* [PATCH 2/7] gpu: drm: panel: Add Innolux TD4328 panel driver
[not found] <20220606230522.107428-1-teguh@sobir.in>
@ 2022-06-06 23:05 ` Teguh Sobirin
2022-06-06 23:05 ` [PATCH 3/7] arm64: dts: qcom: add support for AYN Odin Base and Pro Teguh Sobirin
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Teguh Sobirin @ 2022-06-06 23:05 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
linux-arm-msm, devicetree, phone-devel
Signed-off-by: Teguh Sobirin <teguh@sobir.in>
---
drivers/gpu/drm/panel/Kconfig | 9 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-innolux-td4328.c | 339 +++++++++++++++++++
3 files changed, 349 insertions(+)
create mode 100644 drivers/gpu/drm/panel/panel-innolux-td4328.c
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index a89c03379db5..50ecd01872b9 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -202,6 +202,15 @@ config DRM_PANEL_INNOLUX_P079ZCA
24 bit RGB per pixel. It provides a MIPI DSI interface to
the host and has a built-in LED backlight.
+config DRM_PANEL_INNOLUX_TD4328
+ tristate "Innolux TD4328 DSI panel"
+ depends on OF
+ depends on DRM_MIPI_DSI
+ depends on BACKLIGHT_CLASS_DEVICE
+ help
+ Say Y here if you want to enable support for the panels built
+ around the Innolux TD4328 display controller.
+
config DRM_PANEL_JDI_LT070ME05000
tristate "JDI LT070ME05000 WUXGA DSI panel"
depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index ddf488b96cb3..cc3389a13a2a 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o
obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
obj-$(CONFIG_DRM_PANEL_INNOLUX_EJ030NA) += panel-innolux-ej030na.o
obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
+obj-$(CONFIG_DRM_PANEL_INNOLUX_TD4328) += panel-innolux-td4328.o
obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
obj-$(CONFIG_DRM_PANEL_JDI_R63452) += panel-jdi-fhd-r63452.o
obj-$(CONFIG_DRM_PANEL_KHADAS_TS050) += panel-khadas-ts050.o
diff --git a/drivers/gpu/drm/panel/panel-innolux-td4328.c b/drivers/gpu/drm/panel/panel-innolux-td4328.c
new file mode 100644
index 000000000000..7c17f8c06512
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-innolux-td4328.c
@@ -0,0 +1,339 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Teguh Sobirin
+ * Author: Teguh Sobirin <teguh@sobir.in>
+ *
+ * This driver is for the DSI interface to Innolux panel
+ * Using the TD4328 display driver IC from Synaptics.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regulator/consumer.h>
+
+#include <video/display_timing.h>
+#include <video/mipi_display.h>
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+struct td4328 {
+ struct device *dev;
+ struct drm_panel panel;
+ struct regulator *supply;
+ struct gpio_desc *reset_gpio;
+ enum drm_panel_orientation orientation;
+ bool prepared;
+};
+
+static inline struct td4328 *panel_to_td4328(struct drm_panel *panel)
+{
+ return container_of(panel, struct td4328, panel);
+}
+
+static int td4328_init_sequence(struct td4328 *ctx)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ struct device *dev = ctx->dev;
+ int ret;
+
+ ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+ if (ret < 0) {
+ dev_err(dev, "Failed to exit sleep mode: %d\n", ret);
+ return ret;
+ }
+ msleep(70);
+
+ ret = mipi_dsi_dcs_set_column_address(dsi, 0, 1080 - 1);
+ if (ret < 0) {
+ dev_err(dev, "Failed to set sleep column address: %d\n", ret);
+ return ret;
+ }
+
+ ret = mipi_dsi_dcs_set_page_address(dsi, 0, 1920 - 1);
+ if (ret < 0) {
+ dev_err(dev, "Failed to set sleep page address: %d\n", ret);
+ return ret;
+ }
+
+ ret = mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
+
+ if (ret < 0) {
+ dev_err(dev, "Failed to set tear on: %d\n", ret);
+ return ret;
+ }
+
