[PATCH 0/6] Add driver support for NXP IMX8QXP ADC

[PATCH 0/6] Add driver support for NXP IMX8QXP ADC

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP. These patches add
driver support for this ADC.

Cai Huoqing (6):
  iio: adc: Init the driver for NXP i.MX8QuadXPlus
  iio: adc: Add configuration for NXP i.MX8QuadXPlus ADC driver
  iio: imx8qxp-adc: Add the detail for NXP i.MX8QuadXPlus ADC driver
  dt-bindings: iio: adc: Add the binding documentation for NXP IMX8QXP
    ADC
  MAINTAINERS: Add the driver info of the NXP IMX8QXP ADC
  iio: imx8qxp-adc: Add the copyright for NXP i.MX8QuadXPlus ADC driver

 .../bindings/iio/adc/nxp,imx8qxp-adc.yaml     |  85 +++
 MAINTAINERS                                   |   7 +
 drivers/iio/adc/Kconfig                       |  10 +
 drivers/iio/adc/Makefile                      |   1 +
 drivers/iio/adc/imx8qxp-adc.c                 | 588 ++++++++++++++++++
 5 files changed, 691 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
 create mode 100644 drivers/iio/adc/imx8qxp-adc.c

-- 
2.25.1

[PATCH 0/6] Add driver support for NXP IMX8QXP ADC

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP. These patches add
driver support for this ADC.

Cai Huoqing (6):
  iio: adc: Init the driver for NXP i.MX8QuadXPlus
  iio: adc: Add configuration for NXP i.MX8QuadXPlus ADC driver
  iio: imx8qxp-adc: Add the detail for NXP i.MX8QuadXPlus ADC driver
  dt-bindings: iio: adc: Add the binding documentation for NXP IMX8QXP
    ADC
  MAINTAINERS: Add the driver info of the NXP IMX8QXP ADC
  iio: imx8qxp-adc: Add the copyright for NXP i.MX8QuadXPlus ADC driver

 .../bindings/iio/adc/nxp,imx8qxp-adc.yaml     |  85 +++
 MAINTAINERS                                   |   7 +
 drivers/iio/adc/Kconfig                       |  10 +
 drivers/iio/adc/Makefile                      |   1 +
 drivers/iio/adc/imx8qxp-adc.c                 | 588 ++++++++++++++++++
 5 files changed, 691 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
 create mode 100644 drivers/iio/adc/imx8qxp-adc.c

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/6] iio: adc: Init the driver for NXP i.MX8QuadXPlus

[Cai Huoqing]

ADC

The NXP i.MX 8QuadXPlus SOC has a new ADC IP. This patch init
this ADC driver.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 drivers/iio/adc/imx8qxp-adc.c | 67 +++++++++++++++++++++++++++++++++++
 1 file changed, 67 insertions(+)
 create mode 100644 drivers/iio/adc/imx8qxp-adc.c

diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
new file mode 100644
index 000000000000..aec1b45c8fb9
--- /dev/null
+++ b/drivers/iio/adc/imx8qxp-adc.c
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * NXP i.MX8QXP ADC driver
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/driver.h>
+#include <linux/iio/sysfs.h>
+
+#define ADC_DRIVER_NAME		"imx8qxp-adc"
+
+static int imx8qxp_adc_probe(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static int imx8qxp_adc_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static int imx8qxp_adc_runtime_suspend(struct device *dev)
+{
+	return 0;
+}
+
+static int imx8qxp_adc_runtime_resume(struct device *dev)
+{
+	return 0;
+}
+
+static const struct dev_pm_ops imx8qxp_adc_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(imx8qxp_adc_runtime_suspend, imx8qxp_adc_runtime_resume, NULL)
+};
+
+static const struct of_device_id imx8qxp_adc_match[] = {
+	{ .compatible = "nxp,imx8qxp-adc", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx8qxp_adc_match);
+
+static struct platform_driver imx8qxp_adc_driver = {
+	.probe		= imx8qxp_adc_probe,
+	.remove		= imx8qxp_adc_remove,
+	.driver		= {
+		.name	= ADC_DRIVER_NAME,
+		.of_match_table = imx8qxp_adc_match,
+		.pm	= &imx8qxp_adc_pm_ops,
+	},
+};
+
+module_platform_driver(imx8qxp_adc_driver);
+
+MODULE_DESCRIPTION("i.MX8QuadXPlus ADC driver");
+MODULE_LICENSE("GPL v2");
-- 
2.25.1

[PATCH 1/6] iio: adc: Init the driver for NXP i.MX8QuadXPlus

[Cai Huoqing]

ADC

The NXP i.MX 8QuadXPlus SOC has a new ADC IP. This patch init
this ADC driver.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 drivers/iio/adc/imx8qxp-adc.c | 67 +++++++++++++++++++++++++++++++++++
 1 file changed, 67 insertions(+)
 create mode 100644 drivers/iio/adc/imx8qxp-adc.c

diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
new file mode 100644
index 000000000000..aec1b45c8fb9
--- /dev/null
+++ b/drivers/iio/adc/imx8qxp-adc.c
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * NXP i.MX8QXP ADC driver
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/driver.h>
+#include <linux/iio/sysfs.h>
+
+#define ADC_DRIVER_NAME		"imx8qxp-adc"
+
+static int imx8qxp_adc_probe(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static int imx8qxp_adc_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static int imx8qxp_adc_runtime_suspend(struct device *dev)
+{
+	return 0;
+}
+
+static int imx8qxp_adc_runtime_resume(struct device *dev)
+{
+	return 0;
+}
+
+static const struct dev_pm_ops imx8qxp_adc_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(imx8qxp_adc_runtime_suspend, imx8qxp_adc_runtime_resume, NULL)
+};
+
+static const struct of_device_id imx8qxp_adc_match[] = {
+	{ .compatible = "nxp,imx8qxp-adc", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx8qxp_adc_match);
+
+static struct platform_driver imx8qxp_adc_driver = {
+	.probe		= imx8qxp_adc_probe,
+	.remove		= imx8qxp_adc_remove,
+	.driver		= {
+		.name	= ADC_DRIVER_NAME,
+		.of_match_table = imx8qxp_adc_match,
+		.pm	= &imx8qxp_adc_pm_ops,
+	},
+};
+
+module_platform_driver(imx8qxp_adc_driver);
+
+MODULE_DESCRIPTION("i.MX8QuadXPlus ADC driver");
+MODULE_LICENSE("GPL v2");
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/6] iio: adc: Init the driver for NXP i.MX8QuadXPlus

[Fabio Estevam]

Hi Cai,

On Mon, Aug 30, 2021 at 2:22 PM Cai Huoqing <caihuoqing@baidu.com> wrote:

> +static int imx8qxp_adc_probe(struct platform_device *pdev)
> +{
> +       return 0;
> +}

This is not the correct way to split the series.

Patches 1, 2, 3, and 5 could be squashed into a single patch.

Thanks

Re: [PATCH 1/6] iio: adc: Init the driver for NXP i.MX8QuadXPlus

[Fabio Estevam]

Hi Cai,

On Mon, Aug 30, 2021 at 2:22 PM Cai Huoqing <caihuoqing@baidu.com> wrote:

> +static int imx8qxp_adc_probe(struct platform_device *pdev)
> +{
> +       return 0;
> +}

This is not the correct way to split the series.

Patches 1, 2, 3, and 5 could be squashed into a single patch.

Thanks

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/6] iio: adc: Init the driver for NXP i.MX8QuadXPlus

[Jonathan Cameron]

On Tue, 31 Aug 2021 01:21:35 +0800
Cai Huoqing <caihuoqing@baidu.com> wrote:

> ADC
> 
> The NXP i.MX 8QuadXPlus SOC has a new ADC IP. This patch init
> this ADC driver.
> 
> Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
> ---
>  drivers/iio/adc/imx8qxp-adc.c | 67 +++++++++++++++++++++++++++++++++++
>  1 file changed, 67 insertions(+)
>  create mode 100644 drivers/iio/adc/imx8qxp-adc.c
> 
> diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
> new file mode 100644
> index 000000000000..aec1b45c8fb9
> --- /dev/null
> +++ b/drivers/iio/adc/imx8qxp-adc.c
> @@ -0,0 +1,67 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * NXP i.MX8QXP ADC driver
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/completion.h>
> +#include <linux/err.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/delay.h>
> +#include <linux/module.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/driver.h>
> +#include <linux/iio/sysfs.h>
A good example of why you shouldn't have had so many small patches is
that reviewers want to look at a patch on it's own. In this case
we can't tell if you are going to use these headers later or not.
Hence review is more complex.

I'll have a brief go at reviewing, but reality is a real review needs
to be easier to do than it is here!

I will note though that alphabetical order, perhaps with iio includes
in their own block is preferred for headers in IIO drivers.


> +
> +#define ADC_DRIVER_NAME		"imx8qxp-adc"
> +
> +static int imx8qxp_adc_probe(struct platform_device *pdev)
> +{
> +	return 0;
> +}
> +
> +static int imx8qxp_adc_remove(struct platform_device *pdev)
> +{
> +	return 0;
> +}
> +
> +static int imx8qxp_adc_runtime_suspend(struct device *dev)
> +{
> +	return 0;
> +}
> +
> +static int imx8qxp_adc_runtime_resume(struct device *dev)
> +{
> +	return 0;
> +}
> +
> +static const struct dev_pm_ops imx8qxp_adc_pm_ops = {
> +	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, pm_runtime_force_resume)
> +	SET_RUNTIME_PM_OPS(imx8qxp_adc_runtime_suspend, imx8qxp_adc_runtime_resume, NULL)
> +};
> +
> +static const struct of_device_id imx8qxp_adc_match[] = {
> +	{ .compatible = "nxp,imx8qxp-adc", },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, imx8qxp_adc_match);
> +
> +static struct platform_driver imx8qxp_adc_driver = {
> +	.probe		= imx8qxp_adc_probe,
> +	.remove		= imx8qxp_adc_remove,
> +	.driver		= {
> +		.name	= ADC_DRIVER_NAME,
> +		.of_match_table = imx8qxp_adc_match,
> +		.pm	= &imx8qxp_adc_pm_ops,
> +	},
> +};
> +
> +module_platform_driver(imx8qxp_adc_driver);
> +
> +MODULE_DESCRIPTION("i.MX8QuadXPlus ADC driver");
> +MODULE_LICENSE("GPL v2");

Re: [PATCH 1/6] iio: adc: Init the driver for NXP i.MX8QuadXPlus

[Jonathan Cameron]

On Tue, 31 Aug 2021 01:21:35 +0800
Cai Huoqing <caihuoqing@baidu.com> wrote:

> ADC
> 
> The NXP i.MX 8QuadXPlus SOC has a new ADC IP. This patch init
> this ADC driver.
> 
> Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
> ---
>  drivers/iio/adc/imx8qxp-adc.c | 67 +++++++++++++++++++++++++++++++++++
>  1 file changed, 67 insertions(+)
>  create mode 100644 drivers/iio/adc/imx8qxp-adc.c
> 
> diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
> new file mode 100644
> index 000000000000..aec1b45c8fb9
> --- /dev/null
> +++ b/drivers/iio/adc/imx8qxp-adc.c
> @@ -0,0 +1,67 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * NXP i.MX8QXP ADC driver
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/completion.h>
> +#include <linux/err.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/delay.h>
> +#include <linux/module.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/driver.h>
> +#include <linux/iio/sysfs.h>
A good example of why you shouldn't have had so many small patches is
that reviewers want to look at a patch on it's own. In this case
we can't tell if you are going to use these headers later or not.
Hence review is more complex.

I'll have a brief go at reviewing, but reality is a real review needs
to be easier to do than it is here!

I will note though that alphabetical order, perhaps with iio includes
in their own block is preferred for headers in IIO drivers.


> +
> +#define ADC_DRIVER_NAME		"imx8qxp-adc"
> +
> +static int imx8qxp_adc_probe(struct platform_device *pdev)
> +{
> +	return 0;
> +}
> +
> +static int imx8qxp_adc_remove(struct platform_device *pdev)
> +{
> +	return 0;
> +}
> +
> +static int imx8qxp_adc_runtime_suspend(struct device *dev)
> +{
> +	return 0;
> +}
> +
> +static int imx8qxp_adc_runtime_resume(struct device *dev)
> +{
> +	return 0;
> +}
> +
> +static const struct dev_pm_ops imx8qxp_adc_pm_ops = {
> +	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, pm_runtime_force_resume)
> +	SET_RUNTIME_PM_OPS(imx8qxp_adc_runtime_suspend, imx8qxp_adc_runtime_resume, NULL)
> +};
> +
> +static const struct of_device_id imx8qxp_adc_match[] = {
> +	{ .compatible = "nxp,imx8qxp-adc", },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, imx8qxp_adc_match);
> +
> +static struct platform_driver imx8qxp_adc_driver = {
> +	.probe		= imx8qxp_adc_probe,
> +	.remove		= imx8qxp_adc_remove,
> +	.driver		= {
> +		.name	= ADC_DRIVER_NAME,
> +		.of_match_table = imx8qxp_adc_match,
> +		.pm	= &imx8qxp_adc_pm_ops,
> +	},
> +};
> +
> +module_platform_driver(imx8qxp_adc_driver);
> +
> +MODULE_DESCRIPTION("i.MX8QuadXPlus ADC driver");
> +MODULE_LICENSE("GPL v2");


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/6] iio: adc: Add configuration for NXP i.MX8QuadXPlus ADC driver

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the configuration
for NXP i.MX8QuadXPlus ADC driver.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 drivers/iio/adc/Kconfig  | 10 ++++++++++
 drivers/iio/adc/Makefile |  1 +
 2 files changed, 11 insertions(+)

diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index af168e1c9fdb..fa8ad63d6ac2 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -530,6 +530,16 @@ config IMX7D_ADC
 	  This driver can also be built as a module. If so, the module will be
 	  called imx7d_adc.
 
+config IMX8QXP_ADC
+	tristate "NXP IMX8QXP ADC driver"
+	depends on ARCH_MXC_ARM64 || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  Say yes here to build support for IMX8QXP ADC.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called imx8qxp-adc.
+
 config LP8788_ADC
 	tristate "LP8788 ADC driver"
 	depends on MFD_LP8788
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index d68550f493e3..d3f53549720c 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
 obj-$(CONFIG_HI8435) += hi8435.o
 obj-$(CONFIG_HX711) += hx711.o
 obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
+obj-$(CONFIG_IMX8QXP_ADC) += imx8qxp-adc.o
 obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
 obj-$(CONFIG_INGENIC_ADC) += ingenic-adc.o
 obj-$(CONFIG_INTEL_MRFLD_ADC) += intel_mrfld_adc.o
-- 
2.25.1

[PATCH 2/6] iio: adc: Add configuration for NXP i.MX8QuadXPlus ADC driver

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the configuration
for NXP i.MX8QuadXPlus ADC driver.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 drivers/iio/adc/Kconfig  | 10 ++++++++++
 drivers/iio/adc/Makefile |  1 +
 2 files changed, 11 insertions(+)

diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index af168e1c9fdb..fa8ad63d6ac2 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -530,6 +530,16 @@ config IMX7D_ADC
 	  This driver can also be built as a module. If so, the module will be
 	  called imx7d_adc.
 
