All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v6 net-next 0/5] add PLCA RS support and onsemi NCN26000
@ 2022-12-10 22:45 Piergiorgio Beruto
  2022-12-10 22:46 ` [PATCH v6 net-next 1/5] net/ethtool: add netlink interface for the PLCA RS Piergiorgio Beruto
                   ` (4 more replies)
  0 siblings, 5 replies; 13+ messages in thread
From: Piergiorgio Beruto @ 2022-12-10 22:45 UTC (permalink / raw)
  To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
	Eric Dumazet, Jakub Kicinski, Paolo Abeni
  Cc: linux-kernel, netdev, Oleksij Rempel

This patchset adds support for getting/setting the Physical Layer 
Collision Avoidace (PLCA) Reconciliation Sublayer (RS) configuration and
status on Ethernet PHYs that supports it.

PLCA is a feature that provides improved media-access performance in terms
of throughput, latency and fairness for multi-drop (P2MP) half-duplex PHYs.
PLCA is defined in Clause 148 of the IEEE802.3 specifications as amended
by 802.3cg-2019. Currently, PLCA is supported by the 10BASE-T1S single-pair
Ethernet PHY defined in the same standard and related amendments. The OPEN
Alliance SIG TC14 defines additional specifications for the 10BASE-T1S PHY,
including a standard register map for PHYs that embeds the PLCA RS (see
PLCA management registers at https://www.opensig.org/about/specifications/).

The changes proposed herein add the appropriate ethtool netlink interface
for configuring the PLCA RS on PHYs that supports it. A separate patchset
further modifies the ethtool userspace program to show and modify the
configuration/status of the PLCA RS.

Additionally, this patchset adds support for the onsemi NCN26000
Industrial Ethernet 10BASE-T1S PHY that uses the newly added PLCA
infrastructure.

Piergiorgio Beruto (5):
  net/ethtool: add netlink interface for the PLCA RS
  drivers/net/phy: add the link modes for the 10BASE-T1S Ethernet PHY
  drivers/net/phy: add connection between ethtool and phylib for PLCA
  drivers/net/phy: add helpers to get/set PLCA configuration
  drivers/net/phy: add driver for the onsemi NCN26000 10BASE-T1S PHY

 Documentation/networking/ethtool-netlink.rst | 138 ++++++++++
 MAINTAINERS                                  |  14 +
 drivers/net/phy/Kconfig                      |   7 +
 drivers/net/phy/Makefile                     |   1 +
 drivers/net/phy/mdio-open-alliance.h         |  47 ++++
 drivers/net/phy/ncn26000.c                   | 171 ++++++++++++
 drivers/net/phy/phy-c45.c                    | 183 +++++++++++++
 drivers/net/phy/phy-core.c                   |   5 +-
 drivers/net/phy/phy.c                        | 175 ++++++++++++
 drivers/net/phy/phy_device.c                 |  17 ++
 drivers/net/phy/phylink.c                    |   6 +-
 include/linux/ethtool.h                      |  12 +
 include/linux/phy.h                          |  83 ++++++
 include/uapi/linux/ethtool.h                 |   3 +
 include/uapi/linux/ethtool_netlink.h         |  25 ++
 net/ethtool/Makefile                         |   2 +-
 net/ethtool/common.c                         |   8 +
 net/ethtool/netlink.c                        |  29 ++
 net/ethtool/netlink.h                        |   6 +
 net/ethtool/plca.c                           | 272 +++++++++++++++++++
 20 files changed, 1201 insertions(+), 3 deletions(-)
 create mode 100644 drivers/net/phy/mdio-open-alliance.h
 create mode 100644 drivers/net/phy/ncn26000.c
 create mode 100644 net/ethtool/plca.c

-- 
2.37.4


^ permalink raw reply	[flat|nested] 13+ messages in thread
* [PATCH v6 net-next 1/5] net/ethtool: add netlink interface for the PLCA RS
  2022-12-10 22:45 [PATCH v6 net-next 0/5] add PLCA RS support and onsemi NCN26000 Piergiorgio Beruto
@ 2022-12-10 22:46 ` Piergiorgio Beruto
  2022-12-10 22:46 ` [PATCH v6 net-next 2/5] drivers/net/phy: add the link modes for the 10BASE-T1S Ethernet PHY Piergiorgio Beruto
                   ` (3 subsequent siblings)
  4 siblings, 0 replies; 13+ messages in thread
From: Piergiorgio Beruto @ 2022-12-10 22:46 UTC (permalink / raw)
  To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
	Eric Dumazet, Jakub Kicinski, Paolo Abeni
  Cc: linux-kernel, netdev, Oleksij Rempel

Add support for configuring the PLCA Reconciliation Sublayer on
multi-drop PHYs that support IEEE802.3cg-2019 Clause 148 (e.g.,
10BASE-T1S). This patch adds the appropriate netlink interface
to ethtool.

Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
---
 Documentation/networking/ethtool-netlink.rst | 138 ++++++++++
 MAINTAINERS                                  |   6 +
 include/linux/ethtool.h                      |  12 +
 include/linux/phy.h                          |  57 ++++
 include/uapi/linux/ethtool_netlink.h         |  25 ++
 net/ethtool/Makefile                         |   2 +-
 net/ethtool/netlink.c                        |  29 ++
 net/ethtool/netlink.h                        |   6 +
 net/ethtool/plca.c                           | 272 +++++++++++++++++++
 9 files changed, 546 insertions(+), 1 deletion(-)
 create mode 100644 net/ethtool/plca.c

diff --git a/Documentation/networking/ethtool-netlink.rst b/Documentation/networking/ethtool-netlink.rst
index f10f8eb44255..c59b542eb693 100644
--- a/Documentation/networking/ethtool-netlink.rst
+++ b/Documentation/networking/ethtool-netlink.rst
@@ -1716,6 +1716,141 @@ being used. Current supported options are toeplitz, xor or crc32.
 ETHTOOL_A_RSS_INDIR attribute returns RSS indrection table where each byte
 indicates queue number.
 
+PLCA_GET_CFG
+============
+
+Gets the IEEE 802.3cg-2019 Clause 148 Physical Layer Collision Avoidance
+(PLCA) Reconciliation Sublayer (RS) attributes.
+
+Request contents:
+
+  =====================================  ======  ==========================
+  ``ETHTOOL_A_PLCA_HEADER``              nested  request header
+  =====================================  ======  ==========================
+
+Kernel response contents:
+
+  ======================================  ======  =============================
+  ``ETHTOOL_A_PLCA_HEADER``               nested  reply header
+  ``ETHTOOL_A_PLCA_VERSION``              u16     Supported PLCA management
+                                                  interface standard/version
+  ``ETHTOOL_A_PLCA_ENABLED``              u8      PLCA Admin State
+  ``ETHTOOL_A_PLCA_NODE_ID``              u32     PLCA unique local node ID
+  ``ETHTOOL_A_PLCA_NODE_CNT``             u32     Number of PLCA nodes on the
+                                                  network, including the
+                                                  coordinator
+  ``ETHTOOL_A_PLCA_TO_TMR``               u32     Transmit Opportunity Timer
+                                                  value in bit-times (BT)
+  ``ETHTOOL_A_PLCA_BURST_CNT``            u32     Number of additional packets
+                                                  the node is allowed to send
+                                                  within a single TO
+  ``ETHTOOL_A_PLCA_BURST_TMR``            u32     Time to wait for the MAC to
+                                                  transmit a new frame before
+                                                  terminating the burst
+  ======================================  ======  =============================
+
+When set, the optional ``ETHTOOL_A_PLCA_VERSION`` attribute indicates which
+standard and version the PLCA management interface complies to. When not set,
+the interface is vendor-specific and (possibly) supplied by the driver.
+The OPEN Alliance SIG specifies a standard register map for 10BASE-T1S PHYs
+embedding the PLCA Reconcialiation Sublayer. See "10BASE-T1S PLCA Management
+Registers" at https://www.opensig.org/about/specifications/.
+
+When set, the optional ``ETHTOOL_A_PLCA_ENABLED`` attribute indicates the
+administrative state of the PLCA RS. When not set, the node operates in "plain"
+CSMA/CD mode. This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.1
+aPLCAAdminState / 30.16.1.2.1 acPLCAAdminControl.
+
+When set, the optional ``ETHTOOL_A_PLCA_NODE_ID`` attribute indicates the
+configured local node ID of the PHY. This ID determines which transmit
+opportunity (TO) is reserved for the node to transmit into. This option is
+corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.4 aPLCALocalNodeID. The valid
+range for this attribute is [0 .. 255] where 255 means "not configured".
+
+When set, the optional ``ETHTOOL_A_PLCA_NODE_CNT`` attribute indicates the
+configured maximum number of PLCA nodes on the mixing-segment. This number
+determines the total number of transmit opportunities generated during a
+PLCA cycle. This attribute is relevant only for the PLCA coordinator, which is
+the node with aPLCALocalNodeID set to 0. Follower nodes ignore this setting.
+This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.3
+aPLCANodeCount. The valid range for this attribute is [1 .. 255].
+
+When set, the optional ``ETHTOOL_A_PLCA_TO_TMR`` attribute indicates the
+configured value of the transmit opportunity timer in bit-times. This value
+must be set equal across all nodes sharing the medium for PLCA to work
+correctly. This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.5
+aPLCATransmitOpportunityTimer. The valid range for this attribute is
+[0 .. 255].
+
+When set, the optional ``ETHTOOL_A_PLCA_BURST_CNT`` attribute indicates the
+configured number of extra packets that the node is allowed to send during a
+single transmit opportunity. By default, this attribute is 0, meaning that
+the node can only send a sigle frame per TO. When greater than 0, the PLCA RS
+keeps the TO after any transmission, waiting for the MAC to send a new frame
+for up to aPLCABurstTimer BTs. This can only happen a number of times per PLCA
+cycle up to the value of this parameter. After that, the burst is over and the
+normal counting of TOs resumes. This option is corresponding to
+``IEEE 802.3cg-2019`` 30.16.1.1.6 aPLCAMaxBurstCount. The valid range for this
+attribute is [0 .. 255].
+
+When set, the optional ``ETHTOOL_A_PLCA_BURST_TMR`` attribute indicates how
+many bit-times the PLCA RS waits for the MAC to initiate a new transmission
+when aPLCAMaxBurstCount is greater than 0. If the MAC fails to send a new
+frame within this time, the burst ends and the counting of TOs resumes.
+Otherwise, the new frame is sent as part of the current burst. This option
+is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.7 aPLCABurstTimer. The
+valid range for this attribute is [0 .. 255]. Although, the value should be
+set greater than the Inter-Frame-Gap (IFG) time of the MAC (plus some margin)
+for PLCA burst mode to work as intended.
+
+PLCA_SET_CFG
+============
+
+Sets PLCA RS parameters.
+
+Request contents:
+
+  ======================================  ======  =============================
+  ``ETHTOOL_A_PLCA_HEADER``               nested  request header
+  ``ETHTOOL_A_PLCA_ENABLED``              u8      PLCA Admin State
+  ``ETHTOOL_A_PLCA_NODE_ID``              u8      PLCA unique local node ID
+  ``ETHTOOL_A_PLCA_NODE_CNT``             u8      Number of PLCA nodes on the
+                                                  netkork, including the
+                                                  coordinator
+  ``ETHTOOL_A_PLCA_TO_TMR``               u8      Transmit Opportunity Timer
+                                                  value in bit-times (BT)
+  ``ETHTOOL_A_PLCA_BURST_CNT``            u8      Number of additional packets
+                                                  the node is allowed to send
+                                                  within a single TO
+  ``ETHTOOL_A_PLCA_BURST_TMR``            u8      Time to wait for the MAC to
+                                                  transmit a new frame before
+                                                  terminating the burst
+  ======================================  ======  =============================
+
+For a description of each attribute, see ``PLCA_GET_CFG``.
+
+PLCA_GET_STATUS
+===============
+
+Gets PLCA RS status information.
+
+Request contents:
+
+  =====================================  ======  ==========================
+  ``ETHTOOL_A_PLCA_HEADER``              nested  request header
+  =====================================  ======  ==========================
+
+Kernel response contents:
+
+  ======================================  ======  =============================
+  ``ETHTOOL_A_PLCA_HEADER``               nested  reply header
+  ``ETHTOOL_A_PLCA_STATUS``               u8      PLCA RS operational status
+  ======================================  ======  =============================
+
+When set, the ``ETHTOOL_A_PLCA_STATUS`` attribute indicates whether the node is
+detecting the presence of the BEACON on the network. This flag is
+corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.2 aPLCAStatus.
+
 Request translation
 ===================
 
@@ -1817,4 +1952,7 @@ are netlink only.
   n/a                                 ``ETHTOOL_MSG_PHC_VCLOCKS_GET``
   n/a                                 ``ETHTOOL_MSG_MODULE_GET``
   n/a                                 ``ETHTOOL_MSG_MODULE_SET``
+  n/a                                 ``ETHTOOL_MSG_PLCA_GET_CFG``
+  n/a                                 ``ETHTOOL_MSG_PLCA_SET_CFG``
+  n/a                                 ``ETHTOOL_MSG_PLCA_GET_STATUS``
   =================================== =====================================
diff --git a/MAINTAINERS b/MAINTAINERS
index 955c1be1efb2..7952243e4b43 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -16396,6 +16396,12 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.yaml
 F:	drivers/iio/chemical/pms7003.c
 
+PLCA RECONCILIATION SUBLAYER (IEEE802.3 Clause 148)
+M:	Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	net/ethtool/plca.c
+
 PLDMFW LIBRARY
 M:	Jacob Keller <jacob.e.keller@intel.com>
 S:	Maintained
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index 9e0a76fc7de9..d0da303f6634 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -802,12 +802,17 @@ int ethtool_virtdev_set_link_ksettings(struct net_device *dev,
 
 struct phy_device;
 struct phy_tdr_config;
+struct phy_plca_cfg;
+struct phy_plca_status;
 
 /**
  * struct ethtool_phy_ops - Optional PHY device options
  * @get_sset_count: Get number of strings that @get_strings will write.
  * @get_strings: Return a set of strings that describe the requested objects
  * @get_stats: Return extended statistics about the PHY device.
+ * @get_plca_cfg: Return PLCA configuration.
+ * @set_plca_cfg: Set PLCA configuration.
+ * @get_plca_status: Get PLCA configuration.
  * @start_cable_test: Start a cable test
  * @start_cable_test_tdr: Start a Time Domain Reflectometry cable test
  *
@@ -819,6 +824,13 @@ struct ethtool_phy_ops {
 	int (*get_strings)(struct phy_device *dev, u8 *data);
 	int (*get_stats)(struct phy_device *dev,
 			 struct ethtool_stats *stats, u64 *data);
+	int (*get_plca_cfg)(struct phy_device *dev,
+			    struct phy_plca_cfg *plca_cfg);
+	int (*set_plca_cfg)(struct phy_device *dev,
+			    const struct phy_plca_cfg *plca_cfg,
+			    struct netlink_ext_ack *extack);
+	int (*get_plca_status)(struct phy_device *dev,
+			       struct phy_plca_status *plca_st);
 	int (*start_cable_test)(struct phy_device *phydev,
 				struct netlink_ext_ack *extack);
 	int (*start_cable_test_tdr)(struct phy_device *phydev,
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 71eeb4e3b1fd..c2c04b989cc2 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -765,6 +765,63 @@ struct phy_tdr_config {
 };
 #define PHY_PAIR_ALL -1
 
+/**
+ * struct phy_plca_cfg - Configuration of the PLCA (Physical Layer Collision
+ * Avoidance) Reconciliation Sublayer.
+ *
+ * @version: read-only PLCA register map version. -1 = not available. Ignored
+ *   when setting the configuration. Format is the same as reported by the PLCA
+ *   IDVER register (31.CA00). -1 = not available.
+ * @enabled: PLCA configured mode (enabled/disabled). -1 = not available / don't
+ *   set. 0 = disabled, anything else = enabled.
+ * @node_id: the PLCA local node identifier. -1 = not available / don't set.
+ *   Allowed values [0 .. 254]. 255 = node disabled.
+ * @node_cnt: the PLCA node count (maximum number of nodes having a TO). Only
+ *   meaningful for the coordinator (node_id = 0). -1 = not available / don't
+ *   set. Allowed values [1 .. 255].
+ * @to_tmr: The value of the PLCA to_timer in bit-times, which determines the
+ *   PLCA transmit opportunity window opening. See IEEE802.3 Clause 148 for
+ *   more details. The to_timer shall be set equal over all nodes.
+ *   -1 = not available / don't set. Allowed values [0 .. 255].
+ * @burst_cnt: controls how many additional frames a node is allowed to send in
+ *   single transmit opportunity (TO). The default value of 0 means that the
+ *   node is allowed exactly one frame per TO. A value of 1 allows two frames
+ *   per TO, and so on. -1 = not available / don't set.
+ *   Allowed values [0 .. 255].
+ * @burst_tmr: controls how many bit times to wait for the MAC to send a new
+ *   frame before interrupting the burst. This value should be set to a value
+ *   greater than the MAC inter-packet gap (which is typically 96 bits).
+ *   -1 = not available / don't set. Allowed values [0 .. 255].
+ *
+ * A structure containing configuration parameters for setting/getting the PLCA
+ * RS configuration. The driver does not need to implement all the parameters,
+ * but should report what is actually used.
+ */
+struct phy_plca_cfg {
+	int version;
+	int enabled;
+	int node_id;
+	int node_cnt;
+	int to_tmr;
+	int burst_cnt;
+	int burst_tmr;
+};
+
+/**
+ * struct phy_plca_status - Status of the PLCA (Physical Layer Collision
+ * Avoidance) Reconciliation Sublayer.
+ *
+ * @pst: The PLCA status as reported by the PST bit in the PLCA STATUS
+ *	register(31.CA03), indicating BEACON activity.
+ *
+ * A structure containing status information of the PLCA RS configuration.
+ * The driver does not need to implement all the parameters, but should report
+ * what is actually used.
+ */
+struct phy_plca_status {
+	bool pst;
+};
+
 /**
  * struct phy_driver - Driver structure for a particular PHY type
  *
diff --git a/include/uapi/linux/ethtool_netlink.h b/include/uapi/linux/ethtool_netlink.h
index 5799a9db034e..d6913620739b 100644
--- a/include/uapi/linux/ethtool_netlink.h
+++ b/include/uapi/linux/ethtool_netlink.h
@@ -52,6 +52,9 @@ enum {
 	ETHTOOL_MSG_PSE_GET,
 	ETHTOOL_MSG_PSE_SET,
 	ETHTOOL_MSG_RSS_GET,
+	ETHTOOL_MSG_PLCA_GET_CFG,
+	ETHTOOL_MSG_PLCA_SET_CFG,
+	ETHTOOL_MSG_PLCA_GET_STATUS,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_USER_CNT,
@@ -99,6 +102,9 @@ enum {
 	ETHTOOL_MSG_MODULE_NTF,
 	ETHTOOL_MSG_PSE_GET_REPLY,
 	ETHTOOL_MSG_RSS_GET_REPLY,
+	ETHTOOL_MSG_PLCA_GET_CFG_REPLY,
+	ETHTOOL_MSG_PLCA_GET_STATUS_REPLY,
+	ETHTOOL_MSG_PLCA_NTF,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_KERNEL_CNT,
@@ -894,6 +900,25 @@ enum {
 	ETHTOOL_A_RSS_MAX = (__ETHTOOL_A_RSS_CNT - 1),
 };
 
+/* PLCA */
+
+enum {
+	ETHTOOL_A_PLCA_UNSPEC,
+	ETHTOOL_A_PLCA_HEADER,			/* nest - _A_HEADER_* */
+	ETHTOOL_A_PLCA_VERSION,			/* u16 */
+	ETHTOOL_A_PLCA_ENABLED,			/* u32 */
+	ETHTOOL_A_PLCA_STATUS,			/* u32 */
+	ETHTOOL_A_PLCA_NODE_CNT,		/* u32 */
+	ETHTOOL_A_PLCA_NODE_ID,			/* u32 */
+	ETHTOOL_A_PLCA_TO_TMR,			/* u32 */
+	ETHTOOL_A_PLCA_BURST_CNT,		/* u32 */
+	ETHTOOL_A_PLCA_BURST_TMR,		/* u32 */
+
+	/* add new constants above here */
+	__ETHTOOL_A_PLCA_CNT,
+	ETHTOOL_A_PLCA_MAX = (__ETHTOOL_A_PLCA_CNT - 1)
+};
+
 /* generic netlink info */
 #define ETHTOOL_GENL_NAME "ethtool"
 #define ETHTOOL_GENL_VERSION 1
diff --git a/net/ethtool/Makefile b/net/ethtool/Makefile
index 228f13df2e18..563864c1bf5a 100644
--- a/net/ethtool/Makefile
+++ b/net/ethtool/Makefile
@@ -8,4 +8,4 @@ ethtool_nl-y	:= netlink.o bitset.o strset.o linkinfo.o linkmodes.o rss.o \
 		   linkstate.o debug.o wol.o features.o privflags.o rings.o \
 		   channels.o coalesce.o pause.o eee.o tsinfo.o cabletest.o \
 		   tunnels.o fec.o eeprom.o stats.o phc_vclocks.o module.o \
-		   pse-pd.o
+		   pse-pd.o plca.o
diff --git a/net/ethtool/netlink.c b/net/ethtool/netlink.c
index aee98be6237f..9f924875bba9 100644
--- a/net/ethtool/netlink.c
+++ b/net/ethtool/netlink.c
@@ -288,6 +288,8 @@ ethnl_default_requests[__ETHTOOL_MSG_USER_CNT] = {
 	[ETHTOOL_MSG_MODULE_GET]	= &ethnl_module_request_ops,
 	[ETHTOOL_MSG_PSE_GET]		= &ethnl_pse_request_ops,
 	[ETHTOOL_MSG_RSS_GET]		= &ethnl_rss_request_ops,
+	[ETHTOOL_MSG_PLCA_GET_CFG]	= &ethnl_plca_cfg_request_ops,
+	[ETHTOOL_MSG_PLCA_GET_STATUS]	= &ethnl_plca_status_request_ops,
 };
 
 static struct ethnl_dump_ctx *ethnl_dump_context(struct netlink_callback *cb)
@@ -603,6 +605,7 @@ ethnl_default_notify_ops[ETHTOOL_MSG_KERNEL_MAX + 1] = {
 	[ETHTOOL_MSG_EEE_NTF]		= &ethnl_eee_request_ops,
 	[ETHTOOL_MSG_FEC_NTF]		= &ethnl_fec_request_ops,
 	[ETHTOOL_MSG_MODULE_NTF]	= &ethnl_module_request_ops,
+	[ETHTOOL_MSG_PLCA_NTF]		= &ethnl_plca_cfg_request_ops,
 };
 
 /* default notification handler */
@@ -696,6 +699,7 @@ static const ethnl_notify_handler_t ethnl_notify_handlers[] = {
 	[ETHTOOL_MSG_EEE_NTF]		= ethnl_default_notify,
 	[ETHTOOL_MSG_FEC_NTF]		= ethnl_default_notify,
 	[ETHTOOL_MSG_MODULE_NTF]	= ethnl_default_notify,
+	[ETHTOOL_MSG_PLCA_NTF]		= ethnl_default_notify,
 };
 
 void ethtool_notify(struct net_device *dev, unsigned int cmd, const void *data)
@@ -1047,6 +1051,31 @@ static const struct genl_ops ethtool_genl_ops[] = {
 		.policy = ethnl_rss_get_policy,
 		.maxattr = ARRAY_SIZE(ethnl_rss_get_policy) - 1,
 	},
+	{
+		.cmd	= ETHTOOL_MSG_PLCA_GET_CFG,
+		.doit	= ethnl_default_doit,
+		.start	= ethnl_default_start,
+		.dumpit	= ethnl_default_dumpit,
+		.done	= ethnl_default_done,
+		.policy = ethnl_plca_get_cfg_policy,
+		.maxattr = ARRAY_SIZE(ethnl_plca_get_cfg_policy) - 1,
+	},
+	{
+		.cmd	= ETHTOOL_MSG_PLCA_SET_CFG,
+		.flags	= GENL_UNS_ADMIN_PERM,
+		.doit	= ethnl_set_plca_cfg,
+		.policy = ethnl_plca_set_cfg_policy,
+		.maxattr = ARRAY_SIZE(ethnl_plca_set_cfg_policy) - 1,
+	},
+	{
+		.cmd	= ETHTOOL_MSG_PLCA_GET_STATUS,
+		.doit	= ethnl_default_doit,
+		.start	= ethnl_default_start,
+		.dumpit	= ethnl_default_dumpit,
+		.done	= ethnl_default_done,
+		.policy = ethnl_plca_get_status_policy,
+		.maxattr = ARRAY_SIZE(ethnl_plca_get_status_policy) - 1,
+	},
 };
 
 static const struct genl_multicast_group ethtool_nl_mcgrps[] = {
diff --git a/net/ethtool/netlink.h b/net/ethtool/netlink.h
index 3753787ba233..f271266f6e28 100644
--- a/net/ethtool/netlink.h
+++ b/net/ethtool/netlink.h
@@ -347,6 +347,8 @@ extern const struct ethnl_request_ops ethnl_phc_vclocks_request_ops;
 extern const struct ethnl_request_ops ethnl_module_request_ops;
 extern const struct ethnl_request_ops ethnl_pse_request_ops;
 extern const struct ethnl_request_ops ethnl_rss_request_ops;
+extern const struct ethnl_request_ops ethnl_plca_cfg_request_ops;
+extern const struct ethnl_request_ops ethnl_plca_status_request_ops;
 
 extern const struct nla_policy ethnl_header_policy[ETHTOOL_A_HEADER_FLAGS + 1];
 extern const struct nla_policy ethnl_header_policy_stats[ETHTOOL_A_HEADER_FLAGS + 1];
@@ -388,6 +390,9 @@ extern const struct nla_policy ethnl_module_set_policy[ETHTOOL_A_MODULE_POWER_MO
 extern const struct nla_policy ethnl_pse_get_policy[ETHTOOL_A_PSE_HEADER + 1];
 extern const struct nla_policy ethnl_pse_set_policy[ETHTOOL_A_PSE_MAX + 1];
 extern const struct nla_policy ethnl_rss_get_policy[ETHTOOL_A_RSS_CONTEXT + 1];
+extern const struct nla_policy ethnl_plca_get_cfg_policy[ETHTOOL_A_PLCA_HEADER + 1];
+extern const struct nla_policy ethnl_plca_set_cfg_policy[ETHTOOL_A_PLCA_MAX + 1];
+extern const struct nla_policy ethnl_plca_get_status_policy[ETHTOOL_A_PLCA_HEADER + 1];
 
 int ethnl_set_linkinfo(struct sk_buff *skb, struct genl_info *info);
 int ethnl_set_linkmodes(struct sk_buff *skb, struct genl_info *info);
@@ -408,6 +413,7 @@ int ethnl_tunnel_info_dumpit(struct sk_buff *skb, struct netlink_callback *cb);
 int ethnl_set_fec(struct sk_buff *skb, struct genl_info *info);
 int ethnl_set_module(struct sk_buff *skb, struct genl_info *info);
 int ethnl_set_pse(struct sk_buff *skb, struct genl_info *info);
+int ethnl_set_plca_cfg(struct sk_buff *skb, struct genl_info *info);
 
 extern const char stats_std_names[__ETHTOOL_STATS_CNT][ETH_GSTRING_LEN];
 extern const char stats_eth_phy_names[__ETHTOOL_A_STATS_ETH_PHY_CNT][ETH_GSTRING_LEN];
diff --git a/net/ethtool/plca.c b/net/ethtool/plca.c
new file mode 100644
index 000000000000..b39e1a3ac469
--- /dev/null
+++ b/net/ethtool/plca.c
@@ -0,0 +1,272 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/phy.h>
+#include <linux/ethtool_netlink.h>
+
+#include "netlink.h"
+#include "common.h"
+
+struct plca_req_info {
+	struct ethnl_req_info		base;
+};
+
+struct plca_reply_data {
+	struct ethnl_reply_data		base;
+	struct phy_plca_cfg		plca_cfg;
+	struct phy_plca_status		plca_st;
+};
+
+
+// Helpers ------------------------------------------------------------------ //
+
+#define PLCA_REPDATA(__reply_base) \
+	container_of(__reply_base, struct plca_reply_data, base)
+
+static inline void plca_update_sint(int *dst, const struct nlattr *attr,
+				    bool *mod)
+{
+	if (attr) {
+		*dst = nla_get_u32(attr);
+		*mod = true;
+	}
+}
+
+// PLCA get configuration message ------------------------------------------- //
+
+const struct nla_policy ethnl_plca_get_cfg_policy[] = {
+	[ETHTOOL_A_PLCA_HEADER]		=
+		NLA_POLICY_NESTED(ethnl_header_policy),
+};
+
+static int plca_get_cfg_prepare_data(const struct ethnl_req_info *req_base,
+				     struct ethnl_reply_data *reply_base,
+				     struct genl_info *info)
+{
+	struct plca_reply_data *data = PLCA_REPDATA(reply_base);
+	struct net_device *dev = reply_base->dev;
+	const struct ethtool_phy_ops *ops;
+	int ret;
+
+	// check that the PHY device is available and connected
+	if (!dev->phydev) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	// note: rtnl_lock is held already by ethnl_default_doit
+	ops = ethtool_phy_ops;
+	if (!ops || !ops->get_plca_cfg) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	ret = ethnl_ops_begin(dev);
+	if (ret < 0)
+		goto out;
+
+	ret = ops->get_plca_cfg(dev->phydev, &data->plca_cfg);
+	ethnl_ops_complete(dev);
+
+out:
+	return ret;
+}
+
+static int plca_get_cfg_reply_size(const struct ethnl_req_info *req_base,
+				   const struct ethnl_reply_data *reply_base)
+{
+	return nla_total_size(sizeof(u16)) +	/* _VERSION */
+	       nla_total_size(sizeof(u8)) +	/* _ENABLED */
+	       nla_total_size(sizeof(u8)) +	/* _STATUS  */
+	       nla_total_size(sizeof(u8)) +	/* _NODE_CNT */
+	       nla_total_size(sizeof(u8)) +	/* _NODE_ID */
+	       nla_total_size(sizeof(u8)) +	/* _TO_TIMER */
+	       nla_total_size(sizeof(u8)) +	/* _BURST_COUNT */
+	       nla_total_size(sizeof(u8));	/* _BURST_TIMER */
+}
+
+static int plca_get_cfg_fill_reply(struct sk_buff *skb,
+				   const struct ethnl_req_info *req_base,
+				   const struct ethnl_reply_data *reply_base)
+{
+	const struct plca_reply_data *data = PLCA_REPDATA(reply_base);
+	const struct phy_plca_cfg *plca = &data->plca_cfg;
+
+	if ((plca->version >= 0 &&
+	     nla_put_u16(skb, ETHTOOL_A_PLCA_VERSION, plca->version)) ||
+	    (plca->enabled >= 0 &&
+	     nla_put_u8(skb, ETHTOOL_A_PLCA_ENABLED, !!plca->enabled)) ||
+	    (plca->node_id >= 0 &&
+	     nla_put_u32(skb, ETHTOOL_A_PLCA_NODE_ID, plca->node_id)) ||
+	    (plca->node_cnt >= 0 &&
+	     nla_put_u32(skb, ETHTOOL_A_PLCA_NODE_CNT, plca->node_cnt)) ||
+	    (plca->to_tmr >= 0 &&
+	     nla_put_u32(skb, ETHTOOL_A_PLCA_TO_TMR, plca->to_tmr)) ||
+	    (plca->burst_cnt >= 0 &&
+	     nla_put_u32(skb, ETHTOOL_A_PLCA_BURST_CNT, plca->burst_cnt)) ||
+	    (plca->burst_tmr >= 0 &&
+	     nla_put_u32(skb, ETHTOOL_A_PLCA_BURST_TMR, plca->burst_tmr)))
+		return -EMSGSIZE;
+
+	return 0;
+};
+
+const struct ethnl_request_ops ethnl_plca_cfg_request_ops = {
+	.request_cmd		= ETHTOOL_MSG_PLCA_GET_CFG,
+	.reply_cmd		= ETHTOOL_MSG_PLCA_GET_CFG_REPLY,
+	.hdr_attr		= ETHTOOL_A_PLCA_HEADER,
+	.req_info_size		= sizeof(struct plca_req_info),
+	.reply_data_size	= sizeof(struct plca_reply_data),
+
+	.prepare_data		= plca_get_cfg_prepare_data,
+	.reply_size		= plca_get_cfg_reply_size,
+	.fill_reply		= plca_get_cfg_fill_reply,
+};
+
+// PLCA set configuration message ------------------------------------------- //
+
+const struct nla_policy ethnl_plca_set_cfg_policy[] = {
+	[ETHTOOL_A_PLCA_HEADER]		=
+		NLA_POLICY_NESTED(ethnl_header_policy),
+	[ETHTOOL_A_PLCA_ENABLED]	= NLA_POLICY_MAX(NLA_U8, 1),
+	[ETHTOOL_A_PLCA_NODE_ID]	= NLA_POLICY_MAX(NLA_U32, 255),
+	[ETHTOOL_A_PLCA_NODE_CNT]	= NLA_POLICY_RANGE(NLA_U32, 1, 255),
+	[ETHTOOL_A_PLCA_TO_TMR]		= NLA_POLICY_MAX(NLA_U32, 255),
+	[ETHTOOL_A_PLCA_BURST_CNT]	= NLA_POLICY_MAX(NLA_U32, 255),
+	[ETHTOOL_A_PLCA_BURST_TMR]	= NLA_POLICY_MAX(NLA_U32, 255),
+};
+
+int ethnl_set_plca_cfg(struct sk_buff *skb, struct genl_info *info)
+{
+	struct ethnl_req_info req_info = {};
+	struct nlattr **tb = info->attrs;
+	const struct ethtool_phy_ops *ops;
+	struct phy_plca_cfg plca_cfg;
+	struct net_device *dev;
+	bool mod = false;
+	int ret;
+
+	ret = ethnl_parse_header_dev_get(&req_info,
+					 tb[ETHTOOL_A_PLCA_HEADER],
+					 genl_info_net(info), info->extack,
+					 true);
+	if (ret < 0)
+		return ret;
+
+	dev = req_info.dev;
+
+	rtnl_lock();
+
+	// check that the PHY device is available and connected
+	if (!dev->phydev) {
+		ret = -EOPNOTSUPP;
+		goto out_rtnl;
+	}
+
+	ops = ethtool_phy_ops;
+	if (!ops || !ops->set_plca_cfg) {
+		ret = -EOPNOTSUPP;
+		goto out_rtnl;
+	}
+
+	ret = ethnl_ops_begin(dev);
+	if (ret < 0)
+		goto out_rtnl;
+
+	memset(&plca_cfg, 0xFF, sizeof(plca_cfg));
+	plca_update_sint(&plca_cfg.enabled, tb[ETHTOOL_A_PLCA_ENABLED], &mod);
+	plca_update_sint(&plca_cfg.node_id, tb[ETHTOOL_A_PLCA_NODE_ID], &mod);
+	plca_update_sint(&plca_cfg.node_cnt, tb[ETHTOOL_A_PLCA_NODE_CNT], &mod);
+	plca_update_sint(&plca_cfg.to_tmr, tb[ETHTOOL_A_PLCA_TO_TMR], &mod);
+	plca_update_sint(&plca_cfg.burst_cnt, tb[ETHTOOL_A_PLCA_BURST_CNT],
+			 &mod);
+	plca_update_sint(&plca_cfg.burst_tmr, tb[ETHTOOL_A_PLCA_BURST_TMR],
+			 &mod);
+
+	ret = 0;
+	if (!mod)
+		goto out_ops;
+
+	ret = ops->set_plca_cfg(dev->phydev, &plca_cfg, info->extack);
+	if (ret < 0)
+		goto out_ops;
+
+	ethtool_notify(dev, ETHTOOL_MSG_PLCA_NTF, NULL);
+
+out_ops:
+	ethnl_ops_complete(dev);
+out_rtnl:
+	rtnl_unlock();
+	ethnl_parse_header_dev_put(&req_info);
+
+	return ret;
+}
+
+// PLCA get status message -------------------------------------------------- //
+
+const struct nla_policy ethnl_plca_get_status_policy[] = {
+	[ETHTOOL_A_PLCA_HEADER]		=
+		NLA_POLICY_NESTED(ethnl_header_policy),
+};
+
+static int plca_get_status_prepare_data(const struct ethnl_req_info *req_base,
+					struct ethnl_reply_data *reply_base,
+					struct genl_info *info)
+{
+	struct plca_reply_data *data = PLCA_REPDATA(reply_base);
+	struct net_device *dev = reply_base->dev;
+	const struct ethtool_phy_ops *ops;
+	int ret;
+
+	// check that the PHY device is available and connected
+	if (!dev->phydev) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	// note: rtnl_lock is held already by ethnl_default_doit
+	ops = ethtool_phy_ops;
+	if (!ops || !ops->get_plca_status) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	ret = ethnl_ops_begin(dev);
+	if (ret < 0)
+		goto out;
+
+	ret = ops->get_plca_status(dev->phydev, &data->plca_st);
+	ethnl_ops_complete(dev);
+out:
+	return ret;
+}
+
+static int plca_get_status_reply_size(const struct ethnl_req_info *req_base,
+				      const struct ethnl_reply_data *reply_base)
+{
+	return nla_total_size(sizeof(u8));	/* _STATUS */
+}
+
+static int plca_get_status_fill_reply(struct sk_buff *skb,
+				      const struct ethnl_req_info *req_base,
+				      const struct ethnl_reply_data *reply_base)
+{
+	const struct plca_reply_data *data = PLCA_REPDATA(reply_base);
+	const u8 status = data->plca_st.pst;
+
+	if (nla_put_u8(skb, ETHTOOL_A_PLCA_STATUS, !!status))
+		return -EMSGSIZE;
+
+	return 0;
+};
+
+const struct ethnl_request_ops ethnl_plca_status_request_ops = {
+	.request_cmd		= ETHTOOL_MSG_PLCA_GET_STATUS,
+	.reply_cmd		= ETHTOOL_MSG_PLCA_GET_STATUS_REPLY,
+	.hdr_attr		= ETHTOOL_A_PLCA_HEADER,
+	.req_info_size		= sizeof(struct plca_req_info),
+	.reply_data_size	= sizeof(struct plca_reply_data),
+
+	.prepare_data		= plca_get_status_prepare_data,
+	.reply_size		= plca_get_status_reply_size,
+	.fill_reply		= plca_get_status_fill_reply,
+};
-- 
2.37.4


^ permalink raw reply related	[flat|nested] 13+ messages in thread
* [PATCH v6 net-next 2/5] drivers/net/phy: add the link modes for the 10BASE-T1S Ethernet PHY
  2022-12-10 22:45 [PATCH v6 net-next 0/5] add PLCA RS support and onsemi NCN26000 Piergiorgio Beruto
  2022-12-10 22:46 ` [PATCH v6 net-next 1/5] net/ethtool: add netlink interface for the PLCA RS Piergiorgio Beruto
@ 2022-12-10 22:46 ` Piergiorgio Beruto
  2022-12-10 22:46 ` [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA Piergiorgio Beruto
                   ` (2 subsequent siblings)
  4 siblings, 0 replies; 13+ messages in thread
From: Piergiorgio Beruto @ 2022-12-10 22:46 UTC (permalink / raw)
  To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
	Eric Dumazet, Jakub Kicinski, Paolo Abeni
  Cc: linux-kernel, netdev, Oleksij Rempel

This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S
Ethernet PHY. According to the specifications, the 10BASE-T1S supports
Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or
Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations.

Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
---
 drivers/net/phy/phy-core.c   |  5 ++++-
 drivers/net/phy/phy_device.c | 14 ++++++++++++++
 drivers/net/phy/phylink.c    |  6 +++++-
 include/linux/phy.h          | 13 +++++++++++++
 include/uapi/linux/ethtool.h |  3 +++
 net/ethtool/common.c         |  8 ++++++++
 6 files changed, 47 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/phy-core.c b/drivers/net/phy/phy-core.c
index 5d08c627a516..a64186dc53f8 100644
--- a/drivers/net/phy/phy-core.c
+++ b/drivers/net/phy/phy-core.c
@@ -13,7 +13,7 @@
  */
 const char *phy_speed_to_str(int speed)
 {
-	BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 99,
+	BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 102,
 		"Enum ethtool_link_mode_bit_indices and phylib are out of sync. "
 		"If a speed or mode has been added please update phy_speed_to_str "
 		"and the PHY settings array.\n");
@@ -260,6 +260,9 @@ static const struct phy_setting settings[] = {
 	PHY_SETTING(     10, FULL,     10baseT_Full		),
 	PHY_SETTING(     10, HALF,     10baseT_Half		),
 	PHY_SETTING(     10, FULL,     10baseT1L_Full		),
+	PHY_SETTING(     10, FULL,     10baseT1S_Full		),
+	PHY_SETTING(     10, HALF,     10baseT1S_Half		),
+	PHY_SETTING(     10, HALF,     10baseT1S_P2MP_Half	),
 };
 #undef PHY_SETTING
 
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 716870a4499c..8e48b3cec5e7 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -45,6 +45,9 @@ EXPORT_SYMBOL_GPL(phy_basic_features);
 __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_t1_features) __ro_after_init;
 EXPORT_SYMBOL_GPL(phy_basic_t1_features);
 
+__ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_t1s_p2mp_features) __ro_after_init;
+EXPORT_SYMBOL_GPL(phy_basic_t1s_p2mp_features);
+
 __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_gbit_features) __ro_after_init;
 EXPORT_SYMBOL_GPL(phy_gbit_features);
 
@@ -98,6 +101,12 @@ const int phy_basic_t1_features_array[3] = {
 };
 EXPORT_SYMBOL_GPL(phy_basic_t1_features_array);
 
+const int phy_basic_t1s_p2mp_features_array[2] = {
+	ETHTOOL_LINK_MODE_TP_BIT,
+	ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT,
+};
+EXPORT_SYMBOL_GPL(phy_basic_t1s_p2mp_features_array);
+
 const int phy_gbit_features_array[2] = {
 	ETHTOOL_LINK_MODE_1000baseT_Half_BIT,
 	ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
@@ -138,6 +147,11 @@ static void features_init(void)
 			       ARRAY_SIZE(phy_basic_t1_features_array),
 			       phy_basic_t1_features);
 
+	/* 10 half, P2MP, TP */
+	linkmode_set_bit_array(phy_basic_t1s_p2mp_features_array,
+			       ARRAY_SIZE(phy_basic_t1s_p2mp_features_array),
+			       phy_basic_t1s_p2mp_features);
+
 	/* 10/100 half/full + 1000 half/full */
 	linkmode_set_bit_array(phy_basic_ports_array,
 			       ARRAY_SIZE(phy_basic_ports_array),
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 09cc65c0da93..319790221d7f 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -241,12 +241,16 @@ void phylink_caps_to_linkmodes(unsigned long *linkmodes, unsigned long caps)
 	if (caps & MAC_ASYM_PAUSE)
 		__set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, linkmodes);
 
-	if (caps & MAC_10HD)
+	if (caps & MAC_10HD) {
 		__set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, linkmodes);
+		__set_bit(ETHTOOL_LINK_MODE_10baseT1S_Half_BIT, linkmodes);
+		__set_bit(ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT, linkmodes);
+	}
 
 	if (caps & MAC_10FD) {
 		__set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, linkmodes);
 		__set_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT, linkmodes);
+		__set_bit(ETHTOOL_LINK_MODE_10baseT1S_Full_BIT, linkmodes);
 	}
 
 	if (caps & MAC_100HD) {
diff --git a/include/linux/phy.h b/include/linux/phy.h
index c2c04b989cc2..2a5c2d3a5da5 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -45,6 +45,7 @@
 
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_t1_features) __ro_after_init;
+extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_t1s_p2mp_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_gbit_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_gbit_fibre_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_gbit_all_ports_features) __ro_after_init;
@@ -54,6 +55,7 @@ extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_10gbit_full_features) __ro_after_ini
 
 #define PHY_BASIC_FEATURES ((unsigned long *)&phy_basic_features)
 #define PHY_BASIC_T1_FEATURES ((unsigned long *)&phy_basic_t1_features)
+#define PHY_BASIC_T1S_P2MP_FEATURES ((unsigned long *)&phy_basic_t1s_p2mp_features)
 #define PHY_GBIT_FEATURES ((unsigned long *)&phy_gbit_features)
 #define PHY_GBIT_FIBRE_FEATURES ((unsigned long *)&phy_gbit_fibre_features)
 #define PHY_GBIT_ALL_PORTS_FEATURES ((unsigned long *)&phy_gbit_all_ports_features)
@@ -1036,6 +1038,17 @@ struct phy_driver {
 	int (*get_sqi)(struct phy_device *dev);
 	/** @get_sqi_max: Get the maximum signal quality indication */
 	int (*get_sqi_max)(struct phy_device *dev);
+
+	/* PLCA RS interface */
+	/** @get_plca_cfg: Return the current PLCA configuration */
+	int (*get_plca_cfg)(struct phy_device *dev,
+			    struct phy_plca_cfg *plca_cfg);
+	/** @set_plca_cfg: Set the PLCA configuration */
+	int (*set_plca_cfg)(struct phy_device *dev,
+			    const struct phy_plca_cfg *plca_cfg);
+	/** @get_plca_status: Return the current PLCA status info */
+	int (*get_plca_status)(struct phy_device *dev,
+			       struct phy_plca_status *plca_st);
 };
 #define to_phy_driver(d) container_of(to_mdio_common_driver(d),		\
 				      struct phy_driver, mdiodrv)
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h
index 58e587ba0450..5f414deacf23 100644
--- a/include/uapi/linux/ethtool.h
+++ b/include/uapi/linux/ethtool.h
@@ -1741,6 +1741,9 @@ enum ethtool_link_mode_bit_indices {
 	ETHTOOL_LINK_MODE_800000baseDR8_2_Full_BIT	 = 96,
 	ETHTOOL_LINK_MODE_800000baseSR8_Full_BIT	 = 97,
 	ETHTOOL_LINK_MODE_800000baseVR8_Full_BIT	 = 98,
+	ETHTOOL_LINK_MODE_10baseT1S_Full_BIT		 = 99,
+	ETHTOOL_LINK_MODE_10baseT1S_Half_BIT		 = 100,
+	ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT	 = 101,
 
 	/* must be last entry */
 	__ETHTOOL_LINK_MODE_MASK_NBITS
diff --git a/net/ethtool/common.c b/net/ethtool/common.c
index 6f399afc2ff2..5fb19050991e 100644
--- a/net/ethtool/common.c
+++ b/net/ethtool/common.c
@@ -208,6 +208,9 @@ const char link_mode_names[][ETH_GSTRING_LEN] = {
 	__DEFINE_LINK_MODE_NAME(800000, DR8_2, Full),
 	__DEFINE_LINK_MODE_NAME(800000, SR8, Full),
 	__DEFINE_LINK_MODE_NAME(800000, VR8, Full),
+	__DEFINE_LINK_MODE_NAME(10, T1S, Full),
+	__DEFINE_LINK_MODE_NAME(10, T1S, Half),
+	__DEFINE_LINK_MODE_NAME(10, T1S_P2MP, Half),
 };
 static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 
@@ -244,6 +247,8 @@ static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 #define __LINK_MODE_LANES_X		1
 #define __LINK_MODE_LANES_FX		1
 #define __LINK_MODE_LANES_T1L		1
+#define __LINK_MODE_LANES_T1S		1
+#define __LINK_MODE_LANES_T1S_P2MP	1
 #define __LINK_MODE_LANES_VR8		8
 #define __LINK_MODE_LANES_DR8_2		8
 
@@ -366,6 +371,9 @@ const struct link_mode_info link_mode_params[] = {
 	__DEFINE_LINK_MODE_PARAMS(800000, DR8_2, Full),
 	__DEFINE_LINK_MODE_PARAMS(800000, SR8, Full),
 	__DEFINE_LINK_MODE_PARAMS(800000, VR8, Full),
+	__DEFINE_LINK_MODE_PARAMS(10, T1S, Full),
+	__DEFINE_LINK_MODE_PARAMS(10, T1S, Half),
+	__DEFINE_LINK_MODE_PARAMS(10, T1S_P2MP, Half),
 };
 static_assert(ARRAY_SIZE(link_mode_params) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 
-- 
2.37.4


^ permalink raw reply related	[flat|nested] 13+ messages in thread
* [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA
  2022-12-10 22:45 [PATCH v6 net-next 0/5] add PLCA RS support and onsemi NCN26000 Piergiorgio Beruto
  2022-12-10 22:46 ` [PATCH v6 net-next 1/5] net/ethtool: add netlink interface for the PLCA RS Piergiorgio Beruto
  2022-12-10 22:46 ` [PATCH v6 net-next 2/5] drivers/net/phy: add the link modes for the 10BASE-T1S Ethernet PHY Piergiorgio Beruto
@ 2022-12-10 22:46 ` Piergiorgio Beruto
  2022-12-11 12:05   ` kernel test robot
  2022-12-11 12:23   ` Russell King (Oracle)
  2022-12-10 22:46 ` [PATCH v6 net-next 4/5] drivers/net/phy: add helpers to get/set PLCA configuration Piergiorgio Beruto
  2022-12-10 22:47 ` [PATCH v6 net-next 5/5] drivers/net/phy: add driver for the onsemi NCN26000 10BASE-T1S PHY Piergiorgio Beruto
  4 siblings, 2 replies; 13+ messages in thread
From: Piergiorgio Beruto @ 2022-12-10 22:46 UTC (permalink / raw)
  To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
	Eric Dumazet, Jakub Kicinski, Paolo Abeni
  Cc: linux-kernel, netdev, Oleksij Rempel

This patch adds the required connection between netlink ethtool and
phylib to resolve PLCA get/set config and get status messages.

Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
---
 drivers/net/phy/phy.c        | 175 +++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy_device.c |   3 +
 include/linux/phy.h          |   7 ++
 3 files changed, 185 insertions(+)

diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index e5b6cb1a77f9..40d90ed2f0fb 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -543,6 +543,181 @@ int phy_ethtool_get_stats(struct phy_device *phydev,
 }
 EXPORT_SYMBOL(phy_ethtool_get_stats);
 
+/**
+ * phy_ethtool_get_plca_cfg - Get PLCA RS configuration
+ *
+ * @phydev: the phy_device struct
+ * @plca_cfg: where to store the retrieved configuration
+ */
+int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
+			     struct phy_plca_cfg *plca_cfg)
+{
+	int ret;
+
+	if (!phydev->drv) {
+		ret = -EIO;
+		goto out;
+	}
+
+	if (!phydev->drv->get_plca_cfg) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	memset(plca_cfg, 0xFF, sizeof(*plca_cfg));
+
+	mutex_lock(&phydev->lock);
+	ret = phydev->drv->get_plca_cfg(phydev, plca_cfg);
+
+	if (ret)
+		goto out_drv;
+
+out_drv:
+	mutex_unlock(&phydev->lock);
+out:
+	return ret;
+}
+
+/**
+ * phy_ethtool_set_plca_cfg - Set PLCA RS configuration
+ *
+ * @phydev: the phy_device struct
+ * @extack: extack for reporting useful error messages
+ * @plca_cfg: new PLCA configuration to apply
+ */
+int phy_ethtool_set_plca_cfg(struct phy_device *phydev,
+			     const struct phy_plca_cfg *plca_cfg,
+			     struct netlink_ext_ack *extack)
+{
+	int ret;
+	struct phy_plca_cfg *curr_plca_cfg = 0;
+
+	if (!phydev->drv) {
+		ret = -EIO;
+		goto out;
+	}
+
+	if (!phydev->drv->set_plca_cfg ||
+	    !phydev->drv->get_plca_cfg) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	curr_plca_cfg = kmalloc(sizeof(*curr_plca_cfg), GFP_KERNEL);
+	memset(curr_plca_cfg, 0xFF, sizeof(*curr_plca_cfg));
+
+	mutex_lock(&phydev->lock);
+
+	ret = phydev->drv->get_plca_cfg(phydev, curr_plca_cfg);
+	if (ret)
+		goto out_drv;
+
+	if (curr_plca_cfg->enabled < 0 && plca_cfg->enabled >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'enable' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->node_id < 0 && plca_cfg->node_id >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'local node ID' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->node_cnt < 0 && plca_cfg->node_cnt >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'node count' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->to_tmr < 0 && plca_cfg->to_tmr >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'TO timer' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->burst_cnt < 0 && plca_cfg->burst_cnt >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'burst count' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->burst_tmr < 0 && plca_cfg->burst_tmr >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'burst timer' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	// if enabling PLCA, perform additional sanity checks
+	if (plca_cfg->enabled > 0) {
+		if (!linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT,
+				       phydev->advertising)) {
+			ret = -EOPNOTSUPP;
+			NL_SET_ERR_MSG(extack,
+				       "Point to Multi-Point mode is not enabled");
+		}
+
+		// allow setting node_id concurrently with enabled
+		if (plca_cfg->node_id >= 0)
+			curr_plca_cfg->node_id = plca_cfg->node_id;
+
+		if (curr_plca_cfg->node_id >= 255) {
+			NL_SET_ERR_MSG(extack, "PLCA node ID is not set");
+			ret = -EINVAL;
+			goto out_drv;
+		}
+	}
+
+	ret = phydev->drv->set_plca_cfg(phydev, plca_cfg);
+	if (ret)
+		goto out_drv;
+
+out_drv:
+	kfree(curr_plca_cfg);
+	mutex_unlock(&phydev->lock);
+out:
+	return ret;
+}
+
+/**
+ * phy_ethtool_get_plca_status - Get PLCA RS status information
+ *
+ * @phydev: the phy_device struct
+ * @plca_st: where to store the retrieved status information
+ */
+int phy_ethtool_get_plca_status(struct phy_device *phydev,
+				struct phy_plca_status *plca_st)
+{
+	int ret;
+
+	if (!phydev->drv) {
+		ret = -EIO;
+		goto out;
+	}
+
+	if (!phydev->drv->get_plca_status) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	mutex_lock(&phydev->lock);
+	ret = phydev->drv->get_plca_status(phydev, plca_st);
+
+	if (ret)
+		goto out_drv;
+
+out_drv:
+	mutex_unlock(&phydev->lock);
+out:
+	return ret;
+}
+
 /**
  * phy_start_cable_test - Start a cable test
  *
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 8e48b3cec5e7..44bd06be9691 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -3276,6 +3276,9 @@ static const struct ethtool_phy_ops phy_ethtool_phy_ops = {
 	.get_sset_count		= phy_ethtool_get_sset_count,
 	.get_strings		= phy_ethtool_get_strings,
 	.get_stats		= phy_ethtool_get_stats,
+	.get_plca_cfg		= phy_ethtool_get_plca_cfg,
+	.set_plca_cfg		= phy_ethtool_set_plca_cfg,
+	.get_plca_status	= phy_ethtool_get_plca_status,
 	.start_cable_test	= phy_start_cable_test,
 	.start_cable_test_tdr	= phy_start_cable_test_tdr,
 };
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 2a5c2d3a5da5..e0dcd534fe6f 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1845,6 +1845,13 @@ int phy_ethtool_get_strings(struct phy_device *phydev, u8 *data);
 int phy_ethtool_get_sset_count(struct phy_device *phydev);
 int phy_ethtool_get_stats(struct phy_device *phydev,
 			  struct ethtool_stats *stats, u64 *data);
+int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
+			     struct phy_plca_cfg *plca_cfg);
+int phy_ethtool_set_plca_cfg(struct phy_device *phydev,
+			     const struct phy_plca_cfg *plca_cfg,
+			     struct netlink_ext_ack *extack);
+int phy_ethtool_get_plca_status(struct phy_device *phydev,
+				struct phy_plca_status *plca_st);
 
 static inline int phy_package_read(struct phy_device *phydev, u32 regnum)
 {
-- 
2.37.4


^ permalink raw reply related	[flat|nested] 13+ messages in thread
* [PATCH v6 net-next 4/5] drivers/net/phy: add helpers to get/set PLCA configuration
  2022-12-10 22:45 [PATCH v6 net-next 0/5] add PLCA RS support and onsemi NCN26000 Piergiorgio Beruto
                   ` (2 preceding siblings ...)
  2022-12-10 22:46 ` [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA Piergiorgio Beruto
@ 2022-12-10 22:46 ` Piergiorgio Beruto
  2022-12-10 22:47 ` [PATCH v6 net-next 5/5] drivers/net/phy: add driver for the onsemi NCN26000 10BASE-T1S PHY Piergiorgio Beruto
  4 siblings, 0 replies; 13+ messages in thread
From: Piergiorgio Beruto @ 2022-12-10 22:46 UTC (permalink / raw)
  To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
	Eric Dumazet, Jakub Kicinski, Paolo Abeni
  Cc: linux-kernel, netdev, Oleksij Rempel

This patch adds support in phylib to read/write PLCA configuration for
Ethernet PHYs that support the OPEN Alliance "10BASE-T1S PLCA
Management Registers" specifications. These can be found at
https://www.opensig.org/about/specifications/

Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
---
 MAINTAINERS                          |   1 +
 drivers/net/phy/mdio-open-alliance.h |  47 +++++++
 drivers/net/phy/phy-c45.c            | 183 +++++++++++++++++++++++++++
 include/linux/phy.h                  |   6 +
 4 files changed, 237 insertions(+)
 create mode 100644 drivers/net/phy/mdio-open-alliance.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 7952243e4b43..ed626cbdf5af 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -16400,6 +16400,7 @@ PLCA RECONCILIATION SUBLAYER (IEEE802.3 Clause 148)
 M:	Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
+F:	drivers/net/phy/mdio-open-alliance.h
 F:	net/ethtool/plca.c
 
 PLDMFW LIBRARY
diff --git a/drivers/net/phy/mdio-open-alliance.h b/drivers/net/phy/mdio-open-alliance.h
new file mode 100644
index 000000000000..5f64514108b1
--- /dev/null
+++ b/drivers/net/phy/mdio-open-alliance.h
@@ -0,0 +1,47 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * mdio-open-alliance.h - definition of OPEN Alliance SIG standard registers
+ */
+
+#ifndef __MDIO_OPEN_ALLIANCE__
+#define __MDIO_OPEN_ALLIANCE__
+
+#include <linux/mdio.h>
+
+/* NOTE: all OATC14 registers are located in MDIO_MMD_VEND2 */
+
+/* Open Alliance TC14 (10BASE-T1S) registers */
+#define MDIO_OATC14_PLCA_IDVER	0xca00  /* PLCA ID and version */
+#define MDIO_OATC14_PLCA_CTRL0	0xca01	/* PLCA Control register 0 */
+#define MDIO_OATC14_PLCA_CTRL1	0xca02	/* PLCA Control register 1 */
+#define MDIO_OATC14_PLCA_STATUS	0xca03	/* PLCA Status register */
+#define MDIO_OATC14_PLCA_TOTMR	0xca04	/* PLCA TO Timer register */
+#define MDIO_OATC14_PLCA_BURST	0xca05	/* PLCA BURST mode register */
+
+/* Open Alliance TC14 PLCA IDVER register */
+#define MDIO_OATC14_PLCA_IDM	0xff00	/* PLCA MAP ID */
+#define MDIO_OATC14_PLCA_VER	0x00ff	/* PLCA MAP version */
+
+/* Open Alliance TC14 PLCA CTRL0 register */
+#define MDIO_OATC14_PLCA_EN	BIT(15) /* PLCA enable */
+#define MDIO_OATC14_PLCA_RST	BIT(14) /* PLCA reset */
+
+/* Open Alliance TC14 PLCA CTRL1 register */
+#define MDIO_OATC14_PLCA_NCNT	0xff00	/* PLCA node count */
+#define MDIO_OATC14_PLCA_ID	0x00ff	/* PLCA local node ID */
+
+/* Open Alliance TC14 PLCA STATUS register */
+#define MDIO_OATC14_PLCA_PST	BIT(15)	/* PLCA status indication */
+
+/* Open Alliance TC14 PLCA TOTMR register */
+#define MDIO_OATC14_PLCA_TOT	0x00ff
+
+/* Open Alliance TC14 PLCA BURST register */
+#define MDIO_OATC14_PLCA_MAXBC	0xff00
+#define MDIO_OATC14_PLCA_BTMR	0x00ff
+
+/* Version Identifiers */
+#define OATC14_IDM		0x0a00
+
+
+#endif /* __MDIO_OPEN_ALLIANCE__ */
diff --git a/drivers/net/phy/phy-c45.c b/drivers/net/phy/phy-c45.c
index a87a4b3ffce4..1a00d7e07817 100644
--- a/drivers/net/phy/phy-c45.c
+++ b/drivers/net/phy/phy-c45.c
@@ -8,6 +8,8 @@
 #include <linux/mii.h>
 #include <linux/phy.h>
 
+#include "mdio-open-alliance.h"
+
 /**
  * genphy_c45_baset1_able - checks if the PMA has BASE-T1 extended abilities
  * @phydev: target phy_device struct
@@ -931,6 +933,187 @@ int genphy_c45_fast_retrain(struct phy_device *phydev, bool enable)
 }
 EXPORT_SYMBOL_GPL(genphy_c45_fast_retrain);
 
+/**
+ * genphy_c45_plca_get_cfg - get PLCA configuration from standard registers
+ * @phydev: target phy_device struct
+ * @plca_cfg: output structure to store the PLCA configuration
+ *
+ * Description: if the PHY complies to the Open Alliance TC14 10BASE-T1S PLCA
+ *   Management Registers specifications, this function can be used to retrieve
+ *   the current PLCA configuration from the standard registers in MMD 31.
+ */
+int genphy_c45_plca_get_cfg(struct phy_device *phydev,
+			    struct phy_plca_cfg *plca_cfg)
+{
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, MDIO_OATC14_PLCA_IDVER);
+	if (ret < 0)
+		return ret;
+
+	if ((ret & MDIO_OATC14_PLCA_IDM) != OATC14_IDM)
+		return -ENODEV;
+
+	plca_cfg->version = ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, MDIO_OATC14_PLCA_CTRL0);
+	if (ret < 0)
+		return ret;
+
+	plca_cfg->enabled = !!(ret & MDIO_OATC14_PLCA_EN);
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, MDIO_OATC14_PLCA_CTRL1);
+	if (ret < 0)
+		return ret;
+
+	plca_cfg->node_cnt = (ret & MDIO_OATC14_PLCA_NCNT) >> 8;
+	plca_cfg->node_id = (ret & MDIO_OATC14_PLCA_ID);
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, MDIO_OATC14_PLCA_TOTMR);
+	if (ret < 0)
+		return ret;
+
+	plca_cfg->to_tmr = ret & MDIO_OATC14_PLCA_TOT;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, MDIO_OATC14_PLCA_BURST);
+	if (ret < 0)
+		return ret;
+
+	plca_cfg->burst_cnt = (ret & MDIO_OATC14_PLCA_MAXBC) >> 8;
+	plca_cfg->burst_tmr = (ret & MDIO_OATC14_PLCA_BTMR);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(genphy_c45_plca_get_cfg);
+
+/**
+ * genphy_c45_plca_set_cfg - set PLCA configuration using standard registers
+ * @phydev: target phy_device struct
+ * @plca_cfg: structure containing the PLCA configuration. Fields set to -1 are
+ * not to be changed.
+ *
+ * Description: if the PHY complies to the Open Alliance TC14 10BASE-T1S PLCA
+ *   Management Registers specifications, this function can be used to modify
+ *   the PLCA configuration using the standard registers in MMD 31.
+ */
+int genphy_c45_plca_set_cfg(struct phy_device *phydev,
+			    const struct phy_plca_cfg *plca_cfg)
+{
+	int ret;
+	u16 val;
+
+	// PLCA IDVER is read-only
+	if (plca_cfg->version >= 0)
+		return -EINVAL;
+
+	// first of all, disable PLCA if required
+	if (plca_cfg->enabled == 0) {
+		ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2,
+					 MDIO_OATC14_PLCA_CTRL0,
+					 MDIO_OATC14_PLCA_EN);
+
+		if (ret < 0)
+			return ret;
+	}
+
+	if (plca_cfg->node_cnt >= 0 || plca_cfg->node_id >= 0) {
+		if (plca_cfg->node_cnt < 0 || plca_cfg->node_id < 0) {
+			ret = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+					   MDIO_OATC14_PLCA_CTRL1);
+
+			if (ret < 0)
+				return ret;
+
+			val = ret;
+		}
+
+		if (plca_cfg->node_cnt >= 0)
+			val = (val & ~MDIO_OATC14_PLCA_NCNT) |
+			      (plca_cfg->node_cnt << 8);
+
+		if (plca_cfg->node_id >= 0)
+			val = (val & ~MDIO_OATC14_PLCA_ID) |
+			      (plca_cfg->node_id);
+
+		ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
+				    MDIO_OATC14_PLCA_CTRL1, val);
+
+		if (ret < 0)
+			return ret;
+	}
+
+	if (plca_cfg->to_tmr >= 0) {
+		ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
+				    MDIO_OATC14_PLCA_TOTMR,
+				    plca_cfg->to_tmr);
+
+		if (ret < 0)
+			return ret;
+	}
+
+	if (plca_cfg->burst_cnt >= 0 || plca_cfg->burst_tmr >= 0) {
+		if (plca_cfg->burst_cnt < 0 || plca_cfg->burst_tmr < 0) {
+			ret = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+					   MDIO_OATC14_PLCA_BURST);
+
+			if (ret < 0)
+				return ret;
+
+			val = ret;
+		}
+
+		if (plca_cfg->burst_cnt >= 0)
+			val = (val & ~MDIO_OATC14_PLCA_MAXBC) |
+			      (plca_cfg->burst_cnt << 8);
+
+		if (plca_cfg->burst_tmr >= 0)
+			val = (val & ~MDIO_OATC14_PLCA_BTMR) |
+			      (plca_cfg->burst_tmr);
+
+		ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
+				    MDIO_OATC14_PLCA_BURST, val);
+
+		if (ret < 0)
+			return ret;
+	}
+
+	// if we need to enable PLCA, do it at the end
+	if (plca_cfg->enabled > 0) {
+		ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2,
+				       MDIO_OATC14_PLCA_CTRL0,
+				       MDIO_OATC14_PLCA_EN);
+
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(genphy_c45_plca_set_cfg);
+
+/**
+ * genphy_c45_plca_get_status - get PLCA status from standard registers
+ * @phydev: target phy_device struct
+ * @plca_st: output structure to store the PLCA status
+ *
+ * Description: if the PHY complies to the Open Alliance TC14 10BASE-T1S PLCA
+ *   Management Registers specifications, this function can be used to retrieve
+ *   the current PLCA status information from the standard registers in MMD 31.
+ */
+int genphy_c45_plca_get_status(struct phy_device *phydev,
+			       struct phy_plca_status *plca_st)
+{
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, MDIO_OATC14_PLCA_STATUS);
+	if (ret < 0)
+		return ret;
+
+	plca_st->pst = !!(ret & MDIO_OATC14_PLCA_PST);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(genphy_c45_plca_get_status);
+
 struct phy_driver genphy_c45_driver = {
 	.phy_id         = 0xffffffff,
 	.phy_id_mask    = 0xffffffff,
diff --git a/include/linux/phy.h b/include/linux/phy.h
index e0dcd534fe6f..458924847ebc 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1747,6 +1747,12 @@ int genphy_c45_loopback(struct phy_device *phydev, bool enable);
 int genphy_c45_pma_resume(struct phy_device *phydev);
 int genphy_c45_pma_suspend(struct phy_device *phydev);
 int genphy_c45_fast_retrain(struct phy_device *phydev, bool enable);
+int genphy_c45_plca_get_cfg(struct phy_device *phydev,
+			    struct phy_plca_cfg *plca_cfg);
+int genphy_c45_plca_set_cfg(struct phy_device *phydev,
+			    const struct phy_plca_cfg *plca_cfg);
+int genphy_c45_plca_get_status(struct phy_device *phydev,
+			       struct phy_plca_status *plca_st);
 
 /* Generic C45 PHY driver */
 extern struct phy_driver genphy_c45_driver;
-- 
2.37.4


^ permalink raw reply related	[flat|nested] 13+ messages in thread
* [PATCH v6 net-next 5/5] drivers/net/phy: add driver for the onsemi NCN26000 10BASE-T1S PHY
  2022-12-10 22:45 [PATCH v6 net-next 0/5] add PLCA RS support and onsemi NCN26000 Piergiorgio Beruto
                   ` (3 preceding siblings ...)
  2022-12-10 22:46 ` [PATCH v6 net-next 4/5] drivers/net/phy: add helpers to get/set PLCA configuration Piergiorgio Beruto
@ 2022-12-10 22:47 ` Piergiorgio Beruto
  4 siblings, 0 replies; 13+ messages in thread
From: Piergiorgio Beruto @ 2022-12-10 22:47 UTC (permalink / raw)
  To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
	Eric Dumazet, Jakub Kicinski, Paolo Abeni
  Cc: linux-kernel, netdev, Oleksij Rempel

This patch adds support for the onsemi NCN26000 10BASE-T1S industrial
Ethernet PHY. The driver supports Point-to-Multipoint operation without
auto-negotiation and with link control handling. The PHY also features
PLCA for improving performance in P2MP mode.

Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
---
 MAINTAINERS                |   7 ++
 drivers/net/phy/Kconfig    |   7 ++
 drivers/net/phy/Makefile   |   1 +
 drivers/net/phy/ncn26000.c | 171 +++++++++++++++++++++++++++++++++++++
 4 files changed, 186 insertions(+)
 create mode 100644 drivers/net/phy/ncn26000.c

diff --git a/MAINTAINERS b/MAINTAINERS
index ed626cbdf5af..09f0bfa3ae64 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15357,6 +15357,13 @@ L:	linux-mips@vger.kernel.org
 S:	Maintained
 F:	arch/mips/boot/dts/ralink/omega2p.dts
 
+ONSEMI ETHERNET PHY DRIVERS
+M:	Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
+L:	netdev@vger.kernel.org
+S:	Supported
+W:	http://www.onsemi.com
+F:	drivers/net/phy/ncn*
+
 OP-TEE DRIVER
 M:	Jens Wiklander <jens.wiklander@linaro.org>
 L:	op-tee@lists.trustedfirmware.org
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 1327290decab..08706efa4b43 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -264,6 +264,13 @@ config NATIONAL_PHY
 	help
 	  Currently supports the DP83865 PHY.
 
+config NCN26000_PHY
+	tristate "onsemi 10BASE-T1S Ethernet PHY"
+	help
+	  Adds support for the onsemi 10BASE-T1S Ethernet PHY.
+	  Currently supports the NCN26000 10BASE-T1S Industrial PHY
+	  with MII interface.
+
 config NXP_C45_TJA11XX_PHY
 	tristate "NXP C45 TJA11XX PHYs"
 	depends on PTP_1588_CLOCK_OPTIONAL
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index f7138d3c896b..b5138066ba04 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -77,6 +77,7 @@ obj-$(CONFIG_MICROCHIP_T1_PHY)	+= microchip_t1.o
 obj-$(CONFIG_MICROSEMI_PHY)	+= mscc/
 obj-$(CONFIG_MOTORCOMM_PHY)	+= motorcomm.o
 obj-$(CONFIG_NATIONAL_PHY)	+= national.o
+obj-$(CONFIG_NCN26000_PHY)	+= ncn26000.o
 obj-$(CONFIG_NXP_C45_TJA11XX_PHY)	+= nxp-c45-tja11xx.o
 obj-$(CONFIG_NXP_TJA11XX_PHY)	+= nxp-tja11xx.o
 obj-$(CONFIG_QSEMI_PHY)		+= qsemi.o
diff --git a/drivers/net/phy/ncn26000.c b/drivers/net/phy/ncn26000.c
new file mode 100644
index 000000000000..78712d0e2b7e
--- /dev/null
+++ b/drivers/net/phy/ncn26000.c
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ *  Driver for the onsemi 10BASE-T1S NCN26000 PHYs family.
+ *
+ * Copyright 2022 onsemi
+ */
+#include <linux/kernel.h>
+#include <linux/bitfield.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+
+#include "mdio-open-alliance.h"
+
+#define PHY_ID_NCN26000			0x180FF5A1
+
+#define NCN26000_REG_IRQ_CTL            16
+#define NCN26000_REG_IRQ_STATUS         17
+
+// the NCN26000 maps link_ctrl to BMCR_ANENABLE
+#define NCN26000_BCMR_LINK_CTRL_BIT	BMCR_ANENABLE
+
+// the NCN26000 maps link_status to BMSR_ANEGCOMPLETE
+#define NCN26000_BMSR_LINK_STATUS_BIT	BMSR_ANEGCOMPLETE
+
+#define NCN26000_IRQ_LINKST_BIT		BIT(0)
+#define NCN26000_IRQ_PLCAST_BIT		BIT(1)
+#define NCN26000_IRQ_LJABBER_BIT	BIT(2)
+#define NCN26000_IRQ_RJABBER_BIT	BIT(3)
+#define NCN26000_IRQ_PLCAREC_BIT	BIT(4)
+#define NCN26000_IRQ_PHYSCOL_BIT	BIT(5)
+#define NCN26000_IRQ_RESET_BIT		BIT(15)
+
+#define TO_TMR_DEFAULT			32
+
+// driver callbacks --------------------------------------------------------- //
+
+static int ncn26000_config_init(struct phy_device *phydev)
+{
+	/* HW bug workaround: the default value of the PLCA TO_TIMER should be
+	 * 32, where the current version of NCN26000 reports 24. This will be
+	 * fixed in future PHY versions. For the time being, we force the
+	 * correct default here.
+	 */
+	return phy_write_mmd(phydev, MDIO_MMD_VEND2, MDIO_OATC14_PLCA_TOTMR,
+			     TO_TMR_DEFAULT);
+}
+
+static int ncn26000_config_aneg(struct phy_device *phydev)
+{
+	// Note: the NCN26000 supports only P2MP link mode. Therefore, AN is not
+	// supported. However, this function is invoked by phylib to enable the
+	// PHY, regardless of the AN support.
+	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+	phydev->mdix = ETH_TP_MDI;
+
+	// bring up the link
+	return phy_write(phydev, MII_BMCR, NCN26000_BCMR_LINK_CTRL_BIT);
+}
+
+static int ncn26000_read_status(struct phy_device *phydev)
+{
+	// The NCN26000 reports NCN26000_LINK_STATUS_BIT if the link status of
+	// the PHY is up. It further reports the logical AND of the link status
+	// and the PLCA status in the BMSR_LSTATUS bit.
+	int ret;
+
+	/* The link state is latched low so that momentary link
+	 * drops can be detected. Do not double-read the status
+	 * in polling mode to detect such short link drops except
+	 * the link was already down.
+	 */
+	if (!phy_polling_mode(phydev) || !phydev->link) {
+		ret = phy_read(phydev, MII_BMSR);
+		if (ret < 0)
+			return ret;
+		else if (ret & NCN26000_BMSR_LINK_STATUS_BIT)
+			goto upd_link;
+	}
+
+	ret = phy_read(phydev, MII_BMSR);
+	if (unlikely(ret < 0))
+		return ret;
+
+upd_link:
+	// update link status
+	if (ret & NCN26000_BMSR_LINK_STATUS_BIT) {
+		phydev->link = 1;
+		phydev->pause = 0;
+		phydev->duplex = DUPLEX_HALF;
+		phydev->speed = SPEED_10;
+	} else {
+		phydev->link = 0;
+		phydev->duplex = DUPLEX_UNKNOWN;
+		phydev->speed = SPEED_UNKNOWN;
+	}
+
+	return 0;
+}
+
+static irqreturn_t ncn26000_handle_interrupt(struct phy_device *phydev)
+{
+	int ret;
+
+	// read and aknowledge the IRQ status register
+	ret = phy_read(phydev, NCN26000_REG_IRQ_STATUS);
+
+	// check only link status changes
+	if (unlikely(ret < 0) || (ret & NCN26000_REG_IRQ_STATUS) == 0)
+		return IRQ_NONE;
+
+	phy_trigger_machine(phydev);
+	return IRQ_HANDLED;
+}
+
+static int ncn26000_config_intr(struct phy_device *phydev)
+{
+	int ret;
+	u16 irqe;
+
+	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
+		// acknowledge IRQs
+		ret = phy_read(phydev, NCN26000_REG_IRQ_STATUS);
+		if (ret < 0)
+			return ret;
+
+		// get link status notifications
+		irqe = NCN26000_IRQ_LINKST_BIT;
+	} else {
+		// disable all IRQs
+		irqe = 0;
+	}
+
+	ret = phy_write(phydev, NCN26000_REG_IRQ_CTL, irqe);
+	if (ret != 0)
+		return ret;
+
+	return 0;
+}
+
+static struct phy_driver ncn26000_driver[] = {
+	{
+		PHY_ID_MATCH_MODEL(PHY_ID_NCN26000),
+		.name			= "NCN26000",
+		.features		= PHY_BASIC_T1S_P2MP_FEATURES,
+		.config_init            = ncn26000_config_init,
+		.config_intr            = ncn26000_config_intr,
+		.config_aneg		= ncn26000_config_aneg,
+		.read_status		= ncn26000_read_status,
+		.handle_interrupt       = ncn26000_handle_interrupt,
+		.get_plca_cfg		= genphy_c45_plca_get_cfg,
+		.set_plca_cfg		= genphy_c45_plca_set_cfg,
+		.get_plca_status	= genphy_c45_plca_get_status,
+		.soft_reset             = genphy_soft_reset,
+	},
+};
+
+module_phy_driver(ncn26000_driver);
+
+static struct mdio_device_id __maybe_unused ncn26000_tbl[] = {
+	{ PHY_ID_MATCH_MODEL(PHY_ID_NCN26000) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, ncn26000_tbl);
+
+MODULE_AUTHOR("Piergiorgio Beruto");
+MODULE_DESCRIPTION("onsemi 10BASE-T1S PHY driver");
+MODULE_LICENSE("Dual BSD/GPL");
-- 
2.37.4


^ permalink raw reply related	[flat|nested] 13+ messages in thread
* Re: [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA
  2022-12-10 22:46 ` [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA Piergiorgio Beruto
@ 2022-12-11 12:05   ` kernel test robot
  2022-12-11 12:23   ` Russell King (Oracle)
  1 sibling, 0 replies; 13+ messages in thread
From: kernel test robot @ 2022-12-11 12:05 UTC (permalink / raw)
  To: Piergiorgio Beruto, Andrew Lunn, Heiner Kallweit, Russell King,
	David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni
  Cc: oe-kbuild-all, netdev, linux-kernel, Oleksij Rempel

[-- Attachment #1: Type: text/plain, Size: 5199 bytes --]

Hi Piergiorgio,

I love your patch! Perhaps something to improve:

[auto build test WARNING on net-next/master]

url:    https://github.com/intel-lab-lkp/linux/commits/Piergiorgio-Beruto/add-PLCA-RS-support-and-onsemi-NCN26000/20221211-064827
patch link:    https://lore.kernel.org/r/75cb0eab15e62fc350e86ba9e5b0af72ea45b484.1670712151.git.piergiorgio.beruto%40gmail.com
patch subject: [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA
config: m68k-randconfig-s043-20221211
compiler: m68k-linux-gcc (GCC) 12.1.0
reproduce:
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # apt-get install sparse
        # sparse version: v0.6.4-39-gce1a6720-dirty
        # https://github.com/intel-lab-lkp/linux/commit/333e7a2a5e52756e9320c13b6fbe1f5e9aef65d4
        git remote add linux-review https://github.com/intel-lab-lkp/linux
        git fetch --no-tags linux-review Piergiorgio-Beruto/add-PLCA-RS-support-and-onsemi-NCN26000/20221211-064827
        git checkout 333e7a2a5e52756e9320c13b6fbe1f5e9aef65d4
        # save the config file
        mkdir build_dir && cp config build_dir/.config
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__' O=build_dir ARCH=m68k SHELL=/bin/bash drivers/net/phy/

If you fix the issue, kindly add following tag where applicable
| Reported-by: kernel test robot <lkp@intel.com>

sparse warnings: (new ones prefixed by >>)
>> drivers/net/phy/phy.c:593:46: sparse: sparse: Using plain integer as NULL pointer

vim +593 drivers/net/phy/phy.c

   580	
   581	/**
   582	 * phy_ethtool_set_plca_cfg - Set PLCA RS configuration
   583	 *
   584	 * @phydev: the phy_device struct
   585	 * @extack: extack for reporting useful error messages
   586	 * @plca_cfg: new PLCA configuration to apply
   587	 */
   588	int phy_ethtool_set_plca_cfg(struct phy_device *phydev,
   589				     const struct phy_plca_cfg *plca_cfg,
   590				     struct netlink_ext_ack *extack)
   591	{
   592		int ret;
 > 593		struct phy_plca_cfg *curr_plca_cfg = 0;
   594	
   595		if (!phydev->drv) {
   596			ret = -EIO;
   597			goto out;
   598		}
   599	
   600		if (!phydev->drv->set_plca_cfg ||
   601		    !phydev->drv->get_plca_cfg) {
   602			ret = -EOPNOTSUPP;
   603			goto out;
   604		}
   605	
   606		curr_plca_cfg = kmalloc(sizeof(*curr_plca_cfg), GFP_KERNEL);
   607		memset(curr_plca_cfg, 0xFF, sizeof(*curr_plca_cfg));
   608	
   609		mutex_lock(&phydev->lock);
   610	
   611		ret = phydev->drv->get_plca_cfg(phydev, curr_plca_cfg);
   612		if (ret)
   613			goto out_drv;
   614	
   615		if (curr_plca_cfg->enabled < 0 && plca_cfg->enabled >= 0) {
   616			NL_SET_ERR_MSG(extack,
   617				       "PHY does not support changing the PLCA 'enable' attribute");
   618			ret = -EINVAL;
   619			goto out_drv;
   620		}
   621	
   622		if (curr_plca_cfg->node_id < 0 && plca_cfg->node_id >= 0) {
   623			NL_SET_ERR_MSG(extack,
   624				       "PHY does not support changing the PLCA 'local node ID' attribute");
   625			ret = -EINVAL;
   626			goto out_drv;
   627		}
   628	
   629		if (curr_plca_cfg->node_cnt < 0 && plca_cfg->node_cnt >= 0) {
   630			NL_SET_ERR_MSG(extack,
   631				       "PHY does not support changing the PLCA 'node count' attribute");
   632			ret = -EINVAL;
   633			goto out_drv;
   634		}
   635	
   636		if (curr_plca_cfg->to_tmr < 0 && plca_cfg->to_tmr >= 0) {
   637			NL_SET_ERR_MSG(extack,
   638				       "PHY does not support changing the PLCA 'TO timer' attribute");
   639			ret = -EINVAL;
   640			goto out_drv;
   641		}
   642	
   643		if (curr_plca_cfg->burst_cnt < 0 && plca_cfg->burst_cnt >= 0) {
   644			NL_SET_ERR_MSG(extack,
   645				       "PHY does not support changing the PLCA 'burst count' attribute");
   646			ret = -EINVAL;
   647			goto out_drv;
   648		}
   649	
   650		if (curr_plca_cfg->burst_tmr < 0 && plca_cfg->burst_tmr >= 0) {
   651			NL_SET_ERR_MSG(extack,
   652				       "PHY does not support changing the PLCA 'burst timer' attribute");
   653			ret = -EINVAL;
   654			goto out_drv;
   655		}
   656	
   657		// if enabling PLCA, perform additional sanity checks
   658		if (plca_cfg->enabled > 0) {
   659			if (!linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT,
   660					       phydev->advertising)) {
   661				ret = -EOPNOTSUPP;
   662				NL_SET_ERR_MSG(extack,
   663					       "Point to Multi-Point mode is not enabled");
   664			}
   665	
   666			// allow setting node_id concurrently with enabled
   667			if (plca_cfg->node_id >= 0)
   668				curr_plca_cfg->node_id = plca_cfg->node_id;
   669	
   670			if (curr_plca_cfg->node_id >= 255) {
   671				NL_SET_ERR_MSG(extack, "PLCA node ID is not set");
   672				ret = -EINVAL;
   673				goto out_drv;
   674			}
   675		}
   676	
   677		ret = phydev->drv->set_plca_cfg(phydev, plca_cfg);
   678		if (ret)
   679			goto out_drv;
   680	
   681	out_drv:
   682		kfree(curr_plca_cfg);
   683		mutex_unlock(&phydev->lock);
   684	out:
   685		return ret;
   686	}
   687	

-- 
0-DAY CI Kernel Test Service
https://01.org/lkp

[-- Attachment #2: config --]
[-- Type: text/plain, Size: 162367 bytes --]

#
# Automatically generated file; DO NOT EDIT.
# Linux/m68k 6.1.0-rc8 Kernel Configuration
#
CONFIG_CC_VERSION_TEXT="m68k-linux-gcc (GCC) 12.1.0"
CONFIG_CC_IS_GCC=y
CONFIG_GCC_VERSION=120100
CONFIG_CLANG_VERSION=0
CONFIG_AS_IS_GNU=y
CONFIG_AS_VERSION=23800
CONFIG_LD_IS_BFD=y
CONFIG_LD_VERSION=23800
CONFIG_LLD_VERSION=0
CONFIG_CC_HAS_ASM_INLINE=y
CONFIG_CC_HAS_NO_PROFILE_FN_ATTR=y
CONFIG_PAHOLE_VERSION=123
CONFIG_IRQ_WORK=y

#
# General setup
#
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_COMPILE_TEST=y
# CONFIG_WERROR is not set
CONFIG_LOCALVERSION=""
CONFIG_BUILD_SALT=""
CONFIG_DEFAULT_INIT=""
CONFIG_DEFAULT_HOSTNAME="(none)"
# CONFIG_SYSVIPC is not set
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_WATCH_QUEUE is not set
# CONFIG_USELIB is not set
CONFIG_AUDIT=y

#
# IRQ subsystem
#
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_IRQ_CHIP=y
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_SIM=y
CONFIG_IRQ_DOMAIN_HIERARCHY=y
CONFIG_IRQ_FASTEOI_HIERARCHY_HANDLERS=y
# CONFIG_GENERIC_IRQ_DEBUGFS is not set
# end of IRQ subsystem

CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_CONTEXT_TRACKING=y
CONFIG_CONTEXT_TRACKING_IDLE=y

#
# Timers subsystem
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ_COMMON=y
# CONFIG_HZ_PERIODIC is not set
CONFIG_NO_HZ_IDLE=y
# CONFIG_NO_HZ is not set
CONFIG_HIGH_RES_TIMERS=y
# end of Timers subsystem

CONFIG_BPF=y

#
# BPF subsystem
#
# CONFIG_BPF_SYSCALL is not set
# end of BPF subsystem

CONFIG_PREEMPT_BUILD=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_COUNT=y
CONFIG_PREEMPTION=y

#
# CPU/Task time and stats accounting
#
CONFIG_TICK_CPU_ACCOUNTING=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_PSI is not set
# end of CPU/Task time and stats accounting

CONFIG_CPU_ISOLATION=y

#
# RCU Subsystem
#
CONFIG_TREE_RCU=y
CONFIG_PREEMPT_RCU=y
CONFIG_RCU_EXPERT=y
CONFIG_SRCU=y
CONFIG_TREE_SRCU=y
# CONFIG_FORCE_TASKS_RCU is not set
# CONFIG_FORCE_TASKS_RUDE_RCU is not set
# CONFIG_FORCE_TASKS_TRACE_RCU is not set
CONFIG_RCU_STALL_COMMON=y
CONFIG_RCU_NEED_SEGCBLIST=y
CONFIG_RCU_FANOUT=32
CONFIG_RCU_FANOUT_LEAF=16
# CONFIG_RCU_BOOST is not set
CONFIG_RCU_NOCB_CPU=y
# CONFIG_RCU_NOCB_CPU_DEFAULT_ALL is not set
# end of RCU Subsystem

CONFIG_BUILD_BIN2C=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_IKHEADERS=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_PRINTK_SAFE_LOG_BUF_SHIFT=13
# CONFIG_PRINTK_INDEX is not set

#
# Scheduler features
#
# end of Scheduler features

CONFIG_CC_IMPLICIT_FALLTHROUGH="-Wimplicit-fallthrough=5"
CONFIG_GCC12_NO_ARRAY_BOUNDS=y
CONFIG_CC_NO_ARRAY_BOUNDS=y
CONFIG_CGROUPS=y
CONFIG_PAGE_COUNTER=y
# CONFIG_CGROUP_FAVOR_DYNMODS is not set
CONFIG_MEMCG=y
CONFIG_MEMCG_KMEM=y
# CONFIG_BLK_CGROUP is not set
CONFIG_CGROUP_SCHED=y
CONFIG_FAIR_GROUP_SCHED=y
# CONFIG_CFS_BANDWIDTH is not set
# CONFIG_RT_GROUP_SCHED is not set
CONFIG_CGROUP_PIDS=y
CONFIG_CGROUP_RDMA=y
# CONFIG_CGROUP_FREEZER is not set
# CONFIG_CGROUP_DEVICE is not set
# CONFIG_CGROUP_CPUACCT is not set
CONFIG_CGROUP_MISC=y
CONFIG_NAMESPACES=y
# CONFIG_UTS_NS is not set
CONFIG_IPC_NS=y
# CONFIG_USER_NS is not set
CONFIG_PID_NS=y
CONFIG_NET_NS=y
# CONFIG_CHECKPOINT_RESTORE is not set
CONFIG_SCHED_AUTOGROUP=y
# CONFIG_SYSFS_DEPRECATED is not set
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_RD_GZIP is not set
# CONFIG_RD_BZIP2 is not set
CONFIG_RD_LZMA=y
CONFIG_RD_XZ=y
CONFIG_RD_LZO=y
# CONFIG_RD_LZ4 is not set
CONFIG_RD_ZSTD=y
# CONFIG_BOOT_CONFIG is not set
CONFIG_INITRAMFS_PRESERVE_MTIME=y
# CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_HAVE_UID16=y
# CONFIG_EXPERT is not set
CONFIG_UID16=y
CONFIG_MULTIUSER=y
CONFIG_SGETMASK_SYSCALL=y
CONFIG_SYSFS_SYSCALL=y
CONFIG_FHANDLE=y
CONFIG_POSIX_TIMERS=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_FUTEX_PI=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_AIO=y
CONFIG_IO_URING=y
CONFIG_ADVISE_SYSCALLS=y
CONFIG_MEMBARRIER=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_BASE_RELATIVE=y
CONFIG_KCMP=y
# CONFIG_EMBEDDED is not set

#
# Kernel Performance Events And Counters
#
# end of Kernel Performance Events And Counters

CONFIG_SYSTEM_DATA_VERIFICATION=y
CONFIG_PROFILING=y
# end of General setup

CONFIG_M68K=y
CONFIG_CPU_BIG_ENDIAN=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_CSUM=y
CONFIG_TIME_LOW_RES=y
CONFIG_NO_IOPORT_MAP=y
CONFIG_HZ=100
CONFIG_PGTABLE_LEVELS=2
# CONFIG_MMU is not set

#
# Platform setup
#

#
# Processor Type
#
# CONFIG_M68KCLASSIC is not set
CONFIG_COLDFIRE=y
# CONFIG_M5206 is not set
# CONFIG_M5206e is not set
# CONFIG_M520x is not set
CONFIG_M523x=y
# CONFIG_M5249 is not set
# CONFIG_M525x is not set
# CONFIG_M5271 is not set
# CONFIG_M5272 is not set
# CONFIG_M5275 is not set
# CONFIG_M528x is not set
# CONFIG_M5307 is not set
# CONFIG_M532x is not set
# CONFIG_M537x is not set
# CONFIG_M5407 is not set
# CONFIG_M547x is not set
# CONFIG_M548x is not set
# CONFIG_M5441x is not set
CONFIG_COLDFIRE_PIT_TIMER=y

#
# Processor Specific Options
#
CONFIG_ARCH_FORCE_MAX_ORDER=11
CONFIG_CPU_HAS_NO_BITFIELDS=y
CONFIG_CPU_HAS_NO_CAS=y
CONFIG_CPU_HAS_NO_MULDIV64=y
CONFIG_HAVE_CACHE_SPLIT=y
CONFIG_HAVE_IPSBAR=y
CONFIG_CLOCK_FREQ=150000000
CONFIG_CACHE_I=y
# CONFIG_CACHE_D is not set
# CONFIG_CACHE_BOTH is not set

#
# Machine Types
#
# CONFIG_M5235EVB is not set

#
# Machine Options
#
# CONFIG_UBOOT is not set
# CONFIG_4KSTACKS is not set

#
# RAM configuration
#
CONFIG_RAMBASE=0
CONFIG_RAMSIZE=0x400000
CONFIG_VECTORBASE=0
CONFIG_IPSBAR=0x40000000
CONFIG_KERNELBASE=0x400

#
# ROM configuration
#
# CONFIG_ROM is not set
CONFIG_RAMKERNEL=y
# end of Platform setup

#
# Kernel Features
#
# end of Kernel Features

#
# Power management options
#
# CONFIG_PM is not set
# end of Power management options

#
# General architecture-dependent options
#
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_ARCH_32BIT_OFF_T=y
CONFIG_HAVE_ASM_MODVERSIONS=y
CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
CONFIG_LTO_NONE=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_MODULES_USE_ELF_RELA=y
CONFIG_MODULES_USE_ELF_REL=y
CONFIG_PAGE_SIZE_LESS_THAN_64KB=y
CONFIG_PAGE_SIZE_LESS_THAN_256KB=y
CONFIG_OLD_SIGSUSPEND3=y
CONFIG_OLD_SIGACTION=y
CONFIG_COMPAT_32BIT_TIME=y
CONFIG_LOCK_EVENT_COUNTS=y

#
# GCOV-based kernel profiling
#
# CONFIG_GCOV_KERNEL is not set
# end of GCOV-based kernel profiling
# end of General architecture-dependent options

CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
# CONFIG_MODULES is not set
CONFIG_BLOCK=y
CONFIG_BLOCK_LEGACY_AUTOLOAD=y
CONFIG_BLK_DEV_BSG_COMMON=y
CONFIG_BLK_ICQ=y
CONFIG_BLK_DEV_BSGLIB=y
CONFIG_BLK_DEV_INTEGRITY=y
CONFIG_BLK_DEV_INTEGRITY_T10=y
CONFIG_BLK_DEV_ZONED=y
CONFIG_BLK_WBT=y
CONFIG_BLK_WBT_MQ=y
# CONFIG_BLK_DEBUG_FS is not set
# CONFIG_BLK_SED_OPAL is not set
# CONFIG_BLK_INLINE_ENCRYPTION is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
CONFIG_ACORN_PARTITION=y
CONFIG_ACORN_PARTITION_CUMANA=y
# CONFIG_ACORN_PARTITION_EESOX is not set
# CONFIG_ACORN_PARTITION_ICS is not set
CONFIG_ACORN_PARTITION_ADFS=y
# CONFIG_ACORN_PARTITION_POWERTEC is not set
CONFIG_ACORN_PARTITION_RISCIX=y
CONFIG_AIX_PARTITION=y
CONFIG_OSF_PARTITION=y
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
CONFIG_ULTRIX_PARTITION=y
# CONFIG_SUN_PARTITION is not set
CONFIG_KARMA_PARTITION=y
# CONFIG_EFI_PARTITION is not set
CONFIG_SYSV68_PARTITION=y
CONFIG_CMDLINE_PARTITION=y
# end of Partition Types

CONFIG_BLK_MQ_VIRTIO=y
CONFIG_BLOCK_HOLDER_DEPRECATED=y
CONFIG_BLK_MQ_STACKING=y

#
# IO Schedulers
#
CONFIG_MQ_IOSCHED_DEADLINE=y
# CONFIG_MQ_IOSCHED_KYBER is not set
CONFIG_IOSCHED_BFQ=y
# end of IO Schedulers

CONFIG_ASN1=y
CONFIG_UNINLINE_SPIN_UNLOCK=y

#
# Executable file formats
#
CONFIG_BINFMT_ELF_FDPIC=y
CONFIG_ELFCORE=y
# CONFIG_BINFMT_SCRIPT is not set
CONFIG_ARCH_HAS_BINFMT_FLAT=y
# CONFIG_BINFMT_FLAT is not set
CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y
CONFIG_BINFMT_MISC=y
CONFIG_COREDUMP=y
# end of Executable file formats

#
# Memory Management options
#

#
# SLAB allocator options
#
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLAB_MERGE_DEFAULT is not set
# CONFIG_SLAB_FREELIST_RANDOM is not set
CONFIG_SLAB_FREELIST_HARDENED=y
CONFIG_SLUB_STATS=y
# end of SLAB allocator options

# CONFIG_SHUFFLE_PAGE_ALLOCATOR is not set
# CONFIG_COMPAT_BRK is not set
CONFIG_FLATMEM=y
CONFIG_SPLIT_PTLOCK_CPUS=999999
CONFIG_MEMORY_BALLOON=y
CONFIG_PAGE_REPORTING=y
CONFIG_NOMMU_INITIAL_TRIM_EXCESS=1
CONFIG_NEED_PER_CPU_KM=y
CONFIG_ARCH_HAS_CURRENT_STACK_POINTER=y
CONFIG_ZONE_DMA=y
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_PERCPU_STATS is not set
CONFIG_GUP_TEST=y

#
# Data Access Monitoring
#
CONFIG_DAMON=y
# CONFIG_DAMON_SYSFS is not set
# end of Data Access Monitoring
# end of Memory Management options

CONFIG_NET=y

#
# Networking options
#
# CONFIG_PACKET is not set
# CONFIG_UNIX is not set
# CONFIG_INET is not set
# CONFIG_NETWORK_SECMARK is not set
CONFIG_NET_PTP_CLASSIFY=y
CONFIG_NETWORK_PHY_TIMESTAMPING=y
# CONFIG_NETFILTER is not set
# CONFIG_ATM is not set
CONFIG_STP=y
CONFIG_GARP=y
# CONFIG_BRIDGE is not set
CONFIG_VLAN_8021Q=y
CONFIG_VLAN_8021Q_GVRP=y
# CONFIG_VLAN_8021Q_MVRP is not set
CONFIG_LLC=y
CONFIG_LLC2=y
# CONFIG_ATALK is not set
CONFIG_X25=y
CONFIG_LAPB=y
CONFIG_PHONET=y
# CONFIG_IEEE802154 is not set
CONFIG_NET_SCHED=y