+ ret = mipi_dsi_dcs_set_display_on(dsi);
+ if (ret < 0) {
+ dev_err(dev, "Failed to set display on: %d\n", ret);
+ return ret;
+ }
+
+ dev_dbg(dev, "Panel init sequence done\n");
+ return 0;
+}
+
+static int td4328_unprepare(struct drm_panel *panel)
+{
+ struct td4328 *ctx = panel_to_td4328(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ int ret;
+
+ if (!ctx->prepared)
+ return 0;
+
+ ret = mipi_dsi_dcs_set_display_off(dsi);
+ if (ret < 0)
+ dev_err(ctx->dev, "failed to set display off: %d\n", ret);
+
+ ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "failed to enter sleep mode: %d\n", ret);
+ return ret;
+ }
+
+ regulator_disable(ctx->supply);
+
+ ctx->prepared = false;
+
+ return 0;
+}
+
+static int td4328_prepare(struct drm_panel *panel)
+{
+ struct td4328 *ctx = panel_to_td4328(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ int ret;
+
+ if (ctx->prepared)
+ return 0;
+
+ dev_dbg(ctx->dev, "Resetting the panel\n");
+ ret = regulator_enable(ctx->supply);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to enable supply: %d\n", ret);
+ return ret;
+ }
+
+ msleep(20);
+
+ gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+ usleep_range(10, 20);
+ gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+
+ msleep(20);
+
+ ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to exit sleep mode: %d\n", ret);
+ goto disable_supply;
+ }
+
+ msleep(250);
+
+ ret = td4328_init_sequence(ctx);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Panel init sequence failed: %d\n", ret);
+ goto disable_supply;
+ }
+
+ ret = mipi_dsi_dcs_set_display_on(dsi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to set display on: %d\n", ret);
+ goto disable_supply;
+ }
+
+ msleep(50);
+
+ ctx->prepared = true;
+
+ return 0;
+
+disable_supply:
+ regulator_disable(ctx->supply);
+ return ret;
+}
+
+static const struct drm_display_mode default_mode = {
+ .clock = (1080 + 60 + 10 + 60) * (1920 + 20 + 8 + 20) * 60 / 1000,
+ .hdisplay = 1080,
+ .hsync_start = 1080 + 60,
+ .hsync_end = 1080 + 60 + 10,
+ .htotal = 1080 + 60 + 10 + 60,
+ .vdisplay = 1920,
+ .vsync_start = 1920 + 20,
+ .vsync_end = 1920 + 20 + 8,
+ .vtotal = 1920 + 20 + 8 + 20,
+ .width_mm = 75,
+ .height_mm = 132,
+};
+
+static int td4328_get_modes(struct drm_panel *panel,
+ struct drm_connector *connector)
+{
+ struct td4328 *ctx = panel_to_td4328(panel);
+ struct drm_display_mode *mode;
+
+ mode = drm_mode_duplicate(connector->dev, &default_mode);
+ if (!mode) {
+ dev_err(ctx->dev, "Failed to add mode %ux%u@%u\n",
+ default_mode.hdisplay, default_mode.vdisplay,
+ drm_mode_vrefresh(&default_mode));
+ return -ENOMEM;
+ }
+
+ drm_mode_set_name(mode);
+
+ mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+ connector->display_info.width_mm = mode->width_mm;
+ connector->display_info.height_mm = mode->height_mm;
+ drm_mode_probed_add(connector, mode);
+ drm_connector_set_panel_orientation(connector, ctx->orientation);
+
+ return 1;
+}
+
+static const struct drm_panel_funcs td4328_funcs = {
+ .unprepare = td4328_unprepare,
+ .prepare = td4328_prepare,
+ .get_modes = td4328_get_modes,
+};
+
+static int td4328_probe(struct mipi_dsi_device *dsi)
+{
+ struct device *dev = &dsi->dev;
+ struct td4328 *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ ctx->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(ctx->reset_gpio)) {
+ dev_err(dev, "cannot get reset gpio\n");
+ return PTR_ERR(ctx->reset_gpio);
+ }
+
+ ctx->supply = devm_regulator_get(dev, "vdd");
+ if (IS_ERR(ctx->supply)) {
+ ret = PTR_ERR(ctx->supply);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "Failed to request vdd regulator: %d\n", ret);
+ return ret;
+ }
+
+ ctx->supply = devm_regulator_get(dev, "vddio");
