* [PATCH net-next 01/12] net: phy: ste10Xp: Remove wrong SUPPORTED_Pause
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:53 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 02/12] net: phy: et1011c: Remove incorrect missing 1000 Half Andrew Lunn
` (11 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
The PHY driver should not indicate that Pause is supported. It is upto
the MAC drive enable it, if it supports Pause frames. So remove it
from the ste10Xp driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/ste10Xp.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/phy/ste10Xp.c b/drivers/net/phy/ste10Xp.c
index fbd548a1ad84..2fe9a87b55b5 100644
--- a/drivers/net/phy/ste10Xp.c
+++ b/drivers/net/phy/ste10Xp.c
@@ -86,7 +86,7 @@ static struct phy_driver ste10xp_pdriver[] = {
.phy_id = STE101P_PHY_ID,
.phy_id_mask = 0xfffffff0,
.name = "STe101p",
- .features = PHY_BASIC_FEATURES | SUPPORTED_Pause,
+ .features = PHY_BASIC_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.config_init = ste10Xp_config_init,
.ack_interrupt = ste10Xp_ack_interrupt,
@@ -97,7 +97,7 @@ static struct phy_driver ste10xp_pdriver[] = {
.phy_id = STE100P_PHY_ID,
.phy_id_mask = 0xffffffff,
.name = "STe100p",
- .features = PHY_BASIC_FEATURES | SUPPORTED_Pause,
+ .features = PHY_BASIC_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.config_init = ste10Xp_config_init,
.ack_interrupt = ste10Xp_ack_interrupt,
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [PATCH net-next 01/12] net: phy: ste10Xp: Remove wrong SUPPORTED_Pause
2018-09-02 17:06 ` [PATCH net-next 01/12] net: phy: ste10Xp: Remove wrong SUPPORTED_Pause Andrew Lunn
@ 2018-09-03 17:53 ` Florian Fainelli
2018-09-04 1:20 ` Andrew Lunn
0 siblings, 1 reply; 30+ messages in thread
From: Florian Fainelli @ 2018-09-03 17:53 UTC (permalink / raw)
To: Andrew Lunn, David Miller; +Cc: netdev, maxime.chevallier
On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> The PHY driver should not indicate that Pause is supported. It is upto
> the MAC drive enable it, if it supports Pause frames. So remove it
> from the ste10Xp driver.
This came up before when Timur was cleaning up the Pause|ASym_Pause
advertisment bits, and we agreed that a driver that cannot have the
Asym_Pause bit writable, e.g: bcm63xx, would have to specifically leave
SUPPORTED_Pause as a way to tell PHYLIB about that situation. See:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/net/phy?id=529ed12752635ba8a35dc78ec70ed6f42570b4ca
Can you check the datasheet if available?
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> ---
> drivers/net/phy/ste10Xp.c | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/phy/ste10Xp.c b/drivers/net/phy/ste10Xp.c
> index fbd548a1ad84..2fe9a87b55b5 100644
> --- a/drivers/net/phy/ste10Xp.c
> +++ b/drivers/net/phy/ste10Xp.c
> @@ -86,7 +86,7 @@ static struct phy_driver ste10xp_pdriver[] = {
> .phy_id = STE101P_PHY_ID,
> .phy_id_mask = 0xfffffff0,
> .name = "STe101p",
> - .features = PHY_BASIC_FEATURES | SUPPORTED_Pause,
> + .features = PHY_BASIC_FEATURES,
> .flags = PHY_HAS_INTERRUPT,
> .config_init = ste10Xp_config_init,
> .ack_interrupt = ste10Xp_ack_interrupt,
> @@ -97,7 +97,7 @@ static struct phy_driver ste10xp_pdriver[] = {
> .phy_id = STE100P_PHY_ID,
> .phy_id_mask = 0xffffffff,
> .name = "STe100p",
> - .features = PHY_BASIC_FEATURES | SUPPORTED_Pause,
> + .features = PHY_BASIC_FEATURES,
> .flags = PHY_HAS_INTERRUPT,
> .config_init = ste10Xp_config_init,
> .ack_interrupt = ste10Xp_ack_interrupt,
>
--
Florian
^ permalink raw reply [flat|nested] 30+ messages in thread* Re: [PATCH net-next 01/12] net: phy: ste10Xp: Remove wrong SUPPORTED_Pause
2018-09-03 17:53 ` Florian Fainelli
@ 2018-09-04 1:20 ` Andrew Lunn
0 siblings, 0 replies; 30+ messages in thread
From: Andrew Lunn @ 2018-09-04 1:20 UTC (permalink / raw)
To: Florian Fainelli; +Cc: David Miller, netdev, maxime.chevallier
On Mon, Sep 03, 2018 at 10:53:58AM -0700, Florian Fainelli wrote:
>
>
> On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> >The PHY driver should not indicate that Pause is supported. It is upto
> >the MAC drive enable it, if it supports Pause frames. So remove it
> >from the ste10Xp driver.
>
> This came up before when Timur was cleaning up the Pause|ASym_Pause
> advertisment bits, and we agreed that a driver that cannot have the
> Asym_Pause bit writable, e.g: bcm63xx, would have to specifically leave
> SUPPORTED_Pause as a way to tell PHYLIB about that situation. See:
>
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/net/phy?id=529ed12752635ba8a35dc78ec70ed6f42570b4ca
>
> Can you check the datasheet if available?
Hi Florian
Datasheet is at:
https://www.st.com/resource/en/datasheet/ste100p.pdf
It indicates that bit 10 of the Auto-Neg advertisement for Pause is
R/W and defaults to 1. There is no support for Asym Pause, bit 11 is
reserved.
So we don't have the case of the bcm63xx. It should be that this PHY
supports plain symmetric Pause.
Andrew
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH net-next 02/12] net: phy: et1011c: Remove incorrect missing 1000 Half
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
2018-09-02 17:06 ` [PATCH net-next 01/12] net: phy: ste10Xp: Remove wrong SUPPORTED_Pause Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:46 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 03/12] net: phy: bcm63xx: Allow to be built with COMPILE_TEST Andrew Lunn
` (10 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
The driver indicates it can do 10/100 full and half duplex, plus 1G
Full. The datasheet indicates 1G half is also supported. So make use
of the standard PHY_GBIT_FEATURES.
It could be, this was added because there is a MAC which does not
support 1G half. Bit this is the wrong place to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/et1011c.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/phy/et1011c.c b/drivers/net/phy/et1011c.c
index a9a4edfa23c8..ab541c9c56fb 100644
--- a/drivers/net/phy/et1011c.c
+++ b/drivers/net/phy/et1011c.c
@@ -91,7 +91,7 @@ static struct phy_driver et1011c_driver[] = { {
.phy_id = 0x0282f014,
.name = "ET1011C",
.phy_id_mask = 0xfffffff0,
- .features = (PHY_BASIC_FEATURES | SUPPORTED_1000baseT_Full),
+ .features = PHY_GBIT_FEATURES,
.flags = PHY_POLL,
.config_aneg = et1011c_config_aneg,
.read_status = et1011c_read_status,
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [PATCH net-next 02/12] net: phy: et1011c: Remove incorrect missing 1000 Half
2018-09-02 17:06 ` [PATCH net-next 02/12] net: phy: et1011c: Remove incorrect missing 1000 Half Andrew Lunn
@ 2018-09-03 17:46 ` Florian Fainelli
0 siblings, 0 replies; 30+ messages in thread
From: Florian Fainelli @ 2018-09-03 17:46 UTC (permalink / raw)
To: Andrew Lunn, David Miller; +Cc: netdev, maxime.chevallier
On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> The driver indicates it can do 10/100 full and half duplex, plus 1G
> Full. The datasheet indicates 1G half is also supported. So make use
> of the standard PHY_GBIT_FEATURES.
>
> It could be, this was added because there is a MAC which does not
> support 1G half. Bit this is the wrong place to enforce this.
Indeed, this should not be left to the PHY to decide, although in my
experience using 1000/Half is always a "roll the dice" thing, since it
is not AFAIR properly specified.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
--
Florian
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH net-next 03/12] net: phy: bcm63xx: Allow to be built with COMPILE_TEST
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
2018-09-02 17:06 ` [PATCH net-next 01/12] net: phy: ste10Xp: Remove wrong SUPPORTED_Pause Andrew Lunn
2018-09-02 17:06 ` [PATCH net-next 02/12] net: phy: et1011c: Remove incorrect missing 1000 Half Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:28 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 04/12] net: ethernet: Use phy_set_max_speed() to limit advertised speed Andrew Lunn
` (9 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
There is nothing in this driver which prevents it to be compiled for
other architectures. Add COMPILE_TEST so we get better compile test
coverage.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 82070792edbb..3d187cd50eb0 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -240,7 +240,7 @@ config AT803X_PHY
config BCM63XX_PHY
tristate "Broadcom 63xx SOCs internal PHY"
- depends on BCM63XX
+ depends on BCM63XX || COMPILE_TEST
select BCM_NET_PHYLIB
---help---
Currently supports the 6348 and 6358 PHYs.
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [PATCH net-next 04/12] net: ethernet: Use phy_set_max_speed() to limit advertised speed
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (2 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 03/12] net: phy: bcm63xx: Allow to be built with COMPILE_TEST Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:31 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 05/12] net: ethernet: genet: Fix speed selection Andrew Lunn
` (8 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/8390/ax88796.c | 4 +---
drivers/net/ethernet/aeroflex/greth.c | 4 ++--
drivers/net/ethernet/agere/et131x.c | 12 ++----------
drivers/net/ethernet/allwinner/sun4i-emac.c | 3 +--
drivers/net/ethernet/altera/altera_tse_main.c | 5 +----
drivers/net/ethernet/amd/au1000_eth.c | 12 +-----------
drivers/net/ethernet/broadcom/bcm63xx_enet.c | 10 ++--------
drivers/net/ethernet/broadcom/genet/bcmmii.c | 2 +-
drivers/net/ethernet/broadcom/sb1250-mac.c | 11 ++---------
drivers/net/ethernet/broadcom/tg3.c | 8 ++++----
drivers/net/ethernet/cadence/macb_main.c | 4 ++--
drivers/net/ethernet/cortina/gemini.c | 2 +-
drivers/net/ethernet/dnet.c | 4 ++--
drivers/net/ethernet/ethoc.c | 5 +----
drivers/net/ethernet/freescale/fec_main.c | 4 ++--
drivers/net/ethernet/freescale/ucc_geth.c | 7 +------
drivers/net/ethernet/lantiq_etop.c | 11 ++---------
drivers/net/ethernet/mediatek/mtk_eth_soc.c | 4 ++--
drivers/net/ethernet/nxp/lpc_eth.c | 3 +--
drivers/net/ethernet/rdc/r6040.c | 12 ++----------
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c | 4 ++--
drivers/net/ethernet/smsc/smsc911x.c | 5 +++--
drivers/net/ethernet/smsc/smsc9420.c | 5 +++--
drivers/net/ethernet/socionext/sni_ave.c | 6 ++----
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 +--
drivers/net/ethernet/toshiba/tc35815.c | 2 +-
drivers/net/ethernet/xilinx/xilinx_emaclite.c | 3 +--
drivers/staging/mt7621-eth/mdio.c | 2 +-
28 files changed, 47 insertions(+), 110 deletions(-)
diff --git a/drivers/net/ethernet/8390/ax88796.c b/drivers/net/ethernet/8390/ax88796.c
index 2a0ddec1dd56..3dcc61821ed5 100644
--- a/drivers/net/ethernet/8390/ax88796.c
+++ b/drivers/net/ethernet/8390/ax88796.c
@@ -377,9 +377,7 @@ static int ax_mii_probe(struct net_device *dev)
return ret;
}
- /* mask with MAC supported features */
- phy_dev->supported &= PHY_BASIC_FEATURES;
- phy_dev->advertising = phy_dev->supported;
+ phy_set_max_speed(phy_dev, SPEED_100);
netdev_info(dev, "PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n",
phy_dev->drv->name, phydev_name(phy_dev), phy_dev->irq);
diff --git a/drivers/net/ethernet/aeroflex/greth.c b/drivers/net/ethernet/aeroflex/greth.c
index 4309be3724ad..7c9348a26cbb 100644
--- a/drivers/net/ethernet/aeroflex/greth.c
+++ b/drivers/net/ethernet/aeroflex/greth.c
@@ -1279,9 +1279,9 @@ static int greth_mdio_probe(struct net_device *dev)
}
if (greth->gbit_mac)
- phy->supported &= PHY_GBIT_FEATURES;
+ phy_set_max_speed(phy, SPEED_1000);
else
- phy->supported &= PHY_BASIC_FEATURES;
+ phy_set_max_speed(phy, SPEED_100);
phy->advertising = phy->supported;
diff --git a/drivers/net/ethernet/agere/et131x.c b/drivers/net/ethernet/agere/et131x.c
index 48220b6c600d..ea34bcb868b5 100644
--- a/drivers/net/ethernet/agere/et131x.c
+++ b/drivers/net/ethernet/agere/et131x.c
@@ -3258,19 +3258,11 @@ static int et131x_mii_probe(struct net_device *netdev)
return PTR_ERR(phydev);
}
- phydev->supported &= (SUPPORTED_10baseT_Half |
- SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full |
- SUPPORTED_Autoneg |
- SUPPORTED_MII |
- SUPPORTED_TP);
+ phy_set_max_speed(phydev, SPEED_100);
if (adapter->pdev->device != ET131X_PCI_DEVICE_ID_FAST)
- phydev->supported |= SUPPORTED_1000baseT_Half |
- SUPPORTED_1000baseT_Full;
+ phy_set_max_speed(phydev, SPEED_1000);
- phydev->advertising = phydev->supported;
phydev->autoneg = AUTONEG_ENABLE;
phy_attached_info(phydev);
diff --git a/drivers/net/ethernet/allwinner/sun4i-emac.c b/drivers/net/ethernet/allwinner/sun4i-emac.c
index 3143de45baaa..e1acafa82214 100644
--- a/drivers/net/ethernet/allwinner/sun4i-emac.c
+++ b/drivers/net/ethernet/allwinner/sun4i-emac.c
@@ -172,8 +172,7 @@ static int emac_mdio_probe(struct net_device *dev)
}
/* mask with MAC supported features */
- phydev->supported &= PHY_BASIC_FEATURES;
- phydev->advertising = phydev->supported;
+ phy_set_max_speed(phydev, SPEED_100);
db->link = 0;
db->speed = 0;
diff --git a/drivers/net/ethernet/altera/altera_tse_main.c b/drivers/net/ethernet/altera/altera_tse_main.c
index baca8f704a45..02921d877c08 100644
--- a/drivers/net/ethernet/altera/altera_tse_main.c
+++ b/drivers/net/ethernet/altera/altera_tse_main.c
@@ -835,13 +835,10 @@ static int init_phy(struct net_device *dev)
}
/* Stop Advertising 1000BASE Capability if interface is not GMII
- * Note: Checkpatch throws CHECKs for the camel case defines below,
- * it's ok to ignore.
