[PATCH v12 1/2] thermal: loongson-2: add thermal management support

[PATCH v12 1/2] thermal: loongson-2: add thermal management support

[Yinbo Zhu]

This patch adds the support for Loongson-2 thermal sensor controller,
which can support maximum 4 sensors.

It's based on thermal of framework:
 - Trip points defined in device tree.
 - Cpufreq as cooling device registered in Loongson-2 cpufreq driver.
 - Pwm fan as cooling device registered in hwmon pwm-fan driver.

Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
---
Change in v12:
		1. Fixup it about min and max.
		2. Use dev_err_probe replace dev_err in devm_request_threaded_irq context.
Change in v11:
		1. Add min() and max() to replace related code in function
		   loongson2_thermal_set.
		2. Add dev_err_probe to to replace related code for function
		   return value use devm_thermal_of_zone_register.
		3. Replace thermal_add_hwmon_sysfs with devm_thermal_add_hwmon_sysfs
		   and use dev_warn replace dev_err in this context.
Change in v10:
		1. Add all history change log information.
Change in v9:
		1. Switch new API that use devm_thermal_of_zone_register
		   to replace previous interfaces.
		2. Add depend on LOONGARCH || COMPILE_TEST.
Change in v8:
                1. Replace string loongson2/Loongson2/LOONGSON2 with loongson-2/
                   Loongson-2/LOONGSON-2 in Kconfig and commit log and MAINTAINERS
		   files.
Change in v7:
		1. Split the modification of patch 3 and merge it into this patch.
		2. Remove the unless code annotation to fix the compile warning
		   when compile C code with W=1.
Change in v6:
		1. NO change, but other patch in this series of patches set has
		   changes.
Change in v5:
		1. NO change, but other patch in this series of patches set has
		   changes.
Change in v4:
		1. Fixup the compatible.
Change in v3:
		1. Add a function to gain sensor id an remove dts id.
Change in v2:
		1. Remove error msg printing when addr ioremap has error.
		2. Make loongson2 thermal driver was built-in by default.
		3. Replace ls2k with loongson2.
		4. Remove CONFIG_PM_SLEEP and set pm function type was
		   __maybe_unused.

 MAINTAINERS                         |   7 +
 drivers/thermal/Kconfig             |  10 ++
 drivers/thermal/Makefile            |   1 +
 drivers/thermal/loongson2_thermal.c | 260 ++++++++++++++++++++++++++++
 4 files changed, 278 insertions(+)
 create mode 100644 drivers/thermal/loongson2_thermal.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 1b391ca7cf91..0d867573fe4c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12013,6 +12013,13 @@ F:	drivers/*/*loongarch*
 F:	Documentation/loongarch/
 F:	Documentation/translations/zh_CN/loongarch/
 
+LOONGSON-2 SOC SERIES THERMAL DRIVER
+M:	zhanghongchen <zhanghongchen@loongson.cn>
+M:	Yinbo Zhu <zhuyinbo@loongson.cn>
+L:	linux-pm@vger.kernel.org
+S:	Maintained
+F:	drivers/thermal/loongson2_thermal.c
+
 LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
 M:	Sathya Prakash <sathya.prakash@broadcom.com>
 M:	Sreekanth Reddy <sreekanth.reddy@broadcom.com>
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index e052dae614eb..93d84bcb16dd 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -504,4 +504,14 @@ config KHADAS_MCU_FAN_THERMAL
 	  If you say yes here you get support for the FAN controlled
 	  by the Microcontroller found on the Khadas VIM boards.
 
+config LOONGSON2_THERMAL
+	tristate "Loongson-2 SoC series thermal driver"
+	depends on LOONGARCH || COMPILE_TEST
+	depends on OF
+	help
+	  Support for Thermal driver found on Loongson-2 SoC series platforms.
+	  It supports one critical trip point and one passive trip point. The
+	  cpufreq and the pwm fan is used as the cooling device to throttle
+	  CPUs when the passive trip is crossed.
+
 endif
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 2506c6c8ca83..02f3db809858 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -61,3 +61,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
 obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
 obj-$(CONFIG_SPRD_THERMAL)	+= sprd_thermal.o
 obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)	+= khadas_mcu_fan.o
+obj-$(CONFIG_LOONGSON2_THERMAL)	+= loongson2_thermal.o
diff --git a/drivers/thermal/loongson2_thermal.c b/drivers/thermal/loongson2_thermal.c
new file mode 100644
index 000000000000..2d495469e8dd
--- /dev/null
+++ b/drivers/thermal/loongson2_thermal.c
@@ -0,0 +1,260 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Author: zhanghongchen <zhanghongchen@loongson.cn>
+ *         Yinbo Zhu <zhuyinbo@loongson.cn>
+ * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
+ */
+
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_device.h>
+#include <linux/thermal.h>
+#include "thermal_hwmon.h"
+
+#define LOONGSON2_SOC_MAX_SENSOR_NUM			4
+
+#define LOONGSON2_TSENSOR_CTRL_HI			0x0
+#define LOONGSON2_TSENSOR_CTRL_LO			0x8
+#define LOONGSON2_TSENSOR_STATUS			0x10
+#define LOONGSON2_TSENSOR_OUT				0x14
+
+struct loongson2_thermal_data {
+	struct thermal_zone_device *tzd;
+	int irq;
+	int id;
+	void __iomem *regs;
+	struct platform_device *pdev;
+	u16 ctrl_low_val;
+	u16 ctrl_hi_val;
+};
+
+static int loongson2_thermal_set(struct loongson2_thermal_data *data,
+					int low, int high, bool enable)
+{
+	u64 reg_ctrl = 0;
+	int reg_off = data->id * 2;
+
+	if (low > high)
+		return -EINVAL;
+
+	low = max(low, -100);
+	high = min(high, 155);
+
+	low += 100;
+	high += 100;
+
+	reg_ctrl |= low;
+	reg_ctrl |= enable ? 0x100 : 0;
+	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+
+	reg_ctrl = 0;
+	reg_ctrl |= high;
+	reg_ctrl |= enable ? 0x100 : 0;
+	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+	return 0;
+}
+
+static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
+{
+	u32 reg_val;
+	struct loongson2_thermal_data *data = tz->devdata;
+
+	reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
+	*temp = ((reg_val & 0xff) - 100) * 1000;
+
+	return 0;
+}
+
+static int loongson2_thermal_get_sensor_id(void)
+{
+	int ret, id;
+	struct of_phandle_args sensor_specs;
+	struct device_node *np, *sensor_np;
+
+	np = of_find_node_by_name(NULL, "thermal-zones");
+	if (!np)
+		return -ENODEV;
+
+	sensor_np = of_get_next_child(np, NULL);
+	ret = of_parse_phandle_with_args(sensor_np, "thermal-sensors",
+			"#thermal-sensor-cells",
+			0, &sensor_specs);
+	if (ret) {
+		of_node_put(np);
+		of_node_put(sensor_np);
+		return ret;
+	}
+
+	if (sensor_specs.args_count >= 1) {
+		id = sensor_specs.args[0];
+		WARN(sensor_specs.args_count > 1,
+				"%s: too many cells in sensor specifier %d\n",
+				sensor_specs.np->name, sensor_specs.args_count);
+	} else {
+		id = 0;
+	}
+
+	of_node_put(np);
+	of_node_put(sensor_np);
+
+	return id;
+}
+
+static irqreturn_t loongson2_thermal_alarm_irq(int irq, void *dev)
+{
+	struct loongson2_thermal_data *data = dev;
+
+	/* clear interrupt */
+	writeb(0x3, data->regs + LOONGSON2_TSENSOR_STATUS);
+
+	disable_irq_nosync(irq);
+
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
+{
+	struct loongson2_thermal_data *data = dev;
+
+	thermal_zone_device_update(data->tzd,
+				   THERMAL_EVENT_UNSPECIFIED);
+	enable_irq(data->irq);
+
+	return IRQ_HANDLED;
+}
+
+static int loongson2_thermal_set_trips(struct thermal_zone_device *tz, int low, int high)
+{
+	struct loongson2_thermal_data *data = tz->devdata;
+
+	return loongson2_thermal_set(data, low/1000, high/1000, true);
+}
+
+static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
+	.get_temp = loongson2_thermal_get_temp,
+	.set_trips = loongson2_thermal_set_trips,
+};
+
+static int loongson2_thermal_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct loongson2_thermal_data *data;
+	int ret;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->pdev = pdev;
+	platform_set_drvdata(pdev, data);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	data->regs = devm_ioremap(dev, res->start, resource_size(res));
+	if (IS_ERR(data->regs))
+		return PTR_ERR(data->regs);
+
+	/* get irq */
+	data->irq = platform_get_irq(pdev, 0);
+	if (data->irq < 0)
+		return data->irq;
+
+	/* get id */
+	data->id = loongson2_thermal_get_sensor_id();
+	if (data->id > LOONGSON2_SOC_MAX_SENSOR_NUM - 1 || data->id < 0) {
+		dev_err(dev, "sensor id error,must be in <0 ~ %d>\n",
+				LOONGSON2_SOC_MAX_SENSOR_NUM - 1);
+		return -EINVAL;
+	}
+
+	writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
+
+	loongson2_thermal_set(data, 0, 0, false);
+
+	data->tzd = devm_thermal_of_zone_register(&pdev->dev, data->id, data,
+			&loongson2_of_thermal_ops);
+	if (IS_ERR(data->tzd))
+		return dev_err_probe(&pdev->dev, PTR_ERR(data->tzd),
+				"failed to register");
+
+	ret = devm_request_threaded_irq(dev, data->irq,
+			loongson2_thermal_alarm_irq, loongson2_thermal_irq_thread,
+			IRQF_ONESHOT, "loongson2_thermal", data);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "failed to request alarm irq\n");
+
+	/*
+	 * Thermal_zone doesn't enable hwmon as default,
+	 * enable it here
+	 */
+	data->tzd->tzp->no_hwmon = false;
+	if (devm_thermal_add_hwmon_sysfs(data->tzd))
+		dev_warn(&pdev->dev, "Failed to add hwmon sysfs attributes\n");
+
+	return 0;
+}
+
+static int loongson2_thermal_remove(struct platform_device *pdev)
+{
+	struct loongson2_thermal_data *data = platform_get_drvdata(pdev);
+	int reg_off = data->id * 2;
+
+	/* disable interrupt */
+	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+	return 0;
+}
+
+static const struct of_device_id of_loongson2_thermal_match[] = {
+	{ .compatible = "loongson,ls2k-thermal",},
+	{ /* end */ }
+};
+MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
+
+static int __maybe_unused loongson2_thermal_suspend(struct device *dev)
+{
+	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
+	int reg_off = data->id * 2;
+
+	data->ctrl_low_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+	data->ctrl_hi_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+	return 0;
+}
+
+static int __maybe_unused loongson2_thermal_resume(struct device *dev)
+{
+	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
+	int reg_off = data->id * 2;
+
+	writew(data->ctrl_low_val, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+	writew(data->ctrl_hi_val, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(loongson2_thermal_pm_ops,
+			 loongson2_thermal_suspend, loongson2_thermal_resume);
+
+static struct platform_driver loongson2_thermal_driver = {
+	.driver = {
+		.name		= "loongson2_thermal",
+		.pm = &loongson2_thermal_pm_ops,
+		.of_match_table = of_loongson2_thermal_match,
+	},
+	.probe	= loongson2_thermal_probe,
+	.remove	= loongson2_thermal_remove,
+};
+module_platform_driver(loongson2_thermal_driver);
+
+MODULE_DESCRIPTION("Loongson2 thermal driver");
+MODULE_LICENSE("GPL");
-- 
2.31.1

[PATCH v12 2/2] dt-bindings: thermal: add loongson-2 thermal

[Yinbo Zhu]

Add the Loongson-2 thermal binding with DT schema format using
json-schema.

Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Change in v12:
		1. NO change, but other patch in this series of patches set
		   has changes.
Change in v11:
		1. NO change, but other patch in this series of patches set
		   has changes.
Change in v10:
		1. Add all history change log information.
Change in v9:
		1. NO change, but other patch in this series of patches set
		   has changes.
Change in v8:
                1. Replace string Loongson2/loongson2 with Loongson-2/loongson-2.
Change in v7:
		1. Split the modification of patch 3 and merge it into this patch.
Change in v6:
		1. Fix the warning "reg: [[0, 534779136], [0, 48]] is too long"
		   when compile the yaml.
Change in v5:
		1. Keep use same quotes "'" in all places. 
Change in v4:
		1. Fixup the compatible.
		2. Update the binding file name.
		3. Include irq.h to fix compile issue.
Change in v3:
		1. Remove the sensor id.
		2. Remove the interrupt-parent in thermal required property.
		3. Update the thermal binding file name.
		4. Fixup the commit log information.
Change in v2:
		1. Add description and type about the "id".	
		2. Make the filename was based on compatible.

 .../thermal/loongson,ls2k-thermal.yaml        | 43 +++++++++++++++++++
 MAINTAINERS                                   |  1 +
 2 files changed, 44 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml

diff --git a/Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml b/Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml
new file mode 100644
index 000000000000..c0637e2d6d57
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/loongson,ls2k-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Thermal sensors on Loongson-2 SoCs
+
+maintainers:
+  - zhanghongchen <zhanghongchen@loongson.cn>
+  - Yinbo Zhu <zhuyinbo@loongson.cn>
+
+properties:
+  compatible:
+    const: loongson,ls2k-thermal
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  '#thermal-sensor-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - '#thermal-sensor-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    thermal: thermal-sensor@1fe01500 {
+        compatible = "loongson,ls2k-thermal";
+        reg = <0x1fe01500 0x30>;
+        interrupt-parent = <&liointc0>;
+        interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+        #thermal-sensor-cells = <1>;
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 0d867573fe4c..182129c73ed5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12018,6 +12018,7 @@ M:	zhanghongchen <zhanghongchen@loongson.cn>
 M:	Yinbo Zhu <zhuyinbo@loongson.cn>
 L:	linux-pm@vger.kernel.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml
 F:	drivers/thermal/loongson2_thermal.c
 
 LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
-- 
2.31.1

Re: [PATCH v12 1/2] thermal: loongson-2: add thermal management support

[Yinbo Zhu]

Hi Maintainer,

Could you help me merge my patch?

