[PATCH 00/10] SM6375/PDX225 GPI DMA, QUPs & PMIC peripherals

[PATCH 00/10] SM6375/PDX225 GPI DMA, QUPs & PMIC peripherals

[Konrad Dybcio]

This series adds support for:

- GPI DMA for 6375
- QUP hosts & I2C / SPI controllers for 6375
- pinctrl for SOME (check commit message of 05/10) of ^
- pmk8350 on sid6 (rather sad implementation, check 03/10 commit msg)
- touchscreen & SMD regulators on PDX225 (depends on [1])
- pmic peripherals on PDX225

As well as some necessary binding changes with it.

Patches 1-8 can be applied right away, 9 and 10 depend on:

[1] https://lore.kernel.org/linux-arm-msm/20221109110846.45789-1-konrad.dybcio@linaro.org/T/#t

Konrad Dybcio (10):
  dt-bindings: arm-smmu: Allow up to 3 power-domains
  dt-bindings: dmaengine: qcom: gpi: add compatible for SM6375
  arm64: dts: qcom: Add a device tree for PMK8350 on SID6
  arm64: dts: qcom: sm6375: Add GPI DMA nodes
  arm64: dts: qcom: sm6375: Add pin configs for some QUP configurations
  arm64: dts: qcom: sm6375: Add QUPs and corresponding SPI/I2C hosts
  arm64: dts: qcom: sm6375-pdx225: Enable QUPs & GPI DMA
  arm64: dts: qcom: sm6375-pdx225: Add PMIC peripherals
  arm64: dts: qcom: sm6375-pdx225: Configure SMD RPM regulators
  arm64: dts: qcom: sm6375-pdx225: Configure Samsung touchscreen

 .../devicetree/bindings/dma/qcom,gpi.yaml     |   1 +
 .../devicetree/bindings/iommu/arm,smmu.yaml   |   2 +-
 arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi    |  73 ++++
 .../qcom/sm6375-sony-xperia-murray-pdx225.dts | 251 +++++++++++
 arch/arm64/boot/dts/qcom/sm6375.dtsi          | 389 ++++++++++++++++++
 5 files changed, 715 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi

-- 
2.38.1

[PATCH 01/10] dt-bindings: arm-smmu: Allow up to 3 power-domains

[Konrad Dybcio]

Some SMMUs require that a vote is held on as much as 3 separate PDs
(hello Qualcomm). Allow it in bindings.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 Documentation/devicetree/bindings/iommu/arm,smmu.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.yaml b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
index 9066e6df1ba1..1897d0d4d820 100644
--- a/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
+++ b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
@@ -159,7 +159,7 @@ properties:
           through the TCU's programming interface.
 
   power-domains:
-    maxItems: 1
+    maxItems: 3
 
   nvidia,memory-controller:
     description: |
-- 
2.38.1

[PATCH 01/10] dt-bindings: arm-smmu: Allow up to 3 power-domains

[Konrad Dybcio]

Some SMMUs require that a vote is held on as much as 3 separate PDs
(hello Qualcomm). Allow it in bindings.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 Documentation/devicetree/bindings/iommu/arm,smmu.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.yaml b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
index 9066e6df1ba1..1897d0d4d820 100644
--- a/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
+++ b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
@@ -159,7 +159,7 @@ properties:
           through the TCU's programming interface.
 
   power-domains:
-    maxItems: 1
+    maxItems: 3
 
   nvidia,memory-controller:
     description: |
-- 
2.38.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 01/10] dt-bindings: arm-smmu: Allow up to 3 power-domains

[Rob Herring]

On Wed, 09 Nov 2022 12:12:26 +0100, Konrad Dybcio wrote:
> Some SMMUs require that a vote is held on as much as 3 separate PDs
> (hello Qualcomm). Allow it in bindings.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  Documentation/devicetree/bindings/iommu/arm,smmu.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/iommu/arm,smmu.example.dtb: iommu@d00000: power-domains: [[4294967295, 0]] is too short
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/iommu/arm,smmu.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.

