* "htt version request timed out" with the last 4.1.1.c1 firmware [not found] ` <2025478478.2725588.1512857709726@mail.yahoo.com> @ 2017-12-09 22:23 ` Paul Nuville 2017-12-14 13:14 ` Kalle Valo 0 siblings, 1 reply; 8+ messages in thread From: Paul Nuville @ 2017-12-09 22:23 UTC (permalink / raw) To: ath10k Hello all, I've installed Archlinux on a Samsung Galaxy Book 10.6", and I'm trying to set up the wifi. The only firmware that seems to be suitable is the lastest 4.1.1.c1 one. But I've some errors and neither ip ad networkmanager are able to set up the wlan interface. Here are some outputs : # lspci -k 01:00.0 Network controller: Qualcomm Atheros QCA6174 802.11ac Wireless Network Adapter (rev 32) Subsystem: Samsung Electronics Co Ltd QCA6174 802.11ac Wireless Network Adapter Kernel modules: ath10k_pci # lsmod | grep ath10k ath10k_pci 53248 0 ath10k_core 356352 1 ath10k_pci ath 32768 1 ath10k_core mac80211 827392 1 ath10k_core cfg80211 647168 3 mac80211,ath,ath10k_core # dmesg | grep ath10k [ 1777.602748] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 1777.861498] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre- cal-pci-0000:01:00.0.bin failed with error -2 [ 1777.861509] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal- pci-0000:01:00.0.bin failed with error -2 [ 1777.861572] ath10k_pci 0000:01:00.0: invalid firmware magic [ 1777.861587] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/ QCA6174/hw3.0/firmware-5.bin failed with error -2 [ 1777.861815] ath10k_pci 0000:01:00.0: qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 144d:c150 [ 1777.861817] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0 [ 1777.862589] ath10k_pci 0000:01:00.0: firmware ver WLAN.RM.2.0-00180- QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5 [ 1777.926402] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=003e,subsystem-vendor=144d,subsystem-device=c150 from ath10k/QCA6174/hw3.0/board-2.bin [ 1777.926428] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 ed5f849a [ 1781.596516] ath10k_pci 0000:01:00.0: htt version request timed out [ 1781.596523] ath10k_pci 0000:01:00.0: failed to setup htt: -110 [ 1781.669496] ath10k_pci 0000:01:00.0: could not init core (-110) [ 1781.669544] ath10k_pci 0000:01:00.0: could not probe fw (-110) Any help will be apreciate ! Thank you in advance, Paul _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: "htt version request timed out" with the last 4.1.1.c1 firmware 2017-12-09 22:23 ` "htt version request timed out" with the last 4.1.1.c1 firmware Paul Nuville @ 2017-12-14 13:14 ` Kalle Valo 2017-12-14 18:33 ` Adrian Chadd 2017-12-14 21:21 ` "htt version request timed out" with the last 4.1.1.c1 firmware Ryan Hsu 0 siblings, 2 replies; 8+ messages in thread From: Kalle Valo @ 2017-12-14 13:14 UTC (permalink / raw) To: Paul Nuville; +Cc: ath10k Paul Nuville <paulnuville@yahoo.fr> writes: > I've installed Archlinux on a Samsung Galaxy Book 10.6", and I'm trying to set > up the wifi. The only firmware that seems to be suitable is the lastest 4.1.1.c1 > one. But I've some errors and neither ip ad networkmanager are able to set up > the wlan interface. > Here are some outputs : > [...] > [ 1777.861815] ath10k_pci 0000:01:00.0: qca6174 hw3.2 target 0x05030000 > chip_id 0x00340aff sub 144d:c150 > [ 1777.861817] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs > 0 testmode 0 > [ 1777.862589] ath10k_pci 0000:01:00.0: firmware ver WLAN.RM.2.0-00180- > QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5 > [ 1777.926402] ath10k_pci 0000:01:00.0: failed to fetch board data for > bus=pci,vendor=168c,device=003e,subsystem-vendor=144d,subsystem-device=c150 > from