+ if (IS_ERR(ctx->supply)) {
+ ret = PTR_ERR(ctx->supply);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "Failed to request vddio regulator: %d\n", ret);
+ return ret;
+ }
+
+ ctx->supply = devm_regulator_get(dev, "vddpos");
+ if (IS_ERR(ctx->supply)) {
+ ret = PTR_ERR(ctx->supply);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "Failed to request vddpos regulator: %d\n", ret);
+ return ret;
+ }
+
+ ctx->supply = devm_regulator_get(dev, "vddneg");
+ if (IS_ERR(ctx->supply)) {
+ ret = PTR_ERR(ctx->supply);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "Failed to request vddneg regulator: %d\n", ret);
+ return ret;
+ }
+
+ ret = of_drm_get_panel_orientation(dev->of_node, &ctx->orientation);
+ if (ret < 0) {
+ dev_err(dev, "Failed to get orientation %d\n", ret);
+ return ret;
+ }
+
+ mipi_dsi_set_drvdata(dsi, ctx);
+
+ ctx->dev = dev;
+
+ dsi->lanes = 4;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_LPM
+ | MIPI_DSI_MODE_VIDEO_HSE
+ | MIPI_DSI_CLOCK_NON_CONTINUOUS
+ | MIPI_DSI_MODE_VIDEO_BURST
+ | MIPI_DSI_MODE_NO_EOT_PACKET;
+
+ drm_panel_init(&ctx->panel, &dsi->dev, &td4328_funcs,
+ DRM_MODE_CONNECTOR_DSI);
+
+ ret = drm_panel_of_backlight(&ctx->panel);
+ if (ret)
+ return ret;
+
+ drm_panel_add(&ctx->panel);
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0) {
+ dev_err(dev, "mipi_dsi_attach failed: %d\n", ret);
+ drm_panel_remove(&ctx->panel);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void td4328_shutdown(struct mipi_dsi_device *dsi)
+{
+ struct td4328 *ctx = mipi_dsi_get_drvdata(dsi);
+ int ret;
+
+ ret = drm_panel_unprepare(&ctx->panel);
+ if (ret < 0)
+ dev_err(&dsi->dev, "Failed to unprepare panel: %d\n", ret);
+
+ ret = drm_panel_disable(&ctx->panel);
+ if (ret < 0)
+ dev_err(&dsi->dev, "Failed to disable panel: %d\n", ret);
+}
+
+static int td4328_remove(struct mipi_dsi_device *dsi)
+{
+ struct td4328 *ctx = mipi_dsi_get_drvdata(dsi);
+ int ret;
+
+ td4328_shutdown(dsi);
+
+ ret = mipi_dsi_detach(dsi);
+ if (ret < 0)
+ dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret);
+
+ drm_panel_remove(&ctx->panel);
+
+ return 0;
+}
+
+static const struct of_device_id td4328_of_match[] = {
+ { .compatible = "innolux,td4328" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, td4328_of_match);
+
+static struct mipi_dsi_driver td4328_driver = {
+ .driver = {
+ .name = "panel-innolux-td4328",
+ .of_match_table = td4328_of_match,
+ },
+ .probe = td4328_probe,
+ .remove = td4328_remove,
+ .shutdown = td4328_shutdown,
+};
+module_mipi_dsi_driver(td4328_driver);
+
+MODULE_AUTHOR("Teguh Sobirin <teguh@sobir.in>");
+MODULE_DESCRIPTION("DRM driver for TD4328 cmd mode DSI Innolux panel");
+MODULE_LICENSE("GPL v2");
--
2.30.2
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 3/7] arm64: dts: qcom: add support for AYN Odin Base and Pro
[not found] <20220606230522.107428-1-teguh@sobir.in>
2022-06-06 23:05 ` [PATCH 2/7] gpu: drm: panel: Add Innolux TD4328 panel driver Teguh Sobirin
@ 2022-06-06 23:05 ` Teguh Sobirin
2022-06-06 23:05 ` [PATCH 4/7] arm64: configs: add Odin support in sdm845.config Teguh Sobirin
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Teguh Sobirin @ 2022-06-06 23:05 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
linux-arm-msm, devicetree, phone-devel
Signed-off-by: Teguh Sobirin <teguh@sobir.in>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts | 743 +++++++++++++++++++
