[PATCH v3 1/4] dt-bindings: arm: fsl: Add binding for Variscite VAR-SOM-MX8MM module

[PATCH v3 1/4] dt-bindings: arm: fsl: Add binding for Variscite VAR-SOM-MX8MM module

[Krzysztof Kozlowski]

Add a binding for the Variscite VAR-SOM-MX8MM System on Module.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Based on top of:
https://lore.kernel.org/linux-arm-kernel/20200823172019.18606-1-krzk@kernel.org/

Changes since v1:
1. None
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index b48dbf924cfe..39f3a3d5f524 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -346,6 +346,7 @@ properties:
           - enum:
               - beacon,imx8mm-beacon-kit  # i.MX8MM Beacon Development Kit
               - fsl,imx8mm-evk            # i.MX8MM EVK Board
+              - variscite,var-som-mx8mm   # i.MX8MM Variscite VAR-SOM-MX8MM module
           - const: fsl,imx8mm
 
       - description: i.MX8MN based Boards
-- 
2.17.1

[PATCH v3 1/4] dt-bindings: arm: fsl: Add binding for Variscite VAR-SOM-MX8MM module

[Krzysztof Kozlowski]

Add a binding for the Variscite VAR-SOM-MX8MM System on Module.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Based on top of:
https://lore.kernel.org/linux-arm-kernel/20200823172019.18606-1-krzk@kernel.org/

Changes since v1:
1. None
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index b48dbf924cfe..39f3a3d5f524 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -346,6 +346,7 @@ properties:
           - enum:
               - beacon,imx8mm-beacon-kit  # i.MX8MM Beacon Development Kit
               - fsl,imx8mm-evk            # i.MX8MM EVK Board
+              - variscite,var-som-mx8mm   # i.MX8MM Variscite VAR-SOM-MX8MM module
           - const: fsl,imx8mm
 
       - description: i.MX8MN based Boards
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 2/4] dt-bindings: arm: fsl: Add binding for Variscite Symphony board with VAR-SOM-MX8MM

[Krzysztof Kozlowski]

Add a binding for the Variscite Symphony evaluation kit board with
VAR-SOM-MX8MM System on Module.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v1:
1. None
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 39f3a3d5f524..b378297c390a 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -349,6 +349,12 @@ properties:
               - variscite,var-som-mx8mm   # i.MX8MM Variscite VAR-SOM-MX8MM module
           - const: fsl,imx8mm
 
+      - description: Variscite VAR-SOM-MX8MM based boards
+        items:
+          - const: variscite,var-som-mx8mm-symphony
+          - const: variscite,var-som-mx8mm
+          - const: fsl,imx8mm
+
       - description: i.MX8MN based Boards
         items:
           - enum:
-- 
2.17.1

[PATCH v3 2/4] dt-bindings: arm: fsl: Add binding for Variscite Symphony board with VAR-SOM-MX8MM

[Krzysztof Kozlowski]

Add a binding for the Variscite Symphony evaluation kit board with
VAR-SOM-MX8MM System on Module.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v1:
1. None
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 39f3a3d5f524..b378297c390a 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -349,6 +349,12 @@ properties:
               - variscite,var-som-mx8mm   # i.MX8MM Variscite VAR-SOM-MX8MM module
           - const: fsl,imx8mm
 
+      - description: Variscite VAR-SOM-MX8MM based boards
+        items:
+          - const: variscite,var-som-mx8mm-symphony
+          - const: variscite,var-som-mx8mm
+          - const: fsl,imx8mm
+
       - description: i.MX8MN based Boards
         items:
           - enum:
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Krzysztof Kozlowski]

Add DTSI of Variscite VAR-SOM-MX8MM System on Module in a basic version,
delivered with Variscite Symphony Evaluation kit.  This version comes
with:
 - 2 GB of RAM,
 - 16 GB eMMC,
 - Gigabit Ethernet PHY,
 - 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth (Cypress CYW43353),
 - CAN bus,
 - Audio codec (not yet configured in DTSI).

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v2:
1. Remove fsl,spi-num-chipselects,
2. Remove can node (not yet in mainline),
3. Use phy properties instead of deprecated phy-reset-xxx,
4. Remove orphaned pinctrl-names,
5. Use lowercase regulator names to match schema,
6. Use more specific regulator node names.

