* [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-02 3:05 ` Wenyou Yang
0 siblings, 0 replies; 15+ messages in thread
From: Wenyou Yang @ 2016-11-02 3:05 UTC (permalink / raw)
To: Nicolas Ferre, Alexandre Belloni, Russell King, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Cc: linux-kernel, Wenyou Yang, devicetree, linux-arm-kernel, Wenyou Yang
The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
some power rail. Its main purpose is used to measure the power
consumption.
The difference of the sama5d36ek CMP dts from sama5d36ek dts
is listed as below.
1. The USB host nodes are removed, that is, the USB host is disabled.
2. The gpio_keys node is added to wake up from the sleep.
3. The LCD isn't supported due to the pins for LCD are conflicted
with gpio_keys.
4. The adc0 node support the pinctrl sleep state to fix the over
consumption on VDDANA.
As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
is disabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
---
Changes in v2:
- Add the pinctrl sleep state for adc0 node to fix the over
consumption on VDDANA.
- Improve the commit log.
arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
3 files changed, 482 insertions(+)
create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
new file mode 100644
index 0000000..fd6bcd6
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
@@ -0,0 +1,51 @@
+/*
+ * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+#include "sama5d3xmb_cmp.dtsi"
+
+/ {
+ model = "Atmel SAMA5D36-EK";
+ compatible = "atmel,sama5d36ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ spi0: spi@f0004000 {
+ status = "okay";
+ };
+
+ ssc0: ssc@f0008000 {
+ status = "okay";
+ };
+
+ can0: can@f000c000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@f0014000 {
+ status = "okay";
+ };
+
+ i2c1: i2c@f0018000 {
+ status = "okay";
+ };
+
+ macb0: ethernet@f0028000 {
+ status = "okay";
+ };
+
+ macb1: ethernet@f802c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ sound {
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
new file mode 100644
index 0000000..77638c3
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
@@ -0,0 +1,166 @@
+/*
+ * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/ {
+ compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ spi0: spi@f0004000 {
+ cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+ };
+
+ macb0: ethernet@f0028000 {
+ phy-mode = "rgmii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioB>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ txen-skew-ps = <800>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <400>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <400>;
+ rxd1-skew-ps = <400>;
+ rxd2-skew-ps = <400>;
+ rxd3-skew-ps = <400>;
+ };
+
+ ethernet-phy@7 {
+ reg = <0x7>;
+ interrupt-parent = <&pioB>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ txen-skew-ps = <800>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <400>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <400>;
+ rxd1-skew-ps = <400>;
+ rxd2-skew-ps = <400>;
+ rxd3-skew-ps = <400>;
+ };
+ };
+
+ i2c1: i2c@f0018000 {
+ pmic: act8865@5b {
+ compatible = "active-semi,act8865";
+ reg = <0x5b>;
+ status = "disabled";
+
+ regulators {
+ vcc_1v8_reg: DCDC_REG1 {
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcc_1v2_reg: DCDC_REG2 {
+ regulator-name = "VCC_1V2";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ };
+
+ vcc_3v3_reg: DCDC_REG3 {
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vddana_reg: LDO_REG1 {
+ regulator-name = "VDDANA";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vddfuse_reg: LDO_REG2 {
+ regulator-name = "FUSE_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+ };
+ };
+ };
+ };
+
+ nand0: nand@60000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+ status = "okay";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader@40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv@c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb@180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ d2 {
+ label = "d2";
+ gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
new file mode 100644
index 0000000..62c6230
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
@@ -0,0 +1,265 @@
+/*
+ * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include "sama5d3xcm_cmp.dtsi"
+
+/ {
+ compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ mmc0: mmc@f0000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ spi0: spi@f0004000 {
+ dmas = <0>, <0>; /* Do not use DMA for spi0 */
+
+ m25p80@0 {
+ compatible = "atmel,at25df321a";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ ssc0: ssc@f0008000 {
+ atmel,clk-from-rk-pin;
+ };
+
+ /*
+ * i2c0 conflicts with ISI:
+ * disable it to allow the use of ISI
+ * can not enable audio when i2c0 disabled
+ */
+ i2c0: i2c@f0014000 {
+ wm8904: wm8904@1a {
+ compatible = "wlf,wm8904";
+ reg = <0x1a>;
+ clocks = <&pck0>;
+ clock-names = "mclk";
+ };
+ };
+
+ i2c1: i2c@f0018000 {
+ ov2640: camera@0x30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+ resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+ /* use pck1 for the master clock of ov2640 */
+ clocks = <&pck1>;
+ clock-names = "xvclk";
+ assigned-clocks = <&pck1>;
+ assigned-clock-rates = <25000000>;
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+ };
+
+ usart1: serial@f0020000 {
+ dmas = <0>, <0>; /* Do not use DMA for usart1 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+ status = "okay";
+ };
+
+ isi: isi@f0034000 {
+ port {
+ isi_0: endpoint {
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ vsync-active = <1>;
+ hsync-active = <1>;
+ };
+ };
+ };
+
+ mmc1: mmc@f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ adc0: adc@f8018000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <
+ &pinctrl_adc0_adtrg
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ >;
+ pinctrl-1 = <
+ &pinctrl_adc0_adtrg_sleep
+ &pinctrl_adc0_ad0_sleep
+ &pinctrl_adc0_ad1_sleep
+ &pinctrl_adc0_ad2_sleep
+ &pinctrl_adc0_ad3_sleep
+ &pinctrl_adc0_ad4_sleep
+ >;
+ status = "okay";
+ };
+
+ macb1: ethernet@f802c000 {
+ phy-mode = "rmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@1 {
+ /*interrupt-parent = <&pioE>;*/
+ /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
+ reg = <1>;
+ };
+ };
+
+ pinctrl@fffff200 {
+ adc0 {
+ pinctrl_adc0_adtrg_sleep: adc0_adtrg_1 {
+ atmel,pins =
+ <AT91_PIOD 19 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD19 GPIO output 0 */
+ };
+ pinctrl_adc0_ad0_sleep: adc0_ad0_1 {
+ atmel,pins =
+ <AT91_PIOD 20 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD20 GPIO output 0 */
+ };
+ pinctrl_adc0_ad1_sleep: adc0_ad1_1 {
+ atmel,pins =
+ <AT91_PIOD 21 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD21 GPIO output 0 */
+ };
+ pinctrl_adc0_ad2_sleep: adc0_ad2_1 {
+ atmel,pins =
+ <AT91_PIOD 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD22 GPIO output 0 */
+ };
+ pinctrl_adc0_ad3_sleep: adc0_ad3_1 {
+ atmel,pins =
+ <AT91_PIOD 23 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD23 GPIO output 0 */
+ };
+ pinctrl_adc0_ad4_sleep: adc0_ad4_1 {
+ atmel,pins =
+ <AT91_PIOD 24 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD24 GPIO output 0 */
+ };
+ };
+
+ board {
+ pinctrl_gpio_keys: gpio_keys {
+ atmel,pins =
+ <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_mmc0_cd: mmc0_cd {
+ atmel,pins =
+ <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
+ };
+
+ pinctrl_mmc1_cd: mmc1_cd {
+ atmel,pins =
+ <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
+ };
+
+ pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+ atmel,pins =
+ <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */
+ };
+
+ pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+ atmel,pins =
+ <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */
+ };
+
+ pinctrl_sensor_reset: sensor_reset-0 {
+ atmel,pins =
+ <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */
+ };
+
+ pinctrl_sensor_power: sensor_power-0 {
+ atmel,pins =
+ <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
+ };
+ };
+ };
+
+ dbgu: serial@ffffee00 {
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+ status = "okay";
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+ };
+
+ usb0: gadget@00500000 {
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+ };
+
+ sound {
+ compatible = "atmel,asoc-wm8904";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+ atmel,model = "wm8904 @ SAMA5D3EK";
+ atmel,audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "IN2L", "Line In Jack",
+ "IN2R", "Line In Jack",
+ "Mic", "MICBIAS",
+ "IN1L", "Mic";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8904>;
+
+ status = "disabled";
+ };
+
+ /* Conflict with LCD pins */
+ gpio_keys {
+ compatible = "gpio-keys";
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ pb_user1 {
+ label = "pb_user1";
+ gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
+ linux,code = <0x100>;
+ gpio-key,wakeup;
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-02 3:05 ` Wenyou Yang
0 siblings, 0 replies; 15+ messages in thread
From: Wenyou Yang @ 2016-11-02 3:05 UTC (permalink / raw)
To: Nicolas Ferre, Alexandre Belloni, Russell King, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Cc: linux-kernel, Wenyou Yang, devicetree, linux-arm-kernel, Wenyou Yang
The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
some power rail. Its main purpose is used to measure the power
consumption.
The difference of the sama5d36ek CMP dts from sama5d36ek dts
is listed as below.
1. The USB host nodes are removed, that is, the USB host is disabled.
2. The gpio_keys node is added to wake up from the sleep.
3. The LCD isn't supported due to the pins for LCD are conflicted
with gpio_keys.
4. The adc0 node support the pinctrl sleep state to fix the over
consumption on VDDANA.
As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
is disabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
---
Changes in v2:
- Add the pinctrl sleep state for adc0 node to fix the over
consumption on VDDANA.