2 files changed, 744 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 84381452d0b6..7dedfb797b28 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -92,6 +92,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-pioneer.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-voyager.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm636-sony-xperia-ganges-mermaid.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm660-xiaomi-lavender.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-ayn-odin.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts b/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
new file mode 100644
index 000000000000..cca43d55baa5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
@@ -0,0 +1,743 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022, Teguh Sobirin.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/ {
+ model = "Odin - AYN Technologies Co., Ltd.";
+ compatible = "qcom,sdm845-mtp", "qcom,sdm845", "qcom,mtp";
+ qcom,msm-id = <321 0x20001>;
+ qcom,board-id = <8 0>;
+ chassis-type = "tablet";
+
+ aliases {
+ serial0 = &uart9;
+ hsuart0 = &uart6;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&volume_up_gpio>;
+
+ vol-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ battery: battery {
+ compatible = "simple-battery";
+
+ charge-full-design-microamp-hours = <3850000>;
+ voltage-min-design-microvolt = <3600000>;
+ voltage-max-design-microvolt = <4400000>;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ vreg_s4a_1p8: pm8998-smps4 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&vph_pwr>;
+ };
+};
+
+&adsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/odin/adsp.mbn";
+};
+
+&apps_rsc {
+ pm8998-rpmh-regulators {
+ compatible = "qcom,pm8998-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+ vdd-s11-supply = <&vph_pwr>;
+ vdd-s12-supply = <&vph_pwr>;
+ vdd-s13-supply = <&vph_pwr>;
+ vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+ vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+ vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+ vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+ vdd-l6-supply = <&vph_pwr>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+ vdd-l9-supply = <&vreg_bob>;
+ vdd-l10-l23-l25-supply = <&vreg_bob>;
+ vdd-l13-l19-l21-supply = <&vreg_bob>;
+ vdd-l16-l28-supply = <&vreg_bob>;
+ vdd-l18-l22-supply = <&vreg_bob>;
+ vdd-l20-l24-supply = <&vreg_bob>;
+ vdd-l26-supply = <&vreg_s3a_1p35>;
+ vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+ vreg_s3a_1p35: smps3 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_s5a_2p04: smps5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2040000>;
+ };
+
+ vreg_s7a_1p025: smps7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1028000>;
+ };
+
+ vdda_mipi_dsi0_pll:
+ vdda_mipi_dsi1_pll:
+ vdda_qlink_lv:
+ vdda_ufs1_core:
+ vdda_usb1_ss_core:
+ vdda_qusb_hs0_1p8:
+ vdda_qusb_hs0_3p1:
+ vdda_mipi_dsi0_1p2:
+
+ vdda_ufs1_1p2:
+
+ vreg_l1a_0p875: ldo1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a_0p8: ldo5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13a_2p95: ldo13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14a_1p8: ldo14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_l17a_1p3: ldo17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l20a_2p95: ldo20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l21a_2p95: ldo21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l24a_3p075: ldo24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l25a_3p3: ldo25 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l26a_1p2: ldo26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
+ };
+
+ vreg_l28a_3p0: ldo28 {
+ regulator-min-microvolt = <2856000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pmi8998-rpmh-regulators {
+ compatible = "qcom,pmi8998-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ regulator-allow-bypass;
+ };
+ };
+
+ pm8005-rpmh-regulators {
+ compatible = "qcom,pm8005-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+
