* [U-Boot] [PATCH v2] configs: sama5d3xek: add default config for CMP board
@ 2017-03-24 1:26 Wenyou Yang
2017-04-22 3:07 ` sjg at google.com
0 siblings, 1 reply; 2+ messages in thread
From: Wenyou Yang @ 2017-03-24 1:26 UTC (permalink / raw)
To: u-boot
The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865, and
some power rails. The board is mainly used to measure the power
consumption. As all those changes are done in at91bootstrap,
in U-Boot, only use another device tree file, no code needed
to change.
As there is additional power consumption when enbling the USB
Host and USB device, for the power consumption measurement
intention, disable the USB host and device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
---
The patch is based on
[PATCH v4 0/6] board: sama5d3: convert boards to support DM/DT
https://lists.denx.de/pipermail/u-boot/2017-March/284732.html
Changes in v2:
- Remove the SPL config options.
- Convert MACB to support driver model.
- Use CONFIG_DEBUG_UART_CLOCK as the input clock for the early debug UART.
configs/sama5d36ek_cmp_mmc_defconfig | 51 ++++++++++++++++++++++++++++++
configs/sama5d36ek_cmp_nandflash_defconfig | 51 ++++++++++++++++++++++++++++++
configs/sama5d36ek_cmp_spiflash_defconfig | 51 ++++++++++++++++++++++++++++++
3 files changed, 153 insertions(+)
create mode 100644 configs/sama5d36ek_cmp_mmc_defconfig
create mode 100644 configs/sama5d36ek_cmp_nandflash_defconfig
create mode 100644 configs/sama5d36ek_cmp_spiflash_defconfig
diff --git a/configs/sama5d36ek_cmp_mmc_defconfig b/configs/sama5d36ek_cmp_mmc_defconfig
new file mode 100644
index 0000000000..32a21f9294
--- /dev/null
+++ b/configs/sama5d36ek_cmp_mmc_defconfig
@@ -0,0 +1,51 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D3XEK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp"
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D3,SYS_USE_MMC"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_LCD=y
diff --git a/configs/sama5d36ek_cmp_nandflash_defconfig b/configs/sama5d36ek_cmp_nandflash_defconfig
new file mode 100644
index 0000000000..34c4de17b9
--- /dev/null
+++ b/configs/sama5d36ek_cmp_nandflash_defconfig
@@ -0,0 +1,51 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D3XEK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp"
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D3,SYS_USE_NANDFLASH"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_LCD=y
diff --git a/configs/sama5d36ek_cmp_spiflash_defconfig b/configs/sama5d36ek_cmp_spiflash_defconfig
new file mode 100644
index 0000000000..42c31111a1
--- /dev/null
+++ b/configs/sama5d36ek_cmp_spiflash_defconfig
@@ -0,0 +1,51 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D3XEK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp"
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D3,SYS_USE_SERIALFLASH"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_LCD=y
--
2.11.0
^ permalink raw reply related [flat|nested] 2+ messages in thread
* [U-Boot] [PATCH v2] configs: sama5d3xek: add default config for CMP board
2017-03-24 1:26 [U-Boot] [PATCH v2] configs: sama5d3xek: add default config for CMP board Wenyou Yang
@ 2017-04-22 3:07 ` sjg at google.com
0 siblings, 0 replies; 2+ messages in thread
From: sjg at google.com @ 2017-04-22 3:07 UTC (permalink / raw)
To: u-boot
The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865, and
some power rails. The board is mainly used to measure the power
consumption. As all those changes are done in at91bootstrap,
in U-Boot, only use another device tree file, no code needed
to change.
As there is additional power consumption when enbling the USB
Host and USB device, for the power consumption measurement
intention, disable the USB host and device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
---
The patch is based on
[PATCH v4 0/6] board: sama5d3: convert boards to support DM/DT
https://lists.denx.de/pipermail/u-boot/2017-March/284732.html
Changes in v2:
- Remove the SPL config options.
- Convert MACB to support driver model.
- Use CONFIG_DEBUG_UART_CLOCK as the input clock for the early debug UART.
configs/sama5d36ek_cmp_mmc_defconfig | 51 ++++++++++++++++++++++++++++++
configs/sama5d36ek_cmp_nandflash_defconfig | 51 ++++++++++++++++++++++++++++++
configs/sama5d36ek_cmp_spiflash_defconfig | 51 ++++++++++++++++++++++++++++++
3 files changed, 153 insertions(+)
create mode 100644 configs/sama5d36ek_cmp_mmc_defconfig
create mode 100644 configs/sama5d36ek_cmp_nandflash_defconfig
create mode 100644 configs/sama5d36ek_cmp_spiflash_defconfig
Applied to u-boot-dm/next, thanks!
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2017-04-22 3:07 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-03-24 1:26 [U-Boot] [PATCH v2] configs: sama5d3xek: add default config for CMP board Wenyou Yang
2017-04-22 3:07 ` sjg at google.com
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.