* [PATCH v3 0/5] arm64: dts: qcom: sm8450-hdk: enable HDMI output
@ 2022-11-23 21:07 ` Dmitry Baryshkov
0 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: Stephen Boyd, David Airlie, Daniel Vetter, linux-arm-msm,
devicetree, dri-devel, freedreno
Add device tree nodes for MDSS, DPU and DSI devices on Qualcomm SM8450
platform. Enable these devices and add the HDMI bridge configuration on
SM8450 HDK.
Changes since v2:
- Dropped clock-names from mdss device node
- Fixed pinctrl configuration used by lt9611uxc (Krzysztof)
Changes since v1:
- Reorder properties, making status the last one
- Rename opp nodes to follow the schema
- Renamed display-controller and phy device nodes
- Dropped phy-names for DSI PHYs
- Renamed DSI and DSI PHY labels to include mdss_ prefix
- Renamed 3v3 regulator device node to add -regulator suffix
Dmitry Baryshkov (3):
arm64: dts: qcom: sm8450: add RPMH_REGULATOR_LEVEL_LOW_SVS_D1
arm64: dts: qcom: sm8450: add display hardware devices
arm64: dts: qcom: sm8450-hdk: enable display hardware
Vinod Koul (2):
arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge
arm64: dts: qcom: sm8450-hdk: Enable HDMI Display
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 117 +++++++++
arch/arm64/boot/dts/qcom/sm8450.dtsi | 303 +++++++++++++++++++++++-
include/dt-bindings/power/qcom-rpmpd.h | 1 +
3 files changed, 409 insertions(+), 12 deletions(-)
--
2.35.1
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v3 1/5] arm64: dts: qcom: sm8450: add RPMH_REGULATOR_LEVEL_LOW_SVS_D1
2022-11-23 21:07 ` Dmitry Baryshkov
@ 2022-11-23 21:07 ` Dmitry Baryshkov
-1 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: devicetree, linux-arm-msm, dri-devel, Stephen Boyd, freedreno
Add another power saving state used on SM8450. Unfortunately adding it
in proper place causes renumbering of all the opp states in sm8450.dtsi
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 20 ++++++++++++--------
include/dt-bindings/power/qcom-rpmpd.h | 1 +
2 files changed, 13 insertions(+), 8 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index f20db5456765..8cc9f62f7645 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -3211,35 +3211,39 @@ rpmhpd_opp_min_svs: opp2 {
opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
};
- rpmhpd_opp_low_svs: opp3 {
+ rpmhpd_opp_low_svs_d1: opp3 {
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
+ };
+
+ rpmhpd_opp_low_svs: opp4 {
opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
};
- rpmhpd_opp_svs: opp4 {
+ rpmhpd_opp_svs: opp5 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
};
- rpmhpd_opp_svs_l1: opp5 {
+ rpmhpd_opp_svs_l1: opp6 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
};
- rpmhpd_opp_nom: opp6 {
+ rpmhpd_opp_nom: opp7 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
};
- rpmhpd_opp_nom_l1: opp7 {
+ rpmhpd_opp_nom_l1: opp8 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
};
- rpmhpd_opp_nom_l2: opp8 {
+ rpmhpd_opp_nom_l2: opp9 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
};
- rpmhpd_opp_turbo: opp9 {
+ rpmhpd_opp_turbo: opp10 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
};
- rpmhpd_opp_turbo_l1: opp10 {
+ rpmhpd_opp_turbo_l1: opp11 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
};
};
diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
index 7b2e4b66419a..701401c8b945 100644
--- a/include/dt-bindings/power/qcom-rpmpd.h
+++ b/include/dt-bindings/power/qcom-rpmpd.h
@@ -174,6 +174,7 @@
/* SDM845 Power Domain performance levels */
#define RPMH_REGULATOR_LEVEL_RETENTION 16
#define RPMH_REGULATOR_LEVEL_MIN_SVS 48
+#define RPMH_REGULATOR_LEVEL_LOW_SVS_D1 56
#define RPMH_REGULATOR_LEVEL_LOW_SVS 64
#define RPMH_REGULATOR_LEVEL_SVS 128
#define RPMH_REGULATOR_LEVEL_SVS_L0 144
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v3 1/5] arm64: dts: qcom: sm8450: add RPMH_REGULATOR_LEVEL_LOW_SVS_D1
@ 2022-11-23 21:07 ` Dmitry Baryshkov