ath10k/QCA6174/hw3.0/board-2.bin > [ 1777.926428] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 > ed5f849a > [ 1781.596516] ath10k_pci 0000:01:00.0: htt version request timed out ath10k didn't file the correct board file from board-2.bin. Try updating to the latest board-2.bin: https://github.com/kvalo/ath10k-firmware/blob/master/QCA6174/hw3.0/board-2.bin The md5sum should be: eddaa17fa2092bcd6713720116e421f1 -- Kalle Valo _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: "htt version request timed out" with the last 4.1.1.c1 firmware 2017-12-14 13:14 ` Kalle Valo @ 2017-12-14 18:33 ` Adrian Chadd 2017-12-14 21:22 ` Ryan Hsu 2017-12-14 21:21 ` "htt version request timed out" with the last 4.1.1.c1 firmware Ryan Hsu 1 sibling, 1 reply; 8+ messages in thread From: Adrian Chadd @ 2017-12-14 18:33 UTC (permalink / raw) To: Kalle Valo; +Cc: ath10k, Paul Nuville Hi, I've had this issue with a 4.11 update from QSDK (4.0.8.) ILQ-1.1.8 worked fine with ye olde backports. Is it really just a board-2.bin issue? I tried it and it didn't fix it. -adrian _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: "htt version request timed out" with the last 4.1.1.c1 firmware 2017-12-14 18:33 ` Adrian Chadd @ 2017-12-14 21:22 ` Ryan Hsu 2017-12-14 21:55 ` Adrian Chadd 0 siblings, 1 reply; 8+ messages in thread From: Ryan Hsu @ 2017-12-14 21:22 UTC (permalink / raw) To: Adrian Chadd, Kalle Valo; +Cc: ath10k, Paul Nuville On 12/14/2017 10:33 AM, Adrian Chadd wrote: > Hi, > > I've had this issue with a 4.11 update from QSDK (4.0.8.) ILQ-1.1.8 > worked fine with ye olde backports. > > Is it really just a board-2.bin issue? I tried it and it didn't fix it. The case Paul has seems due to the correct board file missing. Not sure what issue you're seeing? any logs? Also the issue is for QCA6174, does your QSDK 4.0.8 run with QCA6174? -- Ryan Hsu _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: "htt version request timed out" with the last 4.1.1.c1 firmware 2017-12-14 21:22 ` Ryan Hsu @ 2017-12-14 21:55 ` Adrian Chadd 2017-12-19 1:17 ` Adrian Chadd 0 siblings, 1 reply; 8+ messages in thread From: Adrian Chadd @ 2017-12-14 21:55 UTC (permalink / raw) To: Ryan Hsu; +Cc: Kalle Valo, ath10k, Paul Nuville Hi, * QSDK 4.0.8 doesn't run with QCA6174 - HTT timeout as above * QSDK ILQ 1.1.8 runs with QCA6174 * The HTT debugging shows that after the HTC/HTT stuff is setup, none of the HTT "i'm awake" messages are coming back. I'll try the latest firmware and board data from Kalle's repository and see if that makes a difference. Right now I'm about 2/3rds the way through undoing the 1.1.8 -> 4.0.8 changes in ath10k to see if I can narrow down the actual regression. -adrian _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: "htt version request timed out" with the last 4.1.1.c1 firmware 2017-12-14 21:55 ` Adrian Chadd @ 2017-12-19 1:17 ` Adrian Chadd 2017-12-20 18:37 ` lastest firmware 9984 (10.3-3.4.104) Sebastian Gottschall 0 siblings, 1 reply; 8+ messages in thread From: Adrian Chadd @ 2017-12-19 1:17 UTC (permalink / raw) To: Ryan Hsu; +Cc: Kalle Valo, ath10k, Paul Nuville hi, fyi - i tried the latest board-2.bin and firmware-6.bin from kvalo's ath10k repository - still getting HTT timeouts. This is on the QSDK 4.0.8 backports. -adrian On 14 December 2017 at 13:55, Adrian Chadd <adrian@freebsd.org> wrote: > Hi, > > * QSDK 4.0.8 doesn't run with QCA6174 - HTT timeout as above > * QSDK ILQ 1.1.8 runs with QCA6174 > * The HTT debugging shows that after the HTC/HTT stuff is setup, none > of the HTT "i'm awake" messages are coming back. > > I'll try the latest firmware and board data from Kalle's repository > and see if that makes a difference. Right now I'm about 2/3rds the way > through undoing the 1.1.8 -> 4.0.8 changes in ath10k to see if I can > narrow down the actual regression. > > > > > -adrian _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 8+ messages in thread