+ vreg_s3c_0p6: smps3 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <600000>;
+ };
+ };
+};
+
+&cdsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/odin/cdsp.mbn";
+};
+
+&dsi0 {
+ status = "okay";
+ vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+ panel@0 {
+ compatible = "innolux,td4328";
+ status = "okay";
+ reg = <0>;
+ vddio-supply = <&vreg_l14a_1p8>;
+ vddpos-supply = <&lab>;
+ vddneg-supply = <&ibb>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ backlight = <&pmi8998_wled>;
+ reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+ rotation = <90>;
+
+ port {
+ panel_in_0: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+};
+
+&dsi0_out {
+ remote-endpoint = <&panel_in_0>;
+ data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+ status = "okay";
+ vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
+&gcc {
+ protected-clocks = <GCC_QSPI_CORE_CLK>,
+ <GCC_QSPI_CORE_CLK_SRC>,
+ <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <GCC_LPASS_Q6_AXI_CLK>,
+ <GCC_LPASS_SWAY_CLK>;
+};
+
+&gmu {
+ status = "okay";
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sdm845/odin/a630_zap.mbn";
+ };
+};
+
+&pmi8998_haptics {
+ status = "okay";
+ qcom,wave-play-rate-us = <4255>;
+};
+
+&i2c5 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ synaptics-rmi4-i2c@70 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x70>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_active &ts_reset_active>;
+
+ vdd-supply = <&vreg_l28a_3p0>;
+ vio-supply = <&vreg_l14a_1p8>;
+
+ syna,reset-delay-ms = <200>;
+ syna,startup-delay-ms = <200>;
+
+ rmi4-f01@1 {
+ reg = <0x01>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4_f12: rmi4-f12@12 {
+ reg = <0x12>;
+ touchscreen-inverted-x;
+ touchscreen-x-mm = <75>;
+ touchscreen-y-mm = <132>;
+ syna,sensor-type = <1>;
+ syna,rezero-wait-ms = <200>;
+ };
+ };
+};
+
+&ibb {
+ regulator-min-microvolt = <4600000>;
+ regulator-max-microvolt = <6000000>;
+ regulator-over-current-protection;
+ regulator-pull-down;
+ regulator-soft-start;
+ qcom,discharge-resistor-kohms = <300>;
+};
+
+&lab {
+ regulator-min-microvolt = <4600000>;
+ regulator-max-microvolt = <6000000>;
+ regulator-over-current-protection;
+ regulator-pull-down;
+ regulator-soft-start;
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mss_pil {
+ status = "okay";
+ firmware-name = "qcom/sdm845/odin/mba.mbn", "qcom/sdm845/odin/modem.mbn";
+};
+
+&pm8998_gpio {
+ volume_up_gpio: vol-up-active {
+ pins = "gpio6";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+};
+
+&pm8998_pon {
+ volume_down_resin: resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+};
+
+&pmi8998_fg {
+ status = "okay";
+ monitored-battery = <&battery>;
+};
+
+&pmi8998_rradc {
+ status = "okay";
+};
+
+&pmi8998_smb2 {
+ status = "okay";
+ monitored-battery = <&battery>;
+};
+
+&pmi8998_wled {
+ status = "okay";
+ qcom,enabled-strings = <0 1>;
+ qcom,num-strings = <2>;
+};
+
+/* QUAT I2S Uses 1 I2S SD Line for audio on HDMI Bridge */
+&q6afedai {
+ qi2s@22 {
+ reg = <22>;
+ qcom,sd-lines = <0>;
+ };
+};
+
+&q6asmdai {
+ dai@0 {
+ reg = <0>;
+ };
+
+ dai@1 {
+ reg = <1>;
+ };
+
+ dai@2 {
+ reg = <2>;
+ };
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&qup_uart6_default {
+ pinmux {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "qup6";
+ };
+
+ cts {
+ pins = "gpio45";
+ bias-disable;
+ };
+
+ rts-tx {
+ pins = "gpio46", "gpio47";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio48";
+ bias-pull-up;
+ };
+};
+
+&qup_uart9_default {
+ pinconf-tx {
+ pins = "gpio4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ pins = "gpio5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