#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=y
# CONFIG_NET_SCH_HTB is not set
# CONFIG_NET_SCH_HFSC is not set
CONFIG_NET_SCH_PRIO=y
CONFIG_NET_SCH_MULTIQ=y
CONFIG_NET_SCH_RED=y
# CONFIG_NET_SCH_SFB is not set
# CONFIG_NET_SCH_SFQ is not set
# CONFIG_NET_SCH_TEQL is not set
CONFIG_NET_SCH_TBF=y
CONFIG_NET_SCH_CBS=y
CONFIG_NET_SCH_ETF=y
# CONFIG_NET_SCH_TAPRIO is not set
# CONFIG_NET_SCH_GRED is not set
CONFIG_NET_SCH_DSMARK=y
CONFIG_NET_SCH_NETEM=y
CONFIG_NET_SCH_DRR=y
CONFIG_NET_SCH_MQPRIO=y
CONFIG_NET_SCH_SKBPRIO=y
# CONFIG_NET_SCH_CHOKE is not set
# CONFIG_NET_SCH_QFQ is not set
CONFIG_NET_SCH_CODEL=y
CONFIG_NET_SCH_FQ_CODEL=y
# CONFIG_NET_SCH_CAKE is not set
CONFIG_NET_SCH_FQ=y
# CONFIG_NET_SCH_HHF is not set
CONFIG_NET_SCH_PIE=y
CONFIG_NET_SCH_FQ_PIE=y
# CONFIG_NET_SCH_PLUG is not set
CONFIG_NET_SCH_ETS=y
# CONFIG_NET_SCH_DEFAULT is not set

#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=y
CONFIG_NET_CLS_TCINDEX=y
CONFIG_NET_CLS_FW=y
CONFIG_NET_CLS_U32=y
# CONFIG_CLS_U32_PERF is not set
# CONFIG_CLS_U32_MARK is not set
CONFIG_NET_CLS_RSVP=y
CONFIG_NET_CLS_RSVP6=y
# CONFIG_NET_CLS_FLOW is not set
# CONFIG_NET_CLS_CGROUP is not set
CONFIG_NET_CLS_BPF=y
CONFIG_NET_CLS_FLOWER=y
CONFIG_NET_CLS_MATCHALL=y
# CONFIG_NET_EMATCH is not set
# CONFIG_NET_CLS_ACT is not set
CONFIG_NET_SCH_FIFO=y
CONFIG_DCB=y
# CONFIG_DNS_RESOLVER is not set
CONFIG_BATMAN_ADV=y
# CONFIG_BATMAN_ADV_BATMAN_V is not set
# CONFIG_BATMAN_ADV_NC is not set
CONFIG_BATMAN_ADV_DEBUG=y
CONFIG_VSOCKETS=y
CONFIG_VSOCKETS_DIAG=y
CONFIG_VSOCKETS_LOOPBACK=y
CONFIG_VIRTIO_VSOCKETS=y
CONFIG_VIRTIO_VSOCKETS_COMMON=y
CONFIG_NETLINK_DIAG=y
# CONFIG_MPLS is not set
# CONFIG_NET_NSH is not set
# CONFIG_HSR is not set
CONFIG_QRTR=y
CONFIG_QRTR_SMD=y
CONFIG_QRTR_TUN=y
CONFIG_QRTR_MHI=y
# CONFIG_CGROUP_NET_PRIO is not set
# CONFIG_CGROUP_NET_CLASSID is not set
CONFIG_NET_RX_BUSY_POLL=y
CONFIG_BQL=y

#
# Network testing
#
# end of Network testing
# end of Networking options

# CONFIG_HAMRADIO is not set
CONFIG_CAN=y
# CONFIG_CAN_RAW is not set
CONFIG_CAN_BCM=y
# CONFIG_CAN_GW is not set
CONFIG_CAN_J1939=y
CONFIG_CAN_ISOTP=y
CONFIG_BT=y
CONFIG_BT_BREDR=y
CONFIG_BT_RFCOMM=y
# CONFIG_BT_RFCOMM_TTY is not set
CONFIG_BT_BNEP=y
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_CMTP=y
CONFIG_BT_HIDP=y
# CONFIG_BT_HS is not set
# CONFIG_BT_LE is not set
# CONFIG_BT_LEDS is not set
# CONFIG_BT_MSFTEXT is not set
# CONFIG_BT_AOSPEXT is not set
CONFIG_BT_DEBUGFS=y

#
# Bluetooth device drivers
#
CONFIG_BT_INTEL=y
CONFIG_BT_BCM=y
CONFIG_BT_RTL=y
CONFIG_BT_QCA=y
CONFIG_BT_MTK=y
CONFIG_BT_HCIBTUSB=y
# CONFIG_BT_HCIBTUSB_AUTOSUSPEND is not set
# CONFIG_BT_HCIBTUSB_BCM is not set
# CONFIG_BT_HCIBTUSB_MTK is not set
CONFIG_BT_HCIBTUSB_RTL=y
CONFIG_BT_HCIBTSDIO=y
CONFIG_BT_HCIUART=y
CONFIG_BT_HCIUART_SERDEV=y
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIUART_ATH3K=y
CONFIG_BT_HCIUART_LL=y
CONFIG_BT_HCIUART_3WIRE=y
# CONFIG_BT_HCIUART_INTEL is not set
CONFIG_BT_HCIUART_BCM=y
CONFIG_BT_HCIUART_RTL=y
CONFIG_BT_HCIUART_QCA=y
# CONFIG_BT_HCIUART_AG6XX is not set
CONFIG_BT_HCIUART_MRVL=y
# CONFIG_BT_HCIBCM203X is not set
# CONFIG_BT_HCIBPA10X is not set
CONFIG_BT_HCIBFUSB=y
CONFIG_BT_HCIDTL1=y
CONFIG_BT_HCIBT3C=y
# CONFIG_BT_HCIBLUECARD is not set
CONFIG_BT_HCIVHCI=y
# CONFIG_BT_MRVL is not set
CONFIG_BT_ATH3K=y
# CONFIG_BT_MTKSDIO is not set
CONFIG_BT_MTKUART=y
CONFIG_BT_QCOMSMD=y
CONFIG_BT_VIRTIO=y
# end of Bluetooth device drivers

CONFIG_MCTP=y
CONFIG_WIRELESS=y
CONFIG_WIRELESS_EXT=y
CONFIG_WEXT_CORE=y
CONFIG_WEXT_PROC=y
CONFIG_WEXT_SPY=y
CONFIG_WEXT_PRIV=y
# CONFIG_CFG80211 is not set

#
# CFG80211 needs to be enabled for MAC80211
#
CONFIG_MAC80211_STA_HASH_MAX_SIZE=0
# CONFIG_RFKILL is not set
CONFIG_NET_9P=y
CONFIG_NET_9P_FD=y
CONFIG_NET_9P_VIRTIO=y
CONFIG_NET_9P_DEBUG=y
CONFIG_CAIF=y
CONFIG_CAIF_DEBUG=y
CONFIG_CAIF_NETDEV=y
CONFIG_CAIF_USB=y
# CONFIG_NFC is not set
CONFIG_PSAMPLE=y
# CONFIG_NET_IFE is not set
# CONFIG_LWTUNNEL is not set
CONFIG_GRO_CELLS=y
CONFIG_FAILOVER=y
# CONFIG_ETHTOOL_NETLINK is not set

#
# Device Drivers
#
CONFIG_PCCARD=y
CONFIG_PCMCIA=y
# CONFIG_PCMCIA_LOAD_CIS is not set

#
# PC-card bridges
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER=y
CONFIG_UEVENT_HELPER_PATH=""
CONFIG_DEVTMPFS=y
# CONFIG_DEVTMPFS_MOUNT is not set
# CONFIG_DEVTMPFS_SAFE is not set
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set

#
# Firmware loader
#
CONFIG_FW_LOADER=y
CONFIG_FW_LOADER_PAGED_BUF=y
CONFIG_FW_LOADER_SYSFS=y
CONFIG_EXTRA_FIRMWARE=""
CONFIG_FW_LOADER_USER_HELPER=y
# CONFIG_FW_LOADER_USER_HELPER_FALLBACK is not set
# CONFIG_FW_LOADER_COMPRESS is not set
# CONFIG_FW_UPLOAD is not set
# end of Firmware loader

CONFIG_WANT_DEV_COREDUMP=y
CONFIG_ALLOW_DEV_COREDUMP=y
CONFIG_DEV_COREDUMP=y
CONFIG_GENERIC_CPU_DEVICES=y
CONFIG_SOC_BUS=y
CONFIG_REGMAP=y
CONFIG_REGMAP_I2C=y
CONFIG_REGMAP_SLIMBUS=y
CONFIG_REGMAP_SPI=y
CONFIG_REGMAP_SPMI=y
CONFIG_REGMAP_W1=y
CONFIG_REGMAP_MMIO=y
CONFIG_REGMAP_IRQ=y
CONFIG_REGMAP_SCCB=y
CONFIG_REGMAP_I3C=y
CONFIG_DMA_SHARED_BUFFER=y
CONFIG_DMA_FENCE_TRACE=y
# end of Generic Driver Options

#
# Bus devices
#
# CONFIG_ARM_INTEGRATOR_LM is not set
CONFIG_BT1_APB=y
# CONFIG_BT1_AXI is not set
CONFIG_MOXTET=y
# CONFIG_HISILICON_LPC is not set
# CONFIG_INTEL_IXP4XX_EB is not set
CONFIG_QCOM_EBI2=y
CONFIG_MHI_BUS=y
CONFIG_MHI_BUS_DEBUG=y
# CONFIG_MHI_BUS_EP is not set
# end of Bus devices

CONFIG_CONNECTOR=y
# CONFIG_PROC_EVENTS is not set

#
# Firmware Drivers
#

#
# ARM System Control and Management Interface Protocol
#
CONFIG_ARM_SCMI_PROTOCOL=y
CONFIG_ARM_SCMI_HAVE_TRANSPORT=y
CONFIG_ARM_SCMI_HAVE_SHMEM=y
CONFIG_ARM_SCMI_HAVE_MSG=y
CONFIG_ARM_SCMI_TRANSPORT_MAILBOX=y
CONFIG_ARM_SCMI_TRANSPORT_VIRTIO=y
CONFIG_ARM_SCMI_TRANSPORT_VIRTIO_VERSION1_COMPLIANCE=y
# CONFIG_ARM_SCMI_TRANSPORT_VIRTIO_ATOMIC_ENABLE is not set
CONFIG_ARM_SCMI_POWER_DOMAIN=y
# CONFIG_ARM_SCMI_POWER_CONTROL is not set
# end of ARM System Control and Management Interface Protocol

CONFIG_ARM_SCPI_PROTOCOL=y
# CONFIG_ARM_SCPI_POWER_DOMAIN is not set
CONFIG_MTK_ADSP_IPC=y
CONFIG_QCOM_SCM=y
# CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT is not set
CONFIG_TURRIS_MOX_RWTM=y
CONFIG_BCM47XX_NVRAM=y
CONFIG_BCM47XX_SPROM=y
CONFIG_GOOGLE_FIRMWARE=y
CONFIG_GOOGLE_COREBOOT_TABLE=y
CONFIG_GOOGLE_MEMCONSOLE=y
CONFIG_GOOGLE_MEMCONSOLE_COREBOOT=y
# CONFIG_GOOGLE_VPD is not set

#
# Tegra firmware driver
#
# end of Tegra firmware driver
# end of Firmware Drivers

CONFIG_GNSS=y
CONFIG_GNSS_SERIAL=y
CONFIG_GNSS_MTK_SERIAL=y
CONFIG_GNSS_SIRF_SERIAL=y
# CONFIG_GNSS_UBX_SERIAL is not set
# CONFIG_GNSS_USB is not set
CONFIG_MTD=y

#
# Partition parsers
#
# CONFIG_MTD_AR7_PARTS is not set
CONFIG_MTD_BCM63XX_PARTS=y
# CONFIG_MTD_BRCM_U_BOOT is not set
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_OF_PARTS=y
# CONFIG_MTD_OF_PARTS_BCM4908 is not set
# CONFIG_MTD_OF_PARTS_LINKSYS_NS is not set
CONFIG_MTD_PARSER_IMAGETAG=y
# CONFIG_MTD_PARSER_TRX is not set
CONFIG_MTD_SHARPSL_PARTS=y
CONFIG_MTD_REDBOOT_PARTS=y
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
CONFIG_MTD_REDBOOT_PARTS_READONLY=y
# end of Partition parsers

#
# User Modules And Translation Layers
#
CONFIG_MTD_BLKDEVS=y
CONFIG_MTD_BLOCK=y

#
# Note that in some cases UBI block is preferred. See MTD_UBI_BLOCK.
#
CONFIG_FTL=y
CONFIG_NFTL=y
CONFIG_NFTL_RW=y
# CONFIG_INFTL is not set
CONFIG_RFD_FTL=y
CONFIG_SSFDC=y
# CONFIG_SM_FTL is not set
CONFIG_MTD_OOPS=y
CONFIG_MTD_PSTORE=y
CONFIG_MTD_PARTITIONED_MASTER=y

#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_GEN_PROBE=y
CONFIG_MTD_CFI_ADV_OPTIONS=y
# CONFIG_MTD_CFI_NOSWAP is not set
# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
CONFIG_MTD_CFI_LE_BYTE_SWAP=y
CONFIG_MTD_CFI_GEOMETRY=y
# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
CONFIG_MTD_MAP_BANK_WIDTH_2=y
# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
CONFIG_MTD_MAP_BANK_WIDTH_16=y
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
# CONFIG_MTD_CFI_I2 is not set
# CONFIG_MTD_CFI_I4 is not set
CONFIG_MTD_CFI_I8=y
CONFIG_MTD_OTP=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_CFI_STAA=y
CONFIG_MTD_CFI_UTIL=y
CONFIG_MTD_RAM=y
CONFIG_MTD_ROM=y
CONFIG_MTD_ABSENT=y
# end of RAM/ROM/Flash chip drivers

#
# Mapping drivers for chip access
#
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=y
# CONFIG_MTD_PHYSMAP_COMPAT is not set
# CONFIG_MTD_PHYSMAP_OF is not set
# CONFIG_MTD_PHYSMAP_GPIO_ADDR is not set
CONFIG_MTD_SC520CDP=y
CONFIG_MTD_NETSC520=y
CONFIG_MTD_TS5500=y
# CONFIG_MTD_PCMCIA is not set
CONFIG_MTD_UCLINUX=y
CONFIG_MTD_PLATRAM=y
# end of Mapping drivers for chip access

#
# Self-contained MTD device drivers
#
# CONFIG_MTD_DATAFLASH is not set
CONFIG_MTD_MCHP23K256=y
# CONFIG_MTD_MCHP48L640 is not set
CONFIG_MTD_SPEAR_SMI=y
CONFIG_MTD_SST25L=y
CONFIG_MTD_SLRAM=y
CONFIG_MTD_PHRAM=y
# CONFIG_MTD_MTDRAM is not set
CONFIG_MTD_BLOCK2MTD=y

#
# Disk-On-Chip Device Drivers
#
CONFIG_MTD_DOCG3=y
CONFIG_BCH_CONST_M=14
CONFIG_BCH_CONST_T=4
# end of Self-contained MTD device drivers

#
# NAND
#
CONFIG_MTD_NAND_CORE=y
CONFIG_MTD_ONENAND=y
# CONFIG_MTD_ONENAND_VERIFY_WRITE is not set
CONFIG_MTD_ONENAND_GENERIC=y
CONFIG_MTD_ONENAND_SAMSUNG=y
# CONFIG_MTD_ONENAND_OTP is not set
# CONFIG_MTD_ONENAND_2X_PROGRAM is not set
CONFIG_MTD_RAW_NAND=y

#
# Raw/parallel NAND flash controllers
#
CONFIG_MTD_NAND_DENALI=y
CONFIG_MTD_NAND_DENALI_DT=y
CONFIG_MTD_NAND_AMS_DELTA=y
CONFIG_MTD_NAND_OMAP2=y
CONFIG_MTD_NAND_OMAP_BCH=y
CONFIG_MTD_NAND_OMAP_BCH_BUILD=y
# CONFIG_MTD_NAND_SHARPSL is not set
CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_MARVELL is not set
CONFIG_MTD_NAND_SLC_LPC32XX=y
CONFIG_MTD_NAND_MLC_LPC32XX=y
# CONFIG_MTD_NAND_BRCMNAND is not set
# CONFIG_MTD_NAND_OXNAS is not set
CONFIG_MTD_NAND_FSL_IFC=y
# CONFIG_MTD_NAND_VF610_NFC is not set
CONFIG_MTD_NAND_MXC=y
CONFIG_MTD_NAND_SH_FLCTL=y
CONFIG_MTD_NAND_DAVINCI=y
# CONFIG_MTD_NAND_TXX9NDFMC is not set
CONFIG_MTD_NAND_JZ4780=y
CONFIG_MTD_NAND_INGENIC_ECC=y
# CONFIG_MTD_NAND_JZ4740_ECC is not set
CONFIG_MTD_NAND_JZ4725B_BCH=y
CONFIG_MTD_NAND_JZ4780_BCH=y
CONFIG_MTD_NAND_FSMC=y
CONFIG_MTD_NAND_SUNXI=y
# CONFIG_MTD_NAND_HISI504 is not set
CONFIG_MTD_NAND_QCOM=y
CONFIG_MTD_NAND_MXIC=y
# CONFIG_MTD_NAND_TEGRA is not set
CONFIG_MTD_NAND_STM32_FMC2=y
# CONFIG_MTD_NAND_GPIO is not set
CONFIG_MTD_NAND_PLATFORM=y
# CONFIG_MTD_NAND_CADENCE is not set
# CONFIG_MTD_NAND_ARASAN is not set
CONFIG_MTD_NAND_INTEL_LGM=y
# CONFIG_MTD_NAND_RENESAS is not set

#
# Misc
#
CONFIG_MTD_NAND_NANDSIM=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_SPI_NAND is not set

#
# ECC engine support
#
CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND_ECC_SW_HAMMING=y
CONFIG_MTD_NAND_ECC_SW_HAMMING_SMC=y
# CONFIG_MTD_NAND_ECC_SW_BCH is not set
CONFIG_MTD_NAND_ECC_MXIC=y
# CONFIG_MTD_NAND_ECC_MEDIATEK is not set
# end of ECC engine support
# end of NAND

#
# LPDDR & LPDDR2 PCM memory drivers
#
# CONFIG_MTD_LPDDR is not set
# end of LPDDR & LPDDR2 PCM memory drivers

CONFIG_MTD_SPI_NOR=y
# CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set
# CONFIG_MTD_SPI_NOR_SWP_DISABLE is not set
CONFIG_MTD_SPI_NOR_SWP_DISABLE_ON_VOLATILE=y
# CONFIG_MTD_SPI_NOR_SWP_KEEP is not set
CONFIG_SPI_HISI_SFC=y
CONFIG_SPI_NXP_SPIFI=y
# CONFIG_MTD_UBI is not set
CONFIG_MTD_HYPERBUS=y
# CONFIG_HBMC_AM654 is not set
CONFIG_DTC=y
CONFIG_OF=y
# CONFIG_OF_UNITTEST is not set
CONFIG_OF_ALL_DTBS=y
CONFIG_OF_FLATTREE=y
CONFIG_OF_KOBJ=y
CONFIG_OF_DYNAMIC=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_IRQ=y
CONFIG_OF_RESOLVE=y
CONFIG_OF_OVERLAY=y
CONFIG_PARPORT=y
# CONFIG_PARPORT_AX88796 is not set
# CONFIG_PARPORT_1284 is not set
CONFIG_PARPORT_NOT_PC=y
# CONFIG_BLK_DEV is not set

#
# NVME Support
#
CONFIG_NVME_CORE=y
CONFIG_NVME_MULTIPATH=y
# CONFIG_NVME_VERBOSE_ERRORS is not set
CONFIG_NVME_FABRICS=y
CONFIG_NVME_FC=y
# CONFIG_NVME_AUTH is not set
CONFIG_NVME_TARGET=y
CONFIG_NVME_TARGET_PASSTHRU=y
CONFIG_NVME_TARGET_LOOP=y
CONFIG_NVME_TARGET_FC=y
CONFIG_NVME_TARGET_FCLOOP=y
# CONFIG_NVME_TARGET_AUTH is not set
# end of NVME Support

#
# Misc devices
#
CONFIG_SENSORS_LIS3LV02D=y
CONFIG_AD525X_DPOT=y
CONFIG_AD525X_DPOT_I2C=y
# CONFIG_AD525X_DPOT_SPI is not set
CONFIG_DUMMY_IRQ=y
CONFIG_ICS932S401=y
# CONFIG_ATMEL_SSC is not set
CONFIG_ENCLOSURE_SERVICES=y
CONFIG_GEHC_ACHC=y
CONFIG_HI6421V600_IRQ=y
CONFIG_QCOM_COINCELL=y
CONFIG_QCOM_FASTRPC=y
CONFIG_APDS9802ALS=y
# CONFIG_ISL29003 is not set
CONFIG_ISL29020=y
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_SENSORS_BH1770 is not set
CONFIG_SENSORS_APDS990X=y
CONFIG_HMC6352=y
# CONFIG_DS1682 is not set
CONFIG_LATTICE_ECP3_CONFIG=y
# CONFIG_SRAM is not set
# CONFIG_XILINX_SDFEC is not set
CONFIG_MISC_RTSX=y
CONFIG_HISI_HIKEY_USB=y
# CONFIG_VCPU_STALL_DETECTOR is not set
CONFIG_C2PORT=y

#
# EEPROM support
#
CONFIG_EEPROM_AT24=y
CONFIG_EEPROM_AT25=y
# CONFIG_EEPROM_LEGACY is not set
CONFIG_EEPROM_MAX6875=y
CONFIG_EEPROM_93CX6=y
CONFIG_EEPROM_93XX46=y
# CONFIG_EEPROM_IDT_89HPESX is not set
CONFIG_EEPROM_EE1004=y
# end of EEPROM support

#
# Texas Instruments shared transport line discipline
#
# CONFIG_TI_ST is not set
# end of Texas Instruments shared transport line discipline

# CONFIG_SENSORS_LIS3_SPI is not set
CONFIG_SENSORS_LIS3_I2C=y
CONFIG_ALTERA_STAPL=y
CONFIG_ECHO=y
CONFIG_MISC_RTSX_USB=y
CONFIG_PVPANIC=y
CONFIG_PVPANIC_MMIO=y
# end of Misc devices

#
# SCSI device support
#
CONFIG_SCSI_MOD=y
CONFIG_RAID_ATTRS=y
CONFIG_SCSI_COMMON=y
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_SCSI_NETLINK=y
# CONFIG_SCSI_PROC_FS is not set

#
# SCSI support type (disk, tape, CD-ROM)
#
# CONFIG_BLK_DEV_SD is not set
# CONFIG_CHR_DEV_ST is not set
CONFIG_CHR_DEV_SG=y
CONFIG_BLK_DEV_BSG=y
CONFIG_CHR_DEV_SCH=y
# CONFIG_SCSI_ENCLOSURE is not set
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
# CONFIG_SCSI_SCAN_ASYNC is not set

#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=y
# CONFIG_SCSI_ISCSI_ATTRS is not set
CONFIG_SCSI_SAS_ATTRS=y
CONFIG_SCSI_SAS_LIBSAS=y
CONFIG_SCSI_SAS_ATA=y
CONFIG_SCSI_SAS_HOST_SMP=y
# CONFIG_SCSI_SRP_ATTRS is not set
# end of SCSI Transports

# CONFIG_SCSI_LOWLEVEL is not set
CONFIG_SCSI_DH=y
# CONFIG_SCSI_DH_RDAC is not set
CONFIG_SCSI_DH_HP_SW=y
# CONFIG_SCSI_DH_EMC is not set
CONFIG_SCSI_DH_ALUA=y
# end of SCSI device support

CONFIG_ATA=y
CONFIG_SATA_HOST=y
# CONFIG_ATA_VERBOSE_ERROR is not set
CONFIG_ATA_FORCE=y
CONFIG_SATA_PMP=y

#
# Controllers with non-SFF native interface
#
# CONFIG_SATA_AHCI_PLATFORM is not set
# CONFIG_AHCI_BRCM is not set
# CONFIG_AHCI_DA850 is not set
# CONFIG_AHCI_DM816 is not set
# CONFIG_AHCI_DWC is not set
# CONFIG_AHCI_ST is not set
CONFIG_AHCI_IMX=y
CONFIG_AHCI_CEVA=y
# CONFIG_AHCI_MTK is not set
# CONFIG_AHCI_MVEBU is not set
# CONFIG_AHCI_SUNXI is not set
# CONFIG_AHCI_TEGRA is not set
# CONFIG_AHCI_XGENE is not set
CONFIG_AHCI_QORIQ=y
# CONFIG_SATA_FSL is not set
CONFIG_SATA_GEMINI=y
# CONFIG_SATA_AHCI_SEATTLE is not set
CONFIG_ATA_SFF=y

#
# SFF controllers with custom DMA interface
#
CONFIG_ATA_BMDMA=y

#
# SATA SFF controllers with BMDMA
#
CONFIG_SATA_DWC=y
CONFIG_SATA_DWC_OLD_DMA=y
CONFIG_SATA_HIGHBANK=y
# CONFIG_SATA_MV is not set
CONFIG_SATA_RCAR=y

#
# PATA SFF controllers with BMDMA
#
CONFIG_PATA_ARASAN_CF=y
# CONFIG_PATA_BK3710 is not set
# CONFIG_PATA_FTIDE010 is not set
# CONFIG_PATA_IMX is not set
# CONFIG_PATA_PXA is not set

#
# PIO-only SFF controllers
#
CONFIG_PATA_IXP4XX_CF=y
CONFIG_PATA_PCMCIA=y
# CONFIG_PATA_OF_PLATFORM is not set
# CONFIG_PATA_SAMSUNG_CF is not set

#
# Generic fallback / legacy drivers
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
# CONFIG_MD_AUTODETECT is not set
CONFIG_MD_LINEAR=y
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
CONFIG_MD_RAID10=y
CONFIG_MD_RAID456=y
CONFIG_MD_MULTIPATH=y
CONFIG_MD_FAULTY=y
CONFIG_BCACHE=y
# CONFIG_BCACHE_DEBUG is not set
# CONFIG_BCACHE_CLOSURES_DEBUG is not set
CONFIG_BCACHE_ASYNC_REGISTRATION=y
CONFIG_BLK_DEV_DM_BUILTIN=y
CONFIG_BLK_DEV_DM=y
CONFIG_DM_DEBUG=y
CONFIG_DM_BUFIO=y
CONFIG_DM_DEBUG_BLOCK_MANAGER_LOCKING=y
CONFIG_DM_BIO_PRISON=y
CONFIG_DM_PERSISTENT_DATA=y
# CONFIG_DM_UNSTRIPED is not set
# CONFIG_DM_CRYPT is not set
CONFIG_DM_SNAPSHOT=y
CONFIG_DM_THIN_PROVISIONING=y
# CONFIG_DM_CACHE is not set
CONFIG_DM_WRITECACHE=y
CONFIG_DM_EBS=y
CONFIG_DM_ERA=y
CONFIG_DM_CLONE=y
CONFIG_DM_MIRROR=y
CONFIG_DM_LOG_USERSPACE=y
CONFIG_DM_RAID=y
CONFIG_DM_ZERO=y
# CONFIG_DM_MULTIPATH is not set
# CONFIG_DM_DELAY is not set
# CONFIG_DM_DUST is not set
CONFIG_DM_INIT=y
# CONFIG_DM_UEVENT is not set
CONFIG_DM_FLAKEY=y
CONFIG_DM_VERITY=y
CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG=y
CONFIG_DM_VERITY_FEC=y
CONFIG_DM_SWITCH=y
CONFIG_DM_LOG_WRITES=y
# CONFIG_DM_INTEGRITY is not set
CONFIG_DM_ZONED=y
# CONFIG_DM_AUDIT is not set
CONFIG_TARGET_CORE=y
CONFIG_TCM_IBLOCK=y
# CONFIG_TCM_FILEIO is not set
CONFIG_TCM_PSCSI=y
# CONFIG_LOOPBACK_TARGET is not set
CONFIG_SBP_TARGET=y

#
# IEEE 1394 (FireWire) support
#
CONFIG_FIREWIRE=y
# CONFIG_FIREWIRE_SBP2 is not set
# end of IEEE 1394 (FireWire) support

CONFIG_NETDEVICES=y
CONFIG_MII=y
CONFIG_NET_CORE=y
CONFIG_DUMMY=y
# CONFIG_EQUALIZER is not set
# CONFIG_NET_TEAM is not set
# CONFIG_MACVLAN is not set
CONFIG_MACSEC=y
# CONFIG_NETCONSOLE is not set
CONFIG_TUN_VNET_CROSS_LE=y
CONFIG_VETH=y
CONFIG_VIRTIO_NET=y
CONFIG_NLMON=y
CONFIG_VSOCKMON=y
CONFIG_MHI_NET=y
CONFIG_ARCNET=y
CONFIG_ARCNET_1201=y
CONFIG_ARCNET_1051=y
# CONFIG_ARCNET_RAW is not set
CONFIG_ARCNET_CAP=y
CONFIG_ARCNET_COM90xx=y
# CONFIG_ARCNET_COM90xxIO is not set
# CONFIG_ARCNET_RIM_I is not set
CONFIG_ARCNET_COM20020=y
CONFIG_ARCNET_COM20020_CS=y
CONFIG_CAIF_DRIVERS=y
CONFIG_CAIF_TTY=y
# CONFIG_CAIF_VIRTIO is not set
# CONFIG_ETHERNET is not set
CONFIG_PHYLIB=y
CONFIG_SWPHY=y
# CONFIG_LED_TRIGGER_PHY is not set
CONFIG_FIXED_PHY=y

#
# MII PHY device drivers
#
CONFIG_AMD_PHY=y
CONFIG_MESON_GXL_PHY=y
CONFIG_ADIN_PHY=y
# CONFIG_ADIN1100_PHY is not set
CONFIG_AQUANTIA_PHY=y
# CONFIG_AX88796B_PHY is not set
CONFIG_BROADCOM_PHY=y
CONFIG_BCM54140_PHY=y
CONFIG_BCM63XX_PHY=y
# CONFIG_BCM7XXX_PHY is not set
# CONFIG_BCM84881_PHY is not set
CONFIG_BCM87XX_PHY=y
CONFIG_BCM_CYGNUS_PHY=y
CONFIG_BCM_NET_PHYLIB=y
CONFIG_BCM_NET_PHYPTP=y
# CONFIG_CICADA_PHY is not set
# CONFIG_CORTINA_PHY is not set
# CONFIG_DAVICOM_PHY is not set
CONFIG_ICPLUS_PHY=y
CONFIG_LXT_PHY=y
CONFIG_INTEL_XWAY_PHY=y
CONFIG_LSI_ET1011C_PHY=y
CONFIG_MARVELL_PHY=y
# CONFIG_MARVELL_10G_PHY is not set
# CONFIG_MARVELL_88X2222_PHY is not set
# CONFIG_MAXLINEAR_GPHY is not set
# CONFIG_MEDIATEK_GE_PHY is not set
CONFIG_MICREL_PHY=y
CONFIG_MICROCHIP_PHY=y
CONFIG_MICROCHIP_T1_PHY=y
# CONFIG_MICROSEMI_PHY is not set
CONFIG_MOTORCOMM_PHY=y
CONFIG_NATIONAL_PHY=y
CONFIG_NXP_C45_TJA11XX_PHY=y
# CONFIG_AT803X_PHY is not set
CONFIG_QSEMI_PHY=y
# CONFIG_REALTEK_PHY is not set
CONFIG_RENESAS_PHY=y
CONFIG_ROCKCHIP_PHY=y
CONFIG_SMSC_PHY=y
# CONFIG_STE10XP is not set
# CONFIG_TERANETICS_PHY is not set
CONFIG_DP83822_PHY=y
CONFIG_DP83TC811_PHY=y
CONFIG_DP83848_PHY=y
CONFIG_DP83867_PHY=y
# CONFIG_DP83869_PHY is not set
# CONFIG_DP83TD510_PHY is not set
# CONFIG_VITESSE_PHY is not set
CONFIG_XILINX_GMII2RGMII=y
CONFIG_MICREL_KS8995MA=y
# CONFIG_PSE_CONTROLLER is not set
CONFIG_CAN_DEV=y
CONFIG_CAN_VCAN=y
CONFIG_CAN_VXCAN=y
CONFIG_CAN_NETLINK=y
# CONFIG_CAN_CALC_BITTIMING is not set
CONFIG_CAN_RX_OFFLOAD=y
CONFIG_CAN_AT91=y
# CONFIG_CAN_CAN327 is not set
# CONFIG_CAN_FLEXCAN is not set
CONFIG_CAN_GRCAN=y
# CONFIG_CAN_SLCAN is not set
# CONFIG_CAN_SUN4I is not set
CONFIG_CAN_C_CAN=y
CONFIG_CAN_C_CAN_PLATFORM=y
CONFIG_CAN_CC770=y
# CONFIG_CAN_CC770_ISA is not set
CONFIG_CAN_CC770_PLATFORM=y
# CONFIG_CAN_CTUCANFD is not set
# CONFIG_CAN_CTUCANFD_PLATFORM is not set
CONFIG_CAN_IFI_CANFD=y
# CONFIG_CAN_M_CAN is not set
CONFIG_CAN_RCAR=y
CONFIG_CAN_RCAR_CANFD=y
# CONFIG_CAN_SJA1000 is not set
CONFIG_CAN_SOFTING=y
# CONFIG_CAN_SOFTING_CS is not set

#
# CAN SPI interfaces
#
# CONFIG_CAN_HI311X is not set
CONFIG_CAN_MCP251X=y
CONFIG_CAN_MCP251XFD=y
CONFIG_CAN_MCP251XFD_SANITY=y
# end of CAN SPI interfaces

#
# CAN USB interfaces
#
CONFIG_CAN_8DEV_USB=y
# CONFIG_CAN_EMS_USB is not set
# CONFIG_CAN_ESD_USB is not set
CONFIG_CAN_ETAS_ES58X=y
# CONFIG_CAN_GS_USB is not set
# CONFIG_CAN_KVASER_USB is not set
CONFIG_CAN_MCBA_USB=y
CONFIG_CAN_PEAK_USB=y
CONFIG_CAN_UCAN=y
# end of CAN USB interfaces

# CONFIG_CAN_DEBUG_DEVICES is not set

#
# MCTP Device Drivers
#
# CONFIG_MCTP_SERIAL is not set
# CONFIG_MCTP_TRANSPORT_I2C is not set
# end of MCTP Device Drivers

CONFIG_MDIO_DEVICE=y
CONFIG_MDIO_BUS=y
CONFIG_FWNODE_MDIO=y
CONFIG_OF_MDIO=y
CONFIG_MDIO_DEVRES=y
CONFIG_MDIO_SUN4I=y
CONFIG_MDIO_XGENE=y
CONFIG_MDIO_ASPEED=y
# CONFIG_MDIO_BITBANG is not set
CONFIG_MDIO_BCM_IPROC=y
# CONFIG_MDIO_BCM_UNIMAC is not set
CONFIG_MDIO_CAVIUM=y
CONFIG_MDIO_HISI_FEMAC=y
# CONFIG_MDIO_MVUSB is not set
CONFIG_MDIO_MSCC_MIIM=y
CONFIG_MDIO_MOXART=y
CONFIG_MDIO_OCTEON=y
CONFIG_MDIO_IPQ8064=y

#
# MDIO Multiplexers
#
CONFIG_MDIO_BUS_MUX=y
CONFIG_MDIO_BUS_MUX_BCM6368=y
CONFIG_MDIO_BUS_MUX_BCM_IPROC=y
CONFIG_MDIO_BUS_MUX_GPIO=y
CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
CONFIG_MDIO_BUS_MUX_MMIOREG=y

#
# PCS device drivers
#
# CONFIG_PCS_RZN1_MIIC is not set
# end of PCS device drivers

CONFIG_PLIP=y
CONFIG_PPP=y
CONFIG_PPP_BSDCOMP=y
# CONFIG_PPP_DEFLATE is not set
CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=y
# CONFIG_PPP_MULTILINK is not set
# CONFIG_PPPOE is not set
# CONFIG_PPP_ASYNC is not set
# CONFIG_PPP_SYNC_TTY is not set
CONFIG_SLIP=y
CONFIG_SLHC=y
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
# CONFIG_SLIP_MODE_SLIP6 is not set
CONFIG_USB_NET_DRIVERS=y
CONFIG_USB_CATC=y
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
CONFIG_USB_RTL8150=y
CONFIG_USB_RTL8152=y
CONFIG_USB_LAN78XX=y
# CONFIG_USB_USBNET is not set
# CONFIG_USB_IPHETH is not set
CONFIG_WLAN=y
CONFIG_WLAN_VENDOR_ADMTEK=y
# CONFIG_WLAN_VENDOR_ATH is not set
CONFIG_WLAN_VENDOR_ATMEL=y
CONFIG_WLAN_VENDOR_BROADCOM=y
# CONFIG_WLAN_VENDOR_CISCO is not set
CONFIG_WLAN_VENDOR_INTEL=y
CONFIG_WLAN_VENDOR_INTERSIL=y
# CONFIG_HOSTAP is not set
CONFIG_WLAN_VENDOR_MARVELL=y
# CONFIG_WLAN_VENDOR_MEDIATEK is not set
CONFIG_WLAN_VENDOR_MICROCHIP=y
CONFIG_WLAN_VENDOR_PURELIFI=y
# CONFIG_WLAN_VENDOR_RALINK is not set
# CONFIG_WLAN_VENDOR_REALTEK is not set
# CONFIG_WLAN_VENDOR_RSI is not set
CONFIG_WLAN_VENDOR_SILABS=y
# CONFIG_WLAN_VENDOR_ST is not set
CONFIG_WLAN_VENDOR_TI=y
# CONFIG_WLAN_VENDOR_ZYDAS is not set
# CONFIG_WLAN_VENDOR_QUANTENNA is not set
CONFIG_PCMCIA_RAYCS=y
CONFIG_WAN=y
# CONFIG_HDLC is not set
CONFIG_SLIC_DS26522=y
CONFIG_LAPBETHER=y

#
# Wireless WAN
#
CONFIG_WWAN=y
CONFIG_WWAN_DEBUGFS=y
CONFIG_WWAN_HWSIM=y
CONFIG_MHI_WWAN_CTRL=y
CONFIG_MHI_WWAN_MBIM=y
# CONFIG_QCOM_BAM_DMUX is not set
CONFIG_RPMSG_WWAN_CTRL=y
# end of Wireless WAN

CONFIG_NET_FAILOVER=y
CONFIG_ISDN=y
CONFIG_ISDN_CAPI=y
CONFIG_CAPI_TRACE=y
CONFIG_ISDN_CAPI_MIDDLEWARE=y
# CONFIG_MISDN is not set

#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_LEDS=y
CONFIG_INPUT_FF_MEMLESS=y
CONFIG_INPUT_SPARSEKMAP=y
# CONFIG_INPUT_MATRIXKMAP is not set
CONFIG_INPUT_VIVALDIFMAP=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=y
# CONFIG_INPUT_EVDEV is not set
CONFIG_INPUT_EVBUG=y

#
# Input Device Drivers
#
# CONFIG_INPUT_KEYBOARD is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_BYD=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS=y
CONFIG_MOUSE_PS2_CYPRESS=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
CONFIG_MOUSE_PS2_ELANTECH=y
CONFIG_MOUSE_PS2_ELANTECH_SMBUS=y
CONFIG_MOUSE_PS2_SENTELIC=y
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
CONFIG_MOUSE_PS2_FOCALTECH=y
CONFIG_MOUSE_PS2_SMBUS=y
CONFIG_MOUSE_SERIAL=y
# CONFIG_MOUSE_APPLETOUCH is not set
CONFIG_MOUSE_BCM5974=y
CONFIG_MOUSE_CYAPA=y
CONFIG_MOUSE_ELAN_I2C=y
# CONFIG_MOUSE_ELAN_I2C_I2C is not set
CONFIG_MOUSE_ELAN_I2C_SMBUS=y
CONFIG_MOUSE_VSXXXAA=y
# CONFIG_MOUSE_GPIO is not set
# CONFIG_MOUSE_SYNAPTICS_I2C is not set
# CONFIG_MOUSE_SYNAPTICS_USB is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_88PM860X is not set
CONFIG_TOUCHSCREEN_ADS7846=y
CONFIG_TOUCHSCREEN_AD7877=y
# CONFIG_TOUCHSCREEN_AD7879 is not set
CONFIG_TOUCHSCREEN_ADC=y
CONFIG_TOUCHSCREEN_AR1021_I2C=y
# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set
CONFIG_TOUCHSCREEN_AUO_PIXCIR=y
# CONFIG_TOUCHSCREEN_BU21013 is not set
# CONFIG_TOUCHSCREEN_BU21029 is not set
CONFIG_TOUCHSCREEN_CHIPONE_ICN8318=y
CONFIG_TOUCHSCREEN_CY8CTMA140=y
# CONFIG_TOUCHSCREEN_CY8CTMG110 is not set
# CONFIG_TOUCHSCREEN_CYTTSP_CORE is not set
CONFIG_TOUCHSCREEN_CYTTSP4_CORE=y
# CONFIG_TOUCHSCREEN_CYTTSP4_I2C is not set
CONFIG_TOUCHSCREEN_CYTTSP4_SPI=y
CONFIG_TOUCHSCREEN_DA9052=y
CONFIG_TOUCHSCREEN_DYNAPRO=y
CONFIG_TOUCHSCREEN_HAMPSHIRE=y
CONFIG_TOUCHSCREEN_EETI=y
CONFIG_TOUCHSCREEN_EGALAX=y
# CONFIG_TOUCHSCREEN_EGALAX_SERIAL is not set
# CONFIG_TOUCHSCREEN_EXC3000 is not set
CONFIG_TOUCHSCREEN_FUJITSU=y
CONFIG_TOUCHSCREEN_GOODIX=y
CONFIG_TOUCHSCREEN_HIDEEP=y
# CONFIG_TOUCHSCREEN_HYCON_HY46XX is not set
# CONFIG_TOUCHSCREEN_ILI210X is not set
# CONFIG_TOUCHSCREEN_ILITEK is not set
# CONFIG_TOUCHSCREEN_IPROC is not set
# CONFIG_TOUCHSCREEN_S6SY761 is not set
CONFIG_TOUCHSCREEN_GUNZE=y
CONFIG_TOUCHSCREEN_EKTF2127=y
# CONFIG_TOUCHSCREEN_ELAN is not set
# CONFIG_TOUCHSCREEN_ELO is not set
CONFIG_TOUCHSCREEN_WACOM_W8001=y
CONFIG_TOUCHSCREEN_WACOM_I2C=y
CONFIG_TOUCHSCREEN_MAX11801=y
# CONFIG_TOUCHSCREEN_MCS5000 is not set
CONFIG_TOUCHSCREEN_MMS114=y
CONFIG_TOUCHSCREEN_MELFAS_MIP4=y
CONFIG_TOUCHSCREEN_MSG2638=y
CONFIG_TOUCHSCREEN_MTOUCH=y
# CONFIG_TOUCHSCREEN_IMAGIS is not set
CONFIG_TOUCHSCREEN_IMX6UL_TSC=y
# CONFIG_TOUCHSCREEN_INEXIO is not set
CONFIG_TOUCHSCREEN_MK712=y
CONFIG_TOUCHSCREEN_PENMOUNT=y
CONFIG_TOUCHSCREEN_EDT_FT5X06=y
CONFIG_TOUCHSCREEN_RASPBERRYPI_FW=y
CONFIG_TOUCHSCREEN_MIGOR=y
# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
CONFIG_TOUCHSCREEN_TOUCHWIN=y
# CONFIG_TOUCHSCREEN_TI_AM335X_TSC is not set
CONFIG_TOUCHSCREEN_PIXCIR=y
CONFIG_TOUCHSCREEN_WDT87XX_I2C=y
# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
CONFIG_TOUCHSCREEN_MXS_LRADC=y
# CONFIG_TOUCHSCREEN_MC13783 is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
CONFIG_TOUCHSCREEN_TS4800=y
# CONFIG_TOUCHSCREEN_TSC_SERIO is not set
CONFIG_TOUCHSCREEN_TSC200X_CORE=y
CONFIG_TOUCHSCREEN_TSC2004=y
CONFIG_TOUCHSCREEN_TSC2005=y
# CONFIG_TOUCHSCREEN_TSC2007 is not set
CONFIG_TOUCHSCREEN_PCAP=y
CONFIG_TOUCHSCREEN_RM_TS=y
CONFIG_TOUCHSCREEN_SILEAD=y
CONFIG_TOUCHSCREEN_SIS_I2C=y
# CONFIG_TOUCHSCREEN_ST1232 is not set
# CONFIG_TOUCHSCREEN_STMFTS is not set
CONFIG_TOUCHSCREEN_SURFACE3_SPI=y
# CONFIG_TOUCHSCREEN_SX8654 is not set
# CONFIG_TOUCHSCREEN_TPS6507X is not set
# CONFIG_TOUCHSCREEN_ZET6223 is not set
CONFIG_TOUCHSCREEN_ZFORCE=y
# CONFIG_TOUCHSCREEN_COLIBRI_VF50 is not set
CONFIG_TOUCHSCREEN_ROHM_BU21023=y
CONFIG_TOUCHSCREEN_IQS5XX=y
CONFIG_TOUCHSCREEN_ZINITIX=y
CONFIG_INPUT_MISC=y
# CONFIG_INPUT_88PM860X_ONKEY is not set
# CONFIG_INPUT_88PM80X_ONKEY is not set
CONFIG_INPUT_AD714X=y
CONFIG_INPUT_AD714X_I2C=y
CONFIG_INPUT_AD714X_SPI=y
# CONFIG_INPUT_ARIEL_PWRBUTTON is not set
CONFIG_INPUT_ATC260X_ONKEY=y
# CONFIG_INPUT_ATMEL_CAPTOUCH is not set
# CONFIG_INPUT_BMA150 is not set
# CONFIG_INPUT_E3X0_BUTTON is not set
CONFIG_INPUT_PM8941_PWRKEY=y
CONFIG_INPUT_PM8XXX_VIBRATOR=y
CONFIG_INPUT_M68K_BEEP=y
CONFIG_INPUT_MC13783_PWRBUTTON=y
# CONFIG_INPUT_MMA8450 is not set
CONFIG_INPUT_GPIO_BEEPER=y
# CONFIG_INPUT_GPIO_DECODER is not set
CONFIG_INPUT_GPIO_VIBRA=y
CONFIG_INPUT_ATI_REMOTE2=y
CONFIG_INPUT_KEYSPAN_REMOTE=y
CONFIG_INPUT_KXTJ9=y
CONFIG_INPUT_POWERMATE=y
CONFIG_INPUT_YEALINK=y
# CONFIG_INPUT_CM109 is not set
# CONFIG_INPUT_REGULATOR_HAPTIC is not set
CONFIG_INPUT_RETU_PWRBUTTON=y
# CONFIG_INPUT_TPS65218_PWRBUTTON is not set
# CONFIG_INPUT_AXP20X_PEK is not set
# CONFIG_INPUT_TWL4030_PWRBUTTON is not set
CONFIG_INPUT_TWL4030_VIBRA=y
CONFIG_INPUT_UINPUT=y
# CONFIG_INPUT_PALMAS_PWRBUTTON is not set
CONFIG_INPUT_PCF8574=y
CONFIG_INPUT_GPIO_ROTARY_ENCODER=y
# CONFIG_INPUT_DA7280_HAPTICS is not set
# CONFIG_INPUT_DA9052_ONKEY is not set
CONFIG_INPUT_DA9055_ONKEY=y
CONFIG_INPUT_DA9063_ONKEY=y
# CONFIG_INPUT_PCAP is not set
# CONFIG_INPUT_ADXL34X is not set
# CONFIG_INPUT_IBM_PANEL is not set
CONFIG_INPUT_IMS_PCU=y
CONFIG_INPUT_IQS269A=y
CONFIG_INPUT_IQS626A=y
# CONFIG_INPUT_IQS7222 is not set
CONFIG_INPUT_CMA3000=y
# CONFIG_INPUT_CMA3000_I2C is not set
CONFIG_INPUT_DRV260X_HAPTICS=y
# CONFIG_INPUT_DRV2665_HAPTICS is not set
# CONFIG_INPUT_DRV2667_HAPTICS is not set
# CONFIG_INPUT_HISI_POWERKEY is not set
CONFIG_INPUT_RAVE_SP_PWRBUTTON=y
CONFIG_INPUT_SC27XX_VIBRA=y
# CONFIG_INPUT_RT5120_PWRKEY is not set
CONFIG_INPUT_STPMIC1_ONKEY=y
CONFIG_RMI4_CORE=y
# CONFIG_RMI4_I2C is not set
# CONFIG_RMI4_SPI is not set
CONFIG_RMI4_SMB=y
CONFIG_RMI4_F03=y
CONFIG_RMI4_F03_SERIO=y
CONFIG_RMI4_2D_SENSOR=y
CONFIG_RMI4_F11=y
CONFIG_RMI4_F12=y
CONFIG_RMI4_F30=y
# CONFIG_RMI4_F34 is not set
# CONFIG_RMI4_F3A is not set
# CONFIG_RMI4_F54 is not set
# CONFIG_RMI4_F55 is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=y
CONFIG_SERIO_ALTERA_PS2=y
CONFIG_SERIO_PS2MULT=y
CONFIG_SERIO_ARC_PS2=y
CONFIG_SERIO_APBPS2=y
CONFIG_SERIO_OLPC_APSP=y
# CONFIG_SERIO_SUN4I_PS2 is not set
CONFIG_SERIO_GPIO_PS2=y
# CONFIG_USERIO is not set
# CONFIG_GAMEPORT is not set
# end of Hardware I/O ports
# end of Input device support

