* [PATCH] ARM: dts: imx6sx: add vining-2000 board support
@ 2017-08-31 16:06 ` Christoph Fritz
0 siblings, 0 replies; 14+ messages in thread
From: Christoph Fritz @ 2017-08-31 16:06 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: devicetree, linux-arm-kernel, open-source
Add initial imx6sx-softing-vining-2000 board support.
Signed-off-by: Christoph Fritz <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6sx-softing-vining-2000.dts | 575 +++++++++++++++++++++++
2 files changed, 576 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4b17f35..0d9673d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-sdb-reva.dtb \
imx6sx-sdb-sai.dtb \
imx6sx-sdb.dtb \
+ imx6sx-softing-vining-2000.dtb \
imx6sx-udoo-neo-basic.dtb \
imx6sx-udoo-neo-extended.dtb \
imx6sx-udoo-neo-full.dtb
diff --git a/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
new file mode 100644
index 0000000..3db15f7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
@@ -0,0 +1,575 @@
+/*
+ * Copyright (C) 2016 Christoph Fritz
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sx.dtsi"
+
+/ {
+ model = "Softing VIN|ING 2000";
+ compatible = "softing,imx6sx-vining-2000", "fsl,imx6sx";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usb_otg1_vbus: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_peri_3v3: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "peri_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+
+ red {
+ label = "red";
+ max-brightness = <255>;
+ pwms = <&pwm6 0 50000>;
+ };
+
+ green {
+ label = "green";
+ max-brightness = <255>;
+ pwms = <&pwm2 0 50000>;
+ };
+
+ blue {
+ label = "blue";
+ max-brightness = <255>;
+ pwms = <&pwm1 0 50000>;
+ };
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-supply = <®_peri_3v3>;
+ phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <5>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet0-phy@0 {
+ reg = <0>;
+ max-speed = <100>;
+ interrupts-parent = <&gpio2>;
+ interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-supply = <®_peri_3v3>;
+ phy-reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <5>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet1-phy@0 {
+ reg = <0>;
+ max-speed = <100>;
+ interrupts-parent = <&gpio2>;
+ interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&pwm6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm6>;
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2_50mhz>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ cd-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ status = "okay";
+};
+
+&usdhc4 {
+ /* hs200-mode is currently unsupported because Vccq is on 3.1V, but
+ * not on necessary 1.8V.
+ */
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc4_50mhz>;
+ pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+ bus-width = <8>;
+ keep-power-in-suspend;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpios>;
+
+ pinctrl_gpios: gpiosgrp {
+ fsl,pins = <
+ /* reset external uC */
+ MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19 0x80000000
+ /* IRQ from external uC */
+ MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x80000000
+ /* overcurrent detection */
+ MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8 0x80000000
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1B_DQS__CAN1_TX 0x1b0b0
+ MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX 0x1b0b0
+ MX6SX_PAD_QSPI1A_DQS__CAN2_TX 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x30c1
+ MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x30c1
+ MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0f9
+ MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0f9
+ MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x30c1
+ MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0f9
+ MX6SX_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4000a038
+ /* LAN8720 PHY Reset */
+ MX6SX_PAD_RGMII1_TD3__GPIO5_IO_9 0x80000000
+ /* MDIO */
+ MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0f9
+ MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0f9
+ /* IRQ from PHY */
+ MX6SX_PAD_KEY_ROW2__GPIO2_IO_17 0x80000000
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0x1b0b0
+ MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0x1b0b0
+ MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x1b0b0
+ MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x1b0b0
+ MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x1b0b0
+ MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0x1b0b0
+ MX6SX_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4000a038
+ /* LAN8720 PHY Reset */
+ MX6SX_PAD_RGMII2_TD3__GPIO5_IO_21 0x80000000
+ /* MDIO */
+ MX6SX_PAD_ENET1_COL__ENET2_MDC 0xa0f9
+ MX6SX_PAD_ENET1_CRS__ENET2_MDIO 0xa0f9
+ /* IRQ from PHY */
+ MX6SX_PAD_KEY_ROW4__GPIO2_IO_19 0x80000000
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp-1 {
+ fsl,pins = <
+ /* blue LED */
+ MX6SX_PAD_RGMII2_RD3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp-1 {
+ fsl,pins = <
+ /* green LED */
+ MX6SX_PAD_RGMII2_RD2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm6: pwm6grp-1 {
+ fsl,pins = <
+ /* red LED */
+ MX6SX_PAD_RGMII2_TD2__PWM6_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CLK__ECSPI4_SCLK 0x130b1
+ MX6SX_PAD_SD3_DATA3__ECSPI4_MISO 0x130b1
+ MX6SX_PAD_SD3_CMD__ECSPI4_MOSI 0x130b1
+ MX6SX_PAD_SD3_DATA2__GPIO7_IO_4 0x80000000
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO01__I2C1_SDA 0x4001b8b1
+ MX6SX_PAD_GPIO1_IO00__I2C1_SCL 0x4001b8b1
+ >;
+ };
+ pinctrl_sx9500: sx9500grp {
+ fsl,pins = <
+ /* Reset */
+ MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x838
+ /* IRQ */
+ MX6SX_PAD_KEY_ROW1__GPIO2_IO_16 0x80000000
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6SX_PAD_NAND_ALE__I2C3_SDA 0x4001b8b1
+ MX6SX_PAD_NAND_CLE__I2C3_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO06__UART2_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO07__UART2_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x10b0
