* Re: sata_sil command 0x25 timeout, stat 0x50 host_stat 0x64 (fwd)
@ 2004-10-11 15:07 Johannes Peeters
2004-10-11 15:19 ` Jeff Garzik
0 siblings, 1 reply; 4+ messages in thread
From: Johannes Peeters @ 2004-10-11 15:07 UTC (permalink / raw)
To: linux-ide
Hello,
I accidentaly send this to the linux-kernel mailinlist, but i had to send
it to the linux-ide list.
I also tried noapic acpi=off pci=biosirq, but no success. Do you have any
idea what to do next?
Thanks,
Johannes Peeters
---------- Forwarded message ----------
Date: Sat, 9 Oct 2004 18:10:08 +0000 (GMT)
From: Johannes Peeters <jpeeters@lashout.net>
To: "linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: sata_sil command 0x25 timeout, stat 0x50 host_stat 0x64
An update. I read that 2.6.7 might work better for the sata_sil driver, so
i tried running this version. But 2.6.7 doesn't solve my problem:
sata_sil version 0.54
PCI: Found IRQ 9 for device 0000:00:0e.0
ata1: SATA max UDMA/100 cmd 0xD086AE80 ctl 0xD086AE8A bmdma 0xD086AE00 irq
9
ata2: SATA max UDMA/100 cmd 0xD086AEC0 ctl 0xD086AECA bmdma 0xD086AE08 irq
9
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
88:207f
ata1: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
irq 9: nobody cared!
[<c01057fa>] __report_bad_irq+0x2a/0x90
[<c01058f0>] note_interrupt+0x70/0xb0
[<c0105b00>] do_IRQ+0xe0/0xf0
[<c0103fac>] common_interrupt+0x18/0x20
[<c01161ae>] __do_softirq+0x2e/0x80
[<c0116227>] do_softirq+0x27/0x30
[<c0105ae5>] do_IRQ+0xc5/0xf0
[<c0103fac>] common_interrupt+0x18/0x20
[<c01c007b>] idr_pre_get+0x2b/0x50
[<c010d5c4>] delay_tsc+0x14/0x20
[<c01c3ff2>] __delay+0x12/0x20
[<c023252d>] ata_busy_sleep+0x1d/0x130
[<c0232e44>] ata_dev_set_xfermode+0x94/0x190
[<c0232f94>] ata_dev_set_udma+0x54/0xc0
[<c02324d1>] ata_set_mode+0x51/0x90
[<c02322d8>] ata_port_reset+0x88/0xc0
[<c0234500>] ata_probe_task+0x0/0x60
[<c02342a8>] ata_thread_iter+0x48/0xc0
[<c0234513>] ata_probe_task+0x13/0x60
[<c011ffdd>] worker_thread+0x1ad/0x250
[<c010ff10>] default_wake_function+0x0/0x20
[<c010ff10>] default_wake_function+0x0/0x20
[<c011fe30>] worker_thread+0x0/0x250
[<c01231aa>] kthread+0xaa/0xb0
[<c0123100>] kthread+0x0/0xb0
[<c010223d>] kernel_thread_helper+0x5/0x18
handlers:
[<c0234120>] (ata_interrupt+0x0/0x140)
Disabling IRQ #9
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
88:207f
ata2: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_sil
Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sda: drive cache: write back
sda:<3>ata1: DMA timeout, stat 0x64
unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdb: drive cache: write back
sdb:<3>ata2: DMA timeout, stat 0x64
unknown partition table
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
PCI: Found IRQ 10 for device 0000:00:10.0
ata3: SATA max UDMA/100 cmd 0xD0877C80 ctl 0xD0877C8A bmdma 0xD0877C00 irq
10
ata4: SATA max UDMA/100 cmd 0xD0877CC0 ctl 0xD0877CCA bmdma 0xD0877C08 irq
10
irq 10: nobody cared!