#
# Character devices
#
CONFIG_TTY=y
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_LDISC_AUTOLOAD is not set

#
# Serial drivers
#
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
# CONFIG_SERIAL_8250_16550A_VARIANTS is not set
# CONFIG_SERIAL_8250_FINTEK is not set
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_DMA=y
CONFIG_SERIAL_8250_CS=y
# CONFIG_SERIAL_8250_MEN_MCB is not set
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
# CONFIG_SERIAL_8250_MANY_PORTS is not set
CONFIG_SERIAL_8250_ASPEED_VUART=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
# CONFIG_SERIAL_8250_RSA is not set
CONFIG_SERIAL_8250_DWLIB=y
CONFIG_SERIAL_8250_BCM2835AUX=y
CONFIG_SERIAL_8250_FSL=y
CONFIG_SERIAL_8250_DW=y
CONFIG_SERIAL_8250_EM=y
CONFIG_SERIAL_8250_IOC3=y
# CONFIG_SERIAL_8250_RT288X is not set
CONFIG_SERIAL_8250_OMAP=y
CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP=y
# CONFIG_SERIAL_8250_LPC18XX is not set
CONFIG_SERIAL_8250_MT6577=y
CONFIG_SERIAL_8250_UNIPHIER=y
# CONFIG_SERIAL_8250_INGENIC is not set
CONFIG_SERIAL_8250_PXA=y
# CONFIG_SERIAL_8250_TEGRA is not set
CONFIG_SERIAL_8250_BCM7271=y
CONFIG_SERIAL_OF_PLATFORM=y

#
# Non-8250 serial port support
#
CONFIG_SERIAL_AMBA_PL010=y
# CONFIG_SERIAL_AMBA_PL010_CONSOLE is not set
# CONFIG_SERIAL_MESON is not set
CONFIG_SERIAL_CLPS711X=y
CONFIG_SERIAL_CLPS711X_CONSOLE=y
CONFIG_SERIAL_SAMSUNG=y
CONFIG_SERIAL_SAMSUNG_UARTS_4=y
CONFIG_SERIAL_SAMSUNG_UARTS=4
CONFIG_SERIAL_SAMSUNG_CONSOLE=y
CONFIG_SERIAL_TEGRA=y
# CONFIG_SERIAL_TEGRA_TCU is not set
# CONFIG_SERIAL_MAX3100 is not set
CONFIG_SERIAL_MAX310X=y
CONFIG_SERIAL_IMX=y
CONFIG_SERIAL_IMX_CONSOLE=y
CONFIG_SERIAL_IMX_EARLYCON=y
# CONFIG_SERIAL_UARTLITE is not set
# CONFIG_SERIAL_SH_SCI is not set
# CONFIG_SERIAL_HS_LPC32XX is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_MCF is not set
CONFIG_SERIAL_MSM=y
# CONFIG_SERIAL_MSM_CONSOLE is not set
# CONFIG_SERIAL_QCOM_GENI is not set
# CONFIG_SERIAL_VT8500 is not set
CONFIG_SERIAL_OMAP=y
# CONFIG_SERIAL_OMAP_CONSOLE is not set
CONFIG_SERIAL_SIFIVE=y
# CONFIG_SERIAL_SIFIVE_CONSOLE is not set
CONFIG_SERIAL_LANTIQ=y
# CONFIG_SERIAL_LANTIQ_CONSOLE is not set
CONFIG_SERIAL_QE=y
CONFIG_SERIAL_SCCNXP=y
# CONFIG_SERIAL_SCCNXP_CONSOLE is not set
# CONFIG_SERIAL_SC16IS7XX is not set
CONFIG_SERIAL_TIMBERDALE=y
# CONFIG_SERIAL_BCM63XX is not set
CONFIG_SERIAL_ALTERA_JTAGUART=y
# CONFIG_SERIAL_ALTERA_JTAGUART_CONSOLE is not set
CONFIG_SERIAL_ALTERA_UART=y
CONFIG_SERIAL_ALTERA_UART_MAXPORTS=4
CONFIG_SERIAL_ALTERA_UART_BAUDRATE=115200
# CONFIG_SERIAL_ALTERA_UART_CONSOLE is not set
# CONFIG_SERIAL_MXS_AUART is not set
# CONFIG_SERIAL_XILINX_PS_UART is not set
CONFIG_SERIAL_MPS2_UART_CONSOLE=y
CONFIG_SERIAL_MPS2_UART=y
# CONFIG_SERIAL_ARC is not set
# CONFIG_SERIAL_FSL_LPUART is not set
CONFIG_SERIAL_FSL_LINFLEXUART=y
# CONFIG_SERIAL_FSL_LINFLEXUART_CONSOLE is not set
CONFIG_SERIAL_CONEXANT_DIGICOLOR=y
CONFIG_SERIAL_CONEXANT_DIGICOLOR_CONSOLE=y
CONFIG_SERIAL_ST_ASC=y
# CONFIG_SERIAL_ST_ASC_CONSOLE is not set
# CONFIG_SERIAL_MEN_Z135 is not set
CONFIG_SERIAL_STM32=y
CONFIG_SERIAL_STM32_CONSOLE=y
CONFIG_SERIAL_OWL=y
CONFIG_SERIAL_OWL_CONSOLE=y
CONFIG_SERIAL_RDA=y
# CONFIG_SERIAL_RDA_CONSOLE is not set
CONFIG_SERIAL_MILBEAUT_USIO=y
CONFIG_SERIAL_MILBEAUT_USIO_PORTS=4
CONFIG_SERIAL_MILBEAUT_USIO_CONSOLE=y
CONFIG_SERIAL_LITEUART=y
CONFIG_SERIAL_LITEUART_MAX_PORTS=1
CONFIG_SERIAL_LITEUART_CONSOLE=y
# CONFIG_SERIAL_SUNPLUS is not set
# end of Serial drivers

CONFIG_SERIAL_MCTRL_GPIO=y
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_GOLDFISH_TTY=y
CONFIG_GOLDFISH_TTY_EARLY_CONSOLE=y
CONFIG_N_GSM=y
# CONFIG_NULL_TTY is not set
CONFIG_HVC_DRIVER=y
# CONFIG_RPMSG_TTY is not set
CONFIG_SERIAL_DEV_BUS=y
CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
CONFIG_PRINTER=y
# CONFIG_LP_CONSOLE is not set
CONFIG_PPDEV=y
CONFIG_VIRTIO_CONSOLE=y
# CONFIG_IPMI_HANDLER is not set
CONFIG_IPMI_KCS_BMC=y
CONFIG_ASPEED_KCS_IPMI_BMC=y
CONFIG_NPCM7XX_KCS_IPMI_BMC=y
CONFIG_IPMI_KCS_BMC_CDEV_IPMI=y
# CONFIG_IPMI_KCS_BMC_SERIO is not set
CONFIG_ASPEED_BT_IPMI_BMC=y
# CONFIG_IPMB_DEVICE_INTERFACE is not set
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_TIMERIOMEM is not set
CONFIG_HW_RANDOM_ATMEL=y
CONFIG_HW_RANDOM_BA431=y
CONFIG_HW_RANDOM_BCM2835=y
CONFIG_HW_RANDOM_IPROC_RNG200=y
CONFIG_HW_RANDOM_IXP4XX=y
CONFIG_HW_RANDOM_OMAP=y
CONFIG_HW_RANDOM_OMAP3_ROM=y
CONFIG_HW_RANDOM_VIRTIO=y
CONFIG_HW_RANDOM_IMX_RNGC=y
CONFIG_HW_RANDOM_NOMADIK=y
CONFIG_HW_RANDOM_STM32=y
CONFIG_HW_RANDOM_MESON=y
CONFIG_HW_RANDOM_MTK=y
CONFIG_HW_RANDOM_EXYNOS=y
CONFIG_HW_RANDOM_NPCM=y
# CONFIG_HW_RANDOM_KEYSTONE is not set
# CONFIG_HW_RANDOM_CCTRNG is not set
# CONFIG_HW_RANDOM_XIPHERA is not set

#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
CONFIG_CARDMAN_4000=y
CONFIG_CARDMAN_4040=y
CONFIG_SCR24X=y
CONFIG_IPWIRELESS=y
# end of PCMCIA character devices

CONFIG_DEVMEM=y
CONFIG_TCG_TPM=y
# CONFIG_HW_RANDOM_TPM is not set
CONFIG_TCG_TIS_CORE=y
CONFIG_TCG_TIS=y
CONFIG_TCG_TIS_SPI=y
CONFIG_TCG_TIS_SPI_CR50=y
# CONFIG_TCG_TIS_I2C is not set
# CONFIG_TCG_TIS_SYNQUACER is not set
CONFIG_TCG_TIS_I2C_CR50=y
CONFIG_TCG_TIS_I2C_ATMEL=y
CONFIG_TCG_TIS_I2C_INFINEON=y
# CONFIG_TCG_TIS_I2C_NUVOTON is not set
CONFIG_TCG_VTPM_PROXY=y
CONFIG_TCG_TIS_ST33ZP24=y
CONFIG_TCG_TIS_ST33ZP24_I2C=y
CONFIG_TCG_TIS_ST33ZP24_SPI=y
CONFIG_XILLYBUS_CLASS=y
# CONFIG_XILLYBUS is not set
CONFIG_XILLYUSB=y
CONFIG_RANDOM_TRUST_CPU=y
CONFIG_RANDOM_TRUST_BOOTLOADER=y
# end of Character devices

#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_MUX=y

#
# Multiplexer I2C Chip support
#
CONFIG_I2C_ARB_GPIO_CHALLENGE=y
CONFIG_I2C_MUX_GPIO=y
CONFIG_I2C_MUX_GPMUX=y
CONFIG_I2C_MUX_LTC4306=y
CONFIG_I2C_MUX_PCA9541=y
CONFIG_I2C_MUX_PCA954x=y
# CONFIG_I2C_MUX_PINCTRL is not set
# CONFIG_I2C_MUX_REG is not set
# CONFIG_I2C_DEMUX_PINCTRL is not set
# CONFIG_I2C_MUX_MLXCPLD is not set
# end of Multiplexer I2C Chip support

CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_SMBUS=y
CONFIG_I2C_ALGOBIT=y
CONFIG_I2C_ALGOPCA=y

#
# I2C Hardware Bus support
#
CONFIG_I2C_HIX5HD2=y

#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
CONFIG_I2C_ALTERA=y
CONFIG_I2C_ASPEED=y
CONFIG_I2C_AT91=y
CONFIG_I2C_AT91_SLAVE_EXPERIMENTAL=y
CONFIG_I2C_AXXIA=y
CONFIG_I2C_BCM_IPROC=y
# CONFIG_I2C_BCM_KONA is not set
CONFIG_I2C_BRCMSTB=y
CONFIG_I2C_CADENCE=y
CONFIG_I2C_CBUS_GPIO=y
CONFIG_I2C_DAVINCI=y
CONFIG_I2C_DESIGNWARE_CORE=y
# CONFIG_I2C_DESIGNWARE_SLAVE is not set
CONFIG_I2C_DESIGNWARE_PLATFORM=y
CONFIG_I2C_DIGICOLOR=y
CONFIG_I2C_EMEV2=y
CONFIG_I2C_EXYNOS5=y
# CONFIG_I2C_GPIO is not set
CONFIG_I2C_HIGHLANDER=y
# CONFIG_I2C_HISI is not set
CONFIG_I2C_IMG=y
# CONFIG_I2C_IMX is not set
CONFIG_I2C_IMX_LPI2C=y
# CONFIG_I2C_IOP3XX is not set
# CONFIG_I2C_JZ4780 is not set
CONFIG_I2C_LPC2K=y
# CONFIG_I2C_MICROCHIP_CORE is not set
CONFIG_I2C_MT65XX=y
CONFIG_I2C_MT7621=y
CONFIG_I2C_MV64XXX=y
# CONFIG_I2C_MXS is not set
# CONFIG_I2C_NPCM is not set
CONFIG_I2C_OCORES=y
CONFIG_I2C_OMAP=y
CONFIG_I2C_OWL=y
# CONFIG_I2C_APPLE is not set
CONFIG_I2C_PCA_PLATFORM=y
CONFIG_I2C_PNX=y
# CONFIG_I2C_PXA is not set
CONFIG_I2C_QCOM_CCI=y
CONFIG_I2C_QCOM_GENI=y
CONFIG_I2C_QUP=y
# CONFIG_I2C_RIIC is not set
# CONFIG_I2C_RZV2M is not set
CONFIG_I2C_S3C2410=y
CONFIG_I2C_SH_MOBILE=y
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_ST is not set
CONFIG_I2C_STM32F4=y
CONFIG_I2C_STM32F7=y
# CONFIG_I2C_SUN6I_P2WI is not set
CONFIG_I2C_SYNQUACER=y
CONFIG_I2C_TEGRA=y
CONFIG_I2C_TEGRA_BPMP=y
CONFIG_I2C_UNIPHIER=y
CONFIG_I2C_UNIPHIER_F=y
# CONFIG_I2C_VERSATILE is not set
CONFIG_I2C_WMT=y
# CONFIG_I2C_XILINX is not set
CONFIG_I2C_XLP9XX=y
# CONFIG_I2C_RCAR is not set

#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_DIOLAN_U2C is not set
CONFIG_I2C_CP2615=y
CONFIG_I2C_PARPORT=y
CONFIG_I2C_ROBOTFUZZ_OSIF=y
# CONFIG_I2C_TAOS_EVM is not set
CONFIG_I2C_TINY_USB=y

#
# Other I2C/SMBus bus drivers
#
CONFIG_I2C_MLXCPLD=y
CONFIG_I2C_CROS_EC_TUNNEL=y
CONFIG_I2C_FSI=y
CONFIG_I2C_VIRTIO=y
# end of I2C Hardware Bus support

CONFIG_I2C_SLAVE=y
CONFIG_I2C_SLAVE_EEPROM=y
CONFIG_I2C_SLAVE_TESTUNIT=y
# CONFIG_I2C_DEBUG_CORE is not set
CONFIG_I2C_DEBUG_ALGO=y
# CONFIG_I2C_DEBUG_BUS is not set
# end of I2C support

CONFIG_I3C=y
# CONFIG_CDNS_I3C_MASTER is not set
CONFIG_DW_I3C_MASTER=y
CONFIG_SVC_I3C_MASTER=y
CONFIG_MIPI_I3C_HCI=y
CONFIG_SPI=y
CONFIG_SPI_MASTER=y
CONFIG_SPI_MEM=y

#
# SPI Master Controller Drivers
#
# CONFIG_SPI_ALTERA is not set
CONFIG_SPI_ALTERA_CORE=y
CONFIG_SPI_AR934X=y
CONFIG_SPI_ATH79=y
# CONFIG_SPI_ARMADA_3700 is not set
CONFIG_SPI_ASPEED_SMC=y
CONFIG_SPI_ATMEL=y
# CONFIG_SPI_AT91_USART is not set
# CONFIG_SPI_ATMEL_QUADSPI is not set
CONFIG_SPI_AXI_SPI_ENGINE=y
CONFIG_SPI_BCM2835=y
CONFIG_SPI_BCM2835AUX=y
CONFIG_SPI_BCM63XX=y
CONFIG_SPI_BCM63XX_HSSPI=y
CONFIG_SPI_BCM_QSPI=y
CONFIG_SPI_BITBANG=y
CONFIG_SPI_BUTTERFLY=y
CONFIG_SPI_CADENCE=y
CONFIG_SPI_CADENCE_QUADSPI=y
# CONFIG_SPI_CADENCE_XSPI is not set
CONFIG_SPI_CLPS711X=y
CONFIG_SPI_COLDFIRE_QSPI=y
# CONFIG_SPI_DESIGNWARE is not set
# CONFIG_SPI_EP93XX is not set
CONFIG_SPI_FSI=y
CONFIG_SPI_FSL_LPSPI=y
CONFIG_SPI_FSL_QUADSPI=y
# CONFIG_SPI_GXP is not set
# CONFIG_SPI_HISI_KUNPENG is not set
# CONFIG_SPI_HISI_SFC_V3XX is not set
# CONFIG_SPI_NXP_FLEXSPI is not set
# CONFIG_SPI_GPIO is not set
CONFIG_SPI_IMG_SPFI=y
# CONFIG_SPI_IMX is not set
# CONFIG_SPI_INGENIC is not set
CONFIG_SPI_INTEL=y
CONFIG_SPI_INTEL_PLATFORM=y
# CONFIG_SPI_JCORE is not set
CONFIG_SPI_LM70_LLP=y
# CONFIG_SPI_LP8841_RTC is not set
CONFIG_SPI_FSL_LIB=y
CONFIG_SPI_FSL_SPI=y
CONFIG_SPI_FSL_DSPI=y
CONFIG_SPI_MESON_SPIFC=y
# CONFIG_SPI_MICROCHIP_CORE is not set
# CONFIG_SPI_MICROCHIP_CORE_QSPI is not set
CONFIG_SPI_MT65XX=y
# CONFIG_SPI_MT7621 is not set
CONFIG_SPI_MTK_NOR=y
CONFIG_SPI_NPCM_FIU=y
# CONFIG_SPI_NPCM_PSPI is not set
# CONFIG_SPI_LANTIQ_SSC is not set
CONFIG_SPI_OC_TINY=y
CONFIG_SPI_OMAP24XX=y
# CONFIG_SPI_TI_QSPI is not set
# CONFIG_SPI_OMAP_100K is not set
CONFIG_SPI_ORION=y
# CONFIG_SPI_PIC32 is not set
CONFIG_SPI_PIC32_SQI=y
CONFIG_SPI_PXA2XX=y
CONFIG_SPI_ROCKCHIP=y
CONFIG_SPI_ROCKCHIP_SFC=y
CONFIG_SPI_RPCIF=y
CONFIG_SPI_RSPI=y
# CONFIG_SPI_QUP is not set
# CONFIG_SPI_QCOM_GENI is not set
CONFIG_SPI_S3C64XX=y
CONFIG_SPI_SC18IS602=y
# CONFIG_SPI_SH_MSIOF is not set
CONFIG_SPI_SH=y
CONFIG_SPI_SH_HSPI=y
# CONFIG_SPI_SIFIVE is not set
CONFIG_SPI_SLAVE_MT27XX=y
CONFIG_SPI_SPRD=y
CONFIG_SPI_SPRD_ADI=y
# CONFIG_SPI_STM32 is not set
CONFIG_SPI_STM32_QSPI=y
# CONFIG_SPI_ST_SSC4 is not set
CONFIG_SPI_SUN4I=y
CONFIG_SPI_SUN6I=y
# CONFIG_SPI_SUNPLUS_SP7021 is not set
# CONFIG_SPI_SYNQUACER is not set
CONFIG_SPI_MXIC=y
CONFIG_SPI_TEGRA210_QUAD=y
# CONFIG_SPI_TEGRA114 is not set
CONFIG_SPI_TEGRA20_SFLASH=y
CONFIG_SPI_TEGRA20_SLINK=y
CONFIG_SPI_UNIPHIER=y
# CONFIG_SPI_XCOMM is not set
CONFIG_SPI_XILINX=y
CONFIG_SPI_XLP=y
CONFIG_SPI_XTENSA_XTFPGA=y
# CONFIG_SPI_ZYNQ_QSPI is not set
# CONFIG_SPI_ZYNQMP_GQSPI is not set
CONFIG_SPI_AMD=y

#
# SPI Multiplexer support
#
CONFIG_SPI_MUX=y

#
# SPI Protocol Masters
#
CONFIG_SPI_SPIDEV=y
# CONFIG_SPI_TLE62X0 is not set
CONFIG_SPI_SLAVE=y
# CONFIG_SPI_SLAVE_TIME is not set
CONFIG_SPI_SLAVE_SYSTEM_CONTROL=y
CONFIG_SPI_DYNAMIC=y
CONFIG_SPMI=y
# CONFIG_SPMI_HISI3670 is not set
CONFIG_SPMI_MSM_PMIC_ARB=y
CONFIG_SPMI_MTK_PMIF=y
# CONFIG_HSI is not set
CONFIG_PPS=y
# CONFIG_PPS_DEBUG is not set

#
# PPS clients support
#
CONFIG_PPS_CLIENT_KTIMER=y
CONFIG_PPS_CLIENT_LDISC=y
# CONFIG_PPS_CLIENT_PARPORT is not set
# CONFIG_PPS_CLIENT_GPIO is not set

#
# PPS generators support
#

#
# PTP clock support
#
CONFIG_PTP_1588_CLOCK=y
CONFIG_PTP_1588_CLOCK_OPTIONAL=y
# CONFIG_PTP_1588_CLOCK_DTE is not set
# CONFIG_PTP_1588_CLOCK_QORIQ is not set
# CONFIG_DP83640_PHY is not set
CONFIG_PTP_1588_CLOCK_INES=y
CONFIG_PTP_1588_CLOCK_IDT82P33=y
CONFIG_PTP_1588_CLOCK_IDTCM=y
# end of PTP clock support

CONFIG_PINCTRL=y
CONFIG_GENERIC_PINCTRL_GROUPS=y
CONFIG_PINMUX=y
CONFIG_GENERIC_PINMUX_FUNCTIONS=y
CONFIG_PINCONF=y
CONFIG_GENERIC_PINCONF=y
# CONFIG_PINCTRL_AMD is not set
CONFIG_PINCTRL_AS3722=y
CONFIG_PINCTRL_AT91PIO4=y
CONFIG_PINCTRL_AXP209=y
CONFIG_PINCTRL_BM1880=y
# CONFIG_PINCTRL_CY8C95X0 is not set
CONFIG_PINCTRL_DA850_PUPD=y
CONFIG_PINCTRL_DA9062=y
CONFIG_PINCTRL_EQUILIBRIUM=y
CONFIG_PINCTRL_INGENIC=y
# CONFIG_PINCTRL_LPC18XX is not set
CONFIG_PINCTRL_MAX77620=y
CONFIG_PINCTRL_MCP23S08_I2C=y
CONFIG_PINCTRL_MCP23S08_SPI=y
CONFIG_PINCTRL_MCP23S08=y
# CONFIG_PINCTRL_MICROCHIP_SGPIO is not set
CONFIG_PINCTRL_OCELOT=y
# CONFIG_PINCTRL_PALMAS is not set
# CONFIG_PINCTRL_PISTACHIO is not set
CONFIG_PINCTRL_ROCKCHIP=y
# CONFIG_PINCTRL_SINGLE is not set
# CONFIG_PINCTRL_STMFX is not set
CONFIG_PINCTRL_SX150X=y
# CONFIG_PINCTRL_OWL is not set
CONFIG_PINCTRL_ASPEED=y
# CONFIG_PINCTRL_ASPEED_G4 is not set
CONFIG_PINCTRL_ASPEED_G5=y
# CONFIG_PINCTRL_ASPEED_G6 is not set
CONFIG_PINCTRL_BCM281XX=y
# CONFIG_PINCTRL_BCM2835 is not set
# CONFIG_PINCTRL_BCM4908 is not set
CONFIG_PINCTRL_BCM63XX=y
CONFIG_PINCTRL_BCM6318=y
CONFIG_PINCTRL_BCM6328=y
# CONFIG_PINCTRL_BCM6358 is not set
# CONFIG_PINCTRL_BCM6362 is not set
# CONFIG_PINCTRL_BCM6368 is not set
# CONFIG_PINCTRL_BCM63268 is not set
CONFIG_PINCTRL_IPROC_GPIO=y
CONFIG_PINCTRL_CYGNUS_MUX=y
# CONFIG_PINCTRL_NS is not set
CONFIG_PINCTRL_NSP_GPIO=y
# CONFIG_PINCTRL_NS2_MUX is not set
CONFIG_PINCTRL_NSP_MUX=y
CONFIG_PINCTRL_BERLIN=y
CONFIG_PINCTRL_AS370=y
CONFIG_PINCTRL_BERLIN_BG4CT=y
CONFIG_PINCTRL_MADERA=y
CONFIG_PINCTRL_CS47L35=y
CONFIG_PINCTRL_CS47L85=y

#
# Intel pinctrl drivers
#
# end of Intel pinctrl drivers

#
# MediaTek pinctrl drivers
#
CONFIG_EINT_MTK=y
CONFIG_PINCTRL_MTK=y
CONFIG_PINCTRL_MTK_V2=y
CONFIG_PINCTRL_MTK_MOORE=y
CONFIG_PINCTRL_MTK_PARIS=y
# CONFIG_PINCTRL_MT2701 is not set
CONFIG_PINCTRL_MT7623=y
# CONFIG_PINCTRL_MT7629 is not set
# CONFIG_PINCTRL_MT8135 is not set
# CONFIG_PINCTRL_MT8127 is not set
CONFIG_PINCTRL_MT2712=y
# CONFIG_PINCTRL_MT6765 is not set
CONFIG_PINCTRL_MT6779=y
# CONFIG_PINCTRL_MT6795 is not set
# CONFIG_PINCTRL_MT6797 is not set
# CONFIG_PINCTRL_MT7622 is not set
# CONFIG_PINCTRL_MT7986 is not set
CONFIG_PINCTRL_MT8167=y
CONFIG_PINCTRL_MT8173=y
# CONFIG_PINCTRL_MT8183 is not set
# CONFIG_PINCTRL_MT8186 is not set
# CONFIG_PINCTRL_MT8188 is not set
CONFIG_PINCTRL_MT8192=y
CONFIG_PINCTRL_MT8195=y
CONFIG_PINCTRL_MT8365=y
CONFIG_PINCTRL_MT8516=y
CONFIG_PINCTRL_MT6397=y
# end of MediaTek pinctrl drivers

CONFIG_PINCTRL_MESON=y
# CONFIG_PINCTRL_WPCM450 is not set
CONFIG_PINCTRL_NPCM7XX=y
CONFIG_PINCTRL_PXA=y
CONFIG_PINCTRL_PXA25X=y
# CONFIG_PINCTRL_PXA27X is not set
CONFIG_PINCTRL_MSM=y
# CONFIG_PINCTRL_APQ8064 is not set
CONFIG_PINCTRL_APQ8084=y
CONFIG_PINCTRL_IPQ4019=y
# CONFIG_PINCTRL_IPQ8064 is not set
CONFIG_PINCTRL_IPQ8074=y
# CONFIG_PINCTRL_IPQ6018 is not set
CONFIG_PINCTRL_MSM8226=y
CONFIG_PINCTRL_MSM8660=y
# CONFIG_PINCTRL_MSM8960 is not set
CONFIG_PINCTRL_MDM9607=y
CONFIG_PINCTRL_MDM9615=y
CONFIG_PINCTRL_MSM8X74=y
# CONFIG_PINCTRL_MSM8909 is not set
CONFIG_PINCTRL_MSM8916=y
CONFIG_PINCTRL_MSM8953=y
# CONFIG_PINCTRL_MSM8976 is not set
CONFIG_PINCTRL_MSM8994=y
CONFIG_PINCTRL_MSM8996=y
CONFIG_PINCTRL_MSM8998=y
# CONFIG_PINCTRL_QCM2290 is not set
CONFIG_PINCTRL_QCS404=y
CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
CONFIG_PINCTRL_QCOM_SSBI_PMIC=y
# CONFIG_PINCTRL_SC7180 is not set
CONFIG_PINCTRL_SC7280=y
CONFIG_PINCTRL_SC7280_LPASS_LPI=y
CONFIG_PINCTRL_SC8180X=y
# CONFIG_PINCTRL_SC8280XP is not set
# CONFIG_PINCTRL_SDM660 is not set
CONFIG_PINCTRL_SDM845=y
# CONFIG_PINCTRL_SDX55 is not set
CONFIG_PINCTRL_SM6115=y
CONFIG_PINCTRL_SM6125=y
# CONFIG_PINCTRL_SM6350 is not set
# CONFIG_PINCTRL_SM6375 is not set
# CONFIG_PINCTRL_SDX65 is not set
CONFIG_PINCTRL_SM8150=y
CONFIG_PINCTRL_SM8250=y
CONFIG_PINCTRL_SM8250_LPASS_LPI=y
# CONFIG_PINCTRL_SM8350 is not set
# CONFIG_PINCTRL_SM8450 is not set
# CONFIG_PINCTRL_SM8450_LPASS_LPI is not set
# CONFIG_PINCTRL_SC8280XP_LPASS_LPI is not set
CONFIG_PINCTRL_LPASS_LPI=y

#
# Renesas pinctrl drivers
#
CONFIG_PINCTRL_RENESAS=y
CONFIG_PINCTRL_SH_PFC=y
CONFIG_PINCTRL_SH_PFC_GPIO=y
CONFIG_PINCTRL_SH_FUNC_GPIO=y
# CONFIG_PINCTRL_PFC_EMEV2 is not set
CONFIG_PINCTRL_PFC_R8A77995=y
CONFIG_PINCTRL_PFC_R8A7794=y
CONFIG_PINCTRL_PFC_R8A77990=y
# CONFIG_PINCTRL_PFC_R8A7779 is not set
CONFIG_PINCTRL_PFC_R8A7790=y
# CONFIG_PINCTRL_PFC_R8A77950 is not set
# CONFIG_PINCTRL_PFC_R8A77951 is not set
CONFIG_PINCTRL_PFC_R8A7778=y
# CONFIG_PINCTRL_PFC_R8A7793 is not set
# CONFIG_PINCTRL_PFC_R8A7791 is not set
CONFIG_PINCTRL_PFC_R8A77965=y
# CONFIG_PINCTRL_PFC_R8A77960 is not set
# CONFIG_PINCTRL_PFC_R8A77961 is not set
# CONFIG_PINCTRL_PFC_R8A779F0 is not set
CONFIG_PINCTRL_PFC_R8A7792=y
CONFIG_PINCTRL_PFC_R8A77980=y
CONFIG_PINCTRL_PFC_R8A77970=y
CONFIG_PINCTRL_PFC_R8A779A0=y
# CONFIG_PINCTRL_PFC_R8A779G0 is not set
CONFIG_PINCTRL_PFC_R8A7740=y
# CONFIG_PINCTRL_PFC_R8A73A4 is not set
CONFIG_PINCTRL_RZA1=y
# CONFIG_PINCTRL_RZA2 is not set
CONFIG_PINCTRL_RZG2L=y
# CONFIG_PINCTRL_PFC_R8A77470 is not set
# CONFIG_PINCTRL_PFC_R8A7745 is not set
CONFIG_PINCTRL_PFC_R8A7742=y
CONFIG_PINCTRL_PFC_R8A7743=y
# CONFIG_PINCTRL_PFC_R8A7744 is not set
# CONFIG_PINCTRL_PFC_R8A774C0 is not set
CONFIG_PINCTRL_PFC_R8A774E1=y
# CONFIG_PINCTRL_PFC_R8A774A1 is not set
CONFIG_PINCTRL_PFC_R8A774B1=y
# CONFIG_PINCTRL_RZN1 is not set
# CONFIG_PINCTRL_RZV2M is not set
# CONFIG_PINCTRL_PFC_SH7203 is not set
# CONFIG_PINCTRL_PFC_SH7264 is not set
CONFIG_PINCTRL_PFC_SH7269=y
# CONFIG_PINCTRL_PFC_SH7720 is not set
CONFIG_PINCTRL_PFC_SH7722=y
# CONFIG_PINCTRL_PFC_SH7734 is not set
# CONFIG_PINCTRL_PFC_SH7757 is not set
CONFIG_PINCTRL_PFC_SH7785=y
CONFIG_PINCTRL_PFC_SH7786=y
CONFIG_PINCTRL_PFC_SH73A0=y
CONFIG_PINCTRL_PFC_SH7723=y
# CONFIG_PINCTRL_PFC_SH7724 is not set
# CONFIG_PINCTRL_PFC_SHX3 is not set
# end of Renesas pinctrl drivers

CONFIG_PINCTRL_SAMSUNG=y
CONFIG_PINCTRL_EXYNOS=y
CONFIG_PINCTRL_EXYNOS_ARM=y
CONFIG_PINCTRL_EXYNOS_ARM64=y
# CONFIG_PINCTRL_S3C24XX is not set
CONFIG_PINCTRL_S3C64XX=y
# CONFIG_PINCTRL_SPRD_SC9860 is not set
# CONFIG_PINCTRL_STARFIVE_JH7100 is not set
CONFIG_PINCTRL_STM32=y
# CONFIG_PINCTRL_STM32F429 is not set
CONFIG_PINCTRL_STM32F469=y
CONFIG_PINCTRL_STM32F746=y
# CONFIG_PINCTRL_STM32F769 is not set
# CONFIG_PINCTRL_STM32H743 is not set
# CONFIG_PINCTRL_STM32MP135 is not set
# CONFIG_PINCTRL_STM32MP157 is not set
CONFIG_PINCTRL_TI_IODELAY=y
CONFIG_PINCTRL_UNIPHIER=y
CONFIG_PINCTRL_UNIPHIER_LD4=y
# CONFIG_PINCTRL_UNIPHIER_PRO4 is not set
CONFIG_PINCTRL_UNIPHIER_SLD8=y
CONFIG_PINCTRL_UNIPHIER_PRO5=y
CONFIG_PINCTRL_UNIPHIER_PXS2=y
# CONFIG_PINCTRL_UNIPHIER_LD6B is not set
# CONFIG_PINCTRL_UNIPHIER_LD11 is not set
# CONFIG_PINCTRL_UNIPHIER_LD20 is not set
# CONFIG_PINCTRL_UNIPHIER_PXS3 is not set
# CONFIG_PINCTRL_UNIPHIER_NX1 is not set
CONFIG_PINCTRL_VISCONTI=y
CONFIG_PINCTRL_TMPV7700=y
CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
CONFIG_GPIOLIB=y
CONFIG_GPIOLIB_FASTPATH_LIMIT=512
CONFIG_OF_GPIO=y
CONFIG_GPIOLIB_IRQCHIP=y
CONFIG_GPIO_CDEV=y
# CONFIG_GPIO_CDEV_V1 is not set
CONFIG_GPIO_GENERIC=y
CONFIG_GPIO_REGMAP=y
CONFIG_GPIO_MAX730X=y

#
# Memory mapped GPIO drivers
#
CONFIG_GPIO_74XX_MMIO=y
CONFIG_GPIO_ALTERA=y
# CONFIG_GPIO_ASPEED is not set
CONFIG_GPIO_ASPEED_SGPIO=y
CONFIG_GPIO_ATH79=y
CONFIG_GPIO_RASPBERRYPI_EXP=y
CONFIG_GPIO_BCM_KONA=y
CONFIG_GPIO_BCM_XGS_IPROC=y
# CONFIG_GPIO_BRCMSTB is not set
# CONFIG_GPIO_CADENCE is not set
CONFIG_GPIO_CLPS711X=y
# CONFIG_GPIO_DWAPB is not set
CONFIG_GPIO_EIC_SPRD=y
CONFIG_GPIO_EM=y
# CONFIG_GPIO_FTGPIO010 is not set
# CONFIG_GPIO_GENERIC_PLATFORM is not set
CONFIG_GPIO_GRGPIO=y
# CONFIG_GPIO_HISI is not set
CONFIG_GPIO_HLWD=y
# CONFIG_GPIO_IOP is not set
# CONFIG_GPIO_LOGICVC is not set
CONFIG_GPIO_LPC18XX=y
CONFIG_GPIO_LPC32XX=y
CONFIG_GPIO_MB86S7X=y
# CONFIG_GPIO_MENZ127 is not set
CONFIG_GPIO_MPC8XXX=y
CONFIG_GPIO_MT7621=y
CONFIG_GPIO_MXC=y
CONFIG_GPIO_MXS=y
CONFIG_GPIO_PMIC_EIC_SPRD=y
CONFIG_GPIO_PXA=y
# CONFIG_GPIO_RCAR is not set
# CONFIG_GPIO_RDA is not set
# CONFIG_GPIO_ROCKCHIP is not set
CONFIG_GPIO_SAMA5D2_PIOBU=y
CONFIG_GPIO_SIFIVE=y
# CONFIG_GPIO_SNPS_CREG is not set
# CONFIG_GPIO_SPRD is not set
# CONFIG_GPIO_STP_XWAY is not set
CONFIG_GPIO_SYSCON=y
# CONFIG_GPIO_TEGRA is not set
CONFIG_GPIO_TEGRA186=y
# CONFIG_GPIO_TS4800 is not set
CONFIG_GPIO_UNIPHIER=y
CONFIG_GPIO_VISCONTI=y
# CONFIG_GPIO_WCD934X is not set
CONFIG_GPIO_XGENE_SB=y
CONFIG_GPIO_XILINX=y
CONFIG_GPIO_XLP=y
CONFIG_GPIO_AMD_FCH=y
CONFIG_GPIO_IDT3243X=y
# end of Memory mapped GPIO drivers

#
# I2C GPIO expanders
#
CONFIG_GPIO_ADNP=y
# CONFIG_GPIO_GW_PLD is not set
CONFIG_GPIO_MAX7300=y
CONFIG_GPIO_MAX732X=y
CONFIG_GPIO_MAX732X_IRQ=y
# CONFIG_GPIO_PCA953X is not set
CONFIG_GPIO_PCA9570=y
CONFIG_GPIO_PCF857X=y
CONFIG_GPIO_TPIC2810=y
# CONFIG_GPIO_TS4900 is not set
# end of I2C GPIO expanders

#
# MFD GPIO expanders
#
CONFIG_GPIO_ARIZONA=y
CONFIG_GPIO_BD71815=y
# CONFIG_GPIO_BD71828 is not set
CONFIG_GPIO_BD9571MWV=y
CONFIG_GPIO_DA9052=y
CONFIG_GPIO_DA9055=y
CONFIG_GPIO_LP873X=y
CONFIG_GPIO_MADERA=y
CONFIG_GPIO_MAX77620=y
# CONFIG_GPIO_PALMAS is not set
CONFIG_GPIO_SL28CPLD=y
CONFIG_GPIO_TPS65086=y
CONFIG_GPIO_TPS65218=y
CONFIG_GPIO_TPS65912=y
CONFIG_GPIO_TWL4030=y
# CONFIG_GPIO_WM8994 is not set
# end of MFD GPIO expanders

#
# SPI GPIO expanders
#
CONFIG_GPIO_74X164=y
CONFIG_GPIO_MAX3191X=y
CONFIG_GPIO_MAX7301=y
CONFIG_GPIO_MC33880=y
CONFIG_GPIO_PISOSR=y
# CONFIG_GPIO_XRA1403 is not set
# CONFIG_GPIO_MOXTET is not set
# end of SPI GPIO expanders

#
# USB GPIO expanders
#
# end of USB GPIO expanders

#
# Virtual GPIO drivers
#
CONFIG_GPIO_AGGREGATOR=y
CONFIG_GPIO_MOCKUP=y
CONFIG_GPIO_VIRTIO=y
# CONFIG_GPIO_SIM is not set
# end of Virtual GPIO drivers

CONFIG_W1=y
# CONFIG_W1_CON is not set

#
# 1-wire Bus Masters
#
CONFIG_W1_MASTER_DS2490=y
CONFIG_W1_MASTER_DS2482=y
CONFIG_W1_MASTER_MXC=y
CONFIG_W1_MASTER_DS1WM=y
CONFIG_W1_MASTER_GPIO=y
CONFIG_W1_MASTER_SGI=y
# end of 1-wire Bus Masters

#
# 1-wire Slaves
#
CONFIG_W1_SLAVE_THERM=y
# CONFIG_W1_SLAVE_SMEM is not set
# CONFIG_W1_SLAVE_DS2405 is not set
# CONFIG_W1_SLAVE_DS2408 is not set
# CONFIG_W1_SLAVE_DS2413 is not set
CONFIG_W1_SLAVE_DS2406=y
CONFIG_W1_SLAVE_DS2423=y
# CONFIG_W1_SLAVE_DS2805 is not set
CONFIG_W1_SLAVE_DS2430=y
CONFIG_W1_SLAVE_DS2431=y
CONFIG_W1_SLAVE_DS2433=y
# CONFIG_W1_SLAVE_DS2433_CRC is not set
CONFIG_W1_SLAVE_DS2438=y
CONFIG_W1_SLAVE_DS250X=y
CONFIG_W1_SLAVE_DS2780=y
CONFIG_W1_SLAVE_DS2781=y
CONFIG_W1_SLAVE_DS28E04=y
CONFIG_W1_SLAVE_DS28E17=y
# end of 1-wire Slaves

# CONFIG_POWER_RESET is not set
CONFIG_POWER_SUPPLY=y
CONFIG_POWER_SUPPLY_DEBUG=y
CONFIG_PDA_POWER=y
CONFIG_GENERIC_ADC_BATTERY=y
# CONFIG_IP5XXX_POWER is not set
# CONFIG_TEST_POWER is not set
# CONFIG_BATTERY_88PM860X is not set
# CONFIG_CHARGER_ADP5061 is not set
CONFIG_BATTERY_ACT8945A=y
CONFIG_BATTERY_CW2015=y
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_BATTERY_DS2780 is not set
CONFIG_BATTERY_DS2781=y
CONFIG_BATTERY_DS2782=y
# CONFIG_BATTERY_LEGO_EV3 is not set
# CONFIG_BATTERY_SAMSUNG_SDI is not set
CONFIG_BATTERY_SBS=y
CONFIG_CHARGER_SBS=y
CONFIG_MANAGER_SBS=y
# CONFIG_BATTERY_BQ27XXX is not set
CONFIG_BATTERY_DA9052=y
CONFIG_AXP20X_POWER=y
CONFIG_BATTERY_MAX17040=y
CONFIG_BATTERY_MAX17042=y
CONFIG_BATTERY_MAX1721X=y
CONFIG_BATTERY_TWL4030_MADC=y
CONFIG_BATTERY_RX51=y
CONFIG_CHARGER_ISP1704=y
# CONFIG_CHARGER_MAX8903 is not set
CONFIG_CHARGER_TWL4030=y
CONFIG_CHARGER_LP8727=y
CONFIG_CHARGER_GPIO=y
CONFIG_CHARGER_MANAGER=y
CONFIG_CHARGER_LT3651=y
CONFIG_CHARGER_LTC4162L=y
# CONFIG_CHARGER_MAX14577 is not set
CONFIG_CHARGER_DETECTOR_MAX14656=y
CONFIG_CHARGER_MAX77693=y
# CONFIG_CHARGER_MAX77976 is not set
CONFIG_CHARGER_MAX8997=y
# CONFIG_CHARGER_MAX8998 is not set
CONFIG_CHARGER_MP2629=y
# CONFIG_CHARGER_MT6360 is not set
# CONFIG_CHARGER_QCOM_SMBB is not set
# CONFIG_CHARGER_BQ2415X is not set
CONFIG_CHARGER_BQ24190=y
CONFIG_CHARGER_BQ24257=y
CONFIG_CHARGER_BQ24735=y
CONFIG_CHARGER_BQ2515X=y
# CONFIG_CHARGER_BQ25890 is not set
# CONFIG_CHARGER_BQ25980 is not set
CONFIG_CHARGER_BQ256XX=y
# CONFIG_CHARGER_SMB347 is not set
CONFIG_BATTERY_GAUGE_LTC2941=y
CONFIG_BATTERY_GOLDFISH=y
# CONFIG_BATTERY_RT5033 is not set
CONFIG_CHARGER_RT9455=y
CONFIG_CHARGER_SC2731=y
CONFIG_FUEL_GAUGE_SC27XX=y
CONFIG_CHARGER_UCS1002=y
CONFIG_CHARGER_BD99954=y
# CONFIG_BATTERY_ACER_A500 is not set
# CONFIG_BATTERY_UG3105 is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_CORE=y
CONFIG_WATCHDOG_NOWAYOUT=y
# CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is not set
CONFIG_WATCHDOG_OPEN_TIMEOUT=0
# CONFIG_WATCHDOG_SYSFS is not set
CONFIG_WATCHDOG_HRTIMER_PRETIMEOUT=y

#
# Watchdog Pretimeout Governors
#
# CONFIG_WATCHDOG_PRETIMEOUT_GOV is not set

#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=y
CONFIG_BD957XMUF_WATCHDOG=y
CONFIG_DA9052_WATCHDOG=y
CONFIG_DA9055_WATCHDOG=y
# CONFIG_DA9063_WATCHDOG is not set
CONFIG_DA9062_WATCHDOG=y
# CONFIG_GPIO_WATCHDOG is not set
# CONFIG_MENF21BMC_WATCHDOG is not set
# CONFIG_MENZ069_WATCHDOG is not set
# CONFIG_XILINX_WATCHDOG is not set
# CONFIG_ZIIRAVE_WATCHDOG is not set
CONFIG_RAVE_SP_WATCHDOG=y
CONFIG_SL28CPLD_WATCHDOG=y
CONFIG_ARMADA_37XX_WATCHDOG=y
CONFIG_ASM9260_WATCHDOG=y
CONFIG_AT91RM9200_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
CONFIG_SAMA5D4_WATCHDOG=y
CONFIG_CADENCE_WATCHDOG=y
CONFIG_FTWDT010_WATCHDOG=y
# CONFIG_S3C2410_WATCHDOG is not set
CONFIG_DW_WATCHDOG=y
CONFIG_EP93XX_WATCHDOG=y
# CONFIG_OMAP_WATCHDOG is not set
# CONFIG_PNX4008_WATCHDOG is not set
CONFIG_DAVINCI_WATCHDOG=y
# CONFIG_K3_RTI_WATCHDOG is not set
# CONFIG_RN5T618_WATCHDOG is not set
CONFIG_SUNXI_WATCHDOG=y
# CONFIG_NPCM7XX_WATCHDOG is not set
CONFIG_TWL4030_WATCHDOG=y
# CONFIG_STMP3XXX_RTC_WATCHDOG is not set
# CONFIG_TS4800_WATCHDOG is not set
CONFIG_TS72XX_WATCHDOG=y
CONFIG_MAX63XX_WATCHDOG=y
# CONFIG_MAX77620_WATCHDOG is not set
# CONFIG_IMX2_WDT is not set
CONFIG_IMX7ULP_WDT=y
CONFIG_RETU_WATCHDOG=y
# CONFIG_MOXART_WDT is not set
CONFIG_ST_LPC_WATCHDOG=y
CONFIG_TEGRA_WATCHDOG=y
# CONFIG_QCOM_WDT is not set
CONFIG_MESON_GXBB_WATCHDOG=y
CONFIG_MESON_WATCHDOG=y
CONFIG_MEDIATEK_WATCHDOG=y
# CONFIG_DIGICOLOR_WATCHDOG is not set
CONFIG_LPC18XX_WATCHDOG=y
CONFIG_RENESAS_WDT=y
CONFIG_RENESAS_RZAWDT=y
# CONFIG_RENESAS_RZN1WDT is not set
# CONFIG_RENESAS_RZG2LWDT is not set
# CONFIG_ASPEED_WATCHDOG is not set
CONFIG_STPMIC1_WATCHDOG=y
CONFIG_UNIPHIER_WATCHDOG=y
CONFIG_RTD119X_WATCHDOG=y
# CONFIG_SPRD_WATCHDOG is not set
# CONFIG_PM8916_WATCHDOG is not set
CONFIG_VISCONTI_WATCHDOG=y
# CONFIG_MSC313E_WATCHDOG is not set
# CONFIG_APPLE_WATCHDOG is not set
# CONFIG_SUNPLUS_WATCHDOG is not set
# CONFIG_SC520_WDT is not set
CONFIG_BCM47XX_WDT=y
CONFIG_BCM2835_WDT=y
CONFIG_BCM_KONA_WDT=y
CONFIG_BCM_KONA_WDT_DEBUG=y
# CONFIG_BCM7038_WDT is not set
CONFIG_IMGPDC_WDT=y
# CONFIG_MPC5200_WDT is not set
CONFIG_MEN_A21_WDT=y
CONFIG_UML_WATCHDOG=y

#
# USB-based Watchdog Cards
#
CONFIG_USBPCWATCHDOG=y
CONFIG_SSB_POSSIBLE=y
CONFIG_SSB=y
CONFIG_SSB_PCMCIAHOST_POSSIBLE=y
# CONFIG_SSB_PCMCIAHOST is not set
CONFIG_SSB_SDIOHOST_POSSIBLE=y
CONFIG_SSB_SDIOHOST=y
# CONFIG_SSB_HOST_SOC is not set
CONFIG_SSB_DRIVER_GPIO=y
CONFIG_BCMA_POSSIBLE=y
CONFIG_BCMA=y
CONFIG_BCMA_HOST_SOC=y
# CONFIG_BCMA_DRIVER_MIPS is not set
# CONFIG_BCMA_SFLASH is not set
CONFIG_BCMA_DRIVER_GMAC_CMN=y
CONFIG_BCMA_DRIVER_GPIO=y
# CONFIG_BCMA_DEBUG is not set