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_50mhz: usdhc2grp-50mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x10059
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x17059
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x17059
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x17059
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x17059
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x17059
+ MX6SX_PAD_LCD1_VSYNC__GPIO3_IO_28 0x80000000
+ MX6SX_PAD_LCD1_HSYNC__GPIO3_IO_26 0x80000000
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100b9
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170b9
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170b9
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170b9
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170b9
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100f9
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170f9
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170f9
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170f9
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170f9
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc4_50mhz: usdhc4grp-50mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x17059
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x17059
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x17059
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x17059
+ MX6SX_PAD_SD4_RESET_B__USDHC4_RESET_B 0x17068
+ >;
+ };
+
+ pinctrl_usdhc4_100mhz: usdhc4-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100b9
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170b9
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170b9
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170b9
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170b9
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170b9
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170b9
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170b9
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170b9
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc4_200mhz: usdhc4-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100f9
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170f9
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170f9
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170f9
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170f9
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170f9
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170f9
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170f9
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170f9
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170f9
+ >;
+ };
+};
+
+&cpu0 {
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ proximity: sx9500@28 {
+ compatible = "semtech,sx9500";
+ reg = <0x28>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sx9500>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ pmic: pfuze100@08 {
+ compatible = "fsl,pfuze200";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+®_arm {
+ vin-supply = <&sw1a_reg>;
+};
+
+®_soc {
+ vin-supply = <&sw1a_reg>;
+};
+
+&ecspi4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio7 4 0>;
+ status = "okay";
+};
+
+&adc1 {
+ vref-supply = <®_peri_3v3>;
+ status = "okay";
+};
+
+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH] ARM: dts: imx6sx: add vining-2000 board support
@ 2017-08-31 16:06 ` Christoph Fritz
0 siblings, 0 replies; 14+ messages in thread
From: Christoph Fritz @ 2017-08-31 16:06 UTC (permalink / raw)
To: linux-arm-kernel
Add initial imx6sx-softing-vining-2000 board support.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6sx-softing-vining-2000.dts | 575 +++++++++++++++++++++++
2 files changed, 576 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4b17f35..0d9673d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-sdb-reva.dtb \
imx6sx-sdb-sai.dtb \
imx6sx-sdb.dtb \
+ imx6sx-softing-vining-2000.dtb \
imx6sx-udoo-neo-basic.dtb \
imx6sx-udoo-neo-extended.dtb \
imx6sx-udoo-neo-full.dtb
diff --git a/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
new file mode 100644
index 0000000..3db15f7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
@@ -0,0 +1,575 @@
+/*
+ * Copyright (C) 2016 Christoph Fritz
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sx.dtsi"
+
+/ {
+ model = "Softing VIN|ING 2000";
+ compatible = "softing,imx6sx-vining-2000", "fsl,imx6sx";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usb_otg1_vbus: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_peri_3v3: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "peri_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+
+ red {
+ label = "red";
+ max-brightness = <255>;
+ pwms = <&pwm6 0 50000>;
+ };
+
+ green {
+ label = "green";
+ max-brightness = <255>;
+ pwms = <&pwm2 0 50000>;
+ };
+
+ blue {
+ label = "blue";
+ max-brightness = <255>;
+ pwms = <&pwm1 0 50000>;
+ };
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-supply = <®_peri_3v3>;
+ phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <5>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet0-phy at 0 {
+ reg = <0>;
+ max-speed = <100>;
+ interrupts-parent = <&gpio2>;
+ interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-supply = <®_peri_3v3>;
+ phy-reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <5>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet1-phy at 0 {
+ reg = <0>;
+ max-speed = <100>;
+ interrupts-parent = <&gpio2>;
+ interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&pwm6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm6>;
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2_50mhz>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ cd-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ status = "okay";
+};
+
+&usdhc4 {
+ /* hs200-mode is currently unsupported because Vccq is on 3.1V, but
+ * not on necessary 1.8V.