Re: [PATCH 01/10] dt-bindings: arm-smmu: Allow up to 3 power-domains

[Rob Herring]

On Wed, 09 Nov 2022 12:12:26 +0100, Konrad Dybcio wrote:
> Some SMMUs require that a vote is held on as much as 3 separate PDs
> (hello Qualcomm). Allow it in bindings.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  Documentation/devicetree/bindings/iommu/arm,smmu.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/iommu/arm,smmu.example.dtb: iommu@d00000: power-domains: [[4294967295, 0]] is too short
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/iommu/arm,smmu.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 01/10] dt-bindings: arm-smmu: Allow up to 3 power-domains

[Krzysztof Kozlowski]

On 09/11/2022 12:12, Konrad Dybcio wrote:
> Some SMMUs require that a vote is held on as much as 3 separate PDs
> (hello Qualcomm). Allow it in bindings.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  Documentation/devicetree/bindings/iommu/arm,smmu.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.yaml b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
> index 9066e6df1ba1..1897d0d4d820 100644
> --- a/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
> +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
> @@ -159,7 +159,7 @@ properties:
>            through the TCU's programming interface.
>  
>    power-domains:
> -    maxItems: 1
> +    maxItems: 3

This is not correct - you now require 3 power domains everywhere. If you
test the DTS you will notice it.

You need min and max items, plus provably allOf:if:then restricting it
per some variants (if it makes sense... depends which SMMUs need it).

Best regards,
Krzysztof

Re: [PATCH 01/10] dt-bindings: arm-smmu: Allow up to 3 power-domains

[Krzysztof Kozlowski]

On 09/11/2022 12:12, Konrad Dybcio wrote:
> Some SMMUs require that a vote is held on as much as 3 separate PDs
> (hello Qualcomm). Allow it in bindings.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  Documentation/devicetree/bindings/iommu/arm,smmu.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.yaml b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
> index 9066e6df1ba1..1897d0d4d820 100644
> --- a/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
> +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml
> @@ -159,7 +159,7 @@ properties:
>            through the TCU's programming interface.
>  
>    power-domains:
> -    maxItems: 1
> +    maxItems: 3

This is not correct - you now require 3 power domains everywhere. If you
test the DTS you will notice it.

You need min and max items, plus provably allOf:if:then restricting it
per some variants (if it makes sense... depends which SMMUs need it).

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 02/10] dt-bindings: dmaengine: qcom: gpi: add compatible for SM6375

[Konrad Dybcio]

Document the compatible for GPI DMA controller on SM6375 SoC.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 Documentation/devicetree/bindings/dma/qcom,gpi.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/dma/qcom,gpi.yaml b/Documentation/devicetree/bindings/dma/qcom,gpi.yaml
index 232895fa1d8d..e7ba1c47a88e 100644
--- a/Documentation/devicetree/bindings/dma/qcom,gpi.yaml
+++ b/Documentation/devicetree/bindings/dma/qcom,gpi.yaml
@@ -26,6 +26,7 @@ properties:
           - enum:
               - qcom,sc7280-gpi-dma
               - qcom,sm6115-gpi-dma
+              - qcom,sm6375-gpi-dma
               - qcom,sm8350-gpi-dma
               - qcom,sm8450-gpi-dma
           - const: qcom,sm6350-gpi-dma
-- 
2.38.1

Re: [PATCH 02/10] dt-bindings: dmaengine: qcom: gpi: add compatible for SM6375

[Krzysztof Kozlowski]

On 09/11/2022 12:12, Konrad Dybcio wrote:
> Document the compatible for GPI DMA controller on SM6375 SoC.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  Documentation/devicetree/bindings/dma/qcom,gpi.yaml | 1 +
>  1 file changed, 1 insertion(+)

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 02/10] dt-bindings: dmaengine: qcom: gpi: add compatible for SM6375

[Vinod Koul]

On 09-11-22, 12:12, Konrad Dybcio wrote:
> Document the compatible for GPI DMA controller on SM6375 SoC.