+
+ vmmc-supply = <&vreg_l21a_2p95>;
+ vqmmc-supply = <&vreg_l13a_2p95>;
+
+ bus-width = <4>;
+ cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
+};
+
+&slpi_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/odin/slpi.mbn";
+};
+
+&sound {
+ compatible = "qcom,db845c-sndcard";
+ pinctrl-0 = <&quat_mi2s_active
+ &quat_mi2s_sd0_active>;
+ pinctrl-names = "default";
+ model = "Odin";
+ audio-routing =
+ "RX_BIAS", "MCLK",
+ "AMIC1", "MIC BIAS1",
+ "AMIC2", "MIC BIAS2",
+ "AMIC3", "MIC BIAS3";
+
+ mm1-dai-link {
+ link-name = "MultiMedia1";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+ };
+ };
+
+ mm2-dai-link {
+ link-name = "MultiMedia2";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+ };
+ };
+
+ mm3-dai-link {
+ link-name = "MultiMedia3";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+ };
+ };
+
+ slim-dai-link {
+ link-name = "SLIM Playback";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_0_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
+ };
+ };
+
+ slimcap-dai-link {
+ link-name = "SLIM Capture";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_0_TX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9340 1>;
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ sdc2_default_state: sdc2-default {
+ clk {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+ };
+
+ sdc2_card_det_n: sd-card-det-n {
+ pins = "gpio126";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ wcd_intr_default: wcd_intr_default {
+ pins = <54>;
+ function = "gpio";
+
+ input-enable;
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+
+ ts_int_active: ts-int-active {
+ pins = "gpio125";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-pull-up;
+ input-enable;
+ };
+
+ ts_reset_active: ts-reset-active {
+ pins = "gpio104";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+};
+
+&uart6 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l17a_1p3>;
+ vddch0-supply = <&vreg_l25a_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&uart9 {
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ status = "okay";
+
+ reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l20a_2p95>;
+ vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+
+ vdd-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+ qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+ qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l26a_1p2>;
+ vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&venus {
+ status = "okay";
+ firmware-name = "qcom/sdm845/odin/venus.mbn";
+};
+
+&wcd9340{
+ pinctrl-0 = <&wcd_intr_default>;
+ pinctrl-names = "default";
+ clock-names = "extclk";
+ clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+ reset-gpios = <&tlmm 64 0>;
+ vdd-buck-supply = <&vreg_s4a_1p8>;
+ vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+ vdd-tx-supply = <&vreg_s4a_1p8>;
+ vdd-rx-supply = <&vreg_s4a_1p8>;
+ vdd-io-supply = <&vreg_s4a_1p8>;
+
+ swm: swm@c85 {
+ left_spkr: wsa8810-left{
+ compatible = "sdw10217201000";
+ reg = <0 1>;
+ powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
+ #thermal-sensor-cells = <0>;
+ sound-name-prefix = "SpkrLeft";
+ #sound-dai-cells = <0>;
+ };
+
+ right_spkr: wsa8810-right{
+ compatible = "sdw10217201000";
+ powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
+ reg = <0 2>;
+ #thermal-sensor-cells = <0>;
+ sound-name-prefix = "SpkrRight";
+ #sound-dai-cells = <0>;
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+
+ vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+
+ qcom,snoc-host-cap-8bit-quirk;
+};
--
2.30.2
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 4/7] arm64: configs: add Odin support in sdm845.config
[not found] <20220606230522.107428-1-teguh@sobir.in>
