* [PATCH v2 0/4] Add basic Rockchip rk3128 DT support
@ 2022-10-28 14:39 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:39 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add basic Rockchip rk3128 DT support.
Features:
Quad-core ARM Cortex-A7MP Core processor
Clock & reset unit
Power management unit
Interrupt controller
DMAC
6x 64 bits Timers
4x PWMs
1x 32 bits watchdog
Internal memory:
Internal BootRom
Internal SRAM 8KB
External memory:
Dynamic Memory Interface (DDR3/DDR3L/LPDDR2)
Nand Flash Interface
eMMC Interface
SD/MMC Interface
Connectivity:
SDIO interface
SPI Controller
3x UART controller
4x I2C controllers
4x groups of GPIO (GPIO0~GPIO3), 32 GPIOs per group
USB Host2.0
USB OTG2.0
===
The Linux kernel has added a rk3128 clock driver in the past,
but the DT is still missing.
In U-boot the rk3128 DT doesn't conform the latest bindings
and also the pin definition don't match the TRM.
On request from the U-boot maintainers I submit a basic rk3128 DT.
https://lore.kernel.org/u-boot/258c2dbf-436d-5935-83f5-a2dbb8cf62d7@rock-chips.com/
Based on:
https://source.denx.de/u-boot/u-boot/-/blob/master/arch/arm/dts/rk3128.dtsi
https://github.com/rockchip-linux/kernel/blob/develop-4.4/arch/arm/boot/dts/rk312x.dtsi
rk3128 TRM:
https://rockchip.fr/RK312X%20TRM/
rk3128 datasheet:
https://rockchip.fr/RK3128%20datasheet%20V1.2.pdf
===
NOT TESTED WITH HARDWARE
NO THERMAL PROTECTION
===
Request:
Help with testing on hardware.
===
Changed V2:
rk3128.dtsi:
remove aliases
add gic interrupts mask defines
add virtual timer interrupts
rk3128-evb.dts:
use generic node names
remove underscores in node names
add more aliases
sort
===
Johan Jonker (4):
dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
dt-bindings: timer: rockchip: add rockchip,rk3128-timer
ARM: dts: rockchip: add rk3128.dtsi
ARM: dts: rockchip: add rk3128-evb.dts
.../devicetree/bindings/arm/rockchip.yaml | 5 +
.../bindings/timer/rockchip,rk-timer.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3128-evb.dts | 110 +++
arch/arm/boot/dts/rk3128.dtsi | 916 ++++++++++++++++++
5 files changed, 1033 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3128-evb.dts
create mode 100644 arch/arm/boot/dts/rk3128.dtsi
--
2.20.1
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 0/4] Add basic Rockchip rk3128 DT support
@ 2022-10-28 14:39 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:39 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add basic Rockchip rk3128 DT support.
Features:
Quad-core ARM Cortex-A7MP Core processor
Clock & reset unit
Power management unit
Interrupt controller
DMAC
6x 64 bits Timers
4x PWMs
1x 32 bits watchdog
Internal memory:
Internal BootRom
Internal SRAM 8KB
External memory:
Dynamic Memory Interface (DDR3/DDR3L/LPDDR2)
Nand Flash Interface
eMMC Interface
SD/MMC Interface
Connectivity:
SDIO interface
SPI Controller
3x UART controller
4x I2C controllers
4x groups of GPIO (GPIO0~GPIO3), 32 GPIOs per group
USB Host2.0
USB OTG2.0
===
The Linux kernel has added a rk3128 clock driver in the past,
but the DT is still missing.
In U-boot the rk3128 DT doesn't conform the latest bindings
and also the pin definition don't match the TRM.
On request from the U-boot maintainers I submit a basic rk3128 DT.
https://lore.kernel.org/u-boot/258c2dbf-436d-5935-83f5-a2dbb8cf62d7@rock-chips.com/
Based on:
https://source.denx.de/u-boot/u-boot/-/blob/master/arch/arm/dts/rk3128.dtsi
https://github.com/rockchip-linux/kernel/blob/develop-4.4/arch/arm/boot/dts/rk312x.dtsi
rk3128 TRM:
https://rockchip.fr/RK312X%20TRM/
rk3128 datasheet:
https://rockchip.fr/RK3128%20datasheet%20V1.2.pdf
===
NOT TESTED WITH HARDWARE
NO THERMAL PROTECTION
===
Request:
Help with testing on hardware.
===
Changed V2:
rk3128.dtsi:
remove aliases
add gic interrupts mask defines
add virtual timer interrupts
rk3128-evb.dts:
use generic node names
remove underscores in node names
add more aliases
sort
===
Johan Jonker (4):
dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
dt-bindings: timer: rockchip: add rockchip,rk3128-timer
ARM: dts: rockchip: add rk3128.dtsi
ARM: dts: rockchip: add rk3128-evb.dts
.../devicetree/bindings/arm/rockchip.yaml | 5 +
.../bindings/timer/rockchip,rk-timer.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3128-evb.dts | 110 +++
arch/arm/boot/dts/rk3128.dtsi | 916 ++++++++++++++++++
5 files changed, 1033 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3128-evb.dts
create mode 100644 arch/arm/boot/dts/rk3128.dtsi
--
2.20.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 0/4] Add basic Rockchip rk3128 DT support
@ 2022-10-28 14:39 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:39 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add basic Rockchip rk3128 DT support.
Features:
Quad-core ARM Cortex-A7MP Core processor
Clock & reset unit
Power management unit
Interrupt controller
DMAC
6x 64 bits Timers
4x PWMs
1x 32 bits watchdog
Internal memory:
Internal BootRom
Internal SRAM 8KB
External memory:
Dynamic Memory Interface (DDR3/DDR3L/LPDDR2)
Nand Flash Interface
eMMC Interface
SD/MMC Interface
Connectivity:
SDIO interface
SPI Controller
3x UART controller
4x I2C controllers
4x groups of GPIO (GPIO0~GPIO3), 32 GPIOs per group
USB Host2.0
USB OTG2.0
===
The Linux kernel has added a rk3128 clock driver in the past,
but the DT is still missing.
In U-boot the rk3128 DT doesn't conform the latest bindings
and also the pin definition don't match the TRM.
On request from the U-boot maintainers I submit a basic rk3128 DT.
https://lore.kernel.org/u-boot/258c2dbf-436d-5935-83f5-a2dbb8cf62d7@rock-chips.com/
Based on:
https://source.denx.de/u-boot/u-boot/-/blob/master/arch/arm/dts/rk3128.dtsi
https://github.com/rockchip-linux/kernel/blob/develop-4.4/arch/arm/boot/dts/rk312x.dtsi
rk3128 TRM:
https://rockchip.fr/RK312X%20TRM/
rk3128 datasheet:
https://rockchip.fr/RK3128%20datasheet%20V1.2.pdf
===
NOT TESTED WITH HARDWARE
NO THERMAL PROTECTION
===
Request:
Help with testing on hardware.
===
Changed V2:
rk3128.dtsi:
remove aliases
add gic interrupts mask defines
add virtual timer interrupts
rk3128-evb.dts:
use generic node names
remove underscores in node names
add more aliases
sort
===
Johan Jonker (4):
dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
dt-bindings: timer: rockchip: add rockchip,rk3128-timer
ARM: dts: rockchip: add rk3128.dtsi
ARM: dts: rockchip: add rk3128-evb.dts
.../devicetree/bindings/arm/rockchip.yaml | 5 +
.../bindings/timer/rockchip,rk-timer.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3128-evb.dts | 110 +++
arch/arm/boot/dts/rk3128.dtsi | 916 ++++++++++++++++++
5 files changed, 1033 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3128-evb.dts
create mode 100644 arch/arm/boot/dts/rk3128.dtsi
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 1/4] dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
2022-10-28 14:39 ` Johan Jonker
(?)
@ 2022-10-28 14:41 ` Johan Jonker
-1 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add Rockchip RK3128 Evaluation board.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 72bf2fbfe..e81d9d1ef 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -662,6 +662,11 @@ properties:
- const: rockchip,rk3036-evb
- const: rockchip,rk3036
+ - description: Rockchip RK3128 Evaluation board
+ items:
+ - const: rockchip,rk3128-evb
+ - const: rockchip,rk3128
+
- description: Rockchip RK3228 Evaluation board
items:
- const: rockchip,rk3228-evb
--
2.20.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 1/4] dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
@ 2022-10-28 14:41 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add Rockchip RK3128 Evaluation board.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 72bf2fbfe..e81d9d1ef 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -662,6 +662,11 @@ properties:
- const: rockchip,rk3036-evb
- const: rockchip,rk3036
+ - description: Rockchip RK3128 Evaluation board
+ items:
+ - const: rockchip,rk3128-evb
+ - const: rockchip,rk3128
+
- description: Rockchip RK3228 Evaluation board
items:
- const: rockchip,rk3228-evb
--
2.20.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 1/4] dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
@ 2022-10-28 14:41 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add Rockchip RK3128 Evaluation board.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 72bf2fbfe..e81d9d1ef 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -662,6 +662,11 @@ properties:
- const: rockchip,rk3036-evb
- const: rockchip,rk3036
+ - description: Rockchip RK3128 Evaluation board
+ items:
+ - const: rockchip,rk3128-evb
+ - const: rockchip,rk3128
+
- description: Rockchip RK3228 Evaluation board
items:
- const: rockchip,rk3228-evb
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 2/4] dt-bindings: timer: rockchip: add rockchip,rk3128-timer
2022-10-28 14:39 ` Johan Jonker
(?)
@ 2022-10-28 14:41 ` Johan Jonker
-1 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add rockchip,rk3128-timer compatible string.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---
Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
index dc3bc1e62..b61ed1a43 100644
--- a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
@@ -18,6 +18,7 @@ properties:
- enum:
- rockchip,rv1108-timer
- rockchip,rk3036-timer
+ - rockchip,rk3128-timer
- rockchip,rk3188-timer
- rockchip,rk3228-timer
- rockchip,rk3229-timer
--
2.20.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 2/4] dt-bindings: timer: rockchip: add rockchip,rk3128-timer
@ 2022-10-28 14:41 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add rockchip,rk3128-timer compatible string.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---
Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
index dc3bc1e62..b61ed1a43 100644
--- a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
@@ -18,6 +18,7 @@ properties:
- enum:
- rockchip,rv1108-timer
- rockchip,rk3036-timer
+ - rockchip,rk3128-timer
- rockchip,rk3188-timer
- rockchip,rk3228-timer
- rockchip,rk3229-timer
--
2.20.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 2/4] dt-bindings: timer: rockchip: add rockchip,rk3128-timer
@ 2022-10-28 14:41 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add rockchip,rk3128-timer compatible string.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---
Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
index dc3bc1e62..b61ed1a43 100644
--- a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
@@ -18,6 +18,7 @@ properties:
- enum:
- rockchip,rv1108-timer
- rockchip,rk3036-timer
+ - rockchip,rk3128-timer
- rockchip,rk3188-timer
- rockchip,rk3228-timer
- rockchip,rk3229-timer
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 3/4] ARM: dts: rockchip: add rk3128.dtsi
2022-10-28 14:39 ` Johan Jonker
(?)
@ 2022-10-28 14:41 ` Johan Jonker
-1 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add basic rk3128 support.