Thanks
Yinbo.
在 2022/11/14 上午10:47, Yinbo Zhu 写道:
> This patch adds the support for Loongson-2 thermal sensor controller,
> which can support maximum 4 sensors.
> 
> It's based on thermal of framework:
>   - Trip points defined in device tree.
>   - Cpufreq as cooling device registered in Loongson-2 cpufreq driver.
>   - Pwm fan as cooling device registered in hwmon pwm-fan driver.
> 
> Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
> Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
> ---
> Change in v12:
> 		1. Fixup it about min and max.
> 		2. Use dev_err_probe replace dev_err in devm_request_threaded_irq context.
> Change in v11:
> 		1. Add min() and max() to replace related code in function
> 		   loongson2_thermal_set.
> 		2. Add dev_err_probe to to replace related code for function
> 		   return value use devm_thermal_of_zone_register.
> 		3. Replace thermal_add_hwmon_sysfs with devm_thermal_add_hwmon_sysfs
> 		   and use dev_warn replace dev_err in this context.
> Change in v10:
> 		1. Add all history change log information.
> Change in v9:
> 		1. Switch new API that use devm_thermal_of_zone_register
> 		   to replace previous interfaces.
> 		2. Add depend on LOONGARCH || COMPILE_TEST.
> Change in v8:
>                  1. Replace string loongson2/Loongson2/LOONGSON2 with loongson-2/
>                     Loongson-2/LOONGSON-2 in Kconfig and commit log and MAINTAINERS
> 		   files.
> Change in v7:
> 		1. Split the modification of patch 3 and merge it into this patch.
> 		2. Remove the unless code annotation to fix the compile warning
> 		   when compile C code with W=1.
> Change in v6:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v5:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v4:
> 		1. Fixup the compatible.
> Change in v3:
> 		1. Add a function to gain sensor id an remove dts id.
> Change in v2:
> 		1. Remove error msg printing when addr ioremap has error.
> 		2. Make loongson2 thermal driver was built-in by default.
> 		3. Replace ls2k with loongson2.
> 		4. Remove CONFIG_PM_SLEEP and set pm function type was
> 		   __maybe_unused.
> 
>   MAINTAINERS                         |   7 +
>   drivers/thermal/Kconfig             |  10 ++
>   drivers/thermal/Makefile            |   1 +
>   drivers/thermal/loongson2_thermal.c | 260 ++++++++++++++++++++++++++++
>   4 files changed, 278 insertions(+)
>   create mode 100644 drivers/thermal/loongson2_thermal.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 1b391ca7cf91..0d867573fe4c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12013,6 +12013,13 @@ F:	drivers/*/*loongarch*
>   F:	Documentation/loongarch/
>   F:	Documentation/translations/zh_CN/loongarch/
>   
> +LOONGSON-2 SOC SERIES THERMAL DRIVER
> +M:	zhanghongchen <zhanghongchen@loongson.cn>
> +M:	Yinbo Zhu <zhuyinbo@loongson.cn>
> +L:	linux-pm@vger.kernel.org
> +S:	Maintained
> +F:	drivers/thermal/loongson2_thermal.c
> +
>   LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
>   M:	Sathya Prakash <sathya.prakash@broadcom.com>
>   M:	Sreekanth Reddy <sreekanth.reddy@broadcom.com>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index e052dae614eb..93d84bcb16dd 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -504,4 +504,14 @@ config KHADAS_MCU_FAN_THERMAL
>   	  If you say yes here you get support for the FAN controlled
>   	  by the Microcontroller found on the Khadas VIM boards.
>   
> +config LOONGSON2_THERMAL
> +	tristate "Loongson-2 SoC series thermal driver"
> +	depends on LOONGARCH || COMPILE_TEST
> +	depends on OF
> +	help
> +	  Support for Thermal driver found on Loongson-2 SoC series platforms.
> +	  It supports one critical trip point and one passive trip point. The
> +	  cpufreq and the pwm fan is used as the cooling device to throttle
> +	  CPUs when the passive trip is crossed.
> +
>   endif
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 2506c6c8ca83..02f3db809858 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -61,3 +61,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
>   obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
>   obj-$(CONFIG_SPRD_THERMAL)	+= sprd_thermal.o
>   obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)	+= khadas_mcu_fan.o
> +obj-$(CONFIG_LOONGSON2_THERMAL)	+= loongson2_thermal.o
> diff --git a/drivers/thermal/loongson2_thermal.c b/drivers/thermal/loongson2_thermal.c
> new file mode 100644
> index 000000000000..2d495469e8dd
> --- /dev/null
> +++ b/drivers/thermal/loongson2_thermal.c
> @@ -0,0 +1,260 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Author: zhanghongchen <zhanghongchen@loongson.cn>
> + *         Yinbo Zhu <zhuyinbo@loongson.cn>
> + * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
> + */
> +
> +#include <linux/cpufreq.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/of_device.h>
> +#include <linux/thermal.h>
> +#include "thermal_hwmon.h"
> +
> +#define LOONGSON2_SOC_MAX_SENSOR_NUM			4
> +
> +#define LOONGSON2_TSENSOR_CTRL_HI			0x0
> +#define LOONGSON2_TSENSOR_CTRL_LO			0x8
> +#define LOONGSON2_TSENSOR_STATUS			0x10
> +#define LOONGSON2_TSENSOR_OUT				0x14
> +
> +struct loongson2_thermal_data {
> +	struct thermal_zone_device *tzd;
> +	int irq;
> +	int id;
> +	void __iomem *regs;
> +	struct platform_device *pdev;
> +	u16 ctrl_low_val;
> +	u16 ctrl_hi_val;
> +};
> +
> +static int loongson2_thermal_set(struct loongson2_thermal_data *data,
> +					int low, int high, bool enable)
> +{
> +	u64 reg_ctrl = 0;
> +	int reg_off = data->id * 2;
> +
> +	if (low > high)
> +		return -EINVAL;
> +
> +	low = max(low, -100);
> +	high = min(high, 155);
> +
> +	low += 100;
> +	high += 100;
> +
> +	reg_ctrl |= low;
> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +
> +	reg_ctrl = 0;
> +	reg_ctrl |= high;
> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
> +{
> +	u32 reg_val;
> +	struct loongson2_thermal_data *data = tz->devdata;
> +
> +	reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
> +	*temp = ((reg_val & 0xff) - 100) * 1000;
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_get_sensor_id(void)
> +{
> +	int ret, id;
> +	struct of_phandle_args sensor_specs;
> +	struct device_node *np, *sensor_np;
> +
> +	np = of_find_node_by_name(NULL, "thermal-zones");
> +	if (!np)
> +		return -ENODEV;
> +
> +	sensor_np = of_get_next_child(np, NULL);
> +	ret = of_parse_phandle_with_args(sensor_np, "thermal-sensors",
> +			"#thermal-sensor-cells",
> +			0, &sensor_specs);
> +	if (ret) {
> +		of_node_put(np);
> +		of_node_put(sensor_np);
> +		return ret;
> +	}
> +
> +	if (sensor_specs.args_count >= 1) {
> +		id = sensor_specs.args[0];
> +		WARN(sensor_specs.args_count > 1,
> +				"%s: too many cells in sensor specifier %d\n",
> +				sensor_specs.np->name, sensor_specs.args_count);
> +	} else {
> +		id = 0;
> +	}
> +
> +	of_node_put(np);
> +	of_node_put(sensor_np);
> +
> +	return id;
> +}
> +
> +static irqreturn_t loongson2_thermal_alarm_irq(int irq, void *dev)
> +{
> +	struct loongson2_thermal_data *data = dev;
> +
> +	/* clear interrupt */
> +	writeb(0x3, data->regs + LOONGSON2_TSENSOR_STATUS);
> +
> +	disable_irq_nosync(irq);
> +
> +	return IRQ_WAKE_THREAD;
> +}
> +
> +static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
> +{
> +	struct loongson2_thermal_data *data = dev;
> +
> +	thermal_zone_device_update(data->tzd,
> +				   THERMAL_EVENT_UNSPECIFIED);
> +	enable_irq(data->irq);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int loongson2_thermal_set_trips(struct thermal_zone_device *tz, int low, int high)
> +{
> +	struct loongson2_thermal_data *data = tz->devdata;
> +
> +	return loongson2_thermal_set(data, low/1000, high/1000, true);
> +}
> +
> +static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
> +	.get_temp = loongson2_thermal_get_temp,
> +	.set_trips = loongson2_thermal_set_trips,
> +};
> +
> +static int loongson2_thermal_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	struct loongson2_thermal_data *data;
> +	int ret;
> +
> +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> +	if (!data)
> +		return -ENOMEM;
> +
> +	data->pdev = pdev;
> +	platform_set_drvdata(pdev, data);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	data->regs = devm_ioremap(dev, res->start, resource_size(res));
> +	if (IS_ERR(data->regs))
> +		return PTR_ERR(data->regs);
> +
> +	/* get irq */
> +	data->irq = platform_get_irq(pdev, 0);
> +	if (data->irq < 0)
> +		return data->irq;
> +
> +	/* get id */
> +	data->id = loongson2_thermal_get_sensor_id();
> +	if (data->id > LOONGSON2_SOC_MAX_SENSOR_NUM - 1 || data->id < 0) {
> +		dev_err(dev, "sensor id error,must be in <0 ~ %d>\n",
> +				LOONGSON2_SOC_MAX_SENSOR_NUM - 1);
> +		return -EINVAL;
> +	}
> +
> +	writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
> +
> +	loongson2_thermal_set(data, 0, 0, false);
> +
> +	data->tzd = devm_thermal_of_zone_register(&pdev->dev, data->id, data,
> +			&loongson2_of_thermal_ops);
> +	if (IS_ERR(data->tzd))
> +		return dev_err_probe(&pdev->dev, PTR_ERR(data->tzd),
> +				"failed to register");
> +
> +	ret = devm_request_threaded_irq(dev, data->irq,
> +			loongson2_thermal_alarm_irq, loongson2_thermal_irq_thread,
> +			IRQF_ONESHOT, "loongson2_thermal", data);
> +	if (ret < 0)
> +		return dev_err_probe(dev, ret, "failed to request alarm irq\n");
> +
> +	/*
> +	 * Thermal_zone doesn't enable hwmon as default,
> +	 * enable it here
> +	 */
> +	data->tzd->tzp->no_hwmon = false;
> +	if (devm_thermal_add_hwmon_sysfs(data->tzd))
> +		dev_warn(&pdev->dev, "Failed to add hwmon sysfs attributes\n");
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_remove(struct platform_device *pdev)
> +{
> +	struct loongson2_thermal_data *data = platform_get_drvdata(pdev);
> +	int reg_off = data->id * 2;
> +
> +	/* disable interrupt */
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id of_loongson2_thermal_match[] = {
> +	{ .compatible = "loongson,ls2k-thermal",},
> +	{ /* end */ }
> +};
> +MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
> +
> +static int __maybe_unused loongson2_thermal_suspend(struct device *dev)
> +{
> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
> +	int reg_off = data->id * 2;
> +
> +	data->ctrl_low_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	data->ctrl_hi_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused loongson2_thermal_resume(struct device *dev)
> +{
> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
> +	int reg_off = data->id * 2;
> +
> +	writew(data->ctrl_low_val, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(data->ctrl_hi_val, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(loongson2_thermal_pm_ops,
> +			 loongson2_thermal_suspend, loongson2_thermal_resume);
> +
> +static struct platform_driver loongson2_thermal_driver = {
> +	.driver = {
> +		.name		= "loongson2_thermal",
> +		.pm = &loongson2_thermal_pm_ops,
> +		.of_match_table = of_loongson2_thermal_match,
> +	},
> +	.probe	= loongson2_thermal_probe,
> +	.remove	= loongson2_thermal_remove,
> +};
> +module_platform_driver(loongson2_thermal_driver);
> +
> +MODULE_DESCRIPTION("Loongson2 thermal driver");
> +MODULE_LICENSE("GPL");
> 

Re: [PATCH v12 2/2] dt-bindings: thermal: add loongson-2 thermal

[Yinbo Zhu]

Hi Maintainer,

Could you help me merge my patch?

Thanks,
Yinbo.

