* [PATCH 0/5] Add CM-T35 support
@ 2009-12-08 21:11 Mike Rapoport
2009-12-08 21:11 ` [PATCH 1/5] u-boot git: add cm-t35 support Mike Rapoport
` (4 more replies)
0 siblings, 5 replies; 11+ messages in thread
From: Mike Rapoport @ 2009-12-08 21:11 UTC (permalink / raw)
To: openembedded-devel
This patch adds support for CM-T35 system-on-module based on OMAP3 SoC.
Mike Rapoport (5):
u-boot git: add cm-t35 support
linux-omap 2.6.32: add cm-t35 support
cm-t35: add machine configuration
angstrom-led-config: Add LED setup for the cm-t35 and bump PR.
xserver-xorg-conf: add cm-t35 support
conf/machine/cm-t35.conf | 46 +
recipes/angstrom/angstrom-led-config.bb | 2 +-
recipes/angstrom/angstrom-led-config/cm-t35/leds | 2 +
.../0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch | 159 ++
...do24m-ensure-chip-select-changes-between-.patch | 30 +
...002-omap3-cm-t35-add-DSS2-display-support.patch | 307 ++++
...03-omap3-cm-t35-update-defconfig-for-DSS2.patch | 145 ++
.../0004-omap3-cm-t35-add-cm-t35-mux-configs.patch | 427 +++++
.../0006-omap3-cm-t35-update-defconfig.patch | 87 +
recipes/linux/linux-omap-2.6.32/cm-t35/defconfig | 1823 ++++++++++++++++++++
recipes/linux/linux-omap_2.6.32.bb | 12 +-
recipes/u-boot/u-boot-git/cm-t35/cm-t35.patch | 1487 ++++++++++++++++
recipes/u-boot/u-boot_git.bb | 2 +
.../xserver-xorg-conf/cm-t35/xorg.conf | 29 +
recipes/xorg-xserver/xserver-xorg-conf_0.1.bb | 2 +-
15 files changed, 4557 insertions(+), 3 deletions(-)
create mode 100644 conf/machine/cm-t35.conf
create mode 100644 recipes/angstrom/angstrom-led-config/cm-t35/leds
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0001-backlight-tdo24m-ensure-chip-select-changes-between-.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0002-omap3-cm-t35-add-DSS2-display-support.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0003-omap3-cm-t35-update-defconfig-for-DSS2.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0004-omap3-cm-t35-add-cm-t35-mux-configs.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0006-omap3-cm-t35-update-defconfig.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/defconfig
create mode 100644 recipes/u-boot/u-boot-git/cm-t35/cm-t35.patch
create mode 100644 recipes/xorg-xserver/xserver-xorg-conf/cm-t35/xorg.conf
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 1/5] u-boot git: add cm-t35 support
2009-12-08 21:11 [PATCH 0/5] Add CM-T35 support Mike Rapoport
@ 2009-12-08 21:11 ` Mike Rapoport
2009-12-08 21:11 ` [PATCH 2/5] linux-omap 2.6.32: " Mike Rapoport
` (3 subsequent siblings)
4 siblings, 0 replies; 11+ messages in thread
From: Mike Rapoport @ 2009-12-08 21:11 UTC (permalink / raw)
To: openembedded-devel
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
---
recipes/u-boot/u-boot-git/cm-t35/cm-t35.patch | 1487 +++++++++++++++++++++++++
recipes/u-boot/u-boot_git.bb | 2 +
2 files changed, 1489 insertions(+), 0 deletions(-)
create mode 100644 recipes/u-boot/u-boot-git/cm-t35/cm-t35.patch
diff --git a/recipes/u-boot/u-boot-git/cm-t35/cm-t35.patch b/recipes/u-boot/u-boot-git/cm-t35/cm-t35.patch
new file mode 100644
index 0000000..10e84a2
--- /dev/null
+++ b/recipes/u-boot/u-boot-git/cm-t35/cm-t35.patch
@@ -0,0 +1,1487 @@
+diff --git a/MAINTAINERS b/MAINTAINERS
+index d70a9d2..94e45f4 100644
+--- a/MAINTAINERS
++++ b/MAINTAINERS
+@@ -677,6 +677,10 @@ Stelian Pop <stelian.pop@leadtechdesign.com>
+ at91sam9263ek ARM926EJS (AT91SAM9263 SoC)
+ at91sam9rlek ARM926EJS (AT91SAM9RL SoC)
+
++Mike Rapoport <mike@compulab.co.il>
++
++ cm_t35 ARM CORTEX-A8 (OMAP3xx SoC)
++
+ Tom Rix <Tom.Rix@windriver.com>
+
+ omap3_zoom2 ARM CORTEX-A8 (OMAP3xx SoC)
+diff --git a/MAKEALL b/MAKEALL
+index d63c5c2..e131c62 100755
+--- a/MAKEALL
++++ b/MAKEALL
+@@ -612,6 +612,7 @@ LIST_ARM11=" \
+ ## ARM Cortex-A8 Systems
+ #########################################################################
+ LIST_ARM_CORTEX_A8=" \
++ cm_t35 \
+ devkit8000 \
+ omap3_beagle \
+ omap3_overo \
+diff --git a/Makefile b/Makefile
+index bcb3fe9..9d6150a 100644
+--- a/Makefile
++++ b/Makefile
+@@ -3143,6 +3143,8 @@ SMN42_config : unconfig
+ #########################################################################
+ ## ARM CORTEX Systems
+ #########################################################################
++cm_t35_config : unconfig
++ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 cm_t35 NULL omap3
+
+ devkit8000_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 devkit8000 timll omap3
+diff --git a/board/cm_t35/Makefile b/board/cm_t35/Makefile
+new file mode 100644
+index 0000000..320a817
+--- /dev/null
++++ b/board/cm_t35/Makefile
+@@ -0,0 +1,47 @@
++#
++# (C) Copyright 2000, 2001, 2002
++# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
++#
++# See file CREDITS for list of people who contributed to this
++# project.
++#
++# This program is free software; you can redistribute it and/or
++# modify it under the terms of the GNU General Public License as
++# published by the Free Software Foundation; either version 2 of
++# the License, or (at your option) any later version.
++#
++# This program is distributed in the hope that it will be useful,
++# but WITHOUT ANY WARRANTY; without even the implied warranty of
++# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++# GNU General Public License for more details.
++#
++# You should have received a copy of the GNU General Public License
++# along with this program; if not, write to the Free Software
++# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
++# MA 02111-1307 USA
++#
++
++include $(TOPDIR)/config.mk
++
++LIB = $(obj)lib$(BOARD).a
++
++COBJS := cm_t35.o
++
++SRCS := $(COBJS:.o=.c)
++OBJS := $(addprefix $(obj),$(COBJS))
++
++$(LIB): $(obj).depend $(OBJS)
++ $(AR) $(ARFLAGS) $@ $(OBJS)
++
++clean:
++ rm -f $(OBJS)
++
++distclean: clean
++ rm -f $(LIB) core *.bak $(obj).depend
++
++#########################################################################
++
++# defines $(obj).depend target
++include $(SRCTREE)/rules.mk
++
++sinclude $(obj).depend
+diff --git a/board/cm_t35/cm_t35.c b/board/cm_t35/cm_t35.c
+new file mode 100644
+index 0000000..a9bb86f
+--- /dev/null
++++ b/board/cm_t35/cm_t35.c
+@@ -0,0 +1,257 @@
++/*
++ * (C) Copyright 2009
++ * CompuLab, Ltd. <www.compulab.co.il>
++ *
++ * Authors :
++ * Igor Vaisbein <igor@compulab.co.il>
++ * Mike Rapoport <mike@compulab.co.il>
++ *
++ * Derived from omap3evm and Beagle Board by
++ * Manikandan Pillai <mani.pillai@ti.com>
++ * Richard Woodruff <r-woodruff2@ti.com>
++ * Syed Mohammed Khasim <x0khasim@ti.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
++ * MA 02111-1307 USA
++ */
++
++#include <common.h>
++#include <netdev.h>
++#include <net.h>
++#include <i2c.h>
++#include <twl4030.h>
++
++#include <asm/io.h>
++#include <asm/setup.h>
++#include <asm/arch/mem.h>
++#include <asm/arch/mux.h>
++#include <asm/arch/sys_proto.h>
++#include <asm/mach-types.h>
++
++#include "cm_t35.h"
++
++static u32 gpmc_net_config[GPMC_MAX_REG] = {
++ NET_GPMC_CONFIG1,
++ NET_GPMC_CONFIG2,
++ NET_GPMC_CONFIG3,
++ NET_GPMC_CONFIG4,
++ NET_GPMC_CONFIG5,
++ NET_GPMC_CONFIG6,
++ 0
++};
++
++static u32 gpmc_nand_config[GPMC_MAX_REG] = {
++ SMNAND_GPMC_CONFIG1,
++ SMNAND_GPMC_CONFIG2,
++ SMNAND_GPMC_CONFIG3,
++ SMNAND_GPMC_CONFIG4,
++ SMNAND_GPMC_CONFIG5,
++ SMNAND_GPMC_CONFIG6,
++ 0,
++};
++
++DECLARE_GLOBAL_DATA_PTR;
++
++/*
++ * Routine: board_init
++ * Description: Early hardware init.
++ */
++int board_init(void)
++{
++ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
++
++ enable_gpmc_cs_config(gpmc_nand_config, &gpmc_cfg->cs[0],
++ CONFIG_SYS_NAND_BASE, GPMC_SIZE_16M);
++
++ /* board id for Linux */
++ gd->bd->bi_arch_number = MACH_TYPE_CM_T35;
++ /* boot param addr */
++ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
++
++ return 0;
++}
++
++/*
++ * Routine: misc_init_r
++ * Description: init i2c and dieid
++ */
++int misc_init_r(void)
++{
++#ifdef CONFIG_DRIVER_OMAP34XX_I2C
++ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
++#endif
++
++ dieid_num_r();
++
++ return 0;
++}
++
++/*
++ * Routine: set_muxconf_regs
++ * Description: Setting up the configuration Mux registers specific to the
++ * hardware. Many pins need to be moved from protect to primary
++ * mode.
++ */
++void set_muxconf_regs(void)
++{
++ MUX_CM_T35();
++}
++
++/*
++ * Routine: get_board_serial
++ * Description: read system serial number
++ */
++void get_board_serial(struct tag_serialnr *serialnr)
++{
++ u32 low, high;
++ int rc;
++
++ memset(serialnr, 0, sizeof(*serialnr));
++
++ rc = i2c_read(0x50, 0x8, 1, &low, sizeof(low));
++ if (rc)
++ return;
++
++ rc = i2c_read(0x50, 0xc, 1, &high, sizeof(high));
++ if (rc)
++ return;
++
++ if (low != 0xffffffff && high != 0xffffffff) {
++ serialnr->low = low;
++ serialnr->high = high;
++ }
++};
++
++/*
++ * Routine: get_board_rev
++ * Description: read system revision
++ */
++u32 get_board_rev(void)
++{
++ u16 rev;
++ int rc;
++
++ rc = i2c_read(0x50, 0x6, 1, &rev, sizeof(rev));
++ if (rc)
++ return 0;
++
++ return rev;
++};
++
++/*
++ * Routine: setup_net_chip_gmpc
++ * Description: Setting up the configuration GPMC registers specific to the
++ * Ethernet hardware.
++ */
++static void setup_net_chip_gmpc(void)
++{
++ struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
++
++ enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[5],
++ CM_T35_SMC911X_BASE, GPMC_SIZE_16M);
++ enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[4],
++ SB_T35_SMC911X_BASE, GPMC_SIZE_16M);
++
++ /* Enable off mode for NWE in PADCONF_GPMC_NWE register */
++ writew(readw(&ctrl_base->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
++
++ /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
++ writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
++
++ /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
++ writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
++ &ctrl_base->gpmc_nadv_ale);
++}
++
++#ifdef CONFIG_DRIVER_OMAP34XX_I2C
++/*
++ * Routine: reset_net_chip
++ * Description: reset the Ethernet controller via TPS65930 GPIO
++ */
++static void reset_net_chip(void)
++{
++ /* Set GPIO1 of TPS65930 as output */
++ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
++ TWL4030_BASEADD_GPIO+0x03);
++ /* Send a pulse on the GPIO pin */
++ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
++ TWL4030_BASEADD_GPIO+0x0C);
++ udelay(1);
++ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
++ TWL4030_BASEADD_GPIO+0x09);
++ udelay(1);
++ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
++ TWL4030_BASEADD_GPIO+0x0C);
++}
++#else
++static inline void reset_net_chip(void) {}
++#endif
++
++/*
++ * Routine: handle_mac_address
++ * Description: prepare MAC address for on-board Ethernet.
++ */
++static int handle_mac_address(void)
++{
++ unsigned char enetaddr[6];
++ int rc;
++
++ memset(enetaddr, 0, 6);
++ rc = eth_getenv_enetaddr("ethaddr", enetaddr);
++ if (rc)
++ return 0;
++
++#ifdef CONFIG_DRIVER_OMAP34XX_I2C
++ rc = i2c_read(0x50, 0, 1, enetaddr, 6);
++ if (rc)
++ return rc;
++#endif
++
++ if (!is_valid_ether_addr(enetaddr))
++ return -1;
++
++ return eth_setenv_enetaddr("ethaddr", enetaddr);
++}
++
++/*
++ * Routine: board_eth_init
++ * Description: initialize module and base-board Ethernet chips
++ */
++int board_eth_init(bd_t *bis)
++{
++ int rc = 0, rc1 = 0;
++
++#ifdef CONFIG_SMC911X
++ setup_net_chip_gmpc();
++ reset_net_chip();
++
++ rc1 = handle_mac_address();
++ if (rc1)
++ printf("CM-T35: No MAC address found\n");
++
++ rc1 = smc911x_initialize(0, CM_T35_SMC911X_BASE);
++ if (rc1 > 0)
++ rc++;
++
++ rc1 = smc911x_initialize(1, SB_T35_SMC911X_BASE);
++ if (rc1 > 0)
++ rc++;
++#endif
++
++ return rc;
++}
+diff --git a/board/cm_t35/cm_t35.h b/board/cm_t35/cm_t35.h
+new file mode 100644
+index 0000000..549422c
+--- /dev/null
++++ b/board/cm_t35/cm_t35.h
+@@ -0,0 +1,180 @@
++/*
++ * (C) Copyright 2009 CompuLab, Ltd
++ * Authors:
++ * Igor Vaisbein <igor@compulab.co.il>
++ * Mike Rapoport <mike@compulab.co.il>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
++ * MA 02111-1307 USA
++ */
++#ifndef _CM_T35_H_
++#define _CM_T35_H_
++
++const omap3_sysinfo sysinfo = {
++ DDR_DISCRETE,
++ "CM-T35 board",
++ "NAND",
++};
++
++/* static void setup_net_chip(void); */
++
++/*
++ * IEN - Input Enable
++ * IDIS - Input Disable
++ * PTD - Pull type Down
++ * PTU - Pull type Up
++ * DIS - Pull type selection is inactive
++ * EN - Pull type selection is active
++ * M0 - Mode 0
++ * The commented string gives the final mux configuration for that pin
++ */
++#define MUX_CM_T35() \
++ /*SDRC*/\
++ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
++ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
++ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
++ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
++ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
++ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
++ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
++ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
++ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
++ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
++ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
++ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
++ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
++ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
++ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
++ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
++ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
++ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
++ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
++ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
++ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
++ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
++ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
++ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
++ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
++ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
++ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
++ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
++ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
++ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
++ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
++ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
++ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
++ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
++ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
++ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
++ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
++ /*GPMC*/\
++ MUX_VAL(CP(GPMC_A1), (IDIS | PTU | EN | M0)) /*GPMC_A1*/\
++ MUX_VAL(CP(GPMC_A2), (IDIS | PTU | EN | M0)) /*GPMC_A2*/\
++ MUX_VAL(CP(GPMC_A3), (IDIS | PTU | EN | M0)) /*GPMC_A3*/\
++ MUX_VAL(CP(GPMC_A4), (IDIS | PTU | EN | M0)) /*GPMC_A4*/\
++ MUX_VAL(CP(GPMC_A5), (IDIS | PTU | EN | M0)) /*GPMC_A5*/\
++ MUX_VAL(CP(GPMC_A6), (IDIS | PTU | EN | M0)) /*GPMC_A6*/\
++ MUX_VAL(CP(GPMC_A7), (IDIS | PTU | EN | M0)) /*GPMC_A7*/\
++ MUX_VAL(CP(GPMC_A8), (IDIS | PTU | EN | M0)) /*GPMC_A8*/\
++ MUX_VAL(CP(GPMC_A9), (IDIS | PTU | EN | M0)) /*GPMC_A9*/\
++ MUX_VAL(CP(GPMC_A10), (IDIS | PTU | EN | M0)) /*GPMC_A10*/\
++ MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0)) /*GPMC_D0*/\
++ MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0)) /*GPMC_D1*/\
++ MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0)) /*GPMC_D2*/\
++ MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0)) /*GPMC_D3*/\
++ MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0)) /*GPMC_D4*/\
++ MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0)) /*GPMC_D5*/\
++ MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0)) /*GPMC_D6*/\
++ MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0)) /*GPMC_D7*/\
++ MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0)) /*GPMC_D8*/\
++ MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0)) /*GPMC_D9*/\
++ MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0)) /*GPMC_D10*/\
++ MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0)) /*GPMC_D11*/\
++ MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0)) /*GPMC_D12*/\
++ MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0)) /*GPMC_D13*/\
++ MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0)) /*GPMC_D14*/\
++ MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0)) /*GPMC_D15*/\
++ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
++ /*Expansion card */\
++ MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/ \
++ MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/ \
++ MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/ \
++ MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/ \
++ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/ \
++ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/ \
++ /* SB-T35 Ethernet */\
++ MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M0)) /*GPMC_nCS4*/\
++ /* CM-T35 Ethernet */\
++ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTU | DIS | M0)) /*GPMC_nCS5*/\
++ MUX_VAL(CP(GPMC_CLK), (IEN | PTD | DIS | M4)) /*GPIO_59*/\
++ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*nADV_ALE*/\
++ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*nOE*/\
++ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*nWE*/\
++ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTU | EN | M0)) /*nBE0_CLE*/\
++ MUX_VAL(CP(GPMC_NBE1), (IDIS | PTD | DIS | M4)) /*GPIO_61*/\
++ MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*nWP*/\
++ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*WAIT0*/\
++ /*DSS*/\
++ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
++ MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
++ MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
++ MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
++ MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
++ MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
++ MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
++ MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
++ MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
++ MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
++ MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
++ MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
++ MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
++ MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
++ MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
++ MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
++ MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
++ MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
++ MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
++ MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
++ MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
++ MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
++ MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
++ MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
++ MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
++ MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
++ MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
++ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
++ /*Serial Interface*/\
++ MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /*UART3_RX*/\
++ MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX*/\
++ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
++ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
++ /*Control and debug */\
++ MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
++ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
++ MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
++ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*OFF_MODE*/\
++ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) /*CLKOUT1*/\
++ MUX_VAL(CP(SYS_CLKOUT2), (IDIS | PTD | DIS | M4)) /*green LED*/\
++ MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0)) /*JTAG_nTRST*/\
++ MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0)) /*JTAG_TCK*/\
++ MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0)) /*JTAG_TMS*/\
++ MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0)) /*JTAG_TDI*/\
++ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
++ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7)) /*sdrc_cke1*/\
++
++#endif
+diff --git a/board/cm_t35/config.mk b/board/cm_t35/config.mk
+new file mode 100644
+index 0000000..a90c86a
+--- /dev/null
++++ b/board/cm_t35/config.mk
+@@ -0,0 +1,30 @@
++#
++# (C) Copyright 2009
++# CompuLab, Ltd., <www.compulab.co.il>
++#
++# See file CREDITS for list of people who contributed to this
++# project.