[<c01057fa>] __report_bad_irq+0x2a/0x90
[<c01058f0>] note_interrupt+0x70/0xb0
[<c0105b00>] do_IRQ+0xe0/0xf0
[<c0103fac>] common_interrupt+0x18/0x20
[<c01161ae>] __do_softirq+0x2e/0x80
[<c0116227>] do_softirq+0x27/0x30
[<c0105ae5>] do_IRQ+0xc5/0xf0
[<c0103fac>] common_interrupt+0x18/0x20
[<c01c007b>] idr_pre_get+0x2b/0x50
[<c010d5c4>] delay_tsc+0x14/0x20
[<c01c3ff2>] __delay+0x12/0x20
[<c023252d>] ata_busy_sleep+0x1d/0x130
[<c0231d3b>] ata_dev_identify+0xdb/0x5f0
[<c01c3ff2>] __delay+0x12/0x20
[<c02329b9>] ata_bus_reset+0x129/0x210
[<c02323e5>] sata_phy_reset+0xc5/0x140
[<c0232284>] ata_port_reset+0x34/0xc0
[<c0234500>] ata_probe_task+0x0/0x60
[<c02342a8>] ata_thread_iter+0x48/0xc0
[<c0234513>] ata_probe_task+0x13/0x60
[<c011ffdd>] worker_thread+0x1ad/0x250
[<c010ff10>] default_wake_function+0x0/0x20
[<c010ff10>] default_wake_function+0x0/0x20
[<c011fe30>] worker_thread+0x0/0x250
[<c01231aa>] kthread+0xaa/0xb0
[<c0123100>] kthread+0x0/0xb0
[<c010223d>] kernel_thread_helper+0x5/0x18
handlers:
[<c0234120>] (ata_interrupt+0x0/0x140)
Disabling IRQ #10
ata3: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
88:207f
ata3: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata3: dev 0 configured for UDMA/100
scsi2 : sata_sil
ata4: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
88:207f
ata4: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata4: dev 0 configured for UDMA/100
scsi3 : sata_sil
Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdc: drive cache: write back
sdc:<3>ata3: DMA timeout, stat 0x64
unknown partition table
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 0
Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdd: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdd: drive cache: write back
sdd:<3>ata4: DMA timeout, stat 0x64
unknown partition table
Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 0, type 0
I will try further to get it working :)
Greetings,
Johannes Peeters
On Sat, 9 Oct 2004, Johannes Peeters wrote:
> Hello,
>
> I tried a lot of settings to get my sata drives working. I'm using 2 Sata
> Sil3112 controllers (SATALink, Sil3112ACT144, Q22389.110A & Q22389.119A)
> with both the latest bios (4.2.50) and 4 Maxtor Diamond Max Plug 9
> (6Y200M0) harddisk.
>
> In kernel 2.6.8.1, the siimage driver is working fine. The sata_sil driver
> howevers gives me weird timeouts:
>
> libata version 1.02 loaded.
> sata_sil version 0.54
> PCI: Found IRQ 9 for device 0000:00:0e.0
> ata1: SATA max UDMA/100 cmd 0xD0854E80 ctl 0xD0854E8A bmdma 0xD0854E00 irq
> 9
> ata2: SATA max UDMA/100 cmd 0xD0854EC0 ctl 0xD0854ECA bmdma 0xD0854E08 irq
> 9
> irq 9: nobody cared!
> [<c01062ba>] __report_bad_irq+0x2a/0x90
> [<c01063b0>] note_interrupt+0x70/0xb0
> [<c01065f0>] do_IRQ+0xe0/0xf0
> [<c010497c>] common_interrupt+0x18/0x20
> [<c0118fbe>] __do_softirq+0x2e/0x80
> [<c0119037>] do_softirq+0x27/0x30
> [<c01065d5>] do_IRQ+0xc5/0xf0
> [<c010497c>] common_interrupt+0x18/0x20
> [<c021007b>] des_small_fips_encrypt+0x41b/0x9f0
> [<c010e496>] delay_tsc+0x16/0x20
> [<c0216822>] __delay+0x12/0x20
> [<d08623bd>] ata_busy_sleep+0x1d/0x130 [libata]
> [<d0861bbb>] ata_dev_identify+0xdb/0x610 [libata]
> [<c0216822>] __delay+0x12/0x20
> [<d0862852>] ata_bus_reset+0x132/0x220 [libata]
> [<d0862275>] sata_phy_reset+0xc5/0x140 [libata]
> [<d0862124>] ata_bus_probe+0x34/0xb0 [libata]
> [<d086462c>] ata_device_add+0x1ac/0x250 [libata]
> [<d0863ec0>] ata_interrupt+0x0/0x1b0 [libata]
> [<d0858511>] sil_init_one+0x281/0x320 [sata_sil]
> [<c0221702>] pci_device_probe_static+0x52/0x70
> [<c022175c>] __pci_device_probe+0x3c/0x50
> [<c022179c>] pci_device_probe+0x2c/0x50
> [<c0261caf>] bus_match+0x3f/0x70
> [<c0261ddc>] driver_attach+0x5c/0xa0
> [<c0262301>] bus_add_driver+0x91/0xb0
> [<c02628af>] driver_register+0x2f/0x40
> [<c0221a1c>] pci_register_driver+0x5c/0x90
> [<d085b00f>] sil_init+0xf/0x1b [sata_sil]
> [<c012a5c8>] sys_init_module+0x108/0x1d0
> [<c010400f>] syscall_call+0x7/0xb
> handlers:
> [<d0863ec0>] (ata_interrupt+0x0/0x1b0 [libata])
> Disabling IRQ #9
> ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
> 88:207f
> ata1: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata1: dev 0 configured for UDMA/100
> scsi0 : sata_sil
> ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
> 88:207f
> ata2: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata2: dev 0 configured for UDMA/100
> scsi1 : sata_sil
> Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sda: drive cache: write back
> sda:<3>ata1: command 0x25 timeout, stat 0x50 host_stat 0x64
> unknown partition table
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdb: drive cache: write back
> sdb:<3>ata2: command 0x25 timeout, stat 0x50 host_stat 0x64
> unknown partition table
> Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
> Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
> PCI: Found IRQ 10 for device 0000:00:10.0
> ata3: SATA max UDMA/100 cmd 0xD0856C80 ctl 0xD0856C8A bmdma 0xD0856C00 irq
> 10
> ata4: SATA max UDMA/100 cmd 0xD0856CC0 ctl 0xD0856CCA bmdma 0xD0856C08 irq
> 10
> irq 10: nobody cared!