- Improve the commit log.
arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
3 files changed, 482 insertions(+)
create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
new file mode 100644
index 0000000..fd6bcd6
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
@@ -0,0 +1,51 @@
+/*
+ * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+#include "sama5d3xmb_cmp.dtsi"
+
+/ {
+ model = "Atmel SAMA5D36-EK";
+ compatible = "atmel,sama5d36ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ spi0: spi@f0004000 {
+ status = "okay";
+ };
+
+ ssc0: ssc@f0008000 {
+ status = "okay";
+ };
+
+ can0: can@f000c000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@f0014000 {
+ status = "okay";
+ };
+
+ i2c1: i2c@f0018000 {
+ status = "okay";
+ };
+
+ macb0: ethernet@f0028000 {
+ status = "okay";
+ };
+
+ macb1: ethernet@f802c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ sound {
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
new file mode 100644
index 0000000..77638c3
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
@@ -0,0 +1,166 @@
+/*
+ * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/ {
+ compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ spi0: spi@f0004000 {
+ cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+ };
+
+ macb0: ethernet@f0028000 {
+ phy-mode = "rgmii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioB>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ txen-skew-ps = <800>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <400>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <400>;
+ rxd1-skew-ps = <400>;
+ rxd2-skew-ps = <400>;
+ rxd3-skew-ps = <400>;
+ };
+
+ ethernet-phy@7 {
+ reg = <0x7>;
+ interrupt-parent = <&pioB>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ txen-skew-ps = <800>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <400>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <400>;
+ rxd1-skew-ps = <400>;
+ rxd2-skew-ps = <400>;
+ rxd3-skew-ps = <400>;
+ };
+ };
+
+ i2c1: i2c@f0018000 {
+ pmic: act8865@5b {
+ compatible = "active-semi,act8865";
+ reg = <0x5b>;
+ status = "disabled";
+
+ regulators {
+ vcc_1v8_reg: DCDC_REG1 {
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcc_1v2_reg: DCDC_REG2 {
+ regulator-name = "VCC_1V2";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ };
+
+ vcc_3v3_reg: DCDC_REG3 {
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vddana_reg: LDO_REG1 {
+ regulator-name = "VDDANA";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vddfuse_reg: LDO_REG2 {
+ regulator-name = "FUSE_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+ };
+ };
+ };
+ };
+
+ nand0: nand@60000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+ status = "okay";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader@40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv@c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb@180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ d2 {
+ label = "d2";
+ gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
new file mode 100644
index 0000000..62c6230
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
@@ -0,0 +1,265 @@
+/*
+ * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include "sama5d3xcm_cmp.dtsi"
+
+/ {
+ compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ mmc0: mmc@f0000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ spi0: spi@f0004000 {
+ dmas = <0>, <0>; /* Do not use DMA for spi0 */
+
+ m25p80@0 {
+ compatible = "atmel,at25df321a";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ ssc0: ssc@f0008000 {
+ atmel,clk-from-rk-pin;
+ };
+
+ /*
+ * i2c0 conflicts with ISI:
+ * disable it to allow the use of ISI
+ * can not enable audio when i2c0 disabled
+ */
+ i2c0: i2c@f0014000 {
+ wm8904: wm8904@1a {
+ compatible = "wlf,wm8904";
+ reg = <0x1a>;
+ clocks = <&pck0>;
+ clock-names = "mclk";
+ };
+ };
+
+ i2c1: i2c@f0018000 {
+ ov2640: camera@0x30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+ resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+ /* use pck1 for the master clock of ov2640 */
+ clocks = <&pck1>;
+ clock-names = "xvclk";
+ assigned-clocks = <&pck1>;
+ assigned-clock-rates = <25000000>;
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+ };
+
+ usart1: serial@f0020000 {
+ dmas = <0>, <0>; /* Do not use DMA for usart1 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+ status = "okay";
+ };
+
+ isi: isi@f0034000 {
+ port {
+ isi_0: endpoint {
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ vsync-active = <1>;
+ hsync-active = <1>;
+ };
+ };
+ };
+
+ mmc1: mmc@f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ adc0: adc@f8018000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <
+ &pinctrl_adc0_adtrg
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ >;
+ pinctrl-1 = <
+ &pinctrl_adc0_adtrg_sleep
+ &pinctrl_adc0_ad0_sleep
+ &pinctrl_adc0_ad1_sleep
+ &pinctrl_adc0_ad2_sleep
+ &pinctrl_adc0_ad3_sleep
+ &pinctrl_adc0_ad4_sleep
+ >;
+ status = "okay";
+ };
+
+ macb1: ethernet@f802c000 {
+ phy-mode = "rmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@1 {
+ /*interrupt-parent = <&pioE>;*/
+ /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
+ reg = <1>;
+ };
+ };
+
+ pinctrl@fffff200 {
+ adc0 {
+ pinctrl_adc0_adtrg_sleep: adc0_adtrg_1 {
+ atmel,pins =
+ <AT91_PIOD 19 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD19 GPIO output 0 */
+ };
+ pinctrl_adc0_ad0_sleep: adc0_ad0_1 {
+ atmel,pins =
+ <AT91_PIOD 20 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD20 GPIO output 0 */
+ };
+ pinctrl_adc0_ad1_sleep: adc0_ad1_1 {
+ atmel,pins =
+ <AT91_PIOD 21 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD21 GPIO output 0 */
+ };
+ pinctrl_adc0_ad2_sleep: adc0_ad2_1 {
+ atmel,pins =
+ <AT91_PIOD 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD22 GPIO output 0 */
+ };
+ pinctrl_adc0_ad3_sleep: adc0_ad3_1 {
+ atmel,pins =
+ <AT91_PIOD 23 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD23 GPIO output 0 */
+ };
+ pinctrl_adc0_ad4_sleep: adc0_ad4_1 {
+ atmel,pins =
+ <AT91_PIOD 24 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD24 GPIO output 0 */
+ };
+ };
+
+ board {
+ pinctrl_gpio_keys: gpio_keys {
+ atmel,pins =
+ <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_mmc0_cd: mmc0_cd {
+ atmel,pins =
+ <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
+ };
+
+ pinctrl_mmc1_cd: mmc1_cd {
+ atmel,pins =
+ <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
+ };
+
+ pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+ atmel,pins =
+ <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */
+ };
+
+ pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+ atmel,pins =
+ <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */
+ };
+
+ pinctrl_sensor_reset: sensor_reset-0 {
+ atmel,pins =
+ <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */
+ };
+
+ pinctrl_sensor_power: sensor_power-0 {
+ atmel,pins =
+ <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
+ };
+ };
+ };
+
+ dbgu: serial@ffffee00 {
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+ status = "okay";
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+ };
+
+ usb0: gadget@00500000 {
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+ };
+
+ sound {
+ compatible = "atmel,asoc-wm8904";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+ atmel,model = "wm8904 @ SAMA5D3EK";
+ atmel,audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "IN2L", "Line In Jack",
+ "IN2R", "Line In Jack",
+ "Mic", "MICBIAS",
+ "IN1L", "Mic";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8904>;
+
+ status = "disabled";
+ };
+
+ /* Conflict with LCD pins */
+ gpio_keys {
+ compatible = "gpio-keys";
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ pb_user1 {
+ label = "pb_user1";
+ gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
+ linux,code = <0x100>;
+ gpio-key,wakeup;
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-02 3:05 ` Wenyou Yang
0 siblings, 0 replies; 15+ messages in thread
From: Wenyou Yang @ 2016-11-02 3:05 UTC (permalink / raw)
To: linux-arm-kernel
The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
some power rail. Its main purpose is used to measure the power
consumption.
The difference of the sama5d36ek CMP dts from sama5d36ek dts
is listed as below.
1. The USB host nodes are removed, that is, the USB host is disabled.
2. The gpio_keys node is added to wake up from the sleep.
3. The LCD isn't supported due to the pins for LCD are conflicted
with gpio_keys.
4. The adc0 node support the pinctrl sleep state to fix the over
consumption on VDDANA.
As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
is disabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
---
Changes in v2:
- Add the pinctrl sleep state for adc0 node to fix the over
consumption on VDDANA.
- Improve the commit log.
arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
3 files changed, 482 insertions(+)
create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
new file mode 100644
index 0000000..fd6bcd6
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
@@ -0,0 +1,51 @@
+/*
+ * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+#include "sama5d3xmb_cmp.dtsi"
+
+/ {
+ model = "Atmel SAMA5D36-EK";
+ compatible = "atmel,sama5d36ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ spi0: spi at f0004000 {
+ status = "okay";
+ };
+
+ ssc0: ssc at f0008000 {
+ status = "okay";
+ };
+
+ can0: can at f000c000 {
+ status = "okay";
+ };
+
+ i2c0: i2c at f0014000 {
+ status = "okay";
+ };
+
+ i2c1: i2c at f0018000 {
+ status = "okay";
+ };
+
+ macb0: ethernet at f0028000 {
+ status = "okay";
+ };
+
+ macb1: ethernet at f802c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ sound {
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
new file mode 100644
index 0000000..77638c3
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
@@ -0,0 +1,166 @@
+/*
+ * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/ {
+ compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ spi0: spi at f0004000 {
+ cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+ };
+
+ macb0: ethernet at f0028000 {
+ phy-mode = "rgmii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-phy at 1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioB>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ txen-skew-ps = <800>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <400>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <400>;
+ rxd1-skew-ps = <400>;
+ rxd2-skew-ps = <400>;
+ rxd3-skew-ps = <400>;
+ };
+
+ ethernet-phy at 7 {
+ reg = <0x7>;
+ interrupt-parent = <&pioB>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ txen-skew-ps = <800>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <400>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <400>;
+ rxd1-skew-ps = <400>;
+ rxd2-skew-ps = <400>;
+ rxd3-skew-ps = <400>;
+ };
+ };
+
+ i2c1: i2c at f0018000 {
+ pmic: act8865 at 5b {
+ compatible = "active-semi,act8865";
+ reg = <0x5b>;
+ status = "disabled";
+
+ regulators {
+ vcc_1v8_reg: DCDC_REG1 {
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcc_1v2_reg: DCDC_REG2 {
+ regulator-name = "VCC_1V2";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ };
+
+ vcc_3v3_reg: DCDC_REG3 {
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vddana_reg: LDO_REG1 {
+ regulator-name = "VDDANA";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vddfuse_reg: LDO_REG2 {
+ regulator-name = "FUSE_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+ };
+ };
+ };
+ };
+
+ nand0: nand at 60000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+ status = "okay";
+
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv at c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb at 180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ d2 {
+ label = "d2";
+ gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
new file mode 100644
index 0000000..62c6230
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
@@ -0,0 +1,265 @@
+/*
+ * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include "sama5d3xcm_cmp.dtsi"
+
+/ {
+ compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ mmc0: mmc at f0000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ spi0: spi at f0004000 {
+ dmas = <0>, <0>; /* Do not use DMA for spi0 */
+
+ m25p80 at 0 {
+ compatible = "atmel,at25df321a";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ ssc0: ssc at f0008000 {
+ atmel,clk-from-rk-pin;
+ };
+
+ /*
+ * i2c0 conflicts with ISI:
+ * disable it to allow the use of ISI
+ * can not enable audio when i2c0 disabled
+ */
+ i2c0: i2c at f0014000 {
+ wm8904: wm8904 at 1a {
+ compatible = "wlf,wm8904";
+ reg = <0x1a>;
+ clocks = <&pck0>;
+ clock-names = "mclk";
+ };
+ };
+
+ i2c1: i2c at f0018000 {
+ ov2640: camera at 0x30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+ resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+ /* use pck1 for the master clock of ov2640 */
+ clocks = <&pck1>;
+ clock-names = "xvclk";
+ assigned-clocks = <&pck1>;
+ assigned-clock-rates = <25000000>;
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+ };
+
+ usart1: serial at f0020000 {
+ dmas = <0>, <0>; /* Do not use DMA for usart1 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+ status = "okay";
+ };
+
+ isi: isi at f0034000 {
+ port {
+ isi_0: endpoint {
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ vsync-active = <1>;
+ hsync-active = <1>;
+ };
+ };
+ };
+
+ mmc1: mmc at f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ adc0: adc at f8018000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <
+ &pinctrl_adc0_adtrg
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ >;
+ pinctrl-1 = <
+ &pinctrl_adc0_adtrg_sleep
+ &pinctrl_adc0_ad0_sleep
+ &pinctrl_adc0_ad1_sleep
+ &pinctrl_adc0_ad2_sleep
+ &pinctrl_adc0_ad3_sleep
+ &pinctrl_adc0_ad4_sleep
+ >;
+ status = "okay";
+ };
+
+ macb1: ethernet at f802c000 {
+ phy-mode = "rmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy at 1 {
+ /*interrupt-parent = <&pioE>;*/
+ /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
+ reg = <1>;
+ };
+ };
+
+ pinctrl at fffff200 {
+ adc0 {
+ pinctrl_adc0_adtrg_sleep: adc0_adtrg_1 {
+ atmel,pins =
+ <AT91_PIOD 19 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD19 GPIO output 0 */
+ };
+ pinctrl_adc0_ad0_sleep: adc0_ad0_1 {
+ atmel,pins =
+ <AT91_PIOD 20 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD20 GPIO output 0 */
+ };
+ pinctrl_adc0_ad1_sleep: adc0_ad1_1 {
+ atmel,pins =
+ <AT91_PIOD 21 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD21 GPIO output 0 */
+ };
+ pinctrl_adc0_ad2_sleep: adc0_ad2_1 {
+ atmel,pins =
+ <AT91_PIOD 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD22 GPIO output 0 */
+ };
+ pinctrl_adc0_ad3_sleep: adc0_ad3_1 {
+ atmel,pins =
+ <AT91_PIOD 23 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD23 GPIO output 0 */
+ };
+ pinctrl_adc0_ad4_sleep: adc0_ad4_1 {
+ atmel,pins =
+ <AT91_PIOD 24 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD24 GPIO output 0 */
+ };
+ };
+
+ board {
+ pinctrl_gpio_keys: gpio_keys {
+ atmel,pins =
+ <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_mmc0_cd: mmc0_cd {
+ atmel,pins =
+ <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
+ };
+
+ pinctrl_mmc1_cd: mmc1_cd {
+ atmel,pins =
+ <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
+ };
+
+ pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+ atmel,pins =
+ <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */
+ };
+
+ pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+ atmel,pins =
+ <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */
+ };
+
+ pinctrl_sensor_reset: sensor_reset-0 {
+ atmel,pins =
+ <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */
+ };
+
+ pinctrl_sensor_power: sensor_power-0 {
+ atmel,pins =
+ <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
+ };
+ };
+ };
+
+ dbgu: serial at ffffee00 {
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+ status = "okay";
+ };
+
+ watchdog at fffffe40 {
+ status = "okay";
+ };
+ };
+
+ usb0: gadget at 00500000 {
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+ };
+
+ sound {
+ compatible = "atmel,asoc-wm8904";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+ atmel,model = "wm8904 @ SAMA5D3EK";
+ atmel,audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "IN2L", "Line In Jack",
+ "IN2R", "Line In Jack",
+ "Mic", "MICBIAS",
+ "IN1L", "Mic";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8904>;
+
+ status = "disabled";
+ };
+
+ /* Conflict with LCD pins */
+ gpio_keys {
+ compatible = "gpio-keys";
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ pb_user1 {
+ label = "pb_user1";
+ gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
+ linux,code = <0x100>;
+ gpio-key,wakeup;
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-02 5:28 ` kbuild test robot
0 siblings, 0 replies; 15+ messages in thread
From: kbuild test robot @ 2016-11-02 5:28 UTC (permalink / raw)
To: Wenyou Yang
Cc: kbuild-all, Nicolas Ferre, Alexandre Belloni, Russell King,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
linux-kernel, Wenyou Yang, devicetree, linux-arm-kernel,
Wenyou Yang
[-- Attachment #1: Type: text/plain, Size: 1098 bytes --]
Hi Wenyou,
[auto build test ERROR on at91/at91-next]
[also build test ERROR on v4.9-rc3 next-20161028]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Wenyou-Yang/ARM-at91-dt-add-dts-file-for-sama5d36ek-CMP-board/20161102-111152
base: https://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91.git at91-next
config: arm-at91_dt_defconfig (attached as .config)
compiler: arm-linux-gnueabi-gcc (Debian 6.1.1-9) 6.1.1 20160705
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=arm
All errors (new ones prefixed by >>):
>> Error: arch/arm/boot/dts/sama5d3xmb_cmp.dtsi:143.17-18 syntax error
FATAL ERROR: Unable to parse input tree
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 21326 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-02 5:28 ` kbuild test robot
0 siblings, 0 replies; 15+ messages in thread
From: kbuild test robot @ 2016-11-02 5:28 UTC (permalink / raw)
Cc: kbuild-all-JC7UmRfGjtg, Nicolas Ferre, Alexandre Belloni,
Russell King, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
Wenyou Yang, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Wenyou Yang
[-- Attachment #1: Type: text/plain, Size: 1098 bytes --]
Hi Wenyou,
[auto build test ERROR on at91/at91-next]
[also build test ERROR on v4.9-rc3 next-20161028]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Wenyou-Yang/ARM-at91-dt-add-dts-file-for-sama5d36ek-CMP-board/20161102-111152
base: https://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91.git at91-next
config: arm-at91_dt_defconfig (attached as .config)
compiler: arm-linux-gnueabi-gcc (Debian 6.1.1-9) 6.1.1 20160705
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=arm
All errors (new ones prefixed by >>):
>> Error: arch/arm/boot/dts/sama5d3xmb_cmp.dtsi:143.17-18 syntax error
FATAL ERROR: Unable to parse input tree
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 21326 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-02 5:28 ` kbuild test robot
0 siblings, 0 replies; 15+ messages in thread
From: kbuild test robot @ 2016-11-02 5:28 UTC (permalink / raw)
To: linux-arm-kernel
Hi Wenyou,
[auto build test ERROR on at91/at91-next]
[also build test ERROR on v4.9-rc3 next-20161028]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Wenyou-Yang/ARM-at91-dt-add-dts-file-for-sama5d36ek-CMP-board/20161102-111152
base: https://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91.git at91-next
config: arm-at91_dt_defconfig (attached as .config)
compiler: arm-linux-gnueabi-gcc (Debian 6.1.1-9) 6.1.1 20160705
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=arm
All errors (new ones prefixed by >>):
>> Error: arch/arm/boot/dts/sama5d3xmb_cmp.dtsi:143.17-18 syntax error
FATAL ERROR: Unable to parse input tree
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
-------------- next part --------------
A non-text attachment was scrubbed...
Name: .config.gz
Type: application/gzip
Size: 21326 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161102/e70be8e1/attachment-0001.gz>
^ permalink raw reply [flat|nested] 15+ messages in thread
* RE: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-02 5:46 ` Wenyou.Yang-UWL1GkI3JZL3oGB3hsPCZA
0 siblings, 0 replies; 15+ messages in thread
From: Wenyou.Yang @ 2016-11-02 5:46 UTC (permalink / raw)
To: lkp
Cc: kbuild-all, nicolas.ferre, alexandre.belloni, linux, robh+dt,
pawel.moll, mark.rutland, ijc+devicetree, galak, linux-kernel,
devicetree, linux-arm-kernel
> -----Original Message-----
> From: kbuild test robot [mailto:lkp@intel.com]
> Sent: 2016年11月2日 13:28
> To: Wenyou Yang - A41535 <Wenyou.Yang@microchip.com>
> Cc: kbuild-all@01.org; Nicolas Ferre <nicolas.ferre@atmel.com>; Alexandre
> Belloni <alexandre.belloni@free-electrons.com>; Russell King
> <linux@arm.linux.org.uk>; Rob Herring <robh+dt@kernel.org>; Pawel Moll
> <pawel.moll@arm.com>; Mark Rutland <mark.rutland@arm.com>; Ian Campbell
> <ijc+devicetree@hellion.org.uk>; Kumar Gala <galak@codeaurora.org>; linux-
> kernel@vger.kernel.org; Wenyou Yang - A41535
> <Wenyou.Yang@microchip.com>; devicetree@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org; Wenyou Yang - A41535
> <Wenyou.Yang@microchip.com>
> Subject: Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
>
> Hi Wenyou,
>
> [auto build test ERROR on at91/at91-next] [also build test ERROR on v4.9-rc3
> next-20161028] [if your patch is applied to the wrong git tree, please drop us a
> note to help improve the system]
>
> url: https://github.com/0day-ci/linux/commits/Wenyou-Yang/ARM-at91-dt-add-
> dts-file-for-sama5d36ek-CMP-board/20161102-111152
> base: https://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91.git at91-
> next
> config: arm-at91_dt_defconfig (attached as .config)
> compiler: arm-linux-gnueabi-gcc (Debian 6.1.1-9) 6.1.1 20160705
> reproduce:
> wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-
> tests.git/plain/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # save the attached .config to linux build tree
> make.cross ARCH=arm
>
> All errors (new ones prefixed by >>):
>
> >> Error: arch/arm/boot/dts/sama5d3xmb_cmp.dtsi:143.17-18 syntax error
> FATAL ERROR: Unable to parse input tree
Oh, this patch is based on the patch I sent before.