+ */
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc4_50mhz>;
+ pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+ bus-width = <8>;
+ keep-power-in-suspend;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpios>;
+
+ pinctrl_gpios: gpiosgrp {
+ fsl,pins = <
+ /* reset external uC */
+ MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19 0x80000000
+ /* IRQ from external uC */
+ MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x80000000
+ /* overcurrent detection */
+ MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8 0x80000000
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1B_DQS__CAN1_TX 0x1b0b0
+ MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX 0x1b0b0
+ MX6SX_PAD_QSPI1A_DQS__CAN2_TX 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x30c1
+ MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x30c1
+ MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0f9
+ MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0f9
+ MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x30c1
+ MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0f9
+ MX6SX_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4000a038
+ /* LAN8720 PHY Reset */
+ MX6SX_PAD_RGMII1_TD3__GPIO5_IO_9 0x80000000
+ /* MDIO */
+ MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0f9
+ MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0f9
+ /* IRQ from PHY */
+ MX6SX_PAD_KEY_ROW2__GPIO2_IO_17 0x80000000
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0x1b0b0
+ MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0x1b0b0
+ MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x1b0b0
+ MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x1b0b0
+ MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x1b0b0
+ MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0x1b0b0
+ MX6SX_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4000a038
+ /* LAN8720 PHY Reset */
+ MX6SX_PAD_RGMII2_TD3__GPIO5_IO_21 0x80000000
+ /* MDIO */
+ MX6SX_PAD_ENET1_COL__ENET2_MDC 0xa0f9
+ MX6SX_PAD_ENET1_CRS__ENET2_MDIO 0xa0f9
+ /* IRQ from PHY */
+ MX6SX_PAD_KEY_ROW4__GPIO2_IO_19 0x80000000
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp-1 {
+ fsl,pins = <
+ /* blue LED */
+ MX6SX_PAD_RGMII2_RD3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp-1 {
+ fsl,pins = <
+ /* green LED */
+ MX6SX_PAD_RGMII2_RD2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm6: pwm6grp-1 {
+ fsl,pins = <
+ /* red LED */
+ MX6SX_PAD_RGMII2_TD2__PWM6_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CLK__ECSPI4_SCLK 0x130b1
+ MX6SX_PAD_SD3_DATA3__ECSPI4_MISO 0x130b1
+ MX6SX_PAD_SD3_CMD__ECSPI4_MOSI 0x130b1
+ MX6SX_PAD_SD3_DATA2__GPIO7_IO_4 0x80000000
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO01__I2C1_SDA 0x4001b8b1
+ MX6SX_PAD_GPIO1_IO00__I2C1_SCL 0x4001b8b1
+ >;
+ };
+ pinctrl_sx9500: sx9500grp {
+ fsl,pins = <
+ /* Reset */
+ MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x838
+ /* IRQ */
+ MX6SX_PAD_KEY_ROW1__GPIO2_IO_16 0x80000000
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6SX_PAD_NAND_ALE__I2C3_SDA 0x4001b8b1
+ MX6SX_PAD_NAND_CLE__I2C3_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO06__UART2_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO07__UART2_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x10b0
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_50mhz: usdhc2grp-50mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x10059
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x17059
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x17059
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x17059
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x17059
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x17059
+ MX6SX_PAD_LCD1_VSYNC__GPIO3_IO_28 0x80000000
+ MX6SX_PAD_LCD1_HSYNC__GPIO3_IO_26 0x80000000
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100b9
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170b9
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170b9
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170b9
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170b9
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100f9
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170f9
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170f9
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170f9
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170f9
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc4_50mhz: usdhc4grp-50mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x17059
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x17059
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x17059
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x17059
+ MX6SX_PAD_SD4_RESET_B__USDHC4_RESET_B 0x17068
+ >;
+ };
+
+ pinctrl_usdhc4_100mhz: usdhc4-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100b9
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170b9
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170b9
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170b9
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170b9
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170b9
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170b9
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170b9
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170b9
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc4_200mhz: usdhc4-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100f9
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170f9
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170f9
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170f9
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170f9
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170f9
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170f9
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170f9
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170f9
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170f9
+ >;
+ };
+};
+
+&cpu0 {
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ proximity: sx9500 at 28 {
+ compatible = "semtech,sx9500";
+ reg = <0x28>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sx9500>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ pmic: pfuze100 at 08 {
+ compatible = "fsl,pfuze200";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+®_arm {
+ vin-supply = <&sw1a_reg>;
+};
+
+®_soc {
+ vin-supply = <&sw1a_reg>;
+};
+
+&ecspi4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio7 4 0>;
+ status = "okay";
+};
+
+&adc1 {
+ vref-supply = <®_peri_3v3>;
+ status = "okay";
+};
+
+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH] ARM: dts: imx6sx: add vining-2000 board support
2017-08-31 16:06 ` Christoph Fritz
@ 2017-09-01 12:17 ` Fabio Estevam
-1 siblings, 0 replies; 14+ messages in thread
From: Fabio Estevam @ 2017-09-01 12:17 UTC (permalink / raw)
To: Christoph Fritz
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, devicetree,
linux-arm-kernel, open-source
Hi Christoph,
On Thu, Aug 31, 2017 at 1:06 PM, Christoph Fritz
<chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org> wrote:
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
> @@ -0,0 +1,575 @@
> +/*
> + * Copyright (C) 2016 Christoph Fritz
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
Please consider using dual license GPL/X11 license.
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "imx6sx.dtsi"
> +
> +/ {
> + model = "Softing VIN|ING 2000";
> + compatible = "softing,imx6sx-vining-2000", "fsl,imx6sx";
I see the following entry in
Documentation/devicetree/bindings/vendor-prefixes.txt:
samtec Samtec/Softing company
Could you use "samtec,imx6sx-vining-2000" instead?
> +
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + memory {
> + reg = <0x80000000 0x40000000>;
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
No need to have this 'regulators' node.
> +
> + reg_usb_otg1_vbus: regulator@0 {
Please use the same regulator pattern as in
arch/arm/boot/dts/imx6q-tbs2910.dts, for example.