Features:
Quad-core ARM Cortex-A7MP Core processor
Clock & reset unit
Power management unit
Interrupt controller
DMAC
6x 64 bits Timers
4x PWMs
1x 32 bits watchdog
Internal memory:
Internal BootRom
Internal SRAM 8KB
External memory:
Dynamic Memory Interface (DDR3/DDR3L/LPDDR2)
Nand Flash Interface
eMMC Interface
SD/MMC Interface
Connectivity:
SDIO interface
SPI Controller
3x UART controller
4x I2C controllers
4x groups of GPIO (GPIO0~GPIO3), 32 GPIOs per group
USB Host2.0
USB OTG2.0
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
---
NOT TESTED WITH HARDWARE
NO THERMAL PROTECTION
---
Changed V2:
remove aliases
add gic interrupts mask defines
add virtual timer interrupts
---
arch/arm/boot/dts/rk3128.dtsi | 916 ++++++++++++++++++++++++++++++++++
1 file changed, 916 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3128.dtsi
diff --git a/arch/arm/boot/dts/rk3128.dtsi b/arch/arm/boot/dts/rk3128.dtsi
new file mode 100644
index 000000000..0480144c1
--- /dev/null
+++ b/arch/arm/boot/dts/rk3128.dtsi
@@ -0,0 +1,916 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2017 Rockchip Electronics Co., Ltd
+ */
+
+#include <dt-bindings/clock/rk3128-cru.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+
+/ {
+ compatible = "rockchip,rk3128";
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ arm-pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@f00 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf00>;
+ clock-latency = <40000>;
+ clocks = <&cru ARMCLK>;
+ operating-points = <
+ /* KHz uV */
+ 816000 1000000
+ >;
+ #cooling-cells = <2>; /* min followed by max */
+ };
+
+ cpu1: cpu@f01 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf01>;
+ };
+
+ cpu2: cpu@f02 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf02>;
+ };
+
+ cpu3: cpu@f03 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf03>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ arm,cpu-registers-not-fw-configured;
+ clock-frequency = <24000000>;
+ };
+
+ xin24m: oscillator {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xin24m";
+ #clock-cells = <0>;
+ };
+
+ pmu: syscon@100a0000 {
+ compatible = "rockchip,rk3128-pmu", "syscon", "simple-mfd";
+ reg = <0x100a0000 0x1000>;
+ };
+
+ gic: interrupt-controller@10139000 {
+ compatible = "arm,cortex-a7-gic";
+ reg = <0x10139000 0x1000>,
+ <0x1013a000 0x1000>,
+ <0x1013c000 0x2000>,
+ <0x1013e000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ };
+
+ usb_otg: usb@10180000 {
+ compatible = "rockchip,rk3128-usb", "rockchip,rk3066-usb", "snps,dwc2";
+ reg = <0x10180000 0x40000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_OTG>;
+ clock-names = "otg";
+ dr_mode = "otg";
+ phys = <&usb2phy_otg>;
+ phy-names = "usb2-phy";
+ status = "disabled";
+ };
+
+ usb_host_ehci: usb@101c0000 {
+ compatible = "generic-ehci";
+ reg = <0x101c0000 0x20000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2phy_host>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ usb_host_ohci: usb@101e0000 {
+ compatible = "generic-ohci";
+ reg = <0x101e0000 0x20000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2phy_host>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ sdmmc: mmc@10214000 {
+ compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0x10214000 0x4000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
+ <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ dmas = <&pdma 10>;
+ dma-names = "rx-tx";
+ fifo-depth = <256>;
+ max-frequency = <150000000>;
+ resets = <&cru SRST_SDMMC>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ sdio: mmc@10218000 {
+ compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0x10218000 0x4000>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
+ <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ dmas = <&pdma 11>;
+ dma-names = "rx-tx";
+ fifo-depth = <256>;
+ max-frequency = <150000000>;
+ resets = <&cru SRST_SDIO>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ emmc: mmc@1021c000 {
+ compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0x1021c000 0x4000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
+ <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ dmas = <&pdma 12>;
+ dma-names = "rx-tx";
+ fifo-depth = <256>;
+ max-frequency = <150000000>;
+ resets = <&cru SRST_EMMC>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ nfc: nand-controller@10500000 {
+ compatible = "rockchip,rk3128-nfc", "rockchip,rk2928-nfc";
+ reg = <0x10500000 0x4000>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>;
+ clock-names = "ahb", "nfc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_cs0
+ &flash_dqs &flash_rdn &flash_rdy &flash_wrn>;
+ status = "disabled";
+ };
+
+ cru: clock-controller@20000000 {
+ compatible = "rockchip,rk3128-cru";
+ reg = <0x20000000 0x1000>;
+ clocks = <&xin24m>;
+ clock-names = "xin24m";
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ assigned-clocks = <&cru PLL_GPLL>;
+ assigned-clock-rates = <594000000>;
+ };
+
+ grf: syscon@20008000 {
+ compatible = "rockchip,rk3128-grf", "syscon", "simple-mfd";
+ reg = <0x20008000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ usb2phy: usb2phy@17c {
+ compatible = "rockchip,rk3128-usb2phy";
+ reg = <0x017c 0x0c>;
+ clocks = <&cru SCLK_OTGPHY0>;
+ clock-names = "phyclk";
+ clock-output-names = "usb480m_phy";
+ #clock-cells = <0>;
+ status = "disabled";
+
+ usb2phy_host: host-port {
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "linestate";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ usb2phy_otg: otg-port {
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "otg-bvalid", "otg-id",
+ "linestate";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+ };
+ };
+
+ timer0: timer@20044000 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044000 0x20>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer1: timer@20044020 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044020 0x20>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer2: timer@20044040 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044040 0x20>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer3: timer@20044060 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044060 0x20>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer4: timer@20044080 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044080 0x20>;
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer5: timer@200440a0 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x200440a0 0x20>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ watchdog: watchdog@2004c000 {
+ compatible = "rockchip,rk3128-wdt", "snps,dw-wdt";
+ reg = <0x2004c000 0x100>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_WDT>;
+ status = "disabled";
+ };
+
+ pwm0: pwm@20050000 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050000 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm1: pwm@20050010 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050010 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm1_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@20050020 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050020 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@20050030 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050030 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@20056000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <0x20056000 0x1000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@2005a000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <0x2005a000 0x1000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@2005e000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <0x2005e000 0x1000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart0: serial@20060000 {
+ compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+ reg = <0x20060000 0x100>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&pdma 2>, <&pdma 3>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
+ uart1: serial@20064000 {
+ compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+ reg = <0x20064000 0x100>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&pdma 4>, <&pdma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_xfer>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
+ uart2: serial@20068000 {
+ compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+ reg = <0x20068000 0x100>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&pdma 6>, <&pdma 7>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_xfer>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
+ saradc: saradc@2006c000 {
+ compatible = "rockchip,saradc";
+ reg = <0x2006c000 0x100>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
+ clock-names = "saradc", "apb_pclk";
+ resets = <&cru SRST_SARADC>;
+ reset-names = "saradc-apb";
+ #io-channel-cells = <1>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@20072000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <20072000 0x1000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@20074000 {
+ compatible = "rockchip,rk3128-spi", "rockchip,rk3066-spi";
+ reg = <0x20074000 0x1000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
+ clock-names = "spiclk", "apb_pclk";
+ dmas = <&pdma 8>, <&pdma 9>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_tx &spi0_rx &spi0_clk &spi0_cs0 &spi0_cs1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ pdma: dma-controller@20078000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x20078000 0x4000>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ arm,pl330-broken-no-flushp;
+ clocks = <&cru ACLK_DMAC>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ };
+
+ pinctrl: pinctrl {
+ compatible = "rockchip,rk3128-pinctrl";
+ rockchip,grf = <&grf>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio0: gpio@2007c000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x2007c000 0x100>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@20080000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x20080000 0x100>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@20084000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x20084000 0x100>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@20088000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x20088000 0x100>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pcfg_pull_default: pcfg-pull-default {
+ bias-pull-pin-default;
+ };
+
+ pcfg_pull_none: pcfg-pull-none {
+ bias-disable;
+ };
+
+ emmc {
+ emmc_clk: emmc-clk {
+ rockchip,pins = <2 RK_PA7 2 &pcfg_pull_none>;
+ };
+
+ emmc_cmd: emmc-cmd {
+ rockchip,pins = <1 RK_PC6 2 &pcfg_pull_default>;
+ };
+
+ emmc_cmd1: emmc-cmd1 {
+ rockchip,pins = <2 RK_PA4 2 &pcfg_pull_default>;
+ };
+
+ emmc_pwr: emmc-pwr {
+ rockchip,pins = <2 RK_PA5 2 &pcfg_pull_default>;
+ };
+
+ emmc_bus1: emmc-bus1 {
+ rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>;
+ };
+
+ emmc_bus4: emmc-bus4 {
+ rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>,
+ <1 RK_PD1 2 &pcfg_pull_default>,
+ <1 RK_PD2 2 &pcfg_pull_default>,
+ <1 RK_PD3 2 &pcfg_pull_default>;
+ };
+
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>,
+ <1 RK_PD1 2 &pcfg_pull_default>,
+ <1 RK_PD2 2 &pcfg_pull_default>,
+ <1 RK_PD3 2 &pcfg_pull_default>,
+ <1 RK_PD4 2 &pcfg_pull_default>,
+ <1 RK_PD5 2 &pcfg_pull_default>,
+ <1 RK_PD6 2 &pcfg_pull_default>,
+ <1 RK_PD7 2 &pcfg_pull_default>;
+ };
+ };
+
+ gmac {
+ rgmii_pins: rgmii-pins {
+ rockchip,pins = <2 RK_PB0 3 &pcfg_pull_default>,
+ <2 RK_PB1 3 &pcfg_pull_default>,
+ <2 RK_PB3 3 &pcfg_pull_default>,
+ <2 RK_PB4 3 &pcfg_pull_default>,
+ <2 RK_PB5 3 &pcfg_pull_default>,
+ <2 RK_PB6 3 &pcfg_pull_default>,
+ <2 RK_PC0 3 &pcfg_pull_default>,
+ <2 RK_PC1 3 &pcfg_pull_default>,
+ <2 RK_PC2 3 &pcfg_pull_default>,
+ <2 RK_PC3 3 &pcfg_pull_default>,
+ <2 RK_PD1 3 &pcfg_pull_default>,
+ <2 RK_PC4 4 &pcfg_pull_default>,
+ <2 RK_PC5 4 &pcfg_pull_default>,
+ <2 RK_PC6 4 &pcfg_pull_default>,
+ <2 RK_PC7 4 &pcfg_pull_default>;
+ };
+
+ rmii_pins: rmii-pins {
+ rockchip,pins = <2 RK_PB0 3 &pcfg_pull_default>,
+ <2 RK_PB4 3 &pcfg_pull_default>,
+ <2 RK_PB5 3 &pcfg_pull_default>,
+ <2 RK_PB6 3 &pcfg_pull_default>,
+ <2 RK_PB7 3 &pcfg_pull_default>,
+ <2 RK_PC0 3 &pcfg_pull_default>,
+ <2 RK_PC1 3 &pcfg_pull_default>,
+ <2 RK_PC2 3 &pcfg_pull_default>,
+ <2 RK_PC3 3 &pcfg_pull_default>,
+ <2 RK_PD1 3 &pcfg_pull_default>;
+ };
+ };
+
+ hdmi {
+ hdmii2c_xfer: hdmii2c-xfer {
+ rockchip,pins = <0 RK_PA6 2 &pcfg_pull_none>,
+ <0 RK_PA7 2 &pcfg_pull_none>;
+ };
+
+ hdmi_hpd: hdmi-hpd {
+ rockchip,pins = <0 RK_PB7 1 &pcfg_pull_none>;
+ };
+
+ hdmi_cec: hdmi-cec {
+ rockchip,pins = <0 RK_PC4 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c0 {
+ i2c0_xfer: i2c0-xfer {
+ rockchip,pins = <0 RK_PA0 1 &pcfg_pull_none>,
+ <0 RK_PA1 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c1 {
+ i2c1_xfer: i2c1-xfer {
+ rockchip,pins = <0 RK_PA2 1 &pcfg_pull_none>,
+ <0 RK_PA3 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c2 {
+ i2c2_xfer: i2c2-xfer {
+ rockchip,pins = <2 RK_PC4 3 &pcfg_pull_none>,
+ <2 RK_PC5 3 &pcfg_pull_none>;
+ };
+ };
+
+ i2c3 {
+ i2c3_xfer: i2c3-xfer {
+ rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>,
+ <0 RK_PA7 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2s {
+ i2s_bus: i2s-bus {
+ rockchip,pins = <0 RK_PB0 1 &pcfg_pull_none>,
+ <0 RK_PB1 1 &pcfg_pull_none>,
+ <0 RK_PB3 1 &pcfg_pull_none>,
+ <0 RK_PB4 1 &pcfg_pull_none>,
+ <0 RK_PB5 1 &pcfg_pull_none>,
+ <0 RK_PB6 1 &pcfg_pull_none>;
+ };
+
+ i2s1_bus: i2s1-bus {
+ rockchip,pins = <1 RK_PA0 1 &pcfg_pull_none>,
+ <1 RK_PA1 1 &pcfg_pull_none>,
+ <1 RK_PA2 1 &pcfg_pull_none>,
+ <1 RK_PA3 1 &pcfg_pull_none>,
+ <1 RK_PA4 1 &pcfg_pull_none>,
+ <1 RK_PA5 1 &pcfg_pull_none>;
+ };
+ };
+
+ lcdc {
+ lcdc_dclk: lcdc-dclk {
+ rockchip,pins = <2 RK_PB0 1 &pcfg_pull_none>;
+ };
+
+ lcdc_den: lcdc-den {
+ rockchip,pins = <2 RK_PB3 1 &pcfg_pull_none>;
+ };
+
+ lcdc_hsync: lcdc-hsync {
+ rockchip,pins = <2 RK_PB1 1 &pcfg_pull_none>;
+ };
+
+ lcdc_vsync: lcdc-vsync {
+ rockchip,pins = <2 RK_PB2 1 &pcfg_pull_none>;
+ };
+
+ lcdc_rgb24: lcdc-rgb24 {
+ rockchip,pins = <2 RK_PB4 1 &pcfg_pull_none>,
+ <2 RK_PB5 1 &pcfg_pull_none>,
+ <2 RK_PB6 1 &pcfg_pull_none>,
+ <2 RK_PB7 1 &pcfg_pull_none>,
+ <2 RK_PC0 1 &pcfg_pull_none>,
+ <2 RK_PC1 1 &pcfg_pull_none>,
+ <2 RK_PC2 1 &pcfg_pull_none>,
+ <2 RK_PC3 1 &pcfg_pull_none>,
+ <2 RK_PC4 1 &pcfg_pull_none>,
+ <2 RK_PC5 1 &pcfg_pull_none>,
+ <2 RK_PC6 1 &pcfg_pull_none>,
+ <2 RK_PC7 1 &pcfg_pull_none>,
+ <2 RK_PD0 1 &pcfg_pull_none>,
+ <2 RK_PD1 1 &pcfg_pull_none>;
+ };
+ };
+
+ nfc {
+ flash_ale:flash-ale {
+ rockchip,pins = <2 RK_PA0 1 &pcfg_pull_none>;
+ };
+
+ flash_cle:flash-cle {
+ rockchip,pins = <2 RK_PA1 1 &pcfg_pull_none>;
+ };
+
+ flash_wrn:flash-wrn {
+ rockchip,pins = <2 RK_PA2 1 &pcfg_pull_none>;
+ };
+
+ flash_rdn:flash-rdn {
+ rockchip,pins = <2 RK_PA3 1 &pcfg_pull_none>;
+ };
+
+ flash_rdy:flash-rdy {
+ rockchip,pins = <2 RK_PA4 1 &pcfg_pull_none>;
+ };
+
+ flash_cs0:flash-cs0 {
+ rockchip,pins = <2 RK_PA6 1 &pcfg_pull_none>;
+ };
+
+ flash_dqs:flash-dqs {
+ rockchip,pins = <2 RK_PA7 1 &pcfg_pull_none>;
+ };
+
+ flash_bus8: flash-bus8 {
+ rockchip,pins = <1 RK_PD0 1 &pcfg_pull_none>,
+ <1 RK_PD1 1 &pcfg_pull_none>,
+ <1 RK_PD2 1 &pcfg_pull_none>,
+ <1 RK_PD3 1 &pcfg_pull_none>,
+ <1 RK_PD4 1 &pcfg_pull_none>,
+ <1 RK_PD5 1 &pcfg_pull_none>,
+ <1 RK_PD6 1 &pcfg_pull_none>,
+ <1 RK_PD7 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm0 {
+ pwm0_pin: pwm0-pin {
+ rockchip,pins = <0 RK_PD2 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm1 {
+ pwm1_pin: pwm1-pin {
+ rockchip,pins = <0 RK_PD3 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm2 {
+ pwm2_pin: pwm2-pin {
+ rockchip,pins = <0 RK_PD4 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm3 {
+ pwm3_pin: pwm3-pin {
+ rockchip,pins = <3 RK_PD2 1 &pcfg_pull_none>;
+ };
+ };
+
+ sdio {
+ sdio_clk: sdio-clk {
+ rockchip,pins = <1 RK_PA0 2 &pcfg_pull_none>;
+ };
+
+ sdio_cmd: sdio-cmd {
+ rockchip,pins = <0 RK_PA3 2 &pcfg_pull_default>;
+ };
+
+ sdio_pwren: sdio-pwren {
+ rockchip,pins = <0 RK_PD6 1 &pcfg_pull_default>;
+ };
+
+ sdio_bus4: sdio-bus4 {
+ rockchip,pins = <1 RK_PA1 2 &pcfg_pull_default>,
+ <1 RK_PA2 2 &pcfg_pull_default>,
+ <1 RK_PA4 2 &pcfg_pull_default>,
+ <1 RK_PA5 2 &pcfg_pull_default>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <1 RK_PC0 1 &pcfg_pull_none>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <1 RK_PB7 1 &pcfg_pull_default>;
+ };
+
+ sdmmc_wp: sdmmc-wp {
+ rockchip,pins = <1 RK_PA7 1 &pcfg_pull_default>;
+ };
+
+ sdmmc_pwren: sdmmc-pwren {
+ rockchip,pins = <1 RK_PB6 1 &pcfg_pull_default>;
+ };
+
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <1 RK_PC2 1 &pcfg_pull_default>,
+ <1 RK_PC3 1 &pcfg_pull_default>,
+ <1 RK_PC4 1 &pcfg_pull_default>,
+ <1 RK_PC5 1 &pcfg_pull_default>;
+ };
+ };
+
+ spdif {
+ spdif_tx: spdif-tx {
+ rockchip,pins = <3 RK_PD3 1 &pcfg_pull_none>;
+ };
+ };
+
+ spi0 {
+ spi0_clk: spi0-clk {
+ rockchip,pins = <1 RK_PB0 1 &pcfg_pull_default>;
+ };
+
+ spi0_cs0: spi0-cs0 {
+ rockchip,pins = <1 RK_PB3 1 &pcfg_pull_default>;
+ };
+
+ spi0_tx: spi0-tx {
+ rockchip,pins = <1 RK_PB1 1 &pcfg_pull_default>;
+ };
+
+ spi0_rx: spi0-rx {
+ rockchip,pins = <1 RK_PB2 1 &pcfg_pull_default>;
+ };
+
+ spi0_cs1: spi0-cs1 {
+ rockchip,pins = <1 RK_PB4 1 &pcfg_pull_default>;
+ };
+
+ spi1_clk: spi1-clk {
+ rockchip,pins = <2 RK_PA0 2 &pcfg_pull_default>;
+ };
+
+ spi1_cs0: spi1-cs0 {
+ rockchip,pins = <1 RK_PD6 3 &pcfg_pull_default>;
+ };
+
+ spi1_tx: spi1-tx {
+ rockchip,pins = <1 RK_PD5 3 &pcfg_pull_default>;
+ };
+
+ spi1_rx: spi1-rx {
+ rockchip,pins = <1 RK_PD4 3 &pcfg_pull_default>;
+ };
+
+ spi1_cs1: spi1-cs1 {
+ rockchip,pins = <1 RK_PD7 3 &pcfg_pull_default>;
+ };
+
+ spi2_clk: spi2-clk {
+ rockchip,pins = <0 RK_PB1 2 &pcfg_pull_default>;
+ };
+
+ spi2_cs0: spi2-cs0 {
+ rockchip,pins = <0 RK_PB6 2 &pcfg_pull_default>;
+ };
+
+ spi2_tx: spi2-tx {
+ rockchip,pins = <0 RK_PB3 2 &pcfg_pull_default>;
+ };
+
+ spi2_rx: spi2-rx {
+ rockchip,pins = <0 RK_PB5 2 &pcfg_pull_default>;
+ };
+ };
+
+ uart0 {
+ uart0_xfer: uart0-xfer {
+ rockchip,pins = <2 RK_PD2 2 &pcfg_pull_default>,
+ <2 RK_PD3 2 &pcfg_pull_none>;
+ };
+
+ uart0_cts: uart0-cts {
+ rockchip,pins = <2 RK_PD5 2 &pcfg_pull_none>;
+ };
+
+ uart0_rts: uart0-rts {
+ rockchip,pins = <0 RK_PC1 2 &pcfg_pull_none>;
+ };
+ };
+
+ uart1 {
+ uart1_xfer: uart1-xfer {
+ rockchip,pins = <1 RK_PB1 2 &pcfg_pull_default>,
+ <1 RK_PB2 2 &pcfg_pull_default>;
+ };
+
+ uart1_cts: uart1-cts {
+ rockchip,pins = <1 RK_PB0 2 &pcfg_pull_none>;
+ };
+
+ uart1_rts: uart1-rts {
+ rockchip,pins = <1 RK_PB3 2 &pcfg_pull_none>;
+ };
+ };
+
+ uart2 {
+ uart2_xfer: uart2-xfer {
+ rockchip,pins = <1 RK_PC2 2 &pcfg_pull_default>,
+ <1 RK_PC3 2 &pcfg_pull_none>;
+ };
+
+ uart2_cts: uart2-cts {
+ rockchip,pins = <0 RK_PD1 1 &pcfg_pull_none>;
+ };
+
+ uart2_rts: uart2-rts {
+ rockchip,pins = <0 RK_PD0 1 &pcfg_pull_none>;
+ };
+ };
+ };
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 3/4] ARM: dts: rockchip: add rk3128.dtsi
@ 2022-10-28 14:41 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add basic rk3128 support.
