* [ath10k USB QCA9377] Driver fails to initialize Linksys device
[not found] <MW2PR12MB2458671FF0444136A06CE26BF8000@MW2PR12MB2458.namprd12.prod.outlook.com>
@ 2018-09-07 7:39 ` Vincent Guenat
0 siblings, 0 replies; only message in thread
From: Vincent Guenat @ 2018-09-07 7:39 UTC (permalink / raw)
To: ath10k
[-- Attachment #1: Type: text/plain, Size: 3446 bytes --]
Good morning,
I am trying to set up the Linksys WUSB6100M USB wireless adapter and have encountered problem after the first initialization, as the device is disconnected from the USB bus about 1 second after finishing the init (cf. dmesg output).
Disclaimer: I am aware and accept that the USB support, as stated in https://marc.info/?l=linux-wireless&m=149934315517807&w=2 and in the warning message from the driver, is incomplete and might simply not work for my use case (monitor mode for DFS events, no emission, no connection/authentication to any AP). With that said, I think it might work as this is the same device as the one used by Eric Stromdahl when he tested his USB support (cf. https://marc.info/?l=linux-wireless&m=148434332728333&w=2).
Here are more information on the setup:
Device: Linksys WUSB6100M with QCA9377 chipset.
OS: Debian 9 (stretch) as a VirtualBox guest on a Windows 10 host.
Arch: x86_64.
VirtualBox guest additions: installed.
VirtualBox extension pack (xHCI/EHCI support): installed.
Kernel version: 4.14.67, compiled with ath10k support:
CONFIG_ATH10K=m
CONFIG_ATH10K_PCI=m
CONFIG_ATH10K_SDIO=m
CONFIG_ATH10K_USB=m
CONFIG_ATH10K_DEBUG=y
CONFIG_ATH10K_DEBUGFS=y
CONFIG_ATH10K_TRACING=y
$uname -a
Linux debian 4.14.67 #1 SMP Wed Sep 5 12:27:57 CEST 2018 x86_64 GNU/Linux
$cat /etc/modprobe.d/local.conf
options ath10k_core debug_mask=0xffffffff
Attached files:
- dmesg-full.txt: full output of dmesg, in case the problem might come from outside ath10k.
- dmesg-usb-1-2.txt: the same output, but filtered to keep only the messages relative to the device.
Firmware: firmware-5.bin_CNSS.TF.1.0-00267-QCATFSWPZ-1 from https://github.com/kvalo/ath10k-firmware repo on github (in ath10k-firmware/QCA9377/hw1.0/CNSS.TF.1.0/, master branch).
Firmware name in /lib/firmware/ath10k/QCA9377/hw1.0/: firmware-usb-5.bin
Board file: eeprom_qca9377_7_1p1_Robin_clpc_ce.bin, symlink in /lib/firmware/ath10k/QCA9377/hw1.0/ as both board-usb.bin and board.bin
The board file was added to the board-2.bin file using the ath10k-bdencoder from the https://github.com/qca/qca-swiss-army-knife/ github repository (as ath10k indicated it could not initially find the board file in board-2.bin). The exact commands used were:
$ f=/lib/firmware/ath10k/QCA9377/hw1.0/
$ sudo ath10k-bdencoder --add-board $f/board-2.bin $f/eeprom_qca9377_7_1p1_Robin_clpc_ce.bin “bus=13b1,device=0042,subsystem-vendor=0000,subsystem-device=0000”
As an additional note, the “usb 1-2: zero length frame received, firmware crashed?” message near the end of the dmesg output seems to suggest a firmware problem, but it does not always appear when plugging in the device (only about 1 out of 3 times).
My assumption is that there is a problem with the firmware, i.e. I did something wrong with it but I don’t know what. Can you help me?
Best regards,
Vincent Guenat.
TriaGnoSys GmbH, Registergericht: München HRB 141647, Vat.: DE 813396184 Geschäftsführer: Núria Riera Díaz, Peter Lewalter
________________________________
This email and any files transmitted with it are confidential & proprietary to Zodiac Inflight Innovations. This information is intended solely for the use of the individual or entity to which it is addressed. Access or transmittal of the information contained in this e-mail, in full or in part, to any other organization or persons is not authorized.
[-- Attachment #2: dmesg-full.txt --]
[-- Type: text/plain, Size: 78066 bytes --]
[ 0.000000] Linux version 4.14.67 (vguenat@debian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP Wed Sep 5 12:27:57 CEST 2018
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-4.14.67 root=/dev/mapper/debian--vg-root ro quiet
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000dffeffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dfff0000-0x00000000dfffffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011fffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.5 present.
[ 0.000000] DMI: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 0.000000] Hypervisor detected: KVM
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x120000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR variable ranges disabled:
[ 0.000000] MTRR: Disabled
[ 0.000000] x86/PAT: MTRRs disabled, skipping PAT initialization too.
[ 0.000000] CPU MTRRs all blank - virtualized system.
[ 0.000000] x86/PAT: Configuration [0-7]: WB WT UC- UC WB WT UC- UC
[ 0.000000] e820: last_pfn = 0xdfff0 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x0009fff0-0x0009ffff] mapped at [ffffffffff200ff0]
[ 0.000000] Base memory trampoline at [ffff99e6c0099000] 99000 size 24576
[ 0.000000] BRK [0x88206000, 0x88206fff] PGTABLE
[ 0.000000] BRK [0x88207000, 0x88207fff] PGTABLE
[ 0.000000] BRK [0x88208000, 0x88208fff] PGTABLE
[ 0.000000] BRK [0x88209000, 0x88209fff] PGTABLE
[ 0.000000] BRK [0x8820a000, 0x8820afff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x355dd000-0x36ae5fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000E0000 000024 (v02 VBOX )
[ 0.000000] ACPI: XSDT 0x00000000DFFF0030 00003C (v01 VBOX VBOXXSDT 00000001 ASL 00000061)
[ 0.000000] ACPI: FACP 0x00000000DFFF00F0 0000F4 (v04 VBOX VBOXFACP 00000001 ASL 00000061)
[ 0.000000] ACPI: DSDT 0x00000000DFFF0470 0021FF (v02 VBOX VBOXBIOS 00000002 INTL 20100528)
[ 0.000000] ACPI: FACS 0x00000000DFFF0200 000040
[ 0.000000] ACPI: FACS 0x00000000DFFF0200 000040
[ 0.000000] ACPI: APIC 0x00000000DFFF0240 00005C (v02 VBOX VBOXAPIC 00000001 ASL 00000061)
[ 0.000000] ACPI: SSDT 0x00000000DFFF02A0 0001CC (v01 VBOX VBOXCPUT 00000002 INTL 20100528)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000011fffffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x11fff7000-0x11fffbfff]
[ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00
[ 0.000000] kvm-clock: cpu 0, msr 1:1ffef001, primary cpu clock
[ 0.000000] kvm-clock: using sched offset of 9083974782 cycles
[ 0.000000] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000011fffffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x00000000dffeffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000011fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000011fffffff]
[ 0.000000] On node 0 totalpages: 1048462
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14272 pages used for memmap
[ 0.000000] DMA32 zone: 913392 pages, LIFO batch:31
[ 0.000000] Normal zone: 2048 pages used for memmap
[ 0.000000] Normal zone: 131072 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdfff0000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfffbffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfffc0000-0xffffffff]
[ 0.000000] e820: [mem 0xe0000000-0xfebfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on KVM
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x478 with crng_init=0
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] percpu: Embedded 44 pages/cpu @ffff99e7dfc00000 s142424 r8192 d29608 u1048576
[ 0.000000] pcpu-alloc: s142424 r8192 d29608 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032057
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-4.14.67 root=/dev/mapper/debian--vg-root ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 4017604K/4193848K available (10252K kernel code, 1141K rwdata, 3004K rodata, 1524K init, 664K bss, 176244K reserved, 0K cma-reserved)
[ 0.000000] Kernel/User page tables isolation: enabled
[ 0.000000] ftrace: allocating 29022 entries in 114 pages
[ 0.004000] Hierarchical RCU implementation.
[ 0.004000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2.
[ 0.004000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.004000] NR_IRQS: 33024, nr_irqs: 440, preallocated irqs: 16
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] tsc: Detected 2712.000 MHz processor
[ 0.004000] Calibrating delay loop (skipped) preset value.. 5424.00 BogoMIPS (lpj=10848000)
[ 0.004000] pid_max: default: 32768 minimum: 301
[ 0.004000] ACPI: Core revision 20170728
[ 0.004000] ACPI: 2 ACPI AML tables successfully acquired and loaded
[ 0.004000] Security Framework initialized
[ 0.004000] Yama: becoming mindful.
[ 0.004000] AppArmor: AppArmor disabled by boot time parameter
[ 0.004000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.004128] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.004153] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.004159] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.004360] mce: CPU supports 0 MCE banks
[ 0.004378] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8
[ 0.004379] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[ 0.004380] Spectre V2 : Mitigation: Full generic retpoline
[ 0.004380] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.004381] Speculative Store Bypass: Vulnerable
[ 0.004448] Freeing SMP alternatives memory: 28K
[ 0.008118] smpboot: Max logical packages: 1
[ 0.008384] x2apic enabled
[ 0.008631] Switched APIC routing to physical x2apic.
[ 0.009928] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.016000] smpboot: CPU0: Intel(R) Core(TM) i5-7300U CPU @ 2.60GHz (family: 0x6, model: 0x8e, stepping: 0x9)
[ 0.016000] Performance Events: unsupported p6 CPU model 142 no PMU driver, software events only.
[ 0.016000] Hierarchical SRCU implementation.
[ 0.016000] NMI watchdog: Perf event create on CPU 0 failed with -2
[ 0.016000] NMI watchdog: Perf NMI watchdog permanently disabled
[ 0.016000] smp: Bringing up secondary CPUs ...
[ 0.016000] x86: Booting SMP configuration:
[ 0.016000] .... node #0, CPUs: #1
[ 0.004000] kvm-clock: cpu 1, msr 1:1ffef041, secondary cpu clock
[ 0.004000] mce: CPU supports 0 MCE banks
[ 0.018125] smp: Brought up 1 node, 2 CPUs
[ 0.018125] smpboot: Total of 2 processors activated (10848.00 BogoMIPS)
[ 0.018125] devtmpfs: initialized
[ 0.018125] x86/mm: Memory block size: 128MB
[ 0.018125] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.018125] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.018125] pinctrl core: initialized pinctrl subsystem
[ 0.018125] NET: Registered protocol family 16
[ 0.018125] cpuidle: using governor ladder
[ 0.018125] cpuidle: using governor menu
[ 0.018125] ACPI: bus type PCI registered
[ 0.018125] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.018125] PCI: Using configuration type 1 for base access
[ 0.020126] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.020126] ACPI: Added _OSI(Module Device)
[ 0.020126] ACPI: Added _OSI(Processor Device)
[ 0.020126] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.020126] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.020276] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.022477] ACPI: Interpreter enabled
[ 0.022486] ACPI: (supports S0 S5)
[ 0.022487] ACPI: Using IOAPIC for interrupt routing
[ 0.022627] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.022744] ACPI: Enabled 2 GPEs in block 00 to 07
[ 0.027205] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.027209] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI]
[ 0.027221] acpi PNP0A03:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI]
[ 0.027227] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[ 0.027455] PCI host bridge to bus 0000:00
[ 0.027457] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.027458] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.027459] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.027461] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfdffffff window]
[ 0.027462] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.027494] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000
[ 0.027961] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100
[ 0.028510] pci 0000:00:01.1: [8086:7111] type 00 class 0x01018a
[ 0.028858] pci 0000:00:01.1: reg 0x20: [io 0xd000-0xd00f]
[ 0.028989] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.028990] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.028991] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.028992] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.029190] pci 0000:00:02.0: [80ee:beef] type 00 class 0x030000
[ 0.031624] pci 0000:00:02.0: reg 0x10: [mem 0xe0000000-0xe1ffffff pref]
[ 0.044771] pci 0000:00:03.0: [8086:100e] type 00 class 0x020000
[ 0.046487] pci 0000:00:03.0: reg 0x10: [mem 0xf0000000-0xf001ffff]
[ 0.048106] pci 0000:00:03.0: reg 0x18: [io 0xd010-0xd017]
[ 0.056520] pci 0000:00:04.0: [80ee:cafe] type 00 class 0x088000
[ 0.058221] pci 0000:00:04.0: reg 0x10: [io 0xd020-0xd03f]
[ 0.059836] pci 0000:00:04.0: reg 0x14: [mem 0xf0400000-0xf07fffff]
[ 0.060089] pci 0000:00:04.0: reg 0x18: [mem 0xf0800000-0xf0803fff pref]
[ 0.068116] pci 0000:00:05.0: [8086:2415] type 00 class 0x040100
[ 0.068236] pci 0000:00:05.0: reg 0x10: [io 0xd100-0xd1ff]
[ 0.068298] pci 0000:00:05.0: reg 0x14: [io 0xd200-0xd23f]
[ 0.068774] pci 0000:00:07.0: [8086:7113] type 00 class 0x068000
[ 0.069153] pci 0000:00:07.0: quirk: [io 0x4000-0x403f] claimed by PIIX4 ACPI
[ 0.069161] pci 0000:00:07.0: quirk: [io 0x4100-0x410f] claimed by PIIX4 SMB
[ 0.069374] pci 0000:00:08.0: [8086:100e] type 00 class 0x020000
[ 0.071085] pci 0000:00:08.0: reg 0x10: [mem 0xf0820000-0xf083ffff]
[ 0.073595] pci 0000:00:08.0: reg 0x18: [io 0xd240-0xd247]
[ 0.080547] pci 0000:00:09.0: [8086:100e] type 00 class 0x020000
[ 0.082151] pci 0000:00:09.0: reg 0x10: [mem 0xf0840000-0xf085ffff]
[ 0.085607] pci 0000:00:09.0: reg 0x18: [io 0xd248-0xd24f]
[ 0.092032] pci 0000:00:0c.0: [8086:1e31] type 00 class 0x0c0330
[ 0.093620] pci 0000:00:0c.0: reg 0x10: [mem 0xf0860000-0xf086ffff]
[ 0.101909] pci 0000:00:0d.0: [8086:2829] type 00 class 0x010601
[ 0.104102] pci 0000:00:0d.0: reg 0x10: [io 0xd250-0xd257]
[ 0.105630] pci 0000:00:0d.0: reg 0x14: [io 0xd258-0xd25b]
[ 0.107171] pci 0000:00:0d.0: reg 0x18: [io 0xd260-0xd267]
[ 0.108106] pci 0000:00:0d.0: reg 0x1c: [io 0xd268-0xd26b]
[ 0.109654] pci 0000:00:0d.0: reg 0x20: [io 0xd270-0xd27f]
[ 0.112108] pci 0000:00:0d.0: reg 0x24: [mem 0xf0870000-0xf0871fff]
[ 0.114834] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 9 10 *11)
[ 0.115020] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 9 *10 11)
[ 0.115089] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 *9 10 11)
[ 0.115158] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 9 10 *11)
[ 0.116051] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.116051] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.116051] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.116051] vgaarb: loaded
[ 0.116082] EDAC MC: Ver: 3.0.0
[ 0.116298] PCI: Using ACPI for IRQ routing
[ 0.116298] PCI: pci_cache_line_size set to 64 bytes
[ 0.116298] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.116298] e820: reserve RAM buffer [mem 0xdfff0000-0xdfffffff]
[ 0.116298] clocksource: Switched to clocksource kvm-clock
[ 0.127001] VFS: Disk quotas dquot_6.6.0
[ 0.127019] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.127064] pnp: PnP ACPI init
[ 0.127116] pnp 00:00: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.127169] pnp 00:01: Plug and Play ACPI device, IDs PNP0f03 (active)
[ 0.127656] pnp: PnP ACPI: found 2 devices
[ 0.139552] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.139562] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.139564] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.139565] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.139566] pci_bus 0000:00: resource 7 [mem 0xe0000000-0xfdffffff window]
[ 0.139616] NET: Registered protocol family 2
[ 0.139736] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.139771] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.139806] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.139823] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.139832] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.139867] NET: Registered protocol family 1
[ 0.139876] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[ 0.139903] pci 0000:00:01.0: Activating ISA DMA hang workarounds
[ 0.139942] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.140869] PCI: CLS 0 bytes, default 64
[ 0.140899] Unpacking initramfs...
[ 0.503502] Freeing initrd memory: 21540K
[ 0.503512] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.503514] software IO TLB [mem 0xdbff0000-0xdfff0000] (64MB) mapped at [ffff99e79bff0000-ffff99e79ffeffff]
[ 0.503549] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2717868ea45, max_idle_ns: 440795316085 ns
[ 0.503578] platform rtc_cmos: registered platform RTC device (no PNP device found)
[ 0.503836] audit: initializing netlink subsys (disabled)
[ 0.503960] audit: type=2000 audit(1536300999.629:1): state=initialized audit_enabled=0 res=1
[ 0.504269] workingset: timestamp_bits=40 max_order=20 bucket_order=0
[ 0.504316] zbud: loaded
[ 0.505702] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.505784] io scheduler noop registered
[ 0.505784] io scheduler deadline registered
[ 0.505795] io scheduler cfq registered (default)
[ 0.505796] io scheduler mq-deadline registered
[ 0.505796] io scheduler kyber registered
[ 0.505930] intel_idle: Please enable MWAIT in BIOS SETUP
[ 0.506106] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.506561] Linux agpgart interface v0.103
[ 0.506630] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[ 0.506630] AMD IOMMUv2 functionality not available on this system
[ 0.506769] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.507182] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.507186] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.507302] mousedev: PS/2 mouse device common for all mice
[ 0.507640] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.507764] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 0.507812] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram
[ 0.507853] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.508052] NET: Registered protocol family 10
[ 0.508195] Segment Routing with IPv6
[ 0.508204] mip6: Mobile IPv6
[ 0.508205] NET: Registered protocol family 17
[ 0.508206] mpls_gso: MPLS GSO support
[ 0.508300] sched_clock: Marking stable (508278898, 0)->(873661763, -365382865)
[ 0.508633] registered taskstats version 1
[ 0.508642] zswap: loaded using pool lzo/zbud
[ 0.508775] ima: No TPM chip found, activating TPM-bypass! (rc=-19)
[ 0.508777] ima: Allocated hash algorithm: sha256
[ 0.509095] rtc_cmos rtc_cmos: setting system clock to 2018-09-07 06:16:28 UTC (1536300988)
[ 0.510316] Freeing unused kernel memory: 1524K
[ 0.528690] Write protecting the kernel read-only data: 16384k
[ 0.529207] Freeing unused kernel memory: 2012K
[ 0.530789] Freeing unused kernel memory: 1092K
[ 0.534016] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.534017] x86/mm: Checking user space page tables
[ 0.536947] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.550533] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 0.550584] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 0.550590] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 0.569430] piix4_smbus 0000:00:07.0: SMBus Host Controller at 0x4100, revision 0
[ 0.573352] SCSI subsystem initialized
[ 0.576561] libata version 3.00 loaded.
[ 0.576916] ata_piix 0000:00:01.1: version 2.13
[ 0.577235] scsi host0: ata_piix
[ 0.577280] scsi host1: ata_piix
[ 0.577301] ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xd000 irq 14
[ 0.577302] ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xd008 irq 15
[ 0.579085] ahci 0000:00:0d.0: version 3.0
[ 0.579577] ahci 0000:00:0d.0: SSS flag set, parallel bus scan disabled
[ 0.579684] ahci 0000:00:0d.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
[ 0.579686] ahci 0000:00:0d.0: flags: 64bit ncq stag only ccc
[ 0.583411] scsi host2: ahci
[ 0.583495] ata3: SATA max UDMA/133 abar m8192@0xf0870000 port 0xf0870100 irq 21
[ 0.584656] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 0.584657] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 0.586631] ACPI: bus type USB registered
[ 0.586645] usbcore: registered new interface driver usbfs
[ 0.586651] usbcore: registered new interface driver hub
[ 0.586669] usbcore: registered new device driver usb
[ 0.736321] ata1.00: ATAPI: VBOX CD-ROM, 1.0, max UDMA/133
[ 0.736622] ata1.00: configured for UDMA/33
[ 0.736942] scsi 0:0:0:0: CD-ROM VBOX CD-ROM 1.0 PQ: 0 ANSI: 5
[ 0.797149] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2
[ 0.900040] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 0.900147] ata3.00: ATA-6: VBOX HARDDISK, 1.0, max UDMA/133
[ 0.900148] ata3.00: 104857600 sectors, multi 128: LBA48 NCQ (depth 31/32)
[ 0.900220] ata3.00: configured for UDMA/133
[ 0.900309] scsi 2:0:0:0: Direct-Access ATA VBOX HARDDISK 1.0 PQ: 0 ANSI: 5
[ 0.903741] sd 2:0:0:0: [sda] 104857600 512-byte logical blocks: (53.7 GB/50.0 GiB)
[ 0.903747] sd 2:0:0:0: [sda] Write Protect is off
[ 0.903749] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.903756] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.904411] NOHZ: local_softirq_pending 80
[ 0.907899] sda: sda1 sda2 < sda5 >
[ 0.908099] sd 2:0:0:0: [sda] Attached SCSI disk
[ 0.908143] NOHZ: local_softirq_pending 80
[ 0.912082] NOHZ: local_softirq_pending 282
[ 0.927882] random: fast init done
[ 0.928246] NOHZ: local_softirq_pending 10
[ 0.936087] NOHZ: local_softirq_pending 282
[ 0.943231] device-mapper: uevent: version 1.0.3
[ 0.943505] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[ 0.956964] e1000 0000:00:03.0 eth0: (PCI:33MHz:32-bit) 08:00:27:85:8c:c9
[ 0.956967] e1000 0000:00:03.0 eth0: Intel(R) PRO/1000 Network Connection
[ 0.957458] xhci_hcd 0000:00:0c.0: xHCI Host Controller
[ 0.957466] xhci_hcd 0000:00:0c.0: new USB bus registered, assigned bus number 1
[ 0.958898] xhci_hcd 0000:00:0c.0: hcc params 0x04000000 hci version 0x100 quirks 0x0000b930
[ 0.959211] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.959213] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.959215] usb usb1: Product: xHCI Host Controller
[ 0.959216] usb usb1: Manufacturer: Linux 4.14.67 xhci-hcd
[ 0.959217] usb usb1: SerialNumber: 0000:00:0c.0
[ 0.959373] hub 1-0:1.0: USB hub found
[ 0.959407] hub 1-0:1.0: 8 ports detected
[ 0.959698] xhci_hcd 0000:00:0c.0: xHCI Host Controller
[ 0.959702] xhci_hcd 0000:00:0c.0: new USB bus registered, assigned bus number 2
[ 0.959706] xhci_hcd 0000:00:0c.0: Host supports USB 3.0 SuperSpeed
[ 0.959850] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.959852] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.959853] usb usb2: Product: xHCI Host Controller
[ 0.959854] usb usb2: Manufacturer: Linux 4.14.67 xhci-hcd
[ 0.959856] usb usb2: SerialNumber: 0000:00:0c.0
[ 0.960110] hub 2-0:1.0: USB hub found
[ 0.960137] hub 2-0:1.0: 6 ports detected
[ 0.976293] NOHZ: local_softirq_pending 282
[ 0.988884] sr 0:0:0:0: [sr0] scsi3-mmc drive: 32x/32x xa/form2 tray
[ 0.988885] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 0.989337] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.296924] usb 1-1: new full-speed USB device number 2 using xhci_hcd
[ 1.324461] e1000 0000:00:08.0 eth1: (PCI:33MHz:32-bit) 08:00:27:ea:bf:13
[ 1.324463] e1000 0000:00:08.0 eth1: Intel(R) PRO/1000 Network Connection
[ 1.444792] usb 1-1: New USB device found, idVendor=80ee, idProduct=0021
[ 1.444794] usb 1-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0
[ 1.444795] usb 1-1: Product: USB Tablet
[ 1.444796] usb 1-1: Manufacturer: VirtualBox
[ 1.447770] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.449784] usbcore: registered new interface driver usbhid
[ 1.449786] usbhid: USB HID core driver
[ 1.450608] input: VirtualBox USB Tablet as /devices/pci0000:00/0000:00:0c.0/usb1/1-1/1-1:1.0/0003:80EE:0021.0001/input/input3
[ 1.450782] hid-generic 0003:80EE:0021.0001: input,hidraw0: USB HID v1.10 Mouse [VirtualBox USB Tablet] on usb-0000:00:0c.0-1/input0
[ 1.714720] e1000 0000:00:09.0 eth2: (PCI:33MHz:32-bit) 08:00:27:71:5d:db
[ 1.714727] e1000 0000:00:09.0 eth2: Intel(R) PRO/1000 Network Connection
[ 1.717725] e1000 0000:00:08.0 enp0s8: renamed from eth1
[ 1.729075] e1000 0000:00:09.0 enp0s9: renamed from eth2
[ 1.761014] e1000 0000:00:03.0 enp0s3: renamed from eth0
[ 1.804099] NOHZ: local_softirq_pending 282
[ 1.816072] NOHZ: local_softirq_pending 10
[ 1.835819] PM: Starting manual resume from disk
[ 1.836003] PM: Image not found (code -22)
[ 1.935106] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 1.936087] NOHZ: local_softirq_pending 10
[ 1.948081] NOHZ: local_softirq_pending 282
[ 2.097649] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.104168] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 2.104198] systemd[1]: Detected virtualization oracle.
[ 2.104201] systemd[1]: Detected architecture x86-64.
[ 2.106901] systemd[1]: Set hostname to <debian>.
[ 2.243502] systemd[1]: Listening on udev Kernel Socket.
[ 2.244682] systemd[1]: Created slice User and Session Slice.
[ 2.244722] systemd[1]: Listening on Journal Socket (/dev/log).
[ 2.244844] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 2.245035] systemd[1]: Created slice System Slice.
[ 2.245583] systemd[1]: Mounting Huge Pages File System...
[ 2.519061] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[ 2.585228] systemd-journald[179]: Received request to flush runtime journal from PID 1
[ 2.682117] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 2.682155] ACPI: Power Button [PWRF]
[ 2.682231] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input5
[ 2.682237] ACPI: Sleep Button [SLPF]
[ 2.705310] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 2.705334] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.718192] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 2.718243] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input6
[ 2.783586] vboxguest: loading out-of-tree module taints kernel.
[ 2.790442] vgdrvHeartbeatInit: Setting up heartbeat to trigger every 2000 milliseconds
[ 2.790985] input: Unspecified device as /devices/pci0000:00/0000:00:04.0/input/input7
[ 2.792513] vboxguest: misc device minor 58, IRQ 20, I/O port d020, MMIO at 00000000f0400000 (size 0x400000)
[ 2.792557] vboxguest: Successfully loaded version 5.2.8 (interface 0x00010004)
[ 2.793310] ACPI: Battery Slot [BAT0] (battery present)
[ 2.793509] ACPI: AC Adapter [AC] (on-line)
[ 2.803539] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 2.807849] Error: Driver 'pcspkr' is already registered, aborting...
[ 2.848275] RAPL PMU: API unit is 2^-32 Joules, 5 fixed counters, 10737418240 ms ovfl timer
[ 2.848276] RAPL PMU: hw unit of domain pp0-core 2^-0 Joules
[ 2.848277] RAPL PMU: hw unit of domain package 2^-0 Joules
[ 2.848277] RAPL PMU: hw unit of domain dram 2^-0 Joules
[ 2.848278] RAPL PMU: hw unit of domain pp1-gpu 2^-0 Joules
[ 2.848278] RAPL PMU: hw unit of domain psys 2^-0 Joules
[ 2.882770] [drm] VRAM 02000000
[ 2.885552] [TTM] Zone kernel: Available graphics memory: 2021900 kiB
[ 2.885553] [TTM] Initializing pool allocator
[ 2.885555] [TTM] Initializing DMA pool allocator
[ 2.888033] fbcon: vboxdrmfb (fb0) is primary device
[ 2.890499] Console: switching to colour frame buffer device 100x37
[ 2.891258] vboxvideo 0000:00:02.0: fb0: vboxdrmfb frame buffer device
[ 2.909905] [drm] Initialized vboxvideo 1.0.0 20130823 for 0000:00:02.0 on minor 0
[ 2.961303] AVX2 version of gcm_enc/dec engaged.
[ 2.961304] AES CTR mode by8 optimization enabled
[ 3.059749] alg: No test for pcbc(aes) (pcbc-aes-aesni)
[ 3.068475] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[ 3.070961] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 3.868506] random: crng init done
[ 3.868508] random: 7 urandom warning(s) missed due to ratelimiting
[ 4.180885] IPv6: ADDRCONF(NETDEV_UP): enp0s9: link is not ready
[ 4.187159] e1000: enp0s9 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
[ 4.189233] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s9: link becomes ready
[ 4.209549] snd_intel8x0 0000:00:05.0: white list rate for 1028:0177 is 48000
[ 4.263821] IPv6: ADDRCONF(NETDEV_UP): enp0s3: link is not ready
[ 4.268546] e1000: enp0s3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
[ 4.268817] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s3: link becomes ready
[ 4.309586] Adding 2097148k swap on /dev/mapper/debian--vg-swap_1. Priority:-2 extents:1 across:2097148k FS
[ 5.308980] vboxsf: Successfully loaded version 5.2.8 (interface 0x00010004)
[ 6.016273] VBoxService 5.2.8 r121009 (verbosity: 0) linux.amd64 (Feb 26 2018 15:59:51) release log
00:00:00.000109 main Log opened 2018-09-07T06:16:34.007069000Z
[ 6.016613] 00:00:00.000468 main OS Product: Linux
[ 6.016649] 00:00:00.000547 main OS Release: 4.14.67
[ 6.016679] 00:00:00.000580 main OS Version: #1 SMP Wed Sep 5 12:27:57 CEST 2018
[ 6.016715] 00:00:00.000609 main Executable: /opt/VBoxGuestAdditions-5.2.8/sbin/VBoxService
00:00:00.000610 main Process ID: 621
00:00:00.000611 main Package type: LINUX_64BITS_GENERIC
[ 6.017822] 00:00:00.001705 main 5.2.8 r121009 started. Verbose level = 0
[ 6.403318] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 6.405037] Bridge firewalling registered
[ 6.417911] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 6.813945] Initializing XFRM netlink socket
[ 6.817954] Netfilter messages via NETLINK v0.30.
[ 6.820109] ctnetlink v0.93: registering with nfnetlink.
[ 6.986897] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready
[ 108.685119] usb 1-2: new high-speed USB device number 3 using xhci_hcd
[ 108.947519] usb 1-2: New USB device found, idVendor=13b1, idProduct=0042
[ 108.947522] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 108.947523] usb 1-2: Product: USBWLAN
[ 108.947524] usb 1-2: Manufacturer: Qualcomm Atheros
[ 108.947525] usb 1-2: SerialNumber: 12345678
[ 109.066597] usb 1-2: usb new func vendor 0x13b1 product 0x0042
[ 109.066600] usb 1-2: usb setting up pipes using interface
[ 109.066602] usb 1-2: usb rx bulk ep 0x81 maxpktsz 512
[ 109.066607] usb 1-2: usb alloc resources lpipe 4 hpipe 0xc0408380 urbs 32
[ 109.066608] usb 1-2: usb rx bulk ep 0x82 maxpktsz 512
[ 109.066612] usb 1-2: usb alloc resources lpipe 5 hpipe 0xc0410380 urbs 32
[ 109.066613] usb 1-2: usb rx bulk ep 0x83 maxpktsz 512
[ 109.066617] usb 1-2: usb alloc resources lpipe 6 hpipe 0xc0418380 urbs 32
[ 109.066618] usb 1-2: usb rx bulk ep 0x84 maxpktsz 512
[ 109.066621] usb 1-2: usb alloc resources lpipe 7 hpipe 0xc0420380 urbs 32
[ 109.066622] usb 1-2: usb tx bulk ep 0x01 maxpktsz 512
[ 109.066627] usb 1-2: usb alloc resources lpipe 0 hpipe 0xc0008300 urbs 32
[ 109.066628] usb 1-2: usb tx bulk ep 0x02 maxpktsz 512
[ 109.066631] usb 1-2: usb alloc resources lpipe 1 hpipe 0xc0010300 urbs 32
[ 109.066632] usb 1-2: usb tx bulk ep 0x03 maxpktsz 512
[ 109.066636] usb 1-2: usb alloc resources lpipe 2 hpipe 0xc0018300 urbs 32
[ 109.066638] usb 1-2: usb tx bulk ep 0x04 maxpktsz 512
[ 109.066641] usb 1-2: usb alloc resources lpipe 3 hpipe 0xc0020300 urbs 32
[ 109.066643] usb 1-2: WARNING: ath10k USB support is incomplete, don't expect anything to work!
[ 109.066647] usb 1-2: bmi get target info
[ 109.066706] usbcore: registered new interface driver ath10k_usb
[ 109.067242] usb 1-2: Hardware name qca9377 hw1.1 version 0x5020001
[ 109.076476] usb 1-2: Direct firmware load for ath10k/pre-cal-usb-1-2.bin failed with error -2
[ 109.076479] usb 1-2: boot fw request 'ath10k/pre-cal-usb-1-2.bin': -2
[ 109.076491] usb 1-2: Direct firmware load for ath10k/cal-usb-1-2.bin failed with error -2
[ 109.076493] usb 1-2: boot fw request 'ath10k/cal-usb-1-2.bin': -2
[ 109.076494] usb 1-2: trying fw api 6
[ 109.077322] usb 1-2: Direct firmware load for ath10k/QCA9377/hw1.0/firmware-usb-6.bin failed with error -2
[ 109.077325] usb 1-2: boot fw request 'ath10k/QCA9377/hw1.0/firmware-usb-6.bin': -2
[ 109.077326] usb 1-2: trying fw api 5
[ 109.083351] usb 1-2: boot fw request 'ath10k/QCA9377/hw1.0/firmware-usb-5.bin': 0
[ 109.083353] usb 1-2: found fw version CNSS.TF.1.0-00267-QCATFSWPZ-1
[ 109.083354] usb 1-2: found fw timestamp 1502520305
[ 109.083356] usb 1-2: found otp image ie (23749 B)
[ 109.083357] usb 1-2: found fw image ie (582052 B)
[ 109.083358] usb 1-2: found firmware features ie (1 B)
[ 109.083359] usb 1-2: Enabling feature bit: 7
[ 109.083360] usb 1-2: features
[ 109.083361] usb 1-2: 00000000: 80 00 00 00 00 00 00 00 ........
[ 109.083362] usb 1-2: found fw ie wmi op version 4
[ 109.083363] usb 1-2: found fw ie htt op version 3
[ 109.083364] usb 1-2: using fw api 5
[ 109.083367] usb 1-2: qca9377 hw1.1 target 0x05020001 chip_id 0x00000000 sub 0000:0000
[ 109.083368] usb 1-2: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 0
[ 109.083718] usb 1-2: firmware ver CNSS.TF.1.0-00267-QCATFSWPZ-1 api 5 features ignore-otp crc32 d6b81b3c
[ 109.083720] usb 1-2: boot did not find a pre calibration file, try DT next: -2
[ 109.083721] usb 1-2: unable to load pre cal data from DT: -2
[ 109.083722] usb 1-2: could not load pre cal data: -2
[ 109.083723] usb 1-2: boot upload otp to 0x1234 len 23749 for board id
[ 109.083725] usb 1-2: bmi fast download address 0x1234 buffer 0xffffa68fc0d7a048 length 23749
[ 109.083726] usb 1-2: bmi lz stream start address 0x1234
[ 109.084172] usb 1-2: bmi lz data buffer 0xffffa68fc0d7a048 length 23748
[ 109.119415] usb 1-2: bmi lz data buffer 0xffffa68fc0967ddc length 4
[ 109.119599] usb 1-2: bmi lz stream start address 0x0
[ 109.119776] usb 1-2: bmi execute address 0x1234 param 0x10
[ 109.120255] usb 1-2: bmi execute result 0x1
[ 109.120257] usb 1-2: boot get otp board id result 0x00000001 board_id 0 chip_id 0
[ 109.120259] usb 1-2: board id does not exist in otp, ignore it
[ 109.120278] usb 1-2: bdf variant name not set.
[ 109.120281] usb 1-2: boot using board name 'bus=usb,vendor=13b1,device=0042,subsystem-vendor=0000,subsystem-device=0000'
[ 109.129067] usb 1-2: boot fw request 'ath10k/QCA9377/hw1.0/board-2.bin': 0
[ 109.129070] usb 1-2: board name
[ 109.129072] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129074] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129075] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129077] usb 1-2: 00000030: 3d 31 36 39 63 2c 73 75 62 73 79 73 74 65 6d 2d =169c,subsystem-
[ 109.129078] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 36 35 device=3365
[ 109.129080] usb 1-2: board name
[ 109.129082] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129083] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129085] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129087] usb 1-2: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 74 65 6d 2d =168c,subsystem-
[ 109.129088] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 34 66 device=334f
[ 109.129091] usb 1-2: board name
[ 109.129093] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129095] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129096] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129098] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129100] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 32 62 device=412b
[ 109.129101] usb 1-2: board name
[ 109.129103] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129105] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129106] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129108] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129110] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 32 63 device=412c
[ 109.129111] usb 1-2: board name
[ 109.129113] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129115] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129116] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129118] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129120] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 32 64 device=412d
[ 109.129121] usb 1-2: board name
[ 109.129123] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129125] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129127] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129128] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129130] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 32 65 device=412e
[ 109.129132] usb 1-2: board name
[ 109.129134] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129135] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129137] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129139] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129141] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 33 33 device=4133
[ 109.129142] usb 1-2: board name
[ 109.129144] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129146] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129148] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129149] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129151] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 33 31 device=2231
[ 109.129152] usb 1-2: board name
[ 109.129154] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129156] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129158] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129159] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129161] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 62 33 31 device=2b31
[ 109.129162] usb 1-2: board name
[ 109.129164] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129165] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129168] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129170] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129171] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 63 33 31 device=2c31
[ 109.129173] usb 1-2: board name
[ 109.129175] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129177] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129178] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129180] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129183] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 64 33 31 device=2d31
[ 109.129184] usb 1-2: board name
[ 109.129185] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129186] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129187] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129188] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129189] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 66 33 31 device=2f31
[ 109.129191] usb 1-2: board name
[ 109.129192] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129193] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129194] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129195] usb 1-2: 00000030: 3d 31 34 34 66 2c 73 75 62 73 79 73 74 65 6d 2d =144f,subsystem-
[ 109.129196] usb 1-2: 00000040: 64 65 76 69 63 65 3d 37 31 34 35 device=7145
[ 109.129197] usb 1-2: board name
[ 109.129199] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129200] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129202] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129204] usb 1-2: 00000030: 3d 31 30 35 62 2c 73 75 62 73 79 73 74 65 6d 2d =105b,subsystem-
[ 109.129205] usb 1-2: 00000040: 64 65 76 69 63 65 3d 65 30 39 61 device=e09a
[ 109.129206] usb 1-2: board name
[ 109.129207] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129208] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129210] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129211] usb 1-2: 00000030: 3d 31 31 61 64 2c 73 75 62 73 79 73 74 65 6d 2d =11ad,subsystem-
[ 109.129212] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 38 30 36 device=0806
[ 109.129213] usb 1-2: board name
[ 109.129214] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129215] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129217] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129219] usb 1-2: 00000030: 3d 31 31 61 64 2c 73 75 62 73 79 73 74 65 6d 2d =11ad,subsystem-
[ 109.129220] usb 1-2: 00000040: 64 65 76 69 63 65 3d 31 38 30 36 device=1806
[ 109.129222] usb 1-2: board name
[ 109.129224] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129225] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129226] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129228] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129229] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 32 33 35 device=4235
[ 109.129230] usb 1-2: board name
[ 109.129231] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129232] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129233] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129234] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129235] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 33 33 35 device=4335
[ 109.129236] usb 1-2: board name
[ 109.129238] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129239] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129240] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129241] usb 1-2: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 74 65 6d 2d =168c,subsystem-
[ 109.129243] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 36 35 device=3365
[ 109.129245] usb 1-2: board name
[ 109.129247] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129248] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129249] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129250] usb 1-2: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 74 65 6d 2d =168c,subsystem-
[ 109.129252] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 36 39 device=3369
[ 109.129253] usb 1-2: board name
[ 109.129254] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129255] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129256] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129258] usb 1-2: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 74 65 6d 2d =168c,subsystem-
[ 109.129259] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 36 38 device=3368
[ 109.129261] usb 1-2: board name
[ 109.129263] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129264] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129266] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129267] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129269] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 33 61 device=223a
[ 109.129270] usb 1-2: board name
[ 109.129271] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129272] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129273] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129274] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129275] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 33 62 device=223b
[ 109.129276] usb 1-2: board name
[ 109.129278] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129279] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129280] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129281] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129282] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 33 63 device=223c
[ 109.129283] usb 1-2: board name
[ 109.129285] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129286] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129288] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129290] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129291] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 35 31 device=2251
[ 109.129292] usb 1-2: board name
[ 109.129293] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129294] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129295] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129296] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129297] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 62 35 31 device=2b51
[ 109.129298] usb 1-2: board name
[ 109.129299] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129301] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129302] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129304] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129306] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 63 35 31 device=2c51
[ 109.129308] usb 1-2: board name
[ 109.129310] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129311] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129312] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129313] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129314] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 61 35 31 device=2a51
[ 109.129315] usb 1-2: board name
[ 109.129316] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129318] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129319] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129320] usb 1-2: 00000030: 3d 31 34 34 66 2c 73 75 62 73 79 73 74 65 6d 2d =144f,subsystem-
[ 109.129321] usb 1-2: 00000040: 64 65 76 69 63 65 3d 37 31 34 32 device=7142
[ 109.129322] usb 1-2: board name
[ 109.129323] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129325] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129326] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129328] usb 1-2: 00000030: 3d 31 31 61 64 2c 73 75 62 73 79 73 74 65 6d 2d =11ad,subsystem-
[ 109.129329] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 35 30 37 device=0507
[ 109.129331] usb 1-2: board name
[ 109.129332] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129333] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129334] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129335] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129336] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 35 31 30 device=2510
[ 109.129338] usb 1-2: board name
[ 109.129339] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129340] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129341] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129342] usb 1-2: 00000030: 3d 31 31 61 64 2c 73 75 62 73 79 73 74 65 6d 2d =11ad,subsystem-
[ 109.129344] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 38 61 36 device=08a6
[ 109.129345] usb 1-2: board name
[ 109.129347] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129348] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129350] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129351] usb 1-2: 00000030: 3d 31 30 35 62 2c 73 75 62 73 79 73 74 65 6d 2d =105b,subsystem-
[ 109.129352] usb 1-2: 00000040: 64 65 76 69 63 65 3d 65 30 61 31 device=e0a1
[ 109.129353] usb 1-2: board name
[ 109.129354] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129355] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129357] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129358] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129359] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 30 33 35 device=4035
[ 109.129360] usb 1-2: board name
[ 109.129361] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129362] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129364] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129365] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129366] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 33 35 device=4135
[ 109.129396] usb 1-2: board name
[ 109.129399] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129401] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129402] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129404] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129405] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 39 30 31 device=0901
[ 109.129407] usb 1-2: board name
[ 109.129408] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129410] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129411] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129413] usb 1-2: 00000030: 3d 31 30 32 38 2c 73 75 62 73 79 73 74 65 6d 2d =1028,subsystem-
[ 109.129415] usb 1-2: 00000040: 64 65 76 69 63 65 3d 31 38 31 30 device=1810
[ 109.129417] usb 1-2: board name
[ 109.129419] usb 1-2: 00000000: 62 75 73 3d 75 73 62 2c 76 65 6e 64 6f 72 3d 31 bus=usb,vendor=1
[ 109.129421] usb 1-2: 00000010: 33 62 31 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 3b1,device=0042,
[ 109.129422] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129425] usb 1-2: 00000030: 3d 30 30 30 30 2c 73 75 62 73 79 73 74 65 6d 2d =0000,subsystem-
[ 109.129426] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 30 30 30 device=0000
[ 109.129428] usb 1-2: boot found match for name 'bus=usb,vendor=13b1,device=0042,subsystem-vendor=0000,subsystem-device=0000'
[ 109.129429] usb 1-2: boot found board data for 'bus=usb,vendor=13b1,device=0042,subsystem-vendor=0000,subsystem-device=0000'
[ 109.129431] usb 1-2: using board api 2
[ 109.129620] usb 1-2: board_file api 2 bmi_id N/A crc32 22a1f6f4
[ 109.129623] usb 1-2: bmi start
[ 109.129625] usb 1-2: bmi read soc register 0x00000b2c
[ 109.130397] usb 1-2: bmi read soc register value 0x00000080
[ 109.130399] usb 1-2: bmi read soc register 0x00000af4
[ 109.131056] usb 1-2: bmi read soc register value 0x0006aaa8
[ 109.131057] usb 1-2: bmi write soc register 0x00000af4 val 0x0006aaa8
[ 109.131292] usb 1-2: bmi read soc register 0x00001018
[ 109.131662] usb 1-2: bmi read soc register value 0x00000160
[ 109.131664] usb 1-2: bmi write soc register 0x00001018 val 0x00000160
[ 109.131841] usb 1-2: bmi read soc register 0x00000914
[ 109.132233] usb 1-2: bmi read soc register value 0x00000001
[ 109.132235] usb 1-2: bmi write soc register 0x00000914 val 0x00000001
[ 109.132440] usb 1-2: bmi write address 0x404028 length 4
[ 109.132640] usb 1-2: bmi read soc register 0x00001014
[ 109.133031] usb 1-2: bmi read soc register value 0x0000000e
[ 109.133032] usb 1-2: bmi write soc register 0x00001014 val 0x0004000e
[ 109.133226] usb 1-2: bmi read soc register 0x00001244
[ 109.133596] usb 1-2: bmi read soc register value 0x00000002
[ 109.133597] usb 1-2: bmi read soc register 0x00001014
[ 109.133959] usb 1-2: bmi read soc register value 0x0004000e
[ 109.133960] usb 1-2: bmi write soc register 0x00001014 val 0x0004000e
[ 109.134142] usb 1-2: bmi read soc register 0x00001244
[ 109.134501] usb 1-2: bmi read soc register value 0x00000002
[ 109.134503] usb 1-2: bmi read soc register 0x00000820
[ 109.134858] usb 1-2: bmi read soc register value 0x00000001
[ 109.134859] usb 1-2: bmi write soc register 0x00000820 val 0x00000001
[ 109.135047] usb 1-2: bmi read soc register 0x00001014
[ 109.135407] usb 1-2: bmi read soc register value 0x0004000e
[ 109.135408] usb 1-2: bmi write soc register 0x00001014 val 0x0000000e
[ 109.135594] usb 1-2: bmi write address 0x404020 length 4
[ 109.135777] usb 1-2: bmi write address 0x404024 length 4
[ 109.135969] usb 1-2: bmi enable pll ret 0
[ 109.135971] usb 1-2: bmi write address 0x400800 length 4
[ 109.136655] usb 1-2: bmi read address 0x400810 length 4
[ 109.137040] usb 1-2: bmi write address 0x400810 length 4
[ 109.137235] usb 1-2: bmi write address 0x400844 length 4
[ 109.137436] usb 1-2: bmi write address 0x400904 length 4
[ 109.137636] usb 1-2: bmi write address 0x4008bc length 4
[ 109.137833] usb 1-2: boot did not find a pre calibration file, try DT next: -2
[ 109.137834] usb 1-2: unable to load pre cal data from DT: -2
[ 109.137835] usb 1-2: failed to load pre cal data: -2
[ 109.137836] usb 1-2: pre cal download procedure failed, try cal file: -2
[ 109.137837] usb 1-2: boot did not find a calibration file, try DT next: -2
[ 109.137838] usb 1-2: boot did not find DT entry, try target EEPROM next: -2
[ 109.137839] usb 1-2: boot did not find target EEPROM entry, try OTP next: -95
[ 109.137841] usb 1-2: bmi read address 0x4008ac length 4
[ 109.139278] usb 1-2: boot push board extended data addr 0x0
[ 109.139280] usb 1-2: bmi read address 0x400854 length 4
[ 109.139843] usb 1-2: bmi write address 0x401fc0 length 8124
[ 109.152458] usb 1-2: bmi write address 0x400858 length 4
[ 109.152646] usb 1-2: boot upload otp to 0x1234 len 23749
[ 109.152647] usb 1-2: bmi fast download address 0x1234 buffer 0xffffa68fc0d7a048 length 23749
[ 109.152648] usb 1-2: bmi lz stream start address 0x1234
[ 109.152834] usb 1-2: bmi lz data buffer 0xffffa68fc0d7a048 length 23748
[ 109.190512] usb 1-2: bmi lz data buffer 0xffffa68fc0967d8c length 4
[ 109.190752] usb 1-2: bmi lz stream start address 0x0
[ 109.191010] usb 1-2: bmi execute address 0x1234 param 0x0
[ 109.192025] usb 1-2: bmi execute result 0x3
[ 109.192026] usb 1-2: boot otp execute result 3
[ 109.192028] usb 1-2: boot using calibration mode otp
[ 109.192029] usb 1-2: boot uploading firmware image ffffa68fc0d7fd18 len 582052
[ 109.192031] usb 1-2: bmi fast download address 0x1234 buffer 0xffffa68fc0d7fd18 length 582052
[ 109.192032] usb 1-2: bmi lz stream start address 0x1234
[ 109.192281] usb 1-2: bmi lz data buffer 0xffffa68fc0d7fd18 length 582052
[ 110.253443] usb 1-2: bmi lz stream start address 0x0
[ 110.253696] usb 1-2: bmi write address 0x400814 length 4
[ 110.253948] usb 1-2: boot htc service 'Control' ul pipe 0 dl pipe 5 eid 0 ready
[ 110.253951] usb 1-2: boot htc service 'Control' eid 0 TX flow control disabled
[ 110.253953] usb 1-2: bmi done
[ 110.254202] usb 1-2: htt tx max num pending tx 1056
[ 110.254218] usb 1-2: htt rx ring size 2048 fill_level 1023
[ 110.254225] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d63ab700
[ 110.254241] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d4b16900
[ 110.254252] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798543600
[ 110.254262] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5020900
[ 110.254272] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5043300
[ 110.254286] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d944b700
[ 110.254303] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fc400
[ 110.254316] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d944bc00
[ 110.254329] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fce00
[ 110.254343] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fc900
[ 110.254355] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4f00
[ 110.254370] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55f2d00
[ 110.254383] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4600
[ 110.254397] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4d00
[ 110.254410] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4b00
[ 110.254422] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5c00
[ 110.254433] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5200
[ 110.254446] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5f00
[ 110.254460] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5028f00
[ 110.254471] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5028200
[ 110.254482] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d8b6b400
[ 110.254494] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d503a600
[ 110.254505] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d503a000
[ 110.254517] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d50ac700
[ 110.254533] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55f0200
[ 110.254561] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5020800
[ 110.254576] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d7554e00
[ 110.254587] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5023100
[ 110.254599] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fcd00
[ 110.254611] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55cd800
[ 110.254623] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d501db00
[ 110.254634] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d9452900
[ 110.259198] usb 1-2: usb recv pipe 5 stat 0 len 20 urb 0xffff99e7d7c10540
[ 110.259208] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d50bc000
[ 110.263917] usb 1-2: Target ready! transmit resources: 3 size:1792
[ 110.263920] usb 1-2: Extended ready message. RX bundle size: 0
[ 110.263922] usb 1-2: boot htc service HTT Data does not allocate target credits
[ 110.263926] usb 1-2: ath10k_htc_build_tx_ctrl_skb: skb ffff99e7d63ab700
[ 110.264168] usb 1-2: usb recv pipe 5 stat 0 len 20 urb 0xffff99e7d7c10600
[ 110.264175] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798442200
[ 110.264233] usb 1-2: ath10k_htc_notify_tx_completion: ep 0 skb ffff99e7d63ab700
[ 110.264244] usb 1-2: HTC Service HTT Data connect response: status: 0x0, assigned ep: 0x1
[ 110.264247] usb 1-2: boot htc service 'HTT Data' ul pipe 1 dl pipe 5 eid 1 ready
[ 110.264249] usb 1-2: boot htc service 'HTT Data' eid 1 TX flow control disabled
[ 110.264253] usb 1-2: ath10k_htc_build_tx_ctrl_skb: skb ffff99e7d4b16900
[ 110.264546] usb 1-2: usb recv pipe 5 stat 0 len 20 urb 0xffff99e7d7c10480
[ 110.264553] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d63ab700
[ 110.264607] usb 1-2: ath10k_htc_notify_tx_completion: ep 0 skb ffff99e7d4b16900
[ 110.264616] usb 1-2: HTC Service WMI connect response: status: 0x0, assigned ep: 0x2
[ 110.264619] usb 1-2: boot htc service 'WMI' ul pipe 0 dl pipe 5 eid 2 ready
[ 110.264622] usb 1-2: ath10k_htc_build_tx_ctrl_skb: skb ffff99e798543600
[ 110.264624] usb 1-2: HTC is using TX credit flow control
[ 110.264939] usb 1-2: usb recv pipe 5 stat 0 len 12 urb 0xffff99e7d7c10180
[ 110.264944] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e793a4b700
[ 110.265001] usb 1-2: usb recv pipe 5 stat 0 len 296 urb 0xffff99e7d7c10000
[ 110.265010] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798442a00
[ 110.265056] usb 1-2: ath10k_htc_notify_tx_completion: ep 0 skb ffff99e798543600
[ 110.265062] usb 1-2: htt rx, msg_type: 0xF
[ 110.265139] usb 1-2: wmi tlv abi 0x01000000 ?= 0x01000000, 0x5f414351 ?= 0x5f414351, 0x00004c4d ?= 0x00004c4d, 0x00000000 ?= 0x00000000, 0x00000000 ?= 0x00000000
[ 110.265145] usb 1-2: wmi svc: 00000000: 0d 00 00 00 07 00 00 00 0f 00 00 00 03 00 00 00 ................
[ 110.265148] usb 1-2: wmi svc: 00000010: 0f 00 00 00 0f 00 00 00 0b 00 00 00 0f 00 00 00 ................
[ 110.265150] usb 1-2: wmi svc: 00000020: 0b 00 00 00 0b 00 00 00 04 00 00 00 0a 00 00 00 ................
[ 110.265153] usb 1-2: wmi svc: 00000030: 01 00 00 00 00 00 00 00 08 00 00 00 00 00 00 00 ................
[ 110.265155] usb 1-2: wmi svc: 00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 110.265157] usb 1-2: wmi svc: 00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 110.265159] usb 1-2: wmi svc: 00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 110.265162] usb 1-2: wmi svc: 00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 110.265167] usb 1-2: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000085b vht_cap 0x339011b2 sw_ver0 0x01000000 sw_ver1 0x0000003d fw_build 0x10358701 phy_capab 0x00000003 num_rf_chains 0x00000001 eeprom_rd 0x00000037 num_mem_reqs 0x00000000
[ 110.265210] usb 1-2: firmware CNSS.TF.1.0-00267-QCATFSWPZ-1 booted
[ 110.265214] usb 1-2: wmi tlv init
[ 110.265217] usb 1-2: htc ep 2 consumed 1 credits (total 2)
[ 110.265514] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e7d9477f00
[ 110.272012] usb 1-2: usb recv pipe 5 stat 0 len 1500 urb 0xffff99e7d77cf480
[ 110.272023] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5681e00
[ 110.272084] usb 1-2: wmi event debug mesg len 1488
[ 110.273351] usb 1-2: usb recv pipe 5 stat 0 len 52 urb 0xffff99e7d77cf600
[ 110.273363] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d4b16c00
[ 110.273382] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf6c0
[ 110.273390] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d4b16800
[ 110.273451] usb 1-2: wmi event ready sw_version 16777216 abi_version 61 mac_addr 24:f5:a2:73:d2:51 status 0
[ 110.273458] usb 1-2: htc ep 2 got 1 credits (total 3)
[ 110.273466] usb 1-2: wmi tlv vdev create
[ 110.273469] usb 1-2: htc ep 2 consumed 1 credits (total 2)
[ 110.273483] usb 1-2: wmi tlv vdev delete
[ 110.273486] usb 1-2: htc ep 2 consumed 1 credits (total 1)
[ 110.273497] usb 1-2: wmi tlv echo value 0x0ba991e9
[ 110.273499] usb 1-2: htc ep 2 consumed 1 credits (total 0)
[ 110.273793] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e7d944bc00
[ 110.273798] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e7d55fc400
[ 110.273800] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e7d6bc6200
[ 110.274074] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cfd80
[ 110.274084] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d944bc00
[ 110.274200] usb 1-2: htc ep 2 got 1 credits (total 1)
[ 110.274277] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf840
[ 110.274287] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fce00
[ 110.274304] usb 1-2: usb recv pipe 5 stat 0 len 20 urb 0xffff99e7d77cff00
[ 110.274308] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e793a4ae00
[ 110.274325] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf9c0
[ 110.274331] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5594700
[ 110.274372] usb 1-2: htc ep 2 got 1 credits (total 2)
[ 110.274377] usb 1-2: wmi event echo value 0x0ba991e9
[ 110.274382] usb 1-2: htc ep 2 got 1 credits (total 3)
[ 110.274965] usb 1-2: ath10k_htc_notify_tx_completion: ep 1 skb ffff99e798715200
[ 110.275060] usb 1-2: usb recv pipe 5 stat 0 len 12 urb 0xffff99e7d77cf000
[ 110.275068] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715200
[ 110.275126] usb 1-2: htt rx, msg_type: 0x0
[ 110.275134] usb 1-2: htt target version 3.1
[ 110.275149] usb 1-2: htt h2t aggr cfg msg amsdu 3 ampdu 64
[ 110.275159] usb 1-2: wmi tlv pktlog disable
[ 110.275162] usb 1-2: htc ep 2 consumed 1 credits (total 2)
[ 110.275174] usb 1-2: htt-ver 3.1 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[ 110.275486] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e798715f00
[ 110.275490] usb 1-2: ath10k_htc_notify_tx_completion: ep 1 skb ffff99e7d55d4600
[ 110.275493] usb 1-2: ath10k_htc_notify_tx_completion: ep 1 skb ffff99e798715b00
[ 110.275561] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf540
[ 110.275599] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715b00
[ 110.275711] usb 1-2: htc ep 2 got 1 credits (total 3)
[ 110.277321] usb 1-2: wmi tlv pktlog disable
[ 110.277325] usb 1-2: htc ep 2 consumed 1 credits (total 2)
[ 110.277340] usb 1-2: wmi tlv pdev suspend
[ 110.277343] usb 1-2: htc ep 2 consumed 1 credits (total 1)
[ 110.277644] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e798715c00
[ 110.277648] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e798715500
[ 110.277785] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf0c0
[ 110.277796] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715500
[ 110.277818] usb 1-2: usb recv pipe 5 stat 0 len 1336 urb 0xffff99e7d77cfb40
[ 110.277824] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715c00
[ 110.277841] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf240
[ 110.277849] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798716600
[ 110.277861] usb 1-2: usb recv pipe 5 stat 0 len 12 urb 0xffff99e7d77cf180
[ 110.277866] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798716900
[ 110.277914] usb 1-2: htc ep 2 got 1 credits (total 2)
[ 110.277919] usb 1-2: wmi event debug mesg len 1324
[ 110.277922] usb 1-2: htc ep 2 got 1 credits (total 3)
[ 110.277925] usb 1-2: boot suspend complete
[ 110.278229] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf240
[ 110.278412] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cfb40
[ 110.278595] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf0c0
[ 110.278778] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf540
[ 110.278927] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf9c0
[ 110.279078] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7da444480
[ 110.279145] usb 1-2: usb recv pipe 5 stat 0 len 244 urb 0xffff99e7d77cfcc0
[ 110.279149] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715200
[ 110.279152] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715c00
[ 110.279153] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5200
[ 110.279155] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5c00
[ 110.279157] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4b00
[ 110.279159] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798716300
[ 110.279161] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798716e00
[ 110.279167] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cff00
[ 110.279195] usb 1-2: zero length frame received, firmware crashed?
[ 110.279315] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf000
[ 110.279466] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf240
[ 110.279614] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cfb40
[ 110.279767] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf0c0
[ 110.279948] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf540
[ 110.280106] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf9c0
[ 110.280254] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7da444480
[ 110.280402] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf840
[ 110.280549] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cfd80
[ 110.280698] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a7540
[ 110.280851] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf600
[ 110.281013] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf480
[ 110.281167] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10000
[ 110.281316] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10180
[ 110.281462] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10480
[ 110.281611] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10600
[ 110.281762] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10540
[ 110.281913] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d5ef4840
[ 110.282063] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d5ef4d80
[ 110.282208] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d5ef4f00
[ 110.282359] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d5ef4780
[ 110.282505] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a6540
[ 110.282662] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a6000
[ 110.282810] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a6180
[ 110.282961] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a6600
[ 110.283112] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a66c0
[ 110.283262] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf900
[ 110.283411] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf300
[ 110.283562] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf3c0
[ 110.283711] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cfc00
[ 110.283879] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf780
[ 110.284121] usb 1-2: fallback to eeprom programmed regulatory settings
[ 110.284122] ath: EEPROM regdomain: 0x37
[ 110.284122] ath: EEPROM indicates we should expect a direct regpair map
[ 110.284123] ath: Country alpha2 being used: AW
[ 110.284124] ath: Regpair used: 0x37
[ 110.312683] usb 1-2 wlx24f5a273d251: renamed from wlan0
[ 111.820827] usb 1-2: USB disconnect, device number 3
[ 111.871599] usb 1-2: usb free resources lpipe 0 hpipe 0xc0008300 urbs 32 avail 32
[ 111.871605] usb 1-2: usb free resources lpipe 1 hpipe 0xc0010300 urbs 32 avail 32
[ 111.871610] usb 1-2: usb free resources lpipe 2 hpipe 0xc0018300 urbs 32 avail 32
[ 111.871614] usb 1-2: usb free resources lpipe 3 hpipe 0xc0020300 urbs 32 avail 32
[ 111.871618] usb 1-2: usb free resources lpipe 4 hpipe 0xc0408380 urbs 32 avail 32
[ 111.871623] usb 1-2: usb free resources lpipe 5 hpipe 0xc0410380 urbs 32 avail 32
[ 111.871628] usb 1-2: usb free resources lpipe 6 hpipe 0xc0418380 urbs 32 avail 32
[ 111.871634] usb 1-2: usb free resources lpipe 7 hpipe 0xc0420380 urbs 32 avail 32
[-- Attachment #3: dmesg-usb-1-2.txt --]
[-- Type: text/plain, Size: 45614 bytes --]
[ 108.685119] usb 1-2: new high-speed USB device number 3 using xhci_hcd
[ 108.947519] usb 1-2: New USB device found, idVendor=13b1, idProduct=0042
[ 108.947522] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 108.947523] usb 1-2: Product: USBWLAN
[ 108.947524] usb 1-2: Manufacturer: Qualcomm Atheros
[ 108.947525] usb 1-2: SerialNumber: 12345678
[ 109.066597] usb 1-2: usb new func vendor 0x13b1 product 0x0042
[ 109.066600] usb 1-2: usb setting up pipes using interface
[ 109.066602] usb 1-2: usb rx bulk ep 0x81 maxpktsz 512
[ 109.066607] usb 1-2: usb alloc resources lpipe 4 hpipe 0xc0408380 urbs 32
[ 109.066608] usb 1-2: usb rx bulk ep 0x82 maxpktsz 512
[ 109.066612] usb 1-2: usb alloc resources lpipe 5 hpipe 0xc0410380 urbs 32
[ 109.066613] usb 1-2: usb rx bulk ep 0x83 maxpktsz 512
[ 109.066617] usb 1-2: usb alloc resources lpipe 6 hpipe 0xc0418380 urbs 32
[ 109.066618] usb 1-2: usb rx bulk ep 0x84 maxpktsz 512
[ 109.066621] usb 1-2: usb alloc resources lpipe 7 hpipe 0xc0420380 urbs 32
[ 109.066622] usb 1-2: usb tx bulk ep 0x01 maxpktsz 512
[ 109.066627] usb 1-2: usb alloc resources lpipe 0 hpipe 0xc0008300 urbs 32
[ 109.066628] usb 1-2: usb tx bulk ep 0x02 maxpktsz 512
[ 109.066631] usb 1-2: usb alloc resources lpipe 1 hpipe 0xc0010300 urbs 32
[ 109.066632] usb 1-2: usb tx bulk ep 0x03 maxpktsz 512
[ 109.066636] usb 1-2: usb alloc resources lpipe 2 hpipe 0xc0018300 urbs 32
[ 109.066638] usb 1-2: usb tx bulk ep 0x04 maxpktsz 512
[ 109.066641] usb 1-2: usb alloc resources lpipe 3 hpipe 0xc0020300 urbs 32
[ 109.066643] usb 1-2: WARNING: ath10k USB support is incomplete, don't expect anything to work!
[ 109.066647] usb 1-2: bmi get target info
[ 109.067242] usb 1-2: Hardware name qca9377 hw1.1 version 0x5020001
[ 109.076476] usb 1-2: Direct firmware load for ath10k/pre-cal-usb-1-2.bin failed with error -2
[ 109.076479] usb 1-2: boot fw request 'ath10k/pre-cal-usb-1-2.bin': -2
[ 109.076491] usb 1-2: Direct firmware load for ath10k/cal-usb-1-2.bin failed with error -2
[ 109.076493] usb 1-2: boot fw request 'ath10k/cal-usb-1-2.bin': -2
[ 109.076494] usb 1-2: trying fw api 6
[ 109.077322] usb 1-2: Direct firmware load for ath10k/QCA9377/hw1.0/firmware-usb-6.bin failed with error -2
[ 109.077325] usb 1-2: boot fw request 'ath10k/QCA9377/hw1.0/firmware-usb-6.bin': -2
[ 109.077326] usb 1-2: trying fw api 5
[ 109.083351] usb 1-2: boot fw request 'ath10k/QCA9377/hw1.0/firmware-usb-5.bin': 0
[ 109.083353] usb 1-2: found fw version CNSS.TF.1.0-00267-QCATFSWPZ-1
[ 109.083354] usb 1-2: found fw timestamp 1502520305
[ 109.083356] usb 1-2: found otp image ie (23749 B)
[ 109.083357] usb 1-2: found fw image ie (582052 B)
[ 109.083358] usb 1-2: found firmware features ie (1 B)
[ 109.083359] usb 1-2: Enabling feature bit: 7
[ 109.083360] usb 1-2: features
[ 109.083361] usb 1-2: 00000000: 80 00 00 00 00 00 00 00 ........
[ 109.083362] usb 1-2: found fw ie wmi op version 4
[ 109.083363] usb 1-2: found fw ie htt op version 3
[ 109.083364] usb 1-2: using fw api 5
[ 109.083367] usb 1-2: qca9377 hw1.1 target 0x05020001 chip_id 0x00000000 sub 0000:0000
[ 109.083368] usb 1-2: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 0
[ 109.083718] usb 1-2: firmware ver CNSS.TF.1.0-00267-QCATFSWPZ-1 api 5 features ignore-otp crc32 d6b81b3c
[ 109.083720] usb 1-2: boot did not find a pre calibration file, try DT next: -2
[ 109.083721] usb 1-2: unable to load pre cal data from DT: -2
[ 109.083722] usb 1-2: could not load pre cal data: -2
[ 109.083723] usb 1-2: boot upload otp to 0x1234 len 23749 for board id
[ 109.083725] usb 1-2: bmi fast download address 0x1234 buffer 0xffffa68fc0d7a048 length 23749
[ 109.083726] usb 1-2: bmi lz stream start address 0x1234
[ 109.084172] usb 1-2: bmi lz data buffer 0xffffa68fc0d7a048 length 23748
[ 109.119415] usb 1-2: bmi lz data buffer 0xffffa68fc0967ddc length 4
[ 109.119599] usb 1-2: bmi lz stream start address 0x0
[ 109.119776] usb 1-2: bmi execute address 0x1234 param 0x10
[ 109.120255] usb 1-2: bmi execute result 0x1
[ 109.120257] usb 1-2: boot get otp board id result 0x00000001 board_id 0 chip_id 0
[ 109.120259] usb 1-2: board id does not exist in otp, ignore it
[ 109.120278] usb 1-2: bdf variant name not set.
[ 109.120281] usb 1-2: boot using board name 'bus=usb,vendor=13b1,device=0042,subsystem-vendor=0000,subsystem-device=0000'
[ 109.129067] usb 1-2: boot fw request 'ath10k/QCA9377/hw1.0/board-2.bin': 0
[ 109.129070] usb 1-2: board name
[ 109.129072] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129074] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129075] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129077] usb 1-2: 00000030: 3d 31 36 39 63 2c 73 75 62 73 79 73 74 65 6d 2d =169c,subsystem-
[ 109.129078] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 36 35 device=3365
[ 109.129080] usb 1-2: board name
[ 109.129082] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129083] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129085] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129087] usb 1-2: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 74 65 6d 2d =168c,subsystem-
[ 109.129088] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 34 66 device=334f
[ 109.129091] usb 1-2: board name
[ 109.129093] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129095] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129096] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129098] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129100] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 32 62 device=412b
[ 109.129101] usb 1-2: board name
[ 109.129103] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129105] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129106] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129108] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129110] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 32 63 device=412c
[ 109.129111] usb 1-2: board name
[ 109.129113] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129115] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129116] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129118] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129120] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 32 64 device=412d
[ 109.129121] usb 1-2: board name
[ 109.129123] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129125] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129127] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129128] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129130] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 32 65 device=412e
[ 109.129132] usb 1-2: board name
[ 109.129134] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129135] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129137] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129139] usb 1-2: 00000030: 3d 31 34 34 64 2c 73 75 62 73 79 73 74 65 6d 2d =144d,subsystem-
[ 109.129141] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 33 33 device=4133
[ 109.129142] usb 1-2: board name
[ 109.129144] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129146] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129148] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129149] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129151] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 33 31 device=2231
[ 109.129152] usb 1-2: board name
[ 109.129154] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129156] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129158] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129159] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129161] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 62 33 31 device=2b31
[ 109.129162] usb 1-2: board name
[ 109.129164] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129165] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129168] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129170] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129171] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 63 33 31 device=2c31
[ 109.129173] usb 1-2: board name
[ 109.129175] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129177] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129178] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129180] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129183] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 64 33 31 device=2d31
[ 109.129184] usb 1-2: board name
[ 109.129185] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129186] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129187] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129188] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129189] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 66 33 31 device=2f31
[ 109.129191] usb 1-2: board name
[ 109.129192] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129193] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129194] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129195] usb 1-2: 00000030: 3d 31 34 34 66 2c 73 75 62 73 79 73 74 65 6d 2d =144f,subsystem-
[ 109.129196] usb 1-2: 00000040: 64 65 76 69 63 65 3d 37 31 34 35 device=7145
[ 109.129197] usb 1-2: board name
[ 109.129199] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129200] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129202] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129204] usb 1-2: 00000030: 3d 31 30 35 62 2c 73 75 62 73 79 73 74 65 6d 2d =105b,subsystem-
[ 109.129205] usb 1-2: 00000040: 64 65 76 69 63 65 3d 65 30 39 61 device=e09a
[ 109.129206] usb 1-2: board name
[ 109.129207] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129208] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129210] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129211] usb 1-2: 00000030: 3d 31 31 61 64 2c 73 75 62 73 79 73 74 65 6d 2d =11ad,subsystem-
[ 109.129212] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 38 30 36 device=0806
[ 109.129213] usb 1-2: board name
[ 109.129214] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129215] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129217] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129219] usb 1-2: 00000030: 3d 31 31 61 64 2c 73 75 62 73 79 73 74 65 6d 2d =11ad,subsystem-
[ 109.129220] usb 1-2: 00000040: 64 65 76 69 63 65 3d 31 38 30 36 device=1806
[ 109.129222] usb 1-2: board name
[ 109.129224] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129225] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129226] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129228] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129229] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 32 33 35 device=4235
[ 109.129230] usb 1-2: board name
[ 109.129231] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129232] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129233] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129234] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129235] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 33 33 35 device=4335
[ 109.129236] usb 1-2: board name
[ 109.129238] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129239] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129240] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129241] usb 1-2: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 74 65 6d 2d =168c,subsystem-
[ 109.129243] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 36 35 device=3365
[ 109.129245] usb 1-2: board name
[ 109.129247] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129248] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129249] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129250] usb 1-2: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 74 65 6d 2d =168c,subsystem-
[ 109.129252] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 36 39 device=3369
[ 109.129253] usb 1-2: board name
[ 109.129254] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129255] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129256] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129258] usb 1-2: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 74 65 6d 2d =168c,subsystem-
[ 109.129259] usb 1-2: 00000040: 64 65 76 69 63 65 3d 33 33 36 38 device=3368
[ 109.129261] usb 1-2: board name
[ 109.129263] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129264] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129266] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129267] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129269] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 33 61 device=223a
[ 109.129270] usb 1-2: board name
[ 109.129271] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129272] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129273] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129274] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129275] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 33 62 device=223b
[ 109.129276] usb 1-2: board name
[ 109.129278] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129279] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129280] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129281] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129282] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 33 63 device=223c
[ 109.129283] usb 1-2: board name
[ 109.129285] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129286] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129288] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129290] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129291] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 32 35 31 device=2251
[ 109.129292] usb 1-2: board name
[ 109.129293] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129294] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129295] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129296] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129297] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 62 35 31 device=2b51
[ 109.129298] usb 1-2: board name
[ 109.129299] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129301] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129302] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129304] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129306] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 63 35 31 device=2c51
[ 109.129308] usb 1-2: board name
[ 109.129310] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129311] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129312] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129313] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129314] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 61 35 31 device=2a51
[ 109.129315] usb 1-2: board name
[ 109.129316] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129318] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129319] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129320] usb 1-2: 00000030: 3d 31 34 34 66 2c 73 75 62 73 79 73 74 65 6d 2d =144f,subsystem-
[ 109.129321] usb 1-2: 00000040: 64 65 76 69 63 65 3d 37 31 34 32 device=7142
[ 109.129322] usb 1-2: board name
[ 109.129323] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129325] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129326] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129328] usb 1-2: 00000030: 3d 31 31 61 64 2c 73 75 62 73 79 73 74 65 6d 2d =11ad,subsystem-
[ 109.129329] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 35 30 37 device=0507
[ 109.129331] usb 1-2: board name
[ 109.129332] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129333] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129334] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129335] usb 1-2: 00000030: 3d 31 61 33 62 2c 73 75 62 73 79 73 74 65 6d 2d =1a3b,subsystem-
[ 109.129336] usb 1-2: 00000040: 64 65 76 69 63 65 3d 32 35 31 30 device=2510
[ 109.129338] usb 1-2: board name
[ 109.129339] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129340] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129341] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129342] usb 1-2: 00000030: 3d 31 31 61 64 2c 73 75 62 73 79 73 74 65 6d 2d =11ad,subsystem-
[ 109.129344] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 38 61 36 device=08a6
[ 109.129345] usb 1-2: board name
[ 109.129347] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129348] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129350] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129351] usb 1-2: 00000030: 3d 31 30 35 62 2c 73 75 62 73 79 73 74 65 6d 2d =105b,subsystem-
[ 109.129352] usb 1-2: 00000040: 64 65 76 69 63 65 3d 65 30 61 31 device=e0a1
[ 109.129353] usb 1-2: board name
[ 109.129354] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129355] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129357] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129358] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129359] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 30 33 35 device=4035
[ 109.129360] usb 1-2: board name
[ 109.129361] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129362] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129364] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129365] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129366] usb 1-2: 00000040: 64 65 76 69 63 65 3d 34 31 33 35 device=4135
[ 109.129396] usb 1-2: board name
[ 109.129399] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129401] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129402] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129404] usb 1-2: 00000030: 3d 31 37 61 61 2c 73 75 62 73 79 73 74 65 6d 2d =17aa,subsystem-
[ 109.129405] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 39 30 31 device=0901
[ 109.129407] usb 1-2: board name
[ 109.129408] usb 1-2: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 109.129410] usb 1-2: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 68c,device=0042,
[ 109.129411] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129413] usb 1-2: 00000030: 3d 31 30 32 38 2c 73 75 62 73 79 73 74 65 6d 2d =1028,subsystem-
[ 109.129415] usb 1-2: 00000040: 64 65 76 69 63 65 3d 31 38 31 30 device=1810
[ 109.129417] usb 1-2: board name
[ 109.129419] usb 1-2: 00000000: 62 75 73 3d 75 73 62 2c 76 65 6e 64 6f 72 3d 31 bus=usb,vendor=1
[ 109.129421] usb 1-2: 00000010: 33 62 31 2c 64 65 76 69 63 65 3d 30 30 34 32 2c 3b1,device=0042,
[ 109.129422] usb 1-2: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 109.129425] usb 1-2: 00000030: 3d 30 30 30 30 2c 73 75 62 73 79 73 74 65 6d 2d =0000,subsystem-
[ 109.129426] usb 1-2: 00000040: 64 65 76 69 63 65 3d 30 30 30 30 device=0000
[ 109.129428] usb 1-2: boot found match for name 'bus=usb,vendor=13b1,device=0042,subsystem-vendor=0000,subsystem-device=0000'
[ 109.129429] usb 1-2: boot found board data for 'bus=usb,vendor=13b1,device=0042,subsystem-vendor=0000,subsystem-device=0000'
[ 109.129431] usb 1-2: using board api 2
[ 109.129620] usb 1-2: board_file api 2 bmi_id N/A crc32 22a1f6f4
[ 109.129623] usb 1-2: bmi start
[ 109.129625] usb 1-2: bmi read soc register 0x00000b2c
[ 109.130397] usb 1-2: bmi read soc register value 0x00000080
[ 109.130399] usb 1-2: bmi read soc register 0x00000af4
[ 109.131056] usb 1-2: bmi read soc register value 0x0006aaa8
[ 109.131057] usb 1-2: bmi write soc register 0x00000af4 val 0x0006aaa8
[ 109.131292] usb 1-2: bmi read soc register 0x00001018
[ 109.131662] usb 1-2: bmi read soc register value 0x00000160
[ 109.131664] usb 1-2: bmi write soc register 0x00001018 val 0x00000160
[ 109.131841] usb 1-2: bmi read soc register 0x00000914
[ 109.132233] usb 1-2: bmi read soc register value 0x00000001
[ 109.132235] usb 1-2: bmi write soc register 0x00000914 val 0x00000001
[ 109.132440] usb 1-2: bmi write address 0x404028 length 4
[ 109.132640] usb 1-2: bmi read soc register 0x00001014
[ 109.133031] usb 1-2: bmi read soc register value 0x0000000e
[ 109.133032] usb 1-2: bmi write soc register 0x00001014 val 0x0004000e
[ 109.133226] usb 1-2: bmi read soc register 0x00001244
[ 109.133596] usb 1-2: bmi read soc register value 0x00000002
[ 109.133597] usb 1-2: bmi read soc register 0x00001014
[ 109.133959] usb 1-2: bmi read soc register value 0x0004000e
[ 109.133960] usb 1-2: bmi write soc register 0x00001014 val 0x0004000e
[ 109.134142] usb 1-2: bmi read soc register 0x00001244
[ 109.134501] usb 1-2: bmi read soc register value 0x00000002
[ 109.134503] usb 1-2: bmi read soc register 0x00000820
[ 109.134858] usb 1-2: bmi read soc register value 0x00000001
[ 109.134859] usb 1-2: bmi write soc register 0x00000820 val 0x00000001
[ 109.135047] usb 1-2: bmi read soc register 0x00001014
[ 109.135407] usb 1-2: bmi read soc register value 0x0004000e
[ 109.135408] usb 1-2: bmi write soc register 0x00001014 val 0x0000000e
[ 109.135594] usb 1-2: bmi write address 0x404020 length 4
[ 109.135777] usb 1-2: bmi write address 0x404024 length 4
[ 109.135969] usb 1-2: bmi enable pll ret 0
[ 109.135971] usb 1-2: bmi write address 0x400800 length 4
[ 109.136655] usb 1-2: bmi read address 0x400810 length 4
[ 109.137040] usb 1-2: bmi write address 0x400810 length 4
[ 109.137235] usb 1-2: bmi write address 0x400844 length 4
[ 109.137436] usb 1-2: bmi write address 0x400904 length 4
[ 109.137636] usb 1-2: bmi write address 0x4008bc length 4
[ 109.137833] usb 1-2: boot did not find a pre calibration file, try DT next: -2
[ 109.137834] usb 1-2: unable to load pre cal data from DT: -2
[ 109.137835] usb 1-2: failed to load pre cal data: -2
[ 109.137836] usb 1-2: pre cal download procedure failed, try cal file: -2
[ 109.137837] usb 1-2: boot did not find a calibration file, try DT next: -2
[ 109.137838] usb 1-2: boot did not find DT entry, try target EEPROM next: -2
[ 109.137839] usb 1-2: boot did not find target EEPROM entry, try OTP next: -95
[ 109.137841] usb 1-2: bmi read address 0x4008ac length 4
[ 109.139278] usb 1-2: boot push board extended data addr 0x0
[ 109.139280] usb 1-2: bmi read address 0x400854 length 4
[ 109.139843] usb 1-2: bmi write address 0x401fc0 length 8124
[ 109.152458] usb 1-2: bmi write address 0x400858 length 4
[ 109.152646] usb 1-2: boot upload otp to 0x1234 len 23749
[ 109.152647] usb 1-2: bmi fast download address 0x1234 buffer 0xffffa68fc0d7a048 length 23749
[ 109.152648] usb 1-2: bmi lz stream start address 0x1234
[ 109.152834] usb 1-2: bmi lz data buffer 0xffffa68fc0d7a048 length 23748
[ 109.190512] usb 1-2: bmi lz data buffer 0xffffa68fc0967d8c length 4
[ 109.190752] usb 1-2: bmi lz stream start address 0x0
[ 109.191010] usb 1-2: bmi execute address 0x1234 param 0x0
[ 109.192025] usb 1-2: bmi execute result 0x3
[ 109.192026] usb 1-2: boot otp execute result 3
[ 109.192028] usb 1-2: boot using calibration mode otp
[ 109.192029] usb 1-2: boot uploading firmware image ffffa68fc0d7fd18 len 582052
[ 109.192031] usb 1-2: bmi fast download address 0x1234 buffer 0xffffa68fc0d7fd18 length 582052
[ 109.192032] usb 1-2: bmi lz stream start address 0x1234
[ 109.192281] usb 1-2: bmi lz data buffer 0xffffa68fc0d7fd18 length 582052
[ 110.253443] usb 1-2: bmi lz stream start address 0x0
[ 110.253696] usb 1-2: bmi write address 0x400814 length 4
[ 110.253948] usb 1-2: boot htc service 'Control' ul pipe 0 dl pipe 5 eid 0 ready
[ 110.253951] usb 1-2: boot htc service 'Control' eid 0 TX flow control disabled
[ 110.253953] usb 1-2: bmi done
[ 110.254202] usb 1-2: htt tx max num pending tx 1056
[ 110.254218] usb 1-2: htt rx ring size 2048 fill_level 1023
[ 110.254225] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d63ab700
[ 110.254241] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d4b16900
[ 110.254252] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798543600
[ 110.254262] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5020900
[ 110.254272] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5043300
[ 110.254286] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d944b700
[ 110.254303] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fc400
[ 110.254316] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d944bc00
[ 110.254329] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fce00
[ 110.254343] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fc900
[ 110.254355] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4f00
[ 110.254370] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55f2d00
[ 110.254383] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4600
[ 110.254397] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4d00
[ 110.254410] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4b00
[ 110.254422] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5c00
[ 110.254433] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5200
[ 110.254446] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5f00
[ 110.254460] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5028f00
[ 110.254471] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5028200
[ 110.254482] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d8b6b400
[ 110.254494] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d503a600
[ 110.254505] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d503a000
[ 110.254517] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d50ac700
[ 110.254533] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55f0200
[ 110.254561] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5020800
[ 110.254576] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d7554e00
[ 110.254587] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5023100
[ 110.254599] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fcd00
[ 110.254611] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55cd800
[ 110.254623] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d501db00
[ 110.254634] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d9452900
[ 110.259198] usb 1-2: usb recv pipe 5 stat 0 len 20 urb 0xffff99e7d7c10540
[ 110.259208] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d50bc000
[ 110.263917] usb 1-2: Target ready! transmit resources: 3 size:1792
[ 110.263920] usb 1-2: Extended ready message. RX bundle size: 0
[ 110.263922] usb 1-2: boot htc service HTT Data does not allocate target credits
[ 110.263926] usb 1-2: ath10k_htc_build_tx_ctrl_skb: skb ffff99e7d63ab700
[ 110.264168] usb 1-2: usb recv pipe 5 stat 0 len 20 urb 0xffff99e7d7c10600
[ 110.264175] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798442200
[ 110.264233] usb 1-2: ath10k_htc_notify_tx_completion: ep 0 skb ffff99e7d63ab700
[ 110.264244] usb 1-2: HTC Service HTT Data connect response: status: 0x0, assigned ep: 0x1
[ 110.264247] usb 1-2: boot htc service 'HTT Data' ul pipe 1 dl pipe 5 eid 1 ready
[ 110.264249] usb 1-2: boot htc service 'HTT Data' eid 1 TX flow control disabled
[ 110.264253] usb 1-2: ath10k_htc_build_tx_ctrl_skb: skb ffff99e7d4b16900
[ 110.264546] usb 1-2: usb recv pipe 5 stat 0 len 20 urb 0xffff99e7d7c10480
[ 110.264553] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d63ab700
[ 110.264607] usb 1-2: ath10k_htc_notify_tx_completion: ep 0 skb ffff99e7d4b16900
[ 110.264616] usb 1-2: HTC Service WMI connect response: status: 0x0, assigned ep: 0x2
[ 110.264619] usb 1-2: boot htc service 'WMI' ul pipe 0 dl pipe 5 eid 2 ready
[ 110.264622] usb 1-2: ath10k_htc_build_tx_ctrl_skb: skb ffff99e798543600
[ 110.264624] usb 1-2: HTC is using TX credit flow control
[ 110.264939] usb 1-2: usb recv pipe 5 stat 0 len 12 urb 0xffff99e7d7c10180
[ 110.264944] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e793a4b700
[ 110.265001] usb 1-2: usb recv pipe 5 stat 0 len 296 urb 0xffff99e7d7c10000
[ 110.265010] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798442a00
[ 110.265056] usb 1-2: ath10k_htc_notify_tx_completion: ep 0 skb ffff99e798543600
[ 110.265062] usb 1-2: htt rx, msg_type: 0xF
[ 110.265139] usb 1-2: wmi tlv abi 0x01000000 ?= 0x01000000, 0x5f414351 ?= 0x5f414351, 0x00004c4d ?= 0x00004c4d, 0x00000000 ?= 0x00000000, 0x00000000 ?= 0x00000000
[ 110.265145] usb 1-2: wmi svc: 00000000: 0d 00 00 00 07 00 00 00 0f 00 00 00 03 00 00 00 ................
[ 110.265148] usb 1-2: wmi svc: 00000010: 0f 00 00 00 0f 00 00 00 0b 00 00 00 0f 00 00 00 ................
[ 110.265150] usb 1-2: wmi svc: 00000020: 0b 00 00 00 0b 00 00 00 04 00 00 00 0a 00 00 00 ................
[ 110.265153] usb 1-2: wmi svc: 00000030: 01 00 00 00 00 00 00 00 08 00 00 00 00 00 00 00 ................
[ 110.265155] usb 1-2: wmi svc: 00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 110.265157] usb 1-2: wmi svc: 00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 110.265159] usb 1-2: wmi svc: 00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 110.265162] usb 1-2: wmi svc: 00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 110.265167] usb 1-2: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000085b vht_cap 0x339011b2 sw_ver0 0x01000000 sw_ver1 0x0000003d fw_build 0x10358701 phy_capab 0x00000003 num_rf_chains 0x00000001 eeprom_rd 0x00000037 num_mem_reqs 0x00000000
[ 110.265210] usb 1-2: firmware CNSS.TF.1.0-00267-QCATFSWPZ-1 booted
[ 110.265214] usb 1-2: wmi tlv init
[ 110.265217] usb 1-2: htc ep 2 consumed 1 credits (total 2)
[ 110.265514] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e7d9477f00
[ 110.272012] usb 1-2: usb recv pipe 5 stat 0 len 1500 urb 0xffff99e7d77cf480
[ 110.272023] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5681e00
[ 110.272084] usb 1-2: wmi event debug mesg len 1488
[ 110.273351] usb 1-2: usb recv pipe 5 stat 0 len 52 urb 0xffff99e7d77cf600
[ 110.273363] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d4b16c00
[ 110.273382] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf6c0
[ 110.273390] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d4b16800
[ 110.273451] usb 1-2: wmi event ready sw_version 16777216 abi_version 61 mac_addr 24:f5:a2:73:d2:51 status 0
[ 110.273458] usb 1-2: htc ep 2 got 1 credits (total 3)
[ 110.273466] usb 1-2: wmi tlv vdev create
[ 110.273469] usb 1-2: htc ep 2 consumed 1 credits (total 2)
[ 110.273483] usb 1-2: wmi tlv vdev delete
[ 110.273486] usb 1-2: htc ep 2 consumed 1 credits (total 1)
[ 110.273497] usb 1-2: wmi tlv echo value 0x0ba991e9
[ 110.273499] usb 1-2: htc ep 2 consumed 1 credits (total 0)
[ 110.273793] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e7d944bc00
[ 110.273798] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e7d55fc400
[ 110.273800] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e7d6bc6200
[ 110.274074] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cfd80
[ 110.274084] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d944bc00
[ 110.274200] usb 1-2: htc ep 2 got 1 credits (total 1)
[ 110.274277] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf840
[ 110.274287] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55fce00
[ 110.274304] usb 1-2: usb recv pipe 5 stat 0 len 20 urb 0xffff99e7d77cff00
[ 110.274308] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e793a4ae00
[ 110.274325] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf9c0
[ 110.274331] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d5594700
[ 110.274372] usb 1-2: htc ep 2 got 1 credits (total 2)
[ 110.274377] usb 1-2: wmi event echo value 0x0ba991e9
[ 110.274382] usb 1-2: htc ep 2 got 1 credits (total 3)
[ 110.274965] usb 1-2: ath10k_htc_notify_tx_completion: ep 1 skb ffff99e798715200
[ 110.275060] usb 1-2: usb recv pipe 5 stat 0 len 12 urb 0xffff99e7d77cf000
[ 110.275068] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715200
[ 110.275126] usb 1-2: htt rx, msg_type: 0x0
[ 110.275134] usb 1-2: htt target version 3.1
[ 110.275149] usb 1-2: htt h2t aggr cfg msg amsdu 3 ampdu 64
[ 110.275159] usb 1-2: wmi tlv pktlog disable
[ 110.275162] usb 1-2: htc ep 2 consumed 1 credits (total 2)
[ 110.275174] usb 1-2: htt-ver 3.1 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[ 110.275486] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e798715f00
[ 110.275490] usb 1-2: ath10k_htc_notify_tx_completion: ep 1 skb ffff99e7d55d4600
[ 110.275493] usb 1-2: ath10k_htc_notify_tx_completion: ep 1 skb ffff99e798715b00
[ 110.275561] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf540
[ 110.275599] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715b00
[ 110.275711] usb 1-2: htc ep 2 got 1 credits (total 3)
[ 110.277321] usb 1-2: wmi tlv pktlog disable
[ 110.277325] usb 1-2: htc ep 2 consumed 1 credits (total 2)
[ 110.277340] usb 1-2: wmi tlv pdev suspend
[ 110.277343] usb 1-2: htc ep 2 consumed 1 credits (total 1)
[ 110.277644] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e798715c00
[ 110.277648] usb 1-2: ath10k_htc_notify_tx_completion: ep 2 skb ffff99e798715500
[ 110.277785] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf0c0
[ 110.277796] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715500
[ 110.277818] usb 1-2: usb recv pipe 5 stat 0 len 1336 urb 0xffff99e7d77cfb40
[ 110.277824] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715c00
[ 110.277841] usb 1-2: usb recv pipe 5 stat 0 len 16 urb 0xffff99e7d77cf240
[ 110.277849] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798716600
[ 110.277861] usb 1-2: usb recv pipe 5 stat 0 len 12 urb 0xffff99e7d77cf180
[ 110.277866] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798716900
[ 110.277914] usb 1-2: htc ep 2 got 1 credits (total 2)
[ 110.277919] usb 1-2: wmi event debug mesg len 1324
[ 110.277922] usb 1-2: htc ep 2 got 1 credits (total 3)
[ 110.277925] usb 1-2: boot suspend complete
[ 110.278229] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf240
[ 110.278412] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cfb40
[ 110.278595] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf0c0
[ 110.278778] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf540
[ 110.278927] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf9c0
[ 110.279078] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7da444480
[ 110.279145] usb 1-2: usb recv pipe 5 stat 0 len 244 urb 0xffff99e7d77cfcc0
[ 110.279149] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715200
[ 110.279152] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798715c00
[ 110.279153] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5200
[ 110.279155] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d57c5c00
[ 110.279157] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e7d55d4b00
[ 110.279159] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798716300
[ 110.279161] usb 1-2: usb bulk recv submit 5 0xc0410380 ep 0x82 len 4096 buf 0xffff99e798716e00
[ 110.279167] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cff00
[ 110.279195] usb 1-2: zero length frame received, firmware crashed?
[ 110.279315] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf000
[ 110.279466] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf240
[ 110.279614] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cfb40
[ 110.279767] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf0c0
[ 110.279948] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf540
[ 110.280106] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf9c0
[ 110.280254] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7da444480
[ 110.280402] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf840
[ 110.280549] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cfd80
[ 110.280698] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a7540
[ 110.280851] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf600
[ 110.281013] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf480
[ 110.281167] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10000
[ 110.281316] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10180
[ 110.281462] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10480
[ 110.281611] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10600
[ 110.281762] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d7c10540
[ 110.281913] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d5ef4840
[ 110.282063] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d5ef4d80
[ 110.282208] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d5ef4f00
[ 110.282359] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d5ef4780
[ 110.282505] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a6540
[ 110.282662] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a6000
[ 110.282810] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a6180
[ 110.282961] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a6600
[ 110.283112] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d55a66c0
[ 110.283262] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf900
[ 110.283411] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf300
[ 110.283562] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf3c0
[ 110.283711] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cfc00
[ 110.283879] usb 1-2: usb recv pipe 5 stat -2 len 0 urb 0xffff99e7d77cf780
[ 110.284121] usb 1-2: fallback to eeprom programmed regulatory settings
[ 110.312683] usb 1-2 wlx24f5a273d251: renamed from wlan0
[ 111.820827] usb 1-2: USB disconnect, device number 3
[ 111.871599] usb 1-2: usb free resources lpipe 0 hpipe 0xc0008300 urbs 32 avail 32
[ 111.871605] usb 1-2: usb free resources lpipe 1 hpipe 0xc0010300 urbs 32 avail 32
[ 111.871610] usb 1-2: usb free resources lpipe 2 hpipe 0xc0018300 urbs 32 avail 32
[ 111.871614] usb 1-2: usb free resources lpipe 3 hpipe 0xc0020300 urbs 32 avail 32
[ 111.871618] usb 1-2: usb free resources lpipe 4 hpipe 0xc0408380 urbs 32 avail 32
[ 111.871623] usb 1-2: usb free resources lpipe 5 hpipe 0xc0410380 urbs 32 avail 32
[ 111.871628] usb 1-2: usb free resources lpipe 6 hpipe 0xc0418380 urbs 32 avail 32
[ 111.871634] usb 1-2: usb free resources lpipe 7 hpipe 0xc0420380 urbs 32 avail 32
[-- Attachment #4: Type: text/plain, Size: 146 bytes --]
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2018-09-07 7:40 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <MW2PR12MB2458671FF0444136A06CE26BF8000@MW2PR12MB2458.namprd12.prod.outlook.com>
2018-09-07 7:39 ` [ath10k USB QCA9377] Driver fails to initialize Linksys device Vincent Guenat
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.