++#
++# This program is free software; you can redistribute it and/or
++# modify it under the terms of the GNU General Public License as
++# published by the Free Software Foundation; either version 2 of
++# the License, or (at your option) any later version.
++#
++# This program is distributed in the hope that it will be useful,
++# but WITHOUT ANY WARRANTY; without even the implied warranty of
++# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++# GNU General Public License for more details.
++#
++# You should have received a copy of the GNU General Public License
++# along with this program; if not, write to the Free Software
++# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
++# MA 02111-1307 USA
++#
++# Physical Address:
++# 8000'0000 (bank0)
++#
++# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
++# (mem base + reserved)
++
++# For use with external or internal boots.
++TEXT_BASE = 0x80e80000
+diff --git a/cpu/arm_cortexa8/omap3/board.c b/cpu/arm_cortexa8/omap3/board.c
+index dd2c940..0b3805a 100644
+--- a/cpu/arm_cortexa8/omap3/board.c
++++ b/cpu/arm_cortexa8/omap3/board.c
+@@ -291,8 +291,11 @@ int dram_init(void)
+
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = size0;
++
++#if (CONFIG_NR_DRAM_BANKS > 1)
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + get_sdr_cs_offset(CS1);
+ gd->bd->bi_dram[1].size = size1;
++#endif
+
+ return 0;
+ }
+diff --git a/cpu/arm_cortexa8/omap3/mem.c b/cpu/arm_cortexa8/omap3/mem.c
+index 8b8cd6d..be254b5 100644
+--- a/cpu/arm_cortexa8/omap3/mem.c
++++ b/cpu/arm_cortexa8/omap3/mem.c
+@@ -35,11 +35,6 @@
+ * Only One NAND allowed on board at a time.
+ * The GPMC CS Base for the same
+ */
+-unsigned int boot_flash_base;
+-unsigned int boot_flash_off;
+-unsigned int boot_flash_sec;
+-unsigned int boot_flash_type;
+-volatile unsigned int boot_flash_env_addr;
+
+ struct gpmc *gpmc_cfg;
+
+@@ -223,10 +218,6 @@ void gpmc_init(void)
+ const u32 *gpmc_config = NULL;
+ u32 base = 0;
+ u32 size = 0;
+-#if defined(CONFIG_ENV_IS_IN_NAND) || defined(CONFIG_ENV_IS_IN_ONENAND)
+- u32 f_off = CONFIG_SYS_MONITOR_LEN;
+- u32 f_sec = 0;
+-#endif
+ #endif
+ u32 config = 0;
+
+@@ -251,15 +242,6 @@ void gpmc_init(void)
+ base = PISMO1_NAND_BASE;
+ size = PISMO1_NAND_SIZE;
+ enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[0], base, size);
+-#if defined(CONFIG_ENV_IS_IN_NAND)
+- f_off = SMNAND_ENV_OFFSET;
+- f_sec = (128 << 10); /* 128 KiB */
+- /* env setup */
+- boot_flash_base = base;
+- boot_flash_off = f_off;
+- boot_flash_sec = f_sec;
+- boot_flash_env_addr = f_off;
+-#endif
+ #endif
+
+ #if defined(CONFIG_CMD_ONENAND)
+@@ -267,14 +249,5 @@ void gpmc_init(void)
+ base = PISMO1_ONEN_BASE;
+ size = PISMO1_ONEN_SIZE;
+ enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[0], base, size);
+-#if defined(CONFIG_ENV_IS_IN_ONENAND)
+- f_off = ONENAND_ENV_OFFSET;
+- f_sec = (128 << 10); /* 128 KiB */
+- /* env setup */
+- boot_flash_base = base;
+- boot_flash_off = f_off;
+- boot_flash_sec = f_sec;
+- boot_flash_env_addr = f_off;
+-#endif
+ #endif
+ }
+diff --git a/cpu/arm_cortexa8/omap3/sys_info.c b/cpu/arm_cortexa8/omap3/sys_info.c
+index 31b2003..3f66a6a 100644
+--- a/cpu/arm_cortexa8/omap3/sys_info.c
++++ b/cpu/arm_cortexa8/omap3/sys_info.c
+@@ -173,15 +173,6 @@ u32 get_gpmc0_width(void)
+ return WIDTH_16BIT;
+ }
+
+-/*************************************************************************
+- * get_board_rev() - setup to pass kernel board revision information
+- * returns:(bit[0-3] sub version, higher bit[7-4] is higher version)
+- *************************************************************************/
+-u32 get_board_rev(void)
+-{
+- return 0x20;
+-}
+-
+ /********************************************************
+ * get_base(); get upper addr of current execution
+ *******************************************************/
+diff --git a/doc/README.omap3 b/doc/README.omap3
+index 6227151..1c1c16f 100644
+--- a/doc/README.omap3
++++ b/doc/README.omap3
+@@ -21,6 +21,8 @@ Currently the following boards are supported:
+
+ * TI/Logic PD Zoom 2 [7]
+
++* CompuLab Ltd. CM-T35 [8]
++
+ Toolchain
+ =========
+
+@@ -61,6 +63,11 @@ make
+ make omap3_zoom2_config
+ make
+
++* CM-T35:
++
++make cm_t35_config
++make
++
+ Custom commands
+ ===============
+
+@@ -119,7 +126,7 @@ To read a bit :
+ Acknowledgements
+ ================
+
+-OMAP3 U-Boot is based on U-Boot tar ball [8] for BeagleBoard and EVM done by
++OMAP3 U-Boot is based on U-Boot tar ball [9] for BeagleBoard and EVM done by
+ several TI employees.
+
+ Links
+@@ -153,6 +160,11 @@ http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit
+ [7] TI/Logic PD Zoom 2
+
+ http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
+-[8] TI OMAP3 U-Boot:
++
++[8] CompuLab Ltd. CM-T35:
++
++http://www.compulab.co.il/t35/html/t35-cm-datasheet.htm
++
++[9] TI OMAP3 U-Boot:
+
+ http://beagleboard.googlecode.com/files/u-boot_beagle_revb.tar.gz
+diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c
+index c027abe..8509b6a 100644
+--- a/drivers/net/smc911x.c
++++ b/drivers/net/smc911x.c
+@@ -37,7 +37,7 @@ void pkt_data_push(struct eth_device *dev, u32 addr, u32 val) \
+
+ #define mdelay(n) udelay((n)*1000)
+
+-static void smx911x_handle_mac_address(struct eth_device *dev)
++static void smc911x_handle_mac_address(struct eth_device *dev)
+ {
+ unsigned long addrh, addrl;
+ uchar *m = dev->enetaddr;
+@@ -47,7 +47,7 @@ static void smx911x_handle_mac_address(struct eth_device *dev)
+ smc911x_set_mac_csr(dev, ADDRL, addrl);
+ smc911x_set_mac_csr(dev, ADDRH, addrh);
+
+- printf(DRIVERNAME ": MAC %pM\n", m);
++ printf("%s: MAC %pM\n", dev->name, m);
+ }
+
+ static int smc911x_miiphy_read(struct eth_device *dev,
+@@ -119,12 +119,12 @@ static void smc911x_phy_configure(struct eth_device *dev)
+ goto err_out;
+ } while (!(status & PHY_BMSR_LS));
+
+- printf(DRIVERNAME ": phy initialized\n");
++ printf("%s: phy initialized\n", dev->name);
+
+ return;
+
+ err_out:
+- printf(DRIVERNAME ": autonegotiation timed out\n");
++ printf("%s: autonegotiation timed out\n", dev->name);
+ }
+
+ static void smc911x_enable(struct eth_device *dev)
+@@ -148,14 +148,14 @@ static int smc911x_init(struct eth_device *dev, bd_t * bd)
+ {
+ struct chip_id *id = dev->priv;
+
+- printf(DRIVERNAME ": detected %s controller\n", id->name);
++ printf("%s: detected %s controller\n", dev->name, id->name);
+
+ smc911x_reset(dev);
+
+ /* Configure the PHY, initialize the link state */
+ smc911x_phy_configure(dev);
+
+- smx911x_handle_mac_address(dev);
++ smc911x_handle_mac_address(dev);
+
+ /* Turn on Tx + Rx */
+ smc911x_enable(dev);
+@@ -193,7 +193,7 @@ static int smc911x_send(struct eth_device *dev,
+ if (!status)
+ return 0;
+
+- printf(DRIVERNAME ": failed to send packet: %s%s%s%s%s\n",
++ printf("%s: failed to send packet: %s%s%s%s%s\n", dev->name,
+ status & TX_STS_LOC ? "TX_STS_LOC " : "",
+ status & TX_STS_LATE_COLL ? "TX_STS_LATE_COLL " : "",
+ status & TX_STS_MANY_COLL ? "TX_STS_MANY_COLL " : "",
+@@ -206,6 +206,10 @@ static int smc911x_send(struct eth_device *dev,
+ static void smc911x_halt(struct eth_device *dev)
+ {
+ smc911x_reset(dev);
++
++#ifdef CONFIG_SMC911X_KEEP_MAC
++ smc911x_handle_mac_address(dev);
++#endif
+ }
+
+ static int smc911x_rx(struct eth_device *dev)
+@@ -225,9 +229,8 @@ static int smc911x_rx(struct eth_device *dev)
+ *data++ = pkt_data_pull(dev, RX_DATA_FIFO);
+
+ if (status & RX_STS_ES)
+- printf(DRIVERNAME
+- ": dropped bad packet. Status: 0x%08x\n",
+- status);
++ printf("%s: dropped bad packet. Status: 0x%08x\n",
++ dev->name, status);
+ else
+ NetReceive(NetRxPackets[0], pktlen);
+ }
+@@ -238,6 +241,7 @@ static int smc911x_rx(struct eth_device *dev)
+ int smc911x_initialize(u8 dev_num, int base_addr)
+ {
+ unsigned long addrl, addrh;
++ unsigned char enetaddr[6];
+ struct eth_device *dev;
+
+ dev = malloc(sizeof(*dev));
+@@ -248,6 +252,7 @@ int smc911x_initialize(u8 dev_num, int base_addr)
+ memset(dev, 0, sizeof(*dev));
+
+ dev->iobase = base_addr;
++ sprintf(dev->name, "%s-%hu", DRIVERNAME, dev_num);
+
+ /* Try to detect chip. Will fail if not present. */
+ if (smc911x_detect_chip(dev)) {
+@@ -257,18 +262,20 @@ int smc911x_initialize(u8 dev_num, int base_addr)
+
+ addrh = smc911x_get_mac_csr(dev, ADDRH);
+ addrl = smc911x_get_mac_csr(dev, ADDRL);
+- dev->enetaddr[0] = addrl;
+- dev->enetaddr[1] = addrl >> 8;
+- dev->enetaddr[2] = addrl >> 16;
+- dev->enetaddr[3] = addrl >> 24;
+- dev->enetaddr[4] = addrh;
+- dev->enetaddr[5] = addrh >> 8;
++ enetaddr[0] = addrl;
++ enetaddr[1] = addrl >> 8;
++ enetaddr[2] = addrl >> 16;
++ enetaddr[3] = addrl >> 24;
++ enetaddr[4] = addrh;
++ enetaddr[5] = addrh >> 8;
++
++ if (is_valid_ether_addr(enetaddr))
++ memcpy(dev->enetaddr, enetaddr, 6);
+
+ dev->init = smc911x_init;
+ dev->halt = smc911x_halt;
+ dev->send = smc911x_send;
+ dev->recv = smc911x_rx;
+- sprintf(dev->name, "%s-%hu", DRIVERNAME, dev_num);
+
+ eth_register(dev);
+ return 1;
+diff --git a/drivers/net/smc911x.h b/drivers/net/smc911x.h
+index 05e007c..0ea6ac1 100644
+--- a/drivers/net/smc911x.h
++++ b/drivers/net/smc911x.h
+@@ -447,7 +447,7 @@ static int smc911x_detect_chip(struct eth_device *dev)
+ /* Special case -- no chip present */
+ return -1;
+ } else if (val != 0x87654321) {
+- printf(DRIVERNAME ": Invalid chip endian 0x%08lx\n", val);
++ printf("%s: Invalid chip endian 0x%08lx\n", __func__, val);
+ return -1;
+ }
+
+@@ -456,7 +456,7 @@ static int smc911x_detect_chip(struct eth_device *dev)
+ if (chip_ids[i].id == val) break;
+ }
+ if (!chip_ids[i].id) {
+- printf(DRIVERNAME ": Unknown chip ID %04lx\n", val);
++ printf("%s: Unknown chip ID %04lx\n", __func__, val);
+ return -1;
+ }
+
+@@ -480,8 +480,8 @@ static void smc911x_reset(struct eth_device *dev)
+ !(smc911x_reg_read(dev, PMT_CTRL) & PMT_CTRL_READY))
+ udelay(10);
+ if (!timeout) {
+- printf(DRIVERNAME
+- ": timeout waiting for PM restore\n");
++ printf("%s: timeout waiting for PM restore\n",
++ dev->name);
+ return;
+ }
+ }
+@@ -496,7 +496,7 @@ static void smc911x_reset(struct eth_device *dev)
+ udelay(10);
+
+ if (!timeout) {
+- printf(DRIVERNAME ": reset timeout\n");
++ printf("%s: reset timeout\n", dev->name);
+ return;
+ }
+
+diff --git a/examples/api/Makefile b/examples/api/Makefile
+index 04a270b..057e85a 100644
+--- a/examples/api/Makefile
++++ b/examples/api/Makefile
+@@ -49,6 +49,12 @@ ifeq ($(ARCH),ppc)
+ EXT_SOBJ_FILES-$(CONFIG_API) += lib_ppc/ppcstring.o
+ endif
+
++ifeq ($(ARCH),arm)
++ifneq (,$(findstring -mabi=aapcs-linux,$(PLATFORM_CPPFLAGS)))
++EXT_COBJ_FILES-$(CONFIG_API) += lib_arm/eabi_compat.o
++endif
++endif
++
+ # Create a list of source files so their dependencies can be auto-generated
+ SRCS += $(addprefix $(SRCTREE)/,$(EXT_COBJ_FILES-y:.o=.c))
+ SRCS += $(addprefix $(SRCTREE)/,$(EXT_SOBJ_FILES-y:.o=.S))
+@@ -81,6 +87,10 @@ $(obj)%.o: $(SRCTREE)/lib_generic/%.c
+ $(obj)%.o: $(SRCTREE)/lib_$(ARCH)/%.S
+ $(CC) -g $(CFLAGS) -c -o $@ $<
+
++# Rule to build architecture-specific library C files
++$(obj)%.o: $(SRCTREE)/lib_$(ARCH)/%.c
++ $(CC) -g $(CFLAGS) -c -o $@ $<
++
+ #########################################################################
+
+ # defines $(obj).depend target
+diff --git a/include/asm-arm/arch-omap3/cpu.h b/include/asm-arm/arch-omap3/cpu.h
+index 8ab2e39..7fdf00f 100644
+--- a/include/asm-arm/arch-omap3/cpu.h
++++ b/include/asm-arm/arch-omap3/cpu.h
+@@ -136,6 +136,10 @@ struct gpmc {
+ u32 ecc8_result; /* 0x21C */
+ u32 ecc9_result; /* 0x220 */
+ };
++
++/* Used for board specific gpmc initialization */
++extern struct gpmc *gpmc_cfg;
++
+ #else /* __ASSEMBLY__ */
+ #define GPMC_CONFIG1 0x00
+ #define GPMC_CONFIG2 0x04
+diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
+new file mode 100644
+index 0000000..37edbb5
+--- /dev/null
++++ b/include/configs/cm_t35.h
+@@ -0,0 +1,281 @@
++/*
++ * (C) Copyright 2009 CompuLab, Ltd.