2022-06-06 23:05 ` [PATCH 2/7] gpu: drm: panel: Add Innolux TD4328 panel driver Teguh Sobirin
2022-06-06 23:05 ` [PATCH 3/7] arm64: dts: qcom: add support for AYN Odin Base and Pro Teguh Sobirin
@ 2022-06-06 23:05 ` Teguh Sobirin
2022-06-06 23:05 ` [PATCH 5/7] arm64: dts: qcom: sdm845-ayn-odin: change compatible name Teguh Sobirin
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Teguh Sobirin @ 2022-06-06 23:05 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
linux-arm-msm, devicetree, phone-devel
Signed-off-by: Teguh Sobirin <teguh@sobir.in>
---
arch/arm64/configs/sdm845.config | 3 +++
1 file changed, 3 insertions(+)
diff --git a/arch/arm64/configs/sdm845.config b/arch/arm64/configs/sdm845.config
index 2801d2535667..eb0575ad5d4b 100644
--- a/arch/arm64/configs/sdm845.config
+++ b/arch/arm64/configs/sdm845.config
@@ -19,6 +19,9 @@ CONFIG_SND_SOC_TAS2559=m
# SHIFT6mq
CONFIG_DRM_PANEL_VISIONOX_RM69299=y
+# Odin
+CONFIG_DRM_PANEL_INNOLUX_TD4328=y
+
# SOC
CONFIG_NR_CPUS=8
CONFIG_SCSI_UFS_QCOM=y
--
2.30.2
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 5/7] arm64: dts: qcom: sdm845-ayn-odin: change compatible name
[not found] <20220606230522.107428-1-teguh@sobir.in>
` (2 preceding siblings ...)
2022-06-06 23:05 ` [PATCH 4/7] arm64: configs: add Odin support in sdm845.config Teguh Sobirin
@ 2022-06-06 23:05 ` Teguh Sobirin
2022-06-06 23:05 ` [PATCH 6/7] fixup! dt-bindings: display: panel: Add Innolux TD4328 panel bindings Teguh Sobirin
2022-06-06 23:05 ` [PATCH 7/7] fixup! arm64: dts: qcom: add support for AYN Odin Base and Pro Teguh Sobirin
5 siblings, 0 replies; 7+ messages in thread
From: Teguh Sobirin @ 2022-06-06 23:05 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
linux-arm-msm, devicetree, phone-devel
Signed-off-by: Teguh Sobirin <teguh@sobir.in>
---
arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts b/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
index cca43d55baa5..545debd7c275 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
@@ -5,7 +5,6 @@
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include <dt-bindings/sound/qcom,q6afe.h>
@@ -16,7 +15,7 @@
/ {
model = "Odin - AYN Technologies Co., Ltd.";
- compatible = "qcom,sdm845-mtp", "qcom,sdm845", "qcom,mtp";
+ compatible = "ayn,odin", "qcom,sdm845", "qcom,mtp";
qcom,msm-id = <321 0x20001>;
qcom,board-id = <8 0>;
chassis-type = "tablet";
--
2.30.2
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 6/7] fixup! dt-bindings: display: panel: Add Innolux TD4328 panel bindings
[not found] <20220606230522.107428-1-teguh@sobir.in>
` (3 preceding siblings ...)
2022-06-06 23:05 ` [PATCH 5/7] arm64: dts: qcom: sdm845-ayn-odin: change compatible name Teguh Sobirin
@ 2022-06-06 23:05 ` Teguh Sobirin
2022-06-06 23:05 ` [PATCH 7/7] fixup! arm64: dts: qcom: add support for AYN Odin Base and Pro Teguh Sobirin
5 siblings, 0 replies; 7+ messages in thread
From: Teguh Sobirin @ 2022-06-06 23:05 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
linux-arm-msm, devicetree, phone-devel
Signed-off-by: Teguh Sobirin <teguh@sobir.in>
---
.../devicetree/bindings/display/panel/innolux,td4328.yaml | 0
1 file changed, 0 insertions(+), 0 deletions(-)
mode change 100755 => 100644 Documentation/devicetree/bindings/display/panel/innolux,td4328.yaml
diff --git a/Documentation/devicetree/bindings/display/panel/innolux,td4328.yaml b/Documentation/devicetree/bindings/display/panel/innolux,td4328.yaml
old mode 100755
new mode 100644
--
2.30.2
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 7/7] fixup! arm64: dts: qcom: add support for AYN Odin Base and Pro
[not found] <20220606230522.107428-1-teguh@sobir.in>
` (4 preceding siblings ...)