在 2022/11/14 上午10:47, Yinbo Zhu 写道:
> Add the Loongson-2 thermal binding with DT schema format using
> json-schema.
> 
> Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> Change in v12:
> 		1. NO change, but other patch in this series of patches set
> 		   has changes.
> Change in v11:
> 		1. NO change, but other patch in this series of patches set
> 		   has changes.
> Change in v10:
> 		1. Add all history change log information.
> Change in v9:
> 		1. NO change, but other patch in this series of patches set
> 		   has changes.
> Change in v8:
>                  1. Replace string Loongson2/loongson2 with Loongson-2/loongson-2.
> Change in v7:
> 		1. Split the modification of patch 3 and merge it into this patch.
> Change in v6:
> 		1. Fix the warning "reg: [[0, 534779136], [0, 48]] is too long"
> 		   when compile the yaml.
> Change in v5:
> 		1. Keep use same quotes "'" in all places.
> Change in v4:
> 		1. Fixup the compatible.
> 		2. Update the binding file name.
> 		3. Include irq.h to fix compile issue.
> Change in v3:
> 		1. Remove the sensor id.
> 		2. Remove the interrupt-parent in thermal required property.
> 		3. Update the thermal binding file name.
> 		4. Fixup the commit log information.
> Change in v2:
> 		1. Add description and type about the "id".	
> 		2. Make the filename was based on compatible.
> 
>   .../thermal/loongson,ls2k-thermal.yaml        | 43 +++++++++++++++++++
>   MAINTAINERS                                   |  1 +
>   2 files changed, 44 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml
> 
> diff --git a/Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml b/Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml
> new file mode 100644
> index 000000000000..c0637e2d6d57
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml
> @@ -0,0 +1,43 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/thermal/loongson,ls2k-thermal.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Thermal sensors on Loongson-2 SoCs
> +
> +maintainers:
> +  - zhanghongchen <zhanghongchen@loongson.cn>
> +  - Yinbo Zhu <zhuyinbo@loongson.cn>
> +
> +properties:
> +  compatible:
> +    const: loongson,ls2k-thermal
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  '#thermal-sensor-cells':
> +    const: 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - '#thermal-sensor-cells'
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    thermal: thermal-sensor@1fe01500 {
> +        compatible = "loongson,ls2k-thermal";
> +        reg = <0x1fe01500 0x30>;
> +        interrupt-parent = <&liointc0>;
> +        interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +        #thermal-sensor-cells = <1>;
> +    };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 0d867573fe4c..182129c73ed5 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12018,6 +12018,7 @@ M:	zhanghongchen <zhanghongchen@loongson.cn>
>   M:	Yinbo Zhu <zhuyinbo@loongson.cn>
>   L:	linux-pm@vger.kernel.org
>   S:	Maintained
> +F:	Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml
>   F:	drivers/thermal/loongson2_thermal.c
>   
>   LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
> 

Re: [PATCH v12 1/2] thermal: loongson-2: add thermal management support

[Yinbo Zhu]

Hi thermal maintainer,


Could you help me merge this series patch.


Thanks.

在 2022/11/14 10:47, Yinbo Zhu 写道:
> This patch adds the support for Loongson-2 thermal sensor controller,
> which can support maximum 4 sensors.
>
> It's based on thermal of framework:
>   - Trip points defined in device tree.
>   - Cpufreq as cooling device registered in Loongson-2 cpufreq driver.
>   - Pwm fan as cooling device registered in hwmon pwm-fan driver.
>
> Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
> Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
> ---
> Change in v12:
> 		1. Fixup it about min and max.
> 		2. Use dev_err_probe replace dev_err in devm_request_threaded_irq context.
> Change in v11:
> 		1. Add min() and max() to replace related code in function
> 		   loongson2_thermal_set.
> 		2. Add dev_err_probe to to replace related code for function
> 		   return value use devm_thermal_of_zone_register.
> 		3. Replace thermal_add_hwmon_sysfs with devm_thermal_add_hwmon_sysfs
> 		   and use dev_warn replace dev_err in this context.
> Change in v10:
> 		1. Add all history change log information.
> Change in v9:
> 		1. Switch new API that use devm_thermal_of_zone_register
> 		   to replace previous interfaces.
> 		2. Add depend on LOONGARCH || COMPILE_TEST.
> Change in v8:
>                  1. Replace string loongson2/Loongson2/LOONGSON2 with loongson-2/
>                     Loongson-2/LOONGSON-2 in Kconfig and commit log and MAINTAINERS
> 		   files.
> Change in v7:
> 		1. Split the modification of patch 3 and merge it into this patch.
> 		2. Remove the unless code annotation to fix the compile warning
> 		   when compile C code with W=1.
> Change in v6:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v5:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v4:
> 		1. Fixup the compatible.
> Change in v3:
> 		1. Add a function to gain sensor id an remove dts id.
> Change in v2:
> 		1. Remove error msg printing when addr ioremap has error.
> 		2. Make loongson2 thermal driver was built-in by default.
> 		3. Replace ls2k with loongson2.
> 		4. Remove CONFIG_PM_SLEEP and set pm function type was
> 		   __maybe_unused.
>
>   MAINTAINERS                         |   7 +
>   drivers/thermal/Kconfig             |  10 ++
>   drivers/thermal/Makefile            |   1 +
>   drivers/thermal/loongson2_thermal.c | 260 ++++++++++++++++++++++++++++
>   4 files changed, 278 insertions(+)
>   create mode 100644 drivers/thermal/loongson2_thermal.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 1b391ca7cf91..0d867573fe4c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12013,6 +12013,13 @@ F:	drivers/*/*loongarch*
>   F:	Documentation/loongarch/
>   F:	Documentation/translations/zh_CN/loongarch/
>   
> +LOONGSON-2 SOC SERIES THERMAL DRIVER
> +M:	zhanghongchen <zhanghongchen@loongson.cn>
> +M:	Yinbo Zhu <zhuyinbo@loongson.cn>
> +L:	linux-pm@vger.kernel.org
> +S:	Maintained
> +F:	drivers/thermal/loongson2_thermal.c
> +
>   LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
>   M:	Sathya Prakash <sathya.prakash@broadcom.com>
>   M:	Sreekanth Reddy <sreekanth.reddy@broadcom.com>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index e052dae614eb..93d84bcb16dd 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -504,4 +504,14 @@ config KHADAS_MCU_FAN_THERMAL
>   	  If you say yes here you get support for the FAN controlled
>   	  by the Microcontroller found on the Khadas VIM boards.
>   
> +config LOONGSON2_THERMAL
> +	tristate "Loongson-2 SoC series thermal driver"
> +	depends on LOONGARCH || COMPILE_TEST
> +	depends on OF
> +	help
> +	  Support for Thermal driver found on Loongson-2 SoC series platforms.
> +	  It supports one critical trip point and one passive trip point. The
> +	  cpufreq and the pwm fan is used as the cooling device to throttle
> +	  CPUs when the passive trip is crossed.
> +
>   endif
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 2506c6c8ca83..02f3db809858 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -61,3 +61,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
>   obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
>   obj-$(CONFIG_SPRD_THERMAL)	+= sprd_thermal.o
>   obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)	+= khadas_mcu_fan.o
> +obj-$(CONFIG_LOONGSON2_THERMAL)	+= loongson2_thermal.o
> diff --git a/drivers/thermal/loongson2_thermal.c b/drivers/thermal/loongson2_thermal.c
> new file mode 100644
> index 000000000000..2d495469e8dd
> --- /dev/null
> +++ b/drivers/thermal/loongson2_thermal.c
> @@ -0,0 +1,260 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Author: zhanghongchen <zhanghongchen@loongson.cn>
> + *         Yinbo Zhu <zhuyinbo@loongson.cn>
> + * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
> + */
> +
> +#include <linux/cpufreq.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/of_device.h>
> +#include <linux/thermal.h>
> +#include "thermal_hwmon.h"
> +
> +#define LOONGSON2_SOC_MAX_SENSOR_NUM			4
> +
> +#define LOONGSON2_TSENSOR_CTRL_HI			0x0
> +#define LOONGSON2_TSENSOR_CTRL_LO			0x8
> +#define LOONGSON2_TSENSOR_STATUS			0x10
> +#define LOONGSON2_TSENSOR_OUT				0x14
> +
> +struct loongson2_thermal_data {
> +	struct thermal_zone_device *tzd;
> +	int irq;
> +	int id;
> +	void __iomem *regs;
> +	struct platform_device *pdev;
> +	u16 ctrl_low_val;
> +	u16 ctrl_hi_val;
> +};
> +
> +static int loongson2_thermal_set(struct loongson2_thermal_data *data,
> +					int low, int high, bool enable)
> +{
> +	u64 reg_ctrl = 0;
> +	int reg_off = data->id * 2;
> +
> +	if (low > high)
> +		return -EINVAL;
> +
> +	low = max(low, -100);
> +	high = min(high, 155);
> +
> +	low += 100;
> +	high += 100;
> +
> +	reg_ctrl |= low;
> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +
> +	reg_ctrl = 0;
> +	reg_ctrl |= high;
> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
> +{
> +	u32 reg_val;
> +	struct loongson2_thermal_data *data = tz->devdata;
> +
> +	reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
> +	*temp = ((reg_val & 0xff) - 100) * 1000;
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_get_sensor_id(void)
> +{
> +	int ret, id;
> +	struct of_phandle_args sensor_specs;
> +	struct device_node *np, *sensor_np;
> +
> +	np = of_find_node_by_name(NULL, "thermal-zones");
> +	if (!np)
> +		return -ENODEV;
> +
> +	sensor_np = of_get_next_child(np, NULL);
> +	ret = of_parse_phandle_with_args(sensor_np, "thermal-sensors",
> +			"#thermal-sensor-cells",
> +			0, &sensor_specs);
> +	if (ret) {
> +		of_node_put(np);
> +		of_node_put(sensor_np);
> +		return ret;
> +	}
> +
> +	if (sensor_specs.args_count >= 1) {
> +		id = sensor_specs.args[0];
> +		WARN(sensor_specs.args_count > 1,
> +				"%s: too many cells in sensor specifier %d\n",
> +				sensor_specs.np->name, sensor_specs.args_count);
> +	} else {
> +		id = 0;
> +	}
> +
> +	of_node_put(np);
> +	of_node_put(sensor_np);
> +
> +	return id;
> +}
> +
> +static irqreturn_t loongson2_thermal_alarm_irq(int irq, void *dev)
> +{
> +	struct loongson2_thermal_data *data = dev;
> +
> +	/* clear interrupt */
> +	writeb(0x3, data->regs + LOONGSON2_TSENSOR_STATUS);
> +
> +	disable_irq_nosync(irq);
> +
> +	return IRQ_WAKE_THREAD;
> +}
> +
> +static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
> +{
> +	struct loongson2_thermal_data *data = dev;
> +
> +	thermal_zone_device_update(data->tzd,
> +				   THERMAL_EVENT_UNSPECIFIED);
> +	enable_irq(data->irq);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int loongson2_thermal_set_trips(struct thermal_zone_device *tz, int low, int high)
> +{
> +	struct loongson2_thermal_data *data = tz->devdata;
> +
> +	return loongson2_thermal_set(data, low/1000, high/1000, true);
> +}
> +
> +static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
> +	.get_temp = loongson2_thermal_get_temp,
> +	.set_trips = loongson2_thermal_set_trips,
> +};
> +
> +static int loongson2_thermal_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	struct loongson2_thermal_data *data;
> +	int ret;
> +
> +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> +	if (!data)
> +		return -ENOMEM;
> +
> +	data->pdev = pdev;
> +	platform_set_drvdata(pdev, data);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	data->regs = devm_ioremap(dev, res->start, resource_size(res));
> +	if (IS_ERR(data->regs))
> +		return PTR_ERR(data->regs);
> +
> +	/* get irq */
> +	data->irq = platform_get_irq(pdev, 0);
> +	if (data->irq < 0)
> +		return data->irq;
> +
> +	/* get id */
> +	data->id = loongson2_thermal_get_sensor_id();
> +	if (data->id > LOONGSON2_SOC_MAX_SENSOR_NUM - 1 || data->id < 0) {
> +		dev_err(dev, "sensor id error,must be in <0 ~ %d>\n",
> +				LOONGSON2_SOC_MAX_SENSOR_NUM - 1);
> +		return -EINVAL;
> +	}
> +
> +	writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
> +
> +	loongson2_thermal_set(data, 0, 0, false);
> +
> +	data->tzd = devm_thermal_of_zone_register(&pdev->dev, data->id, data,
> +			&loongson2_of_thermal_ops);
> +	if (IS_ERR(data->tzd))
> +		return dev_err_probe(&pdev->dev, PTR_ERR(data->tzd),
> +				"failed to register");
> +
> +	ret = devm_request_threaded_irq(dev, data->irq,
> +			loongson2_thermal_alarm_irq, loongson2_thermal_irq_thread,
> +			IRQF_ONESHOT, "loongson2_thermal", data);
> +	if (ret < 0)
> +		return dev_err_probe(dev, ret, "failed to request alarm irq\n");
> +
> +	/*
> +	 * Thermal_zone doesn't enable hwmon as default,
> +	 * enable it here
> +	 */
> +	data->tzd->tzp->no_hwmon = false;
> +	if (devm_thermal_add_hwmon_sysfs(data->tzd))
> +		dev_warn(&pdev->dev, "Failed to add hwmon sysfs attributes\n");
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_remove(struct platform_device *pdev)
> +{
> +	struct loongson2_thermal_data *data = platform_get_drvdata(pdev);
> +	int reg_off = data->id * 2;
> +
> +	/* disable interrupt */
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id of_loongson2_thermal_match[] = {
> +	{ .compatible = "loongson,ls2k-thermal",},
> +	{ /* end */ }
> +};
> +MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
> +
> +static int __maybe_unused loongson2_thermal_suspend(struct device *dev)
> +{
> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
> +	int reg_off = data->id * 2;
> +
> +	data->ctrl_low_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	data->ctrl_hi_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused loongson2_thermal_resume(struct device *dev)
> +{
> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
> +	int reg_off = data->id * 2;
> +
> +	writew(data->ctrl_low_val, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(data->ctrl_hi_val, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(loongson2_thermal_pm_ops,
> +			 loongson2_thermal_suspend, loongson2_thermal_resume);
> +
> +static struct platform_driver loongson2_thermal_driver = {
> +	.driver = {
> +		.name		= "loongson2_thermal",
> +		.pm = &loongson2_thermal_pm_ops,
> +		.of_match_table = of_loongson2_thermal_match,
> +	},
> +	.probe	= loongson2_thermal_probe,
> +	.remove	= loongson2_thermal_remove,
> +};
> +module_platform_driver(loongson2_thermal_driver);
> +
> +MODULE_DESCRIPTION("Loongson2 thermal driver");
> +MODULE_LICENSE("GPL");

Re: [PATCH v12 1/2] thermal: loongson-2: add thermal management support

[zhuyinbo]

Friendly ping ?


