* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-04 17:44 ` Tomasz Figa
0 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-04 17:44 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, linux-kernel, Kukjin Kim, Arnd Bergmann,
Olof Johansson, Marek Szyprowski, Mark Brown, Heiko Stübner,
Tomasz Figa, Tomasz Figa
This huge series is a (hopefully final) attempt to convert Samsung S5PV210
into a DT-only and multiplatform-aware platform. It consists of several
steps to gradually replace legacy code with one meeting current standards
and then finally remove unused remnants.
Patches 1-6 migrate the platform to fully use the Common Clock Framework
and get rid of legacy private clock code, of which s5pv210 was the last
user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
USB to be supported when using DT. Further three patches (8-10) add DT
support for mach-s5pv210 and necessary DT sources for currently supported
boards. Patch 11 removes board files and code directly related to them,
effectively making s5pv210 a DT-only platform. In next step, patches 12-15
prepare remaining code for multiplatform enablement, which is finally done
in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
unused code left after making the last S5P platform DT-only.
Build tested patch by patch on following configs:
- s3c2410_defconfig (with DT support enabled),
- s3c6400_defconfig (with DT support enabled),
- s5pv210_defconfig (with DT support enabled after patches adding it),
- exynos_defconfig,
- exynos_defconfig with S5PV210 enabled in multiplatform configuration.
Boot tested on s5pv210-goni board.
Note that support for smdkc110, smdkv210 and torbreck boards is provided
by moving data from existing board files to new device tree sources. No
testing was performed due to mentioned board not being available anymore.
However I believe we agreed on this approach, because apparently there
are no active users of them. See the RFC from August 2013 asking for
removal of the whole platform [1].
[1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
Mateusz Krawczuk (6):
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
ARM: s5pv210: Migrate clock handling to Common Clock Framework
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
ARM: s5pv210: Add board file for boot using Device Tree
ARM: Samsung: DT: Add Device tree for s5pv210
ARM: Samsung: DT: Add Device tree for S5PC110/S5PV210 Boards
Tomasz Figa (13):
cpufreq: s3c24xx: Remove some dead code
serial: samsung: Remove support for legacy clock code
ARM: SAMSUNG: Remove legacy clock code
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: S5PV210: Remove support for board files
ARM: S5PV210: Untie PM support from legacy code
ARM: s5pv210: move debug-macro.S into the common space
ARM: s5pv210: Register cpufreq platform device
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: s5pv210: Enable multi-platform build support
gpio: samsung: Remove legacy support of S5PV210
ARM: SAMSUNG: Remove remaining legacy code
clk: samsung: s5pv210: Remove legacy board support
.../bindings/clock/clk-s5pv210-audss.txt | 53 +
.../bindings/clock/samsung,s5pv210-clock.txt | 78 ++
.../devicetree/bindings/phy/samsung-phy.txt | 1 +
arch/arm/Kconfig | 22 +-
arch/arm/Kconfig.debug | 12 +-
arch/arm/Makefile | 4 +-
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/s5pv210-aquila.dts | 392 ++++++
arch/arm/boot/dts/s5pv210-goni.dts | 449 +++++++
arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 839 ++++++++++++
arch/arm/boot/dts/s5pv210-smdkc110.dts | 78 ++
arch/arm/boot/dts/s5pv210-smdkv210.dts | 238 ++++
arch/arm/boot/dts/s5pv210-torbreck.dts | 92 ++
arch/arm/boot/dts/s5pv210.dtsi | 633 +++++++++
arch/arm/include/debug/s5pv210.S | 34 +
arch/arm/mach-exynos/pm.c | 1 -
arch/arm/mach-s3c24xx/common.c | 2 -
arch/arm/mach-s3c24xx/iotiming-s3c2412.c | 1 -
arch/arm/mach-s3c24xx/mach-h1940.c | 5 +-
arch/arm/mach-s3c24xx/mach-jive.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2413.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2416.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2443.c | 1 -
arch/arm/mach-s3c24xx/mach-vstms.c | 1 -
arch/arm/mach-s3c24xx/s3c2410.c | 6 -
arch/arm/mach-s3c24xx/s3c2412.c | 6 -
arch/arm/mach-s3c24xx/s3c2442.c | 1 -
arch/arm/mach-s3c24xx/s3c244x.c | 6 -
arch/arm/mach-s3c64xx/mach-anw6410.c | 1 -
arch/arm/mach-s3c64xx/mach-crag6410.c | 1 -
arch/arm/mach-s3c64xx/mach-hmt.c | 1 -
arch/arm/mach-s3c64xx/mach-ncp.c | 1 -
arch/arm/mach-s3c64xx/mach-smartq.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6400.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6410.c | 1 -
arch/arm/mach-s3c64xx/s3c6400.c | 1 -
arch/arm/mach-s3c64xx/s3c6410.c | 1 -
arch/arm/mach-s5pv210/Kconfig | 197 +--
arch/arm/mach-s5pv210/Makefile | 29 +-
arch/arm/mach-s5pv210/Makefile.boot | 2 -
arch/arm/mach-s5pv210/clock.c | 1365 --------------------
arch/arm/mach-s5pv210/common.c | 279 ----
arch/arm/mach-s5pv210/common.h | 21 +-
arch/arm/mach-s5pv210/dev-audio.c | 246 ----
arch/arm/mach-s5pv210/dma.c | 130 --
arch/arm/mach-s5pv210/include/mach/debug-macro.S | 41 -
arch/arm/mach-s5pv210/include/mach/dma.h | 26 -
arch/arm/mach-s5pv210/include/mach/gpio.h | 140 --
arch/arm/mach-s5pv210/include/mach/hardware.h | 18 -
arch/arm/mach-s5pv210/include/mach/irqs.h | 137 --
arch/arm/mach-s5pv210/include/mach/map.h | 158 ---
arch/arm/mach-s5pv210/include/mach/memory.h | 27 -
arch/arm/mach-s5pv210/include/mach/pm-core.h | 46 -
arch/arm/mach-s5pv210/include/mach/regs-clock.h | 2 +-
arch/arm/mach-s5pv210/include/mach/regs-gpio.h | 41 -
arch/arm/mach-s5pv210/include/mach/regs-irq.h | 18 -
arch/arm/mach-s5pv210/mach-aquila.c | 687 ----------
arch/arm/mach-s5pv210/mach-goni.c | 916 -------------
arch/arm/mach-s5pv210/mach-smdkc110.c | 159 ---
arch/arm/mach-s5pv210/mach-smdkv210.c | 337 -----
arch/arm/mach-s5pv210/mach-torbreck.c | 135 --
arch/arm/mach-s5pv210/pm.c | 147 ++-
arch/arm/mach-s5pv210/s5pv210.c | 77 ++
arch/arm/mach-s5pv210/setup-fb-24bpp.c | 49 -
arch/arm/mach-s5pv210/setup-fimc.c | 43 -
arch/arm/mach-s5pv210/setup-i2c0.c | 28 -
arch/arm/mach-s5pv210/setup-i2c1.c | 28 -
arch/arm/mach-s5pv210/setup-i2c2.c | 28 -
arch/arm/mach-s5pv210/setup-ide.c | 39 -
arch/arm/mach-s5pv210/setup-keypad.c | 24 -
arch/arm/mach-s5pv210/setup-sdhci-gpio.c | 103 --
arch/arm/mach-s5pv210/setup-spi.c | 34 -
arch/arm/mach-s5pv210/setup-usb-phy.c | 95 --
arch/arm/mach-s5pv210/sleep.S | 36 +
arch/arm/plat-samsung/Kconfig | 143 +-
arch/arm/plat-samsung/Makefile | 15 -
arch/arm/plat-samsung/clock-clksrc.c | 212 ---
arch/arm/plat-samsung/clock.c | 539 --------
arch/arm/plat-samsung/cpu.c | 3 +-
arch/arm/plat-samsung/devs.c | 330 -----
arch/arm/plat-samsung/include/plat/camport.h | 28 -
arch/arm/plat-samsung/include/plat/clock-clksrc.h | 83 --
arch/arm/plat-samsung/include/plat/clock.h | 152 ---
arch/arm/plat-samsung/include/plat/cpu-freq-core.h | 3 -
arch/arm/plat-samsung/include/plat/cpu.h | 13 -
arch/arm/plat-samsung/include/plat/devs.h | 42 -
arch/arm/plat-samsung/include/plat/fb-core.h | 15 -
arch/arm/plat-samsung/include/plat/fb.h | 22 -
arch/arm/plat-samsung/include/plat/fimc-core.h | 51 -
arch/arm/plat-samsung/include/plat/gpio-cfg.h | 64 -
arch/arm/plat-samsung/include/plat/hdmi.h | 16 -
arch/arm/plat-samsung/include/plat/irqs.h | 72 --
arch/arm/plat-samsung/include/plat/mfc.h | 35 -
arch/arm/plat-samsung/include/plat/pll.h | 323 -----
arch/arm/plat-samsung/include/plat/s5p-clock.h | 65 -
arch/arm/plat-samsung/include/plat/sdhci.h | 47 -
arch/arm/plat-samsung/include/plat/tv-core.h | 44 -
arch/arm/plat-samsung/init.c | 1 -
arch/arm/plat-samsung/pm-gpio.c | 4 +-
arch/arm/plat-samsung/s5p-clock.c | 294 -----
arch/arm/plat-samsung/s5p-dev-mfc.c | 81 +-
arch/arm/plat-samsung/s5p-dev-uart.c | 88 --
arch/arm/plat-samsung/s5p-irq-eint.c | 221 ----
arch/arm/plat-samsung/s5p-irq-gpioint.c | 218 ----
arch/arm/plat-samsung/s5p-irq-pm.c | 92 --
arch/arm/plat-samsung/s5p-irq.c | 31 -
arch/arm/plat-samsung/s5p-pm.c | 40 -
arch/arm/plat-samsung/s5p-sleep.S | 45 -
drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-s5pv210-audss.c | 241 ++++
drivers/clk/samsung/clk-s5pv210.c | 856 ++++++++++++
drivers/cpufreq/s3c2410-cpufreq.c | 2 -
drivers/cpufreq/s3c2412-cpufreq.c | 3 -
drivers/cpufreq/s3c2440-cpufreq.c | 3 -
drivers/cpufreq/s3c24xx-cpufreq.c | 1 -
drivers/cpufreq/s5pv210-cpufreq.c | 131 +-
drivers/gpio/gpio-samsung.c | 240 ----
drivers/phy/Kconfig | 10 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-s5pv210-usb2.c | 187 +++
drivers/phy/phy-samsung-usb2.c | 6 +
drivers/phy/phy-samsung-usb2.h | 1 +
drivers/tty/serial/samsung.c | 4 -
include/dt-bindings/clock/s5pv210-audss.h | 34 +
include/dt-bindings/clock/s5pv210.h | 239 ++++
125 files changed, 4843 insertions(+), 9409 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt
create mode 100644 Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt
create mode 100644 arch/arm/boot/dts/s5pv210-aquila.dts
create mode 100644 arch/arm/boot/dts/s5pv210-goni.dts
create mode 100644 arch/arm/boot/dts/s5pv210-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/s5pv210-smdkc110.dts
create mode 100644 arch/arm/boot/dts/s5pv210-smdkv210.dts
create mode 100644 arch/arm/boot/dts/s5pv210-torbreck.dts
create mode 100644 arch/arm/boot/dts/s5pv210.dtsi
create mode 100644 arch/arm/include/debug/s5pv210.S
delete mode 100644 arch/arm/mach-s5pv210/Makefile.boot
delete mode 100644 arch/arm/mach-s5pv210/clock.c
delete mode 100644 arch/arm/mach-s5pv210/common.c
delete mode 100644 arch/arm/mach-s5pv210/dev-audio.c
delete mode 100644 arch/arm/mach-s5pv210/dma.c
delete mode 100644 arch/arm/mach-s5pv210/include/mach/debug-macro.S
delete mode 100644 arch/arm/mach-s5pv210/include/mach/dma.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/hardware.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/irqs.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/map.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/memory.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/pm-core.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-irq.h
delete mode 100644 arch/arm/mach-s5pv210/mach-aquila.c
delete mode 100644 arch/arm/mach-s5pv210/mach-goni.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkc110.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkv210.c
delete mode 100644 arch/arm/mach-s5pv210/mach-torbreck.c
create mode 100644 arch/arm/mach-s5pv210/s5pv210.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fb-24bpp.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fimc.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c0.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c1.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c2.c
delete mode 100644 arch/arm/mach-s5pv210/setup-ide.c
delete mode 100644 arch/arm/mach-s5pv210/setup-keypad.c
delete mode 100644 arch/arm/mach-s5pv210/setup-sdhci-gpio.c
delete mode 100644 arch/arm/mach-s5pv210/setup-spi.c
delete mode 100644 arch/arm/mach-s5pv210/setup-usb-phy.c
create mode 100644 arch/arm/mach-s5pv210/sleep.S
delete mode 100644 arch/arm/plat-samsung/clock-clksrc.c
delete mode 100644 arch/arm/plat-samsung/clock.c
delete mode 100644 arch/arm/plat-samsung/include/plat/camport.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock-clksrc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/fimc-core.h
delete mode 100644 arch/arm/plat-samsung/include/plat/hdmi.h
delete mode 100644 arch/arm/plat-samsung/include/plat/irqs.h
delete mode 100644 arch/arm/plat-samsung/include/plat/mfc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/pll.h
delete mode 100644 arch/arm/plat-samsung/include/plat/s5p-clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/tv-core.h
delete mode 100644 arch/arm/plat-samsung/s5p-clock.c
delete mode 100644 arch/arm/plat-samsung/s5p-dev-uart.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-eint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-gpioint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq.c
delete mode 100644 arch/arm/plat-samsung/s5p-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-sleep.S
create mode 100644 drivers/clk/samsung/clk-s5pv210-audss.c
create mode 100644 drivers/clk/samsung/clk-s5pv210.c
create mode 100644 drivers/phy/phy-s5pv210-usb2.c
create mode 100644 include/dt-bindings/clock/s5pv210-audss.h
create mode 100644 include/dt-bindings/clock/s5pv210.h
--
1.9.3
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-04 17:44 ` Tomasz Figa
0 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-04 17:44 UTC (permalink / raw)
To: linux-arm-kernel
This huge series is a (hopefully final) attempt to convert Samsung S5PV210
into a DT-only and multiplatform-aware platform. It consists of several
steps to gradually replace legacy code with one meeting current standards
and then finally remove unused remnants.
Patches 1-6 migrate the platform to fully use the Common Clock Framework
and get rid of legacy private clock code, of which s5pv210 was the last
user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
USB to be supported when using DT. Further three patches (8-10) add DT
support for mach-s5pv210 and necessary DT sources for currently supported
boards. Patch 11 removes board files and code directly related to them,
effectively making s5pv210 a DT-only platform. In next step, patches 12-15
prepare remaining code for multiplatform enablement, which is finally done
in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
unused code left after making the last S5P platform DT-only.
Build tested patch by patch on following configs:
- s3c2410_defconfig (with DT support enabled),
- s3c6400_defconfig (with DT support enabled),
- s5pv210_defconfig (with DT support enabled after patches adding it),
- exynos_defconfig,
- exynos_defconfig with S5PV210 enabled in multiplatform configuration.
Boot tested on s5pv210-goni board.
Note that support for smdkc110, smdkv210 and torbreck boards is provided
by moving data from existing board files to new device tree sources. No
testing was performed due to mentioned board not being available anymore.
However I believe we agreed on this approach, because apparently there
are no active users of them. See the RFC from August 2013 asking for
removal of the whole platform [1].