+config IMX8QXP_ADC
+	tristate "NXP IMX8QXP ADC driver"
+	depends on ARCH_MXC_ARM64 || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  Say yes here to build support for IMX8QXP ADC.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called imx8qxp-adc.
+
 config LP8788_ADC
 	tristate "LP8788 ADC driver"
 	depends on MFD_LP8788
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index d68550f493e3..d3f53549720c 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
 obj-$(CONFIG_HI8435) += hi8435.o
 obj-$(CONFIG_HX711) += hx711.o
 obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
+obj-$(CONFIG_IMX8QXP_ADC) += imx8qxp-adc.o
 obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
 obj-$(CONFIG_INGENIC_ADC) += ingenic-adc.o
 obj-$(CONFIG_INTEL_MRFLD_ADC) += intel_mrfld_adc.o
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/6] iio: imx8qxp-adc: Add the detail for NXP i.MX8QuadXPlus ADC driver

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the detail for NXP
i.MX8QuadXPlus ADC driver which includes: probe/remove/pm_ops/iio_dev.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 drivers/iio/adc/imx8qxp-adc.c | 513 ++++++++++++++++++++++++++++++++++
 1 file changed, 513 insertions(+)

diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
index aec1b45c8fb9..d39bf382c582 100644
--- a/drivers/iio/adc/imx8qxp-adc.c
+++ b/drivers/iio/adc/imx8qxp-adc.c
@@ -20,23 +20,536 @@
 
 #define ADC_DRIVER_NAME		"imx8qxp-adc"
 
+/* Register map definition */
+#define ADC_CTRL		0x10
+#define ADC_STAT		0x14
+#define ADC_IE			0x18
+#define ADC_DE			0x1c
+#define ADC_CFG			0x20
+#define ADC_FCTRL		0x30
+#define ADC_SWTRIG		0x34
+#define ADC_TCTRL(tid)		(0xc0 + tid * 4)
+#define ADC_CMDH(cid)		(0x100 + cid * 8)
+#define ADC_CMDL(cid)		(0x104 + cid * 8)
+#define ADC_RESFIFO		0x300
+#define ADC_TST			0xffc
+
+/* ADC bit shift */
+#define ADC_IE_FWMIE_SHIFT		(0)
+#define ADC_CTRL_FIFO_RESET_SHIFT	(8)
+#define ADC_CTRL_SOFTWARE_RESET_SHIFT	(1)
+#define ADC_CTRL_ADC_ENABLE		(0)
+#define ADC_TCTRL_TCMD_SHIFT		(24)
+#define ADC_TCTRL_TDLY_SHIFT		(16)
+#define ADC_TCTRL_TPRI_SHIFT		(8)
+#define ADC_TCTRL_HTEN_SHIFT		(0)
+#define ADC_CMDL_CSCALE_SHIFT		(8)
+#define ADC_CMDL_MODE_SHIFT		(7)
+#define ADC_CMDL_DIFF_SHIFT		(6)
+#define ADC_CMDL_ABSEL_SHIFT		(5)
+#define ADC_CMDL_ADCH_SHIFT		(0)
+#define ADC_CMDH_NEXT_SHIFT		(24)
+#define ADC_CMDH_LOOP_SHIFT		(16)
+#define ADC_CMDH_AVGS_SHIFT		(12)
+#define ADC_CMDH_STS_SHIFT		(8)
+#define ADC_CMDH_LWI_SHIFT		(7)
+#define ADC_CMDH_CMPEN_SHIFT		(0)
+#define ADC_CFG_PWREN_SHIFT		(28)
+#define ADC_CFG_PUDLY_SHIFT		(16)
+#define ADC_CFG_REFSEL_SHIFT		(6)
+#define ADC_CFG_PWRSEL_SHIFT		(4)
+#define ADC_CFG_TPRICTRL_SHIFT		(0)
+#define ADC_FCTRL_FWMARK_SHIFT		(16)
+#define ADC_FCTRL_FWMARK_MASK		(0x1f << 16)
+#define ADC_FCTRL_FCOUNT_MASK		(0x1f)
+
+/* ADC PARAMETER*/
+#define ADC_CMDL_CHANNEL_SCALE_FULL		(0x3f)
+#define ADC_CMDL_SEL_A_A_B_CHANNEL		(0)
+#define ADC_CMDL_STANDARD_RESOLUTION		(0)
+#define ADC_CMDL_MODE_SINGLE			(0)
+#define ADC_CMDH_LWI_INCREMENT_DISABLE		(0)
+#define ADC_CMDH_CMPEN_DISABLE			(0)
+#define ADC_PAUSE_ENABLE			(0x80000000)
+#define ADC_TCTRL_TPRI_PRIORITY_HIGH		(0)
+
+#define ADC_TCTRL_HTEN_HARDWARE_TIRGGER_DISABLE	(0)
+
+#define MAX_CMD (8)
+#define MAX_TRIG (8)
+
+#define ADC_TIMEOUT		msecs_to_jiffies(100)
+
+struct imx8qxp_adc_trigger_ctrl {
+	u32 tcmd;
+	u32 tdly;
+	u32 tpri;
+	u32 hten;
+};
+
+struct imx8qxp_adc_cmd_l {
+	u32 scale;
+	u32 mode;
+	u32 diff;
+	u32 absel;
+	u32 adch;
+};
+
+struct imx8qxp_adc_cmd_h {
+	u32 next;
+	u32 loop;
+	u32 avgs;
+	u32 sts;
+	u32 lwi;
+	u32 cmpen;
+};
+
+struct imx8qxp_adc_cfg {
+	u32 pwren;
+	u32 pudly;
+	u32 refsel;
+	u32 pwrsel;
+	u32 tprictrl;
+};
+
+struct imx8qxp_adc {
+	struct device *dev;
+	void __iomem *regs;
+	struct clk *clk;
+	struct clk *ipg_clk;
+
+	u32 vref_uv;
+	u32 value;
+	u32 channel_id;
+	u32 trigger_id;
+	u32 cmd_id;
+
+	struct regulator *vref;
+	struct imx8qxp_adc_cmd_l adc_cmd_l[MAX_CMD + 1];
+	struct imx8qxp_adc_cmd_h adc_cmd_h[MAX_CMD + 1];
+	struct imx8qxp_adc_trigger_ctrl adc_trigger_ctrl[MAX_TRIG + 1];
+	struct imx8qxp_adc_cfg adc_cfg;
+	struct completion completion;
+};
+
+#define IMX8QXP_ADC_CHAN(_idx) {				\
+	.type = IIO_VOLTAGE,					\
+	.indexed = 1,						\
+	.channel = (_idx),					\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
+	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) |	\
+				BIT(IIO_CHAN_INFO_SAMP_FREQ),	\
+}
+
+static const struct iio_chan_spec imx8qxp_adc_iio_channels[] = {
+	IMX8QXP_ADC_CHAN(0),
+	IMX8QXP_ADC_CHAN(1),
+	IMX8QXP_ADC_CHAN(2),
+	IMX8QXP_ADC_CHAN(3),
+	IMX8QXP_ADC_CHAN(4),
+	IMX8QXP_ADC_CHAN(5),
+	IMX8QXP_ADC_CHAN(6),
+	IMX8QXP_ADC_CHAN(7),
+};
+
+static void imx8qxp_adc_feature_prepare(struct imx8qxp_adc *adc)
+{
+	u32 i;
+
+	adc->trigger_id = 0;
+	adc->cmd_id = 0;
+	adc->channel_id = 0;
+
+	for (i = 0; i < MAX_CMD + 1; i++) {
+		adc->adc_cmd_l[i].scale = 1;
+		adc->adc_cmd_l[i].mode = 0;
+		adc->adc_cmd_l[i].diff = 0;
+		adc->adc_cmd_l[i].absel = 0;
+		adc->adc_cmd_l[i].adch = 0;
+		adc->adc_cmd_h[i].next = 0;
+		adc->adc_cmd_h[i].loop = 0;
+		adc->adc_cmd_h[i].avgs = 0;
+		adc->adc_cmd_h[i].sts = 0;
+		adc->adc_cmd_h[i].lwi = 0;
+		adc->adc_cmd_h[i].cmpen = 0;
+	}
+
+	for (i = 0; i < MAX_TRIG; i++) {
+		adc->adc_trigger_ctrl[i].tcmd = 0;
+		adc->adc_trigger_ctrl[i].tdly = 0;
+		adc->adc_trigger_ctrl[i].tpri = 0;
+		adc->adc_trigger_ctrl[i].hten = 0;
+	}
+
+	adc->adc_cfg.pwren = 0;
+	adc->adc_cfg.pudly = 0;
+	adc->adc_cfg.refsel = 0;
+	adc->adc_cfg.pwrsel = 0;
+	adc->adc_cfg.tprictrl = 0;
+}
+
+static void imx8qxp_adc_reset(struct imx8qxp_adc *adc)
+{
+	u32 ctrl;
+
+	/*software reset, need to clear the set bit*/
+	ctrl = readl(adc->regs + ADC_CTRL);
+	ctrl |= 1 << ADC_CTRL_SOFTWARE_RESET_SHIFT;
+	writel(ctrl, adc->regs + ADC_CTRL);
+	udelay(10);
+	ctrl &= ~(1 << ADC_CTRL_SOFTWARE_RESET_SHIFT);
+	writel(ctrl, adc->regs + ADC_CTRL);
+
+	/* reset the fifo */
+	ctrl |= 1 << ADC_CTRL_FIFO_RESET_SHIFT;
+	writel(ctrl, adc->regs + ADC_CTRL);
+}
+
+static void imx8qxp_adc_reg_config(struct imx8qxp_adc *adc)
+{
+	u32 adc_cfg, adc_tctrl, adc_cmdl, adc_cmdh;
+	u32 t_id, c_id;
+
+	adc_cfg = adc->adc_cfg.pwren << ADC_CFG_PWREN_SHIFT |
+		  adc->adc_cfg.pudly << ADC_CFG_PUDLY_SHIFT |
+		  adc->adc_cfg.refsel << ADC_CFG_REFSEL_SHIFT |
+		  adc->adc_cfg.pwrsel << ADC_CFG_PWRSEL_SHIFT |
+		  adc->adc_cfg.tprictrl << ADC_CFG_TPRICTRL_SHIFT;
+	writel(adc_cfg, adc->regs + ADC_CFG);
+
+	t_id = adc->trigger_id;
+	adc_tctrl = adc->adc_trigger_ctrl[t_id].tcmd << ADC_TCTRL_TCMD_SHIFT |
+		    adc->adc_trigger_ctrl[t_id].tdly << ADC_TCTRL_TDLY_SHIFT |
+		    adc->adc_trigger_ctrl[t_id].tpri << ADC_TCTRL_TPRI_SHIFT |
+		    adc->adc_trigger_ctrl[t_id].hten << ADC_TCTRL_HTEN_SHIFT;
+	writel(adc_tctrl, adc->regs + ADC_TCTRL(t_id));
+
+	c_id = adc->cmd_id - 1;
+	adc_cmdl = adc->adc_cmd_l[c_id].scale << ADC_CMDL_CSCALE_SHIFT |
+		   adc->adc_cmd_l[c_id].mode << ADC_CMDL_MODE_SHIFT |
+		   adc->adc_cmd_l[c_id].diff << ADC_CMDL_DIFF_SHIFT |
+		   adc->adc_cmd_l[c_id].absel << ADC_CMDL_ABSEL_SHIFT |
+		   adc->adc_cmd_l[c_id].adch << ADC_CMDL_ADCH_SHIFT;
+	writel(adc_cmdl, adc->regs + ADC_CMDL(c_id));
+
+	adc_cmdh = adc->adc_cmd_h[c_id].next << ADC_CMDH_NEXT_SHIFT |
+		   adc->adc_cmd_h[c_id].loop << ADC_CMDH_LOOP_SHIFT |
+		   adc->adc_cmd_h[c_id].avgs << ADC_CMDH_AVGS_SHIFT |
+		   adc->adc_cmd_h[c_id].sts << ADC_CMDH_STS_SHIFT |
+		   adc->adc_cmd_h[c_id].lwi << ADC_CMDH_LWI_SHIFT |
+		   adc->adc_cmd_h[c_id].cmpen << ADC_CMDH_CMPEN_SHIFT;
+	writel(adc_cmdh, adc->regs + ADC_CMDH(c_id));
+}
+
+static void imx8qxp_adc_mode_config(struct imx8qxp_adc *adc)
+{
+	u32 cmd_id, trigger_id, channel_id;
+
+	channel_id = adc->channel_id;
+	cmd_id = adc->cmd_id - 1;
+	trigger_id = adc->trigger_id;
+
+	/* config the cmd */
+	adc->adc_cmd_l[cmd_id].scale = ADC_CMDL_CHANNEL_SCALE_FULL;
+	adc->adc_cmd_l[cmd_id].mode = ADC_CMDL_STANDARD_RESOLUTION;
+	adc->adc_cmd_l[cmd_id].diff = ADC_CMDL_MODE_SINGLE;
+	adc->adc_cmd_l[cmd_id].absel = ADC_CMDL_SEL_A_A_B_CHANNEL;
+	adc->adc_cmd_l[cmd_id].adch = channel_id;
+
+	adc->adc_cmd_h[cmd_id].next = 0;
+	adc->adc_cmd_h[cmd_id].loop = 0;
+	adc->adc_cmd_h[cmd_id].avgs = 7;
+	adc->adc_cmd_h[cmd_id].sts = 0;
+	adc->adc_cmd_h[cmd_id].lwi = ADC_CMDH_LWI_INCREMENT_DISABLE;
+	adc->adc_cmd_h[cmd_id].cmpen = ADC_CMDH_CMPEN_DISABLE;
+
+	/* config the trigger control */
+	adc->adc_trigger_ctrl[trigger_id].tcmd = adc->cmd_id;
+	adc->adc_trigger_ctrl[trigger_id].tdly = 0;
+	adc->adc_trigger_ctrl[trigger_id].tpri = ADC_TCTRL_TPRI_PRIORITY_HIGH;
+	adc->adc_trigger_ctrl[trigger_id].hten = ADC_TCTRL_HTEN_HARDWARE_TIRGGER_DISABLE;
+
+	/* ADC configuration */
+	adc->adc_cfg.pwren = 1;
+	adc->adc_cfg.pudly = 0x80;
+	adc->adc_cfg.refsel = 0;
+	adc->adc_cfg.pwrsel = 3;
+	adc->adc_cfg.tprictrl = 0;
+
+	imx8qxp_adc_reg_config(adc);
+}
+
+static void imx8qxp_adc_fifo_config(struct imx8qxp_adc *adc)
+{
+	u32 fifo_ctrl, interrupt_en;
+
+	fifo_ctrl = readl(adc->regs + ADC_FCTRL);
+	fifo_ctrl &= ~ADC_FCTRL_FWMARK_MASK;
+	/* set the watermark level to 1 */
+	fifo_ctrl |= 0 << ADC_FCTRL_FWMARK_SHIFT;
+	writel(fifo_ctrl, adc->regs + ADC_FCTRL);
+
+	/* FIFO Watermark Interrupt Enable */
+	interrupt_en = readl(adc->regs + ADC_IE);
+	interrupt_en |= 1 << ADC_IE_FWMIE_SHIFT;
+	writel(interrupt_en, adc->regs + ADC_IE);
+}
+
+static void imx8qxp_adc_disable(struct imx8qxp_adc *adc)
+{
+	u32 ctrl;
+
+	ctrl = readl(adc->regs + ADC_CTRL) & ~(1 << ADC_CTRL_ADC_ENABLE);
+	writel(ctrl, adc->regs + ADC_CTRL);
+}
+
+static int imx8qxp_adc_read_raw(struct iio_dev *indio_dev, struct iio_chan_spec const *chan,
+				int *val, int *val2, long mask)
+{
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+	struct device *dev = adc->dev;
+
+	u32 channel;
+	u32 ctrl;
+	long ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		pm_runtime_get_sync(dev);
+
+		mutex_lock(&indio_dev->mlock);
+		reinit_completion(&adc->completion);
+
+		channel = chan->channel & 0x07;
+		adc->channel_id = channel;
+		adc->cmd_id = 1;
+		adc->trigger_id = 0;
+		imx8qxp_adc_mode_config(adc);
+
+		imx8qxp_adc_fifo_config(adc);
+
+		/* adc enable */
+		ctrl = readl(adc->regs + ADC_CTRL) | (1 << ADC_CTRL_ADC_ENABLE);
+		writel(ctrl, adc->regs + ADC_CTRL);
+		/* adc start */
+		writel(1 << adc->trigger_id, adc->regs + ADC_SWTRIG);
+
+		ret = wait_for_completion_interruptible_timeout
+				(&adc->completion, ADC_TIMEOUT);
+
+		pm_runtime_mark_last_busy(dev);
+		pm_runtime_put_sync_autosuspend(dev);
+
+		if (ret == 0) {
+			mutex_unlock(&indio_dev->mlock);
+			return -ETIMEDOUT;
+		}
+		if (ret < 0) {
+			mutex_unlock(&indio_dev->mlock);
+			return ret;
+		}
+
+		*val = adc->value;
+		mutex_unlock(&indio_dev->mlock);
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_SCALE:
+		adc->vref_uv = regulator_get_voltage(adc->vref);
+		*val = adc->vref_uv / 1000;
+		*val2 = 12;
+		return IIO_VAL_FRACTIONAL_LOG2;
+
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*val = clk_get_rate(adc->clk) / 3;
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
+static irqreturn_t imx8qxp_adc_isr(int irq, void *dev_id)
+{
+	struct imx8qxp_adc *adc = (struct imx8qxp_adc *)dev_id;
+
+	u32 fifo_count;
+
+	fifo_count = readl(adc->regs + ADC_FCTRL)
+			& ADC_FCTRL_FCOUNT_MASK;
+
+	if (fifo_count) {
+		adc->value = (readl(adc->regs + ADC_RESFIFO) & 0xffff) >> 3;
+		complete(&adc->completion);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int imx8qxp_adc_reg_access(struct iio_dev *indio_dev, unsigned int reg,
+				  unsigned int writeval, unsigned int *readval)
+{
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+	struct device *dev = adc->dev;
+
+	if (!readval || reg % 4 || reg > ADC_TST)
+		return -EINVAL;
+
+	pm_runtime_get_sync(dev);
+
+	*readval = readl(adc->regs + reg);
+
+	pm_runtime_mark_last_busy(dev);
+	pm_runtime_put_sync_autosuspend(dev);
+
+	return 0;
+}
+
+static const struct iio_info imx8qxp_adc_iio_info = {
+	.read_raw = &imx8qxp_adc_read_raw,
+	.debugfs_reg_access = &imx8qxp_adc_reg_access,
+};
+
 static int imx8qxp_adc_probe(struct platform_device *pdev)
 {
+	struct imx8qxp_adc *adc;
+	struct iio_dev *indio_dev;
+	struct device *dev = &pdev->dev;
+	int irq;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
+	if (!indio_dev) {
+		dev_err(dev, "Failed allocating iio device\n");
+		return -ENOMEM;
+	}
+
+	adc = iio_priv(indio_dev);
+	adc->dev = dev;
+
+	adc->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(adc->regs))
+		return PTR_ERR(adc->regs);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	adc->clk = devm_clk_get(dev, "per");
+	if (IS_ERR(adc->clk)) {
+		ret = PTR_ERR(adc->clk);
+		dev_err(dev, "Failed getting clock, err = %d\n", ret);
+		return ret;
+	}
+
+	adc->ipg_clk = devm_clk_get(dev, "ipg");
+	if (IS_ERR(adc->ipg_clk)) {
+		ret = PTR_ERR(adc->ipg_clk);
+		dev_err(dev, "Failed getting clock, err = %d\n", ret);
+		return ret;
+	}
+
+	adc->vref = devm_regulator_get(dev, "vref");
+	if (IS_ERR(adc->vref)) {
+		ret = PTR_ERR(adc->vref);
+		dev_err(dev,
+			"Failed getting reference voltage, err = %d\n", ret);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, indio_dev);
+
+	init_completion(&adc->completion);
+
+	indio_dev->name = dev_name(dev);
+	indio_dev->info = &imx8qxp_adc_iio_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = imx8qxp_adc_iio_channels;
+	indio_dev->num_channels = ARRAY_SIZE(imx8qxp_adc_iio_channels);
+
+	ret = devm_request_irq(dev, irq, imx8qxp_adc_isr, 0, dev_name(dev), adc);
+	if (ret < 0) {
+		dev_err(dev, "Failed requesting irq, irq = %d\n", irq);
+		return ret;
+	}
+
+	imx8qxp_adc_feature_prepare(adc);
+	imx8qxp_adc_reset(adc);
+
+	ret = iio_device_register(indio_dev);
+	if (ret) {
+		imx8qxp_adc_disable(adc);
+		dev_err(dev, "Couldn't register the device.\n");
+		return ret;
+	}
+
+	pm_runtime_set_active(dev);
+	pm_runtime_set_autosuspend_delay(dev, 50);
+	pm_runtime_use_autosuspend(dev);
+	pm_runtime_enable(dev);
+
 	return 0;
 }
 