在 2022/11/14 上午10:47, Yinbo Zhu 写道:
> This patch adds the support for Loongson-2 thermal sensor controller,
> which can support maximum 4 sensors.
>
> It's based on thermal of framework:
>   - Trip points defined in device tree.
>   - Cpufreq as cooling device registered in Loongson-2 cpufreq driver.
>   - Pwm fan as cooling device registered in hwmon pwm-fan driver.
>
> Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
> Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
> ---
> Change in v12:
> 		1. Fixup it about min and max.
> 		2. Use dev_err_probe replace dev_err in devm_request_threaded_irq context.
> Change in v11:
> 		1. Add min() and max() to replace related code in function
> 		   loongson2_thermal_set.
> 		2. Add dev_err_probe to to replace related code for function
> 		   return value use devm_thermal_of_zone_register.
> 		3. Replace thermal_add_hwmon_sysfs with devm_thermal_add_hwmon_sysfs
> 		   and use dev_warn replace dev_err in this context.
> Change in v10:
> 		1. Add all history change log information.
> Change in v9:
> 		1. Switch new API that use devm_thermal_of_zone_register
> 		   to replace previous interfaces.
> 		2. Add depend on LOONGARCH || COMPILE_TEST.
> Change in v8:
>                  1. Replace string loongson2/Loongson2/LOONGSON2 with loongson-2/
>                     Loongson-2/LOONGSON-2 in Kconfig and commit log and MAINTAINERS
> 		   files.
> Change in v7:
> 		1. Split the modification of patch 3 and merge it into this patch.
> 		2. Remove the unless code annotation to fix the compile warning
> 		   when compile C code with W=1.
> Change in v6:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v5:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v4:
> 		1. Fixup the compatible.
> Change in v3:
> 		1. Add a function to gain sensor id an remove dts id.
> Change in v2:
> 		1. Remove error msg printing when addr ioremap has error.
> 		2. Make loongson2 thermal driver was built-in by default.
> 		3. Replace ls2k with loongson2.
> 		4. Remove CONFIG_PM_SLEEP and set pm function type was
> 		   __maybe_unused.
>
>   MAINTAINERS                         |   7 +
>   drivers/thermal/Kconfig             |  10 ++
>   drivers/thermal/Makefile            |   1 +
>   drivers/thermal/loongson2_thermal.c | 260 ++++++++++++++++++++++++++++
>   4 files changed, 278 insertions(+)
>   create mode 100644 drivers/thermal/loongson2_thermal.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 1b391ca7cf91..0d867573fe4c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12013,6 +12013,13 @@ F:	drivers/*/*loongarch*
>   F:	Documentation/loongarch/
>   F:	Documentation/translations/zh_CN/loongarch/
>   
> +LOONGSON-2 SOC SERIES THERMAL DRIVER
> +M:	zhanghongchen <zhanghongchen@loongson.cn>
> +M:	Yinbo Zhu <zhuyinbo@loongson.cn>
> +L:	linux-pm@vger.kernel.org
> +S:	Maintained
> +F:	drivers/thermal/loongson2_thermal.c
> +
>   LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
>   M:	Sathya Prakash <sathya.prakash@broadcom.com>
>   M:	Sreekanth Reddy <sreekanth.reddy@broadcom.com>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index e052dae614eb..93d84bcb16dd 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -504,4 +504,14 @@ config KHADAS_MCU_FAN_THERMAL
>   	  If you say yes here you get support for the FAN controlled
>   	  by the Microcontroller found on the Khadas VIM boards.
>   
> +config LOONGSON2_THERMAL
> +	tristate "Loongson-2 SoC series thermal driver"
> +	depends on LOONGARCH || COMPILE_TEST
> +	depends on OF
> +	help
> +	  Support for Thermal driver found on Loongson-2 SoC series platforms.
> +	  It supports one critical trip point and one passive trip point. The
> +	  cpufreq and the pwm fan is used as the cooling device to throttle
> +	  CPUs when the passive trip is crossed.
> +
>   endif
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 2506c6c8ca83..02f3db809858 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -61,3 +61,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
>   obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
>   obj-$(CONFIG_SPRD_THERMAL)	+= sprd_thermal.o
>   obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)	+= khadas_mcu_fan.o
> +obj-$(CONFIG_LOONGSON2_THERMAL)	+= loongson2_thermal.o
> diff --git a/drivers/thermal/loongson2_thermal.c b/drivers/thermal/loongson2_thermal.c
> new file mode 100644
> index 000000000000..2d495469e8dd
> --- /dev/null
> +++ b/drivers/thermal/loongson2_thermal.c
> @@ -0,0 +1,260 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Author: zhanghongchen <zhanghongchen@loongson.cn>
> + *         Yinbo Zhu <zhuyinbo@loongson.cn>
> + * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
> + */
> +
> +#include <linux/cpufreq.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/of_device.h>
> +#include <linux/thermal.h>
> +#include "thermal_hwmon.h"
> +
> +#define LOONGSON2_SOC_MAX_SENSOR_NUM			4
> +
> +#define LOONGSON2_TSENSOR_CTRL_HI			0x0
> +#define LOONGSON2_TSENSOR_CTRL_LO			0x8
> +#define LOONGSON2_TSENSOR_STATUS			0x10
> +#define LOONGSON2_TSENSOR_OUT				0x14
> +
> +struct loongson2_thermal_data {
> +	struct thermal_zone_device *tzd;
> +	int irq;
> +	int id;
> +	void __iomem *regs;
> +	struct platform_device *pdev;
> +	u16 ctrl_low_val;
> +	u16 ctrl_hi_val;
> +};
> +
> +static int loongson2_thermal_set(struct loongson2_thermal_data *data,
> +					int low, int high, bool enable)
> +{
> +	u64 reg_ctrl = 0;
> +	int reg_off = data->id * 2;
> +
> +	if (low > high)
> +		return -EINVAL;
> +
> +	low = max(low, -100);
> +	high = min(high, 155);
> +
> +	low += 100;
> +	high += 100;
> +
> +	reg_ctrl |= low;
> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +
> +	reg_ctrl = 0;
> +	reg_ctrl |= high;
> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
> +{
> +	u32 reg_val;
> +	struct loongson2_thermal_data *data = tz->devdata;
> +
> +	reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
> +	*temp = ((reg_val & 0xff) - 100) * 1000;
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_get_sensor_id(void)
> +{
> +	int ret, id;
> +	struct of_phandle_args sensor_specs;
> +	struct device_node *np, *sensor_np;
> +
> +	np = of_find_node_by_name(NULL, "thermal-zones");
> +	if (!np)
> +		return -ENODEV;
> +
> +	sensor_np = of_get_next_child(np, NULL);
> +	ret = of_parse_phandle_with_args(sensor_np, "thermal-sensors",
> +			"#thermal-sensor-cells",
> +			0, &sensor_specs);
> +	if (ret) {
> +		of_node_put(np);
> +		of_node_put(sensor_np);
> +		return ret;
> +	}
> +
> +	if (sensor_specs.args_count >= 1) {
> +		id = sensor_specs.args[0];
> +		WARN(sensor_specs.args_count > 1,
> +				"%s: too many cells in sensor specifier %d\n",
> +				sensor_specs.np->name, sensor_specs.args_count);
> +	} else {
> +		id = 0;
> +	}
> +
> +	of_node_put(np);
> +	of_node_put(sensor_np);
> +
> +	return id;
> +}
> +
> +static irqreturn_t loongson2_thermal_alarm_irq(int irq, void *dev)
> +{
> +	struct loongson2_thermal_data *data = dev;
> +
> +	/* clear interrupt */
> +	writeb(0x3, data->regs + LOONGSON2_TSENSOR_STATUS);
> +
> +	disable_irq_nosync(irq);
> +
> +	return IRQ_WAKE_THREAD;
> +}
> +
> +static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
> +{
> +	struct loongson2_thermal_data *data = dev;
> +
> +	thermal_zone_device_update(data->tzd,
> +				   THERMAL_EVENT_UNSPECIFIED);
> +	enable_irq(data->irq);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int loongson2_thermal_set_trips(struct thermal_zone_device *tz, int low, int high)
> +{
> +	struct loongson2_thermal_data *data = tz->devdata;
> +
> +	return loongson2_thermal_set(data, low/1000, high/1000, true);
> +}
> +
> +static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
> +	.get_temp = loongson2_thermal_get_temp,
> +	.set_trips = loongson2_thermal_set_trips,
> +};
> +
> +static int loongson2_thermal_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	struct loongson2_thermal_data *data;
> +	int ret;
> +
> +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> +	if (!data)
> +		return -ENOMEM;
> +
> +	data->pdev = pdev;
> +	platform_set_drvdata(pdev, data);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	data->regs = devm_ioremap(dev, res->start, resource_size(res));
> +	if (IS_ERR(data->regs))
> +		return PTR_ERR(data->regs);
> +
> +	/* get irq */
> +	data->irq = platform_get_irq(pdev, 0);
> +	if (data->irq < 0)
> +		return data->irq;
> +
> +	/* get id */
> +	data->id = loongson2_thermal_get_sensor_id();
> +	if (data->id > LOONGSON2_SOC_MAX_SENSOR_NUM - 1 || data->id < 0) {
> +		dev_err(dev, "sensor id error,must be in <0 ~ %d>\n",
> +				LOONGSON2_SOC_MAX_SENSOR_NUM - 1);
> +		return -EINVAL;
> +	}
> +
> +	writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
> +
> +	loongson2_thermal_set(data, 0, 0, false);
> +
> +	data->tzd = devm_thermal_of_zone_register(&pdev->dev, data->id, data,
> +			&loongson2_of_thermal_ops);
> +	if (IS_ERR(data->tzd))
> +		return dev_err_probe(&pdev->dev, PTR_ERR(data->tzd),
> +				"failed to register");
> +
> +	ret = devm_request_threaded_irq(dev, data->irq,
> +			loongson2_thermal_alarm_irq, loongson2_thermal_irq_thread,
> +			IRQF_ONESHOT, "loongson2_thermal", data);
> +	if (ret < 0)
> +		return dev_err_probe(dev, ret, "failed to request alarm irq\n");
> +
> +	/*
> +	 * Thermal_zone doesn't enable hwmon as default,
> +	 * enable it here
> +	 */
> +	data->tzd->tzp->no_hwmon = false;
> +	if (devm_thermal_add_hwmon_sysfs(data->tzd))
> +		dev_warn(&pdev->dev, "Failed to add hwmon sysfs attributes\n");
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_remove(struct platform_device *pdev)
> +{
> +	struct loongson2_thermal_data *data = platform_get_drvdata(pdev);
> +	int reg_off = data->id * 2;
> +
> +	/* disable interrupt */
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id of_loongson2_thermal_match[] = {
> +	{ .compatible = "loongson,ls2k-thermal",},
> +	{ /* end */ }
> +};
> +MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
> +
> +static int __maybe_unused loongson2_thermal_suspend(struct device *dev)
> +{
> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
> +	int reg_off = data->id * 2;
> +
> +	data->ctrl_low_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	data->ctrl_hi_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused loongson2_thermal_resume(struct device *dev)
> +{
> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
> +	int reg_off = data->id * 2;
> +
> +	writew(data->ctrl_low_val, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(data->ctrl_hi_val, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(loongson2_thermal_pm_ops,
> +			 loongson2_thermal_suspend, loongson2_thermal_resume);
> +
> +static struct platform_driver loongson2_thermal_driver = {
> +	.driver = {
> +		.name		= "loongson2_thermal",
> +		.pm = &loongson2_thermal_pm_ops,
> +		.of_match_table = of_loongson2_thermal_match,
> +	},
> +	.probe	= loongson2_thermal_probe,
> +	.remove	= loongson2_thermal_remove,
> +};
> +module_platform_driver(loongson2_thermal_driver);
> +
> +MODULE_DESCRIPTION("Loongson2 thermal driver");
> +MODULE_LICENSE("GPL");

Re: [PATCH v12 1/2] thermal: loongson-2: add thermal management support

[Daniel Lezcano]

On 01/02/2023 05:29, zhuyinbo wrote:
> 
> Friendly ping ?

Thanks for the reminder, before I can merge this patch I have to review 
it. But I have more material to work on before.