Features:
Quad-core ARM Cortex-A7MP Core processor
Clock & reset unit
Power management unit
Interrupt controller
DMAC
6x 64 bits Timers
4x PWMs
1x 32 bits watchdog
Internal memory:
Internal BootRom
Internal SRAM 8KB
External memory:
Dynamic Memory Interface (DDR3/DDR3L/LPDDR2)
Nand Flash Interface
eMMC Interface
SD/MMC Interface
Connectivity:
SDIO interface
SPI Controller
3x UART controller
4x I2C controllers
4x groups of GPIO (GPIO0~GPIO3), 32 GPIOs per group
USB Host2.0
USB OTG2.0
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
---
NOT TESTED WITH HARDWARE
NO THERMAL PROTECTION
---
Changed V2:
remove aliases
add gic interrupts mask defines
add virtual timer interrupts
---
arch/arm/boot/dts/rk3128.dtsi | 916 ++++++++++++++++++++++++++++++++++
1 file changed, 916 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3128.dtsi
diff --git a/arch/arm/boot/dts/rk3128.dtsi b/arch/arm/boot/dts/rk3128.dtsi
new file mode 100644
index 000000000..0480144c1
--- /dev/null
+++ b/arch/arm/boot/dts/rk3128.dtsi
@@ -0,0 +1,916 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2017 Rockchip Electronics Co., Ltd
+ */
+
+#include <dt-bindings/clock/rk3128-cru.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+
+/ {
+ compatible = "rockchip,rk3128";
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ arm-pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@f00 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf00>;
+ clock-latency = <40000>;
+ clocks = <&cru ARMCLK>;
+ operating-points = <
+ /* KHz uV */
+ 816000 1000000
+ >;
+ #cooling-cells = <2>; /* min followed by max */
+ };
+
+ cpu1: cpu@f01 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf01>;
+ };
+
+ cpu2: cpu@f02 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf02>;
+ };
+
+ cpu3: cpu@f03 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf03>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ arm,cpu-registers-not-fw-configured;
+ clock-frequency = <24000000>;
+ };
+
+ xin24m: oscillator {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xin24m";
+ #clock-cells = <0>;
+ };
+
+ pmu: syscon@100a0000 {
+ compatible = "rockchip,rk3128-pmu", "syscon", "simple-mfd";
+ reg = <0x100a0000 0x1000>;
+ };
+
+ gic: interrupt-controller@10139000 {
+ compatible = "arm,cortex-a7-gic";
+ reg = <0x10139000 0x1000>,
+ <0x1013a000 0x1000>,
+ <0x1013c000 0x2000>,
+ <0x1013e000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ };
+
+ usb_otg: usb@10180000 {
+ compatible = "rockchip,rk3128-usb", "rockchip,rk3066-usb", "snps,dwc2";
+ reg = <0x10180000 0x40000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_OTG>;
+ clock-names = "otg";
+ dr_mode = "otg";
+ phys = <&usb2phy_otg>;
+ phy-names = "usb2-phy";
+ status = "disabled";
+ };
+
+ usb_host_ehci: usb@101c0000 {
+ compatible = "generic-ehci";
+ reg = <0x101c0000 0x20000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2phy_host>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ usb_host_ohci: usb@101e0000 {
+ compatible = "generic-ohci";
+ reg = <0x101e0000 0x20000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2phy_host>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ sdmmc: mmc@10214000 {
+ compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0x10214000 0x4000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
+ <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ dmas = <&pdma 10>;
+ dma-names = "rx-tx";
+ fifo-depth = <256>;
+ max-frequency = <150000000>;
+ resets = <&cru SRST_SDMMC>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ sdio: mmc@10218000 {
+ compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0x10218000 0x4000>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
+ <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ dmas = <&pdma 11>;
+ dma-names = "rx-tx";
+ fifo-depth = <256>;
+ max-frequency = <150000000>;
+ resets = <&cru SRST_SDIO>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ emmc: mmc@1021c000 {
+ compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0x1021c000 0x4000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
+ <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ dmas = <&pdma 12>;
+ dma-names = "rx-tx";
+ fifo-depth = <256>;
+ max-frequency = <150000000>;
+ resets = <&cru SRST_EMMC>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ nfc: nand-controller@10500000 {
+ compatible = "rockchip,rk3128-nfc", "rockchip,rk2928-nfc";
+ reg = <0x10500000 0x4000>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>;
+ clock-names = "ahb", "nfc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_cs0
+ &flash_dqs &flash_rdn &flash_rdy &flash_wrn>;
+ status = "disabled";
+ };
+
+ cru: clock-controller@20000000 {
+ compatible = "rockchip,rk3128-cru";
+ reg = <0x20000000 0x1000>;
+ clocks = <&xin24m>;
+ clock-names = "xin24m";
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ assigned-clocks = <&cru PLL_GPLL>;
+ assigned-clock-rates = <594000000>;
+ };
+
+ grf: syscon@20008000 {
+ compatible = "rockchip,rk3128-grf", "syscon", "simple-mfd";
+ reg = <0x20008000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ usb2phy: usb2phy@17c {
+ compatible = "rockchip,rk3128-usb2phy";
+ reg = <0x017c 0x0c>;
+ clocks = <&cru SCLK_OTGPHY0>;
+ clock-names = "phyclk";
+ clock-output-names = "usb480m_phy";
+ #clock-cells = <0>;
+ status = "disabled";
+
+ usb2phy_host: host-port {
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "linestate";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ usb2phy_otg: otg-port {
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "otg-bvalid", "otg-id",
+ "linestate";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+ };
+ };
+
+ timer0: timer@20044000 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044000 0x20>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer1: timer@20044020 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044020 0x20>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer2: timer@20044040 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044040 0x20>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer3: timer@20044060 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044060 0x20>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer4: timer@20044080 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044080 0x20>;
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer5: timer@200440a0 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x200440a0 0x20>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ watchdog: watchdog@2004c000 {
+ compatible = "rockchip,rk3128-wdt", "snps,dw-wdt";
+ reg = <0x2004c000 0x100>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_WDT>;
+ status = "disabled";
+ };
+
+ pwm0: pwm@20050000 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050000 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm1: pwm@20050010 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050010 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm1_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@20050020 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050020 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@20050030 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050030 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@20056000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <0x20056000 0x1000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@2005a000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <0x2005a000 0x1000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@2005e000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <0x2005e000 0x1000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart0: serial@20060000 {
+ compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+ reg = <0x20060000 0x100>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&pdma 2>, <&pdma 3>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
+ uart1: serial@20064000 {
+ compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+ reg = <0x20064000 0x100>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&pdma 4>, <&pdma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_xfer>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
+ uart2: serial@20068000 {
+ compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+ reg = <0x20068000 0x100>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&pdma 6>, <&pdma 7>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_xfer>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
+ saradc: saradc@2006c000 {
+ compatible = "rockchip,saradc";
+ reg = <0x2006c000 0x100>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
+ clock-names = "saradc", "apb_pclk";
+ resets = <&cru SRST_SARADC>;
+ reset-names = "saradc-apb";
+ #io-channel-cells = <1>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@20072000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <20072000 0x1000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@20074000 {
+ compatible = "rockchip,rk3128-spi", "rockchip,rk3066-spi";
+ reg = <0x20074000 0x1000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
+ clock-names = "spiclk", "apb_pclk";
+ dmas = <&pdma 8>, <&pdma 9>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_tx &spi0_rx &spi0_clk &spi0_cs0 &spi0_cs1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ pdma: dma-controller@20078000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x20078000 0x4000>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ arm,pl330-broken-no-flushp;
+ clocks = <&cru ACLK_DMAC>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ };
+
+ pinctrl: pinctrl {
+ compatible = "rockchip,rk3128-pinctrl";
+ rockchip,grf = <&grf>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio0: gpio@2007c000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x2007c000 0x100>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@20080000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x20080000 0x100>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@20084000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x20084000 0x100>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@20088000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x20088000 0x100>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pcfg_pull_default: pcfg-pull-default {
+ bias-pull-pin-default;
+ };
+
+ pcfg_pull_none: pcfg-pull-none {
+ bias-disable;
+ };
+
+ emmc {
+ emmc_clk: emmc-clk {
+ rockchip,pins = <2 RK_PA7 2 &pcfg_pull_none>;
+ };
+
+ emmc_cmd: emmc-cmd {
+ rockchip,pins = <1 RK_PC6 2 &pcfg_pull_default>;
+ };
+
+ emmc_cmd1: emmc-cmd1 {
+ rockchip,pins = <2 RK_PA4 2 &pcfg_pull_default>;
+ };
+
+ emmc_pwr: emmc-pwr {
+ rockchip,pins = <2 RK_PA5 2 &pcfg_pull_default>;
+ };
+
+ emmc_bus1: emmc-bus1 {
+ rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>;
+ };
+
+ emmc_bus4: emmc-bus4 {
+ rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>,
+ <1 RK_PD1 2 &pcfg_pull_default>,
+ <1 RK_PD2 2 &pcfg_pull_default>,
+ <1 RK_PD3 2 &pcfg_pull_default>;
+ };
+
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>,
+ <1 RK_PD1 2 &pcfg_pull_default>,
+ <1 RK_PD2 2 &pcfg_pull_default>,
+ <1 RK_PD3 2 &pcfg_pull_default>,
+ <1 RK_PD4 2 &pcfg_pull_default>,
+ <1 RK_PD5 2 &pcfg_pull_default>,
+ <1 RK_PD6 2 &pcfg_pull_default>,
+ <1 RK_PD7 2 &pcfg_pull_default>;
+ };
+ };
+
+ gmac {
+ rgmii_pins: rgmii-pins {
+ rockchip,pins = <2 RK_PB0 3 &pcfg_pull_default>,
+ <2 RK_PB1 3 &pcfg_pull_default>,
+ <2 RK_PB3 3 &pcfg_pull_default>,
+ <2 RK_PB4 3 &pcfg_pull_default>,
+ <2 RK_PB5 3 &pcfg_pull_default>,
+ <2 RK_PB6 3 &pcfg_pull_default>,
+ <2 RK_PC0 3 &pcfg_pull_default>,
+ <2 RK_PC1 3 &pcfg_pull_default>,
+ <2 RK_PC2 3 &pcfg_pull_default>,
+ <2 RK_PC3 3 &pcfg_pull_default>,
+ <2 RK_PD1 3 &pcfg_pull_default>,
+ <2 RK_PC4 4 &pcfg_pull_default>,
+ <2 RK_PC5 4 &pcfg_pull_default>,
+ <2 RK_PC6 4 &pcfg_pull_default>,
+ <2 RK_PC7 4 &pcfg_pull_default>;
+ };
+
+ rmii_pins: rmii-pins {
+ rockchip,pins = <2 RK_PB0 3 &pcfg_pull_default>,
+ <2 RK_PB4 3 &pcfg_pull_default>,
+ <2 RK_PB5 3 &pcfg_pull_default>,
+ <2 RK_PB6 3 &pcfg_pull_default>,
+ <2 RK_PB7 3 &pcfg_pull_default>,
+ <2 RK_PC0 3 &pcfg_pull_default>,
+ <2 RK_PC1 3 &pcfg_pull_default>,
+ <2 RK_PC2 3 &pcfg_pull_default>,
+ <2 RK_PC3 3 &pcfg_pull_default>,
+ <2 RK_PD1 3 &pcfg_pull_default>;
+ };
+ };
+
+ hdmi {
+ hdmii2c_xfer: hdmii2c-xfer {
+ rockchip,pins = <0 RK_PA6 2 &pcfg_pull_none>,
+ <0 RK_PA7 2 &pcfg_pull_none>;
+ };
+
+ hdmi_hpd: hdmi-hpd {
+ rockchip,pins = <0 RK_PB7 1 &pcfg_pull_none>;
+ };
+
+ hdmi_cec: hdmi-cec {
+ rockchip,pins = <0 RK_PC4 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c0 {
+ i2c0_xfer: i2c0-xfer {
+ rockchip,pins = <0 RK_PA0 1 &pcfg_pull_none>,
+ <0 RK_PA1 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c1 {
+ i2c1_xfer: i2c1-xfer {
+ rockchip,pins = <0 RK_PA2 1 &pcfg_pull_none>,
+ <0 RK_PA3 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c2 {
+ i2c2_xfer: i2c2-xfer {
+ rockchip,pins = <2 RK_PC4 3 &pcfg_pull_none>,
+ <2 RK_PC5 3 &pcfg_pull_none>;
+ };
+ };
+
+ i2c3 {
+ i2c3_xfer: i2c3-xfer {
+ rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>,
+ <0 RK_PA7 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2s {
+ i2s_bus: i2s-bus {
+ rockchip,pins = <0 RK_PB0 1 &pcfg_pull_none>,
+ <0 RK_PB1 1 &pcfg_pull_none>,
+ <0 RK_PB3 1 &pcfg_pull_none>,
+ <0 RK_PB4 1 &pcfg_pull_none>,
+ <0 RK_PB5 1 &pcfg_pull_none>,
+ <0 RK_PB6 1 &pcfg_pull_none>;
+ };
+
+ i2s1_bus: i2s1-bus {
+ rockchip,pins = <1 RK_PA0 1 &pcfg_pull_none>,
+ <1 RK_PA1 1 &pcfg_pull_none>,
+ <1 RK_PA2 1 &pcfg_pull_none>,
+ <1 RK_PA3 1 &pcfg_pull_none>,
+ <1 RK_PA4 1 &pcfg_pull_none>,
+ <1 RK_PA5 1 &pcfg_pull_none>;
+ };
+ };
+
+ lcdc {
+ lcdc_dclk: lcdc-dclk {
+ rockchip,pins = <2 RK_PB0 1 &pcfg_pull_none>;
+ };
+
+ lcdc_den: lcdc-den {
+ rockchip,pins = <2 RK_PB3 1 &pcfg_pull_none>;
+ };
+
+ lcdc_hsync: lcdc-hsync {
+ rockchip,pins = <2 RK_PB1 1 &pcfg_pull_none>;
+ };
+
+ lcdc_vsync: lcdc-vsync {
+ rockchip,pins = <2 RK_PB2 1 &pcfg_pull_none>;
+ };
+
+ lcdc_rgb24: lcdc-rgb24 {
+ rockchip,pins = <2 RK_PB4 1 &pcfg_pull_none>,
+ <2 RK_PB5 1 &pcfg_pull_none>,
+ <2 RK_PB6 1 &pcfg_pull_none>,
+ <2 RK_PB7 1 &pcfg_pull_none>,
+ <2 RK_PC0 1 &pcfg_pull_none>,
+ <2 RK_PC1 1 &pcfg_pull_none>,
+ <2 RK_PC2 1 &pcfg_pull_none>,
+ <2 RK_PC3 1 &pcfg_pull_none>,
+ <2 RK_PC4 1 &pcfg_pull_none>,
+ <2 RK_PC5 1 &pcfg_pull_none>,
+ <2 RK_PC6 1 &pcfg_pull_none>,
+ <2 RK_PC7 1 &pcfg_pull_none>,
+ <2 RK_PD0 1 &pcfg_pull_none>,
+ <2 RK_PD1 1 &pcfg_pull_none>;
+ };
+ };
+
+ nfc {
+ flash_ale:flash-ale {
+ rockchip,pins = <2 RK_PA0 1 &pcfg_pull_none>;
+ };
+
+ flash_cle:flash-cle {
+ rockchip,pins = <2 RK_PA1 1 &pcfg_pull_none>;
+ };
+
+ flash_wrn:flash-wrn {
+ rockchip,pins = <2 RK_PA2 1 &pcfg_pull_none>;
+ };
+
+ flash_rdn:flash-rdn {
+ rockchip,pins = <2 RK_PA3 1 &pcfg_pull_none>;
+ };
+
+ flash_rdy:flash-rdy {
+ rockchip,pins = <2 RK_PA4 1 &pcfg_pull_none>;
+ };
+
+ flash_cs0:flash-cs0 {
+ rockchip,pins = <2 RK_PA6 1 &pcfg_pull_none>;
+ };
+
+ flash_dqs:flash-dqs {
+ rockchip,pins = <2 RK_PA7 1 &pcfg_pull_none>;
+ };
+
+ flash_bus8: flash-bus8 {
+ rockchip,pins = <1 RK_PD0 1 &pcfg_pull_none>,
+ <1 RK_PD1 1 &pcfg_pull_none>,
+ <1 RK_PD2 1 &pcfg_pull_none>,
+ <1 RK_PD3 1 &pcfg_pull_none>,
+ <1 RK_PD4 1 &pcfg_pull_none>,
+ <1 RK_PD5 1 &pcfg_pull_none>,
+ <1 RK_PD6 1 &pcfg_pull_none>,
+ <1 RK_PD7 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm0 {
+ pwm0_pin: pwm0-pin {
+ rockchip,pins = <0 RK_PD2 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm1 {
+ pwm1_pin: pwm1-pin {
+ rockchip,pins = <0 RK_PD3 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm2 {
+ pwm2_pin: pwm2-pin {
+ rockchip,pins = <0 RK_PD4 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm3 {
+ pwm3_pin: pwm3-pin {
+ rockchip,pins = <3 RK_PD2 1 &pcfg_pull_none>;
+ };
+ };
+
+ sdio {
+ sdio_clk: sdio-clk {
+ rockchip,pins = <1 RK_PA0 2 &pcfg_pull_none>;
+ };
+
+ sdio_cmd: sdio-cmd {
+ rockchip,pins = <0 RK_PA3 2 &pcfg_pull_default>;
+ };
+
+ sdio_pwren: sdio-pwren {
+ rockchip,pins = <0 RK_PD6 1 &pcfg_pull_default>;
+ };
+
+ sdio_bus4: sdio-bus4 {
+ rockchip,pins = <1 RK_PA1 2 &pcfg_pull_default>,
+ <1 RK_PA2 2 &pcfg_pull_default>,
+ <1 RK_PA4 2 &pcfg_pull_default>,
+ <1 RK_PA5 2 &pcfg_pull_default>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <1 RK_PC0 1 &pcfg_pull_none>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <1 RK_PB7 1 &pcfg_pull_default>;
+ };
+
+ sdmmc_wp: sdmmc-wp {
+ rockchip,pins = <1 RK_PA7 1 &pcfg_pull_default>;
+ };
+
+ sdmmc_pwren: sdmmc-pwren {
+ rockchip,pins = <1 RK_PB6 1 &pcfg_pull_default>;
+ };
+
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <1 RK_PC2 1 &pcfg_pull_default>,
+ <1 RK_PC3 1 &pcfg_pull_default>,
+ <1 RK_PC4 1 &pcfg_pull_default>,
+ <1 RK_PC5 1 &pcfg_pull_default>;
+ };
+ };
+
+ spdif {
+ spdif_tx: spdif-tx {
+ rockchip,pins = <3 RK_PD3 1 &pcfg_pull_none>;
+ };
+ };
+
+ spi0 {
+ spi0_clk: spi0-clk {
+ rockchip,pins = <1 RK_PB0 1 &pcfg_pull_default>;
+ };
+
+ spi0_cs0: spi0-cs0 {
+ rockchip,pins = <1 RK_PB3 1 &pcfg_pull_default>;
+ };
+
+ spi0_tx: spi0-tx {
+ rockchip,pins = <1 RK_PB1 1 &pcfg_pull_default>;
+ };
+
+ spi0_rx: spi0-rx {
+ rockchip,pins = <1 RK_PB2 1 &pcfg_pull_default>;
+ };
+
+ spi0_cs1: spi0-cs1 {
+ rockchip,pins = <1 RK_PB4 1 &pcfg_pull_default>;
+ };
+
+ spi1_clk: spi1-clk {
+ rockchip,pins = <2 RK_PA0 2 &pcfg_pull_default>;
+ };
+
+ spi1_cs0: spi1-cs0 {
+ rockchip,pins = <1 RK_PD6 3 &pcfg_pull_default>;
+ };
+
+ spi1_tx: spi1-tx {
+ rockchip,pins = <1 RK_PD5 3 &pcfg_pull_default>;
+ };
+
+ spi1_rx: spi1-rx {
+ rockchip,pins = <1 RK_PD4 3 &pcfg_pull_default>;
+ };
+
+ spi1_cs1: spi1-cs1 {
+ rockchip,pins = <1 RK_PD7 3 &pcfg_pull_default>;
+ };
+
+ spi2_clk: spi2-clk {
+ rockchip,pins = <0 RK_PB1 2 &pcfg_pull_default>;
+ };
+
+ spi2_cs0: spi2-cs0 {
+ rockchip,pins = <0 RK_PB6 2 &pcfg_pull_default>;
+ };
+
+ spi2_tx: spi2-tx {
+ rockchip,pins = <0 RK_PB3 2 &pcfg_pull_default>;
+ };
+
+ spi2_rx: spi2-rx {
+ rockchip,pins = <0 RK_PB5 2 &pcfg_pull_default>;
+ };
+ };
+
+ uart0 {
+ uart0_xfer: uart0-xfer {
+ rockchip,pins = <2 RK_PD2 2 &pcfg_pull_default>,
+ <2 RK_PD3 2 &pcfg_pull_none>;
+ };
+
+ uart0_cts: uart0-cts {
+ rockchip,pins = <2 RK_PD5 2 &pcfg_pull_none>;
+ };
+
+ uart0_rts: uart0-rts {
+ rockchip,pins = <0 RK_PC1 2 &pcfg_pull_none>;
+ };
+ };
+
+ uart1 {
+ uart1_xfer: uart1-xfer {
+ rockchip,pins = <1 RK_PB1 2 &pcfg_pull_default>,
+ <1 RK_PB2 2 &pcfg_pull_default>;
+ };
+
+ uart1_cts: uart1-cts {
+ rockchip,pins = <1 RK_PB0 2 &pcfg_pull_none>;
+ };
+
+ uart1_rts: uart1-rts {
+ rockchip,pins = <1 RK_PB3 2 &pcfg_pull_none>;
+ };
+ };
+
+ uart2 {
+ uart2_xfer: uart2-xfer {
+ rockchip,pins = <1 RK_PC2 2 &pcfg_pull_default>,
+ <1 RK_PC3 2 &pcfg_pull_none>;
+ };
+
+ uart2_cts: uart2-cts {
+ rockchip,pins = <0 RK_PD1 1 &pcfg_pull_none>;
+ };
+
+ uart2_rts: uart2-rts {
+ rockchip,pins = <0 RK_PD0 1 &pcfg_pull_none>;
+ };
+ };
+ };
+};
--
2.20.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 3/4] ARM: dts: rockchip: add rk3128.dtsi
@ 2022-10-28 14:41 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add basic rk3128 support.
