* [PATCH v2 1/2] dt-bindings: phy: qcom,qmp: add IPQ8074 PCIe Gen3 PHY binding @ 2022-06-21 11:18 ` Robert Marko 0 siblings, 0 replies; 8+ messages in thread From: Robert Marko @ 2022-06-21 11:18 UTC (permalink / raw) To: agross, bjorn.andersson, kishon, vkoul, robh+dt, krzysztof.kozlowski+dt, linux-arm-msm, linux-phy, devicetree, linux-kernel Cc: Robert Marko, Krzysztof Kozlowski IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. Gen2 one is already supported, document the bindings for the Gen3 one. Signed-off-by: Robert Marko <robimarko@gmail.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml index 8b850c5ab116..220788ce215f 100644 --- a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml +++ b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml @@ -19,6 +19,7 @@ properties: enum: - qcom,ipq6018-qmp-pcie-phy - qcom,ipq6018-qmp-usb3-phy + - qcom,ipq8074-qmp-gen3-pcie-phy - qcom,ipq8074-qmp-pcie-phy - qcom,ipq8074-qmp-usb3-phy - qcom,msm8996-qmp-pcie-phy @@ -312,6 +313,7 @@ allOf: contains: enum: - qcom,ipq6018-qmp-pcie-phy + - qcom,ipq8074-qmp-gen3-pcie-phy - qcom,ipq8074-qmp-pcie-phy then: properties: -- 2.36.1 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 1/2] dt-bindings: phy: qcom,qmp: add IPQ8074 PCIe Gen3 PHY binding @ 2022-06-21 11:18 ` Robert Marko 0 siblings, 0 replies; 8+ messages in thread From: Robert Marko @ 2022-06-21 11:18 UTC (permalink / raw) To: agross, bjorn.andersson, kishon, vkoul, robh+dt, krzysztof.kozlowski+dt, linux-arm-msm, linux-phy, devicetree, linux-kernel Cc: Robert Marko, Krzysztof Kozlowski IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. Gen2 one is already supported, document the bindings for the Gen3 one. Signed-off-by: Robert Marko <robimarko@gmail.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml index 8b850c5ab116..220788ce215f 100644 --- a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml +++ b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml @@ -19,6 +19,7 @@ properties: enum: - qcom,ipq6018-qmp-pcie-phy - qcom,ipq6018-qmp-usb3-phy + - qcom,ipq8074-qmp-gen3-pcie-phy - qcom,ipq8074-qmp-pcie-phy - qcom,ipq8074-qmp-usb3-phy - qcom,msm8996-qmp-pcie-phy @@ -312,6 +313,7 @@ allOf: contains: enum: - qcom,ipq6018-qmp-pcie-phy + - qcom,ipq8074-qmp-gen3-pcie-phy - qcom,ipq8074-qmp-pcie-phy then: properties: -- 2.36.1 -- linux-phy mailing list linux-phy@lists.infradead.org https://lists.infradead.org/mailman/listinfo/linux-phy ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 2/2] phy: qcom-qmp-pcie: add IPQ8074 PCIe Gen3 QMP PHY support 2022-06-21 11:18 ` Robert Marko @ 2022-06-21 11:18 ` Robert Marko -1 siblings, 0 replies; 8+ messages in thread From: Robert Marko @ 2022-06-21 11:18 UTC (permalink / raw) To: agross, bjorn.andersson, kishon, vkoul, robh+dt, krzysztof.kozlowski+dt, linux-arm-msm, linux-phy, devicetree, linux-kernel Cc: Robert Marko IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. Gen2 one is already supported, so add the support for the Gen3 one. It uses the same register layout as IPQ6018. Signed-off-by: Robert Marko <robimarko@gmail.com> --- Changes in v2: * Rebase onto next-20220621 to apply on the refactored driver * Remove non existant has_phy_com_ctrl and has_lane_rst --- drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 171 ++++++++++++++++++++++- 1 file changed, 169 insertions(+), 2 deletions(-) diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c index b2cd0cf965d8..b4836417b2c0 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c @@ -450,6 +450,133 @@ static const struct qmp_phy_init_tbl ipq8074_pcie_pcs_tbl[] = { QMP_PHY_INIT_CFG_L(QPHY_START_CTRL, 0x3), }; +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_serdes_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_PLL_BIAS_EN_CLKBUFLR_EN, 0x18), + QMP_PHY_INIT_CFG(QSERDES_PLL_BIAS_EN_CTRL_BY_PSM, 0x01), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_SELECT, 0x31), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_IVCO, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_PLL_BG_TRIM, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_PLL_CMN_CONFIG, 0x06), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP_EN, 0x42), + QMP_PHY_INIT_CFG(QSERDES_PLL_RESETSM_CNTRL, 0x20), + QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x01), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE_MAP, 0x04), + QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x05), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE_TIMER1, 