* [PATCH] ASoC: nau8821: new driver
@ 2021-08-09 10:10 Seven Lee
2021-08-09 10:44 ` Amadeusz Sławiński
0 siblings, 1 reply; 8+ messages in thread
From: Seven Lee @ 2021-08-09 10:10 UTC (permalink / raw)
To: broonie
Cc: alsa-devel, scott6986, Seven Lee, KCHSU0, lgirdwood, YHCHuang,
CTLIN0, dardar923, supercraig0719
Add driver for NAU88L21.
Signed-off-by: Seven Lee <wtli@nuvoton.com>
---
.../devicetree/bindings/sound/nau8821.txt | 55 +
sound/soc/codecs/Kconfig | 5 +
sound/soc/codecs/Makefile | 2 +
sound/soc/codecs/nau8821.c | 1818 +++++++++++++++++
sound/soc/codecs/nau8821.h | 533 +++++
5 files changed, 2413 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/nau8821.txt
create mode 100644 sound/soc/codecs/nau8821.c
create mode 100644 sound/soc/codecs/nau8821.h
diff --git a/Documentation/devicetree/bindings/sound/nau8821.txt b/Documentation/devicetree/bindings/sound/nau8821.txt
new file mode 100644
index 000000000000..6c3baf7a5f21
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/nau8821.txt
@@ -0,0 +1,55 @@
+Nuvoton NAU88L21 audio codec
+
+This device supports I2C only.
+
+Required properties:
+ - compatible : Must be "nuvoton,nau8821"
+
+ - reg : the I2C address of the device. This is either 0x1B (CSB=0) or 0x54 (CSB=1).
+
+Optional properties:
+ - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
+ - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
+ otherwise pin in high impedance state.
+ - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
+ - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
+
+ - nuvoton,vref-impedance: VREF Impedance selection
+ 0 - Open
+ 1 - 25 kOhm
+ 2 - 125 kOhm
+ 3 - 2.5 kOhm
+
+ - nuvoton,micbias-voltage: Micbias voltage level.
+ 0 - VDDA
+ 1 - VDDA
+ 2 - VDDA * 1.1
+ 3 - VDDA * 1.2
+ 4 - VDDA * 1.3
+ 5 - VDDA * 1.4
+ 6 - VDDA * 1.53
+ 7 - VDDA * 1.53
+
+ - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+ - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+
+ - nuvoton,dmic-clk-threshold: the ADC threshold of DMIC clock.
+
+
+Example:
+
+ headset: nau8821@1b {
+ compatible = "nuvoton,nau8821";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+ nuvoton,jkdet-enable;
+ nuvoton,jkdet-pull-enable;
+ nuvoton,jkdet-pull-up;
+ nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
+ nuvoton,vref-impedance = <2>;
+ nuvoton,micbias-voltage = <6>;
+ nuvoton,jack-insert-debounce = <7>;
+ nuvoton,jack-eject-debounce = <7>;
+ nuvoton,dmic-clk-threshold = 3072000;
+ };
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index fe5e558635ad..6757f30779ff 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -136,6 +136,7 @@ config SND_SOC_ALL_CODECS
imply SND_SOC_NAU8315
imply SND_SOC_NAU8540
imply SND_SOC_NAU8810
+ imply SND_SOC_NAU8821
imply SND_SOC_NAU8822
imply SND_SOC_NAU8824
imply SND_SOC_NAU8825
@@ -1904,6 +1905,10 @@ config SND_SOC_NAU8810
tristate "Nuvoton Technology Corporation NAU88C10 CODEC"
depends on I2C
+config SND_SOC_NAU8821
+ tristate "Nuvoton Technology Corporation NAU88L21 CODEC"
+ depends on I2C
+
config SND_SOC_NAU8822
tristate "Nuvoton Technology Corporation NAU88C22 CODEC"
depends on I2C
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile
index 8dcea2c4604a..5cb0bbaba1a5 100644
--- a/sound/soc/codecs/Makefile
+++ b/sound/soc/codecs/Makefile
@@ -141,6 +141,7 @@ snd-soc-mt6660-objs := mt6660.o
snd-soc-nau8315-objs := nau8315.o
snd-soc-nau8540-objs := nau8540.o
snd-soc-nau8810-objs := nau8810.o
+snd-soc-nau8821-objs := nau8821.o
snd-soc-nau8822-objs := nau8822.o
snd-soc-nau8824-objs := nau8824.o
snd-soc-nau8825-objs := nau8825.o
@@ -468,6 +469,7 @@ obj-$(CONFIG_SND_SOC_MT6660) += snd-soc-mt6660.o
obj-$(CONFIG_SND_SOC_NAU8315) += snd-soc-nau8315.o
obj-$(CONFIG_SND_SOC_NAU8540) += snd-soc-nau8540.o
obj-$(CONFIG_SND_SOC_NAU8810) += snd-soc-nau8810.o
+obj-$(CONFIG_SND_SOC_NAU8821) += snd-soc-nau8821.o
obj-$(CONFIG_SND_SOC_NAU8822) += snd-soc-nau8822.o
obj-$(CONFIG_SND_SOC_NAU8824) += snd-soc-nau8824.o
obj-$(CONFIG_SND_SOC_NAU8825) += snd-soc-nau8825.o
diff --git a/sound/soc/codecs/nau8821.c b/sound/soc/codecs/nau8821.c
new file mode 100644
index 000000000000..50b89841cfd8
--- /dev/null
+++ b/sound/soc/codecs/nau8821.c
@@ -0,0 +1,1818 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * nau8821.c -- Nuvoton NAU88L21 audio codec driver
+ *
+ * Copyright 2021 Nuvoton Technology Corp.
+ * Author: John Hsu <kchsu0@nuvoton.com>
+ * Co-author: Seven Lee <wtli@nuvoton.com>
+ */
+
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/clk.h>
+#include <linux/acpi.h>
+#include <linux/math64.h>
+#include <linux/semaphore.h>
+#include <sound/initval.h>
+#include <sound/tlv.h>
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/jack.h>
+#include "nau8821.h"
+
+#define NAU_FREF_MAX 13500000
+#define NAU_FVCO_MAX 100000000
+#define NAU_FVCO_MIN 90000000
+
+/* the maximum frequency of CLK_ADC and CLK_DAC */
+#define CLK_DA_AD_MAX 6144000
+
+static int nau8821_configure_sysclk(struct nau8821 *nau8821,
+ int clk_id, unsigned int freq);
+
+struct nau8821_fll {
+ int mclk_src;
+ int ratio;
+ int fll_frac;
+ int fll_int;
+ int clk_ref_div;
+};
+
+struct nau8821_fll_attr {
+ unsigned int param;
+ unsigned int val;
+};
+
+/* scaling for mclk from sysclk_src output */
+static const struct nau8821_fll_attr mclk_src_scaling[] = {
+ { 1, 0x0 },
+ { 2, 0x2 },
+ { 4, 0x3 },
+ { 8, 0x4 },
+ { 16, 0x5 },
+ { 32, 0x6 },
+ { 3, 0x7 },
+ { 6, 0xa },
+ { 12, 0xb },
+ { 24, 0xc },
+ { 48, 0xd },
+ { 96, 0xe },
+ { 5, 0xf },
+};
+
+/* ratio for input clk freq */
+static const struct nau8821_fll_attr fll_ratio[] = {
+ { 512000, 0x01 },
+ { 256000, 0x02 },
+ { 128000, 0x04 },
+ { 64000, 0x08 },
+ { 32000, 0x10 },
+ { 8000, 0x20 },
+ { 4000, 0x40 },
+};
+
+static const struct nau8821_fll_attr fll_pre_scalar[] = {
+ { 0, 0x0 },
+ { 1, 0x1 },
+ { 2, 0x2 },
+ { 3, 0x3 },
+};
+
+/* over sampling rate */
+struct nau8821_osr_attr {
+ unsigned int osr;
+ unsigned int clk_src;
+};
+
+static const struct nau8821_osr_attr osr_dac_sel[] = {
+ { 64, 2 }, /* OSR 64, SRC 1/4 */
+ { 256, 0 }, /* OSR 256, SRC 1 */
+ { 128, 1 }, /* OSR 128, SRC 1/2 */
+ { 0, 0 },
+ { 32, 3 }, /* OSR 32, SRC 1/8 */
+};
+
+static const struct nau8821_osr_attr osr_adc_sel[] = {
+ { 32, 3 }, /* OSR 32, SRC 1/8 */
+ { 64, 2 }, /* OSR 64, SRC 1/4 */
+ { 128, 1 }, /* OSR 128, SRC 1/2 */
+ { 256, 0 }, /* OSR 256, SRC 1 */
+};
+
+struct nau8821_dmic_speed {
+ unsigned int param;
+ unsigned int val;
+};
+
+static const struct nau8821_dmic_speed dmic_speed_sel[] = {
+ { 0, 0x0 }, /*SPEED 1, SRC 1 */
+ { 1, 0x1 }, /*SPEED 2, SRC 1/2 */
+ { 2, 0x2 }, /*SPEED 4, SRC 1/4 */
+ { 3, 0x3 }, /*SPEED 8, SRC 1/8 */
+};
+
+static const struct reg_default nau8821_reg_defaults[] = {
+ { NAU8821_R01_ENA_CTRL, 0x00ff },
+ { NAU8821_R03_CLK_DIVIDER, 0x0050 },
+ { NAU8821_R04_FLL1, 0x0 },
+ { NAU8821_R05_FLL2, 0x00bc },
+ { NAU8821_R06_FLL3, 0x0008 },
+ { NAU8821_R07_FLL4, 0x0010 },
+ { NAU8821_R08_FLL5, 0x4000 },
+ { NAU8821_R09_FLL6, 0x6900 },
+ { NAU8821_R0A_FLL7, 0x0031 },
+ { NAU8821_R0B_FLL8, 0x26e9 },
+ { NAU8821_R0D_JACK_DET_CTRL, 0x0 },
+ { NAU8821_R0F_INTERRUPT_MASK, 0x0 },
+ { NAU8821_R12_INTERRUPT_DIS_CTRL, 0xffff },
+ { NAU8821_R13_DMIC_CTRL, 0x0 },
+ { NAU8821_R1A_GPIO12_CTRL, 0x0 },
+ { NAU8821_R1B_TDM_CTRL, 0x0 },
+ { NAU8821_R1C_I2S_PCM_CTRL1, 0x000a },
+ { NAU8821_R1D_I2S_PCM_CTRL2, 0x8010 },
+ { NAU8821_R1E_LEFT_TIME_SLOT, 0x0 },
+ { NAU8821_R1F_RIGHT_TIME_SLOT, 0x0 },
+ { NAU8821_R21_BIQ0_COF1, 0x0 },
+ { NAU8821_R22_BIQ0_COF2, 0x0 },
+ { NAU8821_R23_BIQ0_COF3, 0x0 },
+ { NAU8821_R24_BIQ0_COF4, 0x0 },
+ { NAU8821_R25_BIQ0_COF5, 0x0 },
+ { NAU8821_R26_BIQ0_COF6, 0x0 },
+ { NAU8821_R27_BIQ0_COF7, 0x0 },
+ { NAU8821_R28_BIQ0_COF8, 0x0 },
+ { NAU8821_R29_BIQ0_COF9, 0x0 },
+ { NAU8821_R2A_BIQ0_COF10, 0x0 },
+ { NAU8821_R2B_ADC_RATE, 0x0002 },
+ { NAU8821_R2C_DAC_CTRL1, 0x0082 },
+ { NAU8821_R2D_DAC_CTRL2, 0x0 },
+ { NAU8821_R2F_DAC_DGAIN_CTRL, 0x0 },
+ { NAU8821_R30_ADC_DGAIN_CTRL, 0x0 },
+ { NAU8821_R31_MUTE_CTRL, 0x0 },
+ { NAU8821_R32_HSVOL_CTRL, 0x0 },
+ { NAU8821_R34_DACR_CTRL, 0xcfcf },
+ { NAU8821_R35_ADC_DGAIN_CTRL1, 0xcfcf },
+ { NAU8821_R36_ADC_DRC_KNEE_IP12, 0x1486 },
+ { NAU8821_R37_ADC_DRC_KNEE_IP34, 0x0f12 },
+ { NAU8821_R38_ADC_DRC_SLOPES, 0x25ff },
+ { NAU8821_R39_ADC_DRC_ATKDCY, 0x3457 },
+ { NAU8821_R3A_DAC_DRC_KNEE_IP12, 0x1486 },
+ { NAU8821_R3B_DAC_DRC_KNEE_IP34, 0x0f12 },
+ { NAU8821_R3C_DAC_DRC_SLOPES, 0x25f9 },
+ { NAU8821_R3D_DAC_DRC_ATKDCY, 0x3457 },
+ { NAU8821_R41_BIQ1_COF1, 0x0 },
+ { NAU8821_R42_BIQ1_COF2, 0x0 },
+ { NAU8821_R43_BIQ1_COF3, 0x0 },
+ { NAU8821_R44_BIQ1_COF4, 0x0 },
+ { NAU8821_R45_BIQ1_COF5, 0x0 },
+ { NAU8821_R46_BIQ1_COF6, 0x0 },
+ { NAU8821_R47_BIQ1_COF7, 0x0 },
+ { NAU8821_R48_BIQ1_COF8, 0x0 },
+ { NAU8821_R49_BIQ1_COF9, 0x0 },
+ { NAU8821_R4A_BIQ1_COF10, 0x0 },
+ { NAU8821_R4B_CLASSG_CTRL, 0x0 },
+ { NAU8821_R4C_IMM_MODE_CTRL, 0x0 },
+ { NAU8821_R4D_IMM_RMS_L, 0x0 },
+ { NAU8821_R53_OTPDOUT_1, 0xaad8 },
+ { NAU8821_R54_OTPDOUT_2, 0x0002 },
+ { NAU8821_R55_MISC_CTRL, 0x0 },
+ { NAU8821_R66_BIAS_ADJ, 0x0 },
+ { NAU8821_R68_TRIM_SETTINGS, 0x0 },
+ { NAU8821_R69_ANALOG_CONTROL_1, 0x0 },
+ { NAU8821_R6A_ANALOG_CONTROL_2, 0x0 },
+ { NAU8821_R6B_PGA_MUTE, 0x0 },
+ { NAU8821_R71_ANALOG_ADC_1, 0x0011 },
+ { NAU8821_R72_ANALOG_ADC_2, 0x0020 },
+ { NAU8821_R73_RDAC, 0x0008 },
+ { NAU8821_R74_MIC_BIAS, 0x0006 },
+ { NAU8821_R76_BOOST, 0x0 },
+ { NAU8821_R77_FEPGA, 0x0 },
+ { NAU8821_R7E_PGA_GAIN, 0x0 },
+ { NAU8821_R7F_POWER_UP_CONTROL, 0x0 },
+ { NAU8821_R80_CHARGE_PUMP, 0x0 },
+};
+
+/**
+ * nau8821_sema_acquire - acquire the semaphore of nau8821
+ * @nau8821: component to register the codec private data with
+ * @timeout: how long in jiffies to wait before failure or zero to wait
+ * until release
+ *
+ * Attempts to acquire the semaphore with number of jiffies. If no more
+ * tasks are allowed to acquire the semaphore, calling this function will
+ * put the task to sleep. If the semaphore is not released within the
+ * specified number of jiffies, this function returns.
+ * If the semaphore is not released within the specified number of jiffies,
+ * this function returns -ETIME. If the sleep is interrupted by a signal,
+ * this function will return -EINTR. It returns 0 if the semaphore was
+ * acquired successfully.
+ *
+ * Acquires the semaphore without jiffies. Try to acquire the semaphore
+ * atomically. Returns 0 if the semaphore has been acquired successfully
+ * or 1 if it cannot be acquired.
+ */
+static int nau8821_sema_acquire(struct nau8821 *nau8821, long timeout)
+{
+ int ret;
+
+ if (!nau8821->irq)
+ return 1;
+
+ if (timeout) {
+ ret = down_timeout(&nau8821->jd_sem, timeout);
+ if (ret < 0)
+ dev_dbg(nau8821->dev, "Acquire semaphore timeout\n");
+ } else {
+ ret = down_trylock(&nau8821->jd_sem);
+ if (ret)
+ dev_dbg(nau8821->dev, "Acquire semaphore fail\n");
+ }
+
+ return ret;
+}
+
+/**
+ * nau8821_sema_release - release the semaphore of nau8821
+ * @nau8821: component to register the codec private data with
+ *
+ * Release the semaphore which may be called from any context and
+ * even by tasks which have never called down().
+ */
+static inline void nau8821_sema_release(struct nau8821 *nau8821)
+{
+ if (!nau8821->irq)
+ return;
+ up(&nau8821->jd_sem);
+}
+
+/**
+ * nau8821_sema_reset - reset the semaphore for nau8821
+ * @nau8821: component to register the codec private data with
+ *
+ * Reset the counter of the semaphore. Call this function to restart
+ * a new round task management.
+ */
+static inline void nau8821_sema_reset(struct nau8821 *nau8821)
+{
+ nau8821->jd_sem.count = 1;
+}
+
+static bool nau8821_readable_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case NAU8821_R00_RESET ... NAU8821_R01_ENA_CTRL:
+ case NAU8821_R03_CLK_DIVIDER ... NAU8821_R0B_FLL8:
+ case NAU8821_R0D_JACK_DET_CTRL:
+ case NAU8821_R0F_INTERRUPT_MASK ... NAU8821_R13_DMIC_CTRL:
+ case NAU8821_R1A_GPIO12_CTRL ... NAU8821_R1F_RIGHT_TIME_SLOT:
+ case NAU8821_R21_BIQ0_COF1 ... NAU8821_R2D_DAC_CTRL2:
+ case NAU8821_R2F_DAC_DGAIN_CTRL ... NAU8821_R32_HSVOL_CTRL:
+ case NAU8821_R34_DACR_CTRL ... NAU8821_R3D_DAC_DRC_ATKDCY:
+ case NAU8821_R41_BIQ1_COF1 ... NAU8821_R4F_FUSE_CTRL3:
+ case NAU8821_R51_FUSE_CTRL1:
+ case NAU8821_R53_OTPDOUT_1 ... NAU8821_R55_MISC_CTRL:
+ case NAU8821_R58_I2C_DEVICE_ID ... NAU8821_R5A_SOFTWARE_RST:
+ case NAU8821_R66_BIAS_ADJ:
+ case NAU8821_R68_TRIM_SETTINGS ... NAU8821_R6B_PGA_MUTE:
+ case NAU8821_R71_ANALOG_ADC_1 ... NAU8821_R74_MIC_BIAS:
+ case NAU8821_R76_BOOST ... NAU8821_R77_FEPGA:
+ case NAU8821_R7E_PGA_GAIN ... NAU8821_R82_GENERAL_STATUS:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static bool nau8821_writeable_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case NAU8821_R00_RESET ... NAU8821_R01_ENA_CTRL:
+ case NAU8821_R03_CLK_DIVIDER ... NAU8821_R0B_FLL8:
+ case NAU8821_R0D_JACK_DET_CTRL:
+ case NAU8821_R0F_INTERRUPT_MASK:
+ case NAU8821_R11_INT_CLR_KEY_STATUS ... NAU8821_R13_DMIC_CTRL:
+ case NAU8821_R1A_GPIO12_CTRL ... NAU8821_R1F_RIGHT_TIME_SLOT:
+ case NAU8821_R21_BIQ0_COF1 ... NAU8821_R2D_DAC_CTRL2:
+ case NAU8821_R2F_DAC_DGAIN_CTRL ... NAU8821_R32_HSVOL_CTRL:
+ case NAU8821_R34_DACR_CTRL ... NAU8821_R3D_DAC_DRC_ATKDCY:
+ case NAU8821_R41_BIQ1_COF1 ... NAU8821_R4C_IMM_MODE_CTRL:
+ case NAU8821_R4E_FUSE_CTRL2 ... NAU8821_R4F_FUSE_CTRL3:
+ case NAU8821_R51_FUSE_CTRL1:
+ case NAU8821_R55_MISC_CTRL:
+ case NAU8821_R5A_SOFTWARE_RST:
+ case NAU8821_R66_BIAS_ADJ:
+ case NAU8821_R68_TRIM_SETTINGS ... NAU8821_R6B_PGA_MUTE:
+ case NAU8821_R71_ANALOG_ADC_1 ... NAU8821_R74_MIC_BIAS:
+ case NAU8821_R76_BOOST ... NAU8821_R77_FEPGA:
+ case NAU8821_R7E_PGA_GAIN ... NAU8821_R80_CHARGE_PUMP:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static bool nau8821_volatile_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case NAU8821_R00_RESET:
+ case NAU8821_R10_IRQ_STATUS ... NAU8821_R11_INT_CLR_KEY_STATUS:
+ case NAU8821_R21_BIQ0_COF1 ... NAU8821_R2A_BIQ0_COF10:
+ case NAU8821_R41_BIQ1_COF1 ... NAU8821_R4A_BIQ1_COF10:
+ case NAU8821_R4D_IMM_RMS_L:
+ case NAU8821_R53_OTPDOUT_1 ... NAU8821_R54_OTPDOUT_2:
+ case NAU8821_R58_I2C_DEVICE_ID ... NAU8821_R5A_SOFTWARE_RST:
+ case NAU8821_R81_CHARGE_PUMP_INPUT_READ ... NAU8821_R82_GENERAL_STATUS:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static int nau8821_biq_coeff_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
+ struct soc_bytes_ext *params = (void *)kcontrol->private_value;
+
+ if (!component->regmap)
+ return -EINVAL;
+
+ regmap_raw_read(component->regmap, NAU8821_R41_BIQ1_COF1,
+ ucontrol->value.bytes.data, params->max);
+
+ return 0;
+}
+
+static int nau8821_biq_coeff_put(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
+ struct soc_bytes_ext *params = (void *)kcontrol->private_value;
+ void *data;
+
+ if (!component->regmap)
+ return -EINVAL;
+
+ data = kmemdup(ucontrol->value.bytes.data,
+ params->max, GFP_KERNEL | GFP_DMA);
+ if (!data)
+ return -ENOMEM;
+
+ regmap_raw_write(component->regmap, NAU8821_R41_BIQ1_COF1,
+ data, params->max);
+
+ kfree(data);
+
+ return 0;
+}
+
+static const char * const nau8821_adc_decimation[] = {
+ "32", "64", "128", "256" };
+
+static const struct soc_enum nau8821_adc_decimation_enum =
+ SOC_ENUM_SINGLE(NAU8821_R2B_ADC_RATE, NAU8821_ADC_SYNC_DOWN_SFT,
+ ARRAY_SIZE(nau8821_adc_decimation), nau8821_adc_decimation);
+
+static const char * const nau8821_dac_oversampl[] = {
+ "64", "256", "128", "", "32" };
+
+static const struct soc_enum nau8821_dac_oversampl_enum =
+ SOC_ENUM_SINGLE(NAU8821_R2C_DAC_CTRL1, NAU8821_DAC_OVERSAMPLE_SFT,
+ ARRAY_SIZE(nau8821_dac_oversampl), nau8821_dac_oversampl);
+
+static const DECLARE_TLV_DB_MINMAX_MUTE(adc_vol_tlv, -6600, 2400);
+static const DECLARE_TLV_DB_MINMAX_MUTE(sidetone_vol_tlv, -4200, 0);
+static const DECLARE_TLV_DB_MINMAX(hp_vol_tlv, -900, 0);
+static const DECLARE_TLV_DB_SCALE(playback_vol_tlv, -6600, 50, 1);
+static const DECLARE_TLV_DB_MINMAX(fepga_gain_tlv, -100, 3600);
+static const DECLARE_TLV_DB_MINMAX_MUTE(crosstalk_vol_tlv, -7000, 2400);
+
+static const struct snd_kcontrol_new nau8821_controls[] = {
+ SOC_DOUBLE_TLV("Mic Volume", NAU8821_R35_ADC_DGAIN_CTRL1,
+ NAU8821_ADCL_CH_VOL_SFT, NAU8821_ADCR_CH_VOL_SFT,
+ 0xff, 0, adc_vol_tlv),
+ SOC_DOUBLE_TLV("Headphone Bypass Volume", NAU8821_R30_ADC_DGAIN_CTRL,
+ 12, 8, 0x0f, 0, sidetone_vol_tlv),
+ SOC_DOUBLE_TLV("Headphone Volume", NAU8821_R32_HSVOL_CTRL,
+ NAU8821_HPL_VOL_SFT, NAU8821_HPR_VOL_SFT, 0x3, 1, hp_vol_tlv),
+ SOC_DOUBLE_TLV("Digital Playback Volume", NAU8821_R34_DACR_CTRL,
+ NAU8821_DACL_CH_VOL_SFT, NAU8821_DACR_CH_VOL_SFT,
+ 0xcf, 0, playback_vol_tlv),
+ SOC_DOUBLE_TLV("Frontend PGA Volume", NAU8821_R7E_PGA_GAIN,
+ NAU8821_PGA_GAIN_L_SFT, NAU8821_PGA_GAIN_R_SFT,
+ 37, 0, fepga_gain_tlv),
+ SOC_DOUBLE_TLV("Headphone Crosstalk Volume",
+ NAU8821_R2F_DAC_DGAIN_CTRL,
+ 0, 8, 0xff, 0, crosstalk_vol_tlv),
+
+ SOC_ENUM("ADC Decimation Rate", nau8821_adc_decimation_enum),
+ SOC_ENUM("DAC Oversampling Rate", nau8821_dac_oversampl_enum),
+ SND_SOC_BYTES_EXT("BIQ Coefficients", 20,
+ nau8821_biq_coeff_get, nau8821_biq_coeff_put),
+};
+
+static const struct snd_kcontrol_new nau8821_adc_ch0_dmic =
+ SOC_DAPM_SINGLE("Switch", NAU8821_R13_DMIC_CTRL,
+ NAU8821_DMIC_EN_SFT, 1, 0);
+
+static int dmic_clock_control(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *k, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ int i, speed_selection, clk_adc_src, clk_adc;
+ unsigned int clk_divider_r03;
+
+ /* The DMIC clock is gotten from adc clock divided by
+ * CLK_DMIC_SRC (1, 2, 4, 8). The clock has to be equal or
+ * less than nau8821->dmic_clk_threshold.
