ 32.886520] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.886883] sd 0:0:3:0: [sde] command ffff880404107500 timed out
[ 32.887002] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.887004] sas: ata10: end_device-0:0:15: cmd error handler
[ 32.887012] sas: ata7: end_device-0:0:12: dev error handler
[ 32.887019] sas: ata8: end_device-0:0:13: dev error handler
[ 32.887023] sas: ata9: end_device-0:0:14: dev error handler
[ 32.887026] sas: ata10: end_device-0:0:15: dev error handler
[ 32.887032] sas: ata11: end_device-0:0:16: dev error handler
[ 32.887035] sas: ata12: end_device-0:0:17: dev error handler
[ 32.887038] sas: ata13: end_device-0:1:12: dev error handler
[ 32.887040] sas: ata14: end_device-0:1:13: dev error handler
[ 32.887043] sas: ata15: end_device-0:1:14: dev error handler
[ 32.887045] sas: ata16: end_device-0:1:15: dev error handler
[ 32.887047] sas: ata17: end_device-0:1:16: dev error handler
[ 32.887072] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.888071] type=1400 audit(1409953734.556:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=630 comm="apparmor_parser"
[ 32.888076] type=1400 audit(1409953734.556:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=630 comm="apparmor_parser"
[ 32.888079] type=1400 audit(1409953734.556:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=630 comm="apparmor_parser"
[ 32.888201] type=1400 audit(1409953734.556:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=632 comm="apparmor_parser"
[ 32.888207] type=1400 audit(1409953734.556:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=632 comm="apparmor_parser"
[ 32.888211] type=1400 audit(1409953734.556:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=632 comm="apparmor_parser"
[ 32.888423] type=1400 audit(1409953734.556:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=630 comm="apparmor_parser"
[ 32.888428] type=1400 audit(1409953734.556:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=630 comm="apparmor_parser"
[ 32.888565] type=1400 audit(1409953734.556:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=632 comm="apparmor_parser"
[ 32.888570] type=1400 audit(1409953734.556:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=632 comm="apparmor_parser"
[ 32.890963] cfg80211: World regulatory domain updated:
[ 32.890965] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 32.890967] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.890968] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.890969] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 32.890970] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.890971] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.893664] [drm] Initialized drm 1.1.0 20060810
[ 32.894582] sd 0:0:0:0: [sdb] command ffff880409385200 timed out
[ 32.894591] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.894594] sas: ata7: end_device-0:0:12: cmd error handler
[ 32.894600] sas: ata7: end_device-0:0:12: dev error handler
[ 32.894612] sas: ata8: end_device-0:0:13: dev error handler
[ 32.894616] sas: ata9: end_device-0:0:14: dev error handler
[ 32.894620] sas: ata10: end_device-0:0:15: dev error handler
[ 32.894624] sas: ata11: end_device-0:0:16: dev error handler
[ 32.894627] sas: ata12: end_device-0:0:17: dev error handler
[ 32.894631] sas: ata13: end_device-0:1:12: dev error handler
[ 32.894635] sas: ata14: end_device-0:1:13: dev error handler
[ 32.894638] sas: ata15: end_device-0:1:14: dev error handler
[ 32.894642] sas: ata16: end_device-0:1:15: dev error handler
[ 32.894645] sas: ata17: end_device-0:1:16: dev error handler
[ 32.894651] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.900183] sd 0:0:9:0: [sdj] command ffff8804078c8400 timed out
[ 32.900192] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.900194] sas: ata15: end_device-0:1:14: cmd error handler
[ 32.900372] sas: ata7: end_device-0:0:12: dev error handler
[ 32.900375] sas: ata8: end_device-0:0:13: dev error handler
[ 32.900380] sas: ata9: end_device-0:0:14: dev error handler
[ 32.900381] sas: ata10: end_device-0:0:15: dev error handler
[ 32.900383] sas: ata11: end_device-0:0:16: dev error handler
[ 32.900384] sas: ata12: end_device-0:0:17: dev error handler
[ 32.900386] sas: ata13: end_device-0:1:12: dev error handler
[ 32.900388] sas: ata14: end_device-0:1:13: dev error handler
[ 32.900389] sas: ata15: end_device-0:1:14: dev error handler
[ 32.900392] sas: ata16: end_device-0:1:15: dev error handler
[ 32.900395] sas: ata17: end_device-0:1:16: dev error handler
[ 32.900400] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.900577] sd 0:0:8:0: [sdi] command ffff8800d9547000 timed out
[ 32.900706] sd 0:0:4:0: [sdf] command ffff8800364d6b00 timed out
[ 32.900869] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 32.900871] sas: ata14: end_device-0:1:13: cmd error handler
[ 32.900872] sas: ata11: end_device-0:0:16: cmd error handler
[ 32.900879] sas: ata7: end_device-0:0:12: dev error handler
[ 32.900884] sas: ata8: end_device-0:0:13: dev error handler
[ 32.900887] sas: ata9: end_device-0:0:14: dev error handler
[ 32.900890] sas: ata10: end_device-0:0:15: dev error handler
[ 32.900895] sas: ata11: end_device-0:0:16: dev error handler
[ 32.900898] sas: ata12: end_device-0:0:17: dev error handler
[ 32.900903] sas: ata13: end_device-0:1:12: dev error handler
[ 32.900904] sas: ata14: end_device-0:1:13: dev error handler
[ 32.900905] sas: ata15: end_device-0:1:14: dev error handler
[ 32.900908] sas: ata16: end_device-0:1:15: dev error handler
[ 32.900909] sas: ata17: end_device-0:1:16: dev error handler
[ 32.900915] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.901207] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 32.903842] sd 0:0:10:0: [sdk] command ffff880404efc500 timed out
[ 32.903850] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 32.903852] sas: ata16: end_device-0:1:15: cmd error handler
[ 32.903861] sas: ata7: end_device-0:0:12: dev error handler
[ 32.903870] sas: ata8: end_device-0:0:13: dev error handler
[ 32.903874] sas: ata9: end_device-0:0:14: dev error handler
[ 32.903878] sas: ata10: end_device-0:0:15: dev error handler
[ 32.903881] sas: ata11: end_device-0:0:16: dev error handler
[ 32.903885] sas: ata12: end_device-0:0:17: dev error handler
[ 32.903889] sas: ata13: end_device-0:1:12: dev error handler
[ 32.903892] sas: ata14: end_device-0:1:13: dev error handler
[ 32.903895] sas: ata15: end_device-0:1:14: dev error handler
[ 32.903899] sas: ata16: end_device-0:1:15: dev error handler
[ 32.903906] sas: ata17: end_device-0:1:16: dev error handler
[ 32.903912] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 32.936768] init: udev-fallback-graphics main process (742) terminated with status 1
[ 33.014661] e1000e 0000:00:19.0: irq 47 for MSI/MSI-X
[ 33.117298] e1000e 0000:00:19.0: irq 47 for MSI/MSI-X
[ 33.117409] IPv6: ADDRCONF(NETDEV_UP): em2: link is not ready
[ 33.134955] init: Failed to obtain startpar-bridge instance: Unknown parameter: INSTANCE
[ 33.590145] RAID conf printout:
[ 33.590149] --- level:6 rd:10 wd:10
[ 33.590151] disk 0, o:1, dev:sdb1
[ 33.590152] disk 1, o:1, dev:sdc1
[ 33.590152] disk 2, o:1, dev:sdd1
[ 33.590153] disk 3, o:1, dev:sde1
[ 33.590154] disk 4, o:1, dev:sdf1
[ 33.590155] disk 5, o:1, dev:sdg1
[ 33.590155] disk 6, o:1, dev:sdh1
[ 33.590156] disk 7, o:1, dev:sdi1
[ 33.590157] disk 8, o:1, dev:sdj1
[ 33.590158] disk 9, o:1, dev:sdk1
[ 33.725096] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: errors=continue
[ 33.740684] FS-Cache: Loaded
[ 33.744773] RPC: Registered named UNIX socket transport module.
[ 33.744775] RPC: Registered udp transport module.
[ 33.744775] RPC: Registered tcp transport module.
[ 33.744776] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 33.751333] FS-Cache: Netfs 'nfs' registered for caching
[ 33.757318] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 33.768107] init: failsafe main process (1041) killed by TERM signal
[ 34.050996] ipmi device interface
[ 34.186362] init: plymouth-upstart-bridge main process ended, respawning
[ 36.783537] e1000e: em2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 36.783567] IPv6: ADDRCONF(NETDEV_CHANGE): em2: link becomes ready
[ 130.814661] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.814661]
[ 130.814664] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.814666] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 130.814667] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=303 CI=302
[ 130.815159] pm80xx pm8001_mpi_msg_consume 1450:: CI=318 PI=319 msgHeader=8100200d
[ 130.815161] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.815162] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.815164] pm80xx pm8001_mpi_msg_free_set 1407: CI=319 PI=319
[ 130.815178] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.815178]
[ 130.815179] pm80xx pm80xx_chip_sata_req 4105:no data
[ 130.815180] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 130.815181] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=304 CI=303
[ 130.815273] pm80xx pm8001_mpi_msg_consume 1450:: CI=319 PI=320 msgHeader=8100200d
[ 130.815274] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.815275] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.815276] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 130.815287] pm80xx mpi_sata_completion 2090:other len = 20
[ 130.815288] pm80xx pm8001_mpi_msg_free_set 1407: CI=320 PI=320
[ 130.815298] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.815298]
[ 130.815298] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.815299] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 130.815300] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=305 CI=304
[ 130.815741] pm80xx pm8001_mpi_msg_consume 1450:: CI=320 PI=321 msgHeader=8100200d
[ 130.815742] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.815743] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.815755] pm80xx pm8001_mpi_msg_free_set 1407: CI=321 PI=321
[ 130.820126] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.820126]
[ 130.820127] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.820128] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.820129] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=306 CI=305
[ 130.823365] pm80xx pm8001_mpi_msg_consume 1450:: CI=321 PI=322 msgHeader=8100200d
[ 130.823369] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.823371] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.823381] pm80xx pm8001_mpi_msg_free_set 1407: CI=322 PI=322
[ 130.823442] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.823442]
[ 130.823445] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.823447] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.823449] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=307 CI=306
[ 130.826791] pm80xx pm8001_mpi_msg_consume 1450:: CI=322 PI=323 msgHeader=8100200d
[ 130.826794] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.826795] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.826799] pm80xx pm8001_mpi_msg_free_set 1407: CI=323 PI=323
[ 130.826830] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.826830]
[ 130.826831] pm80xx pm80xx_chip_sata_req 4105:no data
[ 130.826832] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.826833] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=308 CI=307
[ 130.869586] pm80xx pm8001_mpi_msg_consume 1450:: CI=323 PI=324 msgHeader=8100200d
[ 130.869588] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.869589] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.869590] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 130.869591] pm80xx mpi_sata_completion 2090:other len = 20
[ 130.869595] pm80xx pm8001_mpi_msg_free_set 1407: CI=324 PI=324
[ 130.869712] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.869712]
[ 130.869713] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.869714] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.869715] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=309 CI=308
[ 130.869936] pm80xx pm8001_mpi_msg_consume 1450:: CI=324 PI=325 msgHeader=8100200d
[ 130.869938] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.869939] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.869943] pm80xx pm8001_mpi_msg_free_set 1407: CI=325 PI=325
[ 130.869972] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.869972]
[ 130.869974] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.869975] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.869977] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=310 CI=309
[ 130.870276] pm80xx pm8001_mpi_msg_consume 1450:: CI=325 PI=326 msgHeader=8100200d
[ 130.870278] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.870279] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.870283] pm80xx pm8001_mpi_msg_free_set 1407: CI=326 PI=326
[ 130.870316] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.870316]
[ 130.870317] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.870318] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.870320] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=311 CI=310
[ 130.870623] pm80xx pm8001_mpi_msg_consume 1450:: CI=326 PI=327 msgHeader=8100200d
[ 130.870625] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.870626] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.870630] pm80xx pm8001_mpi_msg_free_set 1407: CI=327 PI=327
[ 130.870656] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 130.870656]
[ 130.870657] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 130.870658] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 130.870659] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=312 CI=311
[ 130.870923] pm80xx pm8001_mpi_msg_consume 1450:: CI=327 PI=328 msgHeader=8100200d
[ 130.870925] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 130.870926] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 130.870930] pm80xx pm8001_mpi_msg_free_set 1407: CI=328 PI=328
[ 132.070555] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.070555]
[ 132.070558] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.070559] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.070561] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=313 CI=312
[ 132.071042] pm80xx pm8001_mpi_msg_consume 1450:: CI=328 PI=329 msgHeader=8100200d
[ 132.071045] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.071046] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.071051] pm80xx pm8001_mpi_msg_free_set 1407: CI=329 PI=329
[ 132.071091] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.071091]
[ 132.071093] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.071094] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.071095] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=314 CI=313
[ 132.071162] pm80xx pm8001_mpi_msg_consume 1450:: CI=329 PI=330 msgHeader=8100200d
[ 132.071164] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.071165] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.071166] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.071167] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.071170] pm80xx pm8001_mpi_msg_free_set 1407: CI=330 PI=330
[ 132.071182] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.071182]
[ 132.071183] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.071184] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.071185] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=315 CI=314
[ 132.071639] pm80xx pm8001_mpi_msg_consume 1450:: CI=330 PI=331 msgHeader=8100200d
[ 132.071641] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.071642] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.071646] pm80xx pm8001_mpi_msg_free_set 1407: CI=331 PI=331
[ 132.075952] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.075952]
[ 132.075954] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.075955] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.075956] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=316 CI=315
[ 132.079180] pm80xx pm8001_mpi_msg_consume 1450:: CI=331 PI=332 msgHeader=8100200d
[ 132.079182] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.079183] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.079187] pm80xx pm8001_mpi_msg_free_set 1407: CI=332 PI=332
[ 132.079215] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.079215]
[ 132.079217] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.079218] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.079220] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=317 CI=316
[ 132.082638] pm80xx pm8001_mpi_msg_consume 1450:: CI=332 PI=333 msgHeader=8100200d
[ 132.082640] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.082641] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.082645] pm80xx pm8001_mpi_msg_free_set 1407: CI=333 PI=333