[PATCH] pinctrl: at91: add support for OUTPUT config
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-October/464354.html
I forgot adding this information.
Sorry.
Best Regards,
Wenyou Yang
^ permalink raw reply [flat|nested] 15+ messages in thread
* RE: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-02 5:46 ` Wenyou.Yang-UWL1GkI3JZL3oGB3hsPCZA
0 siblings, 0 replies; 15+ messages in thread
From: Wenyou.Yang-UWL1GkI3JZL3oGB3hsPCZA @ 2016-11-02 5:46 UTC (permalink / raw)
To: lkp-ral2JQCrhuEAvxtiuMwx3w
Cc: kbuild-all-JC7UmRfGjtg, nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w,
alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8,
linux-lFZ/pmaqli7XmaaqVzeoHQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8,
ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset="gb2312", Size: 2237 bytes --]
> -----Original Message-----
> From: kbuild test robot [mailto:lkp@intel.com]
> Sent: 2016Äê11ÔÂ2ÈÕ 13:28
> To: Wenyou Yang - A41535 <Wenyou.Yang@microchip.com>
> Cc: kbuild-all@01.org; Nicolas Ferre <nicolas.ferre@atmel.com>; Alexandre
> Belloni <alexandre.belloni@free-electrons.com>; Russell King
> <linux@arm.linux.org.uk>; Rob Herring <robh+dt@kernel.org>; Pawel Moll
> <pawel.moll@arm.com>; Mark Rutland <mark.rutland@arm.com>; Ian Campbell
> <ijc+devicetree@hellion.org.uk>; Kumar Gala <galak@codeaurora.org>; linux-
> kernel@vger.kernel.org; Wenyou Yang - A41535
> <Wenyou.Yang@microchip.com>; devicetree@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org; Wenyou Yang - A41535
> <Wenyou.Yang@microchip.com>
> Subject: Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
>
> Hi Wenyou,
>
> [auto build test ERROR on at91/at91-next] [also build test ERROR on v4.9-rc3
> next-20161028] [if your patch is applied to the wrong git tree, please drop us a
> note to help improve the system]
>
> url: https://github.com/0day-ci/linux/commits/Wenyou-Yang/ARM-at91-dt-add-
> dts-file-for-sama5d36ek-CMP-board/20161102-111152
> base: https://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91.git at91-
> next
> config: arm-at91_dt_defconfig (attached as .config)
> compiler: arm-linux-gnueabi-gcc (Debian 6.1.1-9) 6.1.1 20160705
> reproduce:
> wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-
> tests.git/plain/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # save the attached .config to linux build tree
> make.cross ARCH=arm
>
> All errors (new ones prefixed by >>):
>
> >> Error: arch/arm/boot/dts/sama5d3xmb_cmp.dtsi:143.17-18 syntax error
> FATAL ERROR: Unable to parse input tree
Oh, this patch is based on the patch I sent before.
[PATCH] pinctrl: at91: add support for OUTPUT config
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-October/464354.html
I forgot adding this information.
Sorry.
Best Regards,
Wenyou Yang
N‹§²æìr¸›yúèšØb²X¬¶Ç§vØ^–)Þº{.nÇ+‰·zøœzÚÞz)í…æèw*\x1fjg¬±¨\x1e¶‰šŽŠÝ¢j.ïÛ°\½½MŽúgjÌæa×\x02››–' ™©Þ¢¸\f¢·¦j:+v‰¨ŠwèjØm¶Ÿÿ¾\a«‘êçzZ+ƒùšŽŠÝ¢j"ú!¶i
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-02 5:46 ` Wenyou.Yang-UWL1GkI3JZL3oGB3hsPCZA
0 siblings, 0 replies; 15+ messages in thread
From: Wenyou.Yang at microchip.com @ 2016-11-02 5:46 UTC (permalink / raw)
To: linux-arm-kernel
> -----Original Message-----
> From: kbuild test robot [mailto:lkp at intel.com]
> Sent: 2016?11?2? 13:28
> To: Wenyou Yang - A41535 <Wenyou.Yang@microchip.com>
> Cc: kbuild-all at 01.org; Nicolas Ferre <nicolas.ferre@atmel.com>; Alexandre
> Belloni <alexandre.belloni@free-electrons.com>; Russell King
> <linux@arm.linux.org.uk>; Rob Herring <robh+dt@kernel.org>; Pawel Moll
> <pawel.moll@arm.com>; Mark Rutland <mark.rutland@arm.com>; Ian Campbell
> <ijc+devicetree@hellion.org.uk>; Kumar Gala <galak@codeaurora.org>; linux-
> kernel at vger.kernel.org; Wenyou Yang - A41535
> <Wenyou.Yang@microchip.com>; devicetree at vger.kernel.org; linux-arm-
> kernel at lists.infradead.org; Wenyou Yang - A41535
> <Wenyou.Yang@microchip.com>
> Subject: Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
>
> Hi Wenyou,
>
> [auto build test ERROR on at91/at91-next] [also build test ERROR on v4.9-rc3
> next-20161028] [if your patch is applied to the wrong git tree, please drop us a
> note to help improve the system]
>
> url: https://github.com/0day-ci/linux/commits/Wenyou-Yang/ARM-at91-dt-add-
> dts-file-for-sama5d36ek-CMP-board/20161102-111152
> base: https://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91.git at91-
> next
> config: arm-at91_dt_defconfig (attached as .config)
> compiler: arm-linux-gnueabi-gcc (Debian 6.1.1-9) 6.1.1 20160705
> reproduce:
> wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-
> tests.git/plain/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # save the attached .config to linux build tree
> make.cross ARCH=arm
>
> All errors (new ones prefixed by >>):
>
> >> Error: arch/arm/boot/dts/sama5d3xmb_cmp.dtsi:143.17-18 syntax error
> FATAL ERROR: Unable to parse input tree
Oh, this patch is based on the patch I sent before.
[PATCH] pinctrl: at91: add support for OUTPUT config
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-October/464354.html
I forgot adding this information.
Sorry.
Best Regards,
Wenyou Yang
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
2016-11-02 3:05 ` Wenyou Yang
(?)
@ 2016-11-14 15:36 ` Nicolas Ferre
-1 siblings, 0 replies; 15+ messages in thread
From: Nicolas Ferre @ 2016-11-14 15:36 UTC (permalink / raw)
To: Wenyou Yang, Alexandre Belloni, Russell King, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Cc: linux-kernel, Wenyou Yang, devicetree, linux-arm-kernel
Le 02/11/2016 à 04:05, Wenyou Yang a écrit :
> The sama5d36ek CMP board is the variant of sama5d3xek board.
> It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
> some power rail. Its main purpose is used to measure the power
> consumption.
> The difference of the sama5d36ek CMP dts from sama5d36ek dts
> is listed as below.
> 1. The USB host nodes are removed, that is, the USB host is disabled.
> 2. The gpio_keys node is added to wake up from the sleep.
> 3. The LCD isn't supported due to the pins for LCD are conflicted
> with gpio_keys.
> 4. The adc0 node support the pinctrl sleep state to fix the over
> consumption on VDDANA.
>
> As said in errata, "When the USB host ports are used in high speed
> mode (EHCI), it is not possible to suspend the ports if no device is
> attached on each port. This leads to increased power consumption even
> if the system is in a low power mode." That is why the the USB host
> is disabled.
>
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
> ---
>
> Changes in v2:
> - Add the pinctrl sleep state for adc0 node to fix the over
> consumption on VDDANA.
> - Improve the commit log.
>
> arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
> arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
> arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
> 3 files changed, 482 insertions(+)
> create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
> create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
>
> diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> new file mode 100644
> index 0000000..fd6bcd6
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> @@ -0,0 +1,51 @@
> +/*
> + * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.
No, in fact we now use a dual license scheme for DT files. Please have a
look at the recent board that we posted to take the header from them.
> + */
> +/dts-v1/;
> +#include "sama5d36.dtsi"
> +#include "sama5d3xmb_cmp.dtsi"
> +
> +/ {
> + model = "Atmel SAMA5D36-EK";
> + compatible = "atmel,sama5d36ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
I don't think the model name nor the compatible string reflect the
nature of this new "CMP" board.
> +
> + ahb {
> + apb {
> + spi0: spi@f0004000 {
> + status = "okay";
> + };
> +
> + ssc0: ssc@f0008000 {
> + status = "okay";
> + };
> +
> + can0: can@f000c000 {
> + status = "okay";
> + };
> +
> + i2c0: i2c@f0014000 {
> + status = "okay";
> + };
> +
> + i2c1: i2c@f0018000 {
> + status = "okay";
> + };
> +
> + macb0: ethernet@f0028000 {
> + status = "okay";
> + };
> +
> + macb1: ethernet@f802c000 {
> + status = "okay";
> + };
> + };
> + };
> +
> + sound {
> + status = "okay";
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> new file mode 100644
> index 0000000..77638c3
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> @@ -0,0 +1,166 @@
> +/*
> + * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.