*/
if ((priv->phy_iface == PHY_INTERFACE_MODE_MII) ||
(priv->phy_iface == PHY_INTERFACE_MODE_RMII))
- phydev->advertising &= ~(SUPPORTED_1000baseT_Half |
- SUPPORTED_1000baseT_Full);
+ phy_set_max_speed(phydev, SPEED_100);
/* Broken HW is sometimes missing the pull-up resistor on the
* MDIO line, which results in reads to non-existent devices returning
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index 73ca8879ada7..7c1eb304c27e 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -564,17 +564,7 @@ static int au1000_mii_probe(struct net_device *dev)
return PTR_ERR(phydev);
}
- /* mask with MAC supported features */
- phydev->supported &= (SUPPORTED_10baseT_Half
- | SUPPORTED_10baseT_Full
- | SUPPORTED_100baseT_Half
- | SUPPORTED_100baseT_Full
- | SUPPORTED_Autoneg
- /* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */
- | SUPPORTED_MII
- | SUPPORTED_TP);
-
- phydev->advertising = phydev->supported;
+ phy_set_max_speed(phydev, SPEED_100);
aup->old_link = 0;
aup->old_speed = 0;
diff --git a/drivers/net/ethernet/broadcom/bcm63xx_enet.c b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
index 897302adc38e..2eee9459c2cf 100644
--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
@@ -890,14 +890,8 @@ static int bcm_enet_open(struct net_device *dev)
}
/* mask with MAC supported features */
- phydev->supported &= (SUPPORTED_10baseT_Half |
- SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full |
- SUPPORTED_Autoneg |
- SUPPORTED_Pause |
- SUPPORTED_MII);
- phydev->advertising = phydev->supported;
+ phydev->supported |= SUPPORTED_Pause;
+ phy_set_max_speed(phydev, SPEED_100);
if (priv->pause_auto && priv->pause_rx && priv->pause_tx)
phydev->advertising |= SUPPORTED_Pause;
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index 5333274a283c..881e566730f3 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -208,7 +208,7 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
case PHY_INTERFACE_MODE_MII:
phy_name = "external MII";
- phydev->supported &= PHY_BASIC_FEATURES;
+ phy_set_max_speed(phydev, SPEED_100);
bcmgenet_sys_writel(priv,
PORT_MODE_EXT_EPHY, SYS_PORT_CTRL);
break;
diff --git a/drivers/net/ethernet/broadcom/sb1250-mac.c b/drivers/net/ethernet/broadcom/sb1250-mac.c
index ef4a0c326736..4ce4b097ec05 100644
--- a/drivers/net/ethernet/broadcom/sb1250-mac.c
+++ b/drivers/net/ethernet/broadcom/sb1250-mac.c
@@ -2357,15 +2357,8 @@ static int sbmac_mii_probe(struct net_device *dev)
}
/* Remove any features not supported by the controller */
- phy_dev->supported &= SUPPORTED_10baseT_Half |
- SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full |
- SUPPORTED_1000baseT_Half |
- SUPPORTED_1000baseT_Full |
- SUPPORTED_Autoneg |
- SUPPORTED_MII |
- SUPPORTED_Pause |
+ phy_set_max_speed(phy_dev, SPEED_1000);
+ phy_dev->supported |= SUPPORTED_Pause |
SUPPORTED_Asym_Pause;
phy_attached_info(phy_dev);
diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index e6f28c7942ab..cdc32724c9d9 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -2122,15 +2122,15 @@ static int tg3_phy_init(struct tg3 *tp)
case PHY_INTERFACE_MODE_GMII:
case PHY_INTERFACE_MODE_RGMII:
if (!(tp->phy_flags & TG3_PHYFLG_10_100_ONLY)) {
- phydev->supported &= (PHY_GBIT_FEATURES |
- SUPPORTED_Pause |
+ phy_set_max_speed(phydev, SPEED_1000);
+ phydev->supported &= (SUPPORTED_Pause |
SUPPORTED_Asym_Pause);
break;
}
/* fallthru */
case PHY_INTERFACE_MODE_MII:
- phydev->supported &= (PHY_BASIC_FEATURES |
- SUPPORTED_Pause |
+ phy_set_max_speed(phydev, SPEED_100);
+ phydev->supported &= (SUPPORTED_Pause |
SUPPORTED_Asym_Pause);
break;
default:
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index c6707ea2d751..2ece43cd9c9b 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -544,9 +544,9 @@ static int macb_mii_probe(struct net_device *dev)
/* mask with MAC supported features */
if (macb_is_gem(bp) && bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE)
- phydev->supported &= PHY_GBIT_FEATURES;
+ phy_set_max_speed(phydev, SPEED_1000);
else
- phydev->supported &= PHY_BASIC_FEATURES;
+ phy_set_max_speed(phydev, SPEED_100);
if (bp->caps & MACB_CAPS_NO_GIGABIT_HALF)
phydev->supported &= ~SUPPORTED_1000baseT_Half;
diff --git a/drivers/net/ethernet/cortina/gemini.c b/drivers/net/ethernet/cortina/gemini.c
index 1c9ad3630c77..2b46c0de90d0 100644
--- a/drivers/net/ethernet/cortina/gemini.c
+++ b/drivers/net/ethernet/cortina/gemini.c
@@ -372,7 +372,7 @@ static int gmac_setup_phy(struct net_device *netdev)
return -ENODEV;
netdev->phydev = phy;
- phy->supported &= PHY_GBIT_FEATURES;
+ phy_set_max_speed(phy, SPEED_1000);
phy->supported |= SUPPORTED_Asym_Pause | SUPPORTED_Pause;
phy->advertising = phy->supported;
diff --git a/drivers/net/ethernet/dnet.c b/drivers/net/ethernet/dnet.c
index 5a847941c46b..08b7ad1594ce 100644
--- a/drivers/net/ethernet/dnet.c
+++ b/drivers/net/ethernet/dnet.c
@@ -284,9 +284,9 @@ static int dnet_mii_probe(struct net_device *dev)
/* mask with MAC supported features */
if (bp->capabilities & DNET_HAS_GIGABIT)
- phydev->supported &= PHY_GBIT_FEATURES;
+ phy_set_max_speed(phydev, SPEED_1000);
else
- phydev->supported &= PHY_BASIC_FEATURES;
+ phy_set_max_speed(phydev, SPEED_100);
phydev->supported |= SUPPORTED_Asym_Pause | SUPPORTED_Pause;
diff --git a/drivers/net/ethernet/ethoc.c b/drivers/net/ethernet/ethoc.c
index 60da0499ad66..0f3e7f21c6fa 100644
--- a/drivers/net/ethernet/ethoc.c
+++ b/drivers/net/ethernet/ethoc.c
@@ -721,10 +721,7 @@ static int ethoc_mdio_probe(struct net_device *dev)
return err;
}
- phy->advertising &= ~(ADVERTISED_1000baseT_Full |
- ADVERTISED_1000baseT_Half);
- phy->supported &= ~(SUPPORTED_1000baseT_Full |
- SUPPORTED_1000baseT_Half);
+ phy_set_max_speed(phy, SPEED_100);
return 0;
}
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index 2708297e7795..5e849510c689 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -1946,14 +1946,14 @@ static int fec_enet_mii_probe(struct net_device *ndev)
/* mask with MAC supported features */
if (fep->quirks & FEC_QUIRK_HAS_GBIT) {
- phy_dev->supported &= PHY_GBIT_FEATURES;
+ phy_set_max_speed(phy_dev, 1000);
phy_dev->supported &= ~SUPPORTED_1000baseT_Half;
#if !defined(CONFIG_M5272)
phy_dev->supported |= SUPPORTED_Pause;
#endif
}
else
- phy_dev->supported &= PHY_BASIC_FEATURES;
+ phy_set_max_speed(phy_dev, 100);
phy_dev->advertising = phy_dev->supported;
diff --git a/drivers/net/ethernet/freescale/ucc_geth.c b/drivers/net/ethernet/freescale/ucc_geth.c
index 22a817da861e..9600837f21b8 100644
--- a/drivers/net/ethernet/freescale/ucc_geth.c
+++ b/drivers/net/ethernet/freescale/ucc_geth.c
@@ -1742,12 +1742,7 @@ static int init_phy(struct net_device *dev)
if (priv->phy_interface == PHY_INTERFACE_MODE_SGMII)
uec_configure_serdes(dev);
- phydev->supported &= (SUPPORTED_MII |
- SUPPORTED_Autoneg |
- ADVERTISED_10baseT_Half |
- ADVERTISED_10baseT_Full |
- ADVERTISED_100baseT_Half |
- ADVERTISED_100baseT_Full);
+ phy_set_max_speed(phydev, SPEED_100);
if (priv->max_speed == SPEED_1000)
phydev->supported |= ADVERTISED_1000baseT_Full;
diff --git a/drivers/net/ethernet/lantiq_etop.c b/drivers/net/ethernet/lantiq_etop.c
index 7a637b51c7d2..7b25ba957d3f 100644
--- a/drivers/net/ethernet/lantiq_etop.c
+++ b/drivers/net/ethernet/lantiq_etop.c
@@ -364,15 +364,8 @@ ltq_etop_mdio_probe(struct net_device *dev)
return PTR_ERR(phydev);
}
- phydev->supported &= (SUPPORTED_10baseT_Half
- | SUPPORTED_10baseT_Full
- | SUPPORTED_100baseT_Half
- | SUPPORTED_100baseT_Full
- | SUPPORTED_Autoneg
- | SUPPORTED_MII
- | SUPPORTED_TP);
-
- phydev->advertising = phydev->supported;
+ phy_set_max_speed(phydev, SPEED_100);
+
phy_attached_info(phydev);
return 0;
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index b44bcfd85b05..e93b5375504b 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -359,8 +359,8 @@ static int mtk_phy_connect(struct net_device *dev)
dev->phydev->supported |=
SUPPORTED_Pause | SUPPORTED_Asym_Pause;
- dev->phydev->supported &= PHY_GBIT_FEATURES | SUPPORTED_Pause |
- SUPPORTED_Asym_Pause;
+ phy_set_max_speed(dev->phydev, SPEED_1000);
+ dev->phydev->supported &= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
dev->phydev->advertising = dev->phydev->supported |
ADVERTISED_Autoneg;
phy_start_aneg(dev->phydev);
diff --git a/drivers/net/ethernet/nxp/lpc_eth.c b/drivers/net/ethernet/nxp/lpc_eth.c
index 08381ef8bdb4..8b23d2848457 100644
--- a/drivers/net/ethernet/nxp/lpc_eth.c
+++ b/drivers/net/ethernet/nxp/lpc_eth.c
@@ -797,8 +797,7 @@ static int lpc_mii_probe(struct net_device *ndev)
return PTR_ERR(phydev);
}
- /* mask with MAC supported features */
- phydev->supported &= PHY_BASIC_FEATURES;
+ phy_set_max_speed(phydev, SPEED_100);
phydev->advertising = phydev->supported;
diff --git a/drivers/net/ethernet/rdc/r6040.c b/drivers/net/ethernet/rdc/r6040.c
index aa11b70b9ca4..04aa592f35c3 100644
--- a/drivers/net/ethernet/rdc/r6040.c
+++ b/drivers/net/ethernet/rdc/r6040.c
@@ -1024,16 +1024,8 @@ static int r6040_mii_probe(struct net_device *dev)
return PTR_ERR(phydev);
}
- /* mask with MAC supported features */
- phydev->supported &= (SUPPORTED_10baseT_Half
- | SUPPORTED_10baseT_Full
- | SUPPORTED_100baseT_Half
- | SUPPORTED_100baseT_Full
- | SUPPORTED_Autoneg
- | SUPPORTED_MII
- | SUPPORTED_TP);
-
- phydev->advertising = phydev->supported;
+ phy_set_max_speed(phydev, SPEED_100);
+
lp->old_link = 0;
lp->old_duplex = -1;
diff --git a/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c b/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c
index a9da1ad4b4f2..690aee88f0eb 100644
--- a/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c
+++ b/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c
@@ -298,8 +298,8 @@ static int sxgbe_init_phy(struct net_device *ndev)
/* Stop Advertising 1000BASE Capability if interface is not GMII */
if ((phy_iface == PHY_INTERFACE_MODE_MII) ||
(phy_iface == PHY_INTERFACE_MODE_RMII))
- phydev->advertising &= ~(SUPPORTED_1000baseT_Half |
- SUPPORTED_1000baseT_Full);
+ phy_set_max_speed(phydev, SPEED_1000);
+
if (phydev->phy_id == 0) {
phy_disconnect(phydev);
return -ENODEV;
diff --git a/drivers/net/ethernet/smsc/smsc911x.c b/drivers/net/ethernet/smsc/smsc911x.c
index f0afb88d7bc2..f84dbd0beb8e 100644
--- a/drivers/net/ethernet/smsc/smsc911x.c
+++ b/drivers/net/ethernet/smsc/smsc911x.c
@@ -1048,9 +1048,10 @@ static int smsc911x_mii_probe(struct net_device *dev)
phy_attached_info(phydev);
+ phy_set_max_speed(phydev, SPEED_100);
+
/* mask with MAC supported features */
- phydev->supported &= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
- SUPPORTED_Asym_Pause);
+ phydev->supported &= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
phydev->advertising = phydev->supported;
pdata->last_duplex = -1;
diff --git a/drivers/net/ethernet/smsc/smsc9420.c b/drivers/net/ethernet/smsc/smsc9420.c
index 2fa3c1d03abc..795f60d92611 100644
--- a/drivers/net/ethernet/smsc/smsc9420.c
+++ b/drivers/net/ethernet/smsc/smsc9420.c
@@ -1135,9 +1135,10 @@ static int smsc9420_mii_probe(struct net_device *dev)
return PTR_ERR(phydev);
}
+ phy_set_max_speed(phydev, SPEED_100);
+