[1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
Mateusz Krawczuk (6):
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
ARM: s5pv210: Migrate clock handling to Common Clock Framework
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
ARM: s5pv210: Add board file for boot using Device Tree
ARM: Samsung: DT: Add Device tree for s5pv210
ARM: Samsung: DT: Add Device tree for S5PC110/S5PV210 Boards
Tomasz Figa (13):
cpufreq: s3c24xx: Remove some dead code
serial: samsung: Remove support for legacy clock code
ARM: SAMSUNG: Remove legacy clock code
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: S5PV210: Remove support for board files
ARM: S5PV210: Untie PM support from legacy code
ARM: s5pv210: move debug-macro.S into the common space
ARM: s5pv210: Register cpufreq platform device
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: s5pv210: Enable multi-platform build support
gpio: samsung: Remove legacy support of S5PV210
ARM: SAMSUNG: Remove remaining legacy code
clk: samsung: s5pv210: Remove legacy board support
.../bindings/clock/clk-s5pv210-audss.txt | 53 +
.../bindings/clock/samsung,s5pv210-clock.txt | 78 ++
.../devicetree/bindings/phy/samsung-phy.txt | 1 +
arch/arm/Kconfig | 22 +-
arch/arm/Kconfig.debug | 12 +-
arch/arm/Makefile | 4 +-
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/s5pv210-aquila.dts | 392 ++++++
arch/arm/boot/dts/s5pv210-goni.dts | 449 +++++++
arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 839 ++++++++++++
arch/arm/boot/dts/s5pv210-smdkc110.dts | 78 ++
arch/arm/boot/dts/s5pv210-smdkv210.dts | 238 ++++
arch/arm/boot/dts/s5pv210-torbreck.dts | 92 ++
arch/arm/boot/dts/s5pv210.dtsi | 633 +++++++++
arch/arm/include/debug/s5pv210.S | 34 +
arch/arm/mach-exynos/pm.c | 1 -
arch/arm/mach-s3c24xx/common.c | 2 -
arch/arm/mach-s3c24xx/iotiming-s3c2412.c | 1 -
arch/arm/mach-s3c24xx/mach-h1940.c | 5 +-
arch/arm/mach-s3c24xx/mach-jive.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2413.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2416.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2443.c | 1 -
arch/arm/mach-s3c24xx/mach-vstms.c | 1 -
arch/arm/mach-s3c24xx/s3c2410.c | 6 -
arch/arm/mach-s3c24xx/s3c2412.c | 6 -
arch/arm/mach-s3c24xx/s3c2442.c | 1 -
arch/arm/mach-s3c24xx/s3c244x.c | 6 -
arch/arm/mach-s3c64xx/mach-anw6410.c | 1 -
arch/arm/mach-s3c64xx/mach-crag6410.c | 1 -
arch/arm/mach-s3c64xx/mach-hmt.c | 1 -
arch/arm/mach-s3c64xx/mach-ncp.c | 1 -
arch/arm/mach-s3c64xx/mach-smartq.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6400.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6410.c | 1 -
arch/arm/mach-s3c64xx/s3c6400.c | 1 -
arch/arm/mach-s3c64xx/s3c6410.c | 1 -
arch/arm/mach-s5pv210/Kconfig | 197 +--
arch/arm/mach-s5pv210/Makefile | 29 +-
arch/arm/mach-s5pv210/Makefile.boot | 2 -
arch/arm/mach-s5pv210/clock.c | 1365 --------------------
arch/arm/mach-s5pv210/common.c | 279 ----
arch/arm/mach-s5pv210/common.h | 21 +-
arch/arm/mach-s5pv210/dev-audio.c | 246 ----
arch/arm/mach-s5pv210/dma.c | 130 --
arch/arm/mach-s5pv210/include/mach/debug-macro.S | 41 -
arch/arm/mach-s5pv210/include/mach/dma.h | 26 -
arch/arm/mach-s5pv210/include/mach/gpio.h | 140 --
arch/arm/mach-s5pv210/include/mach/hardware.h | 18 -
arch/arm/mach-s5pv210/include/mach/irqs.h | 137 --
arch/arm/mach-s5pv210/include/mach/map.h | 158 ---
arch/arm/mach-s5pv210/include/mach/memory.h | 27 -
arch/arm/mach-s5pv210/include/mach/pm-core.h | 46 -
arch/arm/mach-s5pv210/include/mach/regs-clock.h | 2 +-
arch/arm/mach-s5pv210/include/mach/regs-gpio.h | 41 -
arch/arm/mach-s5pv210/include/mach/regs-irq.h | 18 -
arch/arm/mach-s5pv210/mach-aquila.c | 687 ----------
arch/arm/mach-s5pv210/mach-goni.c | 916 -------------
arch/arm/mach-s5pv210/mach-smdkc110.c | 159 ---
arch/arm/mach-s5pv210/mach-smdkv210.c | 337 -----
arch/arm/mach-s5pv210/mach-torbreck.c | 135 --
arch/arm/mach-s5pv210/pm.c | 147 ++-
arch/arm/mach-s5pv210/s5pv210.c | 77 ++
arch/arm/mach-s5pv210/setup-fb-24bpp.c | 49 -
arch/arm/mach-s5pv210/setup-fimc.c | 43 -
arch/arm/mach-s5pv210/setup-i2c0.c | 28 -
arch/arm/mach-s5pv210/setup-i2c1.c | 28 -
arch/arm/mach-s5pv210/setup-i2c2.c | 28 -
arch/arm/mach-s5pv210/setup-ide.c | 39 -
arch/arm/mach-s5pv210/setup-keypad.c | 24 -
arch/arm/mach-s5pv210/setup-sdhci-gpio.c | 103 --
arch/arm/mach-s5pv210/setup-spi.c | 34 -
arch/arm/mach-s5pv210/setup-usb-phy.c | 95 --
arch/arm/mach-s5pv210/sleep.S | 36 +
arch/arm/plat-samsung/Kconfig | 143 +-
arch/arm/plat-samsung/Makefile | 15 -
arch/arm/plat-samsung/clock-clksrc.c | 212 ---
arch/arm/plat-samsung/clock.c | 539 --------
arch/arm/plat-samsung/cpu.c | 3 +-
arch/arm/plat-samsung/devs.c | 330 -----
arch/arm/plat-samsung/include/plat/camport.h | 28 -
arch/arm/plat-samsung/include/plat/clock-clksrc.h | 83 --
arch/arm/plat-samsung/include/plat/clock.h | 152 ---
arch/arm/plat-samsung/include/plat/cpu-freq-core.h | 3 -
arch/arm/plat-samsung/include/plat/cpu.h | 13 -
arch/arm/plat-samsung/include/plat/devs.h | 42 -
arch/arm/plat-samsung/include/plat/fb-core.h | 15 -
arch/arm/plat-samsung/include/plat/fb.h | 22 -
arch/arm/plat-samsung/include/plat/fimc-core.h | 51 -
arch/arm/plat-samsung/include/plat/gpio-cfg.h | 64 -
arch/arm/plat-samsung/include/plat/hdmi.h | 16 -
arch/arm/plat-samsung/include/plat/irqs.h | 72 --
arch/arm/plat-samsung/include/plat/mfc.h | 35 -
arch/arm/plat-samsung/include/plat/pll.h | 323 -----
arch/arm/plat-samsung/include/plat/s5p-clock.h | 65 -
arch/arm/plat-samsung/include/plat/sdhci.h | 47 -
arch/arm/plat-samsung/include/plat/tv-core.h | 44 -
arch/arm/plat-samsung/init.c | 1 -
arch/arm/plat-samsung/pm-gpio.c | 4 +-
arch/arm/plat-samsung/s5p-clock.c | 294 -----
arch/arm/plat-samsung/s5p-dev-mfc.c | 81 +-
arch/arm/plat-samsung/s5p-dev-uart.c | 88 --
arch/arm/plat-samsung/s5p-irq-eint.c | 221 ----
arch/arm/plat-samsung/s5p-irq-gpioint.c | 218 ----
arch/arm/plat-samsung/s5p-irq-pm.c | 92 --
arch/arm/plat-samsung/s5p-irq.c | 31 -
arch/arm/plat-samsung/s5p-pm.c | 40 -
arch/arm/plat-samsung/s5p-sleep.S | 45 -
drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-s5pv210-audss.c | 241 ++++
drivers/clk/samsung/clk-s5pv210.c | 856 ++++++++++++
drivers/cpufreq/s3c2410-cpufreq.c | 2 -
drivers/cpufreq/s3c2412-cpufreq.c | 3 -
drivers/cpufreq/s3c2440-cpufreq.c | 3 -
drivers/cpufreq/s3c24xx-cpufreq.c | 1 -
drivers/cpufreq/s5pv210-cpufreq.c | 131 +-
drivers/gpio/gpio-samsung.c | 240 ----
drivers/phy/Kconfig | 10 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-s5pv210-usb2.c | 187 +++
drivers/phy/phy-samsung-usb2.c | 6 +
drivers/phy/phy-samsung-usb2.h | 1 +
drivers/tty/serial/samsung.c | 4 -
include/dt-bindings/clock/s5pv210-audss.h | 34 +
include/dt-bindings/clock/s5pv210.h | 239 ++++
125 files changed, 4843 insertions(+), 9409 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt
create mode 100644 Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt
create mode 100644 arch/arm/boot/dts/s5pv210-aquila.dts
create mode 100644 arch/arm/boot/dts/s5pv210-goni.dts
create mode 100644 arch/arm/boot/dts/s5pv210-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/s5pv210-smdkc110.dts
create mode 100644 arch/arm/boot/dts/s5pv210-smdkv210.dts
create mode 100644 arch/arm/boot/dts/s5pv210-torbreck.dts
create mode 100644 arch/arm/boot/dts/s5pv210.dtsi
create mode 100644 arch/arm/include/debug/s5pv210.S
delete mode 100644 arch/arm/mach-s5pv210/Makefile.boot
delete mode 100644 arch/arm/mach-s5pv210/clock.c
delete mode 100644 arch/arm/mach-s5pv210/common.c
delete mode 100644 arch/arm/mach-s5pv210/dev-audio.c
delete mode 100644 arch/arm/mach-s5pv210/dma.c
delete mode 100644 arch/arm/mach-s5pv210/include/mach/debug-macro.S
delete mode 100644 arch/arm/mach-s5pv210/include/mach/dma.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/hardware.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/irqs.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/map.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/memory.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/pm-core.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-irq.h
delete mode 100644 arch/arm/mach-s5pv210/mach-aquila.c
delete mode 100644 arch/arm/mach-s5pv210/mach-goni.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkc110.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkv210.c
delete mode 100644 arch/arm/mach-s5pv210/mach-torbreck.c
create mode 100644 arch/arm/mach-s5pv210/s5pv210.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fb-24bpp.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fimc.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c0.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c1.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c2.c
delete mode 100644 arch/arm/mach-s5pv210/setup-ide.c
delete mode 100644 arch/arm/mach-s5pv210/setup-keypad.c
delete mode 100644 arch/arm/mach-s5pv210/setup-sdhci-gpio.c
delete mode 100644 arch/arm/mach-s5pv210/setup-spi.c
delete mode 100644 arch/arm/mach-s5pv210/setup-usb-phy.c
create mode 100644 arch/arm/mach-s5pv210/sleep.S
delete mode 100644 arch/arm/plat-samsung/clock-clksrc.c
delete mode 100644 arch/arm/plat-samsung/clock.c
delete mode 100644 arch/arm/plat-samsung/include/plat/camport.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock-clksrc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/fimc-core.h
delete mode 100644 arch/arm/plat-samsung/include/plat/hdmi.h
delete mode 100644 arch/arm/plat-samsung/include/plat/irqs.h
delete mode 100644 arch/arm/plat-samsung/include/plat/mfc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/pll.h
delete mode 100644 arch/arm/plat-samsung/include/plat/s5p-clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/tv-core.h
delete mode 100644 arch/arm/plat-samsung/s5p-clock.c
delete mode 100644 arch/arm/plat-samsung/s5p-dev-uart.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-eint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-gpioint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq.c
delete mode 100644 arch/arm/plat-samsung/s5p-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-sleep.S
create mode 100644 drivers/clk/samsung/clk-s5pv210-audss.c
create mode 100644 drivers/clk/samsung/clk-s5pv210.c
create mode 100644 drivers/phy/phy-s5pv210-usb2.c
create mode 100644 include/dt-bindings/clock/s5pv210-audss.h
create mode 100644 include/dt-bindings/clock/s5pv210.h
--
1.9.3
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
2014-07-04 17:44 ` Tomasz Figa
@ 2014-07-05 4:46 ` Viresh Kumar
-1 siblings, 0 replies; 19+ messages in thread
From: Viresh Kumar @ 2014-07-05 4:46 UTC (permalink / raw)
To: Tomasz Figa
Cc: linux-samsung-soc, Kukjin Kim, Heiko Stübner, Arnd Bergmann,
linux-kernel, Tomasz Figa, Mark Brown, Olof Johansson,
linux-arm-kernel, Marek Szyprowski, Rafael J. Wysocki
On Fri, Jul 4, 2014 at 11:14 PM, Tomasz Figa <t.figa@samsung.com> wrote:
> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
> into a DT-only and multiplatform-aware platform. It consists of several
> steps to gradually replace legacy code with one meeting current standards
> and then finally remove unused remnants.
>
> Patches 1-6 migrate the platform to fully use the Common Clock Framework
> and get rid of legacy private clock code, of which s5pv210 was the last
> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
> USB to be supported when using DT. Further three patches (8-10) add DT
> support for mach-s5pv210 and necessary DT sources for currently supported
> boards. Patch 11 removes board files and code directly related to them,
> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
> prepare remaining code for multiplatform enablement, which is finally done
> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
> unused code left after making the last S5P platform DT-only.
>
> Build tested patch by patch on following configs:
> - s3c2410_defconfig (with DT support enabled),
> - s3c6400_defconfig (with DT support enabled),
> - s5pv210_defconfig (with DT support enabled after patches adding it),
> - exynos_defconfig,
> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>
> Boot tested on s5pv210-goni board.
>
> Note that support for smdkc110, smdkv210 and torbreck boards is provided
> by moving data from existing board files to new device tree sources. No
> testing was performed due to mentioned board not being available anymore.
> However I believe we agreed on this approach, because apparently there
> are no active users of them. See the RFC from August 2013 asking for
> removal of the whole platform [1].
>
> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
> Tomasz Figa (13):
> cpufreq: s3c24xx: Remove some dead code
> cpufreq: s5pv210: Make the driver multiplatform aware
Looks like you used --suppress-cc=all while sending these and none of
CPUFreq/PM guys received it :(
Anyways, for cpufreq part:
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-05 4:46 ` Viresh Kumar
0 siblings, 0 replies; 19+ messages in thread
From: Viresh Kumar @ 2014-07-05 4:46 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jul 4, 2014 at 11:14 PM, Tomasz Figa <t.figa@samsung.com> wrote:
> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
> into a DT-only and multiplatform-aware platform. It consists of several
> steps to gradually replace legacy code with one meeting current standards
> and then finally remove unused remnants.
>
> Patches 1-6 migrate the platform to fully use the Common Clock Framework
> and get rid of legacy private clock code, of which s5pv210 was the last
> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
> USB to be supported when using DT. Further three patches (8-10) add DT
> support for mach-s5pv210 and necessary DT sources for currently supported
> boards. Patch 11 removes board files and code directly related to them,
> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
> prepare remaining code for multiplatform enablement, which is finally done
> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
> unused code left after making the last S5P platform DT-only.
>
> Build tested patch by patch on following configs:
> - s3c2410_defconfig (with DT support enabled),
> - s3c6400_defconfig (with DT support enabled),
> - s5pv210_defconfig (with DT support enabled after patches adding it),
> - exynos_defconfig,
> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>
> Boot tested on s5pv210-goni board.
>
> Note that support for smdkc110, smdkv210 and torbreck boards is provided
> by moving data from existing board files to new device tree sources. No
> testing was performed due to mentioned board not being available anymore.
> However I believe we agreed on this approach, because apparently there
> are no active users of them. See the RFC from August 2013 asking for
> removal of the whole platform [1].
>
> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
> Tomasz Figa (13):
> cpufreq: s3c24xx: Remove some dead code
> cpufreq: s5pv210: Make the driver multiplatform aware
Looks like you used --suppress-cc=all while sending these and none of
CPUFreq/PM guys received it :(
Anyways, for cpufreq part:
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
2014-07-05 4:46 ` Viresh Kumar
@ 2014-07-05 11:00 ` Tomasz Figa
-1 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-05 11:00 UTC (permalink / raw)
To: Viresh Kumar, Tomasz Figa
Cc: linux-samsung-soc, Kukjin Kim, Heiko Stübner, Arnd Bergmann,
linux-kernel, Mark Brown, Olof Johansson, linux-arm-kernel,
Marek Szyprowski, Rafael J. Wysocki
On 05.07.2014 06:46, Viresh Kumar wrote:
> On Fri, Jul 4, 2014 at 11:14 PM, Tomasz Figa <t.figa@samsung.com> wrote:
>> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
>> into a DT-only and multiplatform-aware platform. It consists of several
>> steps to gradually replace legacy code with one meeting current standards
>> and then finally remove unused remnants.
>>
>> Patches 1-6 migrate the platform to fully use the Common Clock Framework
>> and get rid of legacy private clock code, of which s5pv210 was the last
>> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
>> USB to be supported when using DT. Further three patches (8-10) add DT
>> support for mach-s5pv210 and necessary DT sources for currently supported
>> boards. Patch 11 removes board files and code directly related to them,
>> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
>> prepare remaining code for multiplatform enablement, which is finally done
>> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
>> unused code left after making the last S5P platform DT-only.
>>
>> Build tested patch by patch on following configs:
>> - s3c2410_defconfig (with DT support enabled),
>> - s3c6400_defconfig (with DT support enabled),
>> - s5pv210_defconfig (with DT support enabled after patches adding it),
>> - exynos_defconfig,
>> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>>
>> Boot tested on s5pv210-goni board.
>>
>> Note that support for smdkc110, smdkv210 and torbreck boards is provided
>> by moving data from existing board files to new device tree sources. No
>> testing was performed due to mentioned board not being available anymore.
>> However I believe we agreed on this approach, because apparently there
>> are no active users of them. See the RFC from August 2013 asking for
>> removal of the whole platform [1].
>>
>> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
>
>> Tomasz Figa (13):
>> cpufreq: s3c24xx: Remove some dead code
>> cpufreq: s5pv210: Make the driver multiplatform aware
>
> Looks like you used --suppress-cc=all while sending these and none of
> CPUFreq/PM guys received it :(
Oops, I had a feeling that I has screwed up something with this series
and now we know what. Sorry for this. Will resend properly next Tuesday.
>
> Anyways, for cpufreq part:
>
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
>
Thanks. Will add to the patches when resending.
Best regards,
Tomasz
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-05 11:00 ` Tomasz Figa
0 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-05 11:00 UTC (permalink / raw)
To: linux-arm-kernel
On 05.07.2014 06:46, Viresh Kumar wrote:
> On Fri, Jul 4, 2014 at 11:14 PM, Tomasz Figa <t.figa@samsung.com> wrote:
>> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
>> into a DT-only and multiplatform-aware platform. It consists of several
>> steps to gradually replace legacy code with one meeting current standards
>> and then finally remove unused remnants.
>>
>> Patches 1-6 migrate the platform to fully use the Common Clock Framework
>> and get rid of legacy private clock code, of which s5pv210 was the last
>> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
>> USB to be supported when using DT. Further three patches (8-10) add DT
>> support for mach-s5pv210 and necessary DT sources for currently supported
>> boards. Patch 11 removes board files and code directly related to them,
>> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
>> prepare remaining code for multiplatform enablement, which is finally done
>> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
>> unused code left after making the last S5P platform DT-only.
>>
>> Build tested patch by patch on following configs:
>> - s3c2410_defconfig (with DT support enabled),
>> - s3c6400_defconfig (with DT support enabled),
>> - s5pv210_defconfig (with DT support enabled after patches adding it),
>> - exynos_defconfig,
>> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>>
>> Boot tested on s5pv210-goni board.