Ditto.
> + */
> +
> +/ {
> + compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
Ditto.
> +
> + chosen {
> + bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
Remove bootargs.
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + reg = <0x20000000 0x20000000>;
> + };
> +
> + clocks {
> + slow_xtal {
> + clock-frequency = <32768>;
> + };
> +
> + main_xtal {
> + clock-frequency = <12000000>;
> + };
> + };
> +
> + ahb {
> + apb {
> + spi0: spi@f0004000 {
> + cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
> + };
> +
> + macb0: ethernet@f0028000 {
> + phy-mode = "rgmii";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethernet-phy@1 {
> + reg = <0x1>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> +
> + ethernet-phy@7 {
> + reg = <0x7>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> + };
> +
> + i2c1: i2c@f0018000 {
> + pmic: act8865@5b {
> + compatible = "active-semi,act8865";
> + reg = <0x5b>;
> + status = "disabled";
> +
> + regulators {
> + vcc_1v8_reg: DCDC_REG1 {
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v2_reg: DCDC_REG2 {
> + regulator-name = "VCC_1V2";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3_reg: DCDC_REG3 {
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddana_reg: LDO_REG1 {
> + regulator-name = "VDDANA";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddfuse_reg: LDO_REG2 {
> + regulator-name = "FUSE_2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + };
> + };
> + };
> + };
> + };
> +
> + nand0: nand@60000000 {
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + atmel,has-pmecc;
> + atmel,pmecc-cap = <4>;
> + atmel,pmecc-sector-size = <512>;
> + nand-on-flash-bbt;
> + status = "okay";
> +
> + at91bootstrap@0 {
> + label = "at91bootstrap";
> + reg = <0x0 0x40000>;
> + };
> +
> + bootloader@40000 {
> + label = "bootloader";
> + reg = <0x40000 0x80000>;
> + };
> +
> + bootloaderenv@c0000 {
> + label = "bootloader env";
> + reg = <0xc0000 0xc0000>;
> + };
> +
> + dtb@180000 {
> + label = "device tree";
> + reg = <0x180000 0x80000>;
> + };
> +
> + kernel@200000 {
> + label = "kernel";
> + reg = <0x200000 0x600000>;
> + };
> +
> + rootfs@800000 {
> + label = "rootfs";
> + reg = <0x800000 0x0f800000>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + d2 {
> + label = "d2";
> + gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> new file mode 100644
> index 0000000..62c6230
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> @@ -0,0 +1,265 @@
> +/*
> + * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.
Ditto.
> + */
> +#include "sama5d3xcm_cmp.dtsi"
> +
> +/ {
> + compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
Ditto.
> +
> + ahb {
> + apb {
> + mmc0: mmc@f0000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
> + status = "okay";
> + slot@0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + spi0: spi@f0004000 {
> + dmas = <0>, <0>; /* Do not use DMA for spi0 */
> +
> + m25p80@0 {
> + compatible = "atmel,at25df321a";
> + spi-max-frequency = <50000000>;
> + reg = <0>;
> + };
> + };
> +
> + ssc0: ssc@f0008000 {
> + atmel,clk-from-rk-pin;
> + };
> +
> + /*
> + * i2c0 conflicts with ISI:
> + * disable it to allow the use of ISI
> + * can not enable audio when i2c0 disabled
> + */
> + i2c0: i2c@f0014000 {
> + wm8904: wm8904@1a {
> + compatible = "wlf,wm8904";
> + reg = <0x1a>;
> + clocks = <&pck0>;
> + clock-names = "mclk";
> + };
> + };
> +
> + i2c1: i2c@f0018000 {
> + ov2640: camera@0x30 {
> + compatible = "ovti,ov2640";
> + reg = <0x30>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
> + resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
> + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
> + /* use pck1 for the master clock of ov2640 */
> + clocks = <&pck1>;
> + clock-names = "xvclk";
> + assigned-clocks = <&pck1>;
> + assigned-clock-rates = <25000000>;
> +
> + port {
> + ov2640_0: endpoint {
> + remote-endpoint = <&isi_0>;
> + bus-width = <8>;
> + };
> + };
> + };
> + };
> +
> + usart1: serial@f0020000 {
> + dmas = <0>, <0>; /* Do not use DMA for usart1 */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
> + status = "okay";
> + };
> +
> + isi: isi@f0034000 {
> + port {
> + isi_0: endpoint {
> + remote-endpoint = <&ov2640_0>;
> + bus-width = <8>;
> + vsync-active = <1>;
> + hsync-active = <1>;
> + };
> + };
> + };
> +
> + mmc1: mmc@f8000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
> + status = "okay";
> + slot@0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + adc0: adc@f8018000 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <
> + &pinctrl_adc0_adtrg
> + &pinctrl_adc0_ad0
> + &pinctrl_adc0_ad1
> + &pinctrl_adc0_ad2
> + &pinctrl_adc0_ad3
> + &pinctrl_adc0_ad4
> + >;
> + pinctrl-1 = <
> + &pinctrl_adc0_adtrg_sleep
> + &pinctrl_adc0_ad0_sleep
> + &pinctrl_adc0_ad1_sleep
> + &pinctrl_adc0_ad2_sleep
> + &pinctrl_adc0_ad3_sleep
> + &pinctrl_adc0_ad4_sleep
> + >;
> + status = "okay";
> + };
> +
> + macb1: ethernet@f802c000 {
> + phy-mode = "rmii";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy@1 {
> + /*interrupt-parent = <&pioE>;*/
> + /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
> + reg = <1>;
> + };
> + };
> +
> + pinctrl@fffff200 {
> + adc0 {
> + pinctrl_adc0_adtrg_sleep: adc0_adtrg_1 {
> + atmel,pins =
> + <AT91_PIOD 19 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD19 GPIO output 0 */
> + };
> + pinctrl_adc0_ad0_sleep: adc0_ad0_1 {
> + atmel,pins =
> + <AT91_PIOD 20 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD20 GPIO output 0 */
> + };
> + pinctrl_adc0_ad1_sleep: adc0_ad1_1 {
> + atmel,pins =
> + <AT91_PIOD 21 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD21 GPIO output 0 */
> + };
> + pinctrl_adc0_ad2_sleep: adc0_ad2_1 {
> + atmel,pins =
> + <AT91_PIOD 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD22 GPIO output 0 */
> + };
> + pinctrl_adc0_ad3_sleep: adc0_ad3_1 {
> + atmel,pins =
> + <AT91_PIOD 23 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD23 GPIO output 0 */
> + };
> + pinctrl_adc0_ad4_sleep: adc0_ad4_1 {
> + atmel,pins =
> + <AT91_PIOD 24 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD24 GPIO output 0 */
Please remove all these comments. The binding is good enough to
understand easily.
> + };
> + };
> +
> + board {
> + pinctrl_gpio_keys: gpio_keys {
> + atmel,pins =
> + <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_mmc0_cd: mmc0_cd {
> + atmel,pins =
> + <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
> + };
> +
> + pinctrl_mmc1_cd: mmc1_cd {
> + atmel,pins =
> + <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
> + };
> +
> + pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
> + atmel,pins =
> + <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */
> + };
> +
> + pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
> + atmel,pins =
> + <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */
> + };
> +
> + pinctrl_sensor_reset: sensor_reset-0 {
> + atmel,pins =
> + <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */
> + };
> +
> + pinctrl_sensor_power: sensor_power-0 {
> + atmel,pins =
> + <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
> + };
> +
> + pinctrl_usba_vbus: usba_vbus {
> + atmel,pins =
> + <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
Here again, all comments are not or great use: remove them.
> + };
> + };
> + };
> +
> + dbgu: serial@ffffee00 {
> + dmas = <0>, <0>; /* Do not use DMA for dbgu */
> + status = "okay";
> + };
> +
> + watchdog@fffffe40 {
> + status = "okay";
> + };
> + };
> +
> + usb0: gadget@00500000 {
> + atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usba_vbus>;
> + status = "okay";
> + };
> + };
> +
> + sound {
> + compatible = "atmel,asoc-wm8904";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
> +
> + atmel,model = "wm8904 @ SAMA5D3EK";
> + atmel,audio-routing =
> + "Headphone Jack", "HPOUTL",
> + "Headphone Jack", "HPOUTR",
> + "IN2L", "Line In Jack",
> + "IN2R", "Line In Jack",
> + "Mic", "MICBIAS",
> + "IN1L", "Mic";
> +
> + atmel,ssc-controller = <&ssc0>;
> + atmel,audio-codec = <&wm8904>;
> +
> + status = "disabled";
> + };
> +
> + /* Conflict with LCD pins */
> + gpio_keys {
> + compatible = "gpio-keys";
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + pb_user1 {
> + label = "pb_user1";
> + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
> + linux,code = <0x100>;
> + gpio-key,wakeup;
> + };
> + };
> +};
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-14 15:36 ` Nicolas Ferre
0 siblings, 0 replies; 15+ messages in thread
From: Nicolas Ferre @ 2016-11-14 15:36 UTC (permalink / raw)
To: Wenyou Yang, Alexandre Belloni, Russell King, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Cc: linux-kernel, Wenyou Yang, devicetree, linux-arm-kernel
Le 02/11/2016 à 04:05, Wenyou Yang a écrit :
> The sama5d36ek CMP board is the variant of sama5d3xek board.
> It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
> some power rail. Its main purpose is used to measure the power
> consumption.