/* mask with MAC supported features */
- phydev->supported &= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
- SUPPORTED_Asym_Pause);
+ phydev->supported &= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
phydev->advertising = phydev->supported;
phy_attached_info(phydev);
diff --git a/drivers/net/ethernet/socionext/sni_ave.c b/drivers/net/ethernet/socionext/sni_ave.c
index f7ecceeb1e28..76ff364c40e9 100644
--- a/drivers/net/ethernet/socionext/sni_ave.c
+++ b/drivers/net/ethernet/socionext/sni_ave.c
@@ -1223,10 +1223,8 @@ static int ave_init(struct net_device *ndev)
phy_ethtool_get_wol(phydev, &wol);
device_set_wakeup_capable(&ndev->dev, !!wol.supported);
- if (!phy_interface_is_rgmii(phydev)) {
- phydev->supported &= ~PHY_GBIT_FEATURES;
- phydev->supported |= PHY_BASIC_FEATURES;
- }
+ if (!phy_interface_is_rgmii(phydev))
+ phy_set_max_speed(phydev, SPEED_100);
phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
phy_attached_info(phydev);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index ff1ffb46198a..3206728ed49f 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -987,8 +987,7 @@ static int stmmac_init_phy(struct net_device *dev)
if ((interface == PHY_INTERFACE_MODE_MII) ||
(interface == PHY_INTERFACE_MODE_RMII) ||
(max_speed < 1000 && max_speed > 0))
- phydev->advertising &= ~(SUPPORTED_1000baseT_Half |
- SUPPORTED_1000baseT_Full);
+ phy_set_max_speed(phydev, SPEED_100);
/*
* Half-duplex mode not supported with multiqueue
diff --git a/drivers/net/ethernet/toshiba/tc35815.c b/drivers/net/ethernet/toshiba/tc35815.c
index cce9c9ed46aa..7163a8d10dba 100644
--- a/drivers/net/ethernet/toshiba/tc35815.c
+++ b/drivers/net/ethernet/toshiba/tc35815.c
@@ -628,7 +628,7 @@ static int tc_mii_probe(struct net_device *dev)
phy_attached_info(phydev);
/* mask with MAC supported features */
- phydev->supported &= PHY_BASIC_FEATURES;
+ phy_set_max_speed(phydev, SPEED_100);
dropmask = 0;
if (options.speed == 10)
dropmask |= SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full;
diff --git a/drivers/net/ethernet/xilinx/xilinx_emaclite.c b/drivers/net/ethernet/xilinx/xilinx_emaclite.c
index 42f1f518dad6..46d3092b8aad 100644
--- a/drivers/net/ethernet/xilinx/xilinx_emaclite.c
+++ b/drivers/net/ethernet/xilinx/xilinx_emaclite.c
@@ -941,8 +941,7 @@ static int xemaclite_open(struct net_device *dev)
}
/* EmacLite doesn't support giga-bit speeds */
- lp->phy_dev->supported &= (PHY_BASIC_FEATURES);
- lp->phy_dev->advertising = lp->phy_dev->supported;
+ phy_set_max_speed(lp->phy_dev, SPEED_100);
/* Don't advertise 1000BASE-T Full/Half duplex speeds */
phy_write(lp->phy_dev, MII_CTRL1000, 0);
diff --git a/drivers/staging/mt7621-eth/mdio.c b/drivers/staging/mt7621-eth/mdio.c
index 7ad0c4141205..2c6e1800a3fd 100644
--- a/drivers/staging/mt7621-eth/mdio.c
+++ b/drivers/staging/mt7621-eth/mdio.c
@@ -112,7 +112,7 @@ static void phy_init(struct mtk_eth *eth, struct mtk_mac *mac,
phy->autoneg = AUTONEG_ENABLE;
phy->speed = 0;
phy->duplex = 0;
- phy->supported &= PHY_BASIC_FEATURES;
+ phy_set_max_speed(phy, SPEED_100);
phy->advertising = phy->supported | ADVERTISED_Autoneg;
phy_start_aneg(phy);
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [PATCH net-next 05/12] net: ethernet: genet: Fix speed selection
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (3 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 04/12] net: ethernet: Use phy_set_max_speed() to limit advertised speed Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:32 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 06/12] net: ethernet: Fix up drivers masking pause support Andrew Lunn
` (7 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
The phy supported speed is being used to determine if the MAC should
be configured to 100 or 1G. The masking logic is broken. Instead, look
1G supported speeds to enable 1G MAC support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/broadcom/genet/bcmmii.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index 881e566730f3..69587a61e8d6 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -220,11 +220,10 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
* capabilities, use that knowledge to also configure the
* Reverse MII interface correctly.
*/
- if ((dev->phydev->supported & PHY_BASIC_FEATURES) ==
- PHY_BASIC_FEATURES)
- port_ctrl = PORT_MODE_EXT_RVMII_25;
- else
+ if (dev->phydev->supported & PHY_1000BT_FEATURES)
port_ctrl = PORT_MODE_EXT_RVMII_50;
+ else
+ port_ctrl = PORT_MODE_EXT_RVMII_25;
bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL);
break;
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [PATCH net-next 05/12] net: ethernet: genet: Fix speed selection
2018-09-02 17:06 ` [PATCH net-next 05/12] net: ethernet: genet: Fix speed selection Andrew Lunn
@ 2018-09-03 17:32 ` Florian Fainelli
0 siblings, 0 replies; 30+ messages in thread
From: Florian Fainelli @ 2018-09-03 17:32 UTC (permalink / raw)
To: Andrew Lunn, David Miller; +Cc: netdev, maxime.chevallier
On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> The phy supported speed is being used to determine if the MAC should
> be configured to 100 or 1G. The masking logic is broken. Instead, look
> 1G supported speeds to enable 1G MAC support.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> ---
> drivers/net/ethernet/broadcom/genet/bcmmii.c | 7 +++----
> 1 file changed, 3 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
> index 881e566730f3..69587a61e8d6 100644
> --- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
> +++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
> @@ -220,11 +220,10 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
> * capabilities, use that knowledge to also configure the
> * Reverse MII interface correctly.
> */
> - if ((dev->phydev->supported & PHY_BASIC_FEATURES) ==
> - PHY_BASIC_FEATURES)
> - port_ctrl = PORT_MODE_EXT_RVMII_25;
> - else
> + if (dev->phydev->supported & PHY_1000BT_FEATURES)
> port_ctrl = PORT_MODE_EXT_RVMII_50;
> + else
> + port_ctrl = PORT_MODE_EXT_RVMII_25;
Your change is not wrong, but the driver was wrong previously, reverse
MII is 10/100 only, but the reference clock selection (25Mhz or 50Mhz)
cannot be automatically discovered and we need the help of Device
Tree/platform data here. I will submit a separate patch for "net", and
this one can go in for now.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
--
Florian
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH net-next 06/12] net: ethernet: Fix up drivers masking pause support
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (4 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 05/12] net: ethernet: genet: Fix speed selection Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:33 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 07/12] net: ethernet: Add helper to remove a supported link mode Andrew Lunn
` (6 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
PHY drivers don't indicate they support pause. They expect MAC drivers
to enable its support if the MAC has the needed hardware. Thus MAC
drivers should not mask Pause support, but enable it.
Change a few ANDs to ORs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/broadcom/tg3.c | 4 ++--
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c | 4 ++--
drivers/net/ethernet/mediatek/mtk_eth_soc.c | 2 +-
drivers/net/ethernet/smsc/smsc911x.c | 2 +-
drivers/net/ethernet/smsc/smsc9420.c | 2 +-
5 files changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index cdc32724c9d9..eab00239a47a 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -2123,14 +2123,14 @@ static int tg3_phy_init(struct tg3 *tp)
case PHY_INTERFACE_MODE_RGMII:
if (!(tp->phy_flags & TG3_PHYFLG_10_100_ONLY)) {
phy_set_max_speed(phydev, SPEED_1000);
- phydev->supported &= (SUPPORTED_Pause |
+ phydev->supported |= (SUPPORTED_Pause |
SUPPORTED_Asym_Pause);
break;
}
/* fallthru */
case PHY_INTERFACE_MODE_MII:
phy_set_max_speed(phydev, SPEED_100);
- phydev->supported &= (SUPPORTED_Pause |
+ phydev->supported |= (SUPPORTED_Pause |
SUPPORTED_Asym_Pause);
break;
default:
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
index 398971a062f4..05b15d254e32 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
@@ -10,8 +10,6 @@
#define HCLGE_PHY_SUPPORTED_FEATURES (SUPPORTED_Autoneg | \
SUPPORTED_TP | \
- SUPPORTED_Pause | \
- SUPPORTED_Asym_Pause | \
PHY_10BT_FEATURES | \
PHY_100BT_FEATURES | \
PHY_1000BT_FEATURES)
@@ -213,6 +211,8 @@ int hclge_mac_connect_phy(struct hclge_dev *hdev)
}
phydev->supported &= HCLGE_PHY_SUPPORTED_FEATURES;
+ phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
+
phydev->advertising = phydev->supported;
return 0;
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index e93b5375504b..db231bda7c2a 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -360,7 +360,7 @@ static int mtk_phy_connect(struct net_device *dev)
SUPPORTED_Pause | SUPPORTED_Asym_Pause;
phy_set_max_speed(dev->phydev, SPEED_1000);
- dev->phydev->supported &= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
+ dev->phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
dev->phydev->advertising = dev->phydev->supported |
ADVERTISED_Autoneg;
phy_start_aneg(dev->phydev);
diff --git a/drivers/net/ethernet/smsc/smsc911x.c b/drivers/net/ethernet/smsc/smsc911x.c
index f84dbd0beb8e..3e34bf53f055 100644
--- a/drivers/net/ethernet/smsc/smsc911x.c
+++ b/drivers/net/ethernet/smsc/smsc911x.c
@@ -1051,7 +1051,7 @@ static int smsc911x_mii_probe(struct net_device *dev)
phy_set_max_speed(phydev, SPEED_100);
/* mask with MAC supported features */
- phydev->supported &= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
+ phydev->supported |= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
phydev->advertising = phydev->supported;
pdata->last_duplex = -1;
diff --git a/drivers/net/ethernet/smsc/smsc9420.c b/drivers/net/ethernet/smsc/smsc9420.c
index 795f60d92611..326177384544 100644
--- a/drivers/net/ethernet/smsc/smsc9420.c
+++ b/drivers/net/ethernet/smsc/smsc9420.c
@@ -1138,7 +1138,7 @@ static int smsc9420_mii_probe(struct net_device *dev)
phy_set_max_speed(phydev, SPEED_100);
/* mask with MAC supported features */
- phydev->supported &= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
+ phydev->supported |= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
phydev->advertising = phydev->supported;
phy_attached_info(phydev);
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [PATCH net-next 06/12] net: ethernet: Fix up drivers masking pause support
2018-09-02 17:06 ` [PATCH net-next 06/12] net: ethernet: Fix up drivers masking pause support Andrew Lunn
@ 2018-09-03 17:33 ` Florian Fainelli
0 siblings, 0 replies; 30+ messages in thread
From: Florian Fainelli @ 2018-09-03 17:33 UTC (permalink / raw)
To: Andrew Lunn, David Miller, michael.chan; +Cc: netdev, maxime.chevallier
On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> PHY drivers don't indicate they support pause. They expect MAC drivers
> to enable its support if the MAC has the needed hardware. Thus MAC
> drivers should not mask Pause support, but enable it.
