* [PATCH 1/4] ARM: dts: Move most of am335x-boneblack.dts to am335x-boneblack-common.dtsi
@ 2016-12-27 17:58 ` Robert Nelson
0 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 17:58 UTC (permalink / raw)
To: tony-4v6yS6AI5VpBDgjK7y7TUQ
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Robert Nelson,
Jason Kridner
This is going to be shared with the BeagleBone Black Wireless
Signed-off-by: Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
CC: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
CC: Jason Kridner <jkridner-hcmAuCOw+vXj4SYmN/TMmA@public.gmane.org>
---
arch/arm/boot/dts/am335x-boneblack-common.dtsi | 163 +++++++++++++++++++++++++
arch/arm/boot/dts/am335x-boneblack.dts | 155 +----------------------
2 files changed, 164 insertions(+), 154 deletions(-)
create mode 100644 arch/arm/boot/dts/am335x-boneblack-common.dtsi
diff --git a/arch/arm/boot/dts/am335x-boneblack-common.dtsi b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
new file mode 100644
index 000000000000..325daae40278
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
@@ -0,0 +1,163 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/display/tda998x.h>
+
+&ldo3_reg {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+ vmmc-supply = <&vmmcsd_fixed>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&am33xx_pinmux {
+ nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
+ AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
+ AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
+ AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
+ AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
+ AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
+ AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
+ AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
+ AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
+ AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
+ AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
+ AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
+ AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
+ AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
+ AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
+ AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
+ AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
+ AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
+ AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
+ AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
+ AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
+ >;
+ };
+
+ nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
+ >;
+ };
+
+ mcasp0_pins: mcasp0_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
+ AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
+ AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
+ AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
+ AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */
+ >;
+ };
+};
+
+&lcdc {
+ status = "okay";
+
+ /* If you want to get 24 bit RGB and 16 BGR mode instead of
+ * current 16 bit RGB and 24 BGR modes, set the propety
+ * below to "crossed" and uncomment the video-ports -property
+ * in tda19988 node.
+ */
+ blue-and-red-wiring = "straight";
+
+ port {
+ lcdc_0: endpoint@0 {
+ remote-endpoint = <&hdmi_0>;
+ };
+ };
+};
+
+&i2c0 {
+ tda19988: tda19988 {
+ compatible = "nxp,tda998x";
+ reg = <0x70>;
+
+ pinctrl-names = "default", "off";
+ pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+ pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+
+ /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
+ /* video-ports = <0x234501>; */
+
+ #sound-dai-cells = <0>;
+ audio-ports = < TDA998x_I2S 0x03>;
+
+ ports {
+ port@0 {
+ hdmi_0: endpoint@0 {
+ remote-endpoint = <&lcdc_0>;
+ };
+ };
+ };
+ };
+};
+
+&rtc {
+ system-power-controller;
+};
+
+&mcasp0 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcasp0_pins>;
+ status = "okay";
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+/ {
+ clk_mcasp0_fixed: clk_mcasp0_fixed {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24576000>;
+ };
+
+ clk_mcasp0: clk_mcasp0 {
+ #clock-cells = <0>;
+ compatible = "gpio-gate-clock";
+ clocks = <&clk_mcasp0_fixed>;
+ enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "TI BeagleBone Black";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&dailink0_master>;
+ simple-audio-card,frame-master = <&dailink0_master>;
+
+ dailink0_master: simple-audio-card,cpu {
+ sound-dai = <&mcasp0>;
+ clocks = <&clk_mcasp0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&tda19988>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index db00d8ef7b19..77273df1a028 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -9,162 +9,9 @@
#include "am33xx.dtsi"
#include "am335x-bone-common.dtsi"
-#include <dt-bindings/display/tda998x.h>
+#include "am335x-boneblack-common.dtsi"
/ {
model = "TI AM335x BeagleBone Black";
compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
};
-
-&ldo3_reg {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
-};
-
-&mmc1 {
- vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
- vmmc-supply = <&vmmcsd_fixed>;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_pins>;
- bus-width = <8>;
- status = "okay";
-};
-
-&am33xx_pinmux {
- nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
- AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
- AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
- AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
- AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
- AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
- AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
- AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
- AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
- AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
- AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
- AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
- AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
- AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
- AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
- AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
- AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
- AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
- AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
- AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
- AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
- >;
- };
- nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
- >;
- };
-
- mcasp0_pins: mcasp0_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
- AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
- AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
- AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
- AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */
- >;
- };
-};
-
-&lcdc {
- status = "okay";
-
- /* If you want to get 24 bit RGB and 16 BGR mode instead of
- * current 16 bit RGB and 24 BGR modes, set the propety
- * below to "crossed" and uncomment the video-ports -property
- * in tda19988 node.
- */
- blue-and-red-wiring = "straight";
-
- port {
- lcdc_0: endpoint@0 {
- remote-endpoint = <&hdmi_0>;
- };
- };
-};
-
-&i2c0 {
- tda19988: tda19988 {
- compatible = "nxp,tda998x";
- reg = <0x70>;
-
- pinctrl-names = "default", "off";
- pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
- pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
-
- /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
- /* video-ports = <0x234501>; */
-
- #sound-dai-cells = <0>;
- audio-ports = < TDA998x_I2S 0x03>;
-
- ports {
- port@0 {
- hdmi_0: endpoint@0 {
- remote-endpoint = <&lcdc_0>;
- };
- };
- };
- };
-};
-
-&rtc {
- system-power-controller;
-};
-
-&mcasp0 {
- #sound-dai-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mcasp0_pins>;
- status = "okay";
- op-mode = <0>; /* MCASP_IIS_MODE */
- tdm-slots = <2>;
- serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
- 0 0 1 0
- >;
- tx-num-evt = <32>;
- rx-num-evt = <32>;
-};
-
-/ {
- clk_mcasp0_fixed: clk_mcasp0_fixed {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24576000>;
- };
-
- clk_mcasp0: clk_mcasp0 {
- #clock-cells = <0>;
- compatible = "gpio-gate-clock";
- clocks = <&clk_mcasp0_fixed>;
- enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
- };
-
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "TI BeagleBone Black";
- simple-audio-card,format = "i2s";
- simple-audio-card,bitclock-master = <&dailink0_master>;
- simple-audio-card,frame-master = <&dailink0_master>;
-
- dailink0_master: simple-audio-card,cpu {
- sound-dai = <&mcasp0>;
- clocks = <&clk_mcasp0>;
- };
-
- simple-audio-card,codec {
- sound-dai = <&tda19988>;
- };
- };
-};
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 1/4] ARM: dts: Move most of am335x-boneblack.dts to am335x-boneblack-common.dtsi
@ 2016-12-27 17:58 ` Robert Nelson
0 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 17:58 UTC (permalink / raw)
To: linux-arm-kernel
This is going to be shared with the BeagleBone Black Wireless
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
---
arch/arm/boot/dts/am335x-boneblack-common.dtsi | 163 +++++++++++++++++++++++++
arch/arm/boot/dts/am335x-boneblack.dts | 155 +----------------------
2 files changed, 164 insertions(+), 154 deletions(-)
create mode 100644 arch/arm/boot/dts/am335x-boneblack-common.dtsi
diff --git a/arch/arm/boot/dts/am335x-boneblack-common.dtsi b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
new file mode 100644
index 000000000000..325daae40278
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
@@ -0,0 +1,163 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/display/tda998x.h>
+
+&ldo3_reg {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+ vmmc-supply = <&vmmcsd_fixed>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&am33xx_pinmux {
+ nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
+ AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
+ AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
+ AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
+ AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
+ AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
+ AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
+ AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
+ AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
+ AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
+ AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
+ AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
+ AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
+ AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
+ AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
+ AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
+ AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
+ AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
+ AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
+ AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
+ AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
+ >;
+ };
+
+ nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
+ >;
+ };
+
+ mcasp0_pins: mcasp0_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
+ AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
+ AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
+ AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
+ AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */
+ >;
+ };
+};
+
+&lcdc {
+ status = "okay";
+
+ /* If you want to get 24 bit RGB and 16 BGR mode instead of
+ * current 16 bit RGB and 24 BGR modes, set the propety
+ * below to "crossed" and uncomment the video-ports -property
+ * in tda19988 node.
+ */
+ blue-and-red-wiring = "straight";
+
+ port {
+ lcdc_0: endpoint at 0 {
+ remote-endpoint = <&hdmi_0>;
+ };
+ };
+};
+
+&i2c0 {
+ tda19988: tda19988 {
+ compatible = "nxp,tda998x";
+ reg = <0x70>;
+
+ pinctrl-names = "default", "off";
+ pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+ pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+
+ /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
+ /* video-ports = <0x234501>; */
+
+ #sound-dai-cells = <0>;
+ audio-ports = < TDA998x_I2S 0x03>;
+
+ ports {
+ port at 0 {
+ hdmi_0: endpoint at 0 {
+ remote-endpoint = <&lcdc_0>;
+ };
+ };
+ };
+ };
+};
+
+&rtc {
+ system-power-controller;
+};
+
+&mcasp0 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcasp0_pins>;
+ status = "okay";
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+/ {
+ clk_mcasp0_fixed: clk_mcasp0_fixed {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24576000>;
+ };
+
+ clk_mcasp0: clk_mcasp0 {
+ #clock-cells = <0>;
+ compatible = "gpio-gate-clock";
+ clocks = <&clk_mcasp0_fixed>;
+ enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "TI BeagleBone Black";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&dailink0_master>;
+ simple-audio-card,frame-master = <&dailink0_master>;
+
+ dailink0_master: simple-audio-card,cpu {
+ sound-dai = <&mcasp0>;
+ clocks = <&clk_mcasp0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&tda19988>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index db00d8ef7b19..77273df1a028 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -9,162 +9,9 @@
#include "am33xx.dtsi"
#include "am335x-bone-common.dtsi"
-#include <dt-bindings/display/tda998x.h>
+#include "am335x-boneblack-common.dtsi"
/ {
model = "TI AM335x BeagleBone Black";
compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
};
-
-&ldo3_reg {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
-};
-
-&mmc1 {
- vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
- vmmc-supply = <&vmmcsd_fixed>;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_pins>;
- bus-width = <8>;
- status = "okay";
-};
-
-&am33xx_pinmux {
- nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
- AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
- AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
- AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
- AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
- AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
- AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
- AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
- AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
- AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
- AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
- AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
- AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
- AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
- AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
- AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
- AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
- AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
- AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
- AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
- AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
- >;
- };
- nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
- >;
- };
-
- mcasp0_pins: mcasp0_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
- AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
- AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
- AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
- AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */
- >;
- };
-};
-
-&lcdc {
- status = "okay";
-
- /* If you want to get 24 bit RGB and 16 BGR mode instead of
- * current 16 bit RGB and 24 BGR modes, set the propety
- * below to "crossed" and uncomment the video-ports -property
- * in tda19988 node.
- */
- blue-and-red-wiring = "straight";
-
- port {
- lcdc_0: endpoint at 0 {
- remote-endpoint = <&hdmi_0>;
- };
- };
-};
-
-&i2c0 {
- tda19988: tda19988 {
- compatible = "nxp,tda998x";
- reg = <0x70>;
-
- pinctrl-names = "default", "off";
- pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
- pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
-
- /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
- /* video-ports = <0x234501>; */
-
- #sound-dai-cells = <0>;
- audio-ports = < TDA998x_I2S 0x03>;
-
- ports {
- port at 0 {
- hdmi_0: endpoint at 0 {
- remote-endpoint = <&lcdc_0>;
- };
- };
- };
- };
-};
-
-&rtc {
- system-power-controller;
-};
-
-&mcasp0 {
- #sound-dai-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mcasp0_pins>;
- status = "okay";
- op-mode = <0>; /* MCASP_IIS_MODE */
- tdm-slots = <2>;
- serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
- 0 0 1 0
- >;
- tx-num-evt = <32>;
- rx-num-evt = <32>;
-};
-
-/ {
- clk_mcasp0_fixed: clk_mcasp0_fixed {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24576000>;
- };
-
- clk_mcasp0: clk_mcasp0 {
- #clock-cells = <0>;
- compatible = "gpio-gate-clock";
- clocks = <&clk_mcasp0_fixed>;
- enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
- };
-
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "TI BeagleBone Black";
- simple-audio-card,format = "i2s";
- simple-audio-card,bitclock-master = <&dailink0_master>;
- simple-audio-card,frame-master = <&dailink0_master>;
-
- dailink0_master: simple-audio-card,cpu {
- sound-dai = <&mcasp0>;
- clocks = <&clk_mcasp0>;
- };
-
- simple-audio-card,codec {
- sound-dai = <&tda19988>;
- };
- };
-};
--
2.11.0
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
2016-12-27 17:58 ` Robert Nelson
@ 2016-12-27 17:58 ` Robert Nelson
-1 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 17:58 UTC (permalink / raw)
To: tony-4v6yS6AI5VpBDgjK7y7TUQ
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Robert Nelson,
Jason Kridner
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
replaced by a TI wl1835 wireless module.
This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
http://beagleboard.org/black-wireless
https://github.com/beagleboard/beaglebone-black-wireless
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
CC: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
CC: Jason Kridner <jkridner-hcmAuCOw+vXj4SYmN/TMmA@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-boneblack-wireless.dts | 109 ++++++++++++++++++++++++
2 files changed, 110 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-boneblack-wireless.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cccdbcb557b6..9415a49bd11b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -563,6 +563,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-base0033.dtb \
am335x-bone.dtb \
am335x-boneblack.dtb \
+ am335x-boneblack-wireless.dtb \
am335x-bonegreen.dtb \
am335x-chiliboard.dtb \
am335x-cm-t335.dtb \
diff --git a/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
new file mode 100644
index 000000000000..105bd10655f7
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
@@ -0,0 +1,109 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "TI AM335x BeagleBone Black Wireless";
+ compatible = "ti,am335x-bone-black-wireless", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+ wlan_en_reg: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us= <70000>;
+
+ /* WL_EN */
+ gpio = <&gpio3 9 0>;
+ enable-active-high;
+ };
+};
+
+&am33xx_pinmux {
+ bt_pins: pinmux_bt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_txd0.gpio0_28 - BT_EN */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */
+ AM33XX_IOPAD(0x914, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */
+ AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */
+ AM33XX_IOPAD(0x91c, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */
+ AM33XX_IOPAD(0x920, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */
+ AM33XX_IOPAD(0x908, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* gmii1_rxd3.uart3_rxd */
+ AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gmii1_rxd2.uart3_txd */
+ AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3) /* mdio_data.uart3_ctsn */
+ AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* mdio_clk.uart3_rtsn */
+ >;
+ };
+
+ wl18xx_pins: pinmux_wl18xx_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gmii1_txclk.gpio3_9 WL_EN */
+ AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk.gpio0_29 WL_IRQ */
+ AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_rxclk.gpio3_10 LS_BUF_EN */
+ >;
+ };
+};
+
+&mac {
+ status = "disabled";
+};
+
+&mmc3 {
+ dmas = <&edma_xbar 12 0 1
+ &edma_xbar 13 0 2>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ non-removable;
+ cap-power-off-card;
+ ti,needs-special-hs-handling;
+ keep-power-in-suspend;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins &bt_pins>;
+ status = "okay";
+};
+
+&gpio3 {
+ ls_buf_en {
+ gpio-hog;
+ gpios = <10 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "LS_BUF_EN";
+ };
+};
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2016-12-27 17:58 ` Robert Nelson
0 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 17:58 UTC (permalink / raw)
To: linux-arm-kernel
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
replaced by a TI wl1835 wireless module.
This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
http://beagleboard.org/black-wireless
https://github.com/beagleboard/beaglebone-black-wireless
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet at 4a100000/slave at 4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-boneblack-wireless.dts | 109 ++++++++++++++++++++++++
2 files changed, 110 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-boneblack-wireless.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cccdbcb557b6..9415a49bd11b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -563,6 +563,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-base0033.dtb \
am335x-bone.dtb \
am335x-boneblack.dtb \
+ am335x-boneblack-wireless.dtb \
am335x-bonegreen.dtb \
am335x-chiliboard.dtb \
am335x-cm-t335.dtb \
diff --git a/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
new file mode 100644
index 000000000000..105bd10655f7
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
@@ -0,0 +1,109 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "TI AM335x BeagleBone Black Wireless";
+ compatible = "ti,am335x-bone-black-wireless", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+ wlan_en_reg: fixedregulator at 2 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us= <70000>;
+
+ /* WL_EN */
+ gpio = <&gpio3 9 0>;
+ enable-active-high;
+ };
+};
+
+&am33xx_pinmux {
+ bt_pins: pinmux_bt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_txd0.gpio0_28 - BT_EN */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */
+ AM33XX_IOPAD(0x914, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */
+ AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */
+ AM33XX_IOPAD(0x91c, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */
+ AM33XX_IOPAD(0x920, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */
+ AM33XX_IOPAD(0x908, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* gmii1_rxd3.uart3_rxd */
+ AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gmii1_rxd2.uart3_txd */
+ AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3) /* mdio_data.uart3_ctsn */
+ AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* mdio_clk.uart3_rtsn */
+ >;
+ };
+
+ wl18xx_pins: pinmux_wl18xx_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gmii1_txclk.gpio3_9 WL_EN */
+ AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk.gpio0_29 WL_IRQ */
+ AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_rxclk.gpio3_10 LS_BUF_EN */
+ >;
+ };
+};
+
+&mac {
+ status = "disabled";
+};
+
+&mmc3 {
+ dmas = <&edma_xbar 12 0 1
+ &edma_xbar 13 0 2>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ non-removable;
+ cap-power-off-card;
+ ti,needs-special-hs-handling;
+ keep-power-in-suspend;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore at 2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins &bt_pins>;
+ status = "okay";
+};
+
+&gpio3 {
+ ls_buf_en {
+ gpio-hog;
+ gpios = <10 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "LS_BUF_EN";
+ };
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 3/4] ARM: dts: Move most of am335x-bonegreen.dts to am335x-bonegreen-common.dtsi
2016-12-27 17:58 ` Robert Nelson
@ 2016-12-27 17:58 ` Robert Nelson
-1 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 17:58 UTC (permalink / raw)
To: tony-4v6yS6AI5VpBDgjK7y7TUQ
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Robert Nelson,
Jason Kridner
This is going to be shared with the SeeedStudio BeagleBone Green Wireless
Signed-off-by: Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
CC: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
CC: Jason Kridner <jkridner-hcmAuCOw+vXj4SYmN/TMmA@public.gmane.org>
---
arch/arm/boot/dts/am335x-bonegreen-common.dtsi | 44 ++++++++++++++++++++++++++
arch/arm/boot/dts/am335x-bonegreen.dts | 38 +---------------------
2 files changed, 45 insertions(+), 37 deletions(-)
create mode 100644 arch/arm/boot/dts/am335x-bonegreen-common.dtsi
diff --git a/arch/arm/boot/dts/am335x-bonegreen-common.dtsi b/arch/arm/boot/dts/am335x-bonegreen-common.dtsi
new file mode 100644
index 000000000000..853e6d3a028d
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-bonegreen-common.dtsi
@@ -0,0 +1,44 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&ldo3_reg {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+ vmmc-supply = <&vmmcsd_fixed>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&am33xx_pinmux {
+ uart2_pins: uart2_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */
+ AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */
+ >;
+ };
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&rtc {
+ system-power-controller;
+};
diff --git a/arch/arm/boot/dts/am335x-bonegreen.dts b/arch/arm/boot/dts/am335x-bonegreen.dts
index dce3c8657e04..a8b4d969ce2a 100644
--- a/arch/arm/boot/dts/am335x-bonegreen.dts
+++ b/arch/arm/boot/dts/am335x-bonegreen.dts
@@ -9,45 +9,9 @@
#include "am33xx.dtsi"
#include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
/ {
model = "TI AM335x BeagleBone Green";
compatible = "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
};
-
-&ldo3_reg {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
-};
-
-&mmc1 {
- vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
- vmmc-supply = <&vmmcsd_fixed>;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_pins>;
- bus-width = <8>;
- status = "okay";
-};
-
-&am33xx_pinmux {
- uart2_pins: uart2_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */
- AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */
- >;
- };
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins>;
- status = "okay";
-};
-
-&rtc {
- system-power-controller;
-};
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 3/4] ARM: dts: Move most of am335x-bonegreen.dts to am335x-bonegreen-common.dtsi
@ 2016-12-27 17:58 ` Robert Nelson
0 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 17:58 UTC (permalink / raw)
To: linux-arm-kernel
This is going to be shared with the SeeedStudio BeagleBone Green Wireless
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
---
arch/arm/boot/dts/am335x-bonegreen-common.dtsi | 44 ++++++++++++++++++++++++++
arch/arm/boot/dts/am335x-bonegreen.dts | 38 +---------------------
2 files changed, 45 insertions(+), 37 deletions(-)
create mode 100644 arch/arm/boot/dts/am335x-bonegreen-common.dtsi
diff --git a/arch/arm/boot/dts/am335x-bonegreen-common.dtsi b/arch/arm/boot/dts/am335x-bonegreen-common.dtsi
new file mode 100644
index 000000000000..853e6d3a028d
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-bonegreen-common.dtsi
@@ -0,0 +1,44 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&ldo3_reg {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+ vmmc-supply = <&vmmcsd_fixed>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&am33xx_pinmux {
+ uart2_pins: uart2_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */
+ AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */
+ >;
+ };
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&rtc {
+ system-power-controller;
+};
diff --git a/arch/arm/boot/dts/am335x-bonegreen.dts b/arch/arm/boot/dts/am335x-bonegreen.dts
index dce3c8657e04..a8b4d969ce2a 100644
--- a/arch/arm/boot/dts/am335x-bonegreen.dts
+++ b/arch/arm/boot/dts/am335x-bonegreen.dts
@@ -9,45 +9,9 @@
#include "am33xx.dtsi"
#include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
/ {
model = "TI AM335x BeagleBone Green";
compatible = "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
};
-
-&ldo3_reg {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
-};
-
-&mmc1 {
- vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
- vmmc-supply = <&vmmcsd_fixed>;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_pins>;
- bus-width = <8>;
- status = "okay";
-};
-
-&am33xx_pinmux {
- uart2_pins: uart2_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */
- AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */
- >;
- };
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins>;
- status = "okay";
-};
-
-&rtc {
- system-power-controller;
-};
--
2.11.0
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 4/4] ARM: dts: Add am335x-bonegreen-wireless
2016-12-27 17:58 ` Robert Nelson
@ 2016-12-27 17:58 ` Robert Nelson
-1 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 17:58 UTC (permalink / raw)
To: tony-4v6yS6AI5VpBDgjK7y7TUQ
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Robert Nelson,
Jason Kridner
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the SeeedStudio
Green (BBG) with the Ethernet replaced by a TI wl1835 wireless module.
