* Cannot boot after the last update...
@ 2014-07-23 8:16 Konstantin Kovalev
2014-07-25 5:21 ` Otavio Salvador
0 siblings, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-07-23 8:16 UTC (permalink / raw)
To: meta-freescale
[-- Attachment #1: Type: text/plain, Size: 1738 bytes --]
Hello,
Some details:
I have Freescale Sabre SD board on iMX6q processor.
***************************************************
Build Configuration:
BB_VERSION = "1.23.1"
BUILD_SYS = "x86_64-linux"
NATIVELSBSTRING = "Fedora-20"
TARGET_SYS = "arm-poky-linux-gnueabi"
MACHINE = "imx6qsabresd"
DISTRO = "poky"
DISTRO_VERSION = "1.6+snapshot-20140723"
TUNE_FEATURES = "arm armv7a vfp neon callconvention-hard cortexa9"
TARGET_FPU = "vfp-neon"
meta
meta-yocto = "(detachedfrom8b7116d):8b7116d25ed6255a03895d835e5a0560858ab496"
meta-oe = "(detachedfrom743751e):743751e20cc266143130fb5bb49efb4c86b9e02b"
meta-fsl-arm = "(detachedfromd900d93):d900d935e1f45a79c7116c4fd290baaa447a870d"
meta-fsl-arm-extra = "(detachedfromc3b74cd):c3b74cd1de4fba69f14ef6366fdc15f11d32e485"
meta-fsl-demos = "(nobranch):e60ea240aecbf8fc69c4d18ab6d1361376372c6e"
***************************************************
I use the master-next branch and fsl-image-multimedia-full.
So my problem is that after "repo sync" on last friday I cannot boot the system from the resulting image from my SD-card.
I have written the image by this command "sudo dd if=fsl-image-multimedia-full-imx6qsabresd.sdcard of=/dev/sdb bs=4M &&sync"
There are two lines in boot log:
*******************************************************************
No filesystem could mount root, tried: ext3 ext2 ext4 vfat fuseblk
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,10)
*******************************************************************
I attached the full log.
Please help!
Thanks in advance!
Best regards,
Konstantin.
[-- Attachment #2: boot_log.txt --]
[-- Type: text/plain, Size: 20525 bytes --]
U-Boot 2014.07 (Jul 22 2014 - 17:06:50)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment
auto-detected panel HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
PMIC: PFUZE100 ID=0x10
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
5290904 bytes read in 257 ms (19.6 MiB/s)
Booting from mmc ...
reading imx6q-sabresd.dtb
47179 bytes read in 21 ms (2.1 MiB/s)
Kernel image @ 0x12000000 [ 0x000000 - 0x50bb98 ]
## Flattened Device Tree blob at 18000000
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800e84a
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 3.10.17-1.0.0_ga+g2a69800 (togran@togran_pc.pdc.vozpp) (gcc version 4.9.0 (GCC) ) #1 SMP PREEMPT Tue Jul 22 14:56:56 MSK 2014
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX6 Quad/DualLite (Device Tree), model: Freescale i.MX6 Quad SABRE Smart Device Board
cma: CMA: reserved 320 MiB at 3c000000
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 8 pages/cpu @8151b000 s8896 r8192 d15680 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk1p2 rootwait rw
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1024MB = 1024MB total
Memory: 697660k/697660k available, 350916k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80c0429c (12273 kB)
.init : 0x80c05000 - 0x80c482c0 ( 269 kB)
.data : 0x80c4a000 - 0x80c9abe0 ( 323 kB)
.bss : 0x80c9abe0 - 0x80d03d64 ( 421 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1048576 B
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
CPU identified as i.MX6Q, silicon rev 1.2
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x806323b0 - 0x80632408
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: Booted secondary processor
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: Booted secondary processor
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Use WDOG2 as reset source
syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
vdd1p1: 800 <--> 1375 mV at 1125 mV
vdd3p0: 2800 <--> 3150 mV at 3000 mV
vdd2p5: 2000 <--> 2750 mV at 2425 mV
cpu: 725 <--> 1450 mV at 1100 mV
vddpu: 725 <--> 1450 mV at 1100 mV
vddsoc: 725 <--> 1450 mV at 1175 mV
syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
bio: create slab <bio-0> at 0
mxs-dma 110000.dma-apbh: initialized
usb_otg_vbus: 5000 mV
usb_h1_vbus: 5000 mV
wm8962-supply: no parameters
mipi_dsi_pwr_on: no parameters
sensor-supply: 3300 mV
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c i2c-0: IMX I2C adapter registered
i2c i2c-1: IMX I2C adapter registered
i2c i2c-2: IMX I2C adapter registered
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
pureg-dummy: no parameters
imx6_busfreq busfreq.15: DDR medium rate not supported.
Bus freq driver module loaded
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 2002
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
imx-weim 21b8000.weim: WEIM driver registered.
mxc_mipi_dsi 21e0000.mipi: i.MX MIPI DSI driver probed
MIPI DSI driver module loaded
mxc_sdc_fb fb.30: register mxc display driver ldb
imx-ipuv3 2800000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 128x48
mxc_sdc_fb fb.31: register mxc display driver hdmi
mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1
fbcvt: 1920x1080@60: CVT Name - 2.073M9
mxc_sdc_fb fb.32: register mxc display driver lcd
mxc_sdc_fb fb.32: ipu0-di0 already in use
mxc_sdc_fb: probe of fb.32 failed with error -16
mxc_sdc_fb fb.33: register mxc display driver ldb
imx-sdma 20ec000.sdma: no iram assigned, using external mem
imx-sdma 20ec000.sdma: loaded firmware 1.1
imx-sdma 20ec000.sdma: initialized
pfuze100-regulator 1-0008: Full lay: 1, Metal lay: 1
pfuze100-regulator 1-0008: FAB: 0, FIN: 0
pfuze100-regulator 1-0008: pfuze100 found.
SW1AB: 300 <--> 1875 mV at 1375 mV
SW1C: 300 <--> 1875 mV at 1375 mV
SW2: 800 <--> 3300 mV at 3300 mV
SW3A: 400 <--> 1975 mV at 1500 mV
SW3B: 400 <--> 1975 mV at 1500 mV
SW4: 800 <--> 3300 mV at 3150 mV
SWBST: 5000 <--> 5150 mV at 5000 mV
VSNVS: 1000 <--> 3000 mV at 3000 mV
VREFDDR: 750 mV
VGEN1: 800 <--> 1550 mV at 1500 mV
VGEN2: 800 <--> 1550 mV at 1500 mV
VGEN3: 1800 <--> 3300 mV at 2800 mV
VGEN4: 1800 <--> 3300 mV at 1800 mV
VGEN5: 1800 <--> 3300 mV at 3000 mV
VGEN6: 1800 <--> 3300 mV at 3300 mV
Serial: IMX driver
2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled
serial: Freescale lpuart driver
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
Wait for CR ACK error!
sata phy RX_PLL is stable!
ahci: SSS flag set, parallel bus scan disabled
ahci ahci: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 71
m25p80 spi32766.0: m25p32 (4096 Kbytes)
spi_imx 2008000.ecspi: probed
CAN device driver interface
libphy: fec_enet_mii_bus: probed
fec 2188000.ethernet eth0: registered PHC device 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
usbcore: registered new interface driver usb-storage
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ci_hdrc ci_hdrc.1: doesn't support gadget
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
elan-touch 2-0010: elan - Read Hello Packet Failed
elan-touch: probe of 2-0010 failed with error -22
egalax_ts 1-0004: Failed to read firmware version
egalax_ts: probe of 1-0004 failed with error -5
input: eGalax Touch Screen as /devices/soc0/soc.1/2100000.aips-bus/21a8000.i2c/i2c-2/2-0004/input/input0
input: max11801_ts as /devices/soc0/soc.1/2100000.aips-bus/21a4000.i2c/i2c-1/1-0048/input/input1
input: isl29023 light sensor as /devices/virtual/input/input2
isl29023 2-0044: driver version 1.0 enabled
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
i2c /dev entries driver
ata1: SATA link down (SStatus 0 SControl 300)
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video16
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video17
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video18
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video19
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video20
usb 1-1: new high-speed USB device number 2 using ci_hdrc
mag3110 2-000e: check mag3110 chip ID
input: mag3110 as /devices/virtual/input/input3
mag3110 2-000e: mag3110 is probed
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
input: mma845x as /devices/virtual/input/input4
imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: no vqmmc regulator found
mmc1: no vmmc regulator found
mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
mmc2: no vqmmc regulator found
mmc2: no vmmc regulator found
mmc1: new high speed SDHC card at address 0007
mmcblk0: mmc1:0007 SD16G 14.9 GiB
mmcblk0: p1 p2
mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
usb 1-1.1: new high-speed USB device number 3 using ci_hdrc
hub 1-1.1:1.0: USB hub found
hub 1-1.1:1.0: 4 ports detected
mmc2: new high speed DDR MMC card at address 0001
mmcblk1: mmc2:0001 SEM08G 7.39 GiB
mmcblk1boot0: mmc2:0001 SEM08G partition 1 2.00 MiB
mmcblk1boot1: mmc2:0001 SEM08G partition 2 2.00 MiB
mmcblk1rpmb: mmc2:0001 SEM08G partition 3 128 KiB
mmcblk1: p1 p2
mmcblk1boot1: unknown partition table
mmcblk1boot0: unknown partition table
Galcore version 4.6.9.9754
mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
mxc_asrc 2034000.asrc: mxc_asrc registered
mxc_vpu 2040000.vpu: VPU initialized
leds-gpio leds.20: pins are not configured from the driver
usb 1-1.1.1: new low-speed USB device number 4 using ci_hdrc
caam 2100000.caam: device ID = 0x0a16010000000000 (Era -524)
caam 2100000.caam: job rings = 2, qi = 0
caam 2100000.caam: authenc-hmac-md5-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des-caam
caam 2100000.caam: ecb-des-caam
caam 2100000.caam: ecb-arc4-caam
caam 2100000.caam: ecb-aes-caam
caam 2100000.caam: ctr-aes-caam
caam 2100000.caam: cbc-aes-caam
caam 2100000.caam: ecb-des3-caam
caam 2100000.caam: cbc-3des-caam
caam 2100000.caam: cbc-des-caam
caam 2100000.caam: fsl,sec-v4.0 algorithms registered in /proc/crypto
platform 2101000.jr0: registering rng-caam
platform caam_sm: caam_sm_test: 8-byte key test match OK
platform caam_sm: caam_sm_test: 16-byte key test match OK
platform caam_sm: caam_sm_test: 32-byte key test match OK
platform caam_secvio.40: security violation service handlers armed
usb 1-1.1.2: new high-speed USB device number 5 using ci_hdrc
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/input/input5
hid-generic 0003:413C:2103.0001: input: USB HID v1.00 Keyboard [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input0
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.1/input/input6
hid-generic 0003:413C:2103.0002: input: USB HID v1.10 Mouse [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
i2c-core: driver [cs42888] using legacy suspend method
i2c-core: driver [cs42888] using legacy resume method
wm8962 0-001a: customer id 0 revision D
input: WM8962 Beep Generator as /devices/soc0/soc.1/2100000.aips-bus/21a0000.i2c/i2c-0/0-001a/input/input7
imx-wm8962 sound.28: wm8962 <-> 202c000.ssi mapping ok
input: wm8962-audio AMIC as /devices/soc0/sound.28/sound/card0/input8
input: wm8962-audio Headphone Jack as /devices/soc0/sound.28/sound/card0/input9
imx-audio-hdmi sound-hdmi.29: hdmi-hifi <-> hdmi_audio.16 mapping ok
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
VGEN3: disabling
VGEN2: disabling
VGEN1: disabling
vddpu: disabling
input: gpio-keys.27 as /devices/soc0/gpio-keys.27/input/input10
snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 1970-01-02 18:39:07 UTC (153547)
ALSA device list:
#0: wm8962-audio
#1: imx-hdmi-soc
List of all partitions:
1f00 4096 mtdblock0 (driver?)
b300 15634432 mmcblk0 driver: mmcblk
b301 8192 mmcblk0p1 0000bf15-01
b302 749568 mmcblk0p2 0000bf15-02
b308 7757824 mmcblk1 driver: mmcblk
b309 9784 mmcblk1p1 c8f5e20a-01
b30a 19552 mmcblk1p2 c8f5e20a-02
b320 128 mmcblk1rpmb (driver?)
b318 2048 mmcblk1boot1 (driver?)
b310 2048 mmcblk1boot0 (driver?)