#
# Multifunction device drivers
#
CONFIG_MFD_CORE=y
CONFIG_MFD_ACT8945A=y
# CONFIG_MFD_SUN4I_GPADC is not set
# CONFIG_MFD_AS3711 is not set
CONFIG_MFD_AS3722=y
# CONFIG_PMIC_ADP5520 is not set
CONFIG_MFD_AAT2870_CORE=y
CONFIG_MFD_AT91_USART=y
CONFIG_MFD_ATMEL_FLEXCOM=y
# CONFIG_MFD_ATMEL_HLCDC is not set
CONFIG_MFD_ATMEL_SMC=y
CONFIG_MFD_BCM590XX=y
CONFIG_MFD_BD9571MWV=y
CONFIG_MFD_AXP20X=y
CONFIG_MFD_AXP20X_I2C=y
# CONFIG_MFD_CROS_EC_DEV is not set
CONFIG_MFD_MADERA=y
CONFIG_MFD_MADERA_I2C=y
CONFIG_MFD_MADERA_SPI=y
# CONFIG_MFD_CS47L15 is not set
CONFIG_MFD_CS47L35=y
CONFIG_MFD_CS47L85=y
# CONFIG_MFD_CS47L90 is not set
# CONFIG_MFD_CS47L92 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_PMIC_DA903X is not set
CONFIG_PMIC_DA9052=y
CONFIG_MFD_DA9052_SPI=y
# CONFIG_MFD_DA9052_I2C is not set
CONFIG_MFD_DA9055=y
CONFIG_MFD_DA9062=y
CONFIG_MFD_DA9063=y
# CONFIG_MFD_DA9150 is not set
# CONFIG_MFD_DLN2 is not set
# CONFIG_MFD_ENE_KB3930 is not set
CONFIG_MFD_EXYNOS_LPASS=y
CONFIG_MFD_GATEWORKS_GSC=y
CONFIG_MFD_MC13XXX=y
CONFIG_MFD_MC13XXX_SPI=y
# CONFIG_MFD_MC13XXX_I2C is not set
CONFIG_MFD_MP2629=y
CONFIG_MFD_MXS_LRADC=y
# CONFIG_MFD_MX25_TSADC is not set
CONFIG_MFD_HI6421_PMIC=y
CONFIG_MFD_HI6421_SPMI=y
# CONFIG_MFD_HI655X_PMIC is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_HTC_I2CPLD is not set
CONFIG_MFD_IQS62X=y
# CONFIG_MFD_KEMPLD is not set
CONFIG_MFD_88PM800=y
CONFIG_MFD_88PM805=y
CONFIG_MFD_88PM860X=y
CONFIG_MFD_MAX14577=y
CONFIG_MFD_MAX77620=y
# CONFIG_MFD_MAX77650 is not set
CONFIG_MFD_MAX77686=y
CONFIG_MFD_MAX77693=y
# CONFIG_MFD_MAX77714 is not set
CONFIG_MFD_MAX77843=y
# CONFIG_MFD_MAX8907 is not set
# CONFIG_MFD_MAX8925 is not set
CONFIG_MFD_MAX8997=y
CONFIG_MFD_MAX8998=y
CONFIG_MFD_MT6360=y
# CONFIG_MFD_MT6370 is not set
CONFIG_MFD_MT6397=y
CONFIG_MFD_MENF21BMC=y
# CONFIG_MFD_OCELOT is not set
CONFIG_EZX_PCAP=y
# CONFIG_MFD_CPCAP is not set
# CONFIG_MFD_VIPERBOARD is not set
CONFIG_MFD_NTXEC=y
CONFIG_MFD_RETU=y
# CONFIG_MFD_PCF50633 is not set
# CONFIG_MFD_PM8XXX is not set
CONFIG_MFD_SPMI_PMIC=y
# CONFIG_MFD_SY7636A is not set
CONFIG_MFD_RT4831=y
CONFIG_MFD_RT5033=y
# CONFIG_MFD_RT5120 is not set
# CONFIG_MFD_RC5T583 is not set
# CONFIG_MFD_RK808 is not set
# CONFIG_MFD_RN5T618 is not set
CONFIG_MFD_SEC_CORE=y
CONFIG_MFD_SI476X_CORE=y
# CONFIG_MFD_SL28CPLD is not set
CONFIG_MFD_SM501=y
CONFIG_MFD_SM501_GPIO=y
# CONFIG_MFD_SKY81452 is not set
CONFIG_MFD_SC27XX_PMIC=y
# CONFIG_ABX500_CORE is not set
# CONFIG_MFD_STMPE is not set
# CONFIG_MFD_SUN6I_PRCM is not set
CONFIG_MFD_SYSCON=y
CONFIG_MFD_TI_AM335X_TSCADC=y
# CONFIG_MFD_LP3943 is not set
# CONFIG_MFD_LP8788 is not set
CONFIG_MFD_TI_LMU=y
CONFIG_MFD_PALMAS=y
CONFIG_TPS6105X=y
# CONFIG_TPS65010 is not set
# CONFIG_TPS6507X is not set
CONFIG_MFD_TPS65086=y
# CONFIG_MFD_TPS65090 is not set
# CONFIG_MFD_TPS65217 is not set
CONFIG_MFD_TI_LP873X=y
# CONFIG_MFD_TI_LP87565 is not set
CONFIG_MFD_TPS65218=y
# CONFIG_MFD_TPS6586X is not set
# CONFIG_MFD_TPS65910 is not set
CONFIG_MFD_TPS65912=y
CONFIG_MFD_TPS65912_I2C=y
# CONFIG_MFD_TPS65912_SPI is not set
CONFIG_TWL4030_CORE=y
CONFIG_MFD_TWL4030_AUDIO=y
# CONFIG_TWL6040_CORE is not set
# CONFIG_MFD_WL1273_CORE is not set
CONFIG_MFD_LM3533=y
# CONFIG_MFD_TC3589X is not set
CONFIG_MFD_TQMX86=y
# CONFIG_MFD_LOCHNAGAR is not set
CONFIG_MFD_ARIZONA=y
# CONFIG_MFD_ARIZONA_I2C is not set
CONFIG_MFD_ARIZONA_SPI=y
# CONFIG_MFD_CS47L24 is not set
CONFIG_MFD_WM5102=y
# CONFIG_MFD_WM5110 is not set
CONFIG_MFD_WM8997=y
# CONFIG_MFD_WM8998 is not set
CONFIG_MFD_WM8400=y
# CONFIG_MFD_WM831X_I2C is not set
# CONFIG_MFD_WM831X_SPI is not set
# CONFIG_MFD_WM8350_I2C is not set
CONFIG_MFD_WM8994=y
CONFIG_MFD_STW481X=y
# CONFIG_MFD_ROHM_BD718XX is not set
CONFIG_MFD_ROHM_BD71828=y
CONFIG_MFD_ROHM_BD957XMUF=y
# CONFIG_MFD_STM32_LPTIMER is not set
CONFIG_MFD_STM32_TIMERS=y
CONFIG_MFD_STPMIC1=y
CONFIG_MFD_STMFX=y
CONFIG_MFD_WCD934X=y
CONFIG_MFD_ATC260X=y
CONFIG_MFD_ATC260X_I2C=y
CONFIG_MFD_KHADAS_MCU=y
CONFIG_MFD_ACER_A500_EC=y
CONFIG_MFD_QCOM_PM8008=y
CONFIG_RAVE_SP_CORE=y
# CONFIG_MFD_INTEL_M10_BMC is not set
# CONFIG_MFD_RSMU_I2C is not set
CONFIG_MFD_RSMU_SPI=y
# end of Multifunction device drivers

CONFIG_REGULATOR=y
# CONFIG_REGULATOR_DEBUG is not set
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
CONFIG_REGULATOR_88PG86X=y
CONFIG_REGULATOR_88PM800=y
CONFIG_REGULATOR_88PM8607=y
CONFIG_REGULATOR_ACT8865=y
CONFIG_REGULATOR_ACT8945A=y
CONFIG_REGULATOR_AD5398=y
CONFIG_REGULATOR_ANATOP=y
CONFIG_REGULATOR_AAT2870=y
CONFIG_REGULATOR_ARM_SCMI=y
CONFIG_REGULATOR_AS3722=y
CONFIG_REGULATOR_ATC260X=y
# CONFIG_REGULATOR_AXP20X is not set
CONFIG_REGULATOR_BCM590XX=y
CONFIG_REGULATOR_BD71815=y
CONFIG_REGULATOR_BD71828=y
# CONFIG_REGULATOR_BD9571MWV is not set
CONFIG_REGULATOR_BD957XMUF=y
CONFIG_REGULATOR_CROS_EC=y
CONFIG_REGULATOR_DA9052=y
CONFIG_REGULATOR_DA9055=y
CONFIG_REGULATOR_DA9062=y
CONFIG_REGULATOR_DA9063=y
CONFIG_REGULATOR_DA9121=y
# CONFIG_REGULATOR_DA9210 is not set
# CONFIG_REGULATOR_DA9211 is not set
CONFIG_REGULATOR_FAN53555=y
CONFIG_REGULATOR_FAN53880=y
CONFIG_REGULATOR_GPIO=y
CONFIG_REGULATOR_HI6421=y
CONFIG_REGULATOR_HI6421V530=y
CONFIG_REGULATOR_HI6421V600=y
CONFIG_REGULATOR_ISL9305=y
CONFIG_REGULATOR_ISL6271A=y
CONFIG_REGULATOR_LM363X=y
# CONFIG_REGULATOR_LP3971 is not set
CONFIG_REGULATOR_LP3972=y
# CONFIG_REGULATOR_LP872X is not set
CONFIG_REGULATOR_LP873X=y
CONFIG_REGULATOR_LP8755=y
CONFIG_REGULATOR_LTC3589=y
CONFIG_REGULATOR_LTC3676=y
# CONFIG_REGULATOR_MAX14577 is not set
CONFIG_REGULATOR_MAX1586=y
# CONFIG_REGULATOR_MAX77620 is not set
# CONFIG_REGULATOR_MAX77650 is not set
CONFIG_REGULATOR_MAX8649=y
CONFIG_REGULATOR_MAX8660=y
CONFIG_REGULATOR_MAX8893=y
# CONFIG_REGULATOR_MAX8907 is not set
CONFIG_REGULATOR_MAX8952=y
CONFIG_REGULATOR_MAX8997=y
CONFIG_REGULATOR_MAX8998=y
# CONFIG_REGULATOR_MAX20086 is not set
# CONFIG_REGULATOR_MAX77686 is not set
CONFIG_REGULATOR_MAX77693=y
# CONFIG_REGULATOR_MAX77802 is not set
CONFIG_REGULATOR_MAX77826=y
CONFIG_REGULATOR_MC13XXX_CORE=y
CONFIG_REGULATOR_MC13783=y
CONFIG_REGULATOR_MC13892=y
# CONFIG_REGULATOR_MCP16502 is not set
CONFIG_REGULATOR_MP5416=y
CONFIG_REGULATOR_MP8859=y
CONFIG_REGULATOR_MP886X=y
CONFIG_REGULATOR_MPQ7920=y
# CONFIG_REGULATOR_MT6311 is not set
# CONFIG_REGULATOR_MT6315 is not set
# CONFIG_REGULATOR_MT6323 is not set
# CONFIG_REGULATOR_MT6331 is not set
# CONFIG_REGULATOR_MT6332 is not set
CONFIG_REGULATOR_MT6358=y
# CONFIG_REGULATOR_MT6359 is not set
# CONFIG_REGULATOR_MT6360 is not set
CONFIG_REGULATOR_MT6380=y
# CONFIG_REGULATOR_MT6397 is not set
CONFIG_REGULATOR_PALMAS=y
# CONFIG_REGULATOR_PBIAS is not set
CONFIG_REGULATOR_PCA9450=y
# CONFIG_REGULATOR_PCAP is not set
CONFIG_REGULATOR_PF8X00=y
CONFIG_REGULATOR_PFUZE100=y
# CONFIG_REGULATOR_PV88060 is not set
CONFIG_REGULATOR_PV88080=y
# CONFIG_REGULATOR_PV88090 is not set
# CONFIG_REGULATOR_QCOM_RPMH is not set
CONFIG_REGULATOR_QCOM_SMD_RPM=y
# CONFIG_REGULATOR_QCOM_SPMI is not set
CONFIG_REGULATOR_QCOM_USB_VBUS=y
CONFIG_REGULATOR_RASPBERRYPI_TOUCHSCREEN_ATTINY=y
CONFIG_REGULATOR_ROHM=y
CONFIG_REGULATOR_RT4801=y
# CONFIG_REGULATOR_RT4831 is not set
# CONFIG_REGULATOR_RT5033 is not set
# CONFIG_REGULATOR_RT5190A is not set
# CONFIG_REGULATOR_RT5759 is not set
# CONFIG_REGULATOR_RT6160 is not set
# CONFIG_REGULATOR_RT6245 is not set
CONFIG_REGULATOR_RTQ2134=y
# CONFIG_REGULATOR_RTMV20 is not set
# CONFIG_REGULATOR_RTQ6752 is not set
CONFIG_REGULATOR_S2MPA01=y
CONFIG_REGULATOR_S2MPS11=y
CONFIG_REGULATOR_S5M8767=y
# CONFIG_REGULATOR_SC2731 is not set
CONFIG_REGULATOR_SLG51000=y
CONFIG_REGULATOR_STM32_BOOSTER=y
# CONFIG_REGULATOR_STM32_VREFBUF is not set
# CONFIG_REGULATOR_STM32_PWR is not set
CONFIG_REGULATOR_STPMIC1=y
# CONFIG_REGULATOR_TI_ABB is not set
# CONFIG_REGULATOR_STW481X_VMMC is not set
CONFIG_REGULATOR_SY8106A=y
# CONFIG_REGULATOR_SY8824X is not set
CONFIG_REGULATOR_SY8827N=y
CONFIG_REGULATOR_TPS51632=y
CONFIG_REGULATOR_TPS6105X=y
# CONFIG_REGULATOR_TPS62360 is not set
# CONFIG_REGULATOR_TPS6286X is not set
# CONFIG_REGULATOR_TPS65023 is not set
CONFIG_REGULATOR_TPS6507X=y
CONFIG_REGULATOR_TPS65086=y
# CONFIG_REGULATOR_TPS65132 is not set
CONFIG_REGULATOR_TPS65218=y
CONFIG_REGULATOR_TPS6524X=y
CONFIG_REGULATOR_TPS65912=y
# CONFIG_REGULATOR_TPS68470 is not set
CONFIG_REGULATOR_TWL4030=y
CONFIG_REGULATOR_UNIPHIER=y
CONFIG_REGULATOR_VCTRL=y
CONFIG_REGULATOR_WM8400=y
# CONFIG_REGULATOR_WM8994 is not set
CONFIG_REGULATOR_QCOM_LABIBB=y
CONFIG_RC_CORE=y
CONFIG_LIRC=y
# CONFIG_RC_MAP is not set
# CONFIG_RC_DECODERS is not set
CONFIG_RC_DEVICES=y
# CONFIG_IR_ENE is not set
CONFIG_IR_FINTEK=y
CONFIG_IR_GPIO_CIR=y
CONFIG_IR_GPIO_TX=y
CONFIG_IR_HIX5HD2=y
CONFIG_IR_IGORPLUGUSB=y
CONFIG_IR_IGUANA=y
# CONFIG_IR_IMON is not set
# CONFIG_IR_IMON_RAW is not set
CONFIG_IR_ITE_CIR=y
CONFIG_IR_MCEUSB=y
CONFIG_IR_MESON=y
CONFIG_IR_MESON_TX=y
# CONFIG_IR_MTK is not set
# CONFIG_IR_NUVOTON is not set
CONFIG_IR_REDRAT3=y
# CONFIG_IR_RX51 is not set
# CONFIG_IR_SERIAL is not set
# CONFIG_IR_SPI is not set
CONFIG_IR_STREAMZAP=y
CONFIG_IR_SUNXI=y
# CONFIG_IR_TOY is not set
CONFIG_IR_TTUSBIR=y
CONFIG_IR_WINBOND_CIR=y
CONFIG_RC_ATI_REMOTE=y
CONFIG_RC_LOOPBACK=y
CONFIG_RC_ST=y
CONFIG_RC_XBOX_DVD=y
CONFIG_IR_IMG=y
CONFIG_IR_IMG_RAW=y
CONFIG_IR_IMG_HW=y
CONFIG_IR_IMG_NEC=y
# CONFIG_IR_IMG_JVC is not set
CONFIG_IR_IMG_SONY=y
# CONFIG_IR_IMG_SHARP is not set
# CONFIG_IR_IMG_SANYO is not set
CONFIG_IR_IMG_RC5=y
CONFIG_IR_IMG_RC6=y
CONFIG_CEC_CORE=y
CONFIG_CEC_NOTIFIER=y

#
# CEC support
#
CONFIG_MEDIA_CEC_RC=y
CONFIG_MEDIA_CEC_SUPPORT=y
CONFIG_CEC_CH7322=y
# CONFIG_CEC_CROS_EC is not set
CONFIG_CEC_MESON_AO=y
# CONFIG_CEC_GPIO is not set
# CONFIG_CEC_SAMSUNG_S5P is not set
CONFIG_CEC_STI=y
CONFIG_CEC_STM32=y
# CONFIG_CEC_TEGRA is not set
CONFIG_USB_PULSE8_CEC=y
CONFIG_USB_RAINSHADOW_CEC=y
# end of CEC support

CONFIG_MEDIA_SUPPORT=y
# CONFIG_MEDIA_SUPPORT_FILTER is not set
CONFIG_MEDIA_SUBDRV_AUTOSELECT=y

#
# Media device types
#
CONFIG_MEDIA_CAMERA_SUPPORT=y
CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
CONFIG_MEDIA_RADIO_SUPPORT=y
CONFIG_MEDIA_SDR_SUPPORT=y
CONFIG_MEDIA_PLATFORM_SUPPORT=y
CONFIG_MEDIA_TEST_SUPPORT=y
# end of Media device types

#
# Media core support
#
CONFIG_VIDEO_DEV=y
CONFIG_MEDIA_CONTROLLER=y
CONFIG_DVB_CORE=y
# end of Media core support

#
# Video4Linux options
#
CONFIG_VIDEO_V4L2_I2C=y
CONFIG_VIDEO_V4L2_SUBDEV_API=y
CONFIG_VIDEO_ADV_DEBUG=y
# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
CONFIG_V4L2_H264=y
CONFIG_V4L2_VP9=y
CONFIG_V4L2_MEM2MEM_DEV=y
# CONFIG_V4L2_FLASH_LED_CLASS is not set
CONFIG_V4L2_FWNODE=y
CONFIG_V4L2_ASYNC=y
# end of Video4Linux options

#
# Media controller options
#
# CONFIG_MEDIA_CONTROLLER_DVB is not set
CONFIG_MEDIA_CONTROLLER_REQUEST_API=y
# end of Media controller options

#
# Digital TV options
#
CONFIG_DVB_MMAP=y
CONFIG_DVB_MAX_ADAPTERS=16
# CONFIG_DVB_DYNAMIC_MINORS is not set
CONFIG_DVB_DEMUX_SECTION_LOSS_LOG=y
# CONFIG_DVB_ULE_DEBUG is not set
# end of Digital TV options

#
# Media drivers
#

#
# Media drivers
#
# CONFIG_MEDIA_USB_SUPPORT is not set
CONFIG_RADIO_ADAPTERS=y
# CONFIG_RADIO_SAA7706H is not set
CONFIG_RADIO_SHARK=y
CONFIG_RADIO_SHARK2=y
CONFIG_RADIO_SI4713=y
CONFIG_RADIO_TEA575X=y
CONFIG_RADIO_TEA5764=y
# CONFIG_RADIO_TEA5764_XTAL is not set
# CONFIG_RADIO_TEF6862 is not set
# CONFIG_RADIO_WL1273 is not set
CONFIG_USB_DSBR=y
CONFIG_USB_KEENE=y
# CONFIG_USB_MA901 is not set
CONFIG_USB_MR800=y
# CONFIG_USB_RAREMONO is not set
CONFIG_RADIO_SI470X=y
CONFIG_USB_SI470X=y
# CONFIG_I2C_SI470X is not set
CONFIG_USB_SI4713=y
CONFIG_PLATFORM_SI4713=y
CONFIG_I2C_SI4713=y
CONFIG_V4L_RADIO_ISA_DRIVERS=y
CONFIG_RADIO_AZTECH=y
CONFIG_RADIO_AZTECH_PORT=350
# CONFIG_RADIO_CADET is not set
# CONFIG_RADIO_GEMTEK is not set
CONFIG_RADIO_ISA=y
CONFIG_RADIO_RTRACK=y
CONFIG_RADIO_RTRACK2=y
CONFIG_RADIO_RTRACK2_PORT=30c
CONFIG_RADIO_RTRACK_PORT=30f
CONFIG_RADIO_SF16FMI=y
# CONFIG_RADIO_SF16FMR2 is not set
CONFIG_RADIO_TERRATEC=y
CONFIG_RADIO_TRUST=y
CONFIG_RADIO_TRUST_PORT=350
# CONFIG_RADIO_TYPHOON is not set
CONFIG_RADIO_ZOLTRIX=y
CONFIG_RADIO_ZOLTRIX_PORT=20c
CONFIG_MEDIA_PLATFORM_DRIVERS=y
# CONFIG_V4L_PLATFORM_DRIVERS is not set
# CONFIG_SDR_PLATFORM_DRIVERS is not set
# CONFIG_DVB_PLATFORM_DRIVERS is not set
# CONFIG_V4L_MEM2MEM_DRIVERS is not set

#
# Allegro DVT media platform drivers
#

#
# Amlogic media platform drivers
#

#
# Amphion drivers
#

#
# Aspeed media platform drivers
#

#
# Atmel media platform drivers
#

#
# Cadence media platform drivers
#
# CONFIG_VIDEO_CADENCE_CSI2RX is not set
# CONFIG_VIDEO_CADENCE_CSI2TX is not set

#
# Chips&Media media platform drivers
#

#
# Intel media platform drivers
#

#
# Marvell media platform drivers
#

#
# Mediatek media platform drivers
#
# CONFIG_VIDEO_MEDIATEK_MDP3 is not set

#
# NVidia media platform drivers
#

#
# NXP media platform drivers
#
# CONFIG_VIDEO_IMX_MIPI_CSIS is not set

#
# Qualcomm media platform drivers
#

#
# Renesas media platform drivers
#

#
# Rockchip media platform drivers
#

#
# Samsung media platform drivers
#

#
# STMicroelectronics media platform drivers
#

#
# Sunxi media platform drivers
#

#
# Texas Instruments drivers
#

#
# Verisilicon media platform drivers
#

#
# VIA media platform drivers
#

#
# Xilinx media platform drivers
#

#
# MMC/SDIO DVB adapters
#
# CONFIG_SMS_SDIO_DRV is not set
# CONFIG_V4L_TEST_DRIVERS is not set
# CONFIG_DVB_TEST_DRIVERS is not set

#
# FireWire (IEEE 1394) Adapters
#
CONFIG_DVB_FIREDTV=y
CONFIG_DVB_FIREDTV_INPUT=y
CONFIG_VIDEOBUF2_CORE=y
CONFIG_VIDEOBUF2_V4L2=y
CONFIG_VIDEOBUF2_MEMOPS=y
CONFIG_VIDEOBUF2_DMA_CONTIG=y
CONFIG_VIDEOBUF2_VMALLOC=y
# end of Media drivers

#
# Media ancillary drivers
#

#
# IR I2C driver auto-selected by 'Autoselect ancillary drivers'
#
CONFIG_VIDEO_IR_I2C=y

#
# Camera sensor devices
#
CONFIG_VIDEO_APTINA_PLL=y
CONFIG_VIDEO_CCS_PLL=y
# CONFIG_VIDEO_AR0521 is not set
# CONFIG_VIDEO_HI556 is not set
# CONFIG_VIDEO_HI846 is not set
# CONFIG_VIDEO_HI847 is not set
CONFIG_VIDEO_IMX208=y
# CONFIG_VIDEO_IMX214 is not set
# CONFIG_VIDEO_IMX219 is not set
# CONFIG_VIDEO_IMX258 is not set
CONFIG_VIDEO_IMX274=y
# CONFIG_VIDEO_IMX290 is not set
CONFIG_VIDEO_IMX319=y
# CONFIG_VIDEO_IMX334 is not set
CONFIG_VIDEO_IMX335=y
# CONFIG_VIDEO_IMX355 is not set
CONFIG_VIDEO_IMX412=y
CONFIG_VIDEO_MAX9271_LIB=y
CONFIG_VIDEO_MT9M001=y
# CONFIG_VIDEO_MT9M032 is not set
CONFIG_VIDEO_MT9M111=y
CONFIG_VIDEO_MT9P031=y
# CONFIG_VIDEO_MT9T001 is not set
CONFIG_VIDEO_MT9T112=y
CONFIG_VIDEO_MT9V011=y
CONFIG_VIDEO_MT9V032=y
CONFIG_VIDEO_MT9V111=y
# CONFIG_VIDEO_NOON010PC30 is not set
# CONFIG_VIDEO_OG01A1B is not set
# CONFIG_VIDEO_OV02A10 is not set
# CONFIG_VIDEO_OV08D10 is not set
CONFIG_VIDEO_OV13858=y
# CONFIG_VIDEO_OV13B10 is not set
# CONFIG_VIDEO_OV2640 is not set
CONFIG_VIDEO_OV2659=y
CONFIG_VIDEO_OV2680=y
# CONFIG_VIDEO_OV2685 is not set
CONFIG_VIDEO_OV2740=y
# CONFIG_VIDEO_OV5640 is not set
CONFIG_VIDEO_OV5645=y
CONFIG_VIDEO_OV5647=y
# CONFIG_VIDEO_OV5670 is not set
# CONFIG_VIDEO_OV5675 is not set
# CONFIG_VIDEO_OV5693 is not set
# CONFIG_VIDEO_OV5695 is not set
# CONFIG_VIDEO_OV6650 is not set
CONFIG_VIDEO_OV7251=y
CONFIG_VIDEO_OV7640=y
CONFIG_VIDEO_OV7670=y
# CONFIG_VIDEO_OV772X is not set
CONFIG_VIDEO_OV7740=y
# CONFIG_VIDEO_OV8856 is not set
CONFIG_VIDEO_OV9282=y
CONFIG_VIDEO_OV9640=y
CONFIG_VIDEO_OV9650=y
CONFIG_VIDEO_OV9734=y
CONFIG_VIDEO_RDACM20=y
CONFIG_VIDEO_RDACM21=y
CONFIG_VIDEO_RJ54N1=y
CONFIG_VIDEO_S5C73M3=y
CONFIG_VIDEO_S5K4ECGX=y
CONFIG_VIDEO_S5K5BAF=y
# CONFIG_VIDEO_S5K6A3 is not set
CONFIG_VIDEO_S5K6AA=y
# CONFIG_VIDEO_SR030PC30 is not set
CONFIG_VIDEO_VS6624=y
CONFIG_VIDEO_CCS=y
# CONFIG_VIDEO_ET8EK8 is not set
# CONFIG_VIDEO_M5MOLS is not set
# end of Camera sensor devices

#
# Lens drivers
#
# CONFIG_VIDEO_AD5820 is not set
CONFIG_VIDEO_AK7375=y
# CONFIG_VIDEO_DW9714 is not set
# CONFIG_VIDEO_DW9768 is not set
CONFIG_VIDEO_DW9807_VCM=y
# end of Lens drivers

#
# Flash devices
#
CONFIG_VIDEO_ADP1653=y
# CONFIG_VIDEO_LM3560 is not set
CONFIG_VIDEO_LM3646=y
# end of Flash devices

#
# Audio decoders, processors and mixers
#
# CONFIG_VIDEO_CS3308 is not set
CONFIG_VIDEO_CS5345=y
CONFIG_VIDEO_CS53L32A=y
# CONFIG_VIDEO_MSP3400 is not set
CONFIG_VIDEO_SONY_BTF_MPX=y
# CONFIG_VIDEO_TDA7432 is not set
CONFIG_VIDEO_TDA9840=y
CONFIG_VIDEO_TEA6415C=y
# CONFIG_VIDEO_TEA6420 is not set
CONFIG_VIDEO_TLV320AIC23B=y
# CONFIG_VIDEO_TVAUDIO is not set
# CONFIG_VIDEO_UDA1342 is not set
CONFIG_VIDEO_VP27SMPX=y
# CONFIG_VIDEO_WM8739 is not set
CONFIG_VIDEO_WM8775=y
# end of Audio decoders, processors and mixers

#
# RDS decoders
#
CONFIG_VIDEO_SAA6588=y
# end of RDS decoders

#
# Video decoders
#
# CONFIG_VIDEO_ADV7180 is not set
# CONFIG_VIDEO_ADV7183 is not set
CONFIG_VIDEO_ADV748X=y
CONFIG_VIDEO_ADV7604=y
CONFIG_VIDEO_ADV7604_CEC=y
# CONFIG_VIDEO_ADV7842 is not set
# CONFIG_VIDEO_BT819 is not set
CONFIG_VIDEO_BT856=y
CONFIG_VIDEO_BT866=y
# CONFIG_VIDEO_ISL7998X is not set
# CONFIG_VIDEO_KS0127 is not set
CONFIG_VIDEO_MAX9286=y
CONFIG_VIDEO_ML86V7667=y
# CONFIG_VIDEO_SAA7110 is not set
CONFIG_VIDEO_SAA711X=y
# CONFIG_VIDEO_TC358743 is not set
# CONFIG_VIDEO_TVP514X is not set
# CONFIG_VIDEO_TVP5150 is not set
# CONFIG_VIDEO_TVP7002 is not set
CONFIG_VIDEO_TW2804=y
# CONFIG_VIDEO_TW9903 is not set
CONFIG_VIDEO_TW9906=y
CONFIG_VIDEO_TW9910=y
CONFIG_VIDEO_VPX3220=y

#
# Video and audio decoders
#
CONFIG_VIDEO_SAA717X=y
CONFIG_VIDEO_CX25840=y
# end of Video decoders

#
# Video encoders
#
# CONFIG_VIDEO_AD9389B is not set
CONFIG_VIDEO_ADV7170=y
CONFIG_VIDEO_ADV7175=y
CONFIG_VIDEO_ADV7343=y
CONFIG_VIDEO_ADV7393=y
# CONFIG_VIDEO_ADV7511 is not set
CONFIG_VIDEO_AK881X=y
CONFIG_VIDEO_SAA7127=y
CONFIG_VIDEO_SAA7185=y
CONFIG_VIDEO_THS8200=y
# end of Video encoders

#
# Video improvement chips
#
CONFIG_VIDEO_UPD64031A=y
CONFIG_VIDEO_UPD64083=y
# end of Video improvement chips

#
# Audio/Video compression chips
#
# CONFIG_VIDEO_SAA6752HS is not set
# end of Audio/Video compression chips

#
# SDR tuner chips
#
# CONFIG_SDR_MAX2175 is not set
# end of SDR tuner chips

#
# Miscellaneous helper chips
#
CONFIG_VIDEO_I2C=y
# CONFIG_VIDEO_M52790 is not set
CONFIG_VIDEO_ST_MIPID02=y
CONFIG_VIDEO_THS7303=y
# end of Miscellaneous helper chips

#
# Media SPI Adapters
#
CONFIG_CXD2880_SPI_DRV=y
CONFIG_VIDEO_GS1662=y
# end of Media SPI Adapters

CONFIG_MEDIA_TUNER=y

#
# Customize TV tuners
#
# CONFIG_MEDIA_TUNER_E4000 is not set
CONFIG_MEDIA_TUNER_FC0011=y
CONFIG_MEDIA_TUNER_FC0012=y
# CONFIG_MEDIA_TUNER_FC0013 is not set
CONFIG_MEDIA_TUNER_FC2580=y
# CONFIG_MEDIA_TUNER_IT913X is not set
CONFIG_MEDIA_TUNER_M88RS6000T=y
# CONFIG_MEDIA_TUNER_MAX2165 is not set
CONFIG_MEDIA_TUNER_MC44S803=y
CONFIG_MEDIA_TUNER_MSI001=y
CONFIG_MEDIA_TUNER_MT2060=y
CONFIG_MEDIA_TUNER_MT2063=y
CONFIG_MEDIA_TUNER_MT20XX=y
# CONFIG_MEDIA_TUNER_MT2131 is not set
CONFIG_MEDIA_TUNER_MT2266=y
CONFIG_MEDIA_TUNER_MXL301RF=y
CONFIG_MEDIA_TUNER_MXL5005S=y
CONFIG_MEDIA_TUNER_MXL5007T=y
# CONFIG_MEDIA_TUNER_QM1D1B0004 is not set
# CONFIG_MEDIA_TUNER_QM1D1C0042 is not set
CONFIG_MEDIA_TUNER_QT1010=y
CONFIG_MEDIA_TUNER_R820T=y
# CONFIG_MEDIA_TUNER_SI2157 is not set
CONFIG_MEDIA_TUNER_SIMPLE=y
CONFIG_MEDIA_TUNER_TDA18212=y
CONFIG_MEDIA_TUNER_TDA18218=y
CONFIG_MEDIA_TUNER_TDA18250=y
CONFIG_MEDIA_TUNER_TDA18271=y
CONFIG_MEDIA_TUNER_TDA827X=y
CONFIG_MEDIA_TUNER_TDA8290=y
CONFIG_MEDIA_TUNER_TDA9887=y
CONFIG_MEDIA_TUNER_TEA5761=y
CONFIG_MEDIA_TUNER_TEA5767=y
# CONFIG_MEDIA_TUNER_TUA9001 is not set
CONFIG_MEDIA_TUNER_XC2028=y
CONFIG_MEDIA_TUNER_XC4000=y
CONFIG_MEDIA_TUNER_XC5000=y
# end of Customize TV tuners

#
# Customise DVB Frontends
#

#
# Multistandard (satellite) frontends
#
CONFIG_DVB_M88DS3103=y
CONFIG_DVB_MXL5XX=y
CONFIG_DVB_STB0899=y
CONFIG_DVB_STB6100=y
# CONFIG_DVB_STV090x is not set
CONFIG_DVB_STV0910=y
# CONFIG_DVB_STV6110x is not set
# CONFIG_DVB_STV6111 is not set

#
# Multistandard (cable + terrestrial) frontends
#
CONFIG_DVB_DRXK=y
CONFIG_DVB_MN88472=y
CONFIG_DVB_MN88473=y
CONFIG_DVB_SI2165=y
# CONFIG_DVB_TDA18271C2DD is not set

#
# DVB-S (satellite) frontends
#
CONFIG_DVB_CX24110=y
CONFIG_DVB_CX24116=y
CONFIG_DVB_CX24117=y
CONFIG_DVB_CX24120=y
CONFIG_DVB_CX24123=y
# CONFIG_DVB_DS3000 is not set
CONFIG_DVB_MB86A16=y
CONFIG_DVB_MT312=y
# CONFIG_DVB_S5H1420 is not set
CONFIG_DVB_SI21XX=y
# CONFIG_DVB_STB6000 is not set
CONFIG_DVB_STV0288=y
CONFIG_DVB_STV0299=y
CONFIG_DVB_STV0900=y
CONFIG_DVB_STV6110=y
CONFIG_DVB_TDA10071=y
CONFIG_DVB_TDA10086=y
CONFIG_DVB_TDA8083=y
# CONFIG_DVB_TDA8261 is not set
CONFIG_DVB_TDA826X=y
# CONFIG_DVB_TS2020 is not set
# CONFIG_DVB_TUA6100 is not set
# CONFIG_DVB_TUNER_CX24113 is not set
CONFIG_DVB_TUNER_ITD1000=y
CONFIG_DVB_VES1X93=y
CONFIG_DVB_ZL10036=y
# CONFIG_DVB_ZL10039 is not set

#
# DVB-T (terrestrial) frontends
#
# CONFIG_DVB_AF9013 is not set
CONFIG_DVB_CX22700=y
# CONFIG_DVB_CX22702 is not set
# CONFIG_DVB_CXD2820R is not set
# CONFIG_DVB_CXD2841ER is not set
CONFIG_DVB_DIB3000MB=y
CONFIG_DVB_DIB3000MC=y
# CONFIG_DVB_DIB7000M is not set
CONFIG_DVB_DIB7000P=y
CONFIG_DVB_DIB9000=y
# CONFIG_DVB_DRXD is not set
CONFIG_DVB_EC100=y
# CONFIG_DVB_L64781 is not set
CONFIG_DVB_MT352=y
CONFIG_DVB_NXT6000=y
CONFIG_DVB_RTL2830=y
CONFIG_DVB_RTL2832=y
CONFIG_DVB_RTL2832_SDR=y
# CONFIG_DVB_S5H1432 is not set
CONFIG_DVB_SI2168=y
CONFIG_DVB_SP887X=y
# CONFIG_DVB_STV0367 is not set
CONFIG_DVB_TDA10048=y
# CONFIG_DVB_TDA1004X is not set
CONFIG_DVB_ZD1301_DEMOD=y
CONFIG_DVB_ZL10353=y
CONFIG_DVB_CXD2880=y

#
# DVB-C (cable) frontends
#
# CONFIG_DVB_STV0297 is not set
CONFIG_DVB_TDA10021=y
CONFIG_DVB_TDA10023=y
# CONFIG_DVB_VES1820 is not set

#
# ATSC (North American/Korean Terrestrial/Cable DTV) frontends
#
CONFIG_DVB_AU8522=y
# CONFIG_DVB_AU8522_DTV is not set
CONFIG_DVB_AU8522_V4L=y
CONFIG_DVB_BCM3510=y
CONFIG_DVB_LG2160=y
# CONFIG_DVB_LGDT3305 is not set
# CONFIG_DVB_LGDT3306A is not set
CONFIG_DVB_LGDT330X=y
# CONFIG_DVB_MXL692 is not set
CONFIG_DVB_NXT200X=y
CONFIG_DVB_OR51132=y
# CONFIG_DVB_OR51211 is not set
CONFIG_DVB_S5H1409=y
CONFIG_DVB_S5H1411=y

#
# ISDB-T (terrestrial) frontends
#
CONFIG_DVB_DIB8000=y
# CONFIG_DVB_MB86A20S is not set
# CONFIG_DVB_S921 is not set

#
# ISDB-S (satellite) & ISDB-T (terrestrial) frontends
#
# CONFIG_DVB_MN88443X is not set
# CONFIG_DVB_TC90522 is not set

#
# Digital terrestrial only tuners/PLL
#
# CONFIG_DVB_PLL is not set
CONFIG_DVB_TUNER_DIB0070=y
# CONFIG_DVB_TUNER_DIB0090 is not set

#
# SEC control devices for DVB-S
#
# CONFIG_DVB_A8293 is not set
# CONFIG_DVB_AF9033 is not set
CONFIG_DVB_ASCOT2E=y
CONFIG_DVB_ATBM8830=y
CONFIG_DVB_HELENE=y
CONFIG_DVB_HORUS3A=y
# CONFIG_DVB_ISL6405 is not set
CONFIG_DVB_ISL6421=y
# CONFIG_DVB_ISL6423 is not set
CONFIG_DVB_IX2505V=y
# CONFIG_DVB_LGS8GL5 is not set
CONFIG_DVB_LGS8GXX=y
CONFIG_DVB_LNBH25=y
CONFIG_DVB_LNBH29=y
CONFIG_DVB_LNBP21=y
CONFIG_DVB_LNBP22=y
# CONFIG_DVB_M88RS2000 is not set
CONFIG_DVB_TDA665x=y
# CONFIG_DVB_DRX39XYJ is not set

#
# Common Interface (EN50221) controller drivers
#
CONFIG_DVB_CXD2099=y
# CONFIG_DVB_SP2 is not set
# end of Customise DVB Frontends

#
# Tools to develop new frontends
#
CONFIG_DVB_DUMMY_FE=y
# end of Media ancillary drivers

#
# Graphics support
#
CONFIG_IMX_IPUV3_CORE=y
CONFIG_DRM=y
CONFIG_DRM_MIPI_DBI=y
CONFIG_DRM_MIPI_DSI=y
CONFIG_DRM_KMS_HELPER=y
# CONFIG_DRM_LOAD_EDID_FIRMWARE is not set
CONFIG_DRM_DP_AUX_BUS=y
CONFIG_DRM_DISPLAY_HELPER=y
CONFIG_DRM_DISPLAY_DP_HELPER=y
CONFIG_DRM_DISPLAY_HDCP_HELPER=y
CONFIG_DRM_DISPLAY_HDMI_HELPER=y
# CONFIG_DRM_DP_AUX_CHARDEV is not set
# CONFIG_DRM_DP_CEC is not set
CONFIG_DRM_GEM_DMA_HELPER=y

#
# I2C encoder or helper chips
#
# CONFIG_DRM_I2C_CH7006 is not set
CONFIG_DRM_I2C_SIL164=y
CONFIG_DRM_I2C_NXP_TDA998X=y
CONFIG_DRM_I2C_NXP_TDA9950=y
# end of I2C encoder or helper chips

#
# ARM devices
#
# end of ARM devices

CONFIG_DRM_KMB_DISPLAY=y
CONFIG_DRM_RCAR_DW_HDMI=y
# CONFIG_DRM_RCAR_USE_LVDS is not set
# CONFIG_DRM_RCAR_USE_MIPI_DSI is not set
CONFIG_DRM_PANEL=y

#
# Display Panels
#
# CONFIG_DRM_PANEL_ABT_Y030XX067A is not set
CONFIG_DRM_PANEL_ARM_VERSATILE=y
CONFIG_DRM_PANEL_ASUS_Z00T_TM5P5_NT35596=y
CONFIG_DRM_PANEL_BOE_BF060Y8M_AJ0=y
# CONFIG_DRM_PANEL_BOE_HIMAX8279D is not set
CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=y
CONFIG_DRM_PANEL_DSI_CM=y
# CONFIG_DRM_PANEL_LVDS is not set
CONFIG_DRM_PANEL_EBBG_FT8719=y
CONFIG_DRM_PANEL_ELIDA_KD35T133=y
CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02=y
CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D=y
# CONFIG_DRM_PANEL_ILITEK_IL9322 is not set
CONFIG_DRM_PANEL_ILITEK_ILI9341=y
# CONFIG_DRM_PANEL_ILITEK_ILI9881C is not set
CONFIG_DRM_PANEL_INNOLUX_EJ030NA=y
CONFIG_DRM_PANEL_INNOLUX_P079ZCA=y
# CONFIG_DRM_PANEL_JDI_LT070ME05000 is not set
CONFIG_DRM_PANEL_JDI_R63452=y
CONFIG_DRM_PANEL_KHADAS_TS050=y
CONFIG_DRM_PANEL_KINGDISPLAY_KD097D04=y
CONFIG_DRM_PANEL_LEADTEK_LTK050H3146W=y
CONFIG_DRM_PANEL_LEADTEK_LTK500HD1829=y
CONFIG_DRM_PANEL_SAMSUNG_LD9040=y
CONFIG_DRM_PANEL_LG_LB035Q02=y
CONFIG_DRM_PANEL_LG_LG4573=y
CONFIG_DRM_PANEL_NEC_NL8048HL11=y
CONFIG_DRM_PANEL_NEWVISION_NV3052C=y
# CONFIG_DRM_PANEL_NOVATEK_NT35510 is not set
CONFIG_DRM_PANEL_NOVATEK_NT35560=y
CONFIG_DRM_PANEL_NOVATEK_NT35950=y
CONFIG_DRM_PANEL_NOVATEK_NT36672A=y
CONFIG_DRM_PANEL_NOVATEK_NT39016=y
# CONFIG_DRM_PANEL_MANTIX_MLAF057WE51 is not set
CONFIG_DRM_PANEL_OLIMEX_LCD_OLINUXINO=y
# CONFIG_DRM_PANEL_ORISETECH_OTM8009A is not set
CONFIG_DRM_PANEL_OSD_OSD101T2587_53TS=y
# CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00 is not set
CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN=y
# CONFIG_DRM_PANEL_RAYDIUM_RM67191 is not set
CONFIG_DRM_PANEL_RAYDIUM_RM68200=y
# CONFIG_DRM_PANEL_RONBO_RB070D30 is not set
CONFIG_DRM_PANEL_SAMSUNG_DB7430=y
# CONFIG_DRM_PANEL_SAMSUNG_S6D16D0 is not set
CONFIG_DRM_PANEL_SAMSUNG_S6D27A1=y
# CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2 is not set
CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03=y
# CONFIG_DRM_PANEL_SAMSUNG_S6E63M0 is not set
# CONFIG_DRM_PANEL_SAMSUNG_S6E88A0_AMS452EF01 is not set
# CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0 is not set
CONFIG_DRM_PANEL_SAMSUNG_SOFEF00=y
CONFIG_DRM_PANEL_SEIKO_43WVF1G=y
# CONFIG_DRM_PANEL_SHARP_LQ101R1SX01 is not set
CONFIG_DRM_PANEL_SHARP_LS037V7DW01=y
CONFIG_DRM_PANEL_SHARP_LS043T1LE01=y
CONFIG_DRM_PANEL_SHARP_LS060T1SX01=y
CONFIG_DRM_PANEL_SITRONIX_ST7701=y
CONFIG_DRM_PANEL_SITRONIX_ST7703=y
# CONFIG_DRM_PANEL_SITRONIX_ST7789V is not set
CONFIG_DRM_PANEL_SONY_ACX565AKM=y
CONFIG_DRM_PANEL_SONY_TULIP_TRULY_NT35521=y
# CONFIG_DRM_PANEL_TDO_TL070WSH30 is not set
CONFIG_DRM_PANEL_TPO_TD028TTEC1=y
CONFIG_DRM_PANEL_TPO_TD043MTEA1=y
CONFIG_DRM_PANEL_TPO_TPG110=y
# CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA is not set
# CONFIG_DRM_PANEL_VISIONOX_RM69299 is not set
CONFIG_DRM_PANEL_WIDECHIPS_WS2401=y
# CONFIG_DRM_PANEL_XINPENG_XPP055C272 is not set
# end of Display Panels

CONFIG_DRM_BRIDGE=y
CONFIG_DRM_PANEL_BRIDGE=y

#
# Display Interface Bridges
#
CONFIG_DRM_CDNS_DSI=y
CONFIG_DRM_CHIPONE_ICN6211=y
CONFIG_DRM_CHRONTEL_CH7033=y
CONFIG_DRM_CROS_EC_ANX7688=y
# CONFIG_DRM_DISPLAY_CONNECTOR is not set
CONFIG_DRM_FSL_LDB=y
CONFIG_DRM_ITE_IT6505=y
CONFIG_DRM_LONTIUM_LT8912B=y
CONFIG_DRM_LONTIUM_LT9211=y
CONFIG_DRM_LONTIUM_LT9611=y
# CONFIG_DRM_LONTIUM_LT9611UXC is not set
# CONFIG_DRM_ITE_IT66121 is not set
CONFIG_DRM_LVDS_CODEC=y
CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW=y
CONFIG_DRM_NXP_PTN3460=y
CONFIG_DRM_PARADE_PS8622=y
CONFIG_DRM_PARADE_PS8640=y
CONFIG_DRM_SIL_SII8620=y
CONFIG_DRM_SII902X=y
# CONFIG_DRM_SII9234 is not set
CONFIG_DRM_SIMPLE_BRIDGE=y
CONFIG_DRM_THINE_THC63LVD1024=y
# CONFIG_DRM_TOSHIBA_TC358762 is not set
# CONFIG_DRM_TOSHIBA_TC358764 is not set
# CONFIG_DRM_TOSHIBA_TC358767 is not set
CONFIG_DRM_TOSHIBA_TC358768=y
CONFIG_DRM_TOSHIBA_TC358775=y
CONFIG_DRM_TI_DLPC3433=y
# CONFIG_DRM_TI_TFP410 is not set
CONFIG_DRM_TI_SN65DSI83=y
# CONFIG_DRM_TI_SN65DSI86 is not set
CONFIG_DRM_TI_TPD12S015=y
CONFIG_DRM_ANALOGIX_ANX6345=y
CONFIG_DRM_ANALOGIX_ANX78XX=y
CONFIG_DRM_ANALOGIX_DP=y
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_DRM_I2C_ADV7511=y
CONFIG_DRM_I2C_ADV7511_CEC=y
CONFIG_DRM_CDNS_MHDP8546=y
# CONFIG_DRM_CDNS_MHDP8546_J721E is not set
# CONFIG_DRM_IMX8QXP_PIXEL_LINK_TO_DPI is not set
CONFIG_DRM_DW_HDMI=y
CONFIG_DRM_DW_HDMI_CEC=y
# end of Display Interface Bridges

CONFIG_DRM_IMX=y
# CONFIG_DRM_IMX_PARALLEL_DISPLAY is not set
CONFIG_DRM_IMX_HDMI=y
CONFIG_DRM_LOGICVC=y
# CONFIG_DRM_ARCPGU is not set
# CONFIG_DRM_PANEL_MIPI_DBI is not set
CONFIG_TINYDRM_HX8357D=y
CONFIG_TINYDRM_ILI9163=y
CONFIG_TINYDRM_ILI9225=y
# CONFIG_TINYDRM_ILI9341 is not set
# CONFIG_TINYDRM_ILI9486 is not set
CONFIG_TINYDRM_MI0283QT=y
CONFIG_TINYDRM_REPAPER=y
CONFIG_TINYDRM_ST7586=y
CONFIG_TINYDRM_ST7735R=y
CONFIG_DRM_TIDSS=y
# CONFIG_DRM_SPRD is not set
CONFIG_DRM_PANEL_ORIENTATION_QUIRKS=y
CONFIG_DRM_NOMODESET=y