> +&fec2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet2>;
> + phy-supply = <®_peri_3v3>;
> + phy-reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <5>;
> + phy-mode = "rmii";
> + phy-handle = <ðphy1>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet1-phy@0 {
> + reg = <0>;
> + max-speed = <100>;
> + interrupts-parent = <&gpio2>;
> + interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +};
> +
> +&i2c3 {
Keep the nodes in alphabetical order.
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpios>;
> +
> + pinctrl_gpios: gpiosgrp {
> + fsl,pins = <
> + /* reset external uC */
> + MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19 0x80000000
> + /* IRQ from external uC */
> + MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x80000000
> + /* overcurrent detection */
> + MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8 0x80000000
Do not use 0x80000000. Better use the real IOMUX value instead. Same
applies to other IOMUX instances.
> +&cpu0 {
> + operating-points = <
> + /* kHz uV */
> + 996000 1250000
> + 792000 1175000
> + 396000 1175000
> + 198000 1175000
> + >;
> + fsl,soc-operating-points = <
> + /* ARM kHz SOC uV */
> + 996000 1250000
> + 792000 1175000
> + 396000 1175000
> + 198000 1175000
> + >;
It would be nice to add a comment as to why the operating points from
imx6sx.dtsi can't be used.
> +&ecspi4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi4>;
> + fsl,spi-num-chipselects = <1>;
This property has been deprecated, so remove it.
> + cs-gpios = <&gpio7 4 0>;
Is this really active high? Please double check and use proper GPIO
flags GPIO_ACTIVE_HIGH/LOW.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] ARM: dts: imx6sx: add vining-2000 board support
@ 2017-09-01 12:17 ` Fabio Estevam
0 siblings, 0 replies; 14+ messages in thread
From: Fabio Estevam @ 2017-09-01 12:17 UTC (permalink / raw)
To: linux-arm-kernel
Hi Christoph,
On Thu, Aug 31, 2017 at 1:06 PM, Christoph Fritz
<chf.fritz@googlemail.com> wrote:
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
> @@ -0,0 +1,575 @@
> +/*
> + * Copyright (C) 2016 Christoph Fritz
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
Please consider using dual license GPL/X11 license.
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "imx6sx.dtsi"
> +
> +/ {
> + model = "Softing VIN|ING 2000";
> + compatible = "softing,imx6sx-vining-2000", "fsl,imx6sx";
I see the following entry in
Documentation/devicetree/bindings/vendor-prefixes.txt:
samtec Samtec/Softing company
Could you use "samtec,imx6sx-vining-2000" instead?
> +
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + memory {
> + reg = <0x80000000 0x40000000>;
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
No need to have this 'regulators' node.
> +
> + reg_usb_otg1_vbus: regulator at 0 {
Please use the same regulator pattern as in
arch/arm/boot/dts/imx6q-tbs2910.dts, for example.
> +&fec2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet2>;
> + phy-supply = <®_peri_3v3>;
> + phy-reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <5>;
> + phy-mode = "rmii";
> + phy-handle = <ðphy1>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet1-phy at 0 {
> + reg = <0>;
> + max-speed = <100>;
> + interrupts-parent = <&gpio2>;
> + interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +};
> +
> +&i2c3 {
Keep the nodes in alphabetical order.
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpios>;
> +
> + pinctrl_gpios: gpiosgrp {
> + fsl,pins = <
> + /* reset external uC */
> + MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19 0x80000000
> + /* IRQ from external uC */
> + MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x80000000
> + /* overcurrent detection */
> + MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8 0x80000000
Do not use 0x80000000. Better use the real IOMUX value instead. Same
applies to other IOMUX instances.
> +&cpu0 {
> + operating-points = <
> + /* kHz uV */
> + 996000 1250000
> + 792000 1175000
> + 396000 1175000
> + 198000 1175000
> + >;
> + fsl,soc-operating-points = <
> + /* ARM kHz SOC uV */
> + 996000 1250000
> + 792000 1175000
> + 396000 1175000
> + 198000 1175000
> + >;
It would be nice to add a comment as to why the operating points from
imx6sx.dtsi can't be used.
> +&ecspi4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi4>;
> + fsl,spi-num-chipselects = <1>;
This property has been deprecated, so remove it.
> + cs-gpios = <&gpio7 4 0>;
Is this really active high? Please double check and use proper GPIO
flags GPIO_ACTIVE_HIGH/LOW.
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2] ARM: dts: imx6sx: add vining-2000 board support
2017-09-01 12:17 ` Fabio Estevam
@ 2017-09-03 9:35 ` Christoph Fritz
-1 siblings, 0 replies; 14+ messages in thread
From: Christoph Fritz @ 2017-09-03 9:35 UTC (permalink / raw)
To: Fabio Estevam; +Cc: Shawn Guo, Sascha Hauer, devicetree, linux-arm-kernel
Add initial imx6sx-softing-vining-2000 board support.