 static int imx8qxp_adc_remove(struct platform_device *pdev)
 {
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+	struct device *dev = adc->dev;
+
+	pm_runtime_get_sync(dev);
+
+	iio_device_unregister(indio_dev);
+
+	imx8qxp_adc_disable(adc);
+
+	pm_runtime_disable(dev);
+	pm_runtime_put_noidle(dev);
+
 	return 0;
 }
 
 static int imx8qxp_adc_runtime_suspend(struct device *dev)
 {
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+
+	imx8qxp_adc_disable(adc);
+
+	clk_disable_unprepare(adc->clk);
+	clk_disable_unprepare(adc->ipg_clk);
+	regulator_disable(adc->vref);
+
 	return 0;
 }
 
 static int imx8qxp_adc_runtime_resume(struct device *dev)
 {
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+	int ret;
+
+	ret = regulator_enable(adc->vref);
+	if (ret) {
+		dev_err(dev, "Can't enable adc reference top voltage, err = %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(adc->clk);
+	if (ret) {
+		dev_err(dev, "Could not prepare or enable clock.\n");
+		regulator_disable(adc->vref);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(adc->ipg_clk);
+	if (ret) {
+		dev_err(dev, "Could not prepare or enable clock.\n");
+		clk_disable_unprepare(adc->clk);
+		regulator_disable(adc->vref);
+		return ret;
+	}
+	imx8qxp_adc_reset(adc);
+
 	return 0;
 }
 
-- 
2.25.1

[PATCH 3/6] iio: imx8qxp-adc: Add the detail for NXP i.MX8QuadXPlus ADC driver

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the detail for NXP
i.MX8QuadXPlus ADC driver which includes: probe/remove/pm_ops/iio_dev.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 drivers/iio/adc/imx8qxp-adc.c | 513 ++++++++++++++++++++++++++++++++++
 1 file changed, 513 insertions(+)

diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
index aec1b45c8fb9..d39bf382c582 100644
--- a/drivers/iio/adc/imx8qxp-adc.c
+++ b/drivers/iio/adc/imx8qxp-adc.c
@@ -20,23 +20,536 @@
 
 #define ADC_DRIVER_NAME		"imx8qxp-adc"
 
+/* Register map definition */
+#define ADC_CTRL		0x10
+#define ADC_STAT		0x14
+#define ADC_IE			0x18
+#define ADC_DE			0x1c
+#define ADC_CFG			0x20
+#define ADC_FCTRL		0x30
+#define ADC_SWTRIG		0x34
+#define ADC_TCTRL(tid)		(0xc0 + tid * 4)
+#define ADC_CMDH(cid)		(0x100 + cid * 8)
+#define ADC_CMDL(cid)		(0x104 + cid * 8)
+#define ADC_RESFIFO		0x300
+#define ADC_TST			0xffc
+
+/* ADC bit shift */
+#define ADC_IE_FWMIE_SHIFT		(0)
+#define ADC_CTRL_FIFO_RESET_SHIFT	(8)
+#define ADC_CTRL_SOFTWARE_RESET_SHIFT	(1)
+#define ADC_CTRL_ADC_ENABLE		(0)
+#define ADC_TCTRL_TCMD_SHIFT		(24)
+#define ADC_TCTRL_TDLY_SHIFT		(16)
+#define ADC_TCTRL_TPRI_SHIFT		(8)
+#define ADC_TCTRL_HTEN_SHIFT		(0)
+#define ADC_CMDL_CSCALE_SHIFT		(8)
+#define ADC_CMDL_MODE_SHIFT		(7)
+#define ADC_CMDL_DIFF_SHIFT		(6)
+#define ADC_CMDL_ABSEL_SHIFT		(5)
+#define ADC_CMDL_ADCH_SHIFT		(0)
+#define ADC_CMDH_NEXT_SHIFT		(24)
+#define ADC_CMDH_LOOP_SHIFT		(16)
+#define ADC_CMDH_AVGS_SHIFT		(12)
+#define ADC_CMDH_STS_SHIFT		(8)
+#define ADC_CMDH_LWI_SHIFT		(7)
+#define ADC_CMDH_CMPEN_SHIFT		(0)
+#define ADC_CFG_PWREN_SHIFT		(28)
+#define ADC_CFG_PUDLY_SHIFT		(16)
+#define ADC_CFG_REFSEL_SHIFT		(6)
+#define ADC_CFG_PWRSEL_SHIFT		(4)
+#define ADC_CFG_TPRICTRL_SHIFT		(0)
+#define ADC_FCTRL_FWMARK_SHIFT		(16)
+#define ADC_FCTRL_FWMARK_MASK		(0x1f << 16)
+#define ADC_FCTRL_FCOUNT_MASK		(0x1f)
+
+/* ADC PARAMETER*/
+#define ADC_CMDL_CHANNEL_SCALE_FULL		(0x3f)
+#define ADC_CMDL_SEL_A_A_B_CHANNEL		(0)
+#define ADC_CMDL_STANDARD_RESOLUTION		(0)
+#define ADC_CMDL_MODE_SINGLE			(0)
+#define ADC_CMDH_LWI_INCREMENT_DISABLE		(0)
+#define ADC_CMDH_CMPEN_DISABLE			(0)
+#define ADC_PAUSE_ENABLE			(0x80000000)
+#define ADC_TCTRL_TPRI_PRIORITY_HIGH		(0)
+
+#define ADC_TCTRL_HTEN_HARDWARE_TIRGGER_DISABLE	(0)
+
+#define MAX_CMD (8)
+#define MAX_TRIG (8)
+
+#define ADC_TIMEOUT		msecs_to_jiffies(100)
+
+struct imx8qxp_adc_trigger_ctrl {
+	u32 tcmd;
+	u32 tdly;
+	u32 tpri;
+	u32 hten;
+};
+
+struct imx8qxp_adc_cmd_l {
+	u32 scale;
+	u32 mode;
+	u32 diff;
+	u32 absel;
+	u32 adch;
+};
+
+struct imx8qxp_adc_cmd_h {
+	u32 next;
+	u32 loop;
+	u32 avgs;
+	u32 sts;
+	u32 lwi;
+	u32 cmpen;
+};
+
+struct imx8qxp_adc_cfg {
+	u32 pwren;
+	u32 pudly;
+	u32 refsel;
+	u32 pwrsel;
+	u32 tprictrl;
+};
+
+struct imx8qxp_adc {
+	struct device *dev;
+	void __iomem *regs;
+	struct clk *clk;
+	struct clk *ipg_clk;
+
+	u32 vref_uv;
+	u32 value;
+	u32 channel_id;
+	u32 trigger_id;
+	u32 cmd_id;
+
+	struct regulator *vref;
+	struct imx8qxp_adc_cmd_l adc_cmd_l[MAX_CMD + 1];
+	struct imx8qxp_adc_cmd_h adc_cmd_h[MAX_CMD + 1];
+	struct imx8qxp_adc_trigger_ctrl adc_trigger_ctrl[MAX_TRIG + 1];
+	struct imx8qxp_adc_cfg adc_cfg;
+	struct completion completion;
+};
+
+#define IMX8QXP_ADC_CHAN(_idx) {				\
+	.type = IIO_VOLTAGE,					\
+	.indexed = 1,						\
+	.channel = (_idx),					\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
+	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) |	\
+				BIT(IIO_CHAN_INFO_SAMP_FREQ),	\
+}
+
+static const struct iio_chan_spec imx8qxp_adc_iio_channels[] = {
+	IMX8QXP_ADC_CHAN(0),
+	IMX8QXP_ADC_CHAN(1),
+	IMX8QXP_ADC_CHAN(2),
+	IMX8QXP_ADC_CHAN(3),
+	IMX8QXP_ADC_CHAN(4),
+	IMX8QXP_ADC_CHAN(5),
+	IMX8QXP_ADC_CHAN(6),
+	IMX8QXP_ADC_CHAN(7),
+};
+
+static void imx8qxp_adc_feature_prepare(struct imx8qxp_adc *adc)
+{
+	u32 i;
+
+	adc->trigger_id = 0;
+	adc->cmd_id = 0;
+	adc->channel_id = 0;
+
+	for (i = 0; i < MAX_CMD + 1; i++) {
+		adc->adc_cmd_l[i].scale = 1;
+		adc->adc_cmd_l[i].mode = 0;
+		adc->adc_cmd_l[i].diff = 0;
+		adc->adc_cmd_l[i].absel = 0;
+		adc->adc_cmd_l[i].adch = 0;
+		adc->adc_cmd_h[i].next = 0;
+		adc->adc_cmd_h[i].loop = 0;
+		adc->adc_cmd_h[i].avgs = 0;
+		adc->adc_cmd_h[i].sts = 0;
+		adc->adc_cmd_h[i].lwi = 0;
+		adc->adc_cmd_h[i].cmpen = 0;
+	}
+
+	for (i = 0; i < MAX_TRIG; i++) {
+		adc->adc_trigger_ctrl[i].tcmd = 0;
+		adc->adc_trigger_ctrl[i].tdly = 0;
+		adc->adc_trigger_ctrl[i].tpri = 0;
+		adc->adc_trigger_ctrl[i].hten = 0;
+	}
+
+	adc->adc_cfg.pwren = 0;
+	adc->adc_cfg.pudly = 0;
+	adc->adc_cfg.refsel = 0;
+	adc->adc_cfg.pwrsel = 0;
+	adc->adc_cfg.tprictrl = 0;
+}
+
+static void imx8qxp_adc_reset(struct imx8qxp_adc *adc)
+{
+	u32 ctrl;
+
+	/*software reset, need to clear the set bit*/
+	ctrl = readl(adc->regs + ADC_CTRL);
+	ctrl |= 1 << ADC_CTRL_SOFTWARE_RESET_SHIFT;
+	writel(ctrl, adc->regs + ADC_CTRL);
+	udelay(10);
+	ctrl &= ~(1 << ADC_CTRL_SOFTWARE_RESET_SHIFT);
+	writel(ctrl, adc->regs + ADC_CTRL);
+
+	/* reset the fifo */
+	ctrl |= 1 << ADC_CTRL_FIFO_RESET_SHIFT;
+	writel(ctrl, adc->regs + ADC_CTRL);
+}
+
+static void imx8qxp_adc_reg_config(struct imx8qxp_adc *adc)
+{
+	u32 adc_cfg, adc_tctrl, adc_cmdl, adc_cmdh;
+	u32 t_id, c_id;
+
+	adc_cfg = adc->adc_cfg.pwren << ADC_CFG_PWREN_SHIFT |
+		  adc->adc_cfg.pudly << ADC_CFG_PUDLY_SHIFT |
+		  adc->adc_cfg.refsel << ADC_CFG_REFSEL_SHIFT |
+		  adc->adc_cfg.pwrsel << ADC_CFG_PWRSEL_SHIFT |
+		  adc->adc_cfg.tprictrl << ADC_CFG_TPRICTRL_SHIFT;
+	writel(adc_cfg, adc->regs + ADC_CFG);
+
+	t_id = adc->trigger_id;
+	adc_tctrl = adc->adc_trigger_ctrl[t_id].tcmd << ADC_TCTRL_TCMD_SHIFT |
+		    adc->adc_trigger_ctrl[t_id].tdly << ADC_TCTRL_TDLY_SHIFT |
+		    adc->adc_trigger_ctrl[t_id].tpri << ADC_TCTRL_TPRI_SHIFT |
+		    adc->adc_trigger_ctrl[t_id].hten << ADC_TCTRL_HTEN_SHIFT;
+	writel(adc_tctrl, adc->regs + ADC_TCTRL(t_id));
+
+	c_id = adc->cmd_id - 1;
+	adc_cmdl = adc->adc_cmd_l[c_id].scale << ADC_CMDL_CSCALE_SHIFT |
+		   adc->adc_cmd_l[c_id].mode << ADC_CMDL_MODE_SHIFT |
+		   adc->adc_cmd_l[c_id].diff << ADC_CMDL_DIFF_SHIFT |
+		   adc->adc_cmd_l[c_id].absel << ADC_CMDL_ABSEL_SHIFT |
+		   adc->adc_cmd_l[c_id].adch << ADC_CMDL_ADCH_SHIFT;
+	writel(adc_cmdl, adc->regs + ADC_CMDL(c_id));
+
+	adc_cmdh = adc->adc_cmd_h[c_id].next << ADC_CMDH_NEXT_SHIFT |
+		   adc->adc_cmd_h[c_id].loop << ADC_CMDH_LOOP_SHIFT |
+		   adc->adc_cmd_h[c_id].avgs << ADC_CMDH_AVGS_SHIFT |
+		   adc->adc_cmd_h[c_id].sts << ADC_CMDH_STS_SHIFT |
+		   adc->adc_cmd_h[c_id].lwi << ADC_CMDH_LWI_SHIFT |
+		   adc->adc_cmd_h[c_id].cmpen << ADC_CMDH_CMPEN_SHIFT;
+	writel(adc_cmdh, adc->regs + ADC_CMDH(c_id));
+}
+
+static void imx8qxp_adc_mode_config(struct imx8qxp_adc *adc)
+{
+	u32 cmd_id, trigger_id, channel_id;
+
+	channel_id = adc->channel_id;
+	cmd_id = adc->cmd_id - 1;
+	trigger_id = adc->trigger_id;
+
+	/* config the cmd */
+	adc->adc_cmd_l[cmd_id].scale = ADC_CMDL_CHANNEL_SCALE_FULL;
+	adc->adc_cmd_l[cmd_id].mode = ADC_CMDL_STANDARD_RESOLUTION;
+	adc->adc_cmd_l[cmd_id].diff = ADC_CMDL_MODE_SINGLE;
+	adc->adc_cmd_l[cmd_id].absel = ADC_CMDL_SEL_A_A_B_CHANNEL;
+	adc->adc_cmd_l[cmd_id].adch = channel_id;
+
+	adc->adc_cmd_h[cmd_id].next = 0;
+	adc->adc_cmd_h[cmd_id].loop = 0;
+	adc->adc_cmd_h[cmd_id].avgs = 7;
+	adc->adc_cmd_h[cmd_id].sts = 0;
+	adc->adc_cmd_h[cmd_id].lwi = ADC_CMDH_LWI_INCREMENT_DISABLE;
+	adc->adc_cmd_h[cmd_id].cmpen = ADC_CMDH_CMPEN_DISABLE;
+
+	/* config the trigger control */
+	adc->adc_trigger_ctrl[trigger_id].tcmd = adc->cmd_id;
+	adc->adc_trigger_ctrl[trigger_id].tdly = 0;
+	adc->adc_trigger_ctrl[trigger_id].tpri = ADC_TCTRL_TPRI_PRIORITY_HIGH;
+	adc->adc_trigger_ctrl[trigger_id].hten = ADC_TCTRL_HTEN_HARDWARE_TIRGGER_DISABLE;
+
+	/* ADC configuration */
+	adc->adc_cfg.pwren = 1;
+	adc->adc_cfg.pudly = 0x80;
+	adc->adc_cfg.refsel = 0;
+	adc->adc_cfg.pwrsel = 3;
+	adc->adc_cfg.tprictrl = 0;
+
+	imx8qxp_adc_reg_config(adc);
+}
+
+static void imx8qxp_adc_fifo_config(struct imx8qxp_adc *adc)
+{
+	u32 fifo_ctrl, interrupt_en;
+
+	fifo_ctrl = readl(adc->regs + ADC_FCTRL);
+	fifo_ctrl &= ~ADC_FCTRL_FWMARK_MASK;
+	/* set the watermark level to 1 */
+	fifo_ctrl |= 0 << ADC_FCTRL_FWMARK_SHIFT;
+	writel(fifo_ctrl, adc->regs + ADC_FCTRL);
+
+	/* FIFO Watermark Interrupt Enable */
+	interrupt_en = readl(adc->regs + ADC_IE);
+	interrupt_en |= 1 << ADC_IE_FWMIE_SHIFT;
+	writel(interrupt_en, adc->regs + ADC_IE);
+}
+
+static void imx8qxp_adc_disable(struct imx8qxp_adc *adc)
+{
+	u32 ctrl;
+
+	ctrl = readl(adc->regs + ADC_CTRL) & ~(1 << ADC_CTRL_ADC_ENABLE);
+	writel(ctrl, adc->regs + ADC_CTRL);
+}
+
+static int imx8qxp_adc_read_raw(struct iio_dev *indio_dev, struct iio_chan_spec const *chan,
+				int *val, int *val2, long mask)
+{
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+	struct device *dev = adc->dev;
+
+	u32 channel;
+	u32 ctrl;
+	long ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		pm_runtime_get_sync(dev);
+
+		mutex_lock(&indio_dev->mlock);
+		reinit_completion(&adc->completion);
+
+		channel = chan->channel & 0x07;
+		adc->channel_id = channel;
+		adc->cmd_id = 1;
+		adc->trigger_id = 0;
+		imx8qxp_adc_mode_config(adc);
+
+		imx8qxp_adc_fifo_config(adc);
+
+		/* adc enable */
+		ctrl = readl(adc->regs + ADC_CTRL) | (1 << ADC_CTRL_ADC_ENABLE);
+		writel(ctrl, adc->regs + ADC_CTRL);
+		/* adc start */
+		writel(1 << adc->trigger_id, adc->regs + ADC_SWTRIG);
+
+		ret = wait_for_completion_interruptible_timeout
+				(&adc->completion, ADC_TIMEOUT);
+
+		pm_runtime_mark_last_busy(dev);
+		pm_runtime_put_sync_autosuspend(dev);
+
+		if (ret == 0) {
+			mutex_unlock(&indio_dev->mlock);
+			return -ETIMEDOUT;
+		}
+		if (ret < 0) {
+			mutex_unlock(&indio_dev->mlock);
+			return ret;
+		}
+
+		*val = adc->value;
+		mutex_unlock(&indio_dev->mlock);
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_SCALE:
+		adc->vref_uv = regulator_get_voltage(adc->vref);
+		*val = adc->vref_uv / 1000;
+		*val2 = 12;
+		return IIO_VAL_FRACTIONAL_LOG2;
+
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*val = clk_get_rate(adc->clk) / 3;
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
+static irqreturn_t imx8qxp_adc_isr(int irq, void *dev_id)
+{
+	struct imx8qxp_adc *adc = (struct imx8qxp_adc *)dev_id;
+
+	u32 fifo_count;
+
+	fifo_count = readl(adc->regs + ADC_FCTRL)
+			& ADC_FCTRL_FCOUNT_MASK;
+
+	if (fifo_count) {
+		adc->value = (readl(adc->regs + ADC_RESFIFO) & 0xffff) >> 3;
+		complete(&adc->completion);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int imx8qxp_adc_reg_access(struct iio_dev *indio_dev, unsigned int reg,
+				  unsigned int writeval, unsigned int *readval)
+{
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+	struct device *dev = adc->dev;
+
+	if (!readval || reg % 4 || reg > ADC_TST)
+		return -EINVAL;
+
+	pm_runtime_get_sync(dev);
+
+	*readval = readl(adc->regs + reg);
+
+	pm_runtime_mark_last_busy(dev);
+	pm_runtime_put_sync_autosuspend(dev);
+
+	return 0;
+}
+
+static const struct iio_info imx8qxp_adc_iio_info = {
+	.read_raw = &imx8qxp_adc_read_raw,
+	.debugfs_reg_access = &imx8qxp_adc_reg_access,
+};
+
 static int imx8qxp_adc_probe(struct platform_device *pdev)
 {
+	struct imx8qxp_adc *adc;
+	struct iio_dev *indio_dev;
+	struct device *dev = &pdev->dev;
+	int irq;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
+	if (!indio_dev) {
+		dev_err(dev, "Failed allocating iio device\n");
+		return -ENOMEM;
+	}
+
+	adc = iio_priv(indio_dev);
+	adc->dev = dev;
+
+	adc->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(adc->regs))
+		return PTR_ERR(adc->regs);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	adc->clk = devm_clk_get(dev, "per");
+	if (IS_ERR(adc->clk)) {
+		ret = PTR_ERR(adc->clk);
+		dev_err(dev, "Failed getting clock, err = %d\n", ret);
+		return ret;
+	}
+
+	adc->ipg_clk = devm_clk_get(dev, "ipg");
+	if (IS_ERR(adc->ipg_clk)) {
+		ret = PTR_ERR(adc->ipg_clk);
+		dev_err(dev, "Failed getting clock, err = %d\n", ret);
+		return ret;
+	}
+
+	adc->vref = devm_regulator_get(dev, "vref");
+	if (IS_ERR(adc->vref)) {
+		ret = PTR_ERR(adc->vref);
+		dev_err(dev,
+			"Failed getting reference voltage, err = %d\n", ret);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, indio_dev);
+
+	init_completion(&adc->completion);
+
+	indio_dev->name = dev_name(dev);
+	indio_dev->info = &imx8qxp_adc_iio_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = imx8qxp_adc_iio_channels;
+	indio_dev->num_channels = ARRAY_SIZE(imx8qxp_adc_iio_channels);
+
+	ret = devm_request_irq(dev, irq, imx8qxp_adc_isr, 0, dev_name(dev), adc);
+	if (ret < 0) {
+		dev_err(dev, "Failed requesting irq, irq = %d\n", irq);
+		return ret;
+	}
+
+	imx8qxp_adc_feature_prepare(adc);
+	imx8qxp_adc_reset(adc);
+
+	ret = iio_device_register(indio_dev);
+	if (ret) {
+		imx8qxp_adc_disable(adc);
+		dev_err(dev, "Couldn't register the device.\n");
+		return ret;
+	}
+
+	pm_runtime_set_active(dev);
+	pm_runtime_set_autosuspend_delay(dev, 50);
+	pm_runtime_use_autosuspend(dev);
+	pm_runtime_enable(dev);
+
 	return 0;
 }
 