++ *
++ * Authors :
++ * Igor Vaisbein <igor@compulab.co.il>
++ * Mike Rapoport <mike@compulab.co.il>
++ *
++ * Derived from omap3evm and Beagle Board by
++ * Manikandan Pillai <mani.pillai@ti.com>
++ * Richard Woodruff <r-woodruff2@ti.com>
++ * Syed Mohammed Khasim <x0khasim@ti.com>
++ *
++ * Configuration settings for the CompuLab CM-T35 board.
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
++ * MA 02111-1307 USA
++ */
++
++#ifndef __CONFIG_H
++#define __CONFIG_H
++
++/* High Level Configuration Options */
++#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
++#define CONFIG_OMAP 1 /* in a TI OMAP core */
++#define CONFIG_OMAP34XX 1 /* which is a 34XX */
++#define CONFIG_OMAP3430 1 /* which is in a 3430 */
++#define CONFIG_CM_T35 1 /* working with CM_T35 */
++
++#include <asm/arch/cpu.h> /* get chip and board defs */
++#include <asm/arch/omap3.h>
++
++#define CONFIG_DISPLAY_CPUINFO 1
++#define CONFIG_DISPLAY_BOARDINFO 1
++
++/* Clock Defines */
++#define V_OSCK 26000000 /* Clock output from T2 */
++#define V_SCLK (V_OSCK >> 1)
++
++/* DDR type - Micron */
++#define CONFIG_OMAP3_MICRON_DDR 1
++
++#undef CONFIG_USE_IRQ /* no support for IRQs */
++#define CONFIG_MISC_INIT_R
++
++#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
++#define CONFIG_SETUP_MEMORY_TAGS 1
++#define CONFIG_INITRD_TAG 1
++#define CONFIG_REVISION_TAG 1
++#define CONFIG_SERIAL_TAG 1
++
++/* Size of malloc() pool */
++#define CONFIG_ENV_SIZE (128 << 10) /* Total Size Environment */
++ /* Sector */
++#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (512 << 10))
++#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
++ /* initial data */
++/* NS16550 Configuration */
++#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
++
++#define CONFIG_SYS_NS16550
++#define CONFIG_SYS_NS16550_SERIAL
++#define CONFIG_SYS_NS16550_REG_SIZE (-4)
++#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
++
++/* serial console configuration */
++#define CONFIG_CONS_INDEX 3
++#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
++#define CONFIG_SERIAL3 3 /* UART3 */
++
++/* allow to overwrite serial and ethaddr */
++#define CONFIG_ENV_OVERWRITE
++#define CONFIG_BAUDRATE 115200
++#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
++ 115200}
++#define CONFIG_MMC 1
++#define CONFIG_OMAP3_MMC 1
++#define CONFIG_SYS_MMC_MAX_DEVICE 1
++#define CONFIG_DOS_PARTITION 1
++
++/* commands to include */
++#include <config_cmd_default.h>
++
++#define CONFIG_CMD_EXT2 /* EXT2 Support */
++#define CONFIG_CMD_FAT /* FAT support */
++#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
++#define CONFIG_CMD_YAFFS2 /* YAFFS2 Support */
++#define CONFIG_CMD_UBI /* UBI Support */
++#define CONFIG_CMD_MTDPARTS
++
++#define CONFIG_CMD_I2C /* I2C serial bus support */
++#define CONFIG_CMD_MMC /* MMC support */
++#define CONFIG_CMD_NAND /* NAND support */
++#define CONFIG_CMD_DHCP
++#define CONFIG_CMD_PING
++
++#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
++#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
++#undef CONFIG_CMD_IMLS /* List all found images */
++
++#define CONFIG_SYS_NO_FLASH
++
++/* I2C */
++#define CONFIG_SYS_I2C_SPEED 100000
++#define CONFIG_SYS_I2C_SLAVE 1
++#define CONFIG_SYS_I2C_BUS 0
++#define CONFIG_SYS_I2C_BUS_SELECT 1
++#define CONFIG_DRIVER_OMAP34XX_I2C 1
++
++/* TWL4030 */
++#define CONFIG_TWL4030_POWER 1
++
++/* Board NAND Info. */
++#define CONFIG_NAND_OMAP_GPMC 1
++#define GPMC_NAND_ECC_LP_x8_LAYOUT 1
++#define OMAP34XX_GPMC_NAND_SMNAND 1
++
++#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
++ /* to access nand */
++#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
++ /* to access */
++ /* nand at CS0 */
++
++#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
++ /* NAND devices */
++#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
++
++/* JFFS2 */
++#define CONFIG_JFFS2_NAND
++#define CONFIG_JFFS2_DEV "nand0"
++#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
++ CONFIG_SYS_MAX_NAND_DEVICE)
++#define CONFIG_SYS_JFFS2_MEM_NAND
++#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
++#define CONFIG_SYS_JFFS2_NUM_BANKS 1
++
++/* ubi/ubifs related definitions */
++#define CONFIG_RBTREE
++#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
++#define CONFIG_MTD_PARTITIONS
++
++/* Environment information */
++#define CONFIG_BOOTDELAY 3
++
++#define CONFIG_BOOTFILE uImage
++
++#define CONFIG_EXTRA_ENV_SETTINGS \
++ "loadaddr=0x82000000\0" \
++ "baudrate=115200\0"\
++ "console=ttyS2,115200n8\0" \
++ "autoload=no\0" \
++ "mmcargs=setenv bootargs console=${console} " \
++ "root=/dev/mmcblk0p2 rw " \
++ "rootfstype=ext3 rootwait\0" \
++ "nandargs=setenv bootargs console=${console} " \
++ "root=/dev/mtdblock4 rw " \
++ "rootfstype=jffs2\0" \
++ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
++ "bootscript=echo Running bootscript from mmc ...; " \
++ "source ${loadaddr}\0" \
++ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
++ "mmcboot=echo Booting from mmc ...; " \
++ "run mmcargs; " \
++ "bootm ${loadaddr}\0" \
++ "nandboot=echo Booting from nand ...; " \
++ "run nandargs; " \
++ "onenand read ${loadaddr} 280000 400000; " \
++ "bootm ${loadaddr}\0" \
++
++#define CONFIG_BOOTCOMMAND \
++ "if mmc init; then " \
++ "if run loadbootscript; then " \
++ "run bootscript; " \
++ "else " \
++ "if run loaduimage; then " \
++ "run mmcboot; " \
++ "else run nandboot; " \
++ "fi; " \
++ "fi; " \
++ "else run nandboot; fi"
++
++#define MTDIDS_DEFAULT "nand0=nand"
++#define MTDPARTS_DEFAULT "mtdparts=nand:512k(xloader)," \
++ "1920k(u-boot)," \
++ "256k(env)," \
++ "4m(kernel)," \
++ "-(fs),"
++
++#define CONFIG_AUTO_COMPLETE 1
++/*
++ * Miscellaneous configurable options
++ */
++#define CONFIG_API 1
++#define V_PROMPT "CM-T35 # "
++
++#define CONFIG_SYS_LONGHELP /* undef to save memory */
++#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
++#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
++#define CONFIG_SYS_PROMPT V_PROMPT
++#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
++
++/* Print Buffer Size */
++#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
++ sizeof(CONFIG_SYS_PROMPT) + 16)
++#define CONFIG_SYS_MAXARGS 16 /* max number of command */
++ /* args */
++/* Boot Argument Buffer Size */
++#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
++
++/* memtest works on */
++#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x01000000)
++#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + 0x08000000)
++
++#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
++ /* address */
++
++/*
++ * OMAP3 has 12 GP timers, they can be driven by the system clock
++ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
++ * This rate is divided by a local divisor.
++ */
++#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
++#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
++#define CONFIG_SYS_HZ 1000
++
++/*
++ * Stack sizes
++ *
++ * The stack sizes are set up in start.S using the settings below
++ */
++#define CONFIG_STACKSIZE (128 << 10) /* regular stack */
++#ifdef CONFIG_USE_IRQ
++#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack */
++#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack */
++#endif
++
++/* Physical Memory Map */
++#define CONFIG_NR_DRAM_BANKS 1 /* CS1 may not be populated on CM-T35 */
++#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
++#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 meg */
++
++/* SDRAM Bank Allocation method */
++#define SDRC_R_B_C 1
++
++/* PISMO support */
++#define PISMO1_NAND_SIZE GPMC_SIZE_128M
++
++/* environment */
++#define CONFIG_ENV_IS_IN_NAND 1
++#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
++#define CONFIG_SYS_ENV_SECT_SIZE (1 << 128)
++#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
++
++/* SMSC9220 Ethernet */
++#if defined(CONFIG_CMD_NET)
++#define CONFIG_NET_MULTI
++#define CONFIG_SMC911X
++#define CONFIG_SMC911X_32_BIT
++#define CONFIG_SMC911X_KEEP_MAC
++#define CM_T35_SMC911X_BASE 0x2C000000
++#define SB_T35_SMC911X_BASE (CM_T35_SMC911X_BASE + (16 << 20))
++#define CONFIG_SMC911X_BASE CM_T35_SMC911X_BASE /* for smc911x_eeprom */
++#endif /* (CONFIG_CMD_NET) */
++
++#define CONFIG_OMAP3_GPIO_6 1
++
++#endif /* __CONFIG_H */
+diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
+index bd5037e..bac5127 100644
+--- a/include/configs/devkit8000.h
++++ b/include/configs/devkit8000.h
+@@ -293,15 +293,6 @@
+ #define CONFIG_ENV_IS_IN_NAND 1
+ #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+
+-#define CONFIG_ENV_OFFSET boot_flash_off
+-
+-#ifndef __ASSEMBLY__
+-extern struct gpmc *gpmc_cfg;
+-extern unsigned int boot_flash_base;
+-extern volatile unsigned int boot_flash_env_addr;
+-extern unsigned int boot_flash_off;
+-extern unsigned int boot_flash_sec;
+-extern unsigned int boot_flash_type;
+-#endif
++#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+
+ #endif /* __CONFIG_H */
+diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
+index 19a5ec9..73ead6c 100644
+--- a/include/configs/omap3_beagle.h
++++ b/include/configs/omap3_beagle.h
+@@ -291,8 +291,8 @@
+ #define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
+ #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+
+-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+-#define CONFIG_ENV_OFFSET boot_flash_off
++#define CONFIG_SYS_ENV_SECT_SIZE (1 << 128)
++#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+ #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+ /*-----------------------------------------------------------------------
+@@ -310,13 +310,4 @@
+ #define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+ #define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+-#ifndef __ASSEMBLY__
+-extern struct gpmc *gpmc_cfg;
+-extern unsigned int boot_flash_base;
+-extern volatile unsigned int boot_flash_env_addr;
+-extern unsigned int boot_flash_off;
+-extern unsigned int boot_flash_sec;
+-extern unsigned int boot_flash_type;
+-#endif
+-
+ #endif /* __CONFIG_H */
+diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
+index a5514ae..70eb86b 100644
+--- a/include/configs/omap3_evm.h
++++ b/include/configs/omap3_evm.h
+@@ -262,7 +262,7 @@
+ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+ #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
+
+-#define CONFIG_SYS_FLASH_BASE boot_flash_base
++#define CONFIG_SYS_FLASH_BASE ONENAND_MAP
+
+ /* Monitor at start of flash */
+ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+@@ -272,9 +272,9 @@
+ #define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
+ #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+
+-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+-#define CONFIG_ENV_OFFSET boot_flash_off
+-#define CONFIG_ENV_ADDR boot_flash_env_addr
++#define CONFIG_SYS_ENV_SECT_SIZE (1 << 128)
++#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET
++#define CONFIG_ENV_ADDR ONENAND_ENV_OFFSET
+
+ /*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+@@ -291,15 +291,6 @@
+ #define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+ #define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+-#ifndef __ASSEMBLY__
+-extern struct gpmc *gpmc_cfg;
+-extern unsigned int boot_flash_base;
+-extern volatile unsigned int boot_flash_env_addr;
+-extern unsigned int boot_flash_off;
+-extern unsigned int boot_flash_sec;
+-extern unsigned int boot_flash_type;
+-#endif
+-
+ /*----------------------------------------------------------------------------
+ * SMSC9115 Ethernet from SMSC9118 family
+ *----------------------------------------------------------------------------
+diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
+index ffb515d..6ffae60 100644
+--- a/include/configs/omap3_overo.h
++++ b/include/configs/omap3_overo.h
+@@ -266,7 +266,7 @@
+ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+ #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
+
+-#define CONFIG_SYS_FLASH_BASE boot_flash_base
++#define CONFIG_SYS_FLASH_BASE NAND_BASE
+
+ /* Monitor at start of flash */
+ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+@@ -276,8 +276,8 @@
+ #define ONENAND_ENV_OFFSET 0x240000 /* environment starts here */
+ #define SMNAND_ENV_OFFSET 0x240000 /* environment starts here */
+
+-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+-#define CONFIG_ENV_OFFSET boot_flash_off
++#define CONFIG_SYS_ENV_SECT_SIZE (1 << 128)
++#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+ #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+ /*-----------------------------------------------------------------------
+@@ -295,15 +295,6 @@
+ #define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+ #define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+-#ifndef __ASSEMBLY__
+-extern struct gpmc *gpmc_cfg;
+-extern unsigned int boot_flash_base;
+-extern volatile unsigned int boot_flash_env_addr;
+-extern unsigned int boot_flash_off;
+-extern unsigned int boot_flash_sec;
+-extern unsigned int boot_flash_type;
+-#endif
+-
+ #if defined(CONFIG_CMD_NET)
+ /*----------------------------------------------------------------------------
+ * SMSC9211 Ethernet from SMSC9118 family
+diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
