[U-Boot] No prompt on mx25pdk boot

[U-Boot] No prompt on mx25pdk boot

[Hugo Holgersson]

Dear readers,

I have problems running U-Boot on my i.MX 25 PDK board. 

I have tried two methods:

(A)
git clone git://www.denx.de/git/u-boot-imx.git master
nano board/freescale/mx25pdk/imximage.cfg  # change to BOOT_FROM nand
make CROSS_COMPILE=arm-none-linux-gnueabi- mx25pdk_config 
make CROSS_COMPILE=arm-none-linux-gnueabi- u-boot.imx

The u-boot.imx is flashed using FreeScale AVK to address 0x400 in NAND. This image does not work (no UART output).

My question is obviously if the my image is found and executed at all and first of all if all headers are set up correctly. By comparing the 2009.08 u-boot.bin from FreeScale's LTIB (that runs and gives me a prompt) with the new u-boot.imx, I found out that the old u-boot.bin puts a branch to the "reset"-routine...

00000000 <.data>:
       0:       ea00016a        b       0x5b0
        ...
     400:       83f005b0      
     404:       000000b1   
     408:       00000000      
     40c:       83f00414       
     410:       00000000        
     414:       83f0041c    

... at top of NAND. Whereas the new u-boot.imx image does not:

00000000 <.data>:
       0:       81200000    
       4:       000000b1     
       8:       00000000      
       c:       811ffc14     
      10:       00000000       
      14:       811ffc1c       

This is the main difference I can found while comparing the old working, 2009.08 u-boot.bin to the one generated with "make u-boot.imx". 

Note 1: The flash header starts at 0x400 in both cases, since the .imx is flashed to 0x400 and the .bin is flashed to 0x0 in NAND.
Note 2: The addresses pointed out are different because TEXT_BASE was set up differently. RAM is 0x8......

(B)
I tried to manually add the headers used in u-boot 2009.08, directly to the new u-boot.bin, instead of using the imximage tool, by modifying linkage:

I added dcdheader.S to arch/arm/cpu/arm926ejs/mx25/dcdheader.S
and the information about dcdheader.o to:
- arch/arm/cpu/arm926ejs/u-boot.lds
- arch/arm/cpu/arm926ejs/mx25/Makefile

(patch available)

These modifications gave a u-boot.bin with headers having the same layout as those in 2009.08 u-boot.bin (the branch to reset at address 0x00000000 also included). No luck. 

For now the only way of debugging is the board's UART log since I haven?t managed to hook up my Segger J-Link... Any ideas are welcome! 

Best regards,

Hugo Holgersson

[U-Boot] No prompt on mx25pdk boot

[Fabio Estevam]

Hi Hugo,

On Thu, Oct 20, 2011 at 2:04 PM, Hugo Holgersson
<hugoh@student.chalmers.se> wrote:
> Dear readers,
>
> I have problems running U-Boot on my i.MX 25 PDK board.
>
> I have tried two methods:
>
> (A)
> git clone git://www.denx.de/git/u-boot-imx.git master
> nano board/freescale/mx25pdk/imximage.cfg ?# change to BOOT_FROM nand
> make CROSS_COMPILE=arm-none-linux-gnueabi- mx25pdk_config
> make CROSS_COMPILE=arm-none-linux-gnueabi- u-boot.imx
>
> The u-boot.imx is flashed using FreeScale AVK to address 0x400 in NAND. This image does not work (no UART output).

I have only tested booting MX25PDK from the SD card. Does this method
work for you?

Regards,

Fabio Estevam

[U-Boot] No prompt on mx25pdk boot

[Hugo Holgersson]

Hi Fabio!

No I have not, I need to find one SD card. 

Meanwhile, do you have any tips and tricks to aid the debugging on this board? 

For example, can the JTAG-connector of the debug board serve me anyhow? 
Unfortunately, I do not own the Abatron BDI2000 device, I only got the Segger J-Link.

By the way, do you develop within CodeWarrior or any other IDE? 

Regards,

Hugo Holgersson


________________________________________
Fr?n: Fabio Estevam [festevam at gmail.com]
Skickat: den 20 oktober 2011 18:19

Hi Hugo,

On Thu, Oct 20, 2011 at 2:04 PM, Hugo Holgersson
<hugoh@student.chalmers.se> wrote:
> Dear readers,
>
> I have problems running U-Boot on my i.MX 25 PDK board.
>
> I have tried two methods:
>
> (A)
> git clone git://www.denx.de/git/u-boot-imx.git master
> nano board/freescale/mx25pdk/imximage.cfg  # change to BOOT_FROM nand
> make CROSS_COMPILE=arm-none-linux-gnueabi- mx25pdk_config
> make CROSS_COMPILE=arm-none-linux-gnueabi- u-boot.imx
>
> The u-boot.imx is flashed using FreeScale AVK to address 0x400 in NAND. This image does not work (no UART output).

I have only tested booting MX25PDK from the SD card. Does this method
work for you?

Regards,

Fabio Estevam

[U-Boot] No prompt on mx25pdk boot

[Fabio Estevam]

On Thu, Oct 20, 2011 at 2:42 PM, Hugo Holgersson
<hugoh@student.chalmers.se> wrote:
> Hi Fabio!
>
> No I have not, I need to find one SD card.

For flashing the SD card with u-boot.imx you can follow
doc/README.imximage file.

> Meanwhile, do you have any tips and tricks to aid the debugging on this board?
>
> For example, can the JTAG-connector of the debug board serve me anyhow?
> Unfortunately, I do not own the Abatron BDI2000 device, I only got the Segger J-Link.

Segger J-link is supported by OpenOCD project. Take a look on this
project and if you have issues you can then post at the OpenOCD
mailing list.

> By the way, do you develop within CodeWarrior or any other IDE?

No CodeWarrior nor any other IDE here, but this is more a matter of taste ;-)

Regards,

Fabio Estevam