 static int imx8qxp_adc_remove(struct platform_device *pdev)
 {
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+	struct device *dev = adc->dev;
+
+	pm_runtime_get_sync(dev);
+
+	iio_device_unregister(indio_dev);
+
+	imx8qxp_adc_disable(adc);
+
+	pm_runtime_disable(dev);
+	pm_runtime_put_noidle(dev);
+
 	return 0;
 }
 
 static int imx8qxp_adc_runtime_suspend(struct device *dev)
 {
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+
+	imx8qxp_adc_disable(adc);
+
+	clk_disable_unprepare(adc->clk);
+	clk_disable_unprepare(adc->ipg_clk);
+	regulator_disable(adc->vref);
+
 	return 0;
 }
 
 static int imx8qxp_adc_runtime_resume(struct device *dev)
 {
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct imx8qxp_adc *adc = iio_priv(indio_dev);
+	int ret;
+
+	ret = regulator_enable(adc->vref);
+	if (ret) {
+		dev_err(dev, "Can't enable adc reference top voltage, err = %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(adc->clk);
+	if (ret) {
+		dev_err(dev, "Could not prepare or enable clock.\n");
+		regulator_disable(adc->vref);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(adc->ipg_clk);
+	if (ret) {
+		dev_err(dev, "Could not prepare or enable clock.\n");
+		clk_disable_unprepare(adc->clk);
+		regulator_disable(adc->vref);
+		return ret;
+	}
+	imx8qxp_adc_reset(adc);
+
 	return 0;
 }
 
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/6] iio: imx8qxp-adc: Add the detail for NXP i.MX8QuadXPlus ADC driver

[Jonathan Cameron]

On Tue, 31 Aug 2021 01:21:37 +0800
Cai Huoqing <caihuoqing@baidu.com> wrote:

> The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the detail for NXP
> i.MX8QuadXPlus ADC driver which includes: probe/remove/pm_ops/iio_dev.
> 
> Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
> ---
>  drivers/iio/adc/imx8qxp-adc.c | 513 ++++++++++++++++++++++++++++++++++
>  1 file changed, 513 insertions(+)
> 
> diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
> index aec1b45c8fb9..d39bf382c582 100644
> --- a/drivers/iio/adc/imx8qxp-adc.c
> +++ b/drivers/iio/adc/imx8qxp-adc.c
> @@ -20,23 +20,536 @@
>  
>  #define ADC_DRIVER_NAME		"imx8qxp-adc"
>  
> +/* Register map definition */
> +#define ADC_CTRL		0x10
Give a device specific prefix.  The chances of these shadowing naming in
some future ore header is rather high so let us prevent that now.
IMX8QXP_ADC_STAT  etc.

Naming wise it is usually good to clearly distinguish registers from field
names.  There are lots of ways to do this, but a postfix of _REG or _ADR
works well.

> +#define ADC_STAT		0x14
> +#define ADC_IE			0x18
> +#define ADC_DE			0x1c
> +#define ADC_CFG			0x20
> +#define ADC_FCTRL		0x30
> +#define ADC_SWTRIG		0x34
> +#define ADC_TCTRL(tid)		(0xc0 + tid * 4)
> +#define ADC_CMDH(cid)		(0x100 + cid * 8)
> +#define ADC_CMDL(cid)		(0x104 + cid * 8)
> +#define ADC_RESFIFO		0x300
> +#define ADC_TST			0xffc
> +
> +/* ADC bit shift */
> +#define ADC_IE_FWMIE_SHIFT		(0)

All the brackets around individual numbers are unnecessary.

Cleaner and more consistent way to define register fields is
to use masks only (BIT or GENMASK as appropriate) and then use
PREP_FIELD() and GET_FIELD() to manipulate the actual values.

> +#define ADC_CTRL_FIFO_RESET_SHIFT	(8)
> +#define ADC_CTRL_SOFTWARE_RESET_SHIFT	(1)
> +#define ADC_CTRL_ADC_ENABLE		(0)
> +#define ADC_TCTRL_TCMD_SHIFT		(24)
> +#define ADC_TCTRL_TDLY_SHIFT		(16)
> +#define ADC_TCTRL_TPRI_SHIFT		(8)
> +#define ADC_TCTRL_HTEN_SHIFT		(0)
> +#define ADC_CMDL_CSCALE_SHIFT		(8)
> +#define ADC_CMDL_MODE_SHIFT		(7)
> +#define ADC_CMDL_DIFF_SHIFT		(6)
> +#define ADC_CMDL_ABSEL_SHIFT		(5)
> +#define ADC_CMDL_ADCH_SHIFT		(0)
> +#define ADC_CMDH_NEXT_SHIFT		(24)
> +#define ADC_CMDH_LOOP_SHIFT		(16)
> +#define ADC_CMDH_AVGS_SHIFT		(12)
> +#define ADC_CMDH_STS_SHIFT		(8)
> +#define ADC_CMDH_LWI_SHIFT		(7)
> +#define ADC_CMDH_CMPEN_SHIFT		(0)
> +#define ADC_CFG_PWREN_SHIFT		(28)
> +#define ADC_CFG_PUDLY_SHIFT		(16)
> +#define ADC_CFG_REFSEL_SHIFT		(6)
> +#define ADC_CFG_PWRSEL_SHIFT		(4)
> +#define ADC_CFG_TPRICTRL_SHIFT		(0)
> +#define ADC_FCTRL_FWMARK_SHIFT		(16)
> +#define ADC_FCTRL_FWMARK_MASK		(0x1f << 16)
> +#define ADC_FCTRL_FCOUNT_MASK		(0x1f)
> +
> +/* ADC PARAMETER*/
> +#define ADC_CMDL_CHANNEL_SCALE_FULL		(0x3f)
> +#define ADC_CMDL_SEL_A_A_B_CHANNEL		(0)
> +#define ADC_CMDL_STANDARD_RESOLUTION		(0)
> +#define ADC_CMDL_MODE_SINGLE			(0)
> +#define ADC_CMDH_LWI_INCREMENT_DISABLE		(0)
> +#define ADC_CMDH_CMPEN_DISABLE			(0)
> +#define ADC_PAUSE_ENABLE			(0x80000000)
> +#define ADC_TCTRL_TPRI_PRIORITY_HIGH		(0)
> +
> +#define ADC_TCTRL_HTEN_HARDWARE_TIRGGER_DISABLE	(0)
> +
> +#define MAX_CMD (8)
> +#define MAX_TRIG (8)
> +
> +#define ADC_TIMEOUT		msecs_to_jiffies(100)
> +
> +struct imx8qxp_adc_trigger_ctrl {
> +	u32 tcmd;

I'll guess from the shifts above that these are larger than they
would be if reflecting actual possible values. Please use u8 etc
as appropriate.  Or just store these as caches of the registers and use
GET_FIELD and PREP_FIELD to manipulate them.