0 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: Stephen Boyd, David Airlie, Daniel Vetter, linux-arm-msm,
devicetree, dri-devel, freedreno
Add another power saving state used on SM8450. Unfortunately adding it
in proper place causes renumbering of all the opp states in sm8450.dtsi
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 20 ++++++++++++--------
include/dt-bindings/power/qcom-rpmpd.h | 1 +
2 files changed, 13 insertions(+), 8 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index f20db5456765..8cc9f62f7645 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -3211,35 +3211,39 @@ rpmhpd_opp_min_svs: opp2 {
opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
};
- rpmhpd_opp_low_svs: opp3 {
+ rpmhpd_opp_low_svs_d1: opp3 {
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
+ };
+
+ rpmhpd_opp_low_svs: opp4 {
opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
};
- rpmhpd_opp_svs: opp4 {
+ rpmhpd_opp_svs: opp5 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
};
- rpmhpd_opp_svs_l1: opp5 {
+ rpmhpd_opp_svs_l1: opp6 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
};
- rpmhpd_opp_nom: opp6 {
+ rpmhpd_opp_nom: opp7 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
};
- rpmhpd_opp_nom_l1: opp7 {
+ rpmhpd_opp_nom_l1: opp8 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
};
- rpmhpd_opp_nom_l2: opp8 {
+ rpmhpd_opp_nom_l2: opp9 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
};
- rpmhpd_opp_turbo: opp9 {
+ rpmhpd_opp_turbo: opp10 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
};
- rpmhpd_opp_turbo_l1: opp10 {
+ rpmhpd_opp_turbo_l1: opp11 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
};
};
diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
index 7b2e4b66419a..701401c8b945 100644
--- a/include/dt-bindings/power/qcom-rpmpd.h
+++ b/include/dt-bindings/power/qcom-rpmpd.h
@@ -174,6 +174,7 @@
/* SDM845 Power Domain performance levels */
#define RPMH_REGULATOR_LEVEL_RETENTION 16
#define RPMH_REGULATOR_LEVEL_MIN_SVS 48
+#define RPMH_REGULATOR_LEVEL_LOW_SVS_D1 56
#define RPMH_REGULATOR_LEVEL_LOW_SVS 64
#define RPMH_REGULATOR_LEVEL_SVS 128
#define RPMH_REGULATOR_LEVEL_SVS_L0 144
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v3 2/5] arm64: dts: qcom: sm8450: add display hardware devices
2022-11-23 21:07 ` Dmitry Baryshkov
@ 2022-11-23 21:07 ` Dmitry Baryshkov
-1 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: devicetree, linux-arm-msm, dri-devel, Stephen Boyd, freedreno
Add devices tree nodes describing display hardware on SM8450:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs
This does not provide support for DP controllers present on SM8450.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 283 ++++++++++++++++++++++++++-
1 file changed, 279 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 8cc9f62f7645..31fcf3908b2a 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2394,6 +2394,281 @@ camcc: clock-controller@ade0000 {
status = "disabled";
};
+ mdss: mdss@ae00000 {
+ compatible = "qcom,sm8450-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ /* same path used twice */
+ interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>,
+ <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>;
+ interconnect-names = "mdp0-mem", "mdp1-mem";
+
+ resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ iommus = <&apps_smmu 0x2800 0x402>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdss_mdp: display-controller@ae01000 {
+ compatible = "qcom,sm8450-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus",
+ "nrt_bus",
+ "iface",
+ "lut",
+ "core",
+ "vsync";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ operating-points-v2 = <&mdp_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&mdss_dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dpu_intf2_out: endpoint {
+ remote-endpoint = <&mdss_dsi1_in>;
+ };
+ };
+
+ };
+
+ mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-172000000 {
+ opp-hz = /bits/ 64 <172000000>;
