* [PATCH] udoo_neo: Move to DM for REGUALTOR/PMIC/I2C drivers
@ 2021-12-22 0:17 Peter Robinson
2021-12-22 0:38 ` Fabio Estevam
0 siblings, 1 reply; 3+ messages in thread
From: Peter Robinson @ 2021-12-22 0:17 UTC (permalink / raw)
To: Breno Lima, Francesco Montefoschi, Fabio Estevam, u-boot; +Cc: Peter Robinson
This moves over the PMIC power init to DM and the associated i2c and
regulator bits.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
---
board/udoo/neo/neo.c | 139 +++----------------------------------
configs/udoo_neo_defconfig | 10 +--
include/configs/udoo_neo.h | 5 --
3 files changed, 15 insertions(+), 139 deletions(-)
diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c
index 62f81fff68..d374b86b5d 100644
--- a/board/udoo/neo/neo.c
+++ b/board/udoo/neo/neo.c
@@ -51,11 +51,6 @@ enum {
PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE)
-
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
@@ -81,135 +76,25 @@ int dram_init(void)
return 0;
}
-#ifdef CONFIG_SYS_I2C_MXC
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-/* I2C1 for PMIC */
-static struct i2c_pads_info i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
- .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
- .gp = IMX_GPIO_NR(1, 0),
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
- .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
- .gp = IMX_GPIO_NR(1, 1),
- },
-};
-#endif
-
-#if CONFIG_IS_ENABLED(POWER_LEGACY)
int power_init_board(void)
{
- struct pmic *p;
- int ret;
- unsigned int reg, rev_id;
-
- ret = power_pfuze3000_init(PFUZE3000_I2C_BUS);
- if (ret)
- return ret;
-
- p = pmic_get("PFUZE3000");
- ret = pmic_probe(p);
- if (ret)
- return ret;
+ struct udevice *dev;
+ int ret, dev_id, rev_id;
- pmic_reg_read(p, PFUZE3000_DEVICEID, ®);
- pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
- printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
-
- /* disable Low Power Mode during standby mode */
- pmic_reg_read(p, PFUZE3000_LDOGCTL, ®);
- reg |= 0x1;
- ret = pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
- if (ret)
+ ret = pmic_get("pfuze3000@8", &dev);
+ if (ret == -ENODEV)
+ return 0;
+ if (ret != 0)
return ret;
- ret = pmic_reg_write(p, PFUZE3000_SW1AMODE, 0xc);
- if (ret)
- return ret;
+ dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
+ rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
+ printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
- ret = pmic_reg_write(p, PFUZE3000_SW1BMODE, 0xc);
- if (ret)
- return ret;
-
- ret = pmic_reg_write(p, PFUZE3000_SW2MODE, 0xc);
- if (ret)
- return ret;
-
- ret = pmic_reg_write(p, PFUZE3000_SW3MODE, 0xc);
- if (ret)
- return ret;
-
- /* set SW1A standby voltage 0.975V */
- pmic_reg_read(p, PFUZE3000_SW1ASTBY, ®);
- reg &= ~0x3f;
- reg |= PFUZE3000_SW1AB_SETP(9750);
- ret = pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg);
- if (ret)
- return ret;
-
- /* set SW1B standby voltage 0.975V */
- pmic_reg_read(p, PFUZE3000_SW1BSTBY, ®);
- reg &= ~0x3f;
- reg |= PFUZE3000_SW1AB_SETP(9750);
- ret = pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg);
- if (ret)
- return ret;
-
- /* set SW1A/VDD_ARM_IN step ramp up time from 16us to 4us/25mV */
- pmic_reg_read(p, PFUZE3000_SW1ACONF, ®);
- reg &= ~0xc0;
- reg |= 0x40;
- ret = pmic_reg_write(p, PFUZE3000_SW1ACONF, reg);
- if (ret)
- return ret;
-
- /* set SW1B/VDD_SOC_IN step ramp up time from 16us to 4us/25mV */