> The difference of the sama5d36ek CMP dts from sama5d36ek dts
> is listed as below.
> 1. The USB host nodes are removed, that is, the USB host is disabled.
> 2. The gpio_keys node is added to wake up from the sleep.
> 3. The LCD isn't supported due to the pins for LCD are conflicted
> with gpio_keys.
> 4. The adc0 node support the pinctrl sleep state to fix the over
> consumption on VDDANA.
>
> As said in errata, "When the USB host ports are used in high speed
> mode (EHCI), it is not possible to suspend the ports if no device is
> attached on each port. This leads to increased power consumption even
> if the system is in a low power mode." That is why the the USB host
> is disabled.
>
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
> ---
>
> Changes in v2:
> - Add the pinctrl sleep state for adc0 node to fix the over
> consumption on VDDANA.
> - Improve the commit log.
>
> arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
> arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
> arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
> 3 files changed, 482 insertions(+)
> create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
> create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
>
> diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> new file mode 100644
> index 0000000..fd6bcd6
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> @@ -0,0 +1,51 @@
> +/*
> + * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.
No, in fact we now use a dual license scheme for DT files. Please have a
look at the recent board that we posted to take the header from them.
> + */
> +/dts-v1/;
> +#include "sama5d36.dtsi"
> +#include "sama5d3xmb_cmp.dtsi"
> +
> +/ {
> + model = "Atmel SAMA5D36-EK";
> + compatible = "atmel,sama5d36ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
I don't think the model name nor the compatible string reflect the
nature of this new "CMP" board.
> +
> + ahb {
> + apb {
> + spi0: spi@f0004000 {
> + status = "okay";
> + };
> +
> + ssc0: ssc@f0008000 {
> + status = "okay";
> + };
> +
> + can0: can@f000c000 {
> + status = "okay";
> + };
> +
> + i2c0: i2c@f0014000 {
> + status = "okay";
> + };
> +
> + i2c1: i2c@f0018000 {
> + status = "okay";
> + };
> +
> + macb0: ethernet@f0028000 {
> + status = "okay";
> + };
> +
> + macb1: ethernet@f802c000 {
> + status = "okay";
> + };
> + };
> + };
> +
> + sound {
> + status = "okay";
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> new file mode 100644
> index 0000000..77638c3
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> @@ -0,0 +1,166 @@
> +/*
> + * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.
Ditto.
> + */
> +
> +/ {
> + compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
Ditto.
> +
> + chosen {
> + bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
Remove bootargs.
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + reg = <0x20000000 0x20000000>;
> + };
> +
> + clocks {
> + slow_xtal {
> + clock-frequency = <32768>;
> + };
> +
> + main_xtal {
> + clock-frequency = <12000000>;
> + };
> + };
> +
> + ahb {
> + apb {
> + spi0: spi@f0004000 {
> + cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
> + };
> +
> + macb0: ethernet@f0028000 {
> + phy-mode = "rgmii";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethernet-phy@1 {
> + reg = <0x1>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> +
> + ethernet-phy@7 {
> + reg = <0x7>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> + };
> +
> + i2c1: i2c@f0018000 {
> + pmic: act8865@5b {
> + compatible = "active-semi,act8865";
> + reg = <0x5b>;
> + status = "disabled";
> +
> + regulators {
> + vcc_1v8_reg: DCDC_REG1 {
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v2_reg: DCDC_REG2 {
> + regulator-name = "VCC_1V2";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3_reg: DCDC_REG3 {
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddana_reg: LDO_REG1 {
> + regulator-name = "VDDANA";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddfuse_reg: LDO_REG2 {
> + regulator-name = "FUSE_2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + };
> + };
> + };
> + };
> + };
> +
> + nand0: nand@60000000 {
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + atmel,has-pmecc;
> + atmel,pmecc-cap = <4>;
> + atmel,pmecc-sector-size = <512>;
> + nand-on-flash-bbt;
> + status = "okay";
> +
> + at91bootstrap@0 {
> + label = "at91bootstrap";
> + reg = <0x0 0x40000>;
> + };
> +
> + bootloader@40000 {
> + label = "bootloader";
> + reg = <0x40000 0x80000>;
> + };
> +
> + bootloaderenv@c0000 {
> + label = "bootloader env";
> + reg = <0xc0000 0xc0000>;
> + };
> +
> + dtb@180000 {
> + label = "device tree";
> + reg = <0x180000 0x80000>;
> + };
> +
> + kernel@200000 {
> + label = "kernel";
> + reg = <0x200000 0x600000>;
> + };
> +
> + rootfs@800000 {
> + label = "rootfs";
> + reg = <0x800000 0x0f800000>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + d2 {
> + label = "d2";
> + gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> new file mode 100644
> index 0000000..62c6230
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> @@ -0,0 +1,265 @@
> +/*
> + * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.
Ditto.
> + */
> +#include "sama5d3xcm_cmp.dtsi"
> +
> +/ {
> + compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
Ditto.
> +
> + ahb {
> + apb {
> + mmc0: mmc@f0000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
> + status = "okay";
> + slot@0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + spi0: spi@f0004000 {
> + dmas = <0>, <0>; /* Do not use DMA for spi0 */
> +
> + m25p80@0 {
> + compatible = "atmel,at25df321a";
> + spi-max-frequency = <50000000>;
> + reg = <0>;
> + };
> + };
> +
> + ssc0: ssc@f0008000 {
> + atmel,clk-from-rk-pin;
> + };
> +
> + /*
> + * i2c0 conflicts with ISI:
> + * disable it to allow the use of ISI
> + * can not enable audio when i2c0 disabled
> + */
> + i2c0: i2c@f0014000 {
> + wm8904: wm8904@1a {
> + compatible = "wlf,wm8904";
> + reg = <0x1a>;
> + clocks = <&pck0>;
> + clock-names = "mclk";
> + };
> + };
> +
> + i2c1: i2c@f0018000 {
> + ov2640: camera@0x30 {
> + compatible = "ovti,ov2640";
> + reg = <0x30>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
> + resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
> + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
> + /* use pck1 for the master clock of ov2640 */
> + clocks = <&pck1>;
> + clock-names = "xvclk";
> + assigned-clocks = <&pck1>;
> + assigned-clock-rates = <25000000>;
> +
> + port {
> + ov2640_0: endpoint {
> + remote-endpoint = <&isi_0>;
> + bus-width = <8>;
> + };
> + };
> + };
> + };
> +
> + usart1: serial@f0020000 {
> + dmas = <0>, <0>; /* Do not use DMA for usart1 */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
> + status = "okay";
> + };
> +
> + isi: isi@f0034000 {
> + port {
> + isi_0: endpoint {
> + remote-endpoint = <&ov2640_0>;
> + bus-width = <8>;
> + vsync-active = <1>;
> + hsync-active = <1>;
> + };
> + };
> + };
> +
> + mmc1: mmc@f8000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
> + status = "okay";
> + slot@0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + adc0: adc@f8018000 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <
> + &pinctrl_adc0_adtrg
> + &pinctrl_adc0_ad0
> + &pinctrl_adc0_ad1
> + &pinctrl_adc0_ad2
> + &pinctrl_adc0_ad3
> + &pinctrl_adc0_ad4
> + >;
> + pinctrl-1 = <
> + &pinctrl_adc0_adtrg_sleep
> + &pinctrl_adc0_ad0_sleep
> + &pinctrl_adc0_ad1_sleep
> + &pinctrl_adc0_ad2_sleep
> + &pinctrl_adc0_ad3_sleep
> + &pinctrl_adc0_ad4_sleep
> + >;
> + status = "okay";
> + };
> +
> + macb1: ethernet@f802c000 {
> + phy-mode = "rmii";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy@1 {
> + /*interrupt-parent = <&pioE>;*/
> + /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
> + reg = <1>;
> + };
> + };
> +
> + pinctrl@fffff200 {
> + adc0 {
> + pinctrl_adc0_adtrg_sleep: adc0_adtrg_1 {
> + atmel,pins =
> + <AT91_PIOD 19 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD19 GPIO output 0 */
> + };
> + pinctrl_adc0_ad0_sleep: adc0_ad0_1 {
> + atmel,pins =
> + <AT91_PIOD 20 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD20 GPIO output 0 */
> + };
> + pinctrl_adc0_ad1_sleep: adc0_ad1_1 {
> + atmel,pins =
> + <AT91_PIOD 21 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD21 GPIO output 0 */
> + };
> + pinctrl_adc0_ad2_sleep: adc0_ad2_1 {
> + atmel,pins =
> + <AT91_PIOD 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD22 GPIO output 0 */
> + };
> + pinctrl_adc0_ad3_sleep: adc0_ad3_1 {
> + atmel,pins =
> + <AT91_PIOD 23 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD23 GPIO output 0 */
> + };
> + pinctrl_adc0_ad4_sleep: adc0_ad4_1 {
> + atmel,pins =
> + <AT91_PIOD 24 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD24 GPIO output 0 */
Please remove all these comments. The binding is good enough to
understand easily.
> + };
> + };
> +
> + board {
> + pinctrl_gpio_keys: gpio_keys {
> + atmel,pins =
> + <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_mmc0_cd: mmc0_cd {
> + atmel,pins =
> + <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
> + };
> +
> + pinctrl_mmc1_cd: mmc1_cd {
> + atmel,pins =
> + <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
> + };
> +
> + pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
> + atmel,pins =
> + <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */
> + };
> +
> + pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
> + atmel,pins =
> + <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */
> + };
> +
> + pinctrl_sensor_reset: sensor_reset-0 {
> + atmel,pins =
> + <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */
> + };
> +
> + pinctrl_sensor_power: sensor_power-0 {
> + atmel,pins =
> + <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
> + };
> +
> + pinctrl_usba_vbus: usba_vbus {
> + atmel,pins =
> + <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
Here again, all comments are not or great use: remove them.