Changes since v1:
1. None
---
 .../boot/dts/freescale/imx8mm-var-som.dtsi    | 559 ++++++++++++++++++
 1 file changed, 559 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
new file mode 100644
index 000000000000..a651a4a36748
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
@@ -0,0 +1,559 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ * Copyright (C) 2020 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Variscite VAR-SOM-MX8MM module";
+	compatible = "variscite,var-som-mx8mm", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	reg_eth_phy: regulator-eth-phy {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_eth_phy>;
+		regulator-name = "eth_phy_pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>,
+		   <&gpio1  0 GPIO_ACTIVE_HIGH>;
+	/delete-property/ dmas;
+	/delete-property/ dma-names;
+	status = "okay";
+
+	/* Resistive touch controller */
+	touchscreen@0 {
+		reg = <0>;
+		compatible = "ti,ads7846";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_restouch>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+
+		spi-max-frequency = <1500000>;
+		pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+
+		ti,x-min = /bits/ 16 <125>;
+		touchscreen-size-x = /bits/ 16 <4008>;
+		ti,y-min = /bits/ 16 <282>;
+		touchscreen-size-y = /bits/ 16 <3864>;
+		ti,x-plate-ohms = /bits/ 16 <180>;
+		touchscreen-max-pressure = /bits/ 16 <255>;
+		touchscreen-average-samples = /bits/ 16 <10>;
+		ti,debounce-tol = /bits/ 16 <3>;
+		ti,debounce-rep = /bits/ 16 <1>;
+		ti,settle-delay-usec = /bits/ 16 <150>;
+		ti,keep-vref-on;
+		wakeup-source;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
+	phy-supply = <&reg_eth_phy>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@4 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <4>;
+			reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <8 GPIO_ACTIVE_LOW>;
+		rohm,reset-snvs-powered;
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <900000>;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "buck6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-compatible = "ldo5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	/* TODO: configure audio, as of now just put a placeholder */
+	wm8904: codec@1a {
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+		status = "disabled";
+	};
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* Bluetooth */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* Console */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	usb-role-switch;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "otg";
+	usb-role-switch;
+	status = "okay";
+};
+
+/* WIFI */
+&usdhc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <4>;
+	non-removable;
+	keep-power-in-suspend;
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SD */
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
+	assigned-clock-rates = <200000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x13
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x13
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x13
+			MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x13
+			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x13
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x41
+		>;
+	};
+
+	pinctrl_pmic: pmicirq {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8	0x41
+		>;
+	};
+
+	pinctrl_reg_eth_phy: regethphygrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9	0x41
+		>;
+	};
+
+	pinctrl_restouch: restouchgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x1c0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX	0x140
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX	0x140
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B	0x140
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B	0x140
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX	0x140
+			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x190
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d0
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0	0x1d0
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1	0x1d0
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2	0x1d0
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x194
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d4
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0	0x1d4
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1	0x1d4
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2	0x1d4
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3	0x1d4
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x196
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d6
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0	0x1d6
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1	0x1d6
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2	0x1d6
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3	0x1d6
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0xc1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d6
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x190
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d0
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d0
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d0
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d0
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d0
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d0
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d0
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d0
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d0
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x194
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d4
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d4
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x196
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d6
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d6
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d6
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d6
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d6
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d6
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d6
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d6
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d6
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6
+		>;
+	};
+};
-- 
2.17.1

[PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Krzysztof Kozlowski]

Add DTSI of Variscite VAR-SOM-MX8MM System on Module in a basic version,
delivered with Variscite Symphony Evaluation kit.  This version comes
with:
 - 2 GB of RAM,
 - 16 GB eMMC,
 - Gigabit Ethernet PHY,
 - 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth (Cypress CYW43353),
 - CAN bus,
 - Audio codec (not yet configured in DTSI).

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v2:
1. Remove fsl,spi-num-chipselects,
2. Remove can node (not yet in mainline),
3. Use phy properties instead of deprecated phy-reset-xxx,
4. Remove orphaned pinctrl-names,
5. Use lowercase regulator names to match schema,
6. Use more specific regulator node names.