Mind you, so far I don't know what they are for ;)

> +	u32 tdly;
> +	u32 tpri;
> +	u32 hten;
> +};
> +
> +struct imx8qxp_adc_cmd_l {
> +	u32 scale;
> +	u32 mode;
> +	u32 diff;
> +	u32 absel;
> +	u32 adch;
> +};
> +
> +struct imx8qxp_adc_cmd_h {
> +	u32 next;
> +	u32 loop;
> +	u32 avgs;
> +	u32 sts;
> +	u32 lwi;
> +	u32 cmpen;
> +};
> +
> +struct imx8qxp_adc_cfg {
> +	u32 pwren;
> +	u32 pudly;
> +	u32 refsel;
> +	u32 pwrsel;
> +	u32 tprictrl;
> +};
> +
> +struct imx8qxp_adc {
> +	struct device *dev;
> +	void __iomem *regs;
> +	struct clk *clk;
> +	struct clk *ipg_clk;
> +
> +	u32 vref_uv;
> +	u32 value;
> +	u32 channel_id;
> +	u32 trigger_id;
As mentioned below, a lot of this doesn't seem to be necessary to cache in here.
If we can keep it local in the driver, that would be better.
> +	u32 cmd_id;
> +
> +	struct regulator *vref;
> +	struct imx8qxp_adc_cmd_l adc_cmd_l[MAX_CMD + 1];
> +	struct imx8qxp_adc_cmd_h adc_cmd_h[MAX_CMD + 1];
> +	struct imx8qxp_adc_trigger_ctrl adc_trigger_ctrl[MAX_TRIG + 1];
> +	struct imx8qxp_adc_cfg adc_cfg;
> +	struct completion completion;
> +};
> +
> +#define IMX8QXP_ADC_CHAN(_idx) {				\
> +	.type = IIO_VOLTAGE,					\
> +	.indexed = 1,						\
> +	.channel = (_idx),					\
> +	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
> +	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) |	\
> +				BIT(IIO_CHAN_INFO_SAMP_FREQ),	\
> +}
> +
> +static const struct iio_chan_spec imx8qxp_adc_iio_channels[] = {
> +	IMX8QXP_ADC_CHAN(0),
> +	IMX8QXP_ADC_CHAN(1),
> +	IMX8QXP_ADC_CHAN(2),
> +	IMX8QXP_ADC_CHAN(3),
> +	IMX8QXP_ADC_CHAN(4),
> +	IMX8QXP_ADC_CHAN(5),
> +	IMX8QXP_ADC_CHAN(6),
> +	IMX8QXP_ADC_CHAN(7),
> +};
> +
> +static void imx8qxp_adc_feature_prepare(struct imx8qxp_adc *adc)
> +{
> +	u32 i;
> +
> +	adc->trigger_id = 0;
> +	adc->cmd_id = 0;
> +	adc->channel_id = 0;
> +
> +	for (i = 0; i < MAX_CMD + 1; i++) {
> +		adc->adc_cmd_l[i].scale = 1;
> +		adc->adc_cmd_l[i].mode = 0;
> +		adc->adc_cmd_l[i].diff = 0;
> +		adc->adc_cmd_l[i].absel = 0;
> +		adc->adc_cmd_l[i].adch = 0;
> +		adc->adc_cmd_h[i].next = 0;
> +		adc->adc_cmd_h[i].loop = 0;
> +		adc->adc_cmd_h[i].avgs = 0;
> +		adc->adc_cmd_h[i].sts = 0;
> +		adc->adc_cmd_h[i].lwi = 0;
> +		adc->adc_cmd_h[i].cmpen = 0;
> +	}
> +
> +	for (i = 0; i < MAX_TRIG; i++) {
> +		adc->adc_trigger_ctrl[i].tcmd = 0;
> +		adc->adc_trigger_ctrl[i].tdly = 0;
> +		adc->adc_trigger_ctrl[i].tpri = 0;
> +		adc->adc_trigger_ctrl[i].hten = 0;
> +	}
> +
> +	adc->adc_cfg.pwren = 0;
> +	adc->adc_cfg.pudly = 0;
> +	adc->adc_cfg.refsel = 0;
> +	adc->adc_cfg.pwrsel = 0;
> +	adc->adc_cfg.tprictrl = 0;
> +}
> +
> +static void imx8qxp_adc_reset(struct imx8qxp_adc *adc)
> +{
> +	u32 ctrl;
> +
> +	/*software reset, need to clear the set bit*/
> +	ctrl = readl(adc->regs + ADC_CTRL);
> +	ctrl |= 1 << ADC_CTRL_SOFTWARE_RESET_SHIFT;
> +	writel(ctrl, adc->regs + ADC_CTRL);
> +	udelay(10);
> +	ctrl &= ~(1 << ADC_CTRL_SOFTWARE_RESET_SHIFT);
> +	writel(ctrl, adc->regs + ADC_CTRL);
> +
> +	/* reset the fifo */
> +	ctrl |= 1 << ADC_CTRL_FIFO_RESET_SHIFT;
> +	writel(ctrl, adc->regs + ADC_CTRL);
> +}
> +
> +static void imx8qxp_adc_reg_config(struct imx8qxp_adc *adc)
> +{
> +	u32 adc_cfg, adc_tctrl, adc_cmdl, adc_cmdh;
> +	u32 t_id, c_id;
> +
> +	adc_cfg = adc->adc_cfg.pwren << ADC_CFG_PWREN_SHIFT |
> +		  adc->adc_cfg.pudly << ADC_CFG_PUDLY_SHIFT |
> +		  adc->adc_cfg.refsel << ADC_CFG_REFSEL_SHIFT |
> +		  adc->adc_cfg.pwrsel << ADC_CFG_PWRSEL_SHIFT |
> +		  adc->adc_cfg.tprictrl << ADC_CFG_TPRICTRL_SHIFT;

Lots of FIELD_PREP(), or as I mention above perhaps just put these
directly in place at the point of setting the values in adc->xxx
rather than leaving it to where you write them.
 
> +	writel(adc_cfg, adc->regs + ADC_CFG);
> +
> +	t_id = adc->trigger_id;
> +	adc_tctrl = adc->adc_trigger_ctrl[t_id].tcmd << ADC_TCTRL_TCMD_SHIFT |
> +		    adc->adc_trigger_ctrl[t_id].tdly << ADC_TCTRL_TDLY_SHIFT |
> +		    adc->adc_trigger_ctrl[t_id].tpri << ADC_TCTRL_TPRI_SHIFT |
> +		    adc->adc_trigger_ctrl[t_id].hten << ADC_TCTRL_HTEN_SHIFT;
> +	writel(adc_tctrl, adc->regs + ADC_TCTRL(t_id));
> +
> +	c_id = adc->cmd_id - 1;
> +	adc_cmdl = adc->adc_cmd_l[c_id].scale << ADC_CMDL_CSCALE_SHIFT |
> +		   adc->adc_cmd_l[c_id].mode << ADC_CMDL_MODE_SHIFT |
> +		   adc->adc_cmd_l[c_id].diff << ADC_CMDL_DIFF_SHIFT |
> +		   adc->adc_cmd_l[c_id].absel << ADC_CMDL_ABSEL_SHIFT |
> +		   adc->adc_cmd_l[c_id].adch << ADC_CMDL_ADCH_SHIFT;
> +	writel(adc_cmdl, adc->regs + ADC_CMDL(c_id));
> +
> +	adc_cmdh = adc->adc_cmd_h[c_id].next << ADC_CMDH_NEXT_SHIFT |
> +		   adc->adc_cmd_h[c_id].loop << ADC_CMDH_LOOP_SHIFT |
> +		   adc->adc_cmd_h[c_id].avgs << ADC_CMDH_AVGS_SHIFT |
> +		   adc->adc_cmd_h[c_id].sts << ADC_CMDH_STS_SHIFT |
> +		   adc->adc_cmd_h[c_id].lwi << ADC_CMDH_LWI_SHIFT |
> +		   adc->adc_cmd_h[c_id].cmpen << ADC_CMDH_CMPEN_SHIFT;
> +	writel(adc_cmdh, adc->regs + ADC_CMDH(c_id));
> +}
> +
> +static void imx8qxp_adc_mode_config(struct imx8qxp_adc *adc)
> +{
> +	u32 cmd_id, trigger_id, channel_id;
> +
> +	channel_id = adc->channel_id;
> +	cmd_id = adc->cmd_id - 1;

Call the local variable something different as it's clearly not
what would be thought of as cmd_id elsewhere in the driver.

> +	trigger_id = adc->trigger_id;
> +
> +	/* config the cmd */
> +	adc->adc_cmd_l[cmd_id].scale = ADC_CMDL_CHANNEL_SCALE_FULL;
> +	adc->adc_cmd_l[cmd_id].mode = ADC_CMDL_STANDARD_RESOLUTION;
> +	adc->adc_cmd_l[cmd_id].diff = ADC_CMDL_MODE_SINGLE;
> +	adc->adc_cmd_l[cmd_id].absel = ADC_CMDL_SEL_A_A_B_CHANNEL;
> +	adc->adc_cmd_l[cmd_id].adch = channel_id;
> +
> +	adc->adc_cmd_h[cmd_id].next = 0;
> +	adc->adc_cmd_h[cmd_id].loop = 0;
> +	adc->adc_cmd_h[cmd_id].avgs = 7;
> +	adc->adc_cmd_h[cmd_id].sts = 0;
> +	adc->adc_cmd_h[cmd_id].lwi = ADC_CMDH_LWI_INCREMENT_DISABLE;
> +	adc->adc_cmd_h[cmd_id].cmpen = ADC_CMDH_CMPEN_DISABLE;
> +
> +	/* config the trigger control */
> +	adc->adc_trigger_ctrl[trigger_id].tcmd = adc->cmd_id;
> +	adc->adc_trigger_ctrl[trigger_id].tdly = 0;
> +	adc->adc_trigger_ctrl[trigger_id].tpri = ADC_TCTRL_TPRI_PRIORITY_HIGH;
> +	adc->adc_trigger_ctrl[trigger_id].hten = ADC_TCTRL_HTEN_HARDWARE_TIRGGER_DISABLE;
> +
> +	/* ADC configuration */
> +	adc->adc_cfg.pwren = 1;
> +	adc->adc_cfg.pudly = 0x80;
> +	adc->adc_cfg.refsel = 0;
> +	adc->adc_cfg.pwrsel = 3;
> +	adc->adc_cfg.tprictrl = 0;
> +
> +	imx8qxp_adc_reg_config(adc);
> +}
> +
> +static void imx8qxp_adc_fifo_config(struct imx8qxp_adc *adc)
> +{
> +	u32 fifo_ctrl, interrupt_en;
> +
> +	fifo_ctrl = readl(adc->regs + ADC_FCTRL);
> +	fifo_ctrl &= ~ADC_FCTRL_FWMARK_MASK;
> +	/* set the watermark level to 1 */
> +	fifo_ctrl |= 0 << ADC_FCTRL_FWMARK_SHIFT;
FIELD_PREP()

> +	writel(fifo_ctrl, adc->regs + ADC_FCTRL);
> +
> +	/* FIFO Watermark Interrupt Enable */
> +	interrupt_en = readl(adc->regs + ADC_IE);
> +	interrupt_en |= 1 << ADC_IE_FWMIE_SHIFT;
FIELD_PREP()

> +	writel(interrupt_en, adc->regs + ADC_IE);
> +}
> +
> +static void imx8qxp_adc_disable(struct imx8qxp_adc *adc)
> +{
> +	u32 ctrl;
> +
> +	ctrl = readl(adc->regs + ADC_CTRL) & ~(1 << ADC_CTRL_ADC_ENABLE);

~BIT(ADC_CTRL_ADC_ENABLE) or appropriate FIELD_PREP

> +	writel(ctrl, adc->regs + ADC_CTRL);
> +}
> +
> +static int imx8qxp_adc_read_raw(struct iio_dev *indio_dev, struct iio_chan_spec const *chan,
> +				int *val, int *val2, long mask)
> +{
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +	struct device *dev = adc->dev;
> +
> +	u32 channel;
> +	u32 ctrl;
> +	long ret;
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_RAW:
> +		pm_runtime_get_sync(dev);
> +
> +		mutex_lock(&indio_dev->mlock);
Please do not use mlock directly.  If you are protecting driver local data
(so stuff in iio_priv()) or hardware resources define your own local lock
in iio_priv() with well documented scope.

If the aim is to prevent racing with IIO core state changes, then use
iio_device_claim_direct().  That only applies if the driver supports buffered
mode as otherwise you won't get state changes.

> +		reinit_completion(&adc->completion);
> +
> +		channel = chan->channel & 0x07;
> +		adc->channel_id = channel;
> +		adc->cmd_id = 1;
> +		adc->trigger_id = 0;
> +		imx8qxp_adc_mode_config(adc);

Why not pass channel, cmd_id and trigger_id into this function rather than using
state in iio_priv() for them?  I checked adc->channel_id and it is only used
in that function so you should not have it in the iio_priv() structure at all.
For the others I haven't checked but would guess similar?

> +
> +		imx8qxp_adc_fifo_config(adc);
> +
> +		/* adc enable */
> +		ctrl = readl(adc->regs + ADC_CTRL) | (1 << ADC_CTRL_ADC_ENABLE);
> +		writel(ctrl, adc->regs + ADC_CTRL);
> +		/* adc start */
> +		writel(1 << adc->trigger_id, adc->regs + ADC_SWTRIG);
> +
> +		ret = wait_for_completion_interruptible_timeout
> +				(&adc->completion, ADC_TIMEOUT);

Readabilty of this line is hurt by it being broken up so as long as it is under 100 chars
I'd prefer it one line.

> +
> +		pm_runtime_mark_last_busy(dev);
> +		pm_runtime_put_sync_autosuspend(dev);
> +
> +		if (ret == 0) {
> +			mutex_unlock(&indio_dev->mlock);
> +			return -ETIMEDOUT;
> +		}
> +		if (ret < 0) {
> +			mutex_unlock(&indio_dev->mlock);
> +			return ret;
> +		}
> +
> +		*val = adc->value;
As mentioned below, why not do the register read here rather than caching it before
calling complete()?

> +		mutex_unlock(&indio_dev->mlock);
> +		return IIO_VAL_INT;
> +
> +	case IIO_CHAN_INFO_SCALE:
> +		adc->vref_uv = regulator_get_voltage(adc->vref);
Why cache it? Use a local variable.

> +		*val = adc->vref_uv / 1000;
> +		*val2 = 12;
> +		return IIO_VAL_FRACTIONAL_LOG2;
> +
> +	case IIO_CHAN_INFO_SAMP_FREQ:
> +		*val = clk_get_rate(adc->clk) / 3;
> +		return IIO_VAL_INT;
> +
> +	default:
> +		return -EINVAL;
> +	}
> +}
> +
> +static irqreturn_t imx8qxp_adc_isr(int irq, void *dev_id)
> +{
> +	struct imx8qxp_adc *adc = (struct imx8qxp_adc *)dev_id;
> +
> +	u32 fifo_count;
> +
> +	fifo_count = readl(adc->regs + ADC_FCTRL)
> +			& ADC_FCTRL_FCOUNT_MASK;

One line as still well under 80 chars.  As mentioned above, FIELD_GET()
preferred as means the reviewer / reader doesn't need to go check this
mask is from bit 0 upwards.