>>
>> Note that support for smdkc110, smdkv210 and torbreck boards is provided
>> by moving data from existing board files to new device tree sources. No
>> testing was performed due to mentioned board not being available anymore.
>> However I believe we agreed on this approach, because apparently there
>> are no active users of them. See the RFC from August 2013 asking for
>> removal of the whole platform [1].
>>
>> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
>
>> Tomasz Figa (13):
>> cpufreq: s3c24xx: Remove some dead code
>> cpufreq: s5pv210: Make the driver multiplatform aware
>
> Looks like you used --suppress-cc=all while sending these and none of
> CPUFreq/PM guys received it :(
Oops, I had a feeling that I has screwed up something with this series
and now we know what. Sorry for this. Will resend properly next Tuesday.
>
> Anyways, for cpufreq part:
>
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
>
Thanks. Will add to the patches when resending.
Best regards,
Tomasz
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
2014-07-05 11:00 ` Tomasz Figa
(?)
@ 2014-07-05 11:05 ` Heiko Stübner
-1 siblings, 0 replies; 19+ messages in thread
From: Heiko Stübner @ 2014-07-05 11:05 UTC (permalink / raw)
To: Tomasz Figa
Cc: Viresh Kumar, Tomasz Figa, linux-samsung-soc, Kukjin Kim,
Arnd Bergmann, linux-kernel, Mark Brown, Olof Johansson,
linux-arm-kernel, Marek Szyprowski, Rafael J. Wysocki
Am Samstag, 5. Juli 2014, 13:00:43 schrieb Tomasz Figa:
> On 05.07.2014 06:46, Viresh Kumar wrote:
> > On Fri, Jul 4, 2014 at 11:14 PM, Tomasz Figa <t.figa@samsung.com> wrote:
> >> This huge series is a (hopefully final) attempt to convert Samsung
> >> S5PV210
> >> into a DT-only and multiplatform-aware platform. It consists of several
> >> steps to gradually replace legacy code with one meeting current standards
> >> and then finally remove unused remnants.
> >>
> >> Patches 1-6 migrate the platform to fully use the Common Clock Framework
> >> and get rid of legacy private clock code, of which s5pv210 was the last
> >> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to
> >> allow
> >> USB to be supported when using DT. Further three patches (8-10) add DT
> >> support for mach-s5pv210 and necessary DT sources for currently supported
> >> boards. Patch 11 removes board files and code directly related to them,
> >> effectively making s5pv210 a DT-only platform. In next step, patches
> >> 12-15
> >> prepare remaining code for multiplatform enablement, which is finally
> >> done
> >> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
> >> unused code left after making the last S5P platform DT-only.
> >>
> >> Build tested patch by patch on following configs:
> >> - s3c2410_defconfig (with DT support enabled),
> >> - s3c6400_defconfig (with DT support enabled),
> >> - s5pv210_defconfig (with DT support enabled after patches adding it),
> >> - exynos_defconfig,
> >> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
> >>
> >> Boot tested on s5pv210-goni board.
> >>
> >> Note that support for smdkc110, smdkv210 and torbreck boards is provided
> >> by moving data from existing board files to new device tree sources. No
> >> testing was performed due to mentioned board not being available anymore.
> >> However I believe we agreed on this approach, because apparently there
> >> are no active users of them. See the RFC from August 2013 asking for
> >> removal of the whole platform [1].
> >>
> >> [1]
> >> http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882
> >> .html>>
> >> Tomasz Figa (13):
> >> cpufreq: s3c24xx: Remove some dead code
> >> cpufreq: s5pv210: Make the driver multiplatform aware
> >
> > Looks like you used --suppress-cc=all while sending these and none of
> > CPUFreq/PM guys received it :(
>
> Oops, I had a feeling that I has screwed up something with this series
> and now we know what. Sorry for this. Will resend properly next Tuesday.
I got the cover-letter 3 times (19:44, 19:46 and 19:48). The one from 19:48
also did contain all 19 patches ;-)
Heiko
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-05 11:05 ` Heiko Stübner
0 siblings, 0 replies; 19+ messages in thread
From: Heiko Stübner @ 2014-07-05 11:05 UTC (permalink / raw)
To: Tomasz Figa
Cc: Viresh Kumar, Tomasz Figa, linux-samsung-soc, Kukjin Kim,
Arnd Bergmann, linux-kernel, Mark Brown, Olof Johansson,
linux-arm-kernel, Marek Szyprowski, Rafael J. Wysocki
Am Samstag, 5. Juli 2014, 13:00:43 schrieb Tomasz Figa:
> On 05.07.2014 06:46, Viresh Kumar wrote:
> > On Fri, Jul 4, 2014 at 11:14 PM, Tomasz Figa <t.figa@samsung.com> wrote:
> >> This huge series is a (hopefully final) attempt to convert Samsung
> >> S5PV210
> >> into a DT-only and multiplatform-aware platform. It consists of several
> >> steps to gradually replace legacy code with one meeting current standards
> >> and then finally remove unused remnants.
> >>
> >> Patches 1-6 migrate the platform to fully use the Common Clock Framework
> >> and get rid of legacy private clock code, of which s5pv210 was the last
> >> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to
> >> allow
> >> USB to be supported when using DT. Further three patches (8-10) add DT
> >> support for mach-s5pv210 and necessary DT sources for currently supported
> >> boards. Patch 11 removes board files and code directly related to them,
> >> effectively making s5pv210 a DT-only platform. In next step, patches
> >> 12-15
> >> prepare remaining code for multiplatform enablement, which is finally
> >> done
> >> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
> >> unused code left after making the last S5P platform DT-only.
> >>
> >> Build tested patch by patch on following configs:
> >> - s3c2410_defconfig (with DT support enabled),
> >> - s3c6400_defconfig (with DT support enabled),
> >> - s5pv210_defconfig (with DT support enabled after patches adding it),
> >> - exynos_defconfig,
> >> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
> >>
> >> Boot tested on s5pv210-goni board.
> >>
> >> Note that support for smdkc110, smdkv210 and torbreck boards is provided
> >> by moving data from existing board files to new device tree sources. No
> >> testing was performed due to mentioned board not being available anymore.
> >> However I believe we agreed on this approach, because apparently there
> >> are no active users of them. See the RFC from August 2013 asking for
> >> removal of the whole platform [1].
> >>
> >> [1]
> >> http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882
> >> .html>>
> >> Tomasz Figa (13):
> >> cpufreq: s3c24xx: Remove some dead code
> >> cpufreq: s5pv210: Make the driver multiplatform aware
> >
> > Looks like you used --suppress-cc=all while sending these and none of
> > CPUFreq/PM guys received it :(
>
> Oops, I had a feeling that I has screwed up something with this series
> and now we know what. Sorry for this. Will resend properly next Tuesday.
I got the cover-letter 3 times (19:44, 19:46 and 19:48). The one from 19:48
also did contain all 19 patches ;-)
Heiko
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-05 11:05 ` Heiko Stübner
0 siblings, 0 replies; 19+ messages in thread
From: Heiko Stübner @ 2014-07-05 11:05 UTC (permalink / raw)
To: linux-arm-kernel
Am Samstag, 5. Juli 2014, 13:00:43 schrieb Tomasz Figa:
> On 05.07.2014 06:46, Viresh Kumar wrote:
> > On Fri, Jul 4, 2014 at 11:14 PM, Tomasz Figa <t.figa@samsung.com> wrote:
> >> This huge series is a (hopefully final) attempt to convert Samsung
> >> S5PV210
> >> into a DT-only and multiplatform-aware platform. It consists of several
> >> steps to gradually replace legacy code with one meeting current standards
> >> and then finally remove unused remnants.
> >>
> >> Patches 1-6 migrate the platform to fully use the Common Clock Framework
> >> and get rid of legacy private clock code, of which s5pv210 was the last
> >> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to
> >> allow
> >> USB to be supported when using DT. Further three patches (8-10) add DT
> >> support for mach-s5pv210 and necessary DT sources for currently supported
> >> boards. Patch 11 removes board files and code directly related to them,
> >> effectively making s5pv210 a DT-only platform. In next step, patches
> >> 12-15
> >> prepare remaining code for multiplatform enablement, which is finally
> >> done
> >> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
> >> unused code left after making the last S5P platform DT-only.
> >>
> >> Build tested patch by patch on following configs:
> >> - s3c2410_defconfig (with DT support enabled),
> >> - s3c6400_defconfig (with DT support enabled),
> >> - s5pv210_defconfig (with DT support enabled after patches adding it),
> >> - exynos_defconfig,
> >> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
> >>
> >> Boot tested on s5pv210-goni board.
> >>
> >> Note that support for smdkc110, smdkv210 and torbreck boards is provided
> >> by moving data from existing board files to new device tree sources. No
> >> testing was performed due to mentioned board not being available anymore.
> >> However I believe we agreed on this approach, because apparently there
> >> are no active users of them. See the RFC from August 2013 asking for
> >> removal of the whole platform [1].
> >>
> >> [1]
> >> http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882
> >> .html>>
> >> Tomasz Figa (13):
> >> cpufreq: s3c24xx: Remove some dead code
> >> cpufreq: s5pv210: Make the driver multiplatform aware
> >
> > Looks like you used --suppress-cc=all while sending these and none of
> > CPUFreq/PM guys received it :(
>
> Oops, I had a feeling that I has screwed up something with this series
> and now we know what. Sorry for this. Will resend properly next Tuesday.
I got the cover-letter 3 times (19:44, 19:46 and 19:48). The one from 19:48
also did contain all 19 patches ;-)
Heiko
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
2014-07-04 20:15 ` Arnd Bergmann
@ 2014-07-12 22:57 ` Kukjin Kim
-1 siblings, 0 replies; 19+ messages in thread
From: Kukjin Kim @ 2014-07-12 22:57 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Tomasz Figa, linux-samsung-soc, Kukjin Kim,
Heiko Stübner, linux-kernel, Tomasz Figa, Mark Brown,
Olof Johansson, Marek Szyprowski
On 07/05/14 05:15, Arnd Bergmann wrote:
> On Friday 04 July 2014 19:48:00 Tomasz Figa wrote:
>> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
>> into a DT-only and multiplatform-aware platform. It consists of several
>> steps to gradually replace legacy code with one meeting current standards
>> and then finally remove unused remnants.
>>
>> Patches 1-6 migrate the platform to fully use the Common Clock Framework
>> and get rid of legacy private clock code, of which s5pv210 was the last
>> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
>> USB to be supported when using DT. Further three patches (8-10) add DT
>> support for mach-s5pv210 and necessary DT sources for currently supported
>> boards. Patch 11 removes board files and code directly related to them,
>> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
>> prepare remaining code for multiplatform enablement, which is finally done
>> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
>> unused code left after making the last S5P platform DT-only.
>>
>> Build tested patch by patch on following configs:
>> - s3c2410_defconfig (with DT support enabled),
>> - s3c6400_defconfig (with DT support enabled),
>> - s5pv210_defconfig (with DT support enabled after patches adding it),
>> - exynos_defconfig,
>> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>>
>> Boot tested on s5pv210-goni board.
>>
>> Note that support for smdkc110, smdkv210 and torbreck boards is provided
>> by moving data from existing board files to new device tree sources. No
>> testing was performed due to mentioned board not being available anymore.
>> However I believe we agreed on this approach, because apparently there
>> are no active users of them. See the RFC from August 2013 asking for
>> removal of the whole platform [1].
>>
>> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
>>
>>
> Great work, everything
>
> Acked-by: Arnd Bergmann<arnd@arndb.de>
>
> I hope we can get this into linux-next soon so we can do some more
> cleanups on top.
Sorry for a little bit late applying, I just wanted to get ack from
driver maintainers but... anyway I'll apply this series so you may see
this on Monday in -next :)
Tomasz, many thanks for your effort and time.
- Kukjin
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-12 22:57 ` Kukjin Kim
0 siblings, 0 replies; 19+ messages in thread
From: Kukjin Kim @ 2014-07-12 22:57 UTC (permalink / raw)
To: linux-arm-kernel
On 07/05/14 05:15, Arnd Bergmann wrote:
> On Friday 04 July 2014 19:48:00 Tomasz Figa wrote:
>> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
>> into a DT-only and multiplatform-aware platform. It consists of several
>> steps to gradually replace legacy code with one meeting current standards
>> and then finally remove unused remnants.
>>
>> Patches 1-6 migrate the platform to fully use the Common Clock Framework
>> and get rid of legacy private clock code, of which s5pv210 was the last
>> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
>> USB to be supported when using DT. Further three patches (8-10) add DT
>> support for mach-s5pv210 and necessary DT sources for currently supported
>> boards. Patch 11 removes board files and code directly related to them,
>> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
>> prepare remaining code for multiplatform enablement, which is finally done
>> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
>> unused code left after making the last S5P platform DT-only.
>>
>> Build tested patch by patch on following configs:
>> - s3c2410_defconfig (with DT support enabled),
>> - s3c6400_defconfig (with DT support enabled),
>> - s5pv210_defconfig (with DT support enabled after patches adding it),
>> - exynos_defconfig,
>> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>>
>> Boot tested on s5pv210-goni board.
>>
>> Note that support for smdkc110, smdkv210 and torbreck boards is provided
>> by moving data from existing board files to new device tree sources. No
>> testing was performed due to mentioned board not being available anymore.
>> However I believe we agreed on this approach, because apparently there
>> are no active users of them. See the RFC from August 2013 asking for
>> removal of the whole platform [1].
>>
>> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
>>
>>
> Great work, everything
>
> Acked-by: Arnd Bergmann<arnd@arndb.de>
>
> I hope we can get this into linux-next soon so we can do some more
> cleanups on top.
Sorry for a little bit late applying, I just wanted to get ack from
driver maintainers but... anyway I'll apply this series so you may see
this on Monday in -next :)
Tomasz, many thanks for your effort and time.
- Kukjin
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
2014-07-04 17:48 ` Tomasz Figa
@ 2014-07-04 20:15 ` Arnd Bergmann
-1 siblings, 0 replies; 19+ messages in thread
From: Arnd Bergmann @ 2014-07-04 20:15 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Tomasz Figa, linux-samsung-soc, Kukjin Kim, Heiko Stübner,
linux-kernel, Tomasz Figa, Mark Brown, Olof Johansson,
Marek Szyprowski
On Friday 04 July 2014 19:48:00 Tomasz Figa wrote:
> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
> into a DT-only and multiplatform-aware platform. It consists of several
> steps to gradually replace legacy code with one meeting current standards
> and then finally remove unused remnants.
>
> Patches 1-6 migrate the platform to fully use the Common Clock Framework
> and get rid of legacy private clock code, of which s5pv210 was the last
> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
> USB to be supported when using DT. Further three patches (8-10) add DT
> support for mach-s5pv210 and necessary DT sources for currently supported
> boards. Patch 11 removes board files and code directly related to them,
> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
> prepare remaining code for multiplatform enablement, which is finally done
> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
> unused code left after making the last S5P platform DT-only.
>
> Build tested patch by patch on following configs:
> - s3c2410_defconfig (with DT support enabled),
> - s3c6400_defconfig (with DT support enabled),
> - s5pv210_defconfig (with DT support enabled after patches adding it),
> - exynos_defconfig,
> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>
> Boot tested on s5pv210-goni board.
>
> Note that support for smdkc110, smdkv210 and torbreck boards is provided
> by moving data from existing board files to new device tree sources. No
> testing was performed due to mentioned board not being available anymore.
> However I believe we agreed on this approach, because apparently there
> are no active users of them. See the RFC from August 2013 asking for
> removal of the whole platform [1].
>
> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
>
>
Great work, everything
Acked-by: Arnd Bergmann <arnd@arndb.de>
I hope we can get this into linux-next soon so we can do some more
cleanups on top.
Arnd
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-04 20:15 ` Arnd Bergmann
0 siblings, 0 replies; 19+ messages in thread
From: Arnd Bergmann @ 2014-07-04 20:15 UTC (permalink / raw)
To: linux-arm-kernel
On Friday 04 July 2014 19:48:00 Tomasz Figa wrote:
> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
> into a DT-only and multiplatform-aware platform. It consists of several
> steps to gradually replace legacy code with one meeting current standards
> and then finally remove unused remnants.
>
> Patches 1-6 migrate the platform to fully use the Common Clock Framework
> and get rid of legacy private clock code, of which s5pv210 was the last
> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
> USB to be supported when using DT. Further three patches (8-10) add DT
> support for mach-s5pv210 and necessary DT sources for currently supported
> boards. Patch 11 removes board files and code directly related to them,
> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
> prepare remaining code for multiplatform enablement, which is finally done
> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
> unused code left after making the last S5P platform DT-only.
>
> Build tested patch by patch on following configs:
> - s3c2410_defconfig (with DT support enabled),
> - s3c6400_defconfig (with DT support enabled),
> - s5pv210_defconfig (with DT support enabled after patches adding it),
> - exynos_defconfig,
> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>
> Boot tested on s5pv210-goni board.
>
> Note that support for smdkc110, smdkv210 and torbreck boards is provided
> by moving data from existing board files to new device tree sources. No
> testing was performed due to mentioned board not being available anymore.
> However I believe we agreed on this approach, because apparently there
> are no active users of them. See the RFC from August 2013 asking for
> removal of the whole platform [1].
>
> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
>
>
Great work, everything
Acked-by: Arnd Bergmann <arnd@arndb.de>
I hope we can get this into linux-next soon so we can do some more
cleanups on top.