Changes since v1:
1. None
---
 .../boot/dts/freescale/imx8mm-var-som.dtsi    | 559 ++++++++++++++++++
 1 file changed, 559 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
new file mode 100644
index 000000000000..a651a4a36748
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
@@ -0,0 +1,559 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ * Copyright (C) 2020 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Variscite VAR-SOM-MX8MM module";
+	compatible = "variscite,var-som-mx8mm", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	reg_eth_phy: regulator-eth-phy {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_eth_phy>;
+		regulator-name = "eth_phy_pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>,
+		   <&gpio1  0 GPIO_ACTIVE_HIGH>;
+	/delete-property/ dmas;
+	/delete-property/ dma-names;
+	status = "okay";
+
+	/* Resistive touch controller */
+	touchscreen@0 {
+		reg = <0>;
+		compatible = "ti,ads7846";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_restouch>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+
+		spi-max-frequency = <1500000>;
+		pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+
+		ti,x-min = /bits/ 16 <125>;
+		touchscreen-size-x = /bits/ 16 <4008>;
+		ti,y-min = /bits/ 16 <282>;
+		touchscreen-size-y = /bits/ 16 <3864>;
+		ti,x-plate-ohms = /bits/ 16 <180>;
+		touchscreen-max-pressure = /bits/ 16 <255>;
+		touchscreen-average-samples = /bits/ 16 <10>;
+		ti,debounce-tol = /bits/ 16 <3>;
+		ti,debounce-rep = /bits/ 16 <1>;
+		ti,settle-delay-usec = /bits/ 16 <150>;
+		ti,keep-vref-on;
+		wakeup-source;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
+	phy-supply = <&reg_eth_phy>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@4 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <4>;
+			reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <8 GPIO_ACTIVE_LOW>;
+		rohm,reset-snvs-powered;
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <900000>;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "buck6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-compatible = "ldo5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	/* TODO: configure audio, as of now just put a placeholder */
+	wm8904: codec@1a {
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+		status = "disabled";
+	};
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* Bluetooth */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* Console */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	usb-role-switch;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "otg";
+	usb-role-switch;
+	status = "okay";
+};
+
+/* WIFI */
+&usdhc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <4>;
+	non-removable;
+	keep-power-in-suspend;
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SD */
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
+	assigned-clock-rates = <200000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x13
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x13
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x13
+			MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x13
+			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x13
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x41
+		>;
+	};
+
+	pinctrl_pmic: pmicirq {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8	0x41
+		>;
+	};
+
+	pinctrl_reg_eth_phy: regethphygrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9	0x41
+		>;
+	};
+
+	pinctrl_restouch: restouchgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x1c0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX	0x140
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX	0x140
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B	0x140
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B	0x140
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX	0x140
+			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x190
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d0
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0	0x1d0
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1	0x1d0
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2	0x1d0
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x194
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d4
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0	0x1d4
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1	0x1d4
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2	0x1d4
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3	0x1d4
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x196
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d6
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0	0x1d6
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1	0x1d6
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2	0x1d6
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3	0x1d6
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0xc1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d6
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x190
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d0
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d0
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d0
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d0
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d0
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d0
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d0
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d0
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d0
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x194
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d4
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d4
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x196
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d6
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d6
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d6
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d6
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d6
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d6
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d6
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d6
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d6
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6
+		>;
+	};
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 4/4] arm64: dts: imx8mm-var-som-symphony: Add Variscite Symphony board with VAR-SOM-MX8MM

[Krzysztof Kozlowski]

Add a DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MM
System on Module.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v2:
1. Use 'led' as node name to be generic,
2. Remove orphaned pinctrl-names.
3. Use more specific regulator node names.

Changes since v1:
1. Remove duplicated "leds" node,
2. Fix heartbeat to active low,
3. Add nxp,ptn5150 extcon.
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mm-var-som-symphony.dts | 246 ++++++++++++++++++
 2 files changed, 247 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 903c0eb61290..a1656f483c29 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -30,6 +30,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
 
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
new file mode 100644
index 000000000000..0bca737964d5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+/dts-v1/;
+
+#include "imx8mm-var-som.dtsi"
+
+/ {
+	model = "Variscite VAR-SOM-MX8MM Symphony evaluation board";
+	compatible = "variscite,var-som-mx8mm-symphony", "variscite,var-som-mx8mm", "fsl,imx8mm";
+
+	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb_otg2_vbus>;
+		regulator-name = "usb_otg2_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		back {
+			label = "Back";
+			gpios = <&pca9534 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BACK>;
+		};
+
+		home {
+			label = "Home";
+			gpios = <&pca9534 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		menu {
+			label = "Menu";
+			gpios = <&pca9534 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MENU>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led {
+			label = "Heartbeat";
+			gpios = <&pca9534 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ethphy {
+	reset-gpios = <&pca9534 5 GPIO_ACTIVE_HIGH>;
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pca9534: gpio@20 {
+		compatible = "nxp,pca9534";
+		reg = <0x20>;
+		gpio-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pca9534>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		#gpio-cells = <2>;
+		wakeup-source;
+
+		/* USB 3.0 OTG (usbotg1) / SATA port switch, set to USB 3.0 */
+		usb3-sata-sel-hog {
+			gpio-hog;
+			gpios = <4 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "usb3_sata_sel";
+		};
+
+		som-vselect-hog {
+			gpio-hog;
+			gpios = <6 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "som_vselect";
+		};
+
+		enet-sel-hog {
+			gpio-hog;
+			gpios = <7 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "enet_sel";
+		};
+	};
+
+	extcon_usbotg1: typec@3d {
+		compatible = "nxp,ptn5150";
+		reg = <0x3d>;
+		int-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ptn5150>;
+		status = "okay";
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	/* Capacitive touch controller */
+	ft5x06_ts: touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_captouch>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <4 GPIO_ACTIVE_HIGH>;
+
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1337";
+		reg = <0x68>;
+		wakeup-source;
+	};
+};
+
+/* Header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* Header */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbotg1 {
+	disable-over-current;
+	extcon = <&extcon_usbotg1>, <&extcon_usbotg1>;
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	disable-over-current;
+	/delete-property/ usb-role-switch;
+	/*
+	 * FIXME: having USB2 enabled hangs the boot just after:
+	 * [    1.943365] ci_hdrc ci_hdrc.1: EHCI Host Controller
+	 * [    1.948287] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
+	 * [    1.971006] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
+	 * [    1.977203] hub 1-0:1.0: USB hub found
+	 * [    1.980987] hub 1-0:1.0: 1 port detected
+	 */
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_captouch: captouchgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4		0x16
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x19
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_pca9534: pca9534grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7	0x16
+		>;
+	};
+
+	pinctrl_ptn5150: ptn5150grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11	0x16
+		>;
+	};
+
+	pinctrl_reg_usb_otg2_vbus: regusbotg2vbusgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1		0x16
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX	0x140
+			MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX	0x140
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x140
+		>;
+	};
+};
-- 
2.17.1