+ required-opps = <&rpmhpd_opp_low_svs_d1>;
+ };
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-325000000 {
+ opp-hz = /bits/ 64 <325000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_dsi0: dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+ operating-points-v2 = <&mdss_dsi_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ phys = <&mdss_dsi0_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss_dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mdss_dsi0_out: endpoint {
+ };
+ };
+ };
+
+ mdss_dsi_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-187500000 {
+ opp-hz = /bits/ 64 <187500000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-358000000 {
+ opp-hz = /bits/ 64 <358000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+ };
+
+ mdss_dsi0_phy: phy@ae94400 {
+ compatible = "qcom,dsi-phy-5nm-8450";
+ reg = <0 0x0ae94400 0 0x200>,
+ <0 0x0ae94600 0 0x280>,
+ <0 0x0ae94900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+
+ mdss_dsi1: dsi@ae96000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae96000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;
+
+ operating-points-v2 = <&mdss_dsi_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ phys = <&mdss_dsi1_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss_dsi1_in: endpoint {
+ remote-endpoint = <&dpu_intf2_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mdss_dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ mdss_dsi1_phy: phy@ae96400 {
+ compatible = "qcom,dsi-phy-5nm-8450";
+ reg = <0 0x0ae96400 0 0x200>,
+ <0 0x0ae96600 0 0x280>,
+ <0 0x0ae96900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+ };
+
dispcc: clock-controller@af00000 {
compatible = "qcom,sm8450-dispcc";
reg = <0 0x0af00000 0 0x20000>;
@@ -2401,10 +2676,10 @@ dispcc: clock-controller@af00000 {
<&rpmhcc RPMH_CXO_CLK_A>,
<&gcc GCC_DISP_AHB_CLK>,
<&sleep_clk>,
- <0>, /* dsi0 */
- <0>,
- <0>, /* dsi1 */
- <0>,
+ <&mdss_dsi0_phy 0>,
+ <&mdss_dsi0_phy 1>,
+ <&mdss_dsi1_phy 0>,
+ <&mdss_dsi1_phy 1>,
<0>, /* dp0 */
<0>,
<0>, /* dp1 */
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v3 2/5] arm64: dts: qcom: sm8450: add display hardware devices
@ 2022-11-23 21:07 ` Dmitry Baryshkov
0 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: Stephen Boyd, David Airlie, Daniel Vetter, linux-arm-msm,
devicetree, dri-devel, freedreno
Add devices tree nodes describing display hardware on SM8450:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs
This does not provide support for DP controllers present on SM8450.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 283 ++++++++++++++++++++++++++-
1 file changed, 279 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 8cc9f62f7645..31fcf3908b2a 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2394,6 +2394,281 @@ camcc: clock-controller@ade0000 {
status = "disabled";
};
+ mdss: mdss@ae00000 {
+ compatible = "qcom,sm8450-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ /* same path used twice */
+ interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>,
+ <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>;
+ interconnect-names = "mdp0-mem", "mdp1-mem";
+
+ resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ iommus = <&apps_smmu 0x2800 0x402>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdss_mdp: display-controller@ae01000 {
+ compatible = "qcom,sm8450-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus",
+ "nrt_bus",
+ "iface",
+ "lut",
+ "core",
+ "vsync";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ operating-points-v2 = <&mdp_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&mdss_dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dpu_intf2_out: endpoint {
+ remote-endpoint = <&mdss_dsi1_in>;
+ };
+ };
+
+ };
+
+ mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-172000000 {
+ opp-hz = /bits/ 64 <172000000>;
+ required-opps = <&rpmhpd_opp_low_svs_d1>;
+ };
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-325000000 {