Arnd
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
2014-07-04 17:48 ` Tomasz Figa
@ 2014-07-04 17:53 ` Tomasz Figa
-1 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-04 17:53 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, linux-kernel, Kukjin Kim, Arnd Bergmann,
Olof Johansson, Marek Szyprowski, Mark Brown, Heiko Stübner,
Tomasz Figa
Aha, I forgot to add that the series is based on Kukjin's for-next
branch with "pwm: samsung: remove s5pc100 related pwm codes" patch
reverted and you can find a ready branch here:
https://github.com/tom3q/linux.git v3.17-s5pv210-dt
Sorry for the noise.
Best regards,
Tomasz
On 04.07.2014 19:48, Tomasz Figa wrote:
> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
> into a DT-only and multiplatform-aware platform. It consists of several
> steps to gradually replace legacy code with one meeting current standards
> and then finally remove unused remnants.
>
> Patches 1-6 migrate the platform to fully use the Common Clock Framework
> and get rid of legacy private clock code, of which s5pv210 was the last
> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
> USB to be supported when using DT. Further three patches (8-10) add DT
> support for mach-s5pv210 and necessary DT sources for currently supported
> boards. Patch 11 removes board files and code directly related to them,
> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
> prepare remaining code for multiplatform enablement, which is finally done
> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
> unused code left after making the last S5P platform DT-only.
>
> Build tested patch by patch on following configs:
> - s3c2410_defconfig (with DT support enabled),
> - s3c6400_defconfig (with DT support enabled),
> - s5pv210_defconfig (with DT support enabled after patches adding it),
> - exynos_defconfig,
> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>
> Boot tested on s5pv210-goni board.
>
> Note that support for smdkc110, smdkv210 and torbreck boards is provided
> by moving data from existing board files to new device tree sources. No
> testing was performed due to mentioned board not being available anymore.
> However I believe we agreed on this approach, because apparently there
> are no active users of them. See the RFC from August 2013 asking for
> removal of the whole platform [1].
>
> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
>
> Mateusz Krawczuk (6):
> clk: samsung: Add clock driver for S5PV210 and compatible SoCs
> ARM: s5pv210: Migrate clock handling to Common Clock Framework
> phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
> ARM: s5pv210: Add board file for boot using Device Tree
> ARM: Samsung: DT: Add Device tree for s5pv210
> ARM: Samsung: DT: Add Device tree for S5PC110/S5PV210 Boards
>
> Tomasz Figa (13):
> cpufreq: s3c24xx: Remove some dead code
> serial: samsung: Remove support for legacy clock code
> ARM: SAMSUNG: Remove legacy clock code
> clk: samsung: Add S5PV210 Audio Subsystem clock driver
> ARM: S5PV210: Remove support for board files
> ARM: S5PV210: Untie PM support from legacy code
> ARM: s5pv210: move debug-macro.S into the common space
> ARM: s5pv210: Register cpufreq platform device
> cpufreq: s5pv210: Make the driver multiplatform aware
> ARM: s5pv210: Enable multi-platform build support
> gpio: samsung: Remove legacy support of S5PV210
> ARM: SAMSUNG: Remove remaining legacy code
> clk: samsung: s5pv210: Remove legacy board support
>
> .../bindings/clock/clk-s5pv210-audss.txt | 53 +
> .../bindings/clock/samsung,s5pv210-clock.txt | 78 ++
> .../devicetree/bindings/phy/samsung-phy.txt | 1 +
> arch/arm/Kconfig | 22 +-
> arch/arm/Kconfig.debug | 12 +-
> arch/arm/Makefile | 4 +-
> arch/arm/boot/dts/Makefile | 5 +
> arch/arm/boot/dts/s5pv210-aquila.dts | 392 ++++++
> arch/arm/boot/dts/s5pv210-goni.dts | 449 +++++++
> arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 839 ++++++++++++
> arch/arm/boot/dts/s5pv210-smdkc110.dts | 78 ++
> arch/arm/boot/dts/s5pv210-smdkv210.dts | 238 ++++
> arch/arm/boot/dts/s5pv210-torbreck.dts | 92 ++
> arch/arm/boot/dts/s5pv210.dtsi | 633 +++++++++
> arch/arm/include/debug/s5pv210.S | 34 +
> arch/arm/mach-exynos/pm.c | 1 -
> arch/arm/mach-s3c24xx/common.c | 2 -
> arch/arm/mach-s3c24xx/iotiming-s3c2412.c | 1 -
> arch/arm/mach-s3c24xx/mach-h1940.c | 5 +-
> arch/arm/mach-s3c24xx/mach-jive.c | 1 -
> arch/arm/mach-s3c24xx/mach-smdk2413.c | 1 -
> arch/arm/mach-s3c24xx/mach-smdk2416.c | 1 -
> arch/arm/mach-s3c24xx/mach-smdk2443.c | 1 -
> arch/arm/mach-s3c24xx/mach-vstms.c | 1 -
> arch/arm/mach-s3c24xx/s3c2410.c | 6 -
> arch/arm/mach-s3c24xx/s3c2412.c | 6 -
> arch/arm/mach-s3c24xx/s3c2442.c | 1 -
> arch/arm/mach-s3c24xx/s3c244x.c | 6 -
> arch/arm/mach-s3c64xx/mach-anw6410.c | 1 -
> arch/arm/mach-s3c64xx/mach-crag6410.c | 1 -
> arch/arm/mach-s3c64xx/mach-hmt.c | 1 -
> arch/arm/mach-s3c64xx/mach-ncp.c | 1 -
> arch/arm/mach-s3c64xx/mach-smartq.c | 1 -
> arch/arm/mach-s3c64xx/mach-smdk6400.c | 1 -
> arch/arm/mach-s3c64xx/mach-smdk6410.c | 1 -
> arch/arm/mach-s3c64xx/s3c6400.c | 1 -
> arch/arm/mach-s3c64xx/s3c6410.c | 1 -
> arch/arm/mach-s5pv210/Kconfig | 197 +--
> arch/arm/mach-s5pv210/Makefile | 29 +-
> arch/arm/mach-s5pv210/Makefile.boot | 2 -
> arch/arm/mach-s5pv210/clock.c | 1365 --------------------
> arch/arm/mach-s5pv210/common.c | 279 ----
> arch/arm/mach-s5pv210/common.h | 21 +-
> arch/arm/mach-s5pv210/dev-audio.c | 246 ----
> arch/arm/mach-s5pv210/dma.c | 130 --
> arch/arm/mach-s5pv210/include/mach/debug-macro.S | 41 -
> arch/arm/mach-s5pv210/include/mach/dma.h | 26 -
> arch/arm/mach-s5pv210/include/mach/gpio.h | 140 --
> arch/arm/mach-s5pv210/include/mach/hardware.h | 18 -
> arch/arm/mach-s5pv210/include/mach/irqs.h | 137 --
> arch/arm/mach-s5pv210/include/mach/map.h | 158 ---
> arch/arm/mach-s5pv210/include/mach/memory.h | 27 -
> arch/arm/mach-s5pv210/include/mach/pm-core.h | 46 -
> arch/arm/mach-s5pv210/include/mach/regs-clock.h | 2 +-
> arch/arm/mach-s5pv210/include/mach/regs-gpio.h | 41 -
> arch/arm/mach-s5pv210/include/mach/regs-irq.h | 18 -
> arch/arm/mach-s5pv210/mach-aquila.c | 687 ----------
> arch/arm/mach-s5pv210/mach-goni.c | 916 -------------
> arch/arm/mach-s5pv210/mach-smdkc110.c | 159 ---
> arch/arm/mach-s5pv210/mach-smdkv210.c | 337 -----
> arch/arm/mach-s5pv210/mach-torbreck.c | 135 --
> arch/arm/mach-s5pv210/pm.c | 147 ++-
> arch/arm/mach-s5pv210/s5pv210.c | 77 ++
> arch/arm/mach-s5pv210/setup-fb-24bpp.c | 49 -
> arch/arm/mach-s5pv210/setup-fimc.c | 43 -
> arch/arm/mach-s5pv210/setup-i2c0.c | 28 -
> arch/arm/mach-s5pv210/setup-i2c1.c | 28 -
> arch/arm/mach-s5pv210/setup-i2c2.c | 28 -
> arch/arm/mach-s5pv210/setup-ide.c | 39 -
> arch/arm/mach-s5pv210/setup-keypad.c | 24 -
> arch/arm/mach-s5pv210/setup-sdhci-gpio.c | 103 --
> arch/arm/mach-s5pv210/setup-spi.c | 34 -
> arch/arm/mach-s5pv210/setup-usb-phy.c | 95 --
> arch/arm/mach-s5pv210/sleep.S | 36 +
> arch/arm/plat-samsung/Kconfig | 143 +-
> arch/arm/plat-samsung/Makefile | 15 -
> arch/arm/plat-samsung/clock-clksrc.c | 212 ---
> arch/arm/plat-samsung/clock.c | 539 --------
> arch/arm/plat-samsung/cpu.c | 3 +-
> arch/arm/plat-samsung/devs.c | 330 -----
> arch/arm/plat-samsung/include/plat/camport.h | 28 -
> arch/arm/plat-samsung/include/plat/clock-clksrc.h | 83 --
> arch/arm/plat-samsung/include/plat/clock.h | 152 ---
> arch/arm/plat-samsung/include/plat/cpu-freq-core.h | 3 -
> arch/arm/plat-samsung/include/plat/cpu.h | 13 -
> arch/arm/plat-samsung/include/plat/devs.h | 42 -
> arch/arm/plat-samsung/include/plat/fb-core.h | 15 -
> arch/arm/plat-samsung/include/plat/fb.h | 22 -
> arch/arm/plat-samsung/include/plat/fimc-core.h | 51 -
> arch/arm/plat-samsung/include/plat/gpio-cfg.h | 64 -
> arch/arm/plat-samsung/include/plat/hdmi.h | 16 -
> arch/arm/plat-samsung/include/plat/irqs.h | 72 --
> arch/arm/plat-samsung/include/plat/mfc.h | 35 -
> arch/arm/plat-samsung/include/plat/pll.h | 323 -----
> arch/arm/plat-samsung/include/plat/s5p-clock.h | 65 -
> arch/arm/plat-samsung/include/plat/sdhci.h | 47 -
> arch/arm/plat-samsung/include/plat/tv-core.h | 44 -
> arch/arm/plat-samsung/init.c | 1 -
> arch/arm/plat-samsung/pm-gpio.c | 4 +-
> arch/arm/plat-samsung/s5p-clock.c | 294 -----
> arch/arm/plat-samsung/s5p-dev-mfc.c | 81 +-
> arch/arm/plat-samsung/s5p-dev-uart.c | 88 --
> arch/arm/plat-samsung/s5p-irq-eint.c | 221 ----
> arch/arm/plat-samsung/s5p-irq-gpioint.c | 218 ----
> arch/arm/plat-samsung/s5p-irq-pm.c | 92 --
> arch/arm/plat-samsung/s5p-irq.c | 31 -
> arch/arm/plat-samsung/s5p-pm.c | 40 -
> arch/arm/plat-samsung/s5p-sleep.S | 45 -
> drivers/clk/samsung/Makefile | 1 +
> drivers/clk/samsung/clk-s5pv210-audss.c | 241 ++++
> drivers/clk/samsung/clk-s5pv210.c | 856 ++++++++++++
> drivers/cpufreq/s3c2410-cpufreq.c | 2 -
> drivers/cpufreq/s3c2412-cpufreq.c | 3 -
> drivers/cpufreq/s3c2440-cpufreq.c | 3 -
> drivers/cpufreq/s3c24xx-cpufreq.c | 1 -
> drivers/cpufreq/s5pv210-cpufreq.c | 131 +-
> drivers/gpio/gpio-samsung.c | 240 ----
> drivers/phy/Kconfig | 10 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-s5pv210-usb2.c | 187 +++
> drivers/phy/phy-samsung-usb2.c | 6 +
> drivers/phy/phy-samsung-usb2.h | 1 +
> drivers/tty/serial/samsung.c | 4 -
> include/dt-bindings/clock/s5pv210-audss.h | 34 +
> include/dt-bindings/clock/s5pv210.h | 239 ++++
> 125 files changed, 4843 insertions(+), 9409 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt
> create mode 100644 Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt
> create mode 100644 arch/arm/boot/dts/s5pv210-aquila.dts
> create mode 100644 arch/arm/boot/dts/s5pv210-goni.dts
> create mode 100644 arch/arm/boot/dts/s5pv210-pinctrl.dtsi
> create mode 100644 arch/arm/boot/dts/s5pv210-smdkc110.dts
> create mode 100644 arch/arm/boot/dts/s5pv210-smdkv210.dts
> create mode 100644 arch/arm/boot/dts/s5pv210-torbreck.dts
> create mode 100644 arch/arm/boot/dts/s5pv210.dtsi
> create mode 100644 arch/arm/include/debug/s5pv210.S
> delete mode 100644 arch/arm/mach-s5pv210/Makefile.boot
> delete mode 100644 arch/arm/mach-s5pv210/clock.c
> delete mode 100644 arch/arm/mach-s5pv210/common.c
> delete mode 100644 arch/arm/mach-s5pv210/dev-audio.c
> delete mode 100644 arch/arm/mach-s5pv210/dma.c
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/debug-macro.S
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/dma.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/gpio.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/hardware.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/irqs.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/map.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/memory.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/pm-core.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-gpio.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-irq.h
> delete mode 100644 arch/arm/mach-s5pv210/mach-aquila.c
> delete mode 100644 arch/arm/mach-s5pv210/mach-goni.c
> delete mode 100644 arch/arm/mach-s5pv210/mach-smdkc110.c
> delete mode 100644 arch/arm/mach-s5pv210/mach-smdkv210.c
> delete mode 100644 arch/arm/mach-s5pv210/mach-torbreck.c
> create mode 100644 arch/arm/mach-s5pv210/s5pv210.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-fb-24bpp.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-fimc.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-i2c0.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-i2c1.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-i2c2.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-ide.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-keypad.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-sdhci-gpio.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-spi.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-usb-phy.c
> create mode 100644 arch/arm/mach-s5pv210/sleep.S
> delete mode 100644 arch/arm/plat-samsung/clock-clksrc.c
> delete mode 100644 arch/arm/plat-samsung/clock.c
> delete mode 100644 arch/arm/plat-samsung/include/plat/camport.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/clock-clksrc.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/clock.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/fimc-core.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/hdmi.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/irqs.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/mfc.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/pll.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/s5p-clock.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/tv-core.h
> delete mode 100644 arch/arm/plat-samsung/s5p-clock.c
> delete mode 100644 arch/arm/plat-samsung/s5p-dev-uart.c
> delete mode 100644 arch/arm/plat-samsung/s5p-irq-eint.c
> delete mode 100644 arch/arm/plat-samsung/s5p-irq-gpioint.c
> delete mode 100644 arch/arm/plat-samsung/s5p-irq-pm.c
> delete mode 100644 arch/arm/plat-samsung/s5p-irq.c
> delete mode 100644 arch/arm/plat-samsung/s5p-pm.c
> delete mode 100644 arch/arm/plat-samsung/s5p-sleep.S
> create mode 100644 drivers/clk/samsung/clk-s5pv210-audss.c
> create mode 100644 drivers/clk/samsung/clk-s5pv210.c
> create mode 100644 drivers/phy/phy-s5pv210-usb2.c
> create mode 100644 include/dt-bindings/clock/s5pv210-audss.h
> create mode 100644 include/dt-bindings/clock/s5pv210.h
>
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-04 17:53 ` Tomasz Figa
0 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-04 17:53 UTC (permalink / raw)
To: linux-arm-kernel
Aha, I forgot to add that the series is based on Kukjin's for-next
branch with "pwm: samsung: remove s5pc100 related pwm codes" patch
reverted and you can find a ready branch here:
https://github.com/tom3q/linux.git v3.17-s5pv210-dt
Sorry for the noise.
Best regards,
Tomasz
On 04.07.2014 19:48, Tomasz Figa wrote:
> This huge series is a (hopefully final) attempt to convert Samsung S5PV210
> into a DT-only and multiplatform-aware platform. It consists of several
> steps to gradually replace legacy code with one meeting current standards
> and then finally remove unused remnants.
>
> Patches 1-6 migrate the platform to fully use the Common Clock Framework
> and get rid of legacy private clock code, of which s5pv210 was the last
> user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
> USB to be supported when using DT. Further three patches (8-10) add DT
> support for mach-s5pv210 and necessary DT sources for currently supported
> boards. Patch 11 removes board files and code directly related to them,
> effectively making s5pv210 a DT-only platform. In next step, patches 12-15
> prepare remaining code for multiplatform enablement, which is finally done
> in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
> unused code left after making the last S5P platform DT-only.
>
> Build tested patch by patch on following configs:
> - s3c2410_defconfig (with DT support enabled),
> - s3c6400_defconfig (with DT support enabled),
> - s5pv210_defconfig (with DT support enabled after patches adding it),
> - exynos_defconfig,
> - exynos_defconfig with S5PV210 enabled in multiplatform configuration.
>
> Boot tested on s5pv210-goni board.
>
> Note that support for smdkc110, smdkv210 and torbreck boards is provided
> by moving data from existing board files to new device tree sources. No
> testing was performed due to mentioned board not being available anymore.
> However I believe we agreed on this approach, because apparently there
> are no active users of them. See the RFC from August 2013 asking for
> removal of the whole platform [1].
