[PATCH v3 0/3] exynos: arch: add support for exynos5260 SoC

[PATCH v3 0/3] exynos: arch: add support for exynos5260 SoC

[Rahul Sharma]

From: Rahul Sharma <Rahul.Sharma@samsung.com>

V3:
  1) Addressed review comments from Tomasz figa.

V2:
  1) Split up DT patch into SoC and Board patch.

This series is dependent on Sachin's patch
"ARM: EXYNOS: Consolidate CPU init code" at
http://comments.gmane.org/gmane.linux.kernel.samsung-soc/26560

This series is based on Kukjin's for-next branch at
http://git.kernel.org/?p=linux/kernel/git/kgene/linux-samsung.git

Pankaj Dubey (1):
  ARM: EXYNOS: initial board support for exynos5260 SoC

Rahul Sharma (2):
  ARM: dts: add dts files for exynos5260 SoC
  ARM: dts: add dts files for xyref5260 board

 arch/arm/boot/dts/Makefile                      |    1 +
 arch/arm/boot/dts/exynos5260-pinctrl.dtsi       |  574 +++++++++++++++++++++++
 arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts |  105 +++++
 arch/arm/boot/dts/exynos5260.dtsi               |  304 ++++++++++++
 arch/arm/mach-exynos/Kconfig                    |    9 +
 arch/arm/mach-exynos/common.c                   |   11 +
 arch/arm/mach-exynos/include/mach/map.h         |    1 +
 arch/arm/mach-exynos/mach-exynos5-dt.c          |    1 +
 arch/arm/plat-samsung/include/plat/cpu.h        |    8 +
 9 files changed, 1014 insertions(+)
 create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi
 create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
 create mode 100644 arch/arm/boot/dts/exynos5260.dtsi

-- 
1.7.9.5

[PATCH v3 0/3] exynos: arch: add support for exynos5260 SoC

[Rahul Sharma]

From: Rahul Sharma <Rahul.Sharma@samsung.com>

V3:
  1) Addressed review comments from Tomasz figa.

V2:
  1) Split up DT patch into SoC and Board patch.

This series is dependent on Sachin's patch
"ARM: EXYNOS: Consolidate CPU init code" at
http://comments.gmane.org/gmane.linux.kernel.samsung-soc/26560

This series is based on Kukjin's for-next branch at
http://git.kernel.org/?p=linux/kernel/git/kgene/linux-samsung.git

Pankaj Dubey (1):
  ARM: EXYNOS: initial board support for exynos5260 SoC

Rahul Sharma (2):
  ARM: dts: add dts files for exynos5260 SoC
  ARM: dts: add dts files for xyref5260 board

 arch/arm/boot/dts/Makefile                      |    1 +
 arch/arm/boot/dts/exynos5260-pinctrl.dtsi       |  574 +++++++++++++++++++++++
 arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts |  105 +++++
 arch/arm/boot/dts/exynos5260.dtsi               |  304 ++++++++++++
 arch/arm/mach-exynos/Kconfig                    |    9 +
 arch/arm/mach-exynos/common.c                   |   11 +
 arch/arm/mach-exynos/include/mach/map.h         |    1 +
 arch/arm/mach-exynos/mach-exynos5-dt.c          |    1 +
 arch/arm/plat-samsung/include/plat/cpu.h        |    8 +
 9 files changed, 1014 insertions(+)
 create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi
 create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
 create mode 100644 arch/arm/boot/dts/exynos5260.dtsi

-- 
1.7.9.5

[PATCH v3 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC

[Rahul Sharma]

From: Pankaj Dubey <pankaj.dubey@samsung.com>

This patch add basic arch side support for exynos5260 SoC.

Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
---
 arch/arm/mach-exynos/Kconfig             |    9 +++++++++
 arch/arm/mach-exynos/common.c            |   11 +++++++++++
 arch/arm/mach-exynos/include/mach/map.h  |    1 +
 arch/arm/mach-exynos/mach-exynos5-dt.c   |    1 +
 arch/arm/plat-samsung/include/plat/cpu.h |    8 ++++++++
 5 files changed, 30 insertions(+)

diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index 4c414af..5c96248 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -91,6 +91,15 @@ config SOC_EXYNOS5250
 	help
 	  Enable EXYNOS5250 SoC support
 
+config SOC_EXYNOS5260
+	bool "SAMSUNG EXYNOS5260"
+	default y
+	depends on ARCH_EXYNOS5
+	select AUTO_ZRELADDR
+	select SAMSUNG_DMADEV
+	help
+	  Enable EXYNOS5260 SoC support
+
 config SOC_EXYNOS5420
 	bool "SAMSUNG EXYNOS5420"
 	default y
diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c
index bab52ca..02b142d 100644
--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -176,6 +176,15 @@ static struct map_desc exynos5250_iodesc[] __initdata = {
 	},
 };
 
+static struct map_desc exynos5260_iodesc[] __initdata = {
+	{
+		.virtual	= (unsigned long)S5P_VA_SYSRAM_NS,
+		.pfn		= __phys_to_pfn(EXYNOS5260_PA_SYSRAM_NS),
+		.length		= SZ_4K,
+		.type		= MT_DEVICE,
+	},
+};
+
 static struct map_desc exynos5_iodesc[] __initdata = {
 	{
 		.virtual	= (unsigned long)S3C_VA_SYS,
@@ -326,6 +335,8 @@ static void __init exynos_map_io(void)
 		iotable_init(exynos4x12_iodesc, ARRAY_SIZE(exynos4x12_iodesc));
 	if (soc_is_exynos5250())
 		iotable_init(exynos5250_iodesc, ARRAY_SIZE(exynos5250_iodesc));
+	if (soc_is_exynos5260())
+		iotable_init(exynos5260_iodesc, ARRAY_SIZE(exynos5260_iodesc));
 }
 
 struct bus_type exynos_subsys = {
diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h
index 7b046b5..bd6fa02 100644
--- a/arch/arm/mach-exynos/include/mach/map.h
+++ b/arch/arm/mach-exynos/include/mach/map.h
@@ -29,6 +29,7 @@
 #define EXYNOS4210_PA_SYSRAM_NS		0x0203F000
 #define EXYNOS4x12_PA_SYSRAM_NS		0x0204F000
 #define EXYNOS5250_PA_SYSRAM_NS		0x0204F000
+#define EXYNOS5260_PA_SYSRAM_NS		0x02073000
 
 #define EXYNOS_PA_CHIPID		0x10000000
 
diff --git a/arch/arm/mach-exynos/mach-exynos5-dt.c b/arch/arm/mach-exynos/mach-exynos5-dt.c
index 65a4646..18aee57 100644
--- a/arch/arm/mach-exynos/mach-exynos5-dt.c
+++ b/arch/arm/mach-exynos/mach-exynos5-dt.c
@@ -50,6 +50,7 @@ static void __init exynos5_dt_machine_init(void)
 
 static char const *exynos5_dt_compat[] __initdata = {
 	"samsung,exynos5250",
+	"samsung,exynos5260",
 	"samsung,exynos5420",
 	"samsung,exynos5440",
 	NULL
diff --git a/arch/arm/plat-samsung/include/plat/cpu.h b/arch/arm/plat-samsung/include/plat/cpu.h
index 335beb3..60687aa 100644
--- a/arch/arm/plat-samsung/include/plat/cpu.h
+++ b/arch/arm/plat-samsung/include/plat/cpu.h
@@ -46,6 +46,7 @@ extern unsigned long samsung_cpu_id;
 #define EXYNOS4_CPU_MASK	0xFFFE0000
 