+ */
+ regmap_read(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
+ &clk_divider_r03);
+ clk_adc_src = (clk_divider_r03 & NAU8821_CLK_ADC_SRC_MASK)
+ >> NAU8821_CLK_ADC_SRC_SFT;
+
+ switch (clk_adc_src) {
+ case 0:
+ clk_adc = nau8821->fs * 256;
+ break;
+ case 1:
+ clk_adc = (nau8821->fs * 256) >> 1;
+ break;
+ case 2:
+ clk_adc = (nau8821->fs * 256) >> 2;
+ break;
+ case 3:
+ clk_adc = (nau8821->fs * 256) >> 3;
+ break;
+ }
+
+ for (i = 0 ; i < 4 ; i++) {
+ if ((clk_adc >> dmic_speed_sel[i].param) <=
+ nau8821->dmic_clk_threshold) {
+ speed_selection = dmic_speed_sel[i].val;
+ break;
+ }
+ }
+
+ dev_dbg(nau8821->dev,
+ "clk_adc=%d, dmic_clk_threshold = %d, param=%d, val = %d\n",
+ clk_adc, nau8821->dmic_clk_threshold,
+ dmic_speed_sel[i].param, dmic_speed_sel[i].val);
+ regmap_update_bits(nau8821->regmap, NAU8821_R13_DMIC_CTRL,
+ NAU8821_DMIC_SRC_MASK,
+ (speed_selection << NAU8821_DMIC_SRC_SFT));
+
+ return 0;
+}
+
+static int nau8821_left_adc_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ switch (event) {
+ case SND_SOC_DAPM_POST_PMU:
+ msleep(125);
+ regmap_update_bits(nau8821->regmap, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_ADCL, NAU8821_EN_ADCL);
+ break;
+ case SND_SOC_DAPM_POST_PMD:
+ regmap_update_bits(nau8821->regmap,
+ NAU8821_R01_ENA_CTRL, NAU8821_EN_ADCL, 0);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int nau8821_right_adc_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ switch (event) {
+ case SND_SOC_DAPM_POST_PMU:
+ msleep(125);
+ regmap_update_bits(nau8821->regmap, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_ADCR, NAU8821_EN_ADCR);
+ break;
+ case SND_SOC_DAPM_POST_PMD:
+ regmap_update_bits(nau8821->regmap,
+ NAU8821_R01_ENA_CTRL, NAU8821_EN_ADCR, 0);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int nau8821_pump_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 =
+ snd_soc_component_get_drvdata(component);
+
+ switch (event) {
+ case SND_SOC_DAPM_POST_PMU:
+ /* Prevent startup click by letting charge pump to ramp up */
+ msleep(20);
+ regmap_update_bits(nau8821->regmap, NAU8821_R80_CHARGE_PUMP,
+ NAU8821_JAMNODCLOW, NAU8821_JAMNODCLOW);
+ break;
+ case SND_SOC_DAPM_PRE_PMD:
+ regmap_update_bits(nau8821->regmap, NAU8821_R80_CHARGE_PUMP,
+ NAU8821_JAMNODCLOW, 0);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int nau8821_output_dac_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ switch (event) {
+ case SND_SOC_DAPM_PRE_PMU:
+ /* Disables the TESTDAC to let DAC signal pass through. */
+ regmap_update_bits(nau8821->regmap, NAU8821_R66_BIAS_ADJ,
+ NAU8821_BIAS_TESTDAC_EN, 0);
+ break;
+ case SND_SOC_DAPM_POST_PMD:
+ regmap_update_bits(nau8821->regmap, NAU8821_R66_BIAS_ADJ,
+ NAU8821_BIAS_TESTDAC_EN, NAU8821_BIAS_TESTDAC_EN);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static const struct snd_soc_dapm_widget nau8821_dapm_widgets[] = {
+ SND_SOC_DAPM_SUPPLY("MICBIAS", NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_POWERUP_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA("Frontend PGA L", NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_PGA_L_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA("Frontend PGA R", NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_PGA_R_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_SUPPLY("ADCL Power", NAU8821_R72_ANALOG_ADC_2,
+ NAU8821_POWERUP_ADCL_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_SUPPLY("ADCR Power", NAU8821_R72_ANALOG_ADC_2,
+ NAU8821_POWERUP_ADCR_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_SUPPLY("DMIC Clock", SND_SOC_NOPM, 0, 0,
+ dmic_clock_control, SND_SOC_DAPM_POST_PMU),
+ SND_SOC_DAPM_ADC_E("ADCL", NULL, SND_SOC_NOPM, 0, 0,
+ nau8821_left_adc_event, SND_SOC_DAPM_POST_PMU |
+ SND_SOC_DAPM_POST_PMD),
+ SND_SOC_DAPM_ADC_E("ADCR", NULL, SND_SOC_NOPM, 0, 0,
+ nau8821_right_adc_event, SND_SOC_DAPM_POST_PMU |
+ SND_SOC_DAPM_POST_PMD),
+ SND_SOC_DAPM_SWITCH("DMIC Enable", SND_SOC_NOPM,
+ 0, 0, &nau8821_adc_ch0_dmic),
+ SND_SOC_DAPM_AIF_OUT("AIFTX", "Capture", 0, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_TRISTATE_SFT, 1),
+ SND_SOC_DAPM_AIF_IN("AIFRX", "Playback", 0, SND_SOC_NOPM, 0, 0),
+
+ SND_SOC_DAPM_PGA_S("ADACL", 2, NAU8821_R73_RDAC,
+ NAU8821_DACL_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("ADACR", 2, NAU8821_R73_RDAC,
+ NAU8821_DACR_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("ADACL Clock", 3, NAU8821_R73_RDAC,
+ NAU8821_DACL_CLK_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("ADACR Clock", 3, NAU8821_R73_RDAC,
+ NAU8821_DACR_CLK_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_DAC("DDACR", NULL, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_DACR_SFT, 0),
+ SND_SOC_DAPM_DAC("DDACL", NULL, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_DACL_SFT, 0),
+ SND_SOC_DAPM_PGA_S("HP amp L", 0, NAU8821_R4B_CLASSG_CTRL,
+ NAU8821_CLASSG_LDAC_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("HP amp R", 0, NAU8821_R4B_CLASSG_CTRL,
+ NAU8821_CLASSG_RDAC_EN_SFT, 0, NULL, 0),
+
+ SND_SOC_DAPM_PGA_S("Charge Pump", 1, NAU8821_R80_CHARGE_PUMP,
+ NAU8821_CHANRGE_PUMP_EN_SFT, 0, nau8821_pump_event,
+ SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
+
+ SND_SOC_DAPM_PGA_S("Output Driver R Stage 1", 4,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_INTEG_R_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver L Stage 1", 4,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_INTEG_L_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver R Stage 2", 5,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_DRV_INSTG_R_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver L Stage 2", 5,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_DRV_INSTG_L_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver R Stage 3", 6,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_MAIN_DRV_R_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver L Stage 3", 6,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_MAIN_DRV_L_SFT, 0, NULL, 0),
+
+ SND_SOC_DAPM_PGA_S("Output DACL", 7,
+ NAU8821_R80_CHARGE_PUMP, NAU8821_POWER_DOWN_DACL_SFT,
+ 0, nau8821_output_dac_event,
+ SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
+ SND_SOC_DAPM_PGA_S("Output DACR", 7,
+ NAU8821_R80_CHARGE_PUMP, NAU8821_POWER_DOWN_DACR_SFT,
+ 0, nau8821_output_dac_event,
+ SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
+
+ /* HPOL/R are ungrounded by disabling 16 Ohm pull-downs on playback */
+ SND_SOC_DAPM_PGA_S("HPOL Pulldown", 8,
+ NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_SPKR_DWN1L_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("HPOR Pulldown", 8,
+ NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_SPKR_DWN1R_SFT, 0, NULL, 0),
+
+ /* High current HPOL/R boost driver */
+ SND_SOC_DAPM_PGA_S("HP Boost Driver", 9,
+ NAU8821_R76_BOOST, NAU8821_HP_BOOST_DIS_SFT, 1, NULL, 0),
+
+ SND_SOC_DAPM_PGA("Class G", NAU8821_R4B_CLASSG_CTRL,
+ NAU8821_CLASSG_EN_SFT, 0, NULL, 0),
+
+ SND_SOC_DAPM_INPUT("MICL"),
+ SND_SOC_DAPM_INPUT("MICR"),
+ SND_SOC_DAPM_INPUT("DMIC"),
+ SND_SOC_DAPM_OUTPUT("HPOL"),
+ SND_SOC_DAPM_OUTPUT("HPOR"),
+};
+
+static const struct snd_soc_dapm_route nau8821_dapm_routes[] = {
+ {"Frontend PGA L", NULL, "MICL"},
+ {"Frontend PGA R", NULL, "MICR"},
+
+ {"DMIC Enable", "Switch", "DMIC"},
+ {"DMIC Enable", NULL, "DMIC Clock"},
+ {"ADCL", NULL, "DMIC Enable"},
+ {"ADCR", NULL, "DMIC Enable"},
+
+ {"Frontend PGA L", NULL, "ADCL Power"},
+ {"Frontend PGA R", NULL, "ADCR Power"},
+ {"Frontend PGA L", NULL, "MICBIAS"},
+ {"Frontend PGA R", NULL, "MICBIAS"},
+
+ {"ADCL", NULL, "Frontend PGA L"},
+ {"ADCR", NULL, "Frontend PGA R"},
+
+ {"AIFTX", NULL, "ADCL"},
+ {"AIFTX", NULL, "ADCR"},
+ {"AIFTX", NULL, "DMIC Enable"},
+
+ {"DDACL", NULL, "AIFRX"},
+ {"DDACR", NULL, "AIFRX"},
+
+ {"HP amp L", NULL, "DDACL"},
+ {"HP amp R", NULL, "DDACR"},
+ {"Charge Pump", NULL, "HP amp L"},
+ {"Charge Pump", NULL, "HP amp R"},
+ {"ADACL", NULL, "Charge Pump"},
+ {"ADACR", NULL, "Charge Pump"},
+ {"ADACL Clock", NULL, "ADACL"},
+ {"ADACR Clock", NULL, "ADACR"},
+ {"Output Driver L Stage 1", NULL, "ADACL Clock"},
+ {"Output Driver R Stage 1", NULL, "ADACR Clock"},
+ {"Output Driver L Stage 2", NULL, "Output Driver L Stage 1"},
+ {"Output Driver R Stage 2", NULL, "Output Driver R Stage 1"},
+ {"Output Driver L Stage 3", NULL, "Output Driver L Stage 2"},
+ {"Output Driver R Stage 3", NULL, "Output Driver R Stage 2"},
+ {"Output DACL", NULL, "Output Driver L Stage 3"},
+ {"Output DACR", NULL, "Output Driver R Stage 3"},
+ {"HPOL Pulldown", NULL, "Output DACL"},
+ {"HPOR Pulldown", NULL, "Output DACR"},
+ {"HP Boost Driver", NULL, "HPOL Pulldown"},
+ {"HP Boost Driver", NULL, "HPOR Pulldown"},
+ {"Class G", NULL, "HP Boost Driver"},
+ {"HPOL", NULL, "Class G"},
+ {"HPOR", NULL, "Class G"},
+};
+
+static int nau8821_clock_check(struct nau8821 *nau8821,
+ int stream, int rate, int osr)
+{
+ int osrate = 0;
+
+ if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
+ if (osr >= ARRAY_SIZE(osr_dac_sel))
+ return -EINVAL;
+ osrate = osr_dac_sel[osr].osr;
+ } else {
+ if (osr >= ARRAY_SIZE(osr_adc_sel))
+ return -EINVAL;
+ osrate = osr_adc_sel[osr].osr;
+ }
+
+ if (!osrate || rate * osrate > CLK_DA_AD_MAX) {
+ dev_err(nau8821->dev,
+ "exceed the maximum frequency of CLK_ADC or CLK_DAC\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int nau8821_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params, struct snd_soc_dai *dai)
+{
+ struct snd_soc_component *component = dai->component;
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ unsigned int val_len = 0, osr, ctrl_val, bclk_fs, clk_div;
+
+ nau8821_sema_acquire(nau8821, HZ);
+ nau8821->fs = params_rate(params);
+ /* CLK_DAC or CLK_ADC = OSR * FS
+ * DAC or ADC clock frequency is defined as Over Sampling Rate (OSR)
+ * multiplied by the audio sample rate (Fs). Note that the OSR and Fs
+ * values must be selected such that the maximum frequency is less
+ * than 6.144 MHz.
+ */
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
+ regmap_read(nau8821->regmap, NAU8821_R2C_DAC_CTRL1, &osr);
+ osr &= NAU8821_DAC_OVERSAMPLE_MASK;
+ if (nau8821_clock_check(nau8821, substream->stream,
+ nau8821->fs, osr)) {
+ nau8821_sema_release(nau8821);
+ return -EINVAL;
+ }
+ regmap_update_bits(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_DAC_SRC_MASK,
+ osr_dac_sel[osr].clk_src << NAU8821_CLK_DAC_SRC_SFT);
+ } else {
+ regmap_read(nau8821->regmap, NAU8821_R2B_ADC_RATE, &osr);
+ osr &= NAU8821_ADC_SYNC_DOWN_MASK;
+ if (nau8821_clock_check(nau8821, substream->stream,
+ nau8821->fs, osr)) {
+ nau8821_sema_release(nau8821);
+ return -EINVAL;
+ }
+ regmap_update_bits(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_ADC_SRC_MASK,
+ osr_adc_sel[osr].clk_src << NAU8821_CLK_ADC_SRC_SFT);
+ }
+
+ /* make BCLK and LRC divde configuration if the codec as master. */
+ regmap_read(nau8821->regmap, NAU8821_R1D_I2S_PCM_CTRL2, &ctrl_val);
+ if (ctrl_val & NAU8821_I2S_MS_MASTER) {
+ /* get the bclk and fs ratio */
+ bclk_fs = snd_soc_params_to_bclk(params) / nau8821->fs;
+ if (bclk_fs <= 32)
+ clk_div = 3;
+ else if (bclk_fs <= 64)
+ clk_div = 2;
+ else if (bclk_fs <= 128)
+ clk_div = 1;
+ else {
+ nau8821_sema_release(nau8821);
+ return -EINVAL;
+ }
+ regmap_update_bits(nau8821->regmap, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_LRC_DIV_MASK | NAU8821_I2S_BLK_DIV_MASK,
+ (clk_div << NAU8821_I2S_LRC_DIV_SFT) | clk_div);
+ }
+
+ switch (params_width(params)) {
+ case 16:
+ val_len |= NAU8821_I2S_DL_16;
+ break;
+ case 20:
+ val_len |= NAU8821_I2S_DL_20;
+ break;
+ case 24:
+ val_len |= NAU8821_I2S_DL_24;
+ break;
+ case 32:
+ val_len |= NAU8821_I2S_DL_32;
+ break;
+ default:
+ nau8821_sema_release(nau8821);
+ return -EINVAL;
+ }
+
+ regmap_update_bits(nau8821->regmap, NAU8821_R1C_I2S_PCM_CTRL1,
+ NAU8821_I2S_DL_MASK, val_len);
+
+ nau8821_sema_release(nau8821);
+
+ return 0;
+}
+
+static int nau8821_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt)
+{
+ struct snd_soc_component *component = codec_dai->component;
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ unsigned int ctrl1_val = 0, ctrl2_val = 0;
+
+ switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+ case SND_SOC_DAIFMT_CBM_CFM:
+ ctrl2_val |= NAU8821_I2S_MS_MASTER;
+ break;
+ case SND_SOC_DAIFMT_CBS_CFS:
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ case SND_SOC_DAIFMT_NB_NF:
+ break;
+ case SND_SOC_DAIFMT_IB_NF:
+ ctrl1_val |= NAU8821_I2S_BP_INV;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+ case SND_SOC_DAIFMT_I2S:
+ ctrl1_val |= NAU8821_I2S_DF_I2S;
+ break;
+ case SND_SOC_DAIFMT_LEFT_J:
+ ctrl1_val |= NAU8821_I2S_DF_LEFT;
+ break;
+ case SND_SOC_DAIFMT_RIGHT_J:
+ ctrl1_val |= NAU8821_I2S_DF_RIGTH;
+ break;
+ case SND_SOC_DAIFMT_DSP_A:
+ ctrl1_val |= NAU8821_I2S_DF_PCM_AB;
+ break;
+ case SND_SOC_DAIFMT_DSP_B:
+ ctrl1_val |= NAU8821_I2S_DF_PCM_AB;
+ ctrl1_val |= NAU8821_I2S_PCMB_EN;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ nau8821_sema_acquire(nau8821, HZ);
+
+ regmap_update_bits(nau8821->regmap, NAU8821_R1C_I2S_PCM_CTRL1,
+ NAU8821_I2S_DL_MASK | NAU8821_I2S_DF_MASK |
+ NAU8821_I2S_BP_MASK | NAU8821_I2S_PCMB_MASK, ctrl1_val);
+ regmap_update_bits(nau8821->regmap, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_MS_MASK, ctrl2_val);
+
+ nau8821_sema_release(nau8821);
+
+ return 0;
+}
+
+static int nau8821_digital_mute(struct snd_soc_dai *dai, int mute,
+ int direction)
+{
+ struct snd_soc_component *component = dai->component;
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ unsigned int val = 0;
+
+ if (mute)
+ val = NAU8821_DAC_SOFT_MUTE;
+
+ return regmap_update_bits(nau8821->regmap,
+ NAU8821_R31_MUTE_CTRL, NAU8821_DAC_SOFT_MUTE, val);
+}
+
+static const struct snd_soc_dai_ops nau8821_dai_ops = {
+ .hw_params = nau8821_hw_params,
+ .set_fmt = nau8821_set_dai_fmt,
+ .mute_stream = nau8821_digital_mute,
+};
+
+#define NAU8821_RATES SNDRV_PCM_RATE_8000_192000
+#define NAU8821_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE \
+ | SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S32_LE)
+
+static struct snd_soc_dai_driver nau8821_dai = {
+ .name = NUVOTON_CODEC_DAI,
+ .playback = {
+ .stream_name = "Playback",
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = NAU8821_RATES,
+ .formats = NAU8821_FORMATS,
+ },
+ .capture = {
+ .stream_name = "Capture",
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = NAU8821_RATES,
+ .formats = NAU8821_FORMATS,
+ },
+ .ops = &nau8821_dai_ops,
+};
+
+
+static bool nau8821_is_jack_inserted(struct regmap *regmap)
+{
+ bool active_high, is_high;
+ int status, jkdet;
+
+ regmap_read(regmap, NAU8821_R0D_JACK_DET_CTRL, &jkdet);
+ active_high = jkdet & NAU8821_JACK_POLARITY;
+ regmap_read(regmap, NAU8821_R82_GENERAL_STATUS, &status);
+ is_high = status & NAU8821_GPIO2_IN;
+ /* return jack connection status according to jack insertion logic
+ * active high or active low.
+ */
+ return active_high == is_high;
+}
+
+static void nau8821_int_status_clear_all(struct regmap *regmap)
+{
+ int active_irq, clear_irq, i;
+
+ /* Reset the intrruption status from rightmost bit if the corres-
+ * ponding irq event occurs.
+ */
+ regmap_read(regmap, NAU8821_R10_IRQ_STATUS, &active_irq);
+ for (i = 0; i < NAU8821_REG_DATA_LEN; i++) {
+ clear_irq = (0x1 << i);
+ if (active_irq & clear_irq)
+ regmap_write(regmap,
+ NAU8821_R11_INT_CLR_KEY_STATUS, clear_irq);
+ }
+}
+
+static void nau8821_eject_jack(struct nau8821 *nau8821)
+{
+ struct snd_soc_dapm_context *dapm = nau8821->dapm;
+ struct regmap *regmap = nau8821->regmap;
+
+ /* Reset semaphore */
+ nau8821_sema_reset(nau8821);
+
+ /* Detach 2kOhm Resistors from MICBIAS to MICGND */
+ regmap_update_bits(regmap, NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_JKR2, 0);
+ /* HPL/HPR short to ground */
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_SPKR_DWN1R | NAU8821_SPKR_DWN1L, 0);
+ snd_soc_dapm_disable_pin(dapm, "MICBIAS");
+ snd_soc_dapm_sync(dapm);
+
+ /* Clear all interruption status */
+ nau8821_int_status_clear_all(regmap);
+
+ /* Enable the insertion interruption, disable the ejection inter-
+ * ruption, and then bypass de-bounce circuit.
+ */
+ regmap_update_bits(regmap, NAU8821_R12_INTERRUPT_DIS_CTRL,
+ NAU8821_IRQ_EJECT_DIS | NAU8821_IRQ_INSERT_DIS,
+ NAU8821_IRQ_EJECT_DIS);
+ /* Mask unneeded IRQs: 1 - disable, 0 - enable */
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_EJECT_EN | NAU8821_IRQ_INSERT_EN,
+ NAU8821_IRQ_EJECT_EN);
+
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_DET_DB_BYPASS, NAU8821_JACK_DET_DB_BYPASS);
+
+ /* Close clock for jack type detection at manual mode */
+ if (dapm->bias_level < SND_SOC_BIAS_PREPARE)
+ nau8821_configure_sysclk(nau8821, NAU8821_CLK_DIS, 0);
+
+ /* Recover to normal channel input */
+ regmap_update_bits(regmap, NAU8821_R2B_ADC_RATE,
+ NAU8821_ADC_R_SRC_EN, 0);
+}
+
+static void nau8821_jdet_work(struct work_struct *work)
+{
+ struct nau8821 *nau8821 =
+ container_of(work, struct nau8821, jdet_work);
+ struct snd_soc_dapm_context *dapm = nau8821->dapm;
+ struct regmap *regmap = nau8821->regmap;
+ int jack_status_reg, mic_detected, event = 0, event_mask = 0;
+
+ snd_soc_dapm_force_enable_pin(dapm, "MICBIAS");
+ snd_soc_dapm_sync(dapm);
+ msleep(20);
+
+ regmap_read(regmap, NAU8821_R58_I2C_DEVICE_ID, &jack_status_reg);
+ mic_detected = !(jack_status_reg & NAU8821_KEYDET);
+
+ if (mic_detected) {
+ dev_dbg(nau8821->dev, "Headset connected\n");
+ event |= SND_JACK_HEADSET;
+
+ /* 2kOhm Resistor from MICBIAS to MICGND1 */
+ regmap_update_bits(regmap, NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_JKR2, NAU8821_MICBIAS_JKR2);
+ /* Latch Right Channel Analog data
+ * input into the Right Channel Filter
+ */
+ regmap_update_bits(regmap, NAU8821_R2B_ADC_RATE,
+ NAU8821_ADC_R_SRC_EN, NAU8821_ADC_R_SRC_EN);
+ } else {
+ dev_dbg(nau8821->dev, "Headphone connected\n");
+ event |= SND_JACK_HEADPHONE;
+ snd_soc_dapm_disable_pin(dapm, "MICBIAS");
+ snd_soc_dapm_sync(dapm);
+ }
+ event_mask |= SND_JACK_HEADSET;
+ snd_soc_jack_report(nau8821->jack, event, event_mask);
+ nau8821_sema_release(nau8821);
+}
+
+/* Enable interruptions with internal clock. */
+static void nau8821_setup_inserted_irq(struct nau8821 *nau8821)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ /* Enable internal VCO needed for interruptions */
+ if (nau8821->dapm->bias_level < SND_SOC_BIAS_PREPARE)
+ nau8821_configure_sysclk(nau8821, NAU8821_CLK_INTERNAL, 0);
+
+ /* Chip needs one FSCLK cycle in order to generate interruptions,
+ * as we cannot guarantee one will be provided by the system. Turning
+ * master mode on then off enables us to generate that FSCLK cycle
+ * with a minimum of contention on the clock bus.
+ */
+ regmap_update_bits(regmap, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_MS_MASK, NAU8821_I2S_MS_MASTER);
+ regmap_update_bits(regmap, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_MS_MASK, NAU8821_I2S_MS_SLAVE);
+
+ /* Not bypass de-bounce circuit */
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_DET_DB_BYPASS, 0);
+
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_EJECT_EN, 0);
+ regmap_update_bits(regmap, NAU8821_R12_INTERRUPT_DIS_CTRL,
+ NAU8821_IRQ_EJECT_DIS, 0);
+}
+
+static irqreturn_t nau8821_interrupt(int irq, void *data)
+{
+ struct nau8821 *nau8821 = (struct nau8821 *)data;
+ struct regmap *regmap = nau8821->regmap;
+ int active_irq, clear_irq = 0, event = 0, event_mask = 0;
+
+ if (regmap_read(regmap, NAU8821_R10_IRQ_STATUS, &active_irq)) {
+ dev_err(nau8821->dev, "failed to read irq status\n");
+ return IRQ_NONE;
+ }
+
+ dev_dbg(nau8821->dev, "IRQ %d\n", active_irq);
+
+ if ((active_irq & NAU8821_JACK_EJECT_IRQ_MASK) ==
+ NAU8821_JACK_EJECT_DETECTED) {
+ regmap_update_bits(regmap, NAU8821_R71_ANALOG_ADC_1,
+ NAU8821_MICDET_MASK, NAU8821_MICDET_DIS);
+ nau8821_eject_jack(nau8821);
+ event_mask |= SND_JACK_HEADSET;
+ clear_irq = NAU8821_JACK_EJECT_IRQ_MASK;
+ } else if ((active_irq & NAU8821_JACK_INSERT_IRQ_MASK) ==
+ NAU8821_JACK_INSERT_DETECTED) {
+ regmap_update_bits(regmap, NAU8821_R71_ANALOG_ADC_1,
+ NAU8821_MICDET_MASK, NAU8821_MICDET_EN);
+ if (nau8821_is_jack_inserted(regmap)) {
+ /* detect microphone and jack type */
+ cancel_work_sync(&nau8821->jdet_work);
+ schedule_work(&nau8821->jdet_work);
+ /* Turn off insertion interruption at manual mode */
+ regmap_update_bits(regmap,
+ NAU8821_R12_INTERRUPT_DIS_CTRL,
+ NAU8821_IRQ_INSERT_DIS,
+ NAU8821_IRQ_INSERT_DIS);
+ regmap_update_bits(regmap,
+ NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_INSERT_EN,
+ NAU8821_IRQ_INSERT_EN);
+ nau8821_setup_inserted_irq(nau8821);
+ } else {
+ dev_warn(nau8821->dev,
+ "Inserted IRQ fired but not connected\n");
+ nau8821_eject_jack(nau8821);
+ }
+ }
+
+ if (!clear_irq)
+ clear_irq = active_irq;
+ /* clears the rightmost interruption */
+ regmap_write(regmap, NAU8821_R11_INT_CLR_KEY_STATUS, clear_irq);
+
+ if (event_mask)
+ snd_soc_jack_report(nau8821->jack, event, event_mask);
+
+ return IRQ_HANDLED;
+}
+
+static const struct regmap_config nau8821_regmap_config = {
+ .val_bits = NAU8821_REG_DATA_LEN,
+ .reg_bits = NAU8821_REG_ADDR_LEN,
+
+ .max_register = NAU8821_REG_MAX,
+ .readable_reg = nau8821_readable_reg,
+ .writeable_reg = nau8821_writeable_reg,
+ .volatile_reg = nau8821_volatile_reg,
+
+ .cache_type = REGCACHE_RBTREE,
+ .reg_defaults = nau8821_reg_defaults,
+ .num_reg_defaults = ARRAY_SIZE(nau8821_reg_defaults),
+};
+
+static int nau8821_component_probe(struct snd_soc_component *component)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ struct snd_soc_dapm_context *dapm =
+ snd_soc_component_get_dapm(component);
+
+ nau8821->dapm = dapm;
+
+ return 0;
+}
+
+static void nau8821_component_remove(struct snd_soc_component *component)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ if (nau8821->irq)
+ /* Reset semaphore */
+ nau8821_sema_reset(nau8821);
+}
+
+/**
+ * nau8821_calc_fll_param - Calculate FLL parameters.
+ * @fll_in: external clock provided to codec.
+ * @fs: sampling rate.
+ * @fll_param: Pointer to structure of FLL parameters.
+ *
+ * Calculate FLL parameters to configure codec.
+ *
+ * Returns 0 for success or negative error code.
+ */
+static int nau8821_calc_fll_param(unsigned int fll_in,
+ unsigned int fs, struct nau8821_fll *fll_param)
+{
+ u64 fvco, fvco_max;
+ unsigned int fref, i, fvco_sel;
+
+ /* Ensure the reference clock frequency (FREF) is <= 13.5MHz by
+ * dividing freq_in by 1, 2, 4, or 8 using FLL pre-scalar.
+ * FREF = freq_in / NAU8821_FLL_REF_DIV_MASK
+ */
+ for (i = 0; i < ARRAY_SIZE(fll_pre_scalar); i++) {
+ fref = fll_in >> fll_pre_scalar[i].param;
+ if (fref <= NAU_FREF_MAX)
+ break;
+ }
+ if (i == ARRAY_SIZE(fll_pre_scalar))
+ return -EINVAL;
+ fll_param->clk_ref_div = fll_pre_scalar[i].val;
+
+ /* Choose the FLL ratio based on FREF */
+ for (i = 0; i < ARRAY_SIZE(fll_ratio); i++) {
+ if (fref >= fll_ratio[i].param)
+ break;
+ }
+ if (i == ARRAY_SIZE(fll_ratio))
+ return -EINVAL;
+ fll_param->ratio = fll_ratio[i].val;
+
+ /* Calculate the frequency of DCO (FDCO) given freq_out = 256 * Fs.
+ * FDCO must be within the 90MHz - 100MHz or the FFL cannot be
+ * guaranteed across the full range of operation.
+ * FDCO = freq_out * 2 * mclk_src_scaling
+ */
+ fvco_max = 0;
+ fvco_sel = ARRAY_SIZE(mclk_src_scaling);
+ for (i = 0; i < ARRAY_SIZE(mclk_src_scaling); i++) {
+ fvco = 256ULL * fs * 2 * mclk_src_scaling[i].param;
+ if (fvco > NAU_FVCO_MIN && fvco < NAU_FVCO_MAX &&
+ fvco_max < fvco) {
+ fvco_max = fvco;
+ fvco_sel = i;
+ }
+ }
+ if (ARRAY_SIZE(mclk_src_scaling) == fvco_sel)
+ return -EINVAL;
+ fll_param->mclk_src = mclk_src_scaling[fvco_sel].val;
+
+ /* Calculate the FLL 10-bit integer input and the FLL 24-bit fractional
+ * input based on FDCO, FREF and FLL ratio.
+ */
+ fvco = div_u64(fvco_max << 24, fref * fll_param->ratio);
+ fll_param->fll_int = (fvco >> 24) & 0x3ff;
+ fll_param->fll_frac = fvco & 0xffffff;
+
+ return 0;
+}
+
+static void nau8821_fll_apply(struct nau8821 *nau8821,
+ struct nau8821_fll *fll_param)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_SRC_MASK | NAU8821_CLK_MCLK_SRC_MASK,
+ NAU8821_CLK_SRC_MCLK | fll_param->mclk_src);
+ /* Make DSP operate at high speed for better performance. */
+ regmap_update_bits(regmap, NAU8821_R04_FLL1,
+ NAU8821_FLL_RATIO_MASK | NAU8821_ICTRL_LATCH_MASK,
+ fll_param->ratio | (0x6 << NAU8821_ICTRL_LATCH_SFT));
+ /* FLL 24-bit fractional input */
+ regmap_write(regmap, NAU8821_R0A_FLL7,
+ (fll_param->fll_frac >> 16) & 0xff);
+ regmap_write(regmap, NAU8821_R0B_FLL8, fll_param->fll_frac & 0xffff);
+ /* FLL 10-bit integer input */
+ regmap_update_bits(regmap, NAU8821_R06_FLL3,
+ NAU8821_FLL_INTEGER_MASK, fll_param->fll_int);
+ /* FLL pre-scaler */
+ regmap_update_bits(regmap, NAU8821_R07_FLL4,
+ NAU8821_HIGHBW_EN | NAU8821_FLL_REF_DIV_MASK,
+ NAU8821_HIGHBW_EN |
+ (fll_param->clk_ref_div << NAU8821_FLL_REF_DIV_SFT));
+ /* select divided VCO input */
+ regmap_update_bits(regmap, NAU8821_R08_FLL5,
+ NAU8821_FLL_CLK_SW_MASK, NAU8821_FLL_CLK_SW_REF);
+ /* Disable free-running mode */
+ regmap_update_bits(regmap,
+ NAU8821_R09_FLL6, NAU8821_DCO_EN, 0);
+ if (fll_param->fll_frac) {
+ /* set FLL loop filter enable and cutoff frequency at 500Khz */
+ regmap_update_bits(regmap, NAU8821_R08_FLL5,
+ NAU8821_FLL_PDB_DAC_EN | NAU8821_FLL_LOOP_FTR_EN |
+ NAU8821_FLL_FTR_SW_MASK,
+ NAU8821_FLL_PDB_DAC_EN | NAU8821_FLL_LOOP_FTR_EN |
+ NAU8821_FLL_FTR_SW_FILTER);
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_SDM_EN | NAU8821_CUTOFF500,
+ NAU8821_SDM_EN | NAU8821_CUTOFF500);
+ } else {
+ /* disable FLL loop filter and cutoff frequency */
+ regmap_update_bits(regmap, NAU8821_R08_FLL5,
+ NAU8821_FLL_PDB_DAC_EN | NAU8821_FLL_LOOP_FTR_EN |
+ NAU8821_FLL_FTR_SW_MASK, NAU8821_FLL_FTR_SW_ACCU);
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_SDM_EN | NAU8821_CUTOFF500, 0);
+ }
+}
+
+/**
+ * nau8821_set_fll - FLL configuration of nau8821
+ * @codec: codec component
+ * @freq_in: frequency of input clock source
+ * @freq_out: must be 256*Fs in order to achieve the best performance
+ *
+ * The FLL function can select BCLK or MCLK as the input clock source.
+ *
+ * Returns 0 if the parameters have been applied successfully
+ * or negative error code.
+ */
+static int nau8821_set_fll(struct snd_soc_component *component,
+ int pll_id, int source, unsigned int freq_in, unsigned int freq_out)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ struct nau8821_fll fll_set_param, *fll_param = &fll_set_param;
+ int ret, fs;
+
+ fs = freq_out >> 8;
+ ret = nau8821_calc_fll_param(freq_in, fs, fll_param);
+ if (ret) {
+ dev_err(nau8821->dev,
+ "Unsupported input clock %d to output clock %d\n",
+ freq_in, freq_out);
+ return ret;
+ }
+ dev_dbg(nau8821->dev,
+ "mclk_src=%x ratio=%x fll_frac=%x fll_int=%x clk_ref_div=%x\n",
+ fll_param->mclk_src, fll_param->ratio, fll_param->fll_frac,
+ fll_param->fll_int, fll_param->clk_ref_div);
+
+ nau8821_fll_apply(nau8821, fll_param);
+ mdelay(2);
+ regmap_update_bits(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_SRC_MASK, NAU8821_CLK_SRC_VCO);
+
+ return 0;
+}
+
+static void nau8821_configure_mclk_as_sysclk(struct regmap *regmap)
+{
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_SRC_MASK, NAU8821_CLK_SRC_MCLK);
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_DCO_EN, 0);
+ /* Make DSP operate as default setting for power saving. */
+ regmap_update_bits(regmap, NAU8821_R04_FLL1,
+ NAU8821_ICTRL_LATCH_MASK, 0);
+}
+
+static int nau8821_configure_sysclk(struct nau8821 *nau8821,
+ int clk_id, unsigned int freq)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ switch (clk_id) {
+ case NAU8821_CLK_DIS:
+ /* Clock provided externally and disable internal VCO clock */
+ nau8821_configure_mclk_as_sysclk(regmap);
+ break;
+ case NAU8821_CLK_MCLK:
+ nau8821_sema_acquire(nau8821, HZ);
+ nau8821_configure_mclk_as_sysclk(regmap);
+ /* MCLK not changed by clock tree */
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_MCLK_SRC_MASK, 0);
+ nau8821_sema_release(nau8821);
+ break;
+ case NAU8821_CLK_INTERNAL:
+ if (nau8821_is_jack_inserted(regmap)) {
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_DCO_EN, NAU8821_DCO_EN);
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_SRC_MASK, NAU8821_CLK_SRC_VCO);
+ /* Decrease the VCO frequency and make DSP operate
+ * as default setting for power saving.
+ */
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_MCLK_SRC_MASK, 0xf);
+ regmap_update_bits(regmap, NAU8821_R04_FLL1,
+ NAU8821_ICTRL_LATCH_MASK |
+ NAU8821_FLL_RATIO_MASK, 0x10);
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_SDM_EN, NAU8821_SDM_EN);
+ }
+ break;
+ case NAU8821_CLK_FLL_MCLK:
+ nau8821_sema_acquire(nau8821, HZ);
+ /* Higher FLL reference input frequency can only set lower
+ * gain error, such as 0000 for input reference from MCLK
+ * 12.288Mhz.
+ */
+ regmap_update_bits(regmap, NAU8821_R06_FLL3,
+ NAU8821_FLL_CLK_SRC_MASK | NAU8821_GAIN_ERR_MASK,
+ NAU8821_FLL_CLK_SRC_MCLK | 0);
+ nau8821_sema_release(nau8821);
+ break;
+ case NAU8821_CLK_FLL_BLK:
+ nau8821_sema_acquire(nau8821, HZ);
+ /* If FLL reference input is from low frequency source,
+ * higher error gain can apply such as 0xf which has
+ * the most sensitive gain error correction threshold,
+ * Therefore, FLL has the most accurate DCO to
+ * target frequency.
+ */
+ regmap_update_bits(regmap, NAU8821_R06_FLL3,
+ NAU8821_FLL_CLK_SRC_MASK | NAU8821_GAIN_ERR_MASK,
+ NAU8821_FLL_CLK_SRC_BLK |
+ (0xf << NAU8821_GAIN_ERR_SFT));
+ nau8821_sema_release(nau8821);
+ break;
+ case NAU8821_CLK_FLL_FS:
+ nau8821_sema_acquire(nau8821, HZ);
+ /* If FLL reference input is from low frequency source,
+ * higher error gain can apply such as 0xf which has
+ * the most sensitive gain error correction threshold,
+ * Therefore, FLL has the most accurate DCO to
+ * target frequency.
+ */
+ regmap_update_bits(regmap, NAU8821_R06_FLL3,
+ NAU8821_FLL_CLK_SRC_MASK | NAU8821_GAIN_ERR_MASK,
+ NAU8821_FLL_CLK_SRC_FS |
+ (0xf << NAU8821_GAIN_ERR_SFT));
+ nau8821_sema_release(nau8821);
+ break;
+ default:
+ dev_err(nau8821->dev, "Invalid clock id (%d)\n", clk_id);
+ return -EINVAL;
+ }
+ nau8821->clk_id = clk_id;
+ dev_dbg(nau8821->dev, "Sysclk is %dHz and clock id is %d\n", freq,
+ nau8821->clk_id);
+
+ return 0;
+}
+
+static int nau8821_set_sysclk(struct snd_soc_component *component, int clk_id,
+ int source, unsigned int freq, int dir)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ return nau8821_configure_sysclk(nau8821, clk_id, freq);
+}
+
+static int nau8821_resume_setup(struct nau8821 *nau8821)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ /* Close clock when jack type detection at manual mode */
+ nau8821_configure_sysclk(nau8821, NAU8821_CLK_DIS, 0);
+ if (nau8821->irq) {
+ /* Clear all interruption status */
+ nau8821_int_status_clear_all(regmap);
+
+ /* Enable both insertion and ejection interruptions, and then
+ * bypass de-bounce circuit.
+ */
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_EJECT_EN | NAU8821_IRQ_INSERT_EN, 0);
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_DET_DB_BYPASS,
+ NAU8821_JACK_DET_DB_BYPASS);
+ regmap_update_bits(regmap, NAU8821_R12_INTERRUPT_DIS_CTRL,
+ NAU8821_IRQ_INSERT_DIS | NAU8821_IRQ_EJECT_DIS, 0);
+ }
+
+ return 0;
+}
+
+static int nau8821_set_bias_level(struct snd_soc_component *component,
+ enum snd_soc_bias_level level)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ struct regmap *regmap = nau8821->regmap;
+
+ switch (level) {
+ case SND_SOC_BIAS_ON:
+ break;
+
+ case SND_SOC_BIAS_PREPARE:
+ break;
+
+ case SND_SOC_BIAS_STANDBY:
+ /* Setup codec configuration after resume */
+ if (snd_soc_component_get_bias_level(component) ==
+ SND_SOC_BIAS_OFF)
+ nau8821_resume_setup(nau8821);
+ break;
+
+ case SND_SOC_BIAS_OFF:
+ /* HPL/HPR short to ground */
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_SPKR_DWN1R | NAU8821_SPKR_DWN1L, 0);
+ if (nau8821->irq) {
+ /* Reset semaphore */
+ nau8821_sema_reset(nau8821);
+ /* Reset the configuration of jack type for detection.
+ * Detach 2kOhm Resistors from MICBIAS to MICGND1/2.
+ */
+ regmap_update_bits(regmap, NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_JKR2, 0);
+ /* Turn off all interruptions before system shutdown.
+ * Keep theinterruption quiet before resume
+ * setup completes.
+ */
+ regmap_write(regmap,
+ NAU8821_R12_INTERRUPT_DIS_CTRL, 0xffff);
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_EJECT_EN | NAU8821_IRQ_INSERT_EN,
+ NAU8821_IRQ_EJECT_EN | NAU8821_IRQ_INSERT_EN);
+ }
+ break;
+ }
+
+ return 0;
+}
+
+static int __maybe_unused nau8821_suspend(struct snd_soc_component *component)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ if (nau8821->irq)
+ disable_irq(nau8821->irq);
+ snd_soc_component_force_bias_level(component, SND_SOC_BIAS_OFF);
+ /* Power down codec power; don't suppoet button wakeup */
+ snd_soc_dapm_disable_pin(nau8821->dapm, "MICBIAS");
+ snd_soc_dapm_sync(nau8821->dapm);
+ regcache_cache_only(nau8821->regmap, true);
+ regcache_mark_dirty(nau8821->regmap);
+
+ return 0;
+}
+
+static int __maybe_unused nau8821_resume(struct snd_soc_component *component)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ regcache_cache_only(nau8821->regmap, false);
+ regcache_sync(nau8821->regmap);
+ if (nau8821->irq) {
+ /* Hold semaphore to postpone playback happening
+ * until jack detection done.
+ */
+ nau8821_sema_acquire(nau8821, 0);
+ enable_irq(nau8821->irq);
+ }
+
+ return 0;
+}
+
+static const struct snd_soc_component_driver nau8821_component_driver = {
+ .probe = nau8821_component_probe,
+ .remove = nau8821_component_remove,
+ .set_sysclk = nau8821_set_sysclk,
+ .set_pll = nau8821_set_fll,
+ .set_bias_level = nau8821_set_bias_level,
+ .suspend = nau8821_suspend,
+ .resume = nau8821_resume,
+ .controls = nau8821_controls,
+ .num_controls = ARRAY_SIZE(nau8821_controls),
+ .dapm_widgets = nau8821_dapm_widgets,
+ .num_dapm_widgets = ARRAY_SIZE(nau8821_dapm_widgets),
+ .dapm_routes = nau8821_dapm_routes,
+ .num_dapm_routes = ARRAY_SIZE(nau8821_dapm_routes),
+ .suspend_bias_off = 1,
+ .non_legacy_dai_naming = 1,
+ .idle_bias_on = 1,
+ .use_pmdown_time = 1,
+ .endianness = 1,
+};
+
+/**
+ * nau8821_enable_jack_detect - Specify a jack for event reporting
+ *
+ * @component: component to register the jack with
+ * @jack: jack to use to report headset and button events on
+ *
+ * After this function has been called the headset insert/remove and button
+ * events will be routed to the given jack. Jack can be null to stop
+ * reporting.
+ */
+int nau8821_enable_jack_detect(struct snd_soc_component *component,
+ struct snd_soc_jack *jack)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ int ret;
+
+ nau8821->jack = jack;
+ /* Initiate jack detection work queue */
+ INIT_WORK(&nau8821->jdet_work, nau8821_jdet_work);
+ ret = devm_request_threaded_irq(nau8821->dev, nau8821->irq, NULL,
+ nau8821_interrupt, IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ "nau8821", nau8821);
+ if (ret) {
+ dev_err(nau8821->dev, "Cannot request irq %d (%d)\n",
+ nau8821->irq, ret);
+ return ret;
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(nau8821_enable_jack_detect);
+
+static void nau8821_reset_chip(struct regmap *regmap)
+{
+ regmap_write(regmap, NAU8821_R00_RESET, 0xffff);
+ regmap_write(regmap, NAU8821_R00_RESET, 0xffff);
+}
+
+static void nau8821_print_device_properties(struct nau8821 *nau8821)
+{
+ struct device *dev = nau8821->dev;
+
+ dev_dbg(dev, "jkdet-enable: %d\n", nau8821->jkdet_enable);
+ dev_dbg(dev, "jkdet-pull-enable: %d\n", nau8821->jkdet_pull_enable);
+ dev_dbg(dev, "jkdet-pull-up: %d\n", nau8821->jkdet_pull_up);
+ dev_dbg(dev, "jkdet-polarity: %d\n", nau8821->jkdet_polarity);
+ dev_dbg(dev, "micbias-voltage: %d\n", nau8821->micbias_voltage);
+ dev_dbg(dev, "vref-impedance: %d\n", nau8821->vref_impedance);
+ dev_dbg(dev, "jack-insert-debounce: %d\n",
+ nau8821->jack_insert_debounce);
+ dev_dbg(dev, "jack-eject-debounce: %d\n",
+ nau8821->jack_eject_debounce);
+ dev_dbg(dev, "dmic-clk-threshold: %d\n",
+ nau8821->dmic_clk_threshold);
+}
+
+static int nau8821_read_device_properties(struct device *dev,
+ struct nau8821 *nau8821)
+{
+ int ret;
+
+ nau8821->jkdet_enable = device_property_read_bool(dev,
+ "nuvoton,jkdet-enable");
+ nau8821->jkdet_pull_enable = device_property_read_bool(dev,
+ "nuvoton,jkdet-pull-enable");
+ nau8821->jkdet_pull_up = device_property_read_bool(dev,
+ "nuvoton,jkdet-pull-up");
+ ret = device_property_read_u32(dev, "nuvoton,jkdet-polarity",
+ &nau8821->jkdet_polarity);
+ if (ret)
+ nau8821->jkdet_polarity = 1;
+ ret = device_property_read_u32(dev, "nuvoton,micbias-voltage",
+ &nau8821->micbias_voltage);
+ if (ret)
+ nau8821->micbias_voltage = 6;
+ ret = device_property_read_u32(dev, "nuvoton,vref-impedance",
+ &nau8821->vref_impedance);
+ if (ret)
+ nau8821->vref_impedance = 2;
+ ret = device_property_read_u32(dev, "nuvoton,jack-insert-debounce",
+ &nau8821->jack_insert_debounce);
+ if (ret)
+ nau8821->jack_insert_debounce = 7;
+ ret = device_property_read_u32(dev, "nuvoton,jack-eject-debounce",
+ &nau8821->jack_eject_debounce);
+ if (ret)
+ nau8821->jack_eject_debounce = 0;
+ ret = device_property_read_u32(dev, "nuvoton,dmic-clk-threshold",
+ &nau8821->dmic_clk_threshold);
+ if (ret)
+ nau8821->dmic_clk_threshold = 3072000;
+
+ return 0;
+}
+
+static void nau8821_init_regs(struct nau8821 *nau8821)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ /* Enable Bias/Vmid */
+ regmap_update_bits(regmap, NAU8821_R66_BIAS_ADJ,
+ NAU8821_BIAS_VMID, NAU8821_BIAS_VMID);
+ regmap_update_bits(regmap, NAU8821_R76_BOOST,
+ NAU8821_GLOBAL_BIAS_EN, NAU8821_GLOBAL_BIAS_EN);
+ /* VMID Tieoff setting and enable TESTDAC.
+ * This sets the analog DAC inputs to a '0' input signal to avoid
+ * any glitches due to power up transients in both the analog and
+ * digital DAC circuit.
+ */
+ regmap_update_bits(regmap, NAU8821_R66_BIAS_ADJ,
+ NAU8821_BIAS_VMID_SEL_MASK | NAU8821_BIAS_TESTDAC_EN,
+ (nau8821->vref_impedance << NAU8821_BIAS_VMID_SEL_SFT) |
+ NAU8821_BIAS_TESTDAC_EN);
+ /* Disable short Frame Sync detection logic */
+ regmap_update_bits(regmap, NAU8821_R1E_LEFT_TIME_SLOT,
+ NAU8821_DIS_FS_SHORT_DET, NAU8821_DIS_FS_SHORT_DET);
+ /* Disable Boost Driver, Automatic Short circuit protection enable */
+ regmap_update_bits(regmap, NAU8821_R76_BOOST,
+ NAU8821_PRECHARGE_DIS | NAU8821_HP_BOOST_DIS |
+ NAU8821_HP_BOOST_G_DIS | NAU8821_SHORT_SHUTDOWN_EN,
+ NAU8821_PRECHARGE_DIS | NAU8821_HP_BOOST_DIS |
+ NAU8821_HP_BOOST_G_DIS | NAU8821_SHORT_SHUTDOWN_EN);
+ /* Class G timer 64ms */
+ regmap_update_bits(regmap, NAU8821_R4B_CLASSG_CTRL,
+ NAU8821_CLASSG_TIMER_MASK,
+ 0x20 << NAU8821_CLASSG_TIMER_SFT);
+ /* Class AB bias current to 2x, DAC Capacitor enable MSB/LSB */
+ regmap_update_bits(regmap, NAU8821_R6A_ANALOG_CONTROL_2,
+ NAU8821_HP_NON_CLASSG_CURRENT_2xADJ |
+ NAU8821_DAC_CAPACITOR_MSB | NAU8821_DAC_CAPACITOR_LSB,
+ NAU8821_HP_NON_CLASSG_CURRENT_2xADJ |
+ NAU8821_DAC_CAPACITOR_MSB | NAU8821_DAC_CAPACITOR_LSB);
+ /* Disable DACR/L power */
+ regmap_update_bits(regmap, NAU8821_R80_CHARGE_PUMP,
+ NAU8821_POWER_DOWN_DACR | NAU8821_POWER_DOWN_DACL, 0);
+ /* DAC clock delay 2ns, VREF */
+ regmap_update_bits(regmap, NAU8821_R73_RDAC,
+ NAU8821_DAC_CLK_DELAY_MASK | NAU8821_DAC_VREF_MASK,
+ (0x2 << NAU8821_DAC_CLK_DELAY_SFT) |
+ (0x3 << NAU8821_DAC_VREF_SFT));
+
+ regmap_update_bits(regmap, NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_VOLTAGE_MASK, nau8821->micbias_voltage);
+ /* Default oversampling/decimations settings are unusable
+ * (audible hiss). Set it to something better.
+ */
+ regmap_update_bits(regmap, NAU8821_R2B_ADC_RATE,
+ NAU8821_ADC_SYNC_DOWN_MASK, NAU8821_ADC_SYNC_DOWN_64);
+ regmap_update_bits(regmap, NAU8821_R2C_DAC_CTRL1,
+ NAU8821_DAC_OVERSAMPLE_MASK, NAU8821_DAC_OVERSAMPLE_64);
+}
+
+static int nau8821_setup_irq(struct nau8821 *nau8821)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ sema_init(&nau8821->jd_sem, 1);
+
+ /* Jack detection */
+ regmap_update_bits(regmap, NAU8821_R1A_GPIO12_CTRL,
+ NAU8821_JKDET_OUTPUT_EN,
+ nau8821->jkdet_enable ? 0 : NAU8821_JKDET_OUTPUT_EN);
+ regmap_update_bits(regmap, NAU8821_R1A_GPIO12_CTRL,
+ NAU8821_JKDET_PULL_EN,
+ nau8821->jkdet_pull_enable ? 0 : NAU8821_JKDET_PULL_EN);
+ regmap_update_bits(regmap, NAU8821_R1A_GPIO12_CTRL,
+ NAU8821_JKDET_PULL_UP,
+ nau8821->jkdet_pull_up ? NAU8821_JKDET_PULL_UP : 0);
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_POLARITY,
+ /* jkdet_polarity - 1 is for active-low */
+ nau8821->jkdet_polarity ? 0 : NAU8821_JACK_POLARITY);
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_INSERT_DEBOUNCE_MASK,
+ nau8821->jack_insert_debounce <<
+ NAU8821_JACK_INSERT_DEBOUNCE_SFT);
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_EJECT_DEBOUNCE_MASK,
+ nau8821->jack_eject_debounce <<
+ NAU8821_JACK_EJECT_DEBOUNCE_SFT);
+ /* Pull up IRQ pin */
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_PIN_PULL_UP | NAU8821_IRQ_PIN_PULL_EN |
+ NAU8821_IRQ_OUTPUT_EN, NAU8821_IRQ_PIN_PULL_UP |
+ NAU8821_IRQ_PIN_PULL_EN | NAU8821_IRQ_OUTPUT_EN);
+ /* Disable interruption before codec initiation done */
+ /* Mask unneeded IRQs: 1 - disable, 0 - enable */
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK, 0x3f5, 0x3f5);
+
+ return 0;
+}
+
+static int nau8821_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &i2c->dev;
+ struct nau8821 *nau8821 = dev_get_platdata(&i2c->dev);
+ int ret, value;
+
+ if (!nau8821) {
+ nau8821 = devm_kzalloc(dev, sizeof(*nau8821), GFP_KERNEL);
+ if (!nau8821)
+ return -ENOMEM;
+ nau8821_read_device_properties(dev, nau8821);
+ }
+ i2c_set_clientdata(i2c, nau8821);
+
+ nau8821->regmap = devm_regmap_init_i2c(i2c, &nau8821_regmap_config);
+ if (IS_ERR(nau8821->regmap))
+ return PTR_ERR(nau8821->regmap);
+
+ nau8821->dev = dev;
+ nau8821->irq = i2c->irq;
+ nau8821_print_device_properties(nau8821);
+
+ nau8821_reset_chip(nau8821->regmap);
+ ret = regmap_read(nau8821->regmap, NAU8821_R58_I2C_DEVICE_ID, &value);
+ if (ret) {
+ dev_err(dev, "Failed to read device id (%d)\n", ret);
+ return ret;
+ }
+ nau8821_init_regs(nau8821);
+
+ if (i2c->irq)
+ nau8821_setup_irq(nau8821);
+
+ ret = devm_snd_soc_register_component(&i2c->dev,
+ &nau8821_component_driver, &nau8821_dai, 1);
+
+ return ret;
+}
+
+static const struct i2c_device_id nau8821_i2c_ids[] = {
+ { "nau8821", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, nau8821_i2c_ids);
+
+#ifdef CONFIG_OF
+static const struct of_device_id nau8821_of_ids[] = {
+ { .compatible = "nuvoton,nau8821", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, nau8821_of_ids);
+#endif
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id nau8821_acpi_match[] = {
+ { "NVTN2020", 0 },
+ {},
+};
+MODULE_DEVICE_TABLE(acpi, nau8821_acpi_match);
+#endif
+
+static struct i2c_driver nau8821_driver = {
+ .driver = {
+ .name = "nau8821",
+ .of_match_table = of_match_ptr(nau8821_of_ids),
+ .acpi_match_table = ACPI_PTR(nau8821_acpi_match),
+ },
+ .probe = nau8821_i2c_probe,
+ .id_table = nau8821_i2c_ids,
+};
+module_i2c_driver(nau8821_driver);
+
+MODULE_DESCRIPTION("ASoC nau8821 driver");
+MODULE_AUTHOR("John Hsu <kchsu0@nuvoton.com>");
+MODULE_AUTHOR("Seven Lee <wtli@nuvoton.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/sound/soc/codecs/nau8821.h b/sound/soc/codecs/nau8821.h
new file mode 100644
index 000000000000..3541decc34f0
--- /dev/null
+++ b/sound/soc/codecs/nau8821.h
@@ -0,0 +1,533 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * NAU88L21 ALSA SoC audio driver
+ *
+ * Copyright 2021 Nuvoton Technology Corp.
+ * Author: John Hsu <kchsu0@nuvoton.com>
+ * Co-author: Seven Lee <wtli@nuvoton.com>
+ */
+
+#ifndef __NAU8821_H__
+#define __NAU8821_H__
+
+#define NAU8821_R00_RESET 0x00
+#define NAU8821_R01_ENA_CTRL 0x01
+#define NAU8821_R03_CLK_DIVIDER 0x03
+#define NAU8821_R04_FLL1 0x04
+#define NAU8821_R05_FLL2 0x05
+#define NAU8821_R06_FLL3 0x06
+#define NAU8821_R07_FLL4 0x07
+#define NAU8821_R08_FLL5 0x08
+#define NAU8821_R09_FLL6 0x09
+#define NAU8821_R0A_FLL7 0x0a
+#define NAU8821_R0B_FLL8 0x0b
+#define NAU8821_R0D_JACK_DET_CTRL 0x0d
+#define NAU8821_R0F_INTERRUPT_MASK 0x0f
+#define NAU8821_R10_IRQ_STATUS 0x10
+#define NAU8821_R11_INT_CLR_KEY_STATUS 0x11
+#define NAU8821_R12_INTERRUPT_DIS_CTRL 0x12
+#define NAU8821_R13_DMIC_CTRL 0x13
+#define NAU8821_R1A_GPIO12_CTRL 0x1a
+#define NAU8821_R1B_TDM_CTRL 0x1b
+#define NAU8821_R1C_I2S_PCM_CTRL1 0x1c
+#define NAU8821_R1D_I2S_PCM_CTRL2 0x1d
+#define NAU8821_R1E_LEFT_TIME_SLOT 0x1e
+#define NAU8821_R1F_RIGHT_TIME_SLOT 0x1f
+#define NAU8821_R21_BIQ0_COF1 0x21
+#define NAU8821_R22_BIQ0_COF2 0x22
+#define NAU8821_R23_BIQ0_COF3 0x23
+#define NAU8821_R24_BIQ0_COF4 0x24
+#define NAU8821_R25_BIQ0_COF5 0x25
+#define NAU8821_R26_BIQ0_COF6 0x26
+#define NAU8821_R27_BIQ0_COF7 0x27
+#define NAU8821_R28_BIQ0_COF8 0x28
+#define NAU8821_R29_BIQ0_COF9 0x29
+#define NAU8821_R2A_BIQ0_COF10 0x2a
+#define NAU8821_R2B_ADC_RATE 0x2b
+#define NAU8821_R2C_DAC_CTRL1 0x2c
+#define NAU8821_R2D_DAC_CTRL2 0x2d
+#define NAU8821_R2F_DAC_DGAIN_CTRL 0x2f
+#define NAU8821_R30_ADC_DGAIN_CTRL 0x30
+#define NAU8821_R31_MUTE_CTRL 0x31
+#define NAU8821_R32_HSVOL_CTRL 0x32
+#define NAU8821_R34_DACR_CTRL 0x34
+#define NAU8821_R35_ADC_DGAIN_CTRL1 0x35
+#define NAU8821_R36_ADC_DRC_KNEE_IP12 0x36
+#define NAU8821_R37_ADC_DRC_KNEE_IP34 0x37
+#define NAU8821_R38_ADC_DRC_SLOPES 0x38
+#define NAU8821_R39_ADC_DRC_ATKDCY 0x39
+#define NAU8821_R3A_DAC_DRC_KNEE_IP12 0x3a
+#define NAU8821_R3B_DAC_DRC_KNEE_IP34 0x3b
+#define NAU8821_R3C_DAC_DRC_SLOPES 0x3c
+#define NAU8821_R3D_DAC_DRC_ATKDCY 0x3d
+#define NAU8821_R41_BIQ1_COF1 0x41
+#define NAU8821_R42_BIQ1_COF2 0x42
+#define NAU8821_R43_BIQ1_COF3 0x43
+#define NAU8821_R44_BIQ1_COF4 0x44
+#define NAU8821_R45_BIQ1_COF5 0x45
+#define NAU8821_R46_BIQ1_COF6 0x46
+#define NAU8821_R47_BIQ1_COF7 0x47
+#define NAU8821_R48_BIQ1_COF8 0x48
+#define NAU8821_R49_BIQ1_COF9 0x49
+#define NAU8821_R4A_BIQ1_COF10 0x4a
+#define NAU8821_R4B_CLASSG_CTRL 0x4b
+#define NAU8821_R4C_IMM_MODE_CTRL 0x4c
+#define NAU8821_R4D_IMM_RMS_L 0x4d
+#define NAU8821_R4E_FUSE_CTRL2 0x4e
+#define NAU8821_R4F_FUSE_CTRL3 0x4f
+#define NAU8821_R51_FUSE_CTRL1 0x51
+#define NAU8821_R53_OTPDOUT_1 0x53
+#define NAU8821_R54_OTPDOUT_2 0x54
+#define NAU8821_R55_MISC_CTRL 0x55
+#define NAU8821_R58_I2C_DEVICE_ID 0x58
+#define NAU8821_R59_SARDOUT_RAM_STATUS 0x59
+#define NAU8821_R5A_SOFTWARE_RST 0x5a
+#define NAU8821_R66_BIAS_ADJ 0x66
+#define NAU8821_R68_TRIM_SETTINGS 0x68
+#define NAU8821_R69_ANALOG_CONTROL_1 0x69
+#define NAU8821_R6A_ANALOG_CONTROL_2 0x6a
+#define NAU8821_R6B_PGA_MUTE 0x6b
+#define NAU8821_R71_ANALOG_ADC_1 0x71
+#define NAU8821_R72_ANALOG_ADC_2 0x72
+#define NAU8821_R73_RDAC 0x73
+#define NAU8821_R74_MIC_BIAS 0x74
+#define NAU8821_R76_BOOST 0x76
+#define NAU8821_R77_FEPGA 0x77
+#define NAU8821_R7E_PGA_GAIN 0x7e
+#define NAU8821_R7F_POWER_UP_CONTROL 0x7f
+#define NAU8821_R80_CHARGE_PUMP 0x80
+#define NAU8821_R81_CHARGE_PUMP_INPUT_READ 0x81
+#define NAU8821_R82_GENERAL_STATUS 0x82
+#define NAU8821_REG_MAX NAU8821_R82_GENERAL_STATUS
+/* 16-bit control register address, and 16-bits control register data */
+#define NAU8821_REG_ADDR_LEN 16
+#define NAU8821_REG_DATA_LEN 16
+
+/* ENA_CTRL (0x01) */
+#define NAU8821_CLK_DAC_INV_SFT 14
+#define NAU8821_CLK_DAC_INV (0x1 << NAU8821_CLK_DAC_INV)
+#define NAU8821_EN_DACR_SFT 11
+#define NAU8821_EN_DACR (0x1 << NAU8821_EN_DACR_SFT)
+#define NAU8821_EN_DACL_SFT 10
+#define NAU8821_EN_DACL (0x1 << NAU8821_EN_DACL_SFT)
+#define NAU8821_EN_ADCR_SFT 9
+#define NAU8821_EN_ADCR (0x1 << NAU8821_EN_ADCR_SFT)
+#define NAU8821_EN_ADCL_SFT 8
+#define NAU8821_EN_ADCL (0x1 << NAU8821_EN_ADCL_SFT)
+#define NAU8821_EN_ADC_CLK_SFT 7
+#define NAU8821_EN_ADC_CLK (0x1 << NAU8821_EN_ADC_CLK_SFT)
+#define NAU8821_EN_DAC_CLK_SFT 6
+#define NAU8821_EN_DAC_CLK (0x1 << NAU8821_EN_DAC_CLK_SFT)
+#define NAU8821_EN_I2S_CLK_SFT 4
+#define NAU8821_EN_I2S_CLK (0x1 << NAU8821_EN_I2S_CLK_SFT)
+#define NAU8821_EN_DRC_CLK_SFT 0
+#define NAU8821_EN_DRC_CLK (0x1 << NAU8821_EN_DRC_CLK_SFT)
+
+/* CLK_DIVIDER (0x03) */
+#define NAU8821_CLK_SRC_SFT 15
+#define NAU8821_CLK_SRC_MASK (0x1 << NAU8821_CLK_SRC_SFT)
+#define NAU8821_CLK_SRC_VCO (0x1 << NAU8821_CLK_SRC_SFT)
+#define NAU8821_CLK_SRC_MCLK (0x0 << NAU8821_CLK_SRC_SFT)
+#define NAU8821_CLK_CODEC_SRC_SFT 13
+#define NAU8821_CLK_CODEC_SRC_MASK (0x1 << NAU8821_CLK_CODEC_SRC_SFT)
+#define NAU8821_CLK_CODEC_SRC_VCO (0x1 << NAU8821_CLK_CODEC_SRC_SFT)
+#define NAU8821_CLK_CODEC_SRC_MCLK (0x0 << NAU8821_CLK_CODEC_SRC_SFT)
+#define NAU8821_CLK_ADC_SRC_SFT 6
+#define NAU8821_CLK_ADC_SRC_MASK (0x3 << NAU8821_CLK_ADC_SRC_SFT)
+#define NAU8821_CLK_DAC_SRC_SFT 4
+#define NAU8821_CLK_DAC_SRC_MASK (0x3 << NAU8821_CLK_DAC_SRC_SFT)
+#define NAU8821_CLK_MCLK_SRC_MASK 0xf
+
+/* FLL1 (0x04) */
+#define NAU8821_ICTRL_LATCH_SFT 10
+#define NAU8821_ICTRL_LATCH_MASK (0x7 << NAU8821_ICTRL_LATCH_SFT)
+#define NAU8821_FLL_RATIO_MASK 0x7f
+
+/* FLL3 (0x06) */
+#define NAU8821_GAIN_ERR_SFT 12
+#define NAU8821_GAIN_ERR_MASK (0xf << NAU8821_GAIN_ERR_SFT)
+#define NAU8821_FLL_CLK_SRC_SFT 10
+#define NAU8821_FLL_CLK_SRC_MASK (0x3 << NAU8821_FLL_CLK_SRC_SFT)
+#define NAU8821_FLL_CLK_SRC_FS (0x3 << NAU8821_FLL_CLK_SRC_SFT)
+#define NAU8821_FLL_CLK_SRC_BLK (0x2 << NAU8821_FLL_CLK_SRC_SFT)
+#define NAU8821_FLL_CLK_SRC_MCLK (0x0 << NAU8821_FLL_CLK_SRC_SFT)
+#define NAU8821_FLL_INTEGER_MASK 0x3ff
+
+/* FLL4 (0x07) */
+#define NAU8821_HIGHBW_EN_SFT 15
+#define NAU8821_HIGHBW_EN (0x1 << NAU8821_HIGHBW_EN_SFT)
+#define NAU8821_FLL_REF_DIV_SFT 10
+#define NAU8821_FLL_REF_DIV_MASK (0x3 << NAU8821_FLL_REF_DIV_SFT)
+
+/* FLL5 (0x08) */
+#define NAU8821_FLL_PDB_DAC_EN (0x1 << 15)
+#define NAU8821_FLL_LOOP_FTR_EN (0x1 << 14)
+#define NAU8821_FLL_CLK_SW_SFT 13
+#define NAU8821_FLL_CLK_SW_MASK (0x1 << NAU8821_FLL_CLK_SW_SFT)
+#define NAU8821_FLL_CLK_SW_N2 (0x1 << NAU8821_FLL_CLK_SW_SFT)
+#define NAU8821_FLL_CLK_SW_REF (0x0 << NAU8821_FLL_CLK_SW_SFT)
+#define NAU8821_FLL_FTR_SW_SFT 12
+#define NAU8821_FLL_FTR_SW_MASK (0x1 << NAU8821_FLL_FTR_SW_SFT)
+#define NAU8821_FLL_FTR_SW_ACCU (0x1 << NAU8821_FLL_FTR_SW_SFT)
+#define NAU8821_FLL_FTR_SW_FILTER (0x0 << NAU8821_FLL_FTR_SW_SFT)
+
+/* FLL6 (0x09) */
+#define NAU8821_DCO_EN (0x1 << 15)
+#define NAU8821_SDM_EN (0x1 << 14)
+#define NAU8821_CUTOFF500 (0x1 << 13)
+
+/* FLL7 (0x0a) */
+#define NAU8821_FLL_FRACH_MASK 0xff
+
+/* FLL8 (0x0b) */
+#define NAU8821_FLL_FRACL_MASK 0xffff
+
+/* JACK_DET_CTRL (0x0d) */
+/* 0 - open, 1 - short to GND */
+#define NAU8821_SPKR_DWN1R_SFT 15
+#define NAU8821_SPKR_DWN1R (0x1 << NAU8821_SPKR_DWN1R_SFT)
+#define NAU8821_SPKR_DWN1L_SFT 14
+#define NAU8821_SPKR_DWN1L (0x1 << NAU8821_SPKR_DWN1L_SFT)
+#define NAU8821_JACK_DET_RESTART (0x1 << 9)
+#define NAU8821_JACK_DET_DB_BYPASS (0x1 << 8)
+#define NAU8821_JACK_INSERT_DEBOUNCE_SFT 5
+#define NAU8821_JACK_INSERT_DEBOUNCE_MASK (0x7 << NAU8821_JACK_INSERT_DEBOUNCE_SFT)
+#define NAU8821_JACK_EJECT_DEBOUNCE_SFT 2
+#define NAU8821_JACK_EJECT_DEBOUNCE_MASK (0x7 << NAU8821_JACK_EJECT_DEBOUNCE_SFT)
+#define NAU8821_JACK_POLARITY (0x1 << 1) /* 0 - active low, 1 - active high */
+
+/* INTERRUPT_MASK (0x0f) */
+#define NAU8821_IRQ_PIN_PULL_UP (0x1 << 14)
+#define NAU8821_IRQ_PIN_PULL_EN (0x1 << 13)
+#define NAU8821_IRQ_OUTPUT_EN (0x1 << 11)
+#define NAU8821_IRQ_RMS_EN (0x1 << 8)
+#define NAU8821_IRQ_KEY_RELEASE_EN (0x1 << 7)
+#define NAU8821_IRQ_KEY_PRESS_EN (0x1 << 6)
+#define NAU8821_IRQ_MIC_DET_EN (0x1 << 4)
+#define NAU8821_IRQ_EJECT_EN (0x1 << 2)
+#define NAU8821_IRQ_INSERT_EN 0x1
+
+/* IRQ_STATUS (0x10) */
+#define NAU8821_SHORT_CIRCUIT_IRQ (0x1 << 9)
+#define NAU8821_IMPEDANCE_MEAS_IRQ (0x1 << 8)
+#define NAU8821_KEY_IRQ_SFT 6
+#define NAU8821_KEY_IRQ_MASK (0x3 << NAU8821_KEY_IRQ_SFT)
+#define NAU8821_KEY_RELEASE_IRQ (0x2 << NAU8821_KEY_IRQ_SFT)
+#define NAU8821_KEY_SHORT_PRESS_IRQ (0x1 << NAU8821_KEY_IRQ_SFT)
+#define NAU8821_MIC_DETECT_IRQ (0x1 << 4)
+#define NAU8821_JACK_EJECT_IRQ_MASK (0x3 << 2)
+#define NAU8821_JACK_EJECT_DETECTED (0x1 << 2)
+#define NAU8821_JACK_INSERT_IRQ_MASK 0x3
+#define NAU8821_JACK_INSERT_DETECTED 0x1
+
+/* INTERRUPT_DIS_CTRL (0x12) */
+#define NAU8821_IRQ_KEY_RELEASE_DIS (0x1 << 7)
+#define NAU8821_IRQ_KEY_PRESS_DIS (0x1 << 6)
+#define NAU8821_IRQ_MIC_DIS (0x1 << 4)
+#define NAU8821_IRQ_EJECT_DIS (0x1 << 2)
+#define NAU8821_IRQ_INSERT_DIS 0x1
+
+/* DMIC_CTRL (0x13) */
+#define NAU8821_DMIC_DS_SFT 7
+#define NAU8821_DMIC_DS_MASK (0x1 << NAU8821_DMIC_DS_SFT)
+#define NAU8821_DMIC_DS_HIGH (0x1 << NAU8821_DMIC_DS_SFT)
+#define NAU8821_DMIC_DS_LOW (0x0 << NAU8821_DMIC_DS_SFT)
+#define NAU8821_DMIC_SRC_SFT 1
+#define NAU8821_DMIC_SRC_MASK (0x3 << NAU8821_DMIC_SRC_SFT)
+#define NAU8821_CLK_DMIC_SRC (0x2 << NAU8821_DMIC_SRC_SFT)
+#define NAU8821_DMIC_EN_SFT 0
+
+/* GPIO12_CTRL (0x1a) */
+#define NAU8821_JKDET_PULL_UP (0x1 << 11) /* 0 - pull down, 1 - pull up */
+#define NAU8821_JKDET_PULL_EN (0x1 << 9) /* 0 - enable pull, 1 - disable */
+#define NAU8821_JKDET_OUTPUT_EN (0x1 << 8) /* 0 - enable input, 1 - enable output */
+
+/* TDM_CTRL (0x1b) */
+#define NAU8821_TDM_EN_SFT 15
+#define NAU8821_TDM_EN (0x1 << NAU8821_TDM_EN_SFT)
+#define NAU8821_DACL_CH_SFT 7
+#define NAU8821_DACL_CH_MASK (0x7 << NAU8821_DACL_CH_SFT)
+#define NAU8821_DACR_CH_SFT 4
+#define NAU8821_DACR_CH_MASK (0x7 << NAU8821_DACR_CH_SFT)
+#define NAU8821_ADCL_CH_SFT 2
+#define NAU8821_ADCL_CH_MASK (0x3 << NAU8821_ADCL_CH_SFT)
+#define NAU8821_ADCR_CH_SFT 0
+#define NAU8821_ADCR_CH_MASK 0x3
+
+/* I2S_PCM_CTRL1 (0x1c) */
+#define NAU8821_I2S_BP_SFT 7
+#define NAU8821_I2S_BP_MASK (0x1 << NAU8821_I2S_BP_SFT)
+#define NAU8821_I2S_BP_INV (0x1 << NAU8821_I2S_BP_SFT)
+#define NAU8821_I2S_PCMB_SFT 6
+#define NAU8821_I2S_PCMB_MASK (0x1 << NAU8821_I2S_PCMB_SFT)
+#define NAU8821_I2S_PCMB_EN (0x1 << NAU8821_I2S_PCMB_SFT)
+#define NAU8821_I2S_DL_SFT 2
+#define NAU8821_I2S_DL_MASK (0x3 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DL_32 (0x3 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DL_24 (0x2 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DL_20 (0x1 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DL_16 (0x0 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DF_MASK 0x3
+#define NAU8821_I2S_DF_PCM_AB 0x3
+#define NAU8821_I2S_DF_I2S 0x2
+#define NAU8821_I2S_DF_LEFT 0x1
+#define NAU8821_I2S_DF_RIGTH 0x0
+
+/* I2S_PCM_CTRL2 (0x1d) */
+#define NAU8821_I2S_TRISTATE_SFT 15
+#define NAU8821_I2S_TRISTATE (0x1 << NAU8821_I2S_TRISTATE_SFT)
+#define NAU8821_I2S_LRC_DIV_SFT 12
+#define NAU8821_I2S_LRC_DIV_MASK (0x3 << NAU8821_I2S_LRC_DIV_SFT)
+#define NAU8821_I2S_MS_SFT 3
+#define NAU8821_I2S_MS_MASK (0x1 << NAU8821_I2S_MS_SFT)
+#define NAU8821_I2S_MS_MASTER (0x1 << NAU8821_I2S_MS_SFT)
+#define NAU8821_I2S_MS_SLAVE (0x0 << NAU8821_I2S_MS_SFT)
+#define NAU8821_I2S_BLK_DIV_MASK 0x7
+
+/* LEFT_TIME_SLOT (0x1e) */
+#define NAU8821_TSLOT_L_OFFSET_MASK 0x3ff
+#define NAU8821_DIS_FS_SHORT_DET (0x1 << 13)
+
+/* RIGHT_TIME_SLOT (0x1f) */
+#define NAU8821_TSLOT_R_OFFSET_MASK 0x3ff
+
+/* BIQ0_COF10 (0x2a) */
+#define NAU8821_BIQ0_ADC_EN_SFT 3
+#define NAU8821_BIQ0_ADC_EN_EN (0x1 << NAU8821_BIQ0_ADC_EN_SFT)
+
+/* ADC_RATE (0x2b) */
+#define NAU8821_ADC_SYNC_DOWN_SFT 0
+#define NAU8821_ADC_SYNC_DOWN_MASK 0x3
+#define NAU8821_ADC_SYNC_DOWN_256 0x3
+#define NAU8821_ADC_SYNC_DOWN_128 0x2
+#define NAU8821_ADC_SYNC_DOWN_64 0x1
+#define NAU8821_ADC_SYNC_DOWN_32 0x0
+#define NAU8821_ADC_L_SRC_SFT 15
+#define NAU8821_ADC_L_SRC_EN (0x1 << NAU8821_ADC_L_SRC_SFT)
+#define NAU8821_ADC_R_SRC_SFT 14
+#define NAU8821_ADC_R_SRC_EN (0x1 << NAU8821_ADC_R_SRC_SFT)
+
+/* DAC_CTRL1 (0x2c) */
+#define NAU8821_DAC_OVERSAMPLE_SFT 0
+#define NAU8821_DAC_OVERSAMPLE_MASK 0x7
+#define NAU8821_DAC_OVERSAMPLE_32 0x4
+#define NAU8821_DAC_OVERSAMPLE_128 0x2
+#define NAU8821_DAC_OVERSAMPLE_256 0x1
+#define NAU8821_DAC_OVERSAMPLE_64 0x0
+
+/* DAC_DGAIN_CTRL (0x2f) */
+#define NAU8821_DAC1_TO_DAC0_ST_SFT 8
+#define NAU8821_DAC1_TO_DAC0_ST_MASK (0xff << NAU8821_DAC1_TO_DAC0_ST_SFT)
+#define NAU8821_DAC0_TO_DAC1_ST_SFT 0
+#define NAU8821_DAC0_TO_DAC1_ST_MASK 0xff
+
+/* MUTE_CTRL (0x31) */
+#define NAU8821_DAC_ZC_EN (0x1 << 12)
+#define NAU8821_DAC_SOFT_MUTE (0x1 << 9)
+#define NAU8821_ADC_ZC_EN (0x1 << 2)
+#define NAU8821_ADC_SOFT_MUTE (0x1 << 1)
+
+/* HSVOL_CTRL (0x32) */
+#define NAU8821_HP_MUTE (0x1 << 15)
+#define NAU8821_HP_MUTE_AUTO (0x1 << 14)
+#define NAU8821_HPL_MUTE (0x1 << 13)
+#define NAU8821_HPR_MUTE (0x1 << 12)
+#define NAU8821_HPL_VOL_SFT 4
+#define NAU8821_HPL_VOL_MASK (0x3 << NAU8821_HPL_VOL_SFT)
+#define NAU8821_HPR_VOL_SFT 0
+#define NAU8821_HPR_VOL_MASK (0x3 << NAU8821_HPR_VOL_SFT)
+
+/* DACR_CTRL (0x34) */
+#define NAU8821_DACR_CH_VOL_SFT 8
+#define NAU8821_DACR_CH_VOL_MASK (0xff << NAU8821_DACR_CH_VOL_SFT)
+#define NAU8821_DACL_CH_VOL_SFT 0
+#define NAU8821_DACL_CH_VOL_MASK 0xff
+
+/* ADC_DGAIN_CTRL1 (0x35) */
+#define NAU8821_ADCR_CH_VOL_SFT 8
+#define NAU8821_ADCR_CH_VOL_MASK (0xff << NAU8821_ADCR_CH_VOL_SFT)
+#define NAU8821_ADCL_CH_VOL_SFT 0
+#define NAU8821_ADCL_CH_VOL_MASK 0xff
+
+/* BIQ1_COF10 (0x4a) */
+#define NAU8821_BIQ1_DAC_EN_SFT 3
+#define NAU8821_BIQ1_DAC_EN_EN (0x1 << NAU8821_BIQ1_DAC_EN_SFT)
+
+/* CLASSG_CTRL (0x4b) */
+#define NAU8821_CLASSG_TIMER_SFT 8
+#define NAU8821_CLASSG_TIMER_MASK (0x3f << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_64MS (0x20 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_32MS (0x10 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_16MS (0x8 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_8MS (0x4 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_2MS (0x2 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_1MS (0x1 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_RDAC_EN_SFT 2
+#define NAU8821_CLASSG_RDAC_EN (0x1 << NAU8821_CLASSG_RDAC_EN_SFT)
+#define NAU8821_CLASSG_LDAC_EN_SFT 1
+#define NAU8821_CLASSG_LDAC_EN (0x1 << NAU8821_CLASSG_LDAC_EN_SFT)
+#define NAU8821_CLASSG_EN_SFT 0
+#define NAU8821_CLASSG_EN 0x1
+
+/* IMM_MODE_CTRL (0x4C) */
+#define NAU8821_IMM_THD_SFT 8
+#define NAU8821_IMM_THD_MASK (0x3f << NAU8821_IMM_THD_SFT)
+#define NAU8821_IMM_GEN_VOL_SFT 6
+#define NAU8821_IMM_GEN_VOL_MASK (0x3 << NAU8821_IMM_GEN_VOL_SFT)
+#define NAU8821_IMM_CYC_SFT 4
+#define NAU8821_IMM_CYC_MASK (0x3 << NAU8821_IMM_CYC_SFT)
+#define NAU8821_IMM_EN (0x1 << 3)
+#define NAU8821_IMM_DAC_SRC_MASK 0x3
+
+/* I2C_DEVICE_ID (0x58) */
+#define NAU8821_KEYDET (0x1 << 7)
+#define NAU8821_MICDET (0x1 << 6)
+#define NAU8821_SOFTWARE_ID_MASK 0x3
+
+/* BIAS_ADJ (0x66) */
+#define NAU8821_BIAS_HP_IMP (0x1 << 15)
+#define NAU8821_BIAS_TESTDAC_SFT 8
+#define NAU8821_BIAS_TESTDAC_EN (0x3 << NAU8821_BIAS_TESTDAC_SFT)
+#define NAU8821_BIAS_TESTDACR_EN (0x2 << NAU8821_BIAS_TESTDAC_SFT)
+#define NAU8821_BIAS_TESTDACL_EN (0x1 << NAU8821_BIAS_TESTDAC_SFT)
+#define NAU8821_BIAS_VMID (0x1 << 6)
+#define NAU8821_BIAS_VMID_SEL_SFT 4
+#define NAU8821_BIAS_VMID_SEL_MASK (0x3 << NAU8821_BIAS_VMID_SEL_SFT)
+
+/* ANALOG_CONTROL_1 (0x69) */
+#define NAU8821_JD_POL_SFT 2
+#define NAU8821_JD_POL_MASK (0x1 << NAU8821_JD_POL_SFT)
+#define NAU8821_JD_POL_INV (0x1 << NAU8821_JD_POL_SFT)
+#define NAU8821_JD_OUT_POL_SFT 1
+#define NAU8821_JD_OUT_POL_MASK (0x1 << NAU8821_JD_OUT_POL_SFT)
+#define NAU8821_JD_OUT_POL_INV (0x1 << NAU8821_JD_OUT_POL_SFT)
+#define NAU8821_JD_EN_SFT 0
+#define NAU8821_JD_EN 0x1
+
+/* ANALOG_CONTROL_2 (0x6a) */
+#define NAU8821_HP_NON_CLASSG_CURRENT_2xADJ (0x1 << 12)
+#define NAU8821_DAC_CAPACITOR_MSB (0x1 << 1)
+#define NAU8821_DAC_CAPACITOR_LSB 0x1
+
+/* ANALOG_ADC_1 (0x71) */
+#define NAU8821_MICDET_EN_SFT 0
+#define NAU8821_MICDET_MASK 0x1
+#define NAU8821_MICDET_DIS 0x1
+#define NAU8821_MICDET_EN 0x0
+
+/* ANALOG_ADC_2 (0x72) */
+#define NAU8821_ADC_VREFSEL_SFT 8
+#define NAU8821_ADC_VREFSEL_MASK (0x3 << NAU8821_ADC_VREFSEL_SFT)
+#define NAU8821_POWERUP_ADCL_SFT 6
+#define NAU8821_POWERUP_ADCL (0x1 << NAU8821_POWERUP_ADCL_SFT)
+#define NAU8821_POWERUP_ADCR_SFT 4
+#define NAU8821_POWERUP_ADCR (0x1 << NAU8821_POWERUP_ADCR_SFT)
+
+/* RDAC (0x73) */
+#define NAU8821_DACR_EN_SFT 13
+#define NAU8821_DACR_EN (0x3 << NAU8821_DACR_EN_SFT)
+#define NAU8821_DACL_EN_SFT 12
+#define NAU8821_DACL_EN (0x3 << NAU8821_DACL_EN_SFT)
+#define NAU8821_DACR_CLK_EN_SFT 9
+#define NAU8821_DACR_CLK_EN (0x3 << NAU8821_DACR_CLK_EN_SFT)
+#define NAU8821_DACL_CLK_EN_SFT 8
+#define NAU8821_DACL_CLK_EN (0x3 << NAU8821_DACL_CLK_EN_SFT)
+#define NAU8821_DAC_CLK_DELAY_SFT 4
+#define NAU8821_DAC_CLK_DELAY_MASK (0x7 << NAU8821_DAC_CLK_DELAY_SFT)
+#define NAU8821_DAC_VREF_SFT 2
+#define NAU8821_DAC_VREF_MASK (0x3 << NAU8821_DAC_VREF_SFT)
+
+/* MIC_BIAS (0x74) */
+#define NAU8821_MICBIAS_JKR2 (0x1 << 12)
+#define NAU8821_MICBIAS_POWERUP_SFT 8
+#define NAU8821_MICBIAS_VOLTAGE_SFT 0
+#define NAU8821_MICBIAS_VOLTAGE_MASK 0x7
+
+/* BOOST (0x76) */
+#define NAU8821_PRECHARGE_DIS (0x1 << 13)
+#define NAU8821_GLOBAL_BIAS_EN (0x1 << 12)
+#define NAU8821_HP_BOOST_DIS_SFT 9
+#define NAU8821_HP_BOOST_DIS (0x1 << NAU8821_HP_BOOST_DIS_SFT)
+#define NAU8821_HP_BOOST_G_DIS (0x1 << 8)
+#define NAU8821_SHORT_SHUTDOWN_EN (0x1 << 6)
+
+/* FEPGA (0x77) */
+#define NAU8821_FEPGA_MODEL_SFT 4
+#define NAU8821_FEPGA_MODEL_MASK (0xf << NAU8821_FEPGA_MODEL_SFT)
+#define NAU8821_FEPGA_MODER_SFT 0
+#define NAU8821_FEPGA_MODER_MASK 0xf
+
+/* PGA_GAIN (0x7e) */
+#define NAU8821_PGA_GAIN_L_SFT 8
+#define NAU8821_PGA_GAIN_L_MASK (0x3f << NAU8821_PGA_GAIN_L_SFT)
+#define NAU8821_PGA_GAIN_R_SFT 0
+#define NAU8821_PGA_GAIN_R_MASK 0x3f
+
+/* POWER_UP_CONTROL (0x7f) */
+#define NAU8821_PUP_PGA_L_SFT 15
+#define NAU8821_PUP_PGA_L (0x1 << NAU8821_PUP_PGA_L_SFT)
+#define NAU8821_PUP_PGA_R_SFT 14
+#define NAU8821_PUP_PGA_R (0x1 << NAU8821_PUP_PGA_R_SFT)
+#define NAU8821_PUP_INTEG_R_SFT 5
+#define NAU8821_PUP_INTEG_R (0x1 << NAU8821_PUP_INTEG_R_SFT)
+#define NAU8821_PUP_INTEG_L_SFT 4
+#define NAU8821_PUP_INTEG_L (0x1 << NAU8821_PUP_INTEG_L_SFT)
+#define NAU8821_PUP_DRV_INSTG_R_SFT 3
+#define NAU8821_PUP_DRV_INSTG_R (0x1 << NAU8821_PUP_DRV_INSTG_R_SFT)
+#define NAU8821_PUP_DRV_INSTG_L_SFT 2
+#define NAU8821_PUP_DRV_INSTG_L (0x1 << NAU8821_PUP_DRV_INSTG_L_SFT)
+#define NAU8821_PUP_MAIN_DRV_R_SFT 1
+#define NAU8821_PUP_MAIN_DRV_R (0x1 << NAU8821_PUP_MAIN_DRV_R_SFT)
+#define NAU8821_PUP_MAIN_DRV_L_SFT 0
+#define NAU8821_PUP_MAIN_DRV_L 0x1
+
+/* CHARGE_PUMP (0x80) */
+#define NAU8821_JAMNODCLOW (0x1 << 10)
+#define NAU8821_POWER_DOWN_DACR_SFT 9
+#define NAU8821_POWER_DOWN_DACR (0x1 << NAU8821_POWER_DOWN_DACR_SFT)
+#define NAU8821_POWER_DOWN_DACL_SFT 8
+#define NAU8821_POWER_DOWN_DACL (0x1 << NAU8821_POWER_DOWN_DACL_SFT)
+#define NAU8821_CHANRGE_PUMP_EN_SFT 5
+#define NAU8821_CHANRGE_PUMP_EN (0x1 << NAU8821_CHANRGE_PUMP_EN_SFT)
+
+/* GENERAL_STATUS (0x82) */
+#define NAU8821_GPIO2_IN_SFT 1
+#define NAU8821_GPIO2_IN (0x1 << NAU8821_GPIO2_IN_SFT)
+
+#define NUVOTON_CODEC_DAI "nau8821-hifi"
+
+/* System Clock Source */
+enum {
+ NAU8821_CLK_DIS,
+ NAU8821_CLK_MCLK,
+ NAU8821_CLK_INTERNAL,
+ NAU8821_CLK_FLL_MCLK,
+ NAU8821_CLK_FLL_BLK,
+ NAU8821_CLK_FLL_FS,
+};
+
+struct nau8821 {
+ struct device *dev;
+ struct regmap *regmap;
+ struct snd_soc_dapm_context *dapm;
+ struct snd_soc_jack *jack;
+ struct semaphore jd_sem;
+ struct work_struct jdet_work;
+ int irq;
+ int clk_id;
+ int micbias_voltage;
+ int vref_impedance;
+ bool jkdet_enable;
+ bool jkdet_pull_enable;
+ bool jkdet_pull_up;
+ int jkdet_polarity;
+ int jack_insert_debounce;
+ int jack_eject_debounce;
+ int fs;
+ int dmic_clk_threshold;
+};
+
+int nau8821_enable_jack_detect(struct snd_soc_component *component,
+ struct snd_soc_jack *jack);
+
+#endif /* __NAU8821_H__ */
--
2.25.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH] ASoC: nau8821: new driver
2021-08-09 10:10 [PATCH] ASoC: nau8821: new driver Seven Lee
@ 2021-08-09 10:44 ` Amadeusz Sławiński
2021-08-17 5:58 ` Seven Lee
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Amadeusz Sławiński @ 2021-08-09 10:44 UTC (permalink / raw)
To: Seven Lee, broonie
Cc: alsa-devel, scott6986, KCHSU0, lgirdwood, YHCHuang, CTLIN0,
dardar923, supercraig0719
On 8/9/2021 12:10 PM, Seven Lee wrote:
> Add driver for NAU88L21.
>
> Signed-off-by: Seven Lee <wtli@nuvoton.com>
> ---
...
> +
> +static int dmic_clock_control(struct snd_soc_dapm_widget *w,
> + struct snd_kcontrol *k, int event)
> +{
> + struct snd_soc_component *component =
> + snd_soc_dapm_to_component(w->dapm);
> + struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
> + int i, speed_selection, clk_adc_src, clk_adc;
> + unsigned int clk_divider_r03;
> +
> + /* The DMIC clock is gotten from adc clock divided by
> + * CLK_DMIC_SRC (1, 2, 4, 8). The clock has to be equal or
> + * less than nau8821->dmic_clk_threshold.
> + */
> + regmap_read(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
> + &clk_divider_r03);
> + clk_adc_src = (clk_divider_r03 & NAU8821_CLK_ADC_SRC_MASK)
> + >> NAU8821_CLK_ADC_SRC_SFT;
> +
> + switch (clk_adc_src) {
> + case 0:
> + clk_adc = nau8821->fs * 256;
> + break;
> + case 1:
> + clk_adc = (nau8821->fs * 256) >> 1;
> + break;
> + case 2:
> + clk_adc = (nau8821->fs * 256) >> 2;
> + break;
> + case 3:
> + clk_adc = (nau8821->fs * 256) >> 3;
> + break;
> + }
Just do:
clk_adc = (nau8821->fs * 256) >> clk_adc_src;
instead of whole switch?
> +
> + for (i = 0 ; i < 4 ; i++) {
> + if ((clk_adc >> dmic_speed_sel[i].param) <=
> + nau8821->dmic_clk_threshold) {
> + speed_selection = dmic_speed_sel[i].val;
> + break;
> + }
> + }
> +
> + dev_dbg(nau8821->dev,
> + "clk_adc=%d, dmic_clk_threshold = %d, param=%d, val = %d\n",
> + clk_adc, nau8821->dmic_clk_threshold,
> + dmic_speed_sel[i].param, dmic_speed_sel[i].val);
> + regmap_update_bits(nau8821->regmap, NAU8821_R13_DMIC_CTRL,
> + NAU8821_DMIC_SRC_MASK,
> + (speed_selection << NAU8821_DMIC_SRC_SFT));
> +
> + return 0;
> +}
> +
...
> +
> +static int nau8821_clock_check(struct nau8821 *nau8821,
> + int stream, int rate, int osr)
> +{
> + int osrate = 0;
> +
> + if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
> + if (osr >= ARRAY_SIZE(osr_dac_sel))
> + return -EINVAL;
> + osrate = osr_dac_sel[osr].osr;
> + } else {
> + if (osr >= ARRAY_SIZE(osr_adc_sel))
> + return -EINVAL;
> + osrate = osr_adc_sel[osr].osr;
> + }
true and false cases seem to be the same here, you can remove the "if
else" and just leave one of them.
> +
> + if (!osrate || rate * osrate > CLK_DA_AD_MAX) {
> + dev_err(nau8821->dev,
> + "exceed the maximum frequency of CLK_ADC or CLK_DAC\n");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
...
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [PATCH] ASoC: nau8821: new driver
2021-08-09 10:44 ` Amadeusz Sławiński
@ 2021-08-17 5:58 ` Seven Lee
2021-08-18 3:19 ` Seven Lee
2021-08-18 3:30 ` John Hsu
2 siblings, 0 replies; 8+ messages in thread
From: Seven Lee @ 2021-08-17 5:58 UTC (permalink / raw)
To: Amadeusz Sławiński, Seven Lee, broonie
Cc: alsa-devel, KCHSU0, lgirdwood, YHCHuang, CTLIN0, dardar923,
supercraig0719
Amadeusz Sławiński 於 2021/8/9 下午 06:44 寫道:
> On 8/9/2021 12:10 PM, Seven Lee wrote:
>> Add driver for NAU88L21.
>>
>> Signed-off-by: Seven Lee <wtli@nuvoton.com>
>> ---
>
> ...
>
>> +
>> +static int dmic_clock_control(struct snd_soc_dapm_widget *w,
>> + struct snd_kcontrol *k, int event)
>> +{
>> + struct snd_soc_component *component =
>> + snd_soc_dapm_to_component(w->dapm);
>> + struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
>> + int i, speed_selection, clk_adc_src, clk_adc;
>> + unsigned int clk_divider_r03;
>> +
>> + /* The DMIC clock is gotten from adc clock divided by
>> + * CLK_DMIC_SRC (1, 2, 4, 8). The clock has to be equal or
>> + * less than nau8821->dmic_clk_threshold.
>> + */
>> + regmap_read(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
>> + &clk_divider_r03);
>> + clk_adc_src = (clk_divider_r03 & NAU8821_CLK_ADC_SRC_MASK)
>> + >> NAU8821_CLK_ADC_SRC_SFT;
>> +
>> + switch (clk_adc_src) {
>> + case 0:
>> + clk_adc = nau8821->fs * 256;
>> + break;
>> + case 1:
>> + clk_adc = (nau8821->fs * 256) >> 1;
>> + break;
>> + case 2:
>> + clk_adc = (nau8821->fs * 256) >> 2;
>> + break;
>> + case 3:
>> + clk_adc = (nau8821->fs * 256) >> 3;
>> + break;
>> + }
>
> Just do:
> clk_adc = (nau8821->fs * 256) >> clk_adc_src;
> instead of whole switch?
Yes, you are right. I will fix it.
>
>> +
>> + for (i = 0 ; i < 4 ; i++) {
>> + if ((clk_adc >> dmic_speed_sel[i].param) <=
>> + nau8821->dmic_clk_threshold) {
>> + speed_selection = dmic_speed_sel[i].val;
>> + break;
>> + }
>> + }
>> +
>> + dev_dbg(nau8821->dev,
>> + "clk_adc=%d, dmic_clk_threshold = %d, param=%d, val = %d\n",
>> + clk_adc, nau8821->dmic_clk_threshold,
>> + dmic_speed_sel[i].param, dmic_speed_sel[i].val);
>> + regmap_update_bits(nau8821->regmap, NAU8821_R13_DMIC_CTRL,
>> + NAU8821_DMIC_SRC_MASK,
>> + (speed_selection << NAU8821_DMIC_SRC_SFT));
>> +
>> + return 0;
>> +}
>> +
>
> ...
>
>> +
>> +static int nau8821_clock_check(struct nau8821 *nau8821,
>> + int stream, int rate, int osr)
>> +{
>> + int osrate = 0;
>> +
>> + if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
>> + if (osr >= ARRAY_SIZE(osr_dac_sel))
>> + return -EINVAL;
>> + osrate = osr_dac_sel[osr].osr;
>> + } else {
>> + if (osr >= ARRAY_SIZE(osr_adc_sel))
>> + return -EINVAL;
>> + osrate = osr_adc_sel[osr].osr;
>> + }
> true and false cases seem to be the same here, you can remove the "if
> else" and just leave one of them.
The OSR of DAC and ADC can be different. And the ratio corresponding
to the bit is also different. They are two different tables for
osr_dac_sel and osr_adc_sel. Then it should be noted that the OSR and
Fs must be selected carefully so that the max frequency of CLK_ADC or
CLK_DAC are less than or equal to 6.144MHz.
>
>> +
>> + if (!osrate || rate * osrate > CLK_DA_AD_MAX) {
>> + dev_err(nau8821->dev,
>> + "exceed the maximum frequency of CLK_ADC or CLK_DAC\n");
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>
> ...
^ permalink raw reply [flat|nested] 8+ messages in thread* [PATCH] ASoC: nau8821: new driver
2021-08-09 10:44 ` Amadeusz Sławiński
2021-08-17 5:58 ` Seven Lee
@ 2021-08-18 3:19 ` Seven Lee
2021-08-18 3:30 ` John Hsu
2 siblings, 0 replies; 8+ messages in thread
From: Seven Lee @ 2021-08-18 3:19 UTC (permalink / raw)
To: Amadeusz Sławiński, Seven Lee, broonie
Cc: alsa-devel, KCHSU0, lgirdwood, YHCHuang, CTLIN0, dardar923,
supercraig0719
Amadeusz Sławiński 於 2021/8/9 下午 06:44 寫道:
> On 8/9/2021 12:10 PM, Seven Lee wrote:
>> Add driver for NAU88L21.
>>
>> Signed-off-by: Seven Lee <wtli@nuvoton.com>
>> ---
>
> ...
>
>> +
>> +static int dmic_clock_control(struct snd_soc_dapm_widget *w,
>> + struct snd_kcontrol *k, int event)
>> +{
>> + struct snd_soc_component *component =
>> + snd_soc_dapm_to_component(w->dapm);
>> + struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
>> + int i, speed_selection, clk_adc_src, clk_adc;
>> + unsigned int clk_divider_r03;
>> +
>> + /* The DMIC clock is gotten from adc clock divided by
>> + * CLK_DMIC_SRC (1, 2, 4, 8). The clock has to be equal or
>> + * less than nau8821->dmic_clk_threshold.
>> + */
>> + regmap_read(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
>> + &clk_divider_r03);
>> + clk_adc_src = (clk_divider_r03 & NAU8821_CLK_ADC_SRC_MASK)
>> + >> NAU8821_CLK_ADC_SRC_SFT;
>> +
>> + switch (clk_adc_src) {
>> + case 0:
>> + clk_adc = nau8821->fs * 256;
>> + break;
>> + case 1:
>> + clk_adc = (nau8821->fs * 256) >> 1;
>> + break;
>> + case 2:
>> + clk_adc = (nau8821->fs * 256) >> 2;
>> + break;
>> + case 3:
>> + clk_adc = (nau8821->fs * 256) >> 3;
>> + break;
>> + }
>
> Just do:
> clk_adc = (nau8821->fs * 256) >> clk_adc_src;
> instead of whole switch?