- pmic_reg_read(p, PFUZE3000_SW1BCONF, ®);
- reg &= ~0xc0;
- reg |= 0x40;
- ret = pmic_reg_write(p, PFUZE3000_SW1BCONF, reg);
- if (ret)
- return ret;
-
- /* set VDD_ARM_IN to 1.350V */
- pmic_reg_read(p, PFUZE3000_SW1AVOLT, ®);
- reg &= ~0x3f;
- reg |= PFUZE3000_SW1AB_SETP(13500);
- ret = pmic_reg_write(p, PFUZE3000_SW1AVOLT, reg);
- if (ret)
- return ret;
-
- /* set VDD_SOC_IN to 1.350V */
- pmic_reg_read(p, PFUZE3000_SW1BVOLT, ®);
- reg &= ~0x3f;
- reg |= PFUZE3000_SW1AB_SETP(13500);
- ret = pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg);
- if (ret)
- return ret;
-
- /* set DDR_1_5V to 1.350V */
- pmic_reg_read(p, PFUZE3000_SW3VOLT, ®);
- reg &= ~0x0f;
- reg |= PFUZE3000_SW3_SETP(13500);
- ret = pmic_reg_write(p, PFUZE3000_SW3VOLT, reg);
- if (ret)
- return ret;
-
- /* set VGEN2_1V5 to 1.5V */
- pmic_reg_read(p, PFUZE3000_VLDO2CTL, ®);
- reg &= ~0x0f;
- reg |= PFUZE3000_VLDO_SETP(15000);
- /* enable */
- reg |= 0x10;
- ret = pmic_reg_write(p, PFUZE3000_VLDO2CTL, reg);
- if (ret)
- return ret;
+ pmic_clrsetbits(dev, PFUZE3000_LDOGCTL, 0, 1);
return 0;
}
-#endif
static iomux_v3_cfg_t const uart1_pads[] = {
MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
@@ -299,10 +184,6 @@ int board_init(void)
gpio_request(IMX_GPIO_NR(4, 16), "ncp692");
gpio_direction_output(IMX_GPIO_NR(4, 16) , 1);
-#ifdef CONFIG_SYS_I2C_MXC
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
-#endif
-
setup_fec();
return 0;
diff --git a/configs/udoo_neo_defconfig b/configs/udoo_neo_defconfig
index ca08de1bd4..9177bdba65 100644
--- a/configs/udoo_neo_defconfig
+++ b/configs/udoo_neo_defconfig
@@ -10,8 +10,9 @@ CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0x80000
CONFIG_MX6SX=y
CONFIG_TARGET_UDOO_NEO=y
-CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_DM_I2C=y
CONFIG_DM_GPIO=y
+CONFIG_DM_MMC=y
CONFIG_DEFAULT_DEVICE_TREE="imx6sx-udoo-neo-basic"
CONFIG_SPL_TEXT_BASE=0x00908000
CONFIG_SPL_MMC=y
@@ -39,8 +40,6 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_BOUNCE_BUFFER=y
-CONFIG_SYS_I2C_LEGACY=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MXC=y
CONFIG_FSL_USDHC=y
CONFIG_PHYLIB=y
@@ -52,11 +51,12 @@ CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
-CONFIG_POWER_LEGACY=y
-CONFIG_POWER_I2C=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_ANATOP=y
CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_PFUZE100=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
diff --git a/include/configs/udoo_neo.h b/include/configs/udoo_neo.h
index 3a7cb050b1..ac13c3e57f 100644
--- a/include/configs/udoo_neo.h
+++ b/include/configs/udoo_neo.h
@@ -68,9 +68,4 @@
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-/* PMIC */
-#define CONFIG_POWER_PFUZE3000
-#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
-#define PFUZE3000_I2C_BUS 0
-
#endif /* __CONFIG_H */
--
2.33.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] udoo_neo: Move to DM for REGUALTOR/PMIC/I2C drivers
2021-12-22 0:17 [PATCH] udoo_neo: Move to DM for REGUALTOR/PMIC/I2C drivers Peter Robinson
@ 2021-12-22 0:38 ` Fabio Estevam
2022-02-18 19:28 ` Stefano Babic
0 siblings, 1 reply; 3+ messages in thread
From: Fabio Estevam @ 2021-12-22 0:38 UTC (permalink / raw)
To: Peter Robinson; +Cc: Breno Lima, Francesco Montefoschi, U-Boot-Denx
Hi Peter,
On Tue, Dec 21, 2021 at 9:17 PM Peter Robinson <pbrobinson@gmail.com> wrote:
>
> This moves over the PMIC power init to DM and the associated i2c and
> regulator bits.