 #define EXYNOS5250_SOC_ID	0x43520000
+#define EXYNOS5260_SOC_ID	0xE5260000
 #define EXYNOS5420_SOC_ID	0xE5420000
 #define EXYNOS5440_SOC_ID	0xE5440000
 #define EXYNOS5_SOC_MASK	0xFFFFF000
@@ -68,6 +69,7 @@ IS_SAMSUNG_CPU(exynos4210, EXYNOS4210_CPU_ID, EXYNOS4_CPU_MASK)
 IS_SAMSUNG_CPU(exynos4212, EXYNOS4212_CPU_ID, EXYNOS4_CPU_MASK)
 IS_SAMSUNG_CPU(exynos4412, EXYNOS4412_CPU_ID, EXYNOS4_CPU_MASK)
 IS_SAMSUNG_CPU(exynos5250, EXYNOS5250_SOC_ID, EXYNOS5_SOC_MASK)
+IS_SAMSUNG_CPU(exynos5260, EXYNOS5260_SOC_ID, EXYNOS5_SOC_MASK)
 IS_SAMSUNG_CPU(exynos5420, EXYNOS5420_SOC_ID, EXYNOS5_SOC_MASK)
 IS_SAMSUNG_CPU(exynos5440, EXYNOS5440_SOC_ID, EXYNOS5_SOC_MASK)
 
@@ -148,6 +150,12 @@ IS_SAMSUNG_CPU(exynos5440, EXYNOS5440_SOC_ID, EXYNOS5_SOC_MASK)
 # define soc_is_exynos5250()	0
 #endif
 
+#if defined(CONFIG_SOC_EXYNOS5260)
+# define soc_is_exynos5260()	is_samsung_exynos5260()
+#else
+# define soc_is_exynos5260()	0
+#endif
+
 #if defined(CONFIG_SOC_EXYNOS5420)
 # define soc_is_exynos5420()	is_samsung_exynos5420()
 #else
-- 
1.7.9.5

[PATCH v3 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC

[Rahul Sharma]

From: Pankaj Dubey <pankaj.dubey@samsung.com>

This patch add basic arch side support for exynos5260 SoC.

Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
---
 arch/arm/mach-exynos/Kconfig             |    9 +++++++++
 arch/arm/mach-exynos/common.c            |   11 +++++++++++
 arch/arm/mach-exynos/include/mach/map.h  |    1 +
 arch/arm/mach-exynos/mach-exynos5-dt.c   |    1 +
 arch/arm/plat-samsung/include/plat/cpu.h |    8 ++++++++
 5 files changed, 30 insertions(+)

diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index 4c414af..5c96248 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -91,6 +91,15 @@ config SOC_EXYNOS5250
 	help
 	  Enable EXYNOS5250 SoC support
 
+config SOC_EXYNOS5260
+	bool "SAMSUNG EXYNOS5260"
+	default y
+	depends on ARCH_EXYNOS5
+	select AUTO_ZRELADDR
+	select SAMSUNG_DMADEV
+	help
+	  Enable EXYNOS5260 SoC support
+
 config SOC_EXYNOS5420
 	bool "SAMSUNG EXYNOS5420"
 	default y
diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c
index bab52ca..02b142d 100644
--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -176,6 +176,15 @@ static struct map_desc exynos5250_iodesc[] __initdata = {
 	},
 };
 
+static struct map_desc exynos5260_iodesc[] __initdata = {
+	{
+		.virtual	= (unsigned long)S5P_VA_SYSRAM_NS,
+		.pfn		= __phys_to_pfn(EXYNOS5260_PA_SYSRAM_NS),
+		.length		= SZ_4K,
+		.type		= MT_DEVICE,
+	},
+};
+
 static struct map_desc exynos5_iodesc[] __initdata = {
 	{
 		.virtual	= (unsigned long)S3C_VA_SYS,
@@ -326,6 +335,8 @@ static void __init exynos_map_io(void)
 		iotable_init(exynos4x12_iodesc, ARRAY_SIZE(exynos4x12_iodesc));
 	if (soc_is_exynos5250())
 		iotable_init(exynos5250_iodesc, ARRAY_SIZE(exynos5250_iodesc));
+	if (soc_is_exynos5260())
+		iotable_init(exynos5260_iodesc, ARRAY_SIZE(exynos5260_iodesc));
 }
 
 struct bus_type exynos_subsys = {
diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h
index 7b046b5..bd6fa02 100644
--- a/arch/arm/mach-exynos/include/mach/map.h
+++ b/arch/arm/mach-exynos/include/mach/map.h
@@ -29,6 +29,7 @@
 #define EXYNOS4210_PA_SYSRAM_NS		0x0203F000
 #define EXYNOS4x12_PA_SYSRAM_NS		0x0204F000
 #define EXYNOS5250_PA_SYSRAM_NS		0x0204F000
+#define EXYNOS5260_PA_SYSRAM_NS		0x02073000
 
 #define EXYNOS_PA_CHIPID		0x10000000
 
diff --git a/arch/arm/mach-exynos/mach-exynos5-dt.c b/arch/arm/mach-exynos/mach-exynos5-dt.c
index 65a4646..18aee57 100644
--- a/arch/arm/mach-exynos/mach-exynos5-dt.c
+++ b/arch/arm/mach-exynos/mach-exynos5-dt.c
@@ -50,6 +50,7 @@ static void __init exynos5_dt_machine_init(void)
 
 static char const *exynos5_dt_compat[] __initdata = {
 	"samsung,exynos5250",
+	"samsung,exynos5260",
 	"samsung,exynos5420",
 	"samsung,exynos5440",
 	NULL
diff --git a/arch/arm/plat-samsung/include/plat/cpu.h b/arch/arm/plat-samsung/include/plat/cpu.h
index 335beb3..60687aa 100644
--- a/arch/arm/plat-samsung/include/plat/cpu.h
+++ b/arch/arm/plat-samsung/include/plat/cpu.h
@@ -46,6 +46,7 @@ extern unsigned long samsung_cpu_id;
 #define EXYNOS4_CPU_MASK	0xFFFE0000
 