This board can be indentified by the GW1x value after A335BNLT (BBB) in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|]
http://beagleboard.org/green-wireless
http://wiki.seeed.cc/BeagleBone_Green_Wireless/
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16
Signed-off-by: Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
CC: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
CC: Jason Kridner <jkridner-hcmAuCOw+vXj4SYmN/TMmA@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-bonegreen-wireless.dts | 126 ++++++++++++++++++++++++
2 files changed, 127 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-bonegreen-wireless.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9415a49bd11b..6c0a3e3fdf30 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -565,6 +565,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-boneblack.dtb \
am335x-boneblack-wireless.dtb \
am335x-bonegreen.dtb \
+ am335x-bonegreen-wireless.dtb \
am335x-chiliboard.dtb \
am335x-cm-t335.dtb \
am335x-evm.dtb \
diff --git a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
new file mode 100644
index 000000000000..9d1a0fd555f3
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "TI AM335x BeagleBone Green Wireless";
+ compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+ wlan_en_reg: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us= <70000>;
+
+ /* WL_EN */
+ gpio = <&gpio0 26 0>;
+ enable-active-high;
+ };
+};
+
+&am33xx_pinmux {
+ bt_pins: pinmux_bt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x878, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_ad12.gpio1_28 BT_EN */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad12.mmc2_dat0 */
+ AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad13.mmc2_dat1 */
+ AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad14.mmc2_dat2 */
+ AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad15.mmc2_dat3 */
+ AM33XX_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd */
+ AM33XX_IOPAD(0x88c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* gmii1_rxd3.uart3_rxd */
+ AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gmii1_rxd2.uart3_txd */
+ AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3) /* mdio_data.uart3_ctsn */
+ AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* mdio_clk.uart3_rtsn */
+ >;
+ };
+
+ wl18xx_pins: pinmux_wl18xx_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x828, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.gpio0_26 WL_EN */
+ AM33XX_IOPAD(0x82C, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.gpio0_27 WL_IRQ */
+ AM33XX_IOPAD(0x87C, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 LS_BUF_EN */
+ >;
+ };
+};
+
+&mac {
+ status = "disabled";
+};
+
+&mmc3 {
+ dmas = <&edma_xbar 12 0 1
+ &edma_xbar 13 0 2>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ non-removable;
+ cap-power-off-card;
+ ti,needs-special-hs-handling;
+ keep-power-in-suspend;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins &bt_pins>;
+ status = "okay";
+};
+
+&gpio1 {
+ ls_buf_en {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "LS_BUF_EN";
+ };
+};
+
+/* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/
+/* in case it isn't, wilink8 ends up in one of the test modes that */
+/* intruces various issues (elp wkaeup timeouts etc.) */
+/* On the BBGW this pin is routed through the level shifter (U21) that */
+/* introduces a pullup on the line and wilink8 ends up in a bad state. */
+/* use a gpio hog to force this pin low. An alternative may be adding */
+/* an external pulldown on U21 pin 4. */
+
+&gpio3 {
+ bt_aud_in {
+ gpio-hog;
+ gpios = <16 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "MCASP0_AHCLKR";
+ };
+};
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 4/4] ARM: dts: Add am335x-bonegreen-wireless
@ 2016-12-27 17:58 ` Robert Nelson
0 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 17:58 UTC (permalink / raw)
To: linux-arm-kernel
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the SeeedStudio
Green (BBG) with the Ethernet replaced by a TI wl1835 wireless module.
This board can be indentified by the GW1x value after A335BNLT (BBB) in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|]
http://beagleboard.org/green-wireless
http://wiki.seeed.cc/BeagleBone_Green_Wireless/
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-bonegreen-wireless.dts | 126 ++++++++++++++++++++++++
2 files changed, 127 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-bonegreen-wireless.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9415a49bd11b..6c0a3e3fdf30 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -565,6 +565,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-boneblack.dtb \
am335x-boneblack-wireless.dtb \
am335x-bonegreen.dtb \
+ am335x-bonegreen-wireless.dtb \
am335x-chiliboard.dtb \
am335x-cm-t335.dtb \
am335x-evm.dtb \
diff --git a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
new file mode 100644
index 000000000000..9d1a0fd555f3
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "TI AM335x BeagleBone Green Wireless";
+ compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+ wlan_en_reg: fixedregulator at 2 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us= <70000>;
+
+ /* WL_EN */
+ gpio = <&gpio0 26 0>;
+ enable-active-high;
+ };
+};
+
+&am33xx_pinmux {
+ bt_pins: pinmux_bt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x878, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_ad12.gpio1_28 BT_EN */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad12.mmc2_dat0 */
+ AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad13.mmc2_dat1 */
+ AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad14.mmc2_dat2 */
+ AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad15.mmc2_dat3 */
+ AM33XX_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd */
+ AM33XX_IOPAD(0x88c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* gmii1_rxd3.uart3_rxd */
+ AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gmii1_rxd2.uart3_txd */
+ AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3) /* mdio_data.uart3_ctsn */
+ AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* mdio_clk.uart3_rtsn */
+ >;
+ };
+
+ wl18xx_pins: pinmux_wl18xx_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x828, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.gpio0_26 WL_EN */
+ AM33XX_IOPAD(0x82C, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.gpio0_27 WL_IRQ */
+ AM33XX_IOPAD(0x87C, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 LS_BUF_EN */
+ >;
+ };
+};
+
+&mac {
+ status = "disabled";
+};
+
+&mmc3 {
+ dmas = <&edma_xbar 12 0 1
+ &edma_xbar 13 0 2>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ non-removable;
+ cap-power-off-card;
+ ti,needs-special-hs-handling;
+ keep-power-in-suspend;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore at 2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins &bt_pins>;
+ status = "okay";
+};
+
+&gpio1 {
+ ls_buf_en {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "LS_BUF_EN";
+ };
+};
+
+/* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/
+/* in case it isn't, wilink8 ends up in one of the test modes that */
+/* intruces various issues (elp wkaeup timeouts etc.) */
+/* On the BBGW this pin is routed through the level shifter (U21) that */
+/* introduces a pullup on the line and wilink8 ends up in a bad state. */
+/* use a gpio hog to force this pin low. An alternative may be adding */
+/* an external pulldown on U21 pin 4. */
+
+&gpio3 {
+ bt_aud_in {
+ gpio-hog;
+ gpios = <16 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "MCASP0_AHCLKR";
+ };
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 26+ messages in thread
* Re: [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
2016-12-27 17:58 ` Robert Nelson
@ 2016-12-27 18:01 ` Robert Nelson
-1 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 18:01 UTC (permalink / raw)
To: tony-4v6yS6AI5VpBDgjK7y7TUQ
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA, devicetree,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Robert Nelson,
Jason Kridner
On Tue, Dec 27, 2016 at 11:58 AM, Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> replaced by a TI wl1835 wireless module.
