* [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs
@ 2015-01-01 23:17 Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 01/22] x86: Correct XIP_ROM_SIZE Simon Glass
` (21 more replies)
0 siblings, 22 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:17 UTC (permalink / raw)
To: u-boot
One of the four items left to fix up for bare ivybridge support in U-Boot
is MTRRs. These are an important part of the x86 platform since they provide
a means to control the cache behaviour for areas of memory.
Memory areas can be marked as uncacheable or cacheable. For cacheable the
write behaviour can be controlled:
- write-back: data is not written back from the cache until evicted
- write-though: data goes into the cache but is also written to memory
- write-protect: data cannot be written to this area
- write-combining: multiple writes to this area can be combined
This series adds support for deciding the MTRR setup that should be used,
commiting it to registers before relocation, updating it for the video frame
buffer, disabling CAR (cache-as-RAM) when needed and making sure that the
faster possible execution speed is provided. In addition an 'mtrr' command
is added to permit inspection and adjustment of MTRR registers from the
command line.
Changes in v2:
- Remove CONFIG_RAMTOP from mtrr.h in this patch
- Use CONFIG_VIDEO directly to control running the video BIOS
- Remove definition of 'ulong start' from this patch
- Remove unused Lhlt code
- Use a simple 'ret' instruction to return
- Use a simple call instruction to call car_uninit
- Use constants for microcode MSRs and header length
- Move cmd_mtrr to arch/x86/lib
- Correct 'platform' typo
Simon Glass (22):
x86: Correct XIP_ROM_SIZE
x86: Drop RAMTOP Kconfig
x86: Correct ifdtool microcode calculation
x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES
x86: config: Always scroll the display by 5 lines, for speed
x86: video: Add a debug() to display the frame buffer address
x86: pci: Don't return a vesa mode when there is not video
x86: video: Add debug option to time the BIOS copy
x86: ivybridge: Only run the Video BIOS when video is enabled
x86: Use cache, don't clear the display in video BIOS
x86: Tidy up VESA mode numbers
x86: pci: Display vesa modes in hex
x86: ivybridge: Drop support for ROM caching
x86: Add support for MTRRs
x86: ivybridge: Set up an MTRR for the video frame buffer
x86: board_f: Adjust x86 boot order for performance
x86: ivybridge: Request MTRRs for DRAM regions
x86: Commit the current MTRRs before relocation
x86: ivybridge: Add a way to turn off the CAR
x86: Disable CAR before relocation on platforms that need it
x86: ivybridge: Update microcode early in boot
x86: Add an 'mtrr' command to list and adjust MTRRs
arch/x86/Kconfig | 6 +-
arch/x86/cpu/Makefile | 1 +
arch/x86/cpu/coreboot/coreboot.c | 22 ++--
arch/x86/cpu/ivybridge/car.S | 74 ++++++++++-
arch/x86/cpu/ivybridge/cpu.c | 27 +---
arch/x86/cpu/ivybridge/gma.c | 16 ++-
arch/x86/cpu/ivybridge/microcode_intel.c | 26 ++--
arch/x86/cpu/ivybridge/sdram.c | 10 ++
arch/x86/cpu/mtrr.c | 81 ++++++++++++
arch/x86/cpu/start.S | 9 ++
arch/x86/dts/link.dts | 3 -
arch/x86/include/asm/arch-ivybridge/microcode.h | 6 +
arch/x86/include/asm/global_data.h | 15 +++
arch/x86/include/asm/mtrr.h | 163 +++++++++++-------------
arch/x86/lib/Makefile | 1 +
arch/x86/lib/bios.c | 14 +-
arch/x86/lib/cmd_mtrr.c | 138 ++++++++++++++++++++
arch/x86/lib/init_helpers.c | 8 ++
common/board_f.c | 8 +-
doc/README.x86 | 18 ++-
drivers/pci/pci_rom.c | 9 +-
drivers/video/cfb_console.c | 26 ++--
drivers/video/x86_fb.c | 1 +
include/configs/x86-common.h | 1 +
tools/ifdtool.c | 4 +-
25 files changed, 511 insertions(+), 176 deletions(-)
create mode 100644 arch/x86/cpu/mtrr.c
create mode 100644 arch/x86/lib/cmd_mtrr.c
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 01/22] x86: Correct XIP_ROM_SIZE
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
@ 2015-01-01 23:17 ` Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 02/22] x86: Drop RAMTOP Kconfig Simon Glass
` (20 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:17 UTC (permalink / raw)
To: u-boot
This should default to the size of the ROM for faster execution before
relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
arch/x86/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index ebf72b3..7d007bb 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -53,7 +53,7 @@ config RAMTOP
config XIP_ROM_SIZE
hex
- default 0x10000
+ default ROM_SIZE
config CPU_ADDR_BITS
int
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 02/22] x86: Drop RAMTOP Kconfig
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 01/22] x86: Correct XIP_ROM_SIZE Simon Glass
@ 2015-01-01 23:17 ` Simon Glass
2015-01-04 2:26 ` Bin Meng
2015-01-01 23:17 ` [U-Boot] [PATCH v2 03/22] x86: Correct ifdtool microcode calculation Simon Glass
` (19 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:17 UTC (permalink / raw)
To: u-boot
We don't need this in U-Boot since we calculate it based on available memory.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2:
- Remove CONFIG_RAMTOP from mtrr.h in this patch
arch/x86/Kconfig | 4 ----
arch/x86/include/asm/mtrr.h | 8 --------
2 files changed, 12 deletions(-)
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 7d007bb..e992e64 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -47,10 +47,6 @@ config RAMBASE
hex
default 0x100000
-config RAMTOP
- hex
- default 0x200000
-
config XIP_ROM_SIZE
hex
default ROM_SIZE
diff --git a/arch/x86/include/asm/mtrr.h b/arch/x86/include/asm/mtrr.h
index 5f05a48..dcc995d 100644
--- a/arch/x86/include/asm/mtrr.h
+++ b/arch/x86/include/asm/mtrr.h
@@ -100,10 +100,6 @@ static inline long x86_mtrr_rom_cache_var_index(void) { return -1; }
#endif
-#if !defined(CONFIG_RAMTOP)
-# error "CONFIG_RAMTOP not defined"
-#endif
-
#if ((CONFIG_XIP_ROM_SIZE & (CONFIG_XIP_ROM_SIZE - 1)) != 0)
# error "CONFIG_XIP_ROM_SIZE is not a power of 2"
#endif
@@ -114,8 +110,4 @@ static inline long x86_mtrr_rom_cache_var_index(void) { return -1; }
#define CACHE_ROM_BASE (((1 << 20) - (CONFIG_CACHE_ROM_SIZE >> 12)) << 12)
-#if (CONFIG_RAMTOP & (CONFIG_RAMTOP - 1)) != 0
-# error "CONFIG_RAMTOP must be a power of 2"
-#endif
-
#endif
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 03/22] x86: Correct ifdtool microcode calculation
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 01/22] x86: Correct XIP_ROM_SIZE Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 02/22] x86: Drop RAMTOP Kconfig Simon Glass
@ 2015-01-01 23:17 ` Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES Simon Glass
` (18 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:17 UTC (permalink / raw)
To: u-boot
This currently assumes that U-Boot resides at the start of ROM. Update
it to remove this assumption.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
---
Changes in v2: None
tools/ifdtool.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/tools/ifdtool.c b/tools/ifdtool.c
index fe8366b..590ccc9 100644
--- a/tools/ifdtool.c
+++ b/tools/ifdtool.c
@@ -788,9 +788,9 @@ static int write_uboot(char *image, int size, struct input_file *uboot,
fdt_strerror(data_size));
return -ENOENT;
}
- offset = ucode_ptr - uboot->addr;
+ offset = (uint32_t)(ucode_ptr + size);
ptr = (void *)image + offset;
- ptr[0] = uboot->addr + (data - image);
+ ptr[0] = (data - image) - size;
ptr[1] = data_size;
debug("Wrote microcode pointer at %x: addr=%x, size=%x\n",
ucode_ptr, ptr[0], ptr[1]);
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (2 preceding siblings ...)
2015-01-01 23:17 ` [U-Boot] [PATCH v2 03/22] x86: Correct ifdtool microcode calculation Simon Glass
@ 2015-01-01 23:17 ` Simon Glass
2015-01-20 0:33 ` Simon Glass
2015-01-20 7:42 ` Anatolij Gustschin
2015-01-01 23:17 ` [U-Boot] [PATCH v2 05/22] x86: config: Always scroll the display by 5 lines, for speed Simon Glass
` (17 subsequent siblings)
21 siblings, 2 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:17 UTC (permalink / raw)
To: u-boot
Some machines are very slow to scroll their displays. To cope with this,
support the CONFIG_CONSOLE_SCROLL_LINES option. Setting this to 5 allows
the display to operate at an acceptable speed by scrolling 5 lines at
a time.
This same option is available for LCDs so when these systems are unified
this code can be unified also.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
drivers/video/cfb_console.c | 26 +++++++++++++++++---------
1 file changed, 17 insertions(+), 9 deletions(-)
diff --git a/drivers/video/cfb_console.c b/drivers/video/cfb_console.c
index a653bb4..75cdf61 100644
--- a/drivers/video/cfb_console.c
+++ b/drivers/video/cfb_console.c
@@ -312,7 +312,11 @@ void console_cursor(int state);
#define CONSOLE_ROW_SECOND (video_console_address + CONSOLE_ROW_SIZE)
#define CONSOLE_ROW_LAST (video_console_address + CONSOLE_SIZE - CONSOLE_ROW_SIZE)
#define CONSOLE_SIZE (CONSOLE_ROW_SIZE * CONSOLE_ROWS)
-#define CONSOLE_SCROLL_SIZE (CONSOLE_SIZE - CONSOLE_ROW_SIZE)
+
+/* By default we scroll by a single line */
+#ifndef CONFIG_CONSOLE_SCROLL_LINES
+#define CONFIG_CONSOLE_SCROLL_LINES 1
+#endif
/* Macros */
#ifdef VIDEO_FB_LITTLE_ENDIAN
@@ -753,26 +757,33 @@ static void console_clear_line(int line, int begin, int end)
static void console_scrollup(void)
{
+ const int rows = CONFIG_CONSOLE_SCROLL_LINES;
+ int i;
+
/* copy up rows ignoring the first one */
#ifdef VIDEO_HW_BITBLT
video_hw_bitblt(VIDEO_PIXEL_SIZE, /* bytes per pixel */
0, /* source pos x */
video_logo_height +
- VIDEO_FONT_HEIGHT, /* source pos y */
+ VIDEO_FONT_HEIGHT * rows, /* source pos y */
0, /* dest pos x */
video_logo_height, /* dest pos y */
VIDEO_VISIBLE_COLS, /* frame width */
VIDEO_VISIBLE_ROWS
- video_logo_height
- - VIDEO_FONT_HEIGHT /* frame height */
+ - VIDEO_FONT_HEIGHT * rows /* frame height */
);
#else
- memcpyl(CONSOLE_ROW_FIRST, CONSOLE_ROW_SECOND,
- CONSOLE_SCROLL_SIZE >> 2);
+ memcpyl(CONSOLE_ROW_FIRST, CONSOLE_ROW_FIRST + rows * CONSOLE_ROW_SIZE,
+ (CONSOLE_SIZE - CONSOLE_ROW_SIZE * rows) >> 2);
#endif
/* clear the last one */
- console_clear_line(CONSOLE_ROWS - 1, 0, CONSOLE_COLS - 1);
+ for (i = 1; i <= rows; i++)
+ console_clear_line(CONSOLE_ROWS - i, 0, CONSOLE_COLS - 1);
+
+ /* Decrement row number */
+ console_row -= rows;
}
static void console_back(void)
@@ -884,9 +895,6 @@ static void console_newline(int n)
if (console_row >= CONSOLE_ROWS) {
/* Scroll everything up */
console_scrollup();
-
- /* Decrement row number */
- console_row = CONSOLE_ROWS - 1;
}
}
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 05/22] x86: config: Always scroll the display by 5 lines, for speed
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (3 preceding siblings ...)
2015-01-01 23:17 ` [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES Simon Glass
@ 2015-01-01 23:17 ` Simon Glass
2015-01-23 23:55 ` Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 06/22] x86: video: Add a debug() to display the frame buffer address Simon Glass
` (16 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:17 UTC (permalink / raw)
To: u-boot
Scrolling a line at a time is very slow for reasons that I don't understand.
It seems to take about 100ms to copy 4MB of RAM in the frame buffer. To cope
with this, scroll 5 lines each time.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
include/configs/x86-common.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/include/configs/x86-common.h b/include/configs/x86-common.h
index f16ae32..4f0a3c5 100644
--- a/include/configs/x86-common.h
+++ b/include/configs/x86-common.h
@@ -179,6 +179,7 @@
#define VIDEO_FB_16BPP_WORD_SWAP
#define CONFIG_I8042_KBD
#define CONFIG_CFB_CONSOLE
+#define CONFIG_CONSOLE_SCROLL_LINES 5
/*-----------------------------------------------------------------------
* CPU Features
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 06/22] x86: video: Add a debug() to display the frame buffer address
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (4 preceding siblings ...)
2015-01-01 23:17 ` [U-Boot] [PATCH v2 05/22] x86: config: Always scroll the display by 5 lines, for speed Simon Glass
@ 2015-01-01 23:17 ` Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 07/22] x86: pci: Don't return a vesa mode when there is not video Simon Glass
` (15 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:17 UTC (permalink / raw)
To: u-boot
Provide a way to display this address when booting.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
drivers/video/x86_fb.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/video/x86_fb.c b/drivers/video/x86_fb.c
index 8743a8c..6641033 100644
--- a/drivers/video/x86_fb.c
+++ b/drivers/video/x86_fb.c
@@ -32,6 +32,7 @@ void *video_hw_init(void)
sprintf(gdev->modeIdent, "%dx%dx%d", gdev->winSizeX, gdev->winSizeY,
bits_per_pixel);
printf("%s\n", gdev->modeIdent);
+ debug("Frame buffer at %x\n", gdev->frameAdrs);
return (void *)gdev;
}
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 07/22] x86: pci: Don't return a vesa mode when there is not video
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (5 preceding siblings ...)
