* [PATCH v5 0/3] add imx8dxl evk support
@ 2022-08-01 20:01 Shenwei Wang
2022-08-01 20:01 ` [PATCH v5 1/3] dt-bindings: firmware: add missing resource IDs for imx8dxl Shenwei Wang
` (2 more replies)
0 siblings, 3 replies; 12+ messages in thread
From: Shenwei Wang @ 2022-08-01 20:01 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer,
Pengutronix Kernel Team, Peng Fan
Cc: devicetree, NXP Linux Team, Shenwei Wang
i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.
The series of patches is to add the imx8dxl soc and its evk board
support.
changes in V5:
- change the "scu" node name to "system-controller"
- fix the typo in the comments for imx8dxl evk board
changes in V4:
- move i2c/mmc/serial aliases from soc to board
- correct the node names to follow the generic names recommendation
- remove some unused nodes in the evk board dts
changes in V3:
- re-order the commit sequence according to Krzysztof's feedback
- correct the syntax and styple problems pointed by Krzysztof
(Thank you for the detailed review, Krzysztof!)
- remove the unused nodes in imx8dxl-evk.dts
- dt_binding_check passed
Changes in V2:
- removed the edma2 device node because the edma v3 driver hasn't been
upstreamed yet.
- removed the imx8dxl_cm4 alias to fix the compile error.
- removed the extra blank lines at EOF.
- dt_binding_check passed.
Shenwei Wang (3):
dt-bindings: firmware: add missing resource IDs for imx8dxl
dt-bindings: arm: imx: update fsl.yaml for imx8dxl
arm64: dts: imx: add imx8dxl support
.../devicetree/bindings/arm/fsl.yaml | 6 +
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../arm64/boot/dts/freescale/imx8-ss-ddr.dtsi | 2 +-
.../arm64/boot/dts/freescale/imx8-ss-dma.dtsi | 138 ++++++
.../boot/dts/freescale/imx8-ss-lsio.dtsi | 14 +
arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 463 ++++++++++++++++++
.../boot/dts/freescale/imx8dxl-ss-adma.dtsi | 72 +++
.../boot/dts/freescale/imx8dxl-ss-conn.dtsi | 145 ++++++
.../boot/dts/freescale/imx8dxl-ss-ddr.dtsi | 9 +
.../boot/dts/freescale/imx8dxl-ss-lsio.dtsi | 78 +++
arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 238 +++++++++
include/dt-bindings/firmware/imx/rsrc.h | 7 +
12 files changed, 1172 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi
--
2.25.1
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v5 1/3] dt-bindings: firmware: add missing resource IDs for imx8dxl 2022-08-01 20:01 [PATCH v5 0/3] add imx8dxl evk support Shenwei Wang @ 2022-08-01 20:01 ` Shenwei Wang 2022-08-01 20:01 ` [PATCH v5 2/3] dt-bindings: arm: imx: update fsl.yaml " Shenwei Wang 2022-08-01 20:01 ` [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support Shenwei Wang 2 siblings, 0 replies; 12+ messages in thread From: Shenwei Wang @ 2022-08-01 20:01 UTC (permalink / raw) To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, NXP Linux Team, Shenwei Wang, Rob Herring Add the missing resource IDs for imx8dxl. Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Acked-by: Rob Herring <robh@kernel.org> --- include/dt-bindings/firmware/imx/rsrc.h | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/include/dt-bindings/firmware/imx/rsrc.h b/include/dt-bindings/firmware/imx/rsrc.h index 43885056557c4..1675de05ad33b 100644 --- a/include/dt-bindings/firmware/imx/rsrc.h +++ b/include/dt-bindings/firmware/imx/rsrc.h @@ -37,10 +37,14 @@ #define IMX_SC_R_DC_0_BLIT2 21 #define IMX_SC_R_DC_0_BLIT_OUT 22 #define IMX_SC_R_PERF 23 +#define IMX_SC_R_USB_1_PHY 24 #define IMX_SC_R_DC_0_WARP 25 +#define IMX_SC_R_V2X_MU_0 26 +#define IMX_SC_R_V2X_MU_1 27 #define IMX_SC_R_DC_0_VIDEO0 28 #define IMX_SC_R_DC_0_VIDEO1 29 #define IMX_SC_R_DC_0_FRAC0 30 +#define IMX_SC_R_V2X_MU_2 31 #define IMX_SC_R_DC_0 32 #define IMX_SC_R_GPU_2_PID0 33 #define IMX_SC_R_DC_0_PLL_0 34 @@ -49,7 +53,10 @@ #define IMX_SC_R_DC_1_BLIT1 37 #define IMX_SC_R_DC_1_BLIT2 38 #define IMX_SC_R_DC_1_BLIT_OUT 39 +#define IMX_SC_R_V2X_MU_3 40 +#define IMX_SC_R_V2X_MU_4 41 #define IMX_SC_R_DC_1_WARP 42 +#define IMX_SC_R_SECVIO 44 #define IMX_SC_R_DC_1_VIDEO0 45 #define IMX_SC_R_DC_1_VIDEO1 46 #define IMX_SC_R_DC_1_FRAC0 47 -- 2.25.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 2/3] dt-bindings: arm: imx: update fsl.yaml for imx8dxl 2022-08-01 20:01 [PATCH v5 0/3] add imx8dxl evk support Shenwei Wang 2022-08-01 20:01 ` [PATCH v5 1/3] dt-bindings: firmware: add missing resource IDs for imx8dxl Shenwei Wang @ 2022-08-01 20:01 ` Shenwei Wang 2022-08-01 20:01 ` [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support Shenwei Wang 2 siblings, 0 replies; 12+ messages in thread From: Shenwei Wang @ 2022-08-01 20:01 UTC (permalink / raw) To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, NXP Linux Team, Shenwei Wang, Krzysztof Kozlowski i.MX8DXL is a device targeting the automotive and industrial market segments. The chip is designed to achieve both high performance and low power consumption. It has a dual (2x) Cortex-A35 processor. Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 7431579ab0e85..4f4c9c0a13152 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -1034,6 +1034,12 @@ properties: - toradex,colibri-imx8x # Colibri iMX8X Modules - const: fsl,imx8qxp + - description: i.MX8DXL based Boards + items: + - enum: + - fsl,imx8dxl-evk # i.MX8DXL EVK Board + - const: fsl,imx8dxl + - description: i.MX8QXP Boards with Toradex Coilbri iMX8X Modules items: - enum: -- 2.25.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support 2022-08-01 20:01 [PATCH v5 0/3] add imx8dxl evk support Shenwei Wang 2022-08-01 20:01 ` [PATCH v5 1/3] dt-bindings: firmware: add missing resource IDs for imx8dxl Shenwei Wang 2022-08-01 20:01 ` [PATCH v5 2/3] dt-bindings: arm: imx: update fsl.yaml " Shenwei Wang @ 2022-08-01 20:01 ` Shenwei Wang 2022-08-05 16:22 ` Shenwei Wang 2022-08-21 13:14 ` Shawn Guo 2 siblings, 2 replies; 12+ messages in thread From: Shenwei Wang @ 2022-08-01 20:01 UTC (permalink / raw) To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, NXP Linux Team, Shenwei Wang i.MX8DXL is a device targeting the automotive and industrial market segments. The chip is designed to achieve both high performance and low power consumption. It has a dual (2x) Cortex-A35 processor. This patch adds the imx8dxl soc and EVK board support. Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> --- arch/arm64/boot/dts/freescale/Makefile | 1 + .../arm64/boot/dts/freescale/imx8-ss-ddr.dtsi | 2 +- .../arm64/boot/dts/freescale/imx8-ss-dma.dtsi | 138 ++++++ .../boot/dts/freescale/imx8-ss-lsio.dtsi | 14 + arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 463 ++++++++++++++++++ .../boot/dts/freescale/imx8dxl-ss-adma.dtsi | 72 +++ .../boot/dts/freescale/imx8dxl-ss-conn.dtsi | 145 ++++++ .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi | 9 + .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi | 78 +++ arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 238 +++++++++ 10 files changed, 1159 insertions(+), 1 deletion(-) create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 8bf7f7ecebaa1..2741205efe84e 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-85bb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-899b.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-data-modul-edm-sbc.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi index 8b5cad4e27002..7d5183c6c5bef 100644 --- a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi @@ -10,7 +10,7 @@ ddr_subsys: bus@5c000000 { #size-cells = <1>; ranges = <0x5c000000 0x0 0x5c000000 0x1000000>; - ddr-pmu@5c020000 { + ddr_pmu0: ddr-pmu@5c020000 { compatible = "fsl,imx8-ddr-pmu"; reg = <0x5c020000 0x10000>; interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi index 960a802b8b6ee..3944dfbdb7c9e 100644 --- a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi @@ -60,6 +60,54 @@ lpuart3: serial@5a090000 { status = "disabled"; }; + spi0_lpcg: clock-controller@5a400000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a400000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_SPI_0 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "spi0_lpcg_clk", + "spi0_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_SPI_0>; + }; + + spi1_lpcg: clock-controller@5a410000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a410000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_SPI_1 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "spi1_lpcg_clk", + "spi1_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_SPI_1>; + }; + + spi2_lpcg: clock-controller@5a420000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a420000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_SPI_2 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "spi2_lpcg_clk", + "spi2_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_SPI_2>; + }; + + spi3_lpcg: clock-controller@5a430000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a430000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_SPI_3 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "spi3_lpcg_clk", + "spi3_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_SPI_3>; + }; + uart0_lpcg: clock-controller@5a460000 { compatible = "fsl,imx8qxp-lpcg"; reg = <0x5a460000 0x10000>; @@ -108,6 +156,18 @@ uart3_lpcg: clock-controller@5a490000 { power-domains = <&pd IMX_SC_R_UART_3>; }; + emvsim0_lpcg: clock-controller@5a4d0000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a4d0000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_EMVSIM_0 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "emvsim0_lpcg_clk", + "emvsim0_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_EMVSIM_0>; + }; + i2c0: i2c@5a800000 { reg = <0x5a800000 0x4000>; interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; @@ -199,4 +259,82 @@ i2c3_lpcg: clock-controller@5ac30000 { "i2c3_lpcg_ipg_clk"; power-domains = <&pd IMX_SC_R_I2C_3>; }; + + lpspi0: spi@5a000000 { + compatible = "fsl,imx7ulp-spi"; + reg = <0x5a000000 0x10000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gic>; + clocks = <&spi0_lpcg IMX_LPCG_CLK_0>, + <&spi0_lpcg IMX_LPCG_CLK_4>; + clock-names = "per", "ipg"; + assigned-clocks = <&clk IMX_SC_R_SPI_0 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <20000000>; + power-domains = <&pd IMX_SC_R_SPI_0>; + status = "disabled"; + }; + + lpspi1: spi@5a010000 { + compatible = "fsl,imx7ulp-spi"; + reg = <0x5a010000 0x10000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gic>; + clocks = <&spi1_lpcg IMX_LPCG_CLK_0>, + <&spi1_lpcg IMX_LPCG_CLK_4>; + clock-names = "per", "ipg"; + assigned-clocks = <&clk IMX_SC_R_SPI_1 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <60000000>; + power-domains = <&pd IMX_SC_R_SPI_1>; + status = "disabled"; + }; + + lpspi2: spi@5a020000 { + compatible = "fsl,imx7ulp-spi"; + reg = <0x5a020000 0x10000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gic>; + clocks = <&spi2_lpcg IMX_LPCG_CLK_0>, + <&spi2_lpcg IMX_LPCG_CLK_4>; + clock-names = "per", "ipg"; + assigned-clocks = <&clk IMX_SC_R_SPI_2 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <60000000>; + power-domains = <&pd IMX_SC_R_SPI_2>; + status = "disabled"; + }; + + lpspi3: spi@5a030000 { + compatible = "fsl,imx7ulp-spi"; + reg = <0x5a030000 0x10000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gic>; + clocks = <&spi3_lpcg IMX_LPCG_CLK_0>, + <&spi3_lpcg IMX_LPCG_CLK_4>; + clock-names = "per", "ipg"; + assigned-clocks = <&clk IMX_SC_R_SPI_3 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <60000000>; + power-domains = <&pd IMX_SC_R_SPI_3>; + status = "disabled"; + }; + + can0_lpcg: clock-controller@5acd0000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5acd0000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_CAN_0 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>, <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>, + <IMX_LPCG_CLK_5>; + clock-output-names = "can0_lpcg_pe_clk", + "can0_lpcg_ipg_clk", + "can0_lpcg_chi_clk"; + power-domains = <&pd IMX_SC_R_CAN_0>; + }; }; diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi index 6446e6df7a9ac..61c506b0c1456 100644 --- a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi @@ -107,6 +107,20 @@ lsio_gpio7: gpio@5d0f0000 { power-domains = <&pd IMX_SC_R_GPIO_7>; }; + flexspi0: spi@5d120000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "nxp,imx8qxp-fspi"; + reg = <0x5d120000 0x10000>, <0x08000000 0x10000000>; + reg-names = "fspi_base", "fspi_mmap"; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX_SC_R_FSPI_0 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_FSPI_0 IMX_SC_PM_CLK_PER>; + clock-names = "fspi", "fspi_en"; + power-domains = <&pd IMX_SC_R_FSPI_0>; + status = "disabled"; + }; + lsio_mu0: mailbox@5d1b0000 { reg = <0x5d1b0000 0x10000>; interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts new file mode 100644 index 0000000000000..052a30182eb4e --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts @@ -0,0 +1,463 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ + +/dts-v1/; + +#include "imx8dxl.dtsi" + +/ { + model = "Freescale i.MX8DXL EVK"; + compatible = "fsl,imx8dxl-evk", "fsl,imx8dxl"; + + aliases { + i2c2 = &i2c2; + mmc0 = &usdhc1; + mmc1 = &usdhc2; + serial0 = &lpuart0; + }; + + chosen { + stdout-path = &lpuart0; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x00000000 0x80000000 0 0x40000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* + * Memory reserved for optee usage. Please do not use. + * This will be automatically added to dtb if OP-TEE is installed. + * optee@96000000 { + * reg = <0 0x96000000 0 0x2000000>; + * no-map; + * }; + */ + + /* global autoconfigured region for contiguous allocations */ + linux,cma { + compatible = "shared-dma-pool"; + reusable; + size = <0 0x14000000>; + alloc-ranges = <0 0x98000000 0 0x14000000>; + linux,cma-default; + }; + }; + + mux3_en: regulator-0 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "mux3_en"; + gpio = <&pca6416_2 8 GPIO_ACTIVE_LOW>; + regulator-always-on; + }; + + reg_fec1_sel: regulator-1 { + compatible = "regulator-fixed"; + regulator-name = "fec1_supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pca6416_1 11 GPIO_ACTIVE_HIGH>; + regulator-always-on; + status = "disabled"; + }; + + reg_fec1_io: regulator-2 { + compatible = "regulator-fixed"; + regulator-name = "fec1_io_supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&max7322 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + status = "disabled"; + }; + + reg_usdhc2_vmmc: regulator-3 { + compatible = "regulator-fixed"; + regulator-name = "SD1_SPWR"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + gpio = <&lsio_gpio4 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + off-on-delay-us = <3480>; + }; +}; + +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + nvmem-cells = <&fec_mac1>; + nvmem-cell-names = "mac-address"; + snps,reset-gpios = <&pca6416_1 2 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <10 20 200000>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + eee-broken-1000t; + qca,disable-smarteee; + vddio-supply = <&vddio0>; + + vddio0: vddio-regulator { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; +}; + +/* + * fec1 shares the some PINs with usdhc2. + * by default usdhc2 is enabled in this dts. + * Please disable usdhc2 to enable fec1 + */ +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-txid"; + phy-handle = <ðphy1>; + fsl,magic-packet; + rx-internal-delay-ps = <2000>; + nvmem-cells = <&fec_mac0>; + nvmem-cell-names = "mac-address"; + phy-reset-gpios = <&pca6416_1 0 GPIO_ACTIVE_LOW>; + phy-reset-duration = <10>; + phy-reset-post-delay = <150>; + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + qca,disable-smarteee; + vddio-supply = <&vddio1>; + + vddio1: vddio-regulator { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; +}; + +&flexspi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexspi0>; + nxp,fspi-dll-slvdly = <4>; + status = "okay"; + + mt35xu512aba0: flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <133000000>; + spi-tx-bus-width = <8>; + spi-rx-bus-width = <8>; + }; +}; + +&i2c2 { + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pca6416_1: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + + pca6416_2: gpio@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; + + pca9548_1: i2c-mux@70 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0>; + + max7322: gpio@68 { + compatible = "maxim,max7322"; + reg = <0x68>; + gpio-controller; + #gpio-cells = <2>; + status = "disabled"; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4>; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x5>; + }; + + i2c@6 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6>; + }; + }; +}; + +&lpuart0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart0>; + status = "okay"; +}; + +&lsio_gpio4 { + status = "okay"; +}; + +&lsio_gpio5 { + status = "okay"; +}; + +&thermal_zones { + pmic-thermal0 { + polling-delay-passive = <250>; + polling-delay = <2000>; + thermal-sensors = <&tsens IMX_SC_R_PMIC_0>; + + trips { + pmic_alert0: trip0 { + temperature = <110000>; + hysteresis = <2000>; + type = "passive"; + }; + pmic_crit0: trip1 { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&pmic_alert0>; + cooling-device = + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <8>; + no-sd; + no-sdio; + non-removable; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + cd-gpios = <&lsio_gpio5 1 GPIO_ACTIVE_LOW>; + wp-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>; + max-frequency = <100000000>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD 0x000514a0 + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHK_PAD 0x000014a0 + IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1 0x0600004c + IMX8DXL_SNVS_TAMPER_OUT1_LSIO_GPIO2_IO05_IN 0x0600004c + >; + }; + + pinctrl_usbotg1: usbotg1grp { + fsl,pins = < + IMX8DXL_USB_SS3_TC0_CONN_USB_OTG1_PWR 0x00000021 + >; + }; + + pinctrl_usbotg2: usbotg2grp { + fsl,pins = < + IMX8DXL_USB_SS3_TC1_CONN_USB_OTG2_PWR 0x00000021 + >; + }; + + pinctrl_eqos: eqosgrp { + fsl,pins = < + IMX8DXL_ENET0_MDC_CONN_EQOS_MDC 0x06000020 + IMX8DXL_ENET0_MDIO_CONN_EQOS_MDIO 0x06000020 + IMX8DXL_ENET1_RGMII_TX_CTL_CONN_EQOS_RGMII_TX_CTL 0x06000020 + IMX8DXL_ENET1_RGMII_TXC_CONN_EQOS_RGMII_TXC 0x06000020 + IMX8DXL_ENET1_RGMII_TXD0_CONN_EQOS_RGMII_TXD0 0x06000020 + IMX8DXL_ENET1_RGMII_TXD1_CONN_EQOS_RGMII_TXD1 0x06000020 + IMX8DXL_ENET1_RGMII_TXD2_CONN_EQOS_RGMII_TXD2 0x06000020 + IMX8DXL_ENET1_RGMII_TXD3_CONN_EQOS_RGMII_TXD3 0x06000020 + IMX8DXL_ENET1_RGMII_RXC_CONN_EQOS_RGMII_RXC 0x06000020 + IMX8DXL_ENET1_RGMII_RX_CTL_CONN_EQOS_RGMII_RX_CTL 0x06000020 + IMX8DXL_ENET1_RGMII_RXD0_CONN_EQOS_RGMII_RXD0 0x06000020 + IMX8DXL_ENET1_RGMII_RXD1_CONN_EQOS_RGMII_RXD1 0x06000020 + IMX8DXL_ENET1_RGMII_RXD2_CONN_EQOS_RGMII_RXD2 0x06000020 + IMX8DXL_ENET1_RGMII_RXD3_CONN_EQOS_RGMII_RXD3 0x06000020 + >; + }; + + pinctrl_flexspi0: flexspi0grp { + fsl,pins = < + IMX8DXL_QSPI0A_DATA0_LSIO_QSPI0A_DATA0 0x06000021 + IMX8DXL_QSPI0A_DATA1_LSIO_QSPI0A_DATA1 0x06000021 + IMX8DXL_QSPI0A_DATA2_LSIO_QSPI0A_DATA2 0x06000021 + IMX8DXL_QSPI0A_DATA3_LSIO_QSPI0A_DATA3 0x06000021 + IMX8DXL_QSPI0A_DQS_LSIO_QSPI0A_DQS 0x06000021 + IMX8DXL_QSPI0A_SS0_B_LSIO_QSPI0A_SS0_B 0x06000021 + IMX8DXL_QSPI0A_SCLK_LSIO_QSPI0A_SCLK 0x06000021 + IMX8DXL_QSPI0B_SCLK_LSIO_QSPI0B_SCLK 0x06000021 + IMX8DXL_QSPI0B_DATA0_LSIO_QSPI0B_DATA0 0x06000021 + IMX8DXL_QSPI0B_DATA1_LSIO_QSPI0B_DATA1 0x06000021 + IMX8DXL_QSPI0B_DATA2_LSIO_QSPI0B_DATA2 0x06000021 + IMX8DXL_QSPI0B_DATA3_LSIO_QSPI0B_DATA3 0x06000021 + IMX8DXL_QSPI0B_DQS_LSIO_QSPI0B_DQS 0x06000021 + IMX8DXL_QSPI0B_SS0_B_LSIO_QSPI0B_SS0_B 0x06000021 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD 0x000014a0 + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD 0x000014a0 + IMX8DXL_ENET0_MDC_CONN_ENET0_MDC 0x06000020 + IMX8DXL_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020 + IMX8DXL_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x00000060 + IMX8DXL_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x00000060 + IMX8DXL_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x00000060 + IMX8DXL_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x00000060 + IMX8DXL_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x00000060 + IMX8DXL_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x00000060 + IMX8DXL_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x00000060 + IMX8DXL_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x00000060 + IMX8DXL_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x00000060 + IMX8DXL_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x00000060 + IMX8DXL_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x00000060 + IMX8DXL_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x00000060 + >; + }; + + pinctrl_lpspi3: lpspi3grp { + fsl,pins = < + IMX8DXL_SPI3_SCK_ADMA_SPI3_SCK 0x6000040 + IMX8DXL_SPI3_SDO_ADMA_SPI3_SDO 0x6000040 + IMX8DXL_SPI3_SDI_ADMA_SPI3_SDI 0x6000040 + IMX8DXL_SPI3_CS1_ADMA_SPI3_CS1 0x6000040 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + IMX8DXL_SPI1_SCK_ADMA_I2C2_SDA 0x06000021 + IMX8DXL_SPI1_SDO_ADMA_I2C2_SCL 0x06000021 + >; + }; + + pinctrl_cm40_lpuart: cm40lpuartgrp { + fsl,pins = < + IMX8DXL_ADC_IN2_M40_UART0_RX 0x06000020 + IMX8DXL_ADC_IN3_M40_UART0_TX 0x06000020 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + IMX8DXL_SPI1_CS0_ADMA_I2C3_SDA 0x06000021 + IMX8DXL_SPI1_SDI_ADMA_I2C3_SCL 0x06000021 + >; + }; + + pinctrl_lpuart0: lpuart0grp { + fsl,pins = < + IMX8DXL_UART0_RX_ADMA_UART0_RX 0x06000020 + IMX8DXL_UART0_TX_ADMA_UART0_TX 0x06000020 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + IMX8DXL_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 + IMX8DXL_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 + IMX8DXL_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 + IMX8DXL_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 + IMX8DXL_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 + IMX8DXL_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 + IMX8DXL_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021 + IMX8DXL_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021 + IMX8DXL_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021 + IMX8DXL_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021 + IMX8DXL_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + IMX8DXL_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30 0x00000040 /* RESET_B */ + IMX8DXL_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00 0x00000021 /* WP */ + IMX8DXL_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01 0x00000021 /* CD */ + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + IMX8DXL_ENET0_RGMII_RXC_CONN_USDHC1_CLK 0x06000041 + IMX8DXL_ENET0_RGMII_RX_CTL_CONN_USDHC1_CMD 0x00000021 + IMX8DXL_ENET0_RGMII_RXD0_CONN_USDHC1_DATA0 0x00000021 + IMX8DXL_ENET0_RGMII_RXD1_CONN_USDHC1_DATA1 0x00000021 + IMX8DXL_ENET0_RGMII_RXD2_CONN_USDHC1_DATA2 0x00000021 + IMX8DXL_ENET0_RGMII_RXD3_CONN_USDHC1_DATA3 0x00000021 + IMX8DXL_ENET0_RGMII_TXD0_CONN_USDHC1_VSELECT 0x00000021 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi new file mode 100644 index 0000000000000..e26bbbf7f1508 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi @@ -0,0 +1,72 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ + +&audio_ipg_clk { + clock-frequency = <160000000>; +}; + +&dma_ipg_clk { + clock-frequency = <160000000>; +}; + +&i2c0 { + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; + interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; +}; + +&i2c1 { + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; + interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; +}; + +&i2c2 { + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; +}; + +&i2c3 { + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpspi0 { + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; + interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpspi1 { + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; + interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpspi2 { + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; + interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpspi3 { + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; + interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpuart0 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpuart1 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpuart2 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpuart3 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; + interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi new file mode 100644 index 0000000000000..98f666cbe63bf --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi @@ -0,0 +1,145 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ + +/delete-node/ &enet1_lpcg; +/delete-node/ &fec2; + +&conn_subsys { + conn_enet0_root_clk: clock-conn-enet0-root { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <250000000>; + clock-output-names = "conn_enet0_root_clk"; + }; + + eqos: ethernet@5b050000 { + compatible = "nxp,imx8dxl-dwmac-eqos", "snps,dwmac-5.10a"; + reg = <0x5b050000 0x10000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "eth_wake_irq", "macirq"; + clocks = <&eqos_lpcg IMX_LPCG_CLK_4>, + <&eqos_lpcg IMX_LPCG_CLK_6>, + <&eqos_lpcg IMX_LPCG_CLK_0>, + <&eqos_lpcg IMX_LPCG_CLK_5>, + <&eqos_lpcg IMX_LPCG_CLK_2>; + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "mem"; + assigned-clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <125000000>; + power-domains = <&pd IMX_SC_R_ENET_1>; + clk_csr = <0>; + status = "disabled"; + }; + + usbotg2: usb@5b0e0000 { + compatible = "fsl,imx8dxl-usb", "fsl,imx7ulp-usb"; + reg = <0x5b0e0000 0x200>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + fsl,usbphy = <&usbphy2>; + fsl,usbmisc = <&usbmisc2 0>; + /* + * usbotg1 and usbotg2 share one clcok. + * scu firmware disables the access to the clock and keeps + * it always on in case other core (M4) uses one of these. + */ + clocks = <&clk_dummy>; + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; + #stream-id-cells = <1>; + power-domains = <&pd IMX_SC_R_USB_1>; + status = "disabled"; + + clk_dummy: clock-dummy { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "clk_dummy"; + }; + }; + + usbmisc2: usbmisc@5b0e0200 { + #index-cells = <1>; + compatible = "fsl,imx7ulp-usbmisc"; + reg = <0x5b0e0200 0x200>; + }; + + usbphy2: usbphy@0x5b110000 { + compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy"; + reg = <0x5b110000 0x1000>; + clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>; + power-domains = <&pd IMX_SC_R_USB_1_PHY>; + status = "disabled"; + }; + + eqos_lpcg: clock-controller@5b240000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5b240000 0x10000>; + #clock-cells = <1>; + + clocks = <&conn_enet0_root_clk>, + <&conn_axi_clk>, + <&conn_axi_clk>, + <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>, + <&conn_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "eqos_ptp", + "eqos_mem_clk", + "eqos_aclk", + "eqos_clk", + "eqos_csr_clk"; + power-domains = <&pd IMX_SC_R_ENET_1>; + }; + + usb2_2_lpcg: clock-controller@5b280000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5b280000 0x10000>; + #clock-cells = <1>; + + clock-indices = <IMX_LPCG_CLK_7>; + clocks = <&conn_ipg_clk>; + clock-output-names = "usboh3_2_phy_ipg_clk"; + power-domains = <&pd IMX_SC_R_USB_1_PHY>; + }; + +}; + +&enet0_lpcg { + clocks = <&conn_enet0_root_clk>, + <&conn_enet0_root_clk>, + <&conn_axi_clk>, + <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>, + <&conn_ipg_clk>, + <&conn_ipg_clk>; +}; + +&fec1 { + compatible = "fsl,imx8qm-fec"; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; + assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>; + assigned-clock-rates = <125000000>; +}; + +&usdhc1 { + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; +}; + +&usdhc2 { + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; +}; + +&usdhc3 { + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi new file mode 100644 index 0000000000000..550f513708d85 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 NXP + */ + +&ddr_pmu0 { + compatible = "fsl,imx8-ddr-pmu"; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi new file mode 100644 index 0000000000000..4aaedb6ce591a --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi @@ -0,0 +1,78 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ +&flexspi0 { + compatible = "nxp,imx8dxl-fspi"; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio0 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio1 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio2 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio3 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio4 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio5 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio6 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio7 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu0 { + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu1 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu2 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu3 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu4 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu5 { + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi new file mode 100644 index 0000000000000..037591fb01a55 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi @@ -0,0 +1,238 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ + +#include <dt-bindings/clock/imx8-clock.h> +#include <dt-bindings/firmware/imx/rsrc.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/pads-imx8dxl.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + ethernet0 = &fec1; + ethernet1 = &eqos; + gpio0 = &lsio_gpio0; + gpio1 = &lsio_gpio1; + gpio2 = &lsio_gpio2; + gpio3 = &lsio_gpio3; + gpio4 = &lsio_gpio4; + gpio5 = &lsio_gpio5; + gpio6 = &lsio_gpio6; + gpio7 = &lsio_gpio7; + mu1 = &lsio_mu1; + }; + + cpus: cpus { + #address-cells = <2>; + #size-cells = <0>; + + /* We have 1 clusters with 2 Cortex-A35 cores */ + A35_0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a35"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&A35_L2>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; + #cooling-cells = <2>; + operating-points-v2 = <&a35_opp_table>; + }; + + A35_1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a35"; + reg = <0x0 0x1>; + enable-method = "psci"; + next-level-cache = <&A35_L2>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; + #cooling-cells = <2>; + operating-points-v2 = <&a35_opp_table>; + }; + + A35_L2: l2-cache0 { + compatible = "cache"; + }; + }; + + a35_opp_table: opp-table { + compatible = "operating-points-v2"; + opp-shared; + + opp-900000000 { + opp-hz = /bits/ 64 <900000000>; + opp-microvolt = <1000000>; + clock-latency-ns = <150000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <1100000>; + clock-latency-ns = <150000>; + opp-suspend; + }; + }; + + gic: interrupt-controller@51a00000 { + compatible = "arm,gic-v3"; + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */ + <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */ + #interrupt-cells = <3>; + interrupt-controller; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dsp_reserved: dsp@92400000 { + reg = <0 0x92400000 0 0x2000000>; + no-map; + }; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + system-controller { + compatible = "fsl,imx-scu"; + mbox-names = "tx0", + "rx0", + "gip3"; + mboxes = <&lsio_mu1 0 0 + &lsio_mu1 1 0 + &lsio_mu1 3 3>; + + pd: power-controller { + compatible = "fsl,scu-pd"; + #power-domain-cells = <1>; + wakeup-irq = <160 163 235 236 237 228 229 230 231 238 + 239 240 166 169>; + }; + + clk: clock-controller { + compatible = "fsl,imx8dxl-clk", "fsl,scu-clk"; + #clock-cells = <2>; + clocks = <&xtal32k &xtal24m>; + clock-names = "xtal_32KHz", "xtal_24Mhz"; + }; + + iomuxc: pinctrl { + compatible = "fsl,imx8dxl-iomuxc"; + }; + + ocotp: ocotp { + compatible = "fsl,imx8qxp-scu-ocotp"; + #address-cells = <1>; + #size-cells = <1>; + + fec_mac0: mac@2c4 { + reg = <0x2c4 6>; + }; + + fec_mac1: mac@2c6 { + reg = <0x2c6 6>; + }; + }; + + rtc: rtc { + compatible = "fsl,imx8qxp-sc-rtc"; + }; + + sc_pwrkey: keys { + compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key"; + linux,keycode = <KEY_POWER>; + wakeup-source; + }; + + watchdog { + compatible = "fsl,imx-sc-wdt"; + timeout-sec = <60>; + }; + + tsens: thermal-sensor { + compatible = "fsl,imx-sc-thermal"; + #thermal-sensor-cells = <1>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */ + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */ + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */ + }; + + thermal_zones: thermal-zones { + cpu-thermal0 { + polling-delay-passive = <250>; + polling-delay = <2000>; + thermal-sensors = <&tsens IMX_SC_R_SYSTEM>; + + trips { + cpu_alert0: trip0 { + temperature = <107000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit0: trip1 { + temperature = <127000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + + /* The two values below cannot be changed by the board */ + xtal32k: clock-xtal32k { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xtal_32KHz"; + }; + + xtal24m: clock-xtal24m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "xtal_24MHz"; + }; + + /* sorted in register address */ + #include "imx8-ss-adma.dtsi" + #include "imx8-ss-conn.dtsi" + #include "imx8-ss-ddr.dtsi" + #include "imx8-ss-lsio.dtsi" +}; + +#include "imx8dxl-ss-adma.dtsi" +#include "imx8dxl-ss-conn.dtsi" +#include "imx8dxl-ss-lsio.dtsi" +#include "imx8dxl-ss-ddr.dtsi" -- 2.25.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* RE: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support 2022-08-01 20:01 ` [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support Shenwei Wang @ 2022-08-05 16:22 ` Shenwei Wang 2022-08-08 5:47 ` Krzysztof Kozlowski 2022-08-18 12:08 ` Shenwei Wang 2022-08-21 13:14 ` Shawn Guo 1 sibling, 2 replies; 12+ messages in thread From: Shenwei Wang @ 2022-08-05 16:22 UTC (permalink / raw) To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, dl-linux-imx A kind ping. 😊 Regards, Shenwei > -----Original Message----- > From: Shenwei Wang <shenwei.wang@nxp.com> > Sent: Monday, August 1, 2022 3:01 PM > To: Rob Herring <robh+dt@kernel.org>; Krzysztof Kozlowski > <krzysztof.kozlowski+dt@linaro.org>; Shawn Guo <shawnguo@kernel.org>; > Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team > <kernel@pengutronix.de>; Peng Fan <peng.fan@nxp.com> > Cc: devicetree@vger.kernel.org; dl-linux-imx <linux-imx@nxp.com>; Shenwei > Wang <shenwei.wang@nxp.com> > Subject: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support > > i.MX8DXL is a device targeting the automotive and industrial market segments. > The chip is designed to achieve both high performance and low power > consumption. It has a dual (2x) Cortex-A35 processor. > > This patch adds the imx8dxl soc and EVK board support. > > Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> > --- > arch/arm64/boot/dts/freescale/Makefile | 1 + > .../arm64/boot/dts/freescale/imx8-ss-ddr.dtsi | 2 +- > .../arm64/boot/dts/freescale/imx8-ss-dma.dtsi | 138 ++++++ > .../boot/dts/freescale/imx8-ss-lsio.dtsi | 14 + > arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 463 ++++++++++++++++++ > .../boot/dts/freescale/imx8dxl-ss-adma.dtsi | 72 +++ > .../boot/dts/freescale/imx8dxl-ss-conn.dtsi | 145 ++++++ > .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi | 9 + > .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi | 78 +++ > arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 238 +++++++++ > 10 files changed, 1159 insertions(+), 1 deletion(-) create mode 100644 > arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > diff --git a/arch/arm64/boot/dts/freescale/Makefile > b/arch/arm64/boot/dts/freescale/Makefile > index 8bf7f7ecebaa1..2741205efe84e 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds- > 85bb.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-899b.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb > > +dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-data-modul-edm-sbc.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb diff --git > a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > index 8b5cad4e27002..7d5183c6c5bef 100644 > --- a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > @@ -10,7 +10,7 @@ ddr_subsys: bus@5c000000 { > #size-cells = <1>; > ranges = <0x5c000000 0x0 0x5c000000 0x1000000>; > > - ddr-pmu@5c020000 { > + ddr_pmu0: ddr-pmu@5c020000 { > compatible = "fsl,imx8-ddr-pmu"; > reg = <0x5c020000 0x10000>; > interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; diff --git > a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > index 960a802b8b6ee..3944dfbdb7c9e 100644 > --- a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > @@ -60,6 +60,54 @@ lpuart3: serial@5a090000 { > status = "disabled"; > }; > > + spi0_lpcg: clock-controller@5a400000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a400000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_SPI_0 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "spi0_lpcg_clk", > + "spi0_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_SPI_0>; > + }; > + > + spi1_lpcg: clock-controller@5a410000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a410000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_SPI_1 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "spi1_lpcg_clk", > + "spi1_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_SPI_1>; > + }; > + > + spi2_lpcg: clock-controller@5a420000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a420000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_SPI_2 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "spi2_lpcg_clk", > + "spi2_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_SPI_2>; > + }; > + > + spi3_lpcg: clock-controller@5a430000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a430000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_SPI_3 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "spi3_lpcg_clk", > + "spi3_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_SPI_3>; > + }; > + > uart0_lpcg: clock-controller@5a460000 { > compatible = "fsl,imx8qxp-lpcg"; > reg = <0x5a460000 0x10000>; > @@ -108,6 +156,18 @@ uart3_lpcg: clock-controller@5a490000 { > power-domains = <&pd IMX_SC_R_UART_3>; > }; > > + emvsim0_lpcg: clock-controller@5a4d0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a4d0000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_EMVSIM_0 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "emvsim0_lpcg_clk", > + "emvsim0_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_EMVSIM_0>; > + }; > + > i2c0: i2c@5a800000 { > reg = <0x5a800000 0x4000>; > interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; @@ -199,4 > +259,82 @@ i2c3_lpcg: clock-controller@5ac30000 { > "i2c3_lpcg_ipg_clk"; > power-domains = <&pd IMX_SC_R_I2C_3>; > }; > + > + lpspi0: spi@5a000000 { > + compatible = "fsl,imx7ulp-spi"; > + reg = <0x5a000000 0x10000>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-parent = <&gic>; > + clocks = <&spi0_lpcg IMX_LPCG_CLK_0>, > + <&spi0_lpcg IMX_LPCG_CLK_4>; > + clock-names = "per", "ipg"; > + assigned-clocks = <&clk IMX_SC_R_SPI_0 > IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <20000000>; > + power-domains = <&pd IMX_SC_R_SPI_0>; > + status = "disabled"; > + }; > + > + lpspi1: spi@5a010000 { > + compatible = "fsl,imx7ulp-spi"; > + reg = <0x5a010000 0x10000>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-parent = <&gic>; > + clocks = <&spi1_lpcg IMX_LPCG_CLK_0>, > + <&spi1_lpcg IMX_LPCG_CLK_4>; > + clock-names = "per", "ipg"; > + assigned-clocks = <&clk IMX_SC_R_SPI_1 > IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <60000000>; > + power-domains = <&pd IMX_SC_R_SPI_1>; > + status = "disabled"; > + }; > + > + lpspi2: spi@5a020000 { > + compatible = "fsl,imx7ulp-spi"; > + reg = <0x5a020000 0x10000>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-parent = <&gic>; > + clocks = <&spi2_lpcg IMX_LPCG_CLK_0>, > + <&spi2_lpcg IMX_LPCG_CLK_4>; > + clock-names = "per", "ipg"; > + assigned-clocks = <&clk IMX_SC_R_SPI_2 > IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <60000000>; > + power-domains = <&pd IMX_SC_R_SPI_2>; > + status = "disabled"; > + }; > + > + lpspi3: spi@5a030000 { > + compatible = "fsl,imx7ulp-spi"; > + reg = <0x5a030000 0x10000>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-parent = <&gic>; > + clocks = <&spi3_lpcg IMX_LPCG_CLK_0>, > + <&spi3_lpcg IMX_LPCG_CLK_4>; > + clock-names = "per", "ipg"; > + assigned-clocks = <&clk IMX_SC_R_SPI_3 > IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <60000000>; > + power-domains = <&pd IMX_SC_R_SPI_3>; > + status = "disabled"; > + }; > + > + can0_lpcg: clock-controller@5acd0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5acd0000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_CAN_0 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>, <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>, > + <IMX_LPCG_CLK_5>; > + clock-output-names = "can0_lpcg_pe_clk", > + "can0_lpcg_ipg_clk", > + "can0_lpcg_chi_clk"; > + power-domains = <&pd IMX_SC_R_CAN_0>; > + }; > }; > diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > index 6446e6df7a9ac..61c506b0c1456 100644 > --- a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > @@ -107,6 +107,20 @@ lsio_gpio7: gpio@5d0f0000 { > power-domains = <&pd IMX_SC_R_GPIO_7>; > }; > > + flexspi0: spi@5d120000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "nxp,imx8qxp-fspi"; > + reg = <0x5d120000 0x10000>, <0x08000000 0x10000000>; > + reg-names = "fspi_base", "fspi_mmap"; > + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clk IMX_SC_R_FSPI_0 IMX_SC_PM_CLK_PER>, > + <&clk IMX_SC_R_FSPI_0 IMX_SC_PM_CLK_PER>; > + clock-names = "fspi", "fspi_en"; > + power-domains = <&pd IMX_SC_R_FSPI_0>; > + status = "disabled"; > + }; > + > lsio_mu0: mailbox@5d1b0000 { > reg = <0x5d1b0000 0x10000>; > interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; diff --git > a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > new file mode 100644 > index 0000000000000..052a30182eb4e > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > @@ -0,0 +1,463 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > + > +/dts-v1/; > + > +#include "imx8dxl.dtsi" > + > +/ { > + model = "Freescale i.MX8DXL EVK"; > + compatible = "fsl,imx8dxl-evk", "fsl,imx8dxl"; > + > + aliases { > + i2c2 = &i2c2; > + mmc0 = &usdhc1; > + mmc1 = &usdhc2; > + serial0 = &lpuart0; > + }; > + > + chosen { > + stdout-path = &lpuart0; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + reg = <0x00000000 0x80000000 0 0x40000000>; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + /* > + * Memory reserved for optee usage. Please do not use. > + * This will be automatically added to dtb if OP-TEE is installed. > + * optee@96000000 { > + * reg = <0 0x96000000 0 0x2000000>; > + * no-map; > + * }; > + */ > + > + /* global autoconfigured region for contiguous allocations */ > + linux,cma { > + compatible = "shared-dma-pool"; > + reusable; > + size = <0 0x14000000>; > + alloc-ranges = <0 0x98000000 0 0x14000000>; > + linux,cma-default; > + }; > + }; > + > + mux3_en: regulator-0 { > + compatible = "regulator-fixed"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "mux3_en"; > + gpio = <&pca6416_2 8 GPIO_ACTIVE_LOW>; > + regulator-always-on; > + }; > + > + reg_fec1_sel: regulator-1 { > + compatible = "regulator-fixed"; > + regulator-name = "fec1_supply"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&pca6416_1 11 GPIO_ACTIVE_HIGH>; > + regulator-always-on; > + status = "disabled"; > + }; > + > + reg_fec1_io: regulator-2 { > + compatible = "regulator-fixed"; > + regulator-name = "fec1_io_supply"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + gpio = <&max7322 0 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-always-on; > + status = "disabled"; > + }; > + > + reg_usdhc2_vmmc: regulator-3 { > + compatible = "regulator-fixed"; > + regulator-name = "SD1_SPWR"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + gpio = <&lsio_gpio4 30 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + off-on-delay-us = <3480>; > + }; > +}; > + > +&eqos { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_eqos>; > + phy-mode = "rgmii-id"; > + phy-handle = <ðphy0>; > + nvmem-cells = <&fec_mac1>; > + nvmem-cell-names = "mac-address"; > + snps,reset-gpios = <&pca6416_1 2 GPIO_ACTIVE_LOW>; > + snps,reset-delays-us = <10 20 200000>; > + status = "okay"; > + > + mdio { > + compatible = "snps,dwmac-mdio"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy0: ethernet-phy@0 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <0>; > + eee-broken-1000t; > + qca,disable-smarteee; > + vddio-supply = <&vddio0>; > + > + vddio0: vddio-regulator { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + }; > + }; > +}; > + > +/* > + * fec1 shares the some PINs with usdhc2. > + * by default usdhc2 is enabled in this dts. > + * Please disable usdhc2 to enable fec1 */ > +&fec1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_fec1>; > + phy-mode = "rgmii-txid"; > + phy-handle = <ðphy1>; > + fsl,magic-packet; > + rx-internal-delay-ps = <2000>; > + nvmem-cells = <&fec_mac0>; > + nvmem-cell-names = "mac-address"; > + phy-reset-gpios = <&pca6416_1 0 GPIO_ACTIVE_LOW>; > + phy-reset-duration = <10>; > + phy-reset-post-delay = <150>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy1: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + qca,disable-smarteee; > + vddio-supply = <&vddio1>; > + > + vddio1: vddio-regulator { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + }; > + }; > +}; > + > +&flexspi0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_flexspi0>; > + nxp,fspi-dll-slvdly = <4>; > + status = "okay"; > + > + mt35xu512aba0: flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0>; > + #address-cells = <1>; > + #size-cells = <1>; > + spi-max-frequency = <133000000>; > + spi-tx-bus-width = <8>; > + spi-rx-bus-width = <8>; > + }; > +}; > + > +&i2c2 { > + #address-cells = <1>; > + #size-cells = <0>; > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + pca6416_1: gpio@20 { > + compatible = "ti,tca6416"; > + reg = <0x20>; > + gpio-controller; > + #gpio-cells = <2>; > + }; > + > + pca6416_2: gpio@21 { > + compatible = "ti,tca6416"; > + reg = <0x21>; > + gpio-controller; > + #gpio-cells = <2>; > + }; > + > + pca9548_1: i2c-mux@70 { > + compatible = "nxp,pca9548"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x70>; > + > + i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x0>; > + > + max7322: gpio@68 { > + compatible = "maxim,max7322"; > + reg = <0x68>; > + gpio-controller; > + #gpio-cells = <2>; > + status = "disabled"; > + }; > + }; > + > + i2c@4 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x4>; > + }; > + > + i2c@5 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x5>; > + }; > + > + i2c@6 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x6>; > + }; > + }; > +}; > + > +&lpuart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_lpuart0>; > + status = "okay"; > +}; > + > +&lsio_gpio4 { > + status = "okay"; > +}; > + > +&lsio_gpio5 { > + status = "okay"; > +}; > + > +&thermal_zones { > + pmic-thermal0 { > + polling-delay-passive = <250>; > + polling-delay = <2000>; > + thermal-sensors = <&tsens IMX_SC_R_PMIC_0>; > + > + trips { > + pmic_alert0: trip0 { > + temperature = <110000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + pmic_crit0: trip1 { > + temperature = <125000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&pmic_alert0>; > + cooling-device = > + <&A35_0 THERMAL_NO_LIMIT > THERMAL_NO_LIMIT>, > + <&A35_1 THERMAL_NO_LIMIT > THERMAL_NO_LIMIT>; > + }; > + }; > + }; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + bus-width = <8>; > + no-sd; > + no-sdio; > + non-removable; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; > + bus-width = <4>; > + vmmc-supply = <®_usdhc2_vmmc>; > + cd-gpios = <&lsio_gpio5 1 GPIO_ACTIVE_LOW>; > + wp-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>; > + max-frequency = <100000000>; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + pinctrl_hog: hoggrp { > + fsl,pins = < > + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD > 0x000514a0 > + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHK_PAD > 0x000014a0 > + IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1 > 0x0600004c > + IMX8DXL_SNVS_TAMPER_OUT1_LSIO_GPIO2_IO05_IN > 0x0600004c > + >; > + }; > + > + pinctrl_usbotg1: usbotg1grp { > + fsl,pins = < > + IMX8DXL_USB_SS3_TC0_CONN_USB_OTG1_PWR > 0x00000021 > + >; > + }; > + > + pinctrl_usbotg2: usbotg2grp { > + fsl,pins = < > + IMX8DXL_USB_SS3_TC1_CONN_USB_OTG2_PWR > 0x00000021 > + >; > + }; > + > + pinctrl_eqos: eqosgrp { > + fsl,pins = < > + IMX8DXL_ENET0_MDC_CONN_EQOS_MDC > 0x06000020 > + IMX8DXL_ENET0_MDIO_CONN_EQOS_MDIO > 0x06000020 > + > IMX8DXL_ENET1_RGMII_TX_CTL_CONN_EQOS_RGMII_TX_CTL > 0x06000020 > + > IMX8DXL_ENET1_RGMII_TXC_CONN_EQOS_RGMII_TXC > 0x06000020 > + > IMX8DXL_ENET1_RGMII_TXD0_CONN_EQOS_RGMII_TXD0 > 0x06000020 > + > IMX8DXL_ENET1_RGMII_TXD1_CONN_EQOS_RGMII_TXD1 > 0x06000020 > + > IMX8DXL_ENET1_RGMII_TXD2_CONN_EQOS_RGMII_TXD2 > 0x06000020 > + > IMX8DXL_ENET1_RGMII_TXD3_CONN_EQOS_RGMII_TXD3 > 0x06000020 > + > IMX8DXL_ENET1_RGMII_RXC_CONN_EQOS_RGMII_RXC > 0x06000020 > + > IMX8DXL_ENET1_RGMII_RX_CTL_CONN_EQOS_RGMII_RX_CTL > 0x06000020 > + > IMX8DXL_ENET1_RGMII_RXD0_CONN_EQOS_RGMII_RXD0 > 0x06000020 > + > IMX8DXL_ENET1_RGMII_RXD1_CONN_EQOS_RGMII_RXD1 > 0x06000020 > + > IMX8DXL_ENET1_RGMII_RXD2_CONN_EQOS_RGMII_RXD2 > 0x06000020 > + > IMX8DXL_ENET1_RGMII_RXD3_CONN_EQOS_RGMII_RXD3 > 0x06000020 > + >; > + }; > + > + pinctrl_flexspi0: flexspi0grp { > + fsl,pins = < > + IMX8DXL_QSPI0A_DATA0_LSIO_QSPI0A_DATA0 > 0x06000021 > + IMX8DXL_QSPI0A_DATA1_LSIO_QSPI0A_DATA1 > 0x06000021 > + IMX8DXL_QSPI0A_DATA2_LSIO_QSPI0A_DATA2 > 0x06000021 > + IMX8DXL_QSPI0A_DATA3_LSIO_QSPI0A_DATA3 > 0x06000021 > + IMX8DXL_QSPI0A_DQS_LSIO_QSPI0A_DQS > 0x06000021 > + IMX8DXL_QSPI0A_SS0_B_LSIO_QSPI0A_SS0_B > 0x06000021 > + IMX8DXL_QSPI0A_SCLK_LSIO_QSPI0A_SCLK > 0x06000021 > + IMX8DXL_QSPI0B_SCLK_LSIO_QSPI0B_SCLK > 0x06000021 > + IMX8DXL_QSPI0B_DATA0_LSIO_QSPI0B_DATA0 > 0x06000021 > + IMX8DXL_QSPI0B_DATA1_LSIO_QSPI0B_DATA1 > 0x06000021 > + IMX8DXL_QSPI0B_DATA2_LSIO_QSPI0B_DATA2 > 0x06000021 > + IMX8DXL_QSPI0B_DATA3_LSIO_QSPI0B_DATA3 > 0x06000021 > + IMX8DXL_QSPI0B_DQS_LSIO_QSPI0B_DQS > 0x06000021 > + IMX8DXL_QSPI0B_SS0_B_LSIO_QSPI0B_SS0_B > 0x06000021 > + >; > + }; > + > + pinctrl_fec1: fec1grp { > + fsl,pins = < > + > IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD > 0x000014a0 > + > IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD > 0x000014a0 > + IMX8DXL_ENET0_MDC_CONN_ENET0_MDC > 0x06000020 > + IMX8DXL_ENET0_MDIO_CONN_ENET0_MDIO > 0x06000020 > + > IMX8DXL_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL > 0x00000060 > + > IMX8DXL_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC > 0x00000060 > + > IMX8DXL_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 > 0x00000060 > + > IMX8DXL_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 > 0x00000060 > + > IMX8DXL_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 > 0x00000060 > + > IMX8DXL_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 > 0x00000060 > + > IMX8DXL_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC > 0x00000060 > + > IMX8DXL_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL > 0x00000060 > + > IMX8DXL_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 > 0x00000060 > + > IMX8DXL_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 > 0x00000060 > + > IMX8DXL_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 > 0x00000060 > + > IMX8DXL_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 > 0x00000060 > + >; > + }; > + > + pinctrl_lpspi3: lpspi3grp { > + fsl,pins = < > + IMX8DXL_SPI3_SCK_ADMA_SPI3_SCK > 0x6000040 > + IMX8DXL_SPI3_SDO_ADMA_SPI3_SDO > 0x6000040 > + IMX8DXL_SPI3_SDI_ADMA_SPI3_SDI > 0x6000040 > + IMX8DXL_SPI3_CS1_ADMA_SPI3_CS1 > 0x6000040 > + >; > + }; > + > + pinctrl_i2c2: i2c2grp { > + fsl,pins = < > + IMX8DXL_SPI1_SCK_ADMA_I2C2_SDA > 0x06000021 > + IMX8DXL_SPI1_SDO_ADMA_I2C2_SCL > 0x06000021 > + >; > + }; > + > + pinctrl_cm40_lpuart: cm40lpuartgrp { > + fsl,pins = < > + IMX8DXL_ADC_IN2_M40_UART0_RX > 0x06000020 > + IMX8DXL_ADC_IN3_M40_UART0_TX > 0x06000020 > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + IMX8DXL_SPI1_CS0_ADMA_I2C3_SDA > 0x06000021 > + IMX8DXL_SPI1_SDI_ADMA_I2C3_SCL > 0x06000021 > + >; > + }; > + > + pinctrl_lpuart0: lpuart0grp { > + fsl,pins = < > + IMX8DXL_UART0_RX_ADMA_UART0_RX > 0x06000020 > + IMX8DXL_UART0_TX_ADMA_UART0_TX > 0x06000020 > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + IMX8DXL_EMMC0_CLK_CONN_EMMC0_CLK > 0x06000041 > + IMX8DXL_EMMC0_CMD_CONN_EMMC0_CMD > 0x00000021 > + IMX8DXL_EMMC0_DATA0_CONN_EMMC0_DATA0 > 0x00000021 > + IMX8DXL_EMMC0_DATA1_CONN_EMMC0_DATA1 > 0x00000021 > + IMX8DXL_EMMC0_DATA2_CONN_EMMC0_DATA2 > 0x00000021 > + IMX8DXL_EMMC0_DATA3_CONN_EMMC0_DATA3 > 0x00000021 > + IMX8DXL_EMMC0_DATA4_CONN_EMMC0_DATA4 > 0x00000021 > + IMX8DXL_EMMC0_DATA5_CONN_EMMC0_DATA5 > 0x00000021 > + IMX8DXL_EMMC0_DATA6_CONN_EMMC0_DATA6 > 0x00000021 > + IMX8DXL_EMMC0_DATA7_CONN_EMMC0_DATA7 > 0x00000021 > + IMX8DXL_EMMC0_STROBE_CONN_EMMC0_STROBE > 0x00000041 > + >; > + }; > + > + pinctrl_usdhc2_gpio: usdhc2gpiogrp { > + fsl,pins = < > + IMX8DXL_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30 > 0x00000040 /* RESET_B */ > + IMX8DXL_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00 > 0x00000021 /* WP */ > + IMX8DXL_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01 > 0x00000021 /* CD */ > + >; > + }; > + > + pinctrl_usdhc2: usdhc2grp { > + fsl,pins = < > + IMX8DXL_ENET0_RGMII_RXC_CONN_USDHC1_CLK > 0x06000041 > + > IMX8DXL_ENET0_RGMII_RX_CTL_CONN_USDHC1_CMD 0x00000021 > + > IMX8DXL_ENET0_RGMII_RXD0_CONN_USDHC1_DATA0 0x00000021 > + > IMX8DXL_ENET0_RGMII_RXD1_CONN_USDHC1_DATA1 0x00000021 > + > IMX8DXL_ENET0_RGMII_RXD2_CONN_USDHC1_DATA2 0x00000021 > + > IMX8DXL_ENET0_RGMII_RXD3_CONN_USDHC1_DATA3 0x00000021 > + > IMX8DXL_ENET0_RGMII_TXD0_CONN_USDHC1_VSELECT > 0x00000021 > + >; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > new file mode 100644 > index 0000000000000..e26bbbf7f1508 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > @@ -0,0 +1,72 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > + > +&audio_ipg_clk { > + clock-frequency = <160000000>; > +}; > + > +&dma_ipg_clk { > + clock-frequency = <160000000>; > +}; > + > +&i2c0 { > + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > + interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&i2c1 { > + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > + interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&i2c2 { > + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&i2c3 { > + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lpspi0 { > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > + interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lpspi1 { > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > + interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lpspi2 { > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > + interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lpspi3 { > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > + interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lpuart0 { > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lpuart1 { > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lpuart2 { > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lpuart3 { > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > + interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>; }; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > new file mode 100644 > index 0000000000000..98f666cbe63bf > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > @@ -0,0 +1,145 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > + > +/delete-node/ &enet1_lpcg; > +/delete-node/ &fec2; > + > +&conn_subsys { > + conn_enet0_root_clk: clock-conn-enet0-root { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <250000000>; > + clock-output-names = "conn_enet0_root_clk"; > + }; > + > + eqos: ethernet@5b050000 { > + compatible = "nxp,imx8dxl-dwmac-eqos", "snps,dwmac-5.10a"; > + reg = <0x5b050000 0x10000>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "eth_wake_irq", "macirq"; > + clocks = <&eqos_lpcg IMX_LPCG_CLK_4>, > + <&eqos_lpcg IMX_LPCG_CLK_6>, > + <&eqos_lpcg IMX_LPCG_CLK_0>, > + <&eqos_lpcg IMX_LPCG_CLK_5>, > + <&eqos_lpcg IMX_LPCG_CLK_2>; > + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "mem"; > + assigned-clocks = <&clk IMX_SC_R_ENET_1 > IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <125000000>; > + power-domains = <&pd IMX_SC_R_ENET_1>; > + clk_csr = <0>; > + status = "disabled"; > + }; > + > + usbotg2: usb@5b0e0000 { > + compatible = "fsl,imx8dxl-usb", "fsl,imx7ulp-usb"; > + reg = <0x5b0e0000 0x200>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; > + fsl,usbphy = <&usbphy2>; > + fsl,usbmisc = <&usbmisc2 0>; > + /* > + * usbotg1 and usbotg2 share one clcok. > + * scu firmware disables the access to the clock and keeps > + * it always on in case other core (M4) uses one of these. > + */ > + clocks = <&clk_dummy>; > + ahb-burst-config = <0x0>; > + tx-burst-size-dword = <0x10>; > + rx-burst-size-dword = <0x10>; > + #stream-id-cells = <1>; > + power-domains = <&pd IMX_SC_R_USB_1>; > + status = "disabled"; > + > + clk_dummy: clock-dummy { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <0>; > + clock-output-names = "clk_dummy"; > + }; > + }; > + > + usbmisc2: usbmisc@5b0e0200 { > + #index-cells = <1>; > + compatible = "fsl,imx7ulp-usbmisc"; > + reg = <0x5b0e0200 0x200>; > + }; > + > + usbphy2: usbphy@0x5b110000 { > + compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy"; > + reg = <0x5b110000 0x1000>; > + clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>; > + power-domains = <&pd IMX_SC_R_USB_1_PHY>; > + status = "disabled"; > + }; > + > + eqos_lpcg: clock-controller@5b240000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5b240000 0x10000>; > + #clock-cells = <1>; > + > + clocks = <&conn_enet0_root_clk>, > + <&conn_axi_clk>, > + <&conn_axi_clk>, > + <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>, > + <&conn_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>, > + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, > + <IMX_LPCG_CLK_6>; > + clock-output-names = "eqos_ptp", > + "eqos_mem_clk", > + "eqos_aclk", > + "eqos_clk", > + "eqos_csr_clk"; > + power-domains = <&pd IMX_SC_R_ENET_1>; > + }; > + > + usb2_2_lpcg: clock-controller@5b280000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5b280000 0x10000>; > + #clock-cells = <1>; > + > + clock-indices = <IMX_LPCG_CLK_7>; > + clocks = <&conn_ipg_clk>; > + clock-output-names = "usboh3_2_phy_ipg_clk"; > + power-domains = <&pd IMX_SC_R_USB_1_PHY>; > + }; > + > +}; > + > +&enet0_lpcg { > + clocks = <&conn_enet0_root_clk>, > + <&conn_enet0_root_clk>, > + <&conn_axi_clk>, > + <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>, > + <&conn_ipg_clk>, > + <&conn_ipg_clk>; > +}; > + > +&fec1 { > + compatible = "fsl,imx8qm-fec"; > + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; > + assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>; > + assigned-clock-rates = <125000000>; > +}; > + > +&usdhc1 { > + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; > + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&usdhc2 { > + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; > + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&usdhc3 { > + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; }; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > new file mode 100644 > index 0000000000000..550f513708d85 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > @@ -0,0 +1,9 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2020 NXP > + */ > + > +&ddr_pmu0 { > + compatible = "fsl,imx8-ddr-pmu"; > + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; }; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > new file mode 100644 > index 0000000000000..4aaedb6ce591a > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > @@ -0,0 +1,78 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > +&flexspi0 { > + compatible = "nxp,imx8dxl-fspi"; > + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_gpio0 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_gpio1 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_gpio2 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_gpio3 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_gpio4 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_gpio5 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_gpio6 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_gpio7 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_mu0 { > + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_mu1 { > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_mu2 { > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_mu3 { > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_mu4 { > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; }; > + > +&lsio_mu5 { > + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; }; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > new file mode 100644 > index 0000000000000..037591fb01a55 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > @@ -0,0 +1,238 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > + > +#include <dt-bindings/clock/imx8-clock.h> #include > +<dt-bindings/firmware/imx/rsrc.h> > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/pinctrl/pads-imx8dxl.h> > +#include <dt-bindings/thermal/thermal.h> > + > +/ { > + interrupt-parent = <&gic>; > + #address-cells = <2>; > + #size-cells = <2>; > + > + aliases { > + ethernet0 = &fec1; > + ethernet1 = &eqos; > + gpio0 = &lsio_gpio0; > + gpio1 = &lsio_gpio1; > + gpio2 = &lsio_gpio2; > + gpio3 = &lsio_gpio3; > + gpio4 = &lsio_gpio4; > + gpio5 = &lsio_gpio5; > + gpio6 = &lsio_gpio6; > + gpio7 = &lsio_gpio7; > + mu1 = &lsio_mu1; > + }; > + > + cpus: cpus { > + #address-cells = <2>; > + #size-cells = <0>; > + > + /* We have 1 clusters with 2 Cortex-A35 cores */ > + A35_0: cpu@0 { > + device_type = "cpu"; > + compatible = "arm,cortex-a35"; > + reg = <0x0 0x0>; > + enable-method = "psci"; > + next-level-cache = <&A35_L2>; > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > + #cooling-cells = <2>; > + operating-points-v2 = <&a35_opp_table>; > + }; > + > + A35_1: cpu@1 { > + device_type = "cpu"; > + compatible = "arm,cortex-a35"; > + reg = <0x0 0x1>; > + enable-method = "psci"; > + next-level-cache = <&A35_L2>; > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > + #cooling-cells = <2>; > + operating-points-v2 = <&a35_opp_table>; > + }; > + > + A35_L2: l2-cache0 { > + compatible = "cache"; > + }; > + }; > + > + a35_opp_table: opp-table { > + compatible = "operating-points-v2"; > + opp-shared; > + > + opp-900000000 { > + opp-hz = /bits/ 64 <900000000>; > + opp-microvolt = <1000000>; > + clock-latency-ns = <150000>; > + }; > + > + opp-1200000000 { > + opp-hz = /bits/ 64 <1200000000>; > + opp-microvolt = <1100000>; > + clock-latency-ns = <150000>; > + opp-suspend; > + }; > + }; > + > + gic: interrupt-controller@51a00000 { > + compatible = "arm,gic-v3"; > + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */ > + <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) > */ > + #interrupt-cells = <3>; > + interrupt-controller; > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + dsp_reserved: dsp@92400000 { > + reg = <0 0x92400000 0 0x2000000>; > + no-map; > + }; > + }; > + > + pmu { > + compatible = "arm,armv8-pmuv3"; > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + system-controller { > + compatible = "fsl,imx-scu"; > + mbox-names = "tx0", > + "rx0", > + "gip3"; > + mboxes = <&lsio_mu1 0 0 > + &lsio_mu1 1 0 > + &lsio_mu1 3 3>; > + > + pd: power-controller { > + compatible = "fsl,scu-pd"; > + #power-domain-cells = <1>; > + wakeup-irq = <160 163 235 236 237 228 229 230 231 > 238 > + 239 240 166 169>; > + }; > + > + clk: clock-controller { > + compatible = "fsl,imx8dxl-clk", "fsl,scu-clk"; > + #clock-cells = <2>; > + clocks = <&xtal32k &xtal24m>; > + clock-names = "xtal_32KHz", "xtal_24Mhz"; > + }; > + > + iomuxc: pinctrl { > + compatible = "fsl,imx8dxl-iomuxc"; > + }; > + > + ocotp: ocotp { > + compatible = "fsl,imx8qxp-scu-ocotp"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + fec_mac0: mac@2c4 { > + reg = <0x2c4 6>; > + }; > + > + fec_mac1: mac@2c6 { > + reg = <0x2c6 6>; > + }; > + }; > + > + rtc: rtc { > + compatible = "fsl,imx8qxp-sc-rtc"; > + }; > + > + sc_pwrkey: keys { > + compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key"; > + linux,keycode = <KEY_POWER>; > + wakeup-source; > + }; > + > + watchdog { > + compatible = "fsl,imx-sc-wdt"; > + timeout-sec = <60>; > + }; > + > + tsens: thermal-sensor { > + compatible = "fsl,imx-sc-thermal"; > + #thermal-sensor-cells = <1>; > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical > Secure */ > + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical > Non-Secure */ > + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ > + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor > */ > + }; > + > + thermal_zones: thermal-zones { > + cpu-thermal0 { > + polling-delay-passive = <250>; > + polling-delay = <2000>; > + thermal-sensors = <&tsens IMX_SC_R_SYSTEM>; > + > + trips { > + cpu_alert0: trip0 { > + temperature = <107000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + cpu_crit0: trip1 { > + temperature = <127000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&cpu_alert0>; > + cooling-device = > + <&A35_0 THERMAL_NO_LIMIT > THERMAL_NO_LIMIT>, > + <&A35_1 THERMAL_NO_LIMIT > THERMAL_NO_LIMIT>; > + }; > + }; > + }; > + }; > + > + /* The two values below cannot be changed by the board */ > + xtal32k: clock-xtal32k { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <32768>; > + clock-output-names = "xtal_32KHz"; > + }; > + > + xtal24m: clock-xtal24m { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <24000000>; > + clock-output-names = "xtal_24MHz"; > + }; > + > + /* sorted in register address */ > + #include "imx8-ss-adma.dtsi" > + #include "imx8-ss-conn.dtsi" > + #include "imx8-ss-ddr.dtsi" > + #include "imx8-ss-lsio.dtsi" > +}; > + > +#include "imx8dxl-ss-adma.dtsi" > +#include "imx8dxl-ss-conn.dtsi" > +#include "imx8dxl-ss-lsio.dtsi" > +#include "imx8dxl-ss-ddr.dtsi" > -- > 2.25.1 ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support 2022-08-05 16:22 ` Shenwei Wang @ 2022-08-08 5:47 ` Krzysztof Kozlowski 2022-08-08 18:16 ` [EXT] " Shenwei Wang 2022-08-18 12:08 ` Shenwei Wang 1 sibling, 1 reply; 12+ messages in thread From: Krzysztof Kozlowski @ 2022-08-08 5:47 UTC (permalink / raw) To: Shenwei Wang, Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, dl-linux-imx On 05/08/2022 18:22, Shenwei Wang wrote: > A kind ping. 😊 > > To whom? What do you need from me? Regards, > Shenwei > >> -----Original Message----- >> From: Shenwei Wang <shenwei.wang@nxp.com> >> Sent: Monday, August 1, 2022 3:01 PM >> To: Rob Herring <robh+dt@kernel.org>; Krzysztof Kozlowski >> <krzysztof.kozlowski+dt@linaro.org>; Shawn Guo <shawnguo@kernel.org>; >> Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team >> <kernel@pengutronix.de>; Peng Fan <peng.fan@nxp.com> >> Cc: devicetree@vger.kernel.org; dl-linux-imx <linux-imx@nxp.com>; Shenwei >> Wang <shenwei.wang@nxp.com> >> Subject: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support >> >> i.MX8DXL is a device targeting the automotive and industrial market segments. >> The chip is designed to achieve both high performance and low power >> consumption. It has a dual (2x) Cortex-A35 processor. >> >> This patch adds the imx8dxl soc and EVK board support. >> >> Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> >> --- >> arch/arm64/boot/dts/freescale/Makefile | 1 + >> .../arm64/boot/dts/freescale/imx8-ss-ddr.dtsi | 2 +- >> .../arm64/boot/dts/freescale/imx8-ss-dma.dtsi | 138 ++++++ >> .../boot/dts/freescale/imx8-ss-lsio.dtsi | 14 + >> arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 463 ++++++++++++++++++ >> .../boot/dts/freescale/imx8dxl-ss-adma.dtsi | 72 +++ >> .../boot/dts/freescale/imx8dxl-ss-conn.dtsi | 145 ++++++ >> .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi | 9 + >> .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi | 78 +++ >> arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 238 +++++++++ Best regards, Krzysztof ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [EXT] Re: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support 2022-08-08 5:47 ` Krzysztof Kozlowski @ 2022-08-08 18:16 ` Shenwei Wang 2022-08-09 4:16 ` Krzysztof Kozlowski 0 siblings, 1 reply; 12+ messages in thread From: Shenwei Wang @ 2022-08-08 18:16 UTC (permalink / raw) To: Krzysztof Kozlowski, Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, dl-linux-imx > -----Original Message----- > From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > Sent: Monday, August 8, 2022 12:47 AM > To: Shenwei Wang <shenwei.wang@nxp.com>; Rob Herring > <robh+dt@kernel.org>; Krzysztof Kozlowski > <krzysztof.kozlowski+dt@linaro.org>; Shawn Guo <shawnguo@kernel.org>; > Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team > <kernel@pengutronix.de>; Peng Fan <peng.fan@nxp.com> > Cc: devicetree@vger.kernel.org; dl-linux-imx <linux-imx@nxp.com> > Subject: [EXT] Re: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support > > Caution: EXT Email > > On 05/08/2022 18:22, Shenwei Wang wrote: > > A kind ping. 😊 > > > > > > To whom? What do you need from me? > This the version 5 of the series of patches, and should have addressed all those comments from you and other reviewers. The other two commits were acked by you and Rob. This one hasn't gotten any feedback or ack so far. I would greatly appreciate it if you or Rob could ack it or let me know where to improve. Thanks, Shenwei > Regards, > > Shenwei > > > >> -----Original Message----- > >> From: Shenwei Wang <shenwei.wang@nxp.com> > >> Sent: Monday, August 1, 2022 3:01 PM > >> To: Rob Herring <robh+dt@kernel.org>; Krzysztof Kozlowski > >> <krzysztof.kozlowski+dt@linaro.org>; Shawn Guo <shawnguo@kernel.org>; > >> Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team > >> <kernel@pengutronix.de>; Peng Fan <peng.fan@nxp.com> > >> Cc: devicetree@vger.kernel.org; dl-linux-imx <linux-imx@nxp.com>; > >> Shenwei Wang <shenwei.wang@nxp.com> > >> Subject: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support > >> > >> i.MX8DXL is a device targeting the automotive and industrial market > segments. > >> The chip is designed to achieve both high performance and low power > >> consumption. It has a dual (2x) Cortex-A35 processor. > >> > >> This patch adds the imx8dxl soc and EVK board support. > >> > >> Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> > >> --- > >> arch/arm64/boot/dts/freescale/Makefile | 1 + > >> .../arm64/boot/dts/freescale/imx8-ss-ddr.dtsi | 2 +- > >> .../arm64/boot/dts/freescale/imx8-ss-dma.dtsi | 138 ++++++ > >> .../boot/dts/freescale/imx8-ss-lsio.dtsi | 14 + > >> arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 463 ++++++++++++++++++ > >> .../boot/dts/freescale/imx8dxl-ss-adma.dtsi | 72 +++ > >> .../boot/dts/freescale/imx8dxl-ss-conn.dtsi | 145 ++++++ > >> .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi | 9 + > >> .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi | 78 +++ > >> arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 238 +++++++++ > > > Best regards, > Krzysztof ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [EXT] Re: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support 2022-08-08 18:16 ` [EXT] " Shenwei Wang @ 2022-08-09 4:16 ` Krzysztof Kozlowski 2022-08-09 16:41 ` Shenwei Wang 0 siblings, 1 reply; 12+ messages in thread From: Krzysztof Kozlowski @ 2022-08-09 4:16 UTC (permalink / raw) To: Shenwei Wang, Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, dl-linux-imx On 08/08/2022 21:16, Shenwei Wang wrote: >> On 05/08/2022 18:22, Shenwei Wang wrote: >>> A kind ping. 😊 >>> >>> >> >> To whom? What do you need from me? >> > > This the version 5 of the series of patches, and should have addressed all those comments from you and other reviewers. The other two commits were acked by you and Rob. This one hasn't gotten any feedback or ack so far. I would greatly appreciate it if you or Rob could ack it or let me know where to improve. This is not a DT bindings patch. Why do you need or expect my ack? Best regards, Krzysztof ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [EXT] Re: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support 2022-08-09 4:16 ` Krzysztof Kozlowski @ 2022-08-09 16:41 ` Shenwei Wang 0 siblings, 0 replies; 12+ messages in thread From: Shenwei Wang @ 2022-08-09 16:41 UTC (permalink / raw) To: Krzysztof Kozlowski, Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, dl-linux-imx, linux-arm-kernel, imx Hi Shawn, Any comments regarding this patch? Thanks, Shenwei > -----Original Message----- > From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > Sent: Monday, August 8, 2022 11:16 PM > To: Shenwei Wang <shenwei.wang@nxp.com>; Rob Herring > <robh+dt@kernel.org>; Krzysztof Kozlowski > <krzysztof.kozlowski+dt@linaro.org>; Shawn Guo <shawnguo@kernel.org>; > Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team > <kernel@pengutronix.de>; Peng Fan <peng.fan@nxp.com> > Cc: devicetree@vger.kernel.org; dl-linux-imx <linux-imx@nxp.com> > Subject: Re: [EXT] Re: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support > > Caution: EXT Email > > On 08/08/2022 21:16, Shenwei Wang wrote: > >> On 05/08/2022 18:22, Shenwei Wang wrote: > >>> A kind ping. 😊 > >>> > >>> > >> > >> To whom? What do you need from me? > >> > > > > This the version 5 of the series of patches, and should have addressed all those > comments from you and other reviewers. The other two commits were acked by > you and Rob. This one hasn't gotten any feedback or ack so far. I would greatly > appreciate it if you or Rob could ack it or let me know where to improve. > > This is not a DT bindings patch. Why do you need or expect my ack? > > Best regards, > Krzysztof ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [EXT] Re: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support @ 2022-08-09 16:41 ` Shenwei Wang 0 siblings, 0 replies; 12+ messages in thread From: Shenwei Wang @ 2022-08-09 16:41 UTC (permalink / raw) To: Krzysztof Kozlowski, Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, dl-linux-imx, linux-arm-kernel, imx Hi Shawn, Any comments regarding this patch? Thanks, Shenwei > -----Original Message----- > From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > Sent: Monday, August 8, 2022 11:16 PM > To: Shenwei Wang <shenwei.wang@nxp.com>; Rob Herring > <robh+dt@kernel.org>; Krzysztof Kozlowski > <krzysztof.kozlowski+dt@linaro.org>; Shawn Guo <shawnguo@kernel.org>; > Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team > <kernel@pengutronix.de>; Peng Fan <peng.fan@nxp.com> > Cc: devicetree@vger.kernel.org; dl-linux-imx <linux-imx@nxp.com> > Subject: Re: [EXT] Re: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support > > Caution: EXT Email > > On 08/08/2022 21:16, Shenwei Wang wrote: > >> On 05/08/2022 18:22, Shenwei Wang wrote: > >>> A kind ping. 😊 > >>> > >>> > >> > >> To whom? What do you need from me? > >> > > > > This the version 5 of the series of patches, and should have addressed all those > comments from you and other reviewers. The other two commits were acked by > you and Rob. This one hasn't gotten any feedback or ack so far. I would greatly > appreciate it if you or Rob could ack it or let me know where to improve. > > This is not a DT bindings patch. Why do you need or expect my ack? > > Best regards, > Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support 2022-08-05 16:22 ` Shenwei Wang 2022-08-08 5:47 ` Krzysztof Kozlowski @ 2022-08-18 12:08 ` Shenwei Wang 1 sibling, 0 replies; 12+ messages in thread From: Shenwei Wang @ 2022-08-18 12:08 UTC (permalink / raw) To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Peng Fan Cc: devicetree, dl-linux-imx, imx A gentle ping to Shawn. Regards, Shenwei > -----Original Message----- > From: Shenwei Wang <shenwei.wang@nxp.com> > Sent: Friday, August 5, 2022 11:23 AM > To: Rob Herring <robh+dt@kernel.org>; Krzysztof Kozlowski > <krzysztof.kozlowski+dt@linaro.org>; Shawn Guo <shawnguo@kernel.org>; > Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team > <kernel@pengutronix.de>; Peng Fan <peng.fan@nxp.com> > Cc: devicetree@vger.kernel.org; dl-linux-imx <linux-imx@nxp.com> > Subject: RE: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support > > A kind ping. 😊 > > Regards, > Shenwei > > > -----Original Message----- > > From: Shenwei Wang <shenwei.wang@nxp.com> > > Sent: Monday, August 1, 2022 3:01 PM > > To: Rob Herring <robh+dt@kernel.org>; Krzysztof Kozlowski > > <krzysztof.kozlowski+dt@linaro.org>; Shawn Guo <shawnguo@kernel.org>; > > Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team > > <kernel@pengutronix.de>; Peng Fan <peng.fan@nxp.com> > > Cc: devicetree@vger.kernel.org; dl-linux-imx <linux-imx@nxp.com>; > > Shenwei Wang <shenwei.wang@nxp.com> > > Subject: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support > > > > i.MX8DXL is a device targeting the automotive and industrial market segments. > > The chip is designed to achieve both high performance and low power > > consumption. It has a dual (2x) Cortex-A35 processor. > > > > This patch adds the imx8dxl soc and EVK board support. > > > > Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> > > --- > > arch/arm64/boot/dts/freescale/Makefile | 1 + > > .../arm64/boot/dts/freescale/imx8-ss-ddr.dtsi | 2 +- > > .../arm64/boot/dts/freescale/imx8-ss-dma.dtsi | 138 ++++++ > > .../boot/dts/freescale/imx8-ss-lsio.dtsi | 14 + > > arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 463 ++++++++++++++++++ > > .../boot/dts/freescale/imx8dxl-ss-adma.dtsi | 72 +++ > > .../boot/dts/freescale/imx8dxl-ss-conn.dtsi | 145 ++++++ > > .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi | 9 + > > .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi | 78 +++ > > arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 238 +++++++++ > > 10 files changed, 1159 insertions(+), 1 deletion(-) create mode > > 100644 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > > > diff --git a/arch/arm64/boot/dts/freescale/Makefile > > b/arch/arm64/boot/dts/freescale/Makefile > > index 8bf7f7ecebaa1..2741205efe84e 100644 > > --- a/arch/arm64/boot/dts/freescale/Makefile > > +++ b/arch/arm64/boot/dts/freescale/Makefile > > @@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds- > > 85bb.dtb > > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-899b.dtb > > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb > > > > +dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb > > dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb > > dtb-$(CONFIG_ARCH_MXC) += imx8mm-data-modul-edm-sbc.dtb > > dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb diff --git > > a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > > b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > > index 8b5cad4e27002..7d5183c6c5bef 100644 > > --- a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > > @@ -10,7 +10,7 @@ ddr_subsys: bus@5c000000 { > > #size-cells = <1>; > > ranges = <0x5c000000 0x0 0x5c000000 0x1000000>; > > > > - ddr-pmu@5c020000 { > > + ddr_pmu0: ddr-pmu@5c020000 { > > compatible = "fsl,imx8-ddr-pmu"; > > reg = <0x5c020000 0x10000>; > > interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; diff --git > > a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > > b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > > index 960a802b8b6ee..3944dfbdb7c9e 100644 > > --- a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > > @@ -60,6 +60,54 @@ lpuart3: serial@5a090000 { > > status = "disabled"; > > }; > > > > + spi0_lpcg: clock-controller@5a400000 { > > + compatible = "fsl,imx8qxp-lpcg"; > > + reg = <0x5a400000 0x10000>; > > + #clock-cells = <1>; > > + clocks = <&clk IMX_SC_R_SPI_0 IMX_SC_PM_CLK_PER>, > > + <&dma_ipg_clk>; > > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > > + clock-output-names = "spi0_lpcg_clk", > > + "spi0_lpcg_ipg_clk"; > > + power-domains = <&pd IMX_SC_R_SPI_0>; > > + }; > > + > > + spi1_lpcg: clock-controller@5a410000 { > > + compatible = "fsl,imx8qxp-lpcg"; > > + reg = <0x5a410000 0x10000>; > > + #clock-cells = <1>; > > + clocks = <&clk IMX_SC_R_SPI_1 IMX_SC_PM_CLK_PER>, > > + <&dma_ipg_clk>; > > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > > + clock-output-names = "spi1_lpcg_clk", > > + "spi1_lpcg_ipg_clk"; > > + power-domains = <&pd IMX_SC_R_SPI_1>; > > + }; > > + > > + spi2_lpcg: clock-controller@5a420000 { > > + compatible = "fsl,imx8qxp-lpcg"; > > + reg = <0x5a420000 0x10000>; > > + #clock-cells = <1>; > > + clocks = <&clk IMX_SC_R_SPI_2 IMX_SC_PM_CLK_PER>, > > + <&dma_ipg_clk>; > > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > > + clock-output-names = "spi2_lpcg_clk", > > + "spi2_lpcg_ipg_clk"; > > + power-domains = <&pd IMX_SC_R_SPI_2>; > > + }; > > + > > + spi3_lpcg: clock-controller@5a430000 { > > + compatible = "fsl,imx8qxp-lpcg"; > > + reg = <0x5a430000 0x10000>; > > + #clock-cells = <1>; > > + clocks = <&clk IMX_SC_R_SPI_3 IMX_SC_PM_CLK_PER>, > > + <&dma_ipg_clk>; > > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > > + clock-output-names = "spi3_lpcg_clk", > > + "spi3_lpcg_ipg_clk"; > > + power-domains = <&pd IMX_SC_R_SPI_3>; > > + }; > > + > > uart0_lpcg: clock-controller@5a460000 { > > compatible = "fsl,imx8qxp-lpcg"; > > reg = <0x5a460000 0x10000>; > > @@ -108,6 +156,18 @@ uart3_lpcg: clock-controller@5a490000 { > > power-domains = <&pd IMX_SC_R_UART_3>; > > }; > > > > + emvsim0_lpcg: clock-controller@5a4d0000 { > > + compatible = "fsl,imx8qxp-lpcg"; > > + reg = <0x5a4d0000 0x10000>; > > + #clock-cells = <1>; > > + clocks = <&clk IMX_SC_R_EMVSIM_0 IMX_SC_PM_CLK_PER>, > > + <&dma_ipg_clk>; > > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > > + clock-output-names = "emvsim0_lpcg_clk", > > + "emvsim0_lpcg_ipg_clk"; > > + power-domains = <&pd IMX_SC_R_EMVSIM_0>; > > + }; > > + > > i2c0: i2c@5a800000 { > > reg = <0x5a800000 0x4000>; > > interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; @@ -199,4 > > +259,82 @@ i2c3_lpcg: clock-controller@5ac30000 { > > "i2c3_lpcg_ipg_clk"; > > power-domains = <&pd IMX_SC_R_I2C_3>; > > }; > > + > > + lpspi0: spi@5a000000 { > > + compatible = "fsl,imx7ulp-spi"; > > + reg = <0x5a000000 0x10000>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + interrupts = <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-parent = <&gic>; > > + clocks = <&spi0_lpcg IMX_LPCG_CLK_0>, > > + <&spi0_lpcg IMX_LPCG_CLK_4>; > > + clock-names = "per", "ipg"; > > + assigned-clocks = <&clk IMX_SC_R_SPI_0 > > IMX_SC_PM_CLK_PER>; > > + assigned-clock-rates = <20000000>; > > + power-domains = <&pd IMX_SC_R_SPI_0>; > > + status = "disabled"; > > + }; > > + > > + lpspi1: spi@5a010000 { > > + compatible = "fsl,imx7ulp-spi"; > > + reg = <0x5a010000 0x10000>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + interrupts = <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-parent = <&gic>; > > + clocks = <&spi1_lpcg IMX_LPCG_CLK_0>, > > + <&spi1_lpcg IMX_LPCG_CLK_4>; > > + clock-names = "per", "ipg"; > > + assigned-clocks = <&clk IMX_SC_R_SPI_1 > > IMX_SC_PM_CLK_PER>; > > + assigned-clock-rates = <60000000>; > > + power-domains = <&pd IMX_SC_R_SPI_1>; > > + status = "disabled"; > > + }; > > + > > + lpspi2: spi@5a020000 { > > + compatible = "fsl,imx7ulp-spi"; > > + reg = <0x5a020000 0x10000>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-parent = <&gic>; > > + clocks = <&spi2_lpcg IMX_LPCG_CLK_0>, > > + <&spi2_lpcg IMX_LPCG_CLK_4>; > > + clock-names = "per", "ipg"; > > + assigned-clocks = <&clk IMX_SC_R_SPI_2 > > IMX_SC_PM_CLK_PER>; > > + assigned-clock-rates = <60000000>; > > + power-domains = <&pd IMX_SC_R_SPI_2>; > > + status = "disabled"; > > + }; > > + > > + lpspi3: spi@5a030000 { > > + compatible = "fsl,imx7ulp-spi"; > > + reg = <0x5a030000 0x10000>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + interrupts = <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-parent = <&gic>; > > + clocks = <&spi3_lpcg IMX_LPCG_CLK_0>, > > + <&spi3_lpcg IMX_LPCG_CLK_4>; > > + clock-names = "per", "ipg"; > > + assigned-clocks = <&clk IMX_SC_R_SPI_3 > > IMX_SC_PM_CLK_PER>; > > + assigned-clock-rates = <60000000>; > > + power-domains = <&pd IMX_SC_R_SPI_3>; > > + status = "disabled"; > > + }; > > + > > + can0_lpcg: clock-controller@5acd0000 { > > + compatible = "fsl,imx8qxp-lpcg"; > > + reg = <0x5acd0000 0x10000>; > > + #clock-cells = <1>; > > + clocks = <&clk IMX_SC_R_CAN_0 IMX_SC_PM_CLK_PER>, > > + <&dma_ipg_clk>, <&dma_ipg_clk>; > > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>, > > + <IMX_LPCG_CLK_5>; > > + clock-output-names = "can0_lpcg_pe_clk", > > + "can0_lpcg_ipg_clk", > > + "can0_lpcg_chi_clk"; > > + power-domains = <&pd IMX_SC_R_CAN_0>; > > + }; > > }; > > diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > > b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > > index 6446e6df7a9ac..61c506b0c1456 100644 > > --- a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > > @@ -107,6 +107,20 @@ lsio_gpio7: gpio@5d0f0000 { > > power-domains = <&pd IMX_SC_R_GPIO_7>; > > }; > > > > + flexspi0: spi@5d120000 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + compatible = "nxp,imx8qxp-fspi"; > > + reg = <0x5d120000 0x10000>, <0x08000000 0x10000000>; > > + reg-names = "fspi_base", "fspi_mmap"; > > + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clk IMX_SC_R_FSPI_0 IMX_SC_PM_CLK_PER>, > > + <&clk IMX_SC_R_FSPI_0 IMX_SC_PM_CLK_PER>; > > + clock-names = "fspi", "fspi_en"; > > + power-domains = <&pd IMX_SC_R_FSPI_0>; > > + status = "disabled"; > > + }; > > + > > lsio_mu0: mailbox@5d1b0000 { > > reg = <0x5d1b0000 0x10000>; > > interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; diff --git > > a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > > b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > > new file mode 100644 > > index 0000000000000..052a30182eb4e > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > > @@ -0,0 +1,463 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Copyright 2019~2020, 2022 NXP > > + */ > > + > > +/dts-v1/; > > + > > +#include "imx8dxl.dtsi" > > + > > +/ { > > + model = "Freescale i.MX8DXL EVK"; > > + compatible = "fsl,imx8dxl-evk", "fsl,imx8dxl"; > > + > > + aliases { > > + i2c2 = &i2c2; > > + mmc0 = &usdhc1; > > + mmc1 = &usdhc2; > > + serial0 = &lpuart0; > > + }; > > + > > + chosen { > > + stdout-path = &lpuart0; > > + }; > > + > > + memory@80000000 { > > + device_type = "memory"; > > + reg = <0x00000000 0x80000000 0 0x40000000>; > > + }; > > + > > + reserved-memory { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + > > + /* > > + * Memory reserved for optee usage. Please do not use. > > + * This will be automatically added to dtb if OP-TEE is installed. > > + * optee@96000000 { > > + * reg = <0 0x96000000 0 0x2000000>; > > + * no-map; > > + * }; > > + */ > > + > > + /* global autoconfigured region for contiguous allocations */ > > + linux,cma { > > + compatible = "shared-dma-pool"; > > + reusable; > > + size = <0 0x14000000>; > > + alloc-ranges = <0 0x98000000 0 0x14000000>; > > + linux,cma-default; > > + }; > > + }; > > + > > + mux3_en: regulator-0 { > > + compatible = "regulator-fixed"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "mux3_en"; > > + gpio = <&pca6416_2 8 GPIO_ACTIVE_LOW>; > > + regulator-always-on; > > + }; > > + > > + reg_fec1_sel: regulator-1 { > > + compatible = "regulator-fixed"; > > + regulator-name = "fec1_supply"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + gpio = <&pca6416_1 11 GPIO_ACTIVE_HIGH>; > > + regulator-always-on; > > + status = "disabled"; > > + }; > > + > > + reg_fec1_io: regulator-2 { > > + compatible = "regulator-fixed"; > > + regulator-name = "fec1_io_supply"; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + gpio = <&max7322 0 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + regulator-always-on; > > + status = "disabled"; > > + }; > > + > > + reg_usdhc2_vmmc: regulator-3 { > > + compatible = "regulator-fixed"; > > + regulator-name = "SD1_SPWR"; > > + regulator-min-microvolt = <3000000>; > > + regulator-max-microvolt = <3000000>; > > + gpio = <&lsio_gpio4 30 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + off-on-delay-us = <3480>; > > + }; > > +}; > > + > > +&eqos { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_eqos>; > > + phy-mode = "rgmii-id"; > > + phy-handle = <ðphy0>; > > + nvmem-cells = <&fec_mac1>; > > + nvmem-cell-names = "mac-address"; > > + snps,reset-gpios = <&pca6416_1 2 GPIO_ACTIVE_LOW>; > > + snps,reset-delays-us = <10 20 200000>; > > + status = "okay"; > > + > > + mdio { > > + compatible = "snps,dwmac-mdio"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + ethphy0: ethernet-phy@0 { > > + compatible = "ethernet-phy-ieee802.3-c22"; > > + reg = <0>; > > + eee-broken-1000t; > > + qca,disable-smarteee; > > + vddio-supply = <&vddio0>; > > + > > + vddio0: vddio-regulator { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + }; > > + }; > > + }; > > +}; > > + > > +/* > > + * fec1 shares the some PINs with usdhc2. > > + * by default usdhc2 is enabled in this dts. > > + * Please disable usdhc2 to enable fec1 */ > > +&fec1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_fec1>; > > + phy-mode = "rgmii-txid"; > > + phy-handle = <ðphy1>; > > + fsl,magic-packet; > > + rx-internal-delay-ps = <2000>; > > + nvmem-cells = <&fec_mac0>; > > + nvmem-cell-names = "mac-address"; > > + phy-reset-gpios = <&pca6416_1 0 GPIO_ACTIVE_LOW>; > > + phy-reset-duration = <10>; > > + phy-reset-post-delay = <150>; > > + status = "disabled"; > > + > > + mdio { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + ethphy1: ethernet-phy@1 { > > + compatible = "ethernet-phy-ieee802.3-c22"; > > + reg = <1>; > > + qca,disable-smarteee; > > + vddio-supply = <&vddio1>; > > + > > + vddio1: vddio-regulator { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + }; > > + }; > > + }; > > +}; > > + > > +&flexspi0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_flexspi0>; > > + nxp,fspi-dll-slvdly = <4>; > > + status = "okay"; > > + > > + mt35xu512aba0: flash@0 { > > + compatible = "jedec,spi-nor"; > > + reg = <0>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + spi-max-frequency = <133000000>; > > + spi-tx-bus-width = <8>; > > + spi-rx-bus-width = <8>; > > + }; > > +}; > > + > > +&i2c2 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + clock-frequency = <100000>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_i2c2>; > > + status = "okay"; > > + > > + pca6416_1: gpio@20 { > > + compatible = "ti,tca6416"; > > + reg = <0x20>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + }; > > + > > + pca6416_2: gpio@21 { > > + compatible = "ti,tca6416"; > > + reg = <0x21>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + }; > > + > > + pca9548_1: i2c-mux@70 { > > + compatible = "nxp,pca9548"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x70>; > > + > > + i2c@0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x0>; > > + > > + max7322: gpio@68 { > > + compatible = "maxim,max7322"; > > + reg = <0x68>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + status = "disabled"; > > + }; > > + }; > > + > > + i2c@4 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x4>; > > + }; > > + > > + i2c@5 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x5>; > > + }; > > + > > + i2c@6 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x6>; > > + }; > > + }; > > +}; > > + > > +&lpuart0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_lpuart0>; > > + status = "okay"; > > +}; > > + > > +&lsio_gpio4 { > > + status = "okay"; > > +}; > > + > > +&lsio_gpio5 { > > + status = "okay"; > > +}; > > + > > +&thermal_zones { > > + pmic-thermal0 { > > + polling-delay-passive = <250>; > > + polling-delay = <2000>; > > + thermal-sensors = <&tsens IMX_SC_R_PMIC_0>; > > + > > + trips { > > + pmic_alert0: trip0 { > > + temperature = <110000>; > > + hysteresis = <2000>; > > + type = "passive"; > > + }; > > + pmic_crit0: trip1 { > > + temperature = <125000>; > > + hysteresis = <2000>; > > + type = "critical"; > > + }; > > + }; > > + > > + cooling-maps { > > + map0 { > > + trip = <&pmic_alert0>; > > + cooling-device = > > + <&A35_0 THERMAL_NO_LIMIT > > THERMAL_NO_LIMIT>, > > + <&A35_1 THERMAL_NO_LIMIT > > THERMAL_NO_LIMIT>; > > + }; > > + }; > > + }; > > +}; > > + > > +&usdhc1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usdhc1>; > > + bus-width = <8>; > > + no-sd; > > + no-sdio; > > + non-removable; > > + status = "okay"; > > +}; > > + > > +&usdhc2 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; > > + bus-width = <4>; > > + vmmc-supply = <®_usdhc2_vmmc>; > > + cd-gpios = <&lsio_gpio5 1 GPIO_ACTIVE_LOW>; > > + wp-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>; > > + max-frequency = <100000000>; > > + status = "okay"; > > +}; > > + > > +&iomuxc { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_hog>; > > + > > + pinctrl_hog: hoggrp { > > + fsl,pins = < > > + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD > > 0x000514a0 > > + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHK_PAD > > 0x000014a0 > > + IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1 > > 0x0600004c > > + IMX8DXL_SNVS_TAMPER_OUT1_LSIO_GPIO2_IO05_IN > > 0x0600004c > > + >; > > + }; > > + > > + pinctrl_usbotg1: usbotg1grp { > > + fsl,pins = < > > + IMX8DXL_USB_SS3_TC0_CONN_USB_OTG1_PWR > > 0x00000021 > > + >; > > + }; > > + > > + pinctrl_usbotg2: usbotg2grp { > > + fsl,pins = < > > + IMX8DXL_USB_SS3_TC1_CONN_USB_OTG2_PWR > > 0x00000021 > > + >; > > + }; > > + > > + pinctrl_eqos: eqosgrp { > > + fsl,pins = < > > + IMX8DXL_ENET0_MDC_CONN_EQOS_MDC > > 0x06000020 > > + IMX8DXL_ENET0_MDIO_CONN_EQOS_MDIO > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_TX_CTL_CONN_EQOS_RGMII_TX_CTL > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_TXC_CONN_EQOS_RGMII_TXC > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_TXD0_CONN_EQOS_RGMII_TXD0 > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_TXD1_CONN_EQOS_RGMII_TXD1 > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_TXD2_CONN_EQOS_RGMII_TXD2 > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_TXD3_CONN_EQOS_RGMII_TXD3 > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_RXC_CONN_EQOS_RGMII_RXC > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_RX_CTL_CONN_EQOS_RGMII_RX_CTL > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_RXD0_CONN_EQOS_RGMII_RXD0 > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_RXD1_CONN_EQOS_RGMII_RXD1 > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_RXD2_CONN_EQOS_RGMII_RXD2 > > 0x06000020 > > + > > IMX8DXL_ENET1_RGMII_RXD3_CONN_EQOS_RGMII_RXD3 > > 0x06000020 > > + >; > > + }; > > + > > + pinctrl_flexspi0: flexspi0grp { > > + fsl,pins = < > > + IMX8DXL_QSPI0A_DATA0_LSIO_QSPI0A_DATA0 > > 0x06000021 > > + IMX8DXL_QSPI0A_DATA1_LSIO_QSPI0A_DATA1 > > 0x06000021 > > + IMX8DXL_QSPI0A_DATA2_LSIO_QSPI0A_DATA2 > > 0x06000021 > > + IMX8DXL_QSPI0A_DATA3_LSIO_QSPI0A_DATA3 > > 0x06000021 > > + IMX8DXL_QSPI0A_DQS_LSIO_QSPI0A_DQS > > 0x06000021 > > + IMX8DXL_QSPI0A_SS0_B_LSIO_QSPI0A_SS0_B > > 0x06000021 > > + IMX8DXL_QSPI0A_SCLK_LSIO_QSPI0A_SCLK > > 0x06000021 > > + IMX8DXL_QSPI0B_SCLK_LSIO_QSPI0B_SCLK > > 0x06000021 > > + IMX8DXL_QSPI0B_DATA0_LSIO_QSPI0B_DATA0 > > 0x06000021 > > + IMX8DXL_QSPI0B_DATA1_LSIO_QSPI0B_DATA1 > > 0x06000021 > > + IMX8DXL_QSPI0B_DATA2_LSIO_QSPI0B_DATA2 > > 0x06000021 > > + IMX8DXL_QSPI0B_DATA3_LSIO_QSPI0B_DATA3 > > 0x06000021 > > + IMX8DXL_QSPI0B_DQS_LSIO_QSPI0B_DQS > > 0x06000021 > > + IMX8DXL_QSPI0B_SS0_B_LSIO_QSPI0B_SS0_B > > 0x06000021 > > + >; > > + }; > > + > > + pinctrl_fec1: fec1grp { > > + fsl,pins = < > > + > > IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD > > 0x000014a0 > > + > > IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD > > 0x000014a0 > > + IMX8DXL_ENET0_MDC_CONN_ENET0_MDC > > 0x06000020 > > + IMX8DXL_ENET0_MDIO_CONN_ENET0_MDIO > > 0x06000020 > > + > > IMX8DXL_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 > > 0x00000060 > > + > > IMX8DXL_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 > > 0x00000060 > > + >; > > + }; > > + > > + pinctrl_lpspi3: lpspi3grp { > > + fsl,pins = < > > + IMX8DXL_SPI3_SCK_ADMA_SPI3_SCK > > 0x6000040 > > + IMX8DXL_SPI3_SDO_ADMA_SPI3_SDO > > 0x6000040 > > + IMX8DXL_SPI3_SDI_ADMA_SPI3_SDI > > 0x6000040 > > + IMX8DXL_SPI3_CS1_ADMA_SPI3_CS1 > > 0x6000040 > > + >; > > + }; > > + > > + pinctrl_i2c2: i2c2grp { > > + fsl,pins = < > > + IMX8DXL_SPI1_SCK_ADMA_I2C2_SDA > > 0x06000021 > > + IMX8DXL_SPI1_SDO_ADMA_I2C2_SCL > > 0x06000021 > > + >; > > + }; > > + > > + pinctrl_cm40_lpuart: cm40lpuartgrp { > > + fsl,pins = < > > + IMX8DXL_ADC_IN2_M40_UART0_RX > > 0x06000020 > > + IMX8DXL_ADC_IN3_M40_UART0_TX > > 0x06000020 > > + >; > > + }; > > + > > + pinctrl_i2c3: i2c3grp { > > + fsl,pins = < > > + IMX8DXL_SPI1_CS0_ADMA_I2C3_SDA > > 0x06000021 > > + IMX8DXL_SPI1_SDI_ADMA_I2C3_SCL > > 0x06000021 > > + >; > > + }; > > + > > + pinctrl_lpuart0: lpuart0grp { > > + fsl,pins = < > > + IMX8DXL_UART0_RX_ADMA_UART0_RX > > 0x06000020 > > + IMX8DXL_UART0_TX_ADMA_UART0_TX > > 0x06000020 > > + >; > > + }; > > + > > + pinctrl_usdhc1: usdhc1grp { > > + fsl,pins = < > > + IMX8DXL_EMMC0_CLK_CONN_EMMC0_CLK > > 0x06000041 > > + IMX8DXL_EMMC0_CMD_CONN_EMMC0_CMD > > 0x00000021 > > + IMX8DXL_EMMC0_DATA0_CONN_EMMC0_DATA0 > > 0x00000021 > > + IMX8DXL_EMMC0_DATA1_CONN_EMMC0_DATA1 > > 0x00000021 > > + IMX8DXL_EMMC0_DATA2_CONN_EMMC0_DATA2 > > 0x00000021 > > + IMX8DXL_EMMC0_DATA3_CONN_EMMC0_DATA3 > > 0x00000021 > > + IMX8DXL_EMMC0_DATA4_CONN_EMMC0_DATA4 > > 0x00000021 > > + IMX8DXL_EMMC0_DATA5_CONN_EMMC0_DATA5 > > 0x00000021 > > + IMX8DXL_EMMC0_DATA6_CONN_EMMC0_DATA6 > > 0x00000021 > > + IMX8DXL_EMMC0_DATA7_CONN_EMMC0_DATA7 > > 0x00000021 > > + IMX8DXL_EMMC0_STROBE_CONN_EMMC0_STROBE > > 0x00000041 > > + >; > > + }; > > + > > + pinctrl_usdhc2_gpio: usdhc2gpiogrp { > > + fsl,pins = < > > + IMX8DXL_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30 > > 0x00000040 /* RESET_B */ > > + IMX8DXL_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00 > > 0x00000021 /* WP */ > > + IMX8DXL_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01 > > 0x00000021 /* CD */ > > + >; > > + }; > > + > > + pinctrl_usdhc2: usdhc2grp { > > + fsl,pins = < > > + IMX8DXL_ENET0_RGMII_RXC_CONN_USDHC1_CLK > > 0x06000041 > > + > > IMX8DXL_ENET0_RGMII_RX_CTL_CONN_USDHC1_CMD 0x00000021 > > + > > IMX8DXL_ENET0_RGMII_RXD0_CONN_USDHC1_DATA0 0x00000021 > > + > > IMX8DXL_ENET0_RGMII_RXD1_CONN_USDHC1_DATA1 0x00000021 > > + > > IMX8DXL_ENET0_RGMII_RXD2_CONN_USDHC1_DATA2 0x00000021 > > + > > IMX8DXL_ENET0_RGMII_RXD3_CONN_USDHC1_DATA3 0x00000021 > > + > > IMX8DXL_ENET0_RGMII_TXD0_CONN_USDHC1_VSELECT > > 0x00000021 > > + >; > > + }; > > +}; > > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > > b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > > new file mode 100644 > > index 0000000000000..e26bbbf7f1508 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > > @@ -0,0 +1,72 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Copyright 2019~2020, 2022 NXP > > + */ > > + > > +&audio_ipg_clk { > > + clock-frequency = <160000000>; > > +}; > > + > > +&dma_ipg_clk { > > + clock-frequency = <160000000>; > > +}; > > + > > +&i2c0 { > > + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > > + interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&i2c1 { > > + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > > + interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&i2c2 { > > + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > > + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&i2c3 { > > + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > > + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lpspi0 { > > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > > + interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lpspi1 { > > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > > + interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lpspi2 { > > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > > + interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lpspi3 { > > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > > + interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lpuart0 { > > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > > + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lpuart1 { > > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > > + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lpuart2 { > > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > > + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lpuart3 { > > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > > + interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>; }; > > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > > b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > > new file mode 100644 > > index 0000000000000..98f666cbe63bf > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > > @@ -0,0 +1,145 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Copyright 2019~2020, 2022 NXP > > + */ > > + > > +/delete-node/ &enet1_lpcg; > > +/delete-node/ &fec2; > > + > > +&conn_subsys { > > + conn_enet0_root_clk: clock-conn-enet0-root { > > + compatible = "fixed-clock"; > > + #clock-cells = <0>; > > + clock-frequency = <250000000>; > > + clock-output-names = "conn_enet0_root_clk"; > > + }; > > + > > + eqos: ethernet@5b050000 { > > + compatible = "nxp,imx8dxl-dwmac-eqos", "snps,dwmac-5.10a"; > > + reg = <0x5b050000 0x10000>; > > + interrupt-parent = <&gic>; > > + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "eth_wake_irq", "macirq"; > > + clocks = <&eqos_lpcg IMX_LPCG_CLK_4>, > > + <&eqos_lpcg IMX_LPCG_CLK_6>, > > + <&eqos_lpcg IMX_LPCG_CLK_0>, > > + <&eqos_lpcg IMX_LPCG_CLK_5>, > > + <&eqos_lpcg IMX_LPCG_CLK_2>; > > + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "mem"; > > + assigned-clocks = <&clk IMX_SC_R_ENET_1 > > IMX_SC_PM_CLK_PER>; > > + assigned-clock-rates = <125000000>; > > + power-domains = <&pd IMX_SC_R_ENET_1>; > > + clk_csr = <0>; > > + status = "disabled"; > > + }; > > + > > + usbotg2: usb@5b0e0000 { > > + compatible = "fsl,imx8dxl-usb", "fsl,imx7ulp-usb"; > > + reg = <0x5b0e0000 0x200>; > > + interrupt-parent = <&gic>; > > + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; > > + fsl,usbphy = <&usbphy2>; > > + fsl,usbmisc = <&usbmisc2 0>; > > + /* > > + * usbotg1 and usbotg2 share one clcok. > > + * scu firmware disables the access to the clock and keeps > > + * it always on in case other core (M4) uses one of these. > > + */ > > + clocks = <&clk_dummy>; > > + ahb-burst-config = <0x0>; > > + tx-burst-size-dword = <0x10>; > > + rx-burst-size-dword = <0x10>; > > + #stream-id-cells = <1>; > > + power-domains = <&pd IMX_SC_R_USB_1>; > > + status = "disabled"; > > + > > + clk_dummy: clock-dummy { > > + compatible = "fixed-clock"; > > + #clock-cells = <0>; > > + clock-frequency = <0>; > > + clock-output-names = "clk_dummy"; > > + }; > > + }; > > + > > + usbmisc2: usbmisc@5b0e0200 { > > + #index-cells = <1>; > > + compatible = "fsl,imx7ulp-usbmisc"; > > + reg = <0x5b0e0200 0x200>; > > + }; > > + > > + usbphy2: usbphy@0x5b110000 { > > + compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy"; > > + reg = <0x5b110000 0x1000>; > > + clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>; > > + power-domains = <&pd IMX_SC_R_USB_1_PHY>; > > + status = "disabled"; > > + }; > > + > > + eqos_lpcg: clock-controller@5b240000 { > > + compatible = "fsl,imx8qxp-lpcg"; > > + reg = <0x5b240000 0x10000>; > > + #clock-cells = <1>; > > + > > + clocks = <&conn_enet0_root_clk>, > > + <&conn_axi_clk>, > > + <&conn_axi_clk>, > > + <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>, > > + <&conn_ipg_clk>; > > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>, > > + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, > > + <IMX_LPCG_CLK_6>; > > + clock-output-names = "eqos_ptp", > > + "eqos_mem_clk", > > + "eqos_aclk", > > + "eqos_clk", > > + "eqos_csr_clk"; > > + power-domains = <&pd IMX_SC_R_ENET_1>; > > + }; > > + > > + usb2_2_lpcg: clock-controller@5b280000 { > > + compatible = "fsl,imx8qxp-lpcg"; > > + reg = <0x5b280000 0x10000>; > > + #clock-cells = <1>; > > + > > + clock-indices = <IMX_LPCG_CLK_7>; > > + clocks = <&conn_ipg_clk>; > > + clock-output-names = "usboh3_2_phy_ipg_clk"; > > + power-domains = <&pd IMX_SC_R_USB_1_PHY>; > > + }; > > + > > +}; > > + > > +&enet0_lpcg { > > + clocks = <&conn_enet0_root_clk>, > > + <&conn_enet0_root_clk>, > > + <&conn_axi_clk>, > > + <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>, > > + <&conn_ipg_clk>, > > + <&conn_ipg_clk>; > > +}; > > + > > +&fec1 { > > + compatible = "fsl,imx8qm-fec"; > > + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; > > + assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>; > > + assigned-clock-rates = <125000000>; > > +}; > > + > > +&usdhc1 { > > + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; > > + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&usdhc2 { > > + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; > > + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&usdhc3 { > > + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; > > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; }; > > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > > b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > > new file mode 100644 > > index 0000000000000..550f513708d85 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > > @@ -0,0 +1,9 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Copyright 2020 NXP > > + */ > > + > > +&ddr_pmu0 { > > + compatible = "fsl,imx8-ddr-pmu"; > > + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; }; > > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > > b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > > new file mode 100644 > > index 0000000000000..4aaedb6ce591a > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > > @@ -0,0 +1,78 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Copyright 2019~2020, 2022 NXP > > + */ > > +&flexspi0 { > > + compatible = "nxp,imx8dxl-fspi"; > > + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_gpio0 { > > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > > + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_gpio1 { > > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > > + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_gpio2 { > > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > > + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_gpio3 { > > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > > + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_gpio4 { > > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_gpio5 { > > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_gpio6 { > > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_gpio7 { > > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > > + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_mu0 { > > + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > > + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_mu1 { > > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > > + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_mu2 { > > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > > + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_mu3 { > > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > > + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_mu4 { > > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > > + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; }; > > + > > +&lsio_mu5 { > > + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > > + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; }; > > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > new file mode 100644 > > index 0000000000000..037591fb01a55 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > @@ -0,0 +1,238 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Copyright 2019~2020, 2022 NXP > > + */ > > + > > +#include <dt-bindings/clock/imx8-clock.h> #include > > +<dt-bindings/firmware/imx/rsrc.h> > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > +#include <dt-bindings/input/input.h> > > +#include <dt-bindings/pinctrl/pads-imx8dxl.h> > > +#include <dt-bindings/thermal/thermal.h> > > + > > +/ { > > + interrupt-parent = <&gic>; > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + aliases { > > + ethernet0 = &fec1; > > + ethernet1 = &eqos; > > + gpio0 = &lsio_gpio0; > > + gpio1 = &lsio_gpio1; > > + gpio2 = &lsio_gpio2; > > + gpio3 = &lsio_gpio3; > > + gpio4 = &lsio_gpio4; > > + gpio5 = &lsio_gpio5; > > + gpio6 = &lsio_gpio6; > > + gpio7 = &lsio_gpio7; > > + mu1 = &lsio_mu1; > > + }; > > + > > + cpus: cpus { > > + #address-cells = <2>; > > + #size-cells = <0>; > > + > > + /* We have 1 clusters with 2 Cortex-A35 cores */ > > + A35_0: cpu@0 { > > + device_type = "cpu"; > > + compatible = "arm,cortex-a35"; > > + reg = <0x0 0x0>; > > + enable-method = "psci"; > > + next-level-cache = <&A35_L2>; > > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > > + #cooling-cells = <2>; > > + operating-points-v2 = <&a35_opp_table>; > > + }; > > + > > + A35_1: cpu@1 { > > + device_type = "cpu"; > > + compatible = "arm,cortex-a35"; > > + reg = <0x0 0x1>; > > + enable-method = "psci"; > > + next-level-cache = <&A35_L2>; > > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > > + #cooling-cells = <2>; > > + operating-points-v2 = <&a35_opp_table>; > > + }; > > + > > + A35_L2: l2-cache0 { > > + compatible = "cache"; > > + }; > > + }; > > + > > + a35_opp_table: opp-table { > > + compatible = "operating-points-v2"; > > + opp-shared; > > + > > + opp-900000000 { > > + opp-hz = /bits/ 64 <900000000>; > > + opp-microvolt = <1000000>; > > + clock-latency-ns = <150000>; > > + }; > > + > > + opp-1200000000 { > > + opp-hz = /bits/ 64 <1200000000>; > > + opp-microvolt = <1100000>; > > + clock-latency-ns = <150000>; > > + opp-suspend; > > + }; > > + }; > > + > > + gic: interrupt-controller@51a00000 { > > + compatible = "arm,gic-v3"; > > + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */ > > + <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) > > */ > > + #interrupt-cells = <3>; > > + interrupt-controller; > > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > > + }; > > + > > + reserved-memory { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + > > + dsp_reserved: dsp@92400000 { > > + reg = <0 0x92400000 0 0x2000000>; > > + no-map; > > + }; > > + }; > > + > > + pmu { > > + compatible = "arm,armv8-pmuv3"; > > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; > > + }; > > + > > + psci { > > + compatible = "arm,psci-1.0"; > > + method = "smc"; > > + }; > > + > > + system-controller { > > + compatible = "fsl,imx-scu"; > > + mbox-names = "tx0", > > + "rx0", > > + "gip3"; > > + mboxes = <&lsio_mu1 0 0 > > + &lsio_mu1 1 0 > > + &lsio_mu1 3 3>; > > + > > + pd: power-controller { > > + compatible = "fsl,scu-pd"; > > + #power-domain-cells = <1>; > > + wakeup-irq = <160 163 235 236 237 228 229 230 231 > > 238 > > + 239 240 166 169>; > > + }; > > + > > + clk: clock-controller { > > + compatible = "fsl,imx8dxl-clk", "fsl,scu-clk"; > > + #clock-cells = <2>; > > + clocks = <&xtal32k &xtal24m>; > > + clock-names = "xtal_32KHz", "xtal_24Mhz"; > > + }; > > + > > + iomuxc: pinctrl { > > + compatible = "fsl,imx8dxl-iomuxc"; > > + }; > > + > > + ocotp: ocotp { > > + compatible = "fsl,imx8qxp-scu-ocotp"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + fec_mac0: mac@2c4 { > > + reg = <0x2c4 6>; > > + }; > > + > > + fec_mac1: mac@2c6 { > > + reg = <0x2c6 6>; > > + }; > > + }; > > + > > + rtc: rtc { > > + compatible = "fsl,imx8qxp-sc-rtc"; > > + }; > > + > > + sc_pwrkey: keys { > > + compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key"; > > + linux,keycode = <KEY_POWER>; > > + wakeup-source; > > + }; > > + > > + watchdog { > > + compatible = "fsl,imx-sc-wdt"; > > + timeout-sec = <60>; > > + }; > > + > > + tsens: thermal-sensor { > > + compatible = "fsl,imx-sc-thermal"; > > + #thermal-sensor-cells = <1>; > > + }; > > + }; > > + > > + timer { > > + compatible = "arm,armv8-timer"; > > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical > > Secure */ > > + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical > > Non-Secure */ > > + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ > > + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor > > */ > > + }; > > + > > + thermal_zones: thermal-zones { > > + cpu-thermal0 { > > + polling-delay-passive = <250>; > > + polling-delay = <2000>; > > + thermal-sensors = <&tsens IMX_SC_R_SYSTEM>; > > + > > + trips { > > + cpu_alert0: trip0 { > > + temperature = <107000>; > > + hysteresis = <2000>; > > + type = "passive"; > > + }; > > + cpu_crit0: trip1 { > > + temperature = <127000>; > > + hysteresis = <2000>; > > + type = "critical"; > > + }; > > + }; > > + > > + cooling-maps { > > + map0 { > > + trip = <&cpu_alert0>; > > + cooling-device = > > + <&A35_0 THERMAL_NO_LIMIT > > THERMAL_NO_LIMIT>, > > + <&A35_1 THERMAL_NO_LIMIT > > THERMAL_NO_LIMIT>; > > + }; > > + }; > > + }; > > + }; > > + > > + /* The two values below cannot be changed by the board */ > > + xtal32k: clock-xtal32k { > > + compatible = "fixed-clock"; > > + #clock-cells = <0>; > > + clock-frequency = <32768>; > > + clock-output-names = "xtal_32KHz"; > > + }; > > + > > + xtal24m: clock-xtal24m { > > + compatible = "fixed-clock"; > > + #clock-cells = <0>; > > + clock-frequency = <24000000>; > > + clock-output-names = "xtal_24MHz"; > > + }; > > + > > + /* sorted in register address */ > > + #include "imx8-ss-adma.dtsi" > > + #include "imx8-ss-conn.dtsi" > > + #include "imx8-ss-ddr.dtsi" > > + #include "imx8-ss-lsio.dtsi" > > +}; > > + > > +#include "imx8dxl-ss-adma.dtsi" > > +#include "imx8dxl-ss-conn.dtsi" > > +#include "imx8dxl-ss-lsio.dtsi" > > +#include "imx8dxl-ss-ddr.dtsi" > > -- > > 2.25.1 ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support 2022-08-01 20:01 ` [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support Shenwei Wang 2022-08-05 16:22 ` Shenwei Wang @ 2022-08-21 13:14 ` Shawn Guo 1 sibling, 0 replies; 12+ messages in thread From: Shawn Guo @ 2022-08-21 13:14 UTC (permalink / raw) To: Shenwei Wang Cc: Rob Herring, Krzysztof Kozlowski, Sascha Hauer, Pengutronix Kernel Team, Peng Fan, devicetree, NXP Linux Team On Mon, Aug 01, 2022 at 03:01:21PM -0500, Shenwei Wang wrote: > i.MX8DXL is a device targeting the automotive and industrial market > segments. The chip is designed to achieve both high performance and > low power consumption. It has a dual (2x) Cortex-A35 processor. > > This patch adds the imx8dxl soc and EVK board support. Could you split SoC and board changes into separate patch? > > Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> > --- > arch/arm64/boot/dts/freescale/Makefile | 1 + > .../arm64/boot/dts/freescale/imx8-ss-ddr.dtsi | 2 +- > .../arm64/boot/dts/freescale/imx8-ss-dma.dtsi | 138 ++++++ > .../boot/dts/freescale/imx8-ss-lsio.dtsi | 14 + > arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 463 ++++++++++++++++++ > .../boot/dts/freescale/imx8dxl-ss-adma.dtsi | 72 +++ > .../boot/dts/freescale/imx8dxl-ss-conn.dtsi | 145 ++++++ > .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi | 9 + > .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi | 78 +++ > arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 238 +++++++++ > 10 files changed, 1159 insertions(+), 1 deletion(-) > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile > index 8bf7f7ecebaa1..2741205efe84e 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-85bb.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-899b.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb > > +dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-data-modul-edm-sbc.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb > diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > index 8b5cad4e27002..7d5183c6c5bef 100644 > --- a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi > @@ -10,7 +10,7 @@ ddr_subsys: bus@5c000000 { > #size-cells = <1>; > ranges = <0x5c000000 0x0 0x5c000000 0x1000000>; > > - ddr-pmu@5c020000 { > + ddr_pmu0: ddr-pmu@5c020000 { > compatible = "fsl,imx8-ddr-pmu"; > reg = <0x5c020000 0x10000>; > interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; > diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > index 960a802b8b6ee..3944dfbdb7c9e 100644 > --- a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi > @@ -60,6 +60,54 @@ lpuart3: serial@5a090000 { > status = "disabled"; > }; > > + spi0_lpcg: clock-controller@5a400000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a400000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_SPI_0 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "spi0_lpcg_clk", > + "spi0_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_SPI_0>; > + }; > + > + spi1_lpcg: clock-controller@5a410000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a410000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_SPI_1 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "spi1_lpcg_clk", > + "spi1_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_SPI_1>; > + }; > + > + spi2_lpcg: clock-controller@5a420000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a420000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_SPI_2 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "spi2_lpcg_clk", > + "spi2_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_SPI_2>; > + }; > + > + spi3_lpcg: clock-controller@5a430000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a430000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_SPI_3 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "spi3_lpcg_clk", > + "spi3_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_SPI_3>; > + }; > + > uart0_lpcg: clock-controller@5a460000 { > compatible = "fsl,imx8qxp-lpcg"; > reg = <0x5a460000 0x10000>; > @@ -108,6 +156,18 @@ uart3_lpcg: clock-controller@5a490000 { > power-domains = <&pd IMX_SC_R_UART_3>; > }; > > + emvsim0_lpcg: clock-controller@5a4d0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5a4d0000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_EMVSIM_0 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; > + clock-output-names = "emvsim0_lpcg_clk", > + "emvsim0_lpcg_ipg_clk"; > + power-domains = <&pd IMX_SC_R_EMVSIM_0>; > + }; > + > i2c0: i2c@5a800000 { > reg = <0x5a800000 0x4000>; > interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; > @@ -199,4 +259,82 @@ i2c3_lpcg: clock-controller@5ac30000 { > "i2c3_lpcg_ipg_clk"; > power-domains = <&pd IMX_SC_R_I2C_3>; > }; > + > + lpspi0: spi@5a000000 { > + compatible = "fsl,imx7ulp-spi"; > + reg = <0x5a000000 0x10000>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-parent = <&gic>; > + clocks = <&spi0_lpcg IMX_LPCG_CLK_0>, > + <&spi0_lpcg IMX_LPCG_CLK_4>; > + clock-names = "per", "ipg"; > + assigned-clocks = <&clk IMX_SC_R_SPI_0 IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <20000000>; > + power-domains = <&pd IMX_SC_R_SPI_0>; > + status = "disabled"; > + }; > + > + lpspi1: spi@5a010000 { > + compatible = "fsl,imx7ulp-spi"; > + reg = <0x5a010000 0x10000>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-parent = <&gic>; > + clocks = <&spi1_lpcg IMX_LPCG_CLK_0>, > + <&spi1_lpcg IMX_LPCG_CLK_4>; > + clock-names = "per", "ipg"; > + assigned-clocks = <&clk IMX_SC_R_SPI_1 IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <60000000>; > + power-domains = <&pd IMX_SC_R_SPI_1>; > + status = "disabled"; > + }; > + > + lpspi2: spi@5a020000 { > + compatible = "fsl,imx7ulp-spi"; > + reg = <0x5a020000 0x10000>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-parent = <&gic>; > + clocks = <&spi2_lpcg IMX_LPCG_CLK_0>, > + <&spi2_lpcg IMX_LPCG_CLK_4>; > + clock-names = "per", "ipg"; > + assigned-clocks = <&clk IMX_SC_R_SPI_2 IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <60000000>; > + power-domains = <&pd IMX_SC_R_SPI_2>; > + status = "disabled"; > + }; > + > + lpspi3: spi@5a030000 { > + compatible = "fsl,imx7ulp-spi"; > + reg = <0x5a030000 0x10000>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-parent = <&gic>; > + clocks = <&spi3_lpcg IMX_LPCG_CLK_0>, > + <&spi3_lpcg IMX_LPCG_CLK_4>; > + clock-names = "per", "ipg"; > + assigned-clocks = <&clk IMX_SC_R_SPI_3 IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <60000000>; > + power-domains = <&pd IMX_SC_R_SPI_3>; > + status = "disabled"; > + }; > + > + can0_lpcg: clock-controller@5acd0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5acd0000 0x10000>; > + #clock-cells = <1>; > + clocks = <&clk IMX_SC_R_CAN_0 IMX_SC_PM_CLK_PER>, > + <&dma_ipg_clk>, <&dma_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>, > + <IMX_LPCG_CLK_5>; > + clock-output-names = "can0_lpcg_pe_clk", > + "can0_lpcg_ipg_clk", > + "can0_lpcg_chi_clk"; > + power-domains = <&pd IMX_SC_R_CAN_0>; > + }; > }; > diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > index 6446e6df7a9ac..61c506b0c1456 100644 > --- a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi > @@ -107,6 +107,20 @@ lsio_gpio7: gpio@5d0f0000 { > power-domains = <&pd IMX_SC_R_GPIO_7>; > }; > > + flexspi0: spi@5d120000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "nxp,imx8qxp-fspi"; > + reg = <0x5d120000 0x10000>, <0x08000000 0x10000000>; > + reg-names = "fspi_base", "fspi_mmap"; > + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clk IMX_SC_R_FSPI_0 IMX_SC_PM_CLK_PER>, > + <&clk IMX_SC_R_FSPI_0 IMX_SC_PM_CLK_PER>; > + clock-names = "fspi", "fspi_en"; > + power-domains = <&pd IMX_SC_R_FSPI_0>; > + status = "disabled"; > + }; > + > lsio_mu0: mailbox@5d1b0000 { > reg = <0x5d1b0000 0x10000>; > interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > new file mode 100644 > index 0000000000000..052a30182eb4e > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts > @@ -0,0 +1,463 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > + > +/dts-v1/; > + > +#include "imx8dxl.dtsi" > + > +/ { > + model = "Freescale i.MX8DXL EVK"; > + compatible = "fsl,imx8dxl-evk", "fsl,imx8dxl"; > + > + aliases { > + i2c2 = &i2c2; > + mmc0 = &usdhc1; > + mmc1 = &usdhc2; > + serial0 = &lpuart0; > + }; > + > + chosen { > + stdout-path = &lpuart0; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + reg = <0x00000000 0x80000000 0 0x40000000>; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + /* > + * Memory reserved for optee usage. Please do not use. > + * This will be automatically added to dtb if OP-TEE is installed. > + * optee@96000000 { > + * reg = <0 0x96000000 0 0x2000000>; > + * no-map; > + * }; > + */ > + > + /* global autoconfigured region for contiguous allocations */ > + linux,cma { > + compatible = "shared-dma-pool"; > + reusable; > + size = <0 0x14000000>; > + alloc-ranges = <0 0x98000000 0 0x14000000>; > + linux,cma-default; > + }; > + }; > + > + mux3_en: regulator-0 { > + compatible = "regulator-fixed"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "mux3_en"; > + gpio = <&pca6416_2 8 GPIO_ACTIVE_LOW>; > + regulator-always-on; > + }; > + > + reg_fec1_sel: regulator-1 { > + compatible = "regulator-fixed"; > + regulator-name = "fec1_supply"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&pca6416_1 11 GPIO_ACTIVE_HIGH>; > + regulator-always-on; > + status = "disabled"; > + }; > + > + reg_fec1_io: regulator-2 { > + compatible = "regulator-fixed"; > + regulator-name = "fec1_io_supply"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + gpio = <&max7322 0 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-always-on; > + status = "disabled"; > + }; > + > + reg_usdhc2_vmmc: regulator-3 { > + compatible = "regulator-fixed"; > + regulator-name = "SD1_SPWR"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + gpio = <&lsio_gpio4 30 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + off-on-delay-us = <3480>; > + }; > +}; > + > +&eqos { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_eqos>; > + phy-mode = "rgmii-id"; > + phy-handle = <ðphy0>; > + nvmem-cells = <&fec_mac1>; > + nvmem-cell-names = "mac-address"; > + snps,reset-gpios = <&pca6416_1 2 GPIO_ACTIVE_LOW>; > + snps,reset-delays-us = <10 20 200000>; > + status = "okay"; > + > + mdio { > + compatible = "snps,dwmac-mdio"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy0: ethernet-phy@0 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <0>; > + eee-broken-1000t; > + qca,disable-smarteee; > + vddio-supply = <&vddio0>; > + > + vddio0: vddio-regulator { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + }; > + }; > +}; > + > +/* > + * fec1 shares the some PINs with usdhc2. > + * by default usdhc2 is enabled in this dts. > + * Please disable usdhc2 to enable fec1 > + */ > +&fec1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_fec1>; > + phy-mode = "rgmii-txid"; > + phy-handle = <ðphy1>; > + fsl,magic-packet; > + rx-internal-delay-ps = <2000>; > + nvmem-cells = <&fec_mac0>; > + nvmem-cell-names = "mac-address"; > + phy-reset-gpios = <&pca6416_1 0 GPIO_ACTIVE_LOW>; > + phy-reset-duration = <10>; > + phy-reset-post-delay = <150>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy1: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + qca,disable-smarteee; > + vddio-supply = <&vddio1>; > + > + vddio1: vddio-regulator { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + }; > + }; > +}; > + > +&flexspi0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_flexspi0>; > + nxp,fspi-dll-slvdly = <4>; Is this a supported property? > + status = "okay"; > + > + mt35xu512aba0: flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0>; > + #address-cells = <1>; > + #size-cells = <1>; > + spi-max-frequency = <133000000>; > + spi-tx-bus-width = <8>; > + spi-rx-bus-width = <8>; > + }; > +}; > + > +&i2c2 { > + #address-cells = <1>; > + #size-cells = <0>; > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + pca6416_1: gpio@20 { > + compatible = "ti,tca6416"; > + reg = <0x20>; > + gpio-controller; > + #gpio-cells = <2>; > + }; > + > + pca6416_2: gpio@21 { > + compatible = "ti,tca6416"; > + reg = <0x21>; > + gpio-controller; > + #gpio-cells = <2>; > + }; > + > + pca9548_1: i2c-mux@70 { > + compatible = "nxp,pca9548"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x70>; > + > + i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x0>; > + > + max7322: gpio@68 { > + compatible = "maxim,max7322"; > + reg = <0x68>; > + gpio-controller; > + #gpio-cells = <2>; > + status = "disabled"; > + }; > + }; > + > + i2c@4 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x4>; > + }; > + > + i2c@5 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x5>; > + }; > + > + i2c@6 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x6>; > + }; > + }; > +}; > + > +&lpuart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_lpuart0>; > + status = "okay"; > +}; > + > +&lsio_gpio4 { > + status = "okay"; > +}; > + > +&lsio_gpio5 { > + status = "okay"; > +}; > + > +&thermal_zones { > + pmic-thermal0 { > + polling-delay-passive = <250>; > + polling-delay = <2000>; > + thermal-sensors = <&tsens IMX_SC_R_PMIC_0>; > + > + trips { > + pmic_alert0: trip0 { > + temperature = <110000>; > + hysteresis = <2000>; > + type = "passive"; > + }; Have a newline between nodes. > + pmic_crit0: trip1 { > + temperature = <125000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&pmic_alert0>; > + cooling-device = > + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + }; > + }; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + bus-width = <8>; > + no-sd; > + no-sdio; > + non-removable; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; > + bus-width = <4>; > + vmmc-supply = <®_usdhc2_vmmc>; > + cd-gpios = <&lsio_gpio5 1 GPIO_ACTIVE_LOW>; > + wp-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>; > + max-frequency = <100000000>; Could you have a comment about why you need this property? > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + pinctrl_hog: hoggrp { > + fsl,pins = < > + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD 0x000514a0 > + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHK_PAD 0x000014a0 > + IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1 0x0600004c > + IMX8DXL_SNVS_TAMPER_OUT1_LSIO_GPIO2_IO05_IN 0x0600004c > + >; > + }; > + > + pinctrl_usbotg1: usbotg1grp { > + fsl,pins = < > + IMX8DXL_USB_SS3_TC0_CONN_USB_OTG1_PWR 0x00000021 > + >; > + }; > + > + pinctrl_usbotg2: usbotg2grp { > + fsl,pins = < > + IMX8DXL_USB_SS3_TC1_CONN_USB_OTG2_PWR 0x00000021 > + >; > + }; > + > + pinctrl_eqos: eqosgrp { Could you try to sort these pinctrl nodes alphabetically? > + fsl,pins = < > + IMX8DXL_ENET0_MDC_CONN_EQOS_MDC 0x06000020 > + IMX8DXL_ENET0_MDIO_CONN_EQOS_MDIO 0x06000020 > + IMX8DXL_ENET1_RGMII_TX_CTL_CONN_EQOS_RGMII_TX_CTL 0x06000020 > + IMX8DXL_ENET1_RGMII_TXC_CONN_EQOS_RGMII_TXC 0x06000020 > + IMX8DXL_ENET1_RGMII_TXD0_CONN_EQOS_RGMII_TXD0 0x06000020 > + IMX8DXL_ENET1_RGMII_TXD1_CONN_EQOS_RGMII_TXD1 0x06000020 > + IMX8DXL_ENET1_RGMII_TXD2_CONN_EQOS_RGMII_TXD2 0x06000020 > + IMX8DXL_ENET1_RGMII_TXD3_CONN_EQOS_RGMII_TXD3 0x06000020 > + IMX8DXL_ENET1_RGMII_RXC_CONN_EQOS_RGMII_RXC 0x06000020 > + IMX8DXL_ENET1_RGMII_RX_CTL_CONN_EQOS_RGMII_RX_CTL 0x06000020 > + IMX8DXL_ENET1_RGMII_RXD0_CONN_EQOS_RGMII_RXD0 0x06000020 > + IMX8DXL_ENET1_RGMII_RXD1_CONN_EQOS_RGMII_RXD1 0x06000020 > + IMX8DXL_ENET1_RGMII_RXD2_CONN_EQOS_RGMII_RXD2 0x06000020 > + IMX8DXL_ENET1_RGMII_RXD3_CONN_EQOS_RGMII_RXD3 0x06000020 > + >; > + }; > + > + pinctrl_flexspi0: flexspi0grp { > + fsl,pins = < > + IMX8DXL_QSPI0A_DATA0_LSIO_QSPI0A_DATA0 0x06000021 > + IMX8DXL_QSPI0A_DATA1_LSIO_QSPI0A_DATA1 0x06000021 > + IMX8DXL_QSPI0A_DATA2_LSIO_QSPI0A_DATA2 0x06000021 > + IMX8DXL_QSPI0A_DATA3_LSIO_QSPI0A_DATA3 0x06000021 > + IMX8DXL_QSPI0A_DQS_LSIO_QSPI0A_DQS 0x06000021 > + IMX8DXL_QSPI0A_SS0_B_LSIO_QSPI0A_SS0_B 0x06000021 > + IMX8DXL_QSPI0A_SCLK_LSIO_QSPI0A_SCLK 0x06000021 > + IMX8DXL_QSPI0B_SCLK_LSIO_QSPI0B_SCLK 0x06000021 > + IMX8DXL_QSPI0B_DATA0_LSIO_QSPI0B_DATA0 0x06000021 > + IMX8DXL_QSPI0B_DATA1_LSIO_QSPI0B_DATA1 0x06000021 > + IMX8DXL_QSPI0B_DATA2_LSIO_QSPI0B_DATA2 0x06000021 > + IMX8DXL_QSPI0B_DATA3_LSIO_QSPI0B_DATA3 0x06000021 > + IMX8DXL_QSPI0B_DQS_LSIO_QSPI0B_DQS 0x06000021 > + IMX8DXL_QSPI0B_SS0_B_LSIO_QSPI0B_SS0_B 0x06000021 > + >; > + }; > + > + pinctrl_fec1: fec1grp { > + fsl,pins = < > + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD 0x000014a0 > + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD 0x000014a0 > + IMX8DXL_ENET0_MDC_CONN_ENET0_MDC 0x06000020 > + IMX8DXL_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020 > + IMX8DXL_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x00000060 > + IMX8DXL_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x00000060 > + IMX8DXL_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x00000060 > + IMX8DXL_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x00000060 > + IMX8DXL_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x00000060 > + IMX8DXL_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x00000060 > + IMX8DXL_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x00000060 > + IMX8DXL_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x00000060 > + IMX8DXL_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x00000060 > + IMX8DXL_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x00000060 > + IMX8DXL_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x00000060 > + IMX8DXL_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x00000060 > + >; > + }; > + > + pinctrl_lpspi3: lpspi3grp { > + fsl,pins = < > + IMX8DXL_SPI3_SCK_ADMA_SPI3_SCK 0x6000040 > + IMX8DXL_SPI3_SDO_ADMA_SPI3_SDO 0x6000040 > + IMX8DXL_SPI3_SDI_ADMA_SPI3_SDI 0x6000040 > + IMX8DXL_SPI3_CS1_ADMA_SPI3_CS1 0x6000040 > + >; > + }; > + > + pinctrl_i2c2: i2c2grp { > + fsl,pins = < > + IMX8DXL_SPI1_SCK_ADMA_I2C2_SDA 0x06000021 > + IMX8DXL_SPI1_SDO_ADMA_I2C2_SCL 0x06000021 > + >; > + }; > + > + pinctrl_cm40_lpuart: cm40lpuartgrp { > + fsl,pins = < > + IMX8DXL_ADC_IN2_M40_UART0_RX 0x06000020 > + IMX8DXL_ADC_IN3_M40_UART0_TX 0x06000020 > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + IMX8DXL_SPI1_CS0_ADMA_I2C3_SDA 0x06000021 > + IMX8DXL_SPI1_SDI_ADMA_I2C3_SCL 0x06000021 > + >; > + }; > + > + pinctrl_lpuart0: lpuart0grp { > + fsl,pins = < > + IMX8DXL_UART0_RX_ADMA_UART0_RX 0x06000020 > + IMX8DXL_UART0_TX_ADMA_UART0_TX 0x06000020 > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + IMX8DXL_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 > + IMX8DXL_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 > + IMX8DXL_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 > + IMX8DXL_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 > + IMX8DXL_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 > + IMX8DXL_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 > + IMX8DXL_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021 > + IMX8DXL_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021 > + IMX8DXL_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021 > + IMX8DXL_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021 > + IMX8DXL_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041 > + >; > + }; > + > + pinctrl_usdhc2_gpio: usdhc2gpiogrp { > + fsl,pins = < > + IMX8DXL_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30 0x00000040 /* RESET_B */ > + IMX8DXL_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00 0x00000021 /* WP */ > + IMX8DXL_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01 0x00000021 /* CD */ > + >; > + }; > + > + pinctrl_usdhc2: usdhc2grp { > + fsl,pins = < > + IMX8DXL_ENET0_RGMII_RXC_CONN_USDHC1_CLK 0x06000041 > + IMX8DXL_ENET0_RGMII_RX_CTL_CONN_USDHC1_CMD 0x00000021 > + IMX8DXL_ENET0_RGMII_RXD0_CONN_USDHC1_DATA0 0x00000021 > + IMX8DXL_ENET0_RGMII_RXD1_CONN_USDHC1_DATA1 0x00000021 > + IMX8DXL_ENET0_RGMII_RXD2_CONN_USDHC1_DATA2 0x00000021 > + IMX8DXL_ENET0_RGMII_RXD3_CONN_USDHC1_DATA3 0x00000021 > + IMX8DXL_ENET0_RGMII_TXD0_CONN_USDHC1_VSELECT 0x00000021 > + >; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > new file mode 100644 > index 0000000000000..e26bbbf7f1508 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi > @@ -0,0 +1,72 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > + > +&audio_ipg_clk { > + clock-frequency = <160000000>; > +}; > + > +&dma_ipg_clk { > + clock-frequency = <160000000>; > +}; > + > +&i2c0 { > + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > + interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&i2c1 { > + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > + interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&i2c2 { > + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; > + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&i2c3 { > + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; i2c0/1 and i2c2/3 have different compatible? > + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lpspi0 { > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > + interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lpspi1 { > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > + interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lpspi2 { > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > + interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lpspi3 { > + compatible = "fsl,imx8qxp-spi", "fsl,imx7ulp-spi"; > + interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lpuart0 { > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lpuart1 { > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lpuart2 { > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lpuart3 { > + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; > + interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > new file mode 100644 > index 0000000000000..98f666cbe63bf > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi > @@ -0,0 +1,145 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > + > +/delete-node/ &enet1_lpcg; > +/delete-node/ &fec2; > + > +&conn_subsys { > + conn_enet0_root_clk: clock-conn-enet0-root { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <250000000>; > + clock-output-names = "conn_enet0_root_clk"; > + }; > + > + eqos: ethernet@5b050000 { > + compatible = "nxp,imx8dxl-dwmac-eqos", "snps,dwmac-5.10a"; > + reg = <0x5b050000 0x10000>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "eth_wake_irq", "macirq"; > + clocks = <&eqos_lpcg IMX_LPCG_CLK_4>, > + <&eqos_lpcg IMX_LPCG_CLK_6>, > + <&eqos_lpcg IMX_LPCG_CLK_0>, > + <&eqos_lpcg IMX_LPCG_CLK_5>, > + <&eqos_lpcg IMX_LPCG_CLK_2>; > + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "mem"; > + assigned-clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>; > + assigned-clock-rates = <125000000>; > + power-domains = <&pd IMX_SC_R_ENET_1>; > + clk_csr = <0>; Where is this property documented as bindings? > + status = "disabled"; > + }; > + > + usbotg2: usb@5b0e0000 { > + compatible = "fsl,imx8dxl-usb", "fsl,imx7ulp-usb"; > + reg = <0x5b0e0000 0x200>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; > + fsl,usbphy = <&usbphy2>; > + fsl,usbmisc = <&usbmisc2 0>; > + /* > + * usbotg1 and usbotg2 share one clcok. > + * scu firmware disables the access to the clock and keeps > + * it always on in case other core (M4) uses one of these. > + */ > + clocks = <&clk_dummy>; > + ahb-burst-config = <0x0>; > + tx-burst-size-dword = <0x10>; > + rx-burst-size-dword = <0x10>; > + #stream-id-cells = <1>; > + power-domains = <&pd IMX_SC_R_USB_1>; > + status = "disabled"; > + > + clk_dummy: clock-dummy { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <0>; > + clock-output-names = "clk_dummy"; > + }; > + }; > + > + usbmisc2: usbmisc@5b0e0200 { > + #index-cells = <1>; > + compatible = "fsl,imx7ulp-usbmisc"; > + reg = <0x5b0e0200 0x200>; > + }; > + > + usbphy2: usbphy@0x5b110000 { > + compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy"; > + reg = <0x5b110000 0x1000>; > + clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>; > + power-domains = <&pd IMX_SC_R_USB_1_PHY>; > + status = "disabled"; > + }; > + > + eqos_lpcg: clock-controller@5b240000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5b240000 0x10000>; > + #clock-cells = <1>; > + Unnecessary newline. > + clocks = <&conn_enet0_root_clk>, > + <&conn_axi_clk>, > + <&conn_axi_clk>, > + <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>, > + <&conn_ipg_clk>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>, > + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, > + <IMX_LPCG_CLK_6>; > + clock-output-names = "eqos_ptp", > + "eqos_mem_clk", > + "eqos_aclk", > + "eqos_clk", > + "eqos_csr_clk"; > + power-domains = <&pd IMX_SC_R_ENET_1>; > + }; > + > + usb2_2_lpcg: clock-controller@5b280000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5b280000 0x10000>; > + #clock-cells = <1>; > + > + clock-indices = <IMX_LPCG_CLK_7>; > + clocks = <&conn_ipg_clk>; > + clock-output-names = "usboh3_2_phy_ipg_clk"; > + power-domains = <&pd IMX_SC_R_USB_1_PHY>; > + }; > + Ditto Shawn > +}; > + > +&enet0_lpcg { > + clocks = <&conn_enet0_root_clk>, > + <&conn_enet0_root_clk>, > + <&conn_axi_clk>, > + <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>, > + <&conn_ipg_clk>, > + <&conn_ipg_clk>; > +}; > + > +&fec1 { > + compatible = "fsl,imx8qm-fec"; > + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; > + assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>; > + assigned-clock-rates = <125000000>; > +}; > + > +&usdhc1 { > + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; > + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&usdhc2 { > + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; > + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&usdhc3 { > + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > new file mode 100644 > index 0000000000000..550f513708d85 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi > @@ -0,0 +1,9 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2020 NXP > + */ > + > +&ddr_pmu0 { > + compatible = "fsl,imx8-ddr-pmu"; > + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > new file mode 100644 > index 0000000000000..4aaedb6ce591a > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi > @@ -0,0 +1,78 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > +&flexspi0 { > + compatible = "nxp,imx8dxl-fspi"; > + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_gpio0 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_gpio1 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_gpio2 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_gpio3 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_gpio4 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_gpio5 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_gpio6 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_gpio7 { > + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; > + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_mu0 { > + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_mu1 { > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_mu2 { > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_mu3 { > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_mu4 { > + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; > +}; > + > +&lsio_mu5 { > + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; > + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > new file mode 100644 > index 0000000000000..037591fb01a55 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > @@ -0,0 +1,238 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019~2020, 2022 NXP > + */ > + > +#include <dt-bindings/clock/imx8-clock.h> > +#include <dt-bindings/firmware/imx/rsrc.h> > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/pinctrl/pads-imx8dxl.h> > +#include <dt-bindings/thermal/thermal.h> > + > +/ { > + interrupt-parent = <&gic>; > + #address-cells = <2>; > + #size-cells = <2>; > + > + aliases { > + ethernet0 = &fec1; > + ethernet1 = &eqos; > + gpio0 = &lsio_gpio0; > + gpio1 = &lsio_gpio1; > + gpio2 = &lsio_gpio2; > + gpio3 = &lsio_gpio3; > + gpio4 = &lsio_gpio4; > + gpio5 = &lsio_gpio5; > + gpio6 = &lsio_gpio6; > + gpio7 = &lsio_gpio7; > + mu1 = &lsio_mu1; > + }; > + > + cpus: cpus { > + #address-cells = <2>; > + #size-cells = <0>; > + > + /* We have 1 clusters with 2 Cortex-A35 cores */ > + A35_0: cpu@0 { > + device_type = "cpu"; > + compatible = "arm,cortex-a35"; > + reg = <0x0 0x0>; > + enable-method = "psci"; > + next-level-cache = <&A35_L2>; > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > + #cooling-cells = <2>; > + operating-points-v2 = <&a35_opp_table>; > + }; > + > + A35_1: cpu@1 { > + device_type = "cpu"; > + compatible = "arm,cortex-a35"; > + reg = <0x0 0x1>; > + enable-method = "psci"; > + next-level-cache = <&A35_L2>; > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > + #cooling-cells = <2>; > + operating-points-v2 = <&a35_opp_table>; > + }; > + > + A35_L2: l2-cache0 { > + compatible = "cache"; > + }; > + }; > + > + a35_opp_table: opp-table { > + compatible = "operating-points-v2"; > + opp-shared; > + > + opp-900000000 { > + opp-hz = /bits/ 64 <900000000>; > + opp-microvolt = <1000000>; > + clock-latency-ns = <150000>; > + }; > + > + opp-1200000000 { > + opp-hz = /bits/ 64 <1200000000>; > + opp-microvolt = <1100000>; > + clock-latency-ns = <150000>; > + opp-suspend; > + }; > + }; > + > + gic: interrupt-controller@51a00000 { > + compatible = "arm,gic-v3"; > + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */ > + <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */ > + #interrupt-cells = <3>; > + interrupt-controller; > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + dsp_reserved: dsp@92400000 { > + reg = <0 0x92400000 0 0x2000000>; > + no-map; > + }; > + }; > + > + pmu { > + compatible = "arm,armv8-pmuv3"; > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + system-controller { > + compatible = "fsl,imx-scu"; > + mbox-names = "tx0", > + "rx0", > + "gip3"; > + mboxes = <&lsio_mu1 0 0 > + &lsio_mu1 1 0 > + &lsio_mu1 3 3>; > + > + pd: power-controller { > + compatible = "fsl,scu-pd"; > + #power-domain-cells = <1>; > + wakeup-irq = <160 163 235 236 237 228 229 230 231 238 > + 239 240 166 169>; > + }; > + > + clk: clock-controller { > + compatible = "fsl,imx8dxl-clk", "fsl,scu-clk"; > + #clock-cells = <2>; > + clocks = <&xtal32k &xtal24m>; > + clock-names = "xtal_32KHz", "xtal_24Mhz"; > + }; > + > + iomuxc: pinctrl { > + compatible = "fsl,imx8dxl-iomuxc"; > + }; > + > + ocotp: ocotp { > + compatible = "fsl,imx8qxp-scu-ocotp"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + fec_mac0: mac@2c4 { > + reg = <0x2c4 6>; > + }; > + > + fec_mac1: mac@2c6 { > + reg = <0x2c6 6>; > + }; > + }; > + > + rtc: rtc { > + compatible = "fsl,imx8qxp-sc-rtc"; > + }; > + > + sc_pwrkey: keys { > + compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key"; > + linux,keycode = <KEY_POWER>; > + wakeup-source; > + }; > + > + watchdog { > + compatible = "fsl,imx-sc-wdt"; > + timeout-sec = <60>; > + }; > + > + tsens: thermal-sensor { > + compatible = "fsl,imx-sc-thermal"; > + #thermal-sensor-cells = <1>; > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */ > + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */ > + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ > + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */ > + }; > + > + thermal_zones: thermal-zones { > + cpu-thermal0 { > + polling-delay-passive = <250>; > + polling-delay = <2000>; > + thermal-sensors = <&tsens IMX_SC_R_SYSTEM>; > + > + trips { > + cpu_alert0: trip0 { > + temperature = <107000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + cpu_crit0: trip1 { > + temperature = <127000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&cpu_alert0>; > + cooling-device = > + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + }; > + }; > + }; > + > + /* The two values below cannot be changed by the board */ > + xtal32k: clock-xtal32k { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <32768>; > + clock-output-names = "xtal_32KHz"; > + }; > + > + xtal24m: clock-xtal24m { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <24000000>; > + clock-output-names = "xtal_24MHz"; > + }; > + > + /* sorted in register address */ > + #include "imx8-ss-adma.dtsi" > + #include "imx8-ss-conn.dtsi" > + #include "imx8-ss-ddr.dtsi" > + #include "imx8-ss-lsio.dtsi" > +}; > + > +#include "imx8dxl-ss-adma.dtsi" > +#include "imx8dxl-ss-conn.dtsi" > +#include "imx8dxl-ss-lsio.dtsi" > +#include "imx8dxl-ss-ddr.dtsi" > -- > 2.25.1 > ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2022-08-21 13:15 UTC | newest] Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2022-08-01 20:01 [PATCH v5 0/3] add imx8dxl evk support Shenwei Wang 2022-08-01 20:01 ` [PATCH v5 1/3] dt-bindings: firmware: add missing resource IDs for imx8dxl Shenwei Wang 2022-08-01 20:01 ` [PATCH v5 2/3] dt-bindings: arm: imx: update fsl.yaml " Shenwei Wang 2022-08-01 20:01 ` [PATCH v5 3/3] arm64: dts: imx: add imx8dxl support Shenwei Wang 2022-08-05 16:22 ` Shenwei Wang 2022-08-08 5:47 ` Krzysztof Kozlowski 2022-08-08 18:16 ` [EXT] " Shenwei Wang 2022-08-09 4:16 ` Krzysztof Kozlowski 2022-08-09 16:41 ` Shenwei Wang 2022-08-09 16:41 ` Shenwei Wang 2022-08-18 12:08 ` Shenwei Wang 2022-08-21 13:14 ` Shawn Guo
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.