Features:
Quad-core ARM Cortex-A7MP Core processor
Clock & reset unit
Power management unit
Interrupt controller
DMAC
6x 64 bits Timers
4x PWMs
1x 32 bits watchdog
Internal memory:
Internal BootRom
Internal SRAM 8KB
External memory:
Dynamic Memory Interface (DDR3/DDR3L/LPDDR2)
Nand Flash Interface
eMMC Interface
SD/MMC Interface
Connectivity:
SDIO interface
SPI Controller
3x UART controller
4x I2C controllers
4x groups of GPIO (GPIO0~GPIO3), 32 GPIOs per group
USB Host2.0
USB OTG2.0
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
---
NOT TESTED WITH HARDWARE
NO THERMAL PROTECTION
---
Changed V2:
remove aliases
add gic interrupts mask defines
add virtual timer interrupts
---
arch/arm/boot/dts/rk3128.dtsi | 916 ++++++++++++++++++++++++++++++++++
1 file changed, 916 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3128.dtsi
diff --git a/arch/arm/boot/dts/rk3128.dtsi b/arch/arm/boot/dts/rk3128.dtsi
new file mode 100644
index 000000000..0480144c1
--- /dev/null
+++ b/arch/arm/boot/dts/rk3128.dtsi
@@ -0,0 +1,916 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2017 Rockchip Electronics Co., Ltd
+ */
+
+#include <dt-bindings/clock/rk3128-cru.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+
+/ {
+ compatible = "rockchip,rk3128";
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ arm-pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@f00 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf00>;
+ clock-latency = <40000>;
+ clocks = <&cru ARMCLK>;
+ operating-points = <
+ /* KHz uV */
+ 816000 1000000
+ >;
+ #cooling-cells = <2>; /* min followed by max */
+ };
+
+ cpu1: cpu@f01 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf01>;
+ };
+
+ cpu2: cpu@f02 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf02>;
+ };
+
+ cpu3: cpu@f03 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf03>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ arm,cpu-registers-not-fw-configured;
+ clock-frequency = <24000000>;
+ };
+
+ xin24m: oscillator {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xin24m";
+ #clock-cells = <0>;
+ };
+
+ pmu: syscon@100a0000 {
+ compatible = "rockchip,rk3128-pmu", "syscon", "simple-mfd";
+ reg = <0x100a0000 0x1000>;
+ };
+
+ gic: interrupt-controller@10139000 {
+ compatible = "arm,cortex-a7-gic";
+ reg = <0x10139000 0x1000>,
+ <0x1013a000 0x1000>,
+ <0x1013c000 0x2000>,
+ <0x1013e000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ };
+
+ usb_otg: usb@10180000 {
+ compatible = "rockchip,rk3128-usb", "rockchip,rk3066-usb", "snps,dwc2";
+ reg = <0x10180000 0x40000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_OTG>;
+ clock-names = "otg";
+ dr_mode = "otg";
+ phys = <&usb2phy_otg>;
+ phy-names = "usb2-phy";
+ status = "disabled";
+ };
+
+ usb_host_ehci: usb@101c0000 {
+ compatible = "generic-ehci";
+ reg = <0x101c0000 0x20000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2phy_host>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ usb_host_ohci: usb@101e0000 {
+ compatible = "generic-ohci";
+ reg = <0x101e0000 0x20000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2phy_host>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ sdmmc: mmc@10214000 {
+ compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0x10214000 0x4000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
+ <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ dmas = <&pdma 10>;
+ dma-names = "rx-tx";
+ fifo-depth = <256>;
+ max-frequency = <150000000>;
+ resets = <&cru SRST_SDMMC>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ sdio: mmc@10218000 {
+ compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0x10218000 0x4000>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
+ <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ dmas = <&pdma 11>;
+ dma-names = "rx-tx";
+ fifo-depth = <256>;
+ max-frequency = <150000000>;
+ resets = <&cru SRST_SDIO>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ emmc: mmc@1021c000 {
+ compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0x1021c000 0x4000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
+ <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ dmas = <&pdma 12>;
+ dma-names = "rx-tx";
+ fifo-depth = <256>;
+ max-frequency = <150000000>;
+ resets = <&cru SRST_EMMC>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ nfc: nand-controller@10500000 {
+ compatible = "rockchip,rk3128-nfc", "rockchip,rk2928-nfc";
+ reg = <0x10500000 0x4000>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>;
+ clock-names = "ahb", "nfc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_cs0
+ &flash_dqs &flash_rdn &flash_rdy &flash_wrn>;
+ status = "disabled";
+ };
+
+ cru: clock-controller@20000000 {
+ compatible = "rockchip,rk3128-cru";
+ reg = <0x20000000 0x1000>;
+ clocks = <&xin24m>;
+ clock-names = "xin24m";
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ assigned-clocks = <&cru PLL_GPLL>;
+ assigned-clock-rates = <594000000>;
+ };
+
+ grf: syscon@20008000 {
+ compatible = "rockchip,rk3128-grf", "syscon", "simple-mfd";
+ reg = <0x20008000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ usb2phy: usb2phy@17c {
+ compatible = "rockchip,rk3128-usb2phy";
+ reg = <0x017c 0x0c>;
+ clocks = <&cru SCLK_OTGPHY0>;
+ clock-names = "phyclk";
+ clock-output-names = "usb480m_phy";
+ #clock-cells = <0>;
+ status = "disabled";
+
+ usb2phy_host: host-port {
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "linestate";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ usb2phy_otg: otg-port {
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "otg-bvalid", "otg-id",
+ "linestate";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+ };
+ };
+
+ timer0: timer@20044000 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044000 0x20>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer1: timer@20044020 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044020 0x20>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer2: timer@20044040 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044040 0x20>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer3: timer@20044060 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044060 0x20>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer4: timer@20044080 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x20044080 0x20>;
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ timer5: timer@200440a0 {
+ compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+ reg = <0x200440a0 0x20>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&xin24m>;
+ clock-names = "pclk", "timer";
+ };
+
+ watchdog: watchdog@2004c000 {
+ compatible = "rockchip,rk3128-wdt", "snps,dw-wdt";
+ reg = <0x2004c000 0x100>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_WDT>;
+ status = "disabled";
+ };
+
+ pwm0: pwm@20050000 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050000 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm1: pwm@20050010 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050010 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm1_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@20050020 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050020 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@20050030 {
+ compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+ reg = <0x20050030 0x10>;
+ clocks = <&cru PCLK_PWM>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@20056000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <0x20056000 0x1000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@2005a000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <0x2005a000 0x1000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@2005e000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <0x2005e000 0x1000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart0: serial@20060000 {
+ compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+ reg = <0x20060000 0x100>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&pdma 2>, <&pdma 3>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
+ uart1: serial@20064000 {
+ compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+ reg = <0x20064000 0x100>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&pdma 4>, <&pdma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_xfer>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
+ uart2: serial@20068000 {
+ compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+ reg = <0x20068000 0x100>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&pdma 6>, <&pdma 7>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_xfer>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
+ saradc: saradc@2006c000 {
+ compatible = "rockchip,saradc";
+ reg = <0x2006c000 0x100>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
+ clock-names = "saradc", "apb_pclk";
+ resets = <&cru SRST_SARADC>;
+ reset-names = "saradc-apb";
+ #io-channel-cells = <1>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@20072000 {
+ compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+ reg = <20072000 0x1000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@20074000 {
+ compatible = "rockchip,rk3128-spi", "rockchip,rk3066-spi";
+ reg = <0x20074000 0x1000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
+ clock-names = "spiclk", "apb_pclk";
+ dmas = <&pdma 8>, <&pdma 9>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_tx &spi0_rx &spi0_clk &spi0_cs0 &spi0_cs1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ pdma: dma-controller@20078000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x20078000 0x4000>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ arm,pl330-broken-no-flushp;