2015-01-01 23:17 ` [U-Boot] [PATCH v2 06/22] x86: video: Add a debug() to display the frame buffer address Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 08/22] x86: video: Add debug option to time the BIOS copy Simon Glass
` (14 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
If the video has not been set up, we should not return a success code. This
can be detected by seeing if any of the variables are non-zero.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
drivers/pci/pci_rom.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/pci/pci_rom.c b/drivers/pci/pci_rom.c
index af6a3ae..9808bb3 100644
--- a/drivers/pci/pci_rom.c
+++ b/drivers/pci/pci_rom.c
@@ -205,7 +205,7 @@ int vbe_get_video_info(struct graphic_device *gdev)
gdev->vprBase = vesa->phys_base_ptr;
gdev->cprBase = vesa->phys_base_ptr;
- return 0;
+ return gdev->winSizeX ? 0 : -ENOSYS;
#else
return -ENOSYS;
#endif
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 08/22] x86: video: Add debug option to time the BIOS copy
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (6 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 07/22] x86: pci: Don't return a vesa mode when there is not video Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 09/22] x86: ivybridge: Only run the Video BIOS when video is enabled Simon Glass
` (13 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
This can be very slow - typically 80ms even on a fast machine since it uses
the SPI flash to read the data. Add an option to display the time taken.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
Changes in v2: None
drivers/pci/pci_rom.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/pci/pci_rom.c b/drivers/pci/pci_rom.c
index 9808bb3..5ba315b 100644
--- a/drivers/pci/pci_rom.c
+++ b/drivers/pci/pci_rom.c
@@ -156,6 +156,8 @@ int pci_rom_load(uint16_t class, struct pci_rom_header *rom_header,
target = (void *)PCI_VGA_RAM_IMAGE_START;
if (target != rom_header) {
+ ulong start = get_timer(0);
+
debug("Copying VGA ROM Image from %p to %p, 0x%x bytes\n",
rom_header, target, rom_size);
memcpy(target, rom_header, rom_size);
@@ -163,6 +165,7 @@ int pci_rom_load(uint16_t class, struct pci_rom_header *rom_header,
printf("VGA ROM copy failed\n");
return -EFAULT;
}
+ debug("Copy took %lums\n", get_timer(start));
}
*ram_headerp = target;
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 09/22] x86: ivybridge: Only run the Video BIOS when video is enabled
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (7 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 08/22] x86: video: Add debug option to time the BIOS copy Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-04 2:31 ` Bin Meng
2015-01-01 23:18 ` [U-Boot] [PATCH v2 10/22] x86: Use cache, don't clear the display in video BIOS Simon Glass
` (12 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
This takes about about 700ms on link when running natively and 900ms when
running using the emulator. It is a waste of time if video is not enabled,
so don't bother running the video BIOS in that case.
We could add a command to run the video BIOS later when needed, but this is
not considered at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2:
- Use CONFIG_VIDEO directly to control running the video BIOS
arch/x86/cpu/ivybridge/gma.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/arch/x86/cpu/ivybridge/gma.c b/arch/x86/cpu/ivybridge/gma.c
index 3d7f740..cf4f87c 100644
--- a/arch/x86/cpu/ivybridge/gma.c
+++ b/arch/x86/cpu/ivybridge/gma.c
@@ -15,6 +15,7 @@
#include <asm/pci.h>
#include <asm/arch/pch.h>
#include <asm/arch/sandybridge.h>
+#include <linux/kconfig.h>
struct gt_powermeter {
u16 reg;
@@ -730,6 +731,9 @@ static int int15_handler(void)
int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
const void *blob, int node)
{
+#ifdef CONFIG_VIDEO
+ ulong start;
+#endif
void *gtt_bar;
u32 reg32;
int ret;
@@ -745,8 +749,11 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
if (ret)
return ret;
+#ifdef CONFIG_VIDEO
+ start = get_timer(0);
ret = pci_run_vga_bios(dev, int15_handler, false);
-
+ debug("BIOS ran in %lums\n", get_timer(start));
+#endif
/* Post VBIOS init */
ret = gma_pm_init_post_vbios(gtt_bar, blob, node);
if (ret)
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 10/22] x86: Use cache, don't clear the display in video BIOS
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (8 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 09/22] x86: ivybridge: Only run the Video BIOS when video is enabled Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:40 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 11/22] x86: Tidy up VESA mode numbers Simon Glass
` (11 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
There is no need to run with the cache disabled, and there is no point in
clearing the display frame buffer since U-Boot does it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
arch/x86/lib/bios.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
diff --git a/arch/x86/lib/bios.c b/arch/x86/lib/bios.c
index d1f8933..4285348 100644
--- a/arch/x86/lib/bios.c
+++ b/arch/x86/lib/bios.c
@@ -210,8 +210,8 @@ static u8 vbe_set_mode(struct vbe_mode_info *mi)
debug("VBE: Setting VESA mode %#04x\n", mi->video_mode);
/* request linear framebuffer mode */
mi->video_mode |= (1 << 14);
- /* request clearing of framebuffer */
- mi->video_mode &= ~(1 << 15);
+ /* don't clear the framebuffer, we do that later */
+ mi->video_mode |= (1 << 15);
realmode_interrupt(0x10, VESA_SET_MODE, mi->video_mode,
0x0000, 0x0000, 0x0000, 0x0000);
@@ -262,7 +262,6 @@ void bios_run_on_x86(pci_dev_t pcidev, unsigned long addr, int vesa_mode,
/* Make sure the code is placed. */
setup_realmode_code();
- disable_caches();
debug("Calling Option ROM at %lx, pci device %#x...", addr, num_dev);
/* Option ROM entry point is at OPROM start + 3 */
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 11/22] x86: Tidy up VESA mode numbers
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (9 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 10/22] x86: Use cache, don't clear the display in video BIOS Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:40 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 12/22] x86: pci: Display vesa modes in hex Simon Glass
` (10 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
There are some bits which should be ignored when displaying the mode number.
Make sure that they are not included in the mode that is displayed.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
arch/x86/lib/bios.c | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/arch/x86/lib/bios.c b/arch/x86/lib/bios.c
index 4285348..1d75cfc 100644
--- a/arch/x86/lib/bios.c
+++ b/arch/x86/lib/bios.c
@@ -207,12 +207,14 @@ static u8 vbe_get_mode_info(struct vbe_mode_info *mi)
static u8 vbe_set_mode(struct vbe_mode_info *mi)
{
- debug("VBE: Setting VESA mode %#04x\n", mi->video_mode);
+ int video_mode = mi->video_mode;
+
+ debug("VBE: Setting VESA mode %#04x\n", video_mode);
/* request linear framebuffer mode */
- mi->video_mode |= (1 << 14);
+ video_mode |= (1 << 14);
/* don't clear the framebuffer, we do that later */
- mi->video_mode |= (1 << 15);
- realmode_interrupt(0x10, VESA_SET_MODE, mi->video_mode,
+ video_mode |= (1 << 15);
+ realmode_interrupt(0x10, VESA_SET_MODE, video_mode,
0x0000, 0x0000, 0x0000, 0x0000);
return 0;
@@ -236,6 +238,7 @@ static void vbe_set_graphics(int vesa_mode, struct vbe_mode_info *mode_info)
return;
}
+ mode_info->video_mode &= 0x3ff;
vbe_set_mode(mode_info);
}
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 12/22] x86: pci: Display vesa modes in hex
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (10 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 11/22] x86: Tidy up VESA mode numbers Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:40 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 13/22] x86: ivybridge: Drop support for ROM caching Simon Glass
` (9 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
The hex value is more commonly understood, so use that instead of decimal.
Add a 0x prefix to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
Changes in v2: None
drivers/pci/pci_rom.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/pci/pci_rom.c b/drivers/pci/pci_rom.c
index 5ba315b..7d25cc9 100644
--- a/drivers/pci/pci_rom.c
+++ b/drivers/pci/pci_rom.c
@@ -247,7 +247,7 @@ int pci_run_vga_bios(pci_dev_t dev, int (*int15_handler)(void), bool emulate)
defined(CONFIG_FRAMEBUFFER_VESA_MODE)
vesa_mode = CONFIG_FRAMEBUFFER_VESA_MODE;
#endif
- debug("Selected vesa mode %d\b", vesa_mode);
+ debug("Selected vesa mode %#x\n", vesa_mode);
if (emulate) {
#ifdef CONFIG_BIOSEMU
BE_VGAInfo *info;
@@ -275,7 +275,7 @@ int pci_run_vga_bios(pci_dev_t dev, int (*int15_handler)(void), bool emulate)
return -ENOSYS;
#endif
}
- debug("Final vesa mode %d\n", mode_info.video_mode);
+ debug("Final vesa mode %#x\n", mode_info.video_mode);
return 0;
}
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 13/22] x86: ivybridge: Drop support for ROM caching
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (11 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 12/22] x86: pci: Display vesa modes in hex Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:40 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 14/22] x86: Add support for MTRRs Simon Glass
` (8 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
This is set up along with CAR (Cache-as-RAM) anyway. When we relocate we
don't really need ROM caching (we read the VGA BIOS from ROM but that is
about it)
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
arch/x86/cpu/ivybridge/cpu.c | 25 -------------------------
1 file changed, 25 deletions(-)
diff --git a/arch/x86/cpu/ivybridge/cpu.c b/arch/x86/cpu/ivybridge/cpu.c
index 969b07b..0543e06 100644
--- a/arch/x86/cpu/ivybridge/cpu.c
+++ b/arch/x86/cpu/ivybridge/cpu.c
@@ -49,27 +49,6 @@ static void enable_spi_prefetch(struct pci_controller *hose, pci_dev_t dev)
pci_hose_write_config_byte(hose, dev, 0xdc, reg8);
}
-static void set_var_mtrr(
- unsigned reg, unsigned base, unsigned size, unsigned type)
-
-{
- /* Bit Bit 32-35 of MTRRphysMask should be set to 1 */
- /* FIXME: It only support 4G less range */
- wrmsr(MTRRphysBase_MSR(reg), base | type, 0);
- wrmsr(MTRRphysMask_MSR(reg), ~(size - 1) | MTRRphysMaskValid,
- (1 << (CONFIG_CPU_ADDR_BITS - 32)) - 1);
-}
-
-static void enable_rom_caching(void)
-{
- disable_caches();
- set_var_mtrr(1, 0xffc00000, 4 << 20, MTRR_TYPE_WRPROT);
- enable_caches();
-
- /* Enable Variable MTRRs */
- wrmsr(MTRRdefType_MSR, 0x800, 0);
-}
-
static int set_flex_ratio_to_tdp_nominal(void)
{
msr_t flex_ratio, msr;
@@ -165,10 +144,6 @@ int arch_cpu_init(void)
/* This is already done in start.S, but let's do it in C */
enable_port80_on_lpc(hose, PCH_LPC_DEV);
- /* already done in car.S */
- if (false)
- enable_rom_caching();
-
set_spi_speed();
/*
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 14/22] x86: Add support for MTRRs
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (12 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 13/22] x86: ivybridge: Drop support for ROM caching Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 15/22] x86: ivybridge: Set up an MTRR for the video frame buffer Simon Glass
` (7 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
Memory Type Range Registers are used to tell the CPU whether memory is
cacheable and if so the cache write mode to use.
Clean up the existing header file to follow style, and remove the unneeded
code.
These can speed up booting so should be supported. Add these to global_data
so they can be requested while booting. We will apply the changes during
relocation (in a later commit).
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
arch/x86/cpu/Makefile | 1 +
arch/x86/cpu/coreboot/coreboot.c | 22 +++---
arch/x86/cpu/ivybridge/car.S | 12 +--
arch/x86/cpu/mtrr.c | 81 +++++++++++++++++++
arch/x86/include/asm/global_data.h | 15 ++++
arch/x86/include/asm/mtrr.h | 157 +++++++++++++++++--------------------
6 files changed, 187 insertions(+), 101 deletions(-)
create mode 100644 arch/x86/cpu/mtrr.c
diff --git a/arch/x86/cpu/Makefile b/arch/x86/cpu/Makefile
index 5033d2b..62e43c0 100644
--- a/arch/x86/cpu/Makefile
+++ b/arch/x86/cpu/Makefile
@@ -17,5 +17,6 @@ obj-$(CONFIG_NORTHBRIDGE_INTEL_SANDYBRIDGE) += ivybridge/
obj-$(CONFIG_NORTHBRIDGE_INTEL_IVYBRIDGE) += ivybridge/
obj-$(CONFIG_INTEL_QUEENSBAY) += queensbay/
obj-y += lapic.o
+obj-y += mtrr.o
obj-$(CONFIG_PCI) += pci.o
obj-y += turbo.o
diff --git a/arch/x86/cpu/coreboot/coreboot.c b/arch/x86/cpu/coreboot/coreboot.c
index cfacc05..6d06d5a 100644
--- a/arch/x86/cpu/coreboot/coreboot.c
+++ b/arch/x86/cpu/coreboot/coreboot.c
@@ -15,6 +15,7 @@
#include <asm/cache.h>
#include <asm/cpu.h>
#include <asm/io.h>
+#include <asm/mtrr.h>
#include <asm/arch/tables.h>
#include <asm/arch/sysinfo.h>
#include <asm/arch/timestamp.h>
@@ -64,11 +65,6 @@ int board_eth_init(bd_t *bis)
return pci_eth_init(bis);
}
-#define MTRR_TYPE_WP 5
-#define MTRRcap_MSR 0xfe
-#define MTRRphysBase_MSR(reg) (0x200 + 2 * (reg))
-#define MTRRphysMask_MSR(reg) (0x200 + 2 * (reg) + 1)
-
void board_final_cleanup(void)
{
/* Un-cache the ROM so the kernel has one
@@ -77,15 +73,17 @@ void board_final_cleanup(void)
* Coreboot should have assigned this to the
* top available variable MTRR.
*/
- u8 top_mtrr = (native_read_msr(MTRRcap_MSR) & 0xff) - 1;
- u8 top_type = native_read_msr(MTRRphysBase_MSR(top_mtrr)) & 0xff;
+ u8 top_mtrr = (native_read_msr(MTRR_CAP_MSR) & 0xff) - 1;
+ u8 top_type = native_read_msr(MTRR_PHYS_BASE_MSR(top_mtrr)) & 0xff;
/* Make sure this MTRR is the correct Write-Protected type */
- if (top_type == MTRR_TYPE_WP) {
- disable_caches();
- wrmsrl(MTRRphysBase_MSR(top_mtrr), 0);
- wrmsrl(MTRRphysMask_MSR(top_mtrr), 0);
- enable_caches();
+ if (top_type == MTRR_TYPE_WRPROT) {
+ struct mtrr_state state;
+
+ mtrr_open(&state);
+ wrmsrl(MTRR_PHYS_BASE_MSR(top_mtrr), 0);
+ wrmsrl(MTRR_PHYS_MASK_MSR(top_mtrr), 0);
+ mtrr_close(&state);
}
/* Issue SMI to Coreboot to lock down ME and registers */
diff --git a/arch/x86/cpu/ivybridge/car.S b/arch/x86/cpu/ivybridge/car.S
index dca68e4..72b22ea 100644
--- a/arch/x86/cpu/ivybridge/car.S
+++ b/arch/x86/cpu/ivybridge/car.S
@@ -61,7 +61,7 @@ clear_mtrrs:
post_code(POST_CAR_MTRR)
/* Configure the default memory type to uncacheable */
- movl $MTRRdefType_MSR, %ecx
+ movl $MTRR_DEF_TYPE_MSR, %ecx
rdmsr
andl $(~0x00000cff), %eax
wrmsr
@@ -76,16 +76,16 @@ clear_mtrrs:
post_code(POST_CAR_BASE_ADDRESS)
/* Set Cache-as-RAM mask */
movl $(MTRR_PHYS_MASK_MSR(0)), %ecx
- movl $(~(CACHE_AS_RAM_SIZE - 1) | MTRRphysMaskValid), %eax
+ movl $(~(CACHE_AS_RAM_SIZE - 1) | MTRR_PHYS_MASK_VALID), %eax
movl $CPU_PHYSMASK_HI, %edx
wrmsr
post_code(POST_CAR_MASK)
/* Enable MTRR */
- movl $MTRRdefType_MSR, %ecx
+ movl $MTRR_DEF_TYPE_MSR, %ecx
rdmsr
- orl $MTRRdefTypeEn, %eax
+ orl $MTRR_DEF_TYPE_EN, %eax
wrmsr
/* Enable cache (CR0.CD = 0, CR0.NW = 0) */
@@ -130,7 +130,7 @@ clear_mtrrs:
movl $MTRR_PHYS_MASK_MSR(1), %ecx
movl $CPU_PHYSMASK_HI, %edx
- movl $(~(CONFIG_XIP_ROM_SIZE - 1) | MTRRphysMaskValid), %eax
+ movl $(~(CONFIG_XIP_ROM_SIZE - 1) | MTRR_PHYS_MASK_VALID), %eax
wrmsr
post_code(POST_CAR_ROM_CACHE)
@@ -141,7 +141,7 @@ clear_mtrrs:
xorl %edx, %edx
wrmsr
movl $MTRR_PHYS_MASK_MSR(2), %ecx
- movl $(CACHE_MRC_MASK | MTRRphysMaskValid), %eax
+ movl $(CACHE_MRC_MASK | MTRR_PHYS_MASK_VALID), %eax
movl $CPU_PHYSMASK_HI, %edx
wrmsr
#endif
diff --git a/arch/x86/cpu/mtrr.c b/arch/x86/cpu/mtrr.c
new file mode 100644
index 0000000..d5a825d1
--- /dev/null
+++ b/arch/x86/cpu/mtrr.c
@@ -0,0 +1,81 @@
+/*
+ * (C) Copyright 2014 Google, Inc
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Memory Type Range Regsters - these are used to tell the CPU whether
+ * memory is cacheable and if so the cache write mode to use.
