From: vishwanatha subbanna <vishwa@linux.vnet.ibm.com>
To: devicetree@vger.kernel.org, eajames@linux.ibm.com,
joel@jms.id.au, openbmc@lists.ozlabs.org
Cc: vishwanatha subbanna <vishwa@linux.vnet.ibm.com>
Subject: [PATCH 2/2] rainier: Add LEDs that are controlled by ASPEED
Date: Mon, 27 Jul 2020 18:10:51 +0530 [thread overview]
Message-ID: <FCA5474B-8A73-4D2B-9EF7-8B2E49DDFDD2@linux.vnet.ibm.com> (raw)
These are the LEDs that have direct GPIO connection from ASPEED
Signed-off-by: Vishwanatha Subbanna <vishwa@linux.vnet.ibm.com>
---
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 24 ++++++++++++++++++++++--
1 file changed, 22 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
index ecbce50..dc68c49 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
@@ -72,6 +72,26 @@
leds {
compatible = "gpio-leds";
+ /* BMC Card fault LED at the back */
+ bmc-ingraham0 {
+ gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+ };
+
+ /* Enclosure ID LED at the back */
+ rear-enc-id0 {
+ gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+ };
+
+ /* Enclosure fault LED at the back */
+ rear-enc-fault0 {
+ gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+ };
+
+ /* PCIE slot power LED */
+ pcieslot-power {
+ gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+ };
+
/* System ID LED that is at front on Op Panel */
front-sys-id0 {
retain-state-shutdown;
@@ -112,7 +132,7 @@
/*E0-E7*/ "","","","","","","","",
/*F0-F7*/ "","","","","","","","",
/*G0-G7*/ "","","","","","","","",
- /*H0-H7*/ "","","","","","","","",
+ /*H0-H7*/ "","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
/*I0-I7*/ "","","","","","","","",
/*J0-J7*/ "","","","","","","","",
/*K0-K7*/ "","","","","","","","",
@@ -120,7 +140,7 @@
/*M0-M7*/ "","","","","","","","",
/*N0-N7*/ "","","","","","","","",
/*O0-O7*/ "","","","","","","","",
- /*P0-P7*/ "","","","","","","","",
+ /*P0-P7*/ "","","","","pcieslot-power","","","",
/*Q0-Q7*/ "cfam-reset","","","","","","","",
/*R0-R7*/ "","","","","","","","",
/*S0-S7*/ "presence-ps0","presence-ps1","presence-ps2","presence-ps3",
--
1.8.3.1
WARNING: multiple messages have this Message-ID (diff)
From: vishwanatha subbanna <vishwa@linux.vnet.ibm.com>
To: devicetree@vger.kernel.org, eajames@linux.ibm.com,
joel@jms.id.au, openbmc@lists.ozlabs.org
Subject: [PATCH 2/2] rainier: Add LEDs that are controlled by ASPEED
Date: Mon, 27 Jul 2020 18:10:51 +0530 [thread overview]
Message-ID: <FCA5474B-8A73-4D2B-9EF7-8B2E49DDFDD2@linux.vnet.ibm.com> (raw)
These are the LEDs that have direct GPIO connection from ASPEED
Signed-off-by: Vishwanatha Subbanna <vishwa@linux.vnet.ibm.com>
---
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 24 ++++++++++++++++++++++--
1 file changed, 22 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
index ecbce50..dc68c49 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
@@ -72,6 +72,26 @@
leds {
compatible = "gpio-leds";
+ /* BMC Card fault LED at the back */
+ bmc-ingraham0 {
+ gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+ };
+
+ /* Enclosure ID LED at the back */
+ rear-enc-id0 {
+ gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+ };
+
+ /* Enclosure fault LED at the back */
+ rear-enc-fault0 {
+ gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+ };
+
+ /* PCIE slot power LED */
+ pcieslot-power {
+ gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+ };
+
/* System ID LED that is at front on Op Panel */
front-sys-id0 {
retain-state-shutdown;
@@ -112,7 +132,7 @@
/*E0-E7*/ "","","","","","","","",
/*F0-F7*/ "","","","","","","","",
/*G0-G7*/ "","","","","","","","",
- /*H0-H7*/ "","","","","","","","",
+ /*H0-H7*/ "","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
/*I0-I7*/ "","","","","","","","",
/*J0-J7*/ "","","","","","","","",
/*K0-K7*/ "","","","","","","","",
@@ -120,7 +140,7 @@
/*M0-M7*/ "","","","","","","","",
/*N0-N7*/ "","","","","","","","",
/*O0-O7*/ "","","","","","","","",
- /*P0-P7*/ "","","","","","","","",
+ /*P0-P7*/ "","","","","pcieslot-power","","","",
/*Q0-Q7*/ "cfam-reset","","","","","","","",
/*R0-R7*/ "","","","","","","","",
/*S0-S7*/ "presence-ps0","presence-ps1","presence-ps2","presence-ps3",
--
1.8.3.1
next reply other threads:[~2020-07-27 12:41 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-27 12:40 vishwanatha subbanna [this message]
2020-07-27 12:40 ` [PATCH 2/2] rainier: Add LEDs that are controlled by ASPEED vishwanatha subbanna
2020-07-27 21:20 ` Eddie James
-- strict thread matches above, loose matches on Subject: below --
2020-07-28 13:59 Vishwanatha Subbanna
2020-07-28 20:45 ` Eddie James
2020-07-09 11:14 Vishwanatha Subbanna
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=FCA5474B-8A73-4D2B-9EF7-8B2E49DDFDD2@linux.vnet.ibm.com \
--to=vishwa@linux.vnet.ibm.com \
--cc=devicetree@vger.kernel.org \
--cc=eajames@linux.ibm.com \
--cc=joel@jms.id.au \
--cc=openbmc@lists.ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.