> +
> +	if (fifo_count) {
> +		adc->value = (readl(adc->regs + ADC_RESFIFO) & 0xffff) >> 3;
> +		complete(&adc->completion);

Why do the adc->value read here rather than in the completion?
If there is a potential race I'd expect it to also affect adc->value


> +	}
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int imx8qxp_adc_reg_access(struct iio_dev *indio_dev, unsigned int reg,
> +				  unsigned int writeval, unsigned int *readval)
> +{
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +	struct device *dev = adc->dev;
> +
> +	if (!readval || reg % 4 || reg > ADC_TST)
> +		return -EINVAL;
> +
> +	pm_runtime_get_sync(dev);
> +
> +	*readval = readl(adc->regs + reg);
> +
> +	pm_runtime_mark_last_busy(dev);
> +	pm_runtime_put_sync_autosuspend(dev);
> +
> +	return 0;
> +}
> +
> +static const struct iio_info imx8qxp_adc_iio_info = {
> +	.read_raw = &imx8qxp_adc_read_raw,
> +	.debugfs_reg_access = &imx8qxp_adc_reg_access,
> +};
> +
>  static int imx8qxp_adc_probe(struct platform_device *pdev)
>  {
> +	struct imx8qxp_adc *adc;
> +	struct iio_dev *indio_dev;
> +	struct device *dev = &pdev->dev;
> +	int irq;
> +	int ret;
> +
> +	indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
> +	if (!indio_dev) {
> +		dev_err(dev, "Failed allocating iio device\n");
> +		return -ENOMEM;
> +	}
> +
> +	adc = iio_priv(indio_dev);
> +	adc->dev = dev;
> +
> +	adc->regs = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(adc->regs))
> +		return PTR_ERR(adc->regs);
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0)
> +		return irq;
> +
> +	adc->clk = devm_clk_get(dev, "per");
> +	if (IS_ERR(adc->clk)) {
> +		ret = PTR_ERR(adc->clk);
> +		dev_err(dev, "Failed getting clock, err = %d\n", ret);
> +		return ret;
> +	}
> +
> +	adc->ipg_clk = devm_clk_get(dev, "ipg");
> +	if (IS_ERR(adc->ipg_clk)) {
> +		ret = PTR_ERR(adc->ipg_clk);
> +		dev_err(dev, "Failed getting clock, err = %d\n", ret);
> +		return ret;
> +	}
> +
> +	adc->vref = devm_regulator_get(dev, "vref");
> +	if (IS_ERR(adc->vref)) {
> +		ret = PTR_ERR(adc->vref);
> +		dev_err(dev,
> +			"Failed getting reference voltage, err = %d\n", ret);
> +		return ret;
> +	}
> +
> +	platform_set_drvdata(pdev, indio_dev);
> +
> +	init_completion(&adc->completion);
> +
> +	indio_dev->name = dev_name(dev);
> +	indio_dev->info = &imx8qxp_adc_iio_info;
> +	indio_dev->modes = INDIO_DIRECT_MODE;
> +	indio_dev->channels = imx8qxp_adc_iio_channels;
> +	indio_dev->num_channels = ARRAY_SIZE(imx8qxp_adc_iio_channels);
> +
> +	ret = devm_request_irq(dev, irq, imx8qxp_adc_isr, 0, dev_name(dev), adc);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed requesting irq, irq = %d\n", irq);
> +		return ret;
> +	}
> +
> +	imx8qxp_adc_feature_prepare(adc);
> +	imx8qxp_adc_reset(adc);
> +
> +	ret = iio_device_register(indio_dev);
> +	if (ret) {
> +		imx8qxp_adc_disable(adc);
> +		dev_err(dev, "Couldn't register the device.\n");
> +		return ret;
> +	}
> +
> +	pm_runtime_set_active(dev);
> +	pm_runtime_set_autosuspend_delay(dev, 50);
> +	pm_runtime_use_autosuspend(dev);
> +	pm_runtime_enable(dev);
> +
>  	return 0;
>  }
>  
>  static int imx8qxp_adc_remove(struct platform_device *pdev)
>  {
> +	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +	struct device *dev = adc->dev;
> +
> +	pm_runtime_get_sync(dev);
> +
> +	iio_device_unregister(indio_dev);
> +
> +	imx8qxp_adc_disable(adc);
> +
> +	pm_runtime_disable(dev);

Looks racey.  Would expect runtime_disable() before
the device is finally turned off with adc_disable() and
then decrement the reference counter.

> +	pm_runtime_put_noidle(dev);
> +
>  	return 0;
>  }
>  
>  static int imx8qxp_adc_runtime_suspend(struct device *dev)
>  {
> +	struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +
> +	imx8qxp_adc_disable(adc);
> +
> +	clk_disable_unprepare(adc->clk);
> +	clk_disable_unprepare(adc->ipg_clk);
> +	regulator_disable(adc->vref);
> +
>  	return 0;
>  }
>  
>  static int imx8qxp_adc_runtime_resume(struct device *dev)
>  {
> +	struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +	int ret;
> +
> +	ret = regulator_enable(adc->vref);
> +	if (ret) {
> +		dev_err(dev, "Can't enable adc reference top voltage, err = %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = clk_prepare_enable(adc->clk);
> +	if (ret) {
> +		dev_err(dev, "Could not prepare or enable clock.\n");
> +		regulator_disable(adc->vref);
Use a pattern like

	goto err_disable_reg;

etc and have a single error handling block at the end of the function.

> +		return ret;
> +	}
> +
> +	ret = clk_prepare_enable(adc->ipg_clk);
> +	if (ret) {
> +		dev_err(dev, "Could not prepare or enable clock.\n");
> +		clk_disable_unprepare(adc->clk);
> +		regulator_disable(adc->vref);
> +		return ret;
> +	}
> +	imx8qxp_adc_reset(adc);
> +
>  	return 0;
>  }
>  

Re: [PATCH 3/6] iio: imx8qxp-adc: Add the detail for NXP i.MX8QuadXPlus ADC driver

[Jonathan Cameron]

On Tue, 31 Aug 2021 01:21:37 +0800
Cai Huoqing <caihuoqing@baidu.com> wrote:

> The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the detail for NXP
> i.MX8QuadXPlus ADC driver which includes: probe/remove/pm_ops/iio_dev.
> 
> Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
> ---
>  drivers/iio/adc/imx8qxp-adc.c | 513 ++++++++++++++++++++++++++++++++++
>  1 file changed, 513 insertions(+)
> 
> diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
> index aec1b45c8fb9..d39bf382c582 100644
> --- a/drivers/iio/adc/imx8qxp-adc.c
> +++ b/drivers/iio/adc/imx8qxp-adc.c
> @@ -20,23 +20,536 @@
>  
>  #define ADC_DRIVER_NAME		"imx8qxp-adc"
>  
> +/* Register map definition */
> +#define ADC_CTRL		0x10
Give a device specific prefix.  The chances of these shadowing naming in
some future ore header is rather high so let us prevent that now.
IMX8QXP_ADC_STAT  etc.

Naming wise it is usually good to clearly distinguish registers from field
names.  There are lots of ways to do this, but a postfix of _REG or _ADR
works well.

> +#define ADC_STAT		0x14
> +#define ADC_IE			0x18
> +#define ADC_DE			0x1c
> +#define ADC_CFG			0x20
> +#define ADC_FCTRL		0x30
> +#define ADC_SWTRIG		0x34
> +#define ADC_TCTRL(tid)		(0xc0 + tid * 4)
> +#define ADC_CMDH(cid)		(0x100 + cid * 8)
> +#define ADC_CMDL(cid)		(0x104 + cid * 8)
> +#define ADC_RESFIFO		0x300
> +#define ADC_TST			0xffc
> +
> +/* ADC bit shift */
> +#define ADC_IE_FWMIE_SHIFT		(0)

All the brackets around individual numbers are unnecessary.

Cleaner and more consistent way to define register fields is
to use masks only (BIT or GENMASK as appropriate) and then use
PREP_FIELD() and GET_FIELD() to manipulate the actual values.

> +#define ADC_CTRL_FIFO_RESET_SHIFT	(8)
> +#define ADC_CTRL_SOFTWARE_RESET_SHIFT	(1)
> +#define ADC_CTRL_ADC_ENABLE		(0)
> +#define ADC_TCTRL_TCMD_SHIFT		(24)
> +#define ADC_TCTRL_TDLY_SHIFT		(16)
> +#define ADC_TCTRL_TPRI_SHIFT		(8)
> +#define ADC_TCTRL_HTEN_SHIFT		(0)
> +#define ADC_CMDL_CSCALE_SHIFT		(8)
> +#define ADC_CMDL_MODE_SHIFT		(7)
> +#define ADC_CMDL_DIFF_SHIFT		(6)
> +#define ADC_CMDL_ABSEL_SHIFT		(5)
> +#define ADC_CMDL_ADCH_SHIFT		(0)
> +#define ADC_CMDH_NEXT_SHIFT		(24)
> +#define ADC_CMDH_LOOP_SHIFT		(16)
> +#define ADC_CMDH_AVGS_SHIFT		(12)
> +#define ADC_CMDH_STS_SHIFT		(8)
> +#define ADC_CMDH_LWI_SHIFT		(7)
> +#define ADC_CMDH_CMPEN_SHIFT		(0)
> +#define ADC_CFG_PWREN_SHIFT		(28)
> +#define ADC_CFG_PUDLY_SHIFT		(16)
> +#define ADC_CFG_REFSEL_SHIFT		(6)
> +#define ADC_CFG_PWRSEL_SHIFT		(4)
> +#define ADC_CFG_TPRICTRL_SHIFT		(0)
> +#define ADC_FCTRL_FWMARK_SHIFT		(16)
> +#define ADC_FCTRL_FWMARK_MASK		(0x1f << 16)
> +#define ADC_FCTRL_FCOUNT_MASK		(0x1f)
> +
> +/* ADC PARAMETER*/
> +#define ADC_CMDL_CHANNEL_SCALE_FULL		(0x3f)
> +#define ADC_CMDL_SEL_A_A_B_CHANNEL		(0)
> +#define ADC_CMDL_STANDARD_RESOLUTION		(0)
> +#define ADC_CMDL_MODE_SINGLE			(0)
> +#define ADC_CMDH_LWI_INCREMENT_DISABLE		(0)
> +#define ADC_CMDH_CMPEN_DISABLE			(0)
> +#define ADC_PAUSE_ENABLE			(0x80000000)
> +#define ADC_TCTRL_TPRI_PRIORITY_HIGH		(0)
> +
> +#define ADC_TCTRL_HTEN_HARDWARE_TIRGGER_DISABLE	(0)
> +
> +#define MAX_CMD (8)
> +#define MAX_TRIG (8)
> +
> +#define ADC_TIMEOUT		msecs_to_jiffies(100)
> +
> +struct imx8qxp_adc_trigger_ctrl {
> +	u32 tcmd;

I'll guess from the shifts above that these are larger than they
would be if reflecting actual possible values. Please use u8 etc
as appropriate.  Or just store these as caches of the registers and use
GET_FIELD and PREP_FIELD to manipulate them.

Mind you, so far I don't know what they are for ;)

> +	u32 tdly;
> +	u32 tpri;
> +	u32 hten;
> +};
> +
> +struct imx8qxp_adc_cmd_l {
> +	u32 scale;
> +	u32 mode;
> +	u32 diff;
> +	u32 absel;
> +	u32 adch;
> +};
> +
> +struct imx8qxp_adc_cmd_h {
> +	u32 next;
> +	u32 loop;
> +	u32 avgs;
> +	u32 sts;
> +	u32 lwi;
> +	u32 cmpen;
> +};
> +
> +struct imx8qxp_adc_cfg {
> +	u32 pwren;
> +	u32 pudly;
> +	u32 refsel;
> +	u32 pwrsel;
> +	u32 tprictrl;
> +};
> +
> +struct imx8qxp_adc {
> +	struct device *dev;
> +	void __iomem *regs;
> +	struct clk *clk;
> +	struct clk *ipg_clk;
> +
> +	u32 vref_uv;
> +	u32 value;
> +	u32 channel_id;
> +	u32 trigger_id;
As mentioned below, a lot of this doesn't seem to be necessary to cache in here.
If we can keep it local in the driver, that would be better.
> +	u32 cmd_id;
> +
> +	struct regulator *vref;
> +	struct imx8qxp_adc_cmd_l adc_cmd_l[MAX_CMD + 1];
> +	struct imx8qxp_adc_cmd_h adc_cmd_h[MAX_CMD + 1];
> +	struct imx8qxp_adc_trigger_ctrl adc_trigger_ctrl[MAX_TRIG + 1];
> +	struct imx8qxp_adc_cfg adc_cfg;
> +	struct completion completion;
> +};
> +
> +#define IMX8QXP_ADC_CHAN(_idx) {				\
> +	.type = IIO_VOLTAGE,					\
> +	.indexed = 1,						\
> +	.channel = (_idx),					\
> +	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
> +	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) |	\
> +				BIT(IIO_CHAN_INFO_SAMP_FREQ),	\
> +}
> +
> +static const struct iio_chan_spec imx8qxp_adc_iio_channels[] = {
> +	IMX8QXP_ADC_CHAN(0),
> +	IMX8QXP_ADC_CHAN(1),
> +	IMX8QXP_ADC_CHAN(2),
> +	IMX8QXP_ADC_CHAN(3),
> +	IMX8QXP_ADC_CHAN(4),
> +	IMX8QXP_ADC_CHAN(5),
> +	IMX8QXP_ADC_CHAN(6),
> +	IMX8QXP_ADC_CHAN(7),
> +};
> +
> +static void imx8qxp_adc_feature_prepare(struct imx8qxp_adc *adc)
> +{
> +	u32 i;
> +
> +	adc->trigger_id = 0;
> +	adc->cmd_id = 0;
> +	adc->channel_id = 0;
> +
> +	for (i = 0; i < MAX_CMD + 1; i++) {
> +		adc->adc_cmd_l[i].scale = 1;
> +		adc->adc_cmd_l[i].mode = 0;
> +		adc->adc_cmd_l[i].diff = 0;
> +		adc->adc_cmd_l[i].absel = 0;
> +		adc->adc_cmd_l[i].adch = 0;
> +		adc->adc_cmd_h[i].next = 0;
> +		adc->adc_cmd_h[i].loop = 0;
> +		adc->adc_cmd_h[i].avgs = 0;
> +		adc->adc_cmd_h[i].sts = 0;
> +		adc->adc_cmd_h[i].lwi = 0;
> +		adc->adc_cmd_h[i].cmpen = 0;
> +	}
> +
> +	for (i = 0; i < MAX_TRIG; i++) {
> +		adc->adc_trigger_ctrl[i].tcmd = 0;
> +		adc->adc_trigger_ctrl[i].tdly = 0;
> +		adc->adc_trigger_ctrl[i].tpri = 0;
> +		adc->adc_trigger_ctrl[i].hten = 0;
> +	}
> +
> +	adc->adc_cfg.pwren = 0;
> +	adc->adc_cfg.pudly = 0;
> +	adc->adc_cfg.refsel = 0;
> +	adc->adc_cfg.pwrsel = 0;
> +	adc->adc_cfg.tprictrl = 0;
> +}
> +
> +static void imx8qxp_adc_reset(struct imx8qxp_adc *adc)
> +{
> +	u32 ctrl;
> +
> +	/*software reset, need to clear the set bit*/
> +	ctrl = readl(adc->regs + ADC_CTRL);
> +	ctrl |= 1 << ADC_CTRL_SOFTWARE_RESET_SHIFT;
> +	writel(ctrl, adc->regs + ADC_CTRL);
> +	udelay(10);
> +	ctrl &= ~(1 << ADC_CTRL_SOFTWARE_RESET_SHIFT);
> +	writel(ctrl, adc->regs + ADC_CTRL);
> +
> +	/* reset the fifo */
> +	ctrl |= 1 << ADC_CTRL_FIFO_RESET_SHIFT;
> +	writel(ctrl, adc->regs + ADC_CTRL);
> +}
> +
> +static void imx8qxp_adc_reg_config(struct imx8qxp_adc *adc)
> +{
> +	u32 adc_cfg, adc_tctrl, adc_cmdl, adc_cmdh;
> +	u32 t_id, c_id;
> +
> +	adc_cfg = adc->adc_cfg.pwren << ADC_CFG_PWREN_SHIFT |
> +		  adc->adc_cfg.pudly << ADC_CFG_PUDLY_SHIFT |
> +		  adc->adc_cfg.refsel << ADC_CFG_REFSEL_SHIFT |
> +		  adc->adc_cfg.pwrsel << ADC_CFG_PWRSEL_SHIFT |
> +		  adc->adc_cfg.tprictrl << ADC_CFG_TPRICTRL_SHIFT;

Lots of FIELD_PREP(), or as I mention above perhaps just put these
directly in place at the point of setting the values in adc->xxx
rather than leaving it to where you write them.
 