0xff), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE_TIMER2, 0x3f), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORE_CLK_EN, 0x30), + QMP_PHY_INIT_CFG(QSERDES_PLL_HSCLK_SEL, 0x21), + QMP_PHY_INIT_CFG(QSERDES_PLL_DEC_START_MODE0, 0x82), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START3_MODE0, 0x03), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START2_MODE0, 0x355), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START1_MODE0, 0x35555), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP2_MODE0, 0x1a), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP1_MODE0, 0x1a0a), + QMP_PHY_INIT_CFG(QSERDES_PLL_CP_CTRL_MODE0, 0xb), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_RCTRL_MODE0, 0x16), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_CCTRL_MODE0, 0x28), + QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN1_MODE0, 0x0), + QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN0_MODE0, 0x40), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE2_MODE0, 0x02), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE1_MODE0, 0x24), + QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x05), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORE_CLK_EN, 0x20), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORECLK_DIV, 0xa), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_SELECT, 0x32), + QMP_PHY_INIT_CFG(QSERDES_PLL_SYS_CLK_CTRL, 0x02), + QMP_PHY_INIT_CFG(QSERDES_PLL_SYSCLK_BUF_ENABLE, 0x07), + QMP_PHY_INIT_CFG(QSERDES_PLL_SYSCLK_EN_SEL, 0x08), + QMP_PHY_INIT_CFG(QSERDES_PLL_BG_TIMER, 0xa), + QMP_PHY_INIT_CFG(QSERDES_PLL_HSCLK_SEL, 0x1), + QMP_PHY_INIT_CFG(QSERDES_PLL_DEC_START_MODE1, 0x68), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START3_MODE1, 0x2), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START2_MODE1, 0x2aa), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START1_MODE1, 0x2aaab), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_ENABLE1, 0x90), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP2_MODE1, 0x34), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP1_MODE1, 0x3414), + QMP_PHY_INIT_CFG(QSERDES_PLL_CP_CTRL_MODE1, 0x0b), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_RCTRL_MODE1, 0x16), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_CCTRL_MODE1, 0x28), + QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN1_MODE1, 0x0), + QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN0_MODE1, 0x40), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE2_MODE1, 0x03), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE1_MODE1, 0xb4), + QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x05), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORE_CLK_EN, 0x0), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORECLK_DIV_MODE1, 0x08), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_EP_DIV_MODE0, 0x19), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_EP_DIV_MODE1, 0x28), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_ENABLE1, 0x90), +}; + +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_tx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_TX0_RES_CODE_LANE_OFFSET_TX, 0x02), + QMP_PHY_INIT_CFG(QSERDES_TX0_RCV_DETECT_LVL_2, 0x12), + QMP_PHY_INIT_CFG(QSERDES_TX0_HIGHZ_DRVR_EN, 0x10), + QMP_PHY_INIT_CFG(QSERDES_TX0_LANE_MODE_1, 0x06), +}; + +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_RX0_SIGDET_CNTRL, 0x03), + QMP_PHY_INIT_CFG(QSERDES_RX0_SIGDET_ENABLES, 0x1c), + QMP_PHY_INIT_CFG(QSERDES_RX0_SIGDET_DEGLITCH_CNTRL, 0x14), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_EQU_ADAPTOR_CNTRL2, 0xe), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_EQU_ADAPTOR_CNTRL3, 0x4), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_EQU_ADAPTOR_CNTRL4, 0x1b), + QMP_PHY_INIT_CFG(QSERDES_RX0_DFE_EN_TIMER, 0x04), + QMP_PHY_INIT_CFG(QSERDES_RX0_UCDR_SO_SATURATION_AND_ENABLE, 0x7f), + QMP_PHY_INIT_CFG(QSERDES_RX0_UCDR_PI_CONTROLS, 0x70), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x73), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_OFFSET_ADAPTOR_CNTRL2, 0x80), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_LOW, 0x00), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_HIGH, 0x02), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_HIGH2, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_HIGH3, 0x09), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_HIGH4, 0xb1), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_LOW, 0x01), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_HIGH, 