[PATCH v3 4/4] arm64: dts: imx8mm-var-som-symphony: Add Variscite Symphony board with VAR-SOM-MX8MM

[Krzysztof Kozlowski]

Add a DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MM
System on Module.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v2:
1. Use 'led' as node name to be generic,
2. Remove orphaned pinctrl-names.
3. Use more specific regulator node names.

Changes since v1:
1. Remove duplicated "leds" node,
2. Fix heartbeat to active low,
3. Add nxp,ptn5150 extcon.
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mm-var-som-symphony.dts | 246 ++++++++++++++++++
 2 files changed, 247 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 903c0eb61290..a1656f483c29 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -30,6 +30,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
 
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
new file mode 100644
index 000000000000..0bca737964d5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+/dts-v1/;
+
+#include "imx8mm-var-som.dtsi"
+
+/ {
+	model = "Variscite VAR-SOM-MX8MM Symphony evaluation board";
+	compatible = "variscite,var-som-mx8mm-symphony", "variscite,var-som-mx8mm", "fsl,imx8mm";
+
+	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb_otg2_vbus>;
+		regulator-name = "usb_otg2_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		back {
+			label = "Back";
+			gpios = <&pca9534 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BACK>;
+		};
+
+		home {
+			label = "Home";
+			gpios = <&pca9534 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		menu {
+			label = "Menu";
+			gpios = <&pca9534 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MENU>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led {
+			label = "Heartbeat";
+			gpios = <&pca9534 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ethphy {
+	reset-gpios = <&pca9534 5 GPIO_ACTIVE_HIGH>;
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pca9534: gpio@20 {
+		compatible = "nxp,pca9534";
+		reg = <0x20>;
+		gpio-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pca9534>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		#gpio-cells = <2>;
+		wakeup-source;
+
+		/* USB 3.0 OTG (usbotg1) / SATA port switch, set to USB 3.0 */
+		usb3-sata-sel-hog {
+			gpio-hog;
+			gpios = <4 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "usb3_sata_sel";
+		};
+
+		som-vselect-hog {
+			gpio-hog;
+			gpios = <6 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "som_vselect";
+		};
+
+		enet-sel-hog {
+			gpio-hog;
+			gpios = <7 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "enet_sel";
+		};
+	};
+
+	extcon_usbotg1: typec@3d {
+		compatible = "nxp,ptn5150";
+		reg = <0x3d>;
+		int-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ptn5150>;
+		status = "okay";
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	/* Capacitive touch controller */
+	ft5x06_ts: touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_captouch>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <4 GPIO_ACTIVE_HIGH>;
+
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1337";
+		reg = <0x68>;
+		wakeup-source;
+	};
+};
+
+/* Header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* Header */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbotg1 {
+	disable-over-current;
+	extcon = <&extcon_usbotg1>, <&extcon_usbotg1>;
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	disable-over-current;
+	/delete-property/ usb-role-switch;
+	/*
+	 * FIXME: having USB2 enabled hangs the boot just after:
+	 * [    1.943365] ci_hdrc ci_hdrc.1: EHCI Host Controller
+	 * [    1.948287] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
+	 * [    1.971006] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
+	 * [    1.977203] hub 1-0:1.0: USB hub found
+	 * [    1.980987] hub 1-0:1.0: 1 port detected
+	 */
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_captouch: captouchgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4		0x16
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x19
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_pca9534: pca9534grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7	0x16
+		>;
+	};
+
+	pinctrl_ptn5150: ptn5150grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11	0x16
+		>;
+	};
+
+	pinctrl_reg_usb_otg2_vbus: regusbotg2vbusgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1		0x16
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX	0x140
+			MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX	0x140
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x140
+		>;
+	};
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Fabio Estevam]