#
# Frame buffer Devices
#
CONFIG_FB_CMDLINE=y
# CONFIG_FB is not set
# CONFIG_MMP_DISP is not set
# end of Frame buffer Devices

#
# Backlight & LCD device support
#
CONFIG_LCD_CLASS_DEVICE=y
# CONFIG_LCD_L4F00242T03 is not set
CONFIG_LCD_LMS283GF05=y
CONFIG_LCD_LTV350QV=y
# CONFIG_LCD_ILI922X is not set
CONFIG_LCD_ILI9320=y
# CONFIG_LCD_TDO24M is not set
# CONFIG_LCD_VGG2432A4 is not set
# CONFIG_LCD_PLATFORM is not set
# CONFIG_LCD_AMS369FG06 is not set
CONFIG_LCD_LMS501KF03=y
CONFIG_LCD_HX8357=y
# CONFIG_LCD_OTM3225A is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_BACKLIGHT_KTD253=y
CONFIG_BACKLIGHT_LM3533=y
# CONFIG_BACKLIGHT_OMAP1 is not set
# CONFIG_BACKLIGHT_DA9052 is not set
CONFIG_BACKLIGHT_QCOM_WLED=y
# CONFIG_BACKLIGHT_RT4831 is not set
CONFIG_BACKLIGHT_ADP8860=y
CONFIG_BACKLIGHT_ADP8870=y
# CONFIG_BACKLIGHT_88PM860X is not set
CONFIG_BACKLIGHT_AAT2870=y
CONFIG_BACKLIGHT_LM3639=y
# CONFIG_BACKLIGHT_PANDORA is not set
CONFIG_BACKLIGHT_GPIO=y
# CONFIG_BACKLIGHT_LV5207LP is not set
CONFIG_BACKLIGHT_BD6107=y
# CONFIG_BACKLIGHT_ARCXCNN is not set
# CONFIG_BACKLIGHT_RAVE_SP is not set
# CONFIG_BACKLIGHT_LED is not set
# end of Backlight & LCD device support

CONFIG_VIDEOMODE_HELPERS=y
CONFIG_HDMI=y

#
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
CONFIG_DUMMY_CONSOLE_COLUMNS=80
CONFIG_DUMMY_CONSOLE_ROWS=25
# end of Console display driver support
# end of Graphics support

# CONFIG_SOUND is not set

#
# HID support
#
CONFIG_HID=y
# CONFIG_HID_BATTERY_STRENGTH is not set
CONFIG_HIDRAW=y
CONFIG_UHID=y
# CONFIG_HID_GENERIC is not set

#
# Special HID drivers
#
CONFIG_HID_A4TECH=y
CONFIG_HID_ACCUTOUCH=y
# CONFIG_HID_ACRUX is not set
CONFIG_HID_APPLE=y
# CONFIG_HID_APPLEIR is not set
CONFIG_HID_ASUS=y
CONFIG_HID_AUREAL=y
CONFIG_HID_BELKIN=y
# CONFIG_HID_BETOP_FF is not set
CONFIG_HID_BIGBEN_FF=y
CONFIG_HID_CHERRY=y
# CONFIG_HID_CHICONY is not set
CONFIG_HID_CORSAIR=y
# CONFIG_HID_COUGAR is not set
# CONFIG_HID_MACALLY is not set
CONFIG_HID_CMEDIA=y
CONFIG_HID_CP2112=y
CONFIG_HID_CREATIVE_SB0540=y
CONFIG_HID_CYPRESS=y
# CONFIG_HID_DRAGONRISE is not set
CONFIG_HID_EMS_FF=y
# CONFIG_HID_ELAN is not set
CONFIG_HID_ELECOM=y
CONFIG_HID_ELO=y
# CONFIG_HID_EZKEY is not set
# CONFIG_HID_FT260 is not set
# CONFIG_HID_GEMBIRD is not set
CONFIG_HID_GFRM=y
CONFIG_HID_GLORIOUS=y
CONFIG_HID_HOLTEK=y
CONFIG_HOLTEK_FF=y
CONFIG_HID_VIVALDI_COMMON=y
CONFIG_HID_GOOGLE_HAMMER=y
CONFIG_HID_VIVALDI=y
CONFIG_HID_GT683R=y
CONFIG_HID_KEYTOUCH=y
# CONFIG_HID_KYE is not set
CONFIG_HID_UCLOGIC=y
CONFIG_HID_WALTOP=y
CONFIG_HID_VIEWSONIC=y
# CONFIG_HID_VRC2 is not set
# CONFIG_HID_XIAOMI is not set
CONFIG_HID_GYRATION=y
CONFIG_HID_ICADE=y
CONFIG_HID_ITE=y
CONFIG_HID_JABRA=y
# CONFIG_HID_TWINHAN is not set
CONFIG_HID_KENSINGTON=y
# CONFIG_HID_LCPOWER is not set
CONFIG_HID_LED=y
CONFIG_HID_LENOVO=y
# CONFIG_HID_LETSKETCH is not set
# CONFIG_HID_LOGITECH is not set
# CONFIG_HID_MAGICMOUSE is not set
CONFIG_HID_MALTRON=y
# CONFIG_HID_MAYFLASH is not set
# CONFIG_HID_MEGAWORLD_FF is not set
CONFIG_HID_REDRAGON=y
CONFIG_HID_MICROSOFT=y
CONFIG_HID_MONTEREY=y
CONFIG_HID_MULTITOUCH=y
# CONFIG_HID_NINTENDO is not set
# CONFIG_HID_NTI is not set
CONFIG_HID_NTRIG=y
CONFIG_HID_ORTEK=y
CONFIG_HID_PANTHERLORD=y
CONFIG_PANTHERLORD_FF=y
CONFIG_HID_PENMOUNT=y
CONFIG_HID_PETALYNX=y
CONFIG_HID_PICOLCD=y
CONFIG_HID_PICOLCD_BACKLIGHT=y
CONFIG_HID_PICOLCD_LCD=y
CONFIG_HID_PICOLCD_LEDS=y
CONFIG_HID_PICOLCD_CIR=y
CONFIG_HID_PLANTRONICS=y
CONFIG_HID_PLAYSTATION=y
# CONFIG_PLAYSTATION_FF is not set
# CONFIG_HID_PXRC is not set
# CONFIG_HID_RAZER is not set
CONFIG_HID_PRIMAX=y
CONFIG_HID_RETRODE=y
# CONFIG_HID_ROCCAT is not set
CONFIG_HID_SAITEK=y
CONFIG_HID_SAMSUNG=y
CONFIG_HID_SEMITEK=y
# CONFIG_HID_SIGMAMICRO is not set
CONFIG_HID_SONY=y
# CONFIG_SONY_FF is not set
# CONFIG_HID_SPEEDLINK is not set
CONFIG_HID_STEAM=y
CONFIG_HID_STEELSERIES=y
# CONFIG_HID_SUNPLUS is not set
CONFIG_HID_RMI=y
CONFIG_HID_GREENASIA=y
CONFIG_GREENASIA_FF=y
CONFIG_HID_SMARTJOYPLUS=y
CONFIG_SMARTJOYPLUS_FF=y
CONFIG_HID_TIVO=y
# CONFIG_HID_TOPSEED is not set
# CONFIG_HID_TOPRE is not set
CONFIG_HID_THINGM=y
CONFIG_HID_THRUSTMASTER=y
# CONFIG_THRUSTMASTER_FF is not set
CONFIG_HID_UDRAW_PS3=y
CONFIG_HID_U2FZERO=y
CONFIG_HID_WACOM=y
CONFIG_HID_WIIMOTE=y
CONFIG_HID_XINMO=y
CONFIG_HID_ZEROPLUS=y
CONFIG_ZEROPLUS_FF=y
# CONFIG_HID_ZYDACRON is not set
CONFIG_HID_SENSOR_HUB=y
# CONFIG_HID_SENSOR_CUSTOM_SENSOR is not set
CONFIG_HID_ALPS=y
CONFIG_HID_MCP2221=y
# end of Special HID drivers

#
# USB HID support
#
CONFIG_USB_HID=y
# CONFIG_HID_PID is not set
# CONFIG_USB_HIDDEV is not set
# end of USB HID support

#
# I2C HID support
#
CONFIG_I2C_HID_OF=y
# CONFIG_I2C_HID_OF_ELAN is not set
CONFIG_I2C_HID_OF_GOODIX=y
# end of I2C HID support

CONFIG_I2C_HID_CORE=y
# end of HID support

CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
# CONFIG_USB_LED_TRIG is not set
CONFIG_USB_ULPI_BUS=y
CONFIG_USB_CONN_GPIO=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEFAULT_PERSIST=y
# CONFIG_USB_FEW_INIT_RETRIES is not set
CONFIG_USB_DYNAMIC_MINORS=y
# CONFIG_USB_OTG_PRODUCTLIST is not set
CONFIG_USB_LEDS_TRIGGER_USBPORT=y
CONFIG_USB_AUTOSUSPEND_DELAY=2
CONFIG_USB_MON=y

#
# USB Host Controller Drivers
#
CONFIG_USB_C67X00_HCD=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DBGCAP=y
# CONFIG_USB_XHCI_PCI_RENESAS is not set
CONFIG_USB_XHCI_PLATFORM=y
# CONFIG_USB_XHCI_HISTB is not set
CONFIG_USB_XHCI_MTK=y
CONFIG_USB_XHCI_MVEBU=y
# CONFIG_USB_XHCI_RCAR is not set
# CONFIG_USB_BRCMSTB is not set
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
CONFIG_USB_EHCI_FSL=y
# CONFIG_USB_EHCI_HCD_NPCM7XX is not set
CONFIG_USB_EHCI_HCD_OMAP=y
CONFIG_USB_EHCI_HCD_ORION=y
CONFIG_USB_EHCI_HCD_SPEAR=y
CONFIG_USB_EHCI_HCD_STI=y
CONFIG_USB_EHCI_HCD_AT91=y
CONFIG_USB_EHCI_SH=y
CONFIG_USB_EHCI_EXYNOS=y
CONFIG_USB_EHCI_MV=y
# CONFIG_USB_CNS3XXX_EHCI is not set
CONFIG_USB_EHCI_HCD_PLATFORM=y
CONFIG_USB_OXU210HP_HCD=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_ISP1362_HCD=y
# CONFIG_USB_FOTG210_HCD is not set
# CONFIG_USB_MAX3421_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_HCD_SPEAR is not set
# CONFIG_USB_OHCI_HCD_STI is not set
CONFIG_USB_OHCI_HCD_S3C2410=y
CONFIG_USB_OHCI_HCD_LPC32XX=y
CONFIG_USB_OHCI_HCD_AT91=y
CONFIG_USB_OHCI_HCD_OMAP3=y
CONFIG_USB_OHCI_HCD_DAVINCI=y
CONFIG_USB_OHCI_HCD_SSB=y
CONFIG_USB_OHCI_SH=y
CONFIG_USB_OHCI_EXYNOS=y
CONFIG_USB_CNS3XXX_OHCI=y
CONFIG_USB_OHCI_HCD_PLATFORM=y
CONFIG_USB_U132_HCD=y
# CONFIG_USB_SL811_HCD is not set
CONFIG_USB_R8A66597_HCD=y
CONFIG_USB_HCD_BCMA=y
CONFIG_USB_HCD_SSB=y
# CONFIG_USB_HCD_TEST_MODE is not set

#
# USB Device Class drivers
#
CONFIG_USB_ACM=y
CONFIG_USB_PRINTER=y
CONFIG_USB_WDM=y
CONFIG_USB_TMC=y

#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#

#
# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_REALTEK is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
CONFIG_USB_STORAGE_FREECOM=y
# CONFIG_USB_STORAGE_ISD200 is not set
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
# CONFIG_USB_STORAGE_JUMPSHOT is not set
CONFIG_USB_STORAGE_ALAUDA=y
CONFIG_USB_STORAGE_ONETOUCH=y
CONFIG_USB_STORAGE_KARMA=y
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
CONFIG_USB_STORAGE_ENE_UB6250=y
# CONFIG_USB_UAS is not set

#
# USB Imaging devices
#
CONFIG_USB_MDC800=y
CONFIG_USB_MICROTEK=y
CONFIG_USBIP_CORE=y
CONFIG_USBIP_VHCI_HCD=y
CONFIG_USBIP_VHCI_HC_PORTS=8
CONFIG_USBIP_VHCI_NR_HCS=1
CONFIG_USBIP_HOST=y
CONFIG_USBIP_DEBUG=y
CONFIG_USB_CDNS_SUPPORT=y
# CONFIG_USB_CDNS3 is not set
CONFIG_USB_MTU3=y
CONFIG_USB_MTU3_HOST=y
# CONFIG_USB_MTU3_DEBUG is not set
CONFIG_USB_MUSB_HDRC=y
CONFIG_USB_MUSB_HOST=y

#
# Platform Glue Layer
#
# CONFIG_USB_MUSB_TUSB6010 is not set
CONFIG_USB_MUSB_DSPS=y
# CONFIG_USB_MUSB_UX500 is not set
# CONFIG_USB_MUSB_MEDIATEK is not set
# CONFIG_USB_MUSB_POLARFIRE_SOC is not set

#
# MUSB DMA mode
#
CONFIG_MUSB_PIO_ONLY=y
# CONFIG_USB_DWC3 is not set
# CONFIG_USB_DWC2 is not set
CONFIG_USB_CHIPIDEA=y
CONFIG_USB_CHIPIDEA_HOST=y
CONFIG_USB_CHIPIDEA_MSM=y
CONFIG_USB_CHIPIDEA_IMX=y
CONFIG_USB_CHIPIDEA_GENERIC=y
CONFIG_USB_CHIPIDEA_TEGRA=y
# CONFIG_USB_ISP1760 is not set

#
# USB port drivers
#
CONFIG_USB_USS720=y
CONFIG_USB_SERIAL=y
# CONFIG_USB_SERIAL_CONSOLE is not set
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_SIMPLE is not set
CONFIG_USB_SERIAL_AIRCABLE=y
CONFIG_USB_SERIAL_ARK3116=y
# CONFIG_USB_SERIAL_BELKIN is not set
CONFIG_USB_SERIAL_CH341=y
CONFIG_USB_SERIAL_WHITEHEAT=y
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=y
CONFIG_USB_SERIAL_CP210X=y
CONFIG_USB_SERIAL_CYPRESS_M8=y
# CONFIG_USB_SERIAL_EMPEG is not set
CONFIG_USB_SERIAL_FTDI_SIO=y
CONFIG_USB_SERIAL_VISOR=y
CONFIG_USB_SERIAL_IPAQ=y
CONFIG_USB_SERIAL_IR=y
CONFIG_USB_SERIAL_EDGEPORT=y
CONFIG_USB_SERIAL_EDGEPORT_TI=y
CONFIG_USB_SERIAL_F81232=y
CONFIG_USB_SERIAL_F8153X=y
# CONFIG_USB_SERIAL_GARMIN is not set
CONFIG_USB_SERIAL_IPW=y
CONFIG_USB_SERIAL_IUU=y
CONFIG_USB_SERIAL_KEYSPAN_PDA=y
CONFIG_USB_SERIAL_KEYSPAN=y
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
CONFIG_USB_SERIAL_MCT_U232=y
CONFIG_USB_SERIAL_METRO=y
CONFIG_USB_SERIAL_MOS7720=y
# CONFIG_USB_SERIAL_MOS7715_PARPORT is not set
CONFIG_USB_SERIAL_MOS7840=y
CONFIG_USB_SERIAL_MXUPORT=y
CONFIG_USB_SERIAL_NAVMAN=y
CONFIG_USB_SERIAL_PL2303=y
# CONFIG_USB_SERIAL_OTI6858 is not set
# CONFIG_USB_SERIAL_QCAUX is not set
CONFIG_USB_SERIAL_QUALCOMM=y
CONFIG_USB_SERIAL_SPCP8X5=y
# CONFIG_USB_SERIAL_SAFE is not set
CONFIG_USB_SERIAL_SIERRAWIRELESS=y
# CONFIG_USB_SERIAL_SYMBOL is not set
# CONFIG_USB_SERIAL_TI is not set
CONFIG_USB_SERIAL_CYBERJACK=y
CONFIG_USB_SERIAL_WWAN=y
CONFIG_USB_SERIAL_OPTION=y
CONFIG_USB_SERIAL_OMNINET=y
CONFIG_USB_SERIAL_OPTICON=y
CONFIG_USB_SERIAL_XSENS_MT=y
CONFIG_USB_SERIAL_WISHBONE=y
CONFIG_USB_SERIAL_SSU100=y
# CONFIG_USB_SERIAL_QT2 is not set
CONFIG_USB_SERIAL_UPD78F0730=y
CONFIG_USB_SERIAL_XR=y
CONFIG_USB_SERIAL_DEBUG=y

#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=y
CONFIG_USB_EMI26=y
CONFIG_USB_ADUTUX=y
CONFIG_USB_SEVSEG=y
# CONFIG_USB_LEGOTOWER is not set
CONFIG_USB_LCD=y
CONFIG_USB_CYPRESS_CY7C63=y
CONFIG_USB_CYTHERM=y
CONFIG_USB_IDMOUSE=y
CONFIG_USB_FTDI_ELAN=y
CONFIG_USB_APPLEDISPLAY=y
# CONFIG_USB_QCOM_EUD is not set
CONFIG_APPLE_MFI_FASTCHARGE=y
CONFIG_USB_SISUSBVGA=y
# CONFIG_USB_LD is not set
CONFIG_USB_TRANCEVIBRATOR=y
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
CONFIG_USB_EHSET_TEST_FIXTURE=y
# CONFIG_USB_ISIGHTFW is not set
CONFIG_USB_YUREX=y
CONFIG_USB_EZUSB_FX2=y
CONFIG_USB_HUB_USB251XB=y
# CONFIG_USB_HSIC_USB3503 is not set
# CONFIG_USB_HSIC_USB4604 is not set
CONFIG_USB_LINK_LAYER_TEST=y
CONFIG_USB_CHAOSKEY=y
# CONFIG_BRCM_USB_PINMAP is not set
CONFIG_USB_ONBOARD_HUB=y

#
# USB Physical Layer drivers
#
CONFIG_USB_PHY=y
CONFIG_KEYSTONE_USB_PHY=y
CONFIG_NOP_USB_XCEIV=y
CONFIG_AM335X_CONTROL_USB=y
CONFIG_AM335X_PHY_USB=y
# CONFIG_USB_GPIO_VBUS is not set
CONFIG_TAHVO_USB=y
CONFIG_TAHVO_USB_HOST_BY_DEFAULT=y
CONFIG_USB_ISP1301=y
# CONFIG_USB_TEGRA_PHY is not set
# CONFIG_USB_ULPI is not set
# CONFIG_JZ4770_PHY is not set
# end of USB Physical Layer drivers

# CONFIG_USB_GADGET is not set
CONFIG_TYPEC=y
CONFIG_TYPEC_TCPM=y
CONFIG_TYPEC_TCPCI=y
# CONFIG_TYPEC_RT1711H is not set
# CONFIG_TYPEC_MT6360 is not set
CONFIG_TYPEC_TCPCI_MAXIM=y
# CONFIG_TYPEC_FUSB302 is not set
# CONFIG_TYPEC_TPS6598X is not set
# CONFIG_TYPEC_ANX7411 is not set
# CONFIG_TYPEC_RT1719 is not set
# CONFIG_TYPEC_HD3SS3220 is not set
# CONFIG_TYPEC_STUSB160X is not set
CONFIG_TYPEC_QCOM_PMIC=y
# CONFIG_TYPEC_WUSB3801 is not set

#
# USB Type-C Multiplexer/DeMultiplexer Switch support
#
# CONFIG_TYPEC_MUX_FSA4480 is not set
# CONFIG_TYPEC_MUX_PI3USB30532 is not set
# end of USB Type-C Multiplexer/DeMultiplexer Switch support

#
# USB Type-C Alternate Mode drivers
#
CONFIG_TYPEC_DP_ALTMODE=y
# CONFIG_TYPEC_NVIDIA_ALTMODE is not set
# end of USB Type-C Alternate Mode drivers

CONFIG_USB_ROLE_SWITCH=y
CONFIG_MMC=y
# CONFIG_PWRSEQ_EMMC is not set
# CONFIG_PWRSEQ_SIMPLE is not set
# CONFIG_MMC_BLOCK is not set
CONFIG_SDIO_UART=y
CONFIG_MMC_TEST=y

#
# MMC/SD/SDIO Host Controller Drivers
#
CONFIG_MMC_DEBUG=y
# CONFIG_MMC_SDHCI is not set
# CONFIG_MMC_MOXART is not set
# CONFIG_MMC_OMAP_HS is not set
# CONFIG_MMC_DAVINCI is not set
# CONFIG_MMC_SPI is not set
CONFIG_MMC_S3C=y
# CONFIG_MMC_S3C_HW_SDIO_IRQ is not set
# CONFIG_MMC_S3C_PIO is not set
CONFIG_MMC_S3C_DMA=y
CONFIG_MMC_TMIO_CORE=y
CONFIG_MMC_TMIO=y
CONFIG_MMC_SDHI=y
# CONFIG_MMC_SDHI_SYS_DMAC is not set
CONFIG_MMC_SDHI_INTERNAL_DMAC=y
CONFIG_MMC_UNIPHIER=y
# CONFIG_MMC_DW is not set
CONFIG_MMC_SH_MMCIF=y
CONFIG_MMC_VUB300=y
CONFIG_MMC_USHC=y
CONFIG_MMC_USDHI6ROL0=y
# CONFIG_MMC_REALTEK_USB is not set
# CONFIG_MMC_CQHCI is not set
# CONFIG_MMC_HSQ is not set
# CONFIG_MMC_BCM2835 is not set
# CONFIG_MMC_OWL is not set
# CONFIG_MMC_LITEX is not set
# CONFIG_SCSI_UFSHCD is not set
CONFIG_MEMSTICK=y
# CONFIG_MEMSTICK_DEBUG is not set

#
# MemoryStick drivers
#
CONFIG_MEMSTICK_UNSAFE_RESUME=y
CONFIG_MSPRO_BLOCK=y
# CONFIG_MS_BLOCK is not set

#
# MemoryStick Host Controller Drivers
#
CONFIG_MEMSTICK_REALTEK_USB=y
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_CLASS_FLASH=y
CONFIG_LEDS_CLASS_MULTICOLOR=y
# CONFIG_LEDS_BRIGHTNESS_HW_CHANGED is not set

#
# LED drivers
#
# CONFIG_LEDS_88PM860X is not set
CONFIG_LEDS_AN30259A=y
# CONFIG_LEDS_ARIEL is not set
CONFIG_LEDS_AW2013=y
CONFIG_LEDS_BCM6328=y
# CONFIG_LEDS_BCM6358 is not set
CONFIG_LEDS_CR0014114=y
CONFIG_LEDS_EL15203000=y
CONFIG_LEDS_TURRIS_OMNIA=y
CONFIG_LEDS_LM3530=y
CONFIG_LEDS_LM3532=y
CONFIG_LEDS_LM3533=y
CONFIG_LEDS_LM3642=y
# CONFIG_LEDS_LM3692X is not set
CONFIG_LEDS_MT6323=y
CONFIG_LEDS_S3C24XX=y
CONFIG_LEDS_COBALT_QUBE=y
# CONFIG_LEDS_COBALT_RAQ is not set
CONFIG_LEDS_PCA9532=y
# CONFIG_LEDS_PCA9532_GPIO is not set
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_LP3944=y
CONFIG_LEDS_LP3952=y
CONFIG_LEDS_LP50XX=y
CONFIG_LEDS_LP55XX_COMMON=y
# CONFIG_LEDS_LP5521 is not set
# CONFIG_LEDS_LP5523 is not set
# CONFIG_LEDS_LP5562 is not set
# CONFIG_LEDS_LP8501 is not set
# CONFIG_LEDS_LP8860 is not set
# CONFIG_LEDS_PCA955X is not set
CONFIG_LEDS_PCA963X=y
CONFIG_LEDS_DA9052=y
CONFIG_LEDS_DAC124S085=y
# CONFIG_LEDS_REGULATOR is not set
# CONFIG_LEDS_BD2802 is not set
# CONFIG_LEDS_LT3593 is not set
# CONFIG_LEDS_MC13783 is not set
CONFIG_LEDS_NS2=y
CONFIG_LEDS_NETXBIG=y
CONFIG_LEDS_TCA6507=y
CONFIG_LEDS_TLC591XX=y
CONFIG_LEDS_MAX8997=y
CONFIG_LEDS_LM355x=y
CONFIG_LEDS_OT200=y
CONFIG_LEDS_MENF21BMC=y
CONFIG_LEDS_IS31FL319X=y
CONFIG_LEDS_IS31FL32XX=y
# CONFIG_LEDS_SC27XX_BLTC is not set

#
# LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)
#
CONFIG_LEDS_BLINKM=y
# CONFIG_LEDS_SYSCON is not set
CONFIG_LEDS_MLXREG=y
# CONFIG_LEDS_USER is not set
CONFIG_LEDS_SPI_BYTE=y
# CONFIG_LEDS_TI_LMU_COMMON is not set
CONFIG_LEDS_TPS6105X=y
CONFIG_LEDS_IP30=y
CONFIG_LEDS_ACER_A500=y
# CONFIG_LEDS_BCM63138 is not set
# CONFIG_LEDS_LGM is not set

#
# Flash and Torch LED drivers
#
CONFIG_LEDS_AAT1290=y
# CONFIG_LEDS_AS3645A is not set
CONFIG_LEDS_KTD2692=y
CONFIG_LEDS_LM3601X=y
CONFIG_LEDS_MAX77693=y
# CONFIG_LEDS_MT6360 is not set
CONFIG_LEDS_RT4505=y
CONFIG_LEDS_RT8515=y
CONFIG_LEDS_SGM3140=y

#
# RGB LED drivers
#

#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
# CONFIG_LEDS_TRIGGER_TIMER is not set
CONFIG_LEDS_TRIGGER_ONESHOT=y
CONFIG_LEDS_TRIGGER_DISK=y
# CONFIG_LEDS_TRIGGER_MTD is not set
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
CONFIG_LEDS_TRIGGER_CPU=y
CONFIG_LEDS_TRIGGER_ACTIVITY=y
CONFIG_LEDS_TRIGGER_GPIO=y
# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set

#
# iptables trigger is under Netfilter config (LED target)
#
CONFIG_LEDS_TRIGGER_TRANSIENT=y
CONFIG_LEDS_TRIGGER_CAMERA=y
CONFIG_LEDS_TRIGGER_PANIC=y
# CONFIG_LEDS_TRIGGER_NETDEV is not set
CONFIG_LEDS_TRIGGER_PATTERN=y
CONFIG_LEDS_TRIGGER_AUDIO=y
CONFIG_LEDS_TRIGGER_TTY=y

#
# Simple LED drivers
#
CONFIG_ACCESSIBILITY=y
# CONFIG_A11Y_BRAILLE_CONSOLE is not set

#
# Speakup console speech
#
# CONFIG_SPEAKUP is not set
# end of Speakup console speech

# CONFIG_RTC_CLASS is not set
CONFIG_DMADEVICES=y
CONFIG_DMADEVICES_DEBUG=y
# CONFIG_DMADEVICES_VDEBUG is not set

#
# DMA Devices
#
CONFIG_ASYNC_TX_ENABLE_CHANNEL_SWITCH=y
CONFIG_DMA_ENGINE=y
CONFIG_DMA_VIRTUAL_CHANNELS=y
CONFIG_DMA_OF=y
CONFIG_ALTERA_MSGDMA=y
# CONFIG_APPLE_ADMAC is not set
CONFIG_AXI_DMAC=y
CONFIG_BCM_SBA_RAID=y
CONFIG_DMA_JZ4780=y
CONFIG_DMA_SA11X0=y
CONFIG_DMA_SUN6I=y
CONFIG_DW_AXI_DMAC=y
CONFIG_EP93XX_DMA=y
CONFIG_FSL_EDMA=y
CONFIG_IMG_MDC_DMA=y
CONFIG_INTEL_IDMA64=y
# CONFIG_INTEL_IOP_ADMA is not set
CONFIG_K3_DMA=y
CONFIG_MCF_EDMA=y
CONFIG_MILBEAUT_HDMAC=y
CONFIG_MILBEAUT_XDMAC=y
CONFIG_MMP_PDMA=y
# CONFIG_MMP_TDMA is not set
# CONFIG_MV_XOR is not set
# CONFIG_MXS_DMA is not set
# CONFIG_NBPFAXI_DMA is not set
# CONFIG_STM32_DMA is not set
# CONFIG_STM32_DMAMUX is not set
# CONFIG_STM32_MDMA is not set
CONFIG_SPRD_DMA=y
CONFIG_S3C24XX_DMAC=y
CONFIG_TEGRA20_APB_DMA=y
CONFIG_TEGRA210_ADMA=y
CONFIG_TIMB_DMA=y
CONFIG_UNIPHIER_MDMAC=y
CONFIG_UNIPHIER_XDMAC=y
CONFIG_XGENE_DMA=y
# CONFIG_XILINX_ZYNQMP_DMA is not set
CONFIG_XILINX_ZYNQMP_DPDMA=y
CONFIG_MTK_HSDMA=y
CONFIG_MTK_CQDMA=y
CONFIG_MTK_UART_APDMA=y
CONFIG_QCOM_ADM=y
# CONFIG_QCOM_HIDMA_MGMT is not set
CONFIG_QCOM_HIDMA=y
CONFIG_DW_DMAC_CORE=y
CONFIG_DW_DMAC=y
# CONFIG_RZN1_DMAMUX is not set
CONFIG_SF_PDMA=y
CONFIG_RENESAS_DMA=y
CONFIG_SH_DMAE_BASE=y
# CONFIG_SH_DMAE is not set
# CONFIG_RCAR_DMAC is not set
# CONFIG_RENESAS_USB_DMAC is not set
CONFIG_RZ_DMAC=y
# CONFIG_TI_EDMA is not set
CONFIG_DMA_OMAP=y
CONFIG_TI_DMA_CROSSBAR=y
CONFIG_INTEL_LDMA=y

#
# DMA Clients
#
CONFIG_ASYNC_TX_DMA=y
# CONFIG_DMATEST is not set
CONFIG_DMA_ENGINE_RAID=y

#
# DMABUF options
#
CONFIG_SYNC_FILE=y
CONFIG_SW_SYNC=y
CONFIG_UDMABUF=y
# CONFIG_DMABUF_MOVE_NOTIFY is not set
CONFIG_DMABUF_DEBUG=y
CONFIG_DMABUF_SELFTESTS=y
# CONFIG_DMABUF_HEAPS is not set
# CONFIG_DMABUF_SYSFS_STATS is not set
# end of DMABUF options

CONFIG_AUXDISPLAY=y
CONFIG_CHARLCD=y
CONFIG_LINEDISP=y
CONFIG_HD44780_COMMON=y
CONFIG_HD44780=y
CONFIG_IMG_ASCII_LCD=y
CONFIG_LCD2S=y
CONFIG_PARPORT_PANEL=y
CONFIG_PANEL_PARPORT=0
CONFIG_PANEL_PROFILE=5
# CONFIG_PANEL_CHANGE_MESSAGE is not set
# CONFIG_CHARLCD_BL_OFF is not set
CONFIG_CHARLCD_BL_ON=y
# CONFIG_CHARLCD_BL_FLASH is not set
CONFIG_PANEL=y
# CONFIG_VFIO is not set
CONFIG_VIRT_DRIVERS=y
CONFIG_VIRTIO_ANCHOR=y
CONFIG_VIRTIO=y
CONFIG_VIRTIO_MENU=y
CONFIG_VIRTIO_VDPA=y
CONFIG_VIRTIO_BALLOON=y
CONFIG_VIRTIO_INPUT=y
CONFIG_VIRTIO_MMIO=y
# CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES is not set
CONFIG_VDPA=y
CONFIG_VHOST_IOTLB=y
CONFIG_VHOST=y
CONFIG_VHOST_MENU=y
# CONFIG_VHOST_NET is not set
CONFIG_VHOST_SCSI=y
CONFIG_VHOST_VSOCK=y
# CONFIG_VHOST_VDPA is not set
CONFIG_VHOST_CROSS_ENDIAN_LEGACY=y

#
# Microsoft Hyper-V guest support
#
# end of Microsoft Hyper-V guest support

# CONFIG_GREYBUS is not set
CONFIG_COMEDI=y
# CONFIG_COMEDI_DEBUG is not set
CONFIG_COMEDI_DEFAULT_BUF_SIZE_KB=2048
CONFIG_COMEDI_DEFAULT_BUF_MAXSIZE_KB=20480
# CONFIG_COMEDI_MISC_DRIVERS is not set
# CONFIG_COMEDI_ISA_DRIVERS is not set
# CONFIG_COMEDI_PCMCIA_DRIVERS is not set
CONFIG_COMEDI_USB_DRIVERS=y
CONFIG_COMEDI_DT9812=y
CONFIG_COMEDI_NI_USB6501=y
CONFIG_COMEDI_USBDUX=y
CONFIG_COMEDI_USBDUXFAST=y
CONFIG_COMEDI_USBDUXSIGMA=y
CONFIG_COMEDI_VMK80XX=y
# CONFIG_COMEDI_8255_SA is not set
CONFIG_COMEDI_KCOMEDILIB=y
# CONFIG_COMEDI_TESTS is not set
CONFIG_STAGING=y
CONFIG_OCTEON_ETHERNET=y

#
# IIO staging drivers
#

#
# Accelerometers
#
CONFIG_ADIS16203=y
CONFIG_ADIS16240=y
# end of Accelerometers

#
# Analog to digital converters
#
CONFIG_AD7816=y
# end of Analog to digital converters

#
# Analog digital bi-direction converters
#
CONFIG_ADT7316=y
CONFIG_ADT7316_SPI=y
CONFIG_ADT7316_I2C=y
# end of Analog digital bi-direction converters

#
# Direct Digital Synthesis
#
CONFIG_AD9832=y
CONFIG_AD9834=y
# end of Direct Digital Synthesis

#
# Network Analyzer, Impedance Converters
#
# CONFIG_AD5933 is not set
# end of Network Analyzer, Impedance Converters

#
# Active energy metering IC
#
CONFIG_ADE7854=y
# CONFIG_ADE7854_I2C is not set
# CONFIG_ADE7854_SPI is not set
# end of Active energy metering IC

#
# Resolver to digital converters
#
CONFIG_AD2S1210=y
# end of Resolver to digital converters
# end of IIO staging drivers

CONFIG_STAGING_MEDIA=y
CONFIG_VIDEO_IMX_MEDIA=y

#
# i.MX5/6/7/8 Media Sub devices
#
CONFIG_VIDEO_IMX_CSI=y
# CONFIG_VIDEO_IMX7_CSI is not set
# end of i.MX5/6/7/8 Media Sub devices

# CONFIG_VIDEO_MAX96712 is not set
CONFIG_VIDEO_MESON_VDEC=y
CONFIG_VIDEO_OMAP4=y
CONFIG_VIDEO_ROCKCHIP_VDEC=y
CONFIG_VIDEO_SUNXI=y
CONFIG_VIDEO_SUNXI_CEDRUS=y
# CONFIG_STAGING_MEDIA_DEPRECATED is not set
CONFIG_STAGING_BOARD=y
# CONFIG_MOST_COMPONENTS is not set
CONFIG_KS7010=y
CONFIG_BCM_VIDEOCORE=y
# CONFIG_BCM2835_VCHIQ is not set
# CONFIG_VIDEO_BCM2835 is not set
CONFIG_PI433=y
CONFIG_XIL_AXIS_FIFO=y
# CONFIG_FIELDBUS_DEV is not set
CONFIG_GOLDFISH=y
CONFIG_GOLDFISH_PIPE=y
CONFIG_CHROME_PLATFORMS=y
CONFIG_CROS_EC=y
# CONFIG_CROS_EC_I2C is not set
# CONFIG_CROS_EC_RPMSG is not set
CONFIG_CROS_EC_SPI=y
CONFIG_CROS_EC_PROTO=y
# CONFIG_CROS_KBD_LED_BACKLIGHT is not set
# CONFIG_MELLANOX_PLATFORM is not set
CONFIG_OLPC_XO175=y
# CONFIG_OLPC_XO175_EC is not set
CONFIG_SURFACE_PLATFORMS=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_LEGACY_CLK=y
# CONFIG_HWSPINLOCK is not set

#
# Clock Source drivers
#
CONFIG_TIMER_OF=y
CONFIG_TIMER_PROBE=y
CONFIG_CLKSRC_MMIO=y
CONFIG_BCM2835_TIMER=y
# CONFIG_BCM_KONA_TIMER is not set
# CONFIG_DAVINCI_TIMER is not set
# CONFIG_DIGICOLOR_TIMER is not set
# CONFIG_OMAP_DM_TIMER is not set
# CONFIG_DW_APB_TIMER is not set
# CONFIG_FTTMR010_TIMER is not set
CONFIG_IXP4XX_TIMER=y
# CONFIG_MESON6_TIMER is not set
# CONFIG_OWL_TIMER is not set
CONFIG_RDA_TIMER=y
CONFIG_SUN4I_TIMER=y
# CONFIG_TEGRA_TIMER is not set
# CONFIG_TEGRA186_TIMER is not set
CONFIG_VT8500_TIMER=y
# CONFIG_NPCM7XX_TIMER is not set
CONFIG_ASM9260_TIMER=y
# CONFIG_CLKSRC_DBX500_PRCMU is not set
# CONFIG_CLPS711X_TIMER is not set
CONFIG_MXS_TIMER=y
CONFIG_NSPIRE_TIMER=y
CONFIG_INTEGRATOR_AP_TIMER=y
# CONFIG_CLKSRC_PISTACHIO is not set
# CONFIG_CLKSRC_STM32_LP is not set
# CONFIG_ARMV7M_SYSTICK is not set
CONFIG_ATMEL_PIT=y
# CONFIG_ATMEL_ST is not set
CONFIG_CLKSRC_SAMSUNG_PWM=y
# CONFIG_FSL_FTM_TIMER is not set
CONFIG_OXNAS_RPS_TIMER=y
CONFIG_MTK_TIMER=y
CONFIG_CLKSRC_JCORE_PIT=y
# CONFIG_SH_TIMER_CMT is not set
# CONFIG_SH_TIMER_MTU2 is not set
# CONFIG_RENESAS_OSTM is not set
CONFIG_SH_TIMER_TMU=y
CONFIG_EM_TIMER_STI=y
# CONFIG_CLKSRC_PXA is not set
CONFIG_TIMER_IMX_SYS_CTR=y
# CONFIG_CLKSRC_ST_LPC is not set
# CONFIG_GXP_TIMER is not set
# CONFIG_MSC313E_TIMER is not set
CONFIG_MICROCHIP_PIT64B=y
# end of Clock Source drivers

CONFIG_MAILBOX=y
# CONFIG_IMX_MBOX is not set
CONFIG_PLATFORM_MHU=y
CONFIG_ARMADA_37XX_RWTM_MBOX=y
# CONFIG_ROCKCHIP_MBOX is not set
CONFIG_ALTERA_MBOX=y
CONFIG_MAILBOX_TEST=y
# CONFIG_POLARFIRE_SOC_MAILBOX is not set
# CONFIG_QCOM_APCS_IPC is not set
CONFIG_BCM_PDC_MBOX=y
CONFIG_STM32_IPCC=y
CONFIG_MTK_ADSP_MBOX=y
CONFIG_MTK_CMDQ_MBOX=y
CONFIG_SUN6I_MSGBOX=y
# CONFIG_SPRD_MBOX is not set
# CONFIG_QCOM_IPCC is not set

#
# Remoteproc drivers
#
CONFIG_REMOTEPROC=y
# CONFIG_REMOTEPROC_CDEV is not set
CONFIG_INGENIC_VPU_RPROC=y
# CONFIG_MTK_SCP is not set
# CONFIG_MESON_MX_AO_ARC_REMOTEPROC is not set
# CONFIG_RCAR_REMOTEPROC is not set
# end of Remoteproc drivers

#
# Rpmsg drivers
#
CONFIG_RPMSG=y
# CONFIG_RPMSG_CHAR is not set
# CONFIG_RPMSG_CTRL is not set
CONFIG_RPMSG_NS=y
CONFIG_RPMSG_QCOM_GLINK=y
CONFIG_RPMSG_QCOM_GLINK_RPM=y
CONFIG_RPMSG_VIRTIO=y
# end of Rpmsg drivers

# CONFIG_SOUNDWIRE is not set

#
# SOC (System On Chip) specific Drivers
#

#
# Amlogic SoC drivers
#
CONFIG_MESON_CANVAS=y
CONFIG_MESON_CLK_MEASURE=y
CONFIG_MESON_GX_SOCINFO=y
CONFIG_MESON_MX_SOCINFO=y
# end of Amlogic SoC drivers

#
# Apple SoC drivers
#
# CONFIG_APPLE_RTKIT is not set
# CONFIG_APPLE_SART is not set
# end of Apple SoC drivers

#
# ASPEED SoC drivers
#
# CONFIG_ASPEED_LPC_CTRL is not set
CONFIG_ASPEED_LPC_SNOOP=y
# CONFIG_ASPEED_UART_ROUTING is not set
CONFIG_ASPEED_P2A_CTRL=y
# CONFIG_ASPEED_SOCINFO is not set
# end of ASPEED SoC drivers

CONFIG_AT91_SOC_ID=y
CONFIG_AT91_SOC_SFR=y

#
# Broadcom SoC drivers
#
CONFIG_BCM2835_POWER=y
CONFIG_SOC_BCM63XX=y
# CONFIG_SOC_BRCMSTB is not set
CONFIG_BCM63XX_POWER=y
CONFIG_BCM_PMB=y
# end of Broadcom SoC drivers

#
# NXP/Freescale QorIQ SoC drivers
#
CONFIG_QUICC_ENGINE=y
CONFIG_UCC_SLOW=y
CONFIG_UCC=y
CONFIG_DPAA2_CONSOLE=y
# end of NXP/Freescale QorIQ SoC drivers

#
# fujitsu SoC drivers
#
# end of fujitsu SoC drivers

#
# i.MX SoC drivers
#
# CONFIG_SOC_IMX8M is not set
# CONFIG_SOC_IMX9 is not set
# end of i.MX SoC drivers

#
# IXP4xx SoC drivers
#
CONFIG_IXP4XX_QMGR=y
# CONFIG_IXP4XX_NPE is not set
# end of IXP4xx SoC drivers

#
# Enable LiteX SoC Builder specific drivers
#
CONFIG_LITEX=y
CONFIG_LITEX_SOC_CONTROLLER=y
# end of Enable LiteX SoC Builder specific drivers

#
# MediaTek SoC drivers
#
CONFIG_MTK_CMDQ=y
# CONFIG_MTK_DEVAPC is not set
CONFIG_MTK_INFRACFG=y
CONFIG_MTK_PMIC_WRAP=y
CONFIG_MTK_SCPSYS=y
CONFIG_MTK_MMSYS=y
# end of MediaTek SoC drivers

#
# Qualcomm SoC drivers
#
CONFIG_QCOM_GENI_SE=y
CONFIG_QCOM_GSBI=y
CONFIG_QCOM_LLCC=y
CONFIG_QCOM_PDR_HELPERS=y
CONFIG_QCOM_QMI_HELPERS=y
CONFIG_QCOM_RPMH=y
CONFIG_QCOM_SMD_RPM=y
# CONFIG_QCOM_SPM is not set
CONFIG_QCOM_WCNSS_CTRL=y
CONFIG_QCOM_APR=y
# CONFIG_QCOM_ICC_BWMON is not set
# end of Qualcomm SoC drivers

# CONFIG_SOC_RENESAS is not set
CONFIG_ROCKCHIP_GRF=y
CONFIG_ROCKCHIP_IODOMAIN=y
# CONFIG_SOC_SAMSUNG is not set
CONFIG_SUNXI_SRAM=y
# CONFIG_SOC_TEGRA20_VOLTAGE_COUPLER is not set
CONFIG_SOC_TEGRA30_VOLTAGE_COUPLER=y
CONFIG_SOC_TI=y
CONFIG_UX500_SOC_ID=y

#
# Xilinx SoC drivers
#
# end of Xilinx SoC drivers
# end of SOC (System On Chip) specific Drivers

# CONFIG_PM_DEVFREQ is not set
CONFIG_EXTCON=y

#
# Extcon Device Drivers
#
CONFIG_EXTCON_ADC_JACK=y
CONFIG_EXTCON_FSA9480=y
# CONFIG_EXTCON_GPIO is not set
# CONFIG_EXTCON_MAX14577 is not set
CONFIG_EXTCON_MAX3355=y
# CONFIG_EXTCON_MAX77693 is not set
CONFIG_EXTCON_MAX77843=y
CONFIG_EXTCON_MAX8997=y
CONFIG_EXTCON_PALMAS=y
CONFIG_EXTCON_PTN5150=y
CONFIG_EXTCON_QCOM_SPMI_MISC=y
CONFIG_EXTCON_RT8973A=y
# CONFIG_EXTCON_SM5502 is not set
CONFIG_EXTCON_USB_GPIO=y
# CONFIG_EXTCON_USBC_CROS_EC is not set
CONFIG_EXTCON_USBC_TUSB320=y
CONFIG_MEMORY=y
CONFIG_ATMEL_SDRAMC=y
# CONFIG_ATMEL_EBI is not set
# CONFIG_BRCMSTB_DPFE is not set
# CONFIG_BRCMSTB_MEMC is not set
CONFIG_BT1_L2_CTL=y
# CONFIG_TI_AEMIF is not set
# CONFIG_TI_EMIF is not set
CONFIG_OMAP_GPMC=y
# CONFIG_OMAP_GPMC_DEBUG is not set
CONFIG_MVEBU_DEVBUS=y
# CONFIG_FSL_CORENET_CF is not set
CONFIG_FSL_IFC=y
CONFIG_JZ4780_NEMC=y
# CONFIG_MTK_SMI is not set
# CONFIG_DA8XX_DDRCTL is not set
CONFIG_RENESAS_RPCIF=y
# CONFIG_STM32_FMC2_EBI is not set
# CONFIG_SAMSUNG_MC is not set
CONFIG_IIO=y
CONFIG_IIO_BUFFER=y
CONFIG_IIO_BUFFER_CB=y
CONFIG_IIO_BUFFER_DMA=y
CONFIG_IIO_BUFFER_DMAENGINE=y
CONFIG_IIO_BUFFER_HW_CONSUMER=y
CONFIG_IIO_KFIFO_BUF=y
CONFIG_IIO_TRIGGERED_BUFFER=y
# CONFIG_IIO_CONFIGFS is not set
CONFIG_IIO_TRIGGER=y
CONFIG_IIO_CONSUMERS_PER_TRIGGER=2
# CONFIG_IIO_SW_DEVICE is not set
# CONFIG_IIO_SW_TRIGGER is not set
CONFIG_IIO_TRIGGERED_EVENT=y

#
# Accelerometers
#
# CONFIG_ADIS16201 is not set
CONFIG_ADIS16209=y
# CONFIG_ADXL313_I2C is not set
# CONFIG_ADXL313_SPI is not set
CONFIG_ADXL345=y
# CONFIG_ADXL345_I2C is not set
CONFIG_ADXL345_SPI=y
# CONFIG_ADXL355_I2C is not set
# CONFIG_ADXL355_SPI is not set
# CONFIG_ADXL367_SPI is not set
# CONFIG_ADXL367_I2C is not set
CONFIG_ADXL372=y
CONFIG_ADXL372_SPI=y
# CONFIG_ADXL372_I2C is not set
# CONFIG_BMA180 is not set
CONFIG_BMA220=y
# CONFIG_BMA400 is not set
CONFIG_BMC150_ACCEL=y
CONFIG_BMC150_ACCEL_I2C=y
CONFIG_BMC150_ACCEL_SPI=y
# CONFIG_BMI088_ACCEL is not set
CONFIG_DA280=y
CONFIG_DA311=y
CONFIG_DMARD06=y
# CONFIG_DMARD09 is not set
CONFIG_DMARD10=y
CONFIG_FXLS8962AF=y
# CONFIG_FXLS8962AF_I2C is not set
CONFIG_FXLS8962AF_SPI=y
# CONFIG_HID_SENSOR_ACCEL_3D is not set
# CONFIG_KXSD9 is not set
CONFIG_KXCJK1013=y
CONFIG_MC3230=y
CONFIG_MMA7455=y
CONFIG_MMA7455_I2C=y
# CONFIG_MMA7455_SPI is not set
CONFIG_MMA7660=y
CONFIG_MMA8452=y
CONFIG_MMA9551_CORE=y
CONFIG_MMA9551=y
CONFIG_MMA9553=y
# CONFIG_MSA311 is not set
CONFIG_MXC4005=y
CONFIG_MXC6255=y
# CONFIG_SCA3000 is not set
# CONFIG_SCA3300 is not set
# CONFIG_STK8312 is not set
CONFIG_STK8BA50=y
# end of Accelerometers