>
> Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
> ---
> board/udoo/neo/neo.c | 139 +++----------------------------------
> configs/udoo_neo_defconfig | 10 +--
> include/configs/udoo_neo.h | 5 --
> 3 files changed, 15 insertions(+), 139 deletions(-)
Nice diff ;-)
Reviewed-by: Fabio Estevam <festevam@gmail.com>
>
> diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c
> index 62f81fff68..d374b86b5d 100644
> --- a/board/udoo/neo/neo.c
> +++ b/board/udoo/neo/neo.c
> @@ -51,11 +51,6 @@ enum {
> PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
> PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
>
> -#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
> - PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
> - PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
> - PAD_CTL_ODE)
> -
> #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
> PAD_CTL_SPEED_MED | \
> PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
> @@ -81,135 +76,25 @@ int dram_init(void)
> return 0;
> }
>
> -#ifdef CONFIG_SYS_I2C_MXC
> -#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
> -/* I2C1 for PMIC */
> -static struct i2c_pads_info i2c_pad_info1 = {
> - .scl = {
> - .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
> - .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
> - .gp = IMX_GPIO_NR(1, 0),
> - },
> - .sda = {
> - .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
> - .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
> - .gp = IMX_GPIO_NR(1, 1),
> - },
> -};
> -#endif
> -
> -#if CONFIG_IS_ENABLED(POWER_LEGACY)
> int power_init_board(void)
> {
> - struct pmic *p;
> - int ret;
> - unsigned int reg, rev_id;
> -
> - ret = power_pfuze3000_init(PFUZE3000_I2C_BUS);
> - if (ret)
> - return ret;
> -
> - p = pmic_get("PFUZE3000");
> - ret = pmic_probe(p);
> - if (ret)
> - return ret;
> + struct udevice *dev;
> + int ret, dev_id, rev_id;
>
> - pmic_reg_read(p, PFUZE3000_DEVICEID, ®);
> - pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
> - printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
> -
> - /* disable Low Power Mode during standby mode */
> - pmic_reg_read(p, PFUZE3000_LDOGCTL, ®);
> - reg |= 0x1;
> - ret = pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
> - if (ret)
> + ret = pmic_get("pfuze3000@8", &dev);
> + if (ret == -ENODEV)
> + return 0;
> + if (ret != 0)
> return ret;
>
> - ret = pmic_reg_write(p, PFUZE3000_SW1AMODE, 0xc);
> - if (ret)
> - return ret;
> + dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
> + rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
> + printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
>
> - ret = pmic_reg_write(p, PFUZE3000_SW1BMODE, 0xc);
> - if (ret)
> - return ret;
> -
> - ret = pmic_reg_write(p, PFUZE3000_SW2MODE, 0xc);
> - if (ret)
> - return ret;
> -
> - ret = pmic_reg_write(p, PFUZE3000_SW3MODE, 0xc);
> - if (ret)
> - return ret;
> -
> - /* set SW1A standby voltage 0.975V */