 #define EXYNOS5250_SOC_ID	0x43520000
+#define EXYNOS5260_SOC_ID	0xE5260000
 #define EXYNOS5420_SOC_ID	0xE5420000
 #define EXYNOS5440_SOC_ID	0xE5440000
 #define EXYNOS5_SOC_MASK	0xFFFFF000
@@ -68,6 +69,7 @@ IS_SAMSUNG_CPU(exynos4210, EXYNOS4210_CPU_ID, EXYNOS4_CPU_MASK)
 IS_SAMSUNG_CPU(exynos4212, EXYNOS4212_CPU_ID, EXYNOS4_CPU_MASK)
 IS_SAMSUNG_CPU(exynos4412, EXYNOS4412_CPU_ID, EXYNOS4_CPU_MASK)
 IS_SAMSUNG_CPU(exynos5250, EXYNOS5250_SOC_ID, EXYNOS5_SOC_MASK)
+IS_SAMSUNG_CPU(exynos5260, EXYNOS5260_SOC_ID, EXYNOS5_SOC_MASK)
 IS_SAMSUNG_CPU(exynos5420, EXYNOS5420_SOC_ID, EXYNOS5_SOC_MASK)
 IS_SAMSUNG_CPU(exynos5440, EXYNOS5440_SOC_ID, EXYNOS5_SOC_MASK)
 
@@ -148,6 +150,12 @@ IS_SAMSUNG_CPU(exynos5440, EXYNOS5440_SOC_ID, EXYNOS5_SOC_MASK)
 # define soc_is_exynos5250()	0
 #endif
 
+#if defined(CONFIG_SOC_EXYNOS5260)
+# define soc_is_exynos5260()	is_samsung_exynos5260()
+#else
+# define soc_is_exynos5260()	0
+#endif
+
 #if defined(CONFIG_SOC_EXYNOS5420)
 # define soc_is_exynos5420()	is_samsung_exynos5420()
 #else
-- 
1.7.9.5

[PATCH v3 2/3] ARM: dts: add dts files for exynos5260 SoC

[Rahul Sharma]

The patch adds the dts files for exynos5260.

Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
---
 arch/arm/boot/dts/exynos5260-pinctrl.dtsi |  574 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/exynos5260.dtsi         |  304 +++++++++++++++
 2 files changed, 878 insertions(+)
 create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi
 create mode 100644 arch/arm/boot/dts/exynos5260.dtsi