Hi Krzysztof,

On Mon, Aug 24, 2020 at 1:03 PM Krzysztof Kozlowski <krzk@kernel.org> wrote:

> +&ecspi1 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_ecspi1>;
> +       cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>,
> +                  <&gpio1  0 GPIO_ACTIVE_HIGH>;

These should be active low as 'spi-cs-high' is not passed.

Re: [PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Fabio Estevam]

Hi Krzysztof,

On Mon, Aug 24, 2020 at 1:03 PM Krzysztof Kozlowski <krzk@kernel.org> wrote:

> +&ecspi1 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_ecspi1>;
> +       cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>,
> +                  <&gpio1  0 GPIO_ACTIVE_HIGH>;

These should be active low as 'spi-cs-high' is not passed.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Krzysztof Kozlowski]

On Mon, Aug 24, 2020 at 03:33:50PM -0300, Fabio Estevam wrote:
> Hi Krzysztof,
> 
> On Mon, Aug 24, 2020 at 1:03 PM Krzysztof Kozlowski <krzk@kernel.org> wrote:
> 
> > +&ecspi1 {
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&pinctrl_ecspi1>;
> > +       cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>,
> > +                  <&gpio1  0 GPIO_ACTIVE_HIGH>;
> 
> These should be active low as 'spi-cs-high' is not passed.

True, I'll fix it up, thanks.

Any comments for the Symphony DTS before v4?

Best regards,
Krzysztof

Re: [PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Krzysztof Kozlowski]

On Mon, Aug 24, 2020 at 03:33:50PM -0300, Fabio Estevam wrote:
> Hi Krzysztof,
> 
> On Mon, Aug 24, 2020 at 1:03 PM Krzysztof Kozlowski <krzk@kernel.org> wrote:
> 
> > +&ecspi1 {
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&pinctrl_ecspi1>;
> > +       cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>,
> > +                  <&gpio1  0 GPIO_ACTIVE_HIGH>;
> 
> These should be active low as 'spi-cs-high' is not passed.

True, I'll fix it up, thanks.

Any comments for the Symphony DTS before v4?

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Fabio Estevam]

On Mon, Aug 24, 2020 at 3:57 PM Krzysztof Kozlowski <krzk@kernel.org> wrote:

> True, I'll fix it up, thanks.
>
> Any comments for the Symphony DTS before v4?

It looks good.

One suggestion is to remove pinctrl_pcie0 for now and add it when PCI
support is in place.

Re: [PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Fabio Estevam]

On Mon, Aug 24, 2020 at 3:57 PM Krzysztof Kozlowski <krzk@kernel.org> wrote:

> True, I'll fix it up, thanks.
>
> Any comments for the Symphony DTS before v4?

It looks good.

One suggestion is to remove pinctrl_pcie0 for now and add it when PCI
support is in place.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Krzysztof Kozlowski]

On Mon, Aug 24, 2020 at 04:03:53PM -0300, Fabio Estevam wrote:
> On Mon, Aug 24, 2020 at 3:57 PM Krzysztof Kozlowski <krzk@kernel.org> wrote:
> 
> > True, I'll fix it up, thanks.
> >
> > Any comments for the Symphony DTS before v4?
> 
> It looks good.
> 
> One suggestion is to remove pinctrl_pcie0 for now and add it when PCI
> support is in place.

Indeed, a left over from a removed PCIe node.

Thanks for review.

Best regards,
Krzysztof

Re: [PATCH v3 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module

[Krzysztof Kozlowski]

On Mon, Aug 24, 2020 at 04:03:53PM -0300, Fabio Estevam wrote:
> On Mon, Aug 24, 2020 at 3:57 PM Krzysztof Kozlowski <krzk@kernel.org> wrote:
> 
> > True, I'll fix it up, thanks.
> >
> > Any comments for the Symphony DTS before v4?
> 
> It looks good.
> 
> One suggestion is to remove pinctrl_pcie0 for now and add it when PCI
> support is in place.

Indeed, a left over from a removed PCIe node.

Thanks for review.

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel