[PATCH 1/4 v2] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC

[PATCH 1/4 v2] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC

[Shengzhou Liu]

The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
  - Three PCI Express 2.0 controllers
- Additional peripheral interfaces
  - One SATA 2.0 controller
  - Two USB 2.0 controllers with integrated PHY
  - Enhanced secure digital host controller (SD/eSDHC/eMMC)
  - Enhanced serial peripheral interface (eSPI)
  - Four I2C controllers
  - Four 2-pin UARTs or two 4-pin UARTs
  - Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v2: Integrated scott's comments.

 arch/powerpc/boot/dts/fsl/t1023si-post.dtsi | 343 ++++++++++++++++++++++++++++
 arch/powerpc/boot/dts/fsl/t1024si-post.dtsi | 103 +++++++++
 arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi  |  87 +++++++
 3 files changed, 533 insertions(+)
 create mode 100644 arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
 create mode 100644 arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
 create mode 100644 arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi

diff --git a/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
new file mode 100644
index 0000000..cbb3500
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
@@ -0,0 +1,343 @@
+/*
+ * T1023 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,ifc", "simple-bus";
+	interrupts = <25 2 0 0>;
+};
+
+&pci0 {
+	compatible = "fsl,t1023-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	interrupts = <20 2 0 0>;
+	fsl,iommu-parent = <&pamu0>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <20 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 40 1 0 0
+			0000 0 0 2 &mpic 1 1 0 0
+			0000 0 0 3 &mpic 2 1 0 0
+			0000 0 0 4 &mpic 3 1 0 0
+			>;
+	};
+};
+
+&pci1 {
+	compatible = "fsl,t1023-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 0xff>;
+	interrupts = <21 2 0 0>;
+	fsl,iommu-parent = <&pamu0>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <21 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 41 1 0 0
+			0000 0 0 2 &mpic 5 1 0 0
+			0000 0 0 3 &mpic 6 1 0 0
+			0000 0 0 4 &mpic 7 1 0 0
+			>;
+	};
+};
+
+&pci2 {
+	compatible = "fsl,t1023-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	interrupts = <22 2 0 0>;
+	fsl,iommu-parent = <&pamu0>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <22 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 42 1 0 0
+			0000 0 0 2 &mpic 9 1 0 0
+			0000 0 0 3 &mpic 10 1 0 0
+			0000 0 0 4 &mpic 11 1 0 0
+			>;
+	};
+};
+
+&dcsr {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "fsl,dcsr", "simple-bus";
+
+	dcsr-epu@0 {
+		compatible = "fsl,t1023-dcsr-epu", "fsl,dcsr-epu";
+		interrupts = <52 2 0 0
+			      84 2 0 0
+			      85 2 0 0>;
+		reg = <0x0 0x1000>;
+	};
+	dcsr-npc {
+		compatible = "fsl,t1023-dcsr-cnpc", "fsl,dcsr-cnpc";
+		reg = <0x1000 0x1000 0x1002000 0x10000>;
+	};
+	dcsr-nxc@2000 {
+		compatible = "fsl,dcsr-nxc";
+		reg = <0x2000 0x1000>;
+	};
+	dcsr-corenet {
+		compatible = "fsl,dcsr-corenet";
+		reg = <0x8000 0x1000 0x1A000 0x1000>;
+	};
+	dcsr-ocn@11000 {
+		compatible = "fsl,t1023-dcsr-ocn", "fsl,dcsr-ocn";
+		reg = <0x11000 0x1000>;
+	};
+	dcsr-ddr@12000 {
+		compatible = "fsl,dcsr-ddr";
+		dev-handle = <&ddr1>;
+		reg = <0x12000 0x1000>;
+	};
+	dcsr-nal@18000 {
+		compatible = "fsl,t1023-dcsr-nal", "fsl,dcsr-nal";
+		reg = <0x18000 0x1000>;
+	};
+	dcsr-rcpm@22000 {
+		compatible = "fsl,t1023-dcsr-rcpm", "fsl,dcsr-rcpm";
+		reg = <0x22000 0x1000>;
+	};
+	dcsr-snpc@30000 {
+		compatible = "fsl,t1023-dcsr-snpc", "fsl,dcsr-snpc";
+		reg = <0x30000 0x1000 0x1022000 0x10000>;
+	};
+	dcsr-snpc@31000 {
+		compatible = "fsl,t1023-dcsr-snpc", "fsl,dcsr-snpc";
+		reg = <0x31000 0x1000 0x1042000 0x10000>;
+	};
+	dcsr-cpu-sb-proxy@100000 {
+		compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu0>;
+		reg = <0x100000 0x1000 0x101000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@108000 {
+		compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu1>;
+		reg = <0x108000 0x1000 0x109000 0x1000>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "simple-bus";
+
+	soc-sram-error {
+		compatible = "fsl,soc-sram-error";
+		interrupts = <16 2 1 29>;
+	};
+
+	corenet-law@0 {
+		compatible = "fsl,corenet-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <16>;
+	};
+
+	ddr1: memory-controller@8000 {
+		compatible = "fsl,qoriq-memory-controller-v5.0",
+				"fsl,qoriq-memory-controller";
+		reg = <0x8000 0x1000>;
+		interrupts = <16 2 1 23>;
+	};
+
+	cpc: l3-cache-controller@10000 {
+		compatible = "fsl,t1023-l3-cache-controller", "cache";
+		reg = <0x10000 0x1000>;
+		interrupts = <16 2 1 27>;
+	};
+
+	corenet-cf@18000 {
+		compatible = "fsl,corenet2-cf";
+		reg = <0x18000 0x1000>;
+		interrupts = <16 2 1 31>;
+	};
+
+	iommu@20000 {
+		compatible = "fsl,pamu-v1.0", "fsl,pamu";
+		reg = <0x20000 0x1000>;
+		ranges = <0 0x20000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupts = <
+			24 2 0 0
+			16 2 1 30>;
+		pamu0: pamu@0 {
+			reg = <0 0x1000>;
+			fsl,primary-cache-geometry = <128 1>;
+			fsl,secondary-cache-geometry = <32 2>;
+		};
+	};
+
+/include/ "qoriq-mpic.dtsi"
+
+	guts: global-utilities@e0000 {
+		compatible = "fsl,t1023-device-config", "fsl,qoriq-device-config-2.0";
+		reg = <0xe0000 0xe00>;
+		fsl,has-rstcr;
+		fsl,liodn-bits = <12>;
+	};
+
+	clockgen: global-utilities@e1000 {
+		compatible = "fsl,t1023-clockgen", "fsl,qoriq-clockgen-2.0",
+				   "fixed-clock";
+		reg = <0xe1000 0x1000>;
+		clock-output-names = "sysclk";
+		#clock-cells = <0>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		pll0: pll0@800 {
+			#clock-cells = <1>;
+			reg = <0x800 4>;
+			compatible = "fsl,core-pll-clock";
+			clocks = <&clockgen>;
+			clock-output-names = "pll0", "pll0-div2";
+		};
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 4>;
+			compatible = "fsl,core-mux-clock";
+			clocks = <&pll0 0>, <&pll0 1>;
+			clock-names = "pll0_0", "pll0_1";
+			clock-output-names = "cmux0";
+		};
+		mux1: mux1@20 {
+			#clock-cells = <0>;
+			reg = <0x20 4>;
+			compatible = "fsl,core-mux-clock";
+			clocks = <&pll0 0>, <&pll0 1>;
+			clock-names = "pll0_0", "pll0_1";
+			clock-output-names = "cmux1";
+		};
+	};
+
+	rcpm: global-utilities@e2000 {
+		compatible = "fsl,t1023-rcpm", "fsl,qoriq-rcpm-2.0";
+		reg = <0xe2000 0x1000>;
+	};
+
+	sfp: sfp@e8000 {
+		compatible = "fsl,t1023-sfp";
+		reg = <0xe8000 0x1000>;
+	};
+
+	serdes: serdes@ea000 {
+		compatible = "fsl,t1023-serdes";
+		reg = <0xea000 0x4000>;
+	};
+
+	scfg: global-utilities@fc000 {
+		compatible = "fsl,t1023-scfg";
+		reg = <0xfc000 0x1000>;
+	};
+
+/include/ "elo3-dma-0.dtsi"
+/include/ "elo3-dma-1.dtsi"
+
+/include/ "qoriq-espi-0.dtsi"
+	spi@110000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "qoriq-esdhc-0.dtsi"
+	sdhc@114000 {
+		compatible = "fsl,t1023-esdhc", "fsl,esdhc";
+		fsl,iommu-parent = <&pamu0>;
+		fsl,liodn-reg = <&guts 0x530>; /* eSDHCLIODNR */
+		sdhci,auto-cmd12;
+		no-1-8-v;
+	};
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-gpio-1.dtsi"
+/include/ "qoriq-gpio-2.dtsi"
+/include/ "qoriq-gpio-3.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+		usb0: usb@210000 {
+			compatible = "fsl-usb2-mph-v2.5", "fsl-usb2-mph";
+			fsl,iommu-parent = <&pamu0>;
+			fsl,liodn-reg = <&guts 0x520>; /* USB1LIODNR */
+			phy_type = "utmi";
+			port0;
+		};
+/include/ "qoriq-usb2-dr-0.dtsi"
+		usb1: usb@211000 {
+			compatible = "fsl-usb2-dr-v2.5", "fsl-usb2-dr";
+			fsl,iommu-parent = <&pamu0>;
+			fsl,liodn-reg = <&guts 0x524>; /* USB2LIODNR */
+			dr_mode = "host";
+			phy_type = "utmi";
+		};
+/include/ "qoriq-sata2-0.dtsi"
+sata@220000 {
+			fsl,iommu-parent = <&pamu0>;
+			fsl,liodn-reg = <&guts 0x550>; /* SATA1LIODNR */
+};
+
+/include/ "qoriq-sec5.0-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
new file mode 100644
index 0000000..33c3313
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
@@ -0,0 +1,103 @@
+/*
+ * T1024 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "t1023si-post.dtsi"
+
+/ {
+	aliases {
+		vga = &display;
+		display = &display;
+	};
+
+	qe:qe@ffe140000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "qe";
+		compatible = "fsl,qe";
+		ranges = <0x0 0xf 0xfe140000 0x40000>;
+		reg = <0xf 0xfe140000 0 0x480>;
+		fsl,qe-num-riscs = <1>;
+		fsl,qe-num-snums = <28>;
+		brg-frequency = <0>;
+		bus-frequency = <0>;
+	};
+};
+
+&soc {
+/include/ "qoriq-tdm1.0.dtsi"
+
+	display:display@180000 {
+		compatible = "fsl,t1024-diu", "fsl,diu";
+		reg = <0x180000 1000>;
+		interrupts = <74 2 0 0>;
+	};
+};
+
+&qe {
+	qeic: interrupt-controller@80 {
+		interrupt-controller;
+		compatible = "fsl,qe-ic";
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x80 0x80>;
+		interrupts = <95 2 0 0  94 2 0 0>; //high:79 low:78
+	};
+
+	ucc@2000 {
+		cell-index = <1>;
+		reg = <0x2000 0x200>;
+		interrupts = <32>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@2200 {
+		cell-index = <3>;
+		reg = <0x2200 0x200>;
+		interrupts = <34>;
+		interrupt-parent = <&qeic>;
+	};
+
+	muram@10000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,qe-muram", "fsl,cpm-muram";
+		ranges = <0x0 0x10000 0x6000>;
+
+		data-only@0 {
+			compatible = "fsl,qe-muram-data",
+			"fsl,cpm-muram-data";
+			reg = <0x0 0x6000>;
+		};
+	};
+};
diff --git a/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi b/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
new file mode 100644
index 0000000..1f1a9f8
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
@@ -0,0 +1,87 @@
+/*
+ * T1024/T1023 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e5500_power_isa.dtsi"
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		ccsr = &soc;
+		dcsr = &dcsr;
+
+		dma0 = &dma0;
+		dma1 = &dma1;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		sdhc = &sdhc;
+
+		crypto = &crypto;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: PowerPC,e5500@0 {
+			device_type = "cpu";
+			reg = <0>;
+			clocks = <&mux0>;
+			next-level-cache = <&L2_1>;
+			L2_1: l2-cache {
+				next-level-cache = <&cpc>;
+			};
+		};
+		cpu1: PowerPC,e5500@1 {
+			device_type = "cpu";
+			reg = <1>;
+			clocks = <&mux1>;
+			next-level-cache = <&L2_2>;
+			L2_2: l2-cache {
+				next-level-cache = <&cpc>;
+			};
+		};
+	};
+};
-- 
2.1.0.27.g96db324