#
# Analog to digital converters
#
CONFIG_AD_SIGMA_DELTA=y
CONFIG_AD7091R5=y
# CONFIG_AD7124 is not set
CONFIG_AD7192=y
CONFIG_AD7266=y
CONFIG_AD7280=y
CONFIG_AD7291=y
CONFIG_AD7292=y
CONFIG_AD7298=y
# CONFIG_AD7476 is not set
CONFIG_AD7606=y
# CONFIG_AD7606_IFACE_PARALLEL is not set
CONFIG_AD7606_IFACE_SPI=y
# CONFIG_AD7766 is not set
CONFIG_AD7768_1=y
CONFIG_AD7780=y
# CONFIG_AD7791 is not set
CONFIG_AD7793=y
CONFIG_AD7887=y
# CONFIG_AD7923 is not set
CONFIG_AD7949=y
# CONFIG_AD799X is not set
CONFIG_AD9467=y
CONFIG_ADI_AXI_ADC=y
CONFIG_AT91_ADC=y
# CONFIG_AT91_SAMA5D2_ADC is not set
# CONFIG_AXP20X_ADC is not set
# CONFIG_AXP288_ADC is not set
CONFIG_BCM_IPROC_ADC=y
# CONFIG_BERLIN2_ADC is not set
# CONFIG_CC10001_ADC is not set
# CONFIG_ENVELOPE_DETECTOR is not set
CONFIG_EXYNOS_ADC=y
CONFIG_MXS_LRADC_ADC=y
# CONFIG_HI8435 is not set
# CONFIG_HX711 is not set
CONFIG_INA2XX_ADC=y
# CONFIG_INGENIC_ADC is not set
CONFIG_IMX7D_ADC=y
# CONFIG_IMX8QXP_ADC is not set
CONFIG_LPC18XX_ADC=y
# CONFIG_LPC32XX_ADC is not set
# CONFIG_LTC2471 is not set
CONFIG_LTC2485=y
# CONFIG_LTC2496 is not set
# CONFIG_LTC2497 is not set
CONFIG_MAX1027=y
# CONFIG_MAX11100 is not set
CONFIG_MAX1118=y
# CONFIG_MAX11205 is not set
CONFIG_MAX1241=y
CONFIG_MAX1363=y
# CONFIG_MAX9611 is not set
# CONFIG_MCP320X is not set
CONFIG_MCP3422=y
# CONFIG_MCP3911 is not set
CONFIG_MEDIATEK_MT6360_ADC=y
# CONFIG_MEDIATEK_MT6577_AUXADC is not set
CONFIG_MEN_Z188_ADC=y
CONFIG_MP2629_ADC=y
# CONFIG_NAU7802 is not set
CONFIG_NPCM_ADC=y
CONFIG_PALMAS_GPADC=y
CONFIG_QCOM_VADC_COMMON=y
# CONFIG_QCOM_SPMI_RRADC is not set
# CONFIG_QCOM_SPMI_IADC is not set
CONFIG_QCOM_SPMI_VADC=y
CONFIG_QCOM_SPMI_ADC5=y
CONFIG_RCAR_GYRO_ADC=y
CONFIG_ROCKCHIP_SARADC=y
# CONFIG_RICHTEK_RTQ6056 is not set
CONFIG_RZG2L_ADC=y
CONFIG_SC27XX_ADC=y
# CONFIG_SPEAR_ADC is not set
CONFIG_SD_ADC_MODULATOR=y
# CONFIG_STM32_ADC_CORE is not set
CONFIG_STM32_DFSDM_CORE=y
CONFIG_STM32_DFSDM_ADC=y
CONFIG_TI_ADC081C=y
# CONFIG_TI_ADC0832 is not set
# CONFIG_TI_ADC084S021 is not set
# CONFIG_TI_ADC12138 is not set
CONFIG_TI_ADC108S102=y
CONFIG_TI_ADC128S052=y
CONFIG_TI_ADC161S626=y
CONFIG_TI_ADS1015=y
# CONFIG_TI_ADS7950 is not set
CONFIG_TI_ADS8344=y
CONFIG_TI_ADS8688=y
CONFIG_TI_ADS124S08=y
CONFIG_TI_ADS131E08=y
# CONFIG_TI_AM335X_ADC is not set
CONFIG_TI_TLC4541=y
CONFIG_TI_TSC2046=y
CONFIG_TWL4030_MADC=y
CONFIG_TWL6030_GPADC=y
# CONFIG_VF610_ADC is not set
# CONFIG_XILINX_XADC is not set
# CONFIG_XILINX_AMS is not set
# end of Analog to digital converters

#
# Analog to digital and digital to analog converters
#
# CONFIG_AD74413R is not set
# end of Analog to digital and digital to analog converters

#
# Analog Front Ends
#
CONFIG_IIO_RESCALE=y
# end of Analog Front Ends

#
# Amplifiers
#
CONFIG_AD8366=y
# CONFIG_ADA4250 is not set
CONFIG_HMC425=y
# end of Amplifiers

#
# Capacitance to digital converters
#
CONFIG_AD7150=y
CONFIG_AD7746=y
# end of Capacitance to digital converters

#
# Chemical Sensors
#
CONFIG_ATLAS_PH_SENSOR=y
CONFIG_ATLAS_EZO_SENSOR=y
# CONFIG_BME680 is not set
CONFIG_CCS811=y
CONFIG_IAQCORE=y
# CONFIG_PMS7003 is not set
CONFIG_SCD30_CORE=y
# CONFIG_SCD30_I2C is not set
# CONFIG_SCD30_SERIAL is not set
# CONFIG_SCD4X is not set
CONFIG_SENSIRION_SGP30=y
# CONFIG_SENSIRION_SGP40 is not set
CONFIG_SPS30=y
# CONFIG_SPS30_I2C is not set
CONFIG_SPS30_SERIAL=y
# CONFIG_SENSEAIR_SUNRISE_CO2 is not set
CONFIG_VZ89X=y
# end of Chemical Sensors

#
# Hid Sensor IIO Common
#
CONFIG_HID_SENSOR_IIO_COMMON=y
CONFIG_HID_SENSOR_IIO_TRIGGER=y
# end of Hid Sensor IIO Common

CONFIG_IIO_MS_SENSORS_I2C=y

#
# IIO SCMI Sensors
#
CONFIG_IIO_SCMI=y
# end of IIO SCMI Sensors

#
# SSP Sensor Common
#
# CONFIG_IIO_SSP_SENSORHUB is not set
# end of SSP Sensor Common

CONFIG_IIO_ST_SENSORS_I2C=y
CONFIG_IIO_ST_SENSORS_SPI=y
CONFIG_IIO_ST_SENSORS_CORE=y

#
# Digital to analog converters
#
# CONFIG_AD3552R is not set
# CONFIG_AD5064 is not set
CONFIG_AD5360=y
CONFIG_AD5380=y
CONFIG_AD5421=y
CONFIG_AD5446=y
# CONFIG_AD5449 is not set
CONFIG_AD5592R_BASE=y
CONFIG_AD5592R=y
CONFIG_AD5593R=y
# CONFIG_AD5504 is not set
CONFIG_AD5624R_SPI=y
# CONFIG_LTC2688 is not set
CONFIG_AD5686=y
# CONFIG_AD5686_SPI is not set
CONFIG_AD5696_I2C=y
# CONFIG_AD5755 is not set
# CONFIG_AD5758 is not set
CONFIG_AD5761=y
CONFIG_AD5764=y
CONFIG_AD5766=y
CONFIG_AD5770R=y
CONFIG_AD5791=y
# CONFIG_AD7293 is not set
CONFIG_AD7303=y
CONFIG_AD8801=y
# CONFIG_DPOT_DAC is not set
CONFIG_DS4424=y
CONFIG_LPC18XX_DAC=y
CONFIG_LTC1660=y
# CONFIG_LTC2632 is not set
CONFIG_M62332=y
CONFIG_MAX517=y
# CONFIG_MAX5821 is not set
CONFIG_MCP4725=y
CONFIG_MCP4922=y
# CONFIG_STM32_DAC is not set
CONFIG_TI_DAC082S085=y
CONFIG_TI_DAC5571=y
# CONFIG_TI_DAC7311 is not set
CONFIG_TI_DAC7612=y
# CONFIG_VF610_DAC is not set
# end of Digital to analog converters

#
# IIO dummy driver
#
# end of IIO dummy driver

#
# Filters
#
# end of Filters

#
# Frequency Synthesizers DDS/PLL
#

#
# Clock Generator/Distribution
#
CONFIG_AD9523=y
# end of Clock Generator/Distribution

#
# Phase-Locked Loop (PLL) frequency synthesizers
#
# CONFIG_ADF4350 is not set
CONFIG_ADF4371=y
# CONFIG_ADMV4420 is not set
# end of Phase-Locked Loop (PLL) frequency synthesizers
# end of Frequency Synthesizers DDS/PLL

#
# Digital gyroscope sensors
#
CONFIG_ADIS16080=y
CONFIG_ADIS16130=y
CONFIG_ADIS16136=y
CONFIG_ADIS16260=y
CONFIG_ADXRS290=y
CONFIG_ADXRS450=y
CONFIG_BMG160=y
CONFIG_BMG160_I2C=y
CONFIG_BMG160_SPI=y
CONFIG_FXAS21002C=y
CONFIG_FXAS21002C_I2C=y
CONFIG_FXAS21002C_SPI=y
# CONFIG_HID_SENSOR_GYRO_3D is not set
CONFIG_MPU3050=y
CONFIG_MPU3050_I2C=y
CONFIG_IIO_ST_GYRO_3AXIS=y
CONFIG_IIO_ST_GYRO_I2C_3AXIS=y
CONFIG_IIO_ST_GYRO_SPI_3AXIS=y
CONFIG_ITG3200=y
# end of Digital gyroscope sensors

#
# Health Sensors
#

#
# Heart Rate Monitors
#
# CONFIG_AFE4403 is not set
CONFIG_AFE4404=y
CONFIG_MAX30100=y
# CONFIG_MAX30102 is not set
# end of Heart Rate Monitors
# end of Health Sensors

#
# Humidity sensors
#
CONFIG_AM2315=y
CONFIG_DHT11=y
# CONFIG_HDC100X is not set
CONFIG_HDC2010=y
CONFIG_HID_SENSOR_HUMIDITY=y
# CONFIG_HTS221 is not set
# CONFIG_HTU21 is not set
# CONFIG_SI7005 is not set
CONFIG_SI7020=y
# end of Humidity sensors

#
# Inertial measurement units
#
CONFIG_ADIS16400=y
CONFIG_ADIS16460=y
# CONFIG_ADIS16475 is not set
CONFIG_ADIS16480=y
CONFIG_BMI160=y
CONFIG_BMI160_I2C=y
# CONFIG_BMI160_SPI is not set
# CONFIG_BOSCH_BNO055_SERIAL is not set
# CONFIG_BOSCH_BNO055_I2C is not set
CONFIG_FXOS8700=y
CONFIG_FXOS8700_I2C=y
CONFIG_FXOS8700_SPI=y
CONFIG_KMX61=y
CONFIG_INV_ICM42600=y
# CONFIG_INV_ICM42600_I2C is not set
CONFIG_INV_ICM42600_SPI=y
CONFIG_INV_MPU6050_IIO=y
CONFIG_INV_MPU6050_I2C=y
CONFIG_INV_MPU6050_SPI=y
CONFIG_IIO_ST_LSM6DSX=y
CONFIG_IIO_ST_LSM6DSX_I2C=y
CONFIG_IIO_ST_LSM6DSX_SPI=y
CONFIG_IIO_ST_LSM6DSX_I3C=y
# end of Inertial measurement units

CONFIG_IIO_ADIS_LIB=y
CONFIG_IIO_ADIS_LIB_BUFFER=y

#
# Light sensors
#
CONFIG_ADJD_S311=y
CONFIG_ADUX1020=y
# CONFIG_AL3010 is not set
CONFIG_AL3320A=y
CONFIG_APDS9300=y
CONFIG_APDS9960=y
# CONFIG_AS73211 is not set
CONFIG_BH1750=y
CONFIG_BH1780=y
CONFIG_CM32181=y
CONFIG_CM3232=y
CONFIG_CM3323=y
# CONFIG_CM3605 is not set
CONFIG_CM36651=y
CONFIG_GP2AP002=y
# CONFIG_GP2AP020A00F is not set
# CONFIG_IQS621_ALS is not set
# CONFIG_SENSORS_ISL29018 is not set
CONFIG_SENSORS_ISL29028=y
CONFIG_ISL29125=y
CONFIG_HID_SENSOR_ALS=y
# CONFIG_HID_SENSOR_PROX is not set
CONFIG_JSA1212=y
# CONFIG_RPR0521 is not set
CONFIG_SENSORS_LM3533=y
CONFIG_LTR501=y
# CONFIG_LTRF216A is not set
CONFIG_LV0104CS=y
# CONFIG_MAX44000 is not set
# CONFIG_MAX44009 is not set
# CONFIG_NOA1305 is not set
CONFIG_OPT3001=y
CONFIG_PA12203001=y
# CONFIG_SI1133 is not set
CONFIG_SI1145=y
# CONFIG_STK3310 is not set
# CONFIG_ST_UVIS25 is not set
# CONFIG_TCS3414 is not set
# CONFIG_TCS3472 is not set
# CONFIG_SENSORS_TSL2563 is not set
# CONFIG_TSL2583 is not set
CONFIG_TSL2591=y
CONFIG_TSL2772=y
CONFIG_TSL4531=y
# CONFIG_US5182D is not set
CONFIG_VCNL4000=y
CONFIG_VCNL4035=y
CONFIG_VEML6030=y
CONFIG_VEML6070=y
# CONFIG_VL6180 is not set
CONFIG_ZOPT2201=y
# end of Light sensors

#
# Magnetometer sensors
#
# CONFIG_AK8974 is not set
CONFIG_AK8975=y
CONFIG_AK09911=y
CONFIG_BMC150_MAGN=y
CONFIG_BMC150_MAGN_I2C=y
# CONFIG_BMC150_MAGN_SPI is not set
CONFIG_MAG3110=y
CONFIG_HID_SENSOR_MAGNETOMETER_3D=y
# CONFIG_MMC35240 is not set
CONFIG_IIO_ST_MAGN_3AXIS=y
CONFIG_IIO_ST_MAGN_I2C_3AXIS=y
CONFIG_IIO_ST_MAGN_SPI_3AXIS=y
CONFIG_SENSORS_HMC5843=y
CONFIG_SENSORS_HMC5843_I2C=y
CONFIG_SENSORS_HMC5843_SPI=y
CONFIG_SENSORS_RM3100=y
# CONFIG_SENSORS_RM3100_I2C is not set
CONFIG_SENSORS_RM3100_SPI=y
# CONFIG_YAMAHA_YAS530 is not set
# end of Magnetometer sensors

#
# Multiplexers
#
CONFIG_IIO_MUX=y
# end of Multiplexers

#
# Inclinometer sensors
#
# CONFIG_HID_SENSOR_INCLINOMETER_3D is not set
# CONFIG_HID_SENSOR_DEVICE_ROTATION is not set
# end of Inclinometer sensors

#
# Triggers - standalone
#
CONFIG_IIO_INTERRUPT_TRIGGER=y
CONFIG_IIO_STM32_LPTIMER_TRIGGER=y
CONFIG_IIO_STM32_TIMER_TRIGGER=y
CONFIG_IIO_SYSFS_TRIGGER=y
# end of Triggers - standalone

#
# Linear and angular position sensors
#
# CONFIG_IQS624_POS is not set
CONFIG_HID_SENSOR_CUSTOM_INTEL_HINGE=y
# end of Linear and angular position sensors

#
# Digital potentiometers
#
CONFIG_AD5110=y
CONFIG_AD5272=y
CONFIG_DS1803=y
CONFIG_MAX5432=y
# CONFIG_MAX5481 is not set
# CONFIG_MAX5487 is not set
CONFIG_MCP4018=y
# CONFIG_MCP4131 is not set
CONFIG_MCP4531=y
# CONFIG_MCP41010 is not set
# CONFIG_TPL0102 is not set
# end of Digital potentiometers

#
# Digital potentiostats
#
CONFIG_LMP91000=y
# end of Digital potentiostats

#
# Pressure sensors
#
CONFIG_ABP060MG=y
# CONFIG_BMP280 is not set
CONFIG_DLHL60D=y
CONFIG_DPS310=y
# CONFIG_HID_SENSOR_PRESS is not set
CONFIG_HP03=y
CONFIG_ICP10100=y
# CONFIG_MPL115_I2C is not set
# CONFIG_MPL115_SPI is not set
CONFIG_MPL3115=y
CONFIG_MS5611=y
# CONFIG_MS5611_I2C is not set
CONFIG_MS5611_SPI=y
CONFIG_MS5637=y
CONFIG_IIO_ST_PRESS=y
CONFIG_IIO_ST_PRESS_I2C=y
CONFIG_IIO_ST_PRESS_SPI=y
CONFIG_T5403=y
CONFIG_HP206C=y
# CONFIG_ZPA2326 is not set
# end of Pressure sensors

#
# Lightning sensors
#
CONFIG_AS3935=y
# end of Lightning sensors

#
# Proximity and distance sensors
#
CONFIG_CROS_EC_MKBP_PROXIMITY=y
CONFIG_ISL29501=y
# CONFIG_LIDAR_LITE_V2 is not set
CONFIG_MB1232=y
CONFIG_PING=y
CONFIG_RFD77402=y
CONFIG_SRF04=y
CONFIG_SX_COMMON=y
CONFIG_SX9310=y
CONFIG_SX9324=y
# CONFIG_SX9360 is not set
CONFIG_SX9500=y
CONFIG_SRF08=y
CONFIG_VCNL3020=y
CONFIG_VL53L0X_I2C=y
# end of Proximity and distance sensors

#
# Resolver to digital converters
#
CONFIG_AD2S90=y
CONFIG_AD2S1200=y
# end of Resolver to digital converters

#
# Temperature sensors
#
CONFIG_IQS620AT_TEMP=y
CONFIG_LTC2983=y
CONFIG_MAXIM_THERMOCOUPLE=y
# CONFIG_HID_SENSOR_TEMP is not set
CONFIG_MLX90614=y
# CONFIG_MLX90632 is not set
CONFIG_TMP006=y
# CONFIG_TMP007 is not set
CONFIG_TMP117=y
# CONFIG_TSYS01 is not set
CONFIG_TSYS02D=y
# CONFIG_MAX31856 is not set
# CONFIG_MAX31865 is not set
# end of Temperature sensors

# CONFIG_PWM is not set

#
# IRQ chip support
#
CONFIG_IRQCHIP=y
CONFIG_AL_FIC=y
CONFIG_MADERA_IRQ=y
# CONFIG_JCORE_AIC is not set
CONFIG_RENESAS_INTC_IRQPIN=y
# CONFIG_RENESAS_IRQC is not set
CONFIG_RENESAS_RZA1_IRQC=y
# CONFIG_RENESAS_RZG2L_IRQC is not set
# CONFIG_SL28CPLD_INTC is not set
CONFIG_TS4800_IRQ=y
# CONFIG_XILINX_INTC is not set
# CONFIG_INGENIC_TCU_IRQ is not set
# CONFIG_IRQ_UNIPHIER_AIDET is not set
# CONFIG_MESON_IRQ_GPIO is not set
# CONFIG_IMX_IRQSTEER is not set
# CONFIG_IMX_INTMUX is not set
# CONFIG_IMX_MU_MSI is not set
CONFIG_EXYNOS_IRQ_COMBINER=y
# CONFIG_MST_IRQ is not set
# CONFIG_MCHP_EIC is not set
# CONFIG_SUNPLUS_SP7021_INTC is not set
# end of IRQ chip support

# CONFIG_IPACK_BUS is not set
CONFIG_RESET_CONTROLLER=y
# CONFIG_RESET_A10SR is not set
# CONFIG_RESET_ATH79 is not set
# CONFIG_RESET_AXS10X is not set
# CONFIG_RESET_BCM6345 is not set
CONFIG_RESET_BERLIN=y
CONFIG_RESET_BRCMSTB=y
CONFIG_RESET_BRCMSTB_RESCAL=y
CONFIG_RESET_HSDK=y
# CONFIG_RESET_IMX7 is not set
CONFIG_RESET_INTEL_GW=y
# CONFIG_RESET_K210 is not set
CONFIG_RESET_LANTIQ=y
# CONFIG_RESET_LPC18XX is not set
CONFIG_RESET_MCHP_SPARX5=y
# CONFIG_RESET_MESON is not set
CONFIG_RESET_MESON_AUDIO_ARB=y
# CONFIG_RESET_NPCM is not set
CONFIG_RESET_PISTACHIO=y
# CONFIG_RESET_QCOM_AOSS is not set
CONFIG_RESET_QCOM_PDC=y
CONFIG_RESET_RASPBERRYPI=y
CONFIG_RESET_RZG2L_USBPHY_CTRL=y
CONFIG_RESET_SCMI=y
CONFIG_RESET_SIMPLE=y
# CONFIG_RESET_SOCFPGA is not set
# CONFIG_RESET_STARFIVE_JH7100 is not set
# CONFIG_RESET_SUNPLUS is not set
# CONFIG_RESET_SUNXI is not set
# CONFIG_RESET_TI_SCI is not set
CONFIG_RESET_TI_SYSCON=y
# CONFIG_RESET_TI_TPS380X is not set
# CONFIG_RESET_TN48M_CPLD is not set
# CONFIG_RESET_UNIPHIER is not set
CONFIG_RESET_UNIPHIER_GLUE=y
# CONFIG_RESET_ZYNQ is not set
CONFIG_COMMON_RESET_HI3660=y
CONFIG_COMMON_RESET_HI6220=y

#
# PHY Subsystem
#
CONFIG_GENERIC_PHY=y
CONFIG_GENERIC_PHY_MIPI_DPHY=y
# CONFIG_PHY_LPC18XX_USB_OTG is not set
CONFIG_PHY_PISTACHIO_USB=y
# CONFIG_PHY_XGENE is not set
CONFIG_USB_LGM_PHY=y
CONFIG_PHY_CAN_TRANSCEIVER=y
CONFIG_PHY_SUN4I_USB=y
CONFIG_PHY_SUN9I_USB=y
# CONFIG_PHY_SUN50I_USB3 is not set
# CONFIG_PHY_MESON8_HDMI_TX is not set
CONFIG_PHY_MESON8B_USB2=y
CONFIG_PHY_MESON_GXL_USB2=y
# CONFIG_PHY_MESON_G12A_MIPI_DPHY_ANALOG is not set
# CONFIG_PHY_MESON_G12A_USB2 is not set
CONFIG_PHY_MESON_G12A_USB3_PCIE=y
CONFIG_PHY_MESON_AXG_PCIE=y
CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG=y
# CONFIG_PHY_MESON_AXG_MIPI_DPHY is not set

#
# PHY drivers for Broadcom platforms
#
CONFIG_PHY_BCM63XX_USBH=y
CONFIG_PHY_CYGNUS_PCIE=y
CONFIG_PHY_BCM_SR_USB=y
CONFIG_BCM_KONA_USB2_PHY=y
CONFIG_PHY_BCM_NS_USB2=y
# CONFIG_PHY_BCM_NS_USB3 is not set
# CONFIG_PHY_NS2_PCIE is not set
# CONFIG_PHY_NS2_USB_DRD is not set
# CONFIG_PHY_BRCM_SATA is not set
CONFIG_PHY_BRCM_USB=y
# CONFIG_PHY_BCM_SR_PCIE is not set
# end of PHY drivers for Broadcom platforms

CONFIG_PHY_CADENCE_DPHY=y
# CONFIG_PHY_CADENCE_DPHY_RX is not set
CONFIG_PHY_CADENCE_SALVO=y
# CONFIG_PHY_FSL_IMX8MQ_USB is not set
# CONFIG_PHY_MIXEL_LVDS_PHY is not set
CONFIG_PHY_MIXEL_MIPI_DPHY=y
# CONFIG_PHY_FSL_IMX8M_PCIE is not set
# CONFIG_PHY_FSL_LYNX_28G is not set
CONFIG_PHY_HI6220_USB=y
CONFIG_PHY_HI3660_USB=y
# CONFIG_PHY_HI3670_USB is not set
# CONFIG_PHY_HI3670_PCIE is not set
# CONFIG_PHY_HISTB_COMBPHY is not set
CONFIG_PHY_HISI_INNO_USB2=y
CONFIG_PHY_INGENIC_USB=y
CONFIG_PHY_LANTIQ_VRX200_PCIE=y
CONFIG_PHY_LANTIQ_RCU_USB2=y
# CONFIG_ARMADA375_USBCLUSTER_PHY is not set
CONFIG_PHY_BERLIN_SATA=y
# CONFIG_PHY_BERLIN_USB is not set
CONFIG_PHY_MVEBU_A3700_UTMI=y
CONFIG_PHY_MVEBU_A38X_COMPHY=y
CONFIG_PHY_MVEBU_CP110_UTMI=y
CONFIG_PHY_PXA_28NM_HSIC=y
CONFIG_PHY_PXA_28NM_USB2=y
# CONFIG_PHY_PXA_USB is not set
CONFIG_PHY_MMP3_USB=y
CONFIG_PHY_MMP3_HSIC=y
# CONFIG_PHY_MTK_PCIE is not set
# CONFIG_PHY_MTK_TPHY is not set
CONFIG_PHY_MTK_UFS=y
CONFIG_PHY_MTK_XSPHY=y
# CONFIG_PHY_MTK_DP is not set
CONFIG_PHY_SPARX5_SERDES=y
# CONFIG_PHY_LAN966X_SERDES is not set
CONFIG_PHY_CPCAP_USB=y
CONFIG_PHY_MAPPHONE_MDM6600=y
CONFIG_PHY_OCELOT_SERDES=y
# CONFIG_PHY_ATH79_USB is not set
# CONFIG_PHY_QCOM_IPQ4019_USB is not set
CONFIG_PHY_QCOM_QUSB2=y
CONFIG_PHY_QCOM_USB_HS=y
CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2=y
CONFIG_PHY_QCOM_USB_HSIC=y
CONFIG_PHY_QCOM_USB_HS_28NM=y
# CONFIG_PHY_QCOM_USB_SS is not set
CONFIG_PHY_QCOM_IPQ806X_USB=y
# CONFIG_PHY_MT7621_PCI is not set
CONFIG_PHY_RALINK_USB=y
CONFIG_PHY_RCAR_GEN3_USB3=y
CONFIG_PHY_ROCKCHIP_DPHY_RX0=y
# CONFIG_PHY_ROCKCHIP_INNO_CSIDPHY is not set
CONFIG_PHY_ROCKCHIP_INNO_DSIDPHY=y
CONFIG_PHY_ROCKCHIP_PCIE=y
# CONFIG_PHY_ROCKCHIP_SNPS_PCIE3 is not set
# CONFIG_PHY_ROCKCHIP_TYPEC is not set
CONFIG_PHY_EXYNOS_DP_VIDEO=y
CONFIG_PHY_EXYNOS_MIPI_VIDEO=y
# CONFIG_PHY_EXYNOS_PCIE is not set
CONFIG_PHY_SAMSUNG_UFS=y
# CONFIG_PHY_SAMSUNG_USB2 is not set
CONFIG_PHY_UNIPHIER_USB2=y
CONFIG_PHY_UNIPHIER_USB3=y
CONFIG_PHY_UNIPHIER_PCIE=y
CONFIG_PHY_UNIPHIER_AHCI=y
CONFIG_PHY_ST_SPEAR1310_MIPHY=y
CONFIG_PHY_ST_SPEAR1340_MIPHY=y
CONFIG_PHY_STIH407_USB=y
# CONFIG_PHY_SUNPLUS_USB is not set
# CONFIG_PHY_TEGRA194_P2U is not set
CONFIG_PHY_DA8XX_USB=y
# CONFIG_PHY_DM816X_USB is not set
CONFIG_OMAP_CONTROL_PHY=y
# CONFIG_TI_PIPE3 is not set
# CONFIG_PHY_TUSB1210 is not set
CONFIG_PHY_INTEL_KEEMBAY_EMMC=y
# CONFIG_PHY_INTEL_KEEMBAY_USB is not set
CONFIG_PHY_INTEL_LGM_COMBO=y
CONFIG_PHY_INTEL_LGM_EMMC=y
# CONFIG_PHY_INTEL_THUNDERBAY_EMMC is not set
# CONFIG_PHY_XILINX_ZYNQMP is not set
# end of PHY Subsystem

# CONFIG_POWERCAP is not set
CONFIG_MCB=y
# CONFIG_MCB_LPC is not set
CONFIG_RAS=y

#
# Android
#
# end of Android

CONFIG_DAX=y
CONFIG_NVMEM=y
CONFIG_NVMEM_SYSFS=y
# CONFIG_NVMEM_APPLE_EFUSES is not set
CONFIG_NVMEM_BCM_OCOTP=y
CONFIG_NVMEM_BRCM_NVRAM=y
CONFIG_NVMEM_IMX_IIM=y
# CONFIG_NVMEM_IMX_OCOTP is not set
# CONFIG_NVMEM_JZ4780_EFUSE is not set
# CONFIG_NVMEM_LAN9662_OTPC is not set
# CONFIG_NVMEM_LAYERSCAPE_SFP is not set
CONFIG_NVMEM_LPC18XX_EEPROM=y
CONFIG_NVMEM_LPC18XX_OTP=y
# CONFIG_NVMEM_MESON_MX_EFUSE is not set
# CONFIG_NVMEM_MICROCHIP_OTPC is not set
# CONFIG_NVMEM_MTK_EFUSE is not set
# CONFIG_NVMEM_MXS_OCOTP is not set
CONFIG_NVMEM_NINTENDO_OTP=y
# CONFIG_NVMEM_QCOM_QFPROM is not set
# CONFIG_NVMEM_RAVE_SP_EEPROM is not set
# CONFIG_NVMEM_RMEM is not set
# CONFIG_NVMEM_ROCKCHIP_EFUSE is not set
# CONFIG_NVMEM_ROCKCHIP_OTP is not set
# CONFIG_NVMEM_SC27XX_EFUSE is not set
CONFIG_NVMEM_SNVS_LPGPR=y
CONFIG_NVMEM_SPMI_SDAM=y
# CONFIG_NVMEM_SPRD_EFUSE is not set
CONFIG_NVMEM_STM32_ROMEM=y
# CONFIG_NVMEM_SUNPLUS_OCOTP is not set
# CONFIG_NVMEM_U_BOOT_ENV is not set
# CONFIG_NVMEM_UNIPHIER_EFUSE is not set
CONFIG_NVMEM_VF610_OCOTP=y

#
# HW tracing support
#
# CONFIG_STM is not set
CONFIG_INTEL_TH=y
CONFIG_INTEL_TH_GTH=y
CONFIG_INTEL_TH_MSU=y
CONFIG_INTEL_TH_PTI=y
CONFIG_INTEL_TH_DEBUG=y
# end of HW tracing support

# CONFIG_FPGA is not set
CONFIG_FSI=y
CONFIG_FSI_NEW_DEV_NODE=y
CONFIG_FSI_MASTER_GPIO=y
# CONFIG_FSI_MASTER_HUB is not set
CONFIG_FSI_MASTER_ASPEED=y
CONFIG_FSI_SCOM=y
CONFIG_FSI_SBEFIFO=y
# CONFIG_FSI_OCC is not set
# CONFIG_TEE is not set
CONFIG_MULTIPLEXER=y

#
# Multiplexer drivers
#
CONFIG_MUX_ADG792A=y
CONFIG_MUX_ADGS1408=y
CONFIG_MUX_GPIO=y
CONFIG_MUX_MMIO=y
# end of Multiplexer drivers

# CONFIG_SIOX is not set
CONFIG_SLIMBUS=y
CONFIG_SLIM_QCOM_CTRL=y
# CONFIG_SLIM_QCOM_NGD_CTRL is not set
CONFIG_INTERCONNECT=y
CONFIG_INTERCONNECT_IMX=y
CONFIG_INTERCONNECT_IMX8MM=y
CONFIG_INTERCONNECT_IMX8MN=y
CONFIG_INTERCONNECT_IMX8MQ=y
# CONFIG_INTERCONNECT_IMX8MP is not set
CONFIG_INTERCONNECT_QCOM_OSM_L3=y
CONFIG_INTERCONNECT_SAMSUNG=y
CONFIG_INTERCONNECT_EXYNOS=y
# CONFIG_COUNTER is not set
CONFIG_MOST=y
CONFIG_MOST_USB_HDM=y
CONFIG_MOST_CDEV=y
# CONFIG_PECI is not set
# CONFIG_HTE is not set
# end of Device Drivers

#
# File systems
#
CONFIG_VALIDATE_FS_PARSER=y
CONFIG_FS_IOMAP=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
# CONFIG_EXT2_FS_POSIX_ACL is not set
# CONFIG_EXT2_FS_SECURITY is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_EXT4_FS=y
CONFIG_EXT4_FS_POSIX_ACL=y
CONFIG_EXT4_FS_SECURITY=y
CONFIG_EXT4_DEBUG=y
CONFIG_JBD2=y
# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
CONFIG_JFS_FS=y
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
CONFIG_JFS_DEBUG=y
# CONFIG_JFS_STATISTICS is not set
CONFIG_XFS_FS=y
CONFIG_XFS_SUPPORT_V4=y
CONFIG_XFS_QUOTA=y
# CONFIG_XFS_POSIX_ACL is not set
CONFIG_XFS_RT=y
# CONFIG_XFS_ONLINE_SCRUB is not set
# CONFIG_XFS_WARN is not set
# CONFIG_XFS_DEBUG is not set
# CONFIG_GFS2_FS is not set
CONFIG_BTRFS_FS=y
# CONFIG_BTRFS_FS_POSIX_ACL is not set
CONFIG_BTRFS_FS_CHECK_INTEGRITY=y
# CONFIG_BTRFS_FS_RUN_SANITY_TESTS is not set
# CONFIG_BTRFS_DEBUG is not set
# CONFIG_BTRFS_ASSERT is not set
# CONFIG_BTRFS_FS_REF_VERIFY is not set
CONFIG_NILFS2_FS=y
CONFIG_F2FS_FS=y
# CONFIG_F2FS_STAT_FS is not set
CONFIG_F2FS_FS_XATTR=y
# CONFIG_F2FS_FS_POSIX_ACL is not set
# CONFIG_F2FS_FS_SECURITY is not set
# CONFIG_F2FS_CHECK_FS is not set
CONFIG_F2FS_FAULT_INJECTION=y
# CONFIG_F2FS_FS_COMPRESSION is not set
# CONFIG_F2FS_IOSTAT is not set
CONFIG_ZONEFS_FS=y
CONFIG_FS_POSIX_ACL=y
CONFIG_EXPORTFS=y
# CONFIG_EXPORTFS_BLOCK_OPS is not set
CONFIG_FILE_LOCKING=y
# CONFIG_FS_ENCRYPTION is not set
# CONFIG_FS_VERITY is not set
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_INOTIFY_USER=y
# CONFIG_FANOTIFY is not set
# CONFIG_QUOTA is not set
CONFIG_QUOTA_NETLINK_INTERFACE=y
CONFIG_QUOTACTL=y
CONFIG_AUTOFS4_FS=y
CONFIG_AUTOFS_FS=y
# CONFIG_FUSE_FS is not set
CONFIG_OVERLAY_FS=y
CONFIG_OVERLAY_FS_REDIRECT_DIR=y
# CONFIG_OVERLAY_FS_REDIRECT_ALWAYS_FOLLOW is not set
# CONFIG_OVERLAY_FS_INDEX is not set
CONFIG_OVERLAY_FS_METACOPY=y

#
# Caches
#
CONFIG_NETFS_SUPPORT=y
CONFIG_NETFS_STATS=y
CONFIG_FSCACHE=y
CONFIG_FSCACHE_STATS=y
# CONFIG_FSCACHE_DEBUG is not set
# CONFIG_CACHEFILES is not set
# end of Caches

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
# CONFIG_JOLIET is not set
CONFIG_ZISOFS=y
CONFIG_UDF_FS=y
# end of CD-ROM/DVD Filesystems

#
# DOS/FAT/EXFAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
# CONFIG_VFAT_FS is not set
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_EXFAT_FS=y
CONFIG_EXFAT_DEFAULT_IOCHARSET="utf8"
CONFIG_NTFS_FS=y
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y
# CONFIG_NTFS3_FS is not set
# end of DOS/FAT/EXFAT/NT Filesystems

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
# CONFIG_PROC_CHILDREN is not set
CONFIG_KERNFS=y
CONFIG_SYSFS=y
CONFIG_CONFIGFS_FS=y
# end of Pseudo filesystems

CONFIG_MISC_FILESYSTEMS=y
CONFIG_ORANGEFS_FS=y
# CONFIG_ADFS_FS is not set
CONFIG_AFFS_FS=y
# CONFIG_ECRYPT_FS is not set
CONFIG_HFS_FS=y
CONFIG_HFSPLUS_FS=y
# CONFIG_BEFS_FS is not set
CONFIG_BFS_FS=y
CONFIG_EFS_FS=y
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=0
# CONFIG_JFFS2_FS_WRITEBUFFER is not set
# CONFIG_JFFS2_SUMMARY is not set
# CONFIG_JFFS2_FS_XATTR is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
CONFIG_CRAMFS=y
CONFIG_CRAMFS_BLOCKDEV=y
CONFIG_CRAMFS_MTD=y
CONFIG_SQUASHFS=y
CONFIG_SQUASHFS_FILE_CACHE=y
# CONFIG_SQUASHFS_FILE_DIRECT is not set
CONFIG_SQUASHFS_DECOMP_SINGLE=y
# CONFIG_SQUASHFS_DECOMP_MULTI is not set
# CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU is not set
# CONFIG_SQUASHFS_XATTR is not set
# CONFIG_SQUASHFS_ZLIB is not set
# CONFIG_SQUASHFS_LZ4 is not set
# CONFIG_SQUASHFS_LZO is not set
CONFIG_SQUASHFS_XZ=y
# CONFIG_SQUASHFS_ZSTD is not set
CONFIG_SQUASHFS_4K_DEVBLK_SIZE=y
CONFIG_SQUASHFS_EMBEDDED=y
CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
CONFIG_MINIX_FS_NATIVE_ENDIAN=y
CONFIG_OMFS_FS=y
CONFIG_HPFS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX6FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_PSTORE=y
CONFIG_PSTORE_DEFAULT_KMSG_BYTES=10240
CONFIG_PSTORE_DEFLATE_COMPRESS=y
# CONFIG_PSTORE_LZO_COMPRESS is not set
CONFIG_PSTORE_LZ4_COMPRESS=y
# CONFIG_PSTORE_LZ4HC_COMPRESS is not set
CONFIG_PSTORE_842_COMPRESS=y
CONFIG_PSTORE_ZSTD_COMPRESS=y
CONFIG_PSTORE_COMPRESS=y
# CONFIG_PSTORE_DEFLATE_COMPRESS_DEFAULT is not set
CONFIG_PSTORE_LZ4_COMPRESS_DEFAULT=y
# CONFIG_PSTORE_842_COMPRESS_DEFAULT is not set
# CONFIG_PSTORE_ZSTD_COMPRESS_DEFAULT is not set
CONFIG_PSTORE_COMPRESS_DEFAULT="lz4"
# CONFIG_PSTORE_CONSOLE is not set
# CONFIG_PSTORE_PMSG is not set
# CONFIG_PSTORE_RAM is not set
CONFIG_PSTORE_ZONE=y
CONFIG_PSTORE_BLK=y
CONFIG_PSTORE_BLK_BLKDEV=""
CONFIG_PSTORE_BLK_KMSG_SIZE=64
CONFIG_PSTORE_BLK_MAX_REASON=2
CONFIG_SYSV_FS=y
CONFIG_UFS_FS=y
CONFIG_UFS_FS_WRITE=y
# CONFIG_UFS_DEBUG is not set
# CONFIG_EROFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
CONFIG_NLS_CODEPAGE_775=y
# CONFIG_NLS_CODEPAGE_850 is not set
CONFIG_NLS_CODEPAGE_852=y
# CONFIG_NLS_CODEPAGE_855 is not set
CONFIG_NLS_CODEPAGE_857=y
# CONFIG_NLS_CODEPAGE_860 is not set
CONFIG_NLS_CODEPAGE_861=y
CONFIG_NLS_CODEPAGE_862=y
CONFIG_NLS_CODEPAGE_863=y
CONFIG_NLS_CODEPAGE_864=y
# CONFIG_NLS_CODEPAGE_865 is not set
CONFIG_NLS_CODEPAGE_866=y
CONFIG_NLS_CODEPAGE_869=y
CONFIG_NLS_CODEPAGE_936=y
CONFIG_NLS_CODEPAGE_950=y
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
CONFIG_NLS_CODEPAGE_874=y
CONFIG_NLS_ISO8859_8=y
# CONFIG_NLS_CODEPAGE_1250 is not set
CONFIG_NLS_CODEPAGE_1251=y
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
CONFIG_NLS_ISO8859_7=y
CONFIG_NLS_ISO8859_9=y
CONFIG_NLS_ISO8859_13=y
CONFIG_NLS_ISO8859_14=y
CONFIG_NLS_ISO8859_15=y
CONFIG_NLS_KOI8_R=y
CONFIG_NLS_KOI8_U=y
CONFIG_NLS_MAC_ROMAN=y
CONFIG_NLS_MAC_CELTIC=y
CONFIG_NLS_MAC_CENTEURO=y
CONFIG_NLS_MAC_CROATIAN=y
CONFIG_NLS_MAC_CYRILLIC=y
CONFIG_NLS_MAC_GAELIC=y
CONFIG_NLS_MAC_GREEK=y
CONFIG_NLS_MAC_ICELAND=y
CONFIG_NLS_MAC_INUIT=y
CONFIG_NLS_MAC_ROMANIAN=y
CONFIG_NLS_MAC_TURKISH=y
CONFIG_NLS_UTF8=y
# CONFIG_UNICODE is not set
CONFIG_IO_WQ=y
# end of File systems

#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_REQUEST_CACHE=y
# CONFIG_PERSISTENT_KEYRINGS is not set
CONFIG_TRUSTED_KEYS=y
CONFIG_TRUSTED_KEYS_TPM=y
CONFIG_ENCRYPTED_KEYS=y
# CONFIG_USER_DECRYPTED_DATA is not set
CONFIG_KEY_DH_OPERATIONS=y
CONFIG_SECURITY_DMESG_RESTRICT=y
CONFIG_SECURITY=y
CONFIG_SECURITYFS=y
CONFIG_SECURITY_NETWORK=y
CONFIG_SECURITY_PATH=y
CONFIG_HAVE_HARDENED_USERCOPY_ALLOCATOR=y
CONFIG_HARDENED_USERCOPY=y
# CONFIG_STATIC_USERMODEHELPER is not set
CONFIG_SECURITY_TOMOYO=y
CONFIG_SECURITY_TOMOYO_MAX_ACCEPT_ENTRY=2048
CONFIG_SECURITY_TOMOYO_MAX_AUDIT_LOG=1024
CONFIG_SECURITY_TOMOYO_OMIT_USERSPACE_LOADER=y
# CONFIG_SECURITY_TOMOYO_INSECURE_BUILTIN_SETTING is not set
CONFIG_SECURITY_APPARMOR=y
# CONFIG_SECURITY_APPARMOR_DEBUG is not set
CONFIG_SECURITY_APPARMOR_INTROSPECT_POLICY=y
# CONFIG_SECURITY_APPARMOR_HASH is not set
CONFIG_SECURITY_APPARMOR_EXPORT_BINARY=y
CONFIG_SECURITY_APPARMOR_PARANOID_LOAD=y
CONFIG_SECURITY_LOADPIN=y
CONFIG_SECURITY_LOADPIN_ENFORCE=y
# CONFIG_SECURITY_LOADPIN_VERITY is not set
CONFIG_SECURITY_YAMA=y
# CONFIG_SECURITY_SAFESETID is not set
CONFIG_SECURITY_LOCKDOWN_LSM=y
# CONFIG_SECURITY_LOCKDOWN_LSM_EARLY is not set
# CONFIG_LOCK_DOWN_KERNEL_FORCE_NONE is not set
CONFIG_LOCK_DOWN_KERNEL_FORCE_INTEGRITY=y
# CONFIG_LOCK_DOWN_KERNEL_FORCE_CONFIDENTIALITY is not set
CONFIG_SECURITY_LANDLOCK=y
# CONFIG_INTEGRITY is not set
CONFIG_DEFAULT_SECURITY_TOMOYO=y
# CONFIG_DEFAULT_SECURITY_APPARMOR is not set
# CONFIG_DEFAULT_SECURITY_DAC is not set
CONFIG_LSM="landlock,lockdown,yama,loadpin,safesetid,integrity,tomoyo,bpf"

#
# Kernel hardening options
#

#
# Memory initialization
#
CONFIG_CC_HAS_AUTO_VAR_INIT_PATTERN=y
CONFIG_CC_HAS_AUTO_VAR_INIT_ZERO_BARE=y
CONFIG_CC_HAS_AUTO_VAR_INIT_ZERO=y
# CONFIG_INIT_STACK_NONE is not set
# CONFIG_INIT_STACK_ALL_PATTERN is not set
CONFIG_INIT_STACK_ALL_ZERO=y
CONFIG_INIT_ON_ALLOC_DEFAULT_ON=y
CONFIG_INIT_ON_FREE_DEFAULT_ON=y
CONFIG_CC_HAS_ZERO_CALL_USED_REGS=y
CONFIG_ZERO_CALL_USED_REGS=y
# end of Memory initialization

CONFIG_RANDSTRUCT_NONE=y
# end of Kernel hardening options
# end of Security options

CONFIG_XOR_BLOCKS=y
CONFIG_ASYNC_CORE=y
CONFIG_ASYNC_MEMCPY=y
CONFIG_ASYNC_XOR=y
CONFIG_ASYNC_PQ=y
CONFIG_ASYNC_RAID6_RECOV=y
CONFIG_ASYNC_TX_DISABLE_PQ_VAL_DMA=y
CONFIG_ASYNC_TX_DISABLE_XOR_VAL_DMA=y
CONFIG_CRYPTO=y

#
# Crypto core or helper
#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_SKCIPHER=y
CONFIG_CRYPTO_SKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_RNG_DEFAULT=y
CONFIG_CRYPTO_AKCIPHER2=y
CONFIG_CRYPTO_AKCIPHER=y
CONFIG_CRYPTO_KPP2=y
CONFIG_CRYPTO_KPP=y
CONFIG_CRYPTO_ACOMP2=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_USER is not set
CONFIG_CRYPTO_MANAGER_DISABLE_TESTS=y
CONFIG_CRYPTO_GF128MUL=y
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_NULL2=y
CONFIG_CRYPTO_CRYPTD=y
CONFIG_CRYPTO_AUTHENC=y
CONFIG_CRYPTO_ENGINE=y
# end of Crypto core or helper

#
# Public-key cryptography
#
CONFIG_CRYPTO_RSA=y
CONFIG_CRYPTO_DH=y
# CONFIG_CRYPTO_DH_RFC7919_GROUPS is not set
CONFIG_CRYPTO_ECC=y
CONFIG_CRYPTO_ECDH=y
CONFIG_CRYPTO_ECDSA=y
# CONFIG_CRYPTO_ECRDSA is not set
# CONFIG_CRYPTO_SM2 is not set
CONFIG_CRYPTO_CURVE25519=y
# end of Public-key cryptography

#
# Block ciphers
#
CONFIG_CRYPTO_AES=y
# CONFIG_CRYPTO_AES_TI is not set
CONFIG_CRYPTO_ANUBIS=y
# CONFIG_CRYPTO_ARIA is not set
# CONFIG_CRYPTO_BLOWFISH is not set
CONFIG_CRYPTO_CAMELLIA=y
CONFIG_CRYPTO_CAST_COMMON=y
CONFIG_CRYPTO_CAST5=y
CONFIG_CRYPTO_CAST6=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_FCRYPT=y
CONFIG_CRYPTO_KHAZAD=y
CONFIG_CRYPTO_SEED=y
CONFIG_CRYPTO_SERPENT=y
CONFIG_CRYPTO_SM4=y
CONFIG_CRYPTO_SM4_GENERIC=y
CONFIG_CRYPTO_TEA=y
CONFIG_CRYPTO_TWOFISH=y
CONFIG_CRYPTO_TWOFISH_COMMON=y
# end of Block ciphers

#
# Length-preserving ciphers and modes
#
CONFIG_CRYPTO_ADIANTUM=y
# CONFIG_CRYPTO_ARC4 is not set
CONFIG_CRYPTO_CHACHA20=y
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_CFB=y
CONFIG_CRYPTO_CTR=y
CONFIG_CRYPTO_CTS=y
CONFIG_CRYPTO_ECB=y
# CONFIG_CRYPTO_HCTR2 is not set
CONFIG_CRYPTO_KEYWRAP=y
CONFIG_CRYPTO_LRW=y
CONFIG_CRYPTO_OFB=y
# CONFIG_CRYPTO_PCBC is not set
CONFIG_CRYPTO_XTS=y
CONFIG_CRYPTO_NHPOLY1305=y
# end of Length-preserving ciphers and modes

#
# AEAD (authenticated encryption with associated data) ciphers
#
# CONFIG_CRYPTO_AEGIS128 is not set
CONFIG_CRYPTO_CHACHA20POLY1305=y
# CONFIG_CRYPTO_CCM is not set
CONFIG_CRYPTO_GCM=y
# CONFIG_CRYPTO_SEQIV is not set
CONFIG_CRYPTO_ECHAINIV=y
CONFIG_CRYPTO_ESSIV=y
# end of AEAD (authenticated encryption with associated data) ciphers

