Re: [PATCH v3 02/14] cxl/region: Introduce concept of region configuration

From: Dan Williams <dan.j.williams@intel.com>
To: Ben Widawsky <ben.widawsky@intel.com>
Cc: linux-cxl@vger.kernel.org, patches@lists.linux.dev,
	 kernel test robot <lkp@intel.com>,
	Alison Schofield <alison.schofield@intel.com>,
	 Ira Weiny <ira.weiny@intel.com>,
	Jonathan Cameron <Jonathan.Cameron@huawei.com>,
	 Vishal Verma <vishal.l.verma@intel.com>,
	Bjorn Helgaas <helgaas@kernel.org>,
	 Linux NVDIMM <nvdimm@lists.linux.dev>,
	Linux PCI <linux-pci@vger.kernel.org>
Subject: Re: [PATCH v3 02/14] cxl/region: Introduce concept of region configuration
Date: Wed, 23 Feb 2022 14:24:00 -0800	[thread overview]
Message-ID: <CAPcyv4iqd-_37kfL0_UMq+17tt==P1Nq1yWFZkcJQ42A+03O7w@mail.gmail.com> (raw)
In-Reply-To: <20220223214955.riljjquteodtdyaj@intel.com>

On Wed, Feb 23, 2022 at 1:50 PM Ben Widawsky <ben.widawsky@intel.com> wrote:
>
> On 22-02-17 11:57:59, Dan Williams wrote:
> > On Thu, Feb 17, 2022 at 10:36 AM Ben Widawsky <ben.widawsky@intel.com> wrote:
> > >
> > > Consolidating earlier discussions...
> > >
> > > On 22-01-28 16:25:34, Dan Williams wrote:
> > > > On Thu, Jan 27, 2022 at 4:27 PM Ben Widawsky <ben.widawsky@intel.com> wrote:
> > > > >
> > > > > The region creation APIs create a vacant region. Configuring the region
> > > > > works in the same way as similar subsystems such as devdax. Sysfs attrs
> > > > > will be provided to allow userspace to configure the region.  Finally
> > > > > once all configuration is complete, userspace may activate the region.
> > > > >
> > > > > Introduced here are the most basic attributes needed to configure a
> > > > > region. Details of these attribute are described in the ABI
> > > >
> > > > s/attribute/attributes/
> > > >
> > > > > Documentation. Sanity checking of configuration parameters are done at
> > > > > region binding time. This consolidates all such logic in one place,
> > > > > rather than being strewn across multiple places.
> > > >
> > > > I think that's too late for some of the validation. The complex
> > > > validation that the region driver does throughout the topology is
> > > > different from the basic input validation that can  be done at the
> > > > sysfs write time. For example ,this patch allows negative
> > > > interleave_granularity values to specified, just return -EINVAL. I
> > > > agree that sysfs should not validate everything, I disagree with
> > > > pushing all validation to cxl_region_probe().
> > > >
> > >
> > > Okay. It might save us some back and forth if you could outline everything you'd
> > > expect to be validated, but I can also make an attempt to figure out the
> > > reasonable set of things.
> >
> > Input validation. Every value that gets written to a sysfs attribute
> > should be checked for validity, more below:
> >
> > >
> > > > >
> > > > > A example is provided below:
> > > > >
> > > > > /sys/bus/cxl/devices/region0.0:0
> > > > > ├── interleave_granularity
> >
> > ...validate granularity is within spec and can be supported by the root decoder.
> >
> > > > > ├── interleave_ways
> >
> > ...validate ways is within spec and can be supported by the root decoder.
>
> I'm not sure how to do this one. Validation requires device positions and we
> can't set the targets until ways is set. Can you please provide some more
> insight on what you'd like me to check in addition to the value being within
> spec?

For example you could check that interleave_ways is >= to the root
level interleave. I.e. it would be invalid to attempt a x1 interleave
on a decoder that is x2 interleaved at the host-bridge level.