+ clocks = <&cru ACLK_DMAC>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ };
+
+ pinctrl: pinctrl {
+ compatible = "rockchip,rk3128-pinctrl";
+ rockchip,grf = <&grf>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio0: gpio@2007c000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x2007c000 0x100>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@20080000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x20080000 0x100>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@20084000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x20084000 0x100>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@20088000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x20088000 0x100>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pcfg_pull_default: pcfg-pull-default {
+ bias-pull-pin-default;
+ };
+
+ pcfg_pull_none: pcfg-pull-none {
+ bias-disable;
+ };
+
+ emmc {
+ emmc_clk: emmc-clk {
+ rockchip,pins = <2 RK_PA7 2 &pcfg_pull_none>;
+ };
+
+ emmc_cmd: emmc-cmd {
+ rockchip,pins = <1 RK_PC6 2 &pcfg_pull_default>;
+ };
+
+ emmc_cmd1: emmc-cmd1 {
+ rockchip,pins = <2 RK_PA4 2 &pcfg_pull_default>;
+ };
+
+ emmc_pwr: emmc-pwr {
+ rockchip,pins = <2 RK_PA5 2 &pcfg_pull_default>;
+ };
+
+ emmc_bus1: emmc-bus1 {
+ rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>;
+ };
+
+ emmc_bus4: emmc-bus4 {
+ rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>,
+ <1 RK_PD1 2 &pcfg_pull_default>,
+ <1 RK_PD2 2 &pcfg_pull_default>,
+ <1 RK_PD3 2 &pcfg_pull_default>;
+ };
+
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>,
+ <1 RK_PD1 2 &pcfg_pull_default>,
+ <1 RK_PD2 2 &pcfg_pull_default>,
+ <1 RK_PD3 2 &pcfg_pull_default>,
+ <1 RK_PD4 2 &pcfg_pull_default>,
+ <1 RK_PD5 2 &pcfg_pull_default>,
+ <1 RK_PD6 2 &pcfg_pull_default>,
+ <1 RK_PD7 2 &pcfg_pull_default>;
+ };
+ };
+
+ gmac {
+ rgmii_pins: rgmii-pins {
+ rockchip,pins = <2 RK_PB0 3 &pcfg_pull_default>,
+ <2 RK_PB1 3 &pcfg_pull_default>,
+ <2 RK_PB3 3 &pcfg_pull_default>,
+ <2 RK_PB4 3 &pcfg_pull_default>,
+ <2 RK_PB5 3 &pcfg_pull_default>,
+ <2 RK_PB6 3 &pcfg_pull_default>,
+ <2 RK_PC0 3 &pcfg_pull_default>,
+ <2 RK_PC1 3 &pcfg_pull_default>,
+ <2 RK_PC2 3 &pcfg_pull_default>,
+ <2 RK_PC3 3 &pcfg_pull_default>,
+ <2 RK_PD1 3 &pcfg_pull_default>,
+ <2 RK_PC4 4 &pcfg_pull_default>,
+ <2 RK_PC5 4 &pcfg_pull_default>,
+ <2 RK_PC6 4 &pcfg_pull_default>,
+ <2 RK_PC7 4 &pcfg_pull_default>;
+ };
+
+ rmii_pins: rmii-pins {
+ rockchip,pins = <2 RK_PB0 3 &pcfg_pull_default>,
+ <2 RK_PB4 3 &pcfg_pull_default>,
+ <2 RK_PB5 3 &pcfg_pull_default>,
+ <2 RK_PB6 3 &pcfg_pull_default>,
+ <2 RK_PB7 3 &pcfg_pull_default>,
+ <2 RK_PC0 3 &pcfg_pull_default>,
+ <2 RK_PC1 3 &pcfg_pull_default>,
+ <2 RK_PC2 3 &pcfg_pull_default>,
+ <2 RK_PC3 3 &pcfg_pull_default>,
+ <2 RK_PD1 3 &pcfg_pull_default>;
+ };
+ };
+
+ hdmi {
+ hdmii2c_xfer: hdmii2c-xfer {
+ rockchip,pins = <0 RK_PA6 2 &pcfg_pull_none>,
+ <0 RK_PA7 2 &pcfg_pull_none>;
+ };
+
+ hdmi_hpd: hdmi-hpd {
+ rockchip,pins = <0 RK_PB7 1 &pcfg_pull_none>;
+ };
+
+ hdmi_cec: hdmi-cec {
+ rockchip,pins = <0 RK_PC4 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c0 {
+ i2c0_xfer: i2c0-xfer {
+ rockchip,pins = <0 RK_PA0 1 &pcfg_pull_none>,
+ <0 RK_PA1 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c1 {
+ i2c1_xfer: i2c1-xfer {
+ rockchip,pins = <0 RK_PA2 1 &pcfg_pull_none>,
+ <0 RK_PA3 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c2 {
+ i2c2_xfer: i2c2-xfer {
+ rockchip,pins = <2 RK_PC4 3 &pcfg_pull_none>,
+ <2 RK_PC5 3 &pcfg_pull_none>;
+ };
+ };
+
+ i2c3 {
+ i2c3_xfer: i2c3-xfer {
+ rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>,
+ <0 RK_PA7 1 &pcfg_pull_none>;
+ };
+ };
+
+ i2s {
+ i2s_bus: i2s-bus {
+ rockchip,pins = <0 RK_PB0 1 &pcfg_pull_none>,
+ <0 RK_PB1 1 &pcfg_pull_none>,
+ <0 RK_PB3 1 &pcfg_pull_none>,
+ <0 RK_PB4 1 &pcfg_pull_none>,
+ <0 RK_PB5 1 &pcfg_pull_none>,
+ <0 RK_PB6 1 &pcfg_pull_none>;
+ };
+
+ i2s1_bus: i2s1-bus {
+ rockchip,pins = <1 RK_PA0 1 &pcfg_pull_none>,
+ <1 RK_PA1 1 &pcfg_pull_none>,
+ <1 RK_PA2 1 &pcfg_pull_none>,
+ <1 RK_PA3 1 &pcfg_pull_none>,
+ <1 RK_PA4 1 &pcfg_pull_none>,
+ <1 RK_PA5 1 &pcfg_pull_none>;
+ };
+ };
+
+ lcdc {
+ lcdc_dclk: lcdc-dclk {
+ rockchip,pins = <2 RK_PB0 1 &pcfg_pull_none>;
+ };
+
+ lcdc_den: lcdc-den {
+ rockchip,pins = <2 RK_PB3 1 &pcfg_pull_none>;
+ };
+
+ lcdc_hsync: lcdc-hsync {
+ rockchip,pins = <2 RK_PB1 1 &pcfg_pull_none>;
+ };
+
+ lcdc_vsync: lcdc-vsync {
+ rockchip,pins = <2 RK_PB2 1 &pcfg_pull_none>;
+ };
+
+ lcdc_rgb24: lcdc-rgb24 {
+ rockchip,pins = <2 RK_PB4 1 &pcfg_pull_none>,
+ <2 RK_PB5 1 &pcfg_pull_none>,
+ <2 RK_PB6 1 &pcfg_pull_none>,
+ <2 RK_PB7 1 &pcfg_pull_none>,
+ <2 RK_PC0 1 &pcfg_pull_none>,
+ <2 RK_PC1 1 &pcfg_pull_none>,
+ <2 RK_PC2 1 &pcfg_pull_none>,
+ <2 RK_PC3 1 &pcfg_pull_none>,
+ <2 RK_PC4 1 &pcfg_pull_none>,
+ <2 RK_PC5 1 &pcfg_pull_none>,
+ <2 RK_PC6 1 &pcfg_pull_none>,
+ <2 RK_PC7 1 &pcfg_pull_none>,
+ <2 RK_PD0 1 &pcfg_pull_none>,
+ <2 RK_PD1 1 &pcfg_pull_none>;
+ };
+ };
+
+ nfc {
+ flash_ale:flash-ale {
+ rockchip,pins = <2 RK_PA0 1 &pcfg_pull_none>;
+ };
+
+ flash_cle:flash-cle {
+ rockchip,pins = <2 RK_PA1 1 &pcfg_pull_none>;
+ };
+
+ flash_wrn:flash-wrn {
+ rockchip,pins = <2 RK_PA2 1 &pcfg_pull_none>;
+ };
+
+ flash_rdn:flash-rdn {
+ rockchip,pins = <2 RK_PA3 1 &pcfg_pull_none>;
+ };
+
+ flash_rdy:flash-rdy {
+ rockchip,pins = <2 RK_PA4 1 &pcfg_pull_none>;
+ };
+
+ flash_cs0:flash-cs0 {
+ rockchip,pins = <2 RK_PA6 1 &pcfg_pull_none>;
+ };
+
+ flash_dqs:flash-dqs {
+ rockchip,pins = <2 RK_PA7 1 &pcfg_pull_none>;
+ };
+
+ flash_bus8: flash-bus8 {
+ rockchip,pins = <1 RK_PD0 1 &pcfg_pull_none>,
+ <1 RK_PD1 1 &pcfg_pull_none>,
+ <1 RK_PD2 1 &pcfg_pull_none>,
+ <1 RK_PD3 1 &pcfg_pull_none>,
+ <1 RK_PD4 1 &pcfg_pull_none>,
+ <1 RK_PD5 1 &pcfg_pull_none>,
+ <1 RK_PD6 1 &pcfg_pull_none>,
+ <1 RK_PD7 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm0 {
+ pwm0_pin: pwm0-pin {
+ rockchip,pins = <0 RK_PD2 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm1 {
+ pwm1_pin: pwm1-pin {
+ rockchip,pins = <0 RK_PD3 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm2 {
+ pwm2_pin: pwm2-pin {
+ rockchip,pins = <0 RK_PD4 1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm3 {
+ pwm3_pin: pwm3-pin {
+ rockchip,pins = <3 RK_PD2 1 &pcfg_pull_none>;
+ };
+ };
+
+ sdio {
+ sdio_clk: sdio-clk {
+ rockchip,pins = <1 RK_PA0 2 &pcfg_pull_none>;
+ };
+
+ sdio_cmd: sdio-cmd {
+ rockchip,pins = <0 RK_PA3 2 &pcfg_pull_default>;
+ };
+
+ sdio_pwren: sdio-pwren {
+ rockchip,pins = <0 RK_PD6 1 &pcfg_pull_default>;
+ };
+
+ sdio_bus4: sdio-bus4 {
+ rockchip,pins = <1 RK_PA1 2 &pcfg_pull_default>,
+ <1 RK_PA2 2 &pcfg_pull_default>,
+ <1 RK_PA4 2 &pcfg_pull_default>,
+ <1 RK_PA5 2 &pcfg_pull_default>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <1 RK_PC0 1 &pcfg_pull_none>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <1 RK_PB7 1 &pcfg_pull_default>;
+ };
+
+ sdmmc_wp: sdmmc-wp {
+ rockchip,pins = <1 RK_PA7 1 &pcfg_pull_default>;
+ };
+
+ sdmmc_pwren: sdmmc-pwren {
+ rockchip,pins = <1 RK_PB6 1 &pcfg_pull_default>;
+ };
+
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <1 RK_PC2 1 &pcfg_pull_default>,
+ <1 RK_PC3 1 &pcfg_pull_default>,
+ <1 RK_PC4 1 &pcfg_pull_default>,
+ <1 RK_PC5 1 &pcfg_pull_default>;
+ };
+ };
+
+ spdif {
+ spdif_tx: spdif-tx {
+ rockchip,pins = <3 RK_PD3 1 &pcfg_pull_none>;
+ };
+ };
+
+ spi0 {
+ spi0_clk: spi0-clk {
+ rockchip,pins = <1 RK_PB0 1 &pcfg_pull_default>;
+ };
+
+ spi0_cs0: spi0-cs0 {
+ rockchip,pins = <1 RK_PB3 1 &pcfg_pull_default>;
+ };
+
+ spi0_tx: spi0-tx {
+ rockchip,pins = <1 RK_PB1 1 &pcfg_pull_default>;
+ };
+
+ spi0_rx: spi0-rx {
+ rockchip,pins = <1 RK_PB2 1 &pcfg_pull_default>;
+ };
+
+ spi0_cs1: spi0-cs1 {
+ rockchip,pins = <1 RK_PB4 1 &pcfg_pull_default>;
+ };
+
+ spi1_clk: spi1-clk {
+ rockchip,pins = <2 RK_PA0 2 &pcfg_pull_default>;
+ };
+
+ spi1_cs0: spi1-cs0 {
+ rockchip,pins = <1 RK_PD6 3 &pcfg_pull_default>;
+ };
+
+ spi1_tx: spi1-tx {
+ rockchip,pins = <1 RK_PD5 3 &pcfg_pull_default>;
+ };
+
+ spi1_rx: spi1-rx {
+ rockchip,pins = <1 RK_PD4 3 &pcfg_pull_default>;
+ };
+
+ spi1_cs1: spi1-cs1 {
+ rockchip,pins = <1 RK_PD7 3 &pcfg_pull_default>;
+ };
+
+ spi2_clk: spi2-clk {
+ rockchip,pins = <0 RK_PB1 2 &pcfg_pull_default>;
+ };
+
+ spi2_cs0: spi2-cs0 {
+ rockchip,pins = <0 RK_PB6 2 &pcfg_pull_default>;
+ };
+
+ spi2_tx: spi2-tx {
+ rockchip,pins = <0 RK_PB3 2 &pcfg_pull_default>;
+ };
+
+ spi2_rx: spi2-rx {
+ rockchip,pins = <0 RK_PB5 2 &pcfg_pull_default>;
+ };
+ };
+
+ uart0 {
+ uart0_xfer: uart0-xfer {
+ rockchip,pins = <2 RK_PD2 2 &pcfg_pull_default>,
+ <2 RK_PD3 2 &pcfg_pull_none>;
+ };
+
+ uart0_cts: uart0-cts {
+ rockchip,pins = <2 RK_PD5 2 &pcfg_pull_none>;
+ };
+
+ uart0_rts: uart0-rts {
+ rockchip,pins = <0 RK_PC1 2 &pcfg_pull_none>;
+ };
+ };
+
+ uart1 {
+ uart1_xfer: uart1-xfer {
+ rockchip,pins = <1 RK_PB1 2 &pcfg_pull_default>,
+ <1 RK_PB2 2 &pcfg_pull_default>;
+ };
+
+ uart1_cts: uart1-cts {
+ rockchip,pins = <1 RK_PB0 2 &pcfg_pull_none>;
+ };
+
+ uart1_rts: uart1-rts {
+ rockchip,pins = <1 RK_PB3 2 &pcfg_pull_none>;
+ };
+ };
+
+ uart2 {
+ uart2_xfer: uart2-xfer {
+ rockchip,pins = <1 RK_PC2 2 &pcfg_pull_default>,
+ <1 RK_PC3 2 &pcfg_pull_none>;
+ };
+
+ uart2_cts: uart2-cts {
+ rockchip,pins = <0 RK_PD1 1 &pcfg_pull_none>;
+ };
+
+ uart2_rts: uart2-rts {
+ rockchip,pins = <0 RK_PD0 1 &pcfg_pull_none>;
+ };
+ };
+ };
+};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 4/4] ARM: dts: rockchip: add rk3128-evb.dts
2022-10-28 14:39 ` Johan Jonker
(?)