* lastest firmware 9984 (10.3-3.4.104) 2017-12-19 1:17 ` Adrian Chadd @ 2017-12-20 18:37 ` Sebastian Gottschall 0 siblings, 0 replies; 8+ messages in thread From: Sebastian Gottschall @ 2017-12-20 18:37 UTC (permalink / raw) To: ath10k with the most recent 10.3-3.4.104 firmware for 9984 i see this ath10k message [ 2884.160502] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode [ 2884.160545] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode [ 2884.167760] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode [ 2884.175905] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode in addition there is a problem since a long time in wds ap mode. all wpa sta stations (no matter which chipset, ath9k and ath10k tests) gets kicked out at wpa rekeying. (and reconnect immediatly) this problem exists on 99x0 and 9984 but not on 988x any ideas? Sebastian _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: "htt version request timed out" with the last 4.1.1.c1 firmware 2017-12-14 13:14 ` Kalle Valo 2017-12-14 18:33 ` Adrian Chadd @ 2017-12-14 21:21 ` Ryan Hsu 1 sibling, 0 replies; 8+ messages in thread From: Ryan Hsu @ 2017-12-14 21:21 UTC (permalink / raw) To: Kalle Valo, Paul Nuville; +Cc: ath10k On 12/14/2017 05:14 AM, Kalle Valo wrote: > Paul Nuville <paulnuville@yahoo.fr> writes: > >> I've installed Archlinux on a Samsung Galaxy Book 10.6", and I'm trying to set >> up the wifi. The only firmware that seems to be suitable is the lastest 4.1.1.c1 >> one. But I've some errors and neither ip ad networkmanager are able to set up >> the wlan interface. >> Here are some outputs : >> > [...] > >> [ 1777.861815] ath10k_pci 0000:01:00.0: qca6174 hw3.2 target 0x05030000 >> chip_id 0x00340aff sub 144d:c150 >> [ 1777.861817] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs >> 0 testmode 0 >> [ 1777.862589] ath10k_pci 0000:01:00.0: firmware ver WLAN.RM.2.0-00180- >> QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5 >> [ 1777.926402] ath10k_pci 0000:01:00.0: failed to fetch board data for >> bus=pci,vendor=168c,device=003e,subsystem-vendor=144d,subsystem-device=c150 >> from ath10k/QCA6174/hw3.0/board-2.bin >> [ 1777.926428] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 >> ed5f849a >> [ 1781.596516] ath10k_pci 0000:01:00.0: htt version request timed out > ath10k didn't file the correct board file from board-2.bin. Try updating > to the latest board-2.bin: > > https://github.com/kvalo/ath10k-firmware/blob/master/QCA6174/hw3.0/board-2.bin > > The md5sum should be: > > eddaa17fa2092bcd6713720116e421f1 Other than updating the board-2.bin file, you might also want to make sure you update the firmware file. I saw you're still using the Rm2.0 instead of the 4.4.1.c1 you asked. -- Ryan Hsu _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2017-12-20 18:55 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <2025478478.2725588.1512857709726.ref@mail.yahoo.com>
[not found] ` <2025478478.2725588.1512857709726@mail.yahoo.com>
2017-12-09 22:23 ` "htt version request timed out" with the last 4.1.1.c1 firmware Paul Nuville
2017-12-14 13:14 ` Kalle Valo
2017-12-14 18:33 ` Adrian Chadd
2017-12-14 21:22 ` Ryan Hsu
2017-12-14 21:55 ` Adrian Chadd
2017-12-19 1:17 ` Adrian Chadd
2017-12-20 18:37 ` lastest firmware 9984 (10.3-3.4.104) Sebastian Gottschall
2017-12-14 21:21 ` "htt version request timed out" with the last 4.1.1.c1 firmware Ryan Hsu
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.