Applied, thanks

-- 
~Vinod

[PATCH 03/10] arm64: dts: qcom: Add a device tree for PMK8350 on SID6

[Konrad Dybcio]

PMK8350 is shipped on SID6 with some SoCs, for example with SM6375.
Add a DT with the SID changed to allow it to work.

Unfortunately, the entire DT needs to be copied even if the diff is
very little, as the node names are not unique. Including pm6125 and
pmk8350 together for example, would make pmk8350 overwrite the pm6125
node, as both are defined as 'pmic@0'.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi | 73 ++++++++++++++++++++++
 1 file changed, 73 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi b/arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi
new file mode 100644
index 000000000000..00390f8b9c97
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmk8350: pmic@6 {
+		compatible = "qcom,pmk8350", "qcom,spmi-pmic";
+		reg = <0x6 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmk8350_pon: pon@1300 {
+			compatible = "qcom,pm8998-pon";
+			reg = <0x1300>;
+
+			pon_pwrkey: pwrkey {
+				compatible = "qcom,pmk8350-pwrkey";
+				interrupts = <0x6 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+				linux,code = <KEY_POWER>;
+				status = "disabled";
+			};
+
+			pon_resin: resin {
+				compatible = "qcom,pmk8350-resin";
+				interrupts = <0x6 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
+				status = "disabled";
+			};
+		};
+
+		pmk8350_vadc: adc@3100 {
+			compatible = "qcom,spmi-adc7";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <0x6 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#io-channel-cells = <1>;
+		};
+
+		pmk8350_adc_tm: adc-tm@3400 {
+			compatible = "qcom,adc-tm7";
+			reg = <0x3400>;
+			interrupts = <0x6 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#thermal-sensor-cells = <1>;
+			status = "disabled";
+		};
+
+		pmk8350_rtc: rtc@6100 {
+			compatible = "qcom,pmk8350-rtc";
+			reg = <0x6100>, <0x6200>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x6 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		pmk8350_gpios: gpio@b000 {
+			compatible = "qcom,pmk8350-gpio", "qcom,spmi-gpio";
+			reg = <0xb000>;
+			gpio-controller;
+			gpio-ranges = <&pmk8350_gpios 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
-- 
2.38.1

Re: [PATCH 03/10] arm64: dts: qcom: Add a device tree for PMK8350 on SID6

[Bjorn Andersson]

On Wed, Nov 09, 2022 at 12:12:28PM +0100, Konrad Dybcio wrote:
> PMK8350 is shipped on SID6 with some SoCs, for example with SM6375.
> Add a DT with the SID changed to allow it to work.
> 
> Unfortunately, the entire DT needs to be copied even if the diff is
> very little, as the node names are not unique. Including pm6125 and
> pmk8350 together for example, would make pmk8350 overwrite the pm6125
> node, as both are defined as 'pmic@0'.
> 

This seems to work in this case, but we have the same situation in other
places where the labels just don't add up with the schematics.

That's why I ended up just defining all the pmics in sc8280xp-pmics.dtsi
and then the separate set in sa8295p-adp.dts.

Regards,
Bjorn

> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi | 73 ++++++++++++++++++++++
>  1 file changed, 73 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi b/arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi
> new file mode 100644
> index 000000000000..00390f8b9c97
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi
> @@ -0,0 +1,73 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +&spmi_bus {
> +	pmk8350: pmic@6 {
> +		compatible = "qcom,pmk8350", "qcom,spmi-pmic";
> +		reg = <0x6 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pmk8350_pon: pon@1300 {
> +			compatible = "qcom,pm8998-pon";
> +			reg = <0x1300>;
> +
> +			pon_pwrkey: pwrkey {
> +				compatible = "qcom,pmk8350-pwrkey";
> +				interrupts = <0x6 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
> +				linux,code = <KEY_POWER>;
> +				status = "disabled";
> +			};
> +
> +			pon_resin: resin {
> +				compatible = "qcom,pmk8350-resin";
> +				interrupts = <0x6 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		pmk8350_vadc: adc@3100 {
> +			compatible = "qcom,spmi-adc7";
> +			reg = <0x3100>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			interrupts = <0x6 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> +			#io-channel-cells = <1>;
> +		};
> +
> +		pmk8350_adc_tm: adc-tm@3400 {
> +			compatible = "qcom,adc-tm7";
> +			reg = <0x3400>;
> +			interrupts = <0x6 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			#thermal-sensor-cells = <1>;
> +			status = "disabled";
> +		};
> +
> +		pmk8350_rtc: rtc@6100 {
> +			compatible = "qcom,pmk8350-rtc";
> +			reg = <0x6100>, <0x6200>;
> +			reg-names = "rtc", "alarm";
> +			interrupts = <0x6 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
> +			status = "disabled";
> +		};
> +
> +		pmk8350_gpios: gpio@b000 {
> +			compatible = "qcom,pmk8350-gpio", "qcom,spmi-gpio";
> +			reg = <0xb000>;
> +			gpio-controller;
> +			gpio-ranges = <&pmk8350_gpios 0 0 4>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +};
> -- 
> 2.38.1
> 