> 在 2022/11/14 上午10:47, Yinbo Zhu 写道:
>> This patch adds the support for Loongson-2 thermal sensor controller,
>> which can support maximum 4 sensors.
>>
>> It's based on thermal of framework:
>>   - Trip points defined in device tree.
>>   - Cpufreq as cooling device registered in Loongson-2 cpufreq driver.
>>   - Pwm fan as cooling device registered in hwmon pwm-fan driver.
>>
>> Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
>> Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
>> ---
>> Change in v12:
>>         1. Fixup it about min and max.
>>         2. Use dev_err_probe replace dev_err in 
>> devm_request_threaded_irq context.
>> Change in v11:
>>         1. Add min() and max() to replace related code in function
>>            loongson2_thermal_set.
>>         2. Add dev_err_probe to to replace related code for function
>>            return value use devm_thermal_of_zone_register.
>>         3. Replace thermal_add_hwmon_sysfs with 
>> devm_thermal_add_hwmon_sysfs
>>            and use dev_warn replace dev_err in this context.
>> Change in v10:
>>         1. Add all history change log information.
>> Change in v9:
>>         1. Switch new API that use devm_thermal_of_zone_register
>>            to replace previous interfaces.
>>         2. Add depend on LOONGARCH || COMPILE_TEST.
>> Change in v8:
>>                  1. Replace string loongson2/Loongson2/LOONGSON2 with 
>> loongson-2/
>>                     Loongson-2/LOONGSON-2 in Kconfig and commit log 
>> and MAINTAINERS
>>            files.
>> Change in v7:
>>         1. Split the modification of patch 3 and merge it into this 
>> patch.
>>         2. Remove the unless code annotation to fix the compile warning
>>            when compile C code with W=1.
>> Change in v6:
>>         1. NO change, but other patch in this series of patches set has
>>            changes.
>> Change in v5:
>>         1. NO change, but other patch in this series of patches set has
>>            changes.
>> Change in v4:
>>         1. Fixup the compatible.
>> Change in v3:
>>         1. Add a function to gain sensor id an remove dts id.
>> Change in v2:
>>         1. Remove error msg printing when addr ioremap has error.
>>         2. Make loongson2 thermal driver was built-in by default.
>>         3. Replace ls2k with loongson2.
>>         4. Remove CONFIG_PM_SLEEP and set pm function type was
>>            __maybe_unused.
>>
>>   MAINTAINERS                         |   7 +
>>   drivers/thermal/Kconfig             |  10 ++
>>   drivers/thermal/Makefile            |   1 +
>>   drivers/thermal/loongson2_thermal.c | 260 ++++++++++++++++++++++++++++
>>   4 files changed, 278 insertions(+)
>>   create mode 100644 drivers/thermal/loongson2_thermal.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 1b391ca7cf91..0d867573fe4c 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -12013,6 +12013,13 @@ F:    drivers/*/*loongarch*
>>   F:    Documentation/loongarch/
>>   F:    Documentation/translations/zh_CN/loongarch/
>> +LOONGSON-2 SOC SERIES THERMAL DRIVER
>> +M:    zhanghongchen <zhanghongchen@loongson.cn>
>> +M:    Yinbo Zhu <zhuyinbo@loongson.cn>
>> +L:    linux-pm@vger.kernel.org
>> +S:    Maintained
>> +F:    drivers/thermal/loongson2_thermal.c
>> +
>>   LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
>>   M:    Sathya Prakash <sathya.prakash@broadcom.com>
>>   M:    Sreekanth Reddy <sreekanth.reddy@broadcom.com>
>> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
>> index e052dae614eb..93d84bcb16dd 100644
>> --- a/drivers/thermal/Kconfig
>> +++ b/drivers/thermal/Kconfig
>> @@ -504,4 +504,14 @@ config KHADAS_MCU_FAN_THERMAL
>>         If you say yes here you get support for the FAN controlled
>>         by the Microcontroller found on the Khadas VIM boards.
>> +config LOONGSON2_THERMAL
>> +    tristate "Loongson-2 SoC series thermal driver"
>> +    depends on LOONGARCH || COMPILE_TEST
>> +    depends on OF
>> +    help
>> +      Support for Thermal driver found on Loongson-2 SoC series 
>> platforms.
>> +      It supports one critical trip point and one passive trip point. 
>> The
>> +      cpufreq and the pwm fan is used as the cooling device to throttle
>> +      CPUs when the passive trip is crossed.
>> +
>>   endif
>> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
>> index 2506c6c8ca83..02f3db809858 100644
>> --- a/drivers/thermal/Makefile
>> +++ b/drivers/thermal/Makefile
>> @@ -61,3 +61,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)    += uniphier_thermal.o
>>   obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
>>   obj-$(CONFIG_SPRD_THERMAL)    += sprd_thermal.o
>>   obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)    += khadas_mcu_fan.o
>> +obj-$(CONFIG_LOONGSON2_THERMAL)    += loongson2_thermal.o
>> diff --git a/drivers/thermal/loongson2_thermal.c 
>> b/drivers/thermal/loongson2_thermal.c
>> new file mode 100644
>> index 000000000000..2d495469e8dd
>> --- /dev/null
>> +++ b/drivers/thermal/loongson2_thermal.c
>> @@ -0,0 +1,260 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Author: zhanghongchen <zhanghongchen@loongson.cn>
>> + *         Yinbo Zhu <zhuyinbo@loongson.cn>
>> + * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
>> + */
>> +
>> +#include <linux/cpufreq.h>
>> +#include <linux/delay.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/io.h>
>> +#include <linux/of_device.h>
>> +#include <linux/thermal.h>
>> +#include "thermal_hwmon.h"
>> +
>> +#define LOONGSON2_SOC_MAX_SENSOR_NUM            4
>> +
>> +#define LOONGSON2_TSENSOR_CTRL_HI            0x0
>> +#define LOONGSON2_TSENSOR_CTRL_LO            0x8
>> +#define LOONGSON2_TSENSOR_STATUS            0x10
>> +#define LOONGSON2_TSENSOR_OUT                0x14
>> +
>> +struct loongson2_thermal_data {
>> +    struct thermal_zone_device *tzd;
>> +    int irq;
>> +    int id;
>> +    void __iomem *regs;
>> +    struct platform_device *pdev;
>> +    u16 ctrl_low_val;
>> +    u16 ctrl_hi_val;
>> +};
>> +
>> +static int loongson2_thermal_set(struct loongson2_thermal_data *data,
>> +                    int low, int high, bool enable)
>> +{
>> +    u64 reg_ctrl = 0;
>> +    int reg_off = data->id * 2;
>> +
>> +    if (low > high)
>> +        return -EINVAL;
>> +
>> +    low = max(low, -100);
>> +    high = min(high, 155);
>> +
>> +    low += 100;
>> +    high += 100;
>> +
>> +    reg_ctrl |= low;
>> +    reg_ctrl |= enable ? 0x100 : 0;
>> +    writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
>> +
>> +    reg_ctrl = 0;
>> +    reg_ctrl |= high;
>> +    reg_ctrl |= enable ? 0x100 : 0;
>> +    writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
>> +
>> +    return 0;
>> +}
>> +
>> +static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, 
>> int *temp)
>> +{
>> +    u32 reg_val;
>> +    struct loongson2_thermal_data *data = tz->devdata;
>> +
>> +    reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
>> +    *temp = ((reg_val & 0xff) - 100) * 1000;
>> +
>> +    return 0;
>> +}
>> +
>> +static int loongson2_thermal_get_sensor_id(void)
>> +{
>> +    int ret, id;
>> +    struct of_phandle_args sensor_specs;
>> +    struct device_node *np, *sensor_np;
>> +
>> +    np = of_find_node_by_name(NULL, "thermal-zones");
>> +    if (!np)
>> +        return -ENODEV;
>> +
>> +    sensor_np = of_get_next_child(np, NULL);
>> +    ret = of_parse_phandle_with_args(sensor_np, "thermal-sensors",
>> +            "#thermal-sensor-cells",
>> +            0, &sensor_specs);
>> +    if (ret) {
>> +        of_node_put(np);
>> +        of_node_put(sensor_np);
>> +        return ret;
>> +    }
>> +
>> +    if (sensor_specs.args_count >= 1) {
>> +        id = sensor_specs.args[0];
>> +        WARN(sensor_specs.args_count > 1,
>> +                "%s: too many cells in sensor specifier %d\n",
>> +                sensor_specs.np->name, sensor_specs.args_count);
>> +    } else {
>> +        id = 0;
>> +    }
>> +
>> +    of_node_put(np);
>> +    of_node_put(sensor_np);
>> +
>> +    return id;
>> +}
>> +
>> +static irqreturn_t loongson2_thermal_alarm_irq(int irq, void *dev)
>> +{
>> +    struct loongson2_thermal_data *data = dev;
>> +
>> +    /* clear interrupt */
>> +    writeb(0x3, data->regs + LOONGSON2_TSENSOR_STATUS);
>> +
>> +    disable_irq_nosync(irq);
>> +
>> +    return IRQ_WAKE_THREAD;
>> +}
>> +
>> +static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
>> +{
>> +    struct loongson2_thermal_data *data = dev;
>> +
>> +    thermal_zone_device_update(data->tzd,
>> +                   THERMAL_EVENT_UNSPECIFIED);
>> +    enable_irq(data->irq);
>> +
>> +    return IRQ_HANDLED;
>> +}
>> +
>> +static int loongson2_thermal_set_trips(struct thermal_zone_device 
>> *tz, int low, int high)
>> +{
>> +    struct loongson2_thermal_data *data = tz->devdata;
>> +
>> +    return loongson2_thermal_set(data, low/1000, high/1000, true);
>> +}
>> +
>> +static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
>> +    .get_temp = loongson2_thermal_get_temp,
>> +    .set_trips = loongson2_thermal_set_trips,
>> +};
>> +
>> +static int loongson2_thermal_probe(struct platform_device *pdev)
>> +{
>> +    struct device *dev = &pdev->dev;
>> +    struct resource *res;
>> +    struct loongson2_thermal_data *data;
>> +    int ret;
>> +
>> +    data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
>> +    if (!data)
>> +        return -ENOMEM;
>> +
>> +    data->pdev = pdev;
>> +    platform_set_drvdata(pdev, data);
>> +
>> +    res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +    data->regs = devm_ioremap(dev, res->start, resource_size(res));
>> +    if (IS_ERR(data->regs))
>> +        return PTR_ERR(data->regs);
>> +
>> +    /* get irq */
>> +    data->irq = platform_get_irq(pdev, 0);
>> +    if (data->irq < 0)
>> +        return data->irq;
>> +
>> +    /* get id */
>> +    data->id = loongson2_thermal_get_sensor_id();
>> +    if (data->id > LOONGSON2_SOC_MAX_SENSOR_NUM - 1 || data->id < 0) {
>> +        dev_err(dev, "sensor id error,must be in <0 ~ %d>\n",
>> +                LOONGSON2_SOC_MAX_SENSOR_NUM - 1);
>> +        return -EINVAL;
>> +    }
>> +
>> +    writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
>> +
>> +    loongson2_thermal_set(data, 0, 0, false);
>> +
>> +    data->tzd = devm_thermal_of_zone_register(&pdev->dev, data->id, 
>> data,
>> +            &loongson2_of_thermal_ops);
>> +    if (IS_ERR(data->tzd))
>> +        return dev_err_probe(&pdev->dev, PTR_ERR(data->tzd),
>> +                "failed to register");
>> +
>> +    ret = devm_request_threaded_irq(dev, data->irq,
>> +            loongson2_thermal_alarm_irq, loongson2_thermal_irq_thread,
>> +            IRQF_ONESHOT, "loongson2_thermal", data);
>> +    if (ret < 0)
>> +        return dev_err_probe(dev, ret, "failed to request alarm irq\n");
>> +
>> +    /*
>> +     * Thermal_zone doesn't enable hwmon as default,
>> +     * enable it here
>> +     */
>> +    data->tzd->tzp->no_hwmon = false;
>> +    if (devm_thermal_add_hwmon_sysfs(data->tzd))
>> +        dev_warn(&pdev->dev, "Failed to add hwmon sysfs attributes\n");
>> +
>> +    return 0;
>> +}
>> +
>> +static int loongson2_thermal_remove(struct platform_device *pdev)
>> +{
>> +    struct loongson2_thermal_data *data = platform_get_drvdata(pdev);
>> +    int reg_off = data->id * 2;
>> +
>> +    /* disable interrupt */
>> +    writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
>> +    writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
>> +
>> +    return 0;
>> +}
>> +
>> +static const struct of_device_id of_loongson2_thermal_match[] = {
>> +    { .compatible = "loongson,ls2k-thermal",},
>> +    { /* end */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
>> +
>> +static int __maybe_unused loongson2_thermal_suspend(struct device *dev)
>> +{
>> +    struct loongson2_thermal_data *data = dev_get_drvdata(dev);
>> +    int reg_off = data->id * 2;
>> +
>> +    data->ctrl_low_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_LO 
>> + reg_off);
>> +    data->ctrl_hi_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_HI 
>> + reg_off);
>> +
>> +    writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
>> +    writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
>> +
>> +    return 0;
>> +}
>> +
>> +static int __maybe_unused loongson2_thermal_resume(struct device *dev)
>> +{
>> +    struct loongson2_thermal_data *data = dev_get_drvdata(dev);
>> +    int reg_off = data->id * 2;
>> +
>> +    writew(data->ctrl_low_val, data->regs + LOONGSON2_TSENSOR_CTRL_LO 
>> + reg_off);
>> +    writew(data->ctrl_hi_val, data->regs + LOONGSON2_TSENSOR_CTRL_HI 
>> + reg_off);
>> +
>> +    return 0;
>> +}
>> +
>> +static SIMPLE_DEV_PM_OPS(loongson2_thermal_pm_ops,
>> +             loongson2_thermal_suspend, loongson2_thermal_resume);
>> +
>> +static struct platform_driver loongson2_thermal_driver = {
>> +    .driver = {
>> +        .name        = "loongson2_thermal",
>> +        .pm = &loongson2_thermal_pm_ops,
>> +        .of_match_table = of_loongson2_thermal_match,
>> +    },
>> +    .probe    = loongson2_thermal_probe,
>> +    .remove    = loongson2_thermal_remove,
>> +};
>> +module_platform_driver(loongson2_thermal_driver);
>> +
>> +MODULE_DESCRIPTION("Loongson2 thermal driver");
>> +MODULE_LICENSE("GPL");
> 

-- 
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

Re: [PATCH v12 1/2] thermal: loongson-2: add thermal management support

[Daniel Lezcano]

On Mon, Nov 14, 2022 at 10:47:08AM +0800, Yinbo Zhu wrote:
> This patch adds the support for Loongson-2 thermal sensor controller,
> which can support maximum 4 sensors.
> 
> It's based on thermal of framework:
>  - Trip points defined in device tree.
>  - Cpufreq as cooling device registered in Loongson-2 cpufreq driver.
>  - Pwm fan as cooling device registered in hwmon pwm-fan driver.
> 

This changelog is not helpful.