0x02), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_HIGH2, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_HIGH3, 0x09), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_HIGH4, 0xb1), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_LOW, 0xf0), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_HIGH, 0x2), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_HIGH2, 0x2f), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_HIGH3, 0xd3), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_HIGH4, 0x40), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_IDAC_TSETTLE_HIGH, 0x00), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_IDAC_TSETTLE_LOW, 0xc0), + QMP_PHY_INIT_CFG(QSERDES_RX0_UCDR_FO_GAIN, 0x0c), + QMP_PHY_INIT_CFG(QSERDES_RX0_UCDR_SO_GAIN, 0x02), +}; + +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_pcs_tbl[] = { + QMP_PHY_INIT_CFG(PCS_COM_FLL_CNTRL2, 0x83), + QMP_PHY_INIT_CFG(PCS_COM_FLL_CNT_VAL_L, 0x9), + QMP_PHY_INIT_CFG(PCS_COM_FLL_CNT_VAL_H_TOL, 0x42), + QMP_PHY_INIT_CFG(PCS_COM_FLL_MAN_CODE, 0x40), + QMP_PHY_INIT_CFG(PCS_COM_FLL_CNTRL1, 0x01), + QMP_PHY_INIT_CFG(PCS_COM_P2U3_WAKEUP_DLY_TIME_AUXCLK_H, 0x0), + QMP_PHY_INIT_CFG(PCS_COM_P2U3_WAKEUP_DLY_TIME_AUXCLK_L, 0x1), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_ACTIONS, 0x0), + QMP_PHY_INIT_CFG(PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_H, 0x00), + QMP_PHY_INIT_CFG(PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_L, 0x01), + QMP_PHY_INIT_CFG(PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_H, 0x00), + QMP_PHY_INIT_CFG(PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_L, 0x01), + QMP_PHY_INIT_CFG(PCS_PCIE_EQ_CONFIG1, 0x11), + QMP_PHY_INIT_CFG(PCS_PCIE_EQ_CONFIG2, 0xb), + QMP_PHY_INIT_CFG(PCS_PCIE_POWER_STATE_CONFIG4, 0x07), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_CONFIG2, 0x52), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_MODE2_CONFIG2, 0x50), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_MODE2_CONFIG4, 0x1a), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x6), + QMP_PHY_INIT_CFG(PCS_COM_G12S1_TXDEEMPH_M3P5DB, 0x10), + QMP_PHY_INIT_CFG(PCS_PCIE_ENDPOINT_REFCLK_DRIVE, 0xc1), + QMP_PHY_INIT_CFG(PCS_COM_RX_DCC_CAL_CONFIG, 0x01), + QMP_PHY_INIT_CFG(PCS_COM_RX_SIGDET_LVL, 0xaa), + QMP_PHY_INIT_CFG(PCS_COM_REFGEN_REQ_CONFIG1, 0x0d), +}; + static const struct qmp_phy_init_tbl sdm845_qmp_pcie_serdes_tbl[] = { QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x14), QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30), @@ -1421,6 +1548,34 @@ static const struct qmp_phy_cfg ipq8074_pciephy_cfg = { .pwrdn_delay_max = 1005, /* us */ }; +static const struct qmp_phy_cfg ipq8074_pciephy_gen3_cfg = { + .type = PHY_TYPE_PCIE, + .nlanes = 1, + + .serdes_tbl = ipq8074_pcie_gen3_serdes_tbl, + .serdes_tbl_num = ARRAY_SIZE(ipq8074_pcie_gen3_serdes_tbl), + .tx_tbl = ipq8074_pcie_gen3_tx_tbl, + .tx_tbl_num = ARRAY_SIZE(ipq8074_pcie_gen3_tx_tbl), + .rx_tbl = ipq8074_pcie_gen3_rx_tbl, + .rx_tbl_num = ARRAY_SIZE(ipq8074_pcie_gen3_rx_tbl), + .pcs_tbl = ipq8074_pcie_gen3_pcs_tbl, + .pcs_tbl_num = ARRAY_SIZE(ipq8074_pcie_gen3_pcs_tbl), + .clk_list = ipq8074_pciephy_clk_l, + .num_clks = ARRAY_SIZE(ipq8074_pciephy_clk_l), + .reset_list = ipq8074_pciephy_reset_l, + .num_resets = ARRAY_SIZE(ipq8074_pciephy_reset_l), + .vreg_list = NULL, + .num_vregs = 0, + .regs = ipq_pciephy_gen3_regs_layout, + + .start_ctrl = SERDES_START | PCS_START, + .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL, + + .has_pwrdn_delay = true, + .pwrdn_delay_min = 995, /* us */ + .pwrdn_delay_max = 1005, /* us */ +}; + static const struct qmp_phy_cfg ipq6018_pciephy_cfg = { .type = PHY_TYPE_PCIE, .nlanes = 1, @@ -2107,6 +2262,7 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) { struct clk_fixed_rate *fixed; struct clk_init_data init = { }; + u32 rate; int ret; ret = of_property_read_string(np, "clock-output-names", &init.name); @@ -2121,8 +2277,16 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) init.ops = &clk_fixed_rate_ops; - /* controllers using QMP phys use 125MHz pipe clock interface */ - fixed->fixed_rate = 125000000; + /* + * Controllers using QMP PHY-s use 125MHz pipe clock interface + * unless other frequency is specified in the DTS. + */ + ret = of_property_read_u32(np, "clock-output-rate", &rate); + if (ret) + fixed->fixed_rate = 125000000; + else + fixed->fixed_rate = rate; + fixed->hw.init = &init; ret = devm_clk_hw_register(qmp->dev, &fixed->hw); @@ -2255,6 +2419,9 @@ static const struct of_device_id