> +	writel(adc_cfg, adc->regs + ADC_CFG);
> +
> +	t_id = adc->trigger_id;
> +	adc_tctrl = adc->adc_trigger_ctrl[t_id].tcmd << ADC_TCTRL_TCMD_SHIFT |
> +		    adc->adc_trigger_ctrl[t_id].tdly << ADC_TCTRL_TDLY_SHIFT |
> +		    adc->adc_trigger_ctrl[t_id].tpri << ADC_TCTRL_TPRI_SHIFT |
> +		    adc->adc_trigger_ctrl[t_id].hten << ADC_TCTRL_HTEN_SHIFT;
> +	writel(adc_tctrl, adc->regs + ADC_TCTRL(t_id));
> +
> +	c_id = adc->cmd_id - 1;
> +	adc_cmdl = adc->adc_cmd_l[c_id].scale << ADC_CMDL_CSCALE_SHIFT |
> +		   adc->adc_cmd_l[c_id].mode << ADC_CMDL_MODE_SHIFT |
> +		   adc->adc_cmd_l[c_id].diff << ADC_CMDL_DIFF_SHIFT |
> +		   adc->adc_cmd_l[c_id].absel << ADC_CMDL_ABSEL_SHIFT |
> +		   adc->adc_cmd_l[c_id].adch << ADC_CMDL_ADCH_SHIFT;
> +	writel(adc_cmdl, adc->regs + ADC_CMDL(c_id));
> +
> +	adc_cmdh = adc->adc_cmd_h[c_id].next << ADC_CMDH_NEXT_SHIFT |
> +		   adc->adc_cmd_h[c_id].loop << ADC_CMDH_LOOP_SHIFT |
> +		   adc->adc_cmd_h[c_id].avgs << ADC_CMDH_AVGS_SHIFT |
> +		   adc->adc_cmd_h[c_id].sts << ADC_CMDH_STS_SHIFT |
> +		   adc->adc_cmd_h[c_id].lwi << ADC_CMDH_LWI_SHIFT |
> +		   adc->adc_cmd_h[c_id].cmpen << ADC_CMDH_CMPEN_SHIFT;
> +	writel(adc_cmdh, adc->regs + ADC_CMDH(c_id));
> +}
> +
> +static void imx8qxp_adc_mode_config(struct imx8qxp_adc *adc)
> +{
> +	u32 cmd_id, trigger_id, channel_id;
> +
> +	channel_id = adc->channel_id;
> +	cmd_id = adc->cmd_id - 1;

Call the local variable something different as it's clearly not
what would be thought of as cmd_id elsewhere in the driver.

> +	trigger_id = adc->trigger_id;
> +
> +	/* config the cmd */
> +	adc->adc_cmd_l[cmd_id].scale = ADC_CMDL_CHANNEL_SCALE_FULL;
> +	adc->adc_cmd_l[cmd_id].mode = ADC_CMDL_STANDARD_RESOLUTION;
> +	adc->adc_cmd_l[cmd_id].diff = ADC_CMDL_MODE_SINGLE;
> +	adc->adc_cmd_l[cmd_id].absel = ADC_CMDL_SEL_A_A_B_CHANNEL;
> +	adc->adc_cmd_l[cmd_id].adch = channel_id;
> +
> +	adc->adc_cmd_h[cmd_id].next = 0;
> +	adc->adc_cmd_h[cmd_id].loop = 0;
> +	adc->adc_cmd_h[cmd_id].avgs = 7;
> +	adc->adc_cmd_h[cmd_id].sts = 0;
> +	adc->adc_cmd_h[cmd_id].lwi = ADC_CMDH_LWI_INCREMENT_DISABLE;
> +	adc->adc_cmd_h[cmd_id].cmpen = ADC_CMDH_CMPEN_DISABLE;
> +
> +	/* config the trigger control */
> +	adc->adc_trigger_ctrl[trigger_id].tcmd = adc->cmd_id;
> +	adc->adc_trigger_ctrl[trigger_id].tdly = 0;
> +	adc->adc_trigger_ctrl[trigger_id].tpri = ADC_TCTRL_TPRI_PRIORITY_HIGH;
> +	adc->adc_trigger_ctrl[trigger_id].hten = ADC_TCTRL_HTEN_HARDWARE_TIRGGER_DISABLE;
> +
> +	/* ADC configuration */
> +	adc->adc_cfg.pwren = 1;
> +	adc->adc_cfg.pudly = 0x80;
> +	adc->adc_cfg.refsel = 0;
> +	adc->adc_cfg.pwrsel = 3;
> +	adc->adc_cfg.tprictrl = 0;
> +
> +	imx8qxp_adc_reg_config(adc);
> +}
> +
> +static void imx8qxp_adc_fifo_config(struct imx8qxp_adc *adc)
> +{
> +	u32 fifo_ctrl, interrupt_en;
> +
> +	fifo_ctrl = readl(adc->regs + ADC_FCTRL);
> +	fifo_ctrl &= ~ADC_FCTRL_FWMARK_MASK;
> +	/* set the watermark level to 1 */
> +	fifo_ctrl |= 0 << ADC_FCTRL_FWMARK_SHIFT;
FIELD_PREP()

> +	writel(fifo_ctrl, adc->regs + ADC_FCTRL);
> +
> +	/* FIFO Watermark Interrupt Enable */
> +	interrupt_en = readl(adc->regs + ADC_IE);
> +	interrupt_en |= 1 << ADC_IE_FWMIE_SHIFT;
FIELD_PREP()

> +	writel(interrupt_en, adc->regs + ADC_IE);
> +}
> +
> +static void imx8qxp_adc_disable(struct imx8qxp_adc *adc)
> +{
> +	u32 ctrl;
> +
> +	ctrl = readl(adc->regs + ADC_CTRL) & ~(1 << ADC_CTRL_ADC_ENABLE);

~BIT(ADC_CTRL_ADC_ENABLE) or appropriate FIELD_PREP

> +	writel(ctrl, adc->regs + ADC_CTRL);
> +}
> +
> +static int imx8qxp_adc_read_raw(struct iio_dev *indio_dev, struct iio_chan_spec const *chan,
> +				int *val, int *val2, long mask)
> +{
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +	struct device *dev = adc->dev;
> +
> +	u32 channel;
> +	u32 ctrl;
> +	long ret;
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_RAW:
> +		pm_runtime_get_sync(dev);
> +
> +		mutex_lock(&indio_dev->mlock);
Please do not use mlock directly.  If you are protecting driver local data
(so stuff in iio_priv()) or hardware resources define your own local lock
in iio_priv() with well documented scope.

If the aim is to prevent racing with IIO core state changes, then use
iio_device_claim_direct().  That only applies if the driver supports buffered
mode as otherwise you won't get state changes.

> +		reinit_completion(&adc->completion);
> +
> +		channel = chan->channel & 0x07;
> +		adc->channel_id = channel;
> +		adc->cmd_id = 1;
> +		adc->trigger_id = 0;
> +		imx8qxp_adc_mode_config(adc);

Why not pass channel, cmd_id and trigger_id into this function rather than using
state in iio_priv() for them?  I checked adc->channel_id and it is only used
in that function so you should not have it in the iio_priv() structure at all.
For the others I haven't checked but would guess similar?

> +
> +		imx8qxp_adc_fifo_config(adc);
> +
> +		/* adc enable */
> +		ctrl = readl(adc->regs + ADC_CTRL) | (1 << ADC_CTRL_ADC_ENABLE);
> +		writel(ctrl, adc->regs + ADC_CTRL);
> +		/* adc start */
> +		writel(1 << adc->trigger_id, adc->regs + ADC_SWTRIG);
> +
> +		ret = wait_for_completion_interruptible_timeout
> +				(&adc->completion, ADC_TIMEOUT);

Readabilty of this line is hurt by it being broken up so as long as it is under 100 chars
I'd prefer it one line.

> +
> +		pm_runtime_mark_last_busy(dev);
> +		pm_runtime_put_sync_autosuspend(dev);
> +
> +		if (ret == 0) {
> +			mutex_unlock(&indio_dev->mlock);
> +			return -ETIMEDOUT;
> +		}
> +		if (ret < 0) {
> +			mutex_unlock(&indio_dev->mlock);
> +			return ret;
> +		}
> +
> +		*val = adc->value;
As mentioned below, why not do the register read here rather than caching it before
calling complete()?

> +		mutex_unlock(&indio_dev->mlock);
> +		return IIO_VAL_INT;
> +
> +	case IIO_CHAN_INFO_SCALE:
> +		adc->vref_uv = regulator_get_voltage(adc->vref);
Why cache it? Use a local variable.

> +		*val = adc->vref_uv / 1000;
> +		*val2 = 12;
> +		return IIO_VAL_FRACTIONAL_LOG2;
> +
> +	case IIO_CHAN_INFO_SAMP_FREQ:
> +		*val = clk_get_rate(adc->clk) / 3;
> +		return IIO_VAL_INT;
> +
> +	default:
> +		return -EINVAL;
> +	}
> +}
> +
> +static irqreturn_t imx8qxp_adc_isr(int irq, void *dev_id)
> +{
> +	struct imx8qxp_adc *adc = (struct imx8qxp_adc *)dev_id;
> +
> +	u32 fifo_count;
> +
> +	fifo_count = readl(adc->regs + ADC_FCTRL)
> +			& ADC_FCTRL_FCOUNT_MASK;

One line as still well under 80 chars.  As mentioned above, FIELD_GET()
preferred as means the reviewer / reader doesn't need to go check this
mask is from bit 0 upwards.

> +
> +	if (fifo_count) {
> +		adc->value = (readl(adc->regs + ADC_RESFIFO) & 0xffff) >> 3;
> +		complete(&adc->completion);

Why do the adc->value read here rather than in the completion?
If there is a potential race I'd expect it to also affect adc->value


> +	}
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int imx8qxp_adc_reg_access(struct iio_dev *indio_dev, unsigned int reg,
> +				  unsigned int writeval, unsigned int *readval)
> +{
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +	struct device *dev = adc->dev;
> +
> +	if (!readval || reg % 4 || reg > ADC_TST)
> +		return -EINVAL;
> +
> +	pm_runtime_get_sync(dev);
> +
> +	*readval = readl(adc->regs + reg);
> +
> +	pm_runtime_mark_last_busy(dev);
> +	pm_runtime_put_sync_autosuspend(dev);
> +
> +	return 0;
> +}
> +
> +static const struct iio_info imx8qxp_adc_iio_info = {
> +	.read_raw = &imx8qxp_adc_read_raw,
> +	.debugfs_reg_access = &imx8qxp_adc_reg_access,
> +};
> +
>  static int imx8qxp_adc_probe(struct platform_device *pdev)
>  {
> +	struct imx8qxp_adc *adc;
> +	struct iio_dev *indio_dev;
> +	struct device *dev = &pdev->dev;
> +	int irq;
> +	int ret;
> +
> +	indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
> +	if (!indio_dev) {
> +		dev_err(dev, "Failed allocating iio device\n");
> +		return -ENOMEM;
> +	}
> +
> +	adc = iio_priv(indio_dev);
> +	adc->dev = dev;
> +
> +	adc->regs = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(adc->regs))
> +		return PTR_ERR(adc->regs);
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0)
> +		return irq;
> +
> +	adc->clk = devm_clk_get(dev, "per");
> +	if (IS_ERR(adc->clk)) {
> +		ret = PTR_ERR(adc->clk);
> +		dev_err(dev, "Failed getting clock, err = %d\n", ret);
> +		return ret;
> +	}
> +
> +	adc->ipg_clk = devm_clk_get(dev, "ipg");
> +	if (IS_ERR(adc->ipg_clk)) {
> +		ret = PTR_ERR(adc->ipg_clk);
> +		dev_err(dev, "Failed getting clock, err = %d\n", ret);
> +		return ret;
> +	}
> +
> +	adc->vref = devm_regulator_get(dev, "vref");
> +	if (IS_ERR(adc->vref)) {
> +		ret = PTR_ERR(adc->vref);
> +		dev_err(dev,
> +			"Failed getting reference voltage, err = %d\n", ret);
> +		return ret;
> +	}
> +
> +	platform_set_drvdata(pdev, indio_dev);
> +
> +	init_completion(&adc->completion);
> +
> +	indio_dev->name = dev_name(dev);
> +	indio_dev->info = &imx8qxp_adc_iio_info;
> +	indio_dev->modes = INDIO_DIRECT_MODE;
> +	indio_dev->channels = imx8qxp_adc_iio_channels;
> +	indio_dev->num_channels = ARRAY_SIZE(imx8qxp_adc_iio_channels);
> +
> +	ret = devm_request_irq(dev, irq, imx8qxp_adc_isr, 0, dev_name(dev), adc);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed requesting irq, irq = %d\n", irq);
> +		return ret;
> +	}
> +
> +	imx8qxp_adc_feature_prepare(adc);
> +	imx8qxp_adc_reset(adc);
> +
> +	ret = iio_device_register(indio_dev);
> +	if (ret) {
> +		imx8qxp_adc_disable(adc);
> +		dev_err(dev, "Couldn't register the device.\n");
> +		return ret;
> +	}
> +
> +	pm_runtime_set_active(dev);
> +	pm_runtime_set_autosuspend_delay(dev, 50);
> +	pm_runtime_use_autosuspend(dev);
> +	pm_runtime_enable(dev);
> +
>  	return 0;
>  }
>  
>  static int imx8qxp_adc_remove(struct platform_device *pdev)
>  {
> +	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +	struct device *dev = adc->dev;
> +
> +	pm_runtime_get_sync(dev);
> +
> +	iio_device_unregister(indio_dev);
> +
> +	imx8qxp_adc_disable(adc);
> +
> +	pm_runtime_disable(dev);

Looks racey.  Would expect runtime_disable() before
the device is finally turned off with adc_disable() and
then decrement the reference counter.

> +	pm_runtime_put_noidle(dev);
> +
>  	return 0;
>  }
>  
>  static int imx8qxp_adc_runtime_suspend(struct device *dev)
>  {
> +	struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +
> +	imx8qxp_adc_disable(adc);
> +
> +	clk_disable_unprepare(adc->clk);
> +	clk_disable_unprepare(adc->ipg_clk);
> +	regulator_disable(adc->vref);
> +
>  	return 0;
>  }
>  
>  static int imx8qxp_adc_runtime_resume(struct device *dev)
>  {
> +	struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct imx8qxp_adc *adc = iio_priv(indio_dev);
> +	int ret;
> +
> +	ret = regulator_enable(adc->vref);
> +	if (ret) {
> +		dev_err(dev, "Can't enable adc reference top voltage, err = %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = clk_prepare_enable(adc->clk);
> +	if (ret) {
> +		dev_err(dev, "Could not prepare or enable clock.\n");
> +		regulator_disable(adc->vref);
Use a pattern like

	goto err_disable_reg;

etc and have a single error handling block at the end of the function.