> - pmic_reg_read(p, PFUZE3000_SW1ASTBY, ®);
> - reg &= ~0x3f;
> - reg |= PFUZE3000_SW1AB_SETP(9750);
> - ret = pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg);
> - if (ret)
> - return ret;
> -
> - /* set SW1B standby voltage 0.975V */
> - pmic_reg_read(p, PFUZE3000_SW1BSTBY, ®);
> - reg &= ~0x3f;
> - reg |= PFUZE3000_SW1AB_SETP(9750);
> - ret = pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg);
> - if (ret)
> - return ret;
> -
> - /* set SW1A/VDD_ARM_IN step ramp up time from 16us to 4us/25mV */
> - pmic_reg_read(p, PFUZE3000_SW1ACONF, ®);
> - reg &= ~0xc0;
> - reg |= 0x40;
> - ret = pmic_reg_write(p, PFUZE3000_SW1ACONF, reg);
> - if (ret)
> - return ret;
> -
> - /* set SW1B/VDD_SOC_IN step ramp up time from 16us to 4us/25mV */
> - pmic_reg_read(p, PFUZE3000_SW1BCONF, ®);
> - reg &= ~0xc0;
> - reg |= 0x40;
> - ret = pmic_reg_write(p, PFUZE3000_SW1BCONF, reg);
> - if (ret)
> - return ret;
> -
> - /* set VDD_ARM_IN to 1.350V */
> - pmic_reg_read(p, PFUZE3000_SW1AVOLT, ®);
> - reg &= ~0x3f;
> - reg |= PFUZE3000_SW1AB_SETP(13500);
> - ret = pmic_reg_write(p, PFUZE3000_SW1AVOLT, reg);
> - if (ret)
> - return ret;
> -
> - /* set VDD_SOC_IN to 1.350V */
> - pmic_reg_read(p, PFUZE3000_SW1BVOLT, ®);
> - reg &= ~0x3f;
> - reg |= PFUZE3000_SW1AB_SETP(13500);
> - ret = pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg);
> - if (ret)
> - return ret;
> -
> - /* set DDR_1_5V to 1.350V */
> - pmic_reg_read(p, PFUZE3000_SW3VOLT, ®);
> - reg &= ~0x0f;
> - reg |= PFUZE3000_SW3_SETP(13500);
> - ret = pmic_reg_write(p, PFUZE3000_SW3VOLT, reg);
> - if (ret)
> - return ret;
> -
> - /* set VGEN2_1V5 to 1.5V */
> - pmic_reg_read(p, PFUZE3000_VLDO2CTL, ®);
> - reg &= ~0x0f;
> - reg |= PFUZE3000_VLDO_SETP(15000);
> - /* enable */
> - reg |= 0x10;
> - ret = pmic_reg_write(p, PFUZE3000_VLDO2CTL, reg);
> - if (ret)
> - return ret;
> + pmic_clrsetbits(dev, PFUZE3000_LDOGCTL, 0, 1);
>
> return 0;
> }
> -#endif
>
> static iomux_v3_cfg_t const uart1_pads[] = {
> MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
> @@ -299,10 +184,6 @@ int board_init(void)
> gpio_request(IMX_GPIO_NR(4, 16), "ncp692");
> gpio_direction_output(IMX_GPIO_NR(4, 16) , 1);
>
> -#ifdef CONFIG_SYS_I2C_MXC
> - setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
> -#endif
> -
> setup_fec();
>
> return 0;
> diff --git a/configs/udoo_neo_defconfig b/configs/udoo_neo_defconfig
> index ca08de1bd4..9177bdba65 100644
> --- a/configs/udoo_neo_defconfig
> +++ b/configs/udoo_neo_defconfig
> @@ -10,8 +10,9 @@ CONFIG_ENV_SIZE=0x2000
> CONFIG_ENV_OFFSET=0x80000
> CONFIG_MX6SX=y
> CONFIG_TARGET_UDOO_NEO=y
> -CONFIG_SYS_I2C_MXC_I2C1=y
> +CONFIG_DM_I2C=y
> CONFIG_DM_GPIO=y
> +CONFIG_DM_MMC=y
> CONFIG_DEFAULT_DEVICE_TREE="imx6sx-udoo-neo-basic"
> CONFIG_SPL_TEXT_BASE=0x00908000
> CONFIG_SPL_MMC=y
> @@ -39,8 +40,6 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> CONFIG_SYS_MMC_ENV_DEV=1
> CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
> CONFIG_BOUNCE_BUFFER=y
> -CONFIG_SYS_I2C_LEGACY=y
> -CONFIG_SPL_SYS_I2C_LEGACY=y
> CONFIG_SYS_I2C_MXC=y
> CONFIG_FSL_USDHC=y
> CONFIG_PHYLIB=y
> @@ -52,11 +51,12 @@ CONFIG_FEC_MXC=y
> CONFIG_MII=y
> CONFIG_PINCTRL=y
> CONFIG_PINCTRL_IMX6=y
> -CONFIG_POWER_LEGACY=y
> -CONFIG_POWER_I2C=y
> +CONFIG_DM_PMIC=y
> +CONFIG_DM_PMIC_PFUZE100=y
> CONFIG_DM_REGULATOR=y
> CONFIG_DM_REGULATOR_ANATOP=y
> CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_REGULATOR_PFUZE100=y
> CONFIG_USB=y
> CONFIG_DM_USB=y
> CONFIG_USB_STORAGE=y
> diff --git a/include/configs/udoo_neo.h b/include/configs/udoo_neo.h
> index 3a7cb050b1..ac13c3e57f 100644
> --- a/include/configs/udoo_neo.h
> +++ b/include/configs/udoo_neo.h
> @@ -68,9 +68,4 @@
> #define CONFIG_SYS_INIT_SP_ADDR \
> (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
>
> -/* PMIC */
> -#define CONFIG_POWER_PFUZE3000
> -#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
> -#define PFUZE3000_I2C_BUS 0
> -
> #endif /* __CONFIG_H */
> --
> 2.33.1
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] udoo_neo: Move to DM for REGUALTOR/PMIC/I2C drivers
2021-12-22 0:38 ` Fabio Estevam
@ 2022-02-18 19:28 ` Stefano Babic
0 siblings, 0 replies; 3+ messages in thread
From: Stefano Babic @ 2022-02-18 19:28 UTC (permalink / raw)
To: Fabio Estevam, Peter Robinson
Cc: Breno Lima, Francesco Montefoschi, U-Boot-Denx
hi Peter,
On 22.12.21 01:38, Fabio Estevam wrote:
> Hi Peter,
>
> On Tue, Dec 21, 2021 at 9:17 PM Peter Robinson <pbrobinson@gmail.com> wrote:
>>
>> This moves over the PMIC power init to DM and the associated i2c and
>> regulator bits.
>>
>> Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
>> ---
>> board/udoo/neo/neo.c | 139 +++----------------------------------
>> configs/udoo_neo_defconfig | 10 +--
>> include/configs/udoo_neo.h | 5 --
>> 3 files changed, 15 insertions(+), 139 deletions(-)
>
> Nice diff ;-)
>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
>
I get warning after applying the patch:
board/udoo/neo/neo.c:86:15: error: implicit declaration of function
'pmic_get' [-Werror=implicit-function-declaration]
+ 86 | ret = pmic_get("pfuze3000@8", &dev);
+ | ^~~~~~~~
+board/udoo/neo/neo.c:92:18: error: implicit declaration of function
'pmic_reg_read'; did you mean 'dm_i2c_reg_read'?
[-Werror=implicit-function-declaration]
+ 92 | dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
+ | ^~~~~~~~~~~~~
+ | dm_i2c_reg_read
+board/udoo/neo/neo.c:96:9: error: implicit declaration of function
'pmic_clrsetbits'; did you mean 'clrsetbits'?
[-Werror=implicit-function-declaration]
+ 96 | pmic_clrsetbits(dev, PFUZE3000_LDOGCTL, 0, 1);
+ | ^~~~~~~~~~~~~~~
+ | clrsetbits
+cc1: all warnings being treated as errors
+make[2]: *** [scripts/Makefile.build:254: board/udoo/neo/neo.o] Error 1
+make[1]: *** [Makefile:1890: board/udoo/neo] Error 2
Can you check and repost ?
Thanks !