[PATCH 2/4 v2] powerpc/fsl-booke: Add T1024 QDS board support

[Shengzhou Liu]

Add support for Freescale T1024/T1023 QorIQ Development System Board.

T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.

T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- Ethernet interfaces:
  - Two 10M/100M/1G RGMII ports on-board
  - Three 1G/2.5Gbps SGMII ports
  - Four 1Gbps QSGMII ports
  - one 10Gbps XFI or 10G Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
  - Chrontel CH7201 for HDMI connection.
  - TI DS90C387R for direct LCD connection.
  - Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
  - 32-bit RISC controller for flexible support of the communications peripherals
  - Serial DMA channel for receive and transmit on all serial channels
  - Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep sleep power management implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A and one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v2: no change

 arch/powerpc/boot/dts/t1024qds.dts            | 251 ++++++++++++++++++++++++++
 arch/powerpc/platforms/85xx/Kconfig           |   2 +-
 arch/powerpc/platforms/85xx/corenet_generic.c |   1 +
 3 files changed, 253 insertions(+), 1 deletion(-)
 create mode 100644 arch/powerpc/boot/dts/t1024qds.dts

diff --git a/arch/powerpc/boot/dts/t1024qds.dts b/arch/powerpc/boot/dts/t1024qds.dts
new file mode 100644
index 0000000..14122cf
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1024qds.dts
@@ -0,0 +1,251 @@
+/*
+ * T1024 QDS Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+
+/ {
+	model = "fsl,T1024QDS";
+	compatible = "fsl,T1024QDS";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	ifc: localbus@ffe124000 {
+		reg = <0xf 0xfe124000 0 0x2000>;
+		ranges = <0 0 0xf 0xe8000000 0x08000000
+			  2 0 0xf 0xff800000 0x00010000
+			  3 0 0xf 0xffdf0000 0x00008000>;
+
+		nor@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x8000000>;
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		nand@2,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x2 0x0 0x10000>;
+		};
+
+		board-control@3,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,tetra-fpga", "fsl,fpga-qixis";
+			reg = <3 0 0x300>;
+			ranges = <0 3 0 0x300>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	dcsr: dcsr@f00000000 {
+		ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+	};
+
+	soc: soc@ffe000000 {
+		ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+		reg = <0xf 0xfe000000 0 0x00001000>;
+		spi@110000 {
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "micron,n25q128a11";  /* 16MB */
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+			};
+
+			flash@1 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "sst,sst25wf040";  /* 512KB */
+				reg = <1>;
+				spi-max-frequency = <10000000>;
+			};
+
+			flash@2 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "eon,en25s64";   /* 8MB */
+				reg = <2>;
+				spi-max-frequency = <10000000>;
+			};
+
+			slic@2 {
+				compatible = "maxim,ds26522";
+				reg = <2>;
+				spi-max-frequency = <2000000>;
+			};
+
+			slic@3 {
+				compatible = "maxim,ds26522";
+				reg = <3>;
+				spi-max-frequency = <2000000>;
+			};
+		};
+
+		i2c@118000 {
+			pca9547@77 {
+				compatible = "nxp,pca9547";
+				reg = <0x77>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+
+					eeprom@50 {
+						compatible = "at24,24c512";
+						reg = <0x50>;
+					};
+
+					eeprom@51 {
+						compatible = "at24,24c02";
+						reg = <0x51>;
+					};
+
+					eeprom@57 {
+						compatible = "at24,24c02";
+						reg = <0x57>;
+					};
+				};
+
+				i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+
+					ina220@40 {
+						compatible = "ti,ina220";
+						reg = <0x40>;
+						shunt-resistor = <1000>;
+					};
+
+					ina220@41 {
+						compatible = "ti,ina220";
+						reg = <0x41>;
+						shunt-resistor = <1000>;
+					};
+				};
+
+				i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x3>;
+
+					adt7461@4c {
+						/* Thermal Monitor */
+						compatible = "adi,adt7461";
+						reg = <0x4c>;
+					};
+
+					eeprom@55 {
+						compatible = "at24,24c02";
+						reg = <0x55>;
+					};
+
+					eeprom@56 {
+						compatible = "at24,24c512";
+						reg = <0x56>;
+					};
+
+					eeprom@57 {
+						compatible = "at24,24c512";
+						reg = <0x57>;
+					};
+				};
+			};
+			rtc@68 {
+				compatible = "dallas,ds3232";
+				reg = <0x68>;
+				interrupts = <0x5 0x1 0 0>;
+			};
+		};
+	};
+
+	pci0: pcie@ffe240000 {
+		reg = <0xf 0xfe240000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci1: pcie@ffe250000 {
+		reg = <0xf 0xfe250000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci2: pcie@ffe260000 {
+		reg = <0xf 0xfe260000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+};
+
+/include/ "fsl/t1024si-post.dtsi"
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 2fb4b24..e628d40 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -282,7 +282,7 @@ config CORENET_GENERIC
 	  For 64bit kernel, the following boards are supported:
 	    T208x QDS/RDB, T4240 QDS/RDB and B4 QDS
 	  The following boards are supported for both 32bit and 64bit kernel:
-	    P5020 DS, P5040 DS and T104xQDS/RDB
+	    P5020 DS, P5040 DS, T102x QDS, T104x QDS/RDB
 
 endif # FSL_SOC_BOOKE
 
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index 9824d2c..f61f477 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -150,6 +150,7 @@ static const char * const boards[] __initconst = {
 	"fsl,B4860QDS",
 	"fsl,B4420QDS",
 	"fsl,B4220QDS",
+	"fsl,T1024QDS",
 	"fsl,T1040QDS",
 	"fsl,T1042QDS",
 	"fsl,T1040RDB",
-- 
2.1.0.27.g96db324

[PATCH 3/4 v2] powerpc/fsl-booke: Add T1024 RDB board support

[Shengzhou Liu]

T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.

T1024RDB board Overview
-----------------------
- Processor: T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- Memory: 64-bit 4GB DDR3L UDIMM with ECC and interleaving support
- Ethernet: two 1G RGMII ports, one 2.5G SGMII port and one 10G Base-T port
- Accelerator: DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 1GB NAND Flash and CPLD system controlling
- PCIe: one PCIe slot and two Mini-PCIe connectors on-board
- USB: two Type-A USB2.0 ports with internal PHY
- eSDHC: one SDHC/MMC/eMMC connector
- eSPI: one 64MB N25Q512 SPI flash
- QE-TDM: support TDM Riser card
   - 32-bit RISC controller for flexible support of the communications peripherals
   - Serial DMA channel for receive and transmit on all serial channels
   - Two universal communication controllers, supporting TDM, HDLC, and UART
- I2C: four I2C controllers
- UART: two UART on board
- Deep sleep power management support

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v2: Integrated scott's comments.

 arch/powerpc/boot/dts/t1024rdb.dts            | 185 ++++++++++++++++++++++++++
 arch/powerpc/platforms/85xx/Kconfig           |   2 +-
 arch/powerpc/platforms/85xx/corenet_generic.c |   1 +
 3 files changed, 187 insertions(+), 1 deletion(-)
 create mode 100644 arch/powerpc/boot/dts/t1024rdb.dts

diff --git a/arch/powerpc/boot/dts/t1024rdb.dts b/arch/powerpc/boot/dts/t1024rdb.dts
new file mode 100644
index 0000000..eb1d51b
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1024rdb.dts
@@ -0,0 +1,185 @@
+/*
+ * T1024 RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+
+/ {
+	model = "fsl,T1024RDB";
+	compatible = "fsl,T1024RDB";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	ifc: localbus@ffe124000 {
+		reg = <0xf 0xfe124000 0 0x2000>;
+		ranges = <0 0 0xf 0xe8000000 0x08000000
+			  2 0 0xf 0xff800000 0x00010000
+			  3 0 0xf 0xffdf0000 0x00008000>;
+
+		nor@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x8000000>;
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		nand@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x2 0x0 0x10000>;
+		};
+
+		board-control@2,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,t1024-cpld";
+			reg = <3 0 0x300>;
+			ranges = <0 3 0 0x300>;
+			bank-width = <1>;
+			device-width = <1>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	dcsr: dcsr@f00000000 {
+		ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+	};
+
+	soc: soc@ffe000000 {
+		ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+		reg = <0xf 0xfe000000 0 0x00001000>;
+		spi@110000 {
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "micron,n25q512ax3";
+				reg = <0>;
+				spi-max-frequency = <10000000>; /* input clk */
+			};
+
+			slic@1 {
+				compatible = "maxim,ds26522";
+				reg = <1>;
+				spi-max-frequency = <2000000>;
+			};
+
+			slic@2 {
+				compatible = "maxim,ds26522";
+				reg = <2>;
+				spi-max-frequency = <2000000>;
+			};
+		};
+
+		i2c@118000 {
+			adt7461@4c {
+				/* Thermal Monitor */
+				compatible = "adi,adt7461";
+				reg = <0x4c>;
+			};
+
+			eeprom@50 {
+				compatible = "at24,24c256";
+				reg = <0x50>;
+			};
+
+			rtc@68 {
+				compatible = "dallas,ds1339";
+				reg = <0x68>;
+				interrupts = <0x1 0x1 0 0>;
+			};
+		};
+
+		i2c@118100 {
+			pca9546@77 {
+				compatible = "nxp,pca9546";
+				reg = <0x77>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+
+	pci0: pcie@ffe240000 {
+		reg = <0xf 0xfe240000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci1: pcie@ffe250000 {
+		reg = <0xf 0xfe250000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci2: pcie@ffe260000 {
+		reg = <0xf 0xfe260000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+};
+
+/include/ "fsl/t1024si-post.dtsi"
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index e628d40..97915fe 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -282,7 +282,7 @@ config CORENET_GENERIC
 	  For 64bit kernel, the following boards are supported:
 	    T208x QDS/RDB, T4240 QDS/RDB and B4 QDS
 	  The following boards are supported for both 32bit and 64bit kernel:
-	    P5020 DS, P5040 DS, T102x QDS, T104x QDS/RDB
+	    P5020 DS, P5040 DS, T102x QDS/RDB, T104x QDS/RDB
 
 endif # FSL_SOC_BOOKE
 
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index f61f477..d7c1b4d 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -151,6 +151,7 @@ static const char * const boards[] __initconst = {
 	"fsl,B4420QDS",
 	"fsl,B4220QDS",
 	"fsl,T1024QDS",
+	"fsl,T1024RDB",
 	"fsl,T1040QDS",
 	"fsl,T1042QDS",
 	"fsl,T1040RDB",
-- 
2.1.0.27.g96db324

[PATCH 4/4 v2] powerpc/fsl-booke: Add T1023 RDB board support

[Shengzhou Liu]

T1023RDB is a Freescale Reference Design Board that hosts T1023 SoC.

T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - one 1G RGMII port on-board(RTL8211F PHY)
  - one 1G SGMII port on-board(RTL8211F PHY)
  - one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR:  128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC flash on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v2: no change

 arch/powerpc/boot/dts/t1023rdb.dts            | 151 ++++++++++++++++++++++++++
 arch/powerpc/platforms/85xx/corenet_generic.c |   1 +
 2 files changed, 152 insertions(+)
 create mode 100644 arch/powerpc/boot/dts/t1023rdb.dts

diff --git a/arch/powerpc/boot/dts/t1023rdb.dts b/arch/powerpc/boot/dts/t1023rdb.dts
new file mode 100644
index 0000000..3780e68
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1023rdb.dts
@@ -0,0 +1,151 @@
+/*
+ * T1023 RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+
+/ {
+	model = "fsl,T1023RDB";
+	compatible = "fsl,T1023RDB";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	ifc: localbus@ffe124000 {
+		reg = <0xf 0xfe124000 0 0x2000>;
+		ranges = <0 0 0xf 0xe8000000 0x08000000
+			  1 0 0xf 0xff800000 0x00010000>;
+
+		nor@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x8000000>;
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		nand@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x2 0x0 0x10000>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	dcsr: dcsr@f00000000 {
+		ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+	};
+
+	soc: soc@ffe000000 {
+		ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+		reg = <0xf 0xfe000000 0 0x00001000>;
+		spi@110000 {
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "spansion,s25fl512s";
+				reg = <0>;
+				spi-max-frequency = <10000000>; /* input clk */
+			};
+		};
+
+		i2c@118000 {
+			eeprom@50 {
+				compatible = "stm,m24256";
+				reg = <0x50>;
+			};
+
+			rtc@68 {
+				compatible = "dallas,ds1339";
+				reg = <0x68>;
+				interrupts = <0x5 0x1 0 0>;
+			};
+		};
+
+		i2c@118100 {
+		};
+	};
+
+	pci0: pcie@ffe240000 {
+		reg = <0xf 0xfe240000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci1: pcie@ffe250000 {
+		reg = <0xf 0xfe250000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci2: pcie@ffe260000 {
+		reg = <0xf 0xfe260000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+};
+
+/include/ "fsl/t1023si-post.dtsi"
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index d7c1b4d..bd839dc 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -150,6 +150,7 @@ static const char * const boards[] __initconst = {
 	"fsl,B4860QDS",
 	"fsl,B4420QDS",
 	"fsl,B4220QDS",
+	"fsl,T1023RDB",
 	"fsl,T1024QDS",
 	"fsl,T1024RDB",
 	"fsl,T1040QDS",
-- 
2.1.0.27.g96db324

Re: [PATCH 1/4 v2] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC

[Scott Wood]

On Wed, 2015-04-08 at 18:46 +0800, Shengzhou Liu wrote:
> +	clockgen: global-utilities@e1000 {
> +		compatible = "fsl,t1023-clockgen", "fsl,qoriq-clockgen-2.0",
> +				   "fixed-clock";
> +		reg = <0xe1000 0x1000>;
> +		clock-output-names = "sysclk";
> +		#clock-cells = <0>;

Why aren't you using qoriq-clockgen2.dtsi?  Where is ranges?

We've been putting the sysclk in its own node, though even after reading
the discussion in http://patchwork.ozlabs.org/patch/274134/ and
http://patchwork.ozlabs.org/patch/290226/ I still don't know what was
wrong with the unified approach.


> +		data-only@0 {
> +			compatible = "fsl,qe-muram-data",
> +			"fsl,cpm-muram-data";
> +			reg = <0x0 0x6000>;

Whitespace.

-Scott

Re: [PATCH 3/4 v2] powerpc/fsl-booke: Add T1024 RDB board support

[Scott Wood]

On Wed, 2015-04-08 at 18:46 +0800, Shengzhou Liu wrote:
> T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
> 
> T1024RDB board Overview
> -----------------------
> - Processor: T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
> - Memory: 64-bit 4GB DDR3L UDIMM with ECC and interleaving support
> - Ethernet: two 1G RGMII ports, one 2.5G SGMII port and one 10G Base-T port
> - Accelerator: DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
> - SerDes: 4 lanes up to 10.3125GHz
> - IFC: 128MB NOR Flash, 1GB NAND Flash and CPLD system controlling
> - PCIe: one PCIe slot and two Mini-PCIe connectors on-board
> - USB: two Type-A USB2.0 ports with internal PHY
> - eSDHC: one SDHC/MMC/eMMC connector
> - eSPI: one 64MB N25Q512 SPI flash
> - QE-TDM: support TDM Riser card
>    - 32-bit RISC controller for flexible support of the communications peripherals
>    - Serial DMA channel for receive and transmit on all serial channels
>    - Two universal communication controllers, supporting TDM, HDLC, and UART
> - I2C: four I2C controllers
> - UART: two UART on board
> - Deep sleep power management support
> 
> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
> ---
> v2: Integrated scott's comments.

My comment was to add a binding for the QE TDM stuff, not to remove it.

-Scott

Re: [PATCH 1/4 v2] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC

[Scott Wood]

On Wed, 2015-04-08 at 18:46 +0800, Shengzhou Liu wrote:
> The T1024 SoC includes the following function and features:
> - Two 64-bit Power architecture e5500 cores, up to 1.4GHz
> - private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
> - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
> - Data Path Acceleration Architecture (DPAA) incorporating acceleration
> - Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
> - High-speed peripheral interfaces
>   - Three PCI Express 2.0 controllers
> - Additional peripheral interfaces
>   - One SATA 2.0 controller
>   - Two USB 2.0 controllers with integrated PHY
>   - Enhanced secure digital host controller (SD/eSDHC/eMMC)
>   - Enhanced serial peripheral interface (eSPI)
>   - Four I2C controllers
>   - Four 2-pin UARTs or two 4-pin UARTs
>   - Integrated Flash Controller supporting NAND and NOR flash
> - Two 8-channel DMA engines
> - Multicore programmable interrupt controller (PIC)
> - LCD interface (DIU) with 12 bit dual data rate
> - QUICC Engine block supporting TDM, HDLC, and UART
[snip]
> +&soc {
> +/include/ "qoriq-tdm1.0.dtsi"

Where is this file?  Is there some dependency you've forgotten to
mention?

If this is meant to apply after
http://patchwork.ozlabs.org/patch/457605/
is that really QUICC engine TDM as described in the comment above?

-Scott

RE: [PATCH 3/4 v2] powerpc/fsl-booke: Add T1024 RDB board support

[Shengzhou.Liu]

PiA+IC0tLQ0KPiA+IHYyOiBJbnRlZ3JhdGVkIHNjb3R0J3MgY29tbWVudHMuDQo+IA0KPiBNeSBj
b21tZW50IHdhcyB0byBhZGQgYSBiaW5kaW5nIGZvciB0aGUgUUUgVERNIHN0dWZmLCBub3QgdG8g
cmVtb3ZlIGl0Lg0KPiANCj4gLVNjb3R0IA0KDQpRRSBURE0gaGFzIG5vdCBiZWVuIHVwc3RyZWFt
IG9uIGFueSBmc2wtYm9hcmQsIGl0IG5lZWRzIFFFIFRETSBvd25lciBmaW5pc2ggaXQgdW5pZm9y
bWx5IGZvciB0aG9zZSBib2FyZHMocDEwMjEsIHAxMDI1LCB0MTA0MCwgdDEwMjQsIGV0Yykgd2l0
aCBiaW5kaW5nLg0K

RE: [PATCH 1/4 v2] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC

[Shengzhou.Liu]

PiA+ICsmc29jIHsNCj4gPiArL2luY2x1ZGUvICJxb3JpcS10ZG0xLjAuZHRzaSINCj4gDQo+IFdo
ZXJlIGlzIHRoaXMgZmlsZT8gIElzIHRoZXJlIHNvbWUgZGVwZW5kZW5jeSB5b3UndmUgZm9yZ290
dGVuIHRvIG1lbnRpb24/DQo+IA0KPiBJZiB0aGlzIGlzIG1lYW50IHRvIGFwcGx5IGFmdGVyDQo+
IGh0dHA6Ly9wYXRjaHdvcmsub3psYWJzLm9yZy9wYXRjaC80NTc2MDUvDQo+IGlzIHRoYXQgcmVh
bGx5IFFVSUNDIGVuZ2luZSBURE0gYXMgZGVzY3JpYmVkIGluIHRoZSBjb21tZW50IGFib3ZlPw0K
PiANCj4gLVNjb3R0DQpZZXMsIGl0IGRlcGVuZHMgb24gaHR0cDovL3BhdGNod29yay5vemxhYnMu
b3JnL3BhdGNoLzQ1NzYwNS8NCnJpZ2h0IHRoYXQncyByZWFsbHkgUVVJQ0MgZW5naW5lIFRETS4N
Cg0K

Re: [PATCH 1/4 v2] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC

[Scott Wood]

On Thu, 2015-04-09 at 01:29 -0500, Liu Shengzhou-B36685 wrote:
> > > +&soc {
> > > +/include/ "qoriq-tdm1.0.dtsi"
> > 
> > Where is this file?  Is there some dependency you've forgotten to mention?
> > 
> > If this is meant to apply after
> > http://patchwork.ozlabs.org/patch/457605/
> > is that really QUICC engine TDM as described in the comment above?
> > 
> > -Scott
> Yes, it depends on http://patchwork.ozlabs.org/patch/457605/
> right that's really QUICC engine TDM.

That doesn't look like anything related to the QUICC engine, and CCSR
offset 0x185000 is reserved in the t1024 manual.

-Scott