Signed-off-by: Christoph Fritz <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
---
Changes since v1:
- considered and declined X11 license
- compat string changed to samtec Samtec/Softing company
- purged deprecated 'regulators' node
- unify regulator pattern
- keep nodes in alphabetical order
- change 0x80000000 iomux to real value
- add comment to cpu0 node
- remove deprecated spi-num-chipselects
- use name instead of number for ecspi4 CS
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6sx-softing-vining-2000.dts | 572 +++++++++++++++++++++++
2 files changed, 573 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4b17f35..0d9673d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-sdb-reva.dtb \
imx6sx-sdb-sai.dtb \
imx6sx-sdb.dtb \
+ imx6sx-softing-vining-2000.dtb \
imx6sx-udoo-neo-basic.dtb \
imx6sx-udoo-neo-extended.dtb \
imx6sx-udoo-neo-full.dtb
diff --git a/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
new file mode 100644
index 0000000..ee012bc
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
@@ -0,0 +1,572 @@
+/*
+ * Copyright (C) 2016 Christoph Fritz <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sx.dtsi"
+
+/ {
+ model = "Softing VIN|ING 2000";
+ compatible = "samtec,imx6sx-vining-2000", "fsl,imx6sx";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ reg_usb_otg1_vbus: regulator-usb_otg1_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_peri_3v3: regulator-peri_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "peri_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+
+ red {
+ label = "red";
+ max-brightness = <255>;
+ pwms = <&pwm6 0 50000>;
+ };
+
+ green {
+ label = "green";
+ max-brightness = <255>;
+ pwms = <&pwm2 0 50000>;
+ };
+
+ blue {
+ label = "blue";
+ max-brightness = <255>;
+ pwms = <&pwm1 0 50000>;
+ };
+ };
+};
+
+&adc1 {
+ vref-supply = <®_peri_3v3>;
+ status = "okay";
+};
+
+&cpu0 {
+ /*
+ * This board has a shared rail of reg_arm and reg_soc (supplied by
+ * sw1a_reg) which is modeled below, but still this module behaves
+ * unstable without higher voltages. Hence, set higher voltages here.
+ */
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+};
+
+&ecspi4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ cs-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-supply = <®_peri_3v3>;
+ phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <5>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet0-phy@0 {
+ reg = <0>;
+ max-speed = <100>;
+ interrupts-parent = <&gpio2>;
+ interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-supply = <®_peri_3v3>;
+ phy-reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <5>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet1-phy@0 {
+ reg = <0>;
+ max-speed = <100>;
+ interrupts-parent = <&gpio2>;
+ interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ proximity: sx9500@28 {
+ compatible = "semtech,sx9500";
+ reg = <0x28>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sx9500>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ pmic: pfuze100@08 {
+ compatible = "fsl,pfuze200";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpios>;
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CLK__ECSPI4_SCLK 0x130b1
+ MX6SX_PAD_SD3_DATA3__ECSPI4_MISO 0x130b1
+ MX6SX_PAD_SD3_CMD__ECSPI4_MOSI 0x130b1
+ MX6SX_PAD_SD3_DATA2__GPIO7_IO_4 0x30b0
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x30c1
+ MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x30c1
+ MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0f9
+ MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0f9
+ MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x30c1
+ MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0f9
+ MX6SX_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4000a038
+ /* LAN8720 PHY Reset */
+ MX6SX_PAD_RGMII1_TD3__GPIO5_IO_9 0x10b0
+ /* MDIO */
+ MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0f9
+ MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0f9
+ /* IRQ from PHY */
+ MX6SX_PAD_KEY_ROW2__GPIO2_IO_17 0x10b0
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0x1b0b0
+ MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0x1b0b0
+ MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x1b0b0
+ MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x1b0b0
+ MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x1b0b0
+ MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0x1b0b0
+ MX6SX_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4000a038
+ /* LAN8720 PHY Reset */
+ MX6SX_PAD_RGMII2_TD3__GPIO5_IO_21 0x10b0
+ /* MDIO */
+ MX6SX_PAD_ENET1_COL__ENET2_MDC 0xa0f9
+ MX6SX_PAD_ENET1_CRS__ENET2_MDIO 0xa0f9
+ /* IRQ from PHY */
+ MX6SX_PAD_KEY_ROW4__GPIO2_IO_19 0x10b0
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1B_DQS__CAN1_TX 0x1b0b0
+ MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX 0x1b0b0
+ MX6SX_PAD_QSPI1A_DQS__CAN2_TX 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpios: gpiosgrp {
+ fsl,pins = <
+ /* reset external uC */
+ MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19 0x10b0
+ /* IRQ from external uC */
+ MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x10b0
+ /* overcurrent detection */
+ MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8 0x10b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO01__I2C1_SDA 0x4001b8b1
+ MX6SX_PAD_GPIO1_IO00__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6SX_PAD_NAND_ALE__I2C3_SDA 0x4001b8b1
+ MX6SX_PAD_NAND_CLE__I2C3_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp-1 {
+ fsl,pins = <
+ /* blue LED */
+ MX6SX_PAD_RGMII2_RD3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp-1 {
+ fsl,pins = <
+ /* green LED */
+ MX6SX_PAD_RGMII2_RD2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm6: pwm6grp-1 {
+ fsl,pins = <
+ /* red LED */
+ MX6SX_PAD_RGMII2_TD2__PWM6_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_sx9500: sx9500grp {
+ fsl,pins = <
+ /* Reset */
+ MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x838
+ /* IRQ */
+ MX6SX_PAD_KEY_ROW1__GPIO2_IO_16 0x70e0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO06__UART2_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO07__UART2_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x10b0
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_50mhz: usdhc2grp-50mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x10059
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x17059
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x17059
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x17059
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x17059
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x17059
+ MX6SX_PAD_LCD1_VSYNC__GPIO3_IO_28 0x1b000
+ MX6SX_PAD_LCD1_HSYNC__GPIO3_IO_26 0x10b0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100b9
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170b9
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170b9
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170b9
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170b9
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100f9
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170f9
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170f9
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170f9
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170f9
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc4_50mhz: usdhc4grp-50mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x17059
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x17059
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x17059
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x17059
+ MX6SX_PAD_SD4_RESET_B__USDHC4_RESET_B 0x17068
+ >;
+ };
+
+ pinctrl_usdhc4_100mhz: usdhc4-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100b9
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170b9
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170b9
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170b9
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170b9
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170b9
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170b9
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170b9
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170b9
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc4_200mhz: usdhc4-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100f9
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170f9
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170f9
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170f9
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170f9
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170f9
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170f9
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170f9
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170f9
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170f9
+ >;
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&pwm6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm6>;
+ status = "okay";
+};
+
+®_arm {
+ vin-supply = <&sw1a_reg>;
+};
+
+®_soc {
+ vin-supply = <&sw1a_reg>;
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2_50mhz>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ cd-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ status = "okay";
+};
+
+&usdhc4 {
+ /* hs200-mode is currently unsupported because Vccq is on 3.1V, but
+ * not on necessary 1.8V.