>
> [1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
>
> Mateusz Krawczuk (6):
> clk: samsung: Add clock driver for S5PV210 and compatible SoCs
> ARM: s5pv210: Migrate clock handling to Common Clock Framework
> phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
> ARM: s5pv210: Add board file for boot using Device Tree
> ARM: Samsung: DT: Add Device tree for s5pv210
> ARM: Samsung: DT: Add Device tree for S5PC110/S5PV210 Boards
>
> Tomasz Figa (13):
> cpufreq: s3c24xx: Remove some dead code
> serial: samsung: Remove support for legacy clock code
> ARM: SAMSUNG: Remove legacy clock code
> clk: samsung: Add S5PV210 Audio Subsystem clock driver
> ARM: S5PV210: Remove support for board files
> ARM: S5PV210: Untie PM support from legacy code
> ARM: s5pv210: move debug-macro.S into the common space
> ARM: s5pv210: Register cpufreq platform device
> cpufreq: s5pv210: Make the driver multiplatform aware
> ARM: s5pv210: Enable multi-platform build support
> gpio: samsung: Remove legacy support of S5PV210
> ARM: SAMSUNG: Remove remaining legacy code
> clk: samsung: s5pv210: Remove legacy board support
>
> .../bindings/clock/clk-s5pv210-audss.txt | 53 +
> .../bindings/clock/samsung,s5pv210-clock.txt | 78 ++
> .../devicetree/bindings/phy/samsung-phy.txt | 1 +
> arch/arm/Kconfig | 22 +-
> arch/arm/Kconfig.debug | 12 +-
> arch/arm/Makefile | 4 +-
> arch/arm/boot/dts/Makefile | 5 +
> arch/arm/boot/dts/s5pv210-aquila.dts | 392 ++++++
> arch/arm/boot/dts/s5pv210-goni.dts | 449 +++++++
> arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 839 ++++++++++++
> arch/arm/boot/dts/s5pv210-smdkc110.dts | 78 ++
> arch/arm/boot/dts/s5pv210-smdkv210.dts | 238 ++++
> arch/arm/boot/dts/s5pv210-torbreck.dts | 92 ++
> arch/arm/boot/dts/s5pv210.dtsi | 633 +++++++++
> arch/arm/include/debug/s5pv210.S | 34 +
> arch/arm/mach-exynos/pm.c | 1 -
> arch/arm/mach-s3c24xx/common.c | 2 -
> arch/arm/mach-s3c24xx/iotiming-s3c2412.c | 1 -
> arch/arm/mach-s3c24xx/mach-h1940.c | 5 +-
> arch/arm/mach-s3c24xx/mach-jive.c | 1 -
> arch/arm/mach-s3c24xx/mach-smdk2413.c | 1 -
> arch/arm/mach-s3c24xx/mach-smdk2416.c | 1 -
> arch/arm/mach-s3c24xx/mach-smdk2443.c | 1 -
> arch/arm/mach-s3c24xx/mach-vstms.c | 1 -
> arch/arm/mach-s3c24xx/s3c2410.c | 6 -
> arch/arm/mach-s3c24xx/s3c2412.c | 6 -
> arch/arm/mach-s3c24xx/s3c2442.c | 1 -
> arch/arm/mach-s3c24xx/s3c244x.c | 6 -
> arch/arm/mach-s3c64xx/mach-anw6410.c | 1 -
> arch/arm/mach-s3c64xx/mach-crag6410.c | 1 -
> arch/arm/mach-s3c64xx/mach-hmt.c | 1 -
> arch/arm/mach-s3c64xx/mach-ncp.c | 1 -
> arch/arm/mach-s3c64xx/mach-smartq.c | 1 -
> arch/arm/mach-s3c64xx/mach-smdk6400.c | 1 -
> arch/arm/mach-s3c64xx/mach-smdk6410.c | 1 -
> arch/arm/mach-s3c64xx/s3c6400.c | 1 -
> arch/arm/mach-s3c64xx/s3c6410.c | 1 -
> arch/arm/mach-s5pv210/Kconfig | 197 +--
> arch/arm/mach-s5pv210/Makefile | 29 +-
> arch/arm/mach-s5pv210/Makefile.boot | 2 -
> arch/arm/mach-s5pv210/clock.c | 1365 --------------------
> arch/arm/mach-s5pv210/common.c | 279 ----
> arch/arm/mach-s5pv210/common.h | 21 +-
> arch/arm/mach-s5pv210/dev-audio.c | 246 ----
> arch/arm/mach-s5pv210/dma.c | 130 --
> arch/arm/mach-s5pv210/include/mach/debug-macro.S | 41 -
> arch/arm/mach-s5pv210/include/mach/dma.h | 26 -
> arch/arm/mach-s5pv210/include/mach/gpio.h | 140 --
> arch/arm/mach-s5pv210/include/mach/hardware.h | 18 -
> arch/arm/mach-s5pv210/include/mach/irqs.h | 137 --
> arch/arm/mach-s5pv210/include/mach/map.h | 158 ---
> arch/arm/mach-s5pv210/include/mach/memory.h | 27 -
> arch/arm/mach-s5pv210/include/mach/pm-core.h | 46 -
> arch/arm/mach-s5pv210/include/mach/regs-clock.h | 2 +-
> arch/arm/mach-s5pv210/include/mach/regs-gpio.h | 41 -
> arch/arm/mach-s5pv210/include/mach/regs-irq.h | 18 -
> arch/arm/mach-s5pv210/mach-aquila.c | 687 ----------
> arch/arm/mach-s5pv210/mach-goni.c | 916 -------------
> arch/arm/mach-s5pv210/mach-smdkc110.c | 159 ---
> arch/arm/mach-s5pv210/mach-smdkv210.c | 337 -----
> arch/arm/mach-s5pv210/mach-torbreck.c | 135 --
> arch/arm/mach-s5pv210/pm.c | 147 ++-
> arch/arm/mach-s5pv210/s5pv210.c | 77 ++
> arch/arm/mach-s5pv210/setup-fb-24bpp.c | 49 -
> arch/arm/mach-s5pv210/setup-fimc.c | 43 -
> arch/arm/mach-s5pv210/setup-i2c0.c | 28 -
> arch/arm/mach-s5pv210/setup-i2c1.c | 28 -
> arch/arm/mach-s5pv210/setup-i2c2.c | 28 -
> arch/arm/mach-s5pv210/setup-ide.c | 39 -
> arch/arm/mach-s5pv210/setup-keypad.c | 24 -
> arch/arm/mach-s5pv210/setup-sdhci-gpio.c | 103 --
> arch/arm/mach-s5pv210/setup-spi.c | 34 -
> arch/arm/mach-s5pv210/setup-usb-phy.c | 95 --
> arch/arm/mach-s5pv210/sleep.S | 36 +
> arch/arm/plat-samsung/Kconfig | 143 +-
> arch/arm/plat-samsung/Makefile | 15 -
> arch/arm/plat-samsung/clock-clksrc.c | 212 ---
> arch/arm/plat-samsung/clock.c | 539 --------
> arch/arm/plat-samsung/cpu.c | 3 +-
> arch/arm/plat-samsung/devs.c | 330 -----
> arch/arm/plat-samsung/include/plat/camport.h | 28 -
> arch/arm/plat-samsung/include/plat/clock-clksrc.h | 83 --
> arch/arm/plat-samsung/include/plat/clock.h | 152 ---
> arch/arm/plat-samsung/include/plat/cpu-freq-core.h | 3 -
> arch/arm/plat-samsung/include/plat/cpu.h | 13 -
> arch/arm/plat-samsung/include/plat/devs.h | 42 -
> arch/arm/plat-samsung/include/plat/fb-core.h | 15 -
> arch/arm/plat-samsung/include/plat/fb.h | 22 -
> arch/arm/plat-samsung/include/plat/fimc-core.h | 51 -
> arch/arm/plat-samsung/include/plat/gpio-cfg.h | 64 -
> arch/arm/plat-samsung/include/plat/hdmi.h | 16 -
> arch/arm/plat-samsung/include/plat/irqs.h | 72 --
> arch/arm/plat-samsung/include/plat/mfc.h | 35 -
> arch/arm/plat-samsung/include/plat/pll.h | 323 -----
> arch/arm/plat-samsung/include/plat/s5p-clock.h | 65 -
> arch/arm/plat-samsung/include/plat/sdhci.h | 47 -
> arch/arm/plat-samsung/include/plat/tv-core.h | 44 -
> arch/arm/plat-samsung/init.c | 1 -
> arch/arm/plat-samsung/pm-gpio.c | 4 +-
> arch/arm/plat-samsung/s5p-clock.c | 294 -----
> arch/arm/plat-samsung/s5p-dev-mfc.c | 81 +-
> arch/arm/plat-samsung/s5p-dev-uart.c | 88 --
> arch/arm/plat-samsung/s5p-irq-eint.c | 221 ----
> arch/arm/plat-samsung/s5p-irq-gpioint.c | 218 ----
> arch/arm/plat-samsung/s5p-irq-pm.c | 92 --
> arch/arm/plat-samsung/s5p-irq.c | 31 -
> arch/arm/plat-samsung/s5p-pm.c | 40 -
> arch/arm/plat-samsung/s5p-sleep.S | 45 -
> drivers/clk/samsung/Makefile | 1 +
> drivers/clk/samsung/clk-s5pv210-audss.c | 241 ++++
> drivers/clk/samsung/clk-s5pv210.c | 856 ++++++++++++
> drivers/cpufreq/s3c2410-cpufreq.c | 2 -
> drivers/cpufreq/s3c2412-cpufreq.c | 3 -
> drivers/cpufreq/s3c2440-cpufreq.c | 3 -
> drivers/cpufreq/s3c24xx-cpufreq.c | 1 -
> drivers/cpufreq/s5pv210-cpufreq.c | 131 +-
> drivers/gpio/gpio-samsung.c | 240 ----
> drivers/phy/Kconfig | 10 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-s5pv210-usb2.c | 187 +++
> drivers/phy/phy-samsung-usb2.c | 6 +
> drivers/phy/phy-samsung-usb2.h | 1 +
> drivers/tty/serial/samsung.c | 4 -
> include/dt-bindings/clock/s5pv210-audss.h | 34 +
> include/dt-bindings/clock/s5pv210.h | 239 ++++
> 125 files changed, 4843 insertions(+), 9409 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt
> create mode 100644 Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt
> create mode 100644 arch/arm/boot/dts/s5pv210-aquila.dts
> create mode 100644 arch/arm/boot/dts/s5pv210-goni.dts
> create mode 100644 arch/arm/boot/dts/s5pv210-pinctrl.dtsi
> create mode 100644 arch/arm/boot/dts/s5pv210-smdkc110.dts
> create mode 100644 arch/arm/boot/dts/s5pv210-smdkv210.dts
> create mode 100644 arch/arm/boot/dts/s5pv210-torbreck.dts
> create mode 100644 arch/arm/boot/dts/s5pv210.dtsi
> create mode 100644 arch/arm/include/debug/s5pv210.S
> delete mode 100644 arch/arm/mach-s5pv210/Makefile.boot
> delete mode 100644 arch/arm/mach-s5pv210/clock.c
> delete mode 100644 arch/arm/mach-s5pv210/common.c
> delete mode 100644 arch/arm/mach-s5pv210/dev-audio.c
> delete mode 100644 arch/arm/mach-s5pv210/dma.c
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/debug-macro.S
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/dma.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/gpio.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/hardware.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/irqs.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/map.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/memory.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/pm-core.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-gpio.h
> delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-irq.h
> delete mode 100644 arch/arm/mach-s5pv210/mach-aquila.c
> delete mode 100644 arch/arm/mach-s5pv210/mach-goni.c
> delete mode 100644 arch/arm/mach-s5pv210/mach-smdkc110.c
> delete mode 100644 arch/arm/mach-s5pv210/mach-smdkv210.c
> delete mode 100644 arch/arm/mach-s5pv210/mach-torbreck.c
> create mode 100644 arch/arm/mach-s5pv210/s5pv210.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-fb-24bpp.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-fimc.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-i2c0.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-i2c1.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-i2c2.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-ide.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-keypad.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-sdhci-gpio.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-spi.c
> delete mode 100644 arch/arm/mach-s5pv210/setup-usb-phy.c
> create mode 100644 arch/arm/mach-s5pv210/sleep.S
> delete mode 100644 arch/arm/plat-samsung/clock-clksrc.c
> delete mode 100644 arch/arm/plat-samsung/clock.c
> delete mode 100644 arch/arm/plat-samsung/include/plat/camport.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/clock-clksrc.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/clock.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/fimc-core.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/hdmi.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/irqs.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/mfc.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/pll.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/s5p-clock.h
> delete mode 100644 arch/arm/plat-samsung/include/plat/tv-core.h
> delete mode 100644 arch/arm/plat-samsung/s5p-clock.c
> delete mode 100644 arch/arm/plat-samsung/s5p-dev-uart.c
> delete mode 100644 arch/arm/plat-samsung/s5p-irq-eint.c
> delete mode 100644 arch/arm/plat-samsung/s5p-irq-gpioint.c
> delete mode 100644 arch/arm/plat-samsung/s5p-irq-pm.c
> delete mode 100644 arch/arm/plat-samsung/s5p-irq.c
> delete mode 100644 arch/arm/plat-samsung/s5p-pm.c
> delete mode 100644 arch/arm/plat-samsung/s5p-sleep.S
> create mode 100644 drivers/clk/samsung/clk-s5pv210-audss.c
> create mode 100644 drivers/clk/samsung/clk-s5pv210.c
> create mode 100644 drivers/phy/phy-s5pv210-usb2.c
> create mode 100644 include/dt-bindings/clock/s5pv210-audss.h
> create mode 100644 include/dt-bindings/clock/s5pv210.h
>
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-04 17:48 ` Tomasz Figa
0 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-04 17:48 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, linux-kernel, Kukjin Kim, Arnd Bergmann,
Olof Johansson, Marek Szyprowski, Mark Brown, Heiko Stübner,
Tomasz Figa
This huge series is a (hopefully final) attempt to convert Samsung S5PV210
into a DT-only and multiplatform-aware platform. It consists of several
steps to gradually replace legacy code with one meeting current standards
and then finally remove unused remnants.
Patches 1-6 migrate the platform to fully use the Common Clock Framework
and get rid of legacy private clock code, of which s5pv210 was the last
user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
USB to be supported when using DT. Further three patches (8-10) add DT
support for mach-s5pv210 and necessary DT sources for currently supported
boards. Patch 11 removes board files and code directly related to them,
effectively making s5pv210 a DT-only platform. In next step, patches 12-15
prepare remaining code for multiplatform enablement, which is finally done
in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
unused code left after making the last S5P platform DT-only.
Build tested patch by patch on following configs:
- s3c2410_defconfig (with DT support enabled),
- s3c6400_defconfig (with DT support enabled),
- s5pv210_defconfig (with DT support enabled after patches adding it),
- exynos_defconfig,
- exynos_defconfig with S5PV210 enabled in multiplatform configuration.
Boot tested on s5pv210-goni board.
Note that support for smdkc110, smdkv210 and torbreck boards is provided
by moving data from existing board files to new device tree sources. No
testing was performed due to mentioned board not being available anymore.
However I believe we agreed on this approach, because apparently there
are no active users of them. See the RFC from August 2013 asking for
removal of the whole platform [1].