>
> Change a few ANDs to ORs.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Adding Michael for tg3.c
> ---
> drivers/net/ethernet/broadcom/tg3.c | 4 ++--
> drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c | 4 ++--
> drivers/net/ethernet/mediatek/mtk_eth_soc.c | 2 +-
> drivers/net/ethernet/smsc/smsc911x.c | 2 +-
> drivers/net/ethernet/smsc/smsc9420.c | 2 +-
> 5 files changed, 7 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
> index cdc32724c9d9..eab00239a47a 100644
> --- a/drivers/net/ethernet/broadcom/tg3.c
> +++ b/drivers/net/ethernet/broadcom/tg3.c
> @@ -2123,14 +2123,14 @@ static int tg3_phy_init(struct tg3 *tp)
> case PHY_INTERFACE_MODE_RGMII:
> if (!(tp->phy_flags & TG3_PHYFLG_10_100_ONLY)) {
> phy_set_max_speed(phydev, SPEED_1000);
> - phydev->supported &= (SUPPORTED_Pause |
> + phydev->supported |= (SUPPORTED_Pause |
> SUPPORTED_Asym_Pause);
> break;
> }
> /* fallthru */
> case PHY_INTERFACE_MODE_MII:
> phy_set_max_speed(phydev, SPEED_100);
> - phydev->supported &= (SUPPORTED_Pause |
> + phydev->supported |= (SUPPORTED_Pause |
> SUPPORTED_Asym_Pause);
> break;
> default:
> diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
> index 398971a062f4..05b15d254e32 100644
> --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
> +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
> @@ -10,8 +10,6 @@
>
> #define HCLGE_PHY_SUPPORTED_FEATURES (SUPPORTED_Autoneg | \
> SUPPORTED_TP | \
> - SUPPORTED_Pause | \
> - SUPPORTED_Asym_Pause | \
> PHY_10BT_FEATURES | \
> PHY_100BT_FEATURES | \
> PHY_1000BT_FEATURES)
> @@ -213,6 +211,8 @@ int hclge_mac_connect_phy(struct hclge_dev *hdev)
> }
>
> phydev->supported &= HCLGE_PHY_SUPPORTED_FEATURES;
> + phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
> +
> phydev->advertising = phydev->supported;
>
> return 0;
> diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
> index e93b5375504b..db231bda7c2a 100644
> --- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
> +++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
> @@ -360,7 +360,7 @@ static int mtk_phy_connect(struct net_device *dev)
> SUPPORTED_Pause | SUPPORTED_Asym_Pause;
>
> phy_set_max_speed(dev->phydev, SPEED_1000);
> - dev->phydev->supported &= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
> + dev->phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
> dev->phydev->advertising = dev->phydev->supported |
> ADVERTISED_Autoneg;
> phy_start_aneg(dev->phydev);
> diff --git a/drivers/net/ethernet/smsc/smsc911x.c b/drivers/net/ethernet/smsc/smsc911x.c
> index f84dbd0beb8e..3e34bf53f055 100644
> --- a/drivers/net/ethernet/smsc/smsc911x.c
> +++ b/drivers/net/ethernet/smsc/smsc911x.c
> @@ -1051,7 +1051,7 @@ static int smsc911x_mii_probe(struct net_device *dev)
> phy_set_max_speed(phydev, SPEED_100);
>
> /* mask with MAC supported features */
> - phydev->supported &= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
> + phydev->supported |= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
> phydev->advertising = phydev->supported;
>
> pdata->last_duplex = -1;
> diff --git a/drivers/net/ethernet/smsc/smsc9420.c b/drivers/net/ethernet/smsc/smsc9420.c
> index 795f60d92611..326177384544 100644
> --- a/drivers/net/ethernet/smsc/smsc9420.c
> +++ b/drivers/net/ethernet/smsc/smsc9420.c
> @@ -1138,7 +1138,7 @@ static int smsc9420_mii_probe(struct net_device *dev)
> phy_set_max_speed(phydev, SPEED_100);
>
> /* mask with MAC supported features */
> - phydev->supported &= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
> + phydev->supported |= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
> phydev->advertising = phydev->supported;
>
> phy_attached_info(phydev);
>
--
Florian
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH net-next 07/12] net: ethernet: Add helper to remove a supported link mode
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (5 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 06/12] net: ethernet: Fix up drivers masking pause support Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:35 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 08/12] net: ethernet: Add helper for MACs which support asym pause Andrew Lunn
` (5 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c | 6 +++---
drivers/net/ethernet/cadence/macb_main.c | 5 ++---
drivers/net/ethernet/freescale/fec_main.c | 3 ++-
drivers/net/ethernet/microchip/lan743x_main.c | 2 +-
drivers/net/ethernet/renesas/ravb_main.c | 3 ++-
.../net/ethernet/stmicro/stmmac/stmmac_main.c | 12 ++++++++----
drivers/net/phy/phy_device.c | 18 ++++++++++++++++++
drivers/net/usb/lan78xx.c | 2 +-
include/linux/phy.h | 1 +
9 files changed, 38 insertions(+), 14 deletions(-)
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
index 078a04dc1182..4831f9de5945 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
@@ -895,9 +895,9 @@ int xgene_enet_phy_connect(struct net_device *ndev)
}
pdata->phy_speed = SPEED_UNKNOWN;
- phy_dev->supported &= ~SUPPORTED_10baseT_Half &
- ~SUPPORTED_100baseT_Half &
- ~SUPPORTED_1000baseT_Half;
+ phy_remove_link_mode(phy_dev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+ phy_remove_link_mode(phy_dev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
+ phy_remove_link_mode(phy_dev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
phy_dev->supported |= SUPPORTED_Pause |
SUPPORTED_Asym_Pause;
phy_dev->advertising = phy_dev->supported;
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index 2ece43cd9c9b..4ececc20eeb2 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -549,9 +549,8 @@ static int macb_mii_probe(struct net_device *dev)
phy_set_max_speed(phydev, SPEED_100);
if (bp->caps & MACB_CAPS_NO_GIGABIT_HALF)
- phydev->supported &= ~SUPPORTED_1000baseT_Half;
-
- phydev->advertising = phydev->supported;
+ phy_remove_link_mode(phydev,
+ ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
bp->link = 0;
bp->speed = 0;
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index 5e849510c689..0c6fd77b6599 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -1947,7 +1947,8 @@ static int fec_enet_mii_probe(struct net_device *ndev)
/* mask with MAC supported features */
if (fep->quirks & FEC_QUIRK_HAS_GBIT) {
phy_set_max_speed(phy_dev, 1000);
- phy_dev->supported &= ~SUPPORTED_1000baseT_Half;
+ phy_remove_link_mode(phy_dev,
+ ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
#if !defined(CONFIG_M5272)
phy_dev->supported |= SUPPORTED_Pause;
#endif
diff --git a/drivers/net/ethernet/microchip/lan743x_main.c b/drivers/net/ethernet/microchip/lan743x_main.c
index e7dce79ff2c9..048307959c01 100644
--- a/drivers/net/ethernet/microchip/lan743x_main.c
+++ b/drivers/net/ethernet/microchip/lan743x_main.c
@@ -1013,7 +1013,7 @@ static int lan743x_phy_open(struct lan743x_adapter *adapter)
goto return_error;
/* MAC doesn't support 1000T Half */
- phydev->supported &= ~SUPPORTED_1000baseT_Half;
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
/* support both flow controls */
phy->fc_request_control = (FLOW_CTRL_RX | FLOW_CTRL_TX);
diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c
index aff5516b781e..fb2a1125780d 100644
--- a/drivers/net/ethernet/renesas/ravb_main.c
+++ b/drivers/net/ethernet/renesas/ravb_main.c
@@ -1074,7 +1074,8 @@ static int ravb_phy_init(struct net_device *ndev)
}
/* 10BASE is not supported */
- phydev->supported &= ~PHY_10BT_FEATURES;
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Full_BIT);
phy_attached_info(phydev);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 3206728ed49f..f77e051b557d 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -993,10 +993,14 @@ static int stmmac_init_phy(struct net_device *dev)
* Half-duplex mode not supported with multiqueue
* half-duplex can only works with single queue
*/
- if (tx_cnt > 1)
- phydev->supported &= ~(SUPPORTED_1000baseT_Half |
- SUPPORTED_100baseT_Half |
- SUPPORTED_10baseT_Half);
+ if (tx_cnt > 1) {
+ phy_remove_link_mode(phydev,
+ ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+ phy_remove_link_mode(phydev,
+ ETHTOOL_LINK_MODE_100baseT_Half_BIT);
+ phy_remove_link_mode(phydev,
+ ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+ }
/*
* Broken HW is sometimes missing the pull-up resistor on the
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index db1172db1e7c..e9ca83a438b0 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1765,6 +1765,24 @@ int phy_set_max_speed(struct phy_device *phydev, u32 max_speed)
}
EXPORT_SYMBOL(phy_set_max_speed);
+/**
+ * phy_remove_link_mode - Remove a supported link mode
+ * @phydev: phy_device structure to remove link mode from
+ * @link_mode: Link mode to be removed
+ *
+ * Description: Some MACs don't support all link modes which the PHY
+ * does. e.g. a 1G MAC often does not support 1000Half. Add a helper
+ * to remove a link mode.