+ */
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc4_50mhz>;
+ pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+ bus-width = <8>;
+ keep-power-in-suspend;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2] ARM: dts: imx6sx: add vining-2000 board support
@ 2017-09-03 9:35 ` Christoph Fritz
0 siblings, 0 replies; 14+ messages in thread
From: Christoph Fritz @ 2017-09-03 9:35 UTC (permalink / raw)
To: linux-arm-kernel
Add initial imx6sx-softing-vining-2000 board support.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
---
Changes since v1:
- considered and declined X11 license
- compat string changed to samtec Samtec/Softing company
- purged deprecated 'regulators' node
- unify regulator pattern
- keep nodes in alphabetical order
- change 0x80000000 iomux to real value
- add comment to cpu0 node
- remove deprecated spi-num-chipselects
- use name instead of number for ecspi4 CS
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6sx-softing-vining-2000.dts | 572 +++++++++++++++++++++++
2 files changed, 573 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4b17f35..0d9673d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-sdb-reva.dtb \
imx6sx-sdb-sai.dtb \
imx6sx-sdb.dtb \
+ imx6sx-softing-vining-2000.dtb \
imx6sx-udoo-neo-basic.dtb \
imx6sx-udoo-neo-extended.dtb \
imx6sx-udoo-neo-full.dtb
diff --git a/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
new file mode 100644
index 0000000..ee012bc
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
@@ -0,0 +1,572 @@
+/*
+ * Copyright (C) 2016 Christoph Fritz <chf.fritz@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sx.dtsi"
+
+/ {
+ model = "Softing VIN|ING 2000";
+ compatible = "samtec,imx6sx-vining-2000", "fsl,imx6sx";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ reg_usb_otg1_vbus: regulator-usb_otg1_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_peri_3v3: regulator-peri_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "peri_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+
+ red {
+ label = "red";
+ max-brightness = <255>;
+ pwms = <&pwm6 0 50000>;
+ };
+
+ green {
+ label = "green";
+ max-brightness = <255>;
+ pwms = <&pwm2 0 50000>;
+ };
+
+ blue {
+ label = "blue";
+ max-brightness = <255>;
+ pwms = <&pwm1 0 50000>;
+ };
+ };
+};
+
+&adc1 {
+ vref-supply = <®_peri_3v3>;
+ status = "okay";
+};
+
+&cpu0 {
+ /*
+ * This board has a shared rail of reg_arm and reg_soc (supplied by
+ * sw1a_reg) which is modeled below, but still this module behaves
+ * unstable without higher voltages. Hence, set higher voltages here.