+ *
+ * These can speed up booting. See the mtrr command.
+ *
+ * Reference: Intel Architecture Software Developer's Manual, Volume 3:
+ * System Programming
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/msr.h>
+#include <asm/mtrr.h>
+
+/* Prepare to adjust MTRRs */
+void mtrr_open(struct mtrr_state *state)
+{
+ state->enable_cache = dcache_status();
+
+ if (state->enable_cache)
+ disable_caches();
+ state->deftype = native_read_msr(MTRR_DEF_TYPE_MSR);
+ wrmsrl(MTRR_DEF_TYPE_MSR, state->deftype & ~MTRR_DEF_TYPE_EN);
+}
+
+/* Clean up after adjusting MTRRs, and enable them */
+void mtrr_close(struct mtrr_state *state)
+{
+ wrmsrl(MTRR_DEF_TYPE_MSR, state->deftype | MTRR_DEF_TYPE_EN);
+ if (state->enable_cache)
+ enable_caches();
+}
+
+int mtrr_commit(bool do_caches)
+{
+ struct mtrr_request *req = gd->arch.mtrr_req;
+ struct mtrr_state state;
+ uint64_t mask;
+ int i;
+
+ mtrr_open(&state);
+ for (i = 0; i < gd->arch.mtrr_req_count; i++, req++) {
+ mask = ~(req->size - 1);
+ mask &= (1ULL << CONFIG_CPU_ADDR_BITS) - 1;
+ wrmsrl(MTRR_PHYS_BASE_MSR(i), req->start | req->type);
+ wrmsrl(MTRR_PHYS_MASK_MSR(i), mask | MTRR_PHYS_MASK_VALID);
+ }
+
+ /* Clear the ones that are unused */
+ for (; i < MTRR_COUNT; i++)
+ wrmsrl(MTRR_PHYS_MASK_MSR(i), 0);
+ mtrr_close(&state);
+
+ return 0;
+}
+
+int mtrr_add_request(int type, uint64_t start, uint64_t size)
+{
+ struct mtrr_request *req;
+ uint64_t mask;
+
+ if (gd->arch.mtrr_req_count == MAX_MTRR_REQUESTS)
+ return -ENOSPC;
+ req = &gd->arch.mtrr_req[gd->arch.mtrr_req_count++];
+ req->type = type;
+ req->start = start;
+ req->size = size;
+ debug("%d: type=%d, %08llx %08llx\n", gd->arch.mtrr_req_count - 1,
+ req->type, req->start, req->size);
+ mask = ~(req->size - 1);
+ mask &= (1ULL << CONFIG_CPU_ADDR_BITS) - 1;
+ mask |= MTRR_PHYS_MASK_VALID;
+ debug(" %016llx %016llx\n", req->start | req->type, mask);
+
+ return 0;
+}
diff --git a/arch/x86/include/asm/global_data.h b/arch/x86/include/asm/global_data.h
index 03d491a..15e76f6 100644
--- a/arch/x86/include/asm/global_data.h
+++ b/arch/x86/include/asm/global_data.h
@@ -29,6 +29,19 @@ struct memory_info {
struct memory_area area[CONFIG_NR_DRAM_BANKS];
};
+#define MAX_MTRR_REQUESTS 8
+
+/**
+ * A request for a memory region to be set up in a particular way. These
+ * requests are processed before board_init_r() is called. They are generally
+ * optional and can be ignored with some performance impact.
+ */
+struct mtrr_request {
+ int type; /* MTRR_TYPE_... */
+ uint64_t start;
+ uint64_t size;
+};
+
/* Architecture-specific global data */
struct arch_global_data {
struct global_data *gd_addr; /* Location of Global Data */
@@ -50,6 +63,8 @@ struct arch_global_data {
#ifdef CONFIG_HAVE_FSP
void *hob_list; /* FSP HOB list */
#endif
+ struct mtrr_request mtrr_req[MAX_MTRR_REQUESTS];
+ int mtrr_req_count;
};
#endif
diff --git a/arch/x86/include/asm/mtrr.h b/arch/x86/include/asm/mtrr.h
index dcc995d..3c11740 100644
--- a/arch/x86/include/asm/mtrr.h
+++ b/arch/x86/include/asm/mtrr.h
@@ -9,94 +9,85 @@
#ifndef _ASM_MTRR_H
#define _ASM_MTRR_H
-/* These are the region types */
-#define MTRR_TYPE_UNCACHEABLE 0
-#define MTRR_TYPE_WRCOMB 1
-/*#define MTRR_TYPE_ 2*/
-/*#define MTRR_TYPE_ 3*/
-#define MTRR_TYPE_WRTHROUGH 4
-#define MTRR_TYPE_WRPROT 5
-#define MTRR_TYPE_WRBACK 6
-#define MTRR_NUM_TYPES 7
-
-#define MTRRcap_MSR 0x0fe
-#define MTRRdefType_MSR 0x2ff
-
-#define MTRRdefTypeEn (1 << 11)
-#define MTRRdefTypeFixEn (1 << 10)
-
-#define SMRRphysBase_MSR 0x1f2
-#define SMRRphysMask_MSR 0x1f3
-
-#define MTRRphysBase_MSR(reg) (0x200 + 2 * (reg))
-#define MTRRphysMask_MSR(reg) (0x200 + 2 * (reg) + 1)
-
-#define MTRRphysMaskValid (1 << 11)
-
-#define NUM_FIXED_RANGES 88
-#define RANGES_PER_FIXED_MTRR 8
-#define MTRRfix64K_00000_MSR 0x250
-#define MTRRfix16K_80000_MSR 0x258
-#define MTRRfix16K_A0000_MSR 0x259
-#define MTRRfix4K_C0000_MSR 0x268
-#define MTRRfix4K_C8000_MSR 0x269
-#define MTRRfix4K_D0000_MSR 0x26a
-#define MTRRfix4K_D8000_MSR 0x26b
-#define MTRRfix4K_E0000_MSR 0x26c
-#define MTRRfix4K_E8000_MSR 0x26d
-#define MTRRfix4K_F0000_MSR 0x26e
-#define MTRRfix4K_F8000_MSR 0x26f
+/* MTRR region types */
+#define MTRR_TYPE_UNCACHEABLE 0
+#define MTRR_TYPE_WRCOMB 1
+#define MTRR_TYPE_WRTHROUGH 4
+#define MTRR_TYPE_WRPROT 5
+#define MTRR_TYPE_WRBACK 6
+
+#define MTRR_TYPE_COUNT 7
+
+#define MTRR_CAP_MSR 0x0fe
+#define MTRR_DEF_TYPE_MSR 0x2ff
+
+#define MTRR_DEF_TYPE_EN (1 << 11)
+#define MTRR_DEF_TYPE_FIX_EN (1 << 10)
+
+#define MTRR_PHYS_BASE_MSR(reg) (0x200 + 2 * (reg))
+#define MTRR_PHYS_MASK_MSR(reg) (0x200 + 2 * (reg) + 1)
+
+#define MTRR_PHYS_MASK_VALID (1 << 11)
+
+#define MTRR_BASE_TYPE_MASK 0x7
+
+/* Number of MTRRs supported */
+#define MTRR_COUNT 8
#if !defined(__ASSEMBLER__)
-/*
- * The MTRR code has some side effects that the callers should be aware for.
- * 1. The call sequence matters. x86_setup_mtrrs() calls
- * x86_setup_fixed_mtrrs_no_enable() then enable_fixed_mtrrs() (equivalent
- * of x86_setup_fixed_mtrrs()) then x86_setup_var_mtrrs(). If the callers
- * want to call the components of x86_setup_mtrrs() because of other
- * rquirements the ordering should still preserved.
- * 2. enable_fixed_mtrr() will enable both variable and fixed MTRRs because
- * of the nature of the global MTRR enable flag. Therefore, all direct
- * or indirect callers of enable_fixed_mtrr() should ensure that the
- * variable MTRR MSRs do not contain bad ranges.
- * 3. If CONFIG_CACHE_ROM is selected an MTRR is allocated for enabling
- * the caching of the ROM. However, it is set to uncacheable (UC). It
- * is the responsiblity of the caller to enable it by calling
- * x86_mtrr_enable_rom_caching().
+/**
+ * Information about the previous MTRR state, set up by mtrr_open()
+ *
+ * @deftype: Previous value of MTRR_DEF_TYPE_MSR
+ * @enable_cache: true if cache was enabled
*/
-void x86_setup_mtrrs(void);
-/*
- * x86_setup_var_mtrrs() parameters:
- * address_bits - number of physical address bits supported by cpu
- * above4gb - 2 means dynamically detect number of variable MTRRs available.
- * non-zero means handle memory ranges above 4GiB.
- * 0 means ignore memory ranges above 4GiB
+struct mtrr_state {
+ uint64_t deftype;
+ bool enable_cache;
+};
+
+/**
+ * mtrr_open() - Prepare to adjust MTRRs
+ *
+ * Use mtrr_open() passing in a structure - this function will init it. Then
+ * when done, pass the same structure to mtrr_close() to re-enable MTRRs and
+ * possibly the cache.
+ *
+ * @state: Empty structure to pass in to hold settings
+ */
+void mtrr_open(struct mtrr_state *state);
+
+/**
+ * mtrr_open() - Clean up after adjusting MTRRs, and enable them
+ *
+ * This uses the structure containing information returned from mtrr_open().
+ *
+ * @state: Structure from mtrr_open()
+ */
+/* */
+void mtrr_close(struct mtrr_state *state);
+
+/**
+ * mtrr_add_request() - Add a new MTRR request
+ *
+ * This adds a request for a memory region to be set up in a particular way.
+ *
+ * @type: Requested type (MTRR_TYPE_)
+ * @start: Start address
+ * @size: Size
+ */
+int mtrr_add_request(int type, uint64_t start, uint64_t size);
+
+/**
+ * mtrr_commit() - set up the MTRR registers based on current requests
+ *
+ * This sets up MTRRs for the available DRAM and the requests received so far.
+ * It must be called with caches disabled.
+ *
+ * @do_caches: true if caches are currently on
*/
-void x86_setup_var_mtrrs(unsigned int address_bits, unsigned int above4gb);
-void enable_fixed_mtrr(void);
-void x86_setup_fixed_mtrrs(void);
-/* Set up fixed MTRRs but do not enable them. */
-void x86_setup_fixed_mtrrs_no_enable(void);
-int x86_mtrr_check(void);
-/* ROM caching can be used after variable MTRRs are set up. Beware that
- * enabling CONFIG_CACHE_ROM will eat through quite a few MTRRs based on
- * one's IO hole size and WRCOMB resources. Be sure to check the console
- * log when enabling CONFIG_CACHE_ROM or adding WRCOMB resources. Beware that
- * on CPUs with core-scoped MTRR registers such as hyperthreaded CPUs the
- * rom caching will be disabled if all threads run the MTRR code. Therefore,
- * one needs to call x86_mtrr_enable_rom_caching() after all threads of the
- * same core have run the MTRR code. */
-#if CONFIG_CACHE_ROM
-void x86_mtrr_enable_rom_caching(void);
-void x86_mtrr_disable_rom_caching(void);
-/* Return the variable range MTRR index of the ROM cache. */
-long x86_mtrr_rom_cache_var_index(void);
-#else
-static inline void x86_mtrr_enable_rom_caching(void) {}
-static inline void x86_mtrr_disable_rom_caching(void) {}
-static inline long x86_mtrr_rom_cache_var_index(void) { return -1; }
-#endif /* CONFIG_CACHE_ROM */
+int mtrr_commit(bool do_caches);
#endif
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 15/22] x86: ivybridge: Set up an MTRR for the video frame buffer
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (13 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 14/22] x86: Add support for MTRRs Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-04 3:18 ` Bin Meng
2015-01-01 23:18 ` [U-Boot] [PATCH v2 16/22] x86: board_f: Adjust x86 boot order for performance Simon Glass
` (6 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
Set the frame buffer to write-combining. This makes it faster, although for
scrolling write-through is even faster for U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2:
- Remove definition of 'ulong start' from this patch
arch/x86/cpu/ivybridge/gma.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/x86/cpu/ivybridge/gma.c b/arch/x86/cpu/ivybridge/gma.c
index cf4f87c..6cf9654 100644
--- a/arch/x86/cpu/ivybridge/gma.c
+++ b/arch/x86/cpu/ivybridge/gma.c
@@ -12,6 +12,7 @@
#include <fdtdec.h>
#include <pci_rom.h>
#include <asm/io.h>
+#include <asm/mtrr.h>
#include <asm/pci.h>
#include <asm/arch/pch.h>
#include <asm/arch/sandybridge.h>
@@ -735,6 +736,7 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
ulong start;
#endif
void *gtt_bar;
+ ulong base;
u32 reg32;
int ret;
@@ -743,6 +745,11 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
reg32 |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO;
pci_write_config32(dev, PCI_COMMAND, reg32);
+ /* Use write-combining for the graphics memory, 256MB */
+ base = pci_read_bar32(hose, dev, 2);
+ mtrr_add_request(MTRR_TYPE_WRCOMB, base, 256 << 20);
+ mtrr_commit(true);
+
gtt_bar = (void *)pci_read_bar32(pci_bus_to_hose(0), dev, 0);
debug("GT bar %p\n", gtt_bar);
ret = gma_pm_init_pre_vbios(gtt_bar);
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 16/22] x86: board_f: Adjust x86 boot order for performance
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (14 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 15/22] x86: ivybridge: Set up an MTRR for the video frame buffer Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 17/22] x86: ivybridge: Request MTRRs for DRAM regions Simon Glass
` (5 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
For bare platforms we turn off ROM-caching before calling board_init_f_r()
It is then very slow to copy U-Boot from ROM to RAM. So adjust the order so
that the copying happens before we turn off ROM-caching.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
common/board_f.c | 8 +++++---
1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/common/board_f.c b/common/board_f.c
index cfd77f8..3a4b32c 100644
--- a/common/board_f.c
+++ b/common/board_f.c
@@ -985,6 +985,11 @@ static init_fnc_t init_sequence_f[] = {
INIT_FUNC_WATCHDOG_RESET
reloc_fdt,
setup_reloc,
+#ifdef CONFIG_X86
+ copy_uboot_to_ram,
+ clear_bss,
+ do_elf_reloc_fixups,
+#endif
#if !defined(CONFIG_ARM) && !defined(CONFIG_SANDBOX)
jump_to_copy,
#endif
@@ -1044,9 +1049,6 @@ void board_init_f(ulong boot_flags)
*/
static init_fnc_t init_sequence_f_r[] = {
init_cache_f_r,
- copy_uboot_to_ram,
- clear_bss,
- do_elf_reloc_fixups,
NULL,
};
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 17/22] x86: ivybridge: Request MTRRs for DRAM regions
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (15 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 16/22] x86: board_f: Adjust x86 boot order for performance Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 18/22] x86: Commit the current MTRRs before relocation Simon Glass
` (4 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
We should use MTRRs to speed up execution. Add a list of MTRR requests which
will dealt with when we relocate and run from RAM.
