[PATCH net-next] net: mtk_eth_soc: use resolved link config in mac_link_up()

[PATCH net-next] net: mtk_eth_soc: use resolved link config in mac_link_up()

[Russell King]

Convert the mtk_eth_soc driver to use the finalised link parameters in
mac_link_up() rather than the parameters in mac_config().

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
This is my untested stab at converting mtk_eth_soc.c to use the state
passed in via mac_link_up() rather than mac_config(). Please test and
report back. Thanks.

 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 45 ++++++++++++---------
 1 file changed, 25 insertions(+), 20 deletions(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index f6a1f8666f95..20db302d31ce 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -344,29 +344,9 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 	/* Setup gmac */
 	mcr_cur = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
 	mcr_new = mcr_cur;
-	mcr_new &= ~(MAC_MCR_SPEED_100 | MAC_MCR_SPEED_1000 |
-		     MAC_MCR_FORCE_DPX | MAC_MCR_FORCE_TX_FC |
-		     MAC_MCR_FORCE_RX_FC);
 	mcr_new |= MAC_MCR_MAX_RX_1536 | MAC_MCR_IPG_CFG | MAC_MCR_FORCE_MODE |
 		   MAC_MCR_BACKOFF_EN | MAC_MCR_BACKPR_EN | MAC_MCR_FORCE_LINK;
 
-	switch (state->speed) {
-	case SPEED_2500:
-	case SPEED_1000:
-		mcr_new |= MAC_MCR_SPEED_1000;
-		break;
-	case SPEED_100:
-		mcr_new |= MAC_MCR_SPEED_100;
-		break;
-	}
-	if (state->duplex == DUPLEX_FULL) {
-		mcr_new |= MAC_MCR_FORCE_DPX;
-		if (state->pause & MLO_PAUSE_TX)
-			mcr_new |= MAC_MCR_FORCE_TX_FC;
-		if (state->pause & MLO_PAUSE_RX)
-			mcr_new |= MAC_MCR_FORCE_RX_FC;
-	}
-
 	/* Only update control register when needed! */
 	if (mcr_new != mcr_cur)
 		mtk_w32(mac->hw, mcr_new, MTK_MAC_MCR(mac->id));
@@ -443,6 +423,31 @@ static void mtk_mac_link_up(struct phylink_config *config,
 					   phylink_config);
 	u32 mcr = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
 
+	mcr &= ~(MAC_MCR_SPEED_100 | MAC_MCR_SPEED_1000 |
+		 MAC_MCR_FORCE_DPX | MAC_MCR_FORCE_TX_FC |
+		 MAC_MCR_FORCE_RX_FC);
+
+	/* Configure speed */
+	switch (speed) {
+	case SPEED_2500:
+	case SPEED_1000:
+		mcr |= MAC_MCR_SPEED_1000;
+		break;
+	case SPEED_100:
+		mcr |= MAC_MCR_SPEED_100;
+		break;
+	}
+
+	/* Configure duplex */
+	if (duplex == DUPLEX_FULL)
+		mcr |= MAC_MCR_FORCE_DPX;
+
+	/* Configure pause modes - phylink will avoid these for half duplex */
+	if (tx_pause)
+		mcr |= MAC_MCR_FORCE_TX_FC;
+	if (rx_pause)
+		mcr |= MAC_MCR_FORCE_RX_FC;
+
 	mcr |= MAC_MCR_TX_EN | MAC_MCR_RX_EN;
 	mtk_w32(mac->hw, mcr, MTK_MAC_MCR(mac->id));
 }
-- 
2.20.1

Re: [PATCH net-next] net: mtk_eth_soc: use resolved link config in mac_link_up()

[David Miller]

From: Russell King <rmk+kernel@armlinux.org.uk>
Date: Sun, 21 Jun 2020 15:36:39 +0100

> Convert the mtk_eth_soc driver to use the finalised link parameters in
> mac_link_up() rather than the parameters in mac_config().
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Applied.