+index 6f21af3..041412e 100644
+--- a/include/configs/omap3_pandora.h
++++ b/include/configs/omap3_pandora.h
+@@ -259,7 +259,7 @@
+ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+ #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
+
+-#define CONFIG_SYS_FLASH_BASE boot_flash_base
++#define CONFIG_SYS_FLASH_BASE ONENAND_MAP
+
+ /* Monitor at start of flash */
+ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+@@ -269,8 +269,8 @@
+ #define ONENAND_ENV_OFFSET 0x240000 /* environment starts here */
+ #define SMNAND_ENV_OFFSET 0x240000 /* environment starts here */
+
+-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+-#define CONFIG_ENV_OFFSET boot_flash_off
++#define CONFIG_SYS_ENV_SECT_SIZE (1 << 128)
++#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+ #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+ /*-----------------------------------------------------------------------
+@@ -288,13 +288,4 @@
+ #define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+ #define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+-#ifndef __ASSEMBLY__
+-extern struct gpmc *gpmc_cfg;
+-extern unsigned int boot_flash_base;
+-extern volatile unsigned int boot_flash_env_addr;
+-extern unsigned int boot_flash_off;
+-extern unsigned int boot_flash_sec;
+-extern unsigned int boot_flash_type;
+-#endif
+-
+ #endif /* __CONFIG_H */
+diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h
+index 229dc5e..3ec7ce0 100644
+--- a/include/configs/omap3_sdp3430.h
++++ b/include/configs/omap3_sdp3430.h
+@@ -355,15 +355,4 @@
+ * - rest for filesystem
+ */
+
+-/*--------------------------------------------------------------------------*/
+-
+-#ifndef __ASSEMBLY__
+-extern struct gpmc *gpmc_cfg;
+-extern unsigned int boot_flash_base;
+-extern volatile unsigned int boot_flash_env_addr;
+-extern unsigned int boot_flash_off;
+-extern unsigned int boot_flash_sec;
+-extern unsigned int boot_flash_type;
+-#endif
+-
+ #endif /* __CONFIG_H */
+diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
+index da4b677..9811f15 100644
+--- a/include/configs/omap3_zoom1.h
++++ b/include/configs/omap3_zoom1.h
+@@ -267,7 +267,7 @@
+ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+ #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
+
+-#define CONFIG_SYS_FLASH_BASE boot_flash_base
++#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_NAND_BASE
+
+ /* Monitor at start of flash */
+ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+@@ -277,8 +277,8 @@
+ #define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
+ #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+
+-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+-#define CONFIG_ENV_OFFSET boot_flash_off
++#define CONFIG_SYS_ENV_SECT_SIZE (1 << 128)
++#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+ #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+ /*-----------------------------------------------------------------------
+@@ -296,13 +296,4 @@
+ #define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+ #define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+-#ifndef __ASSEMBLY__
+-extern struct gpmc *gpmc_cfg;
+-extern unsigned int boot_flash_base;
+-extern volatile unsigned int boot_flash_env_addr;
+-extern unsigned int boot_flash_off;
+-extern unsigned int boot_flash_sec;
+-extern unsigned int boot_flash_type;
+-#endif
+-
+ #endif /* __CONFIG_H */
+diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h
+index 32cd6fd..1a23acd 100644
+--- a/include/configs/omap3_zoom2.h
++++ b/include/configs/omap3_zoom2.h
+@@ -232,7 +232,7 @@
+ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+ #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
+
+-#define CONFIG_SYS_FLASH_BASE boot_flash_base
++#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_NAND_BASE
+
+ /* Monitor at start of flash */
+ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+@@ -240,8 +240,8 @@
+ #define CONFIG_ENV_IS_IN_NAND 1
+ #define SMNAND_ENV_OFFSET 0x0c0000 /* environment starts here */
+
+-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+-#define CONFIG_ENV_OFFSET boot_flash_off
++#define CONFIG_SYS_ENV_SECT_SIZE (1 << 128)
++#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+ #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+ /*-----------------------------------------------------------------------
+@@ -251,13 +251,4 @@
+ #define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+ #define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+-#ifndef __ASSEMBLY__
+-extern struct gpmc *gpmc_cfg;
+-extern unsigned int boot_flash_base;
+-extern volatile unsigned int boot_flash_env_addr;
+-extern unsigned int boot_flash_off;
+-extern unsigned int boot_flash_sec;
+-extern unsigned int boot_flash_type;
+-#endif
+-
+ #endif /* __CONFIG_H */
diff --git a/recipes/u-boot/u-boot_git.bb b/recipes/u-boot/u-boot_git.bb
index e914d78..5fcf7c5 100644
--- a/recipes/u-boot/u-boot_git.bb
+++ b/recipes/u-boot/u-boot_git.bb
@@ -11,8 +11,10 @@ SRCREV_c7x0 = "9bf86baaa3b35b25baa2d664e2f7f6cafad689ee"
SRCREV_afeb9260 = "6b8edfde22acc574b5532e9f086e6a7287a9bc78"
SRCREV_afeb9260-180 = "6b8edfde22acc574b5532e9f086e6a7287a9bc78"
SRCREV_palmpre = "6b8edfde22acc574b5532e9f086e6a7287a9bc78"
+SRCREV_cm-t35 = "3c014f1586d5bfe30dca7549396915c83f31cd30"
SRC_URI_append_afeb9260 = " file://AFEB9260-network-fix.patch;patch=1"
SRC_URI_append_afeb9260-180 = " file://AFEB9260-network-fix.patch;patch=1"
+SRC_URI_append_cm-t35 = "file://cm-t35/cm-t35.patch;patch=1"
SRC_URI_beagleboard = "git://git.denx.de/u-boot-ti.git;protocol=git \
file://fw_env.config \
--
1.6.4.4
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 2/5] linux-omap 2.6.32: add cm-t35 support
2009-12-08 21:11 [PATCH 0/5] Add CM-T35 support Mike Rapoport
2009-12-08 21:11 ` [PATCH 1/5] u-boot git: add cm-t35 support Mike Rapoport
@ 2009-12-08 21:11 ` Mike Rapoport
2009-12-08 23:13 ` Koen Kooi
2009-12-08 21:11 ` [PATCH 3/5] cm-t35: add machine configuration Mike Rapoport
` (2 subsequent siblings)
4 siblings, 1 reply; 11+ messages in thread
From: Mike Rapoport @ 2009-12-08 21:11 UTC (permalink / raw)
To: openembedded-devel
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
---
.../0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch | 159 ++
...do24m-ensure-chip-select-changes-between-.patch | 30 +
...002-omap3-cm-t35-add-DSS2-display-support.patch | 307 ++++
...03-omap3-cm-t35-update-defconfig-for-DSS2.patch | 145 ++
.../0004-omap3-cm-t35-add-cm-t35-mux-configs.patch | 427 +++++
.../0006-omap3-cm-t35-update-defconfig.patch | 87 +
recipes/linux/linux-omap-2.6.32/cm-t35/defconfig | 1823 ++++++++++++++++++++
recipes/linux/linux-omap_2.6.32.bb | 12 +-
8 files changed, 2989 insertions(+), 1 deletions(-)
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0001-backlight-tdo24m-ensure-chip-select-changes-between-.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0002-omap3-cm-t35-add-DSS2-display-support.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0003-omap3-cm-t35-update-defconfig-for-DSS2.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0004-omap3-cm-t35-add-cm-t35-mux-configs.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/0006-omap3-cm-t35-update-defconfig.patch
create mode 100644 recipes/linux/linux-omap-2.6.32/cm-t35/defconfig
diff --git a/recipes/linux/linux-omap-2.6.32/cm-t35/0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch b/recipes/linux/linux-omap-2.6.32/cm-t35/0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch
new file mode 100644
index 0000000..423b29f
--- /dev/null
+++ b/recipes/linux/linux-omap-2.6.32/cm-t35/0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch
@@ -0,0 +1,159 @@
+From 971595be3dc245cfa095747263b94535d27a3f1c Mon Sep 17 00:00:00 2001
+From: Mike Rapoport <mike@compulab.co.il>
+Date: Tue, 1 Dec 2009 12:14:10 +0200
+Subject: [PATCH 1/6] OMAP: DSS2: add Toppoly TDO35S panel
+
+Signed-off-by: Mike Rapoport <mike@compulab.co.il>
+---
+ drivers/video/omap2/displays/Kconfig | 6 +
+ drivers/video/omap2/displays/Makefile | 1 +
+ .../video/omap2/displays/panel-toppoly-tdo35s.c | 112 ++++++++++++++++++++
+ 3 files changed, 119 insertions(+), 0 deletions(-)
+ create mode 100644 drivers/video/omap2/displays/panel-toppoly-tdo35s.c
+
+diff --git a/drivers/video/omap2/displays/Kconfig b/drivers/video/omap2/displays/Kconfig
+index 79d2861..0d0d4f3 100644
+--- a/drivers/video/omap2/displays/Kconfig
++++ b/drivers/video/omap2/displays/Kconfig
+@@ -25,4 +25,10 @@ config PANEL_TAAL
+ help
+ Taal DSI command mode panel from TPO.
+
++config PANEL_TOPPOLY_TDO35S
++ tristate "Toppoly TDO35S LCD Panel support"
++ depends on OMAP2_DSS
++ help
++ LCD Panel used in CM-T35
++
+ endmenu
+diff --git a/drivers/video/omap2/displays/Makefile b/drivers/video/omap2/displays/Makefile
+index d44e765..e299454 100644
+--- a/drivers/video/omap2/displays/Makefile
++++ b/drivers/video/omap2/displays/Makefile
+@@ -3,3 +3,4 @@ obj-$(CONFIG_PANEL_SAMSUNG_LTE430WQ_F0C) += panel-samsung-lte430wq-f0c.o
+ obj-$(CONFIG_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o
+
+ obj-$(CONFIG_PANEL_TAAL) += panel-taal.o
++obj-$(CONFIG_PANEL_TOPPOLY_TDO35S) += panel-toppoly-tdo35s.o
+\ No newline at end of file
+diff --git a/drivers/video/omap2/displays/panel-toppoly-tdo35s.c b/drivers/video/omap2/displays/panel-toppoly-tdo35s.c
+new file mode 100644
+index 0000000..e744b8c
+--- /dev/null
++++ b/drivers/video/omap2/displays/panel-toppoly-tdo35s.c
+@@ -0,0 +1,112 @@
++/*
++ * LCD panel driver for Toppoly TDO35S
++ *
++ * Copyright (C) 2009 CompuLab, Ltd.
++ * Author: Mike Rapoport <mike@compulab.co.il>
++ *
++ * Based on generic panel support
++ * Copyright (C) 2008 Nokia Corporation
++ * Author: Tomi Valkeinen <tomi.valkeinen@nokia.com>
++ *
++ * This program is free software; you can redistribute it and/or modify it
++ * under the terms of the GNU General Public License version 2 as published by
++ * the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful, but WITHOUT
++ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
++ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
++ * more details.
++ *
++ * You should have received a copy of the GNU General Public License along with
++ * this program. If not, see <http://www.gnu.org/licenses/>.
++ */
++
++#include <linux/module.h>
++#include <linux/delay.h>
++
++#include <plat/display.h>
++
++static struct omap_video_timings toppoly_tdo_panel_timings = {
++ /* 640 x 480 @ 60 Hz Reduced blanking VESA CVT 0.31M3-R */
++ .x_res = 480,
++ .y_res = 640,
++
++ .pixel_clock = 26000,
++
++ .hfp = 104,
++ .hsw = 8,
++ .hbp = 8,
++
++ .vfp = 4,
++ .vsw = 2,
++ .vbp = 2,
++};
++
++static int toppoly_tdo_panel_probe(struct omap_dss_device *dssdev)
++{
++ dssdev->panel.config = OMAP_DSS_LCD_TFT | OMAP_DSS_LCD_IVS |
++ OMAP_DSS_LCD_IHS;
++ dssdev->panel.timings = toppoly_tdo_panel_timings;
++
++ return 0;
++}
++
++static void toppoly_tdo_panel_remove(struct omap_dss_device *dssdev)
++{
++}
++
++static int toppoly_tdo_panel_enable(struct omap_dss_device *dssdev)
++{
++ int r = 0;
++
++ if (dssdev->platform_enable)
++ r = dssdev->platform_enable(dssdev);
++
++ return r;
++}
++
++static void toppoly_tdo_panel_disable(struct omap_dss_device *dssdev)
++{
++ if (dssdev->platform_disable)
++ dssdev->platform_disable(dssdev);
++}
++
++static int toppoly_tdo_panel_suspend(struct omap_dss_device *dssdev)
++{
++ toppoly_tdo_panel_disable(dssdev);
++ return 0;
++}
++
++static int toppoly_tdo_panel_resume(struct omap_dss_device *dssdev)
++{
++ return toppoly_tdo_panel_enable(dssdev);
++}
++
++static struct omap_dss_driver generic_driver = {
++ .probe = toppoly_tdo_panel_probe,
++ .remove = toppoly_tdo_panel_remove,
++
++ .enable = toppoly_tdo_panel_enable,
++ .disable = toppoly_tdo_panel_disable,
++ .suspend = toppoly_tdo_panel_suspend,
++ .resume = toppoly_tdo_panel_resume,
++
++ .driver = {
++ .name = "toppoly_tdo35s_panel",
++ .owner = THIS_MODULE,
++ },
++};
++
++static int __init toppoly_tdo_panel_drv_init(void)
++{
++ return omap_dss_register_driver(&generic_driver);
++}
++
++static void __exit toppoly_tdo_panel_drv_exit(void)
++{
++ omap_dss_unregister_driver(&generic_driver);
++}
++
++module_init(toppoly_tdo_panel_drv_init);
++module_exit(toppoly_tdo_panel_drv_exit);
++MODULE_LICENSE("GPL");
+--
+1.6.4.4
+
diff --git a/recipes/linux/linux-omap-2.6.32/cm-t35/0001-backlight-tdo24m-ensure-chip-select-changes-between-.patch b/recipes/linux/linux-omap-2.6.32/cm-t35/0001-backlight-tdo24m-ensure-chip-select-changes-between-.patch
new file mode 100644
index 0000000..b540987
--- /dev/null
+++ b/recipes/linux/linux-omap-2.6.32/cm-t35/0001-backlight-tdo24m-ensure-chip-select-changes-between-.patch
@@ -0,0 +1,30 @@
+From 8a2cbbaa60ea06370d2a6d9303b1aab54cdb8a69 Mon Sep 17 00:00:00 2001
+From: Mike Rapoport <mike@compulab.co.il>
+Date: Tue, 24 Nov 2009 10:09:35 +0200
+Subject: [PATCH] backlight: tdo24m: ensure chip select changes between transfers
+
+Some SPI host drivers do not change chip select betwen transfers unless
+.cs_chnage field is explicitly set. The LCD spec requires chip select
+change between consecuitive transfers, so ensure it at the SPI driver
+level.