Best regards,
Stefano
>
>
>>
>> diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c
>> index 62f81fff68..d374b86b5d 100644
>> --- a/board/udoo/neo/neo.c
>> +++ b/board/udoo/neo/neo.c
>> @@ -51,11 +51,6 @@ enum {
>> PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
>> PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
>>
>> -#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
>> - PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
>> - PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
>> - PAD_CTL_ODE)
>> -
>> #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
>> PAD_CTL_SPEED_MED | \
>> PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
>> @@ -81,135 +76,25 @@ int dram_init(void)
>> return 0;
>> }
>>
>> -#ifdef CONFIG_SYS_I2C_MXC
>> -#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
>> -/* I2C1 for PMIC */
>> -static struct i2c_pads_info i2c_pad_info1 = {
>> - .scl = {
>> - .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
>> - .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
>> - .gp = IMX_GPIO_NR(1, 0),
>> - },
>> - .sda = {
>> - .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
>> - .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
>> - .gp = IMX_GPIO_NR(1, 1),
>> - },
>> -};
>> -#endif
>> -
>> -#if CONFIG_IS_ENABLED(POWER_LEGACY)
>> int power_init_board(void)
>> {
>> - struct pmic *p;
>> - int ret;
>> - unsigned int reg, rev_id;
>> -
>> - ret = power_pfuze3000_init(PFUZE3000_I2C_BUS);
>> - if (ret)
>> - return ret;
>> -
>> - p = pmic_get("PFUZE3000");
>> - ret = pmic_probe(p);
>> - if (ret)
>> - return ret;
>> + struct udevice *dev;
>> + int ret, dev_id, rev_id;
>>
>> - pmic_reg_read(p, PFUZE3000_DEVICEID, ®);
>> - pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
>> - printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
>> -
>> - /* disable Low Power Mode during standby mode */
>> - pmic_reg_read(p, PFUZE3000_LDOGCTL, ®);
>> - reg |= 0x1;
>> - ret = pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
>> - if (ret)
>> + ret = pmic_get("pfuze3000@8", &dev);
>> + if (ret == -ENODEV)
>> + return 0;
>> + if (ret != 0)
>> return ret;
>>
>> - ret = pmic_reg_write(p, PFUZE3000_SW1AMODE, 0xc);
>> - if (ret)
>> - return ret;
>> + dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
>> + rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
>> + printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
>>
>> - ret = pmic_reg_write(p, PFUZE3000_SW1BMODE, 0xc);
>> - if (ret)
>> - return ret;
>> -
>> - ret = pmic_reg_write(p, PFUZE3000_SW2MODE, 0xc);
>> - if (ret)
>> - return ret;
>> -
>> - ret = pmic_reg_write(p, PFUZE3000_SW3MODE, 0xc);
>> - if (ret)
>> - return ret;
>> -
>> - /* set SW1A standby voltage 0.975V */
>> - pmic_reg_read(p, PFUZE3000_SW1ASTBY, ®);
>> - reg &= ~0x3f;
>> - reg |= PFUZE3000_SW1AB_SETP(9750);
>> - ret = pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg);
>> - if (ret)
>> - return ret;
>> -
>> - /* set SW1B standby voltage 0.975V */
>> - pmic_reg_read(p, PFUZE3000_SW1BSTBY, ®);
>> - reg &= ~0x3f;
>> - reg |= PFUZE3000_SW1AB_SETP(9750);
>> - ret = pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg);
>> - if (ret)
>> - return ret;
>> -
>> - /* set SW1A/VDD_ARM_IN step ramp up time from 16us to 4us/25mV */
>> - pmic_reg_read(p, PFUZE3000_SW1ACONF, ®);
>> - reg &= ~0xc0;
>> - reg |= 0x40;
>> - ret = pmic_reg_write(p, PFUZE3000_SW1ACONF, reg);
>> - if (ret)
>> - return ret;
>> -
>> - /* set SW1B/VDD_SOC_IN step ramp up time from 16us to 4us/25mV */
>> - pmic_reg_read(p, PFUZE3000_SW1BCONF, ®);
>> - reg &= ~0xc0;