qcom_qmp_phy_pcie_of_match_table[] = { }, { .compatible = "qcom,ipq8074-qmp-pcie-phy", .data = &ipq8074_pciephy_cfg, + }, { + .compatible = "qcom,ipq8074-qmp-gen3-pcie-phy", + .data = &ipq8074_pciephy_gen3_cfg, }, { .compatible = "qcom,ipq6018-qmp-pcie-phy", .data = &ipq6018_pciephy_cfg, -- 2.36.1 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 2/2] phy: qcom-qmp-pcie: add IPQ8074 PCIe Gen3 QMP PHY support @ 2022-06-21 11:18 ` Robert Marko 0 siblings, 0 replies; 8+ messages in thread From: Robert Marko @ 2022-06-21 11:18 UTC (permalink / raw) To: agross, bjorn.andersson, kishon, vkoul, robh+dt, krzysztof.kozlowski+dt, linux-arm-msm, linux-phy, devicetree, linux-kernel Cc: Robert Marko IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. Gen2 one is already supported, so add the support for the Gen3 one. It uses the same register layout as IPQ6018. Signed-off-by: Robert Marko <robimarko@gmail.com> --- Changes in v2: * Rebase onto next-20220621 to apply on the refactored driver * Remove non existant has_phy_com_ctrl and has_lane_rst --- drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 171 ++++++++++++++++++++++- 1 file changed, 169 insertions(+), 2 deletions(-) diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c index b2cd0cf965d8..b4836417b2c0 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c @@ -450,6 +450,133 @@ static const struct qmp_phy_init_tbl ipq8074_pcie_pcs_tbl[] = { QMP_PHY_INIT_CFG_L(QPHY_START_CTRL, 0x3), }; +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_serdes_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_PLL_BIAS_EN_CLKBUFLR_EN, 0x18), + QMP_PHY_INIT_CFG(QSERDES_PLL_BIAS_EN_CTRL_BY_PSM, 0x01), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_SELECT, 0x31), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_IVCO, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_PLL_BG_TRIM, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_PLL_CMN_CONFIG, 0x06), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP_EN, 0x42), + QMP_PHY_INIT_CFG(QSERDES_PLL_RESETSM_CNTRL, 0x20), + QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x01), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE_MAP, 0x04), + QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x05), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE_TIMER1, 0xff), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE_TIMER2, 0x3f), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORE_CLK_EN, 0x30), + QMP_PHY_INIT_CFG(QSERDES_PLL_HSCLK_SEL, 0x21), + QMP_PHY_INIT_CFG(QSERDES_PLL_DEC_START_MODE0, 0x82), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START3_MODE0, 0x03), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START2_MODE0, 0x355), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START1_MODE0, 0x35555), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP2_MODE0, 0x1a), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP1_MODE0, 0x1a0a), + QMP_PHY_INIT_CFG(QSERDES_PLL_CP_CTRL_MODE0, 0xb), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_RCTRL_MODE0, 0x16), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_CCTRL_MODE0, 0x28), + QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN1_MODE0, 0x0), + QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN0_MODE0, 0x40), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE2_MODE0, 0x02), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE1_MODE0, 0x24), + QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x05), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORE_CLK_EN, 0x20), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORECLK_DIV, 0xa), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_SELECT, 0x32), + QMP_PHY_INIT_CFG(QSERDES_PLL_SYS_CLK_CTRL, 0x02), + QMP_PHY_INIT_CFG(QSERDES_PLL_SYSCLK_BUF_ENABLE, 0x07), + QMP_PHY_INIT_CFG(QSERDES_PLL_SYSCLK_EN_SEL, 0x08), + QMP_PHY_INIT_CFG(QSERDES_PLL_BG_TIMER, 0xa), + QMP_PHY_INIT_CFG(QSERDES_PLL_HSCLK_SEL, 0x1), + QMP_PHY_INIT_CFG(QSERDES_PLL_DEC_START_MODE1, 0x68), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START3_MODE1, 0x2), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START2_MODE1, 0x2aa), + QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START1_MODE1, 0x2aaab), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_ENABLE1, 0x90), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP2_MODE1, 0x34), + QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP1_MODE1, 0x3414), + QMP_PHY_INIT_CFG(QSERDES_PLL_CP_CTRL_MODE1, 0x0b), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_RCTRL_MODE1, 