[ 132.089977] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.089977]
[ 132.089979] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.089980] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.089981] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=318 CI=317
[ 132.090467] pm80xx pm8001_mpi_msg_consume 1450:: CI=333 PI=334 msgHeader=8100200d
[ 132.090469] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.090470] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.090473] pm80xx pm8001_mpi_msg_free_set 1407: CI=334 PI=334
[ 132.090499] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.090499]
[ 132.090501] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.090502] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.090504] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=319 CI=318
[ 132.090570] pm80xx pm8001_mpi_msg_consume 1450:: CI=334 PI=335 msgHeader=8100200d
[ 132.090572] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.090573] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.090574] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.090574] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.090578] pm80xx pm8001_mpi_msg_free_set 1407: CI=335 PI=335
[ 132.090589] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.090589]
[ 132.090589] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.090590] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.090591] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=320 CI=319
[ 132.091037] pm80xx pm8001_mpi_msg_consume 1450:: CI=335 PI=336 msgHeader=8100200d
[ 132.091039] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.091040] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.091044] pm80xx pm8001_mpi_msg_free_set 1407: CI=336 PI=336
[ 132.095302] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.095302]
[ 132.095303] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.095304] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.095306] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=321 CI=320
[ 132.098440] pm80xx pm8001_mpi_msg_consume 1450:: CI=336 PI=337 msgHeader=8100200d
[ 132.098443] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.098444] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.098449] pm80xx pm8001_mpi_msg_free_set 1407: CI=337 PI=337
[ 132.098478] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.098478]
[ 132.098480] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.098482] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.098484] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=322 CI=321
[ 132.101844] pm80xx pm8001_mpi_msg_consume 1450:: CI=337 PI=338 msgHeader=8100200d
[ 132.101846] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.101847] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.101850] pm80xx pm8001_mpi_msg_free_set 1407: CI=338 PI=338
[ 132.109109] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.109109]
[ 132.109111] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.109112] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.109113] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=323 CI=322
[ 132.109593] pm80xx pm8001_mpi_msg_consume 1450:: CI=338 PI=339 msgHeader=8100200d
[ 132.109595] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.109596] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.109599] pm80xx pm8001_mpi_msg_free_set 1407: CI=339 PI=339
[ 132.109611] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.109611]
[ 132.109611] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.109612] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.109613] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=324 CI=323
[ 132.109684] pm80xx pm8001_mpi_msg_consume 1450:: CI=339 PI=340 msgHeader=8100200d
[ 132.109686] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.109687] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.109687] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.109688] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.109692] pm80xx pm8001_mpi_msg_free_set 1407: CI=340 PI=340
[ 132.109710] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.109710]
[ 132.109711] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.109711] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.109712] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=325 CI=324
[ 132.110143] pm80xx pm8001_mpi_msg_consume 1450:: CI=340 PI=341 msgHeader=8100200d
[ 132.110145] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.110146] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.110159] pm80xx pm8001_mpi_msg_free_set 1407: CI=341 PI=341
[ 132.114461] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.114461]
[ 132.114462] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.114463] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.114464] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=326 CI=325
[ 132.117636] pm80xx pm8001_mpi_msg_consume 1450:: CI=341 PI=342 msgHeader=8100200d
[ 132.117638] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.117639] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.117644] pm80xx pm8001_mpi_msg_free_set 1407: CI=342 PI=342
[ 132.117657] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.117657]
[ 132.117658] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.117659] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.117660] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=327 CI=326
[ 132.121034] pm80xx pm8001_mpi_msg_consume 1450:: CI=342 PI=343 msgHeader=8100200d
[ 132.121036] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.121037] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.121041] pm80xx pm8001_mpi_msg_free_set 1407: CI=343 PI=343
[ 132.128346] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.128346]
[ 132.128348] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.128349] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.128350] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=328 CI=327
[ 132.128822] pm80xx pm8001_mpi_msg_consume 1450:: CI=343 PI=344 msgHeader=8100200d
[ 132.128824] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.128825] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.128828] pm80xx pm8001_mpi_msg_free_set 1407: CI=344 PI=344
[ 132.128860] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.128860]
[ 132.128861] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.128862] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.128863] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=329 CI=328
[ 132.128946] pm80xx pm8001_mpi_msg_consume 1450:: CI=344 PI=345 msgHeader=8100200d
[ 132.128947] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.128948] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.128949] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.128950] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.128953] pm80xx pm8001_mpi_msg_free_set 1407: CI=345 PI=345
[ 132.128974] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.128974]
[ 132.128985] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.128986] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.128987] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=330 CI=329
[ 132.129469] pm80xx pm8001_mpi_msg_consume 1450:: CI=345 PI=346 msgHeader=8100200d
[ 132.129471] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.129472] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.129476] pm80xx pm8001_mpi_msg_free_set 1407: CI=346 PI=346
[ 132.133809] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.133809]
[ 132.133810] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.133811] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.133812] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=331 CI=330
[ 132.136997] pm80xx pm8001_mpi_msg_consume 1450:: CI=346 PI=347 msgHeader=8100200d
[ 132.136999] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.137000] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.137004] pm80xx pm8001_mpi_msg_free_set 1407: CI=347 PI=347
[ 132.137029] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.137029]
[ 132.137030] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.137031] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.137032] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=332 CI=331
[ 132.140465] pm80xx pm8001_mpi_msg_consume 1450:: CI=347 PI=348 msgHeader=8100200d
[ 132.140468] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.140470] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.140480] pm80xx pm8001_mpi_msg_free_set 1407: CI=348 PI=348
[ 132.148403] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.148403]
[ 132.148405] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.148406] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.148408] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=333 CI=332
[ 132.148892] pm80xx pm8001_mpi_msg_consume 1450:: CI=348 PI=349 msgHeader=8100200d
[ 132.148903] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.148904] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.148906] pm80xx pm8001_mpi_msg_free_set 1407: CI=349 PI=349
[ 132.148916] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.148916]
[ 132.148916] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.148917] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.148918] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=334 CI=333
[ 132.149014] pm80xx pm8001_mpi_msg_consume 1450:: CI=349 PI=350 msgHeader=8100200d
[ 132.149015] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.149016] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.149017] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.149028] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.149029] pm80xx pm8001_mpi_msg_free_set 1407: CI=350 PI=350
[ 132.149038] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.149038]
[ 132.149038] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.149039] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.149040] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=335 CI=334
[ 132.149483] pm80xx pm8001_mpi_msg_consume 1450:: CI=350 PI=351 msgHeader=8100200d
[ 132.149484] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.149485] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.149487] pm80xx pm8001_mpi_msg_free_set 1407: CI=351 PI=351
[ 132.153805] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.153805]
[ 132.153806] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.153808] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.153809] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=336 CI=335
[ 132.157043] pm80xx pm8001_mpi_msg_consume 1450:: CI=351 PI=352 msgHeader=8100200d
[ 132.157047] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.157048] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.157053] pm80xx pm8001_mpi_msg_free_set 1407: CI=352 PI=352
[ 132.157092] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.157092]
[ 132.157094] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.157096] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.157097] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=337 CI=336
[ 132.160472] pm80xx pm8001_mpi_msg_consume 1450:: CI=352 PI=353 msgHeader=8100200d
[ 132.160476] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.160477] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.160482] pm80xx pm8001_mpi_msg_free_set 1407: CI=353 PI=353
[ 132.168287] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.168287]
[ 132.168290] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.168291] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.168293] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=338 CI=337
[ 132.168758] pm80xx pm8001_mpi_msg_consume 1450:: CI=353 PI=354 msgHeader=8100200d
[ 132.168760] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.168761] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.168765] pm80xx pm8001_mpi_msg_free_set 1407: CI=354 PI=354
[ 132.168794] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.168794]
[ 132.168795] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.168796] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.168797] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=339 CI=338
[ 132.168869] pm80xx pm8001_mpi_msg_consume 1450:: CI=354 PI=355 msgHeader=8100200d
[ 132.168871] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.168872] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.168883] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.168884] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.168885] pm80xx pm8001_mpi_msg_free_set 1407: CI=355 PI=355
[ 132.168896] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.168896]
[ 132.168896] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.168897] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.168898] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=340 CI=339
[ 132.169335] pm80xx pm8001_mpi_msg_consume 1450:: CI=355 PI=356 msgHeader=8100200d
[ 132.169336] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.169337] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.169349] pm80xx pm8001_mpi_msg_free_set 1407: CI=356 PI=356
[ 132.173663] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.173663]
[ 132.173664] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.173665] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.173666] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=341 CI=340
[ 132.176832] pm80xx pm8001_mpi_msg_consume 1450:: CI=356 PI=357 msgHeader=8100200d
[ 132.176834] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.176835] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.176837] pm80xx pm8001_mpi_msg_free_set 1407: CI=357 PI=357
[ 132.176851] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.176851]
[ 132.176852] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.176853] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.176855] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=342 CI=341
[ 132.180212] pm80xx pm8001_mpi_msg_consume 1450:: CI=357 PI=358 msgHeader=8100200d
[ 132.180214] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.180215] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.180217] pm80xx pm8001_mpi_msg_free_set 1407: CI=358 PI=358
[ 132.187528] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.187528]
[ 132.187530] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.187531] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.187533] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=343 CI=342
[ 132.188016] pm80xx pm8001_mpi_msg_consume 1450:: CI=358 PI=359 msgHeader=8100200d
[ 132.188018] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.188019] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.188020] pm80xx pm8001_mpi_msg_free_set 1407: CI=359 PI=359
[ 132.188036] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.188036]
[ 132.188037] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.188038] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.188040] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=344 CI=343
[ 132.188122] pm80xx pm8001_mpi_msg_consume 1450:: CI=359 PI=360 msgHeader=8100200d
[ 132.188123] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.188124] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.188125] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.188136] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.188137] pm80xx pm8001_mpi_msg_free_set 1407: CI=360 PI=360
[ 132.188147] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.188147]
[ 132.188148] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.188149] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.188150] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=345 CI=344
[ 132.188583] pm80xx pm8001_mpi_msg_consume 1450:: CI=360 PI=361 msgHeader=8100200d
[ 132.188584] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.188585] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.188597] pm80xx pm8001_mpi_msg_free_set 1407: CI=361 PI=361
[ 132.192934] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.192934]
[ 132.192935] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.192936] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.192937] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=346 CI=345
[ 132.196116] pm80xx pm8001_mpi_msg_consume 1450:: CI=361 PI=362 msgHeader=8100200d
[ 132.196118] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.196120] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.196125] pm80xx pm8001_mpi_msg_free_set 1407: CI=362 PI=362
[ 132.196170] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.196170]
[ 132.196173] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.196174] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.196176] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=347 CI=346