diff --git a/arch/arm/boot/dts/exynos5260-pinctrl.dtsi b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
new file mode 100644
index 0000000..f6ee55e
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
@@ -0,0 +1,574 @@
+/*
+ * Samsung's Exynos5260 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos5260 SoC pin-mux and pin-config options are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define PIN_PULL_NONE	0
+#define PIN_PULL_DOWN	1
+#define PIN_PULL_UP	3
+
+&pinctrl_0 {
+	gpa0: gpa0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa1: gpa1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa2: gpa2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb0: gpb0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb1: gpb1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb2: gpb2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb3: gpb3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb4: gpb4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb5: gpb5 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd0: gpd0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd1: gpd1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd2: gpd2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe0: gpe0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe1: gpe1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf0: gpf0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf1: gpf1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpk0: gpk0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx0: gpx0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx1: gpx1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx2: gpx2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx3: gpx3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	uart0_data: uart0-data {
+		samsung,pins = "gpa0-0", "gpa0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart0_fctl: uart0-fctl {
+		samsung,pins = "gpa0-2", "gpa0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_data: uart1-data {
+		samsung,pins = "gpa1-0", "gpa1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_fctl: uart1-fctl {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart2_data: uart2-data {
+		samsung,pins = "gpa1-4", "gpa1-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi0_bus: spi0-bus {
+		samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi1_bus: spi1-bus {
+		samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	usb3_vbus0_en: usb3-vbus0-en {
+		samsung,pins = "gpa2-4";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2s1_bus: i2s1-bus {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+				"gpb0-4";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	pcm1_bus: pcm1-bus {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+				"gpb0-4";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spdif1_bus: spdif1-bus {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2";
+		samsung,pin-function = <4>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi2_bus: spi2-bus {
+		samsung,pins = "gpb1-0", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c0_hs_bus: i2c0-hs-bus {
+		samsung,pins = "gpb3-0", "gpb3-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c1_hs_bus: i2c1-hs-bus {
+		samsung,pins = "gpb3-2", "gpb3-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c2_hs_bus: i2c2-hs-bus {
+		samsung,pins = "gpb3-4", "gpb3-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c3_hs_bus: i2c3-hs-bus {
+		samsung,pins = "gpb3-6", "gpb3-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c4_bus: i2c4-bus {
+		samsung,pins = "gpb4-0", "gpb4-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c5_bus: i2c5-bus {
+		samsung,pins = "gpb4-2", "gpb4-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c6_bus: i2c6-bus {
+		samsung,pins = "gpb4-4", "gpb4-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c7_bus: i2c7-bus {
+		samsung,pins = "gpb4-6", "gpb4-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c8_bus: i2c8-bus {
+		samsung,pins = "gpb5-0", "gpb5-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c9_bus: i2c9-bus {
+		samsung,pins = "gpb5-2", "gpb5-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c10_bus: i2c10-bus {
+		samsung,pins = "gpb5-4", "gpb5-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c11_bus: i2c11-bus {
+		samsung,pins = "gpb5-6", "gpb5-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_gpio_a: cam-gpio-a {
+		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
+			"gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
+			"gpe1-0", "gpe1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_gpio_b: cam-gpio-b {
+		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
+			"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_i2c1_bus: cam-i2c1-bus {
+		samsung,pins = "gpf0-2", "gpf0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_i2c0_bus: cam-i2c0-bus {
+		samsung,pins = "gpf0-0", "gpf0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_spi0_bus: cam-spi0-bus {
+		samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_spi1_bus: cam-spi1-bus {
+		samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&pinctrl_1 {
+	gpc0: gpc0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc1: gpc1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc2: gpc2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc3: gpc3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc4: gpc4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd0_clk: sd0-clk {
+		samsung,pins = "gpc0-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_cmd: sd0-cmd {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus1: sd0-bus-width1 {
+		samsung,pins = "gpc0-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus4: sd0-bus-width4 {
+		samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus8: sd0-bus-width8 {
+		samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_rdqs: sd0-rdqs {
+		samsung,pins = "gpc0-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_clk: sd1-clk {
+		samsung,pins = "gpc1-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_cmd: sd1-cmd {
+		samsung,pins = "gpc1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus1: sd1-bus-width1 {
+		samsung,pins = "gpc1-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus4: sd1-bus-width4 {
+		samsung,pins = "gpc1-3", "gpc1-4", "gpc1-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus8: sd1-bus-width8 {
+		samsung,pins = "gpc4-0", "gpc4-1", "gpc4-2", "gpc4-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_clk: sd2-clk {
+		samsung,pins = "gpc2-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_cmd: sd2-cmd {
+		samsung,pins = "gpc2-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_cd: sd2-cd {
+		samsung,pins = "gpc2-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_bus1: sd2-bus-width1 {
+		samsung,pins = "gpc2-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_bus4: sd2-bus-width4 {
+		samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+};
+
+&pinctrl_2 {
+	gpz0: gpz0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpz1: gpz1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5260.dtsi b/arch/arm/boot/dts/exynos5260.dtsi
new file mode 100644
index 0000000..876e23f
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5260.dtsi
@@ -0,0 +1,304 @@
+/*
+ * SAMSUNG EXYNOS5260 SoC device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/clk/exynos5260-clk.h>
+
+/ {
+	compatible = "samsung,exynos5260";
+	interrupt-parent = <&gic>;
+
+	aliases {
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		pinctrl2 = &pinctrl_2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x0>;
+			cci-control-port = <&cci_control1>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x1>;
+			cci-control-port = <&cci_control1>;
+		};
+
+		cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x100>;
+			cci-control-port = <&cci_control0>;
+		};
+
+		cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x101>;
+			cci-control-port = <&cci_control0>;
+		};
+
+		cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x102>;
+			cci-control-port = <&cci_control0>;
+		};
+
+		cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x103>;
+			cci-control-port = <&cci_control0>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		clock_top: clock-controller@10010000 {
+			compatible = "samsung,exynos5260-clock-top";
+			reg = <0x10010000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_peri: clock-controller@10200000 {
+			compatible = "samsung,exynos5260-clock-peri";
+			reg = <0x10200000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_egl: clock-controller@10600000 {
+			compatible = "samsung,exynos5260-clock-egl";
+			reg = <0x10600000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_kfc: clock-controller@10700000 {
+			compatible = "samsung,exynos5260-clock-kfc";
+			reg = <0x10700000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_g2d: clock-controller@10A00000 {
+			compatible = "samsung,exynos5260-clock-g2d";
+			reg = <0x10A00000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_mif: clock-controller@10CE0000 {
+			compatible = "samsung,exynos5260-clock-mif";
+			reg = <0x10CE0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_mfc: clock-controller@11090000 {
+			compatible = "samsung,exynos5260-clock-mfc";
+			reg = <0x11090000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_g3d: clock-controller@11830000 {
+			compatible = "samsung,exynos5260-clock-g3d";
+			reg = <0x11830000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_fsys: clock-controller@122E0000 {
+			compatible = "samsung,exynos5260-clock-fsys";
+			reg = <0x122E0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_aud: clock-controller@128C0000 {
+			compatible = "samsung,exynos5260-clock-aud";
+			reg = <0x128C0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_isp: clock-controller@133C0000 {
+			compatible = "samsung,exynos5260-clock-isp";
+			reg = <0x133C0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_gscl: clock-controller@13F00000 {
+			compatible = "samsung,exynos5260-clock-gscl";
+			reg = <0x13F00000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_disp: clock-controller@14550000 {
+			compatible = "samsung,exynos5260-clock-disp";
+			reg = <0x14550000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		gic: interrupt-controller@10481000 {
+			compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-controller;
+			reg = <0x10481000 0x1000>,
+				<0x10482000 0x1000>,
+				<0x10484000 0x2000>,
+				<0x10486000 0x2000>;
+			interrupts = <1 9 0xf04>;
+		};
+
+		chipid: chipid@10000000 {
+			compatible = "samsung,exynos4210-chipid";
+			reg = <0x10000000 0x100>;
+		};
+
+		mct: mct@100B0000 {
+			compatible = "samsung,exynos4210-mct";
+			reg = <0x100B0000 0x1000>;
+			clocks = <&clock_top FIN_PLL>, <&clock_peri PERI_CLK_MCT>;
+			clock-names = "fin_pll", "mct";
+			interrupts = <0 104 0>, <0 105 0>, <0 106 0>,
+					<0 107 0>, <0 122 0>, <0 123 0>,
+					<0 124 0>, <0 125 0>, <0 126 0>,
+					<0 127 0>, <0 128 0>, <0 129 0>;
+		};
+
+		cci: cci@10F00000 {
+			compatible = "arm,cci-400";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x10F00000 0x1000>;
+			ranges = <0x0 0x10F00000 0x6000>;
+
+			cci_control0: slave-if@4000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x4000 0x1000>;
+			};
+
+			cci_control1: slave-if@5000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x5000 0x1000>;
+			};
+		};
+
+		pinctrl_0: pinctrl@11600000 {
+			compatible = "samsung,exynos5260-pinctrl";
+			reg = <0x11600000 0x1000>;
+			interrupts = <0 79 0>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos4210-wakeup-eint";
+				interrupt-parent = <&gic>;
+				interrupts = <0 32 0>;
+			};
+		};
+
+		pinctrl_1: pinctrl@12290000 {
+			compatible = "samsung,exynos5260-pinctrl";
+			reg = <0x12290000 0x1000>;
+			interrupts = <0 157 0>;
+		};
+
+		pinctrl_2: pinctrl@128B0000 {
+			compatible = "samsung,exynos5260-pinctrl";
+			reg = <0x128B0000 0x1000>;
+			interrupts = <0 243 0>;
+		};
+
+		uart0: serial@12C00000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C00000 0x100>;
+			interrupts = <0 146 0>;
+			clocks = <&clock_peri PERI_CLK_UART0>, <&clock_peri PERI_SCLK_UART0>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart1: serial@12C10000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C10000 0x100>;
+			interrupts = <0 147 0>;
+			clocks = <&clock_peri PERI_CLK_UART1>, <&clock_peri PERI_SCLK_UART1>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart2: serial@12C20000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C20000 0x100>;
+			interrupts = <0 148 0>;
+			clocks = <&clock_peri PERI_CLK_UART2>, <&clock_peri PERI_SCLK_UART2>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart3: serial@12860000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12860000 0x100>;
+			interrupts = <0 145 0>;
+			clocks = <&clock_aud AUD_CLK_AUD_UART>, <&clock_aud AUD_SCLK_AUD_UART>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		mmc_0: mmc0@12140000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12140000 0x2000>;
+			interrupts = <0 156 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_fsys FSYS_CLK_MMC0>, <&clock_top TOP_SCLK_MMC0>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <64>;
+			status = "disabled";
+		};
+
+		mmc_1: mmc1@12150000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12150000 0x2000>;
+			interrupts = <0 158 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_fsys FSYS_CLK_MMC1>, <&clock_top TOP_SCLK_MMC1>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <64>;
+			status = "disabled";
+		};
+
+		mmc_2: mmc2@12160000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12160000 0x2000>;
+			interrupts = <0 159 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_fsys FSYS_CLK_MMC2>, <&clock_top TOP_SCLK_MMC2>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <64>;
+			status = "disabled";
+		};
+	};
+};
+
+#include "exynos5260-pinctrl.dtsi"
-- 
1.7.9.5

[PATCH v3 2/3] ARM: dts: add dts files for exynos5260 SoC

[Rahul Sharma]

The patch adds the dts files for exynos5260.

Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
---
 arch/arm/boot/dts/exynos5260-pinctrl.dtsi |  574 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/exynos5260.dtsi         |  304 +++++++++++++++
 2 files changed, 878 insertions(+)
 create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi
 create mode 100644 arch/arm/boot/dts/exynos5260.dtsi

diff --git a/arch/arm/boot/dts/exynos5260-pinctrl.dtsi b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
new file mode 100644
index 0000000..f6ee55e
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
@@ -0,0 +1,574 @@
+/*
+ * Samsung's Exynos5260 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos5260 SoC pin-mux and pin-config options are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define PIN_PULL_NONE	0
+#define PIN_PULL_DOWN	1
+#define PIN_PULL_UP	3
+
+&pinctrl_0 {
+	gpa0: gpa0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa1: gpa1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa2: gpa2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb0: gpb0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb1: gpb1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb2: gpb2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb3: gpb3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb4: gpb4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb5: gpb5 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd0: gpd0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd1: gpd1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd2: gpd2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe0: gpe0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe1: gpe1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf0: gpf0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf1: gpf1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpk0: gpk0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx0: gpx0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx1: gpx1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx2: gpx2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx3: gpx3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	uart0_data: uart0-data {
+		samsung,pins = "gpa0-0", "gpa0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart0_fctl: uart0-fctl {
+		samsung,pins = "gpa0-2", "gpa0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_data: uart1-data {
+		samsung,pins = "gpa1-0", "gpa1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_fctl: uart1-fctl {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart2_data: uart2-data {
+		samsung,pins = "gpa1-4", "gpa1-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi0_bus: spi0-bus {
+		samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi1_bus: spi1-bus {
+		samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	usb3_vbus0_en: usb3-vbus0-en {
+		samsung,pins = "gpa2-4";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2s1_bus: i2s1-bus {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+				"gpb0-4";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	pcm1_bus: pcm1-bus {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+				"gpb0-4";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spdif1_bus: spdif1-bus {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2";
+		samsung,pin-function = <4>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi2_bus: spi2-bus {
+		samsung,pins = "gpb1-0", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c0_hs_bus: i2c0-hs-bus {
+		samsung,pins = "gpb3-0", "gpb3-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c1_hs_bus: i2c1-hs-bus {
+		samsung,pins = "gpb3-2", "gpb3-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c2_hs_bus: i2c2-hs-bus {
+		samsung,pins = "gpb3-4", "gpb3-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c3_hs_bus: i2c3-hs-bus {
+		samsung,pins = "gpb3-6", "gpb3-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c4_bus: i2c4-bus {
+		samsung,pins = "gpb4-0", "gpb4-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c5_bus: i2c5-bus {
+		samsung,pins = "gpb4-2", "gpb4-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c6_bus: i2c6-bus {
+		samsung,pins = "gpb4-4", "gpb4-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c7_bus: i2c7-bus {
+		samsung,pins = "gpb4-6", "gpb4-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c8_bus: i2c8-bus {
+		samsung,pins = "gpb5-0", "gpb5-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c9_bus: i2c9-bus {
+		samsung,pins = "gpb5-2", "gpb5-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c10_bus: i2c10-bus {
+		samsung,pins = "gpb5-4", "gpb5-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c11_bus: i2c11-bus {
+		samsung,pins = "gpb5-6", "gpb5-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_gpio_a: cam-gpio-a {
+		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
+			"gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
+			"gpe1-0", "gpe1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_gpio_b: cam-gpio-b {
+		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
+			"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_i2c1_bus: cam-i2c1-bus {
+		samsung,pins = "gpf0-2", "gpf0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_i2c0_bus: cam-i2c0-bus {
+		samsung,pins = "gpf0-0", "gpf0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_spi0_bus: cam-spi0-bus {
+		samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_spi1_bus: cam-spi1-bus {
+		samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&pinctrl_1 {
+	gpc0: gpc0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc1: gpc1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc2: gpc2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc3: gpc3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc4: gpc4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd0_clk: sd0-clk {
+		samsung,pins = "gpc0-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_cmd: sd0-cmd {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus1: sd0-bus-width1 {
+		samsung,pins = "gpc0-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus4: sd0-bus-width4 {
+		samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus8: sd0-bus-width8 {
+		samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_rdqs: sd0-rdqs {
+		samsung,pins = "gpc0-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_clk: sd1-clk {
+		samsung,pins = "gpc1-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_cmd: sd1-cmd {
+		samsung,pins = "gpc1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus1: sd1-bus-width1 {
+		samsung,pins = "gpc1-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus4: sd1-bus-width4 {
+		samsung,pins = "gpc1-3", "gpc1-4", "gpc1-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus8: sd1-bus-width8 {
+		samsung,pins = "gpc4-0", "gpc4-1", "gpc4-2", "gpc4-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_clk: sd2-clk {
+		samsung,pins = "gpc2-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_cmd: sd2-cmd {
+		samsung,pins = "gpc2-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_cd: sd2-cd {
+		samsung,pins = "gpc2-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_bus1: sd2-bus-width1 {
+		samsung,pins = "gpc2-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_bus4: sd2-bus-width4 {
+		samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+};
+
+&pinctrl_2 {
+	gpz0: gpz0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpz1: gpz1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5260.dtsi b/arch/arm/boot/dts/exynos5260.dtsi
new file mode 100644
index 0000000..876e23f
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5260.dtsi
@@ -0,0 +1,304 @@
+/*
+ * SAMSUNG EXYNOS5260 SoC device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/clk/exynos5260-clk.h>
+
+/ {
+	compatible = "samsung,exynos5260";
+	interrupt-parent = <&gic>;
+
+	aliases {
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		pinctrl2 = &pinctrl_2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x0>;
+			cci-control-port = <&cci_control1>;
+		};
+
+		cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x1>;
+			cci-control-port = <&cci_control1>;
+		};
+
+		cpu at 100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x100>;
+			cci-control-port = <&cci_control0>;
+		};
+
+		cpu at 101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x101>;
+			cci-control-port = <&cci_control0>;
+		};
+
+		cpu at 102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x102>;
+			cci-control-port = <&cci_control0>;
+		};
+
+		cpu at 103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x103>;
+			cci-control-port = <&cci_control0>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		clock_top: clock-controller at 10010000 {
+			compatible = "samsung,exynos5260-clock-top";
+			reg = <0x10010000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_peri: clock-controller at 10200000 {
+			compatible = "samsung,exynos5260-clock-peri";
+			reg = <0x10200000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_egl: clock-controller at 10600000 {
+			compatible = "samsung,exynos5260-clock-egl";
+			reg = <0x10600000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_kfc: clock-controller at 10700000 {
+			compatible = "samsung,exynos5260-clock-kfc";
+			reg = <0x10700000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_g2d: clock-controller at 10A00000 {
+			compatible = "samsung,exynos5260-clock-g2d";
+			reg = <0x10A00000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_mif: clock-controller at 10CE0000 {
+			compatible = "samsung,exynos5260-clock-mif";
+			reg = <0x10CE0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_mfc: clock-controller at 11090000 {
+			compatible = "samsung,exynos5260-clock-mfc";
+			reg = <0x11090000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_g3d: clock-controller at 11830000 {
+			compatible = "samsung,exynos5260-clock-g3d";
+			reg = <0x11830000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_fsys: clock-controller at 122E0000 {
+			compatible = "samsung,exynos5260-clock-fsys";
+			reg = <0x122E0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_aud: clock-controller at 128C0000 {
+			compatible = "samsung,exynos5260-clock-aud";
+			reg = <0x128C0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_isp: clock-controller at 133C0000 {
+			compatible = "samsung,exynos5260-clock-isp";
+			reg = <0x133C0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_gscl: clock-controller at 13F00000 {
+			compatible = "samsung,exynos5260-clock-gscl";
+			reg = <0x13F00000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_disp: clock-controller at 14550000 {
+			compatible = "samsung,exynos5260-clock-disp";
+			reg = <0x14550000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		gic: interrupt-controller at 10481000 {
+			compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-controller;
+			reg = <0x10481000 0x1000>,
+				<0x10482000 0x1000>,
+				<0x10484000 0x2000>,
+				<0x10486000 0x2000>;
+			interrupts = <1 9 0xf04>;
+		};
+
+		chipid: chipid at 10000000 {
+			compatible = "samsung,exynos4210-chipid";
+			reg = <0x10000000 0x100>;
+		};
+
+		mct: mct at 100B0000 {
+			compatible = "samsung,exynos4210-mct";
+			reg = <0x100B0000 0x1000>;
+			clocks = <&clock_top FIN_PLL>, <&clock_peri PERI_CLK_MCT>;
+			clock-names = "fin_pll", "mct";
+			interrupts = <0 104 0>, <0 105 0>, <0 106 0>,
+					<0 107 0>, <0 122 0>, <0 123 0>,
+					<0 124 0>, <0 125 0>, <0 126 0>,
+					<0 127 0>, <0 128 0>, <0 129 0>;
+		};
+
+		cci: cci at 10F00000 {
+			compatible = "arm,cci-400";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x10F00000 0x1000>;
+			ranges = <0x0 0x10F00000 0x6000>;
+
+			cci_control0: slave-if at 4000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x4000 0x1000>;
+			};
+
+			cci_control1: slave-if at 5000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x5000 0x1000>;
+			};
+		};
+
+		pinctrl_0: pinctrl at 11600000 {
+			compatible = "samsung,exynos5260-pinctrl";
+			reg = <0x11600000 0x1000>;
+			interrupts = <0 79 0>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos4210-wakeup-eint";
+				interrupt-parent = <&gic>;
+				interrupts = <0 32 0>;
+			};
+		};
+
+		pinctrl_1: pinctrl at 12290000 {
+			compatible = "samsung,exynos5260-pinctrl";
+			reg = <0x12290000 0x1000>;
+			interrupts = <0 157 0>;
+		};
+
+		pinctrl_2: pinctrl at 128B0000 {
+			compatible = "samsung,exynos5260-pinctrl";
+			reg = <0x128B0000 0x1000>;
+			interrupts = <0 243 0>;
+		};
+
+		uart0: serial at 12C00000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C00000 0x100>;
+			interrupts = <0 146 0>;
+			clocks = <&clock_peri PERI_CLK_UART0>, <&clock_peri PERI_SCLK_UART0>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart1: serial at 12C10000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C10000 0x100>;
+			interrupts = <0 147 0>;
+			clocks = <&clock_peri PERI_CLK_UART1>, <&clock_peri PERI_SCLK_UART1>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart2: serial at 12C20000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C20000 0x100>;
+			interrupts = <0 148 0>;
+			clocks = <&clock_peri PERI_CLK_UART2>, <&clock_peri PERI_SCLK_UART2>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart3: serial at 12860000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12860000 0x100>;
+			interrupts = <0 145 0>;
+			clocks = <&clock_aud AUD_CLK_AUD_UART>, <&clock_aud AUD_SCLK_AUD_UART>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		mmc_0: mmc0 at 12140000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12140000 0x2000>;
+			interrupts = <0 156 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_fsys FSYS_CLK_MMC0>, <&clock_top TOP_SCLK_MMC0>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <64>;
+			status = "disabled";
+		};
+
+		mmc_1: mmc1 at 12150000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12150000 0x2000>;
+			interrupts = <0 158 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_fsys FSYS_CLK_MMC1>, <&clock_top TOP_SCLK_MMC1>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <64>;
+			status = "disabled";
+		};
+
+		mmc_2: mmc2 at 12160000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12160000 0x2000>;
+			interrupts = <0 159 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_fsys FSYS_CLK_MMC2>, <&clock_top TOP_SCLK_MMC2>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <64>;
+			status = "disabled";
+		};
+	};
+};
+
+#include "exynos5260-pinctrl.dtsi"
-- 
1.7.9.5

[PATCH v3 3/3] ARM: dts: add dts files for xyref5260 board

[Rahul Sharma]

The patch adds the dts files for xyref5260 board which
is based on Exynos5260 Evt0 sample.

Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
---
 arch/arm/boot/dts/Makefile                      |    1 +
 arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts |  105 +++++++++++++++++++++++
 2 files changed, 106 insertions(+)
 create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index fa70ea2..c513a69 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -64,6 +64,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos5250-arndale.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
+	exynos5260-xyref5260-evt0.dtb \
 	exynos5420-arndale-octa.dtb \
 	exynos5420-smdk5420.dtb \
 	exynos5440-sd5v1.dtb \
diff --git a/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
new file mode 100644
index 0000000..c4efc1e
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
@@ -0,0 +1,105 @@
+/*
+ * SAMSUNG XYREF5260 EVT0 board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+#include "exynos5260.dtsi"
+
+/ {
+	model = "SAMSUNG XYREF5260 EVT0 board based on EXYNOS5260";
+	compatible = "samsung,xyref5260", "samsung,exynos5260";
+
+	memory {
+		reg = <0x20000000 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttySAC2,115200";
+	};
+
+	clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fin_pll: oscillator@0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			clock-frequency = <24000000>;
+			clock-output-names = "fin_pll";
+			#clock-cells = <0>;
+		};
+	};
+};
+
+&pinctrl_0 {
+	hdmi_hpd_irq: hdmi-hpd-irq {
+		samsung,pins = "gpx3-7";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&mmc_0 {
+	status = "okay";
+	num-slots = <1>;
+	broken-cd;
+	bypass-smu;
+	supports-highspeed;
+	supports-hs200-mode; /* 200 Mhz */
+	fifo-depth = <0x40>;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_rdqs &sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+	};
+};
+
+&mmc_2 {
+	status = "okay";
+	num-slots = <1>;
+	supports-highspeed;
+	fifo-depth = <0x40>;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+		disable-wp;
+	};
+};
-- 
1.7.9.5

[PATCH v3 3/3] ARM: dts: add dts files for xyref5260 board

[Rahul Sharma]

The patch adds the dts files for xyref5260 board which
is based on Exynos5260 Evt0 sample.

Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
---
 arch/arm/boot/dts/Makefile                      |    1 +
 arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts |  105 +++++++++++++++++++++++
 2 files changed, 106 insertions(+)
 create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index fa70ea2..c513a69 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -64,6 +64,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos5250-arndale.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
+	exynos5260-xyref5260-evt0.dtb \
 	exynos5420-arndale-octa.dtb \
 	exynos5420-smdk5420.dtb \
 	exynos5440-sd5v1.dtb \
diff --git a/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
new file mode 100644
index 0000000..c4efc1e
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
@@ -0,0 +1,105 @@
+/*
+ * SAMSUNG XYREF5260 EVT0 board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+#include "exynos5260.dtsi"
+
+/ {
+	model = "SAMSUNG XYREF5260 EVT0 board based on EXYNOS5260";
+	compatible = "samsung,xyref5260", "samsung,exynos5260";
+
+	memory {
+		reg = <0x20000000 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttySAC2,115200";
+	};
+
+	clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fin_pll: oscillator at 0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			clock-frequency = <24000000>;
+			clock-output-names = "fin_pll";
+			#clock-cells = <0>;
+		};
+	};
+};
+
+&pinctrl_0 {
+	hdmi_hpd_irq: hdmi-hpd-irq {
+		samsung,pins = "gpx3-7";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&mmc_0 {
+	status = "okay";
+	num-slots = <1>;
+	broken-cd;
+	bypass-smu;
+	supports-highspeed;
+	supports-hs200-mode; /* 200 Mhz */
+	fifo-depth = <0x40>;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_rdqs &sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+
+	slot at 0 {
+		reg = <0>;
+		bus-width = <8>;
+	};
+};
+
+&mmc_2 {
+	status = "okay";
+	num-slots = <1>;
+	supports-highspeed;
+	fifo-depth = <0x40>;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+
+	slot at 0 {
+		reg = <0>;
+		bus-width = <4>;
+		disable-wp;
+	};
+};
-- 
1.7.9.5

Re: [PATCH v3 3/3] ARM: dts: add dts files for xyref5260 board

[Tomasz Figa]

Hi Rahul,

The patch looks good, except one issue pointed inline.

On 14.02.2014 14:37, Rahul Sharma wrote:
> diff --git a/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
> new file mode 100644
> index 0000000..c4efc1e
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts

[snip]

> +&mmc_0 {
> +	status = "okay";
> +	num-slots = <1>;
> +	broken-cd;
> +	bypass-smu;
> +	supports-highspeed;
> +	supports-hs200-mode; /* 200 Mhz */
> +	fifo-depth = <0x40>;

This is a SoC-level property and it is already specified in your 
exynos5260.dtsi.

> +	card-detect-delay = <200>;
> +	samsung,dw-mshc-ciu-div = <3>;
> +	samsung,dw-mshc-sdr-timing = <0 4>;
> +	samsung,dw-mshc-ddr-timing = <0 2>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sd0_rdqs &sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
> +
> +	slot@0 {
> +		reg = <0>;
> +		bus-width = <8>;
> +	};
> +};
> +
> +&mmc_2 {
> +	status = "okay";
> +	num-slots = <1>;
> +	supports-highspeed;
> +	fifo-depth = <0x40>;

Ditto.

Best regards,
Tomasz

[PATCH v3 3/3] ARM: dts: add dts files for xyref5260 board

[Tomasz Figa]

Hi Rahul,

The patch looks good, except one issue pointed inline.

On 14.02.2014 14:37, Rahul Sharma wrote:
> diff --git a/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
> new file mode 100644
> index 0000000..c4efc1e
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts

[snip]

> +&mmc_0 {
> +	status = "okay";
> +	num-slots = <1>;
> +	broken-cd;
> +	bypass-smu;
> +	supports-highspeed;
> +	supports-hs200-mode; /* 200 Mhz */
> +	fifo-depth = <0x40>;

This is a SoC-level property and it is already specified in your 
exynos5260.dtsi.

> +	card-detect-delay = <200>;
> +	samsung,dw-mshc-ciu-div = <3>;
> +	samsung,dw-mshc-sdr-timing = <0 4>;
> +	samsung,dw-mshc-ddr-timing = <0 2>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sd0_rdqs &sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
> +
> +	slot at 0 {
> +		reg = <0>;
> +		bus-width = <8>;
> +	};
> +};
> +
> +&mmc_2 {
> +	status = "okay";
> +	num-slots = <1>;
> +	supports-highspeed;
> +	fifo-depth = <0x40>;

Ditto.

Best regards,
Tomasz

Re: [PATCH v3 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC

[Tomasz Figa]

Hi,

On 14.02.2014 14:37, Rahul Sharma wrote:
> From: Pankaj Dubey <pankaj.dubey@samsung.com>
>
> This patch add basic arch side support for exynos5260 SoC.
>
> Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
> Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
> ---
>   arch/arm/mach-exynos/Kconfig             |    9 +++++++++
>   arch/arm/mach-exynos/common.c            |   11 +++++++++++
>   arch/arm/mach-exynos/include/mach/map.h  |    1 +
>   arch/arm/mach-exynos/mach-exynos5-dt.c   |    1 +
>   arch/arm/plat-samsung/include/plat/cpu.h |    8 ++++++++
>   5 files changed, 30 insertions(+)

Reviewed-by: Tomasz Figa <t.figa@samsung.com>

Best regards,
Tomasz

[PATCH v3 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC

[Tomasz Figa]

Hi,

On 14.02.2014 14:37, Rahul Sharma wrote:
> From: Pankaj Dubey <pankaj.dubey@samsung.com>
>
> This patch add basic arch side support for exynos5260 SoC.
>
> Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
> Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
> ---
>   arch/arm/mach-exynos/Kconfig             |    9 +++++++++
>   arch/arm/mach-exynos/common.c            |   11 +++++++++++
>   arch/arm/mach-exynos/include/mach/map.h  |    1 +
>   arch/arm/mach-exynos/mach-exynos5-dt.c   |    1 +
>   arch/arm/plat-samsung/include/plat/cpu.h |    8 ++++++++
>   5 files changed, 30 insertions(+)

Reviewed-by: Tomasz Figa <t.figa@samsung.com>

Best regards,
Tomasz

Re: [PATCH v3 2/3] ARM: dts: add dts files for exynos5260 SoC

[Tomasz Figa]

Hi,

On 14.02.2014 14:37, Rahul Sharma wrote:
> The patch adds the dts files for exynos5260.
>
> Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
> Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
> ---
>   arch/arm/boot/dts/exynos5260-pinctrl.dtsi |  574 +++++++++++++++++++++++++++++
>   arch/arm/boot/dts/exynos5260.dtsi         |  304 +++++++++++++++
>   2 files changed, 878 insertions(+)
>   create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi
>   create mode 100644 arch/arm/boot/dts/exynos5260.dtsi

Reviewed-by: Tomasz Figa <t.figa@samsung.com>

Best regards,
Tomasz

[PATCH v3 2/3] ARM: dts: add dts files for exynos5260 SoC

[Tomasz Figa]

Hi,

On 14.02.2014 14:37, Rahul Sharma wrote:
> The patch adds the dts files for exynos5260.
>
> Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
> Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
> ---
>   arch/arm/boot/dts/exynos5260-pinctrl.dtsi |  574 +++++++++++++++++++++++++++++
>   arch/arm/boot/dts/exynos5260.dtsi         |  304 +++++++++++++++
>   2 files changed, 878 insertions(+)
>   create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi
>   create mode 100644 arch/arm/boot/dts/exynos5260.dtsi