+ opp-hz = /bits/ 64 <325000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_dsi0: dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+ operating-points-v2 = <&mdss_dsi_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ phys = <&mdss_dsi0_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss_dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mdss_dsi0_out: endpoint {
+ };
+ };
+ };
+
+ mdss_dsi_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-187500000 {
+ opp-hz = /bits/ 64 <187500000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-358000000 {
+ opp-hz = /bits/ 64 <358000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+ };
+
+ mdss_dsi0_phy: phy@ae94400 {
+ compatible = "qcom,dsi-phy-5nm-8450";
+ reg = <0 0x0ae94400 0 0x200>,
+ <0 0x0ae94600 0 0x280>,
+ <0 0x0ae94900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+
+ mdss_dsi1: dsi@ae96000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae96000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;
+
+ operating-points-v2 = <&mdss_dsi_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ phys = <&mdss_dsi1_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss_dsi1_in: endpoint {
+ remote-endpoint = <&dpu_intf2_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mdss_dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ mdss_dsi1_phy: phy@ae96400 {
+ compatible = "qcom,dsi-phy-5nm-8450";
+ reg = <0 0x0ae96400 0 0x200>,
+ <0 0x0ae96600 0 0x280>,
+ <0 0x0ae96900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+ };
+
dispcc: clock-controller@af00000 {
compatible = "qcom,sm8450-dispcc";
reg = <0 0x0af00000 0 0x20000>;
@@ -2401,10 +2676,10 @@ dispcc: clock-controller@af00000 {
<&rpmhcc RPMH_CXO_CLK_A>,
<&gcc GCC_DISP_AHB_CLK>,
<&sleep_clk>,
- <0>, /* dsi0 */
- <0>,
- <0>, /* dsi1 */
- <0>,
+ <&mdss_dsi0_phy 0>,
+ <&mdss_dsi0_phy 1>,
+ <&mdss_dsi1_phy 0>,
+ <&mdss_dsi1_phy 1>,
<0>, /* dp0 */
<0>,
<0>, /* dp1 */
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v3 2/5] arm64: dts: qcom: sm8450: add display hardware devices
2022-11-23 21:07 ` Dmitry Baryshkov
@ 2022-12-05 15:40 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2022-12-05 15:40 UTC (permalink / raw)
To: Dmitry Baryshkov, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Rob Clark, Sean Paul, Abhinav Kumar, Rob Herring,
Krzysztof Kozlowski
Cc: Stephen Boyd, David Airlie, Daniel Vetter, linux-arm-msm,
devicetree, dri-devel, freedreno
On 23/11/2022 22:07, Dmitry Baryshkov wrote:
> Add devices tree nodes describing display hardware on SM8450:
> - Display Clock Controller
> - MDSS
> - MDP
> - two DSI controllers and DSI PHYs
>
> This does not provide support for DP controllers present on SM8450.
>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8450.dtsi | 283 ++++++++++++++++++++++++++-
> 1 file changed, 279 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 8cc9f62f7645..31fcf3908b2a 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -2394,6 +2394,281 @@ camcc: clock-controller@ade0000 {
> status = "disabled";
> };
>
> + mdss: mdss@ae00000 {
According to:
https://lore.kernel.org/all/dfd2d1b5-4d1b-2381-ad11-5ea9e6654a55@linaro.org/
this should be "display-subsystem"
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [PATCH v3 2/5] arm64: dts: qcom: sm8450: add display hardware devices
@ 2022-12-05 15:40 ` Krzysztof Kozlowski
0 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2022-12-05 15:40 UTC (permalink / raw)
To: Dmitry Baryshkov, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Rob Clark, Sean Paul, Abhinav Kumar, Rob Herring,
Krzysztof Kozlowski
Cc: devicetree, linux-arm-msm, dri-devel, Stephen Boyd, freedreno
On 23/11/2022 22:07, Dmitry Baryshkov wrote:
> Add devices tree nodes describing display hardware on SM8450:
> - Display Clock Controller
> - MDSS
> - MDP
> - two DSI controllers and DSI PHYs
>
> This does not provide support for DP controllers present on SM8450.