>
> This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
>
> http://beagleboard.org/black-wireless
> https://github.com/beagleboard/beaglebone-black-wireless
>
> firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
Tony, this firmware should be there shortly, i have a pull request
setup for Jason:
https://github.com/beagleboard/beaglebone-black-wireless/pull/5
Regards,
--
Robert Nelson
https://rcn-ee.com/
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2016-12-27 18:01 ` Robert Nelson
0 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 18:01 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Dec 27, 2016 at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
> BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> replaced by a TI wl1835 wireless module.
>
> This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
>
> http://beagleboard.org/black-wireless
> https://github.com/beagleboard/beaglebone-black-wireless
>
> firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
Tony, this firmware should be there shortly, i have a pull request
setup for Jason:
https://github.com/beagleboard/beaglebone-black-wireless/pull/5
Regards,
--
Robert Nelson
https://rcn-ee.com/
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
2016-12-27 18:01 ` Robert Nelson
@ 2016-12-27 18:14 ` Tony Lindgren
-1 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2016-12-27 18:14 UTC (permalink / raw)
To: Robert Nelson
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA, devicetree,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Jason Kridner
* Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> [161227 10:02]:
> On Tue, Dec 27, 2016 at 11:58 AM, Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> > BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> > replaced by a TI wl1835 wireless module.
> >
> > This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> > BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
> >
> > http://beagleboard.org/black-wireless
> > https://github.com/beagleboard/beaglebone-black-wireless
> >
> > firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
>
> Tony, this firmware should be there shortly, i have a pull request
> setup for Jason:
>
> https://github.com/beagleboard/beaglebone-black-wireless/pull/5
OK great, good to have these working out of the box with mainline
kernel :)
Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2016-12-27 18:14 ` Tony Lindgren
0 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2016-12-27 18:14 UTC (permalink / raw)
To: linux-arm-kernel
* Robert Nelson <robertcnelson@gmail.com> [161227 10:02]:
> On Tue, Dec 27, 2016 at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
> > BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> > replaced by a TI wl1835 wireless module.
> >
> > This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> > BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
> >
> > http://beagleboard.org/black-wireless
> > https://github.com/beagleboard/beaglebone-black-wireless
> >
> > firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
>
> Tony, this firmware should be there shortly, i have a pull request
> setup for Jason:
>
> https://github.com/beagleboard/beaglebone-black-wireless/pull/5
OK great, good to have these working out of the box with mainline
kernel :)
Tony
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
2016-12-27 18:14 ` Tony Lindgren
@ 2016-12-27 18:56 ` Tony Lindgren
-1 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2016-12-27 18:56 UTC (permalink / raw)
To: Robert Nelson
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA, devicetree,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Jason Kridner
* Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org> [161227 10:15]:
> * Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> [161227 10:02]:
> > On Tue, Dec 27, 2016 at 11:58 AM, Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> > > BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> > > replaced by a TI wl1835 wireless module.
> > >
> > > This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> > > BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
> > >
> > > http://beagleboard.org/black-wireless
> > > https://github.com/beagleboard/beaglebone-black-wireless
> > >
> > > firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
> >
> > Tony, this firmware should be there shortly, i have a pull request
> > setup for Jason:
> >
> > https://github.com/beagleboard/beaglebone-black-wireless/pull/5
>
> OK great, good to have these working out of the box with mainline
> kernel :)
Hmm so is this firmware file also something that should really be generated
separately for each board? Or can the same one be used for all BBB black
wireless and green boards?
See the LKML thread "[PATCH 0/6] wl1251: Fix MAC address for Nokia N900",
at least with wl1251 the calibration has been done for each n900 device
during production.
Regards,
Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2016-12-27 18:56 ` Tony Lindgren
0 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2016-12-27 18:56 UTC (permalink / raw)
To: linux-arm-kernel
* Tony Lindgren <tony@atomide.com> [161227 10:15]:
> * Robert Nelson <robertcnelson@gmail.com> [161227 10:02]:
> > On Tue, Dec 27, 2016 at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
> > > BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> > > replaced by a TI wl1835 wireless module.
> > >
> > > This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> > > BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
> > >
> > > http://beagleboard.org/black-wireless
> > > https://github.com/beagleboard/beaglebone-black-wireless
> > >
> > > firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
> >
> > Tony, this firmware should be there shortly, i have a pull request
> > setup for Jason:
> >
> > https://github.com/beagleboard/beaglebone-black-wireless/pull/5
>
> OK great, good to have these working out of the box with mainline
> kernel :)
Hmm so is this firmware file also something that should really be generated
separately for each board? Or can the same one be used for all BBB black
wireless and green boards?
See the LKML thread "[PATCH 0/6] wl1251: Fix MAC address for Nokia N900",
at least with wl1251 the calibration has been done for each n900 device
during production.
Regards,
Tony
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
2016-12-27 18:56 ` Tony Lindgren
@ 2016-12-27 19:21 ` Robert Nelson
-1 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 19:21 UTC (permalink / raw)
To: Tony Lindgren; +Cc: devicetree, linux-omap, linux-arm-kernel, Jason Kridner
On Tue, Dec 27, 2016 at 12:56 PM, Tony Lindgren <tony@atomide.com> wrote:
> * Tony Lindgren <tony@atomide.com> [161227 10:15]:
>> * Robert Nelson <robertcnelson@gmail.com> [161227 10:02]:
>> > On Tue, Dec 27, 2016 at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
>> > > BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
>> > > replaced by a TI wl1835 wireless module.
>> > >
>> > > This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
>> > > BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
>> > >
>> > > http://beagleboard.org/black-wireless
>> > > https://github.com/beagleboard/beaglebone-black-wireless
>> > >
>> > > firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
>> >
>> > Tony, this firmware should be there shortly, i have a pull request
>> > setup for Jason:
>> >
>> > https://github.com/beagleboard/beaglebone-black-wireless/pull/5
>>
>> OK great, good to have these working out of the box with mainline
>> kernel :)
>
> Hmm so is this firmware file also something that should really be generated
> separately for each board? Or can the same one be used for all BBB black
> wireless and green boards?
>
> See the LKML thread "[PATCH 0/6] wl1251: Fix MAC address for Nokia N900",
> at least with wl1251 the calibration has been done for each n900 device
> during production.
>From what i can tell from TI, it should be good for all wl1835 modules
that use two wifi antenna's.
(that's the magic in: WL1835MOD_INI_C2PC.ini)
We are using the same wl18xx-conf.bin firmware for:
Original CircuitCo (now out of production) wl1835mod cape for BeagleBone Black
updated GateWay Cape from embest (this was meant to replace the wl1835mod cape)
SeeedStudio BeagleBone Green Wireless
BeagleBone Black Wireless
and the upcoming: (jason just sent me the next alpha, so i'll have a
patch after i verify all changes..)
BeagleBone Blue
For FCC testing, this was the same firmware (wl18xx-conf.bin) that
SeeedStudio used when they did the official FCC testing on the Green
Wireless. I believe GHI Electronics did the same with the BeagleBone
Black Wireless, but i wasn't CC'ed in that email conversation, so i
can't say with 100% certainty..
Regards,
--
Robert Nelson
https://rcn-ee.com/
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2016-12-27 19:21 ` Robert Nelson
0 siblings, 0 replies; 26+ messages in thread
From: Robert Nelson @ 2016-12-27 19:21 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Dec 27, 2016 at 12:56 PM, Tony Lindgren <tony@atomide.com> wrote:
> * Tony Lindgren <tony@atomide.com> [161227 10:15]:
>> * Robert Nelson <robertcnelson@gmail.com> [161227 10:02]:
>> > On Tue, Dec 27, 2016 at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
>> > > BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
>> > > replaced by a TI wl1835 wireless module.
>> > >
>> > > This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
>> > > BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
>> > >
>> > > http://beagleboard.org/black-wireless
>> > > https://github.com/beagleboard/beaglebone-black-wireless
>> > >
>> > > firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
>> >
>> > Tony, this firmware should be there shortly, i have a pull request
>> > setup for Jason:
>> >
>> > https://github.com/beagleboard/beaglebone-black-wireless/pull/5
>>
>> OK great, good to have these working out of the box with mainline
>> kernel :)
>
> Hmm so is this firmware file also something that should really be generated
> separately for each board? Or can the same one be used for all BBB black
> wireless and green boards?
>
> See the LKML thread "[PATCH 0/6] wl1251: Fix MAC address for Nokia N900",
> at least with wl1251 the calibration has been done for each n900 device
> during production.
>From what i can tell from TI, it should be good for all wl1835 modules
that use two wifi antenna's.
(that's the magic in: WL1835MOD_INI_C2PC.ini)
We are using the same wl18xx-conf.bin firmware for:
Original CircuitCo (now out of production) wl1835mod cape for BeagleBone Black
updated GateWay Cape from embest (this was meant to replace the wl1835mod cape)
SeeedStudio BeagleBone Green Wireless
BeagleBone Black Wireless
and the upcoming: (jason just sent me the next alpha, so i'll have a
patch after i verify all changes..)
BeagleBone Blue
For FCC testing, this was the same firmware (wl18xx-conf.bin) that
SeeedStudio used when they did the official FCC testing on the Green
Wireless. I believe GHI Electronics did the same with the BeagleBone
Black Wireless, but i wasn't CC'ed in that email conversation, so i
can't say with 100% certainty..
Regards,
--
Robert Nelson
https://rcn-ee.com/
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
2016-12-27 17:58 ` Robert Nelson
@ 2016-12-28 21:26 ` Jason Kridner
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Kridner @ 2016-12-28 21:26 UTC (permalink / raw)
To: Robert Nelson
Cc: tony-4v6yS6AI5VpBDgjK7y7TUQ, linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Jason Kridner
> On Dec 27, 2016, at 11:58 AM, Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>
> BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> replaced by a TI wl1835 wireless module.
>
> This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
I believe the correct statement is BWxx, but BWBx reserves the option to be software incompatible in some way. My preference is to have it boot anyway, but I believe that is only dependent in the bootloader.
>
> http://beagleboard.org/black-wireless
> https://github.com/beagleboard/beaglebone-black-wireless
>
> firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
> wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
>
> Signed-off-by: Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> CC: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
> CC: Jason Kridner <jkridner-hcmAuCOw+vXj4SYmN/TMmA@public.gmane.org>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/am335x-boneblack-wireless.dts | 109 ++++++++++++++++++++++++
> 2 files changed, 110 insertions(+)
> create mode 100644 arch/arm/boot/dts/am335x-boneblack-wireless.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index cccdbcb557b6..9415a49bd11b 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -563,6 +563,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
> am335x-base0033.dtb \
> am335x-bone.dtb \
> am335x-boneblack.dtb \
> + am335x-boneblack-wireless.dtb \
> am335x-bonegreen.dtb \
> am335x-chiliboard.dtb \
> am335x-cm-t335.dtb \
> diff --git a/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
> new file mode 100644
> index 000000000000..105bd10655f7
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
> @@ -0,0 +1,109 @@
> +/*
> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +/dts-v1/;
> +
> +#include "am33xx.dtsi"
> +#include "am335x-bone-common.dtsi"
> +#include "am335x-boneblack-common.dtsi"
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "TI AM335x BeagleBone Black Wireless";
> + compatible = "ti,am335x-bone-black-wireless", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
> +
> + wlan_en_reg: fixedregulator@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "wlan-en-regulator";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + startup-delay-us= <70000>;
> +
> + /* WL_EN */
> + gpio = <&gpio3 9 0>;
> + enable-active-high;
> + };
> +};
> +
> +&am33xx_pinmux {
> + bt_pins: pinmux_bt_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_txd0.gpio0_28 - BT_EN */
> + >;
> + };
> +
> + mmc3_pins: pinmux_mmc3_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */
> + AM33XX_IOPAD(0x914, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */
> + AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */
> + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */
> + AM33XX_IOPAD(0x920, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */
> + AM33XX_IOPAD(0x908, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */
> + >;
> + };
> +
> + uart3_pins: pinmux_uart3_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* gmii1_rxd3.uart3_rxd */
> + AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gmii1_rxd2.uart3_txd */
> + AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3) /* mdio_data.uart3_ctsn */
> + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* mdio_clk.uart3_rtsn */
> + >;
> + };
> +
> + wl18xx_pins: pinmux_wl18xx_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gmii1_txclk.gpio3_9 WL_EN */
> + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk.gpio0_29 WL_IRQ */
> + AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_rxclk.gpio3_10 LS_BUF_EN */
> + >;
> + };
> +};
> +
> +&mac {
> + status = "disabled";
> +};
> +
> +&mmc3 {
> + dmas = <&edma_xbar 12 0 1
> + &edma_xbar 13 0 2>;
> + dma-names = "tx", "rx";
> + status = "okay";
> + vmmc-supply = <&wlan_en_reg>;
> + bus-width = <4>;
> + non-removable;
> + cap-power-off-card;
> + ti,needs-special-hs-handling;
> + keep-power-in-suspend;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + wlcore: wlcore@2 {
> + compatible = "ti,wl1835";
> + reg = <2>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <29 IRQ_TYPE_EDGE_RISING>;
> + };
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart3_pins &bt_pins>;
> + status = "okay";
> +};
> +
> +&gpio3 {
> + ls_buf_en {
> + gpio-hog;
> + gpios = <10 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "LS_BUF_EN";
> + };
> +};
> --
> 2.11.0
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2016-12-28 21:26 ` Jason Kridner
0 siblings, 0 replies; 26+ messages in thread
From: Jason Kridner @ 2016-12-28 21:26 UTC (permalink / raw)
To: linux-arm-kernel
> On Dec 27, 2016, at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
>
> BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> replaced by a TI wl1835 wireless module.
>
> This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
I believe the correct statement is BWxx, but BWBx reserves the option to be software incompatible in some way. My preference is to have it boot anyway, but I believe that is only dependent in the bootloader.
>
> http://beagleboard.org/black-wireless
> https://github.com/beagleboard/beaglebone-black-wireless
>
> firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
> wl18xx mac address: /proc/device-tree/ocp/ethernet at 4a100000/slave at 4a100200/mac-address
>
> Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
> CC: Tony Lindgren <tony@atomide.com>
> CC: Jason Kridner <jkridner@beagleboard.org>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/am335x-boneblack-wireless.dts | 109 ++++++++++++++++++++++++
> 2 files changed, 110 insertions(+)
> create mode 100644 arch/arm/boot/dts/am335x-boneblack-wireless.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index cccdbcb557b6..9415a49bd11b 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -563,6 +563,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
> am335x-base0033.dtb \
> am335x-bone.dtb \
> am335x-boneblack.dtb \
> + am335x-boneblack-wireless.dtb \
> am335x-bonegreen.dtb \
> am335x-chiliboard.dtb \
> am335x-cm-t335.dtb \
> diff --git a/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
> new file mode 100644
> index 000000000000..105bd10655f7
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
> @@ -0,0 +1,109 @@
> +/*
> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +/dts-v1/;
> +
> +#include "am33xx.dtsi"
> +#include "am335x-bone-common.dtsi"
> +#include "am335x-boneblack-common.dtsi"
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "TI AM335x BeagleBone Black Wireless";
> + compatible = "ti,am335x-bone-black-wireless", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
> +
> + wlan_en_reg: fixedregulator at 2 {
> + compatible = "regulator-fixed";
> + regulator-name = "wlan-en-regulator";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + startup-delay-us= <70000>;
> +
> + /* WL_EN */
> + gpio = <&gpio3 9 0>;
> + enable-active-high;
> + };
> +};
> +
> +&am33xx_pinmux {
> + bt_pins: pinmux_bt_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_txd0.gpio0_28 - BT_EN */
> + >;
> + };
> +
> + mmc3_pins: pinmux_mmc3_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */
> + AM33XX_IOPAD(0x914, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */
> + AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */
> + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */
> + AM33XX_IOPAD(0x920, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */
> + AM33XX_IOPAD(0x908, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */
> + >;
> + };
> +
> + uart3_pins: pinmux_uart3_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* gmii1_rxd3.uart3_rxd */
> + AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gmii1_rxd2.uart3_txd */
> + AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3) /* mdio_data.uart3_ctsn */
> + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* mdio_clk.uart3_rtsn */
> + >;
> + };
> +
> + wl18xx_pins: pinmux_wl18xx_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gmii1_txclk.gpio3_9 WL_EN */
> + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk.gpio0_29 WL_IRQ */
> + AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_rxclk.gpio3_10 LS_BUF_EN */
> + >;
> + };
> +};
> +
> +&mac {
> + status = "disabled";
> +};
> +
> +&mmc3 {
> + dmas = <&edma_xbar 12 0 1
> + &edma_xbar 13 0 2>;
> + dma-names = "tx", "rx";
> + status = "okay";
> + vmmc-supply = <&wlan_en_reg>;
> + bus-width = <4>;
> + non-removable;
> + cap-power-off-card;
> + ti,needs-special-hs-handling;
> + keep-power-in-suspend;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + wlcore: wlcore at 2 {
> + compatible = "ti,wl1835";
> + reg = <2>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <29 IRQ_TYPE_EDGE_RISING>;
> + };
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart3_pins &bt_pins>;
> + status = "okay";
> +};
> +
> +&gpio3 {
> + ls_buf_en {
> + gpio-hog;
> + gpios = <10 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "LS_BUF_EN";
> + };
> +};
> --
> 2.11.0
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
2016-12-28 21:26 ` Jason Kridner
@ 2017-01-03 20:11 ` Tony Lindgren
-1 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2017-01-03 20:11 UTC (permalink / raw)
To: Jason Kridner
Cc: Robert Nelson, linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Jason Kridner
* Jason Kridner <jkridner-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> [161228 13:27]:
>
>
> > On Dec 27, 2016, at 11:58 AM, Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> >
> > BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> > replaced by a TI wl1835 wireless module.
> >
> > This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> > BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
>
> I believe the correct statement is BWxx, but BWBx reserves the option to be software incompatible in some way. My preference is to have it boot anyway, but I believe that is only dependent in the bootloader.
So does this patch need updating for that?
Regards,
Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2017-01-03 20:11 ` Tony Lindgren
0 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2017-01-03 20:11 UTC (permalink / raw)
To: linux-arm-kernel
* Jason Kridner <jkridner@gmail.com> [161228 13:27]:
>
>
> > On Dec 27, 2016, at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
> >
> > BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> > replaced by a TI wl1835 wireless module.
> >
> > This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> > BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
>
> I believe the correct statement is BWxx, but BWBx reserves the option to be software incompatible in some way. My preference is to have it boot anyway, but I believe that is only dependent in the bootloader.
So does this patch need updating for that?
Regards,
Tony
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
2017-01-03 20:11 ` Tony Lindgren
@ 2017-01-03 20:29 ` Jason Kridner
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Kridner @ 2017-01-03 20:29 UTC (permalink / raw)
To: Tony Lindgren
Cc: Robert Nelson, linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Jason Kridner
> On Jan 3, 2017, at 3:11 PM, Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org> wrote:
>
> * Jason Kridner <jkridner-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> [161228 13:27]:
>>
>>
>>> On Dec 27, 2016, at 11:58 AM, Robert Nelson <robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>>>
>>> BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
>>> replaced by a TI wl1835 wireless module.
>>>
>>> This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
>>> BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
>>
>> I believe the correct statement is BWxx, but BWBx reserves the option to be software incompatible in some way. My preference is to have it boot anyway, but I believe that is only dependent in the bootloader.
>
> So does this patch need updating for that?
No, it is bootloader controlled.
>
> Regards,
>
> Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2017-01-03 20:29 ` Jason Kridner
0 siblings, 0 replies; 26+ messages in thread
From: Jason Kridner @ 2017-01-03 20:29 UTC (permalink / raw)
To: linux-arm-kernel
> On Jan 3, 2017, at 3:11 PM, Tony Lindgren <tony@atomide.com> wrote:
>
> * Jason Kridner <jkridner@gmail.com> [161228 13:27]:
>>
>>
>>> On Dec 27, 2016, at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
>>>
>>> BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
>>> replaced by a TI wl1835 wireless module.
>>>
>>> This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
>>> BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
>>
>> I believe the correct statement is BWxx, but BWBx reserves the option to be software incompatible in some way. My preference is to have it boot anyway, but I believe that is only dependent in the bootloader.
>
> So does this patch need updating for that?
No, it is bootloader controlled.
>
> Regards,
>
> Tony
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
2017-01-03 20:29 ` Jason Kridner
@ 2017-01-03 20:43 ` Tony Lindgren
-1 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2017-01-03 20:43 UTC (permalink / raw)
To: Jason Kridner
Cc: devicetree, linux-omap, Robert Nelson, linux-arm-kernel, Jason Kridner
* Jason Kridner <jkridner@gmail.com> [170103 12:30]:
>
>
> > On Jan 3, 2017, at 3:11 PM, Tony Lindgren <tony@atomide.com> wrote:
> >
> > * Jason Kridner <jkridner@gmail.com> [161228 13:27]:
> >>
> >>
> >>> On Dec 27, 2016, at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
> >>>
> >>> BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> >>> replaced by a TI wl1835 wireless module.
> >>>
> >>> This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> >>> BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
> >>
> >> I believe the correct statement is BWxx, but BWBx reserves the option to be software incompatible in some way. My preference is to have it boot anyway, but I believe that is only dependent in the bootloader.
> >
> > So does this patch need updating for that?
>
> No, it is bootloader controlled.
What about the patch description? Does it need updating or is that
an Acked-by?
Tony
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2017-01-03 20:43 ` Tony Lindgren
0 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2017-01-03 20:43 UTC (permalink / raw)
To: linux-arm-kernel
* Jason Kridner <jkridner@gmail.com> [170103 12:30]:
>
>
> > On Jan 3, 2017, at 3:11 PM, Tony Lindgren <tony@atomide.com> wrote:
> >
> > * Jason Kridner <jkridner@gmail.com> [161228 13:27]:
> >>
> >>
> >>> On Dec 27, 2016, at 11:58 AM, Robert Nelson <robertcnelson@gmail.com> wrote:
> >>>
> >>> BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet
> >>> replaced by a TI wl1835 wireless module.
> >>>
> >>> This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom:
> >>> BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
> >>
> >> I believe the correct statement is BWxx, but BWBx reserves the option to be software incompatible in some way. My preference is to have it boot anyway, but I believe that is only dependent in the bootloader.
> >
> > So does this patch need updating for that?
>
> No, it is bootloader controlled.
What about the patch description? Does it need updating or is that
an Acked-by?
Tony
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
[not found] ` <CA+T6QPnTS-XyV0G9X78hAh=D79TkZkU+evN2RA6VF3f_jyBtkA@mail.gmail.com>
@ 2017-01-04 0:41 ` Tony Lindgren
0 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2017-01-04 0:41 UTC (permalink / raw)
To: Jason Kridner
Cc: Jason Kridner, Robert Nelson, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-omap-u79uwXL29TY76Z2rM5mHXA
* Jason Kridner <jkridner-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> [170103 12:58]:
> Asked-by: Jason Kridner <jdk-l0cyMroinI0@public.gmane.org>
>
> Sorry for the phone mailer (HTML).
OK fixed that to Acked-by :) Applied into omap-for-v4.11/dt and pushed
out.
BBB Green Wireless seems to work nicely for WLAN out of the box with
these patches :)
Regards,
Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless
@ 2017-01-04 0:41 ` Tony Lindgren
0 siblings, 0 replies; 26+ messages in thread
From: Tony Lindgren @ 2017-01-04 0:41 UTC (permalink / raw)
To: linux-arm-kernel
* Jason Kridner <jkridner@gmail.com> [170103 12:58]:
> Asked-by: Jason Kridner <jdk@ti.com>
>
> Sorry for the phone mailer (HTML).
OK fixed that to Acked-by :) Applied into omap-for-v4.11/dt and pushed
out.
BBB Green Wireless seems to work nicely for WLAN out of the box with
these patches :)
Regards,
Tony
^ permalink raw reply [flat|nested] 26+ messages in thread
end of thread, other threads:[~2017-01-04 0:41 UTC | newest]
Thread overview: 26+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-12-27 17:58 [PATCH 1/4] ARM: dts: Move most of am335x-boneblack.dts to am335x-boneblack-common.dtsi Robert Nelson
2016-12-27 17:58 ` Robert Nelson
[not found] ` <20161227175837.28970-1-robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2016-12-27 17:58 ` [PATCH 2/4] ARM: dts: Add am335x-boneblack-wireless Robert Nelson
2016-12-27 17:58 ` Robert Nelson
[not found] ` <20161227175837.28970-2-robertcnelson-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2016-12-27 18:01 ` Robert Nelson
2016-12-27 18:01 ` Robert Nelson
[not found] ` <CAOCHtYjx+KD3iy1cssjCLN0xjXBGJFZ_e1Qw2zRGbV4=X0+bHg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-12-27 18:14 ` Tony Lindgren
2016-12-27 18:14 ` Tony Lindgren
[not found] ` <20161227181429.GY4920-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2016-12-27 18:56 ` Tony Lindgren
2016-12-27 18:56 ` Tony Lindgren
2016-12-27 19:21 ` Robert Nelson
2016-12-27 19:21 ` Robert Nelson
2016-12-28 21:26 ` Jason Kridner
2016-12-28 21:26 ` Jason Kridner
[not found] ` <CB5C8999-6CAE-41F6-85A6-D2A856BD8011-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2017-01-03 20:11 ` Tony Lindgren
2017-01-03 20:11 ` Tony Lindgren
[not found] ` <20170103201103.GB25222-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2017-01-03 20:29 ` Jason Kridner
2017-01-03 20:29 ` Jason Kridner
2017-01-03 20:43 ` Tony Lindgren
2017-01-03 20:43 ` Tony Lindgren
[not found] ` <CA+T6QPnTS-XyV0G9X78hAh=D79TkZkU+evN2RA6VF3f_jyBtkA@mail.gmail.com>
[not found] ` <CA+T6QPnTS-XyV0G9X78hAh=D79TkZkU+evN2RA6VF3f_jyBtkA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-01-04 0:41 ` Tony Lindgren
2017-01-04 0:41 ` Tony Lindgren
2016-12-27 17:58 ` [PATCH 3/4] ARM: dts: Move most of am335x-bonegreen.dts to am335x-bonegreen-common.dtsi Robert Nelson
2016-12-27 17:58 ` Robert Nelson
2016-12-27 17:58 ` [PATCH 4/4] ARM: dts: Add am335x-bonegreen-wireless Robert Nelson
2016-12-27 17:58 ` Robert Nelson
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.