0x16), + QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_CCTRL_MODE1, 0x28), + QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN1_MODE1, 0x0), + QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN0_MODE1, 0x40), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE2_MODE1, 0x03), + QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE1_MODE1, 0xb4), + QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x05), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORE_CLK_EN, 0x0), + QMP_PHY_INIT_CFG(QSERDES_PLL_CORECLK_DIV_MODE1, 0x08), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_EP_DIV_MODE0, 0x19), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_EP_DIV_MODE1, 0x28), + QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_ENABLE1, 0x90), +}; + +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_tx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_TX0_RES_CODE_LANE_OFFSET_TX, 0x02), + QMP_PHY_INIT_CFG(QSERDES_TX0_RCV_DETECT_LVL_2, 0x12), + QMP_PHY_INIT_CFG(QSERDES_TX0_HIGHZ_DRVR_EN, 0x10), + QMP_PHY_INIT_CFG(QSERDES_TX0_LANE_MODE_1, 0x06), +}; + +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_RX0_SIGDET_CNTRL, 0x03), + QMP_PHY_INIT_CFG(QSERDES_RX0_SIGDET_ENABLES, 0x1c), + QMP_PHY_INIT_CFG(QSERDES_RX0_SIGDET_DEGLITCH_CNTRL, 0x14), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_EQU_ADAPTOR_CNTRL2, 0xe), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_EQU_ADAPTOR_CNTRL3, 0x4), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_EQU_ADAPTOR_CNTRL4, 0x1b), + QMP_PHY_INIT_CFG(QSERDES_RX0_DFE_EN_TIMER, 0x04), + QMP_PHY_INIT_CFG(QSERDES_RX0_UCDR_SO_SATURATION_AND_ENABLE, 0x7f), + QMP_PHY_INIT_CFG(QSERDES_RX0_UCDR_PI_CONTROLS, 0x70), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x73), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_OFFSET_ADAPTOR_CNTRL2, 0x80), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_LOW, 0x00), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_HIGH, 0x02), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_HIGH2, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_HIGH3, 0x09), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_10_HIGH4, 0xb1), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_LOW, 0x01), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_HIGH, 0x02), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_HIGH2, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_HIGH3, 0x09), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_01_HIGH4, 0xb1), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_LOW, 0xf0), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_HIGH, 0x2), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_HIGH2, 0x2f), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_HIGH3, 0xd3), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_MODE_00_HIGH4, 0x40), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_IDAC_TSETTLE_HIGH, 0x00), + QMP_PHY_INIT_CFG(QSERDES_RX0_RX_IDAC_TSETTLE_LOW, 0xc0), + QMP_PHY_INIT_CFG(QSERDES_RX0_UCDR_FO_GAIN, 0x0c), + QMP_PHY_INIT_CFG(QSERDES_RX0_UCDR_SO_GAIN, 0x02), +}; + +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_pcs_tbl[] = { + QMP_PHY_INIT_CFG(PCS_COM_FLL_CNTRL2, 0x83), + QMP_PHY_INIT_CFG(PCS_COM_FLL_CNT_VAL_L, 0x9), + QMP_PHY_INIT_CFG(PCS_COM_FLL_CNT_VAL_H_TOL, 0x42), + QMP_PHY_INIT_CFG(PCS_COM_FLL_MAN_CODE, 0x40), + QMP_PHY_INIT_CFG(PCS_COM_FLL_CNTRL1, 0x01), + QMP_PHY_INIT_CFG(PCS_COM_P2U3_WAKEUP_DLY_TIME_AUXCLK_H, 0x0), + QMP_PHY_INIT_CFG(PCS_COM_P2U3_WAKEUP_DLY_TIME_AUXCLK_L, 0x1), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_ACTIONS, 0x0), + QMP_PHY_INIT_CFG(PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_H, 0x00), + QMP_PHY_INIT_CFG(PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_L, 0x01), + QMP_PHY_INIT_CFG(PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_H, 0x00), + QMP_PHY_INIT_CFG(PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_L, 0x01), + QMP_PHY_INIT_CFG(PCS_PCIE_EQ_CONFIG1, 0x11), + QMP_PHY_INIT_CFG(PCS_PCIE_EQ_CONFIG2, 0xb), + QMP_PHY_INIT_CFG(PCS_PCIE_POWER_STATE_CONFIG4, 0x07), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_CONFIG2, 0x52), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_MODE2_CONFIG2, 0x50), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_MODE2_CONFIG4, 0x1a), + QMP_PHY_INIT_CFG(PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x6), + QMP_PHY_INIT_CFG(PCS_COM_G12S1_TXDEEMPH_M3P5DB, 0x10), + QMP_PHY_INIT_CFG(PCS_PCIE_ENDPOINT_REFCLK_DRIVE, 0xc1), + QMP_PHY_INIT_CFG(PCS_COM_RX_DCC_CAL_CONFIG, 