+
+Signed-off-by: Mike Rapoport <mike@compulab.co.il>
+---
+ drivers/video/backlight/tdo24m.c | 1 +
+ 1 files changed, 1 insertions(+), 0 deletions(-)
+
+diff --git a/drivers/video/backlight/tdo24m.c b/drivers/video/backlight/tdo24m.c
+index bbfb502..4a3d46e 100644
+--- a/drivers/video/backlight/tdo24m.c
++++ b/drivers/video/backlight/tdo24m.c
+@@ -367,6 +367,7 @@ static int __devinit tdo24m_probe(struct spi_device *spi)
+
+ spi_message_init(m);
+
++ x->cs_change = 1;
+ x->tx_buf = &lcd->buf[0];
+ spi_message_add_tail(x, m);
+
+--
+1.6.4.4
+
diff --git a/recipes/linux/linux-omap-2.6.32/cm-t35/0002-omap3-cm-t35-add-DSS2-display-support.patch b/recipes/linux/linux-omap-2.6.32/cm-t35/0002-omap3-cm-t35-add-DSS2-display-support.patch
new file mode 100644
index 0000000..199e89b
--- /dev/null
+++ b/recipes/linux/linux-omap-2.6.32/cm-t35/0002-omap3-cm-t35-add-DSS2-display-support.patch
@@ -0,0 +1,307 @@
+From 7d601fa33c5475bcd3035df797a3cbe40cc542d4 Mon Sep 17 00:00:00 2001
+From: Mike Rapoport <mike@compulab.co.il>
+Date: Tue, 1 Dec 2009 13:09:28 +0200
+Subject: [PATCH 2/6] omap3: cm-t35: add DSS2 display support
+
+Signed-off-by: Mike Rapoport <mike@compulab.co.il>
+---
+ arch/arm/mach-omap2/board-cm-t35.c | 234 +++++++++++++++++++++++++++++++++++-
+ 1 files changed, 233 insertions(+), 1 deletions(-)
+
+diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
+index 22c4529..2d7a819 100644
+--- a/arch/arm/mach-omap2/board-cm-t35.c
++++ b/arch/arm/mach-omap2/board-cm-t35.c
+@@ -32,6 +32,9 @@
+ #include <linux/i2c/twl4030.h>
+ #include <linux/regulator/machine.h>
+
++#include <linux/spi/spi.h>
++#include <linux/spi/tdo24m.h>
++
+ #include <asm/mach-types.h>
+ #include <asm/mach/arch.h>
+ #include <asm/mach/map.h>
+@@ -42,6 +45,7 @@
+ #include <plat/nand.h>
+ #include <plat/gpmc.h>
+ #include <plat/usb.h>
++#include <plat/display.h>
+
+ #include <mach/hardware.h>
+
+@@ -248,7 +252,6 @@ static inline void cm_t35_init_nand(void) {}
+
+ #if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
+ defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+-#include <linux/spi/spi.h>
+ #include <linux/spi/ads7846.h>
+
+ #include <plat/mcspi.h>
+@@ -304,6 +307,193 @@ static void __init cm_t35_init_ads7846(void)
+ static inline void cm_t35_init_ads7846(void) {}
+ #endif
+
++#define CM_T35_LCD_EN_GPIO 157
++#define CM_T35_LCD_BL_GPIO 58
++#define CM_T35_DVI_EN_GPIO 54
++
++static int lcd_bl_gpio;
++static int lcd_en_gpio;
++static int dvi_en_gpio;
++
++static int lcd_enabled;
++static int dvi_enabled;
++
++static int cm_t35_panel_enable_lcd(struct omap_dss_device *dssdev)
++{
++ if (dvi_enabled) {
++ printk(KERN_ERR "cannot enable LCD, DVI is enabled\n");
++ return -EINVAL;
++ }
++
++ gpio_set_value(lcd_en_gpio, 1);
++ gpio_set_value(lcd_bl_gpio, 1);
++
++ lcd_enabled = 1;
++
++ return 0;
++}
++
++static void cm_t35_panel_disable_lcd(struct omap_dss_device *dssdev)
++{
++ lcd_enabled = 0;
++
++ gpio_set_value(lcd_bl_gpio, 0);
++ gpio_set_value(lcd_en_gpio, 0);
++}
++
++static int cm_t35_panel_enable_dvi(struct omap_dss_device *dssdev)
++{
++ if (lcd_enabled) {
++ printk(KERN_ERR "cannot enable DVI, LCD is enabled\n");
++ return -EINVAL;
++ }
++
++ gpio_set_value(dvi_en_gpio, 0);
++ dvi_enabled = 1;
++
++ return 0;
++}
++
++static void cm_t35_panel_disable_dvi(struct omap_dss_device *dssdev)
++{
++ gpio_set_value(dvi_en_gpio, 1);
++ dvi_enabled = 0;
++}
++
++static int cm_t35_panel_enable_tv(struct omap_dss_device *dssdev)
++{
++ return 0;
++}
++
++static void cm_t35_panel_disable_tv(struct omap_dss_device *dssdev)
++{
++}
++
++static struct omap_dss_device cm_t35_lcd_device = {
++ .name = "lcd",
++ .driver_name = "toppoly_tdo35s_panel",
++ .type = OMAP_DISPLAY_TYPE_DPI,
++ .phy.dpi.data_lines = 18,
++ .platform_enable = cm_t35_panel_enable_lcd,
++ .platform_disable = cm_t35_panel_disable_lcd,
++};
++
++static struct omap_dss_device cm_t35_dvi_device = {
++ .name = "dvi",
++ .driver_name = "generic_panel",
++ .type = OMAP_DISPLAY_TYPE_DPI,
++ .phy.dpi.data_lines = 24,
++ .platform_enable = cm_t35_panel_enable_dvi,
++ .platform_disable = cm_t35_panel_disable_dvi,
++};
++
++static struct omap_dss_device cm_t35_tv_device = {
++ .name = "tv",
++ .driver_name = "venc",
++ .type = OMAP_DISPLAY_TYPE_VENC,
++ .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
++ .platform_enable = cm_t35_panel_enable_tv,
++ .platform_disable = cm_t35_panel_disable_tv,
++};
++
++static struct omap_dss_device *cm_t35_dss_devices[] = {
++ &cm_t35_lcd_device,
++ &cm_t35_dvi_device,
++ &cm_t35_tv_device,
++};
++
++static struct omap_dss_board_info cm_t35_dss_data = {
++ .num_devices = ARRAY_SIZE(cm_t35_dss_devices),
++ .devices = cm_t35_dss_devices,
++ .default_device = &cm_t35_dvi_device,
++};
++
++static struct platform_device cm_t35_dss_device = {
++ .name = "omapdss",
++ .id = -1,
++ .dev = {
++ .platform_data = &cm_t35_dss_data,
++ },
++};
++
++static struct omap2_mcspi_device_config tdo24m_mcspi_config = {
++ .turbo_mode = 0,
++ .single_channel = 1, /* 0: slave, 1: master */
++};
++
++static struct tdo24m_platform_data tdo24m_config = {
++ .model = TDO35S,
++};
++
++static struct spi_board_info cm_t35_lcd_spi_board_info[] __initdata = {
++ {
++ .modalias = "tdo24m",
++ .bus_num = 4,
++ .chip_select = 0,
++ .max_speed_hz = 1000000,
++ .controller_data = &tdo24m_mcspi_config,
++ .platform_data = &tdo24m_config,
++ },
++};
++
++static void __init cm_t35_display_init(void)
++{
++ int err;
++
++ lcd_en_gpio = CM_T35_LCD_EN_GPIO;
++ lcd_bl_gpio = CM_T35_LCD_BL_GPIO;
++ dvi_en_gpio = CM_T35_DVI_EN_GPIO;
++
++ spi_register_board_info(cm_t35_lcd_spi_board_info,
++ ARRAY_SIZE(cm_t35_lcd_spi_board_info));
++
++ err = gpio_request(lcd_en_gpio, "LCD RST");
++ if (err) {
++ pr_err("CM-T35: failed to get LCD reset GPIO\n");
++ goto out;
++ }
++
++ err = gpio_request(lcd_bl_gpio, "LCD BL");
++ if (err) {
++ pr_err("CM-T35: failed to get LCD backlight control GPIO\n");
++ goto err_lcd_bl;
++ }
++
++ err = gpio_request(dvi_en_gpio, "DVI EN");
++ if (err) {
++ pr_err("CM-T35: failed to get DVI reset GPIO\n");
++ goto err_dvi_en;
++ }
++
++ gpio_export(lcd_en_gpio, 0);
++ gpio_export(lcd_bl_gpio, 0);
++ gpio_export(dvi_en_gpio, 0);
++ gpio_direction_output(lcd_en_gpio, 0);
++ gpio_direction_output(lcd_bl_gpio, 0);
++ gpio_direction_output(dvi_en_gpio, 1);
++
++ msleep(50);
++ gpio_set_value(lcd_en_gpio, 1);
++
++ err = platform_device_register(&cm_t35_dss_device);
++ if (err) {
++ pr_err("CM-T35: failed to register DSS device\n");
++ goto err_dev_reg;
++ }
++
++ return;
++
++err_dev_reg:
++ gpio_free(dvi_en_gpio);
++err_dvi_en:
++ gpio_free(lcd_bl_gpio);
++err_lcd_bl:
++ gpio_free(lcd_en_gpio);
++out:
++
++ return;
++}
++
+ static struct regulator_consumer_supply cm_t35_vmmc1_supply = {
+ .supply = "vmmc",
+ };
+@@ -312,6 +502,16 @@ static struct regulator_consumer_supply cm_t35_vsim_supply = {
+ .supply = "vmmc_aux",
+ };
+
++static struct regulator_consumer_supply cm_t35_vdac_supply = {
++ .supply = "vdda_dac",
++ .dev = &cm_t35_dss_device.dev,
++};
++
++static struct regulator_consumer_supply cm_t35_vdvi_supply = {
++ .supply = "vdvi",
++ .dev = &cm_t35_dss_device.dev,
++};
++
+ /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+ static struct regulator_init_data cm_t35_vmmc1 = {
+ .constraints = {
+@@ -342,6 +542,35 @@ static struct regulator_init_data cm_t35_vsim = {
+ .consumer_supplies = &cm_t35_vsim_supply,
+ };
+
++/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
++static struct regulator_init_data cm_t35_vdac = {
++ .constraints = {
++ .min_uV = 1800000,
++ .max_uV = 1800000,
++ .valid_modes_mask = REGULATOR_MODE_NORMAL
++ | REGULATOR_MODE_STANDBY,
++ .valid_ops_mask = REGULATOR_CHANGE_MODE
++ | REGULATOR_CHANGE_STATUS,
++ },
++ .num_consumer_supplies = 1,
++ .consumer_supplies = &cm_t35_vdac_supply,
++};
++
++/* VPLL2 for digital video outputs */
++static struct regulator_init_data cm_t35_vpll2 = {
++ .constraints = {
++ .name = "VDVI",
++ .min_uV = 1800000,
++ .max_uV = 1800000,
++ .valid_modes_mask = REGULATOR_MODE_NORMAL
++ | REGULATOR_MODE_STANDBY,
++ .valid_ops_mask = REGULATOR_CHANGE_MODE
++ | REGULATOR_CHANGE_STATUS,
++ },
++ .num_consumer_supplies = 1,
++ .consumer_supplies = &cm_t35_vdvi_supply,
++};
++
+ static struct twl4030_usb_data cm_t35_usb_data = {
+ .usb_mode = T2_USB_MODE_ULPI,
+ };
+@@ -445,6 +674,8 @@ static struct twl4030_platform_data cm_t35_twldata = {
+ .gpio = &cm_t35_gpio_data,
+ .vmmc1 = &cm_t35_vmmc1,
+ .vsim = &cm_t35_vsim,
++ .vdac = &cm_t35_vdac,
++ .vpll2 = &cm_t35_vpll2,
+ };
+
+ static struct i2c_board_info __initdata cm_t35_i2c_boardinfo[] = {
+@@ -490,6 +721,7 @@ static void __init cm_t35_init(void)
+ cm_t35_init_ads7846();
+ cm_t35_init_ethernet();
+ cm_t35_init_led();
++ cm_t35_display_init();
+
+ usb_musb_init();
+
+--
+1.6.4.4
+
diff --git a/recipes/linux/linux-omap-2.6.32/cm-t35/0003-omap3-cm-t35-update-defconfig-for-DSS2.patch b/recipes/linux/linux-omap-2.6.32/cm-t35/0003-omap3-cm-t35-update-defconfig-for-DSS2.patch
new file mode 100644
index 0000000..dc1e527
--- /dev/null
+++ b/recipes/linux/linux-omap-2.6.32/cm-t35/0003-omap3-cm-t35-update-defconfig-for-DSS2.patch
@@ -0,0 +1,145 @@
+From 10cd78db62cbda2f9db1c53d459ee03a35b84662 Mon Sep 17 00:00:00 2001
+From: Mike Rapoport <mike@compulab.co.il>
+Date: Tue, 1 Dec 2009 13:16:02 +0200
+Subject: [PATCH 3/6] omap3: cm-t35: update defconfig for DSS2
+
+Signed-off-by: Mike Rapoport <mike@compulab.co.il>
+---
+ arch/arm/configs/cm_t35_defconfig | 82 +++++++++++++++++++++++++++++++++++--
+ 1 files changed, 78 insertions(+), 4 deletions(-)
+
+diff --git a/arch/arm/configs/cm_t35_defconfig b/arch/arm/configs/cm_t35_defconfig
+index e42c5c8..bd6f882 100644
+--- a/arch/arm/configs/cm_t35_defconfig
++++ b/arch/arm/configs/cm_t35_defconfig
+@@ -1,7 +1,7 @@
+ #
+ # Automatically generated make config: don't edit
+-# Linux kernel version: 2.6.32-rc4
+-# Tue Oct 13 17:10:40 2009
++# Linux kernel version: 2.6.32-rc8
++# Tue Dec 1 12:08:44 2009
+ #
+ CONFIG_ARM=y
+ CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+@@ -215,6 +215,7 @@ CONFIG_OMAP_DM_TIMER=y
+ # CONFIG_OMAP_LL_DEBUG_UART1 is not set
+ # CONFIG_OMAP_LL_DEBUG_UART2 is not set
+ CONFIG_OMAP_LL_DEBUG_UART3=y
++# CONFIG_OMAP_LL_DEBUG_NONE is not set
+ # CONFIG_OMAP_PM_NONE is not set
+ CONFIG_OMAP_PM_NOOP=y
+ CONFIG_ARCH_OMAP34XX=y
+@@ -227,11 +228,15 @@ CONFIG_ARCH_OMAP3430=y
+ # CONFIG_MACH_OMAP_LDP is not set
+ # CONFIG_MACH_OVERO is not set
+ # CONFIG_MACH_OMAP3EVM is not set
++# CONFIG_MACH_OMAP3517EVM is not set
+ # CONFIG_MACH_OMAP3_PANDORA is not set
+ # CONFIG_MACH_OMAP_3430SDP is not set
+ # CONFIG_MACH_NOKIA_RX51 is not set
+ # CONFIG_MACH_OMAP_ZOOM2 is not set
++# CONFIG_MACH_OMAP_ZOOM3 is not set
+ CONFIG_MACH_CM_T35=y
++# CONFIG_MACH_IGEP0020 is not set
++# CONFIG_MACH_OMAP_3630SDP is not set
+
+ #
+ # Processor Type
+@@ -963,6 +968,7 @@ CONFIG_SSB_POSSIBLE=y
+ # CONFIG_TPS65010 is not set
+ CONFIG_TWL4030_CORE=y
+ # CONFIG_TWL4030_POWER is not set
++# CONFIG_TWL4030_CODEC is not set
+ # CONFIG_MFD_TMIO is not set
+ # CONFIG_MFD_T7L66XB is not set
+ # CONFIG_MFD_TC6387XB is not set
+@@ -993,8 +999,66 @@ CONFIG_REGULATOR_TWL4030=y
+ #
+ # CONFIG_VGASTATE is not set
+ # CONFIG_VIDEO_OUTPUT_CONTROL is not set
+-# CONFIG_FB is not set
+-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
++CONFIG_FB=y
++# CONFIG_FIRMWARE_EDID is not set
++# CONFIG_FB_DDC is not set
++# CONFIG_FB_BOOT_VESA_SUPPORT is not set
++CONFIG_FB_CFB_FILLRECT=y
++CONFIG_FB_CFB_COPYAREA=y
++CONFIG_FB_CFB_IMAGEBLIT=y
++# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
++# CONFIG_FB_SYS_FILLRECT is not set
++# CONFIG_FB_SYS_COPYAREA is not set
++# CONFIG_FB_SYS_IMAGEBLIT is not set
++# CONFIG_FB_FOREIGN_ENDIAN is not set
++# CONFIG_FB_SYS_FOPS is not set
++# CONFIG_FB_SVGALIB is not set
++# CONFIG_FB_MACMODES is not set
++# CONFIG_FB_BACKLIGHT is not set
++# CONFIG_FB_MODE_HELPERS is not set
++# CONFIG_FB_TILEBLITTING is not set
++
++#
++# Frame buffer hardware drivers
++#
++# CONFIG_FB_S1D13XXX is not set
++# CONFIG_FB_VIRTUAL is not set
++# CONFIG_FB_METRONOME is not set
++# CONFIG_FB_MB862XX is not set
++# CONFIG_FB_BROADSHEET is not set
++# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set
++CONFIG_OMAP2_VRAM=y
++CONFIG_OMAP2_VRFB=y
++CONFIG_OMAP2_DSS=y
++CONFIG_OMAP2_VRAM_SIZE=4
++CONFIG_OMAP2_DSS_DEBUG_SUPPORT=y
++# CONFIG_OMAP2_DSS_RFBI is not set
++CONFIG_OMAP2_DSS_VENC=y
++# CONFIG_OMAP2_DSS_SDI is not set
++# CONFIG_OMAP2_DSS_DSI is not set
++# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set
++CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=0
++CONFIG_FB_OMAP2=y
++CONFIG_FB_OMAP2_DEBUG_SUPPORT=y
++# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set
++CONFIG_FB_OMAP2_NUM_FBS=3
++
++#
++# OMAP2/3 Display Device Drivers
++#
++CONFIG_PANEL_GENERIC=y
++# CONFIG_PANEL_SAMSUNG_LTE430WQ_F0C is not set
++# CONFIG_PANEL_SHARP_LS037V7DW01 is not set
++CONFIG_PANEL_TOPPOLY_TDO35S=y
++CONFIG_BACKLIGHT_LCD_SUPPORT=y
++CONFIG_LCD_CLASS_DEVICE=y
++# CONFIG_LCD_LMS283GF05 is not set
++# CONFIG_LCD_LTV350QV is not set
++# CONFIG_LCD_ILI9320 is not set
++CONFIG_LCD_TDO24M=y
++# CONFIG_LCD_VGG2432A4 is not set
++# CONFIG_LCD_PLATFORM is not set
++# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+
+ #
+ # Display device support