[1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
Mateusz Krawczuk (6):
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
ARM: s5pv210: Migrate clock handling to Common Clock Framework
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
ARM: s5pv210: Add board file for boot using Device Tree
ARM: Samsung: DT: Add Device tree for s5pv210
ARM: Samsung: DT: Add Device tree for S5PC110/S5PV210 Boards
Tomasz Figa (13):
cpufreq: s3c24xx: Remove some dead code
serial: samsung: Remove support for legacy clock code
ARM: SAMSUNG: Remove legacy clock code
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: S5PV210: Remove support for board files
ARM: S5PV210: Untie PM support from legacy code
ARM: s5pv210: move debug-macro.S into the common space
ARM: s5pv210: Register cpufreq platform device
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: s5pv210: Enable multi-platform build support
gpio: samsung: Remove legacy support of S5PV210
ARM: SAMSUNG: Remove remaining legacy code
clk: samsung: s5pv210: Remove legacy board support
.../bindings/clock/clk-s5pv210-audss.txt | 53 +
.../bindings/clock/samsung,s5pv210-clock.txt | 78 ++
.../devicetree/bindings/phy/samsung-phy.txt | 1 +
arch/arm/Kconfig | 22 +-
arch/arm/Kconfig.debug | 12 +-
arch/arm/Makefile | 4 +-
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/s5pv210-aquila.dts | 392 ++++++
arch/arm/boot/dts/s5pv210-goni.dts | 449 +++++++
arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 839 ++++++++++++
arch/arm/boot/dts/s5pv210-smdkc110.dts | 78 ++
arch/arm/boot/dts/s5pv210-smdkv210.dts | 238 ++++
arch/arm/boot/dts/s5pv210-torbreck.dts | 92 ++
arch/arm/boot/dts/s5pv210.dtsi | 633 +++++++++
arch/arm/include/debug/s5pv210.S | 34 +
arch/arm/mach-exynos/pm.c | 1 -
arch/arm/mach-s3c24xx/common.c | 2 -
arch/arm/mach-s3c24xx/iotiming-s3c2412.c | 1 -
arch/arm/mach-s3c24xx/mach-h1940.c | 5 +-
arch/arm/mach-s3c24xx/mach-jive.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2413.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2416.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2443.c | 1 -
arch/arm/mach-s3c24xx/mach-vstms.c | 1 -
arch/arm/mach-s3c24xx/s3c2410.c | 6 -
arch/arm/mach-s3c24xx/s3c2412.c | 6 -
arch/arm/mach-s3c24xx/s3c2442.c | 1 -
arch/arm/mach-s3c24xx/s3c244x.c | 6 -
arch/arm/mach-s3c64xx/mach-anw6410.c | 1 -
arch/arm/mach-s3c64xx/mach-crag6410.c | 1 -
arch/arm/mach-s3c64xx/mach-hmt.c | 1 -
arch/arm/mach-s3c64xx/mach-ncp.c | 1 -
arch/arm/mach-s3c64xx/mach-smartq.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6400.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6410.c | 1 -
arch/arm/mach-s3c64xx/s3c6400.c | 1 -
arch/arm/mach-s3c64xx/s3c6410.c | 1 -
arch/arm/mach-s5pv210/Kconfig | 197 +--
arch/arm/mach-s5pv210/Makefile | 29 +-
arch/arm/mach-s5pv210/Makefile.boot | 2 -
arch/arm/mach-s5pv210/clock.c | 1365 --------------------
arch/arm/mach-s5pv210/common.c | 279 ----
arch/arm/mach-s5pv210/common.h | 21 +-
arch/arm/mach-s5pv210/dev-audio.c | 246 ----
arch/arm/mach-s5pv210/dma.c | 130 --
arch/arm/mach-s5pv210/include/mach/debug-macro.S | 41 -
arch/arm/mach-s5pv210/include/mach/dma.h | 26 -
arch/arm/mach-s5pv210/include/mach/gpio.h | 140 --
arch/arm/mach-s5pv210/include/mach/hardware.h | 18 -
arch/arm/mach-s5pv210/include/mach/irqs.h | 137 --
arch/arm/mach-s5pv210/include/mach/map.h | 158 ---
arch/arm/mach-s5pv210/include/mach/memory.h | 27 -
arch/arm/mach-s5pv210/include/mach/pm-core.h | 46 -
arch/arm/mach-s5pv210/include/mach/regs-clock.h | 2 +-
arch/arm/mach-s5pv210/include/mach/regs-gpio.h | 41 -
arch/arm/mach-s5pv210/include/mach/regs-irq.h | 18 -
arch/arm/mach-s5pv210/mach-aquila.c | 687 ----------
arch/arm/mach-s5pv210/mach-goni.c | 916 -------------
arch/arm/mach-s5pv210/mach-smdkc110.c | 159 ---
arch/arm/mach-s5pv210/mach-smdkv210.c | 337 -----
arch/arm/mach-s5pv210/mach-torbreck.c | 135 --
arch/arm/mach-s5pv210/pm.c | 147 ++-
arch/arm/mach-s5pv210/s5pv210.c | 77 ++
arch/arm/mach-s5pv210/setup-fb-24bpp.c | 49 -
arch/arm/mach-s5pv210/setup-fimc.c | 43 -
arch/arm/mach-s5pv210/setup-i2c0.c | 28 -
arch/arm/mach-s5pv210/setup-i2c1.c | 28 -
arch/arm/mach-s5pv210/setup-i2c2.c | 28 -
arch/arm/mach-s5pv210/setup-ide.c | 39 -
arch/arm/mach-s5pv210/setup-keypad.c | 24 -
arch/arm/mach-s5pv210/setup-sdhci-gpio.c | 103 --
arch/arm/mach-s5pv210/setup-spi.c | 34 -
arch/arm/mach-s5pv210/setup-usb-phy.c | 95 --
arch/arm/mach-s5pv210/sleep.S | 36 +
arch/arm/plat-samsung/Kconfig | 143 +-
arch/arm/plat-samsung/Makefile | 15 -
arch/arm/plat-samsung/clock-clksrc.c | 212 ---
arch/arm/plat-samsung/clock.c | 539 --------
arch/arm/plat-samsung/cpu.c | 3 +-
arch/arm/plat-samsung/devs.c | 330 -----
arch/arm/plat-samsung/include/plat/camport.h | 28 -
arch/arm/plat-samsung/include/plat/clock-clksrc.h | 83 --
arch/arm/plat-samsung/include/plat/clock.h | 152 ---
arch/arm/plat-samsung/include/plat/cpu-freq-core.h | 3 -
arch/arm/plat-samsung/include/plat/cpu.h | 13 -
arch/arm/plat-samsung/include/plat/devs.h | 42 -
arch/arm/plat-samsung/include/plat/fb-core.h | 15 -
arch/arm/plat-samsung/include/plat/fb.h | 22 -
arch/arm/plat-samsung/include/plat/fimc-core.h | 51 -
arch/arm/plat-samsung/include/plat/gpio-cfg.h | 64 -
arch/arm/plat-samsung/include/plat/hdmi.h | 16 -
arch/arm/plat-samsung/include/plat/irqs.h | 72 --
arch/arm/plat-samsung/include/plat/mfc.h | 35 -
arch/arm/plat-samsung/include/plat/pll.h | 323 -----
arch/arm/plat-samsung/include/plat/s5p-clock.h | 65 -
arch/arm/plat-samsung/include/plat/sdhci.h | 47 -
arch/arm/plat-samsung/include/plat/tv-core.h | 44 -
arch/arm/plat-samsung/init.c | 1 -
arch/arm/plat-samsung/pm-gpio.c | 4 +-
arch/arm/plat-samsung/s5p-clock.c | 294 -----
arch/arm/plat-samsung/s5p-dev-mfc.c | 81 +-
arch/arm/plat-samsung/s5p-dev-uart.c | 88 --
arch/arm/plat-samsung/s5p-irq-eint.c | 221 ----
arch/arm/plat-samsung/s5p-irq-gpioint.c | 218 ----
arch/arm/plat-samsung/s5p-irq-pm.c | 92 --
arch/arm/plat-samsung/s5p-irq.c | 31 -
arch/arm/plat-samsung/s5p-pm.c | 40 -
arch/arm/plat-samsung/s5p-sleep.S | 45 -
drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-s5pv210-audss.c | 241 ++++
drivers/clk/samsung/clk-s5pv210.c | 856 ++++++++++++
drivers/cpufreq/s3c2410-cpufreq.c | 2 -
drivers/cpufreq/s3c2412-cpufreq.c | 3 -
drivers/cpufreq/s3c2440-cpufreq.c | 3 -
drivers/cpufreq/s3c24xx-cpufreq.c | 1 -
drivers/cpufreq/s5pv210-cpufreq.c | 131 +-
drivers/gpio/gpio-samsung.c | 240 ----
drivers/phy/Kconfig | 10 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-s5pv210-usb2.c | 187 +++
drivers/phy/phy-samsung-usb2.c | 6 +
drivers/phy/phy-samsung-usb2.h | 1 +
drivers/tty/serial/samsung.c | 4 -
include/dt-bindings/clock/s5pv210-audss.h | 34 +
include/dt-bindings/clock/s5pv210.h | 239 ++++
125 files changed, 4843 insertions(+), 9409 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt
create mode 100644 Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt
create mode 100644 arch/arm/boot/dts/s5pv210-aquila.dts
create mode 100644 arch/arm/boot/dts/s5pv210-goni.dts
create mode 100644 arch/arm/boot/dts/s5pv210-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/s5pv210-smdkc110.dts
create mode 100644 arch/arm/boot/dts/s5pv210-smdkv210.dts
create mode 100644 arch/arm/boot/dts/s5pv210-torbreck.dts
create mode 100644 arch/arm/boot/dts/s5pv210.dtsi
create mode 100644 arch/arm/include/debug/s5pv210.S
delete mode 100644 arch/arm/mach-s5pv210/Makefile.boot
delete mode 100644 arch/arm/mach-s5pv210/clock.c
delete mode 100644 arch/arm/mach-s5pv210/common.c
delete mode 100644 arch/arm/mach-s5pv210/dev-audio.c
delete mode 100644 arch/arm/mach-s5pv210/dma.c
delete mode 100644 arch/arm/mach-s5pv210/include/mach/debug-macro.S
delete mode 100644 arch/arm/mach-s5pv210/include/mach/dma.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/hardware.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/irqs.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/map.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/memory.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/pm-core.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-irq.h
delete mode 100644 arch/arm/mach-s5pv210/mach-aquila.c
delete mode 100644 arch/arm/mach-s5pv210/mach-goni.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkc110.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkv210.c
delete mode 100644 arch/arm/mach-s5pv210/mach-torbreck.c
create mode 100644 arch/arm/mach-s5pv210/s5pv210.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fb-24bpp.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fimc.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c0.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c1.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c2.c
delete mode 100644 arch/arm/mach-s5pv210/setup-ide.c
delete mode 100644 arch/arm/mach-s5pv210/setup-keypad.c
delete mode 100644 arch/arm/mach-s5pv210/setup-sdhci-gpio.c
delete mode 100644 arch/arm/mach-s5pv210/setup-spi.c
delete mode 100644 arch/arm/mach-s5pv210/setup-usb-phy.c
create mode 100644 arch/arm/mach-s5pv210/sleep.S
delete mode 100644 arch/arm/plat-samsung/clock-clksrc.c
delete mode 100644 arch/arm/plat-samsung/clock.c
delete mode 100644 arch/arm/plat-samsung/include/plat/camport.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock-clksrc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/fimc-core.h
delete mode 100644 arch/arm/plat-samsung/include/plat/hdmi.h
delete mode 100644 arch/arm/plat-samsung/include/plat/irqs.h
delete mode 100644 arch/arm/plat-samsung/include/plat/mfc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/pll.h
delete mode 100644 arch/arm/plat-samsung/include/plat/s5p-clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/tv-core.h
delete mode 100644 arch/arm/plat-samsung/s5p-clock.c
delete mode 100644 arch/arm/plat-samsung/s5p-dev-uart.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-eint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-gpioint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq.c
delete mode 100644 arch/arm/plat-samsung/s5p-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-sleep.S
create mode 100644 drivers/clk/samsung/clk-s5pv210-audss.c
create mode 100644 drivers/clk/samsung/clk-s5pv210.c
create mode 100644 drivers/phy/phy-s5pv210-usb2.c
create mode 100644 include/dt-bindings/clock/s5pv210-audss.h
create mode 100644 include/dt-bindings/clock/s5pv210.h
--
1.9.3
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-04 17:48 ` Tomasz Figa
0 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-04 17:48 UTC (permalink / raw)
To: linux-arm-kernel
This huge series is a (hopefully final) attempt to convert Samsung S5PV210
into a DT-only and multiplatform-aware platform. It consists of several
steps to gradually replace legacy code with one meeting current standards
and then finally remove unused remnants.
Patches 1-6 migrate the platform to fully use the Common Clock Framework
and get rid of legacy private clock code, of which s5pv210 was the last
user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
USB to be supported when using DT. Further three patches (8-10) add DT
support for mach-s5pv210 and necessary DT sources for currently supported
boards. Patch 11 removes board files and code directly related to them,
effectively making s5pv210 a DT-only platform. In next step, patches 12-15
prepare remaining code for multiplatform enablement, which is finally done
in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
unused code left after making the last S5P platform DT-only.
Build tested patch by patch on following configs:
- s3c2410_defconfig (with DT support enabled),
- s3c6400_defconfig (with DT support enabled),
- s5pv210_defconfig (with DT support enabled after patches adding it),
- exynos_defconfig,
- exynos_defconfig with S5PV210 enabled in multiplatform configuration.
Boot tested on s5pv210-goni board.
Note that support for smdkc110, smdkv210 and torbreck boards is provided
by moving data from existing board files to new device tree sources. No
testing was performed due to mentioned board not being available anymore.
However I believe we agreed on this approach, because apparently there
are no active users of them. See the RFC from August 2013 asking for
removal of the whole platform [1].
[1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
Mateusz Krawczuk (6):
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
ARM: s5pv210: Migrate clock handling to Common Clock Framework
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
ARM: s5pv210: Add board file for boot using Device Tree
ARM: Samsung: DT: Add Device tree for s5pv210
ARM: Samsung: DT: Add Device tree for S5PC110/S5PV210 Boards
Tomasz Figa (13):
cpufreq: s3c24xx: Remove some dead code
serial: samsung: Remove support for legacy clock code
ARM: SAMSUNG: Remove legacy clock code
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: S5PV210: Remove support for board files
ARM: S5PV210: Untie PM support from legacy code
ARM: s5pv210: move debug-macro.S into the common space
ARM: s5pv210: Register cpufreq platform device
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: s5pv210: Enable multi-platform build support
gpio: samsung: Remove legacy support of S5PV210
ARM: SAMSUNG: Remove remaining legacy code
clk: samsung: s5pv210: Remove legacy board support
.../bindings/clock/clk-s5pv210-audss.txt | 53 +
.../bindings/clock/samsung,s5pv210-clock.txt | 78 ++
.../devicetree/bindings/phy/samsung-phy.txt | 1 +
arch/arm/Kconfig | 22 +-
arch/arm/Kconfig.debug | 12 +-
arch/arm/Makefile | 4 +-
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/s5pv210-aquila.dts | 392 ++++++
arch/arm/boot/dts/s5pv210-goni.dts | 449 +++++++
arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 839 ++++++++++++
arch/arm/boot/dts/s5pv210-smdkc110.dts | 78 ++
arch/arm/boot/dts/s5pv210-smdkv210.dts | 238 ++++
arch/arm/boot/dts/s5pv210-torbreck.dts | 92 ++
arch/arm/boot/dts/s5pv210.dtsi | 633 +++++++++
arch/arm/include/debug/s5pv210.S | 34 +
arch/arm/mach-exynos/pm.c | 1 -
arch/arm/mach-s3c24xx/common.c | 2 -
arch/arm/mach-s3c24xx/iotiming-s3c2412.c | 1 -
arch/arm/mach-s3c24xx/mach-h1940.c | 5 +-
arch/arm/mach-s3c24xx/mach-jive.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2413.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2416.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2443.c | 1 -
arch/arm/mach-s3c24xx/mach-vstms.c | 1 -
arch/arm/mach-s3c24xx/s3c2410.c | 6 -
arch/arm/mach-s3c24xx/s3c2412.c | 6 -
arch/arm/mach-s3c24xx/s3c2442.c | 1 -
arch/arm/mach-s3c24xx/s3c244x.c | 6 -
arch/arm/mach-s3c64xx/mach-anw6410.c | 1 -
arch/arm/mach-s3c64xx/mach-crag6410.c | 1 -
arch/arm/mach-s3c64xx/mach-hmt.c | 1 -
arch/arm/mach-s3c64xx/mach-ncp.c | 1 -
arch/arm/mach-s3c64xx/mach-smartq.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6400.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6410.c | 1 -
arch/arm/mach-s3c64xx/s3c6400.c | 1 -
arch/arm/mach-s3c64xx/s3c6410.c | 1 -
arch/arm/mach-s5pv210/Kconfig | 197 +--
arch/arm/mach-s5pv210/Makefile | 29 +-
arch/arm/mach-s5pv210/Makefile.boot | 2 -
arch/arm/mach-s5pv210/clock.c | 1365 --------------------
arch/arm/mach-s5pv210/common.c | 279 ----
arch/arm/mach-s5pv210/common.h | 21 +-
arch/arm/mach-s5pv210/dev-audio.c | 246 ----
arch/arm/mach-s5pv210/dma.c | 130 --
arch/arm/mach-s5pv210/include/mach/debug-macro.S | 41 -
arch/arm/mach-s5pv210/include/mach/dma.h | 26 -
arch/arm/mach-s5pv210/include/mach/gpio.h | 140 --
arch/arm/mach-s5pv210/include/mach/hardware.h | 18 -
arch/arm/mach-s5pv210/include/mach/irqs.h | 137 --
arch/arm/mach-s5pv210/include/mach/map.h | 158 ---
arch/arm/mach-s5pv210/include/mach/memory.h | 27 -
arch/arm/mach-s5pv210/include/mach/pm-core.h | 46 -
arch/arm/mach-s5pv210/include/mach/regs-clock.h | 2 +-
arch/arm/mach-s5pv210/include/mach/regs-gpio.h | 41 -
arch/arm/mach-s5pv210/include/mach/regs-irq.h | 18 -
arch/arm/mach-s5pv210/mach-aquila.c | 687 ----------
arch/arm/mach-s5pv210/mach-goni.c | 916 -------------
arch/arm/mach-s5pv210/mach-smdkc110.c | 159 ---
arch/arm/mach-s5pv210/mach-smdkv210.c | 337 -----
arch/arm/mach-s5pv210/mach-torbreck.c | 135 --
arch/arm/mach-s5pv210/pm.c | 147 ++-
arch/arm/mach-s5pv210/s5pv210.c | 77 ++
arch/arm/mach-s5pv210/setup-fb-24bpp.c | 49 -
arch/arm/mach-s5pv210/setup-fimc.c | 43 -
arch/arm/mach-s5pv210/setup-i2c0.c | 28 -
arch/arm/mach-s5pv210/setup-i2c1.c | 28 -
arch/arm/mach-s5pv210/setup-i2c2.c | 28 -
arch/arm/mach-s5pv210/setup-ide.c | 39 -
arch/arm/mach-s5pv210/setup-keypad.c | 24 -
arch/arm/mach-s5pv210/setup-sdhci-gpio.c | 103 --
arch/arm/mach-s5pv210/setup-spi.c | 34 -
arch/arm/mach-s5pv210/setup-usb-phy.c | 95 --
arch/arm/mach-s5pv210/sleep.S | 36 +
arch/arm/plat-samsung/Kconfig | 143 +-
arch/arm/plat-samsung/Makefile | 15 -
arch/arm/plat-samsung/clock-clksrc.c | 212 ---
arch/arm/plat-samsung/clock.c | 539 --------
arch/arm/plat-samsung/cpu.c | 3 +-
arch/arm/plat-samsung/devs.c | 330 -----
arch/arm/plat-samsung/include/plat/camport.h | 28 -
arch/arm/plat-samsung/include/plat/clock-clksrc.h | 83 --
arch/arm/plat-samsung/include/plat/clock.h | 152 ---
arch/arm/plat-samsung/include/plat/cpu-freq-core.h | 3 -
arch/arm/plat-samsung/include/plat/cpu.h | 13 -
arch/arm/plat-samsung/include/plat/devs.h | 42 -
arch/arm/plat-samsung/include/plat/fb-core.h | 15 -
arch/arm/plat-samsung/include/plat/fb.h | 22 -
arch/arm/plat-samsung/include/plat/fimc-core.h | 51 -
arch/arm/plat-samsung/include/plat/gpio-cfg.h | 64 -
arch/arm/plat-samsung/include/plat/hdmi.h | 16 -
arch/arm/plat-samsung/include/plat/irqs.h | 72 --
arch/arm/plat-samsung/include/plat/mfc.h | 35 -
arch/arm/plat-samsung/include/plat/pll.h | 323 -----
arch/arm/plat-samsung/include/plat/s5p-clock.h | 65 -
arch/arm/plat-samsung/include/plat/sdhci.h | 47 -
arch/arm/plat-samsung/include/plat/tv-core.h | 44 -
arch/arm/plat-samsung/init.c | 1 -
arch/arm/plat-samsung/pm-gpio.c | 4 +-
arch/arm/plat-samsung/s5p-clock.c | 294 -----
arch/arm/plat-samsung/s5p-dev-mfc.c | 81 +-
arch/arm/plat-samsung/s5p-dev-uart.c | 88 --
arch/arm/plat-samsung/s5p-irq-eint.c | 221 ----
arch/arm/plat-samsung/s5p-irq-gpioint.c | 218 ----
arch/arm/plat-samsung/s5p-irq-pm.c | 92 --
arch/arm/plat-samsung/s5p-irq.c | 31 -
arch/arm/plat-samsung/s5p-pm.c | 40 -
arch/arm/plat-samsung/s5p-sleep.S | 45 -
drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-s5pv210-audss.c | 241 ++++
drivers/clk/samsung/clk-s5pv210.c | 856 ++++++++++++
drivers/cpufreq/s3c2410-cpufreq.c | 2 -
drivers/cpufreq/s3c2412-cpufreq.c | 3 -
drivers/cpufreq/s3c2440-cpufreq.c | 3 -
drivers/cpufreq/s3c24xx-cpufreq.c | 1 -
drivers/cpufreq/s5pv210-cpufreq.c | 131 +-
drivers/gpio/gpio-samsung.c | 240 ----
drivers/phy/Kconfig | 10 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-s5pv210-usb2.c | 187 +++
drivers/phy/phy-samsung-usb2.c | 6 +
drivers/phy/phy-samsung-usb2.h | 1 +
drivers/tty/serial/samsung.c | 4 -
include/dt-bindings/clock/s5pv210-audss.h | 34 +
include/dt-bindings/clock/s5pv210.h | 239 ++++
125 files changed, 4843 insertions(+), 9409 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt
create mode 100644 Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt
create mode 100644 arch/arm/boot/dts/s5pv210-aquila.dts
create mode 100644 arch/arm/boot/dts/s5pv210-goni.dts
create mode 100644 arch/arm/boot/dts/s5pv210-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/s5pv210-smdkc110.dts
create mode 100644 arch/arm/boot/dts/s5pv210-smdkv210.dts
create mode 100644 arch/arm/boot/dts/s5pv210-torbreck.dts
create mode 100644 arch/arm/boot/dts/s5pv210.dtsi
create mode 100644 arch/arm/include/debug/s5pv210.S
delete mode 100644 arch/arm/mach-s5pv210/Makefile.boot
delete mode 100644 arch/arm/mach-s5pv210/clock.c
delete mode 100644 arch/arm/mach-s5pv210/common.c
delete mode 100644 arch/arm/mach-s5pv210/dev-audio.c
delete mode 100644 arch/arm/mach-s5pv210/dma.c
delete mode 100644 arch/arm/mach-s5pv210/include/mach/debug-macro.S
delete mode 100644 arch/arm/mach-s5pv210/include/mach/dma.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/hardware.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/irqs.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/map.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/memory.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/pm-core.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-irq.h
delete mode 100644 arch/arm/mach-s5pv210/mach-aquila.c
delete mode 100644 arch/arm/mach-s5pv210/mach-goni.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkc110.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkv210.c
delete mode 100644 arch/arm/mach-s5pv210/mach-torbreck.c
create mode 100644 arch/arm/mach-s5pv210/s5pv210.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fb-24bpp.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fimc.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c0.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c1.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c2.c
delete mode 100644 arch/arm/mach-s5pv210/setup-ide.c
delete mode 100644 arch/arm/mach-s5pv210/setup-keypad.c
delete mode 100644 arch/arm/mach-s5pv210/setup-sdhci-gpio.c
delete mode 100644 arch/arm/mach-s5pv210/setup-spi.c
delete mode 100644 arch/arm/mach-s5pv210/setup-usb-phy.c
create mode 100644 arch/arm/mach-s5pv210/sleep.S
delete mode 100644 arch/arm/plat-samsung/clock-clksrc.c
delete mode 100644 arch/arm/plat-samsung/clock.c
delete mode 100644 arch/arm/plat-samsung/include/plat/camport.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock-clksrc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/fimc-core.h
delete mode 100644 arch/arm/plat-samsung/include/plat/hdmi.h
delete mode 100644 arch/arm/plat-samsung/include/plat/irqs.h
delete mode 100644 arch/arm/plat-samsung/include/plat/mfc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/pll.h
delete mode 100644 arch/arm/plat-samsung/include/plat/s5p-clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/tv-core.h
delete mode 100644 arch/arm/plat-samsung/s5p-clock.c
delete mode 100644 arch/arm/plat-samsung/s5p-dev-uart.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-eint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-gpioint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq.c
delete mode 100644 arch/arm/plat-samsung/s5p-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-sleep.S
create mode 100644 drivers/clk/samsung/clk-s5pv210-audss.c
create mode 100644 drivers/clk/samsung/clk-s5pv210.c
create mode 100644 drivers/phy/phy-s5pv210-usb2.c
create mode 100644 include/dt-bindings/clock/s5pv210-audss.h
create mode 100644 include/dt-bindings/clock/s5pv210.h
--
1.9.3
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-04 17:46 ` Tomasz Figa
0 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-04 17:46 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, linux-kernel, Kukjin Kim, Arnd Bergmann,
Olof Johansson, Marek Szyprowski, Mark Brown, Heiko Stübner,
Tomasz Figa, Tomasz Figa
This huge series is a (hopefully final) attempt to convert Samsung S5PV210
into a DT-only and multiplatform-aware platform. It consists of several
steps to gradually replace legacy code with one meeting current standards
and then finally remove unused remnants.
Patches 1-6 migrate the platform to fully use the Common Clock Framework
and get rid of legacy private clock code, of which s5pv210 was the last
user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
USB to be supported when using DT. Further three patches (8-10) add DT
support for mach-s5pv210 and necessary DT sources for currently supported
boards. Patch 11 removes board files and code directly related to them,
effectively making s5pv210 a DT-only platform. In next step, patches 12-15
prepare remaining code for multiplatform enablement, which is finally done
in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
unused code left after making the last S5P platform DT-only.
Build tested patch by patch on following configs:
- s3c2410_defconfig (with DT support enabled),
- s3c6400_defconfig (with DT support enabled),
- s5pv210_defconfig (with DT support enabled after patches adding it),
- exynos_defconfig,
- exynos_defconfig with S5PV210 enabled in multiplatform configuration.
Boot tested on s5pv210-goni board.
Note that support for smdkc110, smdkv210 and torbreck boards is provided
by moving data from existing board files to new device tree sources. No
testing was performed due to mentioned board not being available anymore.
However I believe we agreed on this approach, because apparently there
are no active users of them. See the RFC from August 2013 asking for
removal of the whole platform [1].
[1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
Mateusz Krawczuk (6):
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
ARM: s5pv210: Migrate clock handling to Common Clock Framework
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
ARM: s5pv210: Add board file for boot using Device Tree
ARM: Samsung: DT: Add Device tree for s5pv210
ARM: Samsung: DT: Add Device tree for S5PC110/S5PV210 Boards
Tomasz Figa (13):
cpufreq: s3c24xx: Remove some dead code
serial: samsung: Remove support for legacy clock code
ARM: SAMSUNG: Remove legacy clock code
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: S5PV210: Remove support for board files
ARM: S5PV210: Untie PM support from legacy code
ARM: s5pv210: move debug-macro.S into the common space
ARM: s5pv210: Register cpufreq platform device
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: s5pv210: Enable multi-platform build support
gpio: samsung: Remove legacy support of S5PV210
ARM: SAMSUNG: Remove remaining legacy code
clk: samsung: s5pv210: Remove legacy board support
.../bindings/clock/clk-s5pv210-audss.txt | 53 +
.../bindings/clock/samsung,s5pv210-clock.txt | 78 ++
.../devicetree/bindings/phy/samsung-phy.txt | 1 +
arch/arm/Kconfig | 22 +-
arch/arm/Kconfig.debug | 12 +-
arch/arm/Makefile | 4 +-
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/s5pv210-aquila.dts | 392 ++++++
arch/arm/boot/dts/s5pv210-goni.dts | 449 +++++++
arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 839 ++++++++++++
arch/arm/boot/dts/s5pv210-smdkc110.dts | 78 ++
arch/arm/boot/dts/s5pv210-smdkv210.dts | 238 ++++
arch/arm/boot/dts/s5pv210-torbreck.dts | 92 ++
arch/arm/boot/dts/s5pv210.dtsi | 633 +++++++++
arch/arm/include/debug/s5pv210.S | 34 +
arch/arm/mach-exynos/pm.c | 1 -
arch/arm/mach-s3c24xx/common.c | 2 -
arch/arm/mach-s3c24xx/iotiming-s3c2412.c | 1 -
arch/arm/mach-s3c24xx/mach-h1940.c | 5 +-
arch/arm/mach-s3c24xx/mach-jive.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2413.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2416.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2443.c | 1 -
arch/arm/mach-s3c24xx/mach-vstms.c | 1 -
arch/arm/mach-s3c24xx/s3c2410.c | 6 -
arch/arm/mach-s3c24xx/s3c2412.c | 6 -
arch/arm/mach-s3c24xx/s3c2442.c | 1 -
arch/arm/mach-s3c24xx/s3c244x.c | 6 -
arch/arm/mach-s3c64xx/mach-anw6410.c | 1 -
arch/arm/mach-s3c64xx/mach-crag6410.c | 1 -
arch/arm/mach-s3c64xx/mach-hmt.c | 1 -
arch/arm/mach-s3c64xx/mach-ncp.c | 1 -
arch/arm/mach-s3c64xx/mach-smartq.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6400.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6410.c | 1 -
arch/arm/mach-s3c64xx/s3c6400.c | 1 -
arch/arm/mach-s3c64xx/s3c6410.c | 1 -
arch/arm/mach-s5pv210/Kconfig | 197 +--
arch/arm/mach-s5pv210/Makefile | 29 +-
arch/arm/mach-s5pv210/Makefile.boot | 2 -
arch/arm/mach-s5pv210/clock.c | 1365 --------------------
arch/arm/mach-s5pv210/common.c | 279 ----
arch/arm/mach-s5pv210/common.h | 21 +-
arch/arm/mach-s5pv210/dev-audio.c | 246 ----
arch/arm/mach-s5pv210/dma.c | 130 --
arch/arm/mach-s5pv210/include/mach/debug-macro.S | 41 -
arch/arm/mach-s5pv210/include/mach/dma.h | 26 -
arch/arm/mach-s5pv210/include/mach/gpio.h | 140 --
arch/arm/mach-s5pv210/include/mach/hardware.h | 18 -
arch/arm/mach-s5pv210/include/mach/irqs.h | 137 --
arch/arm/mach-s5pv210/include/mach/map.h | 158 ---
arch/arm/mach-s5pv210/include/mach/memory.h | 27 -
arch/arm/mach-s5pv210/include/mach/pm-core.h | 46 -
arch/arm/mach-s5pv210/include/mach/regs-clock.h | 2 +-
arch/arm/mach-s5pv210/include/mach/regs-gpio.h | 41 -
arch/arm/mach-s5pv210/include/mach/regs-irq.h | 18 -
arch/arm/mach-s5pv210/mach-aquila.c | 687 ----------
arch/arm/mach-s5pv210/mach-goni.c | 916 -------------
arch/arm/mach-s5pv210/mach-smdkc110.c | 159 ---
arch/arm/mach-s5pv210/mach-smdkv210.c | 337 -----
arch/arm/mach-s5pv210/mach-torbreck.c | 135 --
arch/arm/mach-s5pv210/pm.c | 147 ++-
arch/arm/mach-s5pv210/s5pv210.c | 77 ++
arch/arm/mach-s5pv210/setup-fb-24bpp.c | 49 -
arch/arm/mach-s5pv210/setup-fimc.c | 43 -
arch/arm/mach-s5pv210/setup-i2c0.c | 28 -
arch/arm/mach-s5pv210/setup-i2c1.c | 28 -
arch/arm/mach-s5pv210/setup-i2c2.c | 28 -
arch/arm/mach-s5pv210/setup-ide.c | 39 -
arch/arm/mach-s5pv210/setup-keypad.c | 24 -
arch/arm/mach-s5pv210/setup-sdhci-gpio.c | 103 --
arch/arm/mach-s5pv210/setup-spi.c | 34 -
arch/arm/mach-s5pv210/setup-usb-phy.c | 95 --
arch/arm/mach-s5pv210/sleep.S | 36 +
arch/arm/plat-samsung/Kconfig | 143 +-
arch/arm/plat-samsung/Makefile | 15 -
arch/arm/plat-samsung/clock-clksrc.c | 212 ---
arch/arm/plat-samsung/clock.c | 539 --------
arch/arm/plat-samsung/cpu.c | 3 +-
arch/arm/plat-samsung/devs.c | 330 -----
arch/arm/plat-samsung/include/plat/camport.h | 28 -
arch/arm/plat-samsung/include/plat/clock-clksrc.h | 83 --
arch/arm/plat-samsung/include/plat/clock.h | 152 ---
arch/arm/plat-samsung/include/plat/cpu-freq-core.h | 3 -
arch/arm/plat-samsung/include/plat/cpu.h | 13 -
arch/arm/plat-samsung/include/plat/devs.h | 42 -
arch/arm/plat-samsung/include/plat/fb-core.h | 15 -
arch/arm/plat-samsung/include/plat/fb.h | 22 -
arch/arm/plat-samsung/include/plat/fimc-core.h | 51 -
arch/arm/plat-samsung/include/plat/gpio-cfg.h | 64 -
arch/arm/plat-samsung/include/plat/hdmi.h | 16 -
arch/arm/plat-samsung/include/plat/irqs.h | 72 --
arch/arm/plat-samsung/include/plat/mfc.h | 35 -
arch/arm/plat-samsung/include/plat/pll.h | 323 -----
arch/arm/plat-samsung/include/plat/s5p-clock.h | 65 -
arch/arm/plat-samsung/include/plat/sdhci.h | 47 -
arch/arm/plat-samsung/include/plat/tv-core.h | 44 -
arch/arm/plat-samsung/init.c | 1 -
arch/arm/plat-samsung/pm-gpio.c | 4 +-
arch/arm/plat-samsung/s5p-clock.c | 294 -----
arch/arm/plat-samsung/s5p-dev-mfc.c | 81 +-
arch/arm/plat-samsung/s5p-dev-uart.c | 88 --
arch/arm/plat-samsung/s5p-irq-eint.c | 221 ----
arch/arm/plat-samsung/s5p-irq-gpioint.c | 218 ----
arch/arm/plat-samsung/s5p-irq-pm.c | 92 --
arch/arm/plat-samsung/s5p-irq.c | 31 -
arch/arm/plat-samsung/s5p-pm.c | 40 -
arch/arm/plat-samsung/s5p-sleep.S | 45 -
drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-s5pv210-audss.c | 241 ++++
drivers/clk/samsung/clk-s5pv210.c | 856 ++++++++++++
drivers/cpufreq/s3c2410-cpufreq.c | 2 -
drivers/cpufreq/s3c2412-cpufreq.c | 3 -
drivers/cpufreq/s3c2440-cpufreq.c | 3 -
drivers/cpufreq/s3c24xx-cpufreq.c | 1 -
drivers/cpufreq/s5pv210-cpufreq.c | 131 +-
drivers/gpio/gpio-samsung.c | 240 ----
drivers/phy/Kconfig | 10 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-s5pv210-usb2.c | 187 +++
drivers/phy/phy-samsung-usb2.c | 6 +
drivers/phy/phy-samsung-usb2.h | 1 +
drivers/tty/serial/samsung.c | 4 -
include/dt-bindings/clock/s5pv210-audss.h | 34 +
include/dt-bindings/clock/s5pv210.h | 239 ++++
125 files changed, 4843 insertions(+), 9409 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt
create mode 100644 Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt
create mode 100644 arch/arm/boot/dts/s5pv210-aquila.dts
create mode 100644 arch/arm/boot/dts/s5pv210-goni.dts
create mode 100644 arch/arm/boot/dts/s5pv210-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/s5pv210-smdkc110.dts
create mode 100644 arch/arm/boot/dts/s5pv210-smdkv210.dts
create mode 100644 arch/arm/boot/dts/s5pv210-torbreck.dts
create mode 100644 arch/arm/boot/dts/s5pv210.dtsi
create mode 100644 arch/arm/include/debug/s5pv210.S
delete mode 100644 arch/arm/mach-s5pv210/Makefile.boot
delete mode 100644 arch/arm/mach-s5pv210/clock.c
delete mode 100644 arch/arm/mach-s5pv210/common.c
delete mode 100644 arch/arm/mach-s5pv210/dev-audio.c
delete mode 100644 arch/arm/mach-s5pv210/dma.c
delete mode 100644 arch/arm/mach-s5pv210/include/mach/debug-macro.S
delete mode 100644 arch/arm/mach-s5pv210/include/mach/dma.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/hardware.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/irqs.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/map.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/memory.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/pm-core.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-irq.h
delete mode 100644 arch/arm/mach-s5pv210/mach-aquila.c
delete mode 100644 arch/arm/mach-s5pv210/mach-goni.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkc110.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkv210.c
delete mode 100644 arch/arm/mach-s5pv210/mach-torbreck.c
create mode 100644 arch/arm/mach-s5pv210/s5pv210.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fb-24bpp.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fimc.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c0.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c1.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c2.c
delete mode 100644 arch/arm/mach-s5pv210/setup-ide.c
delete mode 100644 arch/arm/mach-s5pv210/setup-keypad.c
delete mode 100644 arch/arm/mach-s5pv210/setup-sdhci-gpio.c
delete mode 100644 arch/arm/mach-s5pv210/setup-spi.c
delete mode 100644 arch/arm/mach-s5pv210/setup-usb-phy.c
create mode 100644 arch/arm/mach-s5pv210/sleep.S
delete mode 100644 arch/arm/plat-samsung/clock-clksrc.c
delete mode 100644 arch/arm/plat-samsung/clock.c
delete mode 100644 arch/arm/plat-samsung/include/plat/camport.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock-clksrc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/fimc-core.h
delete mode 100644 arch/arm/plat-samsung/include/plat/hdmi.h
delete mode 100644 arch/arm/plat-samsung/include/plat/irqs.h
delete mode 100644 arch/arm/plat-samsung/include/plat/mfc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/pll.h
delete mode 100644 arch/arm/plat-samsung/include/plat/s5p-clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/tv-core.h
delete mode 100644 arch/arm/plat-samsung/s5p-clock.c
delete mode 100644 arch/arm/plat-samsung/s5p-dev-uart.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-eint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-gpioint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq.c
delete mode 100644 arch/arm/plat-samsung/s5p-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-sleep.S
create mode 100644 drivers/clk/samsung/clk-s5pv210-audss.c
create mode 100644 drivers/clk/samsung/clk-s5pv210.c
create mode 100644 drivers/phy/phy-s5pv210-usb2.c
create mode 100644 include/dt-bindings/clock/s5pv210-audss.h
create mode 100644 include/dt-bindings/clock/s5pv210.h
--
1.9.3
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up
@ 2014-07-04 17:46 ` Tomasz Figa
0 siblings, 0 replies; 19+ messages in thread
From: Tomasz Figa @ 2014-07-04 17:46 UTC (permalink / raw)
To: linux-arm-kernel
This huge series is a (hopefully final) attempt to convert Samsung S5PV210
into a DT-only and multiplatform-aware platform. It consists of several
steps to gradually replace legacy code with one meeting current standards
and then finally remove unused remnants.