> [<c01062ba>] __report_bad_irq+0x2a/0x90
> [<c01063b0>] note_interrupt+0x70/0xb0
> [<c01065f0>] do_IRQ+0xe0/0xf0
> [<c010497c>] common_interrupt+0x18/0x20
> [<c0118fbe>] __do_softirq+0x2e/0x80
> [<c0119037>] do_softirq+0x27/0x30
> [<c01065d5>] do_IRQ+0xc5/0xf0
> [<c010497c>] common_interrupt+0x18/0x20
> [<c021007b>] des_small_fips_encrypt+0x41b/0x9f0
> [<c010e494>] delay_tsc+0x14/0x20
> [<c0216822>] __delay+0x12/0x20
> [<d08623bd>] ata_busy_sleep+0x1d/0x130 [libata]
> [<d0861bbb>] ata_dev_identify+0xdb/0x610 [libata]
> [<c0216822>] __delay+0x12/0x20
> [<d0862852>] ata_bus_reset+0x132/0x220 [libata]
> [<d0862275>] sata_phy_reset+0xc5/0x140 [libata]
> [<d0862124>] ata_bus_probe+0x34/0xb0 [libata]
> [<d086462c>] ata_device_add+0x1ac/0x250 [libata]
> [<d0863ec0>] ata_interrupt+0x0/0x1b0 [libata]
> [<d0858511>] sil_init_one+0x281/0x320 [sata_sil]
> [<c0221702>] pci_device_probe_static+0x52/0x70
> [<c022175c>] __pci_device_probe+0x3c/0x50
> [<c022179c>] pci_device_probe+0x2c/0x50
> [<c0261caf>] bus_match+0x3f/0x70
> [<c0261ddc>] driver_attach+0x5c/0xa0
> [<c0262301>] bus_add_driver+0x91/0xb0
> [<c02628af>] driver_register+0x2f/0x40
> [<c0221a1c>] pci_register_driver+0x5c/0x90
> [<d085b00f>] sil_init+0xf/0x1b [sata_sil]
> [<c012a5c8>] sys_init_module+0x108/0x1d0
> [<c010400f>] syscall_call+0x7/0xb
> handlers:
> [<d0863ec0>] (ata_interrupt+0x0/0x1b0 [libata])
> Disabling IRQ #10
> ata3: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
> 88:207f
> ata3: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata3: dev 0 configured for UDMA/100
> scsi2 : sata_sil
> ata4: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
> 88:207f
> ata4: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata4: dev 0 configured for UDMA/100
> scsi3 : sata_sil
> Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sdc: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdc: drive cache: write back
> sdc:<3>ata3: command 0x25 timeout, stat 0x50 host_stat 0x64
> unknown partition table
> Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
> Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 0
> Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sdd: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdd: drive cache: write back
> sdd:<3>ata4: command 0x25 timeout, stat 0x50 host_stat 0x64
> unknown partition table
> Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
> Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 0, type 0
>
> Reading/writing to this disc doesn't work, this gives me an endless
> process.
>
>
>
> I also tried with 2.6.9-rc3-bk7, but that gives me an other problem:
>
>
> libata version 1.02 loaded.
> sata_sil version 0.54
> PCI: Found IRQ 9 for device 0000:00:0e.0
> ata1: SATA max UDMA/100 cmd 0xD0854E80 ctl 0xD0854E8A bmdma 0xD0854E00 irq
> 9
> ata2: SATA max UDMA/100 cmd 0xD0854EC0 ctl 0xD0854ECA bmdma 0xD0854E08 irq
> 9
> ata1: no device found (phy stat 00000000)
> scsi0 : sata_sil
> irq 9: nobody cared!