No filesystem could mount root, tried: ext3 ext2 ext4 vfat fuseblk
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,10)
CPU2: stopping
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 3.10.17-1.0.0_ga+g2a69800 #1
[<80013b74>] (unwind_backtrace+0x0/0xec) from [<80011590>] (show_stack+0x10/0x14)
[<80011590>] (show_stack+0x10/0x14) from [<80012da0>] (handle_IPI+0x108/0x118)
[<80012da0>] (handle_IPI+0x108/0x118) from [<80008558>] (gic_handle_irq+0x58/0x5c)
[<80008558>] (gic_handle_irq+0x58/0x5c) from [<8000dd00>] (__irq_svc+0x40/0x70)
Exception stack(0xa809df50 to 0xa809df98)
df40: a809df98 3b9aca00 bec50bda 00000000
df60: 80c5811c 80c580d0 8152c130 00000001 bc858537 00000000 a809c000 00000000
df80: 00000017 a809df98 00000009 80444148 00000113 ffffffff
[<8000dd00>] (__irq_svc+0x40/0x70) from [<80444148>] (cpuidle_enter_state+0x54/0xe4)
[<80444148>] (cpuidle_enter_state+0x54/0xe4) from [<80444294>] (cpuidle_idle_call+0xbc/0x154)
[<80444294>] (cpuidle_idle_call+0xbc/0x154) from [<8000ecf0>] (arch_cpu_idle+0x10/0x54)
[<8000ecf0>] (arch_cpu_idle+0x10/0x54) from [<80059c78>] (cpu_startup_entry+0x100/0x14c)
[<80059c78>] (cpu_startup_entry+0x100/0x14c) from [<106287a4>] (0x106287a4)
CPU3: stopping
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 3.10.17-1.0.0_ga+g2a69800 #1
[<80013b74>] (unwind_backtrace+0x0/0xec) from [<80011590>] (show_stack+0x10/0x14)
[<80011590>] (show_stack+0x10/0x14) from [<80012da0>] (handle_IPI+0x108/0x118)
[<80012da0>] (handle_IPI+0x108/0x118) from [<80008558>] (gic_handle_irq+0x58/0x5c)
[<80008558>] (gic_handle_irq+0x58/0x5c) from [<8000dd00>] (__irq_svc+0x40/0x70)
Exception stack(0xa809ff50 to 0xa809ff98)
ff40: a809ff98 3b9aca00 bec50bda 00000000
ff60: 80c5811c 80c580d0 81534130 00000001 bc85744a 00000000 a809e000 00000000
ff80: 00000017 a809ff98 00000009 80444148 00000113 ffffffff
[<8000dd00>] (__irq_svc+0x40/0x70) from [<80444148>] (cpuidle_enter_state+0x54/0xe4)
[<80444148>] (cpuidle_enter_state+0x54/0xe4) from [<80444294>] (cpuidle_idle_call+0xbc/0x154)
[<80444294>] (cpuidle_idle_call+0xbc/0x154) from [<8000ecf0>] (arch_cpu_idle+0x10/0x54)
[<8000ecf0>] (arch_cpu_idle+0x10/0x54) from [<80059c78>] (cpu_startup_entry+0x100/0x14c)
[<80059c78>] (cpu_startup_entry+0x100/0x14c) from [<106287a4>] (0x106287a4)
CPU1: stopping
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.10.17-1.0.0_ga+g2a69800 #1
[<80013b74>] (unwind_backtrace+0x0/0xec) from [<80011590>] (show_stack+0x10/0x14)
[<80011590>] (show_stack+0x10/0x14) from [<80012da0>] (handle_IPI+0x108/0x118)
[<80012da0>] (handle_IPI+0x108/0x118) from [<80008558>] (gic_handle_irq+0x58/0x5c)
[<80008558>] (gic_handle_irq+0x58/0x5c) from [<8000dd00>] (__irq_svc+0x40/0x70)
Exception stack(0xa809bf50 to 0xa809bf98)
bf40: a809bf98 3b9aca00 bec50bda 00000000
bf60: 80c5811c 80c580d0 81524130 00000001 be574262 00000000 a809a000 00000000
bf80: 00000017 a809bf98 00000009 80444148 00000113 ffffffff
[<8000dd00>] (__irq_svc+0x40/0x70) from [<80444148>] (cpuidle_enter_state+0x54/0xe4)
[<80444148>] (cpuidle_enter_state+0x54/0xe4) from [<80444294>] (cpuidle_idle_call+0xbc/0x154)
[<80444294>] (cpuidle_idle_call+0xbc/0x154) from [<8000ecf0>] (arch_cpu_idle+0x10/0x54)
[<8000ecf0>] (arch_cpu_idle+0x10/0x54) from [<80059c78>] (cpu_startup_entry+0x100/0x14c)
[<80059c78>] (cpu_startup_entry+0x100/0x14c) from [<106287a4>] (0x106287a4)
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-23 8:16 Cannot boot after the last update Konstantin Kovalev
@ 2014-07-25 5:21 ` Otavio Salvador
2014-07-25 12:12 ` Konstantin Kovalev
0 siblings, 1 reply; 28+ messages in thread
From: Otavio Salvador @ 2014-07-25 5:21 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale
On Wed, Jul 23, 2014 at 5:16 AM, Konstantin Kovalev
<lepeletie@hotmail.com> wrote:
> I have Freescale Sabre SD board on iMX6q processor.
> ***************************************************
> Build Configuration:
> BB_VERSION = "1.23.1"
> BUILD_SYS = "x86_64-linux"
> NATIVELSBSTRING = "Fedora-20"
> TARGET_SYS = "arm-poky-linux-gnueabi"
> MACHINE = "imx6qsabresd"
> DISTRO = "poky"
> DISTRO_VERSION = "1.6+snapshot-20140723"
> TUNE_FEATURES = "arm armv7a vfp neon callconvention-hard cortexa9"
> TARGET_FPU = "vfp-neon"
> meta
> meta-yocto = "(detachedfrom8b7116d):8b7116d25ed6255a03895d835e5a0560858ab496"
> meta-oe = "(detachedfrom743751e):743751e20cc266143130fb5bb49efb4c86b9e02b"
> meta-fsl-arm = "(detachedfromd900d93):d900d935e1f45a79c7116c4fd290baaa447a870d"
> meta-fsl-arm-extra = "(detachedfromc3b74cd):c3b74cd1de4fba69f14ef6366fdc15f11d32e485"
> meta-fsl-demos = "(nobranch):e60ea240aecbf8fc69c4d18ab6d1361376372c6e"
> ***************************************************
> I use the master-next branch and fsl-image-multimedia-full.
>
> So my problem is that after "repo sync" on last friday I cannot boot the system from the resulting image from my SD-card.
> I have written the image by this command "sudo dd if=fsl-image-multimedia-full-imx6qsabresd.sdcard of=/dev/sdb bs=4M &&sync"
> There are two lines in boot log:
> *******************************************************************
> No filesystem could mount root, tried: ext3 ext2 ext4 vfat fuseblk
> Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,10)
> *******************************************************************
> I attached the full log.
Seems to be an issue with your uSD card or the card reader.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-25 5:21 ` Otavio Salvador
@ 2014-07-25 12:12 ` Konstantin Kovalev
2014-07-25 12:16 ` Otavio Salvador
0 siblings, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-07-25 12:12 UTC (permalink / raw)
To: Otavio Salvador, meta-freescale
[-- Attachment #1: Type: text/plain, Size: 5349 bytes --]
Dear Otavio,
Thanks for your quick response! After some attempts I have found the solution. The problem was in the variable "mmcroot". I've just changed the default value "mmcblk1p2" to "mmcblk0p2" and it works. However, the system stops booting on request "imx6qsabresd login:" and doesn't response on keyboard, touchscreen, and mouse. Unfortunately, my adb console doesn't show any errors on that stage. Probably I did not solve all errors in my u-boot default variables. This is my u-boot environments:
****************************************************************************************************************************************
baudrate=115200
boot_fdt=try
bootcmd=mmc dev ${mmcdev};if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else run netboot; fi
bootdelay=1
bootscript=echo Running bootscript from mmc ...; source
console=ttymxc0
emmcdev=2
ethact=FEC
ethaddr=00:04:9f:02:70:ba
ethprime=FEC
fdt_addr=0x18000000
fdt_file=imx6q-sabresd.dtb
fdt_high=0xffffffff
image=zImage
initrd_high=0xffffffff
ip_dyn=yes
loadaddr=0x12000000
loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};
loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}
loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}
mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot}
mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if run loadfdt; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;
mmcdev=1
mmcpart=2
mmcroot=/dev/mmcblk0p2 rootwait rw
netargs=setenv bootargs console=${console},${baudrate} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp
netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; ${get_cmd} ${image}; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if ${get_cmd} ${fdt_addr} ${fdt_file}; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;
script=boot.scr
update_emmc_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; if ${get_cmd} ${update_sd_firmware_filename}; then if mmc dev ${emmcdev} && mmc open ${emmcdev} 1; then setexpr fw_sz ${filesize} / 0x200; setexpr fw_sz ${fw_sz} + 1; mmc write ${loadaddr} 0x2 ${fw_sz}; mmc close ${emmcdev} 1; fi; fi
update_sd_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; if mmc dev ${mmcdev}; then if ${get_cmd} ${update_sd_firmware_filename}; then setexpr fw_sz ${filesize} / 0x200; setexpr fw_sz ${fw_sz} + 1; mmc write ${loadaddr} 0x2 ${fw_sz}; fi; fi
Environment size: 2275/8188 bytes
****************************************************************************************************************************************
The full boot log is in the attachment.
Best Regards,
Konstantin.
----------------------------------------
> Date: Fri, 25 Jul 2014 02:21:20 -0300
> Subject: Re: [meta-freescale] Cannot boot after the last update...
> From: otavio@ossystems.com.br
> To: lepeletie@hotmail.com
> CC: meta-freescale@yoctoproject.org
>
> On Wed, Jul 23, 2014 at 5:16 AM, Konstantin Kovalev
> <lepeletie@hotmail.com> wrote:
>> I have Freescale Sabre SD board on iMX6q processor.
>> ***************************************************
>> Build Configuration:
>> BB_VERSION = "1.23.1"
>> BUILD_SYS = "x86_64-linux"
>> NATIVELSBSTRING = "Fedora-20"
>> TARGET_SYS = "arm-poky-linux-gnueabi"
>> MACHINE = "imx6qsabresd"
>> DISTRO = "poky"
>> DISTRO_VERSION = "1.6+snapshot-20140723"
>> TUNE_FEATURES = "arm armv7a vfp neon callconvention-hard cortexa9"
>> TARGET_FPU = "vfp-neon"
>> meta
>> meta-yocto = "(detachedfrom8b7116d):8b7116d25ed6255a03895d835e5a0560858ab496"
>> meta-oe = "(detachedfrom743751e):743751e20cc266143130fb5bb49efb4c86b9e02b"
>> meta-fsl-arm = "(detachedfromd900d93):d900d935e1f45a79c7116c4fd290baaa447a870d"
>> meta-fsl-arm-extra = "(detachedfromc3b74cd):c3b74cd1de4fba69f14ef6366fdc15f11d32e485"
>> meta-fsl-demos = "(nobranch):e60ea240aecbf8fc69c4d18ab6d1361376372c6e"
>> ***************************************************
>> I use the master-next branch and fsl-image-multimedia-full.
>>
>> So my problem is that after "repo sync" on last friday I cannot boot the system from the resulting image from my SD-card.
>> I have written the image by this command "sudo dd if=fsl-image-multimedia-full-imx6qsabresd.sdcard of=/dev/sdb bs=4M &&sync"
>> There are two lines in boot log:
>> *******************************************************************
>> No filesystem could mount root, tried: ext3 ext2 ext4 vfat fuseblk
>> Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,10)
>> *******************************************************************
>> I attached the full log.
>
> Seems to be an issue with your uSD card or the card reader.
>
> --
> Otavio Salvador O.S. Systems
> http://www.ossystems.com.br http://code.ossystems.com.br
> Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
[-- Attachment #2: boot_log.txt --]
[-- Type: text/plain, Size: 18780 bytes --]
U-Boot 2014.07 (Jul 22 2014 - 17:06:50)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
auto-detected panel HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
PMIC: PFUZE100 ID=0x10
Net: FEC [PRIME]
Warning: FEC MAC addresses don't match:
Address in SROM is 00:04:9f:02:70:51
Address in environment is 00:04:9f:02:70:ba
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
5290904 bytes read in 257 ms (19.6 MiB/s)
Booting from mmc ...
reading imx6q-sabresd.dtb
47179 bytes read in 21 ms (2.1 MiB/s)
Kernel image @ 0x12000000 [ 0x000000 - 0x50bb98 ]
## Flattened Device Tree blob at 18000000
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800e84a
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 3.10.17-1.0.0_ga+g2a69800 (togran@togran_pc.pdc.vozpp) (gcc version 4.9.0 (GCC) ) #1 SMP PREEMPT Tue Jul 22 14:56:56 MSK 2014
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX6 Quad/DualLite (Device Tree), model: Freescale i.MX6 Quad SABRE Smart Device Board
cma: CMA: reserved 320 MiB at 3c000000
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 8 pages/cpu @8151b000 s8896 r8192 d15680 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1024MB = 1024MB total
Memory: 697660k/697660k available, 350916k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80c0429c (12273 kB)
.init : 0x80c05000 - 0x80c482c0 ( 269 kB)
.data : 0x80c4a000 - 0x80c9abe0 ( 323 kB)
.bss : 0x80c9abe0 - 0x80d03d64 ( 421 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1048576 B
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
CPU identified as i.MX6Q, silicon rev 1.2
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x806323b0 - 0x80632408
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: Booted secondary processor
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: Booted secondary processor
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Use WDOG2 as reset source
syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
vdd1p1: 800 <--> 1375 mV at 1125 mV
vdd3p0: 2800 <--> 3150 mV at 3000 mV
vdd2p5: 2000 <--> 2750 mV at 2425 mV
cpu: 725 <--> 1450 mV at 1100 mV
vddpu: 725 <--> 1450 mV at 1100 mV
vddsoc: 725 <--> 1450 mV at 1175 mV
syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
bio: create slab <bio-0> at 0
mxs-dma 110000.dma-apbh: initialized
usb_otg_vbus: 5000 mV
usb_h1_vbus: 5000 mV
wm8962-supply: no parameters
mipi_dsi_pwr_on: no parameters
sensor-supply: 3300 mV
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c i2c-0: IMX I2C adapter registered
i2c i2c-1: IMX I2C adapter registered
i2c i2c-2: IMX I2C adapter registered
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
pureg-dummy: no parameters
imx6_busfreq busfreq.15: DDR medium rate not supported.