Patches 1-6 migrate the platform to fully use the Common Clock Framework
and get rid of legacy private clock code, of which s5pv210 was the last
user. Then patch 7 adds generic PHY driver for USB PHY on S5PV210 to allow
USB to be supported when using DT. Further three patches (8-10) add DT
support for mach-s5pv210 and necessary DT sources for currently supported
boards. Patch 11 removes board files and code directly related to them,
effectively making s5pv210 a DT-only platform. In next step, patches 12-15
prepare remaining code for multiplatform enablement, which is finally done
in patch 16. Patches 17-19 are a final clean-up, which remove a lot of
unused code left after making the last S5P platform DT-only.
Build tested patch by patch on following configs:
- s3c2410_defconfig (with DT support enabled),
- s3c6400_defconfig (with DT support enabled),
- s5pv210_defconfig (with DT support enabled after patches adding it),
- exynos_defconfig,
- exynos_defconfig with S5PV210 enabled in multiplatform configuration.
Boot tested on s5pv210-goni board.
Note that support for smdkc110, smdkv210 and torbreck boards is provided
by moving data from existing board files to new device tree sources. No
testing was performed due to mentioned board not being available anymore.
However I believe we agreed on this approach, because apparently there
are no active users of them. See the RFC from August 2013 asking for
removal of the whole platform [1].
[1] http://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg21882.html
Mateusz Krawczuk (6):
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
ARM: s5pv210: Migrate clock handling to Common Clock Framework
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
ARM: s5pv210: Add board file for boot using Device Tree
ARM: Samsung: DT: Add Device tree for s5pv210
ARM: Samsung: DT: Add Device tree for S5PC110/S5PV210 Boards
Tomasz Figa (13):
cpufreq: s3c24xx: Remove some dead code
serial: samsung: Remove support for legacy clock code
ARM: SAMSUNG: Remove legacy clock code
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: S5PV210: Remove support for board files
ARM: S5PV210: Untie PM support from legacy code
ARM: s5pv210: move debug-macro.S into the common space
ARM: s5pv210: Register cpufreq platform device
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: s5pv210: Enable multi-platform build support
gpio: samsung: Remove legacy support of S5PV210
ARM: SAMSUNG: Remove remaining legacy code
clk: samsung: s5pv210: Remove legacy board support
.../bindings/clock/clk-s5pv210-audss.txt | 53 +
.../bindings/clock/samsung,s5pv210-clock.txt | 78 ++
.../devicetree/bindings/phy/samsung-phy.txt | 1 +
arch/arm/Kconfig | 22 +-
arch/arm/Kconfig.debug | 12 +-
arch/arm/Makefile | 4 +-
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/s5pv210-aquila.dts | 392 ++++++
arch/arm/boot/dts/s5pv210-goni.dts | 449 +++++++
arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 839 ++++++++++++
arch/arm/boot/dts/s5pv210-smdkc110.dts | 78 ++
arch/arm/boot/dts/s5pv210-smdkv210.dts | 238 ++++
arch/arm/boot/dts/s5pv210-torbreck.dts | 92 ++
arch/arm/boot/dts/s5pv210.dtsi | 633 +++++++++
arch/arm/include/debug/s5pv210.S | 34 +
arch/arm/mach-exynos/pm.c | 1 -
arch/arm/mach-s3c24xx/common.c | 2 -
arch/arm/mach-s3c24xx/iotiming-s3c2412.c | 1 -
arch/arm/mach-s3c24xx/mach-h1940.c | 5 +-
arch/arm/mach-s3c24xx/mach-jive.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2413.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2416.c | 1 -
arch/arm/mach-s3c24xx/mach-smdk2443.c | 1 -
arch/arm/mach-s3c24xx/mach-vstms.c | 1 -
arch/arm/mach-s3c24xx/s3c2410.c | 6 -
arch/arm/mach-s3c24xx/s3c2412.c | 6 -
arch/arm/mach-s3c24xx/s3c2442.c | 1 -
arch/arm/mach-s3c24xx/s3c244x.c | 6 -
arch/arm/mach-s3c64xx/mach-anw6410.c | 1 -
arch/arm/mach-s3c64xx/mach-crag6410.c | 1 -
arch/arm/mach-s3c64xx/mach-hmt.c | 1 -
arch/arm/mach-s3c64xx/mach-ncp.c | 1 -
arch/arm/mach-s3c64xx/mach-smartq.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6400.c | 1 -
arch/arm/mach-s3c64xx/mach-smdk6410.c | 1 -
arch/arm/mach-s3c64xx/s3c6400.c | 1 -
arch/arm/mach-s3c64xx/s3c6410.c | 1 -
arch/arm/mach-s5pv210/Kconfig | 197 +--
arch/arm/mach-s5pv210/Makefile | 29 +-
arch/arm/mach-s5pv210/Makefile.boot | 2 -
arch/arm/mach-s5pv210/clock.c | 1365 --------------------
arch/arm/mach-s5pv210/common.c | 279 ----
arch/arm/mach-s5pv210/common.h | 21 +-
arch/arm/mach-s5pv210/dev-audio.c | 246 ----
arch/arm/mach-s5pv210/dma.c | 130 --
arch/arm/mach-s5pv210/include/mach/debug-macro.S | 41 -
arch/arm/mach-s5pv210/include/mach/dma.h | 26 -
arch/arm/mach-s5pv210/include/mach/gpio.h | 140 --
arch/arm/mach-s5pv210/include/mach/hardware.h | 18 -
arch/arm/mach-s5pv210/include/mach/irqs.h | 137 --
arch/arm/mach-s5pv210/include/mach/map.h | 158 ---
arch/arm/mach-s5pv210/include/mach/memory.h | 27 -
arch/arm/mach-s5pv210/include/mach/pm-core.h | 46 -
arch/arm/mach-s5pv210/include/mach/regs-clock.h | 2 +-
arch/arm/mach-s5pv210/include/mach/regs-gpio.h | 41 -
arch/arm/mach-s5pv210/include/mach/regs-irq.h | 18 -
arch/arm/mach-s5pv210/mach-aquila.c | 687 ----------
arch/arm/mach-s5pv210/mach-goni.c | 916 -------------
arch/arm/mach-s5pv210/mach-smdkc110.c | 159 ---
arch/arm/mach-s5pv210/mach-smdkv210.c | 337 -----
arch/arm/mach-s5pv210/mach-torbreck.c | 135 --
arch/arm/mach-s5pv210/pm.c | 147 ++-
arch/arm/mach-s5pv210/s5pv210.c | 77 ++
arch/arm/mach-s5pv210/setup-fb-24bpp.c | 49 -
arch/arm/mach-s5pv210/setup-fimc.c | 43 -
arch/arm/mach-s5pv210/setup-i2c0.c | 28 -
arch/arm/mach-s5pv210/setup-i2c1.c | 28 -
arch/arm/mach-s5pv210/setup-i2c2.c | 28 -
arch/arm/mach-s5pv210/setup-ide.c | 39 -
arch/arm/mach-s5pv210/setup-keypad.c | 24 -
arch/arm/mach-s5pv210/setup-sdhci-gpio.c | 103 --
arch/arm/mach-s5pv210/setup-spi.c | 34 -
arch/arm/mach-s5pv210/setup-usb-phy.c | 95 --
arch/arm/mach-s5pv210/sleep.S | 36 +
arch/arm/plat-samsung/Kconfig | 143 +-
arch/arm/plat-samsung/Makefile | 15 -
arch/arm/plat-samsung/clock-clksrc.c | 212 ---
arch/arm/plat-samsung/clock.c | 539 --------
arch/arm/plat-samsung/cpu.c | 3 +-
arch/arm/plat-samsung/devs.c | 330 -----
arch/arm/plat-samsung/include/plat/camport.h | 28 -
arch/arm/plat-samsung/include/plat/clock-clksrc.h | 83 --
arch/arm/plat-samsung/include/plat/clock.h | 152 ---
arch/arm/plat-samsung/include/plat/cpu-freq-core.h | 3 -
arch/arm/plat-samsung/include/plat/cpu.h | 13 -
arch/arm/plat-samsung/include/plat/devs.h | 42 -
arch/arm/plat-samsung/include/plat/fb-core.h | 15 -
arch/arm/plat-samsung/include/plat/fb.h | 22 -
arch/arm/plat-samsung/include/plat/fimc-core.h | 51 -
arch/arm/plat-samsung/include/plat/gpio-cfg.h | 64 -
arch/arm/plat-samsung/include/plat/hdmi.h | 16 -
arch/arm/plat-samsung/include/plat/irqs.h | 72 --
arch/arm/plat-samsung/include/plat/mfc.h | 35 -
arch/arm/plat-samsung/include/plat/pll.h | 323 -----
arch/arm/plat-samsung/include/plat/s5p-clock.h | 65 -
arch/arm/plat-samsung/include/plat/sdhci.h | 47 -
arch/arm/plat-samsung/include/plat/tv-core.h | 44 -
arch/arm/plat-samsung/init.c | 1 -
arch/arm/plat-samsung/pm-gpio.c | 4 +-
arch/arm/plat-samsung/s5p-clock.c | 294 -----
arch/arm/plat-samsung/s5p-dev-mfc.c | 81 +-
arch/arm/plat-samsung/s5p-dev-uart.c | 88 --
arch/arm/plat-samsung/s5p-irq-eint.c | 221 ----
arch/arm/plat-samsung/s5p-irq-gpioint.c | 218 ----
arch/arm/plat-samsung/s5p-irq-pm.c | 92 --
arch/arm/plat-samsung/s5p-irq.c | 31 -
arch/arm/plat-samsung/s5p-pm.c | 40 -
arch/arm/plat-samsung/s5p-sleep.S | 45 -
drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-s5pv210-audss.c | 241 ++++
drivers/clk/samsung/clk-s5pv210.c | 856 ++++++++++++
drivers/cpufreq/s3c2410-cpufreq.c | 2 -
drivers/cpufreq/s3c2412-cpufreq.c | 3 -
drivers/cpufreq/s3c2440-cpufreq.c | 3 -
drivers/cpufreq/s3c24xx-cpufreq.c | 1 -
drivers/cpufreq/s5pv210-cpufreq.c | 131 +-
drivers/gpio/gpio-samsung.c | 240 ----
drivers/phy/Kconfig | 10 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-s5pv210-usb2.c | 187 +++
drivers/phy/phy-samsung-usb2.c | 6 +
drivers/phy/phy-samsung-usb2.h | 1 +
drivers/tty/serial/samsung.c | 4 -
include/dt-bindings/clock/s5pv210-audss.h | 34 +
include/dt-bindings/clock/s5pv210.h | 239 ++++
125 files changed, 4843 insertions(+), 9409 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt
create mode 100644 Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt
create mode 100644 arch/arm/boot/dts/s5pv210-aquila.dts
create mode 100644 arch/arm/boot/dts/s5pv210-goni.dts
create mode 100644 arch/arm/boot/dts/s5pv210-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/s5pv210-smdkc110.dts
create mode 100644 arch/arm/boot/dts/s5pv210-smdkv210.dts
create mode 100644 arch/arm/boot/dts/s5pv210-torbreck.dts
create mode 100644 arch/arm/boot/dts/s5pv210.dtsi
create mode 100644 arch/arm/include/debug/s5pv210.S
delete mode 100644 arch/arm/mach-s5pv210/Makefile.boot
delete mode 100644 arch/arm/mach-s5pv210/clock.c
delete mode 100644 arch/arm/mach-s5pv210/common.c
delete mode 100644 arch/arm/mach-s5pv210/dev-audio.c
delete mode 100644 arch/arm/mach-s5pv210/dma.c
delete mode 100644 arch/arm/mach-s5pv210/include/mach/debug-macro.S
delete mode 100644 arch/arm/mach-s5pv210/include/mach/dma.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/hardware.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/irqs.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/map.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/memory.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/pm-core.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-gpio.h
delete mode 100644 arch/arm/mach-s5pv210/include/mach/regs-irq.h
delete mode 100644 arch/arm/mach-s5pv210/mach-aquila.c
delete mode 100644 arch/arm/mach-s5pv210/mach-goni.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkc110.c
delete mode 100644 arch/arm/mach-s5pv210/mach-smdkv210.c
delete mode 100644 arch/arm/mach-s5pv210/mach-torbreck.c
create mode 100644 arch/arm/mach-s5pv210/s5pv210.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fb-24bpp.c
delete mode 100644 arch/arm/mach-s5pv210/setup-fimc.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c0.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c1.c
delete mode 100644 arch/arm/mach-s5pv210/setup-i2c2.c
delete mode 100644 arch/arm/mach-s5pv210/setup-ide.c
delete mode 100644 arch/arm/mach-s5pv210/setup-keypad.c
delete mode 100644 arch/arm/mach-s5pv210/setup-sdhci-gpio.c
delete mode 100644 arch/arm/mach-s5pv210/setup-spi.c
delete mode 100644 arch/arm/mach-s5pv210/setup-usb-phy.c
create mode 100644 arch/arm/mach-s5pv210/sleep.S
delete mode 100644 arch/arm/plat-samsung/clock-clksrc.c
delete mode 100644 arch/arm/plat-samsung/clock.c
delete mode 100644 arch/arm/plat-samsung/include/plat/camport.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock-clksrc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/fimc-core.h
delete mode 100644 arch/arm/plat-samsung/include/plat/hdmi.h
delete mode 100644 arch/arm/plat-samsung/include/plat/irqs.h
delete mode 100644 arch/arm/plat-samsung/include/plat/mfc.h
delete mode 100644 arch/arm/plat-samsung/include/plat/pll.h
delete mode 100644 arch/arm/plat-samsung/include/plat/s5p-clock.h
delete mode 100644 arch/arm/plat-samsung/include/plat/tv-core.h
delete mode 100644 arch/arm/plat-samsung/s5p-clock.c
delete mode 100644 arch/arm/plat-samsung/s5p-dev-uart.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-eint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-gpioint.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-irq.c
delete mode 100644 arch/arm/plat-samsung/s5p-pm.c
delete mode 100644 arch/arm/plat-samsung/s5p-sleep.S
create mode 100644 drivers/clk/samsung/clk-s5pv210-audss.c
create mode 100644 drivers/clk/samsung/clk-s5pv210.c
create mode 100644 drivers/phy/phy-s5pv210-usb2.c
create mode 100644 include/dt-bindings/clock/s5pv210-audss.h
create mode 100644 include/dt-bindings/clock/s5pv210.h
--
1.9.3
^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2014-07-12 22:57 UTC | newest]
Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-07-04 17:44 [PATCH 00/19] ARM: SAMSUNG: S5PV210 platform clean-up Tomasz Figa
2014-07-04 17:44 ` Tomasz Figa
2014-07-05 4:46 ` Viresh Kumar
2014-07-05 4:46 ` Viresh Kumar
2014-07-05 11:00 ` Tomasz Figa
2014-07-05 11:00 ` Tomasz Figa
2014-07-05 11:05 ` Heiko Stübner
2014-07-05 11:05 ` Heiko Stübner
2014-07-05 11:05 ` Heiko Stübner
2014-07-04 17:46 Tomasz Figa
2014-07-04 17:46 ` Tomasz Figa
2014-07-04 17:48 Tomasz Figa
2014-07-04 17:48 ` Tomasz Figa
2014-07-04 17:53 ` Tomasz Figa
2014-07-04 17:53 ` Tomasz Figa
2014-07-04 20:15 ` Arnd Bergmann
2014-07-04 20:15 ` Arnd Bergmann
2014-07-12 22:57 ` Kukjin Kim
2014-07-12 22:57 ` Kukjin Kim
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.