[ 132.199506] pm80xx pm8001_mpi_msg_consume 1450:: CI=362 PI=363 msgHeader=8100200d
[ 132.199508] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.199509] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.199514] pm80xx pm8001_mpi_msg_free_set 1407: CI=363 PI=363
[ 132.207274] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.207274]
[ 132.207276] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.207277] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.207278] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=348 CI=347
[ 132.207743] pm80xx pm8001_mpi_msg_consume 1450:: CI=363 PI=364 msgHeader=8100200d
[ 132.207744] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.207744] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.207746] pm80xx pm8001_mpi_msg_free_set 1407: CI=364 PI=364
[ 132.207755] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.207755]
[ 132.207756] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.207757] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.207758] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=349 CI=348
[ 132.207814] pm80xx pm8001_mpi_msg_consume 1450:: CI=364 PI=365 msgHeader=8100200d
[ 132.207818] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.207821] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.207825] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.207828] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.207830] pm80xx pm8001_mpi_msg_free_set 1407: CI=365 PI=365
[ 132.207846] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.207846]
[ 132.207847] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.207849] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.207850] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=350 CI=349
[ 132.208342] pm80xx pm8001_mpi_msg_consume 1450:: CI=365 PI=366 msgHeader=8100200d
[ 132.208343] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.208344] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.208355] pm80xx pm8001_mpi_msg_free_set 1407: CI=366 PI=366
[ 132.212801] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.212801]
[ 132.212802] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.212803] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.212804] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=351 CI=350
[ 132.215950] pm80xx pm8001_mpi_msg_consume 1450:: CI=366 PI=367 msgHeader=8100200d
[ 132.215952] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.215963] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.215965] pm80xx pm8001_mpi_msg_free_set 1407: CI=367 PI=367
[ 132.215996] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.215996]
[ 132.215997] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.215999] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.216000] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=352 CI=351
[ 132.219333] pm80xx pm8001_mpi_msg_consume 1450:: CI=367 PI=368 msgHeader=8100200d
[ 132.219334] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.219336] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.219348] pm80xx pm8001_mpi_msg_free_set 1407: CI=368 PI=368
[ 132.226844] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.226844]
[ 132.226845] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.226847] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.226848] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=353 CI=352
[ 132.227328] pm80xx pm8001_mpi_msg_consume 1450:: CI=368 PI=369 msgHeader=8100200d
[ 132.227329] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.227340] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.227342] pm80xx pm8001_mpi_msg_free_set 1407: CI=369 PI=369
[ 132.227354] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.227354]
[ 132.227355] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.227355] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.227356] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=354 CI=353
[ 132.227410] pm80xx pm8001_mpi_msg_consume 1450:: CI=369 PI=370 msgHeader=8100200d
[ 132.227411] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.227412] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.227412] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.227413] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.227414] pm80xx pm8001_mpi_msg_free_set 1407: CI=370 PI=370
[ 132.227421] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.227421]
[ 132.227422] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.227422] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.227423] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=355 CI=354
[ 132.227858] pm80xx pm8001_mpi_msg_consume 1450:: CI=370 PI=371 msgHeader=8100200d
[ 132.227859] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.227860] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.227864] pm80xx pm8001_mpi_msg_free_set 1407: CI=371 PI=371
[ 132.232209] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.232209]
[ 132.232210] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.232211] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.232212] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=356 CI=355
[ 132.235376] pm80xx pm8001_mpi_msg_consume 1450:: CI=371 PI=372 msgHeader=8100200d
[ 132.235377] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.235388] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.235390] pm80xx pm8001_mpi_msg_free_set 1407: CI=372 PI=372
[ 132.235400] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.235400]
[ 132.235401] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.235402] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.235403] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=357 CI=356
[ 132.238731] pm80xx pm8001_mpi_msg_consume 1450:: CI=372 PI=373 msgHeader=8100200d
[ 132.238733] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.238734] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.238736] pm80xx pm8001_mpi_msg_free_set 1407: CI=373 PI=373
[ 132.246365] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.246365]
[ 132.246366] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.246367] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.246369] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=358 CI=357
[ 132.246833] pm80xx pm8001_mpi_msg_consume 1450:: CI=373 PI=374 msgHeader=8100200d
[ 132.246834] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.246835] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.246836] pm80xx pm8001_mpi_msg_free_set 1407: CI=374 PI=374
[ 132.246845] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.246845]
[ 132.246846] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.246846] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.246847] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=359 CI=358
[ 132.246938] pm80xx pm8001_mpi_msg_consume 1450:: CI=374 PI=375 msgHeader=8100200d
[ 132.246939] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.246940] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.246941] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.246951] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.246953] pm80xx pm8001_mpi_msg_free_set 1407: CI=375 PI=375
[ 132.246960] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.246960]
[ 132.246961] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.246962] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.246963] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=360 CI=359
[ 132.247392] pm80xx pm8001_mpi_msg_consume 1450:: CI=375 PI=376 msgHeader=8100200d
[ 132.247392] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.247393] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.247394] pm80xx pm8001_mpi_msg_free_set 1407: CI=376 PI=376
[ 132.251673] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.251673]
[ 132.251674] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.251675] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.251676] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=361 CI=360
[ 132.254843] pm80xx pm8001_mpi_msg_consume 1450:: CI=376 PI=377 msgHeader=8100200d
[ 132.254845] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.254846] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.254847] pm80xx pm8001_mpi_msg_free_set 1407: CI=377 PI=377
[ 132.254862] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.254862]
[ 132.254863] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.254864] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.254865] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=362 CI=361
[ 132.258254] pm80xx pm8001_mpi_msg_consume 1450:: CI=377 PI=378 msgHeader=8100200d
[ 132.258258] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.258260] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.258270] pm80xx pm8001_mpi_msg_free_set 1407: CI=378 PI=378
[ 132.266366] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.266366]
[ 132.266368] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.266370] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.266372] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=363 CI=362
[ 132.266857] pm80xx pm8001_mpi_msg_consume 1450:: CI=378 PI=379 msgHeader=8100200d
[ 132.266860] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.266861] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.266865] pm80xx pm8001_mpi_msg_free_set 1407: CI=379 PI=379
[ 132.266892] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.266892]
[ 132.266893] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.266894] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.266895] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=364 CI=363
[ 132.266963] pm80xx pm8001_mpi_msg_consume 1450:: CI=379 PI=380 msgHeader=8100200d
[ 132.266965] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.266966] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.266967] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.266968] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.266972] pm80xx pm8001_mpi_msg_free_set 1407: CI=380 PI=380
[ 132.266982] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.266982]
[ 132.266984] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.266987] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.266988] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=365 CI=364
[ 132.267438] pm80xx pm8001_mpi_msg_consume 1450:: CI=380 PI=381 msgHeader=8100200d
[ 132.267440] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.267440] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.267444] pm80xx pm8001_mpi_msg_free_set 1407: CI=381 PI=381
[ 132.271755] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.271755]
[ 132.271756] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.271757] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.271758] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=366 CI=365
[ 132.274567] pm80xx pm8001_mpi_msg_consume 1450:: CI=381 PI=382 msgHeader=8100200d
[ 132.274569] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.274570] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.274574] pm80xx pm8001_mpi_msg_free_set 1407: CI=382 PI=382
[ 132.274597] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.274597]
[ 132.274598] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.274599] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.274600] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=367 CI=366
[ 132.277588] pm80xx pm8001_mpi_msg_consume 1450:: CI=382 PI=383 msgHeader=8100200d
[ 132.277592] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.277593] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.277603] pm80xx pm8001_mpi_msg_free_set 1407: CI=383 PI=383
[ 132.923990] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.923990]
[ 132.923993] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.923994] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.923996] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=368 CI=367
[ 132.924492] pm80xx pm8001_mpi_msg_consume 1450:: CI=383 PI=384 msgHeader=8100200d
[ 132.924493] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.924494] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.924496] pm80xx pm8001_mpi_msg_free_set 1407: CI=384 PI=384
[ 132.924508] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.924508]
[ 132.924509] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.924510] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xe5 inb 0
[ 132.924511] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=369 CI=368
[ 132.924607] pm80xx pm8001_mpi_msg_consume 1450:: CI=384 PI=385 msgHeader=8100200d
[ 132.924608] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.924609] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.924610] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.924621] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.924622] pm80xx pm8001_mpi_msg_free_set 1407: CI=385 PI=385
[ 132.924640] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.924640]
[ 132.924640] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.924641] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 132.924642] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=370 CI=369
[ 132.925089] pm80xx pm8001_mpi_msg_consume 1450:: CI=385 PI=386 msgHeader=8100200d
[ 132.925090] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.925091] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.925103] pm80xx pm8001_mpi_msg_free_set 1407: CI=386 PI=386
[ 132.929540] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.929540]
[ 132.929541] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.929543] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.929544] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=371 CI=370
[ 132.932357] pm80xx pm8001_mpi_msg_consume 1450:: CI=386 PI=387 msgHeader=8100200d
[ 132.932361] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.932363] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.932372] pm80xx pm8001_mpi_msg_free_set 1407: CI=387 PI=387
[ 132.932433] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.932433]
[ 132.932435] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.932437] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.932439] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=372 CI=371
[ 132.935459] pm80xx pm8001_mpi_msg_consume 1450:: CI=387 PI=388 msgHeader=8100200d
[ 132.935463] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.935464] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.935475] pm80xx pm8001_mpi_msg_free_set 1407: CI=388 PI=388
[ 132.935534] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.935534]
[ 132.935536] pm80xx pm80xx_chip_sata_req 4105:no data
[ 132.935538] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.935540] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=373 CI=372
[ 132.973020] pm80xx pm8001_mpi_msg_consume 1450:: CI=388 PI=389 msgHeader=8100200d
[ 132.973024] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.973026] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.973027] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 132.973028] pm80xx mpi_sata_completion 2090:other len = 20
[ 132.973038] pm80xx pm8001_mpi_msg_free_set 1407: CI=389 PI=389
[ 132.973198] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.973198]
[ 132.973200] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.973202] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.973205] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=374 CI=373
[ 132.973437] pm80xx pm8001_mpi_msg_consume 1450:: CI=389 PI=390 msgHeader=8100200d
[ 132.973440] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.973441] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.973445] pm80xx pm8001_mpi_msg_free_set 1407: CI=390 PI=390
[ 132.973468] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.973468]
[ 132.973469] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.973470] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.973471] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=375 CI=374
[ 132.973777] pm80xx pm8001_mpi_msg_consume 1450:: CI=390 PI=391 msgHeader=8100200d
[ 132.973779] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.973780] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.973784] pm80xx pm8001_mpi_msg_free_set 1407: CI=391 PI=391
[ 132.973808] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.973808]
[ 132.973809] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.973810] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.973811] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=376 CI=375
[ 132.974122] pm80xx pm8001_mpi_msg_consume 1450:: CI=391 PI=392 msgHeader=8100200d