>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8450.dtsi | 283 ++++++++++++++++++++++++++-
> 1 file changed, 279 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 8cc9f62f7645..31fcf3908b2a 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -2394,6 +2394,281 @@ camcc: clock-controller@ade0000 {
> status = "disabled";
> };
>
> + mdss: mdss@ae00000 {
According to:
https://lore.kernel.org/all/dfd2d1b5-4d1b-2381-ad11-5ea9e6654a55@linaro.org/
this should be "display-subsystem"
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v3 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware
2022-11-23 21:07 ` Dmitry Baryshkov
@ 2022-11-23 21:07 ` Dmitry Baryshkov
-1 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: devicetree, linux-arm-msm, dri-devel, Stephen Boyd,
Konrad Dybcio, freedreno
Enable MDSS/DPU/DSI0 on SM8450-HDK device.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 2dd4f8c8f931..75b7aecb7d8e 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -349,6 +349,28 @@ vreg_l7e_2p8: ldo7 {
};
};
+&dispcc {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l6b_1p2>;
+ status = "okay";
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l5b_0p88>;
+ status = "okay";
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
&pcie0 {
status = "okay";
max-link-speed = <2>;
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v3 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware
@ 2022-11-23 21:07 ` Dmitry Baryshkov
0 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: Stephen Boyd, David Airlie, Daniel Vetter, linux-arm-msm,
devicetree, dri-devel, freedreno, Konrad Dybcio
Enable MDSS/DPU/DSI0 on SM8450-HDK device.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 2dd4f8c8f931..75b7aecb7d8e 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -349,6 +349,28 @@ vreg_l7e_2p8: ldo7 {
};
};
+&dispcc {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l6b_1p2>;
+ status = "okay";
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l5b_0p88>;
+ status = "okay";
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
&pcie0 {
status = "okay";
max-link-speed = <2>;
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v3 4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge
2022-11-23 21:07 ` Dmitry Baryshkov
@ 2022-11-23 21:07 ` Dmitry Baryshkov
-1 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: devicetree, linux-arm-msm, dri-devel, Stephen Boyd, Vinod Koul,
freedreno
From: Vinod Koul <vkoul@kernel.org>
Add the LT9611uxc DSI-HDMI bridge and supplies
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 59 +++++++++++++++++++++++++
1 file changed, 59 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 75b7aecb7d8e..d1635c9de6f3 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -20,6 +20,28 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ lt9611_1v2: lt9611-vdd12-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "LT9611_1V2";
+
+ vin-supply = <&vph_pwr>;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ lt9611_3v3: lt9611-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "LT9611_3V3";
+
+ vin-supply = <&vreg_bob>;
+ gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -353,6 +375,27 @@ &dispcc {
status = "okay";
};
+&i2c9 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ lt9611_codec: hdmi-bridge@2b {
+ compatible = "lontium,lt9611uxc";
+ reg = <0x2b>;
+
+ interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
+
+ reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
+
+ vdd-supply = <<9611_1v2>;
+ vcc-supply = <<9611_3v3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
+
+ };
+};
+
&mdss {
status = "okay";
};
@@ -416,6 +459,10 @@ &qupv3_id_0 {
status = "okay";
};
+&qupv3_id_1 {
+ status = "okay";
+};
+
&sdhc_2 {
cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default", "sleep";
@@ -431,6 +478,18 @@ &sdhc_2 {
&tlmm {
gpio-reserved-ranges = <28 4>, <36 4>;
+ lt9611_irq_pin: lt9611-irq-state {
+ pins = "gpio44";
+ function = "gpio";
+ bias-disable;
+ };
+
+ lt9611_rst_pin: lt9611-rst-state {
+ pins = "gpio107";
+ function = "gpio";
+ output-high;
+ };
+
sdc2_card_det_n: sd-card-det-n-state {
pins = "gpio92";
function = "gpio";
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v3 4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge
@ 2022-11-23 21:07 ` Dmitry Baryshkov
0 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: Stephen Boyd, David Airlie, Daniel Vetter, linux-arm-msm,
devicetree, dri-devel, freedreno, Vinod Koul
From: Vinod Koul <vkoul@kernel.org>
Add the LT9611uxc DSI-HDMI bridge and supplies
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 59 +++++++++++++++++++++++++
1 file changed, 59 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 75b7aecb7d8e..d1635c9de6f3 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -20,6 +20,28 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ lt9611_1v2: lt9611-vdd12-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "LT9611_1V2";
+
+ vin-supply = <&vph_pwr>;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ lt9611_3v3: lt9611-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "LT9611_3V3";
+
+ vin-supply = <&vreg_bob>;
+ gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -353,6 +375,27 @@ &dispcc {
status = "okay";
};
+&i2c9 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ lt9611_codec: hdmi-bridge@2b {
+ compatible = "lontium,lt9611uxc";
+ reg = <0x2b>;
+
+ interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
+
+ reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
+
+ vdd-supply = <<9611_1v2>;
+ vcc-supply = <<9611_3v3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
+
+ };
+};
+
&mdss {
status = "okay";
};
@@ -416,6 +459,10 @@ &qupv3_id_0 {
status = "okay";
};
+&qupv3_id_1 {
+ status = "okay";
+};
+
&sdhc_2 {
cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default", "sleep";
@@ -431,6 +478,18 @@ &sdhc_2 {
&tlmm {
gpio-reserved-ranges = <28 4>, <36 4>;
+ lt9611_irq_pin: lt9611-irq-state {
+ pins = "gpio44";
+ function = "gpio";
+ bias-disable;
+ };
+
+ lt9611_rst_pin: lt9611-rst-state {
+ pins = "gpio107";
+ function = "gpio";
+ output-high;
+ };
+
sdc2_card_det_n: sd-card-det-n-state {
pins = "gpio92";
function = "gpio";
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v3 4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge
2022-11-23 21:07 ` Dmitry Baryshkov
@ 2022-12-05 15:42 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2022-12-05 15:42 UTC (permalink / raw)
To: Dmitry Baryshkov, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Rob Clark, Sean Paul, Abhinav Kumar, Rob Herring,
Krzysztof Kozlowski
Cc: Stephen Boyd, David Airlie, Daniel Vetter, linux-arm-msm,
devicetree, dri-devel, freedreno, Vinod Koul
On 23/11/2022 22:07, Dmitry Baryshkov wrote:
> From: Vinod Koul <vkoul@kernel.org>
>
> Add the LT9611uxc DSI-HDMI bridge and supplies
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 59 +++++++++++++++++++++++++
> 1 file changed, 59 insertions(+)
>
(...)
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -353,6 +375,27 @@ &dispcc {
> status = "okay";
> };
>
> +&i2c9 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + lt9611_codec: hdmi-bridge@2b {
> + compatible = "lontium,lt9611uxc";
> + reg = <0x2b>;
> +
> + interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
> +
> + reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
> +
> + vdd-supply = <<9611_1v2>;
> + vcc-supply = <<9611_3v3>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
> +
Drop blank line.