Bus freq driver module loaded
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 2002
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
imx-weim 21b8000.weim: WEIM driver registered.
mxc_mipi_dsi 21e0000.mipi: i.MX MIPI DSI driver probed
MIPI DSI driver module loaded
mxc_sdc_fb fb.30: register mxc display driver ldb
imx-ipuv3 2800000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 128x48
mxc_sdc_fb fb.31: register mxc display driver hdmi
mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1
fbcvt: 1920x1080@60: CVT Name - 2.073M9
mxc_sdc_fb fb.32: register mxc display driver lcd
mxc_sdc_fb fb.32: ipu0-di0 already in use
mxc_sdc_fb: probe of fb.32 failed with error -16
mxc_sdc_fb fb.33: register mxc display driver ldb
imx-sdma 20ec000.sdma: no iram assigned, using external mem
imx-sdma 20ec000.sdma: loaded firmware 1.1
imx-sdma 20ec000.sdma: initialized
pfuze100-regulator 1-0008: Full lay: 1, Metal lay: 1
pfuze100-regulator 1-0008: FAB: 0, FIN: 0
pfuze100-regulator 1-0008: pfuze100 found.
SW1AB: 300 <--> 1875 mV at 1375 mV
SW1C: 300 <--> 1875 mV at 1375 mV
SW2: 800 <--> 3300 mV at 3300 mV
SW3A: 400 <--> 1975 mV at 1500 mV
SW3B: 400 <--> 1975 mV at 1500 mV
SW4: 800 <--> 3300 mV at 3150 mV
SWBST: 5000 <--> 5150 mV at 5000 mV
VSNVS: 1000 <--> 3000 mV at 3000 mV
VREFDDR: 750 mV
VGEN1: 800 <--> 1550 mV at 1500 mV
VGEN2: 800 <--> 1550 mV at 1500 mV
VGEN3: 1800 <--> 3300 mV at 2800 mV
VGEN4: 1800 <--> 3300 mV at 1800 mV
VGEN5: 1800 <--> 3300 mV at 3000 mV
VGEN6: 1800 <--> 3300 mV at 3300 mV
Serial: IMX driver
2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled
serial: Freescale lpuart driver
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
Wait for CR ACK error!
sata phy RX_PLL is stable!
ahci: SSS flag set, parallel bus scan disabled
ahci ahci: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 71
m25p80 spi32766.0: m25p32 (4096 Kbytes)
spi_imx 2008000.ecspi: probed
CAN device driver interface
libphy: fec_enet_mii_bus: probed
fec 2188000.ethernet eth0: registered PHC device 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
usbcore: registered new interface driver usb-storage
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ci_hdrc ci_hdrc.1: doesn't support gadget
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
elan-touch 2-0010: elan - Read Hello Packet Failed
elan-touch: probe of 2-0010 failed with error -22
egalax_ts 1-0004: Failed to read firmware version
egalax_ts: probe of 1-0004 failed with error -5
input: eGalax Touch Screen as /devices/soc0/soc.1/2100000.aips-bus/21a8000.i2c/i2c-2/2-0004/input/input0
input: max11801_ts as /devices/soc0/soc.1/2100000.aips-bus/21a4000.i2c/i2c-1/1-0048/input/input1
input: isl29023 light sensor as /devices/virtual/input/input2
isl29023 2-0044: driver version 1.0 enabled
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
i2c /dev entries driver
ata1: SATA link down (SStatus 0 SControl 300)
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video16
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video17
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video18
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video19
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video20
usb 1-1: new high-speed USB device number 2 using ci_hdrc
mag3110 2-000e: check mag3110 chip ID
input: mag3110 as /devices/virtual/input/input3
mag3110 2-000e: mag3110 is probed
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
input: mma845x as /devices/virtual/input/input4
imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: no vqmmc regulator found
mmc1: no vmmc regulator found
mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
mmc2: no vqmmc regulator found
mmc2: no vmmc regulator found
mmc1: new high speed SDHC card at address 0007
mmcblk0: mmc1:0007 SD16G 14.9 GiB
mmcblk0: p1 p2
mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
usb 1-1.1: new high-speed USB device number 3 using ci_hdrc
hub 1-1.1:1.0: USB hub found
hub 1-1.1:1.0: 4 ports detected
mmc2: new high speed DDR MMC card at address 0001
mmcblk1: mmc2:0001 SEM08G 7.39 GiB
mmcblk1boot0: mmc2:0001 SEM08G partition 1 2.00 MiB
mmcblk1boot1: mmc2:0001 SEM08G partition 2 2.00 MiB
mmcblk1rpmb: mmc2:0001 SEM08G partition 3 128 KiB
mmcblk1: p1 p2
mmcblk1boot1: unknown partition table
mmcblk1boot0: unknown partition table
Galcore version 4.6.9.9754
mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
mxc_asrc 2034000.asrc: mxc_asrc registered
mxc_vpu 2040000.vpu: VPU initialized
leds-gpio leds.20: pins are not configured from the driver
usb 1-1.1.1: new low-speed USB device number 4 using ci_hdrc
caam 2100000.caam: device ID = 0x0a16010000000000 (Era -524)
caam 2100000.caam: job rings = 2, qi = 0
caam 2100000.caam: authenc-hmac-md5-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des-caam
caam 2100000.caam: ecb-des-caam
caam 2100000.caam: ecb-arc4-caam
caam 2100000.caam: ecb-aes-caam
caam 2100000.caam: ctr-aes-caam
caam 2100000.caam: cbc-aes-caam
caam 2100000.caam: ecb-des3-caam
caam 2100000.caam: cbc-3des-caam
caam 2100000.caam: cbc-des-caam
caam 2100000.caam: fsl,sec-v4.0 algorithms registered in /proc/crypto
platform 2101000.jr0: registering rng-caam
platform caam_sm: caam_sm_test: 8-byte key test match OK
platform caam_sm: caam_sm_test: 16-byte key test match OK
platform caam_sm: caam_sm_test: 32-byte key test match OK
platform caam_secvio.40: security violation service handlers armed
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/input/input5
hid-generic 0003:413C:2103.0001: input: USB HID v1.00 Keyboard [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input0
usb 1-1.1.2: new high-speed USB device number 5 using ci_hdrc
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.1/input/input6
hid-generic 0003:413C:2103.0002: input: USB HID v1.10 Mouse [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
i2c-core: driver [cs42888] using legacy suspend method
i2c-core: driver [cs42888] using legacy resume method
wm8962 0-001a: customer id 0 revision D
input: WM8962 Beep Generator as /devices/soc0/soc.1/2100000.aips-bus/21a0000.i2c/i2c-0/0-001a/input/input7
imx-wm8962 sound.28: wm8962 <-> 202c000.ssi mapping ok
input: wm8962-audio AMIC as /devices/soc0/sound.28/sound/card0/input8
input: wm8962-audio Headphone Jack as /devices/soc0/sound.28/sound/card0/input9
imx-audio-hdmi sound-hdmi.29: hdmi-hifi <-> hdmi_audio.16 mapping ok
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
VGEN3: disabling
VGEN2: disabling
VGEN1: disabling
vddpu: disabling
input: gpio-keys.27 as /devices/soc0/gpio-keys.27/input/input10
snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 2014-07-25 07:35:12 UTC (1406273712)
ALSA device list:
#0: wm8962-audio
#1: imx-hdmi-soc
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): recovery complete
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing unused kernel memory: 268K (80c05000 - 80c48000)
INIT: version 2.88 booting
Starting udev
udevd[206]: starting version 182
uvcvideo: Found UVC 1.00 device Live! Cam Connect HD VF0750 (041e:4093)
input: Live! Cam Connect HD VF0750 as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.2/1-1.1.2:1.0/input/input11
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
ov5640_read_reg:write reg error:reg=300a
camera ov5640 is not found
camera ov5640_mipi is found
ERROR: v4l2 capture: slave not found!
usbcore: registered new interface driver snd-usb-audio
ov5642_read_reg:write reg error:reg=300a
camera ov5642 is not found
bootlogd: cannot allocate pseudo tty: No such file or directory
EXT2-fs (mmcblk1p1): warning: mounting unchecked fs, running e2fsck is recommended
FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
ALSA: Restoring mixer settings...
No state is present for card imxhdmisoc
Found hardware: "imx-hdmi-soc" "" "" "" ""
INIT: Entering runlevel: 5
Configuring network interfaces... fec 2188000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.22.1) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
done.
Starting Xserver
Starting system message bus: dbus.
Starting rpcbind daemon...done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ]
Starting Telephony daemon
Starting Linux NFC daemon
Poky (Yocto Project Reference Distro) 1.6+snapshot-20140722 imx6qsabresd /dev/ttymxc0
imx6qsabresd login:
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-25 12:12 ` Konstantin Kovalev
@ 2014-07-25 12:16 ` Otavio Salvador
2014-07-25 12:19 ` Konstantin Kovalev
0 siblings, 1 reply; 28+ messages in thread
From: Otavio Salvador @ 2014-07-25 12:16 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale
On Fri, Jul 25, 2014 at 9:12 AM, Konstantin Kovalev
<lepeletie@hotmail.com> wrote:
> Thanks for your quick response! After some attempts I have found the solution. The problem was in the variable "mmcroot". I've just changed the default value "mmcblk1p2" to "mmcblk0p2" and it works. However, the system stops booting on request "imx6qsabresd login:" and doesn't response on keyboard, touchscreen, and mouse. Unfortunately, my adb console doesn't show any errors on that stage. Probably I did not solve all errors in my u-boot default variables. This is my u-boot environments:
Is it Daisy or master?
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-25 12:16 ` Otavio Salvador
@ 2014-07-25 12:19 ` Konstantin Kovalev
2014-07-25 12:32 ` Otavio Salvador
0 siblings, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-07-25 12:19 UTC (permalink / raw)
To: Otavio Salvador, meta-freescale
Dear Otavio,
Uhmm... Certainly it is "master-next".
******************************************
DISTRO = "poky"
DISTRO_VERSION = "1.6+snapshot-20140725"
******************************************
Best Regards,
Konstantin.
----------------------------------------
> Date: Fri, 25 Jul 2014 09:16:00 -0300
> Subject: Re: [meta-freescale] Cannot boot after the last update...
> From: otavio@ossystems.com.br
> To: lepeletie@hotmail.com
> CC: meta-freescale@yoctoproject.org
>
> On Fri, Jul 25, 2014 at 9:12 AM, Konstantin Kovalev
> <lepeletie@hotmail.com> wrote:
>> Thanks for your quick response! After some attempts I have found the solution. The problem was in the variable "mmcroot". I've just changed the default value "mmcblk1p2" to "mmcblk0p2" and it works. However, the system stops booting on request "imx6qsabresd login:" and doesn't response on keyboard, touchscreen, and mouse. Unfortunately, my adb console doesn't show any errors on that stage. Probably I did not solve all errors in my u-boot default variables. This is my u-boot environments:
>
> Is it Daisy or master?
>
> --
> Otavio Salvador O.S. Systems
> http://www.ossystems.com.br http://code.ossystems.com.br
> Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-25 12:19 ` Konstantin Kovalev
@ 2014-07-25 12:32 ` Otavio Salvador
2014-07-28 6:11 ` Konstantin Kovalev
0 siblings, 1 reply; 28+ messages in thread
From: Otavio Salvador @ 2014-07-25 12:32 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale
On Fri, Jul 25, 2014 at 9:19 AM, Konstantin Kovalev
<lepeletie@hotmail.com> wrote:
> Dear Otavio,
> Uhmm... Certainly it is "master-next".
Please try the pre-build images and confirm it also fails:
http://ci.ossystems.com.br/public/fsl-community-bsp/master/
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-25 12:32 ` Otavio Salvador
@ 2014-07-28 6:11 ` Konstantin Kovalev
2014-07-28 8:10 ` Konstantin Kovalev
0 siblings, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-07-28 6:11 UTC (permalink / raw)
To: Otavio Salvador, meta-freescale
[-- Attachment #1: Type: text/plain, Size: 1408 bytes --]
Dear Otavio,
Sorry for delay. I was outside of my office... So, I have the same issue with this image you wrote about. I mean this "mmcroot=/dev/mmcblk1p2 rootwait rw"
After it was changed to "mmcblk0p2" the system has started to boot. However, it stoped again on this stage:
**************************************************
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
**************************************************
My board is out of network but I am certain that system should continue booting even in that case. So, I guess that there is a problem in "master" branch.
Any ideas?
P.S. Full boot log in attachment.
Best Regards,
Konstantin.
----------------------------------------
> Date: Fri, 25 Jul 2014 09:32:07 -0300
> Subject: Re: [meta-freescale] Cannot boot after the last update...
> From: otavio@ossystems.com.br
> To: lepeletie@hotmail.com
> CC: meta-freescale@yoctoproject.org
>
> On Fri, Jul 25, 2014 at 9:19 AM, Konstantin Kovalev
> <lepeletie@hotmail.com> wrote:
>> Dear Otavio,
>> Uhmm... Certainly it is "master-next".
>
> Please try the pre-build images and confirm it also fails:
>
> http://ci.ossystems.com.br/public/fsl-community-bsp/master/
>
> --
> Otavio Salvador O.S. Systems
> http://www.ossystems.com.br http://code.ossystems.com.br
> Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
[-- Attachment #2: boot_log.txt --]
[-- Type: text/plain, Size: 20564 bytes --]
=> printenv
baudrate=115200
boot_fdt=try
bootcmd=mmc dev ${mmcdev};if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else run netboot; fi
bootdelay=1
bootscript=echo Running bootscript from mmc ...; source
console=ttymxc0
emmcdev=2
ethact=FEC
ethaddr=00:04:9f:02:70:51
ethprime=FEC
fdt_addr=0x18000000
fdt_file=imx6q-sabresd.dtb
fdt_high=0xffffffff
image=zImage
initrd_high=0xffffffff
ip_dyn=yes
loadaddr=0x12000000
loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};
loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}
loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}
mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot}
mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if run loadfdt; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;
mmcdev=1
mmcpart=1
mmcroot=/dev/mmcblk1p2 rootwait rw
netargs=setenv bootargs console=${console},${baudrate} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp
netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; ${get_cmd} ${image}; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if ${get_cmd} ${fdt_addr} ${fdt_file}; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;
script=boot.scr
update_emmc_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; if ${get_cmd} ${update_sd_firmware_filename}; then if mmc dev ${emmcdev} && mmc open ${emmcdev} 1; then setexpr fw_sz ${filesize} / 0x200; setexpr fw_sz ${fw_sz} + 1; mmc write ${loadaddr} 0x2 ${fw_sz}; mmc close ${emmcdev} 1; fi; fi
update_sd_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; if mmc dev ${mmcdev}; then if ${get_cmd} ${update_sd_firmware_filename}; then setexpr fw_sz ${filesize} / 0x200; setexpr fw_sz ${fw_sz} + 1; mmc write ${loadaddr} 0x2 ${fw_sz}; fi; fi
Environment size: 2275/8188 bytes
=> editenv mmcroot
edit: /dev/mmcblk0p2 rootwait rw
=>
=>
=>
=> boot
switch to partitions #0, OK
mmc1 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
5290856 bytes read in 257 ms (19.6 MiB/s)
Booting from mmc ...
reading imx6q-sabresd.dtb
47179 bytes read in 21 ms (2.1 MiB/s)
Kernel image @ 0x12000000 [ 0x000000 - 0x50bb68 ]
## Flattened Device Tree blob at 18000000
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800e84a
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 3.10.17-1.0.0_ga+g2a69800 (jenkins@builder) (gcc version 4.9.0 (GCC) ) #1 SMP PREEMPT Mon Jul 21 23:45:35 UTC 2014
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX6 Quad/DualLite (Device Tree), model: Freescale i.MX6 Quad SABRE Smart Device Board
cma: CMA: reserved 320 MiB at 3c000000
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 8 pages/cpu @8151b000 s8896 r8192 d15680 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1024MB = 1024MB total
Memory: 697660k/697660k available, 350916k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80c0429c (12273 kB)
.init : 0x80c05000 - 0x80c482c0 ( 269 kB)
.data : 0x80c4a000 - 0x80c9abe0 ( 323 kB)
.bss : 0x80c9abe0 - 0x80d03d64 ( 421 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1048576 B
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
CPU identified as i.MX6Q, silicon rev 1.2
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x806323b0 - 0x80632408
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: Booted secondary processor
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: Booted secondary processor
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Use WDOG2 as reset source
syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
vdd1p1: 800 <--> 1375 mV at 1125 mV
vdd3p0: 2800 <--> 3150 mV at 3000 mV
vdd2p5: 2000 <--> 2750 mV at 2425 mV
cpu: 725 <--> 1450 mV at 1100 mV
vddpu: 725 <--> 1450 mV at 1100 mV
vddsoc: 725 <--> 1450 mV at 1175 mV
syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
bio: create slab <bio-0> at 0
mxs-dma 110000.dma-apbh: initialized
usb_otg_vbus: 5000 mV
usb_h1_vbus: 5000 mV
wm8962-supply: no parameters
mipi_dsi_pwr_on: no parameters
sensor-supply: 3300 mV
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c i2c-0: IMX I2C adapter registered
i2c i2c-1: IMX I2C adapter registered
i2c i2c-2: IMX I2C adapter registered
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
pureg-dummy: no parameters
imx6_busfreq busfreq.15: DDR medium rate not supported.
Bus freq driver module loaded
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 2002
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
imx-weim 21b8000.weim: WEIM driver registered.
mxc_mipi_dsi 21e0000.mipi: i.MX MIPI DSI driver probed
MIPI DSI driver module loaded
mxc_sdc_fb fb.30: register mxc display driver ldb
imx-ipuv3 2800000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 128x48
mxc_sdc_fb fb.31: register mxc display driver hdmi
mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1
fbcvt: 1920x1080@60: CVT Name - 2.073M9
mxc_sdc_fb fb.32: register mxc display driver lcd
mxc_sdc_fb fb.32: ipu0-di0 already in use
mxc_sdc_fb: probe of fb.32 failed with error -16
mxc_sdc_fb fb.33: register mxc display driver ldb
imx-sdma 20ec000.sdma: no iram assigned, using external mem
imx-sdma 20ec000.sdma: loaded firmware 1.1
imx-sdma 20ec000.sdma: initialized
pfuze100-regulator 1-0008: Full lay: 1, Metal lay: 1
pfuze100-regulator 1-0008: FAB: 0, FIN: 0
pfuze100-regulator 1-0008: pfuze100 found.
SW1AB: 300 <--> 1875 mV at 1375 mV
SW1C: 300 <--> 1875 mV at 1375 mV
SW2: 800 <--> 3300 mV at 3300 mV
SW3A: 400 <--> 1975 mV at 1500 mV
SW3B: 400 <--> 1975 mV at 1500 mV
SW4: 800 <--> 3300 mV at 3150 mV
SWBST: 5000 <--> 5150 mV at 5000 mV
VSNVS: 1000 <--> 3000 mV at 3000 mV
VREFDDR: 750 mV
VGEN1: 800 <--> 1550 mV at 1500 mV
VGEN2: 800 <--> 1550 mV at 1500 mV
VGEN3: 1800 <--> 3300 mV at 2800 mV
VGEN4: 1800 <--> 3300 mV at 1800 mV
VGEN5: 1800 <--> 3300 mV at 3000 mV
VGEN6: 1800 <--> 3300 mV at 3300 mV
Serial: IMX driver
2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled
serial: Freescale lpuart driver
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
Wait for CR ACK error!
sata phy RX_PLL is stable!
ahci: SSS flag set, parallel bus scan disabled
ahci ahci: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 71
m25p80 spi32766.0: m25p32 (4096 Kbytes)
spi_imx 2008000.ecspi: probed
CAN device driver interface
libphy: fec_enet_mii_bus: probed
fec 2188000.ethernet eth0: registered PHC device 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
usbcore: registered new interface driver usb-storage
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ci_hdrc ci_hdrc.1: doesn't support gadget
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
elan-touch 2-0010: elan - Read Hello Packet Failed
elan-touch: probe of 2-0010 failed with error -22
egalax_ts 1-0004: Failed to read firmware version
egalax_ts: probe of 1-0004 failed with error -5
input: eGalax Touch Screen as /devices/soc0/soc.1/2100000.aips-bus/21a8000.i2c/i2c-2/2-0004/input/input0
input: max11801_ts as /devices/soc0/soc.1/2100000.aips-bus/21a4000.i2c/i2c-1/1-0048/input/input1
input: isl29023 light sensor as /devices/virtual/input/input2
isl29023 2-0044: driver version 1.0 enabled
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
i2c /dev entries driver
ata1: SATA link down (SStatus 0 SControl 300)
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video16
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video17
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video18
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video19
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video20
usb 1-1: new high-speed USB device number 2 using ci_hdrc
mag3110 2-000e: check mag3110 chip ID
input: mag3110 as /devices/virtual/input/input3
mag3110 2-000e: mag3110 is probed
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
input: mma845x as /devices/virtual/input/input4
imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: no vqmmc regulator found
mmc1: no vmmc regulator found
mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
mmc2: no vqmmc regulator found
mmc2: no vmmc regulator found
mmc1: new high speed SDHC card at address 0007
mmcblk0: mmc1:0007 SD16G 14.9 GiB
mmcblk0: p1 p2
mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
usb 1-1.1: new high-speed USB device number 3 using ci_hdrc
hub 1-1.1:1.0: USB hub found
hub 1-1.1:1.0: 4 ports detected
mmc2: new high speed DDR MMC card at address 0001
mmcblk1: mmc2:0001 SEM08G 7.39 GiB
mmcblk1boot0: mmc2:0001 SEM08G partition 1 2.00 MiB
mmcblk1boot1: mmc2:0001 SEM08G partition 2 2.00 MiB
mmcblk1rpmb: mmc2:0001 SEM08G partition 3 128 KiB
mmcblk1: p1 p2
mmcblk1boot1: unknown partition table
mmcblk1boot0: unknown partition table
Galcore version 4.6.9.9754
mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
mxc_asrc 2034000.asrc: mxc_asrc registered
mxc_vpu 2040000.vpu: VPU initialized
leds-gpio leds.20: pins are not configured from the driver
caam 2100000.caam: device ID = 0x0a16010000000000 (Era -524)
caam 2100000.caam: job rings = 2, qi = 0
caam 2100000.caam: authenc-hmac-md5-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des3_ede-caam
usb 1-1.1.1: new low-speed USB device number 4 using ci_hdrc
caam 2100000.caam: authencesn-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des-caam
caam 2100000.caam: ecb-des-caam
caam 2100000.caam: ecb-arc4-caam
caam 2100000.caam: ecb-aes-caam
caam 2100000.caam: ctr-aes-caam
caam 2100000.caam: cbc-aes-caam
caam 2100000.caam: ecb-des3-caam
caam 2100000.caam: cbc-3des-caam
caam 2100000.caam: cbc-des-caam
caam 2100000.caam: fsl,sec-v4.0 algorithms registered in /proc/crypto
platform 2101000.jr0: registering rng-caam
platform caam_sm: caam_sm_test: 8-byte key test match OK
platform caam_sm: caam_sm_test: 16-byte key test match OK
platform caam_sm: caam_sm_test: 32-byte key test match OK
platform caam_secvio.40: security violation service handlers armed
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
i2c-core: driver [cs42888] using legacy suspend method
i2c-core: driver [cs42888] using legacy resume method
wm8962 0-001a: customer id 0 revision D
input: WM8962 Beep Generator as /devices/soc0/soc.1/2100000.aips-bus/21a0000.i2c/i2c-0/0-001a/input/input5
imx-wm8962 sound.28: wm8962 <-> 202c000.ssi mapping ok
input: wm8962-audio AMIC as /devices/soc0/sound.28/sound/card0/input6
input: wm8962-audio Headphone Jack as /devices/soc0/sound.28/sound/card0/input7
imx-audio-hdmi sound-hdmi.29: hdmi-hifi <-> hdmi_audio.16 mapping ok
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/input/input8
hid-generic 0003:413C:2103.0001: input: USB HID v1.00 Keyboard [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input0
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.1/input/input9
hid-generic 0003:413C:2103.0002: input: USB HID v1.10 Mouse [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input1
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
usb 1-1.1.2: new high-speed USB device number 5 using ci_hdrc
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
VGEN3: disabling
VGEN2: disabling
VGEN1: disabling
vddpu: disabling
input: gpio-keys.27 as /devices/soc0/gpio-keys.27/input/input10
snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 2014-07-28 02:00:24 UTC (1406512824)
ALSA device list:
#0: wm8962-audio
#1: imx-hdmi-soc
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing unused kernel memory: 268K (80c05000 - 80c48000)
INIT: version 2.88 booting
Starting udev
udevd[202]: starting version 182
uvcvideo: Found UVC 1.00 device Live! Cam Connect HD VF0750 (041e:4093)
input: Live! Cam Connect HD VF0750 as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.2/1-1.1.2:1.0/input/input11
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
usbcore: registered new interface driver snd-usb-audio
ov5640_read_reg:write reg error:reg=300a
camera ov5640 is not found
camera ov5640_mipi is found
ov5642_read_reg:write reg error:reg=300a
camera ov5642 is not found
ERROR: v4l2 capture: slave not found!
EXT4-fs (mmcblk1p1): warning: mounting unchecked fs, running e2fsck is recommended
EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
bootlogd: cannot allocate pseudo tty: No such file or directory
Populating dev cache
ALSA: Restoring mixer settings...
No state is present for card imxhdmisoc
Found hardware: "imx-hdmi-soc" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card imxhdmisoc
No state is present for card VF0750
Found hardware: "USB-Audio" "USB Mixer" "USB041e:4093" "" ""
INIT: Entering runlevel: 5
Configuring network interfaces... fec 2188000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.22.1) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
done.
Starting Xserver
Starting system message bus: dbus.
Starting rpcbind daemon...done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-28 6:11 ` Konstantin Kovalev
@ 2014-07-28 8:10 ` Konstantin Kovalev
2014-07-28 13:28 ` Otavio Salvador
0 siblings, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-07-28 8:10 UTC (permalink / raw)
To: Otavio Salvador, meta-freescale
[-- Attachment #1: Type: text/plain, Size: 2496 bytes --]
Dear Otavio,
It seems funny but after I saved the u-boot environment and restarted the board few times the system stopped on this stage:
******************************************
Running local boot scripts (/etc/rc.local).
Poky (Yocto Project Reference Distro) 1.6+snapshot-20140721 imx6qsabresd /dev/ttymxc0
imx6qsabresd login:
******************************************
Now I am completely confused. The system doesn't respond on any input (mouse, keyboard, touchscreen) and I can't see anything on the display.
New boot log is attached because of some differences in comparing with the old one.
So, I really need help!
Best Regards,
Konstantin.
----------------------------------------
From: lepeletie@hotmail.com
To: otavio@ossystems.com.br; meta-freescale@yoctoproject.org
Date: Mon, 28 Jul 2014 10:11:47 +0400
Subject: Re: [meta-freescale] Cannot boot after the last update...
Dear Otavio,
Sorry for delay. I was outside of my office... So, I have the same issue with this image you wrote about. I mean this "mmcroot=/dev/mmcblk1p2 rootwait rw"
After it was changed to "mmcblk0p2" the system has started to boot. However, it stoped again on this stage:
**************************************************
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
**************************************************
My board is out of network but I am certain that system should continue booting even in that case. So, I guess that there is a problem in "master" branch.
Any ideas?
P.S. Full boot log in attachment.
Best Regards,
Konstantin.
----------------------------------------
> Date: Fri, 25 Jul 2014 09:32:07 -0300
> Subject: Re: [meta-freescale] Cannot boot after the last update...
> From: otavio@ossystems.com.br
> To: lepeletie@hotmail.com
> CC: meta-freescale@yoctoproject.org
>
> On Fri, Jul 25, 2014 at 9:19 AM, Konstantin Kovalev
> <lepeletie@hotmail.com> wrote:
>> Dear Otavio,
>> Uhmm... Certainly it is "master-next".
>
> Please try the pre-build images and confirm it also fails:
>
> http://ci.ossystems.com.br/public/fsl-community-bsp/master/
>
> --
> Otavio Salvador O.S. Systems
> http://www.ossystems.com.br http://code.ossystems.com.br
> Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
--
_______________________________________________
meta-freescale mailing list
meta-freescale@yoctoproject.org
https://lists.yoctoproject.org/listinfo/meta-freescale
[-- Attachment #2: boot_log.txt --]
[-- Type: text/plain, Size: 18986 bytes --]
U-Boot 2014.07 (Jul 22 2014 - 00:23:28)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
auto-detected panel HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
PMIC: PFUZE100 ID=0x10
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
5290856 bytes read in 258 ms (19.6 MiB/s)
Booting from mmc ...
reading imx6q-sabresd.dtb
47179 bytes read in 20 ms (2.2 MiB/s)
Kernel image @ 0x12000000 [ 0x000000 - 0x50bb68 ]
## Flattened Device Tree blob at 18000000
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800e84a
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 3.10.17-1.0.0_ga+g2a69800 (jenkins@builder) (gcc version 4.9.0 (GCC) ) #1 SMP PREEMPT Mon Jul 21 23:45:35 UTC 2014
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX6 Quad/DualLite (Device Tree), model: Freescale i.MX6 Quad SABRE Smart Device Board
cma: CMA: reserved 320 MiB at 3c000000
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 8 pages/cpu @8151b000 s8896 r8192 d15680 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1024MB = 1024MB total
Memory: 697660k/697660k available, 350916k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80c0429c (12273 kB)
.init : 0x80c05000 - 0x80c482c0 ( 269 kB)
.data : 0x80c4a000 - 0x80c9abe0 ( 323 kB)
.bss : 0x80c9abe0 - 0x80d03d64 ( 421 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1048576 B
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
CPU identified as i.MX6Q, silicon rev 1.2
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x806323b0 - 0x80632408
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: Booted secondary processor
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: Booted secondary processor
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Use WDOG2 as reset source
syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
vdd1p1: 800 <--> 1375 mV at 1125 mV
vdd3p0: 2800 <--> 3150 mV at 3000 mV
vdd2p5: 2000 <--> 2750 mV at 2425 mV
cpu: 725 <--> 1450 mV at 1100 mV
vddpu: 725 <--> 1450 mV at 1100 mV
vddsoc: 725 <--> 1450 mV at 1175 mV
syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
bio: create slab <bio-0> at 0
mxs-dma 110000.dma-apbh: initialized
usb_otg_vbus: 5000 mV
usb_h1_vbus: 5000 mV
wm8962-supply: no parameters
mipi_dsi_pwr_on: no parameters
sensor-supply: 3300 mV
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c i2c-0: IMX I2C adapter registered
i2c i2c-1: IMX I2C adapter registered
i2c i2c-2: IMX I2C adapter registered
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
pureg-dummy: no parameters
imx6_busfreq busfreq.15: DDR medium rate not supported.
Bus freq driver module loaded
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 2002
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
imx-weim 21b8000.weim: WEIM driver registered.
mxc_mipi_dsi 21e0000.mipi: i.MX MIPI DSI driver probed
MIPI DSI driver module loaded
mxc_sdc_fb fb.30: register mxc display driver ldb
imx-ipuv3 2800000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 128x48
mxc_sdc_fb fb.31: register mxc display driver hdmi
mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1
fbcvt: 1920x1080@60: CVT Name - 2.073M9
mxc_sdc_fb fb.32: register mxc display driver lcd
mxc_sdc_fb fb.32: ipu0-di0 already in use
mxc_sdc_fb: probe of fb.32 failed with error -16
mxc_sdc_fb fb.33: register mxc display driver ldb
imx-sdma 20ec000.sdma: no iram assigned, using external mem
imx-sdma 20ec000.sdma: loaded firmware 1.1
imx-sdma 20ec000.sdma: initialized
pfuze100-regulator 1-0008: Full lay: 1, Metal lay: 1
pfuze100-regulator 1-0008: FAB: 0, FIN: 0
pfuze100-regulator 1-0008: pfuze100 found.
SW1AB: 300 <--> 1875 mV at 1375 mV
SW1C: 300 <--> 1875 mV at 1375 mV
SW2: 800 <--> 3300 mV at 3300 mV
SW3A: 400 <--> 1975 mV at 1500 mV
SW3B: 400 <--> 1975 mV at 1500 mV
SW4: 800 <--> 3300 mV at 3150 mV
SWBST: 5000 <--> 5150 mV at 5000 mV
VSNVS: 1000 <--> 3000 mV at 3000 mV
VREFDDR: 750 mV
VGEN1: 800 <--> 1550 mV at 1500 mV
VGEN2: 800 <--> 1550 mV at 1500 mV
VGEN3: 1800 <--> 3300 mV at 2800 mV
VGEN4: 1800 <--> 3300 mV at 1800 mV
VGEN5: 1800 <--> 3300 mV at 3000 mV
VGEN6: 1800 <--> 3300 mV at 3300 mV
Serial: IMX driver
2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled
serial: Freescale lpuart driver
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
Wait for CR ACK error!
sata phy RX_PLL is stable!
ahci: SSS flag set, parallel bus scan disabled
ahci ahci: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 71
m25p80 spi32766.0: m25p32 (4096 Kbytes)
spi_imx 2008000.ecspi: probed
CAN device driver interface
libphy: fec_enet_mii_bus: probed
fec 2188000.ethernet eth0: registered PHC device 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
usbcore: registered new interface driver usb-storage
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ci_hdrc ci_hdrc.1: doesn't support gadget
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
elan-touch 2-0010: elan - Read Hello Packet Failed
elan-touch: probe of 2-0010 failed with error -22
egalax_ts 1-0004: Failed to read firmware version
egalax_ts: probe of 1-0004 failed with error -5
input: eGalax Touch Screen as /devices/soc0/soc.1/2100000.aips-bus/21a8000.i2c/i2c-2/2-0004/input/input0
input: max11801_ts as /devices/soc0/soc.1/2100000.aips-bus/21a4000.i2c/i2c-1/1-0048/input/input1
input: isl29023 light sensor as /devices/virtual/input/input2
isl29023 2-0044: driver version 1.0 enabled
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
i2c /dev entries driver
ata1: SATA link down (SStatus 0 SControl 300)
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video16
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video17
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video18
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video19
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video20
usb 1-1: new high-speed USB device number 2 using ci_hdrc
mag3110 2-000e: check mag3110 chip ID
input: mag3110 as /devices/virtual/input/input3
mag3110 2-000e: mag3110 is probed
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
input: mma845x as /devices/virtual/input/input4
imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: no vqmmc regulator found
mmc1: no vmmc regulator found
mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
mmc2: no vqmmc regulator found
mmc2: no vmmc regulator found
mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
mmc1: new high speed SDHC card at address 0007
mmcblk0: mmc1:0007 SD16G 14.9 GiB
mmcblk0: p1 p2
usb 1-1.1: new high-speed USB device number 3 using ci_hdrc
hub 1-1.1:1.0: USB hub found
hub 1-1.1:1.0: 4 ports detected
mmc2: new high speed DDR MMC card at address 0001
mmcblk1: mmc2:0001 SEM08G 7.39 GiB
mmcblk1boot0: mmc2:0001 SEM08G partition 1 2.00 MiB
mmcblk1boot1: mmc2:0001 SEM08G partition 2 2.00 MiB
mmcblk1rpmb: mmc2:0001 SEM08G partition 3 128 KiB
mmcblk1: p1 p2
mmcblk1boot1: unknown partition table
mmcblk1boot0: unknown partition table
Galcore version 4.6.9.9754
mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
mxc_asrc 2034000.asrc: mxc_asrc registered
mxc_vpu 2040000.vpu: VPU initialized
leds-gpio leds.20: pins are not configured from the driver
usb 1-1.1.1: new low-speed USB device number 4 using ci_hdrc
caam 2100000.caam: device ID = 0x0a16010000000000 (Era -524)
caam 2100000.caam: job rings = 2, qi = 0
caam 2100000.caam: authenc-hmac-md5-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des-caam
caam 2100000.caam: ecb-des-caam
caam 2100000.caam: ecb-arc4-caam
caam 2100000.caam: ecb-aes-caam
caam 2100000.caam: ctr-aes-caam
caam 2100000.caam: cbc-aes-caam
caam 2100000.caam: ecb-des3-caam
caam 2100000.caam: cbc-3des-caam
caam 2100000.caam: cbc-des-caam
caam 2100000.caam: fsl,sec-v4.0 algorithms registered in /proc/crypto
platform 2101000.jr0: registering rng-caam
platform caam_sm: caam_sm_test: 8-byte key test match OK
platform caam_sm: caam_sm_test: 16-byte key test match OK
platform caam_sm: caam_sm_test: 32-byte key test match OK
platform caam_secvio.40: security violation service handlers armed
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/input/input5
hid-generic 0003:413C:2103.0001: input: USB HID v1.00 Keyboard [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input0
usb 1-1.1.2: new high-speed USB device number 5 using ci_hdrc
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.1/input/input6
hid-generic 0003:413C:2103.0002: input: USB HID v1.10 Mouse [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
i2c-core: driver [cs42888] using legacy suspend method
i2c-core: driver [cs42888] using legacy resume method
wm8962 0-001a: customer id 0 revision D
input: WM8962 Beep Generator as /devices/soc0/soc.1/2100000.aips-bus/21a0000.i2c/i2c-0/0-001a/input/input7
imx-wm8962 sound.28: wm8962 <-> 202c000.ssi mapping ok
input: wm8962-audio AMIC as /devices/soc0/sound.28/sound/card0/input8
input: wm8962-audio Headphone Jack as /devices/soc0/sound.28/sound/card0/input9
imx-audio-hdmi sound-hdmi.29: hdmi-hifi <-> hdmi_audio.16 mapping ok
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
VGEN3: disabling
VGEN2: disabling
VGEN1: disabling
vddpu: disabling
input: gpio-keys.27 as /devices/soc0/gpio-keys.27/input/input10
snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 2014-07-28 03:57:35 UTC (1406519855)
ALSA device list:
#0: wm8962-audio
#1: imx-hdmi-soc
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): recovery complete
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing unused kernel memory: 268K (80c05000 - 80c48000)
INIT: version 2.88 booting
Starting udev
udevd[206]: starting version 182
ov5640_read_reg:write reg error:reg=300a
camera ov5640 is not found
usbcore: registered new interface driver snd-usb-audio
uvcvideo: Found UVC 1.00 device Live! Cam Connect HD VF0750 (041e:4093)
input: Live! Cam Connect HD VF0750 as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.2/1-1.1.2:1.0/input/input11
ERROR: v4l2 capture: slave not found!
ERROR: v4l2 capture: slave not found!
ov5642_read_reg:write reg error:reg=300a
camera ov5642 is not found
camera ov5640_mipi is found
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
bootlogd: cannot allocate pseudo tty: No such file or directory
EXT4-fs (mmcblk1p1): warning: mounting unchecked fs, running e2fsck is recommended
EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
ALSA: Restoring mixer settings...
No state is present for card imxhdmisoc
Found hardware: "imx-hdmi-soc" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card imxhdmisoc
No state is present for card VF0750
Found hardware: "USB-Audio" "USB Mixer" "USB041e:4093" "" ""
INIT: Entering runlevel: 5
Configuring network interfaces... fec 2188000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.22.1) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
done.
Starting Xserver
Starting system message bus: dbus.
Starting rpcbind daemon...done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
...done.
Starting Telephony daemon
Starting Linux NFC daemon
Starting OProfileUI server
Running local boot scripts (/etc/rc.local).
Poky (Yocto Project Reference Distro) 1.6+snapshot-20140721 imx6qsabresd /dev/ttymxc0
imx6qsabresd login:
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-28 8:10 ` Konstantin Kovalev
@ 2014-07-28 13:28 ` Otavio Salvador
2014-07-28 13:36 ` Konstantin Kovalev
0 siblings, 1 reply; 28+ messages in thread
From: Otavio Salvador @ 2014-07-28 13:28 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale
On Mon, Jul 28, 2014 at 5:10 AM, Konstantin Kovalev
<lepeletie@hotmail.com> wrote:
> It seems funny but after I saved the u-boot environment and restarted the board few times the system stopped on this stage:
> ******************************************
> Running local boot scripts (/etc/rc.local).
>
> Poky (Yocto Project Reference Distro) 1.6+snapshot-20140721 imx6qsabresd /dev/ttymxc0
>
> imx6qsabresd login:
> ******************************************
> Now I am completely confused. The system doesn't respond on any input (mouse, keyboard, touchscreen) and I can't see anything on the display.
> New boot log is attached because of some differences in comparing with the old one.
Please paste the full bootlog so we can see it.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-28 13:28 ` Otavio Salvador
@ 2014-07-28 13:36 ` Konstantin Kovalev
2014-07-28 14:12 ` Daiane Angolini
0 siblings, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-07-28 13:36 UTC (permalink / raw)
To: Otavio Salvador, meta-freescale
Dear Otavio,
It was in attachment but OK:
**************************************************************************************
U-Boot 2014.07 (Jul 22 2014 - 00:23:28)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
auto-detected panel HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
PMIC: PFUZE100 ID=0x10
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
5290856 bytes read in 258 ms (19.6 MiB/s)
Booting from mmc ...
reading imx6q-sabresd.dtb
47179 bytes read in 20 ms (2.2 MiB/s)
Kernel image @ 0x12000000 [ 0x000000 - 0x50bb68 ]
## Flattened Device Tree blob at 18000000
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800e84a
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 3.10.17-1.0.0_ga+g2a69800 (jenkins@builder) (gcc version 4.9.0 (GCC) ) #1 SMP PREEMPT Mon Jul 21 23:45:35 UTC 2014
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX6 Quad/DualLite (Device Tree), model: Freescale i.MX6 Quad SABRE Smart Device Board
cma: CMA: reserved 320 MiB at 3c000000
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 8 pages/cpu @8151b000 s8896 r8192 d15680 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1024MB = 1024MB total
Memory: 697660k/697660k available, 350916k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80c0429c (12273 kB)
.init : 0x80c05000 - 0x80c482c0 ( 269 kB)
.data : 0x80c4a000 - 0x80c9abe0 ( 323 kB)
.bss : 0x80c9abe0 - 0x80d03d64 ( 421 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1048576 B
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
CPU identified as i.MX6Q, silicon rev 1.2
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x806323b0 - 0x80632408
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: Booted secondary processor
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: Booted secondary processor
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Use WDOG2 as reset source
syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
vdd1p1: 800 <--> 1375 mV at 1125 mV
vdd3p0: 2800 <--> 3150 mV at 3000 mV
vdd2p5: 2000 <--> 2750 mV at 2425 mV
cpu: 725 <--> 1450 mV at 1100 mV
vddpu: 725 <--> 1450 mV at 1100 mV
vddsoc: 725 <--> 1450 mV at 1175 mV
syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
bio: create slab <bio-0> at 0
mxs-dma 110000.dma-apbh: initialized
usb_otg_vbus: 5000 mV
usb_h1_vbus: 5000 mV
wm8962-supply: no parameters
mipi_dsi_pwr_on: no parameters
sensor-supply: 3300 mV
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c i2c-0: IMX I2C adapter registered
i2c i2c-1: IMX I2C adapter registered
i2c i2c-2: IMX I2C adapter registered
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
pureg-dummy: no parameters
imx6_busfreq busfreq.15: DDR medium rate not supported.
Bus freq driver module loaded
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 2002
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
imx-weim 21b8000.weim: WEIM driver registered.
mxc_mipi_dsi 21e0000.mipi: i.MX MIPI DSI driver probed
MIPI DSI driver module loaded
mxc_sdc_fb fb.30: register mxc display driver ldb
imx-ipuv3 2800000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 128x48
mxc_sdc_fb fb.31: register mxc display driver hdmi
mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1
fbcvt: 1920x1080@60: CVT Name - 2.073M9
mxc_sdc_fb fb.32: register mxc display driver lcd
mxc_sdc_fb fb.32: ipu0-di0 already in use
mxc_sdc_fb: probe of fb.32 failed with error -16
mxc_sdc_fb fb.33: register mxc display driver ldb
imx-sdma 20ec000.sdma: no iram assigned, using external mem
imx-sdma 20ec000.sdma: loaded firmware 1.1
imx-sdma 20ec000.sdma: initialized
pfuze100-regulator 1-0008: Full lay: 1, Metal lay: 1
pfuze100-regulator 1-0008: FAB: 0, FIN: 0
pfuze100-regulator 1-0008: pfuze100 found.
SW1AB: 300 <--> 1875 mV at 1375 mV
SW1C: 300 <--> 1875 mV at 1375 mV
SW2: 800 <--> 3300 mV at 3300 mV
SW3A: 400 <--> 1975 mV at 1500 mV
SW3B: 400 <--> 1975 mV at 1500 mV
SW4: 800 <--> 3300 mV at 3150 mV
SWBST: 5000 <--> 5150 mV at 5000 mV
VSNVS: 1000 <--> 3000 mV at 3000 mV
VREFDDR: 750 mV
VGEN1: 800 <--> 1550 mV at 1500 mV
VGEN2: 800 <--> 1550 mV at 1500 mV
VGEN3: 1800 <--> 3300 mV at 2800 mV
VGEN4: 1800 <--> 3300 mV at 1800 mV
VGEN5: 1800 <--> 3300 mV at 3000 mV
VGEN6: 1800 <--> 3300 mV at 3300 mV
Serial: IMX driver
2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled
serial: Freescale lpuart driver
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
Wait for CR ACK error!
sata phy RX_PLL is stable!
ahci: SSS flag set, parallel bus scan disabled
ahci ahci: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 71
m25p80 spi32766.0: m25p32 (4096 Kbytes)
spi_imx 2008000.ecspi: probed
CAN device driver interface
libphy: fec_enet_mii_bus: probed
fec 2188000.ethernet eth0: registered PHC device 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
usbcore: registered new interface driver usb-storage
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ci_hdrc ci_hdrc.1: doesn't support gadget
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
elan-touch 2-0010: elan - Read Hello Packet Failed
elan-touch: probe of 2-0010 failed with error -22
egalax_ts 1-0004: Failed to read firmware version
egalax_ts: probe of 1-0004 failed with error -5
input: eGalax Touch Screen as /devices/soc0/soc.1/2100000.aips-bus/21a8000.i2c/i2c-2/2-0004/input/input0
input: max11801_ts as /devices/soc0/soc.1/2100000.aips-bus/21a4000.i2c/i2c-1/1-0048/input/input1
input: isl29023 light sensor as /devices/virtual/input/input2
isl29023 2-0044: driver version 1.0 enabled
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
i2c /dev entries driver
ata1: SATA link down (SStatus 0 SControl 300)
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video16
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video17
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video18
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video19
mxc_v4l2_output v4l2_out.38: V4L2 device registered as video20
usb 1-1: new high-speed USB device number 2 using ci_hdrc
mag3110 2-000e: check mag3110 chip ID
input: mag3110 as /devices/virtual/input/input3
mag3110 2-000e: mag3110 is probed
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
input: mma845x as /devices/virtual/input/input4
imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: no vqmmc regulator found
mmc1: no vmmc regulator found
mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
mmc2: no vqmmc regulator found
mmc2: no vmmc regulator found
mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
mmc1: new high speed SDHC card at address 0007
mmcblk0: mmc1:0007 SD16G 14.9 GiB
mmcblk0: p1 p2
usb 1-1.1: new high-speed USB device number 3 using ci_hdrc
hub 1-1.1:1.0: USB hub found
hub 1-1.1:1.0: 4 ports detected
mmc2: new high speed DDR MMC card at address 0001
mmcblk1: mmc2:0001 SEM08G 7.39 GiB
mmcblk1boot0: mmc2:0001 SEM08G partition 1 2.00 MiB
mmcblk1boot1: mmc2:0001 SEM08G partition 2 2.00 MiB
mmcblk1rpmb: mmc2:0001 SEM08G partition 3 128 KiB
mmcblk1: p1 p2
mmcblk1boot1: unknown partition table
mmcblk1boot0: unknown partition table
Galcore version 4.6.9.9754
mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
mxc_asrc 2034000.asrc: mxc_asrc registered
mxc_vpu 2040000.vpu: VPU initialized
leds-gpio leds.20: pins are not configured from the driver
usb 1-1.1.1: new low-speed USB device number 4 using ci_hdrc
caam 2100000.caam: device ID = 0x0a16010000000000 (Era -524)
caam 2100000.caam: job rings = 2, qi = 0
caam 2100000.caam: authenc-hmac-md5-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des-caam
caam 2100000.caam: ecb-des-caam
caam 2100000.caam: ecb-arc4-caam
caam 2100000.caam: ecb-aes-caam
caam 2100000.caam: ctr-aes-caam
caam 2100000.caam: cbc-aes-caam
caam 2100000.caam: ecb-des3-caam
caam 2100000.caam: cbc-3des-caam
caam 2100000.caam: cbc-des-caam
caam 2100000.caam: fsl,sec-v4.0 algorithms registered in /proc/crypto
platform 2101000.jr0: registering rng-caam
platform caam_sm: caam_sm_test: 8-byte key test match OK
platform caam_sm: caam_sm_test: 16-byte key test match OK
platform caam_sm: caam_sm_test: 32-byte key test match OK
platform caam_secvio.40: security violation service handlers armed
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/input/input5
usb 1-1.1.2: new high-speed USB device number 5 using ci_hdrc
hid-generic 0003:413C:2103.0001: input: USB HID v1.00 Keyboard [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input0
input: LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.1/input/input6
hid-generic 0003:413C:2103.0002: input: USB HID v1.10 Mouse [LITE-ON Technology Dell USB/PS2 Combo Rackmount Keyboard] on usb-ci_hdrc.0-1.1.1/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
i2c-core: driver [cs42888] using legacy suspend method
i2c-core: driver [cs42888] using legacy resume method
wm8962 0-001a: customer id 0 revision D
input: WM8962 Beep Generator as /devices/soc0/soc.1/2100000.aips-bus/21a0000.i2c/i2c-0/0-001a/input/input7
imx-wm8962 sound.28: wm8962 <-> 202c000.ssi mapping ok
input: wm8962-audio AMIC as /devices/soc0/sound.28/sound/card0/input8
input: wm8962-audio Headphone Jack as /devices/soc0/sound.28/sound/card0/input9
imx-audio-hdmi sound-hdmi.29: hdmi-hifi <-> hdmi_audio.16 mapping ok
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
VGEN3: disabling
VGEN2: disabling
VGEN1: disabling
vddpu: disabling
input: gpio-keys.27 as /devices/soc0/gpio-keys.27/input/input10
snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 2014-07-28 09:45:44 UTC (1406540744)
ALSA device list:
#0: wm8962-audio
#1: imx-hdmi-soc
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): recovery complete
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing unused kernel memory: 268K (80c05000 - 80c48000)
INIT: version 2.88 booting
Starting udev
udevd[206]: starting version 182
camera ov5640_mipi is found
uvcvideo: Found UVC 1.00 device Live! Cam Connect HD VF0750 (041e:4093)
input: Live! Cam Connect HD VF0750 as /devices/soc0/soc.1/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1.2/1-1.1.2:1.0/input/input11
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
usbcore: registered new interface driver snd-usb-audio
ERROR: v4l2 capture: slave not found!
ov5640_read_reg:write reg error:reg=300a
camera ov5640 is not found
bootlogd: cannot allocate pseudo tty: No such file or directory
ov5642_read_reg:write reg error:reg=300a
camera ov5642 is not found
EXT4-fs (mmcblk1p1): warning: mounting unchecked fs, running e2fsck is recommended
EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
ALSA: Restoring mixer settings...
No state is present for card imxhdmisoc
Found hardware: "imx-hdmi-soc" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card imxhdmisoc
No state is present for card VF0750
Found hardware: "USB-Audio" "USB Mixer" "USB041e:4093" "" ""
Hardware is initialized using a generic method
No state is present for card VF0750
INIT: Entering runlevel: 5
Configuring network interfaces... fec 2188000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.22.1) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
done.
Starting Xserver
Starting system message bus: dbus.
Starting rpcbind daemon...done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
...done.
Starting Telephony daemon
Starting Linux NFC daemon
Starting OProfileUI server
Running local boot scripts (/etc/rc.local).
Poky (Yocto Project Reference Distro) 1.6+snapshot-20140721 imx6qsabresd /dev/ttymxc0
imx6qsabresd login:
*************************************************************************
Best Regards,
Konstantin.
----------------------------------------
> Date: Mon, 28 Jul 2014 10:28:42 -0300
> Subject: Re: [meta-freescale] Cannot boot after the last update...
> From: otavio@ossystems.com.br
> To: lepeletie@hotmail.com
> CC: meta-freescale@yoctoproject.org
>
> On Mon, Jul 28, 2014 at 5:10 AM, Konstantin Kovalev
> <lepeletie@hotmail.com> wrote:
>> It seems funny but after I saved the u-boot environment and restarted the board few times the system stopped on this stage:
>> ******************************************
>> Running local boot scripts (/etc/rc.local).
>>
>> Poky (Yocto Project Reference Distro) 1.6+snapshot-20140721 imx6qsabresd /dev/ttymxc0
>>
>> imx6qsabresd login:
>> ******************************************
>> Now I am completely confused. The system doesn't respond on any input (mouse, keyboard, touchscreen) and I can't see anything on the display.
>> New boot log is attached because of some differences in comparing with the old one.
>
> Please paste the full bootlog so we can see it.
>
> --
> Otavio Salvador O.S. Systems
> http://www.ossystems.com.br http://code.ossystems.com.br
> Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-28 13:36 ` Konstantin Kovalev
@ 2014-07-28 14:12 ` Daiane Angolini
2014-07-28 14:26 ` Konstantin Kovalev
0 siblings, 1 reply; 28+ messages in thread
From: Daiane Angolini @ 2014-07-28 14:12 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale, Otavio Salvador
On Mon, Jul 28, 2014 at 10:36 AM, Konstantin Kovalev
<lepeletie@hotmail.com> wrote:
> Dear Otavio,
> It was in attachment but OK:
>
> **************************************************************************************
> U-Boot 2014.07 (Jul 22 2014 - 00:23:28)
>
> CPU: Freescale i.MX6Q rev1.2 at 792 MHz
I tried the same pre-built image over here and after changing from:
mmcroot=/dev/mmcblk1p2
to
mmcroot=/dev/mmcblk0p2
I have it working fine.
Daiane
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-28 14:12 ` Daiane Angolini
@ 2014-07-28 14:26 ` Konstantin Kovalev
2014-07-28 15:37 ` Otavio Salvador
0 siblings, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-07-28 14:26 UTC (permalink / raw)
To: Daiane Angolini, meta-freescale
Dear Daiane,
I really glad to hear this. Perhaps you could add your boot log so that I could compare it with mine. I guess that it can help me somehow.
Thanks in advance.
Best Regards,
Konstantin.
----------------------------------------
> Date: Mon, 28 Jul 2014 11:12:14 -0300
> Subject: Re: [meta-freescale] Cannot boot after the last update...
> From: daiane.list@gmail.com
> To: lepeletie@hotmail.com
> CC: otavio@ossystems.com.br; meta-freescale@yoctoproject.org
>
> On Mon, Jul 28, 2014 at 10:36 AM, Konstantin Kovalev
> <lepeletie@hotmail.com> wrote:
>> Dear Otavio,
>> It was in attachment but OK:
>>
>> **************************************************************************************
>> U-Boot 2014.07 (Jul 22 2014 - 00:23:28)
>>
>> CPU: Freescale i.MX6Q rev1.2 at 792 MHz
>
>
> I tried the same pre-built image over here and after changing from:
>
> mmcroot=/dev/mmcblk1p2
>
> to
>
> mmcroot=/dev/mmcblk0p2
>
>
> I have it working fine.
>
> Daiane
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-28 14:26 ` Konstantin Kovalev
@ 2014-07-28 15:37 ` Otavio Salvador
2014-07-28 18:58 ` Daiane Angolini
0 siblings, 1 reply; 28+ messages in thread
From: Otavio Salvador @ 2014-07-28 15:37 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale
On Mon, Jul 28, 2014 at 11:26 AM, Konstantin Kovalev
<lepeletie@hotmail.com> wrote:
> I really glad to hear this. Perhaps you could add your boot log so that I could compare it with mine. I guess that it can help me somehow.
> Thanks in advance.
I sent an u-boot-fslc update which should address this issue. Can you
test master-next or apply it and test?
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-28 15:37 ` Otavio Salvador
@ 2014-07-28 18:58 ` Daiane Angolini
2014-07-30 12:41 ` Konstantin Kovalev
0 siblings, 1 reply; 28+ messages in thread
From: Daiane Angolini @ 2014-07-28 18:58 UTC (permalink / raw)
To: Otavio Salvador; +Cc: meta-freescale
On Mon, Jul 28, 2014 at 12:37 PM, Otavio Salvador
<otavio@ossystems.com.br> wrote:
> On Mon, Jul 28, 2014 at 11:26 AM, Konstantin Kovalev
> <lepeletie@hotmail.com> wrote:
>> I really glad to hear this. Perhaps you could add your boot log so that I could compare it with mine. I guess that it can help me somehow.
>> Thanks in advance.
>
> I sent an u-boot-fslc update which should address this issue. Can you
> test master-next or apply it and test?
I tested over here and it worked for me
Daiane
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-28 18:58 ` Daiane Angolini
@ 2014-07-30 12:41 ` Konstantin Kovalev
2014-07-30 17:26 ` Daiane Angolini
0 siblings, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-07-30 12:41 UTC (permalink / raw)
To: Daiane Angolini, otavio, meta-freescale
Today I have done "repo sync" and rebuilt my image but it stopped on "login:" again. So, my issue is still existing. Moreover, I faced this "mmcblk1p2" problem. It seems that I should rebuild my image completely (including kernel). So, how can I do this properly? ("-c cleanall -f" doesn't allow me to do that).
Best Regards,
Konstantin.
----------------------------------------
> Date: Mon, 28 Jul 2014 15:58:51 -0300
> Subject: Re: [meta-freescale] Cannot boot after the last update...
> From: daiane.list@gmail.com
> To: otavio@ossystems.com.br
> CC: lepeletie@hotmail.com; meta-freescale@yoctoproject.org
>
> On Mon, Jul 28, 2014 at 12:37 PM, Otavio Salvador
> <otavio@ossystems.com.br> wrote:
>> On Mon, Jul 28, 2014 at 11:26 AM, Konstantin Kovalev
>> <lepeletie@hotmail.com> wrote:
>>> I really glad to hear this. Perhaps you could add your boot log so that I could compare it with mine. I guess that it can help me somehow.
>>> Thanks in advance.
>>
>> I sent an u-boot-fslc update which should address this issue. Can you
>> test master-next or apply it and test?
>
> I tested over here and it worked for me
>
>
> Daiane
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-30 12:41 ` Konstantin Kovalev
@ 2014-07-30 17:26 ` Daiane Angolini
2014-07-30 18:05 ` Daiane Angolini
0 siblings, 1 reply; 28+ messages in thread
From: Daiane Angolini @ 2014-07-30 17:26 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale, otavio
On Wed, Jul 30, 2014 at 9:41 AM, Konstantin Kovalev
<lepeletie@hotmail.com> wrote:
> Today I have done "repo sync" and rebuilt my image but it stopped on "login:" again. So, my issue is still existing. Moreover, I faced this "mmcblk1p2" problem. It seems that I should rebuild my image completely (including kernel). So, how can I do this properly? ("-c cleanall -f" doesn't allow me to do that).
>
I did not understand your question. If you have "repo sync"-ed and the
fix is downloaded, YP will rebuild anything needed.
If you want to make sure twice, bitbake virtual/kernel -c cleansstate
and bitbake u-boot-fslc -c cleansstate
I still can *not* reproduce the issue. For me, it works, it reaches
the prompt I can login and I can find / until the end. And I still
have the board control.
I have tested with imx6Q TO1.1 and TO 1.2
Daiane
> Best Regards,
> Konstantin.
>
> ----------------------------------------
>> Date: Mon, 28 Jul 2014 15:58:51 -0300
>> Subject: Re: [meta-freescale] Cannot boot after the last update...
>> From: daiane.list@gmail.com
>> To: otavio@ossystems.com.br
>> CC: lepeletie@hotmail.com; meta-freescale@yoctoproject.org
>>
>> On Mon, Jul 28, 2014 at 12:37 PM, Otavio Salvador
>> <otavio@ossystems.com.br> wrote:
>>> On Mon, Jul 28, 2014 at 11:26 AM, Konstantin Kovalev
>>> <lepeletie@hotmail.com> wrote:
>>>> I really glad to hear this. Perhaps you could add your boot log so that I could compare it with mine. I guess that it can help me somehow.
>>>> Thanks in advance.
>>>
>>> I sent an u-boot-fslc update which should address this issue. Can you
>>> test master-next or apply it and test?
>>
>> I tested over here and it worked for me
>>
>>
>> Daiane
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-30 17:26 ` Daiane Angolini
@ 2014-07-30 18:05 ` Daiane Angolini
2014-07-30 19:47 ` Daiane Angolini
0 siblings, 1 reply; 28+ messages in thread
From: Daiane Angolini @ 2014-07-30 18:05 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale, otavio
On Wed, Jul 30, 2014 at 2:26 PM, Daiane Angolini <daiane.list@gmail.com> wrote:
> On Wed, Jul 30, 2014 at 9:41 AM, Konstantin Kovalev
> <lepeletie@hotmail.com> wrote:
>> Today I have done "repo sync" and rebuilt my image but it stopped on "login:" again. So, my issue is still existing. Moreover, I faced this "mmcblk1p2" problem. It seems that I should rebuild my image completely (including kernel). So, how can I do this properly? ("-c cleanall -f" doesn't allow me to do that).
>>
>
> I did not understand your question. If you have "repo sync"-ed and the
> fix is downloaded, YP will rebuild anything needed.
>
> If you want to make sure twice, bitbake virtual/kernel -c cleansstate
> and bitbake u-boot-fslc -c cleansstate
>
>
> I still can *not* reproduce the issue. For me, it works, it reaches
> the prompt I can login and I can find / until the end. And I still
> have the board control.
>
> I have tested with imx6Q TO1.1 and TO 1.2
And, I tested with imx6slevk as well, and it´s working.
Only reporting
Daiane
>
> Daiane
>
>
>> Best Regards,
>> Konstantin.
>>
>> ----------------------------------------
>>> Date: Mon, 28 Jul 2014 15:58:51 -0300
>>> Subject: Re: [meta-freescale] Cannot boot after the last update...
>>> From: daiane.list@gmail.com
>>> To: otavio@ossystems.com.br
>>> CC: lepeletie@hotmail.com; meta-freescale@yoctoproject.org
>>>
>>> On Mon, Jul 28, 2014 at 12:37 PM, Otavio Salvador
>>> <otavio@ossystems.com.br> wrote:
>>>> On Mon, Jul 28, 2014 at 11:26 AM, Konstantin Kovalev
>>>> <lepeletie@hotmail.com> wrote:
>>>>> I really glad to hear this. Perhaps you could add your boot log so that I could compare it with mine. I guess that it can help me somehow.
>>>>> Thanks in advance.
>>>>
>>>> I sent an u-boot-fslc update which should address this issue. Can you
>>>> test master-next or apply it and test?
>>>
>>> I tested over here and it worked for me
>>>
>>>
>>> Daiane
>>
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-30 18:05 ` Daiane Angolini
@ 2014-07-30 19:47 ` Daiane Angolini
2014-07-30 20:19 ` Fabio Estevam
2014-07-31 7:35 ` Konstantin Kovalev
0 siblings, 2 replies; 28+ messages in thread
From: Daiane Angolini @ 2014-07-30 19:47 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale, otavio
On Wed, Jul 30, 2014 at 3:05 PM, Daiane Angolini <daiane.list@gmail.com> wrote:
> On Wed, Jul 30, 2014 at 2:26 PM, Daiane Angolini <daiane.list@gmail.com> wrote:
>> On Wed, Jul 30, 2014 at 9:41 AM, Konstantin Kovalev
>> <lepeletie@hotmail.com> wrote:
>>> Today I have done "repo sync" and rebuilt my image but it stopped on "login:" again. So, my issue is still existing. Moreover, I faced this "mmcblk1p2" problem. It seems that I should rebuild my image completely (including kernel). So, how can I do this properly? ("-c cleanall -f" doesn't allow me to do that).
>>>
>>
>> I did not understand your question. If you have "repo sync"-ed and the
>> fix is downloaded, YP will rebuild anything needed.
>>
>> If you want to make sure twice, bitbake virtual/kernel -c cleansstate
>> and bitbake u-boot-fslc -c cleansstate
>>
>>
>> I still can *not* reproduce the issue. For me, it works, it reaches
>> the prompt I can login and I can find / until the end. And I still
>> have the board control.
>>
>> I have tested with imx6Q TO1.1 and TO 1.2
>
> And, I tested with imx6slevk as well, and it´s working.
I reproduced the freeze issue using imx6qsabresd and X11!
So, it´s x11 startup error.
Daiane
>
>
> Only reporting
>
> Daiane
>>
>> Daiane
>>
>>
>>> Best Regards,
>>> Konstantin.
>>>
>>> ----------------------------------------
>>>> Date: Mon, 28 Jul 2014 15:58:51 -0300
>>>> Subject: Re: [meta-freescale] Cannot boot after the last update...
>>>> From: daiane.list@gmail.com
>>>> To: otavio@ossystems.com.br
>>>> CC: lepeletie@hotmail.com; meta-freescale@yoctoproject.org
>>>>
>>>> On Mon, Jul 28, 2014 at 12:37 PM, Otavio Salvador
>>>> <otavio@ossystems.com.br> wrote:
>>>>> On Mon, Jul 28, 2014 at 11:26 AM, Konstantin Kovalev
>>>>> <lepeletie@hotmail.com> wrote:
>>>>>> I really glad to hear this. Perhaps you could add your boot log so that I could compare it with mine. I guess that it can help me somehow.
>>>>>> Thanks in advance.
>>>>>
>>>>> I sent an u-boot-fslc update which should address this issue. Can you
>>>>> test master-next or apply it and test?
>>>>
>>>> I tested over here and it worked for me
>>>>
>>>>
>>>> Daiane
>>>
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-30 19:47 ` Daiane Angolini
@ 2014-07-30 20:19 ` Fabio Estevam
2014-07-31 7:35 ` Konstantin Kovalev
1 sibling, 0 replies; 28+ messages in thread
From: Fabio Estevam @ 2014-07-30 20:19 UTC (permalink / raw)
To: Daiane Angolini; +Cc: meta-freescale, otavio
On Wed, Jul 30, 2014 at 4:47 PM, Daiane Angolini <daiane.list@gmail.com> wrote:
> I reproduced the freeze issue using imx6qsabresd and X11!
>
> So, it´s x11 startup error.
Do you see the freeze if you use 'imx6q-sabresd-ldo,dtb' instead?
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-30 19:47 ` Daiane Angolini
2014-07-30 20:19 ` Fabio Estevam
@ 2014-07-31 7:35 ` Konstantin Kovalev
2014-07-31 12:19 ` Otavio Salvador
1 sibling, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-07-31 7:35 UTC (permalink / raw)
To: Daiane Angolini, meta-freescale
Dear Daiane,
It is a good news that I am not alone with this issue! As I mentioned in my first message I use "fsl-image-multimedia-full". Moreover, the X11 is really needed for "linphone+Xvideo". So, I can not do without it. What is worse is that my board doesn't show me any errors in X11 it just freezes. So, now, thanks to your message, I understand the causes of the freeze and I can continue trying to find a solution. Thank you for that again.