Yes, you are right. I will fix it.
>
>> +
>> + for (i = 0 ; i < 4 ; i++) {
>> + if ((clk_adc >> dmic_speed_sel[i].param) <=
>> + nau8821->dmic_clk_threshold) {
>> + speed_selection = dmic_speed_sel[i].val;
>> + break;
>> + }
>> + }
>> +
>> + dev_dbg(nau8821->dev,
>> + "clk_adc=%d, dmic_clk_threshold = %d, param=%d, val = %d\n",
>> + clk_adc, nau8821->dmic_clk_threshold,
>> + dmic_speed_sel[i].param, dmic_speed_sel[i].val);
>> + regmap_update_bits(nau8821->regmap, NAU8821_R13_DMIC_CTRL,
>> + NAU8821_DMIC_SRC_MASK,
>> + (speed_selection << NAU8821_DMIC_SRC_SFT));
>> +
>> + return 0;
>> +}
>> +
>
> ...
>
>> +
>> +static int nau8821_clock_check(struct nau8821 *nau8821,
>> + int stream, int rate, int osr)
>> +{
>> + int osrate = 0;
>> +
>> + if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
>> + if (osr >= ARRAY_SIZE(osr_dac_sel))
>> + return -EINVAL;
>> + osrate = osr_dac_sel[osr].osr;
>> + } else {
>> + if (osr >= ARRAY_SIZE(osr_adc_sel))
>> + return -EINVAL;
>> + osrate = osr_adc_sel[osr].osr;
>> + }
> true and false cases seem to be the same here, you can remove the "if
> else" and just leave one of them.
The OSR of DAC and ADC can be different. And the ratio corresponding
to the bit is also different. They are two different tables for
osr_dac_sel and osr_adc_sel. Then it should be noted that the OSR and
Fs must be selected carefully so that the max frequency of CLK_ADC or
CLK_DAC are less than or equal to 6.144MHz.
>
>> +
>> + if (!osrate || rate * osrate > CLK_DA_AD_MAX) {
>> + dev_err(nau8821->dev,
>> + "exceed the maximum frequency of CLK_ADC or CLK_DAC\n");
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>
> ...
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [PATCH] ASoC: nau8821: new driver
2021-08-09 10:44 ` Amadeusz Sławiński
2021-08-17 5:58 ` Seven Lee
2021-08-18 3:19 ` Seven Lee
@ 2021-08-18 3:30 ` John Hsu
2021-08-18 7:23 ` Amadeusz Sławiński
2 siblings, 1 reply; 8+ messages in thread
From: John Hsu @ 2021-08-18 3:30 UTC (permalink / raw)
To: Amadeusz Sławiński, Seven Lee, broonie
Cc: alsa-devel, scott6986, KCHSU0, lgirdwood, YHCHuang, CTLIN0, dardar923
Hi,
On 8/9/2021 6:44 PM, Amadeusz Sławiński wrote:
> On 8/9/2021 12:10 PM, Seven Lee wrote:
>> Add driver for NAU88L21.
>>
>> Signed-off-by: Seven Lee <wtli@nuvoton.com>
>> ---
>
> ...
>
>> +
>> +static int dmic_clock_control(struct snd_soc_dapm_widget *w,
>> + struct snd_kcontrol *k, int event)
>> +{
>> + struct snd_soc_component *component =
>> + snd_soc_dapm_to_component(w->dapm);
>> + struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
>> + int i, speed_selection, clk_adc_src, clk_adc;
>> + unsigned int clk_divider_r03;
>> +
>> + /* The DMIC clock is gotten from adc clock divided by
>> + * CLK_DMIC_SRC (1, 2, 4, 8). The clock has to be equal or
>> + * less than nau8821->dmic_clk_threshold.
>> + */
>> + regmap_read(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
>> + &clk_divider_r03);
>> + clk_adc_src = (clk_divider_r03 & NAU8821_CLK_ADC_SRC_MASK)
>> + >> NAU8821_CLK_ADC_SRC_SFT;
>> +
>> + switch (clk_adc_src) {
>> + case 0:
>> + clk_adc = nau8821->fs * 256;
>> + break;
>> + case 1:
>> + clk_adc = (nau8821->fs * 256) >> 1;
>> + break;
>> + case 2:
>> + clk_adc = (nau8821->fs * 256) >> 2;
>> + break;
>> + case 3:
>> + clk_adc = (nau8821->fs * 256) >> 3;
>> + break;
>> + }
>
> Just do:
> clk_adc = (nau8821->fs * 256) >> clk_adc_src;
> instead of whole switch?
>
Yes, you are right. I will fix it.
>> +
>> + for (i = 0 ; i < 4 ; i++) {
>> + if ((clk_adc >> dmic_speed_sel[i].param) <=
>> + nau8821->dmic_clk_threshold) {
>> + speed_selection = dmic_speed_sel[i].val;
>> + break;
>> + }
>> + }
>> +
>> + dev_dbg(nau8821->dev,
>> + "clk_adc=%d, dmic_clk_threshold = %d, param=%d, val = %d\n",
>> + clk_adc, nau8821->dmic_clk_threshold,
>> + dmic_speed_sel[i].param, dmic_speed_sel[i].val);
>> + regmap_update_bits(nau8821->regmap, NAU8821_R13_DMIC_CTRL,
>> + NAU8821_DMIC_SRC_MASK,
>> + (speed_selection << NAU8821_DMIC_SRC_SFT));
>> +
>> + return 0;
>> +}
>> +
>
> ...
>
>> +
>> +static int nau8821_clock_check(struct nau8821 *nau8821,
>> + int stream, int rate, int osr)
>> +{
>> + int osrate = 0;
>> +
>> + if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
>> + if (osr >= ARRAY_SIZE(osr_dac_sel))
>> + return -EINVAL;
>> + osrate = osr_dac_sel[osr].osr;
>> + } else {
>> + if (osr >= ARRAY_SIZE(osr_adc_sel))
>> + return -EINVAL;
>> + osrate = osr_adc_sel[osr].osr;
>> + }
> true and false cases seem to be the same here, you can remove the "if
> else" and just leave one of them.
>
The OSR of DAC and ADC can be different. And the ratio corresponding
to the bit is also different. They are two different tables for
osr_dac_sel and osr_adc_sel. Then it should be noted that the OSR and
Fs must be selected carefully so that the max frequency of CLK_ADC or
CLK_DAC are less than or equal to 6.144MHz.
>> +
>> + if (!osrate || rate * osrate > CLK_DA_AD_MAX) {
>> + dev_err(nau8821->dev,
>> + "exceed the maximum frequency of CLK_ADC or CLK_DAC\n");
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>
> ...
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [PATCH] ASoC: nau8821: new driver
2021-08-18 3:30 ` John Hsu
@ 2021-08-18 7:23 ` Amadeusz Sławiński
0 siblings, 0 replies; 8+ messages in thread
From: Amadeusz Sławiński @ 2021-08-18 7:23 UTC (permalink / raw)
To: John Hsu, Seven Lee, broonie
Cc: alsa-devel, scott6986, KCHSU0, lgirdwood, YHCHuang, CTLIN0, dardar923
On 8/18/2021 5:30 AM, John Hsu wrote:
> Hi,
>
> On 8/9/2021 6:44 PM, Amadeusz Sławiński wrote:
>> On 8/9/2021 12:10 PM, Seven Lee wrote:
>>> Add driver for NAU88L21.
>>>
>>> Signed-off-by: Seven Lee <wtli@nuvoton.com>
>>> ---
>>
>> ...
>>
>>> +
>>> +static int dmic_clock_control(struct snd_soc_dapm_widget *w,
>>> + struct snd_kcontrol *k, int event)
>>> +{
>>> + struct snd_soc_component *component =
>>> + snd_soc_dapm_to_component(w->dapm);
>>> + struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
>>> + int i, speed_selection, clk_adc_src, clk_adc;
>>> + unsigned int clk_divider_r03;
>>> +
>>> + /* The DMIC clock is gotten from adc clock divided by
>>> + * CLK_DMIC_SRC (1, 2, 4, 8). The clock has to be equal or
>>> + * less than nau8821->dmic_clk_threshold.
>>> + */
>>> + regmap_read(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
>>> + &clk_divider_r03);
>>> + clk_adc_src = (clk_divider_r03 & NAU8821_CLK_ADC_SRC_MASK)
>>> + >> NAU8821_CLK_ADC_SRC_SFT;
>>> +
>>> + switch (clk_adc_src) {
>>> + case 0:
>>> + clk_adc = nau8821->fs * 256;
>>> + break;
>>> + case 1:
>>> + clk_adc = (nau8821->fs * 256) >> 1;
>>> + break;
>>> + case 2:
>>> + clk_adc = (nau8821->fs * 256) >> 2;
>>> + break;
>>> + case 3:
>>> + clk_adc = (nau8821->fs * 256) >> 3;
>>> + break;
>>> + }
>>
>> Just do:
>> clk_adc = (nau8821->fs * 256) >> clk_adc_src;
>> instead of whole switch?
>>
>
> Yes, you are right. I will fix it.
>>> +
>>> + for (i = 0 ; i < 4 ; i++) {
>>> + if ((clk_adc >> dmic_speed_sel[i].param) <=
>>> + nau8821->dmic_clk_threshold) {
>>> + speed_selection = dmic_speed_sel[i].val;
>>> + break;
>>> + }
>>> + }
>>> +
>>> + dev_dbg(nau8821->dev,
>>> + "clk_adc=%d, dmic_clk_threshold = %d, param=%d, val = %d\n",
>>> + clk_adc, nau8821->dmic_clk_threshold,
>>> + dmic_speed_sel[i].param, dmic_speed_sel[i].val);
>>> + regmap_update_bits(nau8821->regmap, NAU8821_R13_DMIC_CTRL,
>>> + NAU8821_DMIC_SRC_MASK,
>>> + (speed_selection << NAU8821_DMIC_SRC_SFT));
>>> +
>>> + return 0;
>>> +}
>>> +
>>
>> ...
>>
>>> +
>>> +static int nau8821_clock_check(struct nau8821 *nau8821,
>>> + int stream, int rate, int osr)
>>> +{
>>> + int osrate = 0;
>>> +
>>> + if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
>>> + if (osr >= ARRAY_SIZE(osr_dac_sel))
>>> + return -EINVAL;
>>> + osrate = osr_dac_sel[osr].osr;
>>> + } else {
>>> + if (osr >= ARRAY_SIZE(osr_adc_sel))
>>> + return -EINVAL;
>>> + osrate = osr_adc_sel[osr].osr;
>>> + }
>> true and false cases seem to be the same here, you can remove the "if
>> else" and just leave one of them.
>>
>
> The OSR of DAC and ADC can be different. And the ratio corresponding
> to the bit is also different. They are two different tables for
> osr_dac_sel and osr_adc_sel. Then it should be noted that the OSR and
> Fs must be selected carefully so that the max frequency of CLK_ADC or
> CLK_DAC are less than or equal to 6.144MHz.
Right, I somehow did misread dac and adc, and thought that they are the
same table.
>>> +
>>> + if (!osrate || rate * osrate > CLK_DA_AD_MAX) {
>>> + dev_err(nau8821->dev,
>>> + "exceed the maximum frequency of CLK_ADC or CLK_DAC\n");
>>> + return -EINVAL;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>
>> ...
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH] ASoC: nau8821: new driver
@ 2021-10-01 10:31 Seven Lee
2021-10-02 1:37 ` Mark Brown
0 siblings, 1 reply; 8+ messages in thread
From: Seven Lee @ 2021-10-01 10:31 UTC (permalink / raw)
To: broonie
Cc: alsa-devel, scott6986, Seven Lee, KCHSU0, lgirdwood, YHCHuang,
michelle.chen, CTLIN0, dardar923, supercraig0719
The driver is for codec NAU88L21 of Nuvoton Technology Corporation.
The NAU88L21 is an ultra-low power high performance audio codec that
supports both analog and digital audio functions.
Signed-off-by: Seven Lee <wtli@nuvoton.com>
---
.../devicetree/bindings/sound/nau8821.txt | 55 +
sound/soc/codecs/Kconfig | 5 +
sound/soc/codecs/Makefile | 2 +
sound/soc/codecs/nau8821.c | 1712 +++++++++++++++++
sound/soc/codecs/nau8821.h | 533 +++++
5 files changed, 2307 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/nau8821.txt
create mode 100644 sound/soc/codecs/nau8821.c
create mode 100644 sound/soc/codecs/nau8821.h
diff --git a/Documentation/devicetree/bindings/sound/nau8821.txt b/Documentation/devicetree/bindings/sound/nau8821.txt
new file mode 100644
index 000000000000..6c3baf7a5f21
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/nau8821.txt
@@ -0,0 +1,55 @@
+Nuvoton NAU88L21 audio codec
+
+This device supports I2C only.
+
+Required properties:
+ - compatible : Must be "nuvoton,nau8821"
+
+ - reg : the I2C address of the device. This is either 0x1B (CSB=0) or 0x54 (CSB=1).
+
+Optional properties:
+ - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
+ - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
+ otherwise pin in high impedance state.
+ - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
+ - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
+
+ - nuvoton,vref-impedance: VREF Impedance selection
+ 0 - Open
+ 1 - 25 kOhm
+ 2 - 125 kOhm
+ 3 - 2.5 kOhm
+
+ - nuvoton,micbias-voltage: Micbias voltage level.
+ 0 - VDDA
+ 1 - VDDA
+ 2 - VDDA * 1.1
+ 3 - VDDA * 1.2
+ 4 - VDDA * 1.3
+ 5 - VDDA * 1.4
+ 6 - VDDA * 1.53
+ 7 - VDDA * 1.53
+
+ - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+ - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+
+ - nuvoton,dmic-clk-threshold: the ADC threshold of DMIC clock.
+
+
+Example:
+
+ headset: nau8821@1b {
+ compatible = "nuvoton,nau8821";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+ nuvoton,jkdet-enable;
+ nuvoton,jkdet-pull-enable;
+ nuvoton,jkdet-pull-up;
+ nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
+ nuvoton,vref-impedance = <2>;
+ nuvoton,micbias-voltage = <6>;
+ nuvoton,jack-insert-debounce = <7>;
+ nuvoton,jack-eject-debounce = <7>;
+ nuvoton,dmic-clk-threshold = 3072000;
+ };
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index deda5ee02ebb..75506bd8fc0d 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -138,6 +138,7 @@ config SND_SOC_ALL_CODECS
imply SND_SOC_NAU8315
imply SND_SOC_NAU8540
imply SND_SOC_NAU8810
+ imply SND_SOC_NAU8821
imply SND_SOC_NAU8822
imply SND_SOC_NAU8824
imply SND_SOC_NAU8825
@@ -1922,6 +1923,10 @@ config SND_SOC_NAU8810
tristate "Nuvoton Technology Corporation NAU88C10 CODEC"
depends on I2C
+config SND_SOC_NAU8821
+ tristate "Nuvoton Technology Corporation NAU88L21 CODEC"
+ depends on I2C
+
config SND_SOC_NAU8822
tristate "Nuvoton Technology Corporation NAU88C22 CODEC"
depends on I2C
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile
index 4cf939d0d3fb..90eedab4ee7a 100644
--- a/sound/soc/codecs/Makefile
+++ b/sound/soc/codecs/Makefile
@@ -143,6 +143,7 @@ snd-soc-mt6660-objs := mt6660.o
snd-soc-nau8315-objs := nau8315.o
snd-soc-nau8540-objs := nau8540.o
snd-soc-nau8810-objs := nau8810.o
+snd-soc-nau8821-objs := nau8821.o
snd-soc-nau8822-objs := nau8822.o
snd-soc-nau8824-objs := nau8824.o
snd-soc-nau8825-objs := nau8825.o
@@ -473,6 +474,7 @@ obj-$(CONFIG_SND_SOC_MT6660) += snd-soc-mt6660.o
obj-$(CONFIG_SND_SOC_NAU8315) += snd-soc-nau8315.o
obj-$(CONFIG_SND_SOC_NAU8540) += snd-soc-nau8540.o
obj-$(CONFIG_SND_SOC_NAU8810) += snd-soc-nau8810.o
+obj-$(CONFIG_SND_SOC_NAU8821) += snd-soc-nau8821.o
obj-$(CONFIG_SND_SOC_NAU8822) += snd-soc-nau8822.o
obj-$(CONFIG_SND_SOC_NAU8824) += snd-soc-nau8824.o
obj-$(CONFIG_SND_SOC_NAU8825) += snd-soc-nau8825.o
diff --git a/sound/soc/codecs/nau8821.c b/sound/soc/codecs/nau8821.c
new file mode 100644
index 000000000000..4ea56d2f9509
--- /dev/null
+++ b/sound/soc/codecs/nau8821.c
@@ -0,0 +1,1712 @@
+// SPDX-License-Identifier: GPL-2.0-only
+//
+// nau8821.c -- Nuvoton NAU88L21 audio codec driver
+//
+// Copyright 2021 Nuvoton Technology Corp.
+// Author: John Hsu <kchsu0@nuvoton.com>
+// Co-author: Seven Lee <wtli@nuvoton.com>
+//
+
+#include <linux/acpi.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/math64.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <sound/core.h>
+#include <sound/initval.h>
+#include <sound/jack.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/tlv.h>
+#include "nau8821.h"
+
+#define NAU_FREF_MAX 13500000
+#define NAU_FVCO_MAX 100000000
+#define NAU_FVCO_MIN 90000000
+
+/* the maximum frequency of CLK_ADC and CLK_DAC */
+#define CLK_DA_AD_MAX 6144000
+
+static int nau8821_configure_sysclk(struct nau8821 *nau8821,
+ int clk_id, unsigned int freq);
+
+struct nau8821_fll {
+ int mclk_src;
+ int ratio;
+ int fll_frac;
+ int fll_int;
+ int clk_ref_div;
+};
+
+struct nau8821_fll_attr {
+ unsigned int param;
+ unsigned int val;
+};
+
+/* scaling for mclk from sysclk_src output */
+static const struct nau8821_fll_attr mclk_src_scaling[] = {
+ { 1, 0x0 },
+ { 2, 0x2 },
+ { 4, 0x3 },
+ { 8, 0x4 },
+ { 16, 0x5 },
+ { 32, 0x6 },
+ { 3, 0x7 },
+ { 6, 0xa },
+ { 12, 0xb },
+ { 24, 0xc },
+ { 48, 0xd },
+ { 96, 0xe },
+ { 5, 0xf },
+};
+
+/* ratio for input clk freq */
+static const struct nau8821_fll_attr fll_ratio[] = {
+ { 512000, 0x01 },
+ { 256000, 0x02 },
+ { 128000, 0x04 },
+ { 64000, 0x08 },
+ { 32000, 0x10 },
+ { 8000, 0x20 },
+ { 4000, 0x40 },
+};
+
+static const struct nau8821_fll_attr fll_pre_scalar[] = {
+ { 0, 0x0 },
+ { 1, 0x1 },
+ { 2, 0x2 },
+ { 3, 0x3 },
+};
+
+/* over sampling rate */
+struct nau8821_osr_attr {
+ unsigned int osr;
+ unsigned int clk_src;
+};
+
+static const struct nau8821_osr_attr osr_dac_sel[] = {
+ { 64, 2 }, /* OSR 64, SRC 1/4 */
+ { 256, 0 }, /* OSR 256, SRC 1 */
+ { 128, 1 }, /* OSR 128, SRC 1/2 */
+ { 0, 0 },
+ { 32, 3 }, /* OSR 32, SRC 1/8 */
+};
+
+static const struct nau8821_osr_attr osr_adc_sel[] = {
+ { 32, 3 }, /* OSR 32, SRC 1/8 */
+ { 64, 2 }, /* OSR 64, SRC 1/4 */
+ { 128, 1 }, /* OSR 128, SRC 1/2 */
+ { 256, 0 }, /* OSR 256, SRC 1 */
+};
+
+struct nau8821_dmic_speed {
+ unsigned int param;
+ unsigned int val;
+};
+
+static const struct nau8821_dmic_speed dmic_speed_sel[] = {
+ { 0, 0x0 }, /*SPEED 1, SRC 1 */
+ { 1, 0x1 }, /*SPEED 2, SRC 1/2 */
+ { 2, 0x2 }, /*SPEED 4, SRC 1/4 */
+ { 3, 0x3 }, /*SPEED 8, SRC 1/8 */
+};
+
+static const struct reg_default nau8821_reg_defaults[] = {
+ { NAU8821_R01_ENA_CTRL, 0x00ff },
+ { NAU8821_R03_CLK_DIVIDER, 0x0050 },
+ { NAU8821_R04_FLL1, 0x0 },
+ { NAU8821_R05_FLL2, 0x00bc },
+ { NAU8821_R06_FLL3, 0x0008 },
+ { NAU8821_R07_FLL4, 0x0010 },
+ { NAU8821_R08_FLL5, 0x4000 },
+ { NAU8821_R09_FLL6, 0x6900 },
+ { NAU8821_R0A_FLL7, 0x0031 },
+ { NAU8821_R0B_FLL8, 0x26e9 },
+ { NAU8821_R0D_JACK_DET_CTRL, 0x0 },
+ { NAU8821_R0F_INTERRUPT_MASK, 0x0 },
+ { NAU8821_R12_INTERRUPT_DIS_CTRL, 0xffff },
+ { NAU8821_R13_DMIC_CTRL, 0x0 },
+ { NAU8821_R1A_GPIO12_CTRL, 0x0 },
+ { NAU8821_R1B_TDM_CTRL, 0x0 },
+ { NAU8821_R1C_I2S_PCM_CTRL1, 0x000a },
+ { NAU8821_R1D_I2S_PCM_CTRL2, 0x8010 },
+ { NAU8821_R1E_LEFT_TIME_SLOT, 0x0 },
+ { NAU8821_R1F_RIGHT_TIME_SLOT, 0x0 },
+ { NAU8821_R21_BIQ0_COF1, 0x0 },
+ { NAU8821_R22_BIQ0_COF2, 0x0 },
+ { NAU8821_R23_BIQ0_COF3, 0x0 },
+ { NAU8821_R24_BIQ0_COF4, 0x0 },
+ { NAU8821_R25_BIQ0_COF5, 0x0 },
+ { NAU8821_R26_BIQ0_COF6, 0x0 },
+ { NAU8821_R27_BIQ0_COF7, 0x0 },
+ { NAU8821_R28_BIQ0_COF8, 0x0 },
+ { NAU8821_R29_BIQ0_COF9, 0x0 },
+ { NAU8821_R2A_BIQ0_COF10, 0x0 },
+ { NAU8821_R2B_ADC_RATE, 0x0002 },
+ { NAU8821_R2C_DAC_CTRL1, 0x0082 },
+ { NAU8821_R2D_DAC_CTRL2, 0x0 },
+ { NAU8821_R2F_DAC_DGAIN_CTRL, 0x0 },
+ { NAU8821_R30_ADC_DGAIN_CTRL, 0x0 },
+ { NAU8821_R31_MUTE_CTRL, 0x0 },
+ { NAU8821_R32_HSVOL_CTRL, 0x0 },
+ { NAU8821_R34_DACR_CTRL, 0xcfcf },
+ { NAU8821_R35_ADC_DGAIN_CTRL1, 0xcfcf },
+ { NAU8821_R36_ADC_DRC_KNEE_IP12, 0x1486 },
+ { NAU8821_R37_ADC_DRC_KNEE_IP34, 0x0f12 },
+ { NAU8821_R38_ADC_DRC_SLOPES, 0x25ff },
+ { NAU8821_R39_ADC_DRC_ATKDCY, 0x3457 },
+ { NAU8821_R3A_DAC_DRC_KNEE_IP12, 0x1486 },
+ { NAU8821_R3B_DAC_DRC_KNEE_IP34, 0x0f12 },
+ { NAU8821_R3C_DAC_DRC_SLOPES, 0x25f9 },
+ { NAU8821_R3D_DAC_DRC_ATKDCY, 0x3457 },
+ { NAU8821_R41_BIQ1_COF1, 0x0 },
+ { NAU8821_R42_BIQ1_COF2, 0x0 },
+ { NAU8821_R43_BIQ1_COF3, 0x0 },
+ { NAU8821_R44_BIQ1_COF4, 0x0 },
+ { NAU8821_R45_BIQ1_COF5, 0x0 },
+ { NAU8821_R46_BIQ1_COF6, 0x0 },
+ { NAU8821_R47_BIQ1_COF7, 0x0 },
+ { NAU8821_R48_BIQ1_COF8, 0x0 },
+ { NAU8821_R49_BIQ1_COF9, 0x0 },
+ { NAU8821_R4A_BIQ1_COF10, 0x0 },
+ { NAU8821_R4B_CLASSG_CTRL, 0x0 },
+ { NAU8821_R4C_IMM_MODE_CTRL, 0x0 },
+ { NAU8821_R4D_IMM_RMS_L, 0x0 },
+ { NAU8821_R53_OTPDOUT_1, 0xaad8 },
+ { NAU8821_R54_OTPDOUT_2, 0x0002 },
+ { NAU8821_R55_MISC_CTRL, 0x0 },
+ { NAU8821_R66_BIAS_ADJ, 0x0 },
+ { NAU8821_R68_TRIM_SETTINGS, 0x0 },
+ { NAU8821_R69_ANALOG_CONTROL_1, 0x0 },
+ { NAU8821_R6A_ANALOG_CONTROL_2, 0x0 },
+ { NAU8821_R6B_PGA_MUTE, 0x0 },
+ { NAU8821_R71_ANALOG_ADC_1, 0x0011 },
+ { NAU8821_R72_ANALOG_ADC_2, 0x0020 },
+ { NAU8821_R73_RDAC, 0x0008 },
+ { NAU8821_R74_MIC_BIAS, 0x0006 },
+ { NAU8821_R76_BOOST, 0x0 },
+ { NAU8821_R77_FEPGA, 0x0 },
+ { NAU8821_R7E_PGA_GAIN, 0x0 },
+ { NAU8821_R7F_POWER_UP_CONTROL, 0x0 },
+ { NAU8821_R80_CHARGE_PUMP, 0x0 },
+};
+
+static bool nau8821_readable_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case NAU8821_R00_RESET ... NAU8821_R01_ENA_CTRL:
+ case NAU8821_R03_CLK_DIVIDER ... NAU8821_R0B_FLL8:
+ case NAU8821_R0D_JACK_DET_CTRL:
+ case NAU8821_R0F_INTERRUPT_MASK ... NAU8821_R13_DMIC_CTRL:
+ case NAU8821_R1A_GPIO12_CTRL ... NAU8821_R1F_RIGHT_TIME_SLOT:
+ case NAU8821_R21_BIQ0_COF1 ... NAU8821_R2D_DAC_CTRL2:
+ case NAU8821_R2F_DAC_DGAIN_CTRL ... NAU8821_R32_HSVOL_CTRL:
+ case NAU8821_R34_DACR_CTRL ... NAU8821_R3D_DAC_DRC_ATKDCY:
+ case NAU8821_R41_BIQ1_COF1 ... NAU8821_R4F_FUSE_CTRL3:
+ case NAU8821_R51_FUSE_CTRL1:
+ case NAU8821_R53_OTPDOUT_1 ... NAU8821_R55_MISC_CTRL:
+ case NAU8821_R58_I2C_DEVICE_ID ... NAU8821_R5A_SOFTWARE_RST:
+ case NAU8821_R66_BIAS_ADJ:
+ case NAU8821_R68_TRIM_SETTINGS ... NAU8821_R6B_PGA_MUTE:
+ case NAU8821_R71_ANALOG_ADC_1 ... NAU8821_R74_MIC_BIAS:
+ case NAU8821_R76_BOOST ... NAU8821_R77_FEPGA:
+ case NAU8821_R7E_PGA_GAIN ... NAU8821_R82_GENERAL_STATUS:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static bool nau8821_writeable_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case NAU8821_R00_RESET ... NAU8821_R01_ENA_CTRL:
+ case NAU8821_R03_CLK_DIVIDER ... NAU8821_R0B_FLL8:
+ case NAU8821_R0D_JACK_DET_CTRL:
+ case NAU8821_R0F_INTERRUPT_MASK:
+ case NAU8821_R11_INT_CLR_KEY_STATUS ... NAU8821_R13_DMIC_CTRL:
+ case NAU8821_R1A_GPIO12_CTRL ... NAU8821_R1F_RIGHT_TIME_SLOT:
+ case NAU8821_R21_BIQ0_COF1 ... NAU8821_R2D_DAC_CTRL2:
+ case NAU8821_R2F_DAC_DGAIN_CTRL ... NAU8821_R32_HSVOL_CTRL:
+ case NAU8821_R34_DACR_CTRL ... NAU8821_R3D_DAC_DRC_ATKDCY:
+ case NAU8821_R41_BIQ1_COF1 ... NAU8821_R4C_IMM_MODE_CTRL:
+ case NAU8821_R4E_FUSE_CTRL2 ... NAU8821_R4F_FUSE_CTRL3:
+ case NAU8821_R51_FUSE_CTRL1:
+ case NAU8821_R55_MISC_CTRL:
+ case NAU8821_R5A_SOFTWARE_RST:
+ case NAU8821_R66_BIAS_ADJ:
+ case NAU8821_R68_TRIM_SETTINGS ... NAU8821_R6B_PGA_MUTE:
+ case NAU8821_R71_ANALOG_ADC_1 ... NAU8821_R74_MIC_BIAS:
+ case NAU8821_R76_BOOST ... NAU8821_R77_FEPGA:
+ case NAU8821_R7E_PGA_GAIN ... NAU8821_R80_CHARGE_PUMP:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static bool nau8821_volatile_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case NAU8821_R00_RESET:
+ case NAU8821_R10_IRQ_STATUS ... NAU8821_R11_INT_CLR_KEY_STATUS:
+ case NAU8821_R21_BIQ0_COF1 ... NAU8821_R2A_BIQ0_COF10:
+ case NAU8821_R41_BIQ1_COF1 ... NAU8821_R4A_BIQ1_COF10:
+ case NAU8821_R4D_IMM_RMS_L:
+ case NAU8821_R53_OTPDOUT_1 ... NAU8821_R54_OTPDOUT_2:
+ case NAU8821_R58_I2C_DEVICE_ID ... NAU8821_R5A_SOFTWARE_RST:
+ case NAU8821_R81_CHARGE_PUMP_INPUT_READ ... NAU8821_R82_GENERAL_STATUS:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static int nau8821_biq_coeff_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
+ struct soc_bytes_ext *params = (void *)kcontrol->private_value;
+
+ if (!component->regmap)
+ return -EINVAL;
+
+ regmap_raw_read(component->regmap, NAU8821_R21_BIQ0_COF1,
+ ucontrol->value.bytes.data, params->max);
+
+ return 0;
+}
+
+static int nau8821_biq_coeff_put(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
+ struct soc_bytes_ext *params = (void *)kcontrol->private_value;
+ void *data;
+
+ if (!component->regmap)
+ return -EINVAL;
+
+ data = kmemdup(ucontrol->value.bytes.data,
+ params->max, GFP_KERNEL | GFP_DMA);
+ if (!data)
+ return -ENOMEM;
+
+ regmap_raw_write(component->regmap, NAU8821_R21_BIQ0_COF1,
+ data, params->max);
+
+ kfree(data);
+
+ return 0;
+}
+
+static const char * const nau8821_adc_decimation[] = {
+ "32", "64", "128", "256" };
+
+static const struct soc_enum nau8821_adc_decimation_enum =
+ SOC_ENUM_SINGLE(NAU8821_R2B_ADC_RATE, NAU8821_ADC_SYNC_DOWN_SFT,
+ ARRAY_SIZE(nau8821_adc_decimation), nau8821_adc_decimation);
+
+static const char * const nau8821_dac_oversampl[] = {
+ "64", "256", "128", "", "32" };
+
+static const struct soc_enum nau8821_dac_oversampl_enum =
+ SOC_ENUM_SINGLE(NAU8821_R2C_DAC_CTRL1, NAU8821_DAC_OVERSAMPLE_SFT,
+ ARRAY_SIZE(nau8821_dac_oversampl), nau8821_dac_oversampl);
+
+static const DECLARE_TLV_DB_MINMAX_MUTE(adc_vol_tlv, -6600, 2400);
+static const DECLARE_TLV_DB_MINMAX_MUTE(sidetone_vol_tlv, -4200, 0);
+static const DECLARE_TLV_DB_MINMAX(hp_vol_tlv, -900, 0);
+static const DECLARE_TLV_DB_SCALE(playback_vol_tlv, -6600, 50, 1);
+static const DECLARE_TLV_DB_MINMAX(fepga_gain_tlv, -100, 3600);
+static const DECLARE_TLV_DB_MINMAX_MUTE(crosstalk_vol_tlv, -7000, 2400);
+
+static const struct snd_kcontrol_new nau8821_controls[] = {
+ SOC_DOUBLE_TLV("Mic Volume", NAU8821_R35_ADC_DGAIN_CTRL1,
+ NAU8821_ADCL_CH_VOL_SFT, NAU8821_ADCR_CH_VOL_SFT,
+ 0xff, 0, adc_vol_tlv),
+ SOC_DOUBLE_TLV("Headphone Bypass Volume", NAU8821_R30_ADC_DGAIN_CTRL,
+ 12, 8, 0x0f, 0, sidetone_vol_tlv),
+ SOC_DOUBLE_TLV("Headphone Volume", NAU8821_R32_HSVOL_CTRL,
+ NAU8821_HPL_VOL_SFT, NAU8821_HPR_VOL_SFT, 0x3, 1, hp_vol_tlv),
+ SOC_DOUBLE_TLV("Digital Playback Volume", NAU8821_R34_DACR_CTRL,
+ NAU8821_DACL_CH_VOL_SFT, NAU8821_DACR_CH_VOL_SFT,
+ 0xcf, 0, playback_vol_tlv),
+ SOC_DOUBLE_TLV("Frontend PGA Volume", NAU8821_R7E_PGA_GAIN,
+ NAU8821_PGA_GAIN_L_SFT, NAU8821_PGA_GAIN_R_SFT,
+ 37, 0, fepga_gain_tlv),
+ SOC_DOUBLE_TLV("Headphone Crosstalk Volume",
+ NAU8821_R2F_DAC_DGAIN_CTRL,
+ 0, 8, 0xff, 0, crosstalk_vol_tlv),
+
+ SOC_ENUM("ADC Decimation Rate", nau8821_adc_decimation_enum),
+ SOC_ENUM("DAC Oversampling Rate", nau8821_dac_oversampl_enum),
+ SND_SOC_BYTES_EXT("BIQ Coefficients", 20,
+ nau8821_biq_coeff_get, nau8821_biq_coeff_put),
+ SOC_SINGLE("ADC Phase Switch", NAU8821_R1B_TDM_CTRL,
+ NAU8821_ADCPHS_SFT, 1, 0),
+};
+
+static const struct snd_kcontrol_new nau8821_dmic_mode_switch =
+ SOC_DAPM_SINGLE("Switch", NAU8821_R13_DMIC_CTRL,
+ NAU8821_DMIC_EN_SFT, 1, 0);
+
+static int dmic_clock_control(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *k, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ int i, speed_selection = -1, clk_adc_src, clk_adc;
+ unsigned int clk_divider_r03;
+
+ /* The DMIC clock is gotten from adc clock divided by
+ * CLK_DMIC_SRC (1, 2, 4, 8). The clock has to be equal or
+ * less than nau8821->dmic_clk_threshold.
+ */
+ regmap_read(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
+ &clk_divider_r03);
+ clk_adc_src = (clk_divider_r03 & NAU8821_CLK_ADC_SRC_MASK)
+ >> NAU8821_CLK_ADC_SRC_SFT;
+ clk_adc = (nau8821->fs * 256) >> clk_adc_src;
+
+ for (i = 0 ; i < 4 ; i++)
+ if ((clk_adc >> dmic_speed_sel[i].param) <=
+ nau8821->dmic_clk_threshold) {
+ speed_selection = dmic_speed_sel[i].val;
+ break;
+ }
+ if (speed_selection < 0)
+ return -EINVAL;
+
+ dev_dbg(nau8821->dev,
+ "clk_adc=%d, dmic_clk_threshold = %d, param=%d, val = %d\n",
+ clk_adc, nau8821->dmic_clk_threshold,
+ dmic_speed_sel[i].param, dmic_speed_sel[i].val);
+ regmap_update_bits(nau8821->regmap, NAU8821_R13_DMIC_CTRL,
+ NAU8821_DMIC_SRC_MASK,
+ (speed_selection << NAU8821_DMIC_SRC_SFT));
+
+ return 0;
+}
+
+static int nau8821_left_adc_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ switch (event) {
+ case SND_SOC_DAPM_POST_PMU:
+ msleep(125);
+ regmap_update_bits(nau8821->regmap, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_ADCL, NAU8821_EN_ADCL);
+ break;
+ case SND_SOC_DAPM_POST_PMD:
+ regmap_update_bits(nau8821->regmap,
+ NAU8821_R01_ENA_CTRL, NAU8821_EN_ADCL, 0);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int nau8821_right_adc_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ switch (event) {
+ case SND_SOC_DAPM_POST_PMU:
+ msleep(125);
+ regmap_update_bits(nau8821->regmap, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_ADCR, NAU8821_EN_ADCR);
+ break;
+ case SND_SOC_DAPM_POST_PMD:
+ regmap_update_bits(nau8821->regmap,
+ NAU8821_R01_ENA_CTRL, NAU8821_EN_ADCR, 0);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int nau8821_pump_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 =
+ snd_soc_component_get_drvdata(component);
+
+ switch (event) {
+ case SND_SOC_DAPM_POST_PMU:
+ /* Prevent startup click by letting charge pump to ramp up */
+ msleep(20);
+ regmap_update_bits(nau8821->regmap, NAU8821_R80_CHARGE_PUMP,
+ NAU8821_JAMNODCLOW, NAU8821_JAMNODCLOW);
+ break;
+ case SND_SOC_DAPM_PRE_PMD:
+ regmap_update_bits(nau8821->regmap, NAU8821_R80_CHARGE_PUMP,
+ NAU8821_JAMNODCLOW, 0);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int nau8821_output_dac_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct snd_soc_component *component =
+ snd_soc_dapm_to_component(w->dapm);
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ switch (event) {
+ case SND_SOC_DAPM_PRE_PMU:
+ /* Disables the TESTDAC to let DAC signal pass through. */
+ regmap_update_bits(nau8821->regmap, NAU8821_R66_BIAS_ADJ,
+ NAU8821_BIAS_TESTDAC_EN, 0);
+ break;
+ case SND_SOC_DAPM_POST_PMD:
+ regmap_update_bits(nau8821->regmap, NAU8821_R66_BIAS_ADJ,
+ NAU8821_BIAS_TESTDAC_EN, NAU8821_BIAS_TESTDAC_EN);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static const struct snd_soc_dapm_widget nau8821_dapm_widgets[] = {
+ SND_SOC_DAPM_SUPPLY("MICBIAS", NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_POWERUP_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_SUPPLY("DMIC Clock", SND_SOC_NOPM, 0, 0,
+ dmic_clock_control, SND_SOC_DAPM_POST_PMU),
+ SND_SOC_DAPM_ADC("ADCL Power", NULL, NAU8821_R72_ANALOG_ADC_2,
+ NAU8821_POWERUP_ADCL_SFT, 0),
+ SND_SOC_DAPM_ADC("ADCR Power", NULL, NAU8821_R72_ANALOG_ADC_2,
+ NAU8821_POWERUP_ADCR_SFT, 0),
+ SND_SOC_DAPM_PGA_S("Frontend PGA L", 1, NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_PGA_L_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Frontend PGA R", 1, NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_PGA_R_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("ADCL Digital path", 0, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_ADCL_SFT, 0, nau8821_left_adc_event,
+ SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD),
+ SND_SOC_DAPM_PGA_S("ADCR Digital path", 0, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_ADCR_SFT, 0, nau8821_right_adc_event,
+ SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD),
+ SND_SOC_DAPM_SWITCH("DMIC Enable", SND_SOC_NOPM,
+ 0, 0, &nau8821_dmic_mode_switch),
+ SND_SOC_DAPM_AIF_OUT("AIFTX", "Capture", 0, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_TRISTATE_SFT, 1),
+ SND_SOC_DAPM_AIF_IN("AIFRX", "Playback", 0, SND_SOC_NOPM, 0, 0),
+
+ SND_SOC_DAPM_PGA_S("ADACL", 2, NAU8821_R73_RDAC,
+ NAU8821_DACL_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("ADACR", 2, NAU8821_R73_RDAC,
+ NAU8821_DACR_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("ADACL Clock", 3, NAU8821_R73_RDAC,
+ NAU8821_DACL_CLK_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("ADACR Clock", 3, NAU8821_R73_RDAC,
+ NAU8821_DACR_CLK_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_DAC("DDACR", NULL, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_DACR_SFT, 0),
+ SND_SOC_DAPM_DAC("DDACL", NULL, NAU8821_R01_ENA_CTRL,
+ NAU8821_EN_DACL_SFT, 0),
+ SND_SOC_DAPM_PGA_S("HP amp L", 0, NAU8821_R4B_CLASSG_CTRL,
+ NAU8821_CLASSG_LDAC_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("HP amp R", 0, NAU8821_R4B_CLASSG_CTRL,
+ NAU8821_CLASSG_RDAC_EN_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Charge Pump", 1, NAU8821_R80_CHARGE_PUMP,
+ NAU8821_CHANRGE_PUMP_EN_SFT, 0, nau8821_pump_event,
+ SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
+ SND_SOC_DAPM_PGA_S("Output Driver R Stage 1", 4,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_INTEG_R_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver L Stage 1", 4,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_INTEG_L_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver R Stage 2", 5,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_DRV_INSTG_R_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver L Stage 2", 5,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_DRV_INSTG_L_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver R Stage 3", 6,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_MAIN_DRV_R_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output Driver L Stage 3", 6,
+ NAU8821_R7F_POWER_UP_CONTROL,
+ NAU8821_PUP_MAIN_DRV_L_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("Output DACL", 7,
+ NAU8821_R80_CHARGE_PUMP, NAU8821_POWER_DOWN_DACL_SFT,
+ 0, nau8821_output_dac_event,
+ SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
+ SND_SOC_DAPM_PGA_S("Output DACR", 7,
+ NAU8821_R80_CHARGE_PUMP, NAU8821_POWER_DOWN_DACR_SFT,
+ 0, nau8821_output_dac_event,
+ SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
+
+ /* HPOL/R are ungrounded by disabling 16 Ohm pull-downs on playback */
+ SND_SOC_DAPM_PGA_S("HPOL Pulldown", 8,
+ NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_SPKR_DWN1L_SFT, 0, NULL, 0),
+ SND_SOC_DAPM_PGA_S("HPOR Pulldown", 8,
+ NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_SPKR_DWN1R_SFT, 0, NULL, 0),
+
+ /* High current HPOL/R boost driver */
+ SND_SOC_DAPM_PGA_S("HP Boost Driver", 9,
+ NAU8821_R76_BOOST, NAU8821_HP_BOOST_DIS_SFT, 1, NULL, 0),
+ SND_SOC_DAPM_PGA("Class G", NAU8821_R4B_CLASSG_CTRL,
+ NAU8821_CLASSG_EN_SFT, 0, NULL, 0),
+
+ SND_SOC_DAPM_INPUT("MICL"),
+ SND_SOC_DAPM_INPUT("MICR"),
+ SND_SOC_DAPM_INPUT("DMIC"),
+ SND_SOC_DAPM_OUTPUT("HPOL"),
+ SND_SOC_DAPM_OUTPUT("HPOR"),
+};
+
+static const struct snd_soc_dapm_route nau8821_dapm_routes[] = {
+ {"DMIC Enable", "Switch", "DMIC"},
+ {"DMIC Enable", NULL, "DMIC Clock"},
+
+ {"Frontend PGA L", NULL, "MICL"},
+ {"Frontend PGA R", NULL, "MICR"},
+ {"Frontend PGA L", NULL, "MICBIAS"},
+ {"Frontend PGA R", NULL, "MICBIAS"},
+
+ {"ADCL Power", NULL, "Frontend PGA L"},
+ {"ADCR Power", NULL, "Frontend PGA R"},
+
+ {"ADCL Digital path", NULL, "ADCL Power"},
+ {"ADCR Digital path", NULL, "ADCR Power"},
+ {"ADCL Digital path", NULL, "DMIC Enable"},
+ {"ADCR Digital path", NULL, "DMIC Enable"},
+
+ {"AIFTX", NULL, "ADCL Digital path"},
+ {"AIFTX", NULL, "ADCR Digital path"},
+
+ {"DDACL", NULL, "AIFRX"},
+ {"DDACR", NULL, "AIFRX"},
+
+ {"HP amp L", NULL, "DDACL"},
+ {"HP amp R", NULL, "DDACR"},
+
+ {"Charge Pump", NULL, "HP amp L"},
+ {"Charge Pump", NULL, "HP amp R"},
+
+ {"ADACL", NULL, "Charge Pump"},
+ {"ADACR", NULL, "Charge Pump"},
+ {"ADACL Clock", NULL, "ADACL"},
+ {"ADACR Clock", NULL, "ADACR"},
+
+ {"Output Driver L Stage 1", NULL, "ADACL Clock"},
+ {"Output Driver R Stage 1", NULL, "ADACR Clock"},
+ {"Output Driver L Stage 2", NULL, "Output Driver L Stage 1"},
+ {"Output Driver R Stage 2", NULL, "Output Driver R Stage 1"},
+ {"Output Driver L Stage 3", NULL, "Output Driver L Stage 2"},
+ {"Output Driver R Stage 3", NULL, "Output Driver R Stage 2"},
+ {"Output DACL", NULL, "Output Driver L Stage 3"},
+ {"Output DACR", NULL, "Output Driver R Stage 3"},
+
+ {"HPOL Pulldown", NULL, "Output DACL"},
+ {"HPOR Pulldown", NULL, "Output DACR"},
+ {"HP Boost Driver", NULL, "HPOL Pulldown"},
+ {"HP Boost Driver", NULL, "HPOR Pulldown"},
+
+ {"Class G", NULL, "HP Boost Driver"},
+ {"HPOL", NULL, "Class G"},
+ {"HPOR", NULL, "Class G"},
+};
+
+static int nau8821_clock_check(struct nau8821 *nau8821,
+ int stream, int rate, int osr)
+{
+ int osrate = 0;
+
+ if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
+ if (osr >= ARRAY_SIZE(osr_dac_sel))
+ return -EINVAL;
+ osrate = osr_dac_sel[osr].osr;
+ } else {
+ if (osr >= ARRAY_SIZE(osr_adc_sel))
+ return -EINVAL;
+ osrate = osr_adc_sel[osr].osr;
+ }
+
+ if (!osrate || rate * osrate > CLK_DA_AD_MAX) {
+ dev_err(nau8821->dev,
+ "exceed the maximum frequency of CLK_ADC or CLK_DAC");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int nau8821_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params, struct snd_soc_dai *dai)
+{
+ struct snd_soc_component *component = dai->component;
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ unsigned int val_len = 0, osr, ctrl_val, bclk_fs, clk_div;
+
+ nau8821->fs = params_rate(params);
+ /* CLK_DAC or CLK_ADC = OSR * FS
+ * DAC or ADC clock frequency is defined as Over Sampling Rate (OSR)
+ * multiplied by the audio sample rate (Fs). Note that the OSR and Fs
+ * values must be selected such that the maximum frequency is less
+ * than 6.144 MHz.
+ */
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
+ regmap_read(nau8821->regmap, NAU8821_R2C_DAC_CTRL1, &osr);
+ osr &= NAU8821_DAC_OVERSAMPLE_MASK;
+ if (nau8821_clock_check(nau8821, substream->stream,
+ nau8821->fs, osr)) {
+ return -EINVAL;
+ }
+ regmap_update_bits(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_DAC_SRC_MASK,
+ osr_dac_sel[osr].clk_src << NAU8821_CLK_DAC_SRC_SFT);
+ } else {
+ regmap_read(nau8821->regmap, NAU8821_R2B_ADC_RATE, &osr);
+ osr &= NAU8821_ADC_SYNC_DOWN_MASK;
+ if (nau8821_clock_check(nau8821, substream->stream,
+ nau8821->fs, osr)) {
+ return -EINVAL;
+ }
+ regmap_update_bits(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_ADC_SRC_MASK,
+ osr_adc_sel[osr].clk_src << NAU8821_CLK_ADC_SRC_SFT);
+ }
+
+ /* make BCLK and LRC divde configuration if the codec as master. */
+ regmap_read(nau8821->regmap, NAU8821_R1D_I2S_PCM_CTRL2, &ctrl_val);
+ if (ctrl_val & NAU8821_I2S_MS_MASTER) {
+ /* get the bclk and fs ratio */
+ bclk_fs = snd_soc_params_to_bclk(params) / nau8821->fs;
+ if (bclk_fs <= 32)
+ clk_div = 3;
+ else if (bclk_fs <= 64)
+ clk_div = 2;
+ else if (bclk_fs <= 128)
+ clk_div = 1;
+ else {
+ return -EINVAL;
+ }
+ regmap_update_bits(nau8821->regmap, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_LRC_DIV_MASK | NAU8821_I2S_BLK_DIV_MASK,
+ (clk_div << NAU8821_I2S_LRC_DIV_SFT) | clk_div);
+ }
+
+ switch (params_width(params)) {
+ case 16:
+ val_len |= NAU8821_I2S_DL_16;
+ break;
+ case 20:
+ val_len |= NAU8821_I2S_DL_20;
+ break;
+ case 24:
+ val_len |= NAU8821_I2S_DL_24;
+ break;
+ case 32:
+ val_len |= NAU8821_I2S_DL_32;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ regmap_update_bits(nau8821->regmap, NAU8821_R1C_I2S_PCM_CTRL1,
+ NAU8821_I2S_DL_MASK, val_len);
+
+ return 0;
+}
+
+static int nau8821_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt)
+{
+ struct snd_soc_component *component = codec_dai->component;
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ unsigned int ctrl1_val = 0, ctrl2_val = 0;
+
+ switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+ case SND_SOC_DAIFMT_CBP_CFP:
+ ctrl2_val |= NAU8821_I2S_MS_MASTER;
+ break;
+ case SND_SOC_DAIFMT_CBC_CFC:
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ case SND_SOC_DAIFMT_NB_NF:
+ break;
+ case SND_SOC_DAIFMT_IB_NF:
+ ctrl1_val |= NAU8821_I2S_BP_INV;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+ case SND_SOC_DAIFMT_I2S:
+ ctrl1_val |= NAU8821_I2S_DF_I2S;
+ break;
+ case SND_SOC_DAIFMT_LEFT_J:
+ ctrl1_val |= NAU8821_I2S_DF_LEFT;
+ break;
+ case SND_SOC_DAIFMT_RIGHT_J:
+ ctrl1_val |= NAU8821_I2S_DF_RIGTH;
+ break;
+ case SND_SOC_DAIFMT_DSP_A:
+ ctrl1_val |= NAU8821_I2S_DF_PCM_AB;
+ break;
+ case SND_SOC_DAIFMT_DSP_B:
+ ctrl1_val |= NAU8821_I2S_DF_PCM_AB;
+ ctrl1_val |= NAU8821_I2S_PCMB_EN;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ regmap_update_bits(nau8821->regmap, NAU8821_R1C_I2S_PCM_CTRL1,
+ NAU8821_I2S_DL_MASK | NAU8821_I2S_DF_MASK |
+ NAU8821_I2S_BP_MASK | NAU8821_I2S_PCMB_MASK, ctrl1_val);
+ regmap_update_bits(nau8821->regmap, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_MS_MASK, ctrl2_val);
+
+ return 0;
+}
+
+static int nau8821_digital_mute(struct snd_soc_dai *dai, int mute,
+ int direction)
+{
+ struct snd_soc_component *component = dai->component;
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ unsigned int val = 0;
+
+ if (mute)
+ val = NAU8821_DAC_SOFT_MUTE;
+
+ return regmap_update_bits(nau8821->regmap,
+ NAU8821_R31_MUTE_CTRL, NAU8821_DAC_SOFT_MUTE, val);
+}
+
+static const struct snd_soc_dai_ops nau8821_dai_ops = {
+ .hw_params = nau8821_hw_params,
+ .set_fmt = nau8821_set_dai_fmt,
+ .mute_stream = nau8821_digital_mute,
+};
+
+#define NAU8821_RATES SNDRV_PCM_RATE_8000_192000
+#define NAU8821_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE \
+ | SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S32_LE)
+
+static struct snd_soc_dai_driver nau8821_dai = {
+ .name = NUVOTON_CODEC_DAI,
+ .playback = {
+ .stream_name = "Playback",
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = NAU8821_RATES,
+ .formats = NAU8821_FORMATS,
+ },
+ .capture = {
+ .stream_name = "Capture",
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = NAU8821_RATES,
+ .formats = NAU8821_FORMATS,
+ },
+ .ops = &nau8821_dai_ops,
+};
+
+
+static bool nau8821_is_jack_inserted(struct regmap *regmap)
+{
+ bool active_high, is_high;
+ int status, jkdet;
+
+ regmap_read(regmap, NAU8821_R0D_JACK_DET_CTRL, &jkdet);
+ active_high = jkdet & NAU8821_JACK_POLARITY;
+ regmap_read(regmap, NAU8821_R82_GENERAL_STATUS, &status);
+ is_high = status & NAU8821_GPIO2_IN;
+ /* return jack connection status according to jack insertion logic
+ * active high or active low.
+ */
+ return active_high == is_high;
+}
+
+static void nau8821_int_status_clear_all(struct regmap *regmap)
+{
+ int active_irq, clear_irq, i;
+
+ /* Reset the intrruption status from rightmost bit if the corres-
+ * ponding irq event occurs.
+ */
+ regmap_read(regmap, NAU8821_R10_IRQ_STATUS, &active_irq);
+ for (i = 0; i < NAU8821_REG_DATA_LEN; i++) {
+ clear_irq = (0x1 << i);
+ if (active_irq & clear_irq)
+ regmap_write(regmap,
+ NAU8821_R11_INT_CLR_KEY_STATUS, clear_irq);
+ }
+}
+
+static void nau8821_eject_jack(struct nau8821 *nau8821)
+{
+ struct snd_soc_dapm_context *dapm = nau8821->dapm;
+ struct regmap *regmap = nau8821->regmap;
+ struct snd_soc_component *component = snd_soc_dapm_to_component(dapm);
+
+ /* Detach 2kOhm Resistors from MICBIAS to MICGND */
+ regmap_update_bits(regmap, NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_JKR2, 0);
+ /* HPL/HPR short to ground */
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_SPKR_DWN1R | NAU8821_SPKR_DWN1L, 0);
+ snd_soc_component_disable_pin(component, "MICBIAS");
+ snd_soc_dapm_sync(dapm);
+
+ /* Clear all interruption status */
+ nau8821_int_status_clear_all(regmap);
+
+ /* Enable the insertion interruption, disable the ejection inter-
+ * ruption, and then bypass de-bounce circuit.
+ */
+ regmap_update_bits(regmap, NAU8821_R12_INTERRUPT_DIS_CTRL,
+ NAU8821_IRQ_EJECT_DIS | NAU8821_IRQ_INSERT_DIS,
+ NAU8821_IRQ_EJECT_DIS);
+ /* Mask unneeded IRQs: 1 - disable, 0 - enable */
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_EJECT_EN | NAU8821_IRQ_INSERT_EN,
+ NAU8821_IRQ_EJECT_EN);
+
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_DET_DB_BYPASS, NAU8821_JACK_DET_DB_BYPASS);
+
+ /* Close clock for jack type detection at manual mode */
+ if (dapm->bias_level < SND_SOC_BIAS_PREPARE)
+ nau8821_configure_sysclk(nau8821, NAU8821_CLK_DIS, 0);
+
+ /* Recover to normal channel input */
+ regmap_update_bits(regmap, NAU8821_R2B_ADC_RATE,
+ NAU8821_ADC_R_SRC_EN, 0);
+}
+
+static void nau8821_jdet_work(struct work_struct *work)
+{
+ struct nau8821 *nau8821 =
+ container_of(work, struct nau8821, jdet_work);
+ struct snd_soc_dapm_context *dapm = nau8821->dapm;
+ struct snd_soc_component *component = snd_soc_dapm_to_component(dapm);
+ struct regmap *regmap = nau8821->regmap;
+ int jack_status_reg, mic_detected, event = 0, event_mask = 0;
+
+ snd_soc_component_force_enable_pin(component, "MICBIAS");
+ snd_soc_dapm_sync(dapm);
+ msleep(20);
+
+ regmap_read(regmap, NAU8821_R58_I2C_DEVICE_ID, &jack_status_reg);
+ mic_detected = !(jack_status_reg & NAU8821_KEYDET);
+ if (mic_detected) {
+ dev_dbg(nau8821->dev, "Headset connected\n");
+ event |= SND_JACK_HEADSET;
+
+ /* 2kOhm Resistor from MICBIAS to MICGND1 */
+ regmap_update_bits(regmap, NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_JKR2, NAU8821_MICBIAS_JKR2);
+ /* Latch Right Channel Analog data
+ * input into the Right Channel Filter
+ */
+ regmap_update_bits(regmap, NAU8821_R2B_ADC_RATE,
+ NAU8821_ADC_R_SRC_EN, NAU8821_ADC_R_SRC_EN);
+ } else {
+ dev_dbg(nau8821->dev, "Headphone connected\n");
+ event |= SND_JACK_HEADPHONE;
+ snd_soc_component_disable_pin(component, "MICBIAS");
+ snd_soc_dapm_sync(dapm);
+ }
+ event_mask |= SND_JACK_HEADSET;
+ snd_soc_jack_report(nau8821->jack, event, event_mask);
+}
+
+/* Enable interruptions with internal clock. */
+static void nau8821_setup_inserted_irq(struct nau8821 *nau8821)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ /* Enable internal VCO needed for interruptions */
+ if (nau8821->dapm->bias_level < SND_SOC_BIAS_PREPARE)
+ nau8821_configure_sysclk(nau8821, NAU8821_CLK_INTERNAL, 0);
+
+ /* Chip needs one FSCLK cycle in order to generate interruptions,
+ * as we cannot guarantee one will be provided by the system. Turning
+ * master mode on then off enables us to generate that FSCLK cycle
+ * with a minimum of contention on the clock bus.
+ */
+ regmap_update_bits(regmap, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_MS_MASK, NAU8821_I2S_MS_MASTER);
+ regmap_update_bits(regmap, NAU8821_R1D_I2S_PCM_CTRL2,
+ NAU8821_I2S_MS_MASK, NAU8821_I2S_MS_SLAVE);
+
+ /* Not bypass de-bounce circuit */
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_DET_DB_BYPASS, 0);
+
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_EJECT_EN, 0);
+ regmap_update_bits(regmap, NAU8821_R12_INTERRUPT_DIS_CTRL,
+ NAU8821_IRQ_EJECT_DIS, 0);
+}
+
+static irqreturn_t nau8821_interrupt(int irq, void *data)
+{
+ struct nau8821 *nau8821 = (struct nau8821 *)data;
+ struct regmap *regmap = nau8821->regmap;
+ int active_irq, clear_irq = 0, event = 0, event_mask = 0;
+
+ if (regmap_read(regmap, NAU8821_R10_IRQ_STATUS, &active_irq)) {
+ dev_err(nau8821->dev, "failed to read irq status\n");
+ return IRQ_NONE;
+ }
+
+ dev_dbg(nau8821->dev, "IRQ %d\n", active_irq);
+
+ if ((active_irq & NAU8821_JACK_EJECT_IRQ_MASK) ==
+ NAU8821_JACK_EJECT_DETECTED) {
+ regmap_update_bits(regmap, NAU8821_R71_ANALOG_ADC_1,
+ NAU8821_MICDET_MASK, NAU8821_MICDET_DIS);
+ nau8821_eject_jack(nau8821);
+ event_mask |= SND_JACK_HEADSET;
+ clear_irq = NAU8821_JACK_EJECT_IRQ_MASK;
+ } else if ((active_irq & NAU8821_JACK_INSERT_IRQ_MASK) ==
+ NAU8821_JACK_INSERT_DETECTED) {
+ regmap_update_bits(regmap, NAU8821_R71_ANALOG_ADC_1,
+ NAU8821_MICDET_MASK, NAU8821_MICDET_EN);
+ if (nau8821_is_jack_inserted(regmap)) {
+ /* detect microphone and jack type */
+ cancel_work_sync(&nau8821->jdet_work);
+ schedule_work(&nau8821->jdet_work);
+ /* Turn off insertion interruption at manual mode */
+ regmap_update_bits(regmap,
+ NAU8821_R12_INTERRUPT_DIS_CTRL,
+ NAU8821_IRQ_INSERT_DIS,
+ NAU8821_IRQ_INSERT_DIS);
+ regmap_update_bits(regmap,
+ NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_INSERT_EN,
+ NAU8821_IRQ_INSERT_EN);
+ nau8821_setup_inserted_irq(nau8821);
+ } else {
+ dev_warn(nau8821->dev,
+ "Inserted IRQ fired but not connected\n");
+ nau8821_eject_jack(nau8821);
+ }
+ }
+
+ if (!clear_irq)
+ clear_irq = active_irq;
+ /* clears the rightmost interruption */
+ regmap_write(regmap, NAU8821_R11_INT_CLR_KEY_STATUS, clear_irq);
+
+ if (event_mask)
+ snd_soc_jack_report(nau8821->jack, event, event_mask);
+
+ return IRQ_HANDLED;
+}
+
+static const struct regmap_config nau8821_regmap_config = {
+ .val_bits = NAU8821_REG_DATA_LEN,
+ .reg_bits = NAU8821_REG_ADDR_LEN,
+
+ .max_register = NAU8821_REG_MAX,
+ .readable_reg = nau8821_readable_reg,
+ .writeable_reg = nau8821_writeable_reg,
+ .volatile_reg = nau8821_volatile_reg,
+
+ .cache_type = REGCACHE_RBTREE,
+ .reg_defaults = nau8821_reg_defaults,
+ .num_reg_defaults = ARRAY_SIZE(nau8821_reg_defaults),
+};
+
+static int nau8821_component_probe(struct snd_soc_component *component)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ struct snd_soc_dapm_context *dapm =
+ snd_soc_component_get_dapm(component);
+
+ nau8821->dapm = dapm;
+
+ return 0;
+}
+
+/**
+ * nau8821_calc_fll_param - Calculate FLL parameters.
+ * @fll_in: external clock provided to codec.
+ * @fs: sampling rate.
+ * @fll_param: Pointer to structure of FLL parameters.
+ *
+ * Calculate FLL parameters to configure codec.
+ *
+ * Returns 0 for success or negative error code.
+ */
+static int nau8821_calc_fll_param(unsigned int fll_in,
+ unsigned int fs, struct nau8821_fll *fll_param)
+{
+ u64 fvco, fvco_max;
+ unsigned int fref, i, fvco_sel;
+
+ /* Ensure the reference clock frequency (FREF) is <= 13.5MHz by
+ * dividing freq_in by 1, 2, 4, or 8 using FLL pre-scalar.
+ * FREF = freq_in / NAU8821_FLL_REF_DIV_MASK
+ */
+ for (i = 0; i < ARRAY_SIZE(fll_pre_scalar); i++) {
+ fref = fll_in >> fll_pre_scalar[i].param;
+ if (fref <= NAU_FREF_MAX)
+ break;
+ }
+ if (i == ARRAY_SIZE(fll_pre_scalar))
+ return -EINVAL;
+ fll_param->clk_ref_div = fll_pre_scalar[i].val;
+
+ /* Choose the FLL ratio based on FREF */
+ for (i = 0; i < ARRAY_SIZE(fll_ratio); i++) {
+ if (fref >= fll_ratio[i].param)
+ break;
+ }
+ if (i == ARRAY_SIZE(fll_ratio))
+ return -EINVAL;
+ fll_param->ratio = fll_ratio[i].val;
+
+ /* Calculate the frequency of DCO (FDCO) given freq_out = 256 * Fs.