> + };
> + };
> + };
> +
> + dbgu: serial@ffffee00 {
> + dmas = <0>, <0>; /* Do not use DMA for dbgu */
> + status = "okay";
> + };
> +
> + watchdog@fffffe40 {
> + status = "okay";
> + };
> + };
> +
> + usb0: gadget@00500000 {
> + atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usba_vbus>;
> + status = "okay";
> + };
> + };
> +
> + sound {
> + compatible = "atmel,asoc-wm8904";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
> +
> + atmel,model = "wm8904 @ SAMA5D3EK";
> + atmel,audio-routing =
> + "Headphone Jack", "HPOUTL",
> + "Headphone Jack", "HPOUTR",
> + "IN2L", "Line In Jack",
> + "IN2R", "Line In Jack",
> + "Mic", "MICBIAS",
> + "IN1L", "Mic";
> +
> + atmel,ssc-controller = <&ssc0>;
> + atmel,audio-codec = <&wm8904>;
> +
> + status = "disabled";
> + };
> +
> + /* Conflict with LCD pins */
> + gpio_keys {
> + compatible = "gpio-keys";
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + pb_user1 {
> + label = "pb_user1";
> + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
> + linux,code = <0x100>;
> + gpio-key,wakeup;
> + };
> + };
> +};
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-14 15:36 ` Nicolas Ferre
0 siblings, 0 replies; 15+ messages in thread
From: Nicolas Ferre @ 2016-11-14 15:36 UTC (permalink / raw)
To: linux-arm-kernel
Le 02/11/2016 ? 04:05, Wenyou Yang a ?crit :
> The sama5d36ek CMP board is the variant of sama5d3xek board.
> It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
> some power rail. Its main purpose is used to measure the power
> consumption.
> The difference of the sama5d36ek CMP dts from sama5d36ek dts
> is listed as below.
> 1. The USB host nodes are removed, that is, the USB host is disabled.
> 2. The gpio_keys node is added to wake up from the sleep.
> 3. The LCD isn't supported due to the pins for LCD are conflicted
> with gpio_keys.
> 4. The adc0 node support the pinctrl sleep state to fix the over
> consumption on VDDANA.
>
> As said in errata, "When the USB host ports are used in high speed
> mode (EHCI), it is not possible to suspend the ports if no device is
> attached on each port. This leads to increased power consumption even
> if the system is in a low power mode." That is why the the USB host
> is disabled.
>
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
> ---
>
> Changes in v2:
> - Add the pinctrl sleep state for adc0 node to fix the over
> consumption on VDDANA.
> - Improve the commit log.
>
> arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
> arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
> arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
> 3 files changed, 482 insertions(+)
> create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
> create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
>
> diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> new file mode 100644
> index 0000000..fd6bcd6
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> @@ -0,0 +1,51 @@
> +/*
> + * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.
No, in fact we now use a dual license scheme for DT files. Please have a
look at the recent board that we posted to take the header from them.
> + */
> +/dts-v1/;
> +#include "sama5d36.dtsi"
> +#include "sama5d3xmb_cmp.dtsi"
> +
> +/ {
> + model = "Atmel SAMA5D36-EK";
> + compatible = "atmel,sama5d36ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
I don't think the model name nor the compatible string reflect the
nature of this new "CMP" board.
> +
> + ahb {
> + apb {
> + spi0: spi at f0004000 {
> + status = "okay";
> + };
> +
> + ssc0: ssc at f0008000 {
> + status = "okay";
> + };
> +
> + can0: can at f000c000 {
> + status = "okay";
> + };
> +
> + i2c0: i2c at f0014000 {
> + status = "okay";
> + };
> +
> + i2c1: i2c at f0018000 {
> + status = "okay";
> + };
> +
> + macb0: ethernet at f0028000 {
> + status = "okay";
> + };
> +
> + macb1: ethernet at f802c000 {
> + status = "okay";
> + };
> + };
> + };
> +
> + sound {
> + status = "okay";
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> new file mode 100644
> index 0000000..77638c3
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> @@ -0,0 +1,166 @@
> +/*
> + * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.
Ditto.
> + */
> +
> +/ {
> + compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
Ditto.
> +
> + chosen {
> + bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
Remove bootargs.
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + reg = <0x20000000 0x20000000>;
> + };
> +
> + clocks {
> + slow_xtal {
> + clock-frequency = <32768>;
> + };
> +
> + main_xtal {
> + clock-frequency = <12000000>;
> + };
> + };
> +
> + ahb {
> + apb {
> + spi0: spi at f0004000 {
> + cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
> + };
> +
> + macb0: ethernet at f0028000 {
> + phy-mode = "rgmii";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethernet-phy at 1 {
> + reg = <0x1>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> +
> + ethernet-phy at 7 {
> + reg = <0x7>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> + };
> +
> + i2c1: i2c at f0018000 {
> + pmic: act8865 at 5b {
> + compatible = "active-semi,act8865";
> + reg = <0x5b>;
> + status = "disabled";
> +
> + regulators {
> + vcc_1v8_reg: DCDC_REG1 {
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v2_reg: DCDC_REG2 {
> + regulator-name = "VCC_1V2";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3_reg: DCDC_REG3 {
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddana_reg: LDO_REG1 {
> + regulator-name = "VDDANA";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddfuse_reg: LDO_REG2 {
> + regulator-name = "FUSE_2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + };
> + };
> + };
> + };
> + };
> +
> + nand0: nand at 60000000 {
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + atmel,has-pmecc;
> + atmel,pmecc-cap = <4>;
> + atmel,pmecc-sector-size = <512>;
> + nand-on-flash-bbt;
> + status = "okay";
> +
> + at91bootstrap at 0 {
> + label = "at91bootstrap";
> + reg = <0x0 0x40000>;
> + };
> +
> + bootloader at 40000 {
> + label = "bootloader";
> + reg = <0x40000 0x80000>;
> + };
> +
> + bootloaderenv at c0000 {
> + label = "bootloader env";
> + reg = <0xc0000 0xc0000>;
> + };
> +
> + dtb at 180000 {
> + label = "device tree";
> + reg = <0x180000 0x80000>;
> + };
> +
> + kernel at 200000 {
> + label = "kernel";
> + reg = <0x200000 0x600000>;
> + };
> +
> + rootfs at 800000 {
> + label = "rootfs";
> + reg = <0x800000 0x0f800000>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + d2 {
> + label = "d2";
> + gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> new file mode 100644
> index 0000000..62c6230
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> @@ -0,0 +1,265 @@
> +/*
> + * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.
Ditto.
> + */
> +#include "sama5d3xcm_cmp.dtsi"
> +
> +/ {
> + compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
Ditto.
> +
> + ahb {
> + apb {
> + mmc0: mmc at f0000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
> + status = "okay";
> + slot at 0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + spi0: spi at f0004000 {
> + dmas = <0>, <0>; /* Do not use DMA for spi0 */
> +
> + m25p80 at 0 {
> + compatible = "atmel,at25df321a";
> + spi-max-frequency = <50000000>;
> + reg = <0>;
> + };
> + };
> +
> + ssc0: ssc at f0008000 {
> + atmel,clk-from-rk-pin;
> + };
> +
> + /*
> + * i2c0 conflicts with ISI:
> + * disable it to allow the use of ISI
> + * can not enable audio when i2c0 disabled
> + */
> + i2c0: i2c at f0014000 {
> + wm8904: wm8904 at 1a {
> + compatible = "wlf,wm8904";
> + reg = <0x1a>;
> + clocks = <&pck0>;
> + clock-names = "mclk";
> + };
> + };
> +
> + i2c1: i2c at f0018000 {
> + ov2640: camera at 0x30 {
> + compatible = "ovti,ov2640";
> + reg = <0x30>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
> + resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
> + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
> + /* use pck1 for the master clock of ov2640 */
> + clocks = <&pck1>;
> + clock-names = "xvclk";
> + assigned-clocks = <&pck1>;
> + assigned-clock-rates = <25000000>;
> +
> + port {
> + ov2640_0: endpoint {
> + remote-endpoint = <&isi_0>;
> + bus-width = <8>;
> + };
> + };
> + };
> + };
> +
> + usart1: serial at f0020000 {
> + dmas = <0>, <0>; /* Do not use DMA for usart1 */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
> + status = "okay";
> + };
> +
> + isi: isi at f0034000 {
> + port {
> + isi_0: endpoint {
> + remote-endpoint = <&ov2640_0>;
> + bus-width = <8>;
> + vsync-active = <1>;
> + hsync-active = <1>;
> + };
> + };
> + };
> +
> + mmc1: mmc at f8000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
> + status = "okay";
> + slot at 0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + adc0: adc at f8018000 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <
> + &pinctrl_adc0_adtrg
> + &pinctrl_adc0_ad0
> + &pinctrl_adc0_ad1
> + &pinctrl_adc0_ad2
> + &pinctrl_adc0_ad3
> + &pinctrl_adc0_ad4
> + >;
> + pinctrl-1 = <
> + &pinctrl_adc0_adtrg_sleep
> + &pinctrl_adc0_ad0_sleep
> + &pinctrl_adc0_ad1_sleep
> + &pinctrl_adc0_ad2_sleep
> + &pinctrl_adc0_ad3_sleep
> + &pinctrl_adc0_ad4_sleep
> + >;
> + status = "okay";
> + };
> +
> + macb1: ethernet at f802c000 {
> + phy-mode = "rmii";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy at 1 {
> + /*interrupt-parent = <&pioE>;*/
> + /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
> + reg = <1>;
> + };
> + };
> +
> + pinctrl at fffff200 {
> + adc0 {
> + pinctrl_adc0_adtrg_sleep: adc0_adtrg_1 {
> + atmel,pins =
> + <AT91_PIOD 19 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD19 GPIO output 0 */
> + };
> + pinctrl_adc0_ad0_sleep: adc0_ad0_1 {
> + atmel,pins =
> + <AT91_PIOD 20 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD20 GPIO output 0 */
> + };
> + pinctrl_adc0_ad1_sleep: adc0_ad1_1 {
> + atmel,pins =
> + <AT91_PIOD 21 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD21 GPIO output 0 */
> + };
> + pinctrl_adc0_ad2_sleep: adc0_ad2_1 {
> + atmel,pins =
> + <AT91_PIOD 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD22 GPIO output 0 */
> + };
> + pinctrl_adc0_ad3_sleep: adc0_ad3_1 {
> + atmel,pins =
> + <AT91_PIOD 23 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD23 GPIO output 0 */
> + };
> + pinctrl_adc0_ad4_sleep: adc0_ad4_1 {
> + atmel,pins =
> + <AT91_PIOD 24 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD24 GPIO output 0 */
Please remove all these comments. The binding is good enough to
understand easily.