>> - reg |= 0x40;
>> - ret = pmic_reg_write(p, PFUZE3000_SW1BCONF, reg);
>> - if (ret)
>> - return ret;
>> -
>> - /* set VDD_ARM_IN to 1.350V */
>> - pmic_reg_read(p, PFUZE3000_SW1AVOLT, ®);
>> - reg &= ~0x3f;
>> - reg |= PFUZE3000_SW1AB_SETP(13500);
>> - ret = pmic_reg_write(p, PFUZE3000_SW1AVOLT, reg);
>> - if (ret)
>> - return ret;
>> -
>> - /* set VDD_SOC_IN to 1.350V */
>> - pmic_reg_read(p, PFUZE3000_SW1BVOLT, ®);
>> - reg &= ~0x3f;
>> - reg |= PFUZE3000_SW1AB_SETP(13500);
>> - ret = pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg);
>> - if (ret)
>> - return ret;
>> -
>> - /* set DDR_1_5V to 1.350V */
>> - pmic_reg_read(p, PFUZE3000_SW3VOLT, ®);
>> - reg &= ~0x0f;
>> - reg |= PFUZE3000_SW3_SETP(13500);
>> - ret = pmic_reg_write(p, PFUZE3000_SW3VOLT, reg);
>> - if (ret)
>> - return ret;
>> -
>> - /* set VGEN2_1V5 to 1.5V */
>> - pmic_reg_read(p, PFUZE3000_VLDO2CTL, ®);
>> - reg &= ~0x0f;
>> - reg |= PFUZE3000_VLDO_SETP(15000);
>> - /* enable */
>> - reg |= 0x10;
>> - ret = pmic_reg_write(p, PFUZE3000_VLDO2CTL, reg);
>> - if (ret)
>> - return ret;
>> + pmic_clrsetbits(dev, PFUZE3000_LDOGCTL, 0, 1);
>>
>> return 0;
>> }
>> -#endif
>>
>> static iomux_v3_cfg_t const uart1_pads[] = {
>> MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
>> @@ -299,10 +184,6 @@ int board_init(void)
>> gpio_request(IMX_GPIO_NR(4, 16), "ncp692");
>> gpio_direction_output(IMX_GPIO_NR(4, 16) , 1);
>>
>> -#ifdef CONFIG_SYS_I2C_MXC
>> - setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
>> -#endif
>> -
>> setup_fec();
>>
>> return 0;
>> diff --git a/configs/udoo_neo_defconfig b/configs/udoo_neo_defconfig
>> index ca08de1bd4..9177bdba65 100644
>> --- a/configs/udoo_neo_defconfig
>> +++ b/configs/udoo_neo_defconfig
>> @@ -10,8 +10,9 @@ CONFIG_ENV_SIZE=0x2000
>> CONFIG_ENV_OFFSET=0x80000
>> CONFIG_MX6SX=y
>> CONFIG_TARGET_UDOO_NEO=y
>> -CONFIG_SYS_I2C_MXC_I2C1=y
>> +CONFIG_DM_I2C=y
>> CONFIG_DM_GPIO=y
>> +CONFIG_DM_MMC=y
>> CONFIG_DEFAULT_DEVICE_TREE="imx6sx-udoo-neo-basic"
>> CONFIG_SPL_TEXT_BASE=0x00908000
>> CONFIG_SPL_MMC=y
>> @@ -39,8 +40,6 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
>> CONFIG_SYS_MMC_ENV_DEV=1
>> CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
>> CONFIG_BOUNCE_BUFFER=y
>> -CONFIG_SYS_I2C_LEGACY=y
>> -CONFIG_SPL_SYS_I2C_LEGACY=y
>> CONFIG_SYS_I2C_MXC=y
>> CONFIG_FSL_USDHC=y
>> CONFIG_PHYLIB=y
>> @@ -52,11 +51,12 @@ CONFIG_FEC_MXC=y
>> CONFIG_MII=y
>> CONFIG_PINCTRL=y
>> CONFIG_PINCTRL_IMX6=y
>> -CONFIG_POWER_LEGACY=y
>> -CONFIG_POWER_I2C=y
>> +CONFIG_DM_PMIC=y
>> +CONFIG_DM_PMIC_PFUZE100=y
>> CONFIG_DM_REGULATOR=y
>> CONFIG_DM_REGULATOR_ANATOP=y
>> CONFIG_DM_REGULATOR_FIXED=y
>> +CONFIG_DM_REGULATOR_PFUZE100=y
>> CONFIG_USB=y
>> CONFIG_DM_USB=y
>> CONFIG_USB_STORAGE=y
>> diff --git a/include/configs/udoo_neo.h b/include/configs/udoo_neo.h
>> index 3a7cb050b1..ac13c3e57f 100644
>> --- a/include/configs/udoo_neo.h
>> +++ b/include/configs/udoo_neo.h
>> @@ -68,9 +68,4 @@
>> #define CONFIG_SYS_INIT_SP_ADDR \
>> (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
>>
>> -/* PMIC */
>> -#define CONFIG_POWER_PFUZE3000
>> -#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
>> -#define PFUZE3000_I2C_BUS 0
>> -
>> #endif /* __CONFIG_H */
>> --
>> 2.33.1
>>
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2022-02-18 19:29 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-12-22 0:17 [PATCH] udoo_neo: Move to DM for REGUALTOR/PMIC/I2C drivers Peter Robinson
2021-12-22 0:38 ` Fabio Estevam
2022-02-18 19:28 ` Stefano Babic
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.