> + };
> +};
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [PATCH v3 4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge
@ 2022-12-05 15:42 ` Krzysztof Kozlowski
0 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2022-12-05 15:42 UTC (permalink / raw)
To: Dmitry Baryshkov, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Rob Clark, Sean Paul, Abhinav Kumar, Rob Herring,
Krzysztof Kozlowski
Cc: devicetree, linux-arm-msm, dri-devel, Stephen Boyd, Vinod Koul,
freedreno
On 23/11/2022 22:07, Dmitry Baryshkov wrote:
> From: Vinod Koul <vkoul@kernel.org>
>
> Add the LT9611uxc DSI-HDMI bridge and supplies
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 59 +++++++++++++++++++++++++
> 1 file changed, 59 insertions(+)
>
(...)
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -353,6 +375,27 @@ &dispcc {
> status = "okay";
> };
>
> +&i2c9 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + lt9611_codec: hdmi-bridge@2b {
> + compatible = "lontium,lt9611uxc";
> + reg = <0x2b>;
> +
> + interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
> +
> + reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
> +
> + vdd-supply = <<9611_1v2>;
> + vcc-supply = <<9611_3v3>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
> +
Drop blank line.
> + };
> +};
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v3 5/5] arm64: dts: qcom: sm8450-hdk: Enable HDMI Display
2022-11-23 21:07 ` Dmitry Baryshkov
@ 2022-11-23 21:07 ` Dmitry Baryshkov
-1 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: devicetree, linux-arm-msm, Krzysztof Kozlowski, dri-devel,
Stephen Boyd, Vinod Koul, freedreno
From: Vinod Koul <vkoul@kernel.org>
Add the HDMI display nodes and link it to DSI.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 36 +++++++++++++++++++++++++
1 file changed, 36 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index d1635c9de6f3..01f65a0e3ca1 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -20,6 +20,17 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <<9611_out>;
+ };
+ };
+ };
+
lt9611_1v2: lt9611-vdd12-regulator {
compatible = "regulator-fixed";
regulator-name = "LT9611_1V2";
@@ -393,6 +404,26 @@ lt9611_codec: hdmi-bridge@2b {
pinctrl-names = "default";
pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lt9611_a: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ lt9611_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
};
};
@@ -405,6 +436,11 @@ &mdss_dsi0 {
status = "okay";
};
+&mdss_dsi0_out {
+ remote-endpoint = <<9611_a>;
+ data-lanes = <0 1 2 3>;
+};
+
&mdss_dsi0_phy {
vdds-supply = <&vreg_l5b_0p88>;
status = "okay";
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v3 5/5] arm64: dts: qcom: sm8450-hdk: Enable HDMI Display
@ 2022-11-23 21:07 ` Dmitry Baryshkov
0 siblings, 0 replies; 16+ messages in thread
From: Dmitry Baryshkov @ 2022-11-23 21:07 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Clark, Sean Paul,
Abhinav Kumar, Rob Herring, Krzysztof Kozlowski
Cc: Stephen Boyd, David Airlie, Daniel Vetter, linux-arm-msm,
devicetree, dri-devel, freedreno, Vinod Koul,
Krzysztof Kozlowski
From: Vinod Koul <vkoul@kernel.org>
Add the HDMI display nodes and link it to DSI.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 36 +++++++++++++++++++++++++
1 file changed, 36 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index d1635c9de6f3..01f65a0e3ca1 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -20,6 +20,17 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <<9611_out>;
+ };
+ };
+ };
+
lt9611_1v2: lt9611-vdd12-regulator {
compatible = "regulator-fixed";
regulator-name = "LT9611_1V2";
@@ -393,6 +404,26 @@ lt9611_codec: hdmi-bridge@2b {
pinctrl-names = "default";
pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lt9611_a: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ lt9611_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
};
};
@@ -405,6 +436,11 @@ &mdss_dsi0 {
status = "okay";
};
+&mdss_dsi0_out {
+ remote-endpoint = <<9611_a>;
+ data-lanes = <0 1 2 3>;
+};
+
&mdss_dsi0_phy {
vdds-supply = <&vreg_l5b_0p88>;
status = "okay";
--
2.35.1
^ permalink raw reply related [flat|nested] 16+ messages in thread