Best Regards,
Konstantin.
----------------------------------------
> Date: Wed, 30 Jul 2014 16:47:59 -0300
> Subject: Re: [meta-freescale] Cannot boot after the last update...
> From: daiane.list@gmail.com
> To: lepeletie@hotmail.com
> CC: otavio@ossystems.com.br; meta-freescale@yoctoproject.org
>
> On Wed, Jul 30, 2014 at 3:05 PM, Daiane Angolini <daiane.list@gmail.com> wrote:
>> On Wed, Jul 30, 2014 at 2:26 PM, Daiane Angolini <daiane.list@gmail.com> wrote:
>>> On Wed, Jul 30, 2014 at 9:41 AM, Konstantin Kovalev
>>> <lepeletie@hotmail.com> wrote:
>>>> Today I have done "repo sync" and rebuilt my image but it stopped on "login:" again. So, my issue is still existing. Moreover, I faced this "mmcblk1p2" problem. It seems that I should rebuild my image completely (including kernel). So, how can I do this properly? ("-c cleanall -f" doesn't allow me to do that).
>>>>
>>>
>>> I did not understand your question. If you have "repo sync"-ed and the
>>> fix is downloaded, YP will rebuild anything needed.
>>>
>>> If you want to make sure twice, bitbake virtual/kernel -c cleansstate
>>> and bitbake u-boot-fslc -c cleansstate
>>>
>>>
>>> I still can *not* reproduce the issue. For me, it works, it reaches
>>> the prompt I can login and I can find / until the end. And I still
>>> have the board control.
>>>
>>> I have tested with imx6Q TO1.1 and TO 1.2
>>
>> And, I tested with imx6slevk as well, and it´s working.
>
> I reproduced the freeze issue using imx6qsabresd and X11!
>
> So, it´s x11 startup error.
>
>
>
> Daiane
>>
>>
>> Only reporting
>>
>> Daiane
>>>
>>> Daiane
>>>
>>>
>>>> Best Regards,
>>>> Konstantin.
>>>>
>>>> ----------------------------------------
>>>>> Date: Mon, 28 Jul 2014 15:58:51 -0300
>>>>> Subject: Re: [meta-freescale] Cannot boot after the last update...
>>>>> From: daiane.list@gmail.com
>>>>> To: otavio@ossystems.com.br
>>>>> CC: lepeletie@hotmail.com; meta-freescale@yoctoproject.org
>>>>>
>>>>> On Mon, Jul 28, 2014 at 12:37 PM, Otavio Salvador
>>>>> <otavio@ossystems.com.br> wrote:
>>>>>> On Mon, Jul 28, 2014 at 11:26 AM, Konstantin Kovalev
>>>>>> <lepeletie@hotmail.com> wrote:
>>>>>>> I really glad to hear this. Perhaps you could add your boot log so that I could compare it with mine. I guess that it can help me somehow.
>>>>>>> Thanks in advance.
>>>>>>
>>>>>> I sent an u-boot-fslc update which should address this issue. Can you
>>>>>> test master-next or apply it and test?
>>>>>
>>>>> I tested over here and it worked for me
>>>>>
>>>>>
>>>>> Daiane
>>>>
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-31 7:35 ` Konstantin Kovalev
@ 2014-07-31 12:19 ` Otavio Salvador
2014-07-31 12:43 ` Daiane Angolini
0 siblings, 1 reply; 28+ messages in thread
From: Otavio Salvador @ 2014-07-31 12:19 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale
On Thu, Jul 31, 2014 at 4:35 AM, Konstantin Kovalev
<lepeletie@hotmail.com> wrote:
> It is a good news that I am not alone with this issue! As I mentioned in my first message I use "fsl-image-multimedia-full". Moreover, the X11 is really needed for "linphone+Xvideo". So, I can not do without it. What is worse is that my board doesn't show me any errors in X11 it just freezes. So, now, thanks to your message, I understand the causes of the freeze and I can continue trying to find a solution. Thank you for that again.
Please see Fabio's message and test with the ldo.dtb; so we see if it helps...
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-31 12:19 ` Otavio Salvador
@ 2014-07-31 12:43 ` Daiane Angolini
2014-08-01 6:23 ` Konstantin Kovalev
0 siblings, 1 reply; 28+ messages in thread
From: Daiane Angolini @ 2014-07-31 12:43 UTC (permalink / raw)
To: Otavio Salvador; +Cc: meta-freescale
On Thu, Jul 31, 2014 at 9:19 AM, Otavio Salvador
<otavio@ossystems.com.br> wrote:
> On Thu, Jul 31, 2014 at 4:35 AM, Konstantin Kovalev
> <lepeletie@hotmail.com> wrote:
>> It is a good news that I am not alone with this issue! As I mentioned in my first message I use "fsl-image-multimedia-full". Moreover, the X11 is really needed for "linphone+Xvideo". So, I can not do without it. What is worse is that my board doesn't show me any errors in X11 it just freezes. So, now, thanks to your message, I understand the causes of the freeze and I can continue trying to find a solution. Thank you for that again.
>
> Please see Fabio's message and test with the ldo.dtb; so we see if it helps...
I just tested -ldo and it worked.
Daiane
>
> --
> Otavio Salvador O.S. Systems
> http://www.ossystems.com.br http://code.ossystems.com.br
> Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-07-31 12:43 ` Daiane Angolini
@ 2014-08-01 6:23 ` Konstantin Kovalev
2014-08-01 12:36 ` Otavio Salvador
0 siblings, 1 reply; 28+ messages in thread
From: Konstantin Kovalev @ 2014-08-01 6:23 UTC (permalink / raw)
To: Daiane Angolini, meta-freescale, otavio
Yes, I can confirm that it works. The solution is just change "fdt_file=imx6q-sabresd.dtb" to "fdt_file=imx6q-sabresd-ldo.dtb". Thanks to all!
Best Regards,
Konstantin.
----------------------------------------
> Date: Thu, 31 Jul 2014 09:43:43 -0300
> Subject: Re: [meta-freescale] Cannot boot after the last update...
> From: daiane.list@gmail.com
> To: otavio@ossystems.com.br
> CC: lepeletie@hotmail.com; meta-freescale@yoctoproject.org
>
> On Thu, Jul 31, 2014 at 9:19 AM, Otavio Salvador
> <otavio@ossystems.com.br> wrote:
>> On Thu, Jul 31, 2014 at 4:35 AM, Konstantin Kovalev
>> <lepeletie@hotmail.com> wrote:
>>> It is a good news that I am not alone with this issue! As I mentioned in my first message I use "fsl-image-multimedia-full". Moreover, the X11 is really needed for "linphone+Xvideo". So, I can not do without it. What is worse is that my board doesn't show me any errors in X11 it just freezes. So, now, thanks to your message, I understand the causes of the freeze and I can continue trying to find a solution. Thank you for that again.
>>
>> Please see Fabio's message and test with the ldo.dtb; so we see if it helps...
>
> I just tested -ldo and it worked.
>
> Daiane
>>
>> --
>> Otavio Salvador O.S. Systems
>> http://www.ossystems.com.br http://code.ossystems.com.br
>> Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-08-01 6:23 ` Konstantin Kovalev
@ 2014-08-01 12:36 ` Otavio Salvador
2014-08-01 17:35 ` Fabio Estevam
0 siblings, 1 reply; 28+ messages in thread
From: Otavio Salvador @ 2014-08-01 12:36 UTC (permalink / raw)
To: Konstantin Kovalev; +Cc: meta-freescale
On Fri, Aug 1, 2014 at 3:23 AM, Konstantin Kovalev
<lepeletie@hotmail.com> wrote:
> Yes, I can confirm that it works. The solution is just change "fdt_file=imx6q-sabresd.dtb" to "fdt_file=imx6q-sabresd-ldo.dtb". Thanks to all!
Not really a solution but a workaround.
The U-Boot 2014.07 provides the PMIC driving support so this shouldn't
be need. Fabio, any tip on this?
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-08-01 12:36 ` Otavio Salvador
@ 2014-08-01 17:35 ` Fabio Estevam
2014-08-01 17:37 ` Otavio Salvador
0 siblings, 1 reply; 28+ messages in thread
From: Fabio Estevam @ 2014-08-01 17:35 UTC (permalink / raw)
To: Otavio Salvador; +Cc: meta-freescale
On Fri, Aug 1, 2014 at 9:36 AM, Otavio Salvador <otavio@ossystems.com.br> wrote:
> The U-Boot 2014.07 provides the PMIC driving support so this shouldn't
> be need. Fabio, any tip on this?
Yes, it does have PMIC support, but it still lacks ldo bypass support.
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-08-01 17:35 ` Fabio Estevam
@ 2014-08-01 17:37 ` Otavio Salvador
2014-08-01 17:39 ` Fabio Estevam
0 siblings, 1 reply; 28+ messages in thread
From: Otavio Salvador @ 2014-08-01 17:37 UTC (permalink / raw)
To: Fabio Estevam; +Cc: meta-freescale
On Fri, Aug 1, 2014 at 2:35 PM, Fabio Estevam <festevam@gmail.com> wrote:
> On Fri, Aug 1, 2014 at 9:36 AM, Otavio Salvador <otavio@ossystems.com.br> wrote:
>
>> The U-Boot 2014.07 provides the PMIC driving support so this shouldn't
>> be need. Fabio, any tip on this?
>
> Yes, it does have PMIC support, but it still lacks ldo bypass support.
So we ought to keep using -ldo for now?
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-08-01 17:37 ` Otavio Salvador
@ 2014-08-01 17:39 ` Fabio Estevam
2014-08-01 17:47 ` Otavio Salvador
0 siblings, 1 reply; 28+ messages in thread
From: Fabio Estevam @ 2014-08-01 17:39 UTC (permalink / raw)
To: Otavio Salvador; +Cc: meta-freescale
On Fri, Aug 1, 2014 at 2:37 PM, Otavio Salvador <otavio@ossystems.com.br> wrote:
> On Fri, Aug 1, 2014 at 2:35 PM, Fabio Estevam <festevam@gmail.com> wrote:
>> On Fri, Aug 1, 2014 at 9:36 AM, Otavio Salvador <otavio@ossystems.com.br> wrote:
>>
>>> The U-Boot 2014.07 provides the PMIC driving support so this shouldn't
>>> be need. Fabio, any tip on this?
>>
>> Yes, it does have PMIC support, but it still lacks ldo bypass support.
>
> So we ought to keep using -ldo for now?
That's correct.
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Cannot boot after the last update...
2014-08-01 17:39 ` Fabio Estevam
@ 2014-08-01 17:47 ` Otavio Salvador
0 siblings, 0 replies; 28+ messages in thread
From: Otavio Salvador @ 2014-08-01 17:47 UTC (permalink / raw)
To: Fabio Estevam; +Cc: meta-freescale
On Fri, Aug 1, 2014 at 2:39 PM, Fabio Estevam <festevam@gmail.com> wrote:
> On Fri, Aug 1, 2014 at 2:37 PM, Otavio Salvador <otavio@ossystems.com.br> wrote:
>> On Fri, Aug 1, 2014 at 2:35 PM, Fabio Estevam <festevam@gmail.com> wrote:
>>> On Fri, Aug 1, 2014 at 9:36 AM, Otavio Salvador <otavio@ossystems.com.br> wrote:
>>>
>>>> The U-Boot 2014.07 provides the PMIC driving support so this shouldn't
>>>> be need. Fabio, any tip on this?
>>>
>>> Yes, it does have PMIC support, but it still lacks ldo bypass support.
>>
>> So we ought to keep using -ldo for now?
>
> That's correct.
I forward-ported the corresponding patch from 2014.01 to 2014.07 and
updated master.
It should be fine now.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 28+ messages in thread
end of thread, other threads:[~2014-08-01 17:47 UTC | newest]
Thread overview: 28+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-07-23 8:16 Cannot boot after the last update Konstantin Kovalev
2014-07-25 5:21 ` Otavio Salvador
2014-07-25 12:12 ` Konstantin Kovalev
2014-07-25 12:16 ` Otavio Salvador
2014-07-25 12:19 ` Konstantin Kovalev
2014-07-25 12:32 ` Otavio Salvador
2014-07-28 6:11 ` Konstantin Kovalev
2014-07-28 8:10 ` Konstantin Kovalev
2014-07-28 13:28 ` Otavio Salvador
2014-07-28 13:36 ` Konstantin Kovalev
2014-07-28 14:12 ` Daiane Angolini
2014-07-28 14:26 ` Konstantin Kovalev
2014-07-28 15:37 ` Otavio Salvador
2014-07-28 18:58 ` Daiane Angolini
2014-07-30 12:41 ` Konstantin Kovalev
2014-07-30 17:26 ` Daiane Angolini
2014-07-30 18:05 ` Daiane Angolini
2014-07-30 19:47 ` Daiane Angolini
2014-07-30 20:19 ` Fabio Estevam
2014-07-31 7:35 ` Konstantin Kovalev
2014-07-31 12:19 ` Otavio Salvador
2014-07-31 12:43 ` Daiane Angolini
2014-08-01 6:23 ` Konstantin Kovalev
2014-08-01 12:36 ` Otavio Salvador
2014-08-01 17:35 ` Fabio Estevam
2014-08-01 17:37 ` Otavio Salvador
2014-08-01 17:39 ` Fabio Estevam
2014-08-01 17:47 ` Otavio Salvador
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.