+ * FDCO must be within the 90MHz - 100MHz or the FFL cannot be
+ * guaranteed across the full range of operation.
+ * FDCO = freq_out * 2 * mclk_src_scaling
+ */
+ fvco_max = 0;
+ fvco_sel = ARRAY_SIZE(mclk_src_scaling);
+ for (i = 0; i < ARRAY_SIZE(mclk_src_scaling); i++) {
+ fvco = 256ULL * fs * 2 * mclk_src_scaling[i].param;
+ if (fvco > NAU_FVCO_MIN && fvco < NAU_FVCO_MAX &&
+ fvco_max < fvco) {
+ fvco_max = fvco;
+ fvco_sel = i;
+ }
+ }
+ if (ARRAY_SIZE(mclk_src_scaling) == fvco_sel)
+ return -EINVAL;
+ fll_param->mclk_src = mclk_src_scaling[fvco_sel].val;
+
+ /* Calculate the FLL 10-bit integer input and the FLL 24-bit fractional
+ * input based on FDCO, FREF and FLL ratio.
+ */
+ fvco = div_u64(fvco_max << 24, fref * fll_param->ratio);
+ fll_param->fll_int = (fvco >> 24) & 0x3ff;
+ fll_param->fll_frac = fvco & 0xffffff;
+
+ return 0;
+}
+
+static void nau8821_fll_apply(struct nau8821 *nau8821,
+ struct nau8821_fll *fll_param)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_SRC_MASK | NAU8821_CLK_MCLK_SRC_MASK,
+ NAU8821_CLK_SRC_MCLK | fll_param->mclk_src);
+ /* Make DSP operate at high speed for better performance. */
+ regmap_update_bits(regmap, NAU8821_R04_FLL1,
+ NAU8821_FLL_RATIO_MASK | NAU8821_ICTRL_LATCH_MASK,
+ fll_param->ratio | (0x6 << NAU8821_ICTRL_LATCH_SFT));
+ /* FLL 24-bit fractional input */
+ regmap_write(regmap, NAU8821_R0A_FLL7,
+ (fll_param->fll_frac >> 16) & 0xff);
+ regmap_write(regmap, NAU8821_R0B_FLL8, fll_param->fll_frac & 0xffff);
+ /* FLL 10-bit integer input */
+ regmap_update_bits(regmap, NAU8821_R06_FLL3,
+ NAU8821_FLL_INTEGER_MASK, fll_param->fll_int);
+ /* FLL pre-scaler */
+ regmap_update_bits(regmap, NAU8821_R07_FLL4,
+ NAU8821_HIGHBW_EN | NAU8821_FLL_REF_DIV_MASK,
+ NAU8821_HIGHBW_EN |
+ (fll_param->clk_ref_div << NAU8821_FLL_REF_DIV_SFT));
+ /* select divided VCO input */
+ regmap_update_bits(regmap, NAU8821_R08_FLL5,
+ NAU8821_FLL_CLK_SW_MASK, NAU8821_FLL_CLK_SW_REF);
+ /* Disable free-running mode */
+ regmap_update_bits(regmap,
+ NAU8821_R09_FLL6, NAU8821_DCO_EN, 0);
+ if (fll_param->fll_frac) {
+ /* set FLL loop filter enable and cutoff frequency at 500Khz */
+ regmap_update_bits(regmap, NAU8821_R08_FLL5,
+ NAU8821_FLL_PDB_DAC_EN | NAU8821_FLL_LOOP_FTR_EN |
+ NAU8821_FLL_FTR_SW_MASK,
+ NAU8821_FLL_PDB_DAC_EN | NAU8821_FLL_LOOP_FTR_EN |
+ NAU8821_FLL_FTR_SW_FILTER);
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_SDM_EN | NAU8821_CUTOFF500,
+ NAU8821_SDM_EN | NAU8821_CUTOFF500);
+ } else {
+ /* disable FLL loop filter and cutoff frequency */
+ regmap_update_bits(regmap, NAU8821_R08_FLL5,
+ NAU8821_FLL_PDB_DAC_EN | NAU8821_FLL_LOOP_FTR_EN |
+ NAU8821_FLL_FTR_SW_MASK, NAU8821_FLL_FTR_SW_ACCU);
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_SDM_EN | NAU8821_CUTOFF500, 0);
+ }
+}
+
+/**
+ * nau8821_set_fll - FLL configuration of nau8821
+ * @codec: codec component
+ * @freq_in: frequency of input clock source
+ * @freq_out: must be 256*Fs in order to achieve the best performance
+ *
+ * The FLL function can select BCLK or MCLK as the input clock source.
+ *
+ * Returns 0 if the parameters have been applied successfully
+ * or negative error code.
+ */
+static int nau8821_set_fll(struct snd_soc_component *component,
+ int pll_id, int source, unsigned int freq_in, unsigned int freq_out)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ struct nau8821_fll fll_set_param, *fll_param = &fll_set_param;
+ int ret, fs;
+
+ fs = freq_out >> 8;
+ ret = nau8821_calc_fll_param(freq_in, fs, fll_param);
+ if (ret) {
+ dev_err(nau8821->dev,
+ "Unsupported input clock %d to output clock %d\n",
+ freq_in, freq_out);
+ return ret;
+ }
+ dev_dbg(nau8821->dev,
+ "mclk_src=%x ratio=%x fll_frac=%x fll_int=%x clk_ref_div=%x\n",
+ fll_param->mclk_src, fll_param->ratio, fll_param->fll_frac,
+ fll_param->fll_int, fll_param->clk_ref_div);
+
+ nau8821_fll_apply(nau8821, fll_param);
+ mdelay(2);
+ regmap_update_bits(nau8821->regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_SRC_MASK, NAU8821_CLK_SRC_VCO);
+
+ return 0;
+}
+
+static void nau8821_configure_mclk_as_sysclk(struct regmap *regmap)
+{
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_SRC_MASK, NAU8821_CLK_SRC_MCLK);
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_DCO_EN, 0);
+ /* Make DSP operate as default setting for power saving. */
+ regmap_update_bits(regmap, NAU8821_R04_FLL1,
+ NAU8821_ICTRL_LATCH_MASK, 0);
+}
+
+static int nau8821_configure_sysclk(struct nau8821 *nau8821,
+ int clk_id, unsigned int freq)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ switch (clk_id) {
+ case NAU8821_CLK_DIS:
+ /* Clock provided externally and disable internal VCO clock */
+ nau8821_configure_mclk_as_sysclk(regmap);
+ break;
+ case NAU8821_CLK_MCLK:
+ nau8821_configure_mclk_as_sysclk(regmap);
+ /* MCLK not changed by clock tree */
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_MCLK_SRC_MASK, 0);
+ break;
+ case NAU8821_CLK_INTERNAL:
+ if (nau8821_is_jack_inserted(regmap)) {
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_DCO_EN, NAU8821_DCO_EN);
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_SRC_MASK, NAU8821_CLK_SRC_VCO);
+ /* Decrease the VCO frequency and make DSP operate
+ * as default setting for power saving.
+ */
+ regmap_update_bits(regmap, NAU8821_R03_CLK_DIVIDER,
+ NAU8821_CLK_MCLK_SRC_MASK, 0xf);
+ regmap_update_bits(regmap, NAU8821_R04_FLL1,
+ NAU8821_ICTRL_LATCH_MASK |
+ NAU8821_FLL_RATIO_MASK, 0x10);
+ regmap_update_bits(regmap, NAU8821_R09_FLL6,
+ NAU8821_SDM_EN, NAU8821_SDM_EN);
+ }
+ break;
+ case NAU8821_CLK_FLL_MCLK:
+ /* Higher FLL reference input frequency can only set lower
+ * gain error, such as 0000 for input reference from MCLK
+ * 12.288Mhz.
+ */
+ regmap_update_bits(regmap, NAU8821_R06_FLL3,
+ NAU8821_FLL_CLK_SRC_MASK | NAU8821_GAIN_ERR_MASK,
+ NAU8821_FLL_CLK_SRC_MCLK | 0);
+ break;
+ case NAU8821_CLK_FLL_BLK:
+ /* If FLL reference input is from low frequency source,
+ * higher error gain can apply such as 0xf which has
+ * the most sensitive gain error correction threshold,
+ * Therefore, FLL has the most accurate DCO to
+ * target frequency.
+ */
+ regmap_update_bits(regmap, NAU8821_R06_FLL3,
+ NAU8821_FLL_CLK_SRC_MASK | NAU8821_GAIN_ERR_MASK,
+ NAU8821_FLL_CLK_SRC_BLK |
+ (0xf << NAU8821_GAIN_ERR_SFT));
+ break;
+ case NAU8821_CLK_FLL_FS:
+ /* If FLL reference input is from low frequency source,
+ * higher error gain can apply such as 0xf which has
+ * the most sensitive gain error correction threshold,
+ * Therefore, FLL has the most accurate DCO to
+ * target frequency.
+ */
+ regmap_update_bits(regmap, NAU8821_R06_FLL3,
+ NAU8821_FLL_CLK_SRC_MASK | NAU8821_GAIN_ERR_MASK,
+ NAU8821_FLL_CLK_SRC_FS |
+ (0xf << NAU8821_GAIN_ERR_SFT));
+ break;
+ default:
+ dev_err(nau8821->dev, "Invalid clock id (%d)\n", clk_id);
+ return -EINVAL;
+ }
+ nau8821->clk_id = clk_id;
+ dev_dbg(nau8821->dev, "Sysclk is %dHz and clock id is %d\n", freq,
+ nau8821->clk_id);
+
+ return 0;
+}
+
+static int nau8821_set_sysclk(struct snd_soc_component *component, int clk_id,
+ int source, unsigned int freq, int dir)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ return nau8821_configure_sysclk(nau8821, clk_id, freq);
+}
+
+static int nau8821_resume_setup(struct nau8821 *nau8821)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ /* Close clock when jack type detection at manual mode */
+ nau8821_configure_sysclk(nau8821, NAU8821_CLK_DIS, 0);
+ if (nau8821->irq) {
+ /* Clear all interruption status */
+ nau8821_int_status_clear_all(regmap);
+
+ /* Enable both insertion and ejection interruptions, and then
+ * bypass de-bounce circuit.
+ */
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_EJECT_EN | NAU8821_IRQ_INSERT_EN, 0);
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_DET_DB_BYPASS,
+ NAU8821_JACK_DET_DB_BYPASS);
+ regmap_update_bits(regmap, NAU8821_R12_INTERRUPT_DIS_CTRL,
+ NAU8821_IRQ_INSERT_DIS | NAU8821_IRQ_EJECT_DIS, 0);
+ }
+
+ return 0;
+}
+
+static int nau8821_set_bias_level(struct snd_soc_component *component,
+ enum snd_soc_bias_level level)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ struct regmap *regmap = nau8821->regmap;
+
+ switch (level) {
+ case SND_SOC_BIAS_ON:
+ break;
+
+ case SND_SOC_BIAS_PREPARE:
+ break;
+
+ case SND_SOC_BIAS_STANDBY:
+ /* Setup codec configuration after resume */
+ if (snd_soc_component_get_bias_level(component) ==
+ SND_SOC_BIAS_OFF)
+ nau8821_resume_setup(nau8821);
+ break;
+
+ case SND_SOC_BIAS_OFF:
+ /* HPL/HPR short to ground */
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_SPKR_DWN1R | NAU8821_SPKR_DWN1L, 0);
+ if (nau8821->irq) {
+ /* Reset the configuration of jack type for detection.
+ * Detach 2kOhm Resistors from MICBIAS to MICGND1/2.
+ */
+ regmap_update_bits(regmap, NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_JKR2, 0);
+ /* Turn off all interruptions before system shutdown.
+ * Keep theinterruption quiet before resume
+ * setup completes.
+ */
+ regmap_write(regmap,
+ NAU8821_R12_INTERRUPT_DIS_CTRL, 0xffff);
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_EJECT_EN | NAU8821_IRQ_INSERT_EN,
+ NAU8821_IRQ_EJECT_EN | NAU8821_IRQ_INSERT_EN);
+ }
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+static int __maybe_unused nau8821_suspend(struct snd_soc_component *component)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ if (nau8821->irq)
+ disable_irq(nau8821->irq);
+ snd_soc_component_force_bias_level(component, SND_SOC_BIAS_OFF);
+ /* Power down codec power; don't support button wakeup */
+ snd_soc_component_disable_pin(component, "MICBIAS");
+ snd_soc_dapm_sync(nau8821->dapm);
+ regcache_cache_only(nau8821->regmap, true);
+ regcache_mark_dirty(nau8821->regmap);
+
+ return 0;
+}
+
+static int __maybe_unused nau8821_resume(struct snd_soc_component *component)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+
+ regcache_cache_only(nau8821->regmap, false);
+ regcache_sync(nau8821->regmap);
+ if (nau8821->irq)
+ enable_irq(nau8821->irq);
+
+ return 0;
+}
+
+static const struct snd_soc_component_driver nau8821_component_driver = {
+ .probe = nau8821_component_probe,
+ .set_sysclk = nau8821_set_sysclk,
+ .set_pll = nau8821_set_fll,
+ .set_bias_level = nau8821_set_bias_level,
+ .suspend = nau8821_suspend,
+ .resume = nau8821_resume,
+ .controls = nau8821_controls,
+ .num_controls = ARRAY_SIZE(nau8821_controls),
+ .dapm_widgets = nau8821_dapm_widgets,
+ .num_dapm_widgets = ARRAY_SIZE(nau8821_dapm_widgets),
+ .dapm_routes = nau8821_dapm_routes,
+ .num_dapm_routes = ARRAY_SIZE(nau8821_dapm_routes),
+ .suspend_bias_off = 1,
+ .non_legacy_dai_naming = 1,
+ .idle_bias_on = 1,
+ .use_pmdown_time = 1,
+ .endianness = 1,
+};
+
+/**
+ * nau8821_enable_jack_detect - Specify a jack for event reporting
+ *
+ * @component: component to register the jack with
+ * @jack: jack to use to report headset and button events on
+ *
+ * After this function has been called the headset insert/remove and button
+ * events will be routed to the given jack. Jack can be null to stop
+ * reporting.
+ */
+int nau8821_enable_jack_detect(struct snd_soc_component *component,
+ struct snd_soc_jack *jack)
+{
+ struct nau8821 *nau8821 = snd_soc_component_get_drvdata(component);
+ int ret;
+
+ nau8821->jack = jack;
+ /* Initiate jack detection work queue */
+ INIT_WORK(&nau8821->jdet_work, nau8821_jdet_work);
+ ret = devm_request_threaded_irq(nau8821->dev, nau8821->irq, NULL,
+ nau8821_interrupt, IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ "nau8821", nau8821);
+ if (ret) {
+ dev_err(nau8821->dev, "Cannot request irq %d (%d)\n",
+ nau8821->irq, ret);
+ return ret;
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(nau8821_enable_jack_detect);
+
+static void nau8821_reset_chip(struct regmap *regmap)
+{
+ regmap_write(regmap, NAU8821_R00_RESET, 0xffff);
+ regmap_write(regmap, NAU8821_R00_RESET, 0xffff);
+}
+
+static void nau8821_print_device_properties(struct nau8821 *nau8821)
+{
+ struct device *dev = nau8821->dev;
+
+ dev_dbg(dev, "jkdet-enable: %d\n", nau8821->jkdet_enable);
+ dev_dbg(dev, "jkdet-pull-enable: %d\n", nau8821->jkdet_pull_enable);
+ dev_dbg(dev, "jkdet-pull-up: %d\n", nau8821->jkdet_pull_up);
+ dev_dbg(dev, "jkdet-polarity: %d\n", nau8821->jkdet_polarity);
+ dev_dbg(dev, "micbias-voltage: %d\n", nau8821->micbias_voltage);
+ dev_dbg(dev, "vref-impedance: %d\n", nau8821->vref_impedance);
+ dev_dbg(dev, "jack-insert-debounce: %d\n",
+ nau8821->jack_insert_debounce);
+ dev_dbg(dev, "jack-eject-debounce: %d\n",
+ nau8821->jack_eject_debounce);
+ dev_dbg(dev, "dmic-clk-threshold: %d\n",
+ nau8821->dmic_clk_threshold);
+}
+
+static int nau8821_read_device_properties(struct device *dev,
+ struct nau8821 *nau8821)
+{
+ int ret;
+
+ nau8821->jkdet_enable = device_property_read_bool(dev,
+ "nuvoton,jkdet-enable");
+ nau8821->jkdet_pull_enable = device_property_read_bool(dev,
+ "nuvoton,jkdet-pull-enable");
+ nau8821->jkdet_pull_up = device_property_read_bool(dev,
+ "nuvoton,jkdet-pull-up");
+ ret = device_property_read_u32(dev, "nuvoton,jkdet-polarity",
+ &nau8821->jkdet_polarity);
+ if (ret)
+ nau8821->jkdet_polarity = 1;
+ ret = device_property_read_u32(dev, "nuvoton,micbias-voltage",
+ &nau8821->micbias_voltage);
+ if (ret)
+ nau8821->micbias_voltage = 6;
+ ret = device_property_read_u32(dev, "nuvoton,vref-impedance",
+ &nau8821->vref_impedance);
+ if (ret)
+ nau8821->vref_impedance = 2;
+ ret = device_property_read_u32(dev, "nuvoton,jack-insert-debounce",
+ &nau8821->jack_insert_debounce);
+ if (ret)
+ nau8821->jack_insert_debounce = 7;
+ ret = device_property_read_u32(dev, "nuvoton,jack-eject-debounce",
+ &nau8821->jack_eject_debounce);
+ if (ret)
+ nau8821->jack_eject_debounce = 0;
+ ret = device_property_read_u32(dev, "nuvoton,dmic-clk-threshold",
+ &nau8821->dmic_clk_threshold);
+ if (ret)
+ nau8821->dmic_clk_threshold = 3072000;
+
+ return 0;
+}
+
+static void nau8821_init_regs(struct nau8821 *nau8821)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ /* Enable Bias/Vmid */
+ regmap_update_bits(regmap, NAU8821_R66_BIAS_ADJ,
+ NAU8821_BIAS_VMID, NAU8821_BIAS_VMID);
+ regmap_update_bits(regmap, NAU8821_R76_BOOST,
+ NAU8821_GLOBAL_BIAS_EN, NAU8821_GLOBAL_BIAS_EN);
+ /* VMID Tieoff setting and enable TESTDAC.
+ * This sets the analog DAC inputs to a '0' input signal to avoid
+ * any glitches due to power up transients in both the analog and
+ * digital DAC circuit.
+ */
+ regmap_update_bits(regmap, NAU8821_R66_BIAS_ADJ,
+ NAU8821_BIAS_VMID_SEL_MASK | NAU8821_BIAS_TESTDAC_EN,
+ (nau8821->vref_impedance << NAU8821_BIAS_VMID_SEL_SFT) |
+ NAU8821_BIAS_TESTDAC_EN);
+ /* Disable short Frame Sync detection logic */
+ regmap_update_bits(regmap, NAU8821_R1E_LEFT_TIME_SLOT,
+ NAU8821_DIS_FS_SHORT_DET, NAU8821_DIS_FS_SHORT_DET);
+ /* Disable Boost Driver, Automatic Short circuit protection enable */
+ regmap_update_bits(regmap, NAU8821_R76_BOOST,
+ NAU8821_PRECHARGE_DIS | NAU8821_HP_BOOST_DIS |
+ NAU8821_HP_BOOST_G_DIS | NAU8821_SHORT_SHUTDOWN_EN,
+ NAU8821_PRECHARGE_DIS | NAU8821_HP_BOOST_DIS |
+ NAU8821_HP_BOOST_G_DIS | NAU8821_SHORT_SHUTDOWN_EN);
+ /* Class G timer 64ms */
+ regmap_update_bits(regmap, NAU8821_R4B_CLASSG_CTRL,
+ NAU8821_CLASSG_TIMER_MASK,
+ 0x20 << NAU8821_CLASSG_TIMER_SFT);
+ /* Class AB bias current to 2x, DAC Capacitor enable MSB/LSB */
+ regmap_update_bits(regmap, NAU8821_R6A_ANALOG_CONTROL_2,
+ NAU8821_HP_NON_CLASSG_CURRENT_2xADJ |
+ NAU8821_DAC_CAPACITOR_MSB | NAU8821_DAC_CAPACITOR_LSB,
+ NAU8821_HP_NON_CLASSG_CURRENT_2xADJ |
+ NAU8821_DAC_CAPACITOR_MSB | NAU8821_DAC_CAPACITOR_LSB);
+ /* Disable DACR/L power */
+ regmap_update_bits(regmap, NAU8821_R80_CHARGE_PUMP,
+ NAU8821_POWER_DOWN_DACR | NAU8821_POWER_DOWN_DACL, 0);
+ /* DAC clock delay 2ns, VREF */
+ regmap_update_bits(regmap, NAU8821_R73_RDAC,
+ NAU8821_DAC_CLK_DELAY_MASK | NAU8821_DAC_VREF_MASK,
+ (0x2 << NAU8821_DAC_CLK_DELAY_SFT) |
+ (0x3 << NAU8821_DAC_VREF_SFT));
+
+ regmap_update_bits(regmap, NAU8821_R74_MIC_BIAS,
+ NAU8821_MICBIAS_VOLTAGE_MASK, nau8821->micbias_voltage);
+ /* Default oversampling/decimations settings are unusable
+ * (audible hiss). Set it to something better.
+ */
+ regmap_update_bits(regmap, NAU8821_R2B_ADC_RATE,
+ NAU8821_ADC_SYNC_DOWN_MASK, NAU8821_ADC_SYNC_DOWN_64);
+ regmap_update_bits(regmap, NAU8821_R2C_DAC_CTRL1,
+ NAU8821_DAC_OVERSAMPLE_MASK, NAU8821_DAC_OVERSAMPLE_64);
+}
+
+static int nau8821_setup_irq(struct nau8821 *nau8821)
+{
+ struct regmap *regmap = nau8821->regmap;
+
+ /* Jack detection */
+ regmap_update_bits(regmap, NAU8821_R1A_GPIO12_CTRL,
+ NAU8821_JKDET_OUTPUT_EN,
+ nau8821->jkdet_enable ? 0 : NAU8821_JKDET_OUTPUT_EN);
+ regmap_update_bits(regmap, NAU8821_R1A_GPIO12_CTRL,
+ NAU8821_JKDET_PULL_EN,
+ nau8821->jkdet_pull_enable ? 0 : NAU8821_JKDET_PULL_EN);
+ regmap_update_bits(regmap, NAU8821_R1A_GPIO12_CTRL,
+ NAU8821_JKDET_PULL_UP,
+ nau8821->jkdet_pull_up ? NAU8821_JKDET_PULL_UP : 0);
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_POLARITY,
+ /* jkdet_polarity - 1 is for active-low */
+ nau8821->jkdet_polarity ? 0 : NAU8821_JACK_POLARITY);
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_INSERT_DEBOUNCE_MASK,
+ nau8821->jack_insert_debounce <<
+ NAU8821_JACK_INSERT_DEBOUNCE_SFT);
+ regmap_update_bits(regmap, NAU8821_R0D_JACK_DET_CTRL,
+ NAU8821_JACK_EJECT_DEBOUNCE_MASK,
+ nau8821->jack_eject_debounce <<
+ NAU8821_JACK_EJECT_DEBOUNCE_SFT);
+ /* Pull up IRQ pin */
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK,
+ NAU8821_IRQ_PIN_PULL_UP | NAU8821_IRQ_PIN_PULL_EN |
+ NAU8821_IRQ_OUTPUT_EN, NAU8821_IRQ_PIN_PULL_UP |
+ NAU8821_IRQ_PIN_PULL_EN | NAU8821_IRQ_OUTPUT_EN);
+ /* Disable interruption before codec initiation done */
+ /* Mask unneeded IRQs: 1 - disable, 0 - enable */
+ regmap_update_bits(regmap, NAU8821_R0F_INTERRUPT_MASK, 0x3f5, 0x3f5);
+
+ return 0;
+}
+
+static int nau8821_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &i2c->dev;
+ struct nau8821 *nau8821 = dev_get_platdata(&i2c->dev);
+ int ret, value;
+
+ if (!nau8821) {
+ nau8821 = devm_kzalloc(dev, sizeof(*nau8821), GFP_KERNEL);
+ if (!nau8821)
+ return -ENOMEM;
+ nau8821_read_device_properties(dev, nau8821);
+ }
+ i2c_set_clientdata(i2c, nau8821);
+
+ nau8821->regmap = devm_regmap_init_i2c(i2c, &nau8821_regmap_config);
+ if (IS_ERR(nau8821->regmap))
+ return PTR_ERR(nau8821->regmap);
+
+ nau8821->dev = dev;
+ nau8821->irq = i2c->irq;
+ nau8821_print_device_properties(nau8821);
+
+ nau8821_reset_chip(nau8821->regmap);
+ ret = regmap_read(nau8821->regmap, NAU8821_R58_I2C_DEVICE_ID, &value);
+ if (ret) {
+ dev_err(dev, "Failed to read device id (%d)\n", ret);
+ return ret;
+ }
+ nau8821_init_regs(nau8821);
+
+ if (i2c->irq)
+ nau8821_setup_irq(nau8821);
+
+ ret = devm_snd_soc_register_component(&i2c->dev,
+ &nau8821_component_driver, &nau8821_dai, 1);
+
+ return ret;
+}
+
+static int nau8821_i2c_remove(struct i2c_client *i2c_client)
+{
+ struct nau8821 *nau8821 = i2c_get_clientdata(i2c_client);
+
+ devm_free_irq(nau8821->dev, nau8821->irq, nau8821);
+
+ return 0;
+}
+
+static const struct i2c_device_id nau8821_i2c_ids[] = {
+ { "nau8821", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, nau8821_i2c_ids);
+
+#ifdef CONFIG_OF
+static const struct of_device_id nau8821_of_ids[] = {
+ { .compatible = "nuvoton,nau8821", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, nau8821_of_ids);
+#endif
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id nau8821_acpi_match[] = {
+ { "NVTN2020", 0 },
+ {},
+};
+MODULE_DEVICE_TABLE(acpi, nau8821_acpi_match);
+#endif
+
+static struct i2c_driver nau8821_driver = {
+ .driver = {
+ .name = "nau8821",
+ .of_match_table = of_match_ptr(nau8821_of_ids),
+ .acpi_match_table = ACPI_PTR(nau8821_acpi_match),
+ },
+ .probe = nau8821_i2c_probe,
+ .remove = nau8821_i2c_remove,
+ .id_table = nau8821_i2c_ids,
+};
+module_i2c_driver(nau8821_driver);
+
+MODULE_DESCRIPTION("ASoC nau8821 driver");
+MODULE_AUTHOR("John Hsu <kchsu0@nuvoton.com>");
+MODULE_AUTHOR("Seven Lee <wtli@nuvoton.com>");
+MODULE_LICENSE("GPL");
diff --git a/sound/soc/codecs/nau8821.h b/sound/soc/codecs/nau8821.h
new file mode 100644
index 000000000000..a92edfeb9d3a
--- /dev/null
+++ b/sound/soc/codecs/nau8821.h
@@ -0,0 +1,533 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * NAU88L21 ALSA SoC audio driver
+ *
+ * Copyright 2021 Nuvoton Technology Corp.