[ 132.974124] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.974125] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.974129] pm80xx pm8001_mpi_msg_free_set 1407: CI=392 PI=392
[ 132.974154] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 132.974154]
[ 132.974155] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 132.974155] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 132.974157] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=377 CI=376
[ 132.974424] pm80xx pm8001_mpi_msg_consume 1450:: CI=392 PI=393 msgHeader=8100200d
[ 132.974426] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 132.974427] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 132.974431] pm80xx pm8001_mpi_msg_free_set 1407: CI=393 PI=393
[ 160.998098] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 160.998098]
[ 160.998101] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 160.998103] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 160.998105] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=378 CI=377
[ 160.998602] pm80xx pm8001_mpi_msg_consume 1450:: CI=393 PI=394 msgHeader=8100200d
[ 160.998604] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 160.998606] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 160.998608] pm80xx pm8001_mpi_msg_free_set 1407: CI=394 PI=394
[ 160.998629] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 160.998629]
[ 160.998630] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 160.998631] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 160.998632] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=379 CI=378
[ 160.999079] pm80xx pm8001_mpi_msg_consume 1450:: CI=394 PI=395 msgHeader=8100200d
[ 160.999081] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 160.999082] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 160.999093] pm80xx pm8001_mpi_msg_free_set 1407: CI=395 PI=395
[ 161.004667] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.004667]
[ 161.004669] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.004670] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.004672] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=380 CI=379
[ 161.007874] pm80xx pm8001_mpi_msg_consume 1450:: CI=395 PI=396 msgHeader=8100200d
[ 161.007876] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.007877] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.007881] pm80xx pm8001_mpi_msg_free_set 1407: CI=396 PI=396
[ 161.007913] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.007913]
[ 161.007915] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.007917] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.007918] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=381 CI=380
[ 161.011308] pm80xx pm8001_mpi_msg_consume 1450:: CI=396 PI=397 msgHeader=8100200d
[ 161.011312] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.011314] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.011324] pm80xx pm8001_mpi_msg_free_set 1407: CI=397 PI=397
[ 161.011388] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.011388]
[ 161.011391] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.011393] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.011396] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=382 CI=381
[ 161.044962] pm80xx pm8001_mpi_msg_consume 1450:: CI=397 PI=398 msgHeader=8100200d
[ 161.044966] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.044968] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.044969] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.044969] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.044979] pm80xx pm8001_mpi_msg_free_set 1407: CI=398 PI=398
[ 161.045174] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.045174]
[ 161.045176] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.045178] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.045180] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=383 CI=382
[ 161.045407] pm80xx pm8001_mpi_msg_consume 1450:: CI=398 PI=399 msgHeader=8100200d
[ 161.045409] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.045410] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.045415] pm80xx pm8001_mpi_msg_free_set 1407: CI=399 PI=399
[ 161.045427] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.045427]
[ 161.045428] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.045429] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.045430] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=384 CI=383
[ 161.045727] pm80xx pm8001_mpi_msg_consume 1450:: CI=399 PI=400 msgHeader=8100200d
[ 161.045729] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.045730] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.045734] pm80xx pm8001_mpi_msg_free_set 1407: CI=400 PI=400
[ 161.045751] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.045751]
[ 161.045752] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.045752] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.045753] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=385 CI=384
[ 161.046057] pm80xx pm8001_mpi_msg_consume 1450:: CI=400 PI=401 msgHeader=8100200d
[ 161.046059] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.046060] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.046064] pm80xx pm8001_mpi_msg_free_set 1407: CI=401 PI=401
[ 161.046080] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.046080]
[ 161.046081] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.046082] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.046083] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=386 CI=385
[ 161.046354] pm80xx pm8001_mpi_msg_consume 1450:: CI=401 PI=402 msgHeader=8100200d
[ 161.046356] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.046357] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.046361] pm80xx pm8001_mpi_msg_free_set 1407: CI=402 PI=402
[ 161.057209] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.057209]
[ 161.057210] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.057212] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.057213] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=387 CI=386
[ 161.057689] pm80xx pm8001_mpi_msg_consume 1450:: CI=402 PI=403 msgHeader=8100200d
[ 161.057691] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.057692] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.057696] pm80xx pm8001_mpi_msg_free_set 1407: CI=403 PI=403
[ 161.057734] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.057734]
[ 161.057736] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.057737] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.057739] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=388 CI=387
[ 161.058223] pm80xx pm8001_mpi_msg_consume 1450:: CI=403 PI=404 msgHeader=8100200d
[ 161.058225] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.058226] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.058229] pm80xx pm8001_mpi_msg_free_set 1407: CI=404 PI=404
[ 161.062696] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.062696]
[ 161.062697] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.062698] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.062700] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=389 CI=388
[ 161.065954] pm80xx pm8001_mpi_msg_consume 1450:: CI=404 PI=405 msgHeader=8100200d
[ 161.065958] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.065960] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.065970] pm80xx pm8001_mpi_msg_free_set 1407: CI=405 PI=405
[ 161.066029] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.066029]
[ 161.066031] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.066033] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.066035] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=390 CI=389
[ 161.069478] pm80xx pm8001_mpi_msg_consume 1450:: CI=405 PI=406 msgHeader=8100200d
[ 161.069480] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.069481] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.069486] pm80xx pm8001_mpi_msg_free_set 1407: CI=406 PI=406
[ 161.069514] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.069514]
[ 161.069516] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.069517] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.069518] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=391 CI=390
[ 161.103042] pm80xx pm8001_mpi_msg_consume 1450:: CI=406 PI=407 msgHeader=8100200d
[ 161.103045] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.103047] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.103048] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.103049] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.103058] pm80xx pm8001_mpi_msg_free_set 1407: CI=407 PI=407
[ 161.103218] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.103218]
[ 161.103221] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.103223] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.103225] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=392 CI=391
[ 161.103484] pm80xx pm8001_mpi_msg_consume 1450:: CI=407 PI=408 msgHeader=8100200d
[ 161.103486] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.103487] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.103492] pm80xx pm8001_mpi_msg_free_set 1407: CI=408 PI=408
[ 161.103515] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.103515]
[ 161.103516] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.103517] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.103518] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=393 CI=392
[ 161.103847] pm80xx pm8001_mpi_msg_consume 1450:: CI=408 PI=409 msgHeader=8100200d
[ 161.103849] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.103850] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.103854] pm80xx pm8001_mpi_msg_free_set 1407: CI=409 PI=409
[ 161.103878] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.103878]
[ 161.103879] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.103880] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.103881] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=394 CI=393
[ 161.104220] pm80xx pm8001_mpi_msg_consume 1450:: CI=409 PI=410 msgHeader=8100200d
[ 161.104222] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.104223] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.104227] pm80xx pm8001_mpi_msg_free_set 1407: CI=410 PI=410
[ 161.104252] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.104252]
[ 161.104253] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.104254] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.104255] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=395 CI=394
[ 161.104522] pm80xx pm8001_mpi_msg_consume 1450:: CI=410 PI=411 msgHeader=8100200d
[ 161.104524] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.104525] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.104528] pm80xx pm8001_mpi_msg_free_set 1407: CI=411 PI=411
[ 161.115566] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.115566]
[ 161.115568] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.115569] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.115570] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=396 CI=395
[ 161.116052] pm80xx pm8001_mpi_msg_consume 1450:: CI=411 PI=412 msgHeader=8100200d
[ 161.116054] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.116055] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.116059] pm80xx pm8001_mpi_msg_free_set 1407: CI=412 PI=412
[ 161.116085] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.116085]
[ 161.116086] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.116087] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.116088] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=397 CI=396
[ 161.116527] pm80xx pm8001_mpi_msg_consume 1450:: CI=412 PI=413 msgHeader=8100200d
[ 161.116529] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.116530] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.116534] pm80xx pm8001_mpi_msg_free_set 1407: CI=413 PI=413
[ 161.120927] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.120927]
[ 161.120928] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.120930] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.120931] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=398 CI=397
[ 161.124188] pm80xx pm8001_mpi_msg_consume 1450:: CI=413 PI=414 msgHeader=8100200d
[ 161.124192] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.124194] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.124204] pm80xx pm8001_mpi_msg_free_set 1407: CI=414 PI=414
[ 161.124264] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.124264]
[ 161.124266] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.124268] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.124270] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=399 CI=398
[ 161.127739] pm80xx pm8001_mpi_msg_consume 1450:: CI=414 PI=415 msgHeader=8100200d
[ 161.127743] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.127745] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.127755] pm80xx pm8001_mpi_msg_free_set 1407: CI=415 PI=415
[ 161.127813] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.127813]
[ 161.127815] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.127817] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.127819] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=400 CI=399
[ 161.159683] pm80xx pm8001_mpi_msg_consume 1450:: CI=415 PI=416 msgHeader=8100200d
[ 161.159687] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.159688] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.159689] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.159690] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.159700] pm80xx pm8001_mpi_msg_free_set 1407: CI=416 PI=416
[ 161.159853] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.159853]
[ 161.159855] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.159857] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.159859] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=401 CI=400
[ 161.160110] pm80xx pm8001_mpi_msg_consume 1450:: CI=416 PI=417 msgHeader=8100200d
[ 161.160112] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.160113] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.160118] pm80xx pm8001_mpi_msg_free_set 1407: CI=417 PI=417
[ 161.160141] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.160141]
[ 161.160142] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.160143] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.160144] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=402 CI=401
[ 161.160469] pm80xx pm8001_mpi_msg_consume 1450:: CI=417 PI=418 msgHeader=8100200d
[ 161.160471] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.160472] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.160476] pm80xx pm8001_mpi_msg_free_set 1407: CI=418 PI=418
[ 161.160500] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.160500]
[ 161.160501] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.160502] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.160503] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=403 CI=402
[ 161.160826] pm80xx pm8001_mpi_msg_consume 1450:: CI=418 PI=419 msgHeader=8100200d
[ 161.160828] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.160829] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.160833] pm80xx pm8001_mpi_msg_free_set 1407: CI=419 PI=419
[ 161.160858] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.160858]
[ 161.160859] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.160859] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.160861] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=404 CI=403
[ 161.161126] pm80xx pm8001_mpi_msg_consume 1450:: CI=419 PI=420 msgHeader=8100200d
[ 161.161128] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.161129] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.161133] pm80xx pm8001_mpi_msg_free_set 1407: CI=420 PI=420
[ 161.172177] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.172177]
[ 161.172179] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.172180] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.172181] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=405 CI=404
[ 161.172669] pm80xx pm8001_mpi_msg_consume 1450:: CI=420 PI=421 msgHeader=8100200d
[ 161.172672] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.172673] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.172676] pm80xx pm8001_mpi_msg_free_set 1407: CI=421 PI=421
[ 161.172702] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.172702]
[ 161.172703] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.172704] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.172705] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=406 CI=405
[ 161.173195] pm80xx pm8001_mpi_msg_consume 1450:: CI=421 PI=422 msgHeader=8100200d
[ 161.173197] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.173198] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.173202] pm80xx pm8001_mpi_msg_free_set 1407: CI=422 PI=422
[ 161.177673] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.177673]
[ 161.177675] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.177676] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.177677] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=407 CI=406
[ 161.180516] pm80xx pm8001_mpi_msg_consume 1450:: CI=422 PI=423 msgHeader=8100200d
[ 161.180518] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.180519] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.180523] pm80xx pm8001_mpi_msg_free_set 1407: CI=423 PI=423
[ 161.180547] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.180547]
[ 161.180548] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.180548] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.180550] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=408 CI=407
[ 161.183595] pm80xx pm8001_mpi_msg_consume 1450:: CI=423 PI=424 msgHeader=8100200d
[ 161.183599] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.183601] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.183610] pm80xx pm8001_mpi_msg_free_set 1407: CI=424 PI=424
[ 161.183668] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.183668]
[ 161.183670] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.183672] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.183674] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=409 CI=408
[ 161.216565] pm80xx pm8001_mpi_msg_consume 1450:: CI=424 PI=425 msgHeader=8100200d
[ 161.216569] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.216570] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.216571] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.216572] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.216581] pm80xx pm8001_mpi_msg_free_set 1407: CI=425 PI=425
[ 161.216740] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.216740]
[ 161.216742] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.216744] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.216746] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=410 CI=409
[ 161.216979] pm80xx pm8001_mpi_msg_consume 1450:: CI=425 PI=426 msgHeader=8100200d
[ 161.216981] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.216981] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.216984] pm80xx pm8001_mpi_msg_free_set 1407: CI=426 PI=426
[ 161.216998] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.216998]
[ 161.216999] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.217000] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.217002] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=411 CI=410
[ 161.217298] pm80xx pm8001_mpi_msg_consume 1450:: CI=426 PI=427 msgHeader=8100200d
[ 161.217299] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.217300] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.217303] pm80xx pm8001_mpi_msg_free_set 1407: CI=427 PI=427
[ 161.217323] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.217323]
[ 161.217324] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.217327] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.217329] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=412 CI=411
[ 161.217627] pm80xx pm8001_mpi_msg_consume 1450:: CI=427 PI=428 msgHeader=8100200d
[ 161.217628] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.217629] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.217632] pm80xx pm8001_mpi_msg_free_set 1407: CI=428 PI=428
[ 161.217656] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.217656]
[ 161.217657] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.217659] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.217660] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=413 CI=412
[ 161.217925] pm80xx pm8001_mpi_msg_consume 1450:: CI=428 PI=429 msgHeader=8100200d
[ 161.217927] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.217928] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.217932] pm80xx pm8001_mpi_msg_free_set 1407: CI=429 PI=429
[ 161.239414] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.239414]
[ 161.239416] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.239418] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.239420] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=414 CI=413
[ 161.239912] pm80xx pm8001_mpi_msg_consume 1450:: CI=429 PI=430 msgHeader=8100200d
[ 161.239914] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.239915] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.239920] pm80xx pm8001_mpi_msg_free_set 1407: CI=430 PI=430
[ 161.239949] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.239949]
[ 161.239950] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.239951] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.239952] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=415 CI=414
[ 161.240408] pm80xx pm8001_mpi_msg_consume 1450:: CI=430 PI=431 msgHeader=8100200d
[ 161.240410] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.240411] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.240416] pm80xx pm8001_mpi_msg_free_set 1407: CI=431 PI=431
[ 161.245903] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.245903]
[ 161.245904] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.245906] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.245907] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=416 CI=415
[ 161.249113] pm80xx pm8001_mpi_msg_consume 1450:: CI=431 PI=432 msgHeader=8100200d
[ 161.249115] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.249116] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.249119] pm80xx pm8001_mpi_msg_free_set 1407: CI=432 PI=432
[ 161.249150] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.249150]
[ 161.249152] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.249153] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.249155] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=417 CI=416
[ 161.252549] pm80xx pm8001_mpi_msg_consume 1450:: CI=432 PI=433 msgHeader=8100200d
[ 161.252553] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.252555] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.252565] pm80xx pm8001_mpi_msg_free_set 1407: CI=433 PI=433
[ 161.252623] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.252623]
[ 161.252625] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.252627] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.252629] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=418 CI=417
[ 161.298074] pm80xx pm8001_mpi_msg_consume 1450:: CI=433 PI=434 msgHeader=8100200d
[ 161.298078] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.298080] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.298081] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.298082] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.298092] pm80xx pm8001_mpi_msg_free_set 1407: CI=434 PI=434
[ 161.298241] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.298241]
[ 161.298243] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.298245] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.298247] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=419 CI=418
[ 161.298472] pm80xx pm8001_mpi_msg_consume 1450:: CI=434 PI=435 msgHeader=8100200d
[ 161.298474] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.298476] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.298481] pm80xx pm8001_mpi_msg_free_set 1407: CI=435 PI=435
[ 161.298511] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.298511]
[ 161.298513] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.298514] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.298515] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=420 CI=419
[ 161.298812] pm80xx pm8001_mpi_msg_consume 1450:: CI=435 PI=436 msgHeader=8100200d
[ 161.298814] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.298815] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.298819] pm80xx pm8001_mpi_msg_free_set 1407: CI=436 PI=436
[ 161.298852] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.298852]
[ 161.298854] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.298855] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.298856] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=421 CI=420
[ 161.299161] pm80xx pm8001_mpi_msg_consume 1450:: CI=436 PI=437 msgHeader=8100200d
[ 161.299163] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.299164] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.299167] pm80xx pm8001_mpi_msg_free_set 1407: CI=437 PI=437
[ 161.299193] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.299193]
[ 161.299194] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.299195] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.299196] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=422 CI=421
[ 161.299468] pm80xx pm8001_mpi_msg_consume 1450:: CI=437 PI=438 msgHeader=8100200d
[ 161.299470] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.299471] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.299475] pm80xx pm8001_mpi_msg_free_set 1407: CI=438 PI=438
[ 161.317775] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.317775]
[ 161.317777] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.317779] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.317780] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=423 CI=422
[ 161.318274] pm80xx pm8001_mpi_msg_consume 1450:: CI=438 PI=439 msgHeader=8100200d
[ 161.318276] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.318277] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.318281] pm80xx pm8001_mpi_msg_free_set 1407: CI=439 PI=439
[ 161.318306] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.318306]
[ 161.318307] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.318308] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.318309] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=424 CI=423
[ 161.318768] pm80xx pm8001_mpi_msg_consume 1450:: CI=439 PI=440 msgHeader=8100200d
[ 161.318770] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.318771] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.318775] pm80xx pm8001_mpi_msg_free_set 1407: CI=440 PI=440
[ 161.323143] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.323143]
[ 161.323144] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.323146] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.323147] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=425 CI=424
[ 161.326343] pm80xx pm8001_mpi_msg_consume 1450:: CI=440 PI=441 msgHeader=8100200d
[ 161.326345] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.326346] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.326350] pm80xx pm8001_mpi_msg_free_set 1407: CI=441 PI=441
[ 161.326380] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.326380]
[ 161.326382] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.326383] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.326384] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=426 CI=425
[ 161.329752] pm80xx pm8001_mpi_msg_consume 1450:: CI=441 PI=442 msgHeader=8100200d
[ 161.329755] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.329757] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.329768] pm80xx pm8001_mpi_msg_free_set 1407: CI=442 PI=442
[ 161.329825] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.329825]
[ 161.329828] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.329830] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.329831] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=427 CI=426
[ 161.369174] pm80xx pm8001_mpi_msg_consume 1450:: CI=442 PI=443 msgHeader=8100200d
[ 161.369177] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.369179] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.369180] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.369181] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.369191] pm80xx pm8001_mpi_msg_free_set 1407: CI=443 PI=443
[ 161.369345] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.369345]
[ 161.369347] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.369349] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.369351] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=428 CI=427
[ 161.369576] pm80xx pm8001_mpi_msg_consume 1450:: CI=443 PI=444 msgHeader=8100200d
[ 161.369578] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.369579] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.369584] pm80xx pm8001_mpi_msg_free_set 1407: CI=444 PI=444
[ 161.369614] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.369614]
[ 161.369616] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.369617] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.369618] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=429 CI=428
[ 161.369916] pm80xx pm8001_mpi_msg_consume 1450:: CI=444 PI=445 msgHeader=8100200d
[ 161.369918] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.369919] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.369922] pm80xx pm8001_mpi_msg_free_set 1407: CI=445 PI=445
[ 161.369955] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.369955]
[ 161.369957] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.369958] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.369959] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=430 CI=429
[ 161.370262] pm80xx pm8001_mpi_msg_consume 1450:: CI=445 PI=446 msgHeader=8100200d
[ 161.370264] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.370265] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.370268] pm80xx pm8001_mpi_msg_free_set 1407: CI=446 PI=446
[ 161.370295] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.370295]
[ 161.370296] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.370297] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.370298] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=431 CI=430
[ 161.370567] pm80xx pm8001_mpi_msg_consume 1450:: CI=446 PI=447 msgHeader=8100200d
[ 161.370569] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.370570] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.370574] pm80xx pm8001_mpi_msg_free_set 1407: CI=447 PI=447
[ 161.384493] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.384493]
[ 161.384495] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.384497] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.384500] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=432 CI=431
[ 161.400157] pm80xx pm8001_mpi_msg_consume 1450:: CI=447 PI=448 msgHeader=8100200d
[ 161.400160] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.400162] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.400172] pm80xx pm8001_mpi_msg_free_set 1407: CI=448 PI=448
[ 161.400236] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.400236]
[ 161.400239] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.400241] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.400243] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=433 CI=432
[ 161.400704] pm80xx pm8001_mpi_msg_consume 1450:: CI=448 PI=449 msgHeader=8100200d
[ 161.400706] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.400707] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.400712] pm80xx pm8001_mpi_msg_free_set 1407: CI=449 PI=449
[ 161.405212] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.405212]
[ 161.405213] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.405214] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.405225] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=434 CI=433
[ 161.408458] pm80xx pm8001_mpi_msg_consume 1450:: CI=449 PI=450 msgHeader=8100200d
[ 161.408462] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.408464] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.408473] pm80xx pm8001_mpi_msg_free_set 1407: CI=450 PI=450
[ 161.408532] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.408532]
[ 161.408535] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.408537] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.408539] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=435 CI=434
[ 161.411968] pm80xx pm8001_mpi_msg_consume 1450:: CI=450 PI=451 msgHeader=8100200d
[ 161.411972] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.411974] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.411984] pm80xx pm8001_mpi_msg_free_set 1407: CI=451 PI=451
[ 161.412041] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.412041]
[ 161.412044] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.412045] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.412047] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=436 CI=435
[ 161.438088] pm80xx pm8001_mpi_msg_consume 1450:: CI=451 PI=452 msgHeader=8100200d
[ 161.438091] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.438093] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.438094] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.438095] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.438104] pm80xx pm8001_mpi_msg_free_set 1407: CI=452 PI=452
[ 161.438257] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.438257]
[ 161.438259] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.438261] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.438263] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=437 CI=436
[ 161.438479] pm80xx pm8001_mpi_msg_consume 1450:: CI=452 PI=453 msgHeader=8100200d
[ 161.438481] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.438482] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.438487] pm80xx pm8001_mpi_msg_free_set 1407: CI=453 PI=453
[ 161.438517] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.438517]
[ 161.438519] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.438520] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.438521] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=438 CI=437
[ 161.438811] pm80xx pm8001_mpi_msg_consume 1450:: CI=453 PI=454 msgHeader=8100200d
[ 161.438813] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.438814] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.438817] pm80xx pm8001_mpi_msg_free_set 1407: CI=454 PI=454
[ 161.438844] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.438844]
[ 161.438845] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.438845] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.438847] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=439 CI=438
[ 161.439146] pm80xx pm8001_mpi_msg_consume 1450:: CI=454 PI=455 msgHeader=8100200d
[ 161.439148] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.439149] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.439153] pm80xx pm8001_mpi_msg_free_set 1407: CI=455 PI=455
[ 161.439178] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.439178]
[ 161.439179] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.439180] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.439181] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=440 CI=439
[ 161.439446] pm80xx pm8001_mpi_msg_consume 1450:: CI=455 PI=456 msgHeader=8100200d
[ 161.439448] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.439449] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.439453] pm80xx pm8001_mpi_msg_free_set 1407: CI=456 PI=456
[ 161.451185] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.451185]
[ 161.451187] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.451189] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.451191] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=441 CI=440
[ 161.451678] pm80xx pm8001_mpi_msg_consume 1450:: CI=456 PI=457 msgHeader=8100200d
[ 161.451681] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.451682] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.451687] pm80xx pm8001_mpi_msg_free_set 1407: CI=457 PI=457
[ 161.451719] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.451719]
[ 161.451721] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.451722] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.451724] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=442 CI=441
[ 161.452171] pm80xx pm8001_mpi_msg_consume 1450:: CI=457 PI=458 msgHeader=8100200d
[ 161.452174] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.452175] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.452180] pm80xx pm8001_mpi_msg_free_set 1407: CI=458 PI=458
[ 161.458700] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.458700]
[ 161.458702] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.458704] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.458706] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=443 CI=442
[ 161.461943] pm80xx pm8001_mpi_msg_consume 1450:: CI=458 PI=459 msgHeader=8100200d
[ 161.461947] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.461949] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.461959] pm80xx pm8001_mpi_msg_free_set 1407: CI=459 PI=459
[ 161.462018] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.462018]
[ 161.462020] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.462022] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.462025] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=444 CI=443
[ 161.465452] pm80xx pm8001_mpi_msg_consume 1450:: CI=459 PI=460 msgHeader=8100200d
[ 161.465455] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.465457] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.465467] pm80xx pm8001_mpi_msg_free_set 1407: CI=460 PI=460
[ 161.465525] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.465525]
[ 161.465528] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.465530] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.465532] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=445 CI=444
[ 161.492697] pm80xx pm8001_mpi_msg_consume 1450:: CI=460 PI=461 msgHeader=8100200d
[ 161.492700] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.492702] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.492703] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.492704] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.492713] pm80xx pm8001_mpi_msg_free_set 1407: CI=461 PI=461
[ 161.492877] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.492877]
[ 161.492879] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.492881] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.492883] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=446 CI=445
[ 161.493105] pm80xx pm8001_mpi_msg_consume 1450:: CI=461 PI=462 msgHeader=8100200d
[ 161.493107] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.493108] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.493113] pm80xx pm8001_mpi_msg_free_set 1407: CI=462 PI=462
[ 161.493143] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.493143]
[ 161.493145] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.493147] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.493148] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=447 CI=446
[ 161.493442] pm80xx pm8001_mpi_msg_consume 1450:: CI=462 PI=463 msgHeader=8100200d
[ 161.493444] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.493445] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.493449] pm80xx pm8001_mpi_msg_free_set 1407: CI=463 PI=463
[ 161.493482] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.493482]
[ 161.493483] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.493485] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.493486] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=448 CI=447
[ 161.493786] pm80xx pm8001_mpi_msg_consume 1450:: CI=463 PI=464 msgHeader=8100200d
[ 161.493788] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.493789] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.493793] pm80xx pm8001_mpi_msg_free_set 1407: CI=464 PI=464
[ 161.493828] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.493828]
[ 161.493829] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.493831] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.493832] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=449 CI=448
[ 161.494095] pm80xx pm8001_mpi_msg_consume 1450:: CI=464 PI=465 msgHeader=8100200d
[ 161.494097] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.494098] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.494102] pm80xx pm8001_mpi_msg_free_set 1407: CI=465 PI=465
[ 161.512006] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.512006]
[ 161.512008] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.512010] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.512012] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=450 CI=449
[ 161.512498] pm80xx pm8001_mpi_msg_consume 1450:: CI=465 PI=466 msgHeader=8100200d
[ 161.512501] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.512502] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.512507] pm80xx pm8001_mpi_msg_free_set 1407: CI=466 PI=466
[ 161.512536] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.512536]
[ 161.512537] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.512538] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.512539] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=451 CI=450
[ 161.512985] pm80xx pm8001_mpi_msg_consume 1450:: CI=466 PI=467 msgHeader=8100200d
[ 161.512988] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.512989] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.512993] pm80xx pm8001_mpi_msg_free_set 1407: CI=467 PI=467
[ 161.518572] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.518572]
[ 161.518574] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.518576] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.518577] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=452 CI=451
[ 161.521838] pm80xx pm8001_mpi_msg_consume 1450:: CI=467 PI=468 msgHeader=8100200d
[ 161.521839] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.521840] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.521844] pm80xx pm8001_mpi_msg_free_set 1407: CI=468 PI=468
[ 161.521875] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.521875]
[ 161.521876] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.521878] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.521879] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=453 CI=452
[ 161.525293] pm80xx pm8001_mpi_msg_consume 1450:: CI=468 PI=469 msgHeader=8100200d
[ 161.525295] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.525296] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.525300] pm80xx pm8001_mpi_msg_free_set 1407: CI=469 PI=469
[ 161.525330] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.525330]
[ 161.525332] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.525333] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.525334] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=454 CI=453
[ 161.558095] pm80xx pm8001_mpi_msg_consume 1450:: CI=469 PI=470 msgHeader=8100200d
[ 161.558099] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.558101] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.558101] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.558102] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.558112] pm80xx pm8001_mpi_msg_free_set 1407: CI=470 PI=470
[ 161.558265] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.558265]
[ 161.558268] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.558270] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.558272] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=455 CI=454
[ 161.558493] pm80xx pm8001_mpi_msg_consume 1450:: CI=470 PI=471 msgHeader=8100200d
[ 161.558495] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.558496] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.558501] pm80xx pm8001_mpi_msg_free_set 1407: CI=471 PI=471
[ 161.558524] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.558524]
[ 161.558525] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.558526] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.558527] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=456 CI=455
[ 161.558824] pm80xx pm8001_mpi_msg_consume 1450:: CI=471 PI=472 msgHeader=8100200d
[ 161.558826] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.558827] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.558831] pm80xx pm8001_mpi_msg_free_set 1407: CI=472 PI=472
[ 161.558855] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.558855]
[ 161.558856] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.558857] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.558858] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=457 CI=456
[ 161.559158] pm80xx pm8001_mpi_msg_consume 1450:: CI=472 PI=473 msgHeader=8100200d
[ 161.559160] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.559161] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.559165] pm80xx pm8001_mpi_msg_free_set 1407: CI=473 PI=473
[ 161.559190] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.559190]
[ 161.559191] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.559192] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.559193] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=458 CI=457
[ 161.559455] pm80xx pm8001_mpi_msg_consume 1450:: CI=473 PI=474 msgHeader=8100200d
[ 161.559457] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.559458] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.559462] pm80xx pm8001_mpi_msg_free_set 1407: CI=474 PI=474
[ 161.571447] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.571447]
[ 161.571450] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.571452] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.571454] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=459 CI=458
[ 161.571928] pm80xx pm8001_mpi_msg_consume 1450:: CI=474 PI=475 msgHeader=8100200d
[ 161.571931] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.571933] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.571938] pm80xx pm8001_mpi_msg_free_set 1407: CI=475 PI=475
[ 161.571968] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.571968]
[ 161.571970] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.571971] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.571972] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=460 CI=459
[ 161.572426] pm80xx pm8001_mpi_msg_consume 1450:: CI=475 PI=476 msgHeader=8100200d
[ 161.572428] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.572430] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.572435] pm80xx pm8001_mpi_msg_free_set 1407: CI=476 PI=476
[ 161.578928] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.578928]
[ 161.578930] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.578932] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.578934] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=461 CI=460
[ 161.582154] pm80xx pm8001_mpi_msg_consume 1450:: CI=476 PI=477 msgHeader=8100200d
[ 161.582156] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.582157] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.582161] pm80xx pm8001_mpi_msg_free_set 1407: CI=477 PI=477
[ 161.582192] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.582192]
[ 161.582193] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.582195] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.582196] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=462 CI=461
[ 161.585553] pm80xx pm8001_mpi_msg_consume 1450:: CI=477 PI=478 msgHeader=8100200d
[ 161.585557] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.585559] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.585569] pm80xx pm8001_mpi_msg_free_set 1407: CI=478 PI=478
[ 161.585627] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.585627]
[ 161.585630] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.585632] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.585634] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=463 CI=462
[ 161.614523] pm80xx pm8001_mpi_msg_consume 1450:: CI=478 PI=479 msgHeader=8100200d
[ 161.614526] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.614528] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.614529] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.614530] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.614539] pm80xx pm8001_mpi_msg_free_set 1407: CI=479 PI=479
[ 161.614688] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.614688]
[ 161.614690] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.614692] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.614694] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=464 CI=463
[ 161.614910] pm80xx pm8001_mpi_msg_consume 1450:: CI=479 PI=480 msgHeader=8100200d
[ 161.614913] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.614914] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.614919] pm80xx pm8001_mpi_msg_free_set 1407: CI=480 PI=480
[ 161.614942] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.614942]
[ 161.614943] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.614943] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.614945] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=465 CI=464
[ 161.615234] pm80xx pm8001_mpi_msg_consume 1450:: CI=480 PI=481 msgHeader=8100200d
[ 161.615236] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.615237] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.615241] pm80xx pm8001_mpi_msg_free_set 1407: CI=481 PI=481
[ 161.615265] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.615265]
[ 161.615265] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.615266] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.615267] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=466 CI=465
[ 161.615565] pm80xx pm8001_mpi_msg_consume 1450:: CI=481 PI=482 msgHeader=8100200d
[ 161.615567] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.615568] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.615572] pm80xx pm8001_mpi_msg_free_set 1407: CI=482 PI=482
[ 161.615597] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.615597]
[ 161.615598] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.615599] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.615600] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=467 CI=466
[ 161.615862] pm80xx pm8001_mpi_msg_consume 1450:: CI=482 PI=483 msgHeader=8100200d
[ 161.615864] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.615865] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.615869] pm80xx pm8001_mpi_msg_free_set 1407: CI=483 PI=483
[ 161.626929] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.626929]
[ 161.626930] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.626932] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.626933] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=468 CI=467
[ 161.627419] pm80xx pm8001_mpi_msg_consume 1450:: CI=483 PI=484 msgHeader=8100200d
[ 161.627420] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.627421] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.627425] pm80xx pm8001_mpi_msg_free_set 1407: CI=484 PI=484
[ 161.627459] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.627459]
[ 161.627460] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.627460] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xec inb 0
[ 161.627462] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=469 CI=468
[ 161.627902] pm80xx pm8001_mpi_msg_consume 1450:: CI=484 PI=485 msgHeader=8100200d
[ 161.627904] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.627905] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.627908] pm80xx pm8001_mpi_msg_free_set 1407: CI=485 PI=485
[ 161.633926] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.633926]
[ 161.633928] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.633930] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.633932] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=470 CI=469
[ 161.637110] pm80xx pm8001_mpi_msg_consume 1450:: CI=485 PI=486 msgHeader=8100200d
[ 161.637113] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.637114] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.637119] pm80xx pm8001_mpi_msg_free_set 1407: CI=486 PI=486
[ 161.637155] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.637155]
[ 161.637157] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.637159] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.637161] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=471 CI=470
[ 161.640511] pm80xx pm8001_mpi_msg_consume 1450:: CI=486 PI=487 msgHeader=8100200d
[ 161.640514] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.640515] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.640520] pm80xx pm8001_mpi_msg_free_set 1407: CI=487 PI=487
[ 161.640548] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.640548]
[ 161.640550] pm80xx pm80xx_chip_sata_req 4105:no data
[ 161.640551] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.640552] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=472 CI=471
[ 161.687008] pm80xx pm8001_mpi_msg_consume 1450:: CI=487 PI=488 msgHeader=8100200d
[ 161.687011] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.687013] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.687014] pm80xx mpi_sata_completion 2075:SAS_PROTO_RESPONSE len = 20
[ 161.687015] pm80xx mpi_sata_completion 2090:other len = 20
[ 161.687024] pm80xx pm8001_mpi_msg_free_set 1407: CI=488 PI=488
[ 161.687179] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.687179]
[ 161.687182] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.687184] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.687186] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=473 CI=472
[ 161.687408] pm80xx pm8001_mpi_msg_consume 1450:: CI=488 PI=489 msgHeader=8100200d
[ 161.687411] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.687412] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.687416] pm80xx pm8001_mpi_msg_free_set 1407: CI=489 PI=489
[ 161.687440] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.687440]
[ 161.687441] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.687442] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.687445] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=474 CI=473
[ 161.687741] pm80xx pm8001_mpi_msg_consume 1450:: CI=489 PI=490 msgHeader=8100200d
[ 161.687743] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.687744] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.687748] pm80xx pm8001_mpi_msg_free_set 1407: CI=490 PI=490
[ 161.687772] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.687772]
[ 161.687773] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.687774] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.687775] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=475 CI=474
[ 161.688078] pm80xx pm8001_mpi_msg_consume 1450:: CI=490 PI=491 msgHeader=8100200d
[ 161.688080] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.688081] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.688085] pm80xx pm8001_mpi_msg_free_set 1407: CI=491 PI=491
[ 161.688110] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 161.688110]
[ 161.688111] pm80xx pm80xx_chip_sata_req 4112:PIO
[ 161.688112] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xb0 inb 0
[ 161.688113] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=476 CI=475
[ 161.688378] pm80xx pm8001_mpi_msg_consume 1450:: CI=491 PI=492 msgHeader=8100200d
[ 161.688380] pm80xx process_one_iomb 3541:OPC_OUB_SATA_COMP
[ 161.688380] pm80xx mpi_sata_completion 2051:IO_SUCCESS
[ 161.688384] pm80xx pm8001_mpi_msg_free_set 1407: CI=492 PI=492
[ 190.814105] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814105]
[ 190.814113] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814119] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814125] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=477 CI=476
[ 190.814137] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814137]
[ 190.814140] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814143] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814147] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=478 CI=476
[ 190.814158] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814158]
[ 190.814160] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814164] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814167] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=479 CI=476
[ 190.814177] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814177]
[ 190.814180] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814183] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814186] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=480 CI=476
[ 190.814196] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814196]
[ 190.814198] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814201] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814205] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=481 CI=476
[ 190.814214] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814214]
[ 190.814216] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814219] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814223] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=482 CI=476
[ 190.814232] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814232]
[ 190.814235] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814238] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814241] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=483 CI=476
[ 190.814251] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814251]
[ 190.814253] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814256] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814260] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=484 CI=476
[ 190.814270] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814270]
[ 190.814273] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814276] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814279] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=485 CI=476
[ 190.814289] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 190.814289]
[ 190.814292] pm80xx pm80xx_chip_sata_req 4105:no data
[ 190.814295] pm80xx pm80xx_chip_sata_req 4207:Sending Normal SATA command 0xea inb 0
[ 190.814298] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:17 , UPDATED PI=486 CI=476
[ 220.969757] sd 0:0:9:0: [sdj] command ffff880407bf5c00 timed out
[ 220.969777] sd 0:0:10:0: [sdk] command ffff880407bf4d00 timed out
[ 220.969784] sd 0:0:0:0: [sdb] command ffff880407bf5d00 timed out
[ 220.969788] sd 0:0:4:0: [sdf] command ffff880407bf4100 timed out
[ 220.969793] sd 0:0:3:0: [sde] command ffff880407bf4400 timed out
[ 220.969798] sd 0:0:1:0: [sdc] command ffff880407bf5700 timed out
[ 220.969803] sd 0:0:7:0: [sdh] command ffff880407bf5200 timed out
[ 220.969808] sd 0:0:8:0: [sdi] command ffff880407bf5e00 timed out
[ 220.969812] sd 0:0:2:0: [sdd] command ffff880407bf4f00 timed out
[ 220.969829] sd 0:0:5:0: [sdg] command ffff880407bf4c00 timed out
[ 220.969867] sas: Enter sas_scsi_recover_host busy: 10 failed: 10
[ 220.969882] sas: trying to find task 0xffff880035cdd680
[ 220.969888] sas: sas_scsi_find_task: aborting task 0xffff880035cdd680
[ 220.969900] pm80xx pm8001_chip_abort_task 4718:cmd_tag = e, abort task tag = 0x3
[ 220.969913] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:18 , UPDATED PI=487 CI=476
[ 240.972521] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 240.972532] pm80xx pm8001_abort_task 1245:rc= 5
[ 240.972538] sas: sas_scsi_find_task: querying task 0xffff880035cdd680
[ 240.972541] pm80xx pm8001_query_task 1168::rc= 5
[ 240.972544] sas: sas_scsi_find_task: task 0xffff880035cdd680 failed to abort
[ 240.972547] sas: task 0xffff880035cdd680 is not at LU: I_T recover
[ 240.972551] sas: I_T nexus reset for dev 50030480010f712e
[ 240.972566] pm80xx pm8001_task_exec 383:pm8001_task_exec device
[ 240.972566]
[ 240.972573] pm80xx pm80xx_chip_smp_req 3806:SMP Frame Length 44
[ 240.972576] pm80xx pm80xx_chip_smp_req 3819:SMP REQUEST INDIRECT MODE
[ 240.972581] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:12 , UPDATED PI=488 CI=476
[ 250.977650] sas: smp task timed out or aborted
[ 250.977669] pm80xx pm8001_chip_abort_task 4718:cmd_tag = 10, abort task tag = 0xf
[ 250.977676] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:14 , UPDATED PI=489 CI=476
[ 271.022264] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 271.022270] pm80xx pm8001_abort_task 1245:rc= 5
[ 271.022272] sas: SMP task aborted and not done
[ 273.024354] pm80xx pm8001_chip_abort_task 4718:cmd_tag = 11, abort task tag = 0x0
[ 273.024363] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:18 , UPDATED PI=490 CI=476
[ 293.080977] pm80xx pm8001_exec_internal_task_abort 834:TMF task timeout.
[ 293.080992] pm80xx pm8001_mpi_build_cmd 1368:INB Q 0 OPCODE:2a , UPDATED PI=491 CI=476
[ 361.606803] INFO: task sync:2812 blocked for more than 120 seconds.
[ 361.613171] Not tainted 3.13.0-35-generic #62-Ubuntu
[ 361.618727] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 361.626628] sync D ffff88041fcd4440 0 2812 2328 0x00000000
[ 361.626637] ffff880403fd7d50 0000000000000086 ffff880408601800 ffff880403fd7fd8
[ 361.626645] 0000000000014440 0000000000014440 ffff880408601800 ffff880403fd7e78
[ 361.626651] ffff880403fd7e80 7fffffffffffffff ffff880408601800 ffffffff811ecf30
[ 361.626658] Call Trace:
[ 361.626688] [<ffffffff811ecf30>] ? do_fsync+0x80/0x80
[ 361.626702] [<ffffffff81722749>] schedule+0x29/0x70
[ 361.626709] [<ffffffff81721999>] schedule_timeout+0x239/0x2d0
[ 361.626715] [<ffffffff811ecf30>] ? do_fsync+0x80/0x80
[ 361.626725] [<ffffffff815a4bc5>] ? md_make_request+0xd5/0x220
[ 361.626739] [<ffffffff811ecf30>] ? do_fsync+0x80/0x80
[ 361.626748] [<ffffffff815b9837>] ? dm_request+0x107/0x1a0
[ 361.626759] [<ffffffff811ecf30>] ? do_fsync+0x80/0x80
[ 361.626766] [<ffffffff81723266>] wait_for_completion+0xa6/0x160
[ 361.626777] [<ffffffff8109a8d0>] ? wake_up_state+0x20/0x20
[ 361.626783] [<ffffffff811f356e>] submit_bio_wait+0x5e/0x70
[ 361.626791] [<ffffffff8133bb7a>] blkdev_issue_flush+0x5a/0x90
[ 361.626812] [<ffffffff81255da9>] ext4_sync_fs+0xd9/0x130
[ 361.626821] [<ffffffff811ecf50>] sync_fs_one_sb+0x20/0x30
[ 361.626831] [<ffffffff811c0a62>] iterate_supers+0xb2/0x110
[ 361.626842] [<ffffffff811ed055>] sys_sync+0x55/0x90
[ 361.626849] [<ffffffff8172ed6d>] system_call_fastpath+0x1a/0x1f
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Adaptec 71605H HBA randomly failing to detect any drives at init
2014-09-05 22:13 ` Andrew Robertson
2014-09-06 5:32 ` Fwd: " Andrew Robertson
@ 2015-05-18 19:19 ` Andrew Robertson
1 sibling, 0 replies; 6+ messages in thread
From: Andrew Robertson @ 2015-05-18 19:19 UTC (permalink / raw)
To: linux-scsi
Update for anyone who saw this and wonders what happened:
As more drives were added in, the systems got more and more unstable
at boot. With <8 drives, it booted pretty every time. With 11 drives
(described in my original post), it failed at init ~3 out of 4 times.
Once I added the 12th drive I couldn't get it to come up any longer
even after a dozen or so reboots; there would be timeouts in the
pm80xx module, and no drives attached to that would show up.
One suggestion was to use shorter cables -- but I couldn't use any
cables shorter than 0.8m as that didn't fit in the chassis (supermicro
36-slot chassis).
I also tried the latest kernels to no avail, and also tried adjusting
the module init timeouts in the code to see if that made a difference
(no difference). The adaptec card was at the latest firmware (and
still is, there haven't been any updates), with the stock linux
drivers for the pm80xx card.
There was a comment that it's best to match the expander chip vendor
(LSI SAS2X28 & SAS2X36) with the hba vendor - so I ended up replacing
the adaptec 71605H with an LSI 9207-8i HBA (using a 1m cable to each
expander). After the HBA swap, both (all) systems are working
perfectly.
On Fri, Sep 5, 2014 at 3:13 PM, Andrew Robertson
<andyrobertson101@gmail.com> wrote:
> More info, as requested:
>
> There are 2 sas expander chips in the system (LSI SAS2X28 & SAS2X36),
> and there's a connection to each of them from the 71605H via a
> separate 0.8m Adaptec cable. (Adaptec 2280200-R). This is a
> Supermicro chassis.
>
> Firmware version:
> # cat /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/host0/scsi_host/host0/fw_version
> 02.08.60.01
>
> I don't have immediate physical access to the box, so I'm not able to
> do the hotplug logging test. However, I did "reset" the PCI device
> via /sys, as shown below, and captured the logs from that (attached,
> "dmesg.out.txt").
>
> With the latest kernel, v3.17-rc3, I got a kernel "null pointer
> dereference" in the pm80xx module (dmesg output pasted in below).
>
> I will also try replacing the cables with 0.5m adaptec cables as
> suggested to see if that helps.
>
> ---
>
> Reset test:
>
> # find /sys -iname logging_level
> /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/host0/scsi_host/host0/logging_level
> # echo 0xfff > /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/host0/scsi_host/host0/logging_level
> # echo 1 > /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/rescan
> # echo 1 > /sys/devices/pci0000:00/0000:00:01.1/0000:02:00.0/reset
> # sync
> (at which point the process hung; in the dmesg you can see a "sync
> blocked for more than 120 seconds")
>
>
> The disk/expander layout looks like:
> [0:0:0:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdb /dev/sg1
> [0:0:1:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdc /dev/sg2
> [0:0:2:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdd /dev/sg3
> [0:0:3:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sde /dev/sg4
> [0:0:4:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdf /dev/sg5
> [0:0:5:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdg /dev/sg6
> [0:0:6:0] enclosu LSI SAS2X36 0e12 - /dev/sg7
> [0:0:7:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdh /dev/sg8
> [0:0:8:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdi /dev/sg9
> [0:0:9:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdj /dev/sg10
> [0:0:10:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdk /dev/sg11
> [0:0:11:0] disk ATA WDC WD60EFRX-68M 82.0 /dev/sdl /dev/sg12
> [0:0:12:0] enclosu LSI SAS2X28 0e12 - /dev/sg13
>
>
> dmesg from latest kernel v3.17-rc3 showing (what appears to possibly
> be) a kernel bug:
>
> This happened right after I ran "lsscsi" (though can't say if it was
> actually caused by that).