2022-06-06 23:05 ` [PATCH 6/7] fixup! dt-bindings: display: panel: Add Innolux TD4328 panel bindings Teguh Sobirin
@ 2022-06-06 23:05 ` Teguh Sobirin
2022-07-01 3:16 ` Bjorn Andersson
5 siblings, 1 reply; 7+ messages in thread
From: Teguh Sobirin @ 2022-06-06 23:05 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
linux-arm-msm, devicetree, phone-devel
Signed-off-by: Teguh Sobirin <teguh@sobir.in>
---
arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts b/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
index 545debd7c275..8deeb375bc1a 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
@@ -133,7 +133,7 @@ vdda_usb1_ss_core:
vdda_qusb_hs0_1p8:
vdda_qusb_hs0_3p1:
vdda_mipi_dsi0_1p2:
-
+
vdda_ufs1_1p2:
vreg_l1a_0p875: ldo1 {
--
2.30.2
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH 7/7] fixup! arm64: dts: qcom: add support for AYN Odin Base and Pro
2022-06-06 23:05 ` [PATCH 7/7] fixup! arm64: dts: qcom: add support for AYN Odin Base and Pro Teguh Sobirin
@ 2022-07-01 3:16 ` Bjorn Andersson
0 siblings, 0 replies; 7+ messages in thread
From: Bjorn Andersson @ 2022-07-01 3:16 UTC (permalink / raw)
To: Teguh Sobirin
Cc: Andy Gross, Rob Herring, Krzysztof Kozlowski, linux-arm-msm,
devicetree, phone-devel
On Mon 06 Jun 18:05 CDT 2022, Teguh Sobirin wrote:
Please squash this with the commit you're trying to fix and repost with
a cover-letter.
Thanks,
Bjorn
> Signed-off-by: Teguh Sobirin <teguh@sobir.in>
> ---
> arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts b/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
> index 545debd7c275..8deeb375bc1a 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-ayn-odin.dts
> @@ -133,7 +133,7 @@ vdda_usb1_ss_core:
> vdda_qusb_hs0_1p8:
> vdda_qusb_hs0_3p1:
> vdda_mipi_dsi0_1p2:
> -
> +
> vdda_ufs1_1p2:
>
> vreg_l1a_0p875: ldo1 {
> --
> 2.30.2
>
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2022-07-01 3:16 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <20220606230522.107428-1-teguh@sobir.in>
2022-06-06 23:05 ` [PATCH 2/7] gpu: drm: panel: Add Innolux TD4328 panel driver Teguh Sobirin
2022-06-06 23:05 ` [PATCH 3/7] arm64: dts: qcom: add support for AYN Odin Base and Pro Teguh Sobirin
2022-06-06 23:05 ` [PATCH 4/7] arm64: configs: add Odin support in sdm845.config Teguh Sobirin
2022-06-06 23:05 ` [PATCH 5/7] arm64: dts: qcom: sdm845-ayn-odin: change compatible name Teguh Sobirin
2022-06-06 23:05 ` [PATCH 6/7] fixup! dt-bindings: display: panel: Add Innolux TD4328 panel bindings Teguh Sobirin
2022-06-06 23:05 ` [PATCH 7/7] fixup! arm64: dts: qcom: add support for AYN Odin Base and Pro Teguh Sobirin
2022-07-01 3:16 ` Bjorn Andersson
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.