+ * Author: John Hsu <kchsu0@nuvoton.com>
+ * Co-author: Seven Lee <wtli@nuvoton.com>
+ */
+
+#ifndef __NAU8821_H__
+#define __NAU8821_H__
+
+#define NAU8821_R00_RESET 0x00
+#define NAU8821_R01_ENA_CTRL 0x01
+#define NAU8821_R03_CLK_DIVIDER 0x03
+#define NAU8821_R04_FLL1 0x04
+#define NAU8821_R05_FLL2 0x05
+#define NAU8821_R06_FLL3 0x06
+#define NAU8821_R07_FLL4 0x07
+#define NAU8821_R08_FLL5 0x08
+#define NAU8821_R09_FLL6 0x09
+#define NAU8821_R0A_FLL7 0x0a
+#define NAU8821_R0B_FLL8 0x0b
+#define NAU8821_R0D_JACK_DET_CTRL 0x0d
+#define NAU8821_R0F_INTERRUPT_MASK 0x0f
+#define NAU8821_R10_IRQ_STATUS 0x10
+#define NAU8821_R11_INT_CLR_KEY_STATUS 0x11
+#define NAU8821_R12_INTERRUPT_DIS_CTRL 0x12
+#define NAU8821_R13_DMIC_CTRL 0x13
+#define NAU8821_R1A_GPIO12_CTRL 0x1a
+#define NAU8821_R1B_TDM_CTRL 0x1b
+#define NAU8821_R1C_I2S_PCM_CTRL1 0x1c
+#define NAU8821_R1D_I2S_PCM_CTRL2 0x1d
+#define NAU8821_R1E_LEFT_TIME_SLOT 0x1e
+#define NAU8821_R1F_RIGHT_TIME_SLOT 0x1f
+#define NAU8821_R21_BIQ0_COF1 0x21
+#define NAU8821_R22_BIQ0_COF2 0x22
+#define NAU8821_R23_BIQ0_COF3 0x23
+#define NAU8821_R24_BIQ0_COF4 0x24
+#define NAU8821_R25_BIQ0_COF5 0x25
+#define NAU8821_R26_BIQ0_COF6 0x26
+#define NAU8821_R27_BIQ0_COF7 0x27
+#define NAU8821_R28_BIQ0_COF8 0x28
+#define NAU8821_R29_BIQ0_COF9 0x29
+#define NAU8821_R2A_BIQ0_COF10 0x2a
+#define NAU8821_R2B_ADC_RATE 0x2b
+#define NAU8821_R2C_DAC_CTRL1 0x2c
+#define NAU8821_R2D_DAC_CTRL2 0x2d
+#define NAU8821_R2F_DAC_DGAIN_CTRL 0x2f
+#define NAU8821_R30_ADC_DGAIN_CTRL 0x30
+#define NAU8821_R31_MUTE_CTRL 0x31
+#define NAU8821_R32_HSVOL_CTRL 0x32
+#define NAU8821_R34_DACR_CTRL 0x34
+#define NAU8821_R35_ADC_DGAIN_CTRL1 0x35
+#define NAU8821_R36_ADC_DRC_KNEE_IP12 0x36
+#define NAU8821_R37_ADC_DRC_KNEE_IP34 0x37
+#define NAU8821_R38_ADC_DRC_SLOPES 0x38
+#define NAU8821_R39_ADC_DRC_ATKDCY 0x39
+#define NAU8821_R3A_DAC_DRC_KNEE_IP12 0x3a
+#define NAU8821_R3B_DAC_DRC_KNEE_IP34 0x3b
+#define NAU8821_R3C_DAC_DRC_SLOPES 0x3c
+#define NAU8821_R3D_DAC_DRC_ATKDCY 0x3d
+#define NAU8821_R41_BIQ1_COF1 0x41
+#define NAU8821_R42_BIQ1_COF2 0x42
+#define NAU8821_R43_BIQ1_COF3 0x43
+#define NAU8821_R44_BIQ1_COF4 0x44
+#define NAU8821_R45_BIQ1_COF5 0x45
+#define NAU8821_R46_BIQ1_COF6 0x46
+#define NAU8821_R47_BIQ1_COF7 0x47
+#define NAU8821_R48_BIQ1_COF8 0x48
+#define NAU8821_R49_BIQ1_COF9 0x49
+#define NAU8821_R4A_BIQ1_COF10 0x4a
+#define NAU8821_R4B_CLASSG_CTRL 0x4b
+#define NAU8821_R4C_IMM_MODE_CTRL 0x4c
+#define NAU8821_R4D_IMM_RMS_L 0x4d
+#define NAU8821_R4E_FUSE_CTRL2 0x4e
+#define NAU8821_R4F_FUSE_CTRL3 0x4f
+#define NAU8821_R51_FUSE_CTRL1 0x51
+#define NAU8821_R53_OTPDOUT_1 0x53
+#define NAU8821_R54_OTPDOUT_2 0x54
+#define NAU8821_R55_MISC_CTRL 0x55
+#define NAU8821_R58_I2C_DEVICE_ID 0x58
+#define NAU8821_R59_SARDOUT_RAM_STATUS 0x59
+#define NAU8821_R5A_SOFTWARE_RST 0x5a
+#define NAU8821_R66_BIAS_ADJ 0x66
+#define NAU8821_R68_TRIM_SETTINGS 0x68
+#define NAU8821_R69_ANALOG_CONTROL_1 0x69
+#define NAU8821_R6A_ANALOG_CONTROL_2 0x6a
+#define NAU8821_R6B_PGA_MUTE 0x6b
+#define NAU8821_R71_ANALOG_ADC_1 0x71
+#define NAU8821_R72_ANALOG_ADC_2 0x72
+#define NAU8821_R73_RDAC 0x73
+#define NAU8821_R74_MIC_BIAS 0x74
+#define NAU8821_R76_BOOST 0x76
+#define NAU8821_R77_FEPGA 0x77
+#define NAU8821_R7E_PGA_GAIN 0x7e
+#define NAU8821_R7F_POWER_UP_CONTROL 0x7f
+#define NAU8821_R80_CHARGE_PUMP 0x80
+#define NAU8821_R81_CHARGE_PUMP_INPUT_READ 0x81
+#define NAU8821_R82_GENERAL_STATUS 0x82
+#define NAU8821_REG_MAX NAU8821_R82_GENERAL_STATUS
+/* 16-bit control register address, and 16-bits control register data */
+#define NAU8821_REG_ADDR_LEN 16
+#define NAU8821_REG_DATA_LEN 16
+
+/* ENA_CTRL (0x01) */
+#define NAU8821_CLK_DAC_INV_SFT 14
+#define NAU8821_CLK_DAC_INV (0x1 << NAU8821_CLK_DAC_INV)
+#define NAU8821_EN_DACR_SFT 11
+#define NAU8821_EN_DACR (0x1 << NAU8821_EN_DACR_SFT)
+#define NAU8821_EN_DACL_SFT 10
+#define NAU8821_EN_DACL (0x1 << NAU8821_EN_DACL_SFT)
+#define NAU8821_EN_ADCR_SFT 9
+#define NAU8821_EN_ADCR (0x1 << NAU8821_EN_ADCR_SFT)
+#define NAU8821_EN_ADCL_SFT 8
+#define NAU8821_EN_ADCL (0x1 << NAU8821_EN_ADCL_SFT)
+#define NAU8821_EN_ADC_CLK_SFT 7
+#define NAU8821_EN_ADC_CLK (0x1 << NAU8821_EN_ADC_CLK_SFT)
+#define NAU8821_EN_DAC_CLK_SFT 6
+#define NAU8821_EN_DAC_CLK (0x1 << NAU8821_EN_DAC_CLK_SFT)
+#define NAU8821_EN_I2S_CLK_SFT 4
+#define NAU8821_EN_I2S_CLK (0x1 << NAU8821_EN_I2S_CLK_SFT)
+#define NAU8821_EN_DRC_CLK_SFT 0
+#define NAU8821_EN_DRC_CLK (0x1 << NAU8821_EN_DRC_CLK_SFT)
+
+/* CLK_DIVIDER (0x03) */
+#define NAU8821_CLK_SRC_SFT 15
+#define NAU8821_CLK_SRC_MASK (0x1 << NAU8821_CLK_SRC_SFT)
+#define NAU8821_CLK_SRC_VCO (0x1 << NAU8821_CLK_SRC_SFT)
+#define NAU8821_CLK_SRC_MCLK (0x0 << NAU8821_CLK_SRC_SFT)
+#define NAU8821_CLK_CODEC_SRC_SFT 13
+#define NAU8821_CLK_CODEC_SRC_MASK (0x1 << NAU8821_CLK_CODEC_SRC_SFT)
+#define NAU8821_CLK_CODEC_SRC_VCO (0x1 << NAU8821_CLK_CODEC_SRC_SFT)
+#define NAU8821_CLK_CODEC_SRC_MCLK (0x0 << NAU8821_CLK_CODEC_SRC_SFT)
+#define NAU8821_CLK_ADC_SRC_SFT 6
+#define NAU8821_CLK_ADC_SRC_MASK (0x3 << NAU8821_CLK_ADC_SRC_SFT)
+#define NAU8821_CLK_DAC_SRC_SFT 4
+#define NAU8821_CLK_DAC_SRC_MASK (0x3 << NAU8821_CLK_DAC_SRC_SFT)
+#define NAU8821_CLK_MCLK_SRC_MASK 0xf
+
+/* FLL1 (0x04) */
+#define NAU8821_ICTRL_LATCH_SFT 10
+#define NAU8821_ICTRL_LATCH_MASK (0x7 << NAU8821_ICTRL_LATCH_SFT)
+#define NAU8821_FLL_RATIO_MASK 0x7f
+
+/* FLL3 (0x06) */
+#define NAU8821_GAIN_ERR_SFT 12
+#define NAU8821_GAIN_ERR_MASK (0xf << NAU8821_GAIN_ERR_SFT)
+#define NAU8821_FLL_CLK_SRC_SFT 10
+#define NAU8821_FLL_CLK_SRC_MASK (0x3 << NAU8821_FLL_CLK_SRC_SFT)
+#define NAU8821_FLL_CLK_SRC_FS (0x3 << NAU8821_FLL_CLK_SRC_SFT)
+#define NAU8821_FLL_CLK_SRC_BLK (0x2 << NAU8821_FLL_CLK_SRC_SFT)
+#define NAU8821_FLL_CLK_SRC_MCLK (0x0 << NAU8821_FLL_CLK_SRC_SFT)
+#define NAU8821_FLL_INTEGER_MASK 0x3ff
+
+/* FLL4 (0x07) */
+#define NAU8821_HIGHBW_EN_SFT 15
+#define NAU8821_HIGHBW_EN (0x1 << NAU8821_HIGHBW_EN_SFT)
+#define NAU8821_FLL_REF_DIV_SFT 10
+#define NAU8821_FLL_REF_DIV_MASK (0x3 << NAU8821_FLL_REF_DIV_SFT)
+
+/* FLL5 (0x08) */
+#define NAU8821_FLL_PDB_DAC_EN (0x1 << 15)
+#define NAU8821_FLL_LOOP_FTR_EN (0x1 << 14)
+#define NAU8821_FLL_CLK_SW_SFT 13
+#define NAU8821_FLL_CLK_SW_MASK (0x1 << NAU8821_FLL_CLK_SW_SFT)
+#define NAU8821_FLL_CLK_SW_N2 (0x1 << NAU8821_FLL_CLK_SW_SFT)
+#define NAU8821_FLL_CLK_SW_REF (0x0 << NAU8821_FLL_CLK_SW_SFT)
+#define NAU8821_FLL_FTR_SW_SFT 12
+#define NAU8821_FLL_FTR_SW_MASK (0x1 << NAU8821_FLL_FTR_SW_SFT)
+#define NAU8821_FLL_FTR_SW_ACCU (0x1 << NAU8821_FLL_FTR_SW_SFT)
+#define NAU8821_FLL_FTR_SW_FILTER (0x0 << NAU8821_FLL_FTR_SW_SFT)
+
+/* FLL6 (0x09) */
+#define NAU8821_DCO_EN (0x1 << 15)
+#define NAU8821_SDM_EN (0x1 << 14)
+#define NAU8821_CUTOFF500 (0x1 << 13)
+
+/* FLL7 (0x0a) */
+#define NAU8821_FLL_FRACH_MASK 0xff
+
+/* FLL8 (0x0b) */
+#define NAU8821_FLL_FRACL_MASK 0xffff
+
+/* JACK_DET_CTRL (0x0d) */
+/* 0 - open, 1 - short to GND */
+#define NAU8821_SPKR_DWN1R_SFT 15
+#define NAU8821_SPKR_DWN1R (0x1 << NAU8821_SPKR_DWN1R_SFT)
+#define NAU8821_SPKR_DWN1L_SFT 14
+#define NAU8821_SPKR_DWN1L (0x1 << NAU8821_SPKR_DWN1L_SFT)
+#define NAU8821_JACK_DET_RESTART (0x1 << 9)
+#define NAU8821_JACK_DET_DB_BYPASS (0x1 << 8)
+#define NAU8821_JACK_INSERT_DEBOUNCE_SFT 5
+#define NAU8821_JACK_INSERT_DEBOUNCE_MASK (0x7 << NAU8821_JACK_INSERT_DEBOUNCE_SFT)
+#define NAU8821_JACK_EJECT_DEBOUNCE_SFT 2
+#define NAU8821_JACK_EJECT_DEBOUNCE_MASK (0x7 << NAU8821_JACK_EJECT_DEBOUNCE_SFT)
+#define NAU8821_JACK_POLARITY (0x1 << 1) /* 0 - active low, 1 - active high */
+
+/* INTERRUPT_MASK (0x0f) */
+#define NAU8821_IRQ_PIN_PULL_UP (0x1 << 14)
+#define NAU8821_IRQ_PIN_PULL_EN (0x1 << 13)
+#define NAU8821_IRQ_OUTPUT_EN (0x1 << 11)
+#define NAU8821_IRQ_RMS_EN (0x1 << 8)
+#define NAU8821_IRQ_KEY_RELEASE_EN (0x1 << 7)
+#define NAU8821_IRQ_KEY_PRESS_EN (0x1 << 6)
+#define NAU8821_IRQ_MIC_DET_EN (0x1 << 4)
+#define NAU8821_IRQ_EJECT_EN (0x1 << 2)
+#define NAU8821_IRQ_INSERT_EN 0x1
+
+/* IRQ_STATUS (0x10) */
+#define NAU8821_SHORT_CIRCUIT_IRQ (0x1 << 9)
+#define NAU8821_IMPEDANCE_MEAS_IRQ (0x1 << 8)
+#define NAU8821_KEY_IRQ_SFT 6
+#define NAU8821_KEY_IRQ_MASK (0x3 << NAU8821_KEY_IRQ_SFT)
+#define NAU8821_KEY_RELEASE_IRQ (0x2 << NAU8821_KEY_IRQ_SFT)
+#define NAU8821_KEY_SHORT_PRESS_IRQ (0x1 << NAU8821_KEY_IRQ_SFT)
+#define NAU8821_MIC_DETECT_IRQ (0x1 << 4)
+#define NAU8821_JACK_EJECT_IRQ_MASK (0x3 << 2)
+#define NAU8821_JACK_EJECT_DETECTED (0x1 << 2)
+#define NAU8821_JACK_INSERT_IRQ_MASK 0x3
+#define NAU8821_JACK_INSERT_DETECTED 0x1
+
+/* INTERRUPT_DIS_CTRL (0x12) */
+#define NAU8821_IRQ_KEY_RELEASE_DIS (0x1 << 7)
+#define NAU8821_IRQ_KEY_PRESS_DIS (0x1 << 6)
+#define NAU8821_IRQ_MIC_DIS (0x1 << 4)
+#define NAU8821_IRQ_EJECT_DIS (0x1 << 2)
+#define NAU8821_IRQ_INSERT_DIS 0x1
+
+/* DMIC_CTRL (0x13) */
+#define NAU8821_DMIC_DS_SFT 7
+#define NAU8821_DMIC_DS_MASK (0x1 << NAU8821_DMIC_DS_SFT)
+#define NAU8821_DMIC_DS_HIGH (0x1 << NAU8821_DMIC_DS_SFT)
+#define NAU8821_DMIC_DS_LOW (0x0 << NAU8821_DMIC_DS_SFT)
+#define NAU8821_DMIC_SRC_SFT 1
+#define NAU8821_DMIC_SRC_MASK (0x3 << NAU8821_DMIC_SRC_SFT)
+#define NAU8821_CLK_DMIC_SRC (0x2 << NAU8821_DMIC_SRC_SFT)
+#define NAU8821_DMIC_EN_SFT 0
+
+/* GPIO12_CTRL (0x1a) */
+#define NAU8821_JKDET_PULL_UP (0x1 << 11) /* 0 - pull down, 1 - pull up */
+#define NAU8821_JKDET_PULL_EN (0x1 << 9) /* 0 - enable pull, 1 - disable */
+#define NAU8821_JKDET_OUTPUT_EN (0x1 << 8) /* 0 - enable input, 1 - enable output */
+
+/* TDM_CTRL (0x1b) */
+#define NAU8821_TDM_EN_SFT 15
+#define NAU8821_TDM_EN (0x1 << NAU8821_TDM_EN_SFT)
+#define NAU8821_ADCPHS_SFT 13
+#define NAU8821_DACL_CH_SFT 7
+#define NAU8821_DACL_CH_MASK (0x7 << NAU8821_DACL_CH_SFT)
+#define NAU8821_DACR_CH_SFT 4
+#define NAU8821_DACR_CH_MASK (0x7 << NAU8821_DACR_CH_SFT)
+#define NAU8821_ADCL_CH_SFT 2
+#define NAU8821_ADCL_CH_MASK (0x3 << NAU8821_ADCL_CH_SFT)
+#define NAU8821_ADCR_CH_SFT 0
+#define NAU8821_ADCR_CH_MASK 0x3
+
+/* I2S_PCM_CTRL1 (0x1c) */
+#define NAU8821_I2S_BP_SFT 7
+#define NAU8821_I2S_BP_MASK (0x1 << NAU8821_I2S_BP_SFT)
+#define NAU8821_I2S_BP_INV (0x1 << NAU8821_I2S_BP_SFT)
+#define NAU8821_I2S_PCMB_SFT 6
+#define NAU8821_I2S_PCMB_MASK (0x1 << NAU8821_I2S_PCMB_SFT)
+#define NAU8821_I2S_PCMB_EN (0x1 << NAU8821_I2S_PCMB_SFT)
+#define NAU8821_I2S_DL_SFT 2
+#define NAU8821_I2S_DL_MASK (0x3 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DL_32 (0x3 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DL_24 (0x2 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DL_20 (0x1 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DL_16 (0x0 << NAU8821_I2S_DL_SFT)
+#define NAU8821_I2S_DF_MASK 0x3
+#define NAU8821_I2S_DF_PCM_AB 0x3
+#define NAU8821_I2S_DF_I2S 0x2
+#define NAU8821_I2S_DF_LEFT 0x1
+#define NAU8821_I2S_DF_RIGTH 0x0
+
+/* I2S_PCM_CTRL2 (0x1d) */
+#define NAU8821_I2S_TRISTATE_SFT 15
+#define NAU8821_I2S_TRISTATE (0x1 << NAU8821_I2S_TRISTATE_SFT)
+#define NAU8821_I2S_LRC_DIV_SFT 12
+#define NAU8821_I2S_LRC_DIV_MASK (0x3 << NAU8821_I2S_LRC_DIV_SFT)
+#define NAU8821_I2S_MS_SFT 3
+#define NAU8821_I2S_MS_MASK (0x1 << NAU8821_I2S_MS_SFT)
+#define NAU8821_I2S_MS_MASTER (0x1 << NAU8821_I2S_MS_SFT)
+#define NAU8821_I2S_MS_SLAVE (0x0 << NAU8821_I2S_MS_SFT)
+#define NAU8821_I2S_BLK_DIV_MASK 0x7
+
+/* LEFT_TIME_SLOT (0x1e) */
+#define NAU8821_TSLOT_L_OFFSET_MASK 0x3ff
+#define NAU8821_DIS_FS_SHORT_DET (0x1 << 13)
+
+/* RIGHT_TIME_SLOT (0x1f) */
+#define NAU8821_TSLOT_R_OFFSET_MASK 0x3ff
+
+/* BIQ0_COF10 (0x2a) */
+#define NAU8821_BIQ0_ADC_EN_SFT 3
+#define NAU8821_BIQ0_ADC_EN_EN (0x1 << NAU8821_BIQ0_ADC_EN_SFT)
+
+/* ADC_RATE (0x2b) */
+#define NAU8821_ADC_SYNC_DOWN_SFT 0
+#define NAU8821_ADC_SYNC_DOWN_MASK 0x3
+#define NAU8821_ADC_SYNC_DOWN_256 0x3
+#define NAU8821_ADC_SYNC_DOWN_128 0x2
+#define NAU8821_ADC_SYNC_DOWN_64 0x1
+#define NAU8821_ADC_SYNC_DOWN_32 0x0
+#define NAU8821_ADC_L_SRC_SFT 15
+#define NAU8821_ADC_L_SRC_EN (0x1 << NAU8821_ADC_L_SRC_SFT)
+#define NAU8821_ADC_R_SRC_SFT 14
+#define NAU8821_ADC_R_SRC_EN (0x1 << NAU8821_ADC_R_SRC_SFT)
+
+/* DAC_CTRL1 (0x2c) */
+#define NAU8821_DAC_OVERSAMPLE_SFT 0
+#define NAU8821_DAC_OVERSAMPLE_MASK 0x7
+#define NAU8821_DAC_OVERSAMPLE_32 0x4
+#define NAU8821_DAC_OVERSAMPLE_128 0x2
+#define NAU8821_DAC_OVERSAMPLE_256 0x1
+#define NAU8821_DAC_OVERSAMPLE_64 0x0
+
+/* DAC_DGAIN_CTRL (0x2f) */
+#define NAU8821_DAC1_TO_DAC0_ST_SFT 8
+#define NAU8821_DAC1_TO_DAC0_ST_MASK (0xff << NAU8821_DAC1_TO_DAC0_ST_SFT)
+#define NAU8821_DAC0_TO_DAC1_ST_SFT 0
+#define NAU8821_DAC0_TO_DAC1_ST_MASK 0xff
+
+/* MUTE_CTRL (0x31) */
+#define NAU8821_DAC_ZC_EN (0x1 << 12)
+#define NAU8821_DAC_SOFT_MUTE (0x1 << 9)
+#define NAU8821_ADC_ZC_EN (0x1 << 2)
+#define NAU8821_ADC_SOFT_MUTE (0x1 << 1)
+
+/* HSVOL_CTRL (0x32) */
+#define NAU8821_HP_MUTE (0x1 << 15)
+#define NAU8821_HP_MUTE_AUTO (0x1 << 14)
+#define NAU8821_HPL_MUTE (0x1 << 13)
+#define NAU8821_HPR_MUTE (0x1 << 12)
+#define NAU8821_HPL_VOL_SFT 4
+#define NAU8821_HPL_VOL_MASK (0x3 << NAU8821_HPL_VOL_SFT)
+#define NAU8821_HPR_VOL_SFT 0
+#define NAU8821_HPR_VOL_MASK (0x3 << NAU8821_HPR_VOL_SFT)
+
+/* DACR_CTRL (0x34) */
+#define NAU8821_DACR_CH_VOL_SFT 8
+#define NAU8821_DACR_CH_VOL_MASK (0xff << NAU8821_DACR_CH_VOL_SFT)
+#define NAU8821_DACL_CH_VOL_SFT 0
+#define NAU8821_DACL_CH_VOL_MASK 0xff
+
+/* ADC_DGAIN_CTRL1 (0x35) */
+#define NAU8821_ADCR_CH_VOL_SFT 8
+#define NAU8821_ADCR_CH_VOL_MASK (0xff << NAU8821_ADCR_CH_VOL_SFT)
+#define NAU8821_ADCL_CH_VOL_SFT 0
+#define NAU8821_ADCL_CH_VOL_MASK 0xff
+
+/* BIQ1_COF10 (0x4a) */
+#define NAU8821_BIQ1_DAC_EN_SFT 3
+#define NAU8821_BIQ1_DAC_EN_EN (0x1 << NAU8821_BIQ1_DAC_EN_SFT)
+
+/* CLASSG_CTRL (0x4b) */
+#define NAU8821_CLASSG_TIMER_SFT 8
+#define NAU8821_CLASSG_TIMER_MASK (0x3f << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_64MS (0x20 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_32MS (0x10 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_16MS (0x8 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_8MS (0x4 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_2MS (0x2 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_TIMER_1MS (0x1 << NAU8821_CLASSG_TIMER_SFT)
+#define NAU8821_CLASSG_RDAC_EN_SFT 2
+#define NAU8821_CLASSG_RDAC_EN (0x1 << NAU8821_CLASSG_RDAC_EN_SFT)
+#define NAU8821_CLASSG_LDAC_EN_SFT 1
+#define NAU8821_CLASSG_LDAC_EN (0x1 << NAU8821_CLASSG_LDAC_EN_SFT)
+#define NAU8821_CLASSG_EN_SFT 0
+#define NAU8821_CLASSG_EN 0x1
+
+/* IMM_MODE_CTRL (0x4c) */
+#define NAU8821_IMM_THD_SFT 8
+#define NAU8821_IMM_THD_MASK (0x3f << NAU8821_IMM_THD_SFT)
+#define NAU8821_IMM_GEN_VOL_SFT 6
+#define NAU8821_IMM_GEN_VOL_MASK (0x3 << NAU8821_IMM_GEN_VOL_SFT)
+#define NAU8821_IMM_CYC_SFT 4
+#define NAU8821_IMM_CYC_MASK (0x3 << NAU8821_IMM_CYC_SFT)
+#define NAU8821_IMM_EN (0x1 << 3)
+#define NAU8821_IMM_DAC_SRC_MASK 0x3
+
+/* I2C_DEVICE_ID (0x58) */
+#define NAU8821_KEYDET (0x1 << 7)
+#define NAU8821_MICDET (0x1 << 6)
+#define NAU8821_SOFTWARE_ID_MASK 0x3
+
+/* BIAS_ADJ (0x66) */
+#define NAU8821_BIAS_HP_IMP (0x1 << 15)
+#define NAU8821_BIAS_TESTDAC_SFT 8
+#define NAU8821_BIAS_TESTDAC_EN (0x3 << NAU8821_BIAS_TESTDAC_SFT)
+#define NAU8821_BIAS_TESTDACR_EN (0x2 << NAU8821_BIAS_TESTDAC_SFT)
+#define NAU8821_BIAS_TESTDACL_EN (0x1 << NAU8821_BIAS_TESTDAC_SFT)
+#define NAU8821_BIAS_VMID (0x1 << 6)
+#define NAU8821_BIAS_VMID_SEL_SFT 4
+#define NAU8821_BIAS_VMID_SEL_MASK (0x3 << NAU8821_BIAS_VMID_SEL_SFT)
+
+/* ANALOG_CONTROL_1 (0x69) */
+#define NAU8821_JD_POL_SFT 2
+#define NAU8821_JD_POL_MASK (0x1 << NAU8821_JD_POL_SFT)
+#define NAU8821_JD_POL_INV (0x1 << NAU8821_JD_POL_SFT)
+#define NAU8821_JD_OUT_POL_SFT 1
+#define NAU8821_JD_OUT_POL_MASK (0x1 << NAU8821_JD_OUT_POL_SFT)
+#define NAU8821_JD_OUT_POL_INV (0x1 << NAU8821_JD_OUT_POL_SFT)
+#define NAU8821_JD_EN_SFT 0
+#define NAU8821_JD_EN 0x1
+
+/* ANALOG_CONTROL_2 (0x6a) */
+#define NAU8821_HP_NON_CLASSG_CURRENT_2xADJ (0x1 << 12)
+#define NAU8821_DAC_CAPACITOR_MSB (0x1 << 1)
+#define NAU8821_DAC_CAPACITOR_LSB 0x1
+
+/* ANALOG_ADC_1 (0x71) */
+#define NAU8821_MICDET_EN_SFT 0
+#define NAU8821_MICDET_MASK 0x1
+#define NAU8821_MICDET_DIS 0x1
+#define NAU8821_MICDET_EN 0x0
+
+/* ANALOG_ADC_2 (0x72) */
+#define NAU8821_ADC_VREFSEL_SFT 8
+#define NAU8821_ADC_VREFSEL_MASK (0x3 << NAU8821_ADC_VREFSEL_SFT)
+#define NAU8821_POWERUP_ADCL_SFT 6
+#define NAU8821_POWERUP_ADCL (0x1 << NAU8821_POWERUP_ADCL_SFT)
+#define NAU8821_POWERUP_ADCR_SFT 4
+#define NAU8821_POWERUP_ADCR (0x1 << NAU8821_POWERUP_ADCR_SFT)
+
+/* RDAC (0x73) */
+#define NAU8821_DACR_EN_SFT 13
+#define NAU8821_DACR_EN (0x3 << NAU8821_DACR_EN_SFT)
+#define NAU8821_DACL_EN_SFT 12
+#define NAU8821_DACL_EN (0x3 << NAU8821_DACL_EN_SFT)
+#define NAU8821_DACR_CLK_EN_SFT 9
+#define NAU8821_DACR_CLK_EN (0x3 << NAU8821_DACR_CLK_EN_SFT)
+#define NAU8821_DACL_CLK_EN_SFT 8
+#define NAU8821_DACL_CLK_EN (0x3 << NAU8821_DACL_CLK_EN_SFT)
+#define NAU8821_DAC_CLK_DELAY_SFT 4
+#define NAU8821_DAC_CLK_DELAY_MASK (0x7 << NAU8821_DAC_CLK_DELAY_SFT)
+#define NAU8821_DAC_VREF_SFT 2
+#define NAU8821_DAC_VREF_MASK (0x3 << NAU8821_DAC_VREF_SFT)
+
+/* MIC_BIAS (0x74) */
+#define NAU8821_MICBIAS_JKR2 (0x1 << 12)
+#define NAU8821_MICBIAS_POWERUP_SFT 8
+#define NAU8821_MICBIAS_VOLTAGE_SFT 0
+#define NAU8821_MICBIAS_VOLTAGE_MASK 0x7
+
+/* BOOST (0x76) */
+#define NAU8821_PRECHARGE_DIS (0x1 << 13)
+#define NAU8821_GLOBAL_BIAS_EN (0x1 << 12)
+#define NAU8821_HP_BOOST_DIS_SFT 9
+#define NAU8821_HP_BOOST_DIS (0x1 << NAU8821_HP_BOOST_DIS_SFT)
+#define NAU8821_HP_BOOST_G_DIS (0x1 << 8)
+#define NAU8821_SHORT_SHUTDOWN_EN (0x1 << 6)
+
+/* FEPGA (0x77) */
+#define NAU8821_FEPGA_MODEL_SFT 4
+#define NAU8821_FEPGA_MODEL_MASK (0xf << NAU8821_FEPGA_MODEL_SFT)
+#define NAU8821_FEPGA_MODER_SFT 0
+#define NAU8821_FEPGA_MODER_MASK 0xf
+
+/* PGA_GAIN (0x7e) */
+#define NAU8821_PGA_GAIN_L_SFT 8
+#define NAU8821_PGA_GAIN_L_MASK (0x3f << NAU8821_PGA_GAIN_L_SFT)
+#define NAU8821_PGA_GAIN_R_SFT 0
+#define NAU8821_PGA_GAIN_R_MASK 0x3f
+
+/* POWER_UP_CONTROL (0x7f) */
+#define NAU8821_PUP_PGA_L_SFT 15
+#define NAU8821_PUP_PGA_L (0x1 << NAU8821_PUP_PGA_L_SFT)
+#define NAU8821_PUP_PGA_R_SFT 14
+#define NAU8821_PUP_PGA_R (0x1 << NAU8821_PUP_PGA_R_SFT)
+#define NAU8821_PUP_INTEG_R_SFT 5
+#define NAU8821_PUP_INTEG_R (0x1 << NAU8821_PUP_INTEG_R_SFT)
+#define NAU8821_PUP_INTEG_L_SFT 4
+#define NAU8821_PUP_INTEG_L (0x1 << NAU8821_PUP_INTEG_L_SFT)
+#define NAU8821_PUP_DRV_INSTG_R_SFT 3
+#define NAU8821_PUP_DRV_INSTG_R (0x1 << NAU8821_PUP_DRV_INSTG_R_SFT)
+#define NAU8821_PUP_DRV_INSTG_L_SFT 2
+#define NAU8821_PUP_DRV_INSTG_L (0x1 << NAU8821_PUP_DRV_INSTG_L_SFT)
+#define NAU8821_PUP_MAIN_DRV_R_SFT 1
+#define NAU8821_PUP_MAIN_DRV_R (0x1 << NAU8821_PUP_MAIN_DRV_R_SFT)
+#define NAU8821_PUP_MAIN_DRV_L_SFT 0
+#define NAU8821_PUP_MAIN_DRV_L 0x1
+
+/* CHARGE_PUMP (0x80) */
+#define NAU8821_JAMNODCLOW (0x1 << 10)
+#define NAU8821_POWER_DOWN_DACR_SFT 9
+#define NAU8821_POWER_DOWN_DACR (0x1 << NAU8821_POWER_DOWN_DACR_SFT)
+#define NAU8821_POWER_DOWN_DACL_SFT 8
+#define NAU8821_POWER_DOWN_DACL (0x1 << NAU8821_POWER_DOWN_DACL_SFT)
+#define NAU8821_CHANRGE_PUMP_EN_SFT 5
+#define NAU8821_CHANRGE_PUMP_EN (0x1 << NAU8821_CHANRGE_PUMP_EN_SFT)
+
+/* GENERAL_STATUS (0x82) */
+#define NAU8821_GPIO2_IN_SFT 1
+#define NAU8821_GPIO2_IN (0x1 << NAU8821_GPIO2_IN_SFT)
+
+#define NUVOTON_CODEC_DAI "nau8821-hifi"
+
+/* System Clock Source */
+enum {
+ NAU8821_CLK_DIS,
+ NAU8821_CLK_MCLK,
+ NAU8821_CLK_INTERNAL,
+ NAU8821_CLK_FLL_MCLK,
+ NAU8821_CLK_FLL_BLK,
+ NAU8821_CLK_FLL_FS,
+};
+
+struct nau8821 {
+ struct device *dev;
+ struct regmap *regmap;
+ struct snd_soc_dapm_context *dapm;
+ struct snd_soc_jack *jack;
+ struct work_struct jdet_work;
+ int irq;
+ int clk_id;
+ int micbias_voltage;
+ int vref_impedance;
+ bool jkdet_enable;
+ bool jkdet_pull_enable;
+ bool jkdet_pull_up;
+ int jkdet_polarity;
+ int jack_insert_debounce;
+ int jack_eject_debounce;
+ int fs;
+ int dmic_clk_threshold;
+};
+
+int nau8821_enable_jack_detect(struct snd_soc_component *component,
+ struct snd_soc_jack *jack);
+
+#endif /* __NAU8821_H__ */
--
2.25.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH] ASoC: nau8821: new driver
2021-10-01 10:31 Seven Lee
@ 2021-10-02 1:37 ` Mark Brown
0 siblings, 0 replies; 8+ messages in thread
From: Mark Brown @ 2021-10-02 1:37 UTC (permalink / raw)
To: Seven Lee
Cc: alsa-devel, scott6986, Mark Brown, KCHSU0, lgirdwood, YHCHuang,
michelle.chen, CTLIN0, dardar923, supercraig0719
On Fri, 1 Oct 2021 18:31:08 +0800, Seven Lee wrote:
> The driver is for codec NAU88L21 of Nuvoton Technology Corporation.
> The NAU88L21 is an ultra-low power high performance audio codec that
> supports both analog and digital audio functions.
>
>
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/1] ASoC: nau8821: new driver
commit: aab1ad11d69fa7f35cb88105614ea7911598e1d6
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2021-10-02 1:38 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-08-09 10:10 [PATCH] ASoC: nau8821: new driver Seven Lee
2021-08-09 10:44 ` Amadeusz Sławiński
2021-08-17 5:58 ` Seven Lee
2021-08-18 3:19 ` Seven Lee
2021-08-18 3:30 ` John Hsu
2021-08-18 7:23 ` Amadeusz Sławiński
2021-10-01 10:31 Seven Lee
2021-10-02 1:37 ` Mark Brown
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.