Re: [PATCH 03/10] arm64: dts: qcom: Add a device tree for PMK8350 on SID6

[Dmitry Baryshkov]

On Wed, 9 Nov 2022 at 14:12, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
> PMK8350 is shipped on SID6 with some SoCs, for example with SM6375.
> Add a DT with the SID changed to allow it to work.
>
> Unfortunately, the entire DT needs to be copied even if the diff is
> very little, as the node names are not unique. Including pm6125 and
> pmk8350 together for example, would make pmk8350 overwrite the pm6125
> node, as both are defined as 'pmic@0'.
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi | 73 ++++++++++++++++++++++
>  1 file changed, 73 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi

Just to throw my 2c. If I was doing this myself, I'd allow pmk8350 to
receive external SID using the cpp #define (And to default to 0 if one
didn't use it).




-- 
With best wishes
Dmitry

Re: [PATCH 03/10] arm64: dts: qcom: Add a device tree for PMK8350 on SID6

[Konrad Dybcio]

On 10/11/2022 10:12, Dmitry Baryshkov wrote:
> On Wed, 9 Nov 2022 at 14:12, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>
>> PMK8350 is shipped on SID6 with some SoCs, for example with SM6375.
>> Add a DT with the SID changed to allow it to work.
>>
>> Unfortunately, the entire DT needs to be copied even if the diff is
>> very little, as the node names are not unique. Including pm6125 and
>> pmk8350 together for example, would make pmk8350 overwrite the pm6125
>> node, as both are defined as 'pmic@0'.
>>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>> ---
>>   arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi | 73 ++++++++++++++++++++++
>>   1 file changed, 73 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi
> 
> Just to throw my 2c. If I was doing this myself, I'd allow pmk8350 to
> receive external SID using the cpp #define (And to default to 0 if one
> didn't use it).
Hmm.. that's probably the least duplicative approach, but I'm not sure I
want to see #ifdefs in DTs..

Konrad
> 
> 
> 
> 

Re: [PATCH 03/10] arm64: dts: qcom: Add a device tree for PMK8350 on SID6

[Bjorn Andersson]

On Thu, Nov 10, 2022 at 12:12:19PM +0300, Dmitry Baryshkov wrote:
> On Wed, 9 Nov 2022 at 14:12, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
> >
> > PMK8350 is shipped on SID6 with some SoCs, for example with SM6375.
> > Add a DT with the SID changed to allow it to work.
> >
> > Unfortunately, the entire DT needs to be copied even if the diff is
> > very little, as the node names are not unique. Including pm6125 and
> > pmk8350 together for example, would make pmk8350 overwrite the pm6125
> > node, as both are defined as 'pmic@0'.
> >
> > Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi | 73 ++++++++++++++++++++++
> >  1 file changed, 73 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi
> 
> Just to throw my 2c. If I was doing this myself, I'd allow pmk8350 to
> receive external SID using the cpp #define (And to default to 0 if one
> didn't use it).
> 

I attempted this, for my four PM8150s in the SA8295P ADP.