+ */
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+};
+
+&ecspi4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ cs-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-supply = <®_peri_3v3>;
+ phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <5>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet0-phy at 0 {
+ reg = <0>;
+ max-speed = <100>;
+ interrupts-parent = <&gpio2>;
+ interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-supply = <®_peri_3v3>;
+ phy-reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <5>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet1-phy at 0 {
+ reg = <0>;
+ max-speed = <100>;
+ interrupts-parent = <&gpio2>;
+ interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ proximity: sx9500 at 28 {
+ compatible = "semtech,sx9500";
+ reg = <0x28>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sx9500>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ pmic: pfuze100 at 08 {
+ compatible = "fsl,pfuze200";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpios>;
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CLK__ECSPI4_SCLK 0x130b1
+ MX6SX_PAD_SD3_DATA3__ECSPI4_MISO 0x130b1
+ MX6SX_PAD_SD3_CMD__ECSPI4_MOSI 0x130b1
+ MX6SX_PAD_SD3_DATA2__GPIO7_IO_4 0x30b0
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x30c1
+ MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x30c1
+ MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0f9
+ MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0f9
+ MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x30c1
+ MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0f9
+ MX6SX_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4000a038
+ /* LAN8720 PHY Reset */
+ MX6SX_PAD_RGMII1_TD3__GPIO5_IO_9 0x10b0
+ /* MDIO */
+ MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0f9
+ MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0f9
+ /* IRQ from PHY */
+ MX6SX_PAD_KEY_ROW2__GPIO2_IO_17 0x10b0
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0x1b0b0
+ MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0x1b0b0
+ MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x1b0b0
+ MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x1b0b0
+ MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x1b0b0
+ MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0x1b0b0
+ MX6SX_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4000a038
+ /* LAN8720 PHY Reset */
+ MX6SX_PAD_RGMII2_TD3__GPIO5_IO_21 0x10b0
+ /* MDIO */
+ MX6SX_PAD_ENET1_COL__ENET2_MDC 0xa0f9
+ MX6SX_PAD_ENET1_CRS__ENET2_MDIO 0xa0f9
+ /* IRQ from PHY */
+ MX6SX_PAD_KEY_ROW4__GPIO2_IO_19 0x10b0
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1B_DQS__CAN1_TX 0x1b0b0
+ MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX 0x1b0b0
+ MX6SX_PAD_QSPI1A_DQS__CAN2_TX 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpios: gpiosgrp {
+ fsl,pins = <
+ /* reset external uC */
+ MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19 0x10b0
+ /* IRQ from external uC */
+ MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x10b0
+ /* overcurrent detection */
+ MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8 0x10b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO01__I2C1_SDA 0x4001b8b1
+ MX6SX_PAD_GPIO1_IO00__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6SX_PAD_NAND_ALE__I2C3_SDA 0x4001b8b1
+ MX6SX_PAD_NAND_CLE__I2C3_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp-1 {
+ fsl,pins = <
+ /* blue LED */
+ MX6SX_PAD_RGMII2_RD3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp-1 {
+ fsl,pins = <
+ /* green LED */
+ MX6SX_PAD_RGMII2_RD2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm6: pwm6grp-1 {
+ fsl,pins = <
+ /* red LED */
+ MX6SX_PAD_RGMII2_TD2__PWM6_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_sx9500: sx9500grp {
+ fsl,pins = <
+ /* Reset */
+ MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x838
+ /* IRQ */
+ MX6SX_PAD_KEY_ROW1__GPIO2_IO_16 0x70e0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO06__UART2_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO07__UART2_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x10b0
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_50mhz: usdhc2grp-50mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x10059
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x17059
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x17059
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x17059
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x17059
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x17059
+ MX6SX_PAD_LCD1_VSYNC__GPIO3_IO_28 0x1b000
+ MX6SX_PAD_LCD1_HSYNC__GPIO3_IO_26 0x10b0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100b9
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170b9
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170b9
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170b9
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170b9
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100f9
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170f9
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170f9
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170f9
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170f9
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc4_50mhz: usdhc4grp-50mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x17059
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x17059
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x17059
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x17059
+ MX6SX_PAD_SD4_RESET_B__USDHC4_RESET_B 0x17068
+ >;
+ };
+
+ pinctrl_usdhc4_100mhz: usdhc4-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100b9
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170b9
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170b9
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170b9
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170b9
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170b9
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170b9
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170b9
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170b9
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc4_200mhz: usdhc4-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100f9
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170f9
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170f9
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170f9
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170f9
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170f9
+ MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170f9
+ MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170f9
+ MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170f9
+ MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170f9
+ >;
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&pwm6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm6>;
+ status = "okay";
+};
+
+®_arm {
+ vin-supply = <&sw1a_reg>;
+};
+
+®_soc {
+ vin-supply = <&sw1a_reg>;
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2_50mhz>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ cd-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ status = "okay";
+};
+
+&usdhc4 {
+ /* hs200-mode is currently unsupported because Vccq is on 3.1V, but
+ * not on necessary 1.8V.
+ */
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc4_50mhz>;
+ pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+ bus-width = <8>;
+ keep-power-in-suspend;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v2] ARM: dts: imx6sx: add vining-2000 board support
2017-09-03 9:35 ` Christoph Fritz
@ 2017-09-09 10:20 ` Christoph Fritz
-1 siblings, 0 replies; 14+ messages in thread
From: Christoph Fritz @ 2017-09-09 10:20 UTC (permalink / raw)
To: Fabio Estevam
Cc: Shawn Guo, Sascha Hauer, devicetree, linux-arm-kernel, open-source
On Sun, 2017-09-03 at 11:35 +0200, Christoph Fritz wrote:
> Add initial imx6sx-softing-vining-2000 board support.
>
> Signed-off-by: Christoph Fritz <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
> ---
Hi Fabio,
can I get your ack on patch v2 or do you have further annotations?
thanks
-- Christoph
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2] ARM: dts: imx6sx: add vining-2000 board support
@ 2017-09-09 10:20 ` Christoph Fritz
0 siblings, 0 replies; 14+ messages in thread
From: Christoph Fritz @ 2017-09-09 10:20 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, 2017-09-03 at 11:35 +0200, Christoph Fritz wrote:
> Add initial imx6sx-softing-vining-2000 board support.