0x01), + QMP_PHY_INIT_CFG(PCS_COM_RX_SIGDET_LVL, 0xaa), + QMP_PHY_INIT_CFG(PCS_COM_REFGEN_REQ_CONFIG1, 0x0d), +}; + static const struct qmp_phy_init_tbl sdm845_qmp_pcie_serdes_tbl[] = { QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x14), QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30), @@ -1421,6 +1548,34 @@ static const struct qmp_phy_cfg ipq8074_pciephy_cfg = { .pwrdn_delay_max = 1005, /* us */ }; +static const struct qmp_phy_cfg ipq8074_pciephy_gen3_cfg = { + .type = PHY_TYPE_PCIE, + .nlanes = 1, + + .serdes_tbl = ipq8074_pcie_gen3_serdes_tbl, + .serdes_tbl_num = ARRAY_SIZE(ipq8074_pcie_gen3_serdes_tbl), + .tx_tbl = ipq8074_pcie_gen3_tx_tbl, + .tx_tbl_num = ARRAY_SIZE(ipq8074_pcie_gen3_tx_tbl), + .rx_tbl = ipq8074_pcie_gen3_rx_tbl, + .rx_tbl_num = ARRAY_SIZE(ipq8074_pcie_gen3_rx_tbl), + .pcs_tbl = ipq8074_pcie_gen3_pcs_tbl, + .pcs_tbl_num = ARRAY_SIZE(ipq8074_pcie_gen3_pcs_tbl), + .clk_list = ipq8074_pciephy_clk_l, + .num_clks = ARRAY_SIZE(ipq8074_pciephy_clk_l), + .reset_list = ipq8074_pciephy_reset_l, + .num_resets = ARRAY_SIZE(ipq8074_pciephy_reset_l), + .vreg_list = NULL, + .num_vregs = 0, + .regs = ipq_pciephy_gen3_regs_layout, + + .start_ctrl = SERDES_START | PCS_START, + .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL, + + .has_pwrdn_delay = true, + .pwrdn_delay_min = 995, /* us */ + .pwrdn_delay_max = 1005, /* us */ +}; + static const struct qmp_phy_cfg ipq6018_pciephy_cfg = { .type = PHY_TYPE_PCIE, .nlanes = 1, @@ -2107,6 +2262,7 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) { struct clk_fixed_rate *fixed; struct clk_init_data init = { }; + u32 rate; int ret; ret = of_property_read_string(np, "clock-output-names", &init.name); @@ -2121,8 +2277,16 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) init.ops = &clk_fixed_rate_ops; - /* controllers using QMP phys use 125MHz pipe clock interface */ - fixed->fixed_rate = 125000000; + /* + * Controllers using QMP PHY-s use 125MHz pipe clock interface + * unless other frequency is specified in the DTS. + */ + ret = of_property_read_u32(np, "clock-output-rate", &rate); + if (ret) + fixed->fixed_rate = 125000000; + else + fixed->fixed_rate = rate; + fixed->hw.init = &init; ret = devm_clk_hw_register(qmp->dev, &fixed->hw); @@ -2255,6 +2419,9 @@ static const struct of_device_id qcom_qmp_phy_pcie_of_match_table[] = { }, { .compatible = "qcom,ipq8074-qmp-pcie-phy", .data = &ipq8074_pciephy_cfg, + }, { + .compatible = "qcom,ipq8074-qmp-gen3-pcie-phy", + .data = &ipq8074_pciephy_gen3_cfg, }, { .compatible = "qcom,ipq6018-qmp-pcie-phy", .data = &ipq6018_pciephy_cfg, -- 2.36.1 -- linux-phy mailing list linux-phy@lists.infradead.org https://lists.infradead.org/mailman/listinfo/linux-phy ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v2 2/2] phy: qcom-qmp-pcie: add IPQ8074 PCIe Gen3 QMP PHY support 2022-06-21 11:18 ` Robert Marko @ 2022-06-21 17:26 ` Dmitry Baryshkov -1 siblings, 0 replies; 8+ messages in thread From: Dmitry Baryshkov @ 2022-06-21 17:26 UTC (permalink / raw) To: Robert Marko Cc: agross, bjorn.andersson, kishon, vkoul, robh+dt, krzysztof.kozlowski+dt, linux-arm-msm, linux-phy, devicetree, linux-kernel On Tue, 21 Jun 2022 at 14:18, Robert Marko <robimarko@gmail.com> wrote: > > IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. > Gen2 one is already supported, so add the support for the Gen3 one. > It uses the same register layout as IPQ6018. > > Signed-off-by: Robert Marko <robimarko@gmail.com> > --- > Changes in v2: > * Rebase onto next-20220621 to apply on the refactored driver > * Remove non existant has_phy_com_ctrl and has_lane_rst > --- > drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 171 ++++++++++++++++++++++- > 1 file changed, 169 insertions(+), 2 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > index b2cd0cf965d8..b4836417b2c0 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c [skipped] > @@ -2121,8 +2277,16 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) > > init.ops = &clk_fixed_rate_ops; > > - /* controllers using QMP phys use 125MHz pipe clock interface */ > - fixed->fixed_rate = 125000000; > + /* > + * Controllers using QMP PHY-s use 125MHz pipe clock interface > + * unless other frequency is specified in the DTS. > + */ > + ret = of_property_read_u32(np, "clock-output-rate", &rate); The clock-output-rate is a new property, which doesn't exist yet. If the rate is peculiar to your platform/PHY, I'd suggest adding a field to the qmp configuration instead. > + if (ret) > + fixed->fixed_rate = 125000000; > + else > + fixed->fixed_rate = rate; > + > fixed->hw.init = &init; > > ret = devm_clk_hw_register(qmp->dev, &fixed->hw); > @@ -2255,6 +2419,9 @@ static const struct of_device_id qcom_qmp_phy_pcie_of_match_table[] = { > }, { > .compatible = "qcom,ipq8074-qmp-pcie-phy", > .data = &ipq8074_pciephy_cfg, > + }, { > + .compatible = "qcom,ipq8074-qmp-gen3-pcie-phy", > + .data = &ipq8074_pciephy_gen3_cfg, > }, { > .compatible = "qcom,ipq6018-qmp-pcie-phy", > .data = &ipq6018_pciephy_cfg, > -- > 2.36.1 > -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 2/2] phy: qcom-qmp-pcie: add IPQ8074 PCIe Gen3 QMP PHY support @ 2022-06-21 17:26 ` Dmitry Baryshkov 0 siblings, 0 replies; 8+ messages in thread From: Dmitry Baryshkov @ 2022-06-21 17:26 UTC (permalink / raw) To: Robert Marko Cc: agross, bjorn.andersson, kishon, vkoul, robh+dt, krzysztof.kozlowski+dt, linux-arm-msm, linux-phy, devicetree, linux-kernel On Tue, 21 Jun 2022 at 14:18, Robert Marko <robimarko@gmail.com> wrote: > > IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. > Gen2 one is already supported, so add the support for the Gen3 one. > It uses the same register layout as IPQ6018. > > Signed-off-by: Robert Marko <robimarko@gmail.com> > --- > Changes in v2: > * Rebase onto next-20220621 to apply on the refactored driver > * Remove non existant has_phy_com_ctrl and has_lane_rst > --- > drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 171 ++++++++++++++++++++++- > 1 file changed, 169 insertions(+), 2 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > index b2cd0cf965d8..b4836417b2c0 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c [skipped] > @@ -2121,8 +2277,16 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) > > init.ops = &clk_fixed_rate_ops; > > - /* controllers using QMP phys use 125MHz pipe clock interface */ > - fixed->fixed_rate = 125000000; > + /* > + * Controllers using QMP PHY-s use 125MHz pipe clock interface > + * unless other frequency is specified in the DTS. > + */ > + ret = of_property_read_u32(np, "clock-output-rate", &rate); The clock-output-rate is a new property, which doesn't exist yet. If the rate is peculiar to your platform/PHY, I'd suggest adding a field to the qmp configuration instead. > + if (ret) > + fixed->fixed_rate = 125000000; > + else > + fixed->fixed_rate = rate; > + > fixed->hw.init = &init; > > ret = devm_clk_hw_register(qmp->dev, &fixed->hw); > @@ -2255,6 +2419,9 @@ static const struct of_device_id qcom_qmp_phy_pcie_of_match_table[] = { > }, { > .compatible = "qcom,ipq8074-qmp-pcie-phy", > .data = &ipq8074_pciephy_cfg, > + }, { > + .compatible = "qcom,ipq8074-qmp-gen3-pcie-phy", > + .data = &ipq8074_pciephy_gen3_cfg, > }, { > .compatible = "qcom,ipq6018-qmp-pcie-phy", > .data = &ipq6018_pciephy_cfg, > -- > 2.36.1 > -- With best wishes Dmitry -- linux-phy mailing list linux-phy@lists.infradead.org https://lists.infradead.org/mailman/listinfo/linux-phy ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 2/2] phy: qcom-qmp-pcie: add IPQ8074 PCIe Gen3 QMP PHY support 2022-06-21 17:26 ` Dmitry Baryshkov @ 2022-06-21 18:42 ` Robert Marko -1 siblings, 0 replies; 8+ messages in thread From: Robert Marko @ 2022-06-21 18:42 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Andy Gross, Bjorn Andersson, kishon, Vinod Koul, Rob Herring, krzysztof.kozlowski+dt, linux-arm-msm, linux-phy, Devicetree List, open list On Tue, 21 Jun 2022 at 19:26, Dmitry Baryshkov <dmitry.baryshkov@linaro.org> wrote: > > On Tue, 21 Jun 2022 at 14:18, Robert Marko <robimarko@gmail.com> wrote: > > > > IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. > > Gen2 one is already supported, so add the support for the Gen3 one. > > It uses the same register layout as IPQ6018. > > > > Signed-off-by: Robert Marko <robimarko@gmail.com> > > --- > > Changes in v2: > > * Rebase onto next-20220621 to apply on the refactored driver > > * Remove non existant has_phy_com_ctrl and has_lane_rst > > --- > > drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 171 ++++++++++++++++++++++- > > 1 file changed, 169 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > > index b2cd0cf965d8..b4836417b2c0 100644 > > --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > > [skipped] > > > @@ -2121,8 +2277,16 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) > > > > init.ops = &clk_fixed_rate_ops; > > > > - /* controllers using QMP phys use 125MHz pipe clock interface */ > > - fixed->fixed_rate = 125000000; > > + /* > > + * Controllers using QMP