@ 2022-10-28 14:41 ` Johan Jonker
-1 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add rk3128-evb.dts
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
---
Changed V2:
use generic node names
remove underscores in node names
add more aliases
sort
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3128-evb.dts | 110 +++++++++++++++++++++++++++++++
2 files changed, 111 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3128-evb.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 68ac9b360..0f26539d2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1127,6 +1127,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3066a-marsboard.dtb \
rk3066a-mk808.dtb \
rk3066a-rayeager.dtb \
+ rk3128-evb.dtb \
rk3188-bqedison2qc.dtb \
rk3188-px3-evb.dtb \
rk3188-radxarock.dtb \
diff --git a/arch/arm/boot/dts/rk3128-evb.dts b/arch/arm/boot/dts/rk3128-evb.dts
new file mode 100644
index 000000000..c529e7437
--- /dev/null
+++ b/arch/arm/boot/dts/rk3128-evb.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2017 Rockchip Electronics Co., Ltd
+ */
+
+/dts-v1/;
+
+#include "rk3128.dtsi"
+
+/ {
+ model = "Rockchip RK3128 Evaluation board";
+ compatible = "rockchip,rk3128-evb", "rockchip,rk3128";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ gpio3 = &gpio3;
+ i2c1 = &i2c1;
+ mmc0 = &emmc;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ memory@60000000 {
+ device_type = "memory";
+ reg = <0x60000000 0x40000000>;
+ };
+
+ vcc5v0_otg: vcc5v0-otg-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc5v0_otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc5v0_host";
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&emmc {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ };
+};
+
+&usb2phy {
+ status = "okay";
+};
+
+&usb2phy_host {
+ status = "okay";
+};
+
+&usb2phy_otg {
+ status = "okay";
+};
+
+&usb_host_ehci {
+ status = "okay";
+};
+
+&usb_host_ohci {
+ status = "okay";
+};
+
+&usb_otg {
+ vbus-supply = <&vcc5v0_otg>;
+ status = "okay";
+};
+
+&pinctrl {
+ usb-host {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <2 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb-otg {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <0 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 4/4] ARM: dts: rockchip: add rk3128-evb.dts
@ 2022-10-28 14:41 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add rk3128-evb.dts
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
---
Changed V2:
use generic node names
remove underscores in node names
add more aliases
sort
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3128-evb.dts | 110 +++++++++++++++++++++++++++++++
2 files changed, 111 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3128-evb.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 68ac9b360..0f26539d2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1127,6 +1127,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3066a-marsboard.dtb \
rk3066a-mk808.dtb \
rk3066a-rayeager.dtb \
+ rk3128-evb.dtb \
rk3188-bqedison2qc.dtb \
rk3188-px3-evb.dtb \
rk3188-radxarock.dtb \
diff --git a/arch/arm/boot/dts/rk3128-evb.dts b/arch/arm/boot/dts/rk3128-evb.dts
new file mode 100644
index 000000000..c529e7437
--- /dev/null
+++ b/arch/arm/boot/dts/rk3128-evb.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2017 Rockchip Electronics Co., Ltd
+ */
+
+/dts-v1/;
+
+#include "rk3128.dtsi"
+
+/ {
+ model = "Rockchip RK3128 Evaluation board";
+ compatible = "rockchip,rk3128-evb", "rockchip,rk3128";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ gpio3 = &gpio3;
+ i2c1 = &i2c1;
+ mmc0 = &emmc;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ memory@60000000 {
+ device_type = "memory";
+ reg = <0x60000000 0x40000000>;
+ };
+
+ vcc5v0_otg: vcc5v0-otg-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc5v0_otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc5v0_host";
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&emmc {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ };
+};
+
+&usb2phy {
+ status = "okay";
+};
+
+&usb2phy_host {
+ status = "okay";
+};
+
+&usb2phy_otg {
+ status = "okay";
+};
+
+&usb_host_ehci {
+ status = "okay";
+};
+
+&usb_host_ohci {
+ status = "okay";
+};
+
+&usb_otg {
+ vbus-supply = <&vcc5v0_otg>;
+ status = "okay";
+};
+
+&pinctrl {
+ usb-host {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <2 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb-otg {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <0 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
--
2.20.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 4/4] ARM: dts: rockchip: add rk3128-evb.dts
@ 2022-10-28 14:41 ` Johan Jonker
0 siblings, 0 replies; 19+ messages in thread
From: Johan Jonker @ 2022-10-28 14:41 UTC (permalink / raw)
To: kever.yang, heiko
Cc: sjg, philipp.tomsich, zhangqing, hjc, robh+dt,
krzysztof.kozlowski+dt, daniel.lezcano, tglx, arnd, olof, soc,
devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Add rk3128-evb.dts
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
---
Changed V2:
use generic node names
remove underscores in node names
add more aliases
sort
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3128-evb.dts | 110 +++++++++++++++++++++++++++++++
2 files changed, 111 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3128-evb.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 68ac9b360..0f26539d2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1127,6 +1127,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3066a-marsboard.dtb \
rk3066a-mk808.dtb \
rk3066a-rayeager.dtb \
+ rk3128-evb.dtb \
rk3188-bqedison2qc.dtb \
rk3188-px3-evb.dtb \
rk3188-radxarock.dtb \
diff --git a/arch/arm/boot/dts/rk3128-evb.dts b/arch/arm/boot/dts/rk3128-evb.dts
new file mode 100644
index 000000000..c529e7437
--- /dev/null
+++ b/arch/arm/boot/dts/rk3128-evb.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2017 Rockchip Electronics Co., Ltd
+ */
+
+/dts-v1/;
+
+#include "rk3128.dtsi"
+
+/ {
+ model = "Rockchip RK3128 Evaluation board";
+ compatible = "rockchip,rk3128-evb", "rockchip,rk3128";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ gpio3 = &gpio3;
+ i2c1 = &i2c1;
+ mmc0 = &emmc;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ memory@60000000 {
+ device_type = "memory";
+ reg = <0x60000000 0x40000000>;
+ };
+
+ vcc5v0_otg: vcc5v0-otg-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc5v0_otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc5v0_host";
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&emmc {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ };
+};
+
+&usb2phy {
+ status = "okay";
+};
+
+&usb2phy_host {
+ status = "okay";
+};
+
+&usb2phy_otg {
+ status = "okay";
+};
+
+&usb_host_ehci {
+ status = "okay";
+};
+
+&usb_host_ohci {
+ status = "okay";
+};
+
+&usb_otg {
+ vbus-supply = <&vcc5v0_otg>;
+ status = "okay";
+};
+
+&pinctrl {
+ usb-host {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <2 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb-otg {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <0 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [tip: timers/core] dt-bindings: timer: rockchip: Add rockchip,rk3128-timer
2022-10-28 14:41 ` Johan Jonker
(?)
(?)
@ 2022-12-09 15:47 ` tip-bot2 for Johan Jonker
-1 siblings, 0 replies; 19+ messages in thread
From: tip-bot2 for Johan Jonker @ 2022-12-09 15:47 UTC (permalink / raw)
To: linux-tip-commits
Cc: Johan Jonker, Krzysztof Kozlowski, Heiko Stuebner,
Daniel Lezcano, x86, linux-kernel
The following commit has been merged into the timers/core branch of tip:
Commit-ID: 9ffa5e6b8f93ccf1a217dd12e204c1a5e211abef
Gitweb: https://git.kernel.org/tip/9ffa5e6b8f93ccf1a217dd12e204c1a5e211abef
Author: Johan Jonker <jbx6244@gmail.com>
AuthorDate: Fri, 28 Oct 2022 16:41:30 +02:00
Committer: Daniel Lezcano <daniel.lezcano@kernel.org>
CommitterDate: Fri, 02 Dec 2022 12:48:27 +01:00
dt-bindings: timer: rockchip: Add rockchip,rk3128-timer
Add rockchip,rk3128-timer compatible string.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
Link: https://lore.kernel.org/r/0e57f38f-bace-8556-7258-aa0b3c0ac103@gmail.com
---
Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
index dc3bc1e..b61ed1a 100644
--- a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
@@ -18,6 +18,7 @@ properties:
- enum:
- rockchip,rv1108-timer
- rockchip,rk3036-timer
+ - rockchip,rk3128-timer
- rockchip,rk3188-timer
- rockchip,rk3228-timer
- rockchip,rk3229-timer
^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: (subset) [PATCH v2 0/4] Add basic Rockchip rk3128 DT support
2022-10-28 14:39 ` Johan Jonker
(?)
@ 2022-12-14 14:26 ` Heiko Stuebner
-1 siblings, 0 replies; 19+ messages in thread
From: Heiko Stuebner @ 2022-12-14 14:26 UTC (permalink / raw)
To: Johan Jonker, kever.yang
Cc: Heiko Stuebner, devicetree, robh+dt, linux-arm-kernel,
linux-kernel, hjc, zhangqing, krzysztof.kozlowski+dt,
philipp.tomsich, soc, tglx, daniel.lezcano, arnd, linux-rockchip,
sjg, olof
On Fri, 28 Oct 2022 16:39:04 +0200, Johan Jonker wrote:
> Add basic Rockchip rk3128 DT support.
>
> Features:
> Quad-core ARM Cortex-A7MP Core processor
> Clock & reset unit
> Power management unit
> Interrupt controller
> DMAC
> 6x 64 bits Timers
> 4x PWMs
> 1x 32 bits watchdog
>
> [...]
Applied for 6.3, thanks!
[1/4] dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
commit: a1392d5ac60864a3682c447fe62392eb56e9d93b
[3/4] ARM: dts: rockchip: add rk3128.dtsi
commit: 9ef609cbdbf7a45599b0c9c21e9e7d2ae625896f
[4/4] ARM: dts: rockchip: add rk3128-evb.dts
commit: 7232dafab89ac23b570d0adb3402164719fcbe3d
Best regards,
--
Heiko Stuebner <heiko@sntech.de>
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: (subset) [PATCH v2 0/4] Add basic Rockchip rk3128 DT support
@ 2022-12-14 14:26 ` Heiko Stuebner
0 siblings, 0 replies; 19+ messages in thread
From: Heiko Stuebner @ 2022-12-14 14:26 UTC (permalink / raw)
To: Johan Jonker, kever.yang
Cc: Heiko Stuebner, devicetree, robh+dt, linux-arm-kernel,
linux-kernel, hjc, zhangqing, krzysztof.kozlowski+dt,
philipp.tomsich, soc, tglx, daniel.lezcano, arnd, linux-rockchip,
sjg, olof
On Fri, 28 Oct 2022 16:39:04 +0200, Johan Jonker wrote:
> Add basic Rockchip rk3128 DT support.
>
> Features:
> Quad-core ARM Cortex-A7MP Core processor
> Clock & reset unit
> Power management unit
> Interrupt controller
> DMAC
> 6x 64 bits Timers
> 4x PWMs
> 1x 32 bits watchdog
>
> [...]
Applied for 6.3, thanks!
[1/4] dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
commit: a1392d5ac60864a3682c447fe62392eb56e9d93b
[3/4] ARM: dts: rockchip: add rk3128.dtsi
commit: 9ef609cbdbf7a45599b0c9c21e9e7d2ae625896f
[4/4] ARM: dts: rockchip: add rk3128-evb.dts
commit: 7232dafab89ac23b570d0adb3402164719fcbe3d
Best regards,
--
Heiko Stuebner <heiko@sntech.de>
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: (subset) [PATCH v2 0/4] Add basic Rockchip rk3128 DT support
@ 2022-12-14 14:26 ` Heiko Stuebner
0 siblings, 0 replies; 19+ messages in thread
From: Heiko Stuebner @ 2022-12-14 14:26 UTC (permalink / raw)
To: Johan Jonker, kever.yang
Cc: Heiko Stuebner, devicetree, robh+dt, linux-arm-kernel,
linux-kernel, hjc, zhangqing, krzysztof.kozlowski+dt,
philipp.tomsich, soc, tglx, daniel.lezcano, arnd, linux-rockchip,
sjg, olof
On Fri, 28 Oct 2022 16:39:04 +0200, Johan Jonker wrote:
> Add basic Rockchip rk3128 DT support.
>
> Features:
> Quad-core ARM Cortex-A7MP Core processor
> Clock & reset unit
> Power management unit
> Interrupt controller
> DMAC
> 6x 64 bits Timers
> 4x PWMs
> 1x 32 bits watchdog
>
> [...]
Applied for 6.3, thanks!
[1/4] dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
commit: a1392d5ac60864a3682c447fe62392eb56e9d93b
[3/4] ARM: dts: rockchip: add rk3128.dtsi
commit: 9ef609cbdbf7a45599b0c9c21e9e7d2ae625896f
[4/4] ARM: dts: rockchip: add rk3128-evb.dts
commit: 7232dafab89ac23b570d0adb3402164719fcbe3d
Best regards,
--
Heiko Stuebner <heiko@sntech.de>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2022-12-14 14:28 UTC | newest]
Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-10-28 14:39 [PATCH v2 0/4] Add basic Rockchip rk3128 DT support Johan Jonker
2022-10-28 14:39 ` Johan Jonker
2022-10-28 14:39 ` Johan Jonker
2022-10-28 14:41 ` [PATCH v2 1/4] dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board Johan Jonker
2022-10-28 14:41 ` Johan Jonker
2022-10-28 14:41 ` Johan Jonker
2022-10-28 14:41 ` [PATCH v2 2/4] dt-bindings: timer: rockchip: add rockchip,rk3128-timer Johan Jonker
2022-10-28 14:41 ` Johan Jonker
2022-10-28 14:41 ` Johan Jonker
2022-12-09 15:47 ` [tip: timers/core] dt-bindings: timer: rockchip: Add rockchip,rk3128-timer tip-bot2 for Johan Jonker
2022-10-28 14:41 ` [PATCH v2 3/4] ARM: dts: rockchip: add rk3128.dtsi Johan Jonker
2022-10-28 14:41 ` Johan Jonker
2022-10-28 14:41 ` Johan Jonker
2022-10-28 14:41 ` [PATCH v2 4/4] ARM: dts: rockchip: add rk3128-evb.dts Johan Jonker
2022-10-28 14:41 ` Johan Jonker
2022-10-28 14:41 ` Johan Jonker
2022-12-14 14:26 ` (subset) [PATCH v2 0/4] Add basic Rockchip rk3128 DT support Heiko Stuebner
2022-12-14 14:26 ` Heiko Stuebner
2022-12-14 14:26 ` Heiko Stuebner
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.