> + };
> + };
> +
> + board {
> + pinctrl_gpio_keys: gpio_keys {
> + atmel,pins =
> + <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_mmc0_cd: mmc0_cd {
> + atmel,pins =
> + <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
> + };
> +
> + pinctrl_mmc1_cd: mmc1_cd {
> + atmel,pins =
> + <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
> + };
> +
> + pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
> + atmel,pins =
> + <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */
> + };
> +
> + pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
> + atmel,pins =
> + <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */
> + };
> +
> + pinctrl_sensor_reset: sensor_reset-0 {
> + atmel,pins =
> + <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */
> + };
> +
> + pinctrl_sensor_power: sensor_power-0 {
> + atmel,pins =
> + <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
> + };
> +
> + pinctrl_usba_vbus: usba_vbus {
> + atmel,pins =
> + <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
Here again, all comments are not or great use: remove them.
> + };
> + };
> + };
> +
> + dbgu: serial at ffffee00 {
> + dmas = <0>, <0>; /* Do not use DMA for dbgu */
> + status = "okay";
> + };
> +
> + watchdog at fffffe40 {
> + status = "okay";
> + };
> + };
> +
> + usb0: gadget at 00500000 {
> + atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usba_vbus>;
> + status = "okay";
> + };
> + };
> +
> + sound {
> + compatible = "atmel,asoc-wm8904";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
> +
> + atmel,model = "wm8904 @ SAMA5D3EK";
> + atmel,audio-routing =
> + "Headphone Jack", "HPOUTL",
> + "Headphone Jack", "HPOUTR",
> + "IN2L", "Line In Jack",
> + "IN2R", "Line In Jack",
> + "Mic", "MICBIAS",
> + "IN1L", "Mic";
> +
> + atmel,ssc-controller = <&ssc0>;
> + atmel,audio-codec = <&wm8904>;
> +
> + status = "disabled";
> + };
> +
> + /* Conflict with LCD pins */
> + gpio_keys {
> + compatible = "gpio-keys";
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + pb_user1 {
> + label = "pb_user1";
> + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
> + linux,code = <0x100>;
> + gpio-key,wakeup;
> + };
> + };
> +};
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
2016-11-02 3:05 ` Wenyou Yang
(?)
@ 2016-11-14 15:41 ` Sudeep Holla
-1 siblings, 0 replies; 15+ messages in thread
From: Sudeep Holla @ 2016-11-14 15:41 UTC (permalink / raw)
To: Wenyou Yang
Cc: Nicolas Ferre, Alexandre Belloni, Russell King, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Sudeep Holla,
linux-kernel, Wenyou Yang, devicetree, linux-arm-kernel
On 02/11/16 03:05, Wenyou Yang wrote:
> The sama5d36ek CMP board is the variant of sama5d3xek board.
> It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
> some power rail. Its main purpose is used to measure the power
> consumption.
> The difference of the sama5d36ek CMP dts from sama5d36ek dts
> is listed as below.
> 1. The USB host nodes are removed, that is, the USB host is disabled.
> 2. The gpio_keys node is added to wake up from the sleep.
> 3. The LCD isn't supported due to the pins for LCD are conflicted
> with gpio_keys.
> 4. The adc0 node support the pinctrl sleep state to fix the over
> consumption on VDDANA.
>
> As said in errata, "When the USB host ports are used in high speed
> mode (EHCI), it is not possible to suspend the ports if no device is
> attached on each port. This leads to increased power consumption even
> if the system is in a low power mode." That is why the the USB host
> is disabled.
>
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
> ---
>
> Changes in v2:
> - Add the pinctrl sleep state for adc0 node to fix the over
> consumption on VDDANA.
> - Improve the commit log.
>
> arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
> arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
> arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
> 3 files changed, 482 insertions(+)
> create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
> create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
>
[...]
> + /* Conflict with LCD pins */
> + gpio_keys {
> + compatible = "gpio-keys";
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + pb_user1 {
> + label = "pb_user1";
> + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
> + linux,code = <0x100>;
> + gpio-key,wakeup;
Please replace this with "wakeup-source", I will post patches to fix the
new comers in the mainline. It was cleaned last year.
--
Regards,
Sudeep
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-14 15:41 ` Sudeep Holla
0 siblings, 0 replies; 15+ messages in thread
From: Sudeep Holla @ 2016-11-14 15:41 UTC (permalink / raw)
To: Wenyou Yang
Cc: Mark Rutland, devicetree, Russell King, Wenyou Yang, Pawel Moll,
Ian Campbell, Sudeep Holla, Nicolas Ferre, linux-kernel,
Rob Herring, Alexandre Belloni, Kumar Gala, linux-arm-kernel
On 02/11/16 03:05, Wenyou Yang wrote:
> The sama5d36ek CMP board is the variant of sama5d3xek board.
> It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
> some power rail. Its main purpose is used to measure the power
> consumption.
> The difference of the sama5d36ek CMP dts from sama5d36ek dts
> is listed as below.
> 1. The USB host nodes are removed, that is, the USB host is disabled.
> 2. The gpio_keys node is added to wake up from the sleep.
> 3. The LCD isn't supported due to the pins for LCD are conflicted
> with gpio_keys.
> 4. The adc0 node support the pinctrl sleep state to fix the over
> consumption on VDDANA.
>
> As said in errata, "When the USB host ports are used in high speed
> mode (EHCI), it is not possible to suspend the ports if no device is
> attached on each port. This leads to increased power consumption even
> if the system is in a low power mode." That is why the the USB host
> is disabled.
>
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
> ---
>
> Changes in v2:
> - Add the pinctrl sleep state for adc0 node to fix the over
> consumption on VDDANA.
> - Improve the commit log.
>
> arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
> arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
> arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
> 3 files changed, 482 insertions(+)
> create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
> create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
>
[...]
> + /* Conflict with LCD pins */
> + gpio_keys {
> + compatible = "gpio-keys";
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + pb_user1 {
> + label = "pb_user1";
> + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
> + linux,code = <0x100>;
> + gpio-key,wakeup;
Please replace this with "wakeup-source", I will post patches to fix the
new comers in the mainline. It was cleaned last year.
--
Regards,
Sudeep
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board
@ 2016-11-14 15:41 ` Sudeep Holla
0 siblings, 0 replies; 15+ messages in thread
From: Sudeep Holla @ 2016-11-14 15:41 UTC (permalink / raw)
To: linux-arm-kernel
On 02/11/16 03:05, Wenyou Yang wrote:
> The sama5d36ek CMP board is the variant of sama5d3xek board.
> It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
> some power rail. Its main purpose is used to measure the power
> consumption.
> The difference of the sama5d36ek CMP dts from sama5d36ek dts
> is listed as below.
> 1. The USB host nodes are removed, that is, the USB host is disabled.
> 2. The gpio_keys node is added to wake up from the sleep.
> 3. The LCD isn't supported due to the pins for LCD are conflicted
> with gpio_keys.
> 4. The adc0 node support the pinctrl sleep state to fix the over
> consumption on VDDANA.
>
> As said in errata, "When the USB host ports are used in high speed
> mode (EHCI), it is not possible to suspend the ports if no device is
> attached on each port. This leads to increased power consumption even
> if the system is in a low power mode." That is why the the USB host
> is disabled.
>
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
> ---
>
> Changes in v2:
> - Add the pinctrl sleep state for adc0 node to fix the over
> consumption on VDDANA.
> - Improve the commit log.
>
> arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
> arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
> arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
> 3 files changed, 482 insertions(+)
> create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
> create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
>
[...]
> + /* Conflict with LCD pins */
> + gpio_keys {
> + compatible = "gpio-keys";
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + pb_user1 {
> + label = "pb_user1";
> + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
> + linux,code = <0x100>;
> + gpio-key,wakeup;
Please replace this with "wakeup-source", I will post patches to fix the
new comers in the mainline. It was cleaned last year.
--
Regards,
Sudeep
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2016-11-14 15:47 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-11-02 3:05 [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board Wenyou Yang
2016-11-02 3:05 ` Wenyou Yang
2016-11-02 3:05 ` Wenyou Yang
2016-11-02 5:28 ` kbuild test robot
2016-11-02 5:28 ` kbuild test robot
2016-11-02 5:28 ` kbuild test robot
2016-11-02 5:46 ` Wenyou.Yang
2016-11-02 5:46 ` Wenyou.Yang at microchip.com
2016-11-02 5:46 ` Wenyou.Yang-UWL1GkI3JZL3oGB3hsPCZA
2016-11-14 15:36 ` Nicolas Ferre
2016-11-14 15:36 ` Nicolas Ferre
2016-11-14 15:36 ` Nicolas Ferre
2016-11-14 15:41 ` Sudeep Holla
2016-11-14 15:41 ` Sudeep Holla
2016-11-14 15:41 ` Sudeep Holla
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.