PHY-s use 125MHz pipe clock interface > > + * unless other frequency is specified in the DTS. > > + */ > > + ret = of_property_read_u32(np, "clock-output-rate", &rate); > > The clock-output-rate is a new property, which doesn't exist yet. If > the rate is peculiar to your platform/PHY, I'd suggest adding a field > to the qmp configuration instead. Hi, That sounds like a better idea than adding new DT property, it's specific only to the Gen3 PHY for IPQ8074. I will change it for v3. Regards, Robert > > > + if (ret) > > + fixed->fixed_rate = 125000000; > > + else > > + fixed->fixed_rate = rate; > > + > > fixed->hw.init = &init; > > > > ret = devm_clk_hw_register(qmp->dev, &fixed->hw); > > @@ -2255,6 +2419,9 @@ static const struct of_device_id qcom_qmp_phy_pcie_of_match_table[] = { > > }, { > > .compatible = "qcom,ipq8074-qmp-pcie-phy", > > .data = &ipq8074_pciephy_cfg, > > + }, { > > + .compatible = "qcom,ipq8074-qmp-gen3-pcie-phy", > > + .data = &ipq8074_pciephy_gen3_cfg, > > }, { > > .compatible = "qcom,ipq6018-qmp-pcie-phy", > > .data = &ipq6018_pciephy_cfg, > > -- > > 2.36.1 > > > > > -- > With best wishes > Dmitry ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 2/2] phy: qcom-qmp-pcie: add IPQ8074 PCIe Gen3 QMP PHY support @ 2022-06-21 18:42 ` Robert Marko 0 siblings, 0 replies; 8+ messages in thread From: Robert Marko @ 2022-06-21 18:42 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Andy Gross, Bjorn Andersson, kishon, Vinod Koul, Rob Herring, krzysztof.kozlowski+dt, linux-arm-msm, linux-phy, Devicetree List, open list On Tue, 21 Jun 2022 at 19:26, Dmitry Baryshkov <dmitry.baryshkov@linaro.org> wrote: > > On Tue, 21 Jun 2022 at 14:18, Robert Marko <robimarko@gmail.com> wrote: > > > > IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. > > Gen2 one is already supported, so add the support for the Gen3 one. > > It uses the same register layout as IPQ6018. > > > > Signed-off-by: Robert Marko <robimarko@gmail.com> > > --- > > Changes in v2: > > * Rebase onto next-20220621 to apply on the refactored driver > > * Remove non existant has_phy_com_ctrl and has_lane_rst > > --- > > drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 171 ++++++++++++++++++++++- > > 1 file changed, 169 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > > index b2cd0cf965d8..b4836417b2c0 100644 > > --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c > > [skipped] > > > @@ -2121,8 +2277,16 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) > > > > init.ops = &clk_fixed_rate_ops; > > > > - /* controllers using QMP phys use 125MHz pipe clock interface */ > > - fixed->fixed_rate = 125000000; > > + /* > > + * Controllers using QMP PHY-s use 125MHz pipe clock interface > > + * unless other frequency is specified in the DTS. > > + */ > > + ret = of_property_read_u32(np, "clock-output-rate", &rate); > > The clock-output-rate is a new property, which doesn't exist yet. If > the rate is peculiar to your platform/PHY, I'd suggest adding a field > to the qmp configuration instead. Hi, That sounds like a better idea than adding new DT property, it's specific only to the Gen3 PHY for IPQ8074. I will change it for v3. Regards, Robert > > > + if (ret) > > + fixed->fixed_rate = 125000000; > > + else > > + fixed->fixed_rate = rate; > > + > > fixed->hw.init = &init; > > > > ret = devm_clk_hw_register(qmp->dev, &fixed->hw); > > @@ -2255,6 +2419,9 @@ static const struct of_device_id qcom_qmp_phy_pcie_of_match_table[] = { > > }, { > > .compatible = "qcom,ipq8074-qmp-pcie-phy", > > .data = &ipq8074_pciephy_cfg, > > + }, { > > + .compatible = "qcom,ipq8074-qmp-gen3-pcie-phy", > > + .data = &ipq8074_pciephy_gen3_cfg, > > }, { > > .compatible = "qcom,ipq6018-qmp-pcie-phy", > > .data = &ipq6018_pciephy_cfg, > > -- > > 2.36.1 > > > > > -- > With best wishes > Dmitry -- linux-phy mailing list linux-phy@lists.infradead.org https://lists.infradead.org/mailman/listinfo/linux-phy ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2022-06-21 18:42 UTC | newest] Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2022-06-21 11:18 [PATCH v2 1/2] dt-bindings: phy: qcom,qmp: add IPQ8074 PCIe Gen3 PHY binding Robert Marko 2022-06-21 11:18 ` Robert Marko 2022-06-21 11:18 ` [PATCH v2 2/2] phy: qcom-qmp-pcie: add IPQ8074 PCIe Gen3 QMP PHY support Robert Marko 2022-06-21 11:18 ` Robert Marko 2022-06-21 17:26 ` Dmitry Baryshkov 2022-06-21 17:26 ` Dmitry Baryshkov 2022-06-21 18:42 ` Robert Marko 2022-06-21 18:42 ` Robert Marko
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.