Unfortunately it became quite messy due to the multiple SIDs, the fact
that all interrupts specifiers contains the SID, that the labels became
unreadable and the fact that there are label-based references within
each pmic.

But I like the idea!

Regards,
Bjorn

[PATCH 04/10] arm64: dts: qcom: sm6375: Add GPI DMA nodes

[Konrad Dybcio]

Add nodes for GPI DMA hosts on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm6375.dtsi | 40 ++++++++++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6375.dtsi b/arch/arm64/boot/dts/qcom/sm6375.dtsi
index 9b1a497e5ca7..62a64dd731a0 100644
--- a/arch/arm64/boot/dts/qcom/sm6375.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6375.dtsi
@@ -567,6 +567,46 @@ rpm_msg_ram: sram@45f0000 {
 			reg = <0 0x045f0000 0 0x7000>;
 		};
 
+		gpi_dma0: dma-controller@4a00000 {
+			compatible = "qcom,sm6375-gpi-dma", "qcom,sm6350-gpi-dma";
+			reg = <0 0x04a00000 0 0x60000>;
+			interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <10>;
+			dma-channel-mask = <0x1f>;
+			iommus = <&apps_smmu 0x16 0x0>;
+			#dma-cells = <3>;
+			status = "disabled";
+		};
+
+		gpi_dma1: dma-controller@4c00000 {
+			compatible = "qcom,sm6375-gpi-dma", "qcom,sm6350-gpi-dma";
+			reg = <0 0x04c00000 0 0x60000>;
+			interrupts = <GIC_SPI 497 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 498 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 499 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 500 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 501 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 502 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 503 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 504 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 505 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <10>;
+			dma-channel-mask = <0x1f>;
+			iommus = <&apps_smmu 0xd6 0x0>;
+			#dma-cells = <3>;
+			status = "disabled";
+		};
+
 		usb_1: usb@4ef8800 {
 			compatible = "qcom,sm6375-dwc3", "qcom,dwc3";
 			reg = <0 0x04ef8800 0 0x400>;
-- 
2.38.1

[PATCH 05/10] arm64: dts: qcom: sm6375: Add pin configs for some QUP configurations

[Konrad Dybcio]

Add the pin setup for SPI/I2C configurations that are supported
downstream. I can guesstimate the correct settings for other buses,
but:

- I have no hardware to test it on
- Some QUPs are straight up missing pin funcs in TLMM
- Vendors probably didn't really care and used whatever was there in
the reference design and BSP - should any other be used, they can be
configured at a later time

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm6375.dtsi | 43 ++++++++++++++++++++++++++++
 1 file changed, 43 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6375.dtsi b/arch/arm64/boot/dts/qcom/sm6375.dtsi
index 62a64dd731a0..952156891476 100644
--- a/arch/arm64/boot/dts/qcom/sm6375.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6375.dtsi
@@ -519,6 +519,49 @@ tlmm: pinctrl@500000 {
 			gpio-controller;
 			#interrupt-cells = <2>;
 			#gpio-cells = <2>;
+
+			qup_i2c0_default: qup-i2c0-default-state {
+				pins = "gpio0", "gpio1";
+				function = "qup00";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c1_default: qup-i2c1-default-state {
+				pins = "gpio61", "gpio62";
+				function = "qup01";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c2_default: qup-i2c2-default-state {
+				pins = "gpio45", "gpio46";
+				function = "qup02";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c8_default: qup-i2c8-default-state {
+				pins = "gpio19", "gpio20";
+				/* TLMM, GCC and vendor DT all have different indices.. */
+				function = "qup12";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c10_default: qup-i2c10-default-state {
+				pins = "gpio4", "gpio5";
+				function = "qup10";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_spi0_default: qup-spi0-default-state {
+				pins = "gpio0", "gpio1", "gpio2", "gpio3";
+				function = "qup00";
+				drive-strength = <6>;
+				bias-disable;
+			};
 		};
 
 		gcc: clock-controller@1400000 {
-- 
2.38.1

Re: [PATCH 05/10] arm64: dts: qcom: sm6375: Add pin configs for some QUP configurations