+@@ -1006,6 +1070,16 @@ CONFIG_REGULATOR_TWL4030=y
+ #
+ # CONFIG_VGA_CONSOLE is not set
+ CONFIG_DUMMY_CONSOLE=y
++CONFIG_FRAMEBUFFER_CONSOLE=y
++# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
++# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
++# CONFIG_FONTS is not set
++CONFIG_FONT_8x8=y
++CONFIG_FONT_8x16=y
++CONFIG_LOGO=y
++CONFIG_LOGO_LINUX_MONO=y
++CONFIG_LOGO_LINUX_VGA16=y
++CONFIG_LOGO_LINUX_CLUT224=y
+ # CONFIG_SOUND is not set
+ CONFIG_HID_SUPPORT=y
+ CONFIG_HID=y
+--
+1.6.4.4
+
diff --git a/recipes/linux/linux-omap-2.6.32/cm-t35/0004-omap3-cm-t35-add-cm-t35-mux-configs.patch b/recipes/linux/linux-omap-2.6.32/cm-t35/0004-omap3-cm-t35-add-cm-t35-mux-configs.patch
new file mode 100644
index 0000000..ff8b50b
--- /dev/null
+++ b/recipes/linux/linux-omap-2.6.32/cm-t35/0004-omap3-cm-t35-add-cm-t35-mux-configs.patch
@@ -0,0 +1,427 @@
+From a1a572a6b020996155fa3fd7e70a96299b37cf30 Mon Sep 17 00:00:00 2001
+From: Mike Rapoport <mike@compulab.co.il>
+Date: Mon, 7 Dec 2009 10:27:48 +0200
+Subject: [PATCH 4/6] omap3: cm-t35: add cm-t35 mux configs
+
+Signed-off-by: Mike Rapoport <mike@compulab.co.il>
+---
+ arch/arm/mach-omap2/board-cm-t35.c | 94 +++++++++++++++++++
+ arch/arm/mach-omap2/mux.c | 158 ++++++++++++++++++++++++++++++++-
+ arch/arm/plat-omap/include/plat/mux.h | 86 ++++++++++++++++++
+ 3 files changed, 337 insertions(+), 1 deletions(-)
+
+diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
+index 2d7a819..3e54499 100644
+--- a/arch/arm/mach-omap2/board-cm-t35.c
++++ b/arch/arm/mach-omap2/board-cm-t35.c
+@@ -693,6 +693,99 @@ static void __init cm_t35_init_i2c(void)
+ ARRAY_SIZE(cm_t35_i2c_boardinfo));
+ }
+
++static void __init cm_t35_init_mux(void)
++{
++ /* nCS and IRQ mux for CM-T35 ethernet */
++ omap_cfg_reg(G5_34XX_GPMC_NCS5);
++ omap_cfg_reg(A23_34XX_GPIO163_UP);
++
++ /* nCS, IRQ and reset mux for SB-T35 ethernet */
++ omap_cfg_reg(F4_34XX_GPMC_NCS4);
++ omap_cfg_reg(N21_34XX_GPIO127_UP);
++ omap_cfg_reg(B23_34XX_GPIO164_OUT);
++
++ /* PENDOWN GPIO */
++ omap_cfg_reg(F3_34XX_GPIO57_UP);
++
++ /* mUSB */
++ omap_cfg_reg(R21_3430_USB0HS_PHY_CLK);
++ omap_cfg_reg(R23_3430_USB0HS_PHY_STP);
++ omap_cfg_reg(P23_3430_USB0HS_PHY_DIR);
++ omap_cfg_reg(R22_3430_USB0HS_PHY_NXT);
++ omap_cfg_reg(T24_3430_USB0HS_PHY_DATA0);
++ omap_cfg_reg(T23_3430_USB0HS_PHY_DATA1);
++ omap_cfg_reg(U24_3430_USB0HS_PHY_DATA2);
++ omap_cfg_reg(U23_3430_USB0HS_PHY_DATA3);
++ omap_cfg_reg(W24_3430_USB0HS_PHY_DATA4);
++ omap_cfg_reg(V23_3430_USB0HS_PHY_DATA5);
++ omap_cfg_reg(W23_3430_USB0HS_PHY_DATA6);
++ omap_cfg_reg(T22_3430_USB0HS_PHY_DATA7);
++
++ /* MMC 2 */
++ omap_cfg_reg(AB2_3430_MMC2_DIR_DAT0);
++ omap_cfg_reg(AA2_3430_MMC2_DIR_DAT1);
++ omap_cfg_reg(Y2_3430_MMC2_DIR_CMD);
++ omap_cfg_reg(AA1_3420_MMC2_CLKIN);
++
++ /* McSPI 1 */
++ omap_cfg_reg(T5_34XX_MCSPI1_CLK);
++ omap_cfg_reg(R4_34XX_MCSPI1_SIMO);
++ omap_cfg_reg(T4_34XX_MCSPI1_SOMI);
++ omap_cfg_reg(T6_34XX_MCSPI1_CS0);
++
++ /* McBSP 2 */
++ omap_cfg_reg(V20_34XX_MCBSP2_FSX);
++ omap_cfg_reg(T21_34XX_MCBSP2_CLKX);
++ omap_cfg_reg(V19_34XX_MCBSP2_DR);
++ omap_cfg_reg(R20_34XX_MCBSP2_DX);
++
++ omap_cfg_reg(F21_34XX_GPIO109_OUT);
++
++ /* serial ports */
++ omap_cfg_reg(W4_34XX_UART2_TX);
++ omap_cfg_reg(V4_34XX_UART2_RX);
++ omap_cfg_reg(W7_34XX_UART1_TX);
++ omap_cfg_reg(V7_34XX_UART1_RX);
++
++ /* display controls */
++ omap_cfg_reg(U8_34XX_GPIO54_OUT);
++ omap_cfg_reg(G4_34XX_GPIO58_OUT);
++/* omap_cfg_reg(??_34XX_GPIO129_OUT); */
++
++ /* DSS */
++ omap_cfg_reg(G22_34XX_DSS_PCLK);
++ omap_cfg_reg(E22_34XX_DSS_HSYNC);
++ omap_cfg_reg(F22_34XX_DSS_VSYNC);
++ omap_cfg_reg(J21_34XX_DSS_ACBIAS);
++ omap_cfg_reg(AC19_34XX_DSS_DATA0);
++ omap_cfg_reg(AB19_34XX_DSS_DATA1);
++ omap_cfg_reg(AD20_34XX_DSS_DATA2);
++ omap_cfg_reg(AC20_34XX_DSS_DATA3);
++ omap_cfg_reg(AD21_34XX_DSS_DATA4);
++ omap_cfg_reg(AC21_34XX_DSS_DATA5);
++ omap_cfg_reg(D24_34XX_DSS_DATA6);
++ omap_cfg_reg(E23_34XX_DSS_DATA7);
++ omap_cfg_reg(E24_34XX_DSS_DATA8);
++ omap_cfg_reg(F23_34XX_DSS_DATA9);
++ omap_cfg_reg(AC22_34XX_DSS_DATA10);
++ omap_cfg_reg(AC23_34XX_DSS_DATA11);
++ omap_cfg_reg(AB22_34XX_DSS_DATA12);
++ omap_cfg_reg(Y22_34XX_DSS_DATA13);
++ omap_cfg_reg(W22_34XX_DSS_DATA14);
++ omap_cfg_reg(V22_34XX_DSS_DATA15);
++ omap_cfg_reg(J22_34XX_DSS_DATA16);
++ omap_cfg_reg(G23_34XX_DSS_DATA17);
++ omap_cfg_reg(G24_34XX_DSS_DATA18);
++ omap_cfg_reg(H23_34XX_DSS_DATA19);
++ omap_cfg_reg(D23_34XX_DSS_DATA20);
++ omap_cfg_reg(K22_34XX_DSS_DATA21);
++ omap_cfg_reg(V21_34XX_DSS_DATA22);
++ omap_cfg_reg(W21_34XX_DSS_DATA23);
++
++ /* TPS IRQ */
++ omap_cfg_reg(AF26_34XX_SYS_NIRQ);
++}
++
+ static struct omap_board_config_kernel cm_t35_config[] __initdata = {
+ };
+
+@@ -716,6 +809,7 @@ static void __init cm_t35_map_io(void)
+ static void __init cm_t35_init(void)
+ {
+ omap_serial_init();
++ cm_t35_init_mux();
+ cm_t35_init_i2c();
+ cm_t35_init_nand();
+ cm_t35_init_ads7846();
+diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
+index c18a94e..23eb011 100644
+--- a/arch/arm/mach-omap2/mux.c
++++ b/arch/arm/mach-omap2/mux.c
+@@ -279,6 +279,33 @@ MUX_CFG_34XX("AD26_34XX_I2C4_SCL", 0xa00,
+ MUX_CFG_34XX("AE26_34XX_I2C4_SDA", 0xa02,
+ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+
++/* HSUSB Port 0 */
++MUX_CFG_34XX("R21_3430_USB0HS_PHY_CLK", 0x1a2,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("R23_3430_USB0HS_PHY_STP", 0x1a4,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT | \
++ OMAP2_PULL_ENA | OMAP2_PULL_UP)
++MUX_CFG_34XX("P23_3430_USB0HS_PHY_DIR", 0x1a6,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("R22_3430_USB0HS_PHY_NXT", 0x1a8,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("T24_3430_USB0HS_PHY_DATA0", 0x1aa,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("T23_3430_USB0HS_PHY_DATA1", 0x1ac,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("U24_3430_USB0HS_PHY_DATA2", 0x1ae,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("U23_3430_USB0HS_PHY_DATA3", 0x1b0,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("W24_3430_USB0HS_PHY_DATA4", 0x1b2,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("V23_3430_USB0HS_PHY_DATA5", 0x1b4,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("W23_3430_USB0HS_PHY_DATA6", 0x1b6,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("T22_3430_USB0HS_PHY_DATA7", 0x1b8,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++
+ /* PHY - HSUSB: 12-pin ULPI PHY: Port 1*/
+ MUX_CFG_34XX("Y8_3430_USB1HS_PHY_CLK", 0x5da,
+ OMAP34XX_MUX_MODE3 | OMAP34XX_PIN_OUTPUT)
+@@ -541,6 +568,15 @@ MUX_CFG_34XX("AF3_3430_MMC2_DAT6", 0x168,
+ MUX_CFG_34XX("AE3_3430_MMC2_DAT7", 0x16A,
+ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+
++MUX_CFG_34XX("AB2_3430_MMC2_DIR_DAT0", 0x164,
++ OMAP34XX_MUX_MODE1 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AA2_3430_MMC2_DIR_DAT1", 0x166,
++ OMAP34XX_MUX_MODE1 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("Y2_3430_MMC2_DIR_CMD", 0x168,
++ OMAP34XX_MUX_MODE1 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AA1_3420_MMC2_CLKIN", 0x16a,
++ OMAP34XX_MUX_MODE1 | OMAP34XX_PIN_INPUT)
++
+ /* MMC3 */
+ MUX_CFG_34XX("AF10_3430_MMC3_CLK", 0x5d8,
+ OMAP34XX_MUX_MODE2 | OMAP34XX_PIN_INPUT_PULLUP)
+@@ -559,13 +595,133 @@ MUX_CFG_34XX("AF13_3430_MMC3_DAT3", 0x5e2,
+ MUX_CFG_34XX("AF26_34XX_SYS_NIRQ", 0x1E0,
+ OMAP3_WAKEUP_EN | OMAP34XX_PIN_INPUT_PULLUP |
+ OMAP34XX_MUX_MODE0)
+-/* EHCI GPIO's on OMAP3EVM (Rev >= E) */
++
+ MUX_CFG_34XX("AH14_34XX_GPIO21", 0x5ea,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLUP)
+ MUX_CFG_34XX("AF9_34XX_GPIO22", 0x5ec,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLUP)
+ MUX_CFG_34XX("U3_34XX_GPIO61", 0x0c8,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLUP)
++
++MUX_CFG_34XX("AG4_34XX_GPIO134", 0x160,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("U8_34XX_GPIO54", 0x0b4,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AE4_34XX_GPIO136", 0x164,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("F3_34XX_GPIO57_UP", 0x0ba,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLUP)
++MUX_CFG_34XX("G4_34XX_GPIO58_OUT", 0x0bc,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("W2_34XX_GPIO59", 0x0be,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("L1_34XX_GPIO61_OUT", 0x0c8,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("C2_34XX_GPIO65", 0x0d2,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("N21_34XX_GPIO127_UP", 0x152,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLUP)
++MUX_CFG_34XX("A23_34XX_GPIO163_UP", 0x19a,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLUP)
++MUX_CFG_34XX("B23_34XX_GPIO164_OUT", 0x19c,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AA6_34XX_GPIO164_OUT", 0x1e2,
++ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
++
++/* GPMC */
++MUX_CFG_34XX("F4_34XX_GPMC_NCS4", 0x0b6, OMAP34XX_MUX_MODE0)
++MUX_CFG_34XX("G5_34XX_GPMC_NCS5", 0x0b8, OMAP34XX_MUX_MODE0)
++
++/* McSPI 1 */
++MUX_CFG_34XX("T5_34XX_MCSPI1_CLK", 0x1c8,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("R4_34XX_MCSPI1_SIMO", 0x1ca,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("T4_34XX_MCSPI1_SOMI", 0x1cc,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("T6_34XX_MCSPI1_CS0", 0x1ce,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLDOWN)
++
++/* McBSP 2 */
++MUX_CFG_34XX("V20_34XX_MCBSP2_FSX", 0x13c,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("T21_34XX_MCBSP2_CLKX", 0x13e,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("V19_34XX_MCBSP2_DR", 0x140,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("R20_34XX_MCBSP2_DX", 0x142,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++
++MUX_CFG_34XX("F21_34XX_GPIO109_OUT", 0x12a,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++
++/* Serial ports */
++MUX_CFG_34XX("W4_34XX_UART2_TX", 0x170,
++ OMAP34XX_MUX_MODE1 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("V4_34XX_UART2_RX", 0x172,
++ OMAP34XX_MUX_MODE1 | OMAP34XX_PIN_INPUT)
++MUX_CFG_34XX("W7_34XX_UART1_TX", 0x17c,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("V7_34XX_UART1_RX", 0x182,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT)
++
++/* DSS */
++MUX_CFG_34XX("G22_34XX_DSS_PCLK", 0x0d4,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("E22_34XX_DSS_HSYNC", 0x0d6,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("F22_34XX_DSS_VSYNC", 0x0d8,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("J21_34XX_DSS_ACBIAS", 0x0da,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AC19_34XX_DSS_DATA0", 0x0dc,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AB19_34XX_DSS_DATA1", 0x0de,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AD20_34XX_DSS_DATA2", 0x0e0,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AC20_34XX_DSS_DATA3", 0x0e2,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AD21_34XX_DSS_DATA4", 0x0e4,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AC21_34XX_DSS_DATA5", 0x0e6,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("D24_34XX_DSS_DATA6", 0x0e8,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("E23_34XX_DSS_DATA7", 0x0ea,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("E24_34XX_DSS_DATA8", 0x0ec,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("F23_34XX_DSS_DATA9", 0x0ee,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AC22_34XX_DSS_DATA10", 0x0f0,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AC23_34XX_DSS_DATA11", 0x0f2,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("AB22_34XX_DSS_DATA12", 0x0f4,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("Y22_34XX_DSS_DATA13", 0x0f6,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("W22_34XX_DSS_DATA14", 0x0f8,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("V22_34XX_DSS_DATA15", 0x0fa,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("J22_34XX_DSS_DATA16", 0x0fc,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("G23_34XX_DSS_DATA17", 0x0fe,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("G24_34XX_DSS_DATA18", 0x100,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("H23_34XX_DSS_DATA19", 0x102,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("D23_34XX_DSS_DATA20", 0x104,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("K22_34XX_DSS_DATA21", 0x106,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("V21_34XX_DSS_DATA22", 0x108,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
++MUX_CFG_34XX("W21_34XX_DSS_DATA23", 0x10a,
++ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
+ };
+
+ #define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins)
+diff --git a/arch/arm/plat-omap/include/plat/mux.h b/arch/arm/plat-omap/include/plat/mux.h
+index ba77de6..119379c 100644
+--- a/arch/arm/plat-omap/include/plat/mux.h
++++ b/arch/arm/plat-omap/include/plat/mux.h
+@@ -692,6 +692,20 @@ enum omap34xx_index {
+ AD26_34XX_I2C4_SCL,
+ AE26_34XX_I2C4_SDA,
+
++ /* HSUSB Port 0 */
++ R21_3430_USB0HS_PHY_CLK,
++ R23_3430_USB0HS_PHY_STP,
++ P23_3430_USB0HS_PHY_DIR,
++ R22_3430_USB0HS_PHY_NXT,
++ T24_3430_USB0HS_PHY_DATA0,
++ T23_3430_USB0HS_PHY_DATA1,
++ U24_3430_USB0HS_PHY_DATA2,
++ U23_3430_USB0HS_PHY_DATA3,
++ W24_3430_USB0HS_PHY_DATA4,
++ V23_3430_USB0HS_PHY_DATA5,
++ W23_3430_USB0HS_PHY_DATA6,
++ T22_3430_USB0HS_PHY_DATA7,
++
+ /* PHY - HSUSB: 12-pin ULPI PHY: Port 1*/