+ */
+void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode)
+{
+ WARN_ON(link_mode > 31);
+
+ phydev->supported &= ~BIT(link_mode);
+ phydev->advertising = phydev->supported;
+}
+EXPORT_SYMBOL(phy_remove_link_mode);
+
static void of_set_phy_supported(struct phy_device *phydev)
{
struct device_node *node = phydev->mdio.dev.of_node;
diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c
index a9991c5f4736..cc91207eef89 100644
--- a/drivers/net/usb/lan78xx.c
+++ b/drivers/net/usb/lan78xx.c
@@ -2178,7 +2178,7 @@ static int lan78xx_phy_init(struct lan78xx_net *dev)
}
/* MAC doesn't support 1000T Half */
- phydev->supported &= ~SUPPORTED_1000baseT_Half;
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
/* support both flow controls */
dev->fc_request_control = (FLOW_CTRL_RX | FLOW_CTRL_TX);
diff --git a/include/linux/phy.h b/include/linux/phy.h
index cd6f637cbbfb..9c4c3eca8cf2 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1049,6 +1049,7 @@ int phy_mii_ioctl(struct phy_device *phydev, struct ifreq *ifr, int cmd);
int phy_start_interrupts(struct phy_device *phydev);
void phy_print_status(struct phy_device *phydev);
int phy_set_max_speed(struct phy_device *phydev, u32 max_speed);
+void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode);
int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask,
int (*run)(struct phy_device *));
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [PATCH net-next 08/12] net: ethernet: Add helper for MACs which support asym pause
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (6 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 07/12] net: ethernet: Add helper to remove a supported link mode Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:38 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 09/12] net: ethernet: Add helper for MACs which support pause Andrew Lunn
` (4 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c | 4 ++--
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c | 4 +---
drivers/net/ethernet/broadcom/sb1250-mac.c | 5 +----
drivers/net/ethernet/broadcom/tg3.c | 8 ++------
drivers/net/ethernet/cortina/gemini.c | 3 +--
drivers/net/ethernet/dnet.c | 4 +---
drivers/net/ethernet/faraday/ftgmac100.c | 3 +--
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c | 3 +--
drivers/net/ethernet/freescale/gianfar.c | 4 ++--
.../net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c | 4 +---
drivers/net/ethernet/mediatek/mtk_eth_soc.c | 6 +-----
drivers/net/ethernet/microchip/lan743x_main.c | 5 +----
drivers/net/ethernet/smsc/smsc911x.c | 3 +--
drivers/net/ethernet/smsc/smsc9420.c | 3 +--
drivers/net/ethernet/socionext/sni_ave.c | 3 ++-
drivers/net/phy/phy_device.c | 13 +++++++++++++
include/linux/phy.h | 1 +
17 files changed, 33 insertions(+), 43 deletions(-)
diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c b/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
index 3ceb4f95ca7c..289129011b9f 100644
--- a/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
+++ b/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
@@ -879,8 +879,8 @@ static bool xgbe_phy_finisar_phy_quirks(struct xgbe_prv_data *pdata)
phy_write(phy_data->phydev, 0x00, 0x9140);
phy_data->phydev->supported = PHY_GBIT_FEATURES;
- phy_data->phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
phy_data->phydev->advertising = phy_data->phydev->supported;
+ phy_support_asym_pause(phy_data->phydev);
netif_dbg(pdata, drv, pdata->netdev,
"Finisar PHY quirk in place\n");
@@ -951,8 +951,8 @@ static bool xgbe_phy_belfuse_phy_quirks(struct xgbe_prv_data *pdata)
phy_write(phy_data->phydev, 0x00, reg & ~0x00800);
phy_data->phydev->supported = PHY_GBIT_FEATURES;
- phy_data->phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
phy_data->phydev->advertising = phy_data->phydev->supported;
+ phy_support_asym_pause(phy_data->phydev);
netif_dbg(pdata, drv, pdata->netdev,
"BelFuse PHY quirk in place\n");
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
index 4831f9de5945..e3560311711a 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
@@ -898,9 +898,7 @@ int xgene_enet_phy_connect(struct net_device *ndev)
phy_remove_link_mode(phy_dev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
phy_remove_link_mode(phy_dev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
phy_remove_link_mode(phy_dev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
- phy_dev->supported |= SUPPORTED_Pause |
- SUPPORTED_Asym_Pause;
- phy_dev->advertising = phy_dev->supported;
+ phy_support_asym_pause(phy_dev);
return 0;
}
diff --git a/drivers/net/ethernet/broadcom/sb1250-mac.c b/drivers/net/ethernet/broadcom/sb1250-mac.c
index 4ce4b097ec05..53acbbb36637 100644
--- a/drivers/net/ethernet/broadcom/sb1250-mac.c
+++ b/drivers/net/ethernet/broadcom/sb1250-mac.c
@@ -2358,13 +2358,10 @@ static int sbmac_mii_probe(struct net_device *dev)
/* Remove any features not supported by the controller */
phy_set_max_speed(phy_dev, SPEED_1000);
- phy_dev->supported |= SUPPORTED_Pause |
- SUPPORTED_Asym_Pause;
+ phy_support_asym_pause(phy_dev);
phy_attached_info(phy_dev);
- phy_dev->advertising = phy_dev->supported;
-
sc->phy_dev = phy_dev;
return 0;
diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index eab00239a47a..9aa7955d5d31 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -2123,15 +2123,13 @@ static int tg3_phy_init(struct tg3 *tp)
case PHY_INTERFACE_MODE_RGMII:
if (!(tp->phy_flags & TG3_PHYFLG_10_100_ONLY)) {
phy_set_max_speed(phydev, SPEED_1000);
- phydev->supported |= (SUPPORTED_Pause |
- SUPPORTED_Asym_Pause);
+ phy_support_asym_pause(phydev);
break;
}
/* fallthru */
case PHY_INTERFACE_MODE_MII:
phy_set_max_speed(phydev, SPEED_100);
- phydev->supported |= (SUPPORTED_Pause |
- SUPPORTED_Asym_Pause);
+ phy_support_asym_pause(phydev);
break;
default:
phy_disconnect(mdiobus_get_phy(tp->mdio_bus, tp->phy_addr));
@@ -2140,8 +2138,6 @@ static int tg3_phy_init(struct tg3 *tp)
tp->phy_flags |= TG3_PHYFLG_IS_CONNECTED;
- phydev->advertising = phydev->supported;
-
phy_attached_info(phydev);
return 0;
diff --git a/drivers/net/ethernet/cortina/gemini.c b/drivers/net/ethernet/cortina/gemini.c
index 2b46c0de90d0..ceec467f590d 100644
--- a/drivers/net/ethernet/cortina/gemini.c
+++ b/drivers/net/ethernet/cortina/gemini.c
@@ -373,8 +373,7 @@ static int gmac_setup_phy(struct net_device *netdev)
netdev->phydev = phy;
phy_set_max_speed(phy, SPEED_1000);
- phy->supported |= SUPPORTED_Asym_Pause | SUPPORTED_Pause;
- phy->advertising = phy->supported;
+ phy_support_asym_pause(phy);
/* set PHY interface type */
switch (phy->interface) {
diff --git a/drivers/net/ethernet/dnet.c b/drivers/net/ethernet/dnet.c
index 08b7ad1594ce..79521e27f0d1 100644
--- a/drivers/net/ethernet/dnet.c
+++ b/drivers/net/ethernet/dnet.c
@@ -288,9 +288,7 @@ static int dnet_mii_probe(struct net_device *dev)
else
phy_set_max_speed(phydev, SPEED_100);
- phydev->supported |= SUPPORTED_Asym_Pause | SUPPORTED_Pause;
-
- phydev->advertising = phydev->supported;
+ phy_support_asym_pause(phydev);
bp->link = 0;
bp->speed = 0;
diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index ed6c76d20b45..3f319ee66ab4 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -1079,8 +1079,7 @@ static int ftgmac100_mii_probe(struct ftgmac100 *priv, phy_interface_t intf)
/* Indicate that we support PAUSE frames (see comment in
* Documentation/networking/phy.txt)
*/
- phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
- phydev->advertising = phydev->supported;
+ phy_support_asym_pause(phydev);
/* Display what we found */
phy_attached_info(phydev);
diff --git a/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c b/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
index 65a22cd9aef2..fc841e17fec0 100644
--- a/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
+++ b/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
@@ -2493,8 +2493,7 @@ static int dpaa_phy_init(struct net_device *net_dev)
/* Remove any features not supported by the controller */
phy_dev->supported &= mac_dev->if_support;
- phy_dev->supported |= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
- phy_dev->advertising = phy_dev->supported;
+ phy_support_asym_pause(phy_dev);
mac_dev->phy_dev = phy_dev;
net_dev->phydev = phy_dev;
diff --git a/drivers/net/ethernet/freescale/gianfar.c b/drivers/net/ethernet/freescale/gianfar.c
index f27f9bae1a4a..40a1a87cd338 100644
--- a/drivers/net/ethernet/freescale/gianfar.c
+++ b/drivers/net/ethernet/freescale/gianfar.c
@@ -1814,8 +1814,8 @@ static int init_phy(struct net_device *dev)
phydev->supported &= (GFAR_SUPPORTED | gigabit_support);
phydev->advertising = phydev->supported;
- /* Add support for flow control, but don't advertise it by default */
- phydev->supported |= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
+ /* Add support for flow control */
+ phy_support_asym_pause(phydev);
/* disable EEE autoneg, EEE not supported by eTSEC */
memset(&edata, 0, sizeof(struct ethtool_eee));
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
index 05b15d254e32..24b1f2a0c32a 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
@@ -211,9 +211,7 @@ int hclge_mac_connect_phy(struct hclge_dev *hdev)
}
phydev->supported &= HCLGE_PHY_SUPPORTED_FEATURES;
- phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
-
- phydev->advertising = phydev->supported;
+ phy_support_asym_pause(phydev);
return 0;
}
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index db231bda7c2a..cc1e9a96a43b 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -355,12 +355,8 @@ static int mtk_phy_connect(struct net_device *dev)
dev->phydev->speed = 0;
dev->phydev->duplex = 0;
- if (of_phy_is_fixed_link(mac->of_node))
- dev->phydev->supported |=
- SUPPORTED_Pause | SUPPORTED_Asym_Pause;
-
phy_set_max_speed(dev->phydev, SPEED_1000);
- dev->phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
+ phy_support_asym_pause(dev->phydev);
dev->phydev->advertising = dev->phydev->supported |
ADVERTISED_Autoneg;
phy_start_aneg(dev->phydev);
diff --git a/drivers/net/ethernet/microchip/lan743x_main.c b/drivers/net/ethernet/microchip/lan743x_main.c
index 048307959c01..b1a0e657febf 100644
--- a/drivers/net/ethernet/microchip/lan743x_main.c
+++ b/drivers/net/ethernet/microchip/lan743x_main.c
@@ -999,7 +999,6 @@ static int lan743x_phy_open(struct lan743x_adapter *adapter)
struct phy_device *phydev;
struct net_device *netdev;
int ret = -EIO;
- u32 mii_adv;
netdev = adapter->netdev;
phydev = phy_find_first(adapter->mdiobus);
@@ -1016,10 +1015,8 @@ static int lan743x_phy_open(struct lan743x_adapter *adapter)
phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
/* support both flow controls */
+ phy_support_asym_pause(phydev);
phy->fc_request_control = (FLOW_CTRL_RX | FLOW_CTRL_TX);
- phydev->advertising &= ~(ADVERTISED_Pause | ADVERTISED_Asym_Pause);
- mii_adv = (u32)mii_advertise_flowctrl(phy->fc_request_control);
- phydev->advertising |= mii_adv_to_ethtool_adv_t(mii_adv);
phy->fc_autoneg = phydev->autoneg;
phy_start(phydev);
diff --git a/drivers/net/ethernet/smsc/smsc911x.c b/drivers/net/ethernet/smsc/smsc911x.c
index 3e34bf53f055..c009407618d9 100644
--- a/drivers/net/ethernet/smsc/smsc911x.c
+++ b/drivers/net/ethernet/smsc/smsc911x.c
@@ -1051,8 +1051,7 @@ static int smsc911x_mii_probe(struct net_device *dev)
phy_set_max_speed(phydev, SPEED_100);
/* mask with MAC supported features */
- phydev->supported |= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
- phydev->advertising = phydev->supported;
+ phy_support_asym_pause(phydev);
pdata->last_duplex = -1;
pdata->last_carrier = -1;
diff --git a/drivers/net/ethernet/smsc/smsc9420.c b/drivers/net/ethernet/smsc/smsc9420.c
index 326177384544..9b6366b20110 100644
--- a/drivers/net/ethernet/smsc/smsc9420.c
+++ b/drivers/net/ethernet/smsc/smsc9420.c
@@ -1138,8 +1138,7 @@ static int smsc9420_mii_probe(struct net_device *dev)
phy_set_max_speed(phydev, SPEED_100);
/* mask with MAC supported features */
- phydev->supported |= (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
- phydev->advertising = phydev->supported;
+ phy_support_asym_pause(phydev);
phy_attached_info(phydev);
diff --git a/drivers/net/ethernet/socionext/sni_ave.c b/drivers/net/ethernet/socionext/sni_ave.c
index 76ff364c40e9..a50720ec109c 100644
--- a/drivers/net/ethernet/socionext/sni_ave.c
+++ b/drivers/net/ethernet/socionext/sni_ave.c
@@ -1225,7 +1225,8 @@ static int ave_init(struct net_device *ndev)
if (!phy_interface_is_rgmii(phydev))
phy_set_max_speed(phydev, SPEED_100);
- phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
+
+ phy_support_asym_pause(phydev);
phy_attached_info(phydev);
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index e9ca83a438b0..a0646a66f005 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1783,6 +1783,19 @@ void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode)
}
EXPORT_SYMBOL(phy_remove_link_mode);
+/**
+ * phy_support_asym_pause - Enable support of asym pause
+ * @phydev: target phy_device struct
+ *
+ * Description: Called by the MAC to indicate is supports Asym Pause.