[Krzysztof Kozlowski]

On 09/11/2022 12:12, Konrad Dybcio wrote:
> Add the pin setup for SPI/I2C configurations that are supported
> downstream. I can guesstimate the correct settings for other buses,
> but:
> 
> - I have no hardware to test it on
> - Some QUPs are straight up missing pin funcs in TLMM
> - Vendors probably didn't really care and used whatever was there in
> the reference design and BSP - should any other be used, they can be
> configured at a later time
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm6375.dtsi | 43 ++++++++


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

[PATCH 06/10] arm64: dts: qcom: sm6375: Add QUPs and corresponding SPI/I2C hosts

[Konrad Dybcio]

Add necessary nodes to support various QUP configurations. Note that:

- QUP3/4/5 and 11 are straight up missing
- There may be more QUPs physically on the SoC that work perfectly
fine, but Qualcomm decided not to expose them on the downstream kernel
- Many are missing pinctrls, as there are both missing pin funcs in
the TLMM driver and missing configuration settings (though they are
possible to guesstimate quite easily)

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm6375.dtsi | 306 +++++++++++++++++++++++++++
 1 file changed, 306 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6375.dtsi b/arch/arm64/boot/dts/qcom/sm6375.dtsi
index 952156891476..6adffd927a8e 100644
--- a/arch/arm64/boot/dts/qcom/sm6375.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6375.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/clock/qcom,rpmcc.h>
 #include <dt-bindings/clock/qcom,sm6375-gcc.h>
+#include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
@@ -317,6 +318,25 @@ CLUSTER_PD: cpu-cluster0 {
 		};
 	};
 
+	qup_opp_table: opp-table-qup {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmpd_opp_low_svs>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			required-opps = <&rpmpd_opp_svs>;
+		};
+
+		opp-128000000 {
+			opp-hz = /bits/ 64 <128000000>;
+			required-opps = <&rpmpd_opp_nom>;
+		};
+	};
+
 	reserved_memory: reserved-memory {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -630,6 +650,125 @@ gpi_dma0: dma-controller@4a00000 {
 			status = "disabled";
 		};
 
+		qupv3_id_0: geniqup@4ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x04ac0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x3 0x0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c0: i2c@4a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x04a80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_default>;
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi0: spi@4a80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x04a80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_default>;
+				power-domains = <&rpmpd SM6375_VDDCX>;
+				operating-points-v2 = <&qup_opp_table>;
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@4a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x04a84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_default>;
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi1: spi@4a84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x04a84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmpd SM6375_VDDCX>;
+				operating-points-v2 = <&qup_opp_table>;
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@4a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x04a88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_default>;
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi2: spi@4a88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x04a88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmpd SM6375_VDDCX>;
+				operating-points-v2 = <&qup_opp_table>;
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			/*
+			 * As per GCC, QUP3/4/5/11 also exist, but are not even defined downstream.
+			 * There is a comment in the included DTSI of another SoC saying that they
+			 * are not "bolled out" (probably meaning not routed to solder balls)
+			 * TLMM driver however, suggests there are as many as 15 QUPs in total!
+			 * Most of which don't even have pin configurations for.. Sad stuff!
+			 */
+		};
+
 		gpi_dma1: dma-controller@4c00000 {
 			compatible = "qcom,sm6375-gpi-dma", "qcom,sm6350-gpi-dma";
 			reg = <0 0x04c00000 0 0x60000>;
@@ -650,6 +789,173 @@ gpi_dma1: dma-controller@4c00000 {
 			status = "disabled";
 		};
 