We set RAM as cacheable (with write-back) and registers as non-cacheable.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
arch/x86/cpu/ivybridge/sdram.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/x86/cpu/ivybridge/sdram.c b/arch/x86/cpu/ivybridge/sdram.c
index b95e781..9504735 100644
--- a/arch/x86/cpu/ivybridge/sdram.c
+++ b/arch/x86/cpu/ivybridge/sdram.c
@@ -17,6 +17,7 @@
#include <asm/processor.h>
#include <asm/gpio.h>
#include <asm/global_data.h>
+#include <asm/mtrr.h>
#include <asm/pci.h>
#include <asm/arch/me.h>
#include <asm/arch/pei_data.h>
@@ -430,6 +431,15 @@ static int sdram_find(pci_dev_t dev)
add_memory_area(info, (2 << 28) + (2 << 20), 4 << 28);
add_memory_area(info, (4 << 28) + (2 << 20), tseg_base);
add_memory_area(info, 1ULL << 32, touud);
+
+ /* Add MTRRs for memory */
+ mtrr_add_request(MTRR_TYPE_WRBACK, 0, 2ULL << 30);
+ mtrr_add_request(MTRR_TYPE_WRBACK, 2ULL << 30, 512 << 20);
+ mtrr_add_request(MTRR_TYPE_WRBACK, 0xaULL << 28, 256 << 20);
+ mtrr_add_request(MTRR_TYPE_UNCACHEABLE, tseg_base, 16 << 20);
+ mtrr_add_request(MTRR_TYPE_UNCACHEABLE, tseg_base + (16 << 20),
+ 32 << 20);
+
/*
* If >= 4GB installed then memory from TOLUD to 4GB
* is remapped above TOM, TOUUD will account for both
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 18/22] x86: Commit the current MTRRs before relocation
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (16 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 17/22] x86: ivybridge: Request MTRRs for DRAM regions Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 19/22] x86: ivybridge: Add a way to turn off the CAR Simon Glass
` (3 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
Once we stop running from ROM we should set up the MTTRs to speed up
execution. This is only needed for platforms that don't have an FSP.
Also in the Coreboot case, the MTRRs are set up for us.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2: None
arch/x86/lib/init_helpers.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/x86/lib/init_helpers.c b/arch/x86/lib/init_helpers.c
index be4eb12..fc211d9 100644
--- a/arch/x86/lib/init_helpers.c
+++ b/arch/x86/lib/init_helpers.c
@@ -7,6 +7,7 @@
#include <common.h>
#include <fdtdec.h>
#include <spi.h>
+#include <asm/mtrr.h>
#include <asm/sections.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -66,6 +67,13 @@ int calculate_relocation_address(void)
int init_cache_f_r(void)
{
+#if defined(CONFIG_X86_RESET_VECTOR) & !defined(CONFIG_HAVE_FSP)
+ int ret;
+
+ ret = mtrr_commit(false);
+ if (ret)
+ return ret;
+#endif
/* Initialise the CPU cache(s) */
return init_cache();
}
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 19/22] x86: ivybridge: Add a way to turn off the CAR
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (17 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 18/22] x86: Commit the current MTRRs before relocation Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 20/22] x86: Disable CAR before relocation on platforms that need it Simon Glass
` (2 subsequent siblings)
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
Cache-as-RAM should be turned off when we relocate since we want to run from
RAM. Add a function to perform this task.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2:
- Remove unused Lhlt code
- Use a simple 'ret' instruction to return
arch/x86/cpu/ivybridge/car.S | 46 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 46 insertions(+)
diff --git a/arch/x86/cpu/ivybridge/car.S b/arch/x86/cpu/ivybridge/car.S
index 72b22ea..d5f1acf 100644
--- a/arch/x86/cpu/ivybridge/car.S
+++ b/arch/x86/cpu/ivybridge/car.S
@@ -163,6 +163,52 @@ wait_for_sipi:
/* return */
jmp car_init_ret
+.globl car_uninit
+car_uninit:
+ /* Disable cache */
+ movl %cr0, %eax
+ orl $X86_CR0_CD, %eax
+ movl %eax, %cr0
+
+ /* Disable MTRRs */
+ movl $MTRR_DEF_TYPE_MSR, %ecx
+ rdmsr
+ andl $(~MTRR_DEF_TYPE_EN), %eax
+ wrmsr
+
+ /* Disable the no-eviction run state */
+ movl NOEVICTMOD_MSR, %ecx
+ rdmsr
+ andl $~2, %eax
+ wrmsr
+
+ invd
+
+ /* Disable the no-eviction mode */
+ rdmsr
+ andl $~1, %eax
+ wrmsr
+
+#ifdef CONFIG_CACHE_MRC_BIN
+ /* Clear the MTRR that was used to cache MRC */
+ xorl %eax, %eax
+ xorl %edx, %edx
+ movl $MTRR_PHYS_BASE_MSR(2), %ecx
+ wrmsr
+ movl $MTRR_PHYS_MASK_MSR(2), %ecx
+ wrmsr
+#endif
+
+ /* Enable MTRRs */
+ movl $MTRR_DEF_TYPE_MSR, %ecx
+ rdmsr
+ orl $MTRR_DEF_TYPE_EN, %eax
+ wrmsr
+
+ invd
+
+ ret
+
mtrr_table:
/* Fixed MTRRs */
.word 0x250, 0x258, 0x259
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 20/22] x86: Disable CAR before relocation on platforms that need it
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (18 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 19/22] x86: ivybridge: Add a way to turn off the CAR Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-04 3:53 ` Bin Meng
2015-01-01 23:18 ` [U-Boot] [PATCH v2 21/22] x86: ivybridge: Update microcode early in boot Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 22/22] x86: Add an 'mtrr' command to list and adjust MTRRs Simon Glass
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
For platforms with CAR we should disable it before relocation. Check if
this function is available and call it if so.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2:
- Use a simple call instruction to call car_uninit
arch/x86/cpu/start.S | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/x86/cpu/start.S b/arch/x86/cpu/start.S
index 125782c..be8a2dc 100644
--- a/arch/x86/cpu/start.S
+++ b/arch/x86/cpu/start.S
@@ -205,6 +205,15 @@ board_init_f_r_trampoline:
/* Setup global descriptor table so gd->xyz works */
call setup_gdt
+ /* Set if we need to disable CAR */
+.weak car_uninit
+ movl $car_uninit, %eax
+ cmpl $0, %eax
+ jz 1f
+
+ /* Pass return address in ebx */
+ call car_uninit
+1:
/* Re-enter U-Boot by calling board_init_f_r */
call board_init_f_r
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 21/22] x86: ivybridge: Update microcode early in boot
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (19 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 20/22] x86: Disable CAR before relocation on platforms that need it Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 22/22] x86: Add an 'mtrr' command to list and adjust MTRRs Simon Glass
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
At present the normal update (which happens much later) does not work. This
seems to have something to do with the 'no eviction' mode in the CAR, or at
least moving the microcode update after that causes it not to work.
For now, do an update early on so that it definitely works. Also refuse to
continue unless the microcode update check (later in boot) is successful.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2:
- Use constants for microcode MSRs and header length
arch/x86/cpu/ivybridge/car.S | 16 +++++++++++++++
arch/x86/cpu/ivybridge/cpu.c | 2 +-
arch/x86/cpu/ivybridge/microcode_intel.c | 26 ++++++++++++++++---------
arch/x86/dts/link.dts | 3 ---
arch/x86/include/asm/arch-ivybridge/microcode.h | 6 ++++++
5 files changed, 40 insertions(+), 13 deletions(-)
diff --git a/arch/x86/cpu/ivybridge/car.S b/arch/x86/cpu/ivybridge/car.S
index d5f1acf..9441666 100644
--- a/arch/x86/cpu/ivybridge/car.S
+++ b/arch/x86/cpu/ivybridge/car.S
@@ -12,9 +12,11 @@
*/
#include <common.h>
+#include <asm/msr-index.h>
#include <asm/mtrr.h>
#include <asm/post.h>
#include <asm/processor-flags.h>
+#include <asm/arch/microcode.h>
#define MTRR_PHYS_BASE_MSR(reg) (0x200 + 2 * (reg))
#define MTRR_PHYS_MASK_MSR(reg) (0x200 + 2 * (reg) + 1)
@@ -45,6 +47,14 @@ car_init:
movl $0xFEE00300, %esi
movl %eax, (%esi)
+ /* TODO: Load microcode later - the 'no eviction' mode breaks this */
+ movl $MSR_IA32_UCODE_WRITE, %ecx
+ xorl %edx, %edx
+ movl $_dt_ucode_base_size, %eax
+ movl (%eax), %eax
+ addl $UCODE_HEADER_LEN, %eax
+ wrmsr
+
post_code(POST_CAR_SIPI)
/* Zero out all fixed range and variable range MTRRs */
movl $mtrr_table, %esi
@@ -222,3 +232,9 @@ mtrr_table:
.word 0x20C, 0x20D, 0x20E, 0x20F
.word 0x210, 0x211, 0x212, 0x213
mtrr_table_end:
+
+ .align 4
+_dt_ucode_base_size:
+ /* These next two fields are filled in by ifdtool */
+ .long 0 /* microcode base */
+ .long 0 /* microcode size */
diff --git a/arch/x86/cpu/ivybridge/cpu.c b/arch/x86/cpu/ivybridge/cpu.c
index 0543e06..e925310 100644
--- a/arch/x86/cpu/ivybridge/cpu.c
+++ b/arch/x86/cpu/ivybridge/cpu.c
@@ -263,7 +263,7 @@ int print_cpuinfo(void)
enable_lapic();
ret = microcode_update_intel();
- if (ret && ret != -ENOENT && ret != -EEXIST)
+ if (ret)
return ret;
/* Enable upper 128bytes of CMOS */
diff --git a/arch/x86/cpu/ivybridge/microcode_intel.c b/arch/x86/cpu/ivybridge/microcode_intel.c
index 0817751..2440a97 100644
--- a/arch/x86/cpu/ivybridge/microcode_intel.c
+++ b/arch/x86/cpu/ivybridge/microcode_intel.c
@@ -13,7 +13,9 @@
#include <libfdt.h>
#include <asm/cpu.h>
#include <asm/msr.h>
+#include <asm/msr-index.h>
#include <asm/processor.h>
+#include <asm/arch/microcode.h>
/**
* struct microcode_update - standard microcode header from Intel
@@ -40,8 +42,8 @@ static int microcode_decode_node(const void *blob, int node,
update->data = fdt_getprop(blob, node, "data", &update->size);
if (!update->data)
return -EINVAL;
- update->data += 48;
- update->size -= 48;
+ update->data += UCODE_HEADER_LEN;
+ update->size -= UCODE_HEADER_LEN;
update->header_version = fdtdec_get_int(blob, node,
"intel,header-version", 0);
@@ -71,15 +73,16 @@ static inline uint32_t microcode_read_rev(void)
asm volatile (
"xorl %%eax, %%eax\n"
"xorl %%edx, %%edx\n"
- "movl $0x8b, %%ecx\n"
+ "movl %2, %%ecx\n"
"wrmsr\n"
"movl $0x01, %%eax\n"
"cpuid\n"
- "movl $0x8b, %%ecx\n"
+ "movl %2, %%ecx\n"
"rdmsr\n"
: /* outputs */
"=a" (low), "=d" (high)
: /* inputs */
+ "i" (MSR_IA32_UCODE_REV)
: /* clobbers */
"ebx", "ecx"
);
@@ -94,9 +97,9 @@ static void microcode_read_cpu(struct microcode_update *cpu)
struct cpuid_result result;
uint32_t low, high;
- wrmsr(0x8b, 0, 0);
+ wrmsr(MSR_IA32_UCODE_REV, 0, 0);
result = cpuid(1);
- rdmsr(0x8b, low, cpu->update_revision);
+ rdmsr(MSR_IA32_UCODE_REV, low, cpu->update_revision);
x86_model = (result.eax >> 4) & 0x0f;
x86_family = (result.eax >> 8) & 0x0f;
cpu->processor_signature = result.eax;
@@ -120,6 +123,7 @@ int microcode_update_intel(void)
int count;
int node;
int ret;
+ int rev;
microcode_read_cpu(&cpu);
node = 0;
@@ -147,12 +151,16 @@ int microcode_update_intel(void)
skipped++;
continue;
}
- ret = microcode_read_rev();
- wrmsr(0x79, (ulong)update.data, 0);
+ wrmsr(MSR_IA32_UCODE_WRITE, (ulong)update.data, 0);
+ rev = microcode_read_rev();
debug("microcode: updated to revision 0x%x date=%04x-%02x-%02x\n",
- microcode_read_rev(), update.date_code & 0xffff,
+ rev, update.date_code & 0xffff,
(update.date_code >> 24) & 0xff,
(update.date_code >> 16) & 0xff);
+ if (update.update_revision != rev) {
+ printf("Microcode update failed\n");
+ return -EFAULT;
+ }
count++;
} while (1);
}
diff --git a/arch/x86/dts/link.dts b/arch/x86/dts/link.dts
index a739080..1ebc334 100644
--- a/arch/x86/dts/link.dts
+++ b/arch/x86/dts/link.dts
@@ -214,9 +214,6 @@
microcode {
update at 0 {
-#include "microcode/m12206a7_00000029.dtsi"
- };
- update at 1 {
#include "microcode/m12306a9_0000001b.dtsi"
};
};
diff --git a/arch/x86/include/asm/arch-ivybridge/microcode.h b/arch/x86/include/asm/arch-ivybridge/microcode.h
index bc9b87c..b868283 100644
--- a/arch/x86/include/asm/arch-ivybridge/microcode.h
+++ b/arch/x86/include/asm/arch-ivybridge/microcode.h
@@ -7,6 +7,11 @@
#ifndef __ASM_ARCH_MICROCODE_H
#define __ASM_ARCH_MICROCODE_H
+/* Length of the public header on Intel microcode blobs */
+#define UCODE_HEADER_LEN 0x30
+
+#ifndef __ASSEMBLY__
+
/**
* microcode_update_intel() - Apply microcode updates
*
@@ -16,5 +21,6 @@
* not updates were found, -EINVAL if an update was invalid
*/
int microcode_update_intel(void);
+#endif /* __ASSEMBLY__ */
#endif
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 22/22] x86: Add an 'mtrr' command to list and adjust MTRRs
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
` (20 preceding siblings ...)
2015-01-01 23:18 ` [U-Boot] [PATCH v2 21/22] x86: ivybridge: Update microcode early in boot Simon Glass
@ 2015-01-01 23:18 ` Simon Glass
2015-01-04 4:13 ` Bin Meng
21 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-01 23:18 UTC (permalink / raw)
To: u-boot
It is useful to be able to see the MTRR setup in U-Boot. Add a command
to list the state of the variable MTRR registers and allow them to be
changed.
Update the documentation to list some of the available commands.
This does not support fixed MTRRs as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v2:
- Move cmd_mtrr to arch/x86/lib
- Correct 'platform' typo
arch/x86/lib/Makefile | 1 +
arch/x86/lib/cmd_mtrr.c | 138 ++++++++++++++++++++++++++++++++++++++++++++++++
doc/README.x86 | 18 ++++++-
3 files changed, 156 insertions(+), 1 deletion(-)
create mode 100644 arch/x86/lib/cmd_mtrr.c
diff --git a/arch/x86/lib/Makefile b/arch/x86/lib/Makefile
index 73262d7..32d7b98 100644
--- a/arch/x86/lib/Makefile
+++ b/arch/x86/lib/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_HAVE_FSP) += cmd_hob.o
obj-y += gcc.o
obj-y += init_helpers.o
obj-y += interrupts.o
+obj-y += cmd_mtrr.o
obj-$(CONFIG_SYS_PCAT_INTERRUPTS) += pcat_interrupts.o
obj-$(CONFIG_SYS_PCAT_TIMER) += pcat_timer.o
obj-$(CONFIG_PCI) += pci_type1.o
diff --git a/arch/x86/lib/cmd_mtrr.c b/arch/x86/lib/cmd_mtrr.c
new file mode 100644
index 0000000..7e0506b
--- /dev/null
+++ b/arch/x86/lib/cmd_mtrr.c
@@ -0,0 +1,138 @@
+/*
+ * (C) Copyright 2014 Google, Inc
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/msr.h>
+#include <asm/mtrr.h>
+
+static const char *const mtrr_type_name[MTRR_TYPE_COUNT] = {
+ "Uncacheable",
+ "Combine",
+ "2",
+ "3",
+ "Through",
+ "Protect",
+ "Back",
+};
+
+static int do_mtrr_list(void)
+{
+ int i;
+
+ printf("Reg Valid Write-type %-16s %-16s %-16s\n", "Base ||",
+ "Mask ||", "Size ||");
+ for (i = 0; i < MTRR_COUNT; i++) {
+ const char *type = "Invalid";
+ uint64_t base, mask, size;
+ bool valid;
+
+ base = native_read_msr(MTRR_PHYS_BASE_MSR(i));
+ mask = native_read_msr(MTRR_PHYS_MASK_MSR(i));
+ size = ~mask & ((1ULL << CONFIG_CPU_ADDR_BITS) - 1);
+ size |= (1 << 12) - 1;
+ size += 1;
+ valid = mask & MTRR_PHYS_MASK_VALID;
+ type = mtrr_type_name[base & MTRR_BASE_TYPE_MASK];
+ printf("%d %-5s %-12s %016llx %016llx %016llx\n", i,
+ valid ? "Y" : "N", type, base, mask, size);
+ }
+
+ return 0;
+}
+
+static int do_mtrr_set(uint reg, int argc, char * const argv[])
+{
+ const char *typename = argv[0];
+ struct mtrr_state state;
+ uint32_t start, size;
+ uint64_t base, mask;
+ int i, type = -1;
+ bool valid;
+
+ if (argc < 3)
+ return CMD_RET_USAGE;
+ for (i = 0; i < MTRR_TYPE_COUNT; i++) {
+ if (*typename == *mtrr_type_name[i])
+ type = i;
+ }
+ if (type == -1) {
+ printf("Invalid type name %s\n", typename);
+ return CMD_RET_USAGE;
+ }
+ start = simple_strtoul(argv[1], NULL, 16);
+ size = simple_strtoul(argv[2], NULL, 16);
+
+ base = start | type;
+ valid = native_read_msr(MTRR_PHYS_MASK_MSR(reg)) & MTRR_PHYS_MASK_VALID;
+ mask = ~((uint64_t)size - 1);
+ mask &= (1ULL << CONFIG_CPU_ADDR_BITS) - 1;
+ if (valid)
+ mask |= MTRR_PHYS_MASK_VALID;
+
+ printf("base=%llx, mask=%llx\n", base, mask);
+ mtrr_open(&state);
+ wrmsrl(MTRR_PHYS_BASE_MSR(reg), base);
+ wrmsrl(MTRR_PHYS_MASK_MSR(reg), mask);
+ mtrr_close(&state);
+
+ return 0;
+}
+
+static int mtrr_set_valid(int reg, bool valid)
+{
+ struct mtrr_state state;
+ uint64_t mask;
+
+ mtrr_open(&state);
+ mask = native_read_msr(MTRR_PHYS_MASK_MSR(reg));
+ if (valid)
+ mask |= MTRR_PHYS_MASK_VALID;
+ else
+ mask &= ~MTRR_PHYS_MASK_VALID;
+ wrmsrl(MTRR_PHYS_MASK_MSR(reg), mask);
+ mtrr_close(&state);
+
+ return 0;
+}
+
+static int do_mtrr(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ const char *cmd;
+ uint reg;
+
+ cmd = argv[1];
+ if (argc < 2 || *cmd == 'l')
+ return do_mtrr_list();
+ argc -= 2;
+ argv += 2;
+ if (argc <= 0)
+ return CMD_RET_USAGE;
+ reg = simple_strtoul(argv[0], NULL, 16);
+ if (reg >= MTRR_COUNT) {
+ printf("Invalid register number\n");
+ return CMD_RET_USAGE;
+ }
+ if (*cmd == 'e')
+ return mtrr_set_valid(reg, true);
+ else if (*cmd == 'd')
+ return mtrr_set_valid(reg, false);
+ else if (*cmd == 's')
+ return do_mtrr_set(reg, argc - 1, argv + 1);
+ else
+ return CMD_RET_USAGE;
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ mtrr, 6, 1, do_mtrr,
+ "Use x86 memory type range registers (32-bit only)",
+ "[list] - list current registers\n"
+ "set <reg> <type> <start> <size> - set a register\n"
+ "\t<type> is Uncacheable, Combine, Through, Protect, Back\n"
+ "disable <reg> - disable a register\n"
+ "ensable <reg> - enable a register"
+);
diff --git a/doc/README.x86 b/doc/README.x86
index 5fab044..b474161 100644
--- a/doc/README.x86
+++ b/doc/README.x86
@@ -110,9 +110,25 @@ be turned on. Not every device on the board is configured via devie tree, but
more and more devices will be added as time goes by. Check out the directory
arch/x86/dts/ for these device tree source files.
+Useful Commands
+---------------
+
+In keeping with the U-Boot philosophy of providing functions to check and
+adjust internal settings, there are several x86-specific commands that may be
+useful:
+
+hob - Display information about Firmware Support Package (FSP) Hand-off
+ Block. This is only available on platforms which use FSP, mostly
+ Atom.
+iod - Display I/O memory
+iow - Write I/O memory
+mtrr - List and set the Memory Type Range Registers (MTRR). These are used to
+ tell the CPU whether memory is cacheable and if so the cache write
+ mode to use. U-Boot sets up some reasonable values but you can
+ adjust then with this command.
+
TODO List
---------
-- MTRR support (for performance)
- Audio
- Chrome OS verified boot
- SMI and ACPI support, to provide platform info and facilities to Linux
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 02/22] x86: Drop RAMTOP Kconfig
2015-01-01 23:17 ` [U-Boot] [PATCH v2 02/22] x86: Drop RAMTOP Kconfig Simon Glass
@ 2015-01-04 2:26 ` Bin Meng
2015-01-05 17:39 ` Simon Glass
0 siblings, 1 reply; 55+ messages in thread
From: Bin Meng @ 2015-01-04 2:26 UTC (permalink / raw)
To: u-boot
On Fri, Jan 2, 2015 at 7:17 AM, Simon Glass <sjg@chromium.org> wrote:
> We don't need this in U-Boot since we calculate it based on available memory.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2:
> - Remove CONFIG_RAMTOP from mtrr.h in this patch
>
> arch/x86/Kconfig | 4 ----
> arch/x86/include/asm/mtrr.h | 8 --------
> 2 files changed, 12 deletions(-)
>
> diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
> index 7d007bb..e992e64 100644
> --- a/arch/x86/Kconfig
> +++ b/arch/x86/Kconfig
> @@ -47,10 +47,6 @@ config RAMBASE
> hex
> default 0x100000
>
> -config RAMTOP
> - hex
> - default 0x200000
> -
> config XIP_ROM_SIZE
> hex
> default ROM_SIZE
> diff --git a/arch/x86/include/asm/mtrr.h b/arch/x86/include/asm/mtrr.h
> index 5f05a48..dcc995d 100644
> --- a/arch/x86/include/asm/mtrr.h
> +++ b/arch/x86/include/asm/mtrr.h
> @@ -100,10 +100,6 @@ static inline long x86_mtrr_rom_cache_var_index(void) { return -1; }
>
> #endif
>
> -#if !defined(CONFIG_RAMTOP)
> -# error "CONFIG_RAMTOP not defined"
> -#endif
> -
> #if ((CONFIG_XIP_ROM_SIZE & (CONFIG_XIP_ROM_SIZE - 1)) != 0)
> # error "CONFIG_XIP_ROM_SIZE is not a power of 2"
> #endif
> @@ -114,8 +110,4 @@ static inline long x86_mtrr_rom_cache_var_index(void) { return -1; }
>
> #define CACHE_ROM_BASE (((1 << 20) - (CONFIG_CACHE_ROM_SIZE >> 12)) << 12)
>
> -#if (CONFIG_RAMTOP & (CONFIG_RAMTOP - 1)) != 0
> -# error "CONFIG_RAMTOP must be a power of 2"
> -#endif
> -
> #endif
> --
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 09/22] x86: ivybridge: Only run the Video BIOS when video is enabled
2015-01-01 23:18 ` [U-Boot] [PATCH v2 09/22] x86: ivybridge: Only run the Video BIOS when video is enabled Simon Glass
@ 2015-01-04 2:31 ` Bin Meng
2015-01-05 17:40 ` Simon Glass
0 siblings, 1 reply; 55+ messages in thread
From: Bin Meng @ 2015-01-04 2:31 UTC (permalink / raw)
To: u-boot
On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
> This takes about about 700ms on link when running natively and 900ms when
> running using the emulator. It is a waste of time if video is not enabled,
> so don't bother running the video BIOS in that case.
>
> We could add a command to run the video BIOS later when needed, but this is
> not considered at present.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2:
> - Use CONFIG_VIDEO directly to control running the video BIOS
>
> arch/x86/cpu/ivybridge/gma.c | 9 ++++++++-
> 1 file changed, 8 insertions(+), 1 deletion(-)
>
> diff --git a/arch/x86/cpu/ivybridge/gma.c b/arch/x86/cpu/ivybridge/gma.c
> index 3d7f740..cf4f87c 100644
> --- a/arch/x86/cpu/ivybridge/gma.c
> +++ b/arch/x86/cpu/ivybridge/gma.c
> @@ -15,6 +15,7 @@
> #include <asm/pci.h>
> #include <asm/arch/pch.h>
> #include <asm/arch/sandybridge.h>
> +#include <linux/kconfig.h>
>
> struct gt_powermeter {
> u16 reg;
> @@ -730,6 +731,9 @@ static int int15_handler(void)
> int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
> const void *blob, int node)
> {
> +#ifdef CONFIG_VIDEO
> + ulong start;
> +#endif
> void *gtt_bar;
> u32 reg32;
> int ret;
> @@ -745,8 +749,11 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
> if (ret)
> return ret;
>
> +#ifdef CONFIG_VIDEO
> + start = get_timer(0);
> ret = pci_run_vga_bios(dev, int15_handler, false);
> -
> + debug("BIOS ran in %lums\n", get_timer(start));
> +#endif
> /* Post VBIOS init */
> ret = gma_pm_init_post_vbios(gtt_bar, blob, node);
> if (ret)
> --
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 15/22] x86: ivybridge: Set up an MTRR for the video frame buffer
2015-01-01 23:18 ` [U-Boot] [PATCH v2 15/22] x86: ivybridge: Set up an MTRR for the video frame buffer Simon Glass
@ 2015-01-04 3:18 ` Bin Meng
2015-01-04 3:20 ` Simon Glass
0 siblings, 1 reply; 55+ messages in thread
From: Bin Meng @ 2015-01-04 3:18 UTC (permalink / raw)
To: u-boot
Hi Simon,
On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
> Set the frame buffer to write-combining. This makes it faster, although for
> scrolling write-through is even faster for U-Boot.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2:
> - Remove definition of 'ulong start' from this patch
>
> arch/x86/cpu/ivybridge/gma.c | 7 +++++++
> 1 file changed, 7 insertions(+)
>
> diff --git a/arch/x86/cpu/ivybridge/gma.c b/arch/x86/cpu/ivybridge/gma.c
> index cf4f87c..6cf9654 100644
> --- a/arch/x86/cpu/ivybridge/gma.c
> +++ b/arch/x86/cpu/ivybridge/gma.c
> @@ -12,6 +12,7 @@
> #include <fdtdec.h>
> #include <pci_rom.h>
> #include <asm/io.h>
> +#include <asm/mtrr.h>
> #include <asm/pci.h>
> #include <asm/arch/pch.h>
> #include <asm/arch/sandybridge.h>
> @@ -735,6 +736,7 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
> ulong start;
> #endif
> void *gtt_bar;
> + ulong base;
> u32 reg32;
> int ret;
>
> @@ -743,6 +745,11 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
> reg32 |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO;
> pci_write_config32(dev, PCI_COMMAND, reg32);
>
> + /* Use write-combining for the graphics memory, 256MB */
> + base = pci_read_bar32(hose, dev, 2);
> + mtrr_add_request(MTRR_TYPE_WRCOMB, base, 256 << 20);
> + mtrr_commit(true);
> +
> gtt_bar = (void *)pci_read_bar32(pci_bus_to_hose(0), dev, 0);
> debug("GT bar %p\n", gtt_bar);
> ret = gma_pm_init_pre_vbios(gtt_bar);
> --
Do you have any comments regarding to what I said in
http://lists.denx.de/pipermail/u-boot/2014-December/199955.html?
Regards,
Bin
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 15/22] x86: ivybridge: Set up an MTRR for the video frame buffer
2015-01-04 3:18 ` Bin Meng
@ 2015-01-04 3:20 ` Simon Glass
2015-01-04 3:28 ` Bin Meng
0 siblings, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-04 3:20 UTC (permalink / raw)
To: u-boot
Hi Bin,
On 3 January 2015 at 20:18, Bin Meng <bmeng.cn@gmail.com> wrote:
> Hi Simon,
>
> On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
>> Set the frame buffer to write-combining. This makes it faster, although for
>> scrolling write-through is even faster for U-Boot.
>>
>> Signed-off-by: Simon Glass <sjg@chromium.org>
>> ---
>>
>> Changes in v2:
>> - Remove definition of 'ulong start' from this patch
>>
>> arch/x86/cpu/ivybridge/gma.c | 7 +++++++
>> 1 file changed, 7 insertions(+)
>>
>> diff --git a/arch/x86/cpu/ivybridge/gma.c b/arch/x86/cpu/ivybridge/gma.c
>> index cf4f87c..6cf9654 100644
>> --- a/arch/x86/cpu/ivybridge/gma.c
>> +++ b/arch/x86/cpu/ivybridge/gma.c
>> @@ -12,6 +12,7 @@
>> #include <fdtdec.h>
>> #include <pci_rom.h>
>> #include <asm/io.h>
>> +#include <asm/mtrr.h>
>> #include <asm/pci.h>
>> #include <asm/arch/pch.h>
>> #include <asm/arch/sandybridge.h>
>> @@ -735,6 +736,7 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
>> ulong start;
>> #endif
>> void *gtt_bar;
>> + ulong base;
>> u32 reg32;
>> int ret;
>>
>> @@ -743,6 +745,11 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
>> reg32 |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO;
>> pci_write_config32(dev, PCI_COMMAND, reg32);
>>
>> + /* Use write-combining for the graphics memory, 256MB */
>> + base = pci_read_bar32(hose, dev, 2);
>> + mtrr_add_request(MTRR_TYPE_WRCOMB, base, 256 << 20);
>> + mtrr_commit(true);
>> +
>> gtt_bar = (void *)pci_read_bar32(pci_bus_to_hose(0), dev, 0);
>> debug("GT bar %p\n", gtt_bar);
>> ret = gma_pm_init_pre_vbios(gtt_bar);
>> --
>
> Do you have any comments regarding to what I said in
> http://lists.denx.de/pipermail/u-boot/2014-December/199955.html?
Ah yes I meant to say that I did look at a function to return the BAR
size, but it involves changing the BAR. I have a patch out to convert
PCI to driver model and there we will be able to store the size. So
perhaps we should revisit this later?
Regards,
Simon
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 15/22] x86: ivybridge: Set up an MTRR for the video frame buffer
2015-01-04 3:20 ` Simon Glass
@ 2015-01-04 3:28 ` Bin Meng
2015-01-05 17:41 ` Simon Glass
0 siblings, 1 reply; 55+ messages in thread
From: Bin Meng @ 2015-01-04 3:28 UTC (permalink / raw)
To: u-boot
Hi Simon,
On Sun, Jan 4, 2015 at 11:20 AM, Simon Glass <sjg@chromium.org> wrote:
> Hi Bin,
>
> On 3 January 2015 at 20:18, Bin Meng <bmeng.cn@gmail.com> wrote:
>> Hi Simon,
>>
>> On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
>>> Set the frame buffer to write-combining. This makes it faster, although for
>>> scrolling write-through is even faster for U-Boot.
>>>
>>> Signed-off-by: Simon Glass <sjg@chromium.org>
>>> ---
>>>
>>> Changes in v2:
>>> - Remove definition of 'ulong start' from this patch
>>>
>>> arch/x86/cpu/ivybridge/gma.c | 7 +++++++
>>> 1 file changed, 7 insertions(+)
>>>
>>> diff --git a/arch/x86/cpu/ivybridge/gma.c b/arch/x86/cpu/ivybridge/gma.c
>>> index cf4f87c..6cf9654 100644
>>> --- a/arch/x86/cpu/ivybridge/gma.c
>>> +++ b/arch/x86/cpu/ivybridge/gma.c
>>> @@ -12,6 +12,7 @@
>>> #include <fdtdec.h>
>>> #include <pci_rom.h>
>>> #include <asm/io.h>
>>> +#include <asm/mtrr.h>
>>> #include <asm/pci.h>
>>> #include <asm/arch/pch.h>
>>> #include <asm/arch/sandybridge.h>
>>> @@ -735,6 +736,7 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
>>> ulong start;
>>> #endif
>>> void *gtt_bar;
>>> + ulong base;
>>> u32 reg32;
>>> int ret;
>>>
>>> @@ -743,6 +745,11 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
>>> reg32 |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO;
>>> pci_write_config32(dev, PCI_COMMAND, reg32);
>>>
>>> + /* Use write-combining for the graphics memory, 256MB */
>>> + base = pci_read_bar32(hose, dev, 2);
>>> + mtrr_add_request(MTRR_TYPE_WRCOMB, base, 256 << 20);
>>> + mtrr_commit(true);
>>> +
>>> gtt_bar = (void *)pci_read_bar32(pci_bus_to_hose(0), dev, 0);
>>> debug("GT bar %p\n", gtt_bar);
>>> ret = gma_pm_init_pre_vbios(gtt_bar);
>>> --
>>
>> Do you have any comments regarding to what I said in
>> http://lists.denx.de/pipermail/u-boot/2014-December/199955.html?
>
> Ah yes I meant to say that I did look at a function to return the BAR
> size, but it involves changing the BAR. I have a patch out to convert
> PCI to driver model and there we will be able to store the size. So
> perhaps we should revisit this later?
>
Sounds good. Let's revisit it later.
Regards,
Bin
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 20/22] x86: Disable CAR before relocation on platforms that need it
2015-01-01 23:18 ` [U-Boot] [PATCH v2 20/22] x86: Disable CAR before relocation on platforms that need it Simon Glass
@ 2015-01-04 3:53 ` Bin Meng
2015-01-05 17:41 ` Simon Glass
0 siblings, 1 reply; 55+ messages in thread
From: Bin Meng @ 2015-01-04 3:53 UTC (permalink / raw)
To: u-boot
Hi Simon,
On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
> For platforms with CAR we should disable it before relocation. Check if
> this function is available and call it if so.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2:
> - Use a simple call instruction to call car_uninit
>
> arch/x86/cpu/start.S | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/arch/x86/cpu/start.S b/arch/x86/cpu/start.S
> index 125782c..be8a2dc 100644
> --- a/arch/x86/cpu/start.S
> +++ b/arch/x86/cpu/start.S
> @@ -205,6 +205,15 @@ board_init_f_r_trampoline:
> /* Setup global descriptor table so gd->xyz works */
> call setup_gdt
>
> + /* Set if we need to disable CAR */
> +.weak car_uninit
> + movl $car_uninit, %eax
> + cmpl $0, %eax
> + jz 1f
> +
> + /* Pass return address in ebx */
The comment need to be fixed, or just simply remove this.
> + call car_uninit
> +1:
> /* Re-enter U-Boot by calling board_init_f_r */
> call board_init_f_r
>
> --
Regards,
Bin
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 22/22] x86: Add an 'mtrr' command to list and adjust MTRRs
2015-01-01 23:18 ` [U-Boot] [PATCH v2 22/22] x86: Add an 'mtrr' command to list and adjust MTRRs Simon Glass
@ 2015-01-04 4:13 ` Bin Meng
2015-01-05 17:41 ` Simon Glass
0 siblings, 1 reply; 55+ messages in thread
From: Bin Meng @ 2015-01-04 4:13 UTC (permalink / raw)
To: u-boot
On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
> It is useful to be able to see the MTRR setup in U-Boot. Add a command
> to list the state of the variable MTRR registers and allow them to be
> changed.
>
> Update the documentation to list some of the available commands.
>
> This does not support fixed MTRRs as yet.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2:
> - Move cmd_mtrr to arch/x86/lib
> - Correct 'platform' typo
>
> arch/x86/lib/Makefile | 1 +
> arch/x86/lib/cmd_mtrr.c | 138 ++++++++++++++++++++++++++++++++++++++++++++++++
> doc/README.x86 | 18 ++++++-
> 3 files changed, 156 insertions(+), 1 deletion(-)
> create mode 100644 arch/x86/lib/cmd_mtrr.c
>
> diff --git a/arch/x86/lib/Makefile b/arch/x86/lib/Makefile
> index 73262d7..32d7b98 100644
> --- a/arch/x86/lib/Makefile
> +++ b/arch/x86/lib/Makefile
> @@ -14,6 +14,7 @@ obj-$(CONFIG_HAVE_FSP) += cmd_hob.o
> obj-y += gcc.o
> obj-y += init_helpers.o
> obj-y += interrupts.o
> +obj-y += cmd_mtrr.o
> obj-$(CONFIG_SYS_PCAT_INTERRUPTS) += pcat_interrupts.o
> obj-$(CONFIG_SYS_PCAT_TIMER) += pcat_timer.o
> obj-$(CONFIG_PCI) += pci_type1.o
> diff --git a/arch/x86/lib/cmd_mtrr.c b/arch/x86/lib/cmd_mtrr.c
> new file mode 100644
> index 0000000..7e0506b
> --- /dev/null
> +++ b/arch/x86/lib/cmd_mtrr.c
> @@ -0,0 +1,138 @@
> +/*
> + * (C) Copyright 2014 Google, Inc
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/msr.h>
> +#include <asm/mtrr.h>
> +
> +static const char *const mtrr_type_name[MTRR_TYPE_COUNT] = {
> + "Uncacheable",
> + "Combine",
> + "2",
> + "3",
> + "Through",
> + "Protect",
> + "Back",
> +};
> +
> +static int do_mtrr_list(void)
> +{
> + int i;
> +
> + printf("Reg Valid Write-type %-16s %-16s %-16s\n", "Base ||",
> + "Mask ||", "Size ||");
> + for (i = 0; i < MTRR_COUNT; i++) {
> + const char *type = "Invalid";
> + uint64_t base, mask, size;
> + bool valid;
> +
> + base = native_read_msr(MTRR_PHYS_BASE_MSR(i));
> + mask = native_read_msr(MTRR_PHYS_MASK_MSR(i));
> + size = ~mask & ((1ULL << CONFIG_CPU_ADDR_BITS) - 1);
> + size |= (1 << 12) - 1;
> + size += 1;
> + valid = mask & MTRR_PHYS_MASK_VALID;
> + type = mtrr_type_name[base & MTRR_BASE_TYPE_MASK];
> + printf("%d %-5s %-12s %016llx %016llx %016llx\n", i,
> + valid ? "Y" : "N", type, base, mask, size);
> + }
> +
> + return 0;
> +}
> +
> +static int do_mtrr_set(uint reg, int argc, char * const argv[])
> +{
> + const char *typename = argv[0];
> + struct mtrr_state state;
> + uint32_t start, size;
> + uint64_t base, mask;
> + int i, type = -1;
> + bool valid;
> +
> + if (argc < 3)
> + return CMD_RET_USAGE;
> + for (i = 0; i < MTRR_TYPE_COUNT; i++) {
> + if (*typename == *mtrr_type_name[i])
> + type = i;
> + }
> + if (type == -1) {
> + printf("Invalid type name %s\n", typename);
> + return CMD_RET_USAGE;
> + }
> + start = simple_strtoul(argv[1], NULL, 16);
> + size = simple_strtoul(argv[2], NULL, 16);
> +
> + base = start | type;
> + valid = native_read_msr(MTRR_PHYS_MASK_MSR(reg)) & MTRR_PHYS_MASK_VALID;
> + mask = ~((uint64_t)size - 1);
> + mask &= (1ULL << CONFIG_CPU_ADDR_BITS) - 1;
> + if (valid)
> + mask |= MTRR_PHYS_MASK_VALID;
> +
> + printf("base=%llx, mask=%llx\n", base, mask);
> + mtrr_open(&state);
> + wrmsrl(MTRR_PHYS_BASE_MSR(reg), base);
> + wrmsrl(MTRR_PHYS_MASK_MSR(reg), mask);
> + mtrr_close(&state);
> +
> + return 0;
> +}
> +
> +static int mtrr_set_valid(int reg, bool valid)
> +{
> + struct mtrr_state state;
> + uint64_t mask;
> +
> + mtrr_open(&state);
> + mask = native_read_msr(MTRR_PHYS_MASK_MSR(reg));
> + if (valid)
> + mask |= MTRR_PHYS_MASK_VALID;
> + else
> + mask &= ~MTRR_PHYS_MASK_VALID;
> + wrmsrl(MTRR_PHYS_MASK_MSR(reg), mask);
> + mtrr_close(&state);
> +
> + return 0;
> +}
> +
> +static int do_mtrr(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
> +{
> + const char *cmd;
> + uint reg;
> +
> + cmd = argv[1];
> + if (argc < 2 || *cmd == 'l')
> + return do_mtrr_list();
> + argc -= 2;
> + argv += 2;
> + if (argc <= 0)
> + return CMD_RET_USAGE;
> + reg = simple_strtoul(argv[0], NULL, 16);
> + if (reg >= MTRR_COUNT) {
> + printf("Invalid register number\n");
> + return CMD_RET_USAGE;
> + }
> + if (*cmd == 'e')
> + return mtrr_set_valid(reg, true);
> + else if (*cmd == 'd')
> + return mtrr_set_valid(reg, false);
> + else if (*cmd == 's')
> + return do_mtrr_set(reg, argc - 1, argv + 1);
> + else
> + return CMD_RET_USAGE;
> +
> + return 0;
> +}
> +
> +U_BOOT_CMD(
> + mtrr, 6, 1, do_mtrr,
> + "Use x86 memory type range registers (32-bit only)",
> + "[list] - list current registers\n"
> + "set <reg> <type> <start> <size> - set a register\n"
> + "\t<type> is Uncacheable, Combine, Through, Protect, Back\n"
> + "disable <reg> - disable a register\n"
> + "ensable <reg> - enable a register"
> +);
> diff --git a/doc/README.x86 b/doc/README.x86
> index 5fab044..b474161 100644
> --- a/doc/README.x86
> +++ b/doc/README.x86
> @@ -110,9 +110,25 @@ be turned on. Not every device on the board is configured via devie tree, but
> more and more devices will be added as time goes by. Check out the directory
> arch/x86/dts/ for these device tree source files.
>
> +Useful Commands
> +---------------
> +
> +In keeping with the U-Boot philosophy of providing functions to check and
> +adjust internal settings, there are several x86-specific commands that may be
> +useful:
> +
> +hob - Display information about Firmware Support Package (FSP) Hand-off
> + Block. This is only available on platforms which use FSP, mostly
> + Atom.
> +iod - Display I/O memory
> +iow - Write I/O memory
> +mtrr - List and set the Memory Type Range Registers (MTRR). These are used to
> + tell the CPU whether memory is cacheable and if so the cache write
> + mode to use. U-Boot sets up some reasonable values but you can
> + adjust then with this command.
> +
> TODO List
> ---------
> -- MTRR support (for performance)
> - Audio
> - Chrome OS verified boot
> - SMI and ACPI support, to provide platform info and facilities to Linux
> --
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 01/22] x86: Correct XIP_ROM_SIZE
2015-01-01 23:17 ` [U-Boot] [PATCH v2 01/22] x86: Correct XIP_ROM_SIZE Simon Glass
@ 2015-01-05 17:39 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:39 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:17, Simon Glass <sjg@chromium.org> wrote:
> This should default to the size of the ROM for faster execution before
> relocation.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 02/22] x86: Drop RAMTOP Kconfig
2015-01-04 2:26 ` Bin Meng
@ 2015-01-05 17:39 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:39 UTC (permalink / raw)
To: u-boot
On 3 January 2015 at 19:26, Bin Meng <bmeng.cn@gmail.com> wrote:
> On Fri, Jan 2, 2015 at 7:17 AM, Simon Glass <sjg@chromium.org> wrote:
>> We don't need this in U-Boot since we calculate it based on available memory.
>>
>> Signed-off-by: Simon Glass <sjg@chromium.org>
>> ---
>>
>> Changes in v2:
>> - Remove CONFIG_RAMTOP from mtrr.h in this patch
>>
>> arch/x86/Kconfig | 4 ----
>> arch/x86/include/asm/mtrr.h | 8 --------
>> 2 files changed, 12 deletions(-)
>>
>> diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
>> index 7d007bb..e992e64 100644
>> --- a/arch/x86/Kconfig
>> +++ b/arch/x86/Kconfig
>> @@ -47,10 +47,6 @@ config RAMBASE
>> hex
>> default 0x100000
>>
>> -config RAMTOP
>> - hex
>> - default 0x200000
>> -
>> config XIP_ROM_SIZE
>> hex
>> default ROM_SIZE
>> diff --git a/arch/x86/include/asm/mtrr.h b/arch/x86/include/asm/mtrr.h
>> index 5f05a48..dcc995d 100644
>> --- a/arch/x86/include/asm/mtrr.h
>> +++ b/arch/x86/include/asm/mtrr.h
>> @@ -100,10 +100,6 @@ static inline long x86_mtrr_rom_cache_var_index(void) { return -1; }
>>
>> #endif
>>
>> -#if !defined(CONFIG_RAMTOP)
>> -# error "CONFIG_RAMTOP not defined"
>> -#endif
>> -
>> #if ((CONFIG_XIP_ROM_SIZE & (CONFIG_XIP_ROM_SIZE - 1)) != 0)
>> # error "CONFIG_XIP_ROM_SIZE is not a power of 2"
>> #endif
>> @@ -114,8 +110,4 @@ static inline long x86_mtrr_rom_cache_var_index(void) { return -1; }
>>
>> #define CACHE_ROM_BASE (((1 << 20) - (CONFIG_CACHE_ROM_SIZE >> 12)) << 12)
>>
>> -#if (CONFIG_RAMTOP & (CONFIG_RAMTOP - 1)) != 0
>> -# error "CONFIG_RAMTOP must be a power of 2"
>> -#endif
>> -
>> #endif
>> --
>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 03/22] x86: Correct ifdtool microcode calculation
2015-01-01 23:17 ` [U-Boot] [PATCH v2 03/22] x86: Correct ifdtool microcode calculation Simon Glass
@ 2015-01-05 17:39 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:39 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:17, Simon Glass <sjg@chromium.org> wrote:
> This currently assumes that U-Boot resides at the start of ROM. Update
> it to remove this assumption.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> Tested-by: Bin Meng <bmeng.cn@gmail.com>
> ---
>
> Changes in v2: None
>
> tools/ifdtool.c | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 06/22] x86: video: Add a debug() to display the frame buffer address
2015-01-01 23:17 ` [U-Boot] [PATCH v2 06/22] x86: video: Add a debug() to display the frame buffer address Simon Glass
@ 2015-01-05 17:39 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:39 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:17, Simon Glass <sjg@chromium.org> wrote:
> Provide a way to display this address when booting.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> drivers/video/x86_fb.c | 1 +
> 1 file changed, 1 insertion(+)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 07/22] x86: pci: Don't return a vesa mode when there is not video
2015-01-01 23:18 ` [U-Boot] [PATCH v2 07/22] x86: pci: Don't return a vesa mode when there is not video Simon Glass
@ 2015-01-05 17:39 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:39 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> If the video has not been set up, we should not return a success code. This
> can be detected by seeing if any of the variables are non-zero.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> drivers/pci/pci_rom.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 08/22] x86: video: Add debug option to time the BIOS copy
2015-01-01 23:18 ` [U-Boot] [PATCH v2 08/22] x86: video: Add debug option to time the BIOS copy Simon Glass
@ 2015-01-05 17:39 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:39 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> This can be very slow - typically 80ms even on a fast machine since it uses
> the SPI flash to read the data. Add an option to display the time taken.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> ---
>
> Changes in v2: None
>
> drivers/pci/pci_rom.c | 3 +++
> 1 file changed, 3 insertions(+)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 09/22] x86: ivybridge: Only run the Video BIOS when video is enabled
2015-01-04 2:31 ` Bin Meng
@ 2015-01-05 17:40 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:40 UTC (permalink / raw)
To: u-boot
On 3 January 2015 at 19:31, Bin Meng <bmeng.cn@gmail.com> wrote:
> On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
>> This takes about about 700ms on link when running natively and 900ms when
>> running using the emulator. It is a waste of time if video is not enabled,
>> so don't bother running the video BIOS in that case.
>>
>> We could add a command to run the video BIOS later when needed, but this is
>> not considered at present.
>>
>> Signed-off-by: Simon Glass <sjg@chromium.org>
>> ---
>>
>> Changes in v2:
>> - Use CONFIG_VIDEO directly to control running the video BIOS
>>
>> arch/x86/cpu/ivybridge/gma.c | 9 ++++++++-
>> 1 file changed, 8 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/x86/cpu/ivybridge/gma.c b/arch/x86/cpu/ivybridge/gma.c
>> index 3d7f740..cf4f87c 100644
>> --- a/arch/x86/cpu/ivybridge/gma.c
>> +++ b/arch/x86/cpu/ivybridge/gma.c
>> @@ -15,6 +15,7 @@
>> #include <asm/pci.h>
>> #include <asm/arch/pch.h>
>> #include <asm/arch/sandybridge.h>
>> +#include <linux/kconfig.h>
>>
>> struct gt_powermeter {
>> u16 reg;
>> @@ -730,6 +731,9 @@ static int int15_handler(void)
>> int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
>> const void *blob, int node)
>> {
>> +#ifdef CONFIG_VIDEO
>> + ulong start;
>> +#endif
>> void *gtt_bar;
>> u32 reg32;
>> int ret;
>> @@ -745,8 +749,11 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
>> if (ret)
>> return ret;
>>
>> +#ifdef CONFIG_VIDEO
>> + start = get_timer(0);
>> ret = pci_run_vga_bios(dev, int15_handler, false);
>> -
>> + debug("BIOS ran in %lums\n", get_timer(start));
>> +#endif
>> /* Post VBIOS init */
>> ret = gma_pm_init_post_vbios(gtt_bar, blob, node);
>> if (ret)
>> --
>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 10/22] x86: Use cache, don't clear the display in video BIOS
2015-01-01 23:18 ` [U-Boot] [PATCH v2 10/22] x86: Use cache, don't clear the display in video BIOS Simon Glass
@ 2015-01-05 17:40 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:40 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> There is no need to run with the cache disabled, and there is no point in
> clearing the display frame buffer since U-Boot does it later.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> arch/x86/lib/bios.c | 5 ++---
> 1 file changed, 2 insertions(+), 3 deletions(-)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 11/22] x86: Tidy up VESA mode numbers
2015-01-01 23:18 ` [U-Boot] [PATCH v2 11/22] x86: Tidy up VESA mode numbers Simon Glass
@ 2015-01-05 17:40 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:40 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> There are some bits which should be ignored when displaying the mode number.
> Make sure that they are not included in the mode that is displayed.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> arch/x86/lib/bios.c | 11 +++++++----
> 1 file changed, 7 insertions(+), 4 deletions(-)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 12/22] x86: pci: Display vesa modes in hex
2015-01-01 23:18 ` [U-Boot] [PATCH v2 12/22] x86: pci: Display vesa modes in hex Simon Glass
@ 2015-01-05 17:40 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:40 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> The hex value is more commonly understood, so use that instead of decimal.
> Add a 0x prefix to avoid confusion.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> ---
>
> Changes in v2: None
>
> drivers/pci/pci_rom.c | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 13/22] x86: ivybridge: Drop support for ROM caching
2015-01-01 23:18 ` [U-Boot] [PATCH v2 13/22] x86: ivybridge: Drop support for ROM caching Simon Glass
@ 2015-01-05 17:40 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:40 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> This is set up along with CAR (Cache-as-RAM) anyway. When we relocate we
> don't really need ROM caching (we read the VGA BIOS from ROM but that is
> about it)
>
> Drop it.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> arch/x86/cpu/ivybridge/cpu.c | 25 -------------------------
> 1 file changed, 25 deletions(-)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 14/22] x86: Add support for MTRRs
2015-01-01 23:18 ` [U-Boot] [PATCH v2 14/22] x86: Add support for MTRRs Simon Glass
@ 2015-01-05 17:41 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:41 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> Memory Type Range Registers are used to tell the CPU whether memory is
> cacheable and if so the cache write mode to use.
>
> Clean up the existing header file to follow style, and remove the unneeded
> code.
>
> These can speed up booting so should be supported. Add these to global_data
> so they can be requested while booting. We will apply the changes during
> relocation (in a later commit).
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> arch/x86/cpu/Makefile | 1 +
> arch/x86/cpu/coreboot/coreboot.c | 22 +++---
> arch/x86/cpu/ivybridge/car.S | 12 +--
> arch/x86/cpu/mtrr.c | 81 +++++++++++++++++++
> arch/x86/include/asm/global_data.h | 15 ++++
> arch/x86/include/asm/mtrr.h | 157 +++++++++++++++++--------------------
> 6 files changed, 187 insertions(+), 101 deletions(-)
> create mode 100644 arch/x86/cpu/mtrr.c
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 15/22] x86: ivybridge: Set up an MTRR for the video frame buffer
2015-01-04 3:28 ` Bin Meng
@ 2015-01-05 17:41 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:41 UTC (permalink / raw)
To: u-boot
On 3 January 2015 at 20:28, Bin Meng <bmeng.cn@gmail.com> wrote:
> Hi Simon,
>
> On Sun, Jan 4, 2015 at 11:20 AM, Simon Glass <sjg@chromium.org> wrote:
>> Hi Bin,
>>
>> On 3 January 2015 at 20:18, Bin Meng <bmeng.cn@gmail.com> wrote:
>>> Hi Simon,
>>>
>>> On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
>>>> Set the frame buffer to write-combining. This makes it faster, although for
>>>> scrolling write-through is even faster for U-Boot.
>>>>
>>>> Signed-off-by: Simon Glass <sjg@chromium.org>
>>>> ---
>>>>
>>>> Changes in v2:
>>>> - Remove definition of 'ulong start' from this patch
>>>>
>>>> arch/x86/cpu/ivybridge/gma.c | 7 +++++++
>>>> 1 file changed, 7 insertions(+)
>>>>
>>>> diff --git a/arch/x86/cpu/ivybridge/gma.c b/arch/x86/cpu/ivybridge/gma.c
>>>> index cf4f87c..6cf9654 100644
>>>> --- a/arch/x86/cpu/ivybridge/gma.c
>>>> +++ b/arch/x86/cpu/ivybridge/gma.c
>>>> @@ -12,6 +12,7 @@
>>>> #include <fdtdec.h>
>>>> #include <pci_rom.h>
>>>> #include <asm/io.h>
>>>> +#include <asm/mtrr.h>
>>>> #include <asm/pci.h>
>>>> #include <asm/arch/pch.h>
>>>> #include <asm/arch/sandybridge.h>
>>>> @@ -735,6 +736,7 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
>>>> ulong start;
>>>> #endif
>>>> void *gtt_bar;
>>>> + ulong base;
>>>> u32 reg32;
>>>> int ret;
>>>>
>>>> @@ -743,6 +745,11 @@ int gma_func0_init(pci_dev_t dev, struct pci_controller *hose,
>>>> reg32 |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO;
>>>> pci_write_config32(dev, PCI_COMMAND, reg32);
>>>>
>>>> + /* Use write-combining for the graphics memory, 256MB */
>>>> + base = pci_read_bar32(hose, dev, 2);
>>>> + mtrr_add_request(MTRR_TYPE_WRCOMB, base, 256 << 20);
>>>> + mtrr_commit(true);
>>>> +
>>>> gtt_bar = (void *)pci_read_bar32(pci_bus_to_hose(0), dev, 0);
>>>> debug("GT bar %p\n", gtt_bar);
>>>> ret = gma_pm_init_pre_vbios(gtt_bar);
>>>> --
>>>
>>> Do you have any comments regarding to what I said in
>>> http://lists.denx.de/pipermail/u-boot/2014-December/199955.html?
>>
>> Ah yes I meant to say that I did look at a function to return the BAR
>> size, but it involves changing the BAR. I have a patch out to convert
>> PCI to driver model and there we will be able to store the size. So
>> perhaps we should revisit this later?
>>
>
> Sounds good. Let's revisit it later.
OK. I've pinged the PCI driver model thread, and will revisit soonish.
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 16/22] x86: board_f: Adjust x86 boot order for performance
2015-01-01 23:18 ` [U-Boot] [PATCH v2 16/22] x86: board_f: Adjust x86 boot order for performance Simon Glass
@ 2015-01-05 17:41 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:41 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> For bare platforms we turn off ROM-caching before calling board_init_f_r()
> It is then very slow to copy U-Boot from ROM to RAM. So adjust the order so
> that the copying happens before we turn off ROM-caching.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> common/board_f.c | 8 +++++---
> 1 file changed, 5 insertions(+), 3 deletions(-)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 17/22] x86: ivybridge: Request MTRRs for DRAM regions
2015-01-01 23:18 ` [U-Boot] [PATCH v2 17/22] x86: ivybridge: Request MTRRs for DRAM regions Simon Glass
@ 2015-01-05 17:41 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:41 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> We should use MTRRs to speed up execution. Add a list of MTRR requests which
> will dealt with when we relocate and run from RAM.
>
> We set RAM as cacheable (with write-back) and registers as non-cacheable.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> arch/x86/cpu/ivybridge/sdram.c | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 18/22] x86: Commit the current MTRRs before relocation
2015-01-01 23:18 ` [U-Boot] [PATCH v2 18/22] x86: Commit the current MTRRs before relocation Simon Glass
@ 2015-01-05 17:41 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:41 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> Once we stop running from ROM we should set up the MTTRs to speed up
> execution. This is only needed for platforms that don't have an FSP.
> Also in the Coreboot case, the MTRRs are set up for us.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> arch/x86/lib/init_helpers.c | 8 ++++++++
> 1 file changed, 8 insertions(+)
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 19/22] x86: ivybridge: Add a way to turn off the CAR
2015-01-01 23:18 ` [U-Boot] [PATCH v2 19/22] x86: ivybridge: Add a way to turn off the CAR Simon Glass
@ 2015-01-05 17:41 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:41 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> Cache-as-RAM should be turned off when we relocate since we want to run from
> RAM. Add a function to perform this task.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2:
> - Remove unused Lhlt code
> - Use a simple 'ret' instruction to return
>
> arch/x86/cpu/ivybridge/car.S | 46 ++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 46 insertions(+)
>
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 20/22] x86: Disable CAR before relocation on platforms that need it
2015-01-04 3:53 ` Bin Meng
@ 2015-01-05 17:41 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:41 UTC (permalink / raw)
To: u-boot
On 3 January 2015 at 20:53, Bin Meng <bmeng.cn@gmail.com> wrote:
> Hi Simon,
>
> On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
>> For platforms with CAR we should disable it before relocation. Check if
>> this function is available and call it if so.
>>
>> Signed-off-by: Simon Glass <sjg@chromium.org>
>> ---
>>
>> Changes in v2:
>> - Use a simple call instruction to call car_uninit
>>
>> arch/x86/cpu/start.S | 9 +++++++++
>> 1 file changed, 9 insertions(+)
>>
>> diff --git a/arch/x86/cpu/start.S b/arch/x86/cpu/start.S
>> index 125782c..be8a2dc 100644
>> --- a/arch/x86/cpu/start.S
>> +++ b/arch/x86/cpu/start.S
>> @@ -205,6 +205,15 @@ board_init_f_r_trampoline:
>> /* Setup global descriptor table so gd->xyz works */
>> call setup_gdt
>>
>> + /* Set if we need to disable CAR */
>> +.weak car_uninit
>> + movl $car_uninit, %eax
>> + cmpl $0, %eax
>> + jz 1f
>> +
>> + /* Pass return address in ebx */
>
> The comment need to be fixed, or just simply remove this.
Applied to u-boot-x86/next.
(With comment removed)
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 21/22] x86: ivybridge: Update microcode early in boot
2015-01-01 23:18 ` [U-Boot] [PATCH v2 21/22] x86: ivybridge: Update microcode early in boot Simon Glass
@ 2015-01-05 17:41 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:41 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:18, Simon Glass <sjg@chromium.org> wrote:
> At present the normal update (which happens much later) does not work. This
> seems to have something to do with the 'no eviction' mode in the CAR, or at
> least moving the microcode update after that causes it not to work.
>
> For now, do an update early on so that it definitely works. Also refuse to
> continue unless the microcode update check (later in boot) is successful.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2:
> - Use constants for microcode MSRs and header length
Applied to u-boot-x86/next.
>
> arch/x86/cpu/ivybridge/car.S | 16 +++++++++++++++
> arch/x86/cpu/ivybridge/cpu.c | 2 +-
> arch/x86/cpu/ivybridge/microcode_intel.c | 26 ++++++++++++++++---------
> arch/x86/dts/link.dts | 3 ---
> arch/x86/include/asm/arch-ivybridge/microcode.h | 6 ++++++
> 5 files changed, 40 insertions(+), 13 deletions(-)
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 22/22] x86: Add an 'mtrr' command to list and adjust MTRRs
2015-01-04 4:13 ` Bin Meng
@ 2015-01-05 17:41 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-05 17:41 UTC (permalink / raw)
To: u-boot
On 3 January 2015 at 21:13, Bin Meng <bmeng.cn@gmail.com> wrote:
> On Fri, Jan 2, 2015 at 7:18 AM, Simon Glass <sjg@chromium.org> wrote:
>> It is useful to be able to see the MTRR setup in U-Boot. Add a command
>> to list the state of the variable MTRR registers and allow them to be
>> changed.
>>
>> Update the documentation to list some of the available commands.
>>
>> This does not support fixed MTRRs as yet.
>>
>> Signed-off-by: Simon Glass <sjg@chromium.org>
>> ---
>>
>> Changes in v2:
>> - Move cmd_mtrr to arch/x86/lib
>> - Correct 'platform' typo
>>
>> arch/x86/lib/Makefile | 1 +
>> arch/x86/lib/cmd_mtrr.c | 138 ++++++++++++++++++++++++++++++++++++++++++++++++
>> doc/README.x86 | 18 ++++++-
>> 3 files changed, 156 insertions(+), 1 deletion(-)
>> create mode 100644 arch/x86/lib/cmd_mtrr.c
>>
[snip]
>
> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Applied to u-boot-x86/next.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES
2015-01-01 23:17 ` [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES Simon Glass
@ 2015-01-20 0:33 ` Simon Glass
2015-01-20 7:44 ` Anatolij Gustschin
2015-01-20 7:42 ` Anatolij Gustschin
1 sibling, 1 reply; 55+ messages in thread
From: Simon Glass @ 2015-01-20 0:33 UTC (permalink / raw)
To: u-boot
Hi Anatolij,
On 1 January 2015 at 16:17, Simon Glass <sjg@chromium.org> wrote:
> Some machines are very slow to scroll their displays. To cope with this,
> support the CONFIG_CONSOLE_SCROLL_LINES option. Setting this to 5 allows
> the display to operate at an acceptable speed by scrolling 5 lines at
> a time.
>
> This same option is available for LCDs so when these systems are unified
> this code can be unified also.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
Are you happy with this patch? If so, is it OK for me to pick it up via x86?
> ---
>
> Changes in v2: None
>
> drivers/video/cfb_console.c | 26 +++++++++++++++++---------
> 1 file changed, 17 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/video/cfb_console.c b/drivers/video/cfb_console.c
> index a653bb4..75cdf61 100644
> --- a/drivers/video/cfb_console.c
> +++ b/drivers/video/cfb_console.c
> @@ -312,7 +312,11 @@ void console_cursor(int state);
> #define CONSOLE_ROW_SECOND (video_console_address + CONSOLE_ROW_SIZE)
> #define CONSOLE_ROW_LAST (video_console_address + CONSOLE_SIZE - CONSOLE_ROW_SIZE)
> #define CONSOLE_SIZE (CONSOLE_ROW_SIZE * CONSOLE_ROWS)
> -#define CONSOLE_SCROLL_SIZE (CONSOLE_SIZE - CONSOLE_ROW_SIZE)
> +
> +/* By default we scroll by a single line */
> +#ifndef CONFIG_CONSOLE_SCROLL_LINES
> +#define CONFIG_CONSOLE_SCROLL_LINES 1
> +#endif
>
> /* Macros */
> #ifdef VIDEO_FB_LITTLE_ENDIAN
> @@ -753,26 +757,33 @@ static void console_clear_line(int line, int begin, int end)
>
> static void console_scrollup(void)
> {
> + const int rows = CONFIG_CONSOLE_SCROLL_LINES;
> + int i;
> +
> /* copy up rows ignoring the first one */
>
> #ifdef VIDEO_HW_BITBLT
> video_hw_bitblt(VIDEO_PIXEL_SIZE, /* bytes per pixel */
> 0, /* source pos x */
> video_logo_height +
> - VIDEO_FONT_HEIGHT, /* source pos y */
> + VIDEO_FONT_HEIGHT * rows, /* source pos y */
> 0, /* dest pos x */
> video_logo_height, /* dest pos y */
> VIDEO_VISIBLE_COLS, /* frame width */
> VIDEO_VISIBLE_ROWS
> - video_logo_height
> - - VIDEO_FONT_HEIGHT /* frame height */
> + - VIDEO_FONT_HEIGHT * rows /* frame height */
> );
> #else
> - memcpyl(CONSOLE_ROW_FIRST, CONSOLE_ROW_SECOND,
> - CONSOLE_SCROLL_SIZE >> 2);
> + memcpyl(CONSOLE_ROW_FIRST, CONSOLE_ROW_FIRST + rows * CONSOLE_ROW_SIZE,
> + (CONSOLE_SIZE - CONSOLE_ROW_SIZE * rows) >> 2);
> #endif
> /* clear the last one */
> - console_clear_line(CONSOLE_ROWS - 1, 0, CONSOLE_COLS - 1);
> + for (i = 1; i <= rows; i++)
> + console_clear_line(CONSOLE_ROWS - i, 0, CONSOLE_COLS - 1);
> +
> + /* Decrement row number */
> + console_row -= rows;
> }
>
> static void console_back(void)
> @@ -884,9 +895,6 @@ static void console_newline(int n)
> if (console_row >= CONSOLE_ROWS) {
> /* Scroll everything up */
> console_scrollup();
> -
> - /* Decrement row number */
> - console_row = CONSOLE_ROWS - 1;
> }
> }
>
> --
> 2.2.0.rc0.207.ga3a616c
>
Regards,
Simon
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES
2015-01-01 23:17 ` [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES Simon Glass
2015-01-20 0:33 ` Simon Glass
@ 2015-01-20 7:42 ` Anatolij Gustschin
1 sibling, 0 replies; 55+ messages in thread
From: Anatolij Gustschin @ 2015-01-20 7:42 UTC (permalink / raw)
To: u-boot
On Thu, 1 Jan 2015 16:17:57 -0700
Simon Glass <sjg@chromium.org> wrote:
> Some machines are very slow to scroll their displays. To cope with this,
> support the CONFIG_CONSOLE_SCROLL_LINES option. Setting this to 5 allows
> the display to operate at an acceptable speed by scrolling 5 lines at
> a time.
>
> This same option is available for LCDs so when these systems are unified
> this code can be unified also.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> drivers/video/cfb_console.c | 26 +++++++++++++++++---------
> 1 file changed, 17 insertions(+), 9 deletions(-)
Acked-by: Anatolij Gustschin <agust@denx.de>
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES
2015-01-20 0:33 ` Simon Glass
@ 2015-01-20 7:44 ` Anatolij Gustschin
2015-01-23 23:55 ` Simon Glass
0 siblings, 1 reply; 55+ messages in thread
From: Anatolij Gustschin @ 2015-01-20 7:44 UTC (permalink / raw)
To: u-boot
Hi Simon,
On Mon, 19 Jan 2015 17:33:08 -0700
Simon Glass <sjg@chromium.org> wrote:
> Hi Anatolij,
>
> On 1 January 2015 at 16:17, Simon Glass <sjg@chromium.org> wrote:
> > Some machines are very slow to scroll their displays. To cope with this,
> > support the CONFIG_CONSOLE_SCROLL_LINES option. Setting this to 5 allows
> > the display to operate at an acceptable speed by scrolling 5 lines at
> > a time.
> >
> > This same option is available for LCDs so when these systems are unified
> > this code can be unified also.
> >
> > Signed-off-by: Simon Glass <sjg@chromium.org>
>
> Are you happy with this patch? If so, is it OK for me to pick it up via x86?
yes, it is OK for me.
Thanks,
Anatolij
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES
2015-01-20 7:44 ` Anatolij Gustschin
@ 2015-01-23 23:55 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-23 23:55 UTC (permalink / raw)
To: u-boot
On 20 January 2015 at 00:44, Anatolij Gustschin <agust@denx.de> wrote:
> Hi Simon,
>
> On Mon, 19 Jan 2015 17:33:08 -0700
> Simon Glass <sjg@chromium.org> wrote:
>
>> Hi Anatolij,
>>
>> On 1 January 2015 at 16:17, Simon Glass <sjg@chromium.org> wrote:
>> > Some machines are very slow to scroll their displays. To cope with this,
>> > support the CONFIG_CONSOLE_SCROLL_LINES option. Setting this to 5 allows
>> > the display to operate at an acceptable speed by scrolling 5 lines at
>> > a time.
>> >
>> > This same option is available for LCDs so when these systems are unified
>> > this code can be unified also.
>> >
>> > Signed-off-by: Simon Glass <sjg@chromium.org>
>>
>> Are you happy with this patch? If so, is it OK for me to pick it up via x86?
>
> yes, it is OK for me.
Thanks.
Applied to u-boot-x86.
^ permalink raw reply [flat|nested] 55+ messages in thread
* [U-Boot] [PATCH v2 05/22] x86: config: Always scroll the display by 5 lines, for speed
2015-01-01 23:17 ` [U-Boot] [PATCH v2 05/22] x86: config: Always scroll the display by 5 lines, for speed Simon Glass
@ 2015-01-23 23:55 ` Simon Glass
0 siblings, 0 replies; 55+ messages in thread
From: Simon Glass @ 2015-01-23 23:55 UTC (permalink / raw)
To: u-boot
On 1 January 2015 at 16:17, Simon Glass <sjg@chromium.org> wrote:
> Scrolling a line at a time is very slow for reasons that I don't understand.
> It seems to take about 100ms to copy 4MB of RAM in the frame buffer. To cope
> with this, scroll 5 lines each time.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v2: None
>
> include/configs/x86-common.h | 1 +
> 1 file changed, 1 insertion(+)
Applied to u-boot-x86.
^ permalink raw reply [flat|nested] 55+ messages in thread
end of thread, other threads:[~2015-01-23 23:55 UTC | newest]
Thread overview: 55+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-01-01 23:17 [U-Boot] [PATCH v2 0/22] x86: Add support for MTRRs Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 01/22] x86: Correct XIP_ROM_SIZE Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 02/22] x86: Drop RAMTOP Kconfig Simon Glass
2015-01-04 2:26 ` Bin Meng
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 03/22] x86: Correct ifdtool microcode calculation Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 04/22] x86: video: Add support for CONFIG_CONSOLE_SCROLL_LINES Simon Glass
2015-01-20 0:33 ` Simon Glass
2015-01-20 7:44 ` Anatolij Gustschin
2015-01-23 23:55 ` Simon Glass
2015-01-20 7:42 ` Anatolij Gustschin
2015-01-01 23:17 ` [U-Boot] [PATCH v2 05/22] x86: config: Always scroll the display by 5 lines, for speed Simon Glass
2015-01-23 23:55 ` Simon Glass
2015-01-01 23:17 ` [U-Boot] [PATCH v2 06/22] x86: video: Add a debug() to display the frame buffer address Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 07/22] x86: pci: Don't return a vesa mode when there is not video Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 08/22] x86: video: Add debug option to time the BIOS copy Simon Glass
2015-01-05 17:39 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 09/22] x86: ivybridge: Only run the Video BIOS when video is enabled Simon Glass
2015-01-04 2:31 ` Bin Meng
2015-01-05 17:40 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 10/22] x86: Use cache, don't clear the display in video BIOS Simon Glass
2015-01-05 17:40 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 11/22] x86: Tidy up VESA mode numbers Simon Glass
2015-01-05 17:40 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 12/22] x86: pci: Display vesa modes in hex Simon Glass
2015-01-05 17:40 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 13/22] x86: ivybridge: Drop support for ROM caching Simon Glass
2015-01-05 17:40 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 14/22] x86: Add support for MTRRs Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 15/22] x86: ivybridge: Set up an MTRR for the video frame buffer Simon Glass
2015-01-04 3:18 ` Bin Meng
2015-01-04 3:20 ` Simon Glass
2015-01-04 3:28 ` Bin Meng
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 16/22] x86: board_f: Adjust x86 boot order for performance Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 17/22] x86: ivybridge: Request MTRRs for DRAM regions Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 18/22] x86: Commit the current MTRRs before relocation Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 19/22] x86: ivybridge: Add a way to turn off the CAR Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 20/22] x86: Disable CAR before relocation on platforms that need it Simon Glass
2015-01-04 3:53 ` Bin Meng
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 21/22] x86: ivybridge: Update microcode early in boot Simon Glass
2015-01-05 17:41 ` Simon Glass
2015-01-01 23:18 ` [U-Boot] [PATCH v2 22/22] x86: Add an 'mtrr' command to list and adjust MTRRs Simon Glass
2015-01-04 4:13 ` Bin Meng
2015-01-05 17:41 ` Simon Glass
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.