>
> [ 309.327805] BUG: unable to handle kernel NULL pointer dereference
> at 0000000000000290
> [ 309.335829] IP: [<ffffffffc0080d4f>]
> pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
> [ 309.343258] PGD 0
> [ 309.345381] Oops: 0000 [#1] SMP
> [ 309.348797] Modules linked in: ipmi_devintf autofs4 arc4 nfsd
> auth_rpcgss intel_rapl nfs_acl x86_pkg_temp_thermal nfs
> intel_powerclamp coretemp lockd kvm_intel sunrpc kvm fscache
> crct10dif_pclmul ttm crc32_pclmul drm_kms_helper rt2800usb
> ghash_clmulni_intel rt2x00usb rt2800lib rt2x00lib mac80211 aesni_intel
> drm aes_x86_64 lrw gf128mul glue_helper ablk_helper cfg80211 cryptd
> crc_ccitt syscopyarea joydev sysfillrect sysimgblt shpchp lpc_ich
> ipmi_si ipmi_msghandler mac_hid video ie31200_edac edac_core lp
> parport ses enclosure hid_generic usbhid hid raid10 raid456
> async_raid6_recov async_memcpy async_pq async_xor async_tx xor igb
> raid6_pq i2c_algo_bit raid1 e1000e pm80xx dca raid0 libsas ahci ptp
> multipath scsi_transport_sas libahci pps_core linear
> [ 309.420132] CPU: 5 PID: 1998 Comm: kworker/5:2 Not tainted
> 3.17.0-031700rc3-generic #201409031132
> [ 309.429051] Hardware name: Supermicro X10SLL-F/X10SLL-F, BIOS 2.0 04/24/2014
> [ 309.436148] Workqueue: pm80xx pm8001_work_fn [pm80xx]
> [ 309.441317] task: ffff880403690000 ti: ffff880404fa4000 task.ti:
> ffff880404fa4000
> [ 309.448867] RIP: 0010:[<ffffffffc0080d4f>] [<ffffffffc0080d4f>]
> pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
> [ 309.458765] RSP: 0018:ffff880404fa7cd8 EFLAGS: 00010286
> [ 309.464145] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000006e02
> [ 309.471342] RDX: 0000000000000000 RSI: 0000000000000286 RDI: ffff880403e98000
> [ 309.478546] RBP: ffff880404fa7d18 R08: ffff880404fa4000 R09: 0000000000000000
> [ 309.485749] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8804022b8000
> [ 309.492954] R13: ffff880403e98000 R14: ffff880401b80180 R15: 0000000000000000
> [ 309.500163] FS: 0000000000000000(0000) GS:ffff88041fd40000(0000)
> knlGS:0000000000000000
> [ 309.508337] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> [ 309.514147] CR2: 0000000000000290 CR3: 0000000001c16000 CR4: 00000000001407e0
> [ 309.521348] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
> [ 309.528551] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
> [ 309.535752] Stack:
> [ 309.537837] ffff8804022b8000 ffff880401bbe000 ffff880401b80180
> ffff880403e98000
> [ 309.545599] ffff8804022b8000 ffff880401bbe000 ffff880401b80180
> 0000000000000000
> [ 309.553349] ffff880404fa7d78 ffffffffc00826e8 ffff880404fa7d78
> ffffffff810ababc
> [ 309.561091] Call Trace:
> [ 309.563611] [<ffffffffc00826e8>]
> pm8001_I_T_nexus_event_handler+0xb8/0x1f0 [pm80xx]
> [ 309.571449] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
> [ 309.577355] [<ffffffffc0084559>] pm8001_work_fn+0x299/0x480 [pm80xx]
> [ 309.583869] [<ffffffff8108ce6f>] process_one_work+0x17f/0x490
> [ 309.589773] [<ffffffff8108d7eb>] worker_thread+0x11b/0x3f0
> [ 309.595413] [<ffffffff8108d6d0>] ? create_worker+0x1e0/0x1e0
> [ 309.601225] [<ffffffff81093349>] kthread+0xc9/0xe0
> [ 309.606176] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
> [ 309.612421] [<ffffffff817a3f3c>] ret_from_fork+0x7c/0xb0
> [ 309.617890] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
> [ 309.624135] Code: 00 55 48 89 e5 48 83 ec 40 4c 89 6d e8 4c 89 75
> f0 49 89 fd 4c 89 7d f8 48 89 5d d8 4c 89 65 e0 48 8b 47 30 48
> 8b 9f 78 01 00 00 <48> 8b 80 90 02 00 00 4c 8b a0 90 01 00 00 4d 8d 74
> 24 38 4c 89
> [ 309.647551] RIP [<ffffffffc0080d4f>]
> pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
> [ 309.655100] RSP <ffff880404fa7cd8>
> [ 309.658657] CR2: 0000000000000290
> [ 309.662045] ---[ end trace 084eaa8941942e9a ]---
> [ 309.770413] BUG: unable to handle kernel paging request at ffffffffffffffd8
> [ 309.777578] IP: [<ffffffff810936e0>] kthread_data+0x10/0x20
> [ 309.783287] PGD 1c19067 PUD 1c1b067 PMD 0
> [ 309.787652] Oops: 0000 [#2] SMP
> [ 309.791080] Modules linked in: ipmi_devintf autofs4 arc4 nfsd
> auth_rpcgss intel_rapl nfs_acl x86_pkg_temp_thermal nfs
> intel_powerclamp coretemp lockd kvm_intel sunrpc kvm fscache
> crct10dif_pclmul ttm crc32_pclmul drm_kms_helper rt2800usb
> ghash_clmulni_intel rt2x00usb rt2800lib rt2x00lib mac80211 aesni_intel
> drm aes_x86_64 lrw gf128mul glue_helper ablk_helper cfg80211 cryptd
> crc_ccitt syscopyarea joydev sysfillrect sysimgblt shpchp lpc_ich
> ipmi_si ipmi_msghandler mac_hid video ie31200_edac edac_core lp
> parport ses enclosure hid_generic usbhid hid raid10 raid456
> async_raid6_recov async_memcpy async_pq async_xor async_tx xor igb
> raid6_pq i2c_algo_bit raid1 e1000e pm80xx dca raid0 libsas ahci ptp
> multipath scsi_transport_sas libahci pps_core linear
> [ 309.862627] CPU: 5 PID: 1998 Comm: kworker/5:2 Tainted: G D
> 3.17.0-031700rc3-generic #201409031132
> [ 309.872709] Hardware name: Supermicro X10SLL-F/X10SLL-F, BIOS 2.0 04/24/2014
> [ 309.879834] task: ffff880403690000 ti: ffff880404fa4000 task.ti:
> ffff880404fa4000
> [ 309.887407] RIP: 0010:[<ffffffff810936e0>] [<ffffffff810936e0>]
> kthread_data+0x10/0x20
> [ 309.895562] RSP: 0018:ffff880404fa78e8 EFLAGS: 00010092
> [ 309.900939] RAX: 0000000000000000 RBX: 0000000000000005 RCX: ffffffff81ec2e80
> [ 309.908139] RDX: 0000000000000000 RSI: 0000000000000005 RDI: ffff880403690000
> [ 309.915343] RBP: ffff880404fa78e8 R08: 0000000000000000 R09: 0000000000000246
> [ 309.922549] R10: 000000000000001a R11: 0000000000000013 R12: 0000000000000005
> [ 309.929749] R13: ffff880403690538 R14: 0000000000000001 R15: 0000000000000046
> [ 309.936953] FS: 0000000000000000(0000) GS:ffff88041fd40000(0000)
> knlGS:0000000000000000
> [ 309.945130] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> [ 309.950942] CR2: 0000000000000028 CR3: 0000000001c16000 CR4: 00000000001407e0
> [ 309.958140] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
> [ 309.965345] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
> [ 309.972548] Stack:
> [ 309.974632] ffff880404fa7908 ffffffff8108e725 ffff880404fa7908
> ffff88041fd545c0
> [ 309.982368] ffff880404fa7988 ffffffff8179f8b3 ffff880404fa7948
> ffff880403690000
> [ 309.990110] ffff880404fa7fd8 00000000000145c0 ffff880404fa7948
> 00000000000145c0
> [ 309.997858] Call Trace:
> [ 310.000377] [<ffffffff8108e725>] wq_worker_sleeping+0x15/0xb0
> [ 310.006281] [<ffffffff8179f8b3>] __schedule+0x5e3/0x770
> [ 310.011666] [<ffffffff8179fb19>] schedule+0x29/0x70
> [ 310.016704] [<ffffffff81077795>] do_exit+0x2a5/0x470
> [ 310.021830] [<ffffffff810c9fbc>] ? kmsg_dump+0x9c/0xc0
> [ 310.027128] [<ffffffff81018d08>] oops_end+0xb8/0x160
> [ 310.032253] [<ffffffff81788489>] no_context+0x1be/0x1cd
> [ 310.037631] [<ffffffff8178866b>] __bad_area_nosemaphore+0x1d3/0x1f2
> [ 310.044059] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
> [ 310.049962] [<ffffffff8178869d>] bad_area_nosemaphore+0x13/0x15
> [ 310.056043] [<ffffffff81062312>] __do_page_fault+0x3b2/0x550
> [ 310.061856] [<ffffffff810ae3aa>] ? idle_balance+0x7a/0x2c0
> [ 310.067493] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
> [ 310.073399] [<ffffffff810135c6>] ? __switch_to+0xf6/0x5b0
> [ 310.078960] [<ffffffff8106263e>] do_page_fault+0x3e/0x80
> [ 310.084431] [<ffffffff817a6088>] page_fault+0x28/0x30
> [ 310.089643] [<ffffffffc0080d4f>] ?
> pm8001_dev_gone_notify+0x2f/0x220 [pm80xx]
> [ 310.096957] [<ffffffffc00826e8>]
> pm8001_I_T_nexus_event_handler+0xb8/0x1f0 [pm80xx]
> [ 310.104791] [<ffffffff810ababc>] ? put_prev_entity+0x3c/0x320
> [ 310.110691] [<ffffffffc0084559>] pm8001_work_fn+0x299/0x480 [pm80xx]
> [ 310.117205] [<ffffffff8108ce6f>] process_one_work+0x17f/0x490
> [ 310.123106] [<ffffffff8108d7eb>] worker_thread+0x11b/0x3f0
> [ 310.128752] [<ffffffff8108d6d0>] ? create_worker+0x1e0/0x1e0
> [ 310.134572] [<ffffffff81093349>] kthread+0xc9/0xe0
> [ 310.139519] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
> [ 310.145763] [<ffffffff817a3f3c>] ret_from_fork+0x7c/0xb0
> [ 310.151227] [<ffffffff81093280>] ? flush_kthread_worker+0x90/0x90
> [ 310.157473] Code: 00 48 89 e5 5d 48 8b 40 c8 48 c1 e8 02 83 e0 01
> c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8b 87 c8 04 00 00
> 55 48 89 e5 <48> 8b 40 d8 5d c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44
> 00 00
> [ 310.180886] RIP [<ffffffff810936e0>] kthread_data+0x10/0x20
> [ 310.186679] RSP <ffff880404fa78e8>
> [ 310.190239] CR2: ffffffffffffffd8
> [ 310.193623] ---[ end trace 084eaa8941942e9b ]---
> [ 310.306147] Fixing recursive fault but reboot is needed!
>
>
> On Wed, Sep 3, 2014 at 12:06 AM, Emmanuel Florac <eflorac@intellique.com> wrote:
>> Le Mon, 1 Sep 2014 09:06:46 -0700
>> Andrew Robertson <andyrobertson101@gmail.com> écrivait:
>>
>>> I'm happy to test patches/etc on this system if necessary -- and/or if
>>> someone can help point me in the right direction, I'd appreciate it.
>>
>> In my experience the 7xxx5 are very sensitive to cable length and
>> backplane type: basically work fine with 50 cm cables, and fails with 80
>> cm cables with some backplanes (works with Supermicro, not with AIC,
>> etc).
>>
>> So what is the backplane and cables you're using?
>>
>> --
>> ------------------------------------------------------------------------
>> Emmanuel Florac | Direction technique
>> | Intellique
>> | <eflorac@intellique.com>
>> | +33 1 78 94 84 02
>> ------------------------------------------------------------------------
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2015-05-18 19:19 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <CAKmTNed2uSUGCDkxQSLofjgSGxLpZ154_gNpwt_NWChjR=s8iA@mail.gmail.com>
2014-09-01 16:06 ` Fwd: Adaptec 71605H HBA randomly failing to detect any drives at init Andrew Robertson
2014-09-02 13:28 ` Suresh Thiagarajan
2014-09-02 14:06 ` Emmanuel Florac
2014-09-05 22:13 ` Andrew Robertson
2014-09-06 5:32 ` Fwd: " Andrew Robertson
2015-05-18 19:19 ` Andrew Robertson
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.