Please describe how works the sensor. 

> Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
> Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
> ---
> Change in v12:
> 		1. Fixup it about min and max.
> 		2. Use dev_err_probe replace dev_err in devm_request_threaded_irq context.
> Change in v11:
> 		1. Add min() and max() to replace related code in function
> 		   loongson2_thermal_set.
> 		2. Add dev_err_probe to to replace related code for function
> 		   return value use devm_thermal_of_zone_register.
> 		3. Replace thermal_add_hwmon_sysfs with devm_thermal_add_hwmon_sysfs
> 		   and use dev_warn replace dev_err in this context.
> Change in v10:
> 		1. Add all history change log information.
> Change in v9:
> 		1. Switch new API that use devm_thermal_of_zone_register
> 		   to replace previous interfaces.
> 		2. Add depend on LOONGARCH || COMPILE_TEST.
> Change in v8:
>                 1. Replace string loongson2/Loongson2/LOONGSON2 with loongson-2/
>                    Loongson-2/LOONGSON-2 in Kconfig and commit log and MAINTAINERS
> 		   files.
> Change in v7:
> 		1. Split the modification of patch 3 and merge it into this patch.
> 		2. Remove the unless code annotation to fix the compile warning
> 		   when compile C code with W=1.
> Change in v6:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v5:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v4:
> 		1. Fixup the compatible.
> Change in v3:
> 		1. Add a function to gain sensor id an remove dts id.
> Change in v2:
> 		1. Remove error msg printing when addr ioremap has error.
> 		2. Make loongson2 thermal driver was built-in by default.
> 		3. Replace ls2k with loongson2.
> 		4. Remove CONFIG_PM_SLEEP and set pm function type was
> 		   __maybe_unused.
> 
>  MAINTAINERS                         |   7 +
>  drivers/thermal/Kconfig             |  10 ++
>  drivers/thermal/Makefile            |   1 +
>  drivers/thermal/loongson2_thermal.c | 260 ++++++++++++++++++++++++++++
>  4 files changed, 278 insertions(+)
>  create mode 100644 drivers/thermal/loongson2_thermal.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 1b391ca7cf91..0d867573fe4c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12013,6 +12013,13 @@ F:	drivers/*/*loongarch*
>  F:	Documentation/loongarch/
>  F:	Documentation/translations/zh_CN/loongarch/
>  
> +LOONGSON-2 SOC SERIES THERMAL DRIVER
> +M:	zhanghongchen <zhanghongchen@loongson.cn>
> +M:	Yinbo Zhu <zhuyinbo@loongson.cn>
> +L:	linux-pm@vger.kernel.org
> +S:	Maintained
> +F:	drivers/thermal/loongson2_thermal.c
> +
>  LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
>  M:	Sathya Prakash <sathya.prakash@broadcom.com>
>  M:	Sreekanth Reddy <sreekanth.reddy@broadcom.com>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index e052dae614eb..93d84bcb16dd 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -504,4 +504,14 @@ config KHADAS_MCU_FAN_THERMAL
>  	  If you say yes here you get support for the FAN controlled
>  	  by the Microcontroller found on the Khadas VIM boards.
>  
> +config LOONGSON2_THERMAL
> +	tristate "Loongson-2 SoC series thermal driver"
> +	depends on LOONGARCH || COMPILE_TEST
> +	depends on OF

Please check commit 8df4ef3eaa62b

> +	help
> +	  Support for Thermal driver found on Loongson-2 SoC series platforms.
> +	  It supports one critical trip point and one passive trip point. The
> +	  cpufreq and the pwm fan is used as the cooling device to throttle
> +	  CPUs when the passive trip is crossed.

The help is misleading. The thermal framework supports the trip points, not the
driver. Also, the cooling devices association is related to the thermal zone,
not the sensor.

>  endif
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 2506c6c8ca83..02f3db809858 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -61,3 +61,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
>  obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
>  obj-$(CONFIG_SPRD_THERMAL)	+= sprd_thermal.o
>  obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)	+= khadas_mcu_fan.o
> +obj-$(CONFIG_LOONGSON2_THERMAL)	+= loongson2_thermal.o
> diff --git a/drivers/thermal/loongson2_thermal.c b/drivers/thermal/loongson2_thermal.c
> new file mode 100644
> index 000000000000..2d495469e8dd
> --- /dev/null
> +++ b/drivers/thermal/loongson2_thermal.c
> @@ -0,0 +1,260 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Author: zhanghongchen <zhanghongchen@loongson.cn>
> + *         Yinbo Zhu <zhuyinbo@loongson.cn>
> + * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
> + */
> +
> +#include <linux/cpufreq.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/of_device.h>
> +#include <linux/thermal.h>
> +#include "thermal_hwmon.h"
> +
> +#define LOONGSON2_SOC_MAX_SENSOR_NUM			4
> +
> +#define LOONGSON2_TSENSOR_CTRL_HI			0x0
> +#define LOONGSON2_TSENSOR_CTRL_LO			0x8
> +#define LOONGSON2_TSENSOR_STATUS			0x10
> +#define LOONGSON2_TSENSOR_OUT				0x14
> +
> +struct loongson2_thermal_data {
> +	struct thermal_zone_device *tzd;

'tzd' won't be needed after taking into account the comments

> +	int irq;

'irq' won't be needed after taking into account the comments

> +	int id;
> +	void __iomem *regs;
> +	struct platform_device *pdev;

'pdev' is not needed

> +	u16 ctrl_low_val;
> +	u16 ctrl_hi_val;

Those fields won't be needed after taking into account the comments

> +};
> +
> +static int loongson2_thermal_set(struct loongson2_thermal_data *data,
> +					int low, int high, bool enable)
> +{
> +	u64 reg_ctrl = 0;
> +	int reg_off = data->id * 2;
> +
> +	if (low > high)
> +		return -EINVAL;
> +
> +	low = max(low, -100);
> +	high = min(high, 155);
> +
> +	low += 100;
> +	high += 100;

Why are those values added to the low and high ? Did you mean low += 0x100 ?

Mind to describe a bit the register layout?

> +	reg_ctrl |= low;

	reg_ctrl = low;

> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +
> +	reg_ctrl = 0;

No need to reset the variable.

	reg_ctrl = high;

> +	reg_ctrl |= high;
> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
> +{
> +	u32 reg_val;
> +	struct loongson2_thermal_data *data = tz->devdata;
> +
> +	reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
> +	*temp = ((reg_val & 0xff) - 100) * 1000;

Why '-100' ?

Is the unit returned 'degrees' ?

> +	return 0;
> +}
> +
> +static int loongson2_thermal_get_sensor_id(void)
> +{
> +	int ret, id;
> +	struct of_phandle_args sensor_specs;
> +	struct device_node *np, *sensor_np;
> +
> +	np = of_find_node_by_name(NULL, "thermal-zones");
> +	if (!np)
> +		return -ENODEV;
> +
> +	sensor_np = of_get_next_child(np, NULL);
> +	ret = of_parse_phandle_with_args(sensor_np, "thermal-sensors",
> +			"#thermal-sensor-cells",
> +			0, &sensor_specs);
> +	if (ret) {
> +		of_node_put(np);
> +		of_node_put(sensor_np);
> +		return ret;
> +	}
> +
> +	if (sensor_specs.args_count >= 1) {
> +		id = sensor_specs.args[0];
> +		WARN(sensor_specs.args_count > 1,
> +				"%s: too many cells in sensor specifier %d\n",
> +				sensor_specs.np->name, sensor_specs.args_count);
> +	} else {
> +		id = 0;
> +	}
> +
> +	of_node_put(np);
> +	of_node_put(sensor_np);
> +
> +	return id;
> +}

This is not needed. Please do not tamper with the OF code in the sensor.

You should know the id in this sensor driver

> +static irqreturn_t loongson2_thermal_alarm_irq(int irq, void *dev)
> +{
> +	struct loongson2_thermal_data *data = dev;
> +
> +	/* clear interrupt */
> +	writeb(0x3, data->regs + LOONGSON2_TSENSOR_STATUS);
> +
> +	disable_irq_nosync(irq);
> +
> +	return IRQ_WAKE_THREAD;
> +}
> +
> +static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
> +{
> +	struct loongson2_thermal_data *data = dev;
> +
> +	thermal_zone_device_update(data->tzd,
> +				   THERMAL_EVENT_UNSPECIFIED);
> +	enable_irq(data->irq);
> +
> +	return IRQ_HANDLED;
> +}

It is not necessary to create a couple of irq callback for this.

Just clear the interrupt in loongson2_thermal_irq_thread() and drop loongson2_thermal_alarm_irq().

> +
> +static int loongson2_thermal_set_trips(struct thermal_zone_device *tz, int low, int high)
> +{
> +	struct loongson2_thermal_data *data = tz->devdata;
> +
> +	return loongson2_thermal_set(data, low/1000, high/1000, true);
> +}
> +
> +static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
> +	.get_temp = loongson2_thermal_get_temp,
> +	.set_trips = loongson2_thermal_set_trips,
> +};
> +
> +static int loongson2_thermal_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	struct loongson2_thermal_data *data;
> +	int ret;
> +
> +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> +	if (!data)
> +		return -ENOMEM;
> +
> +	data->pdev = pdev;
> +	platform_set_drvdata(pdev, data);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	data->regs = devm_ioremap(dev, res->start, resource_size(res));
> +	if (IS_ERR(data->regs))
> +		return PTR_ERR(data->regs);
> +
> +	/* get irq */
> +	data->irq = platform_get_irq(pdev, 0);
> +	if (data->irq < 0)
> +		return data->irq;
> +
> +	/* get id */
> +	data->id = loongson2_thermal_get_sensor_id();
> +	if (data->id > LOONGSON2_SOC_MAX_SENSOR_NUM - 1 || data->id < 0) {
> +		dev_err(dev, "sensor id error,must be in <0 ~ %d>\n",
> +				LOONGSON2_SOC_MAX_SENSOR_NUM - 1);
> +		return -EINVAL;
> +	}
> +
> +	writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
> +
> +	loongson2_thermal_set(data, 0, 0, false);

It would be nicer to use a reset line if it is available

> +	data->tzd = devm_thermal_of_zone_register(&pdev->dev, data->id, data,
> +			&loongson2_of_thermal_ops);
> +	if (IS_ERR(data->tzd))
> +		return dev_err_probe(&pdev->dev, PTR_ERR(data->tzd),
> +				"failed to register");

If you want to not care about the kind of SoC the sensor belongs to, you can
use the return value of devm_thermal_of_zone_register() which returns -ENODEV
and which is not considered as an error.

IOW:

	for (i = 0; i < LOONGSON2_SOC_MAX_SENSOR_NUM; i++) {

		tzd = devm_thermal_of_zone_register(&pdev->dev, i,
			data, &loongson2_of_thermal_ops);
		if (!IS_ERR(tzd))
			break;

		if (PTR_ERR(tzd) != ENODEV)
			continue;

		return dev_err_probe(&pdev->dev, PTR_ERR(tzd),
	                             "failed to register");
	}

> +	ret = devm_request_threaded_irq(dev, data->irq,
> +			loongson2_thermal_alarm_irq, loongson2_thermal_irq_thread,
> +			IRQF_ONESHOT, "loongson2_thermal", data);

Pass 'tzd' instead of 'data'

> +	if (ret < 0)
> +		return dev_err_probe(dev, ret, "failed to request alarm irq\n");
> +
> +	/*
> +	 * Thermal_zone doesn't enable hwmon as default,
> +	 * enable it here
> +	 */
> +	data->tzd->tzp->no_hwmon = false;

This is used when registering the thermal zone. Setting it after registering
the thermal zone has no effect. The line can be dropped.

> +	if (devm_thermal_add_hwmon_sysfs(data->tzd))
> +		dev_warn(&pdev->dev, "Failed to add hwmon sysfs attributes\n");
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_remove(struct platform_device *pdev)
> +{
> +	struct loongson2_thermal_data *data = platform_get_drvdata(pdev);
> +	int reg_off = data->id * 2;
> +
> +	/* disable interrupt */
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);

The interrupt is disabled with the driver removal as it was registered with the
devres version devm_thermal_of_zone_register()

> +
> +	return 0;
> +}
> +
> +static const struct of_device_id of_loongson2_thermal_match[] = {
> +	{ .compatible = "loongson,ls2k-thermal",},

You may want to add the sensor id in the data field. Probably depending on the
kind of SoC, one or several sensors will be used. 

> +	{ /* end */ }
> +};
> +MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
> +
> +static int __maybe_unused loongson2_thermal_suspend(struct device *dev)
> +{
> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
> +	int reg_off = data->id * 2;
> +
> +	data->ctrl_low_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	data->ctrl_hi_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused loongson2_thermal_resume(struct device *dev)
> +{
> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
> +	int reg_off = data->id * 2;
> +
> +	writew(data->ctrl_low_val, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
> +	writew(data->ctrl_hi_val, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> +
> +	return 0;
> +}

It is not necessary to save and restore the low and high temperatures for the
$trip points because the thermal framework core code will call at POST_SUSPEND
thermal_zone_device_update() which in turns get the temperature and sets the
trip points.