+ */
+void phy_support_asym_pause(struct phy_device *phydev)
+{
+ phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
+ phydev->advertising = phydev->supported;
+}
+EXPORT_SYMBOL(phy_support_asym_pause);
+
static void of_set_phy_supported(struct phy_device *phydev)
{
struct device_node *node = phydev->mdio.dev.of_node;
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 9c4c3eca8cf2..e2db819807c1 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1050,6 +1050,7 @@ int phy_start_interrupts(struct phy_device *phydev);
void phy_print_status(struct phy_device *phydev);
int phy_set_max_speed(struct phy_device *phydev, u32 max_speed);
void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode);
+void phy_support_asym_pause(struct phy_device *phydev);
int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask,
int (*run)(struct phy_device *));
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [PATCH net-next 08/12] net: ethernet: Add helper for MACs which support asym pause
2018-09-02 17:06 ` [PATCH net-next 08/12] net: ethernet: Add helper for MACs which support asym pause Andrew Lunn
@ 2018-09-03 17:38 ` Florian Fainelli
0 siblings, 0 replies; 30+ messages in thread
From: Florian Fainelli @ 2018-09-03 17:38 UTC (permalink / raw)
To: Andrew Lunn, David Miller; +Cc: netdev, maxime.chevallier
On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> Rather than have the MAC drivers manipulate phydev members to indicate
> they support Asym Pause, add a helper function.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Just one nit in tg3.c:
> diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
> index eab00239a47a..9aa7955d5d31 100644
> --- a/drivers/net/ethernet/broadcom/tg3.c
> +++ b/drivers/net/ethernet/broadcom/tg3.c
> @@ -2123,15 +2123,13 @@ static int tg3_phy_init(struct tg3 *tp)
> case PHY_INTERFACE_MODE_RGMII:
> if (!(tp->phy_flags & TG3_PHYFLG_10_100_ONLY)) {
> phy_set_max_speed(phydev, SPEED_1000);
> - phydev->supported |= (SUPPORTED_Pause |
> - SUPPORTED_Asym_Pause);
> + phy_support_asym_pause(phydev);
> break;
> }
> /* fallthru */
> case PHY_INTERFACE_MODE_MII:
> phy_set_max_speed(phydev, SPEED_100);
> - phydev->supported |= (SUPPORTED_Pause |
> - SUPPORTED_Asym_Pause);
> + phy_support_asym_pause(phydev);
Your indentation is off by a tab here.
--
Florian
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH net-next 09/12] net: ethernet: Add helper for MACs which support pause
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (7 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 08/12] net: ethernet: Add helper for MACs which support asym pause Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:39 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 10/12] net: ethernet: Add helper for set_pauseparam for Asym Pause Andrew Lunn
` (3 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/broadcom/bcm63xx_enet.c | 2 +-
drivers/net/ethernet/freescale/fec_main.c | 4 +---
drivers/net/phy/phy_device.c | 14 ++++++++++++++
include/linux/phy.h | 1 +
4 files changed, 17 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bcm63xx_enet.c b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
index 2eee9459c2cf..c55b49b82690 100644
--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
@@ -890,7 +890,7 @@ static int bcm_enet_open(struct net_device *dev)
}
/* mask with MAC supported features */
- phydev->supported |= SUPPORTED_Pause;
+ phy_support_pause(phydev);
phy_set_max_speed(phydev, SPEED_100);
if (priv->pause_auto && priv->pause_rx && priv->pause_tx)
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index 0c6fd77b6599..043b8c76821e 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -1950,14 +1950,12 @@ static int fec_enet_mii_probe(struct net_device *ndev)
phy_remove_link_mode(phy_dev,
ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
#if !defined(CONFIG_M5272)
- phy_dev->supported |= SUPPORTED_Pause;
+ phy_support_pause(phy_dev);
#endif
}
else
phy_set_max_speed(phy_dev, 100);
- phy_dev->advertising = phy_dev->supported;
-
fep->link = 0;
fep->full_duplex = 0;
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index a0646a66f005..5273091450a8 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1783,6 +1783,20 @@ void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode)
}
EXPORT_SYMBOL(phy_remove_link_mode);
+/**
+ * phy_support_pause - Enable support of pause
+ * @phydev: target phy_device struct
+ *
+ * Description: Called by the MAC to indicate is supports Pause, but not
+ * asym pause.
+ */
+void phy_support_pause(struct phy_device *phydev)
+{
+ phydev->supported |= SUPPORTED_Pause;
+ phydev->advertising = phydev->supported;
+}
+EXPORT_SYMBOL(phy_support_pause);
+
/**
* phy_support_asym_pause - Enable support of asym pause
* @phydev: target phy_device struct
diff --git a/include/linux/phy.h b/include/linux/phy.h
index e2db819807c1..083d51ff6b5a 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1050,6 +1050,7 @@ int phy_start_interrupts(struct phy_device *phydev);
void phy_print_status(struct phy_device *phydev);
int phy_set_max_speed(struct phy_device *phydev, u32 max_speed);
void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode);
+void phy_support_pause(struct phy_device *phydev);
void phy_support_asym_pause(struct phy_device *phydev);
int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask,
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [PATCH net-next 09/12] net: ethernet: Add helper for MACs which support pause
2018-09-02 17:06 ` [PATCH net-next 09/12] net: ethernet: Add helper for MACs which support pause Andrew Lunn
@ 2018-09-03 17:39 ` Florian Fainelli
2018-09-03 19:54 ` Andrew Lunn
0 siblings, 1 reply; 30+ messages in thread
From: Florian Fainelli @ 2018-09-03 17:39 UTC (permalink / raw)
To: Andrew Lunn, David Miller; +Cc: netdev, maxime.chevallier
On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> Rather than have the MAC drivers manipulate phydev members, add a
> helper function for MACs supporting Pause, but not Asym Pause.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
I wonder if this would be better named phy_support_sym_pause() as
opposed to asym_pause()?
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH net-next 09/12] net: ethernet: Add helper for MACs which support pause
2018-09-03 17:39 ` Florian Fainelli
@ 2018-09-03 19:54 ` Andrew Lunn
0 siblings, 0 replies; 30+ messages in thread
From: Andrew Lunn @ 2018-09-03 19:54 UTC (permalink / raw)
To: Florian Fainelli; +Cc: David Miller, netdev, maxime.chevallier
On Mon, Sep 03, 2018 at 10:39:04AM -0700, Florian Fainelli wrote:
>
>
> On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> >Rather than have the MAC drivers manipulate phydev members, add a
> >helper function for MACs supporting Pause, but not Asym Pause.
> >
> >Signed-off-by: Andrew Lunn <andrew@lunn.ch>
>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
>
> I wonder if this would be better named phy_support_sym_pause() as opposed to
> asym_pause()?
Hi Florian
Maybe, bit it is then very similar to asym. I wounder if there is some
other word we can use for the symmetrical case?
Andrew
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH net-next 10/12] net: ethernet: Add helper for set_pauseparam for Asym Pause
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (8 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 09/12] net: ethernet: Add helper for MACs which support pause Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:49 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 11/12] net: ethernet: Add helper for set_pauseparam for Pause Andrew Lunn
` (2 subsequent siblings)
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
.../ethernet/apm/xgene/xgene_enet_ethtool.c | 26 ++-------
drivers/net/ethernet/aurora/nb8800.c | 9 +---
drivers/net/ethernet/broadcom/tg3.c | 43 +++++----------
drivers/net/ethernet/faraday/ftgmac100.c | 13 +----
.../ethernet/freescale/dpaa/dpaa_ethtool.c | 26 ++-------
.../net/ethernet/freescale/gianfar_ethtool.c | 53 +++++++------------
.../hisilicon/hns3/hns3pf/hclge_main.c | 8 +--
drivers/net/ethernet/socionext/sni_ave.c | 6 +--
drivers/net/phy/phy_device.c | 23 ++++++++
include/linux/phy.h | 1 +
10 files changed, 69 insertions(+), 139 deletions(-)
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c b/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c
index 4f50f11718f4..dfe03afd00b0 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c
@@ -306,7 +306,6 @@ static int xgene_set_pauseparam(struct net_device *ndev,
{
struct xgene_enet_pdata *pdata = netdev_priv(ndev);
struct phy_device *phydev = ndev->phydev;
- u32 oldadv, newadv;
if (phy_interface_mode_is_rgmii(pdata->phy_mode) ||
pdata->phy_mode == PHY_INTERFACE_MODE_SGMII) {
@@ -322,29 +321,12 @@ static int xgene_set_pauseparam(struct net_device *ndev,
pdata->tx_pause = pp->tx_pause;
pdata->rx_pause = pp->rx_pause;
- oldadv = phydev->advertising;
- newadv = oldadv & ~(ADVERTISED_Pause | ADVERTISED_Asym_Pause);
+ phy_set_asym_pause(phydev, pp->rx_pause, pp->tx_pause);
- if (pp->rx_pause)
- newadv |= ADVERTISED_Pause | ADVERTISED_Asym_Pause;
-
- if (pp->tx_pause)
- newadv ^= ADVERTISED_Asym_Pause;
-
- if (oldadv ^ newadv) {
- phydev->advertising = newadv;
-
- if (phydev->autoneg)
- return phy_start_aneg(phydev);
-
- if (!pp->autoneg) {
- pdata->mac_ops->flowctl_tx(pdata,
- pdata->tx_pause);
- pdata->mac_ops->flowctl_rx(pdata,
- pdata->rx_pause);
- }
+ if (!pp->autoneg) {
+ pdata->mac_ops->flowctl_tx(pdata, pdata->tx_pause);
+ pdata->mac_ops->flowctl_rx(pdata, pdata->rx_pause);
}
-
} else {
if (pp->autoneg)
return -EINVAL;
diff --git a/drivers/net/ethernet/aurora/nb8800.c b/drivers/net/ethernet/aurora/nb8800.c
index c8d1f8fa4713..6f56276015a4 100644
--- a/drivers/net/ethernet/aurora/nb8800.c
+++ b/drivers/net/ethernet/aurora/nb8800.c
@@ -935,18 +935,11 @@ static void nb8800_pause_adv(struct net_device *dev)
{
struct nb8800_priv *priv = netdev_priv(dev);
struct phy_device *phydev = dev->phydev;
- u32 adv = 0;
if (!phydev)
return;
- if (priv->pause_rx)
- adv |= ADVERTISED_Pause | ADVERTISED_Asym_Pause;
- if (priv->pause_tx)
- adv ^= ADVERTISED_Asym_Pause;
-
- phydev->supported |= adv;
- phydev->advertising |= adv;
+ phy_set_asym_pause(phydev, priv->pause_rx, priv->pause_tx);
}
static int nb8800_open(struct net_device *dev)
diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index 9aa7955d5d31..b406b6e34a8c 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -12492,7 +12492,6 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
tg3_warn_mgmt_link_flap(tp);
if (tg3_flag(tp, USE_PHYLIB)) {
- u32 newadv;
struct phy_device *phydev;
phydev = mdiobus_get_phy(tp->mdio_bus, tp->phy_addr);
@@ -12503,20 +12502,16 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
return -EINVAL;
tp->link_config.flowctrl = 0;
+ phy_set_asym_pause(phydev, epause->rx_pause, epause->tx_pause);
if (epause->rx_pause) {
tp->link_config.flowctrl |= FLOW_CTRL_RX;
if (epause->tx_pause) {
tp->link_config.flowctrl |= FLOW_CTRL_TX;
- newadv = ADVERTISED_Pause;
- } else
- newadv = ADVERTISED_Pause |
- ADVERTISED_Asym_Pause;
+ }
} else if (epause->tx_pause) {
tp->link_config.flowctrl |= FLOW_CTRL_TX;
- newadv = ADVERTISED_Asym_Pause;
- } else
- newadv = 0;
+ }
if (epause->autoneg)
tg3_flag_set(tp, PAUSE_AUTONEG);
@@ -12524,33 +12519,19 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
tg3_flag_clear(tp, PAUSE_AUTONEG);
if (tp->phy_flags & TG3_PHYFLG_IS_CONNECTED) {
- u32 oldadv = phydev->advertising &
- (ADVERTISED_Pause | ADVERTISED_Asym_Pause);
- if (oldadv != newadv) {
- phydev->advertising &=
- ~(ADVERTISED_Pause |
- ADVERTISED_Asym_Pause);
- phydev->advertising |= newadv;
- if (phydev->autoneg) {
- /*
- * Always renegotiate the link to
- * inform our link partner of our
- * flow control settings, even if the
- * flow control is forced. Let
- * tg3_adjust_link() do the final
- * flow control setup.
- */
- return phy_start_aneg(phydev);
- }
+ if (phydev->autoneg) {
+ /* Always renegotiate the link to
+ * inform our link partner of our flow
+ * control settings, even if the flow
+ * control is forced. Let
+ * tg3_adjust_link() do the final flow
+ * control setup.