> +		return ret;
> +	}
> +
> +	ret = clk_prepare_enable(adc->ipg_clk);
> +	if (ret) {
> +		dev_err(dev, "Could not prepare or enable clock.\n");
> +		clk_disable_unprepare(adc->clk);
> +		regulator_disable(adc->vref);
> +		return ret;
> +	}
> +	imx8qxp_adc_reset(adc);
> +
>  	return 0;
>  }
>  


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/6] dt-bindings: iio: adc: Add the binding documentation for NXP IMX8QXP ADC

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the binding
documentation for NXP IMX8QXP ADC

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 .../bindings/iio/adc/nxp,imx8qxp-adc.yaml     | 85 +++++++++++++++++++
 1 file changed, 85 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml

diff --git a/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml b/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
new file mode 100644
index 000000000000..542329e6a785
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/nxp,imx8qxp-adc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP IMX8QXP ADC bindings
+
+maintainers:
+  - Cai Huoqing <caihuoqing@baidu.com>
+
+description:
+  Supports the ADC found on the IMX8QXP SoC.
+
+properties:
+  compatible:
+    const: nxp,imx8qxp-adc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: per
+      - const: ipg
+
+  assigned-clocks:
+    maxItems: 1
+
+  assigned-clocks-rate:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  status:
+    const: disable
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupts-parent
+  - clocks
+  - clock-names
+  - assigned-clocks
+  - assigned-clock-rates
+  - power-domains
+  - state
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/firmware/imx/rsrc.h>
+    soc {
+        #address-cells = <1>;
+        #size-cells = <1>;
+	 adc@5a880000 {
+            compatible = "nxp,imx8qxp-adc";
+            reg = <0x0 0x5a880000 0x0 0x10000>;
+            interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&clk IMX_SC_R_ADC_0>,
+                     <&clk IMX_ADMA_LPCG_ADC_0_IPG_CLK>;
+            clock-names = "per", "ipg";
+            assigned-clocks = <&clk IMX_SC_R_ADC_0>;
+            assigned-clock-rates = <24000000>;
+            power-domains = <&pm, IMX_SC_R_ADC_0>;
+            status = "disabled";
+            #io-channel-cells = <1>
+	 };
+    };
+...
-- 
2.25.1

[PATCH 4/6] dt-bindings: iio: adc: Add the binding documentation for NXP IMX8QXP ADC

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the binding
documentation for NXP IMX8QXP ADC

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 .../bindings/iio/adc/nxp,imx8qxp-adc.yaml     | 85 +++++++++++++++++++
 1 file changed, 85 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml

diff --git a/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml b/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
new file mode 100644
index 000000000000..542329e6a785
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/nxp,imx8qxp-adc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP IMX8QXP ADC bindings
+
+maintainers:
+  - Cai Huoqing <caihuoqing@baidu.com>
+
+description:
+  Supports the ADC found on the IMX8QXP SoC.
+
+properties:
+  compatible:
+    const: nxp,imx8qxp-adc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: per
+      - const: ipg
+
+  assigned-clocks:
+    maxItems: 1
+
+  assigned-clocks-rate:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  status:
+    const: disable
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupts-parent
+  - clocks
+  - clock-names
+  - assigned-clocks
+  - assigned-clock-rates
+  - power-domains
+  - state
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/firmware/imx/rsrc.h>
+    soc {
+        #address-cells = <1>;
+        #size-cells = <1>;
+	 adc@5a880000 {
+            compatible = "nxp,imx8qxp-adc";
+            reg = <0x0 0x5a880000 0x0 0x10000>;
+            interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&clk IMX_SC_R_ADC_0>,
+                     <&clk IMX_ADMA_LPCG_ADC_0_IPG_CLK>;
+            clock-names = "per", "ipg";
+            assigned-clocks = <&clk IMX_SC_R_ADC_0>;
+            assigned-clock-rates = <24000000>;
+            power-domains = <&pm, IMX_SC_R_ADC_0>;
+            status = "disabled";
+            #io-channel-cells = <1>
+	 };
+    };
+...
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/6] dt-bindings: iio: adc: Add the binding documentation for NXP IMX8QXP ADC

[Rob Herring]

On Tue, 31 Aug 2021 01:21:38 +0800, Cai Huoqing wrote:
> The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the binding
> documentation for NXP IMX8QXP ADC
> 
> Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
> ---
>  .../bindings/iio/adc/nxp,imx8qxp-adc.yaml     | 85 +++++++++++++++++++
>  1 file changed, 85 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
make[1]: *** Deleting file 'Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.example.dts'
Traceback (most recent call last):
  File "/usr/local/bin/dt-extract-example", line 45, in <module>
    binding = yaml.load(open(args.yamlfile, encoding='utf-8').read())
  File "/usr/local/lib/python3.8/dist-packages/ruamel/yaml/main.py", line 434, in load
    return constructor.get_single_data()
  File "/usr/local/lib/python3.8/dist-packages/ruamel/yaml/constructor.py", line 120, in get_single_data
    node = self.composer.get_single_node()
  File "_ruamel_yaml.pyx", line 706, in _ruamel_yaml.CParser.get_single_node
  File "_ruamel_yaml.pyx", line 724, in _ruamel_yaml.CParser._compose_document
  File "_ruamel_yaml.pyx", line 775, in _ruamel_yaml.CParser._compose_node
  File "_ruamel_yaml.pyx", line 889, in _ruamel_yaml.CParser._compose_mapping_node
  File "_ruamel_yaml.pyx", line 773, in _ruamel_yaml.CParser._compose_node
  File "_ruamel_yaml.pyx", line 848, in _ruamel_yaml.CParser._compose_sequence_node
  File "_ruamel_yaml.pyx", line 904, in _ruamel_yaml.CParser._parse_next_event
ruamel.yaml.scanner.ScannerError: while scanning a block scalar
  in "<unicode string>", line 65, column 5
found a tab character where an indentation space is expected
  in "<unicode string>", line 71, column 1
make[1]: *** [Documentation/devicetree/bindings/Makefile:20: Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.example.dts] Error 1
make[1]: *** Waiting for unfinished jobs....
./Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml:  while scanning a block scalar
  in "<unicode string>", line 65, column 5
found a tab character where an indentation space is expected
  in "<unicode string>", line 71, column 1
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml: ignoring, error parsing file
warning: no schema found in file: ./Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
make: *** [Makefile:1419: dt_binding_check] Error 2

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/1522287

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.

Re: [PATCH 4/6] dt-bindings: iio: adc: Add the binding documentation for NXP IMX8QXP ADC

[Rob Herring]

On Tue, 31 Aug 2021 01:21:38 +0800, Cai Huoqing wrote:
> The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the binding
> documentation for NXP IMX8QXP ADC
> 
> Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
> ---
>  .../bindings/iio/adc/nxp,imx8qxp-adc.yaml     | 85 +++++++++++++++++++
>  1 file changed, 85 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
make[1]: *** Deleting file 'Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.example.dts'
Traceback (most recent call last):
  File "/usr/local/bin/dt-extract-example", line 45, in <module>
    binding = yaml.load(open(args.yamlfile, encoding='utf-8').read())
  File "/usr/local/lib/python3.8/dist-packages/ruamel/yaml/main.py", line 434, in load
    return constructor.get_single_data()
  File "/usr/local/lib/python3.8/dist-packages/ruamel/yaml/constructor.py", line 120, in get_single_data
    node = self.composer.get_single_node()
  File "_ruamel_yaml.pyx", line 706, in _ruamel_yaml.CParser.get_single_node
  File "_ruamel_yaml.pyx", line 724, in _ruamel_yaml.CParser._compose_document
  File "_ruamel_yaml.pyx", line 775, in _ruamel_yaml.CParser._compose_node
  File "_ruamel_yaml.pyx", line 889, in _ruamel_yaml.CParser._compose_mapping_node
  File "_ruamel_yaml.pyx", line 773, in _ruamel_yaml.CParser._compose_node
  File "_ruamel_yaml.pyx", line 848, in _ruamel_yaml.CParser._compose_sequence_node
  File "_ruamel_yaml.pyx", line 904, in _ruamel_yaml.CParser._parse_next_event
ruamel.yaml.scanner.ScannerError: while scanning a block scalar
  in "<unicode string>", line 65, column 5
found a tab character where an indentation space is expected
  in "<unicode string>", line 71, column 1
make[1]: *** [Documentation/devicetree/bindings/Makefile:20: Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.example.dts] Error 1
make[1]: *** Waiting for unfinished jobs....
./Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml:  while scanning a block scalar
  in "<unicode string>", line 65, column 5
found a tab character where an indentation space is expected
  in "<unicode string>", line 71, column 1
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml: ignoring, error parsing file
warning: no schema found in file: ./Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
make: *** [Makefile:1419: dt_binding_check] Error 2

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/1522287

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/6] dt-bindings: iio: adc: Add the binding documentation for NXP IMX8QXP ADC

[Jonathan Cameron]

On Tue, 31 Aug 2021 01:21:38 +0800
Cai Huoqing <caihuoqing@baidu.com> wrote:

> The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the binding
> documentation for NXP IMX8QXP ADC
> 
> Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
> ---
>  .../bindings/iio/adc/nxp,imx8qxp-adc.yaml     | 85 +++++++++++++++++++
>  1 file changed, 85 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml b/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
> new file mode 100644
> index 000000000000..542329e6a785
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
> @@ -0,0 +1,85 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/adc/nxp,imx8qxp-adc.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP IMX8QXP ADC bindings
> +
> +maintainers:
> +  - Cai Huoqing <caihuoqing@baidu.com>
> +
> +description:
> +  Supports the ADC found on the IMX8QXP SoC.
> +
> +properties:
> +  compatible:
> +    const: nxp,imx8qxp-adc
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 2
> +
> +  clock-names:
> +    items:
> +      - const: per
> +      - const: ipg
> +
> +  assigned-clocks:
> +    maxItems: 1
> +
> +  assigned-clocks-rate:
> +    maxItems: 1
> +
> +  power-domains:
> +    maxItems: 1
> +
> +  status:
> +    const: disable
> +
> +  "#io-channel-cells":
> +    const: 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - interrupts-parent
> +  - clocks
> +  - clock-names
> +  - assigned-clocks
> +  - assigned-clock-rates
> +  - power-domains
> +  - state
> +  - "#address-cells"
> +  - "#size-cells"
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/firmware/imx/rsrc.h>
> +    soc {
> +        #address-cells = <1>;
> +        #size-cells = <1>;
> +	 adc@5a880000 {
Clearly some indentation issues here.
> +            compatible = "nxp,imx8qxp-adc";
> +            reg = <0x0 0x5a880000 0x0 0x10000>;
> +            interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
> +            clocks = <&clk IMX_SC_R_ADC_0>,
> +                     <&clk IMX_ADMA_LPCG_ADC_0_IPG_CLK>;
> +            clock-names = "per", "ipg";
> +            assigned-clocks = <&clk IMX_SC_R_ADC_0>;
> +            assigned-clock-rates = <24000000>;
> +            power-domains = <&pm, IMX_SC_R_ADC_0>;
> +            status = "disabled";

Don't mark the example disabled.

> +            #io-channel-cells = <1>
> +	 };
> +    };
> +...

Re: [PATCH 4/6] dt-bindings: iio: adc: Add the binding documentation for NXP IMX8QXP ADC

[Jonathan Cameron]

On Tue, 31 Aug 2021 01:21:38 +0800
Cai Huoqing <caihuoqing@baidu.com> wrote:

> The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add the binding
> documentation for NXP IMX8QXP ADC
> 
> Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
> ---
>  .../bindings/iio/adc/nxp,imx8qxp-adc.yaml     | 85 +++++++++++++++++++
>  1 file changed, 85 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml b/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
> new file mode 100644
> index 000000000000..542329e6a785
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
> @@ -0,0 +1,85 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/adc/nxp,imx8qxp-adc.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP IMX8QXP ADC bindings
> +
> +maintainers:
> +  - Cai Huoqing <caihuoqing@baidu.com>
> +
> +description:
> +  Supports the ADC found on the IMX8QXP SoC.
> +
> +properties:
> +  compatible:
> +    const: nxp,imx8qxp-adc
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 2
> +
> +  clock-names:
> +    items:
> +      - const: per
> +      - const: ipg
> +
> +  assigned-clocks:
> +    maxItems: 1
> +
> +  assigned-clocks-rate:
> +    maxItems: 1
> +
> +  power-domains:
> +    maxItems: 1
> +
> +  status:
> +    const: disable
> +
> +  "#io-channel-cells":
> +    const: 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - interrupts-parent
> +  - clocks
> +  - clock-names
> +  - assigned-clocks
> +  - assigned-clock-rates
> +  - power-domains
> +  - state
> +  - "#address-cells"
> +  - "#size-cells"
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/firmware/imx/rsrc.h>
> +    soc {
> +        #address-cells = <1>;
> +        #size-cells = <1>;
> +	 adc@5a880000 {
Clearly some indentation issues here.
> +            compatible = "nxp,imx8qxp-adc";
> +            reg = <0x0 0x5a880000 0x0 0x10000>;
> +            interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
> +            clocks = <&clk IMX_SC_R_ADC_0>,
> +                     <&clk IMX_ADMA_LPCG_ADC_0_IPG_CLK>;
> +            clock-names = "per", "ipg";
> +            assigned-clocks = <&clk IMX_SC_R_ADC_0>;
> +            assigned-clock-rates = <24000000>;
> +            power-domains = <&pm, IMX_SC_R_ADC_0>;
> +            status = "disabled";

Don't mark the example disabled.

> +            #io-channel-cells = <1>
> +	 };
> +    };
> +...


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5/6] MAINTAINERS: Add the driver info of the NXP IMX8QXP ADC

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP. After adding
the driver support for it, I add the driver info of the
NXP IMX8QXP ADC to MAINTAINERS file.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 MAINTAINERS | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 0147a85bc38b..058394fd3387 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13463,6 +13463,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/display/imx/nxp,imx8mq-dcss.yaml
 F:	drivers/gpu/drm/imx/dcss/
 
+NXP i.MX 8QXP ADC DRIVER
+M:	Cai Huoqing <caihuoqing@baidu.com>
+L:	linux-iio@vger.kernel.org
+S:	Supported
+F:	Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
+F:	drivers/iio/adc/imx8qxp-adc.c
+
 NXP PF8100/PF8121A/PF8200 PMIC REGULATOR DEVICE DRIVER
 M:	Jagan Teki <jagan@amarulasolutions.com>
 S:	Maintained
-- 
2.25.1

[PATCH 5/6] MAINTAINERS: Add the driver info of the NXP IMX8QXP ADC

[Cai Huoqing]

The NXP i.MX 8QuadXPlus SOC has a new ADC IP. After adding
the driver support for it, I add the driver info of the
NXP IMX8QXP ADC to MAINTAINERS file.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 MAINTAINERS | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 0147a85bc38b..058394fd3387 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13463,6 +13463,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/display/imx/nxp,imx8mq-dcss.yaml
 F:	drivers/gpu/drm/imx/dcss/
 
+NXP i.MX 8QXP ADC DRIVER
+M:	Cai Huoqing <caihuoqing@baidu.com>
+L:	linux-iio@vger.kernel.org
+S:	Supported
+F:	Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml
+F:	drivers/iio/adc/imx8qxp-adc.c
+
 NXP PF8100/PF8121A/PF8200 PMIC REGULATOR DEVICE DRIVER
 M:	Jagan Teki <jagan@amarulasolutions.com>
 S:	Maintained
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 6/6] iio: imx8qxp-adc: Add the copyright for NXP i.MX8QuadXPlus ADC driver

[Cai Huoqing]

Add the copyright for NXP i.MX8QuadXPlus ADC driver.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 drivers/iio/adc/imx8qxp-adc.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
index d39bf382c582..dbb6761f1768 100644
--- a/drivers/iio/adc/imx8qxp-adc.c
+++ b/drivers/iio/adc/imx8qxp-adc.c
@@ -1,6 +1,14 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
  * NXP i.MX8QXP ADC driver
+ *
+ * Based on the work of Haibo Chen <haibo.chen@nxp.com>
+ * The initial developer of the original code is Haibo Chen.
+ * Portions created by Haibo Chen are Copyright (C) 2018 NXP.
+ * All Rights Reserved.
+ *
+ * Copyright (C) 2018 NXP
+ * Copyright (C) 2021 Cai Huoqing
  */
 
 #include <linux/clk.h>
-- 
2.25.1

[PATCH 6/6] iio: imx8qxp-adc: Add the copyright for NXP i.MX8QuadXPlus ADC driver

[Cai Huoqing]

Add the copyright for NXP i.MX8QuadXPlus ADC driver.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
---
 drivers/iio/adc/imx8qxp-adc.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/iio/adc/imx8qxp-adc.c b/drivers/iio/adc/imx8qxp-adc.c
index d39bf382c582..dbb6761f1768 100644
--- a/drivers/iio/adc/imx8qxp-adc.c
+++ b/drivers/iio/adc/imx8qxp-adc.c
@@ -1,6 +1,14 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
  * NXP i.MX8QXP ADC driver
+ *
+ * Based on the work of Haibo Chen <haibo.chen@nxp.com>
+ * The initial developer of the original code is Haibo Chen.
+ * Portions created by Haibo Chen are Copyright (C) 2018 NXP.
+ * All Rights Reserved.
+ *
+ * Copyright (C) 2018 NXP
+ * Copyright (C) 2021 Cai Huoqing
  */
 
 #include <linux/clk.h>
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel