* Re: USB suspend issue with 2.6.38-rc2 -- still there in RC4-g795abaf
[not found] <m31v3abf1k.fsf@x201s.gr8dns.org>
@ 2011-02-14 20:55 ` Alan Stern
0 siblings, 0 replies; 4+ messages in thread
From: Alan Stern @ 2011-02-14 20:55 UTC (permalink / raw)
To: Dirk Hohndel; +Cc: Linux PM List, Linux USB List, Linus Torvalds
On Mon, 14 Feb 2011, Dirk Hohndel wrote:
> > It might help to see the dmesg output rather than the system log file.
> > Include everything going back to the boot.
>
> Here's the latest, with the latest kernel from Linus: 2.6.38-rc4-00178-g795abaf
> which includes the commit that you mentioned bf3d7d40e42a85ca73a34e1385ff34f092a384eb
>
> I did a successfull suspend / resume while the system was in the docking
> station - that's around seconds 42-44 in the dmesg output.
>
> Next I undock and do another suspend attempt - starts around second
> 57. This one failed again, but now we have much more information from
> the dmesg output - attached all the way from reboot.
>
> > > 1-1 appears to be my built-in root hub.
> >
> > No, the root hub is usb1. 1-1 is the device plugged into port 1 of the
> > root hub. If you have a debugfs filesystem mounted, you can see the
> > device list in /sys/kernel/debug/usb/devices.
>
> I'm attaching that as well :-)
>
> Let me know what else I should send / try.
Okay, this is great. The log shows you have a Broadcom Bluetooth
device that got disconnected right at the same time each suspend
started. Did you unplug it by hand or were the disconnects triggered
by the hardware somehow?
At any rate, the close timing between the disconnect and the suspend
caused a new race to show up, one I haven't come across before. Even
though the Bluetooth device's USB port was disabled, the device was not
yet unregistered. The hub driver saw the device structure was still
present and refused to suspend, thinking there was an unsuspended child
device attached.
I can't recall having seen this particular failure path (an attempt to
suspend a hub while one of its attached devices is still active) in
years, if ever. Hence the easiest way to solve the problem is to
remove the check. Hopefully the patch below will fix your problem.
Alan Stern
P.S.: Contrary to Linus's earlier suggestion, it's not a good idea to
remove _all_ checks for failures during suspend. The same code is used
for both system sleep and runtime PM, and we definitely _do_ want to
catch failures during runtime suspend.
Index: usb-2.6/drivers/usb/core/hub.c
===================================================================
--- usb-2.6.orig/drivers/usb/core/hub.c
+++ usb-2.6/drivers/usb/core/hub.c
@@ -2457,21 +2457,6 @@ int usb_port_resume(struct usb_device *u
static int hub_suspend(struct usb_interface *intf, pm_message_t msg)
{
struct usb_hub *hub = usb_get_intfdata (intf);
- struct usb_device *hdev = hub->hdev;
- unsigned port1;
-
- /* fail if children aren't already suspended */
- for (port1 = 1; port1 <= hdev->maxchild; port1++) {
- struct usb_device *udev;
-
- udev = hdev->children [port1-1];
- if (udev && udev->can_submit) {
- if (!(msg.event & PM_EVENT_AUTO))
- dev_dbg(&intf->dev, "port %d nyet suspended\n",
- port1);
- return -EBUSY;
- }
- }
dev_dbg(&intf->dev, "%s\n", __func__);
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: USB suspend issue with 2.6.38-rc2 -- still there in RC4-g795abaf
[not found] <m31v3a8i4j.fsf@x201s.gr8dns.org>
@ 2011-02-14 21:12 ` Alan Stern
0 siblings, 0 replies; 4+ messages in thread
From: Alan Stern @ 2011-02-14 21:12 UTC (permalink / raw)
To: Dirk Hohndel; +Cc: Linux PM List, Linux USB List, Linus Torvalds
On Mon, 14 Feb 2011, Dirk Hohndel wrote:
> On Mon, 14 Feb 2011 11:33:01 -0800, Linus Torvalds <torvalds@linux-foundation.org> wrote:
> > Does it suspend reliably if we just get rid of the crap that looks for errors?
>
> Yes. I tried all combinations I could think of. Docked. Undocked.
> Docking while suspended. Undocking while suspended. Did something like
> 20 suspend / resume cycles in a row. All works.
>
> I will continue to play with this but for now I consider this solved
>
> > As mentioned, there's no _point_ to looking at errors. Reacting to
> > errors in suspend can only make things worse, not better. If the
> > suspend of some device fails, then it fails. Big deal. Take the
> > machine down regardless.
> >
> > Trial patch attached. Untested. It may do nasty things to your pets.
>
> Pets didn't mind at all (but I kept them away from the machine, just in
> case)
>
> /D
>
>
> > drivers/usb/core/driver.c | 33 +++++++++------------------------
> > 1 files changed, 9 insertions(+), 24 deletions(-)
> >
> > diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c
> > index fca6172..e302189 100644
> > --- a/drivers/usb/core/driver.c
> > +++ b/drivers/usb/core/driver.c
> > @@ -1173,7 +1173,6 @@ done:
> > */
> > static int usb_suspend_both(struct usb_device *udev, pm_message_t msg)
> > {
> > - int status = 0;
> > int i = 0, n = 0;
> > struct usb_interface *intf;
> >
> > @@ -1186,36 +1185,22 @@ static int usb_suspend_both(struct usb_device *udev, pm_message_t msg)
> > n = udev->actconfig->desc.bNumInterfaces;
> > for (i = n - 1; i >= 0; --i) {
> > intf = udev->actconfig->interface[i];
> > - status = usb_suspend_interface(udev, intf, msg);
> > - if (status != 0)
> > - break;
> > + usb_suspend_interface(udev, intf, msg);
> > }
> > }
> > - if (status == 0)
> > - status = usb_suspend_device(udev, msg);
> > -
> > - /* If the suspend failed, resume interfaces that did get suspended */
> > - if (status != 0) {
> > - msg.event ^= (PM_EVENT_SUSPEND | PM_EVENT_RESUME);
> > - while (++i < n) {
> > - intf = udev->actconfig->interface[i];
> > - usb_resume_interface(udev, intf, msg, 0);
> > - }
> > + usb_suspend_device(udev, msg);
> >
> > - /* If the suspend succeeded then prevent any more URB submissions
> > - * and flush any outstanding URBs.
> > + /* Prevent any more URB submissions and flush any outstanding URBs.
> > */
> > - } else {
> > - udev->can_submit = 0;
> > - for (i = 0; i < 16; ++i) {
> > - usb_hcd_flush_endpoint(udev, udev->ep_out[i]);
> > - usb_hcd_flush_endpoint(udev, udev->ep_in[i]);
> > - }
> > + udev->can_submit = 0;
> > + for (i = 0; i < 16; ++i) {
> > + usb_hcd_flush_endpoint(udev, udev->ep_out[i]);
> > + usb_hcd_flush_endpoint(udev, udev->ep_in[i]);
> > }
> >
> > done:
> > - dev_vdbg(&udev->dev, "%s: status %d\n", __func__, status);
> > - return status;
> > + dev_vdbg(&udev->dev, "%s: suspend\n", __func__);
> > + return 0;
> > }
> >
> > /**
This doesn't differentiate between system sleep and runtime suspend;
the patch below is better. I'll submit it in addition to the change to
the hub driver. After all, other drivers may also fail during a sleep
transition.
Alan Stern
Index: usb-2.6/drivers/usb/core/driver.c
===================================================================
--- usb-2.6.orig/drivers/usb/core/driver.c
+++ usb-2.6/drivers/usb/core/driver.c
@@ -1187,6 +1187,10 @@ static int usb_suspend_both(struct usb_d
for (i = n - 1; i >= 0; --i) {
intf = udev->actconfig->interface[i];
status = usb_suspend_interface(udev, intf, msg);
+
+ /* Ignore errors during system sleep transitions */
+ if (!(msg.event & PM_EVENT_AUTO))
+ status = 0;
if (status != 0)
break;
}
@@ -1195,7 +1199,7 @@ static int usb_suspend_both(struct usb_d
status = usb_suspend_device(udev, msg);
/* If the suspend failed, resume interfaces that did get suspended */
- if (status != 0) {
+ if (status != 0 && (msg.event & PM_EVENT_AUTO)) {
msg.event ^= (PM_EVENT_SUSPEND | PM_EVENT_RESUME);
while (++i < n) {
intf = udev->actconfig->interface[i];
@@ -1303,7 +1307,9 @@ int usb_suspend(struct device *dev, pm_m
do_unbind_rebind(udev, DO_UNBIND);
choose_wakeup(udev, msg);
- return usb_suspend_both(udev, msg);
+ usb_suspend_both(udev, msg);
+
+ return 0; /* Allow system to go to sleep regardless of errors */
}
/* The device lock is held by the PM core */
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: USB suspend issue with 2.6.38-rc2 -- still there in RC4-g795abaf
[not found] ` <AANLkTik4e0UoMbtMUSsyym_y-Y-xcTzdJK26zzGk719f@mail.gmail.com>
@ 2011-02-14 20:40 ` Dirk Hohndel
0 siblings, 0 replies; 4+ messages in thread
From: Dirk Hohndel @ 2011-02-14 20:40 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Linux PM List, Linux USB List
On Mon, 14 Feb 2011 11:33:01 -0800, Linus Torvalds <torvalds@linux-foundation.org> wrote:
> Does it suspend reliably if we just get rid of the crap that looks for errors?
Yes. I tried all combinations I could think of. Docked. Undocked.
Docking while suspended. Undocking while suspended. Did something like
20 suspend / resume cycles in a row. All works.
I will continue to play with this but for now I consider this solved
> As mentioned, there's no _point_ to looking at errors. Reacting to
> errors in suspend can only make things worse, not better. If the
> suspend of some device fails, then it fails. Big deal. Take the
> machine down regardless.
>
> Trial patch attached. Untested. It may do nasty things to your pets.
Pets didn't mind at all (but I kept them away from the machine, just in
case)
/D
> drivers/usb/core/driver.c | 33 +++++++++------------------------
> 1 files changed, 9 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c
> index fca6172..e302189 100644
> --- a/drivers/usb/core/driver.c
> +++ b/drivers/usb/core/driver.c
> @@ -1173,7 +1173,6 @@ done:
> */
> static int usb_suspend_both(struct usb_device *udev, pm_message_t msg)
> {
> - int status = 0;
> int i = 0, n = 0;
> struct usb_interface *intf;
>
> @@ -1186,36 +1185,22 @@ static int usb_suspend_both(struct usb_device *udev, pm_message_t msg)
> n = udev->actconfig->desc.bNumInterfaces;
> for (i = n - 1; i >= 0; --i) {
> intf = udev->actconfig->interface[i];
> - status = usb_suspend_interface(udev, intf, msg);
> - if (status != 0)
> - break;
> + usb_suspend_interface(udev, intf, msg);
> }
> }
> - if (status == 0)
> - status = usb_suspend_device(udev, msg);
> -
> - /* If the suspend failed, resume interfaces that did get suspended */
> - if (status != 0) {
> - msg.event ^= (PM_EVENT_SUSPEND | PM_EVENT_RESUME);
> - while (++i < n) {
> - intf = udev->actconfig->interface[i];
> - usb_resume_interface(udev, intf, msg, 0);
> - }
> + usb_suspend_device(udev, msg);
>
> - /* If the suspend succeeded then prevent any more URB submissions
> - * and flush any outstanding URBs.
> + /* Prevent any more URB submissions and flush any outstanding URBs.
> */
> - } else {
> - udev->can_submit = 0;
> - for (i = 0; i < 16; ++i) {
> - usb_hcd_flush_endpoint(udev, udev->ep_out[i]);
> - usb_hcd_flush_endpoint(udev, udev->ep_in[i]);
> - }
> + udev->can_submit = 0;
> + for (i = 0; i < 16; ++i) {
> + usb_hcd_flush_endpoint(udev, udev->ep_out[i]);
> + usb_hcd_flush_endpoint(udev, udev->ep_in[i]);
> }
>
> done:
> - dev_vdbg(&udev->dev, "%s: status %d\n", __func__, status);
> - return status;
> + dev_vdbg(&udev->dev, "%s: suspend\n", __func__);
> + return 0;
> }
>
> /**
--
Dirk Hohndel
Intel Open Source Technology Center
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: USB suspend issue with 2.6.38-rc2 -- still there in RC4-g795abaf
[not found] <Pine.LNX.4.44L0.1101251021310.1867-100000@iolanthe.rowland.org>
@ 2011-02-14 19:18 ` Dirk Hohndel
[not found] ` <m38vxibfez.fsf@x201s.gr8dns.org>
1 sibling, 0 replies; 4+ messages in thread
From: Dirk Hohndel @ 2011-02-14 19:18 UTC (permalink / raw)
To: Alan Stern; +Cc: Linux PM List, Linux USB List, Linus Torvalds
[-- Attachment #1: Type: text/plain, Size: 2371 bytes --]
Hi Alan,
(to the newly added mailing lists - this is a suspend issue with a
Thinkpad X201s. At times it won't suspend... so far USB has been
identified as the culprit... here's more information that Alan requested)
On Tue, 25 Jan 2011 10:24:53 -0500 (EST), Alan Stern <stern@rowland.harvard.edu> wrote:
> On Mon, 24 Jan 2011, Dirk Hohndel wrote:
>
> > > Try building a kernel with CONFIG_USB_DEBUG enabled and see what shows
> > > up in the log. Do you know what the 1-1 device is? (It will show up
> > > in the debug-enabled log, so don't worry if you don't know.)
> >
> > Jan 24 17:51:27 x201s kernel: [ 291.773727] Freezing user space processes ... (elapsed 0.01 seconds) done.
> > Jan 24 17:51:27 x201s kernel: [ 291.785416] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
> > Jan 24 17:51:27 x201s kernel: [ 291.796593] Suspending console(s) (use no_console_suspend to debug)
> > Jan 24 17:51:27 x201s kernel: [ 291.920386] hub 1-1:1.0: suspend error -16
> > Jan 24 17:51:27 x201s kernel: [ 291.920396] pm_op(): usb_dev_suspend+0x0/0x15 returns -16
> > Jan 24 17:51:27 x201s kernel: [ 291.920400] PM: Device 1-1 failed to suspend: error -16
> > Jan 24 17:51:27 x201s kernel: [ 291.920403] PM: Some devices failed to suspend
> > Jan 24 17:51:27 x201s kernel: [ 291.997903] PM: resume of devices complete after 77.528 msecs
> > Jan 24 17:51:27 x201s kernel: [ 291.998062] Restarting tasks ...
>
> It might help to see the dmesg output rather than the system log file.
> Include everything going back to the boot.
Here's the latest, with the latest kernel from Linus: 2.6.38-rc4-00178-g795abaf
which includes the commit that you mentioned bf3d7d40e42a85ca73a34e1385ff34f092a384eb
I did a successfull suspend / resume while the system was in the docking
station - that's around seconds 42-44 in the dmesg output.
Next I undock and do another suspend attempt - starts around second
57. This one failed again, but now we have much more information from
the dmesg output - attached all the way from reboot.
> > 1-1 appears to be my built-in root hub.
>
> No, the root hub is usb1. 1-1 is the device plugged into port 1 of the
> root hub. If you have a debugfs filesystem mounted, you can see the
> device list in /sys/kernel/debug/usb/devices.
I'm attaching that as well :-)
Let me know what else I should send / try.
/D
[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 119717 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.38-rc4-00178-g795abaf (hohndel@x201s.gr8dns.org) (gcc version 4.5.1 20100924 (Red Hat 4.5.1-4) (GCC) ) #15 SMP Mon Feb 14 09:59:06 PST 2011
[ 0.000000] Command line: ro root=UUID=c01e3070-03ef-4331-932f-fa23e59001b6 rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
[ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000bb27c000 (usable)
[ 0.000000] BIOS-e820: 00000000bb27c000 - 00000000bb282000 (reserved)
[ 0.000000] BIOS-e820: 00000000bb282000 - 00000000bb363000 (usable)
[ 0.000000] BIOS-e820: 00000000bb363000 - 00000000bb375000 (reserved)
[ 0.000000] BIOS-e820: 00000000bb375000 - 00000000bb3f6000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bb3f6000 - 00000000bb40f000 (reserved)
[ 0.000000] BIOS-e820: 00000000bb40f000 - 00000000bb470000 (usable)
[ 0.000000] BIOS-e820: 00000000bb470000 - 00000000bb668000 (reserved)
[ 0.000000] BIOS-e820: 00000000bb668000 - 00000000bb6e8000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bb6e8000 - 00000000bb70f000 (reserved)
[ 0.000000] BIOS-e820: 00000000bb70f000 - 00000000bb717000 (usable)
[ 0.000000] BIOS-e820: 00000000bb717000 - 00000000bb71f000 (reserved)
[ 0.000000] BIOS-e820: 00000000bb71f000 - 00000000bb76c000 (usable)
[ 0.000000] BIOS-e820: 00000000bb76c000 - 00000000bb778000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bb778000 - 00000000bb77b000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000bb77b000 - 00000000bb78b000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bb78b000 - 00000000bb78c000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000bb78c000 - 00000000bb79f000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bb79f000 - 00000000bb7ff000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000bb7ff000 - 00000000bb800000 (usable)
[ 0.000000] BIOS-e820: 00000000bb800000 - 00000000c0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000feaff000 - 00000000feb00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 00000001fc000000 (usable)
[ 0.000000] BIOS-e820: 0000000200000000 - 000000023c000000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] DMI: 5129CTO/5129CTO, BIOS 6QET35WW (1.05 ) 01/26/2010
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x23c000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 disabled
[ 0.000000] 1 base 000000000 mask F80000000 write-back
[ 0.000000] 2 base 080000000 mask FC0000000 write-back
[ 0.000000] 3 base 100000000 mask F00000000 write-back
[ 0.000000] 4 base 200000000 mask FC0000000 write-back
[ 0.000000] 5 base 23C000000 mask FFC000000 uncachable
[ 0.000000] 6 base 0BC000000 mask FFC000000 uncachable
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] original variable MTRRs
[ 0.000000] reg 1, base: 0GB, range: 2GB, type WB
[ 0.000000] reg 2, base: 2GB, range: 1GB, type WB
[ 0.000000] reg 3, base: 4GB, range: 4GB, type WB
[ 0.000000] reg 4, base: 8GB, range: 1GB, type WB
[ 0.000000] reg 5, base: 9152MB, range: 64MB, type UC
[ 0.000000] reg 6, base: 3008MB, range: 64MB, type UC
[ 0.000000] total RAM covered: 8064M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 128M num_reg: 6 lose cover RAM: 0G
[ 0.000000] New variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 2GB, type WB
[ 0.000000] reg 1, base: 2GB, range: 1GB, type WB
[ 0.000000] reg 2, base: 3008MB, range: 64MB, type UC
[ 0.000000] reg 3, base: 4GB, range: 4GB, type WB
[ 0.000000] reg 4, base: 8GB, range: 1GB, type WB
[ 0.000000] reg 5, base: 9152MB, range: 64MB, type UC
[ 0.000000] e820 update range: 00000000bc000000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xbb800 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000f6920] f6920
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000bb800000
[ 0.000000] 0000000000 - 00bb800000 page 2M
[ 0.000000] kernel direct mapping tables up to bb800000 @ 1fffc000-20000000
[ 0.000000] init_memory_mapping: 0000000100000000-000000023c000000
[ 0.000000] 0100000000 - 023c000000 page 2M
[ 0.000000] kernel direct mapping tables up to 23c000000 @ bb762000-bb76c000
[ 0.000000] RAMDISK: 37970000 - 37ff0000
[ 0.000000] ACPI: RSDP 00000000000f68f0 00024 (v02 LENOVO)
[ 0.000000] ACPI: XSDT 00000000bb7f08fb 00094 (v01 LENOVO TP-6Q 00001050 LTP 00000000)
[ 0.000000] ACPI: FACP 00000000bb7f0a00 000F4 (v04 LENOVO TP-6Q 00001050 LNVO 00000001)
[ 0.000000] ACPI: DSDT 00000000bb7f0d6b 0DD9B (v01 LENOVO TP-6Q 00001050 MSFT 03000001)
[ 0.000000] ACPI: FACS 00000000bb6e7000 00040
[ 0.000000] ACPI: SSDT 00000000bb7f0bb4 001B7 (v01 LENOVO TP-6Q 00001050 MSFT 03000001)
[ 0.000000] ACPI: ECDT 00000000bb7feb06 00052 (v01 LENOVO TP-6Q 00001050 LNVO 00000001)
[ 0.000000] ACPI: APIC 00000000bb7feb58 00084 (v01 LENOVO TP-6Q 00001050 LNVO 00000001)
[ 0.000000] ACPI: MCFG 00000000bb7fec14 0003C (v01 LENOVO TP-6Q 00001050 LNVO 00000001)
[ 0.000000] ACPI: HPET 00000000bb7fec50 00038 (v01 LENOVO TP-6Q 00001050 LNVO 00000001)
[ 0.000000] ACPI: ASF! 00000000bb7fedbe 000A4 (v16 LENOVO TP-6Q 00001050 PTL 00000001)
[ 0.000000] ACPI: SLIC 00000000bb7fee62 00176 (v01 LENOVO TP-6Q 00001050 LTP 00000000)
[ 0.000000] ACPI: BOOT 00000000bb7fefd8 00028 (v01 LENOVO TP-6Q 00001050 LTP 00000001)
[ 0.000000] ACPI: SSDT 00000000bb6e590a 0085B (v01 LENOVO TP-6Q 00001050 INTL 20050513)
[ 0.000000] ACPI: TCPA 00000000bb78b000 00032 (v02 PTL CRESTLN 06040000 00005A52)
[ 0.000000] ACPI: SSDT 00000000bb77a000 009F1 (v01 PmRef CpuPm 00003000 INTL 20050513)
[ 0.000000] ACPI: SSDT 00000000bb779000 00259 (v01 PmRef Cpu0Tst 00003000 INTL 20050513)
[ 0.000000] ACPI: SSDT 00000000bb778000 0049F (v01 PmRef ApTst 00003000 INTL 20050513)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] [ffffea0000000000-ffffea0007dfffff] PMD -> [ffff8800a8000000-ffff8800aeffffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x0023c000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[9] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x000bb27c
[ 0.000000] 0: 0x000bb282 -> 0x000bb363
[ 0.000000] 0: 0x000bb40f -> 0x000bb470
[ 0.000000] 0: 0x000bb70f -> 0x000bb717
[ 0.000000] 0: 0x000bb71f -> 0x000bb76c
[ 0.000000] 0: 0x000bb7ff -> 0x000bb800
[ 0.000000] 0: 0x00100000 -> 0x001fc000
[ 0.000000] 0: 0x00200000 -> 0x0023c000
[ 0.000000] On node 0 totalpages: 2044834
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 6 pages reserved
[ 0.000000] DMA zone: 3920 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 748620 pages, LIFO batch:31
[ 0.000000] Normal zone: 17696 pages used for memmap
[ 0.000000] Normal zone: 1260256 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000bb27c000 - 00000000bb282000
[ 0.000000] PM: Registered nosave memory: 00000000bb363000 - 00000000bb375000
[ 0.000000] PM: Registered nosave memory: 00000000bb375000 - 00000000bb3f6000
[ 0.000000] PM: Registered nosave memory: 00000000bb3f6000 - 00000000bb40f000
[ 0.000000] PM: Registered nosave memory: 00000000bb470000 - 00000000bb668000
[ 0.000000] PM: Registered nosave memory: 00000000bb668000 - 00000000bb6e8000
[ 0.000000] PM: Registered nosave memory: 00000000bb6e8000 - 00000000bb70f000
[ 0.000000] PM: Registered nosave memory: 00000000bb717000 - 00000000bb71f000
[ 0.000000] PM: Registered nosave memory: 00000000bb76c000 - 00000000bb778000
[ 0.000000] PM: Registered nosave memory: 00000000bb778000 - 00000000bb77b000
[ 0.000000] PM: Registered nosave memory: 00000000bb77b000 - 00000000bb78b000
[ 0.000000] PM: Registered nosave memory: 00000000bb78b000 - 00000000bb78c000
[ 0.000000] PM: Registered nosave memory: 00000000bb78c000 - 00000000bb79f000
[ 0.000000] PM: Registered nosave memory: 00000000bb79f000 - 00000000bb7ff000
[ 0.000000] PM: Registered nosave memory: 00000000bb800000 - 00000000c0000000
[ 0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000feaff000
[ 0.000000] PM: Registered nosave memory: 00000000feaff000 - 00000000feb00000
[ 0.000000] PM: Registered nosave memory: 00000000feb00000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
[ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fed00000
[ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed90000
[ 0.000000] PM: Registered nosave memory: 00000000fed90000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
[ 0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
[ 0.000000] PM: Registered nosave memory: 00000001fc000000 - 0000000200000000
[ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff8800bb000000 s74048 r8192 d24256 u524288
[ 0.000000] pcpu-alloc: s74048 r8192 d24256 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2012796
[ 0.000000] Kernel command line: ro root=UUID=c01e3070-03ef-4331-932f-fa23e59001b6 rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Memory: 7966276k/9371648k available (4556k kernel code, 1192312k absent, 213060k reserved, 6238k data, 688k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:4352 nr_irqs:712 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 83886080 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.001000] Detected 2127.729 MHz processor.
[ 0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 4255.45 BogoMIPS (lpj=2127729)
[ 0.000008] pid_max: default: 32768 minimum: 301
[ 0.000043] Security Framework initialized
[ 0.000099] Mount-cache hash table entries: 256
[ 0.000216] Initializing cgroup subsys ns
[ 0.000220] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.000222] Initializing cgroup subsys cpuacct
[ 0.000227] Initializing cgroup subsys memory
[ 0.000234] Initializing cgroup subsys devices
[ 0.000237] Initializing cgroup subsys freezer
[ 0.000238] Initializing cgroup subsys net_cls
[ 0.000240] Initializing cgroup subsys blkio
[ 0.000263] CPU: Physical Processor ID: 0
[ 0.000264] CPU: Processor Core ID: 0
[ 0.000268] using mwait in idle threads.
[ 0.000322] ACPI: Core revision 20110112
[ 0.024241] ftrace: allocating 23205 entries in 92 pages
[ 0.031028] Setting APIC routing to flat
[ 0.031429] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.041426] CPU0: Intel(R) Core(TM) i7 CPU L 640 @ 2.13GHz stepping 02
[ 0.142665] Performance Events: PEBS fmt1+, Westmere events, Intel PMU driver.
[ 0.142671] ... version: 3
[ 0.142673] ... bit width: 48
[ 0.142674] ... generic registers: 4
[ 0.142675] ... value mask: 0000ffffffffffff
[ 0.142676] ... max period: 000000007fffffff
[ 0.142678] ... fixed-purpose events: 3
[ 0.142679] ... event mask: 000000070000000f
[ 0.143046] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.143133] Booting Node 0, Processors #1
[ 0.233744] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.233857] #2
[ 0.324693] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.324799] #3 Ok.
[ 0.415632] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.415680] Brought up 4 CPUs
[ 0.415682] Total of 4 processors activated (17022.77 BogoMIPS).
[ 0.417088] devtmpfs: initialized
[ 0.417971] atomic64 test passed for x86-64 platform with CX8 and with SSE
[ 0.417995] Time: 18:51:41 Date: 02/14/11
[ 0.418028] NET: Registered protocol family 16
[ 0.418180] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.418183] ACPI: bus type pci registered
[ 0.418267] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.418271] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.472039] PCI: Using configuration type 1 for base access
[ 0.472782] bio: create slab <bio-0> at 0
[ 0.474342] ACPI: EC: EC description table is found, configuring boot EC
[ 0.479618] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.561003] ACPI: SSDT 00000000bb71a918 003EB (v01 PmRef Cpu0Ist 00003000 INTL 20050513)
[ 0.561342] ACPI: Dynamic OEM Table Load:
[ 0.561345] ACPI: SSDT (null) 003EB (v01 PmRef Cpu0Ist 00003000 INTL 20050513)
[ 0.561490] ACPI: SSDT 00000000bb718718 006B2 (v01 PmRef Cpu0Cst 00003001 INTL 20050513)
[ 0.561850] ACPI: Dynamic OEM Table Load:
[ 0.561853] ACPI: SSDT (null) 006B2 (v01 PmRef Cpu0Cst 00003001 INTL 20050513)
[ 0.568838] ACPI: SSDT 00000000bb719a98 00303 (v01 PmRef ApIst 00003000 INTL 20050513)
[ 0.569240] ACPI: Dynamic OEM Table Load:
[ 0.569242] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20050513)
[ 0.571674] ACPI: SSDT 00000000bb717d98 00119 (v01 PmRef ApCst 00003000 INTL 20050513)
[ 0.572025] ACPI: Dynamic OEM Table Load:
[ 0.572027] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20050513)
[ 0.576211] ACPI: Interpreter enabled
[ 0.576214] ACPI: (supports S0 S3 S4 S5)
[ 0.576234] ACPI: Using IOAPIC for interrupt routing
[ 0.580124] ACPI: Power Resource [PUBS] (on)
[ 0.583671] ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
[ 0.590723] ACPI: ACPI Dock Station Driver: 3 docks/bays found
[ 0.590725] HEST: Table not found.
[ 0.590728] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.590742] ACPI: PCI Root Bridge [UNCR] (domain 0000 [bus ff])
[ 0.590788] pci 0000:ff:00.0: [8086:2c62] type 0 class 0x000600
[ 0.590809] pci 0000:ff:00.1: [8086:2d01] type 0 class 0x000600
[ 0.590828] pci 0000:ff:02.0: [8086:2d10] type 0 class 0x000600
[ 0.590844] pci 0000:ff:02.1: [8086:2d11] type 0 class 0x000600
[ 0.590860] pci 0000:ff:02.2: [8086:2d12] type 0 class 0x000600
[ 0.590875] pci 0000:ff:02.3: [8086:2d13] type 0 class 0x000600
[ 0.590901] pci_bus 0000:ff: on NUMA node 0
[ 0.591225] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[ 0.591279] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.591281] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.591284] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.591286] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
[ 0.591288] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
[ 0.591290] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
[ 0.591292] pci_root PNP0A08:00: host bridge window [mem 0xc0000000-0xfebfffff]
[ 0.591302] pci 0000:00:00.0: [8086:0044] type 0 class 0x000600
[ 0.591317] DMAR: BIOS has allocated no shadow GTT; disabling IOMMU for graphics
[ 0.591333] pci 0000:00:02.0: [8086:0046] type 0 class 0x000300
[ 0.591343] pci 0000:00:02.0: reg 10: [mem 0xf2000000-0xf23fffff 64bit]
[ 0.591350] pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.591354] pci 0000:00:02.0: reg 20: [io 0x1800-0x1807]
[ 0.591414] pci 0000:00:16.0: [8086:3b64] type 0 class 0x000780
[ 0.591442] pci 0000:00:16.0: reg 10: [mem 0xf2727800-0xf272780f 64bit]
[ 0.591517] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.591522] pci 0000:00:16.0: PME# disabled
[ 0.591566] pci 0000:00:19.0: [8086:10ea] type 0 class 0x000200
[ 0.591591] pci 0000:00:19.0: reg 10: [mem 0xf2500000-0xf251ffff]
[ 0.591602] pci 0000:00:19.0: reg 14: [mem 0xf2525000-0xf2525fff]
[ 0.591613] pci 0000:00:19.0: reg 18: [io 0x1820-0x183f]
[ 0.591680] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.591686] pci 0000:00:19.0: PME# disabled
[ 0.591717] pci 0000:00:1a.0: [8086:3b3c] type 0 class 0x000c03
[ 0.591742] pci 0000:00:1a.0: reg 10: [mem 0xf2728000-0xf27283ff]
[ 0.591830] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.591835] pci 0000:00:1a.0: PME# disabled
[ 0.591865] pci 0000:00:1b.0: [8086:3b56] type 0 class 0x000403
[ 0.591886] pci 0000:00:1b.0: reg 10: [mem 0xf2520000-0xf2523fff 64bit]
[ 0.591960] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.591965] pci 0000:00:1b.0: PME# disabled
[ 0.591992] pci 0000:00:1c.0: [8086:3b42] type 1 class 0x000604
[ 0.592070] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.592074] pci 0000:00:1c.0: PME# disabled
[ 0.592103] pci 0000:00:1c.3: [8086:3b48] type 1 class 0x000604
[ 0.592179] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.592184] pci 0000:00:1c.3: PME# disabled
[ 0.592211] pci 0000:00:1c.4: [8086:3b4a] type 1 class 0x000604
[ 0.592288] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.592293] pci 0000:00:1c.4: PME# disabled
[ 0.592329] pci 0000:00:1d.0: [8086:3b34] type 0 class 0x000c03
[ 0.592354] pci 0000:00:1d.0: reg 10: [mem 0xf2728400-0xf27287ff]
[ 0.592444] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.592448] pci 0000:00:1d.0: PME# disabled
[ 0.592472] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.592551] pci 0000:00:1f.0: [8086:3b07] type 0 class 0x000601
[ 0.592670] pci 0000:00:1f.2: [8086:3b2f] type 0 class 0x000106
[ 0.592696] pci 0000:00:1f.2: reg 10: [io 0x1860-0x1867]
[ 0.592707] pci 0000:00:1f.2: reg 14: [io 0x1814-0x1817]
[ 0.592718] pci 0000:00:1f.2: reg 18: [io 0x1818-0x181f]
[ 0.592729] pci 0000:00:1f.2: reg 1c: [io 0x1810-0x1813]
[ 0.592740] pci 0000:00:1f.2: reg 20: [io 0x1840-0x185f]
[ 0.592751] pci 0000:00:1f.2: reg 24: [mem 0xf2727000-0xf27277ff]
[ 0.592797] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.592802] pci 0000:00:1f.2: PME# disabled
[ 0.592824] pci 0000:00:1f.3: [8086:3b30] type 0 class 0x000c05
[ 0.592845] pci 0000:00:1f.3: reg 10: [mem 0xf2728800-0xf27288ff 64bit]
[ 0.592875] pci 0000:00:1f.3: reg 20: [io 0x1880-0x189f]
[ 0.592922] pci 0000:00:1f.6: [8086:3b32] type 0 class 0x001180
[ 0.592949] pci 0000:00:1f.6: reg 10: [mem 0xf2526000-0xf2526fff 64bit]
[ 0.593083] pci 0000:00:1c.0: PCI bridge to [bus 0d-0d]
[ 0.593088] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.593093] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.593100] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.593156] pci 0000:00:1c.3: PCI bridge to [bus 05-0c]
[ 0.593160] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff]
[ 0.593165] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf1ffffff]
[ 0.593173] pci 0000:00:1c.3: bridge window [mem 0xf2800000-0xf28fffff 64bit pref]
[ 0.593321] pci 0000:02:00.0: [8086:4238] type 0 class 0x000280
[ 0.593385] pci 0000:02:00.0: reg 10: [mem 0xf2400000-0xf2401fff 64bit]
[ 0.593602] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.593629] pci 0000:02:00.0: PME# disabled
[ 0.593729] pci 0000:00:1c.4: PCI bridge to [bus 02-02]
[ 0.593733] pci 0000:00:1c.4: bridge window [io 0xf000-0x0000] (disabled)
[ 0.593738] pci 0000:00:1c.4: bridge window [mem 0xf2400000-0xf24fffff]
[ 0.593746] pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.593820] pci 0000:00:1e.0: PCI bridge to [bus 0e-0e] (subtractive decode)
[ 0.593825] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.593829] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.593837] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.593839] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.593841] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.593844] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.593846] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
[ 0.593848] pci 0000:00:1e.0: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
[ 0.593850] pci 0000:00:1e.0: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
[ 0.593853] pci 0000:00:1e.0: bridge window [mem 0xc0000000-0xfebfffff] (subtractive decode)
[ 0.593877] pci_bus 0000:00: on NUMA node 0
[ 0.593880] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.594008] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 0.594042] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
[ 0.594076] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP5._PRT]
[ 0.597335] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.597400] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.597452] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[ 0.597516] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.597588] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.597640] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[ 0.597692] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[ 0.597755] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.597839] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.597846] vgaarb: loaded
[ 0.597921] SCSI subsystem initialized
[ 0.597935] libata version 3.00 loaded.
[ 0.597975] usbcore: registered new interface driver usbfs
[ 0.597987] usbcore: registered new interface driver hub
[ 0.598022] usbcore: registered new device driver usb
[ 0.598056] PCI: Using ACPI for IRQ routing
[ 0.598058] PCI: pci_cache_line_size set to 64 bytes
[ 0.598138] reserve RAM buffer: 000000000009e800 - 000000000009ffff
[ 0.598141] reserve RAM buffer: 00000000bb27c000 - 00000000bbffffff
[ 0.598146] reserve RAM buffer: 00000000bb363000 - 00000000bbffffff
[ 0.598151] reserve RAM buffer: 00000000bb470000 - 00000000bbffffff
[ 0.598155] reserve RAM buffer: 00000000bb717000 - 00000000bbffffff
[ 0.598158] reserve RAM buffer: 00000000bb76c000 - 00000000bbffffff
[ 0.598161] reserve RAM buffer: 00000000bb800000 - 00000000bbffffff
[ 0.598249] NetLabel: Initializing
[ 0.598251] NetLabel: domain hash size = 128
[ 0.598252] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.598263] NetLabel: unlabeled traffic allowed by default
[ 0.598278] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.598282] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.600306] Switching to clocksource hpet
[ 0.600456] Switched to NOHz mode on CPU #0
[ 0.600529] Switched to NOHz mode on CPU #3
[ 0.600543] Switched to NOHz mode on CPU #2
[ 0.600552] Switched to NOHz mode on CPU #1
[ 0.606585] pnp: PnP ACPI init
[ 0.606606] ACPI: bus type pnp registered
[ 0.607893] pnp 00:00: [mem 0x00000000-0x0009ffff]
[ 0.607896] pnp 00:00: [mem 0x000c0000-0x000c3fff]
[ 0.607897] pnp 00:00: [mem 0x000c4000-0x000c7fff]
[ 0.607899] pnp 00:00: [mem 0x000c8000-0x000cbfff]
[ 0.607901] pnp 00:00: [mem 0x000cc000-0x000cffff]
[ 0.607903] pnp 00:00: [mem 0x000d0000-0x000cffff disabled]
[ 0.607905] pnp 00:00: [mem 0x000d4000-0x000d3fff disabled]
[ 0.607906] pnp 00:00: [mem 0x000d8000-0x000d7fff disabled]
[ 0.607908] pnp 00:00: [mem 0x000dc000-0x000dffff]
[ 0.607910] pnp 00:00: [mem 0x000e0000-0x000e3fff]
[ 0.607912] pnp 00:00: [mem 0x000e4000-0x000e7fff]
[ 0.607913] pnp 00:00: [mem 0x000e8000-0x000ebfff]
[ 0.607915] pnp 00:00: [mem 0x000ec000-0x000effff]
[ 0.607917] pnp 00:00: [mem 0x000f0000-0x000fffff]
[ 0.607918] pnp 00:00: [mem 0x00100000-0xbfffffff]
[ 0.607920] pnp 00:00: [mem 0xfec00000-0xfed3ffff]
[ 0.607922] pnp 00:00: [mem 0xfed4c000-0xffffffff]
[ 0.607995] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.607998] system 00:00: [mem 0x000c0000-0x000c3fff] has been reserved
[ 0.608000] system 00:00: [mem 0x000c4000-0x000c7fff] has been reserved
[ 0.608002] system 00:00: [mem 0x000c8000-0x000cbfff] has been reserved
[ 0.608004] system 00:00: [mem 0x000cc000-0x000cffff] has been reserved
[ 0.608007] system 00:00: [mem 0x000dc000-0x000dffff] could not be reserved
[ 0.608010] system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved
[ 0.608012] system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved
[ 0.608015] system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved
[ 0.608017] system 00:00: [mem 0x000ec000-0x000effff] could not be reserved
[ 0.608019] system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
[ 0.608022] system 00:00: [mem 0x00100000-0xbfffffff] could not be reserved
[ 0.608025] system 00:00: [mem 0xfec00000-0xfed3ffff] could not be reserved
[ 0.608027] system 00:00: [mem 0xfed4c000-0xffffffff] could not be reserved
[ 0.608031] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.608045] pnp 00:01: [bus ff]
[ 0.608108] pnp 00:01: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.608124] pnp 00:02: [bus 00-fe]
[ 0.608126] pnp 00:02: [io 0x0cf8-0x0cff]
[ 0.608128] pnp 00:02: [io 0x0000-0x0cf7 window]
[ 0.608131] pnp 00:02: [io 0x0d00-0xffff window]
[ 0.608133] pnp 00:02: [mem 0x000a0000-0x000bffff window]
[ 0.608135] pnp 00:02: [mem 0x000c0000-0x000c3fff window]
[ 0.608137] pnp 00:02: [mem 0x000c4000-0x000c7fff window]
[ 0.608138] pnp 00:02: [mem 0x000c8000-0x000cbfff window]
[ 0.608140] pnp 00:02: [mem 0x000cc000-0x000cffff window]
[ 0.608142] pnp 00:02: [mem 0x000d0000-0x000d3fff window]
[ 0.608144] pnp 00:02: [mem 0x000d4000-0x000d7fff window]
[ 0.608145] pnp 00:02: [mem 0x000d8000-0x000dbfff window]
[ 0.608147] pnp 00:02: [mem 0x000dc000-0x000dffff window]
[ 0.608149] pnp 00:02: [mem 0x000e0000-0x000e3fff window]
[ 0.608151] pnp 00:02: [mem 0x000e4000-0x000e7fff window]
[ 0.608153] pnp 00:02: [mem 0x000e8000-0x000ebfff window]
[ 0.608154] pnp 00:02: [mem 0x000ec000-0x000effff window]
[ 0.608156] pnp 00:02: [mem 0xc0000000-0xfebfffff window]
[ 0.608158] pnp 00:02: [mem 0xfed40000-0xfed4bfff window]
[ 0.608195] pnp 00:02: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.608476] pnp 00:03: [io 0x0010-0x001f]
[ 0.608478] pnp 00:03: [io 0x0090-0x009f]
[ 0.608480] pnp 00:03: [io 0x0024-0x0025]
[ 0.608482] pnp 00:03: [io 0x0028-0x0029]
[ 0.608483] pnp 00:03: [io 0x002c-0x002d]
[ 0.608485] pnp 00:03: [io 0x0030-0x0031]
[ 0.608486] pnp 00:03: [io 0x0034-0x0035]
[ 0.608488] pnp 00:03: [io 0x0038-0x0039]
[ 0.608489] pnp 00:03: [io 0x003c-0x003d]
[ 0.608491] pnp 00:03: [io 0x00a4-0x00a5]
[ 0.608492] pnp 00:03: [io 0x00a8-0x00a9]
[ 0.608494] pnp 00:03: [io 0x00ac-0x00ad]
[ 0.608495] pnp 00:03: [io 0x00b0-0x00b5]
[ 0.608497] pnp 00:03: [io 0x00b8-0x00b9]
[ 0.608499] pnp 00:03: [io 0x00bc-0x00bd]
[ 0.608500] pnp 00:03: [io 0x0050-0x0053]
[ 0.608502] pnp 00:03: [io 0x0072-0x0077]
[ 0.608503] pnp 00:03: [io 0x164e-0x164f]
[ 0.608505] pnp 00:03: [io 0x002e-0x002f]
[ 0.608506] pnp 00:03: [io 0x1000-0x107f]
[ 0.608508] pnp 00:03: [io 0x1180-0x11ff]
[ 0.608509] pnp 00:03: [io 0x0800-0x080f]
[ 0.608511] pnp 00:03: [io 0x15e0-0x15ef]
[ 0.608512] pnp 00:03: [io 0x1600-0x1641]
[ 0.608514] pnp 00:03: [io 0x1644-0x167f]
[ 0.608516] pnp 00:03: [mem 0xe0000000-0xefffffff]
[ 0.608519] pnp 00:03: [mem 0xfed1c000-0xfed1ffff]
[ 0.608521] pnp 00:03: [mem 0xfed10000-0xfed13fff]
[ 0.608522] pnp 00:03: [mem 0xfed18000-0xfed18fff]
[ 0.608524] pnp 00:03: [mem 0xfed19000-0xfed19fff]
[ 0.608526] pnp 00:03: [mem 0xfed45000-0xfed4bfff]
[ 0.608590] system 00:03: [io 0x164e-0x164f] has been reserved
[ 0.608592] system 00:03: [io 0x1000-0x107f] has been reserved
[ 0.608594] system 00:03: [io 0x1180-0x11ff] has been reserved
[ 0.608598] system 00:03: [io 0x0800-0x080f] has been reserved
[ 0.608600] system 00:03: [io 0x15e0-0x15ef] has been reserved
[ 0.608602] system 00:03: [io 0x1600-0x1641] has been reserved
[ 0.608605] system 00:03: [io 0x1644-0x167f] could not be reserved
[ 0.608608] system 00:03: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.608610] system 00:03: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.608612] system 00:03: [mem 0xfed10000-0xfed13fff] has been reserved
[ 0.608615] system 00:03: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.608617] system 00:03: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.608620] system 00:03: [mem 0xfed45000-0xfed4bfff] has been reserved
[ 0.608623] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.608652] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 0.608684] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.608693] pnp 00:05: [io 0x0000-0x000f]
[ 0.608694] pnp 00:05: [io 0x0080-0x008f]
[ 0.608696] pnp 00:05: [io 0x00c0-0x00df]
[ 0.608698] pnp 00:05: [dma 4]
[ 0.608727] pnp 00:05: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.608734] pnp 00:06: [io 0x0061]
[ 0.608761] pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.608769] pnp 00:07: [io 0x00f0]
[ 0.608781] pnp 00:07: [irq 13]
[ 0.608810] pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.608818] pnp 00:08: [io 0x0070-0x0071]
[ 0.608823] pnp 00:08: [irq 8]
[ 0.608851] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.608859] pnp 00:09: [io 0x0060]
[ 0.608861] pnp 00:09: [io 0x0064]
[ 0.608866] pnp 00:09: [irq 1]
[ 0.608895] pnp 00:09: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.608906] pnp 00:0a: [irq 12]
[ 0.608935] pnp 00:0a: Plug and Play ACPI device, IDs IBM3780 PNP0f13 (active)
[ 0.609196] pnp 00:0b: [mem 0xfed40000-0xfed44fff]
[ 0.609230] pnp 00:0b: Plug and Play ACPI device, IDs SMO1200 PNP0c31 (active)
[ 0.609712] pnp 00:0c: [mem 0xfeaff000-0xfeafffff]
[ 0.609774] system 00:0c: [mem 0xfeaff000-0xfeafffff] has been reserved
[ 0.609777] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.609857] pnp: PnP ACPI: found 13 devices
[ 0.609858] ACPI: ACPI bus type pnp unregistered
[ 0.616202] pci 0000:00:1c.0: PCI bridge to [bus 0d-0d]
[ 0.616204] pci 0000:00:1c.0: bridge window [io disabled]
[ 0.616210] pci 0000:00:1c.0: bridge window [mem disabled]
[ 0.616214] pci 0000:00:1c.0: bridge window [mem pref disabled]
[ 0.616222] pci 0000:00:1c.3: PCI bridge to [bus 05-0c]
[ 0.616225] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff]
[ 0.616232] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf1ffffff]
[ 0.616237] pci 0000:00:1c.3: bridge window [mem 0xf2800000-0xf28fffff 64bit pref]
[ 0.616245] pci 0000:00:1c.4: PCI bridge to [bus 02-02]
[ 0.616247] pci 0000:00:1c.4: bridge window [io disabled]
[ 0.616253] pci 0000:00:1c.4: bridge window [mem 0xf2400000-0xf24fffff]
[ 0.616257] pci 0000:00:1c.4: bridge window [mem pref disabled]
[ 0.616265] pci 0000:00:1e.0: PCI bridge to [bus 0e-0e]
[ 0.616267] pci 0000:00:1e.0: bridge window [io disabled]
[ 0.616273] pci 0000:00:1e.0: bridge window [mem disabled]
[ 0.616277] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.616298] pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.616304] pci 0000:00:1c.0: setting latency timer to 64
[ 0.616315] pci 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 0.616320] pci 0000:00:1c.3: setting latency timer to 64
[ 0.616327] pci 0000:00:1c.4: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.616331] pci 0000:00:1c.4: setting latency timer to 64
[ 0.616339] pci 0000:00:1e.0: setting latency timer to 64
[ 0.616344] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.616345] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.616347] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.616349] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
[ 0.616351] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
[ 0.616353] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
[ 0.616363] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xfebfffff]
[ 0.616365] pci_bus 0000:05: resource 0 [io 0x2000-0x2fff]
[ 0.616367] pci_bus 0000:05: resource 1 [mem 0xf0000000-0xf1ffffff]
[ 0.616369] pci_bus 0000:05: resource 2 [mem 0xf2800000-0xf28fffff 64bit pref]
[ 0.616371] pci_bus 0000:02: resource 1 [mem 0xf2400000-0xf24fffff]
[ 0.616373] pci_bus 0000:0e: resource 4 [io 0x0000-0x0cf7]
[ 0.616375] pci_bus 0000:0e: resource 5 [io 0x0d00-0xffff]
[ 0.616377] pci_bus 0000:0e: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.616379] pci_bus 0000:0e: resource 7 [mem 0x000d0000-0x000d3fff]
[ 0.616381] pci_bus 0000:0e: resource 8 [mem 0x000d4000-0x000d7fff]
[ 0.616382] pci_bus 0000:0e: resource 9 [mem 0x000d8000-0x000dbfff]
[ 0.616384] pci_bus 0000:0e: resource 10 [mem 0xc0000000-0xfebfffff]
[ 0.616411] NET: Registered protocol family 2
[ 0.616454] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.616865] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.618042] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.618328] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.618330] TCP reno registered
[ 0.618333] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.618398] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.618539] NET: Registered protocol family 1
[ 0.618567] pci 0000:00:02.0: Boot video device
[ 0.618678] PCI: CLS 64 bytes, default 64
[ 0.618730] Trying to unpack rootfs image as initramfs...
[ 0.740368] Freeing initrd memory: 6656k freed
[ 0.741863] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.741869] Placing 64MB software IO TLB between ffff8800b6278000 - ffff8800ba278000
[ 0.741871] software IO TLB at phys 0xb6278000 - 0xba278000
[ 0.741921] Simple Boot Flag at 0x35 set to 0x1
[ 0.754591] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.757869] Btrfs loaded
[ 0.757874] msgmni has been set to 15572
[ 0.758116] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.758119] io scheduler noop registered
[ 0.758121] io scheduler deadline registered
[ 0.758153] io scheduler cfq registered (default)
[ 0.758441] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.758463] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.758464] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.758666] acpiphp: Slot [1] registered
[ 0.758765] intel_idle: MWAIT substates: 0x1120
[ 0.758767] intel_idle: v0.4 model 0x25
[ 0.758768] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.758991] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 0.759196] ACPI: AC Adapter [AC] (on-line)
[ 0.759286] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[ 0.775317] ACPI: Lid Switch [LID]
[ 0.775412] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
[ 0.783330] ACPI: Sleep Button [SLPB]
[ 0.783421] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.783424] ACPI: Power Button [PWRF]
[ 0.783543] ACPI: acpi_idle yielding to intel_idle
[ 0.790074] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.790076] ACPI: Thermal Zone [THM0] (67 C)
[ 0.790089] ERST: Table is not found!
[ 0.790183] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.806877] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 0.806883] ACPI: Battery Slot [BAT0] (battery present)
[ 0.808688] Non-volatile memory driver v1.3
[ 0.808691] Linux agpgart interface v0.103
[ 0.808745] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset
[ 0.808885] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 0.810085] agpgart-intel 0000:00:00.0: detected 32768K stolen memory
[ 0.810213] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 0.810359] tpm_tis 00:0b: 1.2 TPM (device-id 0x0, rev-id 78)
[ 0.840359] [drm] Initialized drm 1.1.0 20060810
[ 0.840409] i915 0000:00:02.0: power state changed by ACPI to D0
[ 0.840412] i915 0000:00:02.0: power state changed by ACPI to D0
[ 0.840428] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.840432] i915 0000:00:02.0: setting latency timer to 64
[ 0.905603] i915 0000:00:02.0: irq 40 for MSI/MSI-X
[ 0.905610] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 0.905612] [drm] Driver supports precise vblank timestamp query.
[ 1.057306] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 1.184262] fbcon: inteldrmfb (fb0) is primary device
[ 1.300221] Console: switching to colour frame buffer device 180x56
[ 1.303167] fb0: inteldrmfb frame buffer device
[ 1.303168] drm: registered panic notifier
[ 1.303187] No ACPI video bus found
[ 1.303311] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 1.304449] brd: module loaded
[ 1.305003] loop: module loaded
[ 1.305094] ahci 0000:00:1f.2: version 3.0
[ 1.305108] ahci 0000:00:1f.2: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 1.305159] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 1.305195] ahci: SSS flag set, parallel bus scan disabled
[ 1.305244] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x33 impl SATA mode
[ 1.305248] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part ems sxs apst
[ 1.305254] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.311712] scsi0 : ahci
[ 1.311807] scsi1 : ahci
[ 1.311876] scsi2 : ahci
[ 1.311943] scsi3 : ahci
[ 1.312012] scsi4 : ahci
[ 1.312106] scsi5 : ahci
[ 1.312505] ata1: SATA max UDMA/133 abar m2048@0xf2727000 port 0xf2727100 irq 41
[ 1.312509] ata2: SATA max UDMA/133 abar m2048@0xf2727000 port 0xf2727180 irq 41
[ 1.312511] ata3: DUMMY
[ 1.312512] ata4: DUMMY
[ 1.312514] ata5: SATA max UDMA/133 abar m2048@0xf2727000 port 0xf2727300 irq 41
[ 1.312518] ata6: SATA max UDMA/133 abar m2048@0xf2727000 port 0xf2727380 irq 41
[ 1.312655] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 1.316112] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.316118] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.316212] mousedev: PS/2 mouse device common for all mice
[ 1.316333] rtc_cmos 00:08: RTC can wake from S4
[ 1.316410] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 1.316442] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.316526] device-mapper: uevent: version 1.0.3
[ 1.316605] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised: dm-devel@redhat.com
[ 1.316757] cpuidle: using governor ladder
[ 1.316927] cpuidle: using governor menu
[ 1.317046] usbcore: registered new interface driver usbhid
[ 1.317047] usbhid: USB HID core driver
[ 1.317106] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 1.317362] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.317388] TCP cubic registered
[ 1.317390] Initializing XFRM netlink socket
[ 1.317410] NET: Registered protocol family 17
[ 1.317438] Registering the dns_resolver key type
[ 1.317638] PM: Hibernation image not present or could not be loaded.
[ 1.319802] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.324157] IMA: No TPM chip found, activating TPM-bypass!
[ 1.324570] Magic number: 15:275:898
[ 1.324766] rtc_cmos 00:08: setting system clock to 2011-02-14 18:51:41 UTC (1297709501)
[ 1.324913] Initalizing network drop monitor service
[ 1.742072] Refined TSC clocksource calibration: 2127.999 MHz.
[ 1.742078] Switching to clocksource tsc
[ 1.772002] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.772577] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 1.772585] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.772591] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.773017] ata1.00: ATA-9: C300-CTFDDAC256MAG, 0002, max UDMA/100
[ 1.773023] ata1.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.773664] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 1.773671] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.773678] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.774105] ata1.00: configured for UDMA/100
[ 1.774290] scsi 0:0:0:0: Direct-Access ATA C300-CTFDDAC256M 0002 PQ: 0 ANSI: 5
[ 1.774501] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.774577] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 1.774723] sd 0:0:0:0: [sda] Write Protect is off
[ 1.774728] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.774764] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.775361] sda: sda1 sda2 sda3 sda4
[ 1.775980] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.078839] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.383713] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.688582] ata6: SATA link down (SStatus 0 SControl 300)
[ 2.691881] Freeing unused kernel memory: 688k freed
[ 2.692027] Write protecting the kernel read-only data: 10240k
[ 2.704478] Freeing unused kernel memory: 1568k freed
[ 2.719289] Freeing unused kernel memory: 1880k freed
[ 2.741348] dracut: dracut-006-6.fc14
[ 2.749541] dracut: rd_NO_LUKS: removing cryptoluks activation
[ 2.755208] udev[83]: starting version 161
[ 2.831174] dracut: Starting plymouth daemon
[ 3.782934] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.782939] ehci_hcd: block sizes: qh 104 qtd 96 itd 192 sitd 96
[ 3.782979] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 3.782985] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 3.782997] ehci_hcd 0000:00:1a.0: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 3.783054] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 3.783060] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 3.783084] /home/hohndel/linux/drivers/usb/core/inode.c: creating file 'devices'
[ 3.783089] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '001'
[ 3.783173] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 3.789121] ehci_hcd 0000:00:1a.0: reset hcs_params 0x200003 dbg=2 cc=0 pcc=0 ordered !ppc ports=3
[ 3.789133] ehci_hcd 0000:00:1a.0: reset hcc_params 36881 caching frame 1024 64 bit addr
[ 3.789181] ehci_hcd 0000:00:1a.0: support lpm
[ 3.789196] ehci_hcd 0000:00:1a.0: debug port 2
[ 3.789202] ehci_hcd 0000:00:1a.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 3.793093] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 3.793097] ehci_hcd 0000:00:1a.0: supports USB remote wakeup
[ 3.793127] ehci_hcd 0000:00:1a.0: irq 23, io mem 0xf2728000
[ 3.793134] ehci_hcd 0000:00:1a.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 3.797025] ehci_hcd 0000:00:1a.0: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[ 3.804045] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 3.804086] usb usb1: default language 0x0409
[ 3.804096] usb usb1: udev 1, busnum 1, minor = 0
[ 3.804099] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.804102] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.804105] usb usb1: Product: EHCI Host Controller
[ 3.804107] usb usb1: Manufacturer: Linux 2.6.38-rc4-00178-g795abaf ehci_hcd
[ 3.804110] usb usb1: SerialNumber: 0000:00:1a.0
[ 3.804264] usb usb1: usb_probe_device
[ 3.804268] usb usb1: configuration #1 chosen from 1 choice
[ 3.804280] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 3.804329] hub 1-0:1.0: usb_probe_interface
[ 3.804331] hub 1-0:1.0: usb_probe_interface - got id
[ 3.804335] hub 1-0:1.0: USB hub found
[ 3.804341] hub 1-0:1.0: 3 ports detected
[ 3.804343] hub 1-0:1.0: standalone hub
[ 3.804345] hub 1-0:1.0: no power switching (usb 1.0)
[ 3.804347] hub 1-0:1.0: individual port over-current protection
[ 3.804350] hub 1-0:1.0: power on to power good time: 20ms
[ 3.804357] hub 1-0:1.0: local power source is good
[ 3.804360] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 3.804410] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '001'
[ 3.804525] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 3.804532] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 3.804557] ehci_hcd 0000:00:1d.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 3.804598] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.804602] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 3.804611] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '002'
[ 3.804671] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 3.807064] ehci_hcd 0000:00:1d.0: reset hcs_params 0x200003 dbg=2 cc=0 pcc=0 ordered !ppc ports=3
[ 3.807070] ehci_hcd 0000:00:1d.0: reset hcc_params 36881 caching frame 1024 64 bit addr
[ 3.807101] ehci_hcd 0000:00:1d.0: support lpm
[ 3.807116] ehci_hcd 0000:00:1d.0: debug port 2
[ 3.807122] ehci_hcd 0000:00:1d.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 3.811035] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 3.811038] ehci_hcd 0000:00:1d.0: supports USB remote wakeup
[ 3.811093] ehci_hcd 0000:00:1d.0: irq 19, io mem 0xf2728400
[ 3.811099] ehci_hcd 0000:00:1d.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 3.814986] ehci_hcd 0000:00:1d.0: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[ 3.820021] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 3.820075] usb usb2: default language 0x0409
[ 3.820085] usb usb2: udev 1, busnum 2, minor = 128
[ 3.820088] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.820090] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.820094] usb usb2: Product: EHCI Host Controller
[ 3.820095] usb usb2: Manufacturer: Linux 2.6.38-rc4-00178-g795abaf ehci_hcd
[ 3.820098] usb usb2: SerialNumber: 0000:00:1d.0
[ 3.820222] usb usb2: usb_probe_device
[ 3.820226] usb usb2: configuration #1 chosen from 1 choice
[ 3.820237] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 3.820280] hub 2-0:1.0: usb_probe_interface
[ 3.820283] hub 2-0:1.0: usb_probe_interface - got id
[ 3.820286] hub 2-0:1.0: USB hub found
[ 3.820292] hub 2-0:1.0: 3 ports detected
[ 3.820294] hub 2-0:1.0: standalone hub
[ 3.820297] hub 2-0:1.0: no power switching (usb 1.0)
[ 3.820299] hub 2-0:1.0: individual port over-current protection
[ 3.820302] hub 2-0:1.0: power on to power good time: 20ms
[ 3.820307] hub 2-0:1.0: local power source is good
[ 3.820310] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 3.820352] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '001'
[ 3.885588] device fsid 3143ef0370301ec0-b60190e523fa2f93 devid 1 transid 771295 /dev/sda4
[ 3.904003] ehci_hcd 0000:00:1a.0: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT
[ 3.904016] hub 1-0:1.0: port 1: status 0501 change 0001
[ 3.919978] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT
[ 3.919984] hub 2-0:1.0: port 1: status 0501 change 0001
[ 3.976801] Btrfs detected SSD devices, enabling SSD mode
[ 3.981403] dracut: Mounted root filesystem /dev/sda4
[ 4.003400] dracut: Loading SELinux policy
[ 4.003966] hub 1-0:1.0: state 7 ports 3 chg 0002 evt 0000
[ 4.003986] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[ 4.055195] ehci_hcd 0000:00:1a.0: port 1 high speed
[ 4.055201] ehci_hcd 0000:00:1a.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 4.077132] dracut: /sbin/load_policy: Can't load policy: No such device
[ 4.105957] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 4.155304] dracut: Switching root
[ 4.157153] ehci_hcd 0000:00:1a.0: port 1 high speed
[ 4.157168] ehci_hcd 0000:00:1a.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 4.220013] ehci_hcd 0000:00:1a.0: set dev address 2 for port 1
[ 4.220020] ehci_hcd 0000:00:1a.0: LPM: no device attached
[ 4.220262] usb 1-1: udev 2, busnum 1, minor = 1
[ 4.220266] usb 1-1: New USB device found, idVendor=8087, idProduct=0020
[ 4.220269] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.220393] usb 1-1: usb_probe_device
[ 4.220397] usb 1-1: configuration #1 chosen from 1 choice
[ 4.220513] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 4.220553] hub 1-1:1.0: usb_probe_interface
[ 4.220556] hub 1-1:1.0: usb_probe_interface - got id
[ 4.220560] hub 1-1:1.0: USB hub found
[ 4.220633] hub 1-1:1.0: 6 ports detected
[ 4.220636] hub 1-1:1.0: standalone hub
[ 4.220638] hub 1-1:1.0: individual port power switching
[ 4.220640] hub 1-1:1.0: individual port over-current protection
[ 4.220643] hub 1-1:1.0: Single TT
[ 4.220645] hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
[ 4.220648] hub 1-1:1.0: Port indicators are supported
[ 4.220651] hub 1-1:1.0: power on to power good time: 100ms
[ 4.220884] hub 1-1:1.0: local power source is good
[ 4.220887] hub 1-1:1.0: enabling power on all ports
[ 4.221662] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '002'
[ 4.221698] hub 2-0:1.0: state 7 ports 3 chg 0002 evt 0000
[ 4.221708] hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[ 4.245354] readahead-collector: starting
[ 4.272104] ehci_hcd 0000:00:1d.0: port 1 high speed
[ 4.272116] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 4.279248] readahead-collector: sorting
[ 4.321351] hub 1-1:1.0: port 4: status 0101 change 0001
[ 4.321600] hub 1-1:1.0: port 5: status 0101 change 0001
[ 4.322818] usb 2-1: new high speed USB device using ehci_hcd and address 2
[ 4.361249] udev[292]: starting version 161
[ 4.374058] ehci_hcd 0000:00:1d.0: port 1 high speed
[ 4.374065] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 4.422111] usb 1-1: link qh256-0001/ffff880230a65480 start 1 [1/0 us]
[ 4.440926] ehci_hcd 0000:00:1d.0: set dev address 2 for port 1
[ 4.440933] ehci_hcd 0000:00:1d.0: LPM: no device attached
[ 4.441170] usb 2-1: udev 2, busnum 2, minor = 129
[ 4.441174] usb 2-1: New USB device found, idVendor=8087, idProduct=0020
[ 4.441177] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.441293] usb 2-1: usb_probe_device
[ 4.441298] usb 2-1: configuration #1 chosen from 1 choice
[ 4.441422] usb 2-1: adding 2-1:1.0 (config #1, interface 0)
[ 4.441463] hub 2-1:1.0: usb_probe_interface
[ 4.441465] hub 2-1:1.0: usb_probe_interface - got id
[ 4.441469] hub 2-1:1.0: USB hub found
[ 4.441540] hub 2-1:1.0: 8 ports detected
[ 4.441543] hub 2-1:1.0: standalone hub
[ 4.441545] hub 2-1:1.0: individual port power switching
[ 4.441547] hub 2-1:1.0: individual port over-current protection
[ 4.441549] hub 2-1:1.0: Single TT
[ 4.441551] hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
[ 4.441554] hub 2-1:1.0: Port indicators are supported
[ 4.441556] hub 2-1:1.0: power on to power good time: 100ms
[ 4.441791] hub 2-1:1.0: local power source is good
[ 4.441795] hub 2-1:1.0: enabling power on all ports
[ 4.442827] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '002'
[ 4.442867] hub 1-1:1.0: state 7 ports 6 chg 0030 evt 0000
[ 4.442921] hub 1-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
[ 4.448072] iTCO_vendor_support: vendor-support=0
[ 4.448321] i801_smbus 0000:00:1f.3: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 4.453926] hub 1-1:1.0: port 4 not reset yet, waiting 10ms
[ 4.461642] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[ 4.461792] iTCO_wdt: Found a QM57 TCO device (Version=2, TCOBASE=0x1060)
[ 4.461878] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 4.486552] intel ips 0000:00:1f.6: CPU TDP doesn't match expected value (found 18, expected 21)
[ 4.486572] intel ips 0000:00:1f.6: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 4.489798] intel ips 0000:00:1f.6: IPS driver initialized, MCP temp limit 90
[ 4.502598] microcode: CPU0 sig=0x20652, pf=0x10, revision=0x9
[ 4.504139] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-k2
[ 4.504143] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 4.504182] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 4.504199] e1000e 0000:00:19.0: setting latency timer to 64
[ 4.504369] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X
[ 4.509988] thinkpad_acpi: ThinkPad ACPI Extras v0.24
[ 4.509991] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 4.509993] thinkpad_acpi: ThinkPad BIOS 6QET35WW (1.05 ), EC 6QHT24WW-1.05
[ 4.509995] thinkpad_acpi: Lenovo ThinkPad X201s, model 5129CTO
[ 4.515966] usb 1-1.4: new full speed USB device using ehci_hcd and address 3
[ 4.520246] thinkpad_acpi: detected a 8-level brightness capable ThinkPad
[ 4.521827] thinkpad_acpi: radio switch found; radios are enabled
[ 4.522332] thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode
[ 4.526893] hub 1-1:1.0: port 4 not reset yet, waiting 10ms
[ 4.543763] usb 2-1: link qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 4.547060] cfg80211: Calling CRDA to update world regulatory domain
[ 4.548020] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[ 4.548381] microcode: CPU1 sig=0x20652, pf=0x10, revision=0x9
[ 4.553007] Registered led device: tpacpi::thinklight
[ 4.553306] Registered led device: tpacpi::power
[ 4.553591] Registered led device: tpacpi::standby
[ 4.553872] Registered led device: tpacpi::thinkvantage
[ 4.557234] microcode: CPU2 sig=0x20652, pf=0x10, revision=0x9
[ 4.560104] microcode: CPU3 sig=0x20652, pf=0x10, revision=0x9
[ 4.579335] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 4.585428] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
[ 4.595312] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input4
[ 4.609698] usb 1-1.4: skipped 1 descriptor after interface
[ 4.610023] usb 1-1.4: default language 0x0409
[ 4.610954] microcode: CPU0 updated to revision 0xc, date = 2010-06-10
[ 4.611403] microcode: CPU1 updated to revision 0xc, date = 2010-06-10
[ 4.611423] usb 1-1.4: udev 3, busnum 1, minor = 2
[ 4.611427] usb 1-1.4: New USB device found, idVendor=0a5c, idProduct=217f
[ 4.611430] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.611433] usb 1-1.4: Product: Broadcom Bluetooth Device
[ 4.611436] usb 1-1.4: Manufacturer: Broadcom Corp
[ 4.611438] usb 1-1.4: SerialNumber: 00271396AABE
[ 4.611573] usb 1-1.4: usb_probe_device
[ 4.611578] usb 1-1.4: configuration #1 chosen from 1 choice
[ 4.611824] usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0)
[ 4.611947] usb 1-1.4: adding 1-1.4:1.1 (config #1, interface 1)
[ 4.612052] usb 1-1.4: adding 1-1.4:1.2 (config #1, interface 2)
[ 4.612141] usb 1-1.4: adding 1-1.4:1.3 (config #1, interface 3)
[ 4.612180] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '003'
[ 4.612437] hub 1-1:1.0: port 5, status 0101, change 0000, 12 Mb/s
[ 4.613119] microcode: CPU2 updated to revision 0xc, date = 2010-06-10
[ 4.613592] microcode: CPU3 updated to revision 0xc, date = 2010-06-10
[ 4.615103] cfg80211: World regulatory domain updated:
[ 4.615106] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 4.615110] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.615130] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 4.615133] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 4.615136] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.615138] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.623844] hub 1-1:1.0: port 5 not reset yet, waiting 10ms
[ 4.686830] usb 1-1.5: new high speed USB device using ehci_hcd and address 4
[ 4.695378] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:26:2d:fd:13:45
[ 4.695383] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 4.695460] e1000e 0000:00:19.0: eth0: MAC: 9, PHY: 10, PBA No: A002FF-0FF
[ 4.707799] Bluetooth: Core ver 2.15
[ 4.707830] NET: Registered protocol family 31
[ 4.707833] Bluetooth: HCI device and connection manager initialized
[ 4.707836] Bluetooth: HCI socket layer initialized
[ 4.743570] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 4.743595] btusb 1-1.4:1.0: usb_probe_interface
[ 4.743599] btusb 1-1.4:1.0: usb_probe_interface - got id
[ 4.745172] btusb 1-1.4:1.2: usb_probe_interface
[ 4.745175] btusb 1-1.4:1.2: usb_probe_interface - got id
[ 4.745187] btusb 1-1.4:1.3: usb_probe_interface
[ 4.745189] btusb 1-1.4:1.3: usb_probe_interface - got id
[ 4.745404] usbcore: registered new interface driver btusb
[ 4.758702] readahead-collector: finished
[ 4.762001] HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 4.762139] HDA Intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[ 4.762173] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 4.768055] usb 1-1.5: udev 4, busnum 1, minor = 3
[ 4.768058] usb 1-1.5: New USB device found, idVendor=17ef, idProduct=1005
[ 4.768061] usb 1-1.5: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.768169] usb 1-1.5: usb_probe_device
[ 4.768174] usb 1-1.5: configuration #1 chosen from 1 choice
[ 4.768285] usb 1-1.5: adding 1-1.5:1.0 (config #1, interface 0)
[ 4.768330] hub 1-1.5:1.0: usb_probe_interface
[ 4.768333] hub 1-1.5:1.0: usb_probe_interface - got id
[ 4.768336] hub 1-1.5:1.0: USB hub found
[ 4.768399] hub 1-1.5:1.0: 4 ports detected
[ 4.768401] hub 1-1.5:1.0: standalone hub
[ 4.768403] hub 1-1.5:1.0: individual port power switching
[ 4.768405] hub 1-1.5:1.0: individual port over-current protection
[ 4.768694] hub 1-1.5:1.0: TT per port
[ 4.768696] hub 1-1.5:1.0: TT requires at most 8 FS bit times (666 ns)
[ 4.768699] hub 1-1.5:1.0: power on to power good time: 100ms
[ 4.768900] hub 1-1.5:1.0: local power source is good
[ 4.768902] hub 1-1.5:1.0: enabling power on all ports
[ 4.769402] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '004'
[ 4.769429] hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000
[ 4.769435] hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0010
[ 4.848578] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:d
[ 4.848581] iwlagn: Copyright(c) 2003-2010 Intel Corporation
[ 4.848655] iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.848665] iwlagn 0000:02:00.0: setting latency timer to 64
[ 4.848723] iwlagn 0000:02:00.0: Detected Intel(R) Centrino(R) Ultimate-N 6300 AGN, REV=0x74
[ 4.865407] iwlagn 0000:02:00.0: device EEPROM VER=0x436, CALIB=0x6
[ 4.865413] iwlagn 0000:02:00.0: Device SKU: 0Xb
[ 4.865417] iwlagn 0000:02:00.0: Valid Tx ant: 0X7, Valid Rx ant: 0X7
[ 4.865458] iwlagn 0000:02:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
[ 4.865555] iwlagn 0000:02:00.0: irq 44 for MSI/MSI-X
[ 4.869025] hub 1-1.5:1.0: port 3: status 0301 change 0001
[ 4.872655] iwlagn 0000:02:00.0: loaded firmware version 9.221.4.1 build 25532
[ 4.886907] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 4.892411] cfg80211: Calling CRDA for country: US
[ 4.894589] cfg80211: Regulatory domain changed to country: US
[ 4.894592] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 4.894594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 4.894597] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 4.894599] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.894601] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.894603] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.894605] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 4.968599] usb 1-1.5: link qh256-0001/ffff8802329aa100 start 2 [1/0 us]
[ 4.968627] hub 1-1.5:1.0: state 7 ports 4 chg 0008 evt 0000
[ 4.968784] hub 1-1.5:1.0: port 3, status 0301, change 0000, 1.5 Mb/s
[ 4.979766] hub 1-1.5:1.0: port 3 not reset yet, waiting 10ms
[ 5.041767] usb 1-1.5.3: new low speed USB device using ehci_hcd and address 5
[ 5.053776] hub 1-1.5:1.0: port 3 not reset yet, waiting 10ms
[ 5.072998] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[ 5.091231] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input5
[ 5.130671] usb 1-1.5.3: skipped 1 descriptor after interface
[ 5.130678] usb 1-1.5.3: skipped 1 descriptor after interface
[ 5.131170] usb 1-1.5.3: default language 0x0409
[ 5.133171] usb 1-1.5.3: udev 5, busnum 1, minor = 4
[ 5.133176] usb 1-1.5.3: New USB device found, idVendor=046d, idProduct=c517
[ 5.133181] usb 1-1.5.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.133185] usb 1-1.5.3: Product: USB Receiver
[ 5.133189] usb 1-1.5.3: Manufacturer: Logitech
[ 5.133340] usb 1-1.5.3: usb_probe_device
[ 5.133344] usb 1-1.5.3: configuration #1 chosen from 1 choice
[ 5.133902] usb 1-1.5.3: adding 1-1.5.3:1.0 (config #1, interface 0)
[ 5.133968] usbhid 1-1.5.3:1.0: usb_probe_interface
[ 5.133971] usbhid 1-1.5.3:1.0: usb_probe_interface - got id
[ 5.146652] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5.3/1-1.5.3:1.0/input/input6
[ 5.146711] usb 1-1.5.3: link qh8-0e01/ffff880231d1a700 start 3 [1/2 us]
[ 5.146903] logitech 0003:046D:C517.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1a.0-1.5.3/input0
[ 5.146964] usb 1-1.5.3: adding 1-1.5.3:1.1 (config #1, interface 1)
[ 5.147032] usbhid 1-1.5.3:1.1: usb_probe_interface
[ 5.147038] usbhid 1-1.5.3:1.1: usb_probe_interface - got id
[ 5.151916] logitech 0003:046D:C517.0002: fixing up Logitech keyboard report descriptor
[ 5.152679] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5.3/1-1.5.3:1.1/input/input7
[ 5.152714] usb 1-1.5.3: link qh8-0e01/ffff8802329aaf00 start 4 [1/2 us]
[ 5.152869] usbhid 1-1.5.3:1.1: looking for a minor, starting at 96
[ 5.152950] logitech 0003:046D:C517.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1a.0-1.5.3/input1
[ 5.152971] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '005'
[ 5.153018] hub 1-1.5:1.0: state 7 ports 4 chg 0000 evt 000c
[ 5.153247] hub 1-1.5:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
[ 5.256651] hub 1-1.5:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
[ 5.267647] hub 1-1.5:1.0: port 2 not reset yet, waiting 10ms
[ 5.329643] usb 1-1.5.2: new low speed USB device using ehci_hcd and address 6
[ 5.342635] hub 1-1.5:1.0: port 2 not reset yet, waiting 10ms
[ 5.423714] usb 1-1.5.2: skipped 1 descriptor after interface
[ 5.425960] usb 1-1.5.2: default language 0x0409
[ 5.432233] usb 1-1.5.2: udev 6, busnum 1, minor = 5
[ 5.432238] usb 1-1.5.2: New USB device found, idVendor=045e, idProduct=0024
[ 5.432242] usb 1-1.5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.432246] usb 1-1.5.2: Product: Microsoft Trackball Explorer®
[ 5.432249] usb 1-1.5.2: Manufacturer: Microsoft
[ 5.432439] usb 1-1.5.2: usb_probe_device
[ 5.432445] usb 1-1.5.2: configuration #1 chosen from 1 choice
[ 5.433151] usb 1-1.5.2: adding 1-1.5.2:1.0 (config #1, interface 0)
[ 5.433247] usbhid 1-1.5.2:1.0: usb_probe_interface
[ 5.433252] usbhid 1-1.5.2:1.0: usb_probe_interface - got id
[ 5.439479] input: Microsoft Microsoft Trackball Explorer® as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5.2/1-1.5.2:1.0/input/input8
[ 5.439737] generic-usb 0003:045E:0024.0003: input,hidraw2: USB HID v1.00 Mouse [Microsoft Microsoft Trackball Explorer®] on usb-0000:00:1a.0-1.5.2/input0
[ 5.439798] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '006'
[ 6.943804] hub 2-1:1.0: hub_suspend
[ 6.943819] usb 2-1: unlink qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 6.944062] usb 2-1: usb auto-suspend
[ 6.951941] usb 1-1.4: usb auto-suspend
[ 8.953849] hub 2-0:1.0: hub_suspend
[ 8.953862] usb usb2: bus auto-suspend
[ 8.953867] ehci_hcd 0000:00:1d.0: suspend root hub
[ 10.326435] padlock_aes: VIA PadLock not detected.
[ 10.651064] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 10.651640] device fsid bd472ced4ab38dca-60668af8a13a3288 devid 1 transid 577 /dev/mapper/luks-52a5d32c-b034-4aaa-9fbc-242c46b4c9a0
[ 11.174456] Adding 6143996k swap on /dev/sda3. Priority:-1 extents:1 across:6143996k SS
[ 11.392409] NET: Registered protocol family 10
[ 11.406804] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.176823] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X
[ 12.227543] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X
[ 12.229461] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.260319] RPC: Registered udp transport module.
[ 12.260322] RPC: Registered tcp transport module.
[ 12.260323] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 12.544607] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.703700] usb 1-1.5.2: link qh8-0e01/ffff88022b189f80 start 5 [1/2 us]
[ 12.703757] usb 1-1.5.2: unlink qh8-0e01/ffff88022b189f80 start 5 [1/2 us]
[ 13.452415] Bluetooth: L2CAP ver 2.15
[ 13.452419] Bluetooth: L2CAP socket layer initialized
[ 13.463615] Bluetooth: SCO (Voice Link) ver 0.6
[ 13.463618] Bluetooth: SCO socket layer initialized
[ 13.464491] usb 1-1.4: usb auto-resume
[ 13.472690] sshd (1380): /proc/1380/oom_adj is deprecated, please use /proc/1380/oom_score_adj instead.
[ 13.501151] usb 1-1.4: finish resume
[ 13.501593] usb 1-1.4: link qh1-0e01/ffff880231d1a800 start 0 [1/2 us]
[ 13.552702] Bluetooth: RFCOMM socket layer initialized
[ 13.552706] Bluetooth: RFCOMM ver 1.11
[ 13.802801] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 13.802812] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 13.807376] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.405258] ehci_hcd 0000:00:1a.0: reused qh ffff88022b189f80 schedule
[ 15.405267] usb 1-1.5.2: link qh8-0e01/ffff88022b189f80 start 5 [1/2 us]
[ 15.939910] usb 1-1.4: unlink qh1-0e01/ffff880231d1a800 start 0 [1/2 us]
[ 15.940181] usb 1-1: clear tt buffer port 4, a3 ep2 t04048dc2
[ 15.940442] usb 1-1.4: usb auto-suspend
[ 24.090471] eth0: no IPv6 routers present
[ 27.715160] fuse init (API version 7.16)
[ 42.437868] hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0010
[ 42.438172] hub 1-1:1.0: port 4, status 0100, change 0001, 12 Mb/s
[ 42.438270] usb 1-1.4: USB disconnect, address 3
[ 42.438273] usb 1-1.4: unregistering device
[ 42.438276] usb 1-1.4: unregistering interface 1-1.4:1.0
[ 42.654990] PM: Syncing filesystems ... done.
[ 42.665477] PM: Preparing system for mem sleep
[ 42.678541] usb 1-1.5.2: unlink qh8-0e01/ffff88022b189f80 start 5 [1/2 us]
[ 42.688564] usb 1-1.4: unregistering interface 1-1.4:1.1
[ 42.688622] usb 1-1.4: unregistering interface 1-1.4:1.2
[ 42.688679] usb 1-1.4: unregistering interface 1-1.4:1.3
[ 42.688708] usb 1-1.4: usb_disable_device nuking all URBs
[ 42.783586] Freezing user space processes ...
[ 42.792568] hub 1-1:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
[ 42.795364] (elapsed 0.01 seconds) done.
[ 42.795368] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 42.806398] PM: Entering mem sleep
[ 42.806530] Suspending console(s) (use no_console_suspend to debug)
[ 42.806937] usb 1-1.5.3: unlink qh8-0e01/ffff8802329aaf00 start 4 [1/2 us]
[ 42.806949] usb 1-1.5.3: unlink qh8-0e01/ffff880231d1a700 start 3 [1/2 us]
[ 42.806998] usb 1-1.5.2: usb suspend
[ 42.807398] usb 1-1.5.3: usb suspend
[ 42.807648] usb usb2: usb auto-resume
[ 42.807656] ehci_hcd 0000:00:1d.0: resume root hub
[ 42.807791] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 42.808662] sd 0:0:0:0: [sda] Stopping disk
[ 42.818358] hub 1-1.5:1.0: hub_suspend
[ 42.818372] usb 1-1.5: unlink qh256-0001/ffff8802329aa100 start 2 [1/0 us]
[ 42.818694] usb 1-1.5: usb suspend
[ 42.827323] hub 2-0:1.0: hub_resume
[ 42.827339] hub 2-0:1.0: port 1: status 0507 change 0000
[ 42.827362] usb 2-1: usb auto-resume
[ 42.829426] hub 1-1:1.0: hub_suspend
[ 42.829435] usb 1-1: unlink qh256-0001/ffff880230a65480 start 1 [1/0 us]
[ 42.829510] usb 1-1: usb suspend
[ 42.840405] hub 1-0:1.0: hub_suspend
[ 42.840415] usb usb1: bus suspend
[ 42.840418] ehci_hcd 0000:00:1a.0: suspend root hub
[ 42.853448] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 42.864384] usb 2-1: finish resume
[ 42.864637] hub 2-1:1.0: hub_resume
[ 42.865615] ehci_hcd 0000:00:1d.0: reused qh ffff880230be8600 schedule
[ 42.865623] usb 2-1: link qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 42.865634] hub 2-1:1.0: hub_suspend
[ 42.865642] usb 2-1: unlink qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 42.865715] usb 2-1: usb suspend
[ 42.876450] hub 2-0:1.0: hub_suspend
[ 42.876458] usb usb2: bus suspend
[ 42.876461] ehci_hcd 0000:00:1d.0: suspend root hub
[ 42.999528] ehci_hcd 0000:00:1d.0: PCI INT D disabled
[ 42.999556] ehci_hcd 0000:00:1a.0: PCI INT D disabled
[ 43.014233] i915 0000:00:02.0: power state changed by ACPI to D3
[ 43.105681] e1000e 0000:00:19.0: PCI INT A disabled
[ 43.105688] e1000e 0000:00:19.0: PME# enabled
[ 43.105696] e1000e 0000:00:19.0: wake-up capability enabled by ACPI
[ 44.201813] HDA Intel 0000:00:1b.0: PCI INT B disabled
[ 44.212882] PM: suspend of devices complete after 1406.690 msecs
[ 44.224007] ehci_hcd 0000:00:1d.0: wakeup: 0
[ 44.234801] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D3
[ 44.234807] ehci_hcd 0000:00:1d.0: --> PCI D3hot
[ 44.234850] ehci_hcd 0000:00:1a.0: wakeup: 0
[ 44.250735] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D3
[ 44.250742] ehci_hcd 0000:00:1a.0: --> PCI D3hot
[ 44.250879] PM: late suspend of devices complete after 38.009 msecs
[ 44.251098] ACPI: Preparing to enter system sleep state S3
[ 44.303802] PM: Saving platform NVS memory
[ 44.308938] Disabling non-boot CPUs ...
[ 44.310802] CPU 1 is now offline
[ 44.324125] CPU 2 is now offline
[ 44.331839] Broke affinity for irq 9
[ 44.332886] CPU 3 is now offline
[ 44.333950] Extended CMOS year: 2000
[ 44.334292] Back to C!
[ 44.334295] PM: Restoring platform NVS memory
[ 44.334960] microcode: CPU0 updated to revision 0xc, date = 2010-06-10
[ 44.335258] Extended CMOS year: 2000
[ 44.335309] Enabling non-boot CPUs ...
[ 44.335410] Booting Node 0 Processor 1 APIC 0x1
[ 44.426948] Switched to NOHz mode on CPU #1
[ 44.428117] NMI watchdog enabled, takes one hw-pmu counter.
[ 44.428484] microcode: CPU1 updated to revision 0xc, date = 2010-06-10
[ 44.436057] CPU1 is up
[ 44.436144] Booting Node 0 Processor 2 APIC 0x4
[ 44.527182] NMI watchdog enabled, takes one hw-pmu counter.
[ 44.527558] microcode: CPU2 updated to revision 0xc, date = 2010-06-10
[ 44.527869] Switched to NOHz mode on CPU #2
[ 44.535025] CPU2 is up
[ 44.535107] Booting Node 0 Processor 3 APIC 0x5
[ 44.626102] NMI watchdog enabled, takes one hw-pmu counter.
[ 44.626844] microcode: CPU3 updated to revision 0xc, date = 2010-06-10
[ 44.626854] Switched to NOHz mode on CPU #3
[ 44.635095] CPU3 is up
[ 44.636672] ACPI: Waking up from system sleep state S3
[ 44.683900] intel ips 0000:00:1f.6: MCP limit exceeded: Avg temp 20777, limit 9000
[ 44.716003] agpgart-intel 0000:00:00.0: restoring config space at offset 0x1 (was 0x900006, writing 0x20900006)
[ 44.716017] i915 0000:00:02.0: restoring config space at offset 0x1 (was 0x900007, writing 0x900407)
[ 44.716098] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100103, writing 0x100107)
[ 44.716128] ehci_hcd 0000:00:1a.0: restoring config space at offset 0xf (was 0x400, writing 0x40b)
[ 44.716146] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x4 (was 0x0, writing 0xf2728000)
[ 44.716154] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
[ 44.720851] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 44.720861] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 44.720965] pcieport 0000:00:1c.0: restoring config space at offset 0x7 (was 0xf0, writing 0x200000f0)
[ 44.721070] pcieport 0000:00:1c.4: restoring config space at offset 0xf (was 0x100, writing 0x4010b)
[ 44.721081] pcieport 0000:00:1c.4: restoring config space at offset 0x9 (was 0x10001, writing 0x1fff1)
[ 44.721086] pcieport 0000:00:1c.4: restoring config space at offset 0x8 (was 0x0, writing 0xf240f240)
[ 44.721091] pcieport 0000:00:1c.4: restoring config space at offset 0x7 (was 0x0, writing 0x200000f0)
[ 44.721099] pcieport 0000:00:1c.4: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
[ 44.721105] pcieport 0000:00:1c.4: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[ 44.721139] ehci_hcd 0000:00:1d.0: restoring config space at offset 0xf (was 0x400, writing 0x40b)
[ 44.721157] ehci_hcd 0000:00:1d.0: restoring config space at offset 0x4 (was 0x0, writing 0xf2728400)
[ 44.721165] ehci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
[ 44.721183] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 44.721186] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 44.721290] ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
[ 44.721356] intel ips 0000:00:1f.6: restoring config space at offset 0xf (was 0x400, writing 0x40b)
[ 44.721378] intel ips 0000:00:1f.6: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
[ 44.721596] PM: early resume of devices complete after 5.721 msecs
[ 44.721725] i915 0000:00:02.0: power state changed by ACPI to D0
[ 44.721729] i915 0000:00:02.0: power state changed by ACPI to D0
[ 44.721734] i915 0000:00:02.0: setting latency timer to 64
[ 44.721837] e1000e 0000:00:19.0: wake-up capability disabled by ACPI
[ 44.721846] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 44.721848] e1000e 0000:00:19.0: PME# disabled
[ 44.721860] HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 44.721872] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 44.721956] HDA Intel 0000:00:1b.0: irq 42 for MSI/MSI-X
[ 44.722040] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 44.722882] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 44.722890] ehci_hcd 0000:00:1a.0: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 44.722897] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 44.722928] usb usb1: usb resume
[ 44.722932] ehci_hcd 0000:00:1a.0: resume root hub
[ 44.722956] pci 0000:00:1e.0: setting latency timer to 64
[ 44.722971] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 44.722990] ahci 0000:00:1f.2: setting latency timer to 64
[ 44.723133] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 44.723143] ehci_hcd 0000:00:1d.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 44.723156] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 44.723192] sd 0:0:0:0: [sda] Starting disk
[ 44.723200] usb usb2: usb resume
[ 44.723204] ehci_hcd 0000:00:1d.0: resume root hub
[ 44.742799] hub 1-0:1.0: hub_resume
[ 44.742802] hub 2-0:1.0: hub_resume
[ 44.742814] hub 2-0:1.0: port 1: status 0507 change 0000
[ 44.742816] hub 1-0:1.0: port 1: status 0507 change 0000
[ 44.742847] usb 2-1: usb resume
[ 44.742857] usb 1-1: usb resume
[ 44.758857] legacy_resume(): pnp_bus_resume+0x0/0x6c returns -19
[ 44.758859] PM: Device 00:0c failed to resume: error -19
[ 44.768822] ehci_hcd 0000:00:1a.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 44.768825] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 44.779791] usb 1-1: finish resume
[ 44.779793] usb 2-1: finish resume
[ 44.779970] hub 2-1:1.0: hub_resume
[ 44.779981] hub 1-1:1.0: hub_resume
[ 44.780607] hub 1-1:1.0: port 5: status 0507 change 0000
[ 44.780712] ehci_hcd 0000:00:1a.0: reused qh ffff880230a65480 schedule
[ 44.780715] usb 1-1: link qh256-0001/ffff880230a65480 start 1 [1/0 us]
[ 44.780964] usb 1-1.5: usb resume
[ 44.780975] ehci_hcd 0000:00:1d.0: reused qh ffff880230be8600 schedule
[ 44.780978] usb 2-1: link qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 44.817951] usb 1-1.5: finish resume
[ 44.818076] hub 1-1.5:1.0: hub_resume
[ 44.818331] hub 1-1.5:1.0: port 2: status 0307 change 0000
[ 44.818452] hub 1-1.5:1.0: port 3: status 0307 change 0000
[ 44.818579] ehci_hcd 0000:00:1a.0: reused qh ffff8802329aa100 schedule
[ 44.818582] usb 1-1.5: link qh256-0001/ffff8802329aa100 start 2 [1/0 us]
[ 44.818826] usb 1-1.5.2: usb resume
[ 44.818951] usb 1-1.5.3: usb resume
[ 44.855935] usb 1-1.5.2: finish resume
[ 44.855938] usb 1-1.5.3: finish resume
[ 44.856830] ehci_hcd 0000:00:1a.0: reused qh ffff880231d1a700 schedule
[ 44.856834] usb 1-1.5.3: link qh8-0e01/ffff880231d1a700 start 3 [1/2 us]
[ 44.856850] ehci_hcd 0000:00:1a.0: reused qh ffff8802329aaf00 schedule
[ 44.856852] usb 1-1.5.3: link qh8-0e01/ffff8802329aaf00 start 4 [1/2 us]
[ 45.029759] ata2: SATA link down (SStatus 0 SControl 300)
[ 45.031762] ata6: SATA link down (SStatus 0 SControl 300)
[ 45.033757] ata5: SATA link down (SStatus 0 SControl 300)
[ 45.094625] No ACPI video bus found
[ 45.947359] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 46.174426] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 46.174433] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 46.174439] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 46.904565] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 46.904572] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 46.904578] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 47.228822] ata1.00: configured for UDMA/100
[ 47.434268] PM: resume of devices complete after 2713.775 msecs
[ 47.434475] PM: Finishing wakeup.
[ 47.434477] Restarting tasks ...
[ 47.434524] hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 47.434530] hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000
[ 47.434537] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 47.434541] hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0000
[ 47.434546] hub 1-1.5:1.0: state 7 ports 4 chg 0000 evt 0000
[ 47.443448] done.
[ 47.641377] ehci_hcd 0000:00:1a.0: reused qh ffff88022b189f80 schedule
[ 47.641381] usb 1-1.5.2: link qh8-0e01/ffff88022b189f80 start 5 [1/2 us]
[ 48.904301] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 48.955124] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 48.958418] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 49.063358] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 49.074202] hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0010
[ 49.074548] hub 1-1:1.0: port 4, status 0101, change 0001, 12 Mb/s
[ 49.179013] hub 1-1:1.0: debounce: port 4: total 100ms stable 100ms status 0x101
[ 49.241982] usb 1-1.4: new full speed USB device using ehci_hcd and address 7
[ 49.252987] hub 1-1:1.0: port 4 not reset yet, waiting 10ms
[ 49.329854] usb 1-1.4: skipped 1 descriptor after interface
[ 49.330195] usb 1-1.4: default language 0x0409
[ 49.331320] usb 1-1.4: udev 7, busnum 1, minor = 6
[ 49.331327] usb 1-1.4: New USB device found, idVendor=0a5c, idProduct=217f
[ 49.331335] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 49.331341] usb 1-1.4: Product: Broadcom Bluetooth Device
[ 49.331347] usb 1-1.4: Manufacturer: Broadcom Corp
[ 49.331351] usb 1-1.4: SerialNumber: 00271396AABE
[ 49.331584] usb 1-1.4: usb_probe_device
[ 49.331592] usb 1-1.4: configuration #1 chosen from 1 choice
[ 49.331829] usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0)
[ 49.331936] btusb 1-1.4:1.0: usb_probe_interface
[ 49.331942] btusb 1-1.4:1.0: usb_probe_interface - got id
[ 49.332461] usb 1-1.4: adding 1-1.4:1.1 (config #1, interface 1)
[ 49.332637] usb 1-1.4: adding 1-1.4:1.2 (config #1, interface 2)
[ 49.332720] btusb 1-1.4:1.2: usb_probe_interface
[ 49.332726] btusb 1-1.4:1.2: usb_probe_interface - got id
[ 49.332851] usb 1-1.4: adding 1-1.4:1.3 (config #1, interface 3)
[ 49.332939] btusb 1-1.4:1.3: usb_probe_interface
[ 49.332945] btusb 1-1.4:1.3: usb_probe_interface - got id
[ 49.332961] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '007'
[ 49.333431] usb 1-1.4: link qh1-0e01/ffff88020cebc480 start 0 [1/2 us]
[ 49.934658] hub 2-1:1.0: hub_suspend
[ 49.934671] usb 2-1: unlink qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 49.934922] usb 2-1: usb auto-suspend
[ 50.543368] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 50.543375] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 50.546463] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 51.933834] usb 1-1.4: unlink qh1-0e01/ffff88020cebc480 start 0 [1/2 us]
[ 51.934097] usb 1-1: clear tt buffer port 4, a7 ep2 t04048dc2
[ 51.934464] usb 1-1.4: usb auto-suspend
[ 51.944774] hub 2-0:1.0: hub_suspend
[ 51.944785] usb usb2: bus auto-suspend
[ 51.944790] ehci_hcd 0000:00:1d.0: suspend root hub
[ 57.752704] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.753640] ehci_hcd 0000:00:1a.0: detected XactErr len 0/20 retry 1
[ 57.754662] ehci_hcd 0000:00:1a.0: detected XactErr len 0/4 retry 1
[ 57.760590] usb 1-1.5.3: unlink qh8-0e01/ffff880231d1a700 start 3 [1/2 us]
[ 57.760768] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.760911] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 2
[ 57.761026] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 3
[ 57.761152] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 4
[ 57.761274] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 5
[ 57.761385] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 6
[ 57.761400] usb 1-1.5.3: unlink qh8-0e01/ffff8802329aaf00 start 4 [1/2 us]
[ 57.761490] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 7
[ 57.761633] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 8
[ 57.761762] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 9
[ 57.761857] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 10
[ 57.761977] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 11
[ 57.762103] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 12
[ 57.762261] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 13
[ 57.762372] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 14
[ 57.762388] usb 1-1.5.2: unlink qh8-0e01/ffff88022b189f80 start 5 [1/2 us]
[ 57.762483] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 15
[ 57.762638] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.762643] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 16
[ 57.762728] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 2
[ 57.762733] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 17
[ 57.762855] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 3
[ 57.762860] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 18
[ 57.762981] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 4
[ 57.762985] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 19
[ 57.763101] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 5
[ 57.763106] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 20
[ 57.763268] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 6
[ 57.763272] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 21
[ 57.763398] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 7
[ 57.763403] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 22
[ 57.763520] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 8
[ 57.763525] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 23
[ 57.763589] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 9
[ 57.763593] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 24
[ 57.763727] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 10
[ 57.763732] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 25
[ 57.763853] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 11
[ 57.763858] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 26
[ 57.763979] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 12
[ 57.763983] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 27
[ 57.764104] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 13
[ 57.764108] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 28
[ 57.764257] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 14
[ 57.764263] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 29
[ 57.764373] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 15
[ 57.764378] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 30
[ 57.764500] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 16
[ 57.764505] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 31
[ 57.764605] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 17
[ 57.764609] ehci_hcd 0000:00:1a.0: devpath 1.5.3 ep0out 3strikes
[ 57.764615] usb 1-1.5: clear tt buffer port 3, a5 ep0 t00080248
[ 57.764666] ehci_hcd 0000:00:1a.0: reused qh ffff880231d1a700 schedule
[ 57.764672] usb 1-1.5.3: link qh8-0e01/ffff880231d1a700 start 3 [1/2 us]
[ 57.764680] logitech 0003:046D:C517.0001: can't reset device, 0000:00:1a.0-1.5.3/input0, status -71
[ 57.764725] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.764730] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 18
[ 57.764852] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 2
[ 57.764857] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 19
[ 57.764978] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 3
[ 57.764983] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 20
[ 57.765104] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 4
[ 57.765109] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 21
[ 57.765227] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 5
[ 57.765231] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 22
[ 57.765351] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 6
[ 57.765356] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 23
[ 57.765474] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 7
[ 57.765478] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 24
[ 57.765588] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 8
[ 57.765593] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 25
[ 57.765714] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 9
[ 57.765719] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 26
[ 57.765856] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 10
[ 57.765860] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 27
[ 57.765977] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 11
[ 57.765981] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 28
[ 57.766102] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 12
[ 57.766107] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 29
[ 57.766257] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 13
[ 57.766262] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 30
[ 57.766374] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 14
[ 57.766379] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 31
[ 57.766477] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 15
[ 57.766481] ehci_hcd 0000:00:1a.0: devpath 1.5.2 ep0out 3strikes
[ 57.766486] usb 1-1.5: clear tt buffer port 2, a6 ep0 t00080248
[ 57.766534] ehci_hcd 0000:00:1a.0: reused qh ffff88022b189f80 schedule
[ 57.766540] usb 1-1.5.2: link qh8-0e01/ffff88022b189f80 start 5 [1/2 us]
[ 57.766548] generic-usb 0003:045E:0024.0003: can't reset device, 0000:00:1a.0-1.5.2/input0, status -71
[ 57.766604] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 16
[ 57.766728] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 17
[ 57.766854] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 18
[ 57.766980] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 19
[ 57.767100] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 20
[ 57.767228] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 21
[ 57.767351] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 22
[ 57.767463] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 23
[ 57.767606] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 24
[ 57.767726] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 25
[ 57.767851] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 26
[ 57.767977] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 27
[ 57.768104] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 28
[ 57.768258] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 29
[ 57.768379] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 30
[ 57.768476] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 31
[ 57.768482] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.768602] ehci_hcd 0000:00:1a.0: devpath 1.5 ep0out 3strikes
[ 57.768624] usb 1-1.5: clear tt 3 (0050) error -71
[ 57.768730] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.768743] usb 1-1.5.3: unlink qh8-0e01/ffff880231d1a700 start 3 [1/2 us]
[ 57.768854] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.768859] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 2
[ 57.768975] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 2
[ 57.768980] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 3
[ 57.769101] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 3
[ 57.769106] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 4
[ 57.769223] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 4
[ 57.769228] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 5
[ 57.769351] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 5
[ 57.769355] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 6
[ 57.769462] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 6
[ 57.769467] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 7
[ 57.769602] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 7
[ 57.769607] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 8
[ 57.769726] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 8
[ 57.769731] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 9
[ 57.769853] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 9
[ 57.769857] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 10
[ 57.769975] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 10
[ 57.769979] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 11
[ 57.770101] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 11
[ 57.770105] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 12
[ 57.770259] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 12
[ 57.770265] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 13
[ 57.770371] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 13
[ 57.770376] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 14
[ 57.770477] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 14
[ 57.770481] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 15
[ 57.770487] ehci_hcd 0000:00:1a.0: detected XactErr len 0/4 retry 1
[ 57.770599] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 15
[ 57.770604] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 16
[ 57.770726] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 16
[ 57.770730] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 17
[ 57.770745] usb 1-1.5.2: unlink qh8-0e01/ffff88022b189f80 start 5 [1/2 us]
[ 57.770836] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 17
[ 57.770841] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 18
[ 57.770978] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 18
[ 57.770983] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 19
[ 57.771098] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 19
[ 57.771102] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 20
[ 57.771232] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 20
[ 57.771236] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 21
[ 57.771350] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 21
[ 57.771355] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 22
[ 57.771474] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 22
[ 57.771478] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 23
[ 57.771586] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 23
[ 57.771591] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 24
[ 57.771712] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 24
[ 57.771717] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 25
[ 57.771853] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 25
[ 57.771858] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 26
[ 57.771974] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 26
[ 57.771979] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 27
[ 57.772100] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 27
[ 57.772105] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 28
[ 57.772225] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 28
[ 57.772229] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 29
[ 57.772342] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 29
[ 57.772347] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 30
[ 57.772503] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 30
[ 57.772509] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 31
[ 57.772597] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 31
[ 57.772602] ehci_hcd 0000:00:1a.0: devpath 1.5.3 ep0out 3strikes
[ 57.772607] usb 1-1.5: clear tt buffer port 3, a5 ep0 t00080248
[ 57.772654] ehci_hcd 0000:00:1a.0: reused qh ffff8802329aaf00 schedule
[ 57.772660] usb 1-1.5.3: link qh8-0e01/ffff8802329aaf00 start 4 [1/2 us]
[ 57.772668] logitech 0003:046D:C517.0002: can't reset device, 0000:00:1a.0-1.5.3/input1, status -71
[ 57.772730] ehci_hcd 0000:00:1a.0: devpath 1.5 ep0out 3strikes
[ 57.772748] usb 1-1.5: clear tt 2 (0060) error -71
[ 57.772850] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.772975] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.772980] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 2
[ 57.773101] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 2
[ 57.773105] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 3
[ 57.773229] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 3
[ 57.773233] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 4
[ 57.773346] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 4
[ 57.773351] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 5
[ 57.773462] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 5
[ 57.773467] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 6
[ 57.773600] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 6
[ 57.773604] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 7
[ 57.773724] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 7