+		qupv3_id_1: geniqup@4cc0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x04cc0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			iommus = <&apps_smmu 0xc3 0x0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c6: i2c@4c80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x04c80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi6: spi@4c80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x04c80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmpd SM6375_VDDCX>;
+				operating-points-v2 = <&qup_opp_table>;
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c7: i2c@4c84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x04c84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				interrupts = <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi7: spi@4c84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x04c84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				interrupts = <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmpd SM6375_VDDCX>;
+				operating-points-v2 = <&qup_opp_table>;
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c8: i2c@4c88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x04c88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				interrupts = <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c8_default>;
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi8: spi@4c88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x04c88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				interrupts = <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmpd SM6375_VDDCX>;
+				operating-points-v2 = <&qup_opp_table>;
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c9: i2c@4c8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x04c8c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				interrupts = <GIC_SPI 510 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi9: spi@4c8c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x04c8c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				interrupts = <GIC_SPI 510 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmpd SM6375_VDDCX>;
+				operating-points-v2 = <&qup_opp_table>;
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c10: i2c@4c90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x04c90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				interrupts = <GIC_SPI 511 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c10_default>;
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi10: spi@4c90000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x04c90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				interrupts = <GIC_SPI 511 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmpd SM6375_VDDCX>;
+				operating-points-v2 = <&qup_opp_table>;
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
 		usb_1: usb@4ef8800 {
 			compatible = "qcom,sm6375-dwc3", "qcom,dwc3";
 			reg = <0 0x04ef8800 0 0x400>;
-- 
2.38.1

[PATCH 07/10] arm64: dts: qcom: sm6375-pdx225: Enable QUPs & GPI DMA

[Konrad Dybcio]

Enable QUPs & GPI DMA on the Xperia 10 IV.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../qcom/sm6375-sony-xperia-murray-pdx225.dts    | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts b/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
index 450d4a557df1..6a0f4c0bf7ad 100644
--- a/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
+++ b/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
@@ -65,6 +65,22 @@ vph_pwr: vph-pwr-regulator {
 	};
 };
 
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <13 4>;
 };
-- 
2.38.1

[PATCH 08/10] arm64: dts: qcom: sm6375-pdx225: Add PMIC peripherals

[Konrad Dybcio]

Add and enable PMIC peripherals for PM6125, PMR735a and PMK8350 on
the Xperia 10 IV.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../qcom/sm6375-sony-xperia-murray-pdx225.dts | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts b/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
index 6a0f4c0bf7ad..d34b4b96e1b9 100644
--- a/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
+++ b/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
@@ -7,8 +7,13 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include "sm6375.dtsi"
+#include "pm6125.dtsi"
+#include "pmk8350_sid6.dtsi"
 #include "pmr735a.dtsi"
 
+/* PM6125 PON is used and we can't have duplicate labels */
+/delete-node/ &pmk8350_pon;
+
 / {
 	model = "Sony Xperia 10 IV";
 	compatible = "sony,pdx225", "qcom,sm6375";
@@ -73,6 +78,23 @@ &gpi_dma1 {
 	status = "okay";
 };
 
+&pmk8350_adc_tm {
+	status = "okay";
+};
+
+&pmk8350_rtc {
+	status = "okay";
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEUP>;
+	status = "okay";
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
-- 
2.38.1

[PATCH 09/10] arm64: dts: qcom: sm6375-pdx225: Configure SMD RPM regulators

[Konrad Dybcio]

Configure regulators present on the Xperia 10 IV that are reachable
via SMD RPM.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../qcom/sm6375-sony-xperia-murray-pdx225.dts | 182 ++++++++++++++++++
 1 file changed, 182 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts b/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
index d34b4b96e1b9..17094e588a3a 100644
--- a/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
+++ b/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
@@ -95,6 +95,188 @@ &pon_resin {
 	status = "okay";
 };
 