#
# Hashes, digests, and MACs
#
CONFIG_CRYPTO_BLAKE2B=y
CONFIG_CRYPTO_CMAC=y
CONFIG_CRYPTO_GHASH=y
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=y
CONFIG_CRYPTO_POLY1305=y
CONFIG_CRYPTO_RMD160=y
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_SHA512=y
CONFIG_CRYPTO_SHA3=y
CONFIG_CRYPTO_SM3=y
CONFIG_CRYPTO_SM3_GENERIC=y
CONFIG_CRYPTO_STREEBOG=y
# CONFIG_CRYPTO_VMAC is not set
# CONFIG_CRYPTO_WP512 is not set
CONFIG_CRYPTO_XCBC=y
CONFIG_CRYPTO_XXHASH=y
# end of Hashes, digests, and MACs

#
# CRCs (cyclic redundancy checks)
#
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_CRC32=y
CONFIG_CRYPTO_CRCT10DIF=y
CONFIG_CRYPTO_CRC64_ROCKSOFT=y
# end of CRCs (cyclic redundancy checks)

#
# Compression
#
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_LZO=y
CONFIG_CRYPTO_842=y
CONFIG_CRYPTO_LZ4=y
# CONFIG_CRYPTO_LZ4HC is not set
CONFIG_CRYPTO_ZSTD=y
# end of Compression

#
# Random number generation
#
CONFIG_CRYPTO_ANSI_CPRNG=y
CONFIG_CRYPTO_DRBG_MENU=y
CONFIG_CRYPTO_DRBG_HMAC=y
# CONFIG_CRYPTO_DRBG_HASH is not set
# CONFIG_CRYPTO_DRBG_CTR is not set
CONFIG_CRYPTO_DRBG=y
CONFIG_CRYPTO_JITTERENTROPY=y
CONFIG_CRYPTO_KDF800108_CTR=y
# end of Random number generation

#
# Userspace interface
#
CONFIG_CRYPTO_USER_API=y
# CONFIG_CRYPTO_USER_API_HASH is not set
CONFIG_CRYPTO_USER_API_SKCIPHER=y
# CONFIG_CRYPTO_USER_API_RNG is not set
CONFIG_CRYPTO_USER_API_AEAD=y
CONFIG_CRYPTO_USER_API_ENABLE_OBSOLETE=y
# end of Userspace interface

CONFIG_CRYPTO_HASH_INFO=y
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_ALLWINNER is not set
CONFIG_CRYPTO_DEV_EXYNOS_RNG=y
# CONFIG_CRYPTO_DEV_S5P is not set
CONFIG_CRYPTO_DEV_ATMEL_AUTHENC=y
CONFIG_CRYPTO_DEV_ATMEL_AES=y
CONFIG_CRYPTO_DEV_ATMEL_TDES=y
CONFIG_CRYPTO_DEV_ATMEL_SHA=y
CONFIG_CRYPTO_DEV_ATMEL_I2C=y
CONFIG_CRYPTO_DEV_ATMEL_ECC=y
CONFIG_CRYPTO_DEV_ATMEL_SHA204A=y
CONFIG_CRYPTO_DEV_QCE=y
CONFIG_CRYPTO_DEV_QCE_SKCIPHER=y
# CONFIG_CRYPTO_DEV_QCE_ENABLE_ALL is not set
CONFIG_CRYPTO_DEV_QCE_ENABLE_SKCIPHER=y
# CONFIG_CRYPTO_DEV_QCE_ENABLE_SHA is not set
# CONFIG_CRYPTO_DEV_QCE_ENABLE_AEAD is not set
CONFIG_CRYPTO_DEV_QCE_SW_MAX_LEN=512
CONFIG_CRYPTO_DEV_QCOM_RNG=y
CONFIG_CRYPTO_DEV_IMGTEC_HASH=y
CONFIG_CRYPTO_DEV_ZYNQMP_AES=y
# CONFIG_CRYPTO_DEV_ZYNQMP_SHA3 is not set
# CONFIG_CRYPTO_DEV_VIRTIO is not set
CONFIG_CRYPTO_DEV_SAFEXCEL=y
CONFIG_CRYPTO_DEV_CCREE=y
# CONFIG_CRYPTO_DEV_HISI_SEC is not set
# CONFIG_CRYPTO_DEV_AMLOGIC_GXL is not set
CONFIG_CRYPTO_DEV_SA2UL=y
# CONFIG_CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 is not set
# CONFIG_CRYPTO_DEV_KEEMBAY_OCS_ECC is not set
CONFIG_CRYPTO_DEV_KEEMBAY_OCS_HCU=y
# CONFIG_CRYPTO_DEV_KEEMBAY_OCS_HCU_HMAC_SHA224 is not set
# CONFIG_CRYPTO_DEV_ASPEED is not set
CONFIG_ASYMMETRIC_KEY_TYPE=y
CONFIG_ASYMMETRIC_PUBLIC_KEY_SUBTYPE=y
CONFIG_X509_CERTIFICATE_PARSER=y
# CONFIG_PKCS8_PRIVATE_KEY_PARSER is not set
CONFIG_PKCS7_MESSAGE_PARSER=y
# CONFIG_PKCS7_TEST_KEY is not set
# CONFIG_SIGNED_PE_FILE_VERIFICATION is not set
# CONFIG_FIPS_SIGNATURE_SELFTEST is not set

#
# Certificates for signature checking
#
CONFIG_SYSTEM_TRUSTED_KEYRING=y
CONFIG_SYSTEM_TRUSTED_KEYS=""
CONFIG_SYSTEM_EXTRA_CERTIFICATE=y
CONFIG_SYSTEM_EXTRA_CERTIFICATE_SIZE=4096
# CONFIG_SECONDARY_TRUSTED_KEYRING is not set
# CONFIG_SYSTEM_BLACKLIST_KEYRING is not set
# end of Certificates for signature checking

#
# Library routines
#
CONFIG_RAID6_PQ=y
CONFIG_RAID6_PQ_BENCHMARK=y
CONFIG_LINEAR_RANGES=y
CONFIG_PACKING=y
CONFIG_BITREVERSE=y
CONFIG_GENERIC_STRNCPY_FROM_USER=y
CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GENERIC_NET_UTILS=y
CONFIG_CORDIC=y
CONFIG_PRIME_NUMBERS=y
CONFIG_RATIONAL=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_IOMAP=y
CONFIG_STMP_DEVICE=y

#
# Crypto library routines
#
CONFIG_CRYPTO_LIB_UTILS=y
CONFIG_CRYPTO_LIB_AES=y
CONFIG_CRYPTO_LIB_ARC4=y
CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y
CONFIG_CRYPTO_LIB_CHACHA_GENERIC=y
CONFIG_CRYPTO_LIB_CHACHA=y
CONFIG_CRYPTO_LIB_CURVE25519_GENERIC=y
CONFIG_CRYPTO_LIB_CURVE25519=y
CONFIG_CRYPTO_LIB_DES=y
CONFIG_CRYPTO_LIB_POLY1305_RSIZE=1
CONFIG_CRYPTO_LIB_POLY1305_GENERIC=y
CONFIG_CRYPTO_LIB_POLY1305=y
CONFIG_CRYPTO_LIB_CHACHA20POLY1305=y
CONFIG_CRYPTO_LIB_SHA1=y
CONFIG_CRYPTO_LIB_SHA256=y
# end of Crypto library routines

CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
CONFIG_CRC_T10DIF=y
CONFIG_CRC64_ROCKSOFT=y
CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
# CONFIG_CRC32_SELFTEST is not set
CONFIG_CRC32_SLICEBY8=y
# CONFIG_CRC32_SLICEBY4 is not set
# CONFIG_CRC32_SARWATE is not set
# CONFIG_CRC32_BIT is not set
CONFIG_CRC64=y
CONFIG_CRC4=y
CONFIG_CRC7=y
CONFIG_LIBCRC32C=y
CONFIG_CRC8=y
CONFIG_XXHASH=y
CONFIG_AUDIT_GENERIC=y
# CONFIG_RANDOM32_SELFTEST is not set
CONFIG_842_COMPRESS=y
CONFIG_842_DECOMPRESS=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_LZ4_COMPRESS=y
CONFIG_LZ4_DECOMPRESS=y
CONFIG_ZSTD_COMMON=y
CONFIG_ZSTD_COMPRESS=y
CONFIG_ZSTD_DECOMPRESS=y
CONFIG_XZ_DEC=y
CONFIG_XZ_DEC_X86=y
CONFIG_XZ_DEC_POWERPC=y
CONFIG_XZ_DEC_IA64=y
CONFIG_XZ_DEC_ARM=y
CONFIG_XZ_DEC_ARMTHUMB=y
CONFIG_XZ_DEC_SPARC=y
# CONFIG_XZ_DEC_MICROLZMA is not set
CONFIG_XZ_DEC_BCJ=y
# CONFIG_XZ_DEC_TEST is not set
CONFIG_DECOMPRESS_LZMA=y
CONFIG_DECOMPRESS_XZ=y
CONFIG_DECOMPRESS_LZO=y
CONFIG_DECOMPRESS_ZSTD=y
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_REED_SOLOMON=y
CONFIG_REED_SOLOMON_DEC8=y
CONFIG_BCH=y
CONFIG_BCH_CONST_PARAMS=y
CONFIG_ASSOCIATIVE_ARRAY=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_DMA=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_ARCH_HAS_SYNC_DMA_FOR_DEVICE=y
CONFIG_DMA_NONCOHERENT_MMAP=y
CONFIG_DMA_API_DEBUG=y
# CONFIG_DMA_API_DEBUG_SG is not set
# CONFIG_DMA_MAP_BENCHMARK is not set
CONFIG_SGL_ALLOC=y
CONFIG_DQL=y
CONFIG_GLOB=y
CONFIG_GLOB_SELFTEST=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
CONFIG_CLZ_TAB=y
CONFIG_IRQ_POLL=y
CONFIG_MPILIB=y
CONFIG_LIBFDT=y
CONFIG_OID_REGISTRY=y
CONFIG_SG_SPLIT=y
CONFIG_SG_POOL=y
CONFIG_UACCESS_MEMCPY=y
CONFIG_SBITMAP=y
CONFIG_PARMAN=y
CONFIG_OBJAGG=y
# end of Library routines

CONFIG_ASN1_ENCODER=y

#
# Kernel hacking
#

#
# printk and dmesg options
#
# CONFIG_PRINTK_TIME is not set
CONFIG_PRINTK_CALLER=y
# CONFIG_STACKTRACE_BUILD_ID is not set
CONFIG_CONSOLE_LOGLEVEL_DEFAULT=7
CONFIG_CONSOLE_LOGLEVEL_QUIET=4
CONFIG_MESSAGE_LOGLEVEL_DEFAULT=4
CONFIG_DYNAMIC_DEBUG=y
CONFIG_DYNAMIC_DEBUG_CORE=y
# CONFIG_SYMBOLIC_ERRNAME is not set
CONFIG_DEBUG_BUGVERBOSE=y
# end of printk and dmesg options

# CONFIG_DEBUG_KERNEL is not set

#
# Compile-time checks and compiler options
#
CONFIG_AS_HAS_NON_CONST_LEB128=y
CONFIG_FRAME_WARN=1024
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_HEADERS_INSTALL is not set
CONFIG_DEBUG_SECTION_MISMATCH=y
CONFIG_SECTION_MISMATCH_WARN_ONLY=y
# end of Compile-time checks and compiler options

#
# Generic Kernel Debugging Instruments
#
CONFIG_MAGIC_SYSRQ=y
CONFIG_MAGIC_SYSRQ_DEFAULT_ENABLE=0x1
CONFIG_MAGIC_SYSRQ_SERIAL=y
CONFIG_MAGIC_SYSRQ_SERIAL_SEQUENCE=""
CONFIG_DEBUG_FS=y
# CONFIG_DEBUG_FS_ALLOW_ALL is not set
CONFIG_DEBUG_FS_DISALLOW_MOUNT=y
# CONFIG_DEBUG_FS_ALLOW_NONE is not set
CONFIG_UBSAN=y
CONFIG_CC_HAS_UBSAN_BOUNDS=y
# CONFIG_UBSAN_BOUNDS is not set
CONFIG_UBSAN_SHIFT=y
# CONFIG_UBSAN_DIV_ZERO is not set
CONFIG_UBSAN_UNREACHABLE=y
# CONFIG_UBSAN_BOOL is not set
# CONFIG_UBSAN_ENUM is not set
CONFIG_HAVE_KCSAN_COMPILER=y
# end of Generic Kernel Debugging Instruments

#
# Networking Debugging
#
# end of Networking Debugging

#
# Memory Debugging
#
# CONFIG_PAGE_EXTENSION is not set
CONFIG_SLUB_DEBUG=y
# CONFIG_SLUB_DEBUG_ON is not set
# CONFIG_PAGE_POISONING is not set
# CONFIG_SHRINKER_DEBUG is not set
CONFIG_DEBUG_MEMORY_INIT=y
CONFIG_CC_HAS_WORKING_NOSANITIZE_ADDRESS=y
# end of Memory Debugging

#
# Debug Oops, Lockups and Hangs
#
CONFIG_PANIC_ON_OOPS=y
CONFIG_PANIC_ON_OOPS_VALUE=1
CONFIG_PANIC_TIMEOUT=0
# end of Debug Oops, Lockups and Hangs

#
# Scheduler Debugging
#
# end of Scheduler Debugging

# CONFIG_DEBUG_TIMEKEEPING is not set

#
# Lock Debugging (spinlocks, mutexes, etc...)
#
CONFIG_WW_MUTEX_SELFTEST=y
# end of Lock Debugging (spinlocks, mutexes, etc...)

CONFIG_DEBUG_IRQFLAGS=y
CONFIG_WARN_ALL_UNSEEDED_RANDOM=y
CONFIG_HAVE_DEBUG_BUGVERBOSE=y

#
# Debug kernel data structures
#
CONFIG_DEBUG_LIST=y
CONFIG_BUG_ON_DATA_CORRUPTION=y
# end of Debug kernel data structures

#
# RCU Debugging
#
CONFIG_RCU_CPU_STALL_TIMEOUT=21
CONFIG_RCU_EXP_CPU_STALL_TIMEOUT=0
# end of RCU Debugging

# CONFIG_SAMPLES is not set
# CONFIG_STRICT_DEVMEM is not set

#
# m68k Debugging
#
# CONFIG_BOOTPARAM is not set
# CONFIG_FULLDEBUG is not set
# CONFIG_HIGHPROFILE is not set
CONFIG_NO_KERNEL_MSG=y
# CONFIG_BDM_DISABLE is not set
# end of m68k Debugging

#
# Kernel Testing and Coverage
#
# CONFIG_KUNIT is not set
CONFIG_CC_HAS_SANCOV_TRACE_PC=y
# CONFIG_RUNTIME_TESTING_MENU is not set
# end of Kernel Testing and Coverage

#
# Rust hacking
#
# end of Rust hacking

# CONFIG_WARN_MISSING_DOCUMENTS is not set
CONFIG_WARN_ABI_ERRORS=y
# end of Kernel hacking

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA
  2022-12-10 22:46 ` [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA Piergiorgio Beruto
  2022-12-11 12:05   ` kernel test robot
@ 2022-12-11 12:23   ` Russell King (Oracle)
  2022-12-11 19:03     ` Piergiorgio Beruto
  1 sibling, 1 reply; 13+ messages in thread
From: Russell King (Oracle) @ 2022-12-11 12:23 UTC (permalink / raw)
  To: Piergiorgio Beruto
  Cc: Andrew Lunn, Heiner Kallweit, David S. Miller, Eric Dumazet,
	Jakub Kicinski, Paolo Abeni, linux-kernel, netdev,
	Oleksij Rempel

On Sat, Dec 10, 2022 at 11:46:39PM +0100, Piergiorgio Beruto wrote:
> This patch adds the required connection between netlink ethtool and
> phylib to resolve PLCA get/set config and get status messages.
> 
> Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
> ---
>  drivers/net/phy/phy.c        | 175 +++++++++++++++++++++++++++++++++++
>  drivers/net/phy/phy_device.c |   3 +
>  include/linux/phy.h          |   7 ++
>  3 files changed, 185 insertions(+)
> 
> diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> index e5b6cb1a77f9..40d90ed2f0fb 100644
> --- a/drivers/net/phy/phy.c
> +++ b/drivers/net/phy/phy.c
> @@ -543,6 +543,181 @@ int phy_ethtool_get_stats(struct phy_device *phydev,
>  }
>  EXPORT_SYMBOL(phy_ethtool_get_stats);
>  
> +/**
> + * phy_ethtool_get_plca_cfg - Get PLCA RS configuration
> + *

You shouldn't have an empty line in the comment here

> + * @phydev: the phy_device struct
> + * @plca_cfg: where to store the retrieved configuration

Maybe have an empty line, followed by a bit of text describing what this
function does and the return codes it generates?

> + */
> +int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
> +			     struct phy_plca_cfg *plca_cfg)
> +{
> +	int ret;
> +
> +	if (!phydev->drv) {
> +		ret = -EIO;
> +		goto out;
> +	}
> +
> +	if (!phydev->drv->get_plca_cfg) {
> +		ret = -EOPNOTSUPP;
> +		goto out;
> +	}
> +
> +	memset(plca_cfg, 0xFF, sizeof(*plca_cfg));
> +
> +	mutex_lock(&phydev->lock);

Maybe move the memset() and mutex_lock() before the first if() statement
above? Maybe the memset() should be done by plca_get_cfg_prepare_data()?
Wouldn't all implementations need to memset this to 0xff?

Also, lower-case 0xff please.

> +	ret = phydev->drv->get_plca_cfg(phydev, plca_cfg);
> +
> +	if (ret)
> +		goto out_drv;
> +
> +out_drv:

This if() and out_drv label seems unused (although with the above
suggested change, you will need to move the "out" label here.)

> +	mutex_unlock(&phydev->lock);
> +out:
> +	return ret;
> +}
> +
> +/**
> + * phy_ethtool_set_plca_cfg - Set PLCA RS configuration
> + *
> + * @phydev: the phy_device struct
> + * @extack: extack for reporting useful error messages
> + * @plca_cfg: new PLCA configuration to apply
> + */
> +int phy_ethtool_set_plca_cfg(struct phy_device *phydev,
> +			     const struct phy_plca_cfg *plca_cfg,
> +			     struct netlink_ext_ack *extack)
> +{
> +	int ret;
> +	struct phy_plca_cfg *curr_plca_cfg = 0;

Unnecessary initialiser. Also, reverse Christmas-tree please.

> +
> +	if (!phydev->drv) {
> +		ret = -EIO;
> +		goto out;
> +	}
> +
> +	if (!phydev->drv->set_plca_cfg ||
> +	    !phydev->drv->get_plca_cfg) {
> +		ret = -EOPNOTSUPP;
> +		goto out;
> +	}
> +
> +	curr_plca_cfg = kmalloc(sizeof(*curr_plca_cfg), GFP_KERNEL);

What if kmalloc() returns NULL?

> +	memset(curr_plca_cfg, 0xFF, sizeof(*curr_plca_cfg));
> +
> +	mutex_lock(&phydev->lock);

Consider moving the above three to the beginning of the function so
phydev->drv is checked under the mutex.

> +
> +	ret = phydev->drv->get_plca_cfg(phydev, curr_plca_cfg);
> +	if (ret)
> +		goto out_drv;
> +
> +	if (curr_plca_cfg->enabled < 0 && plca_cfg->enabled >= 0) {
> +		NL_SET_ERR_MSG(extack,
> +			       "PHY does not support changing the PLCA 'enable' attribute");
> +		ret = -EINVAL;
> +		goto out_drv;
> +	}
> +
> +	if (curr_plca_cfg->node_id < 0 && plca_cfg->node_id >= 0) {
> +		NL_SET_ERR_MSG(extack,
> +			       "PHY does not support changing the PLCA 'local node ID' attribute");
> +		ret = -EINVAL;
> +		goto out_drv;
> +	}
> +
> +	if (curr_plca_cfg->node_cnt < 0 && plca_cfg->node_cnt >= 0) {
> +		NL_SET_ERR_MSG(extack,
> +			       "PHY does not support changing the PLCA 'node count' attribute");
> +		ret = -EINVAL;
> +		goto out_drv;
> +	}
> +
> +	if (curr_plca_cfg->to_tmr < 0 && plca_cfg->to_tmr >= 0) {
> +		NL_SET_ERR_MSG(extack,
> +			       "PHY does not support changing the PLCA 'TO timer' attribute");
> +		ret = -EINVAL;
> +		goto out_drv;
> +	}
> +
> +	if (curr_plca_cfg->burst_cnt < 0 && plca_cfg->burst_cnt >= 0) {
> +		NL_SET_ERR_MSG(extack,
> +			       "PHY does not support changing the PLCA 'burst count' attribute");
> +		ret = -EINVAL;
> +		goto out_drv;
> +	}
> +
> +	if (curr_plca_cfg->burst_tmr < 0 && plca_cfg->burst_tmr >= 0) {
> +		NL_SET_ERR_MSG(extack,
> +			       "PHY does not support changing the PLCA 'burst timer' attribute");
> +		ret = -EINVAL;
> +		goto out_drv;
> +	}
> +
> +	// if enabling PLCA, perform additional sanity checks
> +	if (plca_cfg->enabled > 0) {
> +		if (!linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT,
> +				       phydev->advertising)) {
> +			ret = -EOPNOTSUPP;
> +			NL_SET_ERR_MSG(extack,
> +				       "Point to Multi-Point mode is not enabled");
> +		}
> +
> +		// allow setting node_id concurrently with enabled
> +		if (plca_cfg->node_id >= 0)
> +			curr_plca_cfg->node_id = plca_cfg->node_id;
> +
> +		if (curr_plca_cfg->node_id >= 255) {
> +			NL_SET_ERR_MSG(extack, "PLCA node ID is not set");
> +			ret = -EINVAL;
> +			goto out_drv;
> +		}
> +	}
> +
> +	ret = phydev->drv->set_plca_cfg(phydev, plca_cfg);
> +	if (ret)
> +		goto out_drv;

Unnecessary if() statement.

> +
> +out_drv:
> +	kfree(curr_plca_cfg);
> +	mutex_unlock(&phydev->lock);
> +out:
> +	return ret;
> +}
> +
> +/**
> + * phy_ethtool_get_plca_status - Get PLCA RS status information
> + *
> + * @phydev: the phy_device struct
> + * @plca_st: where to store the retrieved status information
> + */
> +int phy_ethtool_get_plca_status(struct phy_device *phydev,
> +				struct phy_plca_status *plca_st)
> +{
> +	int ret;
> +
> +	if (!phydev->drv) {
> +		ret = -EIO;
> +		goto out;
> +	}
> +
> +	if (!phydev->drv->get_plca_status) {
> +		ret = -EOPNOTSUPP;
> +		goto out;
> +	}
> +
> +	mutex_lock(&phydev->lock);

Same comment here.

> +	ret = phydev->drv->get_plca_status(phydev, plca_st);
> +
> +	if (ret)
> +		goto out_drv;

And here.

> +
> +out_drv:
> +	mutex_unlock(&phydev->lock);
> +out:
> +	return ret;
> +}
> +
>  /**
>   * phy_start_cable_test - Start a cable test
>   *
> diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
> index 8e48b3cec5e7..44bd06be9691 100644
> --- a/drivers/net/phy/phy_device.c
> +++ b/drivers/net/phy/phy_device.c
> @@ -3276,6 +3276,9 @@ static const struct ethtool_phy_ops phy_ethtool_phy_ops = {
>  	.get_sset_count		= phy_ethtool_get_sset_count,
>  	.get_strings		= phy_ethtool_get_strings,
>  	.get_stats		= phy_ethtool_get_stats,
> +	.get_plca_cfg		= phy_ethtool_get_plca_cfg,
> +	.set_plca_cfg		= phy_ethtool_set_plca_cfg,
> +	.get_plca_status	= phy_ethtool_get_plca_status,
>  	.start_cable_test	= phy_start_cable_test,
>  	.start_cable_test_tdr	= phy_start_cable_test_tdr,
>  };
> diff --git a/include/linux/phy.h b/include/linux/phy.h
> index 2a5c2d3a5da5..e0dcd534fe6f 100644
> --- a/include/linux/phy.h
> +++ b/include/linux/phy.h
> @@ -1845,6 +1845,13 @@ int phy_ethtool_get_strings(struct phy_device *phydev, u8 *data);
>  int phy_ethtool_get_sset_count(struct phy_device *phydev);
>  int phy_ethtool_get_stats(struct phy_device *phydev,
>  			  struct ethtool_stats *stats, u64 *data);
> +int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
> +			     struct phy_plca_cfg *plca_cfg);
> +int phy_ethtool_set_plca_cfg(struct phy_device *phydev,
> +			     const struct phy_plca_cfg *plca_cfg,
> +			     struct netlink_ext_ack *extack);
> +int phy_ethtool_get_plca_status(struct phy_device *phydev,
> +				struct phy_plca_status *plca_st);
>  
>  static inline int phy_package_read(struct phy_device *phydev, u32 regnum)
>  {
> -- 
> 2.37.4
> 
> 

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA
  2022-12-11 12:23   ` Russell King (Oracle)
@ 2022-12-11 19:03     ` Piergiorgio Beruto
  2022-12-11 20:34       ` Russell King (Oracle)
  0 siblings, 1 reply; 13+ messages in thread
From: Piergiorgio Beruto @ 2022-12-11 19:03 UTC (permalink / raw)
  To: Russell King (Oracle)
  Cc: Andrew Lunn, Heiner Kallweit, David S. Miller, Eric Dumazet,
	Jakub Kicinski, Paolo Abeni, linux-kernel, netdev,
	Oleksij Rempel

On Sun, Dec 11, 2022 at 12:23:53PM +0000, Russell King (Oracle) wrote:
> On Sat, Dec 10, 2022 at 11:46:39PM +0100, Piergiorgio Beruto wrote:
> > This patch adds the required connection between netlink ethtool and
> > phylib to resolve PLCA get/set config and get status messages.
> > 
> > Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
> > ---
> >  drivers/net/phy/phy.c        | 175 +++++++++++++++++++++++++++++++++++
> >  drivers/net/phy/phy_device.c |   3 +
> >  include/linux/phy.h          |   7 ++
> >  3 files changed, 185 insertions(+)
> > 
> > diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> > index e5b6cb1a77f9..40d90ed2f0fb 100644
> > --- a/drivers/net/phy/phy.c
> > +++ b/drivers/net/phy/phy.c
> > @@ -543,6 +543,181 @@ int phy_ethtool_get_stats(struct phy_device *phydev,
> >  }
> >  EXPORT_SYMBOL(phy_ethtool_get_stats);
> >  
> > +/**
> > + * phy_ethtool_get_plca_cfg - Get PLCA RS configuration
> > + *
> 
> You shouldn't have an empty line in the comment here
I was trying to follow the style of this file. All other functions start
like this, including an empty line. Do you want me to:
a) follow your indication and leave all other functions as they are?
b) Change all functions docs to follow your suggestion?
c) leave it as-is?

Please, advise.

> 
> > + * @phydev: the phy_device struct
> > + * @plca_cfg: where to store the retrieved configuration
> 
> Maybe have an empty line, followed by a bit of text describing what this
> function does and the return codes it generates?
Again, I was trying to follow the style of the docs in this file.
Do you still want me to add a description here?

> 
> > + */
> > +int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
> > +			     struct phy_plca_cfg *plca_cfg)
> > +{
> > +	int ret;
> > +
> > +	if (!phydev->drv) {
> > +		ret = -EIO;
> > +		goto out;
> > +	}
> > +
> > +	if (!phydev->drv->get_plca_cfg) {
> > +		ret = -EOPNOTSUPP;
> > +		goto out;
> > +	}
> > +
> > +	memset(plca_cfg, 0xFF, sizeof(*plca_cfg));
> > +
> > +	mutex_lock(&phydev->lock);
> 
> Maybe move the memset() and mutex_lock() before the first if() statement
> above? 
Once more, all other functions in this file take the mutex -after-
checking for phydev->drv and checking the specific function. Therefore,
I assumed that was a safe thing to do. If not, should we fix all of
these functions in this file?

> Maybe the memset() should be done by plca_get_cfg_prepare_data()?
I put the memset there when the function was exported. Since we're not
exporting it anymore, we can put it in the _prepare() function in plca.c
as you suggest. I just wonder if there is a real advantage in doing
this?

> Wouldn't all implementations need to memset this to 0xff?
It actually depends on what these implementations are trying to achieve.
I would say, likely yes, but not necessairly.

> 
> Also, lower-case 0xff please.
Done.

> 
> > +	ret = phydev->drv->get_plca_cfg(phydev, plca_cfg);
> > +
> > +	if (ret)
> > +		goto out_drv;
> > +
> > +out_drv:
> 
> This if() and out_drv label seems unused (although with the above
> suggested change, you will need to move the "out" label here.)
Noted, thanks.
> 
> > +	mutex_unlock(&phydev->lock);
> > +out:
> > +	return ret;
> > +}
> > +
> > +/**
> > + * phy_ethtool_set_plca_cfg - Set PLCA RS configuration
> > + *
> > + * @phydev: the phy_device struct
> > + * @extack: extack for reporting useful error messages
> > + * @plca_cfg: new PLCA configuration to apply
> > + */
> > +int phy_ethtool_set_plca_cfg(struct phy_device *phydev,
> > +			     const struct phy_plca_cfg *plca_cfg,
> > +			     struct netlink_ext_ack *extack)
> > +{
> > +	int ret;
> > +	struct phy_plca_cfg *curr_plca_cfg = 0;
> 
> Unnecessary initialiser. Also, reverse Christmas-tree please.
Oops, that was not intentional. Fixed.

> > +
> > +	if (!phydev->drv) {
> > +		ret = -EIO;
> > +		goto out;
> > +	}
> > +
> > +	if (!phydev->drv->set_plca_cfg ||
> > +	    !phydev->drv->get_plca_cfg) {
> > +		ret = -EOPNOTSUPP;
> > +		goto out;
> > +	}
> > +
> > +	curr_plca_cfg = kmalloc(sizeof(*curr_plca_cfg), GFP_KERNEL);
> 
> What if kmalloc() returns NULL?
Fixed, returning -ENOMEM now.

> 
> > +	memset(curr_plca_cfg, 0xFF, sizeof(*curr_plca_cfg));
> > +
> > +	mutex_lock(&phydev->lock);
> 
> Consider moving the above three to the beginning of the function so
> phydev->drv is checked under the mutex.
Same discussion as before. No other functions in this file do this. Let
me know how would you like to see this fixed.

> > +
> > +	ret = phydev->drv->set_plca_cfg(phydev, plca_cfg);
> > +	if (ret)
> > +		goto out_drv;
> 
> Unnecessary if() statement.
Yup, fixed.

> > +	ret = phydev->drv->get_plca_status(phydev, plca_st);
> > +
> > +	if (ret)
> > +		goto out_drv;
> 
> And here.
Fixed.


Please, let me know how to proceed.
Thanks again for your kind review.

Piergiorgio

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA
  2022-12-11 19:03     ` Piergiorgio Beruto
@ 2022-12-11 20:34       ` Russell King (Oracle)
  2022-12-12  9:51         ` Piergiorgio Beruto
  2022-12-12 15:22         ` Andrew Lunn
  0 siblings, 2 replies; 13+ messages in thread
From: Russell King (Oracle) @ 2022-12-11 20:34 UTC (permalink / raw)
  To: Piergiorgio Beruto
  Cc: Andrew Lunn, Heiner Kallweit, David S. Miller, Eric Dumazet,
	Jakub Kicinski, Paolo Abeni, linux-kernel, netdev,
	Oleksij Rempel

On Sun, Dec 11, 2022 at 08:03:15PM +0100, Piergiorgio Beruto wrote:
> On Sun, Dec 11, 2022 at 12:23:53PM +0000, Russell King (Oracle) wrote:
> > On Sat, Dec 10, 2022 at 11:46:39PM +0100, Piergiorgio Beruto wrote:
> > > This patch adds the required connection between netlink ethtool and
> > > phylib to resolve PLCA get/set config and get status messages.
> > > 
> > > Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
> > > ---
> > >  drivers/net/phy/phy.c        | 175 +++++++++++++++++++++++++++++++++++
> > >  drivers/net/phy/phy_device.c |   3 +
> > >  include/linux/phy.h          |   7 ++
> > >  3 files changed, 185 insertions(+)
> > > 
> > > diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> > > index e5b6cb1a77f9..40d90ed2f0fb 100644
> > > --- a/drivers/net/phy/phy.c
> > > +++ b/drivers/net/phy/phy.c
> > > @@ -543,6 +543,181 @@ int phy_ethtool_get_stats(struct phy_device *phydev,
> > >  }
> > >  EXPORT_SYMBOL(phy_ethtool_get_stats);
> > >  
> > > +/**
> > > + * phy_ethtool_get_plca_cfg - Get PLCA RS configuration
> > > + *
> > 
> > You shouldn't have an empty line in the comment here
> I was trying to follow the style of this file. All other functions start
> like this, including an empty line. Do you want me to:
> a) follow your indication and leave all other functions as they are?
> b) Change all functions docs to follow your suggestion?
> c) leave it as-is?
> 
> Please, advise.

Please see Documentation/doc-guide/kernel-doc.rst

"Function parameters
~~~~~~~~~~~~~~~~~~~

Each function argument should be described in order, immediately following
the short function description.  Do not leave a blank line between the
function description and the arguments, nor between the arguments."

Note the last sentence - there should _not_ be a blank line, so please
follow this for new submissions. I don't think we care enough to fix
what's already there though.

> 
> > 
> > > + * @phydev: the phy_device struct
> > > + * @plca_cfg: where to store the retrieved configuration
> > 
> > Maybe have an empty line, followed by a bit of text describing what this
> > function does and the return codes it generates?
> Again, I was trying to follow the style of the docs in this file.
> Do you still want me to add a description here?

Convention is a blank line - as illustrated by the general format
in the documentation file I refer to above.

> 
> > 
> > > + */
> > > +int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
> > > +			     struct phy_plca_cfg *plca_cfg)
> > > +{
> > > +	int ret;
> > > +
> > > +	if (!phydev->drv) {
> > > +		ret = -EIO;
> > > +		goto out;
> > > +	}
> > > +
> > > +	if (!phydev->drv->get_plca_cfg) {
> > > +		ret = -EOPNOTSUPP;
> > > +		goto out;
> > > +	}
> > > +
> > > +	memset(plca_cfg, 0xFF, sizeof(*plca_cfg));
> > > +
> > > +	mutex_lock(&phydev->lock);
> > 
> > Maybe move the memset() and mutex_lock() before the first if() statement
> > above? 
> Once more, all other functions in this file take the mutex -after-
> checking for phydev->drv and checking the specific function. Therefore,
> I assumed that was a safe thing to do. If not, should we fix all of
> these functions in this file?

This is a review comment I've made already, but you seem to have ignored
it. Please ensure that new contributions are safe. Yes, existing code
may not be, and that's something we should fix, but your contribution
should at least be safer than the existing code.

> > Maybe the memset() should be done by plca_get_cfg_prepare_data()?
> I put the memset there when the function was exported. Since we're not
> exporting it anymore, we can put it in the _prepare() function in plca.c
> as you suggest. I just wonder if there is a real advantage in doing
> this?

... because of what I said in the following line below.

> 
> > Wouldn't all implementations need to memset this to 0xff?
> It actually depends on what these implementations are trying to achieve.
> I would say, likely yes, but not necessairly.

Why wouldn't they want this initialisation, given that the use of
negative values means "not implemented" - surely we want common code
to indicate everything is not implemented until something writes to
the parameter?

What if an implementation decides to manually initialise each member
to -1 and then someone adds an additional field later (e.g. for that
0x0A) ?

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA
  2022-12-11 20:34       ` Russell King (Oracle)
@ 2022-12-12  9:51         ` Piergiorgio Beruto
  2022-12-13 11:34           ` Russell King (Oracle)
  2022-12-12 15:22         ` Andrew Lunn
  1 sibling, 1 reply; 13+ messages in thread
From: Piergiorgio Beruto @ 2022-12-12  9:51 UTC (permalink / raw)
  To: Russell King (Oracle)
  Cc: Andrew Lunn, Heiner Kallweit, David S. Miller, Eric Dumazet,
	Jakub Kicinski, Paolo Abeni, linux-kernel, netdev,
	Oleksij Rempel

On Sun, Dec 11, 2022 at 08:34:14PM +0000, Russell King (Oracle) wrote:
> On Sun, Dec 11, 2022 at 08:03:15PM +0100, Piergiorgio Beruto wrote:
> > On Sun, Dec 11, 2022 at 12:23:53PM +0000, Russell King (Oracle) wrote:
> > > On Sat, Dec 10, 2022 at 11:46:39PM +0100, Piergiorgio Beruto wrote:
> > > > This patch adds the required connection between netlink ethtool and
> > > > phylib to resolve PLCA get/set config and get status messages.
> > > > 
> > > > Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
> > > > ---
> > > >  drivers/net/phy/phy.c        | 175 +++++++++++++++++++++++++++++++++++
> > > >  drivers/net/phy/phy_device.c |   3 +
> > > >  include/linux/phy.h          |   7 ++
> > > >  3 files changed, 185 insertions(+)
> > > > 
> > > > diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> > > > index e5b6cb1a77f9..40d90ed2f0fb 100644
> > > > --- a/drivers/net/phy/phy.c
> > > > +++ b/drivers/net/phy/phy.c
> > > > @@ -543,6 +543,181 @@ int phy_ethtool_get_stats(struct phy_device *phydev,
> > > >  }
> > > >  EXPORT_SYMBOL(phy_ethtool_get_stats);
> > > >  
> > > > +/**
> > > > + * phy_ethtool_get_plca_cfg - Get PLCA RS configuration
> > > > + *
> > > 
> > > You shouldn't have an empty line in the comment here
> > I was trying to follow the style of this file. All other functions start
> > like this, including an empty line. Do you want me to:
> > a) follow your indication and leave all other functions as they are?
> > b) Change all functions docs to follow your suggestion?
> > c) leave it as-is?
> > 
> > Please, advise.
> 
> Please see Documentation/doc-guide/kernel-doc.rst
> 
> "Function parameters
> ~~~~~~~~~~~~~~~~~~~
> 
> Each function argument should be described in order, immediately following
> the short function description.  Do not leave a blank line between the
> function description and the arguments, nor between the arguments."
> 
> Note the last sentence - there should _not_ be a blank line, so please
> follow this for new submissions. I don't think we care enough to fix
> what's already there though.
Fair enough, I'll change this. However, I would suggest to write these
kind of rules (about following the new style vs keeping consistency with
what it's there already) to help newcomers like me understanding what
the policy actually is. I got different opinions about that.

> 
> > 
> > > 
> > > > + * @phydev: the phy_device struct
> > > > + * @plca_cfg: where to store the retrieved configuration
> > > 
> > > Maybe have an empty line, followed by a bit of text describing what this
> > > function does and the return codes it generates?
> > Again, I was trying to follow the style of the docs in this file.
> > Do you still want me to add a description here?
> 
> Convention is a blank line - as illustrated by the general format
> in the documentation file I refer to above.
Okay.

> > 
> > > 
> > > > + */
> > > > +int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
> > > > +			     struct phy_plca_cfg *plca_cfg)
> > > > +{
> > > > +	int ret;
> > > > +
> > > > +	if (!phydev->drv) {
> > > > +		ret = -EIO;
> > > > +		goto out;
> > > > +	}
> > > > +
> > > > +	if (!phydev->drv->get_plca_cfg) {
> > > > +		ret = -EOPNOTSUPP;
> > > > +		goto out;
> > > > +	}
> > > > +
> > > > +	memset(plca_cfg, 0xFF, sizeof(*plca_cfg));
> > > > +
> > > > +	mutex_lock(&phydev->lock);
> > > 
> > > Maybe move the memset() and mutex_lock() before the first if() statement
> > > above? 
> > Once more, all other functions in this file take the mutex -after-
> > checking for phydev->drv and checking the specific function. Therefore,
> > I assumed that was a safe thing to do. If not, should we fix all of
> > these functions in this file?
> 
> This is a review comment I've made already, but you seem to have ignored
> it. Please ensure that new contributions are safe. Yes, existing code
> may not be, and that's something we should fix, but your contribution
> should at least be safer than the existing code.
> 
Russle, I did not actually ignore your comment. Looking back at the
history, you were commenting on the functions in plca.c and we were
talking about the global rtnl lock.

So here what it looks to me:
1. in a previous version of the patchset, the phy_ethtool_*_plca_*
functions were exported, therefore the phydev lock had to be acquired as
you cannot say from which context exactly these could be called.

2. After your comments about NOT exporting these functions, I believe we
can safely assume these are called only from plca.c (ethtool interface).

3. As you can see all of these functions are called with the rtnl lock
being held from ethtool.

Therefore... do we really need to take the phydev mutex at all?
Do we really need to perform (again) checks against phydev being not
NULL and such?

I would suggest to just remove all of these checks and the phydev mutex
locking, unless you see any reason for whcih we should take it.

Thoughts?


> > > Wouldn't all implementations need to memset this to 0xff?
> > It actually depends on what these implementations are trying to achieve.
> > I would say, likely yes, but not necessairly.
> 
> Why wouldn't they want this initialisation, given that the use of
> negative values means "not implemented" - surely we want common code
> to indicate everything is not implemented until something writes to
> the parameter?
> 
> What if an implementation decides to manually initialise each member
> to -1 and then someone adds an additional field later (e.g. for that
> 0x0A) ?
Fair enough, as I said, this makes sesne to me, I just wanted to be sure
we agree on the purpose.

I moved the memset to the upper layers.

Thanks!
Piergiorgio

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA
  2022-12-11 20:34       ` Russell King (Oracle)
  2022-12-12  9:51         ` Piergiorgio Beruto
@ 2022-12-12 15:22         ` Andrew Lunn
  1 sibling, 0 replies; 13+ messages in thread
From: Andrew Lunn @ 2022-12-12 15:22 UTC (permalink / raw)
  To: Russell King (Oracle)
  Cc: Piergiorgio Beruto, Heiner Kallweit, David S. Miller,
	Eric Dumazet, Jakub Kicinski, Paolo Abeni, linux-kernel, netdev,
	Oleksij Rempel

On Sun, Dec 11, 2022 at 08:34:14PM +0000, Russell King (Oracle) wrote:
> On Sun, Dec 11, 2022 at 08:03:15PM +0100, Piergiorgio Beruto wrote:
> > On Sun, Dec 11, 2022 at 12:23:53PM +0000, Russell King (Oracle) wrote:
> > > On Sat, Dec 10, 2022 at 11:46:39PM +0100, Piergiorgio Beruto wrote:
> > > > This patch adds the required connection between netlink ethtool and
> > > > phylib to resolve PLCA get/set config and get status messages.
> > > > 
> > > > Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
> > > > ---
> > > >  drivers/net/phy/phy.c        | 175 +++++++++++++++++++++++++++++++++++
> > > >  drivers/net/phy/phy_device.c |   3 +
> > > >  include/linux/phy.h          |   7 ++
> > > >  3 files changed, 185 insertions(+)
> > > > 
> > > > diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> > > > index e5b6cb1a77f9..40d90ed2f0fb 100644
> > > > --- a/drivers/net/phy/phy.c
> > > > +++ b/drivers/net/phy/phy.c
> > > > @@ -543,6 +543,181 @@ int phy_ethtool_get_stats(struct phy_device *phydev,
> > > >  }
> > > >  EXPORT_SYMBOL(phy_ethtool_get_stats);
> > > >  
> > > > +/**
> > > > + * phy_ethtool_get_plca_cfg - Get PLCA RS configuration
> > > > + *
> > > 
> > > You shouldn't have an empty line in the comment here
> > I was trying to follow the style of this file. All other functions start
> > like this, including an empty line. Do you want me to:
> > a) follow your indication and leave all other functions as they are?
> > b) Change all functions docs to follow your suggestion?
> > c) leave it as-is?
> > 
> > Please, advise.
> 
> Please see Documentation/doc-guide/kernel-doc.rst
> 
> "Function parameters
> ~~~~~~~~~~~~~~~~~~~
> 
> Each function argument should be described in order, immediately following
> the short function description.  Do not leave a blank line between the
> function description and the arguments, nor between the arguments."
> 
> Note the last sentence - there should _not_ be a blank line, so please
> follow this for new submissions. I don't think we care enough to fix
> what's already there though.
> 
> > 
> > > 
> > > > + * @phydev: the phy_device struct
> > > > + * @plca_cfg: where to store the retrieved configuration
> > > 
> > > Maybe have an empty line, followed by a bit of text describing what this
> > > function does and the return codes it generates?
> > Again, I was trying to follow the style of the docs in this file.
> > Do you still want me to add a description here?
> 
> Convention is a blank line - as illustrated by the general format
> in the documentation file I refer to above.
> 
> > 
> > > 
> > > > + */
> > > > +int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
> > > > +			     struct phy_plca_cfg *plca_cfg)
> > > > +{
> > > > +	int ret;
> > > > +
> > > > +	if (!phydev->drv) {
> > > > +		ret = -EIO;
> > > > +		goto out;
> > > > +	}
> > > > +
> > > > +	if (!phydev->drv->get_plca_cfg) {
> > > > +		ret = -EOPNOTSUPP;
> > Once more, all other functions in this file take the mutex -after-
> > checking for phydev->drv and checking the specific function. Therefore,
> > I assumed that was a safe thing to do. If not, should we fix all of
> > these functions in this file?
> 
> This is a review comment I've made already, but you seem to have ignored
> it. Please ensure that new contributions are safe. Yes, existing code
> may not be, and that's something we should fix, but your contribution
> should at least be safer than the existing code.

I have a patch ready for fixing the cable test examples of performing
the test before taking the lock. I was going to post it to net-next in
a couple of weeks time. Or do you think it should be to net?

	Andrew

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA
  2022-12-12  9:51         ` Piergiorgio Beruto
@ 2022-12-13 11:34           ` Russell King (Oracle)
  0 siblings, 0 replies; 13+ messages in thread
From: Russell King (Oracle) @ 2022-12-13 11:34 UTC (permalink / raw)
  To: Piergiorgio Beruto
  Cc: Andrew Lunn, Heiner Kallweit, David S. Miller, Eric Dumazet,
	Jakub Kicinski, Paolo Abeni, linux-kernel, netdev,
	Oleksij Rempel

On Mon, Dec 12, 2022 at 10:51:18AM +0100, Piergiorgio Beruto wrote:
> On Sun, Dec 11, 2022 at 08:34:14PM +0000, Russell King (Oracle) wrote:
> > Please see Documentation/doc-guide/kernel-doc.rst
> > 
> > "Function parameters
> > ~~~~~~~~~~~~~~~~~~~
> > 
> > Each function argument should be described in order, immediately following
> > the short function description.  Do not leave a blank line between the
> > function description and the arguments, nor between the arguments."
> > 
> > Note the last sentence - there should _not_ be a blank line, so please
> > follow this for new submissions. I don't think we care enough to fix
> > what's already there though.
> Fair enough, I'll change this. However, I would suggest to write these
> kind of rules (about following the new style vs keeping consistency with
> what it's there already) to help newcomers like me understanding what
> the policy actually is. I got different opinions about that.

phy.c has two different formats for docbook comments - some of them
are to the documented format, others with the extra blank line. Given
that correct form is without the blank line, new docbook comments
should conform to the standard format.

> > This is a review comment I've made already, but you seem to have ignored
> > it. Please ensure that new contributions are safe. Yes, existing code
> > may not be, and that's something we should fix, but your contribution
> > should at least be safer than the existing code.
> > 
> Russle, I did not actually ignore your comment. Looking back at the
> history, you were commenting on the functions in plca.c and we were
> talking about the global rtnl lock.

Thanks for checking back, you're correct. You can ignore this comment
as it won't make any difference.

Looking at phy_remove(), it wouldn't make any difference anyway, so
please keep the code as-is.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

^ permalink raw reply	[flat|nested] 13+ messages in thread
end of thread, other threads:[~2022-12-13 11:35 UTC | newest]

Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-12-10 22:45 [PATCH v6 net-next 0/5] add PLCA RS support and onsemi NCN26000 Piergiorgio Beruto
2022-12-10 22:46 ` [PATCH v6 net-next 1/5] net/ethtool: add netlink interface for the PLCA RS Piergiorgio Beruto
2022-12-10 22:46 ` [PATCH v6 net-next 2/5] drivers/net/phy: add the link modes for the 10BASE-T1S Ethernet PHY Piergiorgio Beruto
2022-12-10 22:46 ` [PATCH v6 net-next 3/5] drivers/net/phy: add connection between ethtool and phylib for PLCA Piergiorgio Beruto
2022-12-11 12:05   ` kernel test robot
2022-12-11 12:23   ` Russell King (Oracle)
2022-12-11 19:03     ` Piergiorgio Beruto
2022-12-11 20:34       ` Russell King (Oracle)
2022-12-12  9:51         ` Piergiorgio Beruto
2022-12-13 11:34           ` Russell King (Oracle)
2022-12-12 15:22         ` Andrew Lunn
2022-12-10 22:46 ` [PATCH v6 net-next 4/5] drivers/net/phy: add helpers to get/set PLCA configuration Piergiorgio Beruto
2022-12-10 22:47 ` [PATCH v6 net-next 5/5] drivers/net/phy: add driver for the onsemi NCN26000 10BASE-T1S PHY Piergiorgio Beruto

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.