> +
> +static SIMPLE_DEV_PM_OPS(loongson2_thermal_pm_ops,
> +			 loongson2_thermal_suspend, loongson2_thermal_resume);
> +
> +static struct platform_driver loongson2_thermal_driver = {
> +	.driver = {
> +		.name		= "loongson2_thermal",
> +		.pm = &loongson2_thermal_pm_ops,
> +		.of_match_table = of_loongson2_thermal_match,
> +	},
> +	.probe	= loongson2_thermal_probe,
> +	.remove	= loongson2_thermal_remove,
> +};
> +module_platform_driver(loongson2_thermal_driver);
> +
> +MODULE_DESCRIPTION("Loongson2 thermal driver");
> +MODULE_LICENSE("GPL");
> -- 
> 2.31.1
> 

-- 

 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

Re: [PATCH v12 1/2] thermal: loongson-2: add thermal management support

[zhuyinbo]

在 2023/2/6 下午9:59, Daniel Lezcano 写道:

> On Mon, Nov 14, 2022 at 10:47:08AM +0800, Yinbo Zhu wrote:
>> This patch adds the support for Loongson-2 thermal sensor controller,
>> which can support maximum 4 sensors.
>>
>> It's based on thermal of framework:
>>   - Trip points defined in device tree.
>>   - Cpufreq as cooling device registered in Loongson-2 cpufreq driver.
>>   - Pwm fan as cooling device registered in hwmon pwm-fan driver.
>>
> This changelog is not helpful.
>
> Please describe how works the sensor.
okay, I got it.
>
>> Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
>> Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
>> ---
>> Change in v12:
>> 		1. Fixup it about min and max.
>> 		2. Use dev_err_probe replace dev_err in devm_request_threaded_irq context.
>> Change in v11:
>> 		1. Add min() and max() to replace related code in function
>> 		   loongson2_thermal_set.
>> 		2. Add dev_err_probe to to replace related code for function
>> 		   return value use devm_thermal_of_zone_register.
>> 		3. Replace thermal_add_hwmon_sysfs with devm_thermal_add_hwmon_sysfs
>> 		   and use dev_warn replace dev_err in this context.
>> Change in v10:
>> 		1. Add all history change log information.
>> Change in v9:
>> 		1. Switch new API that use devm_thermal_of_zone_register
>> 		   to replace previous interfaces.
>> 		2. Add depend on LOONGARCH || COMPILE_TEST.
>> Change in v8:
>>                  1. Replace string loongson2/Loongson2/LOONGSON2 with loongson-2/
>>                     Loongson-2/LOONGSON-2 in Kconfig and commit log and MAINTAINERS
>> 		   files.
>> Change in v7:
>> 		1. Split the modification of patch 3 and merge it into this patch.
>> 		2. Remove the unless code annotation to fix the compile warning
>> 		   when compile C code with W=1.
>> Change in v6:
>> 		1. NO change, but other patch in this series of patches set has
>> 		   changes.
>> Change in v5:
>> 		1. NO change, but other patch in this series of patches set has
>> 		   changes.
>> Change in v4:
>> 		1. Fixup the compatible.
>> Change in v3:
>> 		1. Add a function to gain sensor id an remove dts id.
>> Change in v2:
>> 		1. Remove error msg printing when addr ioremap has error.
>> 		2. Make loongson2 thermal driver was built-in by default.
>> 		3. Replace ls2k with loongson2.
>> 		4. Remove CONFIG_PM_SLEEP and set pm function type was
>> 		   __maybe_unused.
>>
>>   MAINTAINERS                         |   7 +
>>   drivers/thermal/Kconfig             |  10 ++
>>   drivers/thermal/Makefile            |   1 +
>>   drivers/thermal/loongson2_thermal.c | 260 ++++++++++++++++++++++++++++
>>   4 files changed, 278 insertions(+)
>>   create mode 100644 drivers/thermal/loongson2_thermal.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 1b391ca7cf91..0d867573fe4c 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -12013,6 +12013,13 @@ F:	drivers/*/*loongarch*
>>   F:	Documentation/loongarch/
>>   F:	Documentation/translations/zh_CN/loongarch/
>>   
>> +LOONGSON-2 SOC SERIES THERMAL DRIVER
>> +M:	zhanghongchen <zhanghongchen@loongson.cn>
>> +M:	Yinbo Zhu <zhuyinbo@loongson.cn>
>> +L:	linux-pm@vger.kernel.org
>> +S:	Maintained
>> +F:	drivers/thermal/loongson2_thermal.c
>> +
>>   LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
>>   M:	Sathya Prakash <sathya.prakash@broadcom.com>
>>   M:	Sreekanth Reddy <sreekanth.reddy@broadcom.com>
>> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
>> index e052dae614eb..93d84bcb16dd 100644
>> --- a/drivers/thermal/Kconfig
>> +++ b/drivers/thermal/Kconfig
>> @@ -504,4 +504,14 @@ config KHADAS_MCU_FAN_THERMAL
>>   	  If you say yes here you get support for the FAN controlled
>>   	  by the Microcontroller found on the Khadas VIM boards.
>>   
>> +config LOONGSON2_THERMAL
>> +	tristate "Loongson-2 SoC series thermal driver"
>> +	depends on LOONGARCH || COMPILE_TEST
>> +	depends on OF
> Please check commit 8df4ef3eaa62b
I will remove the 'COMPILE_TEST'.
>
>> +	help
>> +	  Support for Thermal driver found on Loongson-2 SoC series platforms.
>> +	  It supports one critical trip point and one passive trip point. The
>> +	  cpufreq and the pwm fan is used as the cooling device to throttle
>> +	  CPUs when the passive trip is crossed.
> The help is misleading. The thermal framework supports the trip points, not the
> driver. Also, the cooling devices association is related to the thermal zone,
> not the sensor.
okay, I will change it.
>
>>   endif
>> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
>> index 2506c6c8ca83..02f3db809858 100644
>> --- a/drivers/thermal/Makefile
>> +++ b/drivers/thermal/Makefile
>> @@ -61,3 +61,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
>>   obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
>>   obj-$(CONFIG_SPRD_THERMAL)	+= sprd_thermal.o
>>   obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)	+= khadas_mcu_fan.o
>> +obj-$(CONFIG_LOONGSON2_THERMAL)	+= loongson2_thermal.o
>> diff --git a/drivers/thermal/loongson2_thermal.c b/drivers/thermal/loongson2_thermal.c
>> new file mode 100644
>> index 000000000000..2d495469e8dd
>> --- /dev/null
>> +++ b/drivers/thermal/loongson2_thermal.c
>> @@ -0,0 +1,260 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Author: zhanghongchen <zhanghongchen@loongson.cn>
>> + *         Yinbo Zhu <zhuyinbo@loongson.cn>
>> + * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
>> + */
>> +
>> +#include <linux/cpufreq.h>
>> +#include <linux/delay.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/io.h>
>> +#include <linux/of_device.h>
>> +#include <linux/thermal.h>
>> +#include "thermal_hwmon.h"
>> +
>> +#define LOONGSON2_SOC_MAX_SENSOR_NUM			4
>> +
>> +#define LOONGSON2_TSENSOR_CTRL_HI			0x0
>> +#define LOONGSON2_TSENSOR_CTRL_LO			0x8
>> +#define LOONGSON2_TSENSOR_STATUS			0x10
>> +#define LOONGSON2_TSENSOR_OUT				0x14
>> +
>> +struct loongson2_thermal_data {
>> +	struct thermal_zone_device *tzd;
> 'tzd' won't be needed after taking into account the comments

The 'tzd' element is needed,  because the thermal_zone_device_update 
need pass a data->tzd element.

static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
{
         struct loongson2_thermal_data *data = dev;

         thermal_zone_device_update(data->tzd,
                                    THERMAL_EVENT_UNSPECIFIED);
         enable_irq(data->irq);

         return IRQ_HANDLED;
}

>
>> +	int irq;
> 'irq' won't be needed after taking into account the comments
I will drop it.
>> +	int id;
>> +	void __iomem *regs;
>> +	struct platform_device *pdev;
> 'pdev' is not needed
I will drop it.
>
>> +	u16 ctrl_low_val;
>> +	u16 ctrl_hi_val;
> Those fields won't be needed after taking into account the comments
I will drop it.
>> +};
>> +
>> +static int loongson2_thermal_set(struct loongson2_thermal_data *data,
>> +					int low, int high, bool enable)
>> +{
>> +	u64 reg_ctrl = 0;
>> +	int reg_off = data->id * 2;
>> +
>> +	if (low > high)
>> +		return -EINVAL;
>> +
>> +	low = max(low, -100);
>> +	high = min(high, 155);
>> +
>> +	low += 100;
>> +	high += 100;
> Why are those values added to the low and high ? Did you mean low += 0x100 ?
>
> Mind to describe a bit the register layout?

node(cpu) temp = Thens0_out -100,

low and high is record node temp, so low and high need add '100' as 
Thens0_out.


eg.  Thsens_int_ctrl_Hi  register layout:

[7:0]:  High temperature range (Thens0_out range)

[8:8]: High temperature interrupt enable bit

>
>> +	reg_ctrl |= low;
> 	reg_ctrl = low;
okay,  I will change it.
>
>> +	reg_ctrl |= enable ? 0x100 : 0;
>> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
>> +
>> +	reg_ctrl = 0;
> No need to reset the variable.
>
> 	reg_ctrl = high;
okay,  I will change it.
>
>> +	reg_ctrl |= high;
>> +	reg_ctrl |= enable ? 0x100 : 0;
>> +	writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
>> +
>> +	return 0;
>> +}
>> +
>> +static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
>> +{
>> +	u32 reg_val;
>> +	struct loongson2_thermal_data *data = tz->devdata;
>> +
>> +	reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
>> +	*temp = ((reg_val & 0xff) - 100) * 1000;
> Why '-100' ?
>
> Is the unit returned 'degrees' ?

node(cpu) temp = Thens0_out -100,

Here we need to get a node temp.