Reviewed-by: Tomasz Figa <t.figa@samsung.com>

Best regards,
Tomasz

Re: [PATCH v3 3/3] ARM: dts: add dts files for xyref5260 board

[Rahul Sharma]

Thanks Tomasz,

On 15 February 2014 00:27, Tomasz Figa <tomasz.figa@gmail.com> wrote:
> Hi Rahul,
>
> The patch looks good, except one issue pointed inline.
>
>
> On 14.02.2014 14:37, Rahul Sharma wrote:
>>
>> diff --git a/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
>> b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
>> new file mode 100644
>> index 0000000..c4efc1e
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
>
>
> [snip]
>
>
>> +&mmc_0 {
>> +       status = "okay";
>> +       num-slots = <1>;
>> +       broken-cd;
>> +       bypass-smu;
>> +       supports-highspeed;
>> +       supports-hs200-mode; /* 200 Mhz */
>> +       fifo-depth = <0x40>;
>
>
> This is a SoC-level property and it is already specified in your
> exynos5260.dtsi.
>

Tomasz,

yea correct. I will put these inside SoC node.

Regards,
Rahul Sharma.

>
>> +       card-detect-delay = <200>;
>> +       samsung,dw-mshc-ciu-div = <3>;
>> +       samsung,dw-mshc-sdr-timing = <0 4>;
>> +       samsung,dw-mshc-ddr-timing = <0 2>;
>> +       pinctrl-names = "default";
>> +       pinctrl-0 = <&sd0_rdqs &sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4
>> &sd0_bus8>;
>> +
>> +       slot@0 {
>> +               reg = <0>;
>> +               bus-width = <8>;
>> +       };
>> +};
>> +
>> +&mmc_2 {
>> +       status = "okay";
>> +       num-slots = <1>;
>> +       supports-highspeed;
>> +       fifo-depth = <0x40>;
>
>
> Ditto.
>
> Best regards,
> Tomasz

[PATCH v3 3/3] ARM: dts: add dts files for xyref5260 board

[Rahul Sharma]

Thanks Tomasz,

On 15 February 2014 00:27, Tomasz Figa <tomasz.figa@gmail.com> wrote:
> Hi Rahul,
>
> The patch looks good, except one issue pointed inline.
>
>
> On 14.02.2014 14:37, Rahul Sharma wrote:
>>
>> diff --git a/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
>> b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
>> new file mode 100644
>> index 0000000..c4efc1e
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/exynos5260-xyref5260-evt0.dts
>
>
> [snip]
>
>
>> +&mmc_0 {
>> +       status = "okay";
>> +       num-slots = <1>;
>> +       broken-cd;
>> +       bypass-smu;
>> +       supports-highspeed;
>> +       supports-hs200-mode; /* 200 Mhz */
>> +       fifo-depth = <0x40>;
>
>
> This is a SoC-level property and it is already specified in your
> exynos5260.dtsi.
>

Tomasz,

yea correct. I will put these inside SoC node.

Regards,
Rahul Sharma.

>
>> +       card-detect-delay = <200>;
>> +       samsung,dw-mshc-ciu-div = <3>;
>> +       samsung,dw-mshc-sdr-timing = <0 4>;
>> +       samsung,dw-mshc-ddr-timing = <0 2>;
>> +       pinctrl-names = "default";
>> +       pinctrl-0 = <&sd0_rdqs &sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4
>> &sd0_bus8>;
>> +
>> +       slot at 0 {
>> +               reg = <0>;
>> +               bus-width = <8>;
>> +       };
>> +};
>> +
>> +&mmc_2 {
>> +       status = "okay";
>> +       num-slots = <1>;
>> +       supports-highspeed;
>> +       fifo-depth = <0x40>;
>
>
> Ditto.
>
> Best regards,
> Tomasz

Re: [PATCH v3 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC

[Sachin Kamat]

Hi Rahul,

On 14 February 2014 19:07, Rahul Sharma <rahul.sharma@samsung.com> wrote:
> From: Pankaj Dubey <pankaj.dubey@samsung.com>
>
> This patch add basic arch side support for exynos5260 SoC.
>
> Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
> Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
> ---
>  arch/arm/mach-exynos/Kconfig             |    9 +++++++++
>  arch/arm/mach-exynos/common.c            |   11 +++++++++++
>  arch/arm/mach-exynos/include/mach/map.h  |    1 +
>  arch/arm/mach-exynos/mach-exynos5-dt.c   |    1 +
>  arch/arm/plat-samsung/include/plat/cpu.h |    8 ++++++++
>  5 files changed, 30 insertions(+)
>
> diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
> index 4c414af..5c96248 100644
> --- a/arch/arm/mach-exynos/Kconfig
> +++ b/arch/arm/mach-exynos/Kconfig
> @@ -91,6 +91,15 @@ config SOC_EXYNOS5250
>         help
>           Enable EXYNOS5250 SoC support
>
> +config SOC_EXYNOS5260
> +       bool "SAMSUNG EXYNOS5260"
> +       default y
> +       depends on ARCH_EXYNOS5
> +       select AUTO_ZRELADDR
> +       select SAMSUNG_DMADEV
> +       help
> +         Enable EXYNOS5260 SoC support
> +

Per SoC entries are no longer needed with the patch at [1].

[1] http://www.spinics.net/lists/linux-samsung-soc/msg26253.html

-- 
With warm regards,
Sachin

[PATCH v3 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC

[Sachin Kamat]

Hi Rahul,

On 14 February 2014 19:07, Rahul Sharma <rahul.sharma@samsung.com> wrote:
> From: Pankaj Dubey <pankaj.dubey@samsung.com>
>
> This patch add basic arch side support for exynos5260 SoC.
>
> Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
> Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
> ---
>  arch/arm/mach-exynos/Kconfig             |    9 +++++++++
>  arch/arm/mach-exynos/common.c            |   11 +++++++++++
>  arch/arm/mach-exynos/include/mach/map.h  |    1 +
>  arch/arm/mach-exynos/mach-exynos5-dt.c   |    1 +
>  arch/arm/plat-samsung/include/plat/cpu.h |    8 ++++++++
>  5 files changed, 30 insertions(+)
>
> diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
> index 4c414af..5c96248 100644
> --- a/arch/arm/mach-exynos/Kconfig
> +++ b/arch/arm/mach-exynos/Kconfig
> @@ -91,6 +91,15 @@ config SOC_EXYNOS5250
>         help
>           Enable EXYNOS5250 SoC support
>
> +config SOC_EXYNOS5260
> +       bool "SAMSUNG EXYNOS5260"
> +       default y
> +       depends on ARCH_EXYNOS5
> +       select AUTO_ZRELADDR
> +       select SAMSUNG_DMADEV
> +       help
> +         Enable EXYNOS5260 SoC support
> +

Per SoC entries are no longer needed with the patch at [1].

[1] http://www.spinics.net/lists/linux-samsung-soc/msg26253.html

-- 
With warm regards,
Sachin