> [<c0105e9a>] __report_bad_irq+0x2a/0x90
> [<c0105f90>] note_interrupt+0x70/0xb0
> [<c01061a0>] do_IRQ+0xe0/0xf0
> [<c010413c>] common_interrupt+0x18/0x20
> [<c011801e>] __do_softirq+0x2e/0x90
> [<c01180a7>] do_softirq+0x27/0x30
> [<c0106185>] do_IRQ+0xc5/0xf0
> [<c010413c>] common_interrupt+0x18/0x20
> [<c01020c3>] default_idle+0x23/0x40
> [<c0102154>] cpu_idle+0x34/0x40
> [<c044272b>] start_kernel+0x13b/0x160
> [<c0442370>] unknown_bootoption+0x0/0x160
> handlers:
> [<d0865160>] (ata_interrupt+0x0/0x1c0 [libata])
> Disabling IRQ #9
> ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
> 88:207f
> ata2: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
>
> After this, loading the module stops. I've wait a couple of hours, but
> this was the last message.
> Trying to enable/disable APIC & IOAPIC didn't solve the problem.
>
> Any suggestions?
>
> Thanks,
> Johannes Peeters
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: sata_sil command 0x25 timeout, stat 0x50 host_stat 0x64 (fwd)
2004-10-11 15:07 sata_sil command 0x25 timeout, stat 0x50 host_stat 0x64 (fwd) Johannes Peeters
@ 2004-10-11 15:19 ` Jeff Garzik
2004-10-11 16:29 ` Johannes Peeters
2004-10-11 21:09 ` Johannes Peeters
0 siblings, 2 replies; 4+ messages in thread
From: Jeff Garzik @ 2004-10-11 15:19 UTC (permalink / raw)
To: Johannes Peeters; +Cc: linux-ide
On Mon, Oct 11, 2004 at 03:07:37PM +0000, Johannes Peeters wrote:
> Hello,
>
> I accidentaly send this to the linux-kernel mailinlist, but i had to send
> it to the linux-ide list.
>
> I also tried noapic acpi=off pci=biosirq, but no success. Do you have any
> idea what to do next?
You try each of those command line options individually, not together.
And did you update your card and system BIOS?
Jeff
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: sata_sil command 0x25 timeout, stat 0x50 host_stat 0x64 (fwd)
2004-10-11 15:19 ` Jeff Garzik
@ 2004-10-11 16:29 ` Johannes Peeters
2004-10-11 21:09 ` Johannes Peeters
1 sibling, 0 replies; 4+ messages in thread
From: Johannes Peeters @ 2004-10-11 16:29 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide
On Mon, 11 Oct 2004, Jeff Garzik wrote:
> On Mon, Oct 11, 2004 at 03:07:37PM +0000, Johannes Peeters wrote:
> > Hello,
> >
> > I accidentaly send this to the linux-kernel mailinlist, but i had to send
> > it to the linux-ide list.
> >
> > I also tried noapic acpi=off pci=biosirq, but no success. Do you have any
> > idea what to do next?
>
> You try each of those command line options individually, not together.
>
> And did you update your card and system BIOS?
>
> Jeff
>
I tried them individually, but none of them worked.
I was a bit afraid of a bios upgrade (it's an old compaq), but did it. The
cards already have the latsts firmware.
With the new bios, the problem still exists...
With the siimage driver it works fine, so i think it's not related to the
controllers/disks.
Do you need anymore information?
Thanks,
Johannes Peeters
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: sata_sil command 0x25 timeout, stat 0x50 host_stat 0x64 (fwd)
2004-10-11 15:19 ` Jeff Garzik
2004-10-11 16:29 ` Johannes Peeters
@ 2004-10-11 21:09 ` Johannes Peeters
1 sibling, 0 replies; 4+ messages in thread
From: Johannes Peeters @ 2004-10-11 21:09 UTC (permalink / raw)
To: linux-ide; +Cc: Jeff Garzik
On Mon, 11 Oct 2004, Jeff Garzik wrote:
> On Mon, Oct 11, 2004 at 03:07:37PM +0000, Johannes Peeters wrote:
> > Hello,
> >
> > I accidentaly send this to the linux-kernel mailinlist, but i had to send
> > it to the linux-ide list.
> >
> > I also tried noapic acpi=off pci=biosirq, but no success. Do you have any
> > idea what to do next?
>
> You try each of those command line options individually, not together.
>
> And did you update your card and system BIOS?
>
> Jeff
>
I tried them individually, but none of them worked.
I was a bit afraid of a bios upgrade (it's an old compaq), but did it. The
cards already have the latsts firmware.
With the new bios, the problem still exists...
With the siimage driver it works fine, so i think it's not related to the
controllers/disks.
Do you need anymore information?
Thanks,
Johannes
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2004-10-11 21:09 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2004-10-11 15:07 sata_sil command 0x25 timeout, stat 0x50 host_stat 0x64 (fwd) Johannes Peeters
2004-10-11 15:19 ` Jeff Garzik
2004-10-11 16:29 ` Johannes Peeters
2004-10-11 21:09 ` Johannes Peeters
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.