>
>> +	return 0;
>> +}
>> +
>> +static int loongson2_thermal_get_sensor_id(void)
>> +{
>> +	int ret, id;
>> +	struct of_phandle_args sensor_specs;
>> +	struct device_node *np, *sensor_np;
>> +
>> +	np = of_find_node_by_name(NULL, "thermal-zones");
>> +	if (!np)
>> +		return -ENODEV;
>> +
>> +	sensor_np = of_get_next_child(np, NULL);
>> +	ret = of_parse_phandle_with_args(sensor_np, "thermal-sensors",
>> +			"#thermal-sensor-cells",
>> +			0, &sensor_specs);
>> +	if (ret) {
>> +		of_node_put(np);
>> +		of_node_put(sensor_np);
>> +		return ret;
>> +	}
>> +
>> +	if (sensor_specs.args_count >= 1) {
>> +		id = sensor_specs.args[0];
>> +		WARN(sensor_specs.args_count > 1,
>> +				"%s: too many cells in sensor specifier %d\n",
>> +				sensor_specs.np->name, sensor_specs.args_count);
>> +	} else {
>> +		id = 0;
>> +	}
>> +
>> +	of_node_put(np);
>> +	of_node_put(sensor_np);
>> +
>> +	return id;
>> +}
> This is not needed. Please do not tamper with the OF code in the sensor.
>
> You should know the id in this sensor driver
okay, I got it, I will change it.
>
>> +static irqreturn_t loongson2_thermal_alarm_irq(int irq, void *dev)
>> +{
>> +	struct loongson2_thermal_data *data = dev;
>> +
>> +	/* clear interrupt */
>> +	writeb(0x3, data->regs + LOONGSON2_TSENSOR_STATUS);
>> +
>> +	disable_irq_nosync(irq);
>> +
>> +	return IRQ_WAKE_THREAD;
>> +}
>> +
>> +static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
>> +{
>> +	struct loongson2_thermal_data *data = dev;
>> +
>> +	thermal_zone_device_update(data->tzd,
>> +				   THERMAL_EVENT_UNSPECIFIED);
>> +	enable_irq(data->irq);
>> +
>> +	return IRQ_HANDLED;
>> +}
> It is not necessary to create a couple of irq callback for this.
>
> Just clear the interrupt in loongson2_thermal_irq_thread() and drop loongson2_thermal_alarm_irq().
okay, I will change it.
>
>> +
>> +static int loongson2_thermal_set_trips(struct thermal_zone_device *tz, int low, int high)
>> +{
>> +	struct loongson2_thermal_data *data = tz->devdata;
>> +
>> +	return loongson2_thermal_set(data, low/1000, high/1000, true);
>> +}
>> +
>> +static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
>> +	.get_temp = loongson2_thermal_get_temp,
>> +	.set_trips = loongson2_thermal_set_trips,
>> +};
>> +
>> +static int loongson2_thermal_probe(struct platform_device *pdev)
>> +{
>> +	struct device *dev = &pdev->dev;
>> +	struct resource *res;
>> +	struct loongson2_thermal_data *data;
>> +	int ret;
>> +
>> +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
>> +	if (!data)
>> +		return -ENOMEM;
>> +
>> +	data->pdev = pdev;
>> +	platform_set_drvdata(pdev, data);
>> +
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +	data->regs = devm_ioremap(dev, res->start, resource_size(res));
>> +	if (IS_ERR(data->regs))
>> +		return PTR_ERR(data->regs);
>> +
>> +	/* get irq */
>> +	data->irq = platform_get_irq(pdev, 0);
>> +	if (data->irq < 0)
>> +		return data->irq;
>> +
>> +	/* get id */
>> +	data->id = loongson2_thermal_get_sensor_id();
>> +	if (data->id > LOONGSON2_SOC_MAX_SENSOR_NUM - 1 || data->id < 0) {
>> +		dev_err(dev, "sensor id error,must be in <0 ~ %d>\n",
>> +				LOONGSON2_SOC_MAX_SENSOR_NUM - 1);
>> +		return -EINVAL;
>> +	}
>> +
>> +	writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
>> +
>> +	loongson2_thermal_set(data, 0, 0, false);
> It would be nicer to use a reset line if it is available
sorry, I don't get your meaning. Please describe more details about 
'reset line'.
>
>> +	data->tzd = devm_thermal_of_zone_register(&pdev->dev, data->id, data,
>> +			&loongson2_of_thermal_ops);
>> +	if (IS_ERR(data->tzd))
>> +		return dev_err_probe(&pdev->dev, PTR_ERR(data->tzd),
>> +				"failed to register");
> If you want to not care about the kind of SoC the sensor belongs to, you can
> use the return value of devm_thermal_of_zone_register() which returns -ENODEV
> and which is not considered as an error.
okay, I got it.
>
> IOW:
>
> 	for (i = 0; i < LOONGSON2_SOC_MAX_SENSOR_NUM; i++) {
>
> 		tzd = devm_thermal_of_zone_register(&pdev->dev, i,
> 			data, &loongson2_of_thermal_ops);
> 		if (!IS_ERR(tzd))
> 			break;
>
> 		if (PTR_ERR(tzd) != ENODEV)
> 			continue;
>
> 		return dev_err_probe(&pdev->dev, PTR_ERR(tzd),
> 	                             "failed to register");
> 	}
>
>> +	ret = devm_request_threaded_irq(dev, data->irq,
>> +			loongson2_thermal_alarm_irq, loongson2_thermal_irq_thread,
>> +			IRQF_ONESHOT, "loongson2_thermal", data);
> Pass 'tzd' instead of 'data'
I will change it.
>
>> +	if (ret < 0)
>> +		return dev_err_probe(dev, ret, "failed to request alarm irq\n");
>> +
>> +	/*
>> +	 * Thermal_zone doesn't enable hwmon as default,
>> +	 * enable it here
>> +	 */
>> +	data->tzd->tzp->no_hwmon = false;
> This is used when registering the thermal zone. Setting it after registering
> the thermal zone has no effect. The line can be dropped.
okay, I will drop it.
>
>> +	if (devm_thermal_add_hwmon_sysfs(data->tzd))
>> +		dev_warn(&pdev->dev, "Failed to add hwmon sysfs attributes\n");
>> +
>> +	return 0;
>> +}
>> +
>> +static int loongson2_thermal_remove(struct platform_device *pdev)
>> +{
>> +	struct loongson2_thermal_data *data = platform_get_drvdata(pdev);
>> +	int reg_off = data->id * 2;
>> +
>> +	/* disable interrupt */
>> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
>> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
> The interrupt is disabled with the driver removal as it was registered with the
> devres version devm_thermal_of_zone_register()
I will remove it.
>
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct of_device_id of_loongson2_thermal_match[] = {
>> +	{ .compatible = "loongson,ls2k-thermal",},
> You may want to add the sensor id in the data field. Probably depending on the
> kind of SoC, one or several sensors will be used.
okay, I will add it.
>
>> +	{ /* end */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
>> +
>> +static int __maybe_unused loongson2_thermal_suspend(struct device *dev)
>> +{
>> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
>> +	int reg_off = data->id * 2;
>> +
>> +	data->ctrl_low_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
>> +	data->ctrl_hi_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
>> +
>> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
>> +	writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
>> +
>> +	return 0;
>> +}
>> +
>> +static int __maybe_unused loongson2_thermal_resume(struct device *dev)
>> +{
>> +	struct loongson2_thermal_data *data = dev_get_drvdata(dev);
>> +	int reg_off = data->id * 2;
>> +
>> +	writew(data->ctrl_low_val, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
>> +	writew(data->ctrl_hi_val, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
>> +
>> +	return 0;
>> +}
> It is not necessary to save and restore the low and high temperatures for the
> $trip points because the thermal framework core code will call at POST_SUSPEND
> thermal_zone_device_update() which in turns get the temperature and sets the
> trip points.
I will remove the save and restore function.
>
>> +
>> +static SIMPLE_DEV_PM_OPS(loongson2_thermal_pm_ops,
>> +			 loongson2_thermal_suspend, loongson2_thermal_resume);
>> +
>> +static struct platform_driver loongson2_thermal_driver = {
>> +	.driver = {
>> +		.name		= "loongson2_thermal",
>> +		.pm = &loongson2_thermal_pm_ops,
>> +		.of_match_table = of_loongson2_thermal_match,
>> +	},
>> +	.probe	= loongson2_thermal_probe,
>> +	.remove	= loongson2_thermal_remove,
>> +};
>> +module_platform_driver(loongson2_thermal_driver);
>> +
>> +MODULE_DESCRIPTION("Loongson2 thermal driver");
>> +MODULE_LICENSE("GPL");
>> -- 
>> 2.31.1
>>

Re: [PATCH v12 1/2] thermal: loongson-2: add thermal management support

[Daniel Lezcano]

On Wed, Feb 08, 2023 at 11:13:33AM +0800, zhuyinbo wrote:

[ ... ]

> > > +struct loongson2_thermal_data {
> > > +	struct thermal_zone_device *tzd;
> > 'tzd' won't be needed after taking into account the comments
> 
> The 'tzd' element is needed,  because the thermal_zone_device_update need
> pass a data->tzd element.
> 
> static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
> {
>         struct loongson2_thermal_data *data = dev;
> 
>         thermal_zone_device_update(data->tzd,
>                                    THERMAL_EVENT_UNSPECIFIED);
>         enable_irq(data->irq);
> 
>         return IRQ_HANDLED;
> }

After taking into account all the comments, enabled_irq() won't be
called, so 'data' won't be needed. 'tzd' will be passed to
devm_request_threaded_irq() instead of 'data'.

As loongson2_thermal_irq_thread() is the only place where 'tzd' is
needed and 'tzd' being local to the call site of
thermal_zone_device_register() and devm_request_threaded_irq(), there
is no need to store the pointer in the 'data' structure.

> > 
> > > +	int irq;
> > 'irq' won't be needed after taking into account the comments
> I will drop it.
> > > +	int id;
> > > +	void __iomem *regs;
> > > +	struct platform_device *pdev;
> > 'pdev' is not needed
> I will drop it.
> > 
> > > +	u16 ctrl_low_val;
> > > +	u16 ctrl_hi_val;
> > Those fields won't be needed after taking into account the comments
> I will drop it.
> > > +};
> > > +
> > > +static int loongson2_thermal_set(struct loongson2_thermal_data *data,
> > > +					int low, int high, bool enable)
> > > +{
> > > +	u64 reg_ctrl = 0;
> > > +	int reg_off = data->id * 2;
> > > +
> > > +	if (low > high)
> > > +		return -EINVAL;
> > > +
> > > +	low = max(low, -100);
> > > +	high = min(high, 155);

Documentation says -40, 125

> > > +	low += 100;
> > > +	high += 100;
> > Why are those values added to the low and high ? Did you mean low += 0x100 ?
> > 
> > Mind to describe a bit the register layout?
> 
> node(cpu) temp = Thens0_out -100,
> 
> low and high is record node temp, so low and high need add '100' as
> Thens0_out.

If I refer to the documentation it is a raw value converted from
centigrade. The function has degree.

So it should be:

temp_deci = temp_milli / 10

raw = temp_to_raw(temp_deci);

-> temp_to_raw to be determined from temp = (raw * 731) / 0x4000 - 273

[ ... ]

> > > +static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
> > > +{
> > > +	u32 reg_val;
> > > +	struct loongson2_thermal_data *data = tz->devdata;
> > > +
> > > +	reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
> > > +	*temp = ((reg_val & 0xff) - 100) * 1000;
> > Why '-100' ?
> > 
> > Is the unit returned 'degrees' ?
> 
> node(cpu) temp = Thens0_out -100,
> 
> Here we need to get a node temp.

If I refer to the Loongson-3A5000 manual and assuming it is the right
one, the documentation says:

Temperature = Thens0_out * 731 / 0x4000 - 273

The unit is centigrade.

[ ... ]

> > > +	writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
> > > +
> > > +	loongson2_thermal_set(data, 0, 0, false);
> > It would be nicer to use a reset line if it is available
> sorry, I don't get your meaning. Please describe more details about 'reset
> line'.

After a reset, the thermal controller should be in default state and the interrupt
flag cleared.

One example:

[1] https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git/tree/arch/arm64/boot/dts/nvidia/tegra210.dtsi#n1560
[2] https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git/tree/drivers/thermal/tegra/soctherm.c#n2169

Then search in the driver for:
     reset_control_assert(reset);
     reset_control_deassert(reset);


[ ... ]

Thanks

  -- Daniel

-- 

 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

Re: [PATCH v12 1/2] thermal: loongson-2: add thermal management support

[zhuyinbo]

在 2023/2/8 下午6:49, Daniel Lezcano 写道:
> On Wed, Feb 08, 2023 at 11:13:33AM +0800, zhuyinbo wrote:
>
> [ ... ]
>
>>>> +struct loongson2_thermal_data {
>>>> +	struct thermal_zone_device *tzd;
>>> 'tzd' won't be needed after taking into account the comments
>> The 'tzd' element is needed,  because the thermal_zone_device_update need
>> pass a data->tzd element.
>>
>> static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
>> {
>>          struct loongson2_thermal_data *data = dev;
>>
>>          thermal_zone_device_update(data->tzd,
>>                                     THERMAL_EVENT_UNSPECIFIED);
>>          enable_irq(data->irq);
>>
>>          return IRQ_HANDLED;
>> }
> After taking into account all the comments, enabled_irq() won't be
> called, so 'data' won't be needed. 'tzd' will be passed to
> devm_request_threaded_irq() instead of 'data'.
>
> As loongson2_thermal_irq_thread() is the only place where 'tzd' is
> needed and 'tzd' being local to the call site of
> thermal_zone_device_register() and devm_request_threaded_irq(), there
> is no need to store the pointer in the 'data' structure.

okay, I got it. I will remove tzd element in data struct.

>
>>>> +	int irq;
>>> 'irq' won't be needed after taking into account the comments
>> I will drop it.
>>>> +	int id;
>>>> +	void __iomem *regs;
>>>> +	struct platform_device *pdev;
>>> 'pdev' is not needed
>> I will drop it.
>>>> +	u16 ctrl_low_val;
>>>> +	u16 ctrl_hi_val;
>>> Those fields won't be needed after taking into account the comments
>> I will drop it.
>>>> +};
>>>> +
>>>> +static int loongson2_thermal_set(struct loongson2_thermal_data *data,
>>>> +					int low, int high, bool enable)
>>>> +{
>>>> +	u64 reg_ctrl = 0;
>>>> +	int reg_off = data->id * 2;
>>>> +
>>>> +	if (low > high)
>>>> +		return -EINVAL;
>>>> +
>>>> +	low = max(low, -100);
>>>> +	high = min(high, 155);
> Documentation says -40, 125
My previous calculation is to consider that the range of 8bit 
representation is 0 to 255,
and node (cpu) temp=Thens0_ out -100, So the temperature range is 0-100 
~ 255-100, and this
range includes -40~125.  In fact, the range described in the manual is - 
40~125, I will
adop it.
>
>>>> +	low += 100;
>>>> +	high += 100;
>>> Why are those values added to the low and high ? Did you mean low += 0x100 ?
>>>
>>> Mind to describe a bit the register layout?
>> node(cpu) temp = Thens0_out -100,
>>
>> low and high is record node temp, so low and high need add '100' as
>> Thens0_out.
> If I refer to the documentation it is a raw value converted from
> centigrade. The function has degree.
>
> So it should be:
>
> temp_deci = temp_milli / 10
>
> raw = temp_to_raw(temp_deci);
>
> -> temp_to_raw to be determined from temp = (raw * 731) / 0x4000 - 273
>
> [ ... ]
I have review the 3a5000 datasheet,  what you said is right about 
3a5000, but in 2k1000 datasheet,

the calculation of temperature is follows:

Temperature = Thens0_out - 100
  
get_temp return value is (Temperature * 1000) and set_trips is (value /1000) in 2k1000.
I don't find a caculate about "temp_deci = temp_milli / 10" . Are you talking about "
temp_deci = temp_milli / 1000" in set_trips?

>
>>>> +static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
>>>> +{
>>>> +	u32 reg_val;
>>>> +	struct loongson2_thermal_data *data = tz->devdata;
>>>> +
>>>> +	reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
>>>> +	*temp = ((reg_val & 0xff) - 100) * 1000;
>>> Why '-100' ?
>>>
>>> Is the unit returned 'degrees' ?
>> node(cpu) temp = Thens0_out -100,
>>
>> Here we need to get a node temp.
> If I refer to the Loongson-3A5000 manual and assuming it is the right
> one, the documentation says:
>
> Temperature = Thens0_out * 731 / 0x4000 - 273
>
> The unit is centigrade.
>
> [ ... ]

Yes, 3a5000 is what you said, but 2k1000 is calculated as follows:

Temperature = Thens0_out - 100
>
>>>> +	writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
>>>> +
>>>> +	loongson2_thermal_set(data, 0, 0, false);
>>> It would be nicer to use a reset line if it is available
>> sorry, I don't get your meaning. Please describe more details about 'reset
>> line'.
> After a reset, the thermal controller should be in default state and the interrupt
> flag cleared.
>
> One example:
>
> [1] https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git/tree/arch/arm64/boot/dts/nvidia/tegra210.dtsi#n1560
> [2] https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git/tree/drivers/thermal/tegra/soctherm.c#n2169
>
> Then search in the driver for:
>       reset_control_assert(reset);
>       reset_control_deassert(reset);
>
>
> [ ... ]
>
> Thanks
>
>    -- Daniel
thanks your explicate!   but our platform doesn't support it.
>