>
> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
> ---
Hi Fabio,
can I get your ack on patch v2 or do you have further annotations?
thanks
-- Christoph
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH] ARM: dts: imx6sx: add vining-2000 board support
2017-08-31 16:06 ` Christoph Fritz
@ 2017-09-09 11:36 ` Fabio Estevam
-1 siblings, 0 replies; 14+ messages in thread
From: Fabio Estevam @ 2017-09-09 11:36 UTC (permalink / raw)
To: Christoph Fritz
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, devicetree,
linux-arm-kernel, open-source
Hi Christoph,
On Thu, Aug 31, 2017 at 1:06 PM, Christoph Fritz
<chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org> wrote:
> Add initial imx6sx-softing-vining-2000 board support.
>
> Signed-off-by: Christoph Fritz <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] ARM: dts: imx6sx: add vining-2000 board support
@ 2017-09-09 11:36 ` Fabio Estevam
0 siblings, 0 replies; 14+ messages in thread
From: Fabio Estevam @ 2017-09-09 11:36 UTC (permalink / raw)
To: linux-arm-kernel
Hi Christoph,
On Thu, Aug 31, 2017 at 1:06 PM, Christoph Fritz
<chf.fritz@googlemail.com> wrote:
> Add initial imx6sx-softing-vining-2000 board support.
>
> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH] ARM: dts: imx6sx: add vining-2000 board support
2017-09-09 11:36 ` Fabio Estevam
@ 2017-09-09 13:31 ` Christoph Fritz
-1 siblings, 0 replies; 14+ messages in thread
From: Christoph Fritz @ 2017-09-09 13:31 UTC (permalink / raw)
To: Shawn Guo
Cc: Sascha Hauer, Fabio Estevam, devicetree, linux-arm-kernel, open-source
On Sat, 2017-09-09 at 08:36 -0300, Fabio Estevam wrote:
> Hi Christoph,
>
> On Thu, Aug 31, 2017 at 1:06 PM, Christoph Fritz
> <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org> wrote:
> > Add initial imx6sx-softing-vining-2000 board support.
> >
> > Signed-off-by: Christoph Fritz <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
>
> Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
Thanks
@Shawn: Would you pick this patch?
-- Christoph
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] ARM: dts: imx6sx: add vining-2000 board support
@ 2017-09-09 13:31 ` Christoph Fritz
0 siblings, 0 replies; 14+ messages in thread
From: Christoph Fritz @ 2017-09-09 13:31 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, 2017-09-09 at 08:36 -0300, Fabio Estevam wrote:
> Hi Christoph,
>
> On Thu, Aug 31, 2017 at 1:06 PM, Christoph Fritz
> <chf.fritz@googlemail.com> wrote:
> > Add initial imx6sx-softing-vining-2000 board support.
> >
> > Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
>
> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Thanks
@Shawn: Would you pick this patch?
-- Christoph
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2] ARM: dts: imx6sx: add vining-2000 board support
2017-09-03 9:35 ` Christoph Fritz
@ 2017-09-22 5:32 ` Shawn Guo
-1 siblings, 0 replies; 14+ messages in thread
From: Shawn Guo @ 2017-09-22 5:32 UTC (permalink / raw)
To: Christoph Fritz; +Cc: Fabio Estevam, Sascha Hauer, devicetree, linux-arm-kernel
On Sun, Sep 03, 2017 at 11:35:11AM +0200, Christoph Fritz wrote:
> Add initial imx6sx-softing-vining-2000 board support.
>
> Signed-off-by: Christoph Fritz <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
Applied, thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2] ARM: dts: imx6sx: add vining-2000 board support
@ 2017-09-22 5:32 ` Shawn Guo
0 siblings, 0 replies; 14+ messages in thread
From: Shawn Guo @ 2017-09-22 5:32 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Sep 03, 2017 at 11:35:11AM +0200, Christoph Fritz wrote:
> Add initial imx6sx-softing-vining-2000 board support.
>
> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Applied, thanks.
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2017-09-22 5:32 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-08-31 16:06 [PATCH] ARM: dts: imx6sx: add vining-2000 board support Christoph Fritz
2017-08-31 16:06 ` Christoph Fritz
[not found] ` <1504195599.1918.17.camel-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
2017-09-01 12:17 ` Fabio Estevam
2017-09-01 12:17 ` Fabio Estevam
[not found] ` <CAOMZO5BSvyJCSGVF_7EOqia=ufX77JTkQwDCeey8kEaqDB_PBA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-09-03 9:35 ` [PATCH v2] " Christoph Fritz
2017-09-03 9:35 ` Christoph Fritz
[not found] ` <1504431311.1939.11.camel-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
2017-09-09 10:20 ` Christoph Fritz
2017-09-09 10:20 ` Christoph Fritz
2017-09-22 5:32 ` Shawn Guo
2017-09-22 5:32 ` Shawn Guo
2017-09-09 11:36 ` [PATCH] " Fabio Estevam
2017-09-09 11:36 ` Fabio Estevam
[not found] ` <CAOMZO5ALWF4WJomwFfKpO0pROd2dkSXeBM1bXFmV-V5jEeSSRQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-09-09 13:31 ` Christoph Fritz
2017-09-09 13:31 ` Christoph Fritz
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.