+ */
+ return phy_start_aneg(phydev);
}
if (!epause->autoneg)
tg3_setup_flow_control(tp, 0, 0);
- } else {
- tp->link_config.advertising &=
- ~(ADVERTISED_Pause |
- ADVERTISED_Asym_Pause);
- tp->link_config.advertising |= newadv;
}
} else {
int irq_sync = 0;
diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 3f319ee66ab4..032d59ffae8b 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -1219,18 +1219,9 @@ static int ftgmac100_set_pauseparam(struct net_device *netdev,
priv->tx_pause = pause->tx_pause;
priv->rx_pause = pause->rx_pause;
- if (phydev) {
- phydev->advertising &= ~ADVERTISED_Pause;
- phydev->advertising &= ~ADVERTISED_Asym_Pause;
+ if (phydev)
+ phy_set_asym_pause(phydev, pause->rx_pause, pause->tx_pause);
- if (pause->rx_pause) {
- phydev->advertising |= ADVERTISED_Pause;
- phydev->advertising |= ADVERTISED_Asym_Pause;
- }
-
- if (pause->tx_pause)
- phydev->advertising ^= ADVERTISED_Asym_Pause;
- }
if (netif_running(netdev)) {
if (phydev && priv->aneg_pause)
phy_start_aneg(phydev);
diff --git a/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c b/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c
index 3184c8f7cdd0..80a9f2758030 100644
--- a/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c
+++ b/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c
@@ -210,28 +210,12 @@ static int dpaa_set_pauseparam(struct net_device *net_dev,
/* Determine the sym/asym advertised PAUSE capabilities from the desired
* rx/tx pause settings.
*/
- newadv = 0;
- if (epause->rx_pause)
- newadv = ADVERTISED_Pause | ADVERTISED_Asym_Pause;
- if (epause->tx_pause)
- newadv ^= ADVERTISED_Asym_Pause;
- oldadv = phydev->advertising &
- (ADVERTISED_Pause | ADVERTISED_Asym_Pause);
-
- /* If there are differences between the old and the new advertised
- * values, restart PHY autonegotiation and advertise the new values.
- */
- if (oldadv != newadv) {
- phydev->advertising &= ~(ADVERTISED_Pause
- | ADVERTISED_Asym_Pause);
- phydev->advertising |= newadv;
- if (phydev->autoneg) {
- err = phy_start_aneg(phydev);
- if (err < 0)
- netdev_err(net_dev, "phy_start_aneg() = %d\n",
- err);
- }
+ phy_set_asym_pause(phydev, epause->rx_pause, epause->tx_pause);
+ if (phydev->autoneg) {
+ err = phy_start_aneg(phydev);
+ if (err < 0)
+ netdev_err(net_dev, "phy_start_aneg() = %d\n", err);
}
fman_get_pause_cfg(mac_dev, &rx_pause, &tx_pause);
diff --git a/drivers/net/ethernet/freescale/gianfar_ethtool.c b/drivers/net/ethernet/freescale/gianfar_ethtool.c
index 395a5266ea30..589a99718694 100644
--- a/drivers/net/ethernet/freescale/gianfar_ethtool.c
+++ b/drivers/net/ethernet/freescale/gianfar_ethtool.c
@@ -503,7 +503,6 @@ static int gfar_spauseparam(struct net_device *dev,
struct gfar_private *priv = netdev_priv(dev);
struct phy_device *phydev = dev->phydev;
struct gfar __iomem *regs = priv->gfargrp[0].regs;
- u32 oldadv, newadv;
if (!phydev)
return -ENODEV;
@@ -514,54 +513,40 @@ static int gfar_spauseparam(struct net_device *dev,
return -EINVAL;
priv->rx_pause_en = priv->tx_pause_en = 0;
+ phy_set_asym_pause(phydev, epause->rx_pause, epause->tx_pause);
if (epause->rx_pause) {
priv->rx_pause_en = 1;
if (epause->tx_pause) {
priv->tx_pause_en = 1;
- /* FLOW_CTRL_RX & TX */
- newadv = ADVERTISED_Pause;
- } else /* FLOW_CTLR_RX */
- newadv = ADVERTISED_Pause | ADVERTISED_Asym_Pause;
+ }
} else if (epause->tx_pause) {
priv->tx_pause_en = 1;
- /* FLOW_CTLR_TX */
- newadv = ADVERTISED_Asym_Pause;
- } else
- newadv = 0;
+ }
if (epause->autoneg)
priv->pause_aneg_en = 1;
else
priv->pause_aneg_en = 0;
- oldadv = phydev->advertising &
- (ADVERTISED_Pause | ADVERTISED_Asym_Pause);
- if (oldadv != newadv) {
- phydev->advertising &=
- ~(ADVERTISED_Pause | ADVERTISED_Asym_Pause);
- phydev->advertising |= newadv;
- if (phydev->autoneg)
- /* inform link partner of our
- * new flow ctrl settings
- */
- return phy_start_aneg(phydev);
-
- if (!epause->autoneg) {
- u32 tempval;
- tempval = gfar_read(®s->maccfg1);
- tempval &= ~(MACCFG1_TX_FLOW | MACCFG1_RX_FLOW);
-
- priv->tx_actual_en = 0;
- if (priv->tx_pause_en) {
- priv->tx_actual_en = 1;
- tempval |= MACCFG1_TX_FLOW;
- }
+ if (phydev->autoneg)
+ /* inform link partner of our new flow ctrl settings */
+ return phy_start_aneg(phydev);
- if (priv->rx_pause_en)
- tempval |= MACCFG1_RX_FLOW;
- gfar_write(®s->maccfg1, tempval);
+ if (!epause->autoneg) {
+ u32 tempval = gfar_read(®s->maccfg1);
+
+ tempval &= ~(MACCFG1_TX_FLOW | MACCFG1_RX_FLOW);
+
+ priv->tx_actual_en = 0;
+ if (priv->tx_pause_en) {
+ priv->tx_actual_en = 1;
+ tempval |= MACCFG1_TX_FLOW;
}
+
+ if (priv->rx_pause_en)
+ tempval |= MACCFG1_RX_FLOW;
+ gfar_write(®s->maccfg1, tempval);
}
return 0;
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
index 8577dfc799ad..aa7babff2fc2 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
@@ -5208,13 +5208,7 @@ static void hclge_set_flowctrl_adv(struct hclge_dev *hdev, u32 rx_en, u32 tx_en)
if (!phydev)
return;
- phydev->advertising &= ~(ADVERTISED_Pause | ADVERTISED_Asym_Pause);
-
- if (rx_en)
- phydev->advertising |= ADVERTISED_Pause | ADVERTISED_Asym_Pause;
-
- if (tx_en)
- phydev->advertising ^= ADVERTISED_Asym_Pause;
+ phy_set_asym_pause(phydev, rx_en, tx_en);
}
static int hclge_cfg_pauseparam(struct hclge_dev *hdev, u32 rx_en, u32 tx_en)
diff --git a/drivers/net/ethernet/socionext/sni_ave.c b/drivers/net/ethernet/socionext/sni_ave.c
index a50720ec109c..fedda3fa585d 100644
--- a/drivers/net/ethernet/socionext/sni_ave.c
+++ b/drivers/net/ethernet/socionext/sni_ave.c
@@ -461,11 +461,7 @@ static int ave_ethtool_set_pauseparam(struct net_device *ndev,
priv->pause_rx = pause->rx_pause;
priv->pause_tx = pause->tx_pause;
- phydev->advertising &= ~(ADVERTISED_Pause | ADVERTISED_Asym_Pause);
- if (pause->rx_pause)
- phydev->advertising |= ADVERTISED_Pause | ADVERTISED_Asym_Pause;
- if (pause->tx_pause)
- phydev->advertising ^= ADVERTISED_Asym_Pause;
+ phy_set_asym_pause(phydev, pause->rx_pause, pause->tx_pause);
if (pause->autoneg) {
if (netif_running(ndev))
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 5273091450a8..bcdcd4a42d82 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1810,6 +1810,29 @@ void phy_support_asym_pause(struct phy_device *phydev)
}
EXPORT_SYMBOL(phy_support_asym_pause);
+/**
+ * phy_set_asym_pause - Configure Pause and Asym Pause
+ * @phydev: target phy_device struct
+ * @rx: Receiver Pause is supported
+ * @tx: Transmit Pause is supported
+ *
+ * Description: Configure advertised Pause support depending on if
+ * transmit and receiver pause is supported. Generally called from the
+ * set_pauseparam .ndo.
+ */
+void phy_set_asym_pause(struct phy_device *phydev, bool rx, bool tx)
+{
+ phydev->supported &= ~(SUPPORTED_Pause | SUPPORTED_Asym_Pause);
+
+ if (rx)
+ phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
+ if (tx)
+ phydev->supported ^= SUPPORTED_Asym_Pause;
+
+ phydev->advertising = phydev->supported;
+}
+EXPORT_SYMBOL(phy_set_asym_pause);
+
static void of_set_phy_supported(struct phy_device *phydev)
{
struct device_node *node = phydev->mdio.dev.of_node;
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 083d51ff6b5a..f767a8f22856 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1052,6 +1052,7 @@ int phy_set_max_speed(struct phy_device *phydev, u32 max_speed);
void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode);
void phy_support_pause(struct phy_device *phydev);
void phy_support_asym_pause(struct phy_device *phydev);
+void phy_set_asym_pause(struct phy_device *phydev, bool rx, bool tx);
int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask,
int (*run)(struct phy_device *));
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [PATCH net-next 10/12] net: ethernet: Add helper for set_pauseparam for Asym Pause
2018-09-02 17:06 ` [PATCH net-next 10/12] net: ethernet: Add helper for set_pauseparam for Asym Pause Andrew Lunn
@ 2018-09-03 17:49 ` Florian Fainelli
2018-09-03 19:58 ` Andrew Lunn
0 siblings, 1 reply; 30+ messages in thread
From: Florian Fainelli @ 2018-09-03 17:49 UTC (permalink / raw)
To: Andrew Lunn, David Miller; +Cc: netdev, maxime.chevallier
On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> ethtool can be used to enable/disable pause. Add a helper to configure
> the PHY when asym pause is supported.
Don't you want to go one step further and incorporate the logic that
xgenet, tg3, gianfar and others have? That is: look at the currently
advertised parameters, determine what changed, and re-start
auto-negotiation as a result of it being enabled and something changed?
Could be done as a follow-up patch I suppose, although see below:
[snip]
> index 4f50f11718f4..dfe03afd00b0 100644
> --- a/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c
> +++ b/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c
> @@ -306,7 +306,6 @@ static int xgene_set_pauseparam(struct net_device *ndev,
> {
> struct xgene_enet_pdata *pdata = netdev_priv(ndev);
> struct phy_device *phydev = ndev->phydev;
> - u32 oldadv, newadv;
>
> if (phy_interface_mode_is_rgmii(pdata->phy_mode) ||
> pdata->phy_mode == PHY_INTERFACE_MODE_SGMII) {
> @@ -322,29 +321,12 @@ static int xgene_set_pauseparam(struct net_device *ndev,
> pdata->tx_pause = pp->tx_pause;
> pdata->rx_pause = pp->rx_pause;
>
> - oldadv = phydev->advertising;
> - newadv = oldadv & ~(ADVERTISED_Pause | ADVERTISED_Asym_Pause);
> + phy_set_asym_pause(phydev, pp->rx_pause, pp->tx_pause);
>
> - if (pp->rx_pause)
> - newadv |= ADVERTISED_Pause | ADVERTISED_Asym_Pause;
> -
> - if (pp->tx_pause)
> - newadv ^= ADVERTISED_Asym_Pause;
> -
> - if (oldadv ^ newadv) {
> - phydev->advertising = newadv;
> -
> - if (phydev->autoneg)
> - return phy_start_aneg(phydev);
> -
You have remove the part that checks for phydev->autoneg here, was that
intentional?
> - if (!pp->autoneg) {
> - pdata->mac_ops->flowctl_tx(pdata,
> - pdata->tx_pause);
> - pdata->mac_ops->flowctl_rx(pdata,
> - pdata->rx_pause);
> - }
> + if (!pp->autoneg) {
> + pdata->mac_ops->flowctl_tx(pdata, pdata->tx_pause);
> + pdata->mac_ops->flowctl_rx(pdata, pdata->rx_pause);
> }
--
Florian
^ permalink raw reply [flat|nested] 30+ messages in thread* Re: [PATCH net-next 10/12] net: ethernet: Add helper for set_pauseparam for Asym Pause
2018-09-03 17:49 ` Florian Fainelli
@ 2018-09-03 19:58 ` Andrew Lunn
2018-09-03 22:30 ` Florian Fainelli
0 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-03 19:58 UTC (permalink / raw)
To: Florian Fainelli; +Cc: David Miller, netdev, maxime.chevallier
> Don't you want to go one step further and incorporate the logic that xgenet,
> tg3, gianfar and others have? That is: look at the currently advertised
> parameters, determine what changed, and re-start auto-negotiation as a
> result of it being enabled and something changed?
Hi Florian
Given the number of changes i'm making, over a so many different
drivers which i cannot test, i wanted to try to keep the changes
KISS. That way we are more likely to spot errors during review. So i
would prefer to be done later, unless it actually makes review
simpler...