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm6125-regulators";
+
+		pm6125_s5: s5 {
+			regulator-min-microvolt = <382000>;
+			regulator-max-microvolt = <1120000>;
+		};
+
+		pm6125_s6: s6 {
+			regulator-min-microvolt = <320000>;
+			regulator-max-microvolt = <1374000>;
+		};
+
+		pm6125_s7: s7 {
+			regulator-min-microvolt = <1574000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		/*
+		 * S8 is VDD_GFX
+		 * L1 is VDD_LPI_CX
+		 */
+
+		pm6125_l2: l2 {
+			regulator-min-microvolt = <1170000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		pm6125_l3: l3 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm6125_l4: l4 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm6125_l5: l5 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3050000>;
+		};
+
+		pm6125_l6: l6 {
+			regulator-min-microvolt = <1080000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		pm6125_l7: l7 {
+			regulator-min-microvolt = <720000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm6125_l8: l8 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		pm6125_l9: l9 {
+			regulator-min-microvolt = <1504000>;
+			regulator-max-microvolt = <2000000>;
+		};
+
+		pm6125_l10: l10 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+		};
+
+		pm6125_l11: l11 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+		};
+
+		pm6125_l12: l12 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <2000000>;
+		};
+
+		pm6125_l13: l13 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <1980000>;
+		};
+
+		pm6125_l14: l14 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+		};
+
+		pm6125_l15: l15 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3544000>;
+		};
+
+		pm6125_l16: l16 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+		};
+
+		/* L17 is VDD_LPI_MX */
+
+		pm6125_l18: l18 {
+			regulator-min-microvolt = <830000>;
+			regulator-max-microvolt = <920000>;
+		};
+
+		pm6125_l19: l19 {
+			regulator-min-microvolt = <1624000>;
+			regulator-max-microvolt = <3304000>;
+		};
+
+		pm6125_l20: l20 {
+			regulator-min-microvolt = <1624000>;
+			regulator-max-microvolt = <3304000>;
+		};
+
+		pm6125_l21: l21 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+		};
+
+		pm6125_l22: l22 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <3544000>;
+		};
+
+		pm6125_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+		};
+
+		pm6125_l24: l24 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <3544000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pmr735a-regulators";
+
+		/*
+		 * S1 is VDD_MX
+		 * S2 is VDD_CX
+		 */
+
+		pmr735a_l1: l1 {
+			regulator-min-microvolt = <570000>;
+			regulator-max-microvolt = <650000>;
+		};
+
+		pmr735a_l2: l2 {
+			regulator-min-microvolt = <352000>;
+			regulator-max-microvolt = <796000>;
+		};
+
+		pmr735a_l3: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pmr735a_l4: l4 {
+			regulator-min-microvolt = <1504000>;
+			regulator-max-microvolt = <2000000>;
+		};
+
+		pmr735a_l5: l5 {
+			regulator-min-microvolt = <751000>;
+			regulator-max-microvolt = <824000>;
+		};
+
+		pmr735a_l6: l6 {
+			regulator-min-microvolt = <504000>;
+			regulator-max-microvolt = <868000>;
+		};
+
+		pmr735a_l7: l7 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+		};
+	};
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
-- 
2.38.1

[PATCH 10/10] arm64: dts: qcom: sm6375-pdx225: Configure Samsung touchscreen

[Konrad Dybcio]

Add a pretty bog-standard-for-Xperias-for-the-past-3-years
touchscreen setup.

The OEM that built the Xperia 10 IV for SONY decided to use some
kind of a GPIO regulator that needs to be enabled at all times
for both the touch panel and the display panel to function.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../qcom/sm6375-sony-xperia-murray-pdx225.dts | 31 +++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts b/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
index 17094e588a3a..33083f18755b 100644
--- a/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
+++ b/arch/arm64/boot/dts/qcom/sm6375-sony-xperia-murray-pdx225.dts
@@ -78,6 +78,23 @@ &gpi_dma1 {
 	status = "okay";
 };
 
+&i2c8 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	touchscreen@48 {
+		compatible = "samsung,s6sy761";
+		reg = <0x48>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <22 0x2008>;
+
+		vdd-supply = <&pm6125_l13>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_default &ts_avdd_default>;
+	};
+};
+
 &pmk8350_adc_tm {
 	status = "okay";
 };
@@ -287,6 +304,20 @@ &qupv3_id_1 {
 
 &tlmm {
 	gpio-reserved-ranges = <13 4>;
+
+	ts_int_default: ts-int-default-state {
+		pins = "gpio22";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	ts_avdd_default: ts-avdd-default-state {
+		pins = "gpio59";
+		function = "gpio";
+		drive-strength = <8>;
+		output-high;
+	};
 };
 
 &usb_1 {
-- 
2.38.1