[ 57.773728] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 8
[ 57.773850] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 8
[ 57.773854] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 9
[ 57.773976] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 9
[ 57.773980] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 10
[ 57.774102] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 10
[ 57.774107] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 11
[ 57.774230] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 11
[ 57.774235] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 12
[ 57.774335] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 12
[ 57.774339] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 13
[ 57.774365] hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0020
[ 57.774472] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 13
[ 57.774477] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 14
[ 57.774603] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 14
[ 57.774608] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 15
[ 57.774620] hub 1-1:1.0: port 5, status 0100, change 0001, 12 Mb/s
[ 57.774728] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 15
[ 57.774732] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 16
[ 57.774743] usb 1-1.5: USB disconnect, address 4
[ 57.774747] usb 1-1.5.2: USB disconnect, address 6
[ 57.774750] usb 1-1.5.2: unregistering device
[ 57.774754] usb 1-1.5.2: unregistering interface 1-1.5.2:1.0
[ 57.774847] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 16
[ 57.774852] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 17
[ 57.774959] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 17
[ 57.774964] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 18
[ 57.775088] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 18
[ 57.775095] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 19
[ 57.775212] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 19
[ 57.775217] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 20
[ 57.775333] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 20
[ 57.775338] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 21
[ 57.775460] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 21
[ 57.775464] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 22
[ 57.775585] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 22
[ 57.775590] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 23
[ 57.775708] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 23
[ 57.775712] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 24
[ 57.775837] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 24
[ 57.775845] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 25
[ 57.775978] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 25
[ 57.775983] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 26
[ 57.776098] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 26
[ 57.776103] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 27
[ 57.776209] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 27
[ 57.776214] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 28
[ 57.776351] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 28
[ 57.776356] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 29
[ 57.776473] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 29
[ 57.776477] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 30
[ 57.776609] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 30
[ 57.776614] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 31
[ 57.776738] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 31
[ 57.776742] ehci_hcd 0000:00:1a.0: devpath 1.5.2 ep0out 3strikes
[ 57.776747] usb 1-1.5: clear tt buffer port 2, a6 ep0 t00080248
[ 57.776770] generic-usb 0003:045E:0024.0003: can't reset device, 0000:00:1a.0-1.5.2/input0, status -71
[ 57.776870] ehci_hcd 0000:00:1a.0: devpath 1.5 ep0out 3strikes
[ 57.776886] usb 1-1.5: clear tt 3 (0050) error -71
[ 57.776893] usb 1-1.5: clear tt 2 (0060) error -19
[ 57.776988] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 1
[ 57.777109] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 2
[ 57.777209] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 3
[ 57.777335] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 4
[ 57.777459] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 5
[ 57.777466] ehci_hcd 0000:00:1a.0: detected XactErr len 0/20 retry 1
[ 57.777601] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 6
[ 57.777722] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 7
[ 57.777736] usb 1-1.5.3: unlink qh8-0e01/ffff8802329aaf00 start 4 [1/2 us]
[ 57.777848] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 8
[ 57.777975] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 9
[ 57.778095] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 10
[ 57.778208] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 11
[ 57.778364] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 12
[ 57.778475] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 13
[ 57.778596] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 14
[ 57.778722] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 15
[ 57.778849] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 16
[ 57.778990] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 17
[ 57.779112] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 18
[ 57.779207] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 19
[ 57.779366] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 20
[ 57.779486] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 21
[ 57.779609] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 22
[ 57.779736] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 23
[ 57.779862] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 24
[ 57.779985] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 25
[ 57.780108] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 26
[ 57.780209] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 27
[ 57.780332] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 28
[ 57.780459] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 29
[ 57.780581] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 30
[ 57.780706] ehci_hcd 0000:00:1a.0: detected XactErr len 0/8 retry 31
[ 57.780848] ehci_hcd 0000:00:1a.0: devpath 1.5.3 ep0out 3strikes
[ 57.780856] usb 1-1.5: clear tt buffer port 3, a5 ep0 t00080248
[ 57.781189] logitech 0003:046D:C517.0001: can't reset device, 0000:00:1a.0-1.5.3/input0, status -71
[ 57.781200] usb 1-1.5: clear tt 3 (0050) error -19
[ 57.787439] usb 1-1.5.2: usb_disable_device nuking all URBs
[ 57.787634] usb 1-1.5.3: USB disconnect, address 5
[ 57.787641] usb 1-1.5.3: unregistering device
[ 57.787647] usb 1-1.5.3: unregistering interface 1-1.5.3:1.0
[ 57.796461] usb 1-1.5.3: unregistering interface 1-1.5.3:1.1
[ 57.815314] /home/hohndel/linux/drivers/usb/core/file.c: removing 96 minor
[ 57.815586] usb 1-1.5.3: usb_disable_device nuking all URBs
[ 57.816896] e1000e: eth0 NIC Link is Down
[ 57.820330] usb 1-1.5: unregistering device
[ 57.820335] usb 1-1.5: unregistering interface 1-1.5:1.0
[ 57.820393] usb 1-1.5: unlink qh256-0001/ffff8802329aa100 start 2 [1/0 us]
[ 57.820464] ehci_hcd 0000:00:1a.0: shutdown urb ffff880232480600 ep1in-intr
[ 57.820530] usb 1-1.5: usb_disable_device nuking all URBs
[ 57.925363] hub 1-1:1.0: debounce: port 5: total 100ms stable 100ms status 0x100
[ 58.403824] thinkpad_acpi: EC reports that Thermal Table has changed
[ 58.404982] ACPI: \_SB_.GDCK - undocking
[ 59.934306] hub 1-1:1.0: hub_suspend
[ 59.934317] usb 1-1: unlink qh256-0001/ffff880230a65480 start 1 [1/0 us]
[ 59.934442] usb 1-1: usb auto-suspend
[ 61.107802] eth0: no IPv6 routers present
[ 61.944458] hub 1-0:1.0: hub_suspend
[ 61.944472] usb usb1: bus auto-suspend
[ 61.944477] ehci_hcd 0000:00:1a.0: suspend root hub
[ 63.620732] ehci_hcd 0000:00:1a.0: port 1 remote wakeup
[ 63.620835] usb usb1: usb wakeup-resume
[ 63.620843] usb usb1: usb auto-resume
[ 63.620849] ehci_hcd 0000:00:1a.0: resume root hub
[ 63.640660] hub 1-0:1.0: hub_resume
[ 63.640679] hub 1-0:1.0: port 1: status 0507 change 0000
[ 63.640705] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 63.785917] PM: Syncing filesystems ... done.
[ 63.795661] PM: Preparing system for mem sleep
[ 64.054632] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 64.066550] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 64.077574] PM: Entering mem sleep
[ 64.077716] Suspending console(s) (use no_console_suspend to debug)
[ 64.078069] ehci_hcd 0000:00:1a.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 64.078079] usb 1-1: finish resume
[ 64.078337] hub 1-1:1.0: hub_resume
[ 64.078563] usb usb2: usb auto-resume
[ 64.078570] ehci_hcd 0000:00:1d.0: resume root hub
[ 64.078615] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 64.078847] hub 1-1:1.0: port 4: status 0100 change 0001
[ 64.079458] sd 0:0:0:0: [sda] Stopping disk
[ 64.098468] hub 2-0:1.0: hub_resume
[ 64.098482] hub 2-0:1.0: port 1: status 0507 change 0000
[ 64.098504] usb 2-1: usb auto-resume
[ 64.124549] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 64.135472] usb 2-1: finish resume
[ 64.135720] hub 2-1:1.0: hub_resume
[ 64.136726] ehci_hcd 0000:00:1d.0: reused qh ffff880230be8600 schedule
[ 64.136733] usb 2-1: link qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 64.136745] hub 2-1:1.0: hub_suspend
[ 64.136753] usb 2-1: unlink qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 64.136828] usb 2-1: usb suspend
[ 64.147527] hub 2-0:1.0: hub_suspend
[ 64.147536] usb usb2: bus suspend
[ 64.147539] ehci_hcd 0000:00:1d.0: suspend root hub
[ 64.179492] ehci_hcd 0000:00:1a.0: reused qh ffff880230a65480 schedule
[ 64.179499] usb 1-1: link qh256-0001/ffff880230a65480 start 1 [1/0 us]
[ 64.179709] hub 1-1:1.0: port 4 status 0000.0100 after resume, -19
[ 64.179714] usb 1-1.4: can't resume, status -19
[ 64.179717] hub 1-1:1.0: logical disconnect on port 4
[ 64.179854] hub 1-1:1.0: port 4 nyet suspended
[ 64.179858] hub 1-1:1.0: suspend error -16
[ 64.179869] pm_op(): usb_dev_suspend+0x0/0x15 returns -16
[ 64.179877] PM: Device 1-1 failed to suspend async: error -16
[ 64.269480] PM: Some devices failed to suspend
[ 64.269620] sd 0:0:0:0: [sda] Starting disk
[ 64.269642] hub 1-0:1.0: hub_resume
[ 64.269658] hub 1-0:1.0: port 1: status 0503 change 0000
[ 64.269676] usb usb2: usb resume
[ 64.269679] hub 1-0:1.0: activate --> -22
[ 64.269682] ehci_hcd 0000:00:1d.0: resume root hub
[ 64.269704] hub 1-1:1.0: hub_resume
[ 64.270268] hub 1-1:1.0: port 4: status 0100 change 0000
[ 64.270546] hub 1-1:1.0: activate --> -22
[ 64.287481] legacy_resume(): pnp_bus_resume+0x0/0x6c returns -19
[ 64.287486] PM: Device 00:0c failed to resume: error -19
[ 64.289364] hub 2-0:1.0: hub_resume
[ 64.289374] hub 2-0:1.0: port 1: status 0507 change 0000
[ 64.289403] usb 2-1: usb resume
[ 64.315469] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 64.326439] usb 2-1: finish resume
[ 64.326663] hub 2-1:1.0: hub_resume
[ 64.327629] ehci_hcd 0000:00:1d.0: reused qh ffff880230be8600 schedule
[ 64.327636] usb 2-1: link qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 64.327673] PM: resume of devices complete after 58.212 msecs
[ 64.327833] PM: Finishing wakeup.
[ 64.327834] Restarting tasks ...
[ 64.327865] hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 64.327872] hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000
[ 64.327880] hub 1-1:1.0: state 7 ports 6 chg 0010 evt 0000
[ 64.328757] hub 1-1:1.0: port 4, status 0100, change 0000, 12 Mb/s
[ 64.329015] usb 1-1.4: USB disconnect, address 7
[ 64.329019] usb 1-1.4: unregistering device
[ 64.329022] usb 1-1.4: unregistering interface 1-1.4:1.0
[ 64.330542] done.
[ 64.580920] usb 1-1.4: unregistering interface 1-1.4:1.1
[ 64.580994] usb 1-1.4: unregistering interface 1-1.4:1.2
[ 64.581054] usb 1-1.4: unregistering interface 1-1.4:1.3
[ 64.581085] usb 1-1.4: usb_disable_device nuking all URBs
[ 64.581237] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 64.633462] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 64.684361] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 64.687986] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 64.808259] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 64.824781] hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0010
[ 64.827314] hub 1-1:1.0: port 4, status 0101, change 0001, 12 Mb/s
[ 64.931273] hub 1-1:1.0: debounce: port 4: total 100ms stable 100ms status 0x101
[ 64.942392] hub 1-1:1.0: port 4 not reset yet, waiting 10ms
[ 65.004274] usb 1-1.4: new full speed USB device using ehci_hcd and address 8
[ 65.015208] hub 1-1:1.0: port 4 not reset yet, waiting 10ms
[ 65.092248] usb 1-1.4: skipped 1 descriptor after interface
[ 65.092572] usb 1-1.4: default language 0x0409
[ 65.093696] usb 1-1.4: udev 8, busnum 1, minor = 7
[ 65.093701] usb 1-1.4: New USB device found, idVendor=0a5c, idProduct=217f
[ 65.093706] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 65.093710] usb 1-1.4: Product: Broadcom Bluetooth Device
[ 65.093714] usb 1-1.4: Manufacturer: Broadcom Corp
[ 65.093717] usb 1-1.4: SerialNumber: 00271396AABE
[ 65.093893] usb 1-1.4: usb_probe_device
[ 65.093901] usb 1-1.4: configuration #1 chosen from 1 choice
[ 65.094629] usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0)
[ 65.094724] btusb 1-1.4:1.0: usb_probe_interface
[ 65.094730] btusb 1-1.4:1.0: usb_probe_interface - got id
[ 65.095211] usb 1-1.4: adding 1-1.4:1.1 (config #1, interface 1)
[ 65.095385] usb 1-1.4: adding 1-1.4:1.2 (config #1, interface 2)
[ 65.095465] btusb 1-1.4:1.2: usb_probe_interface
[ 65.095471] btusb 1-1.4:1.2: usb_probe_interface - got id
[ 65.095580] usb 1-1.4: adding 1-1.4:1.3 (config #1, interface 3)
[ 65.095662] btusb 1-1.4:1.3: usb_probe_interface
[ 65.095667] btusb 1-1.4:1.3: usb_probe_interface - got id
[ 65.095680] /home/hohndel/linux/drivers/usb/core/inode.c: creating file '008'
[ 65.096582] usb 1-1.4: link qh1-0e01/ffff8801f9ae1a80 start 0 [1/2 us]
[ 65.834976] notification-da[2413] general protection ip:32acc33231 sp:7fffe74e4d60 error:0 in libgobject-2.0.so.0.2600.0[32acc00000+4c000]
[ 66.927358] hub 2-1:1.0: hub_suspend
[ 66.927371] usb 2-1: unlink qh256-0001/ffff880230be8600 start 1 [1/0 us]
[ 66.927522] usb 2-1: usb auto-suspend
[ 67.168257] usb 1-1.4: unlink qh1-0e01/ffff8801f9ae1a80 start 0 [1/2 us]
[ 67.168597] usb 1-1: clear tt buffer port 4, a8 ep2 t04048dc2
[ 67.169088] usb 1-1.4: usb auto-suspend
[ 68.937441] hub 2-0:1.0: hub_suspend
[ 68.937453] usb usb2: bus auto-suspend
[ 68.937457] ehci_hcd 0000:00:1d.0: suspend root hub
[ 69.934065] hub 1-1:1.0: hub_suspend
[ 69.934078] usb 1-1: unlink qh256-0001/ffff880230a65480 start 1 [1/0 us]
[ 69.934302] usb 1-1: usb auto-suspend
[ 71.944178] hub 1-0:1.0: hub_suspend
[ 71.944191] usb usb1: bus auto-suspend
[ 71.944195] ehci_hcd 0000:00:1a.0: suspend root hub
[-- Attachment #3: devices.txt --]
[-- Type: text/plain, Size: 3275 bytes --]
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 3
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 2.06
S: Manufacturer=Linux 2.6.38-rc4-00178-g795abaf ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:1d.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 8
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0020 Rev= 0.00
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 3
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 2.06
S: Manufacturer=Linux 2.6.38-rc4-00178-g795abaf ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:1a.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 6
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0020 Rev= 0.00
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 8 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=217f Rev= 3.60
S: Manufacturer=Broadcom Corp
S: Product=Broadcom Bluetooth Device
S: SerialNumber=00271396AABE
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
[-- Attachment #4: Type: text/plain, Size: 0 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2011-02-14 21:12 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <m31v3abf1k.fsf@x201s.gr8dns.org>
2011-02-14 20:55 ` USB suspend issue with 2.6.38-rc2 -- still there in RC4-g795abaf Alan Stern
[not found] <m31v3a8i4j.fsf@x201s.gr8dns.org>
2011-02-14 21:12 ` Alan Stern
[not found] <Pine.LNX.4.44L0.1101251021310.1867-100000@iolanthe.rowland.org>
2011-02-14 19:18 ` Dirk Hohndel
[not found] ` <m38vxibfez.fsf@x201s.gr8dns.org>
[not found] ` <AANLkTik4e0UoMbtMUSsyym_y-Y-xcTzdJK26zzGk719f@mail.gmail.com>
2011-02-14 20:40 ` Dirk Hohndel
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.