Andrew
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH net-next 10/12] net: ethernet: Add helper for set_pauseparam for Asym Pause
2018-09-03 19:58 ` Andrew Lunn
@ 2018-09-03 22:30 ` Florian Fainelli
0 siblings, 0 replies; 30+ messages in thread
From: Florian Fainelli @ 2018-09-03 22:30 UTC (permalink / raw)
To: Andrew Lunn; +Cc: David Miller, netdev, maxime.chevallier
On 09/03/18 12:58, Andrew Lunn wrote:
>> Don't you want to go one step further and incorporate the logic that xgenet,
>> tg3, gianfar and others have? That is: look at the currently advertised
>> parameters, determine what changed, and re-start auto-negotiation as a
>> result of it being enabled and something changed?
>
> Hi Florian
>
> Given the number of changes i'm making, over a so many different
> drivers which i cannot test, i wanted to try to keep the changes
> KISS. That way we are more likely to spot errors during review. So i
> would prefer to be done later, unless it actually makes review
> simpler...
That's fine, but you still need to keep the test for phydev->autoneg in
xgene I believe. Since all of these drivers appear to be doing the same
thing, that's why I suggested moving this into the helper directly.
--
Florian
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH net-next 11/12] net: ethernet: Add helper for set_pauseparam for Pause
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (9 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 10/12] net: ethernet: Add helper for set_pauseparam for Asym Pause Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:49 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 12/12] net: ethernet: Add helper to determine if pause configuration is supported Andrew Lunn
2018-09-04 2:44 ` [PATCH net-next 00/12] Preparing for phylib limkmodes David Miller
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/broadcom/bcm63xx_enet.c | 6 +-----
drivers/net/ethernet/freescale/fec_main.c | 8 +-------
drivers/net/phy/phy_device.c | 21 ++++++++++++++++++++
include/linux/phy.h | 1 +
4 files changed, 24 insertions(+), 12 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bcm63xx_enet.c b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
index c55b49b82690..e297972c63cf 100644
--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
@@ -892,11 +892,7 @@ static int bcm_enet_open(struct net_device *dev)
/* mask with MAC supported features */
phy_support_pause(phydev);
phy_set_max_speed(phydev, SPEED_100);
-
- if (priv->pause_auto && priv->pause_rx && priv->pause_tx)
- phydev->advertising |= SUPPORTED_Pause;
- else
- phydev->advertising &= ~SUPPORTED_Pause;
+ phy_set_pause(phydev, priv->pause_rx, priv->pause_auto);
phy_attached_info(phydev);
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index 043b8c76821e..239eeac3d7ce 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -2229,13 +2229,7 @@ static int fec_enet_set_pauseparam(struct net_device *ndev,
fep->pause_flag |= pause->rx_pause ? FEC_PAUSE_FLAG_ENABLE : 0;
fep->pause_flag |= pause->autoneg ? FEC_PAUSE_FLAG_AUTONEG : 0;
- if (pause->rx_pause || pause->autoneg) {
- ndev->phydev->supported |= ADVERTISED_Pause;
- ndev->phydev->advertising |= ADVERTISED_Pause;
- } else {
- ndev->phydev->supported &= ~ADVERTISED_Pause;
- ndev->phydev->advertising &= ~ADVERTISED_Pause;
- }
+ phy_set_pause(ndev->phydev, pause->rx_pause, pause->autoneg);
if (pause->autoneg) {
if (netif_running(ndev))
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index bcdcd4a42d82..3078792b900f 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1810,6 +1810,27 @@ void phy_support_asym_pause(struct phy_device *phydev)
}
EXPORT_SYMBOL(phy_support_asym_pause);
+/**
+ * phy_set_pause - Configure Pause
+ * @phydev: target phy_device struct
+ * @rx: Receiver Pause is supported
+ * @autoneg: Auto neg should be used
+ *
+ * Description: Configure advertised Pause support depending on if
+ * receiver pause and pause auto neg is supported. Generally called
+ * from the set_pauseparam .ndo.
+ */
+void phy_set_pause(struct phy_device *phydev, bool rx, bool autoneg)
+{
+ phydev->supported &= ~SUPPORTED_Pause;
+
+ if (rx || autoneg)
+ phydev->supported |= SUPPORTED_Pause;
+
+ phydev->advertising = phydev->supported;
+}
+EXPORT_SYMBOL(phy_set_pause);
+
/**
* phy_set_asym_pause - Configure Pause and Asym Pause
* @phydev: target phy_device struct
diff --git a/include/linux/phy.h b/include/linux/phy.h
index f767a8f22856..205fb966d686 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1052,6 +1052,7 @@ int phy_set_max_speed(struct phy_device *phydev, u32 max_speed);
void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode);
void phy_support_pause(struct phy_device *phydev);
void phy_support_asym_pause(struct phy_device *phydev);
+void phy_set_pause(struct phy_device *phydev, bool rx, bool autoneg);
void phy_set_asym_pause(struct phy_device *phydev, bool rx, bool tx);
int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask,
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [PATCH net-next 11/12] net: ethernet: Add helper for set_pauseparam for Pause
2018-09-02 17:06 ` [PATCH net-next 11/12] net: ethernet: Add helper for set_pauseparam for Pause Andrew Lunn
@ 2018-09-03 17:49 ` Florian Fainelli
0 siblings, 0 replies; 30+ messages in thread
From: Florian Fainelli @ 2018-09-03 17:49 UTC (permalink / raw)
To: Andrew Lunn, David Miller; +Cc: netdev, maxime.chevallier
On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> ethtool can be used to enable/disable pause. Add a helper to configure
> the PHY when Pause is supported.
One comment, see below:
[snip]
> +/**
> + * phy_set_pause - Configure Pause
> + * @phydev: target phy_device struct
> + * @rx: Receiver Pause is supported
> + * @autoneg: Auto neg should be used
> + *
> + * Description: Configure advertised Pause support depending on if
> + * receiver pause and pause auto neg is supported. Generally called
> + * from the set_pauseparam .ndo.
> + */
> +void phy_set_pause(struct phy_device *phydev, bool rx, bool autoneg)
> +{
> + phydev->supported &= ~SUPPORTED_Pause;
> +
> + if (rx || autoneg)
> + phydev->supported |= SUPPORTED_Pause;
> +
> + phydev->advertising = phydev->supported;
This is the logic from FEC, but I think the one from bcm63xx_enet.c is
actually the correct one, you can enable symmetric pause support if it
is enabled for both the RX and TX paths here.
Similar comment to patch 9, I would name this phy_set_sym_pause() for
clarity.
--
Florian
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH net-next 12/12] net: ethernet: Add helper to determine if pause configuration is supported
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (10 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 11/12] net: ethernet: Add helper for set_pauseparam for Pause Andrew Lunn
@ 2018-09-02 17:06 ` Andrew Lunn
2018-09-03 17:52 ` Florian Fainelli
2018-09-04 2:44 ` [PATCH net-next 00/12] Preparing for phylib limkmodes David Miller
12 siblings, 1 reply; 30+ messages in thread
From: Andrew Lunn @ 2018-09-02 17:06 UTC (permalink / raw)
To: David Miller; +Cc: netdev, Florian Fainelli, maxime.chevallier, Andrew Lunn
Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
.../ethernet/apm/xgene/xgene_enet_ethtool.c | 4 +---
drivers/net/ethernet/broadcom/tg3.c | 4 +---
.../ethernet/freescale/dpaa/dpaa_ethtool.c | 4 +---
.../net/ethernet/freescale/gianfar_ethtool.c | 4 +---
drivers/net/phy/phy_device.c | 20 +++++++++++++++++++
include/linux/phy.h | 2 ++
6 files changed, 26 insertions(+), 12 deletions(-)
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c b/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c
index dfe03afd00b0..78dd09b5beeb 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_ethtool.c
@@ -312,9 +312,7 @@ static int xgene_set_pauseparam(struct net_device *ndev,
if (!phydev)
return -EINVAL;
- if (!(phydev->supported & SUPPORTED_Pause) ||
- (!(phydev->supported & SUPPORTED_Asym_Pause) &&
- pp->rx_pause != pp->tx_pause))
+ if (!phy_validate_pause(phydev, pp))
return -EINVAL;
pdata->pause_autoneg = pp->autoneg;
diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index b406b6e34a8c..c6b5a9932d79 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -12496,9 +12496,7 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
phydev = mdiobus_get_phy(tp->mdio_bus, tp->phy_addr);
- if (!(phydev->supported & SUPPORTED_Pause) ||
- (!(phydev->supported & SUPPORTED_Asym_Pause) &&
- (epause->rx_pause != epause->tx_pause)))
+ if (!phy_validate_pause(phydev, epause))
return -EINVAL;
tp->link_config.flowctrl = 0;
diff --git a/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c b/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c
index 80a9f2758030..0f0ebdb791cf 100644
--- a/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c
+++ b/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c
@@ -194,9 +194,7 @@ static int dpaa_set_pauseparam(struct net_device *net_dev,
return -ENODEV;
}
- if (!(phydev->supported & SUPPORTED_Pause) ||
- (!(phydev->supported & SUPPORTED_Asym_Pause) &&
- (epause->rx_pause != epause->tx_pause)))
+ if (!phy_validate_pause(phydev, epause))
return -EINVAL;
/* The MAC should know how to handle PAUSE frame autonegotiation before
diff --git a/drivers/net/ethernet/freescale/gianfar_ethtool.c b/drivers/net/ethernet/freescale/gianfar_ethtool.c
index 589a99718694..f8e08ee0be19 100644
--- a/drivers/net/ethernet/freescale/gianfar_ethtool.c
+++ b/drivers/net/ethernet/freescale/gianfar_ethtool.c
@@ -507,9 +507,7 @@ static int gfar_spauseparam(struct net_device *dev,
if (!phydev)
return -ENODEV;
- if (!(phydev->supported & SUPPORTED_Pause) ||
- (!(phydev->supported & SUPPORTED_Asym_Pause) &&
- (epause->rx_pause != epause->tx_pause)))
+ if (!phy_validate_pause(phydev, epause))
return -EINVAL;
priv->rx_pause_en = priv->tx_pause_en = 0;
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 3078792b900f..c1fdb01d56d2 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1854,6 +1854,26 @@ void phy_set_asym_pause(struct phy_device *phydev, bool rx, bool tx)
}
EXPORT_SYMBOL(phy_set_asym_pause);
+/**
+ * phy_validate_pause - Test if the PHY/MAC support the pause configuration
+ * @phydev: phy_device struct
+ * @pp: requested pause configuration
+ *
+ * Description: Test if the PHY/MAC combination supports the Pause
+ * configuration the user is requesting. Returns True if it is
+ * supported, false otherwise.
+ */
+bool phy_validate_pause(struct phy_device *phydev,
+ struct ethtool_pauseparam *pp)
+{
+ if (!(phydev->supported & SUPPORTED_Pause) ||
+ (!(phydev->supported & SUPPORTED_Asym_Pause) &&
+ pp->rx_pause != pp->tx_pause))
+ return false;
+ return true;
+}
+EXPORT_SYMBOL(phy_validate_pause);
+
static void of_set_phy_supported(struct phy_device *phydev)
{
struct device_node *node = phydev->mdio.dev.of_node;
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 205fb966d686..a8df64841e31 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1054,6 +1054,8 @@ void phy_support_pause(struct phy_device *phydev);
void phy_support_asym_pause(struct phy_device *phydev);
void phy_set_pause(struct phy_device *phydev, bool rx, bool autoneg);
void phy_set_asym_pause(struct phy_device *phydev, bool rx, bool tx);
+bool phy_validate_pause(struct phy_device *phydev,
+ struct ethtool_pauseparam *pp);
int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask,
int (*run)(struct phy_device *));
--
2.19.0.rc1
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [PATCH net-next 00/12] Preparing for phylib limkmodes
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
` (11 preceding siblings ...)
2018-09-02 17:06 ` [PATCH net-next 12/12] net: ethernet: Add helper to determine if pause configuration is supported Andrew Lunn
@ 2018-09-04 2:44 ` David Miller
12 siblings, 0 replies; 30+ messages in thread
From: David Miller @ 2018-09-04 2:44 UTC (permalink / raw)
To: andrew; +Cc: netdev, f.fainelli, maxime.chevallier
From: Andrew Lunn <andrew@lunn.ch>
Date: Sun, 2 Sep 2018 19:06:29 +0200
> phylib currently makes us of a u32 bitmap for advertising, supported,
> and link partner capabilities. For a long time, this has been
> sufficient, for devices up to 1Gbps. With more MAC/PHY combinations
> now supporting speeds greater than 1Gbps, we have run out of
> bits. There is the need to replace this u32 with an
> __ETHTOOL_DECLARE_LINK_MODE_MASK, which makes use of linux's generic
> bitmaps.
>
> This patchset does some of the work preparing for this change. A few
> cleanups are applied to PHY drivers. Some MAC drivers directly access
> members of phydev which are going to change type. These patches adds
> some helpers and swaps MAC drivers to use them, mostly dealing with
> Pause configuration.
Andrew, please fix the indentation issue Florian pointed out in patch
#8 and finish the other feedback threads which seem to still be in
progress.
Thanks!
^ permalink raw reply [flat|nested] 30+ messages in thread