+ Y8_3430_USB1HS_PHY_CLK,
+ Y9_3430_USB1HS_PHY_STP,
+@@ -839,6 +853,11 @@ enum omap34xx_index {
+ AF3_3430_MMC2_DAT6,
+ AE3_3430_MMC2_DAT7,
+
++ AB2_3430_MMC2_DIR_DAT0,
++ AA2_3430_MMC2_DIR_DAT1,
++ Y2_3430_MMC2_DIR_CMD,
++ AA1_3420_MMC2_CLKIN,
++
+ /* MMC3 */
+ AF10_3430_MMC3_CLK,
+ AC3_3430_MMC3_CMD,
+@@ -854,6 +873,73 @@ enum omap34xx_index {
+ AH14_34XX_GPIO21,
+ AF9_34XX_GPIO22,
+ U3_34XX_GPIO61,
++
++ AG4_34XX_GPIO134,
++ U8_34XX_GPIO54,
++ AE4_34XX_GPIO136,
++ F3_34XX_GPIO57_UP,
++ G4_34XX_GPIO58_OUT,
++ W2_34XX_GPIO59,
++ L1_34XX_GPIO61_OUT,
++ C2_34XX_GPIO65,
++ N21_34XX_GPIO127_UP,
++ A23_34XX_GPIO163_UP,
++ B23_34XX_GPIO164_OUT,
++ AA6_34XX_GPIO186_OUT,
++
++ /* gpmc */
++ F4_34XX_GPMC_NCS4,
++ G5_34XX_GPMC_NCS5,
++
++ /* McSPI 1 */
++ T5_34XX_MCSPI1_CLK,
++ R4_34XX_MCSPI1_SIMO,
++ T4_34XX_MCSPI1_SOMI,
++ T6_34XX_MCSPI1_CS0,
++
++ /* McBSP 2 */
++ V20_34XX_MCBSP2_FSX,
++ T21_34XX_MCBSP2_CLKX,
++ V19_34XX_MCBSP2_DR,
++ R20_34XX_MCBSP2_DX,
++
++ F21_34XX_GPIO109_OUT,
++
++ /* serial ports */
++ W4_34XX_UART2_TX,
++ V4_34XX_UART2_RX,
++ W7_34XX_UART1_TX,
++ V7_34XX_UART1_RX,
++
++ /* DSS */
++ G22_34XX_DSS_PCLK,
++ E22_34XX_DSS_HSYNC,
++ F22_34XX_DSS_VSYNC,
++ J21_34XX_DSS_ACBIAS,
++ AC19_34XX_DSS_DATA0,
++ AB19_34XX_DSS_DATA1,
++ AD20_34XX_DSS_DATA2,
++ AC20_34XX_DSS_DATA3,
++ AD21_34XX_DSS_DATA4,
++ AC21_34XX_DSS_DATA5,
++ D24_34XX_DSS_DATA6,
++ E23_34XX_DSS_DATA7,
++ E24_34XX_DSS_DATA8,
++ F23_34XX_DSS_DATA9,
++ AC22_34XX_DSS_DATA10,
++ AC23_34XX_DSS_DATA11,
++ AB22_34XX_DSS_DATA12,
++ Y22_34XX_DSS_DATA13,
++ W22_34XX_DSS_DATA14,
++ V22_34XX_DSS_DATA15,
++ J22_34XX_DSS_DATA16,
++ G23_34XX_DSS_DATA17,
++ G24_34XX_DSS_DATA18,
++ H23_34XX_DSS_DATA19,
++ D23_34XX_DSS_DATA20,
++ K22_34XX_DSS_DATA21,
++ V21_34XX_DSS_DATA22,
++ W21_34XX_DSS_DATA23,
+ };
+
+ struct omap_mux_cfg {
+--
+1.6.4.4
+
diff --git a/recipes/linux/linux-omap-2.6.32/cm-t35/0006-omap3-cm-t35-update-defconfig.patch b/recipes/linux/linux-omap-2.6.32/cm-t35/0006-omap3-cm-t35-update-defconfig.patch
new file mode 100644
index 0000000..a9034f0
--- /dev/null
+++ b/recipes/linux/linux-omap-2.6.32/cm-t35/0006-omap3-cm-t35-update-defconfig.patch
@@ -0,0 +1,87 @@
+From 88f7dc4c115c57b12de7ab4170bdaaeba145283b Mon Sep 17 00:00:00 2001
+From: Mike Rapoport <mike@compulab.co.il>
+Date: Mon, 7 Dec 2009 11:07:55 +0200
+Subject: [PATCH 6/6] omap3: cm-t35: update defconfig
+
+Signed-off-by: Mike Rapoport <mike@compulab.co.il>
+---
+ arch/arm/configs/cm_t35_defconfig | 28 ++++++++++++++++++++++------
+ 1 files changed, 22 insertions(+), 6 deletions(-)
+
+diff --git a/arch/arm/configs/cm_t35_defconfig b/arch/arm/configs/cm_t35_defconfig
+index bd6f882..78eeb66 100644
+--- a/arch/arm/configs/cm_t35_defconfig
++++ b/arch/arm/configs/cm_t35_defconfig
+@@ -1,7 +1,7 @@
+ #
+ # Automatically generated make config: don't edit
+-# Linux kernel version: 2.6.32-rc8
+-# Tue Dec 1 12:08:44 2009
++# Linux kernel version: 2.6.32
++# Mon Dec 7 10:43:46 2009
+ #
+ CONFIG_ARM=y
+ CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+@@ -572,7 +572,15 @@ CONFIG_MTD_NAND_IDS=y
+ #
+ # UBI - Unsorted block images
+ #
+-# CONFIG_MTD_UBI is not set
++CONFIG_MTD_UBI=y
++CONFIG_MTD_UBI_WL_THRESHOLD=4096
++CONFIG_MTD_UBI_BEB_RESERVE=1
++# CONFIG_MTD_UBI_GLUEBI is not set
++
++#
++# UBI debugging options
++#
++# CONFIG_MTD_UBI_DEBUG is not set
+ # CONFIG_PARPORT is not set
+ CONFIG_BLK_DEV=y
+ # CONFIG_BLK_DEV_COW_COMMON is not set
+@@ -1506,6 +1514,12 @@ CONFIG_JFFS2_RTIME=y
+ CONFIG_JFFS2_CMODE_PRIORITY=y
+ # CONFIG_JFFS2_CMODE_SIZE is not set
+ # CONFIG_JFFS2_CMODE_FAVOURLZO is not set
++CONFIG_UBIFS_FS=y
++# CONFIG_UBIFS_FS_XATTR is not set
++# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
++CONFIG_UBIFS_FS_LZO=y
++CONFIG_UBIFS_FS_ZLIB=y
++# CONFIG_UBIFS_FS_DEBUG is not set
+ # CONFIG_CRAMFS is not set
+ # CONFIG_SQUASHFS is not set
+ # CONFIG_VXFS_FS is not set
+@@ -1775,9 +1789,9 @@ CONFIG_CRYPTO_DES=y
+ #
+ # Compression
+ #
+-# CONFIG_CRYPTO_DEFLATE is not set
++CONFIG_CRYPTO_DEFLATE=y
+ # CONFIG_CRYPTO_ZLIB is not set
+-# CONFIG_CRYPTO_LZO is not set
++CONFIG_CRYPTO_LZO=y
+
+ #
+ # Random Number Generation
+@@ -1792,7 +1806,7 @@ CONFIG_CRYPTO_HW=y
+ CONFIG_BITREVERSE=y
+ CONFIG_GENERIC_FIND_LAST_BIT=y
+ CONFIG_CRC_CCITT=y
+-# CONFIG_CRC16 is not set
++CONFIG_CRC16=y
+ # CONFIG_CRC_T10DIF is not set
+ # CONFIG_CRC_ITU_T is not set
+ CONFIG_CRC32=y
+@@ -1800,6 +1814,8 @@ CONFIG_CRC32=y
+ CONFIG_LIBCRC32C=y
+ CONFIG_ZLIB_INFLATE=y
+ CONFIG_ZLIB_DEFLATE=y
++CONFIG_LZO_COMPRESS=y
++CONFIG_LZO_DECOMPRESS=y
+ CONFIG_DECOMPRESS_GZIP=y
+ CONFIG_HAS_IOMEM=y
+ CONFIG_HAS_IOPORT=y
+--
+1.6.4.4
+
diff --git a/recipes/linux/linux-omap-2.6.32/cm-t35/defconfig b/recipes/linux/linux-omap-2.6.32/cm-t35/defconfig
new file mode 100644
index 0000000..78eeb66
--- /dev/null
+++ b/recipes/linux/linux-omap-2.6.32/cm-t35/defconfig
@@ -0,0 +1,1823 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.32
+# Mon Dec 7 10:43:46 2009
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_HAS_CPUFREQ=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=17
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+CONFIG_KALLSYMS_EXTRA_PASS=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Kernel Performance Events And Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_MODVERSIONS=y
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_FREEZER=y
+
+#
+# System Type
+#
+CONFIG_MMU=y
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_NOMADIK is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+CONFIG_ARCH_OMAP=y
+# CONFIG_ARCH_BCMRING is not set
+
+#
+# TI OMAP Implementations
+#
+CONFIG_ARCH_OMAP_OTG=y
+# CONFIG_ARCH_OMAP1 is not set
+# CONFIG_ARCH_OMAP2 is not set
+CONFIG_ARCH_OMAP3=y
+# CONFIG_ARCH_OMAP4 is not set
+
+#
+# OMAP Feature Selections
+#
+# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set
+# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set
+CONFIG_OMAP_RESET_CLOCKS=y
+CONFIG_OMAP_MUX=y
+# CONFIG_OMAP_MUX_DEBUG is not set
+CONFIG_OMAP_MUX_WARNINGS=y
+CONFIG_OMAP_MCBSP=y
+# CONFIG_OMAP_MBOX_FWK is not set
+# CONFIG_OMAP_MPU_TIMER is not set
+CONFIG_OMAP_32K_TIMER=y
+CONFIG_OMAP_32K_TIMER_HZ=128
+CONFIG_OMAP_DM_TIMER=y
+# CONFIG_OMAP_LL_DEBUG_UART1 is not set
+# CONFIG_OMAP_LL_DEBUG_UART2 is not set
+CONFIG_OMAP_LL_DEBUG_UART3=y
+# CONFIG_OMAP_LL_DEBUG_NONE is not set
+# CONFIG_OMAP_PM_NONE is not set
+CONFIG_OMAP_PM_NOOP=y
+CONFIG_ARCH_OMAP34XX=y
+CONFIG_ARCH_OMAP3430=y
+
+#
+# OMAP Board Type
+#
+# CONFIG_MACH_OMAP3_BEAGLE is not set
+# CONFIG_MACH_OMAP_LDP is not set
+# CONFIG_MACH_OVERO is not set
+# CONFIG_MACH_OMAP3EVM is not set
+# CONFIG_MACH_OMAP3517EVM is not set
+# CONFIG_MACH_OMAP3_PANDORA is not set
+# CONFIG_MACH_OMAP_3430SDP is not set
+# CONFIG_MACH_NOKIA_RX51 is not set
+# CONFIG_MACH_OMAP_ZOOM2 is not set
+# CONFIG_MACH_OMAP_ZOOM3 is not set
+CONFIG_MACH_CM_T35=y
+# CONFIG_MACH_IGEP0020 is not set
+# CONFIG_MACH_OMAP_3630SDP is not set
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_V7=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_HAS_ASID=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_HAS_TLS_REG=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+# CONFIG_ARM_ERRATA_430973 is not set
+# CONFIG_ARM_ERRATA_458693 is not set
+# CONFIG_ARM_ERRATA_460075 is not set
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=128
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+# CONFIG_LEDS is not set
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE=""
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+CONFIG_VFP=y
+CONFIG_VFPv3=y
+CONFIG_NEON=y
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+CONFIG_BINFMT_MISC=y
+
+#
+# Power management options
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
+# CONFIG_PM_RUNTIME is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+CONFIG_WIRELESS=y
+# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
+# CONFIG_WIRELESS_OLD_REGULATORY is not set
+CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
+CONFIG_LIB80211=m
+# CONFIG_LIB80211_DEBUG is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=m
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_OMAP_NOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_OMAP2=y
+CONFIG_MTD_NAND_OMAP_PREFETCH=y
+# CONFIG_MTD_NAND_OMAP_PREFETCH_DMA is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=16384
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_NATIONAL_PHY is not set
+# CONFIG_STE10XP is not set
+# CONFIG_LSI_ET1011C_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+CONFIG_SMSC911X=y
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
+# CONFIG_KS8851_MLL is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_WLAN=y
+# CONFIG_WLAN_PRE80211 is not set
+CONFIG_WLAN_80211=y
+CONFIG_LIBERTAS=m
+# CONFIG_LIBERTAS_USB is not set
+CONFIG_LIBERTAS_SDIO=m
+# CONFIG_LIBERTAS_SPI is not set
+# CONFIG_LIBERTAS_DEBUG is not set
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_HOSTAP is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_QT2160 is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+CONFIG_KEYBOARD_TWL4030=m
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=m
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MCS5000 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=32
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_DETECT_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_OMAP=y
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_OMAP24XX=y
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+CONFIG_GPIO_TWL4030=y
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+CONFIG_OMAP_WATCHDOG=y
+# CONFIG_TWL4030_WATCHDOG is not set
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+CONFIG_TWL4030_CORE=y
+# CONFIG_TWL4030_POWER is not set
+# CONFIG_TWL4030_CODEC is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+CONFIG_REGULATOR=y
+# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+CONFIG_REGULATOR_TWL4030=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_REGULATOR_TPS65023 is not set
+# CONFIG_REGULATOR_TPS6507X is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set
+CONFIG_OMAP2_VRAM=y
+CONFIG_OMAP2_VRFB=y
+CONFIG_OMAP2_DSS=y
+CONFIG_OMAP2_VRAM_SIZE=4
+CONFIG_OMAP2_DSS_DEBUG_SUPPORT=y
+# CONFIG_OMAP2_DSS_RFBI is not set
+CONFIG_OMAP2_DSS_VENC=y
+# CONFIG_OMAP2_DSS_SDI is not set
+# CONFIG_OMAP2_DSS_DSI is not set
+# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set
+CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=0
+CONFIG_FB_OMAP2=y
+CONFIG_FB_OMAP2_DEBUG_SUPPORT=y
+# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set
+CONFIG_FB_OMAP2_NUM_FBS=3
+
+#
+# OMAP2/3 Display Device Drivers
+#
+CONFIG_PANEL_GENERIC=y
+# CONFIG_PANEL_SAMSUNG_LTE430WQ_F0C is not set
+# CONFIG_PANEL_SHARP_LS037V7DW01 is not set
+CONFIG_PANEL_TOPPOLY_TDO35S=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_LMS283GF05 is not set
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+CONFIG_LCD_TDO24M=y
+# CONFIG_LCD_VGG2432A4 is not set
+# CONFIG_LCD_PLATFORM is not set
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+# CONFIG_SOUND is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HIDRAW is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_HID_PID is not set
+# CONFIG_USB_HIDDEV is not set
+
+#
+# Special HID drivers
+#
+# CONFIG_HID_A4TECH is not set
+# CONFIG_HID_APPLE is not set
+# CONFIG_HID_BELKIN is not set
+# CONFIG_HID_CHERRY is not set
+# CONFIG_HID_CHICONY is not set
+# CONFIG_HID_CYPRESS is not set
+# CONFIG_HID_DRAGONRISE is not set
+# CONFIG_HID_EZKEY is not set
+# CONFIG_HID_KYE is not set
+# CONFIG_HID_GYRATION is not set
+# CONFIG_HID_TWINHAN is not set
+# CONFIG_HID_KENSINGTON is not set
+# CONFIG_HID_LOGITECH is not set
+# CONFIG_HID_MICROSOFT is not set
+# CONFIG_HID_MONTEREY is not set
+# CONFIG_HID_NTRIG is not set
+# CONFIG_HID_PANTHERLORD is not set
+# CONFIG_HID_PETALYNX is not set
+# CONFIG_HID_SAMSUNG is not set
+# CONFIG_HID_SONY is not set
+# CONFIG_HID_SUNPLUS is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
+# CONFIG_HID_TOPSEED is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_DEVICE_CLASS is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+CONFIG_USB_SUSPEND=y
+CONFIG_USB_OTG=y
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+CONFIG_USB_MON=y
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_OXU210HP_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
+# CONFIG_USB_OHCI_HCD is not set
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_SOC=y
+
+#
+# OMAP 343x high speed USB support
+#
+# CONFIG_USB_MUSB_HOST is not set
+# CONFIG_USB_MUSB_PERIPHERAL is not set
+CONFIG_USB_MUSB_OTG=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
+CONFIG_USB_MUSB_HDRC_HCD=y
+# CONFIG_MUSB_PIO_ONLY is not set
+CONFIG_USB_INVENTRA_DMA=y
+# CONFIG_USB_TI_CPPI_DMA is not set
+# CONFIG_USB_MUSB_DEBUG is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
+# CONFIG_USB_TMC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+
+#
+# also be needed; see USB_STORAGE Help for more info
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+CONFIG_USB_TEST=y
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG is not set
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+# CONFIG_USB_GADGET_DEBUG_FS is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_R8A66597 is not set
+# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
+# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+CONFIG_USB_GADGET_DUALSPEED=y
+# CONFIG_USB_ZERO is not set
+# CONFIG_USB_AUDIO is not set
+CONFIG_USB_ETH=y
+CONFIG_USB_ETH_RNDIS=y
+# CONFIG_USB_ETH_EEM is not set
+# CONFIG_USB_GADGETFS is not set
+# CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_G_SERIAL is not set
+# CONFIG_USB_MIDI_GADGET is not set
+# CONFIG_USB_G_PRINTER is not set
+# CONFIG_USB_CDC_COMPOSITE is not set
+
+#
+# OTG and related infrastructure
+#
+CONFIG_USB_OTG_UTILS=y
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_ISP1301_OMAP is not set
+CONFIG_TWL4030_USB=y
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_OMAP is not set
+CONFIG_MMC_OMAP_HS=y
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
+# CONFIG_MMC_SPI is not set
+# CONFIG_MEMSTICK is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP3944 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_BD2802 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+# CONFIG_LEDS_TRIGGER_TIMER is not set
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
+# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+CONFIG_RTC_DRV_TWL4030=y
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
+# CONFIG_STAGING is not set
+
+#
+# CBUS support
+#
+# CONFIG_CBUS is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+# CONFIG_EXT3_FS_XATTR is not set
+# CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_QUOTA=y
+# CONFIG_QUOTA_NETLINK_INTERFACE is not set
+CONFIG_PRINT_QUOTA_WARNING=y
+CONFIG_QUOTA_TREE=y
+# CONFIG_QFMT_V1 is not set
+CONFIG_QFMT_V2=y
+CONFIG_QUOTACTL=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+CONFIG_NTFS_FS=m
+# CONFIG_NTFS_DEBUG is not set
+# CONFIG_NTFS_RW is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+CONFIG_JFFS2_SUMMARY=y
+# CONFIG_JFFS2_FS_XATTR is not set
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_JFFS2_CMODE_NONE is not set
+CONFIG_JFFS2_CMODE_PRIORITY=y
+# CONFIG_JFFS2_CMODE_SIZE is not set
+# CONFIG_JFFS2_CMODE_FAVOURLZO is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_XATTR is not set
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+CONFIG_FTRACE=y
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_BOOT_TRACER is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_DYNAMIC_DEBUG is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+CONFIG_ARM_UNWIND=y
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+CONFIG_DEBUG_LL=y
+# CONFIG_DEBUG_ICEDCC is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_GHASH is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=y
+# CONFIG_CRYPTO_ZLIB is not set
+CONFIG_CRYPTO_LZO=y
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC16=y
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+CONFIG_LIBCRC32C=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
diff --git a/recipes/linux/linux-omap_2.6.32.bb b/recipes/linux/linux-omap_2.6.32.bb
index 95692c0..3caaaf4 100644
--- a/recipes/linux/linux-omap_2.6.32.bb
+++ b/recipes/linux/linux-omap_2.6.32.bb
@@ -3,9 +3,10 @@ require linux.inc
DESCRIPTION = "Linux kernel for OMAP processors"
KERNEL_IMAGETYPE = "uImage"
-COMPATIBLE_MACHINE = "omap5912osk|omap1710h3|omap2430sdp|omap2420h4|beagleboard|omap3evm|omap3-pandora|overo|omapzoom|omapzoom2|omap4430-sdp"
+COMPATIBLE_MACHINE = "omap5912osk|omap1710h3|omap2430sdp|omap2420h4|beagleboard|omap3evm|omap3-pandora|overo|omapzoom|omapzoom2|omap4430-sdp|cm-t35"
DEFAULT_PREFERENCE = "-1"
+DEFAULT_PREFERENCE_cm-t35 = "1"
SRCREV = "89c9eaeb92c97348dcabd6cb377b646c00855f6a"
@@ -23,6 +24,15 @@ file://usb/ehci-omap.c-mach-to-plat.diff;patch=1 \
SRC_URI_append_beagleboard = " file://logo_linux_clut224.ppm \
"
+SRC_URI_append_cm-t35 = " \
+file://cm-t35/0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch;patch=1 \
+file://cm-t35/0002-omap3-cm-t35-add-DSS2-display-support.patch;patch=1 \
+file://cm-t35/0003-omap3-cm-t35-update-defconfig-for-DSS2.patch;patch=1 \
+file://cm-t35/0004-omap3-cm-t35-add-cm-t35-mux-configs.patch;patch=1 \
+file://cm-t35/0006-omap3-cm-t35-update-defconfig.patch;patch=1 \
+file://cm-t35/0001-backlight-tdo24m-ensure-chip-select-changes-between-.patch;patch=1 \
+"
+
S = "${WORKDIR}/git"
module_autoload_ohci-hcd_omap5912osk = "ohci-hcd"
--
1.6.4.4
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 3/5] cm-t35: add machine configuration
2009-12-08 21:11 [PATCH 0/5] Add CM-T35 support Mike Rapoport
2009-12-08 21:11 ` [PATCH 1/5] u-boot git: add cm-t35 support Mike Rapoport
2009-12-08 21:11 ` [PATCH 2/5] linux-omap 2.6.32: " Mike Rapoport
@ 2009-12-08 21:11 ` Mike Rapoport
2009-12-08 23:10 ` Koen Kooi
2009-12-08 21:11 ` [PATCH 4/5] angstrom-led-config: Add LED setup for the cm-t35 and bump PR Mike Rapoport
2009-12-08 21:11 ` [PATCH 5/5] xserver-xorg-conf: add cm-t35 support Mike Rapoport
4 siblings, 1 reply; 11+ messages in thread
From: Mike Rapoport @ 2009-12-08 21:11 UTC (permalink / raw)
To: openembedded-devel
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
---
conf/machine/cm-t35.conf | 46 ++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 46 insertions(+), 0 deletions(-)
create mode 100644 conf/machine/cm-t35.conf
diff --git a/conf/machine/cm-t35.conf b/conf/machine/cm-t35.conf
new file mode 100644
index 0000000..15bb18b
--- /dev/null
+++ b/conf/machine/cm-t35.conf
@@ -0,0 +1,46 @@
+#@TYPE: Machine
+#@NAME: CM-T35 machine
+#@DESCRIPTION: Machine configuration for the CompuLab CM-T35 board (http://www.compulab.co.il/t3530/html/t3530-cm-datasheet.htm)
+
+TARGET_ARCH = "arm"
+
+PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
+XSERVER = "xserver-xorg \
+ xf86-input-evdev \
+ xf86-input-mouse \
+ xf86-input-evtouch \
+ xf86-input-tslib \
+ xf86-video-omapfb \
+ xf86-input-keyboard"
+
+GUI_MACHINE_CLASS = "bigscreen"
+
+require conf/machine/include/omap3.inc
+
+IMAGE_FSTYPES += "tar.bz2 ubi"
+EXTRA_IMAGECMD_jffs2 = "-lnp "
+
+# Guesswork
+SERIAL_CONSOLE = "115200 ttyS2"
+
+UBOOT_MACHINE = "cm_t35_config"
+PREFERRED_VERSION_u-boot = "git"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# From dmesg:
+# UBI: smallest flash I/O unit: 2048
+# UBI: logical eraseblock size: 126976 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 4039 LEBs
+MKUBIFS_ARGS = "-m 2048 -e 126976 -c 4039"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# from dmesg:
+# UBI: smallest flash I/O unit: 2048
+# UBI: physical eraseblock size: 131072 bytes (128 KiB)
+# UBI: sub-page size: 512
+UBINIZE_ARGS = "-O 2048 -m 2048 -p 128KiB"
+
+MACHINE_EXTRA_RRECOMMENDS = "omap3-sgx-modules marvell-sdio-fw"
+MACHINE_FEATURES = "kernel26 screen apm usbgadget usbhost vfat alsa wifi ext2"
+
--
1.6.4.4
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 4/5] angstrom-led-config: Add LED setup for the cm-t35 and bump PR.
2009-12-08 21:11 [PATCH 0/5] Add CM-T35 support Mike Rapoport
` (2 preceding siblings ...)
2009-12-08 21:11 ` [PATCH 3/5] cm-t35: add machine configuration Mike Rapoport
@ 2009-12-08 21:11 ` Mike Rapoport
2009-12-08 21:11 ` [PATCH 5/5] xserver-xorg-conf: add cm-t35 support Mike Rapoport
4 siblings, 0 replies; 11+ messages in thread
From: Mike Rapoport @ 2009-12-08 21:11 UTC (permalink / raw)
To: openembedded-devel
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
---
recipes/angstrom/angstrom-led-config.bb | 2 +-
recipes/angstrom/angstrom-led-config/cm-t35/leds | 2 ++
2 files changed, 3 insertions(+), 1 deletions(-)
create mode 100644 recipes/angstrom/angstrom-led-config/cm-t35/leds
diff --git a/recipes/angstrom/angstrom-led-config.bb b/recipes/angstrom/angstrom-led-config.bb
index 2dbfd01..a0373ed 100644
--- a/recipes/angstrom/angstrom-led-config.bb
+++ b/recipes/angstrom/angstrom-led-config.bb
@@ -1,7 +1,7 @@
DESCRIPTION = "Configuration files for runtime LED configuration"
#PV = "${DISTRO_VERSION}"
-PR = "r6"
+PR = "r7"
PACKAGE_ARCH = "${MACHINE_ARCH}"
inherit update-rc.d
diff --git a/recipes/angstrom/angstrom-led-config/cm-t35/leds b/recipes/angstrom/angstrom-led-config/cm-t35/leds
new file mode 100644
index 0000000..4d24396
--- /dev/null
+++ b/recipes/angstrom/angstrom-led-config/cm-t35/leds
@@ -0,0 +1,2 @@
+#file format: name trigger
+cm-t35:green heartbeat
--
1.6.4.4
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 5/5] xserver-xorg-conf: add cm-t35 support
2009-12-08 21:11 [PATCH 0/5] Add CM-T35 support Mike Rapoport
` (3 preceding siblings ...)
2009-12-08 21:11 ` [PATCH 4/5] angstrom-led-config: Add LED setup for the cm-t35 and bump PR Mike Rapoport
@ 2009-12-08 21:11 ` Mike Rapoport
4 siblings, 0 replies; 11+ messages in thread
From: Mike Rapoport @ 2009-12-08 21:11 UTC (permalink / raw)
To: openembedded-devel
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
---
.../xserver-xorg-conf/cm-t35/xorg.conf | 29 ++++++++++++++++++++
recipes/xorg-xserver/xserver-xorg-conf_0.1.bb | 2 +-
2 files changed, 30 insertions(+), 1 deletions(-)
create mode 100644 recipes/xorg-xserver/xserver-xorg-conf/cm-t35/xorg.conf
diff --git a/recipes/xorg-xserver/xserver-xorg-conf/cm-t35/xorg.conf b/recipes/xorg-xserver/xserver-xorg-conf/cm-t35/xorg.conf
new file mode 100644
index 0000000..07d849d
--- /dev/null
+++ b/recipes/xorg-xserver/xserver-xorg-conf/cm-t35/xorg.conf
@@ -0,0 +1,29 @@
+Section "Module"
+ Load "extmod"
+ Load "dbe"
+ Load "glx"
+ Load "freetype"
+ Load "type1"
+ Load "record"
+ Load "dri"
+EndSection
+
+Section "Monitor"
+ Identifier "Builtin Default Monitor"
+EndSection
+
+Section "Device"
+ Identifier "Builtin Default fbdev Device 0"
+ Driver "omapfb"
+EndSection
+
+Section "Screen"
+ Identifier "Builtin Default fbdev Screen 0"
+ Device "Builtin Default fbdev Device 0"
+ Monitor "Builtin Default Monitor"
+EndSection
+
+Section "ServerLayout"
+ Identifier "Builtin Default Layout"
+ Screen "Builtin Default fbdev Screen 0"
+EndSection
diff --git a/recipes/xorg-xserver/xserver-xorg-conf_0.1.bb b/recipes/xorg-xserver/xserver-xorg-conf_0.1.bb
index 8945e1e..77e0f8d 100644
--- a/recipes/xorg-xserver/xserver-xorg-conf_0.1.bb
+++ b/recipes/xorg-xserver/xserver-xorg-conf_0.1.bb
@@ -1,5 +1,5 @@
DESCRIPTION = "Machine specific xorg.conf files"
-PR = "r16"
+PR = "r17"
SRC_URI = "file://xorg.conf"
--
1.6.4.4
^ permalink raw reply related [flat|nested] 11+ messages in thread
* Re: [PATCH 3/5] cm-t35: add machine configuration
2009-12-08 21:11 ` [PATCH 3/5] cm-t35: add machine configuration Mike Rapoport
@ 2009-12-08 23:10 ` Koen Kooi
2009-12-09 7:01 ` Mike Rapoport
2009-12-09 9:16 ` Marcin Juszkiewicz
0 siblings, 2 replies; 11+ messages in thread
From: Koen Kooi @ 2009-12-08 23:10 UTC (permalink / raw)
To: openembedded-devel
On 08-12-09 22:11, Mike Rapoport wrote:
> Signed-off-by: Mike Rapoport<mike@compulab.co.il>
> +MACHINE_EXTRA_RRECOMMENDS = "omap3-sgx-modules marvell-sdio-fw"
The current sgx release and all the following ones will have
omap3-sgx-modules built directly from the .bin, so everyone building a
task-base based images will have to request that from TI. Do you really
want that?
regards,
Koen
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 2/5] linux-omap 2.6.32: add cm-t35 support
2009-12-08 21:11 ` [PATCH 2/5] linux-omap 2.6.32: " Mike Rapoport
@ 2009-12-08 23:13 ` Koen Kooi
2009-12-09 6:56 ` Mike Rapoport
0 siblings, 1 reply; 11+ messages in thread
From: Koen Kooi @ 2009-12-08 23:13 UTC (permalink / raw)
To: openembedded-devel
On 08-12-09 22:11, Mike Rapoport wrote:
> Signed-off-by: Mike Rapoport<mike@compulab.co.il>
> +SRC_URI_append_cm-t35 = " \
> +file://cm-t35/0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch;patch=1 \
> +file://cm-t35/0002-omap3-cm-t35-add-DSS2-display-support.patch;patch=1 \
> +file://cm-t35/0003-omap3-cm-t35-update-defconfig-for-DSS2.patch;patch=1 \
> +file://cm-t35/0004-omap3-cm-t35-add-cm-t35-mux-configs.patch;patch=1 \
> +file://cm-t35/0006-omap3-cm-t35-update-defconfig.patch;patch=1 \
> +file://cm-t35/0001-backlight-tdo24m-ensure-chip-select-changes-between-.patch;patch=1 \
> +"
> +
Could you make those patches non-machine specific? If you put them in
the main SRC_URI they stand a better change of being kept up to date.
I'm going to add a lot of patches to that recipe soon and I don't want
to break anything in the process.
regards,
Koen
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 2/5] linux-omap 2.6.32: add cm-t35 support
2009-12-08 23:13 ` Koen Kooi
@ 2009-12-09 6:56 ` Mike Rapoport
0 siblings, 0 replies; 11+ messages in thread
From: Mike Rapoport @ 2009-12-09 6:56 UTC (permalink / raw)
To: openembedded-devel
Koen Kooi wrote:
> On 08-12-09 22:11, Mike Rapoport wrote:
>> Signed-off-by: Mike Rapoport<mike@compulab.co.il>
>
>> +SRC_URI_append_cm-t35 = " \
>> +file://cm-t35/0001-OMAP-DSS2-add-Toppoly-TDO35S-panel.patch;patch=1 \
>> +file://cm-t35/0002-omap3-cm-t35-add-DSS2-display-support.patch;patch=1 \
>> +file://cm-t35/0003-omap3-cm-t35-update-defconfig-for-DSS2.patch;patch=1
>> \
>> +file://cm-t35/0004-omap3-cm-t35-add-cm-t35-mux-configs.patch;patch=1 \
>> +file://cm-t35/0006-omap3-cm-t35-update-defconfig.patch;patch=1 \
>> +file://cm-t35/0001-backlight-tdo24m-ensure-chip-select-changes-between-.patch;patch=1
>> \
>> +"
>> +
>
> Could you make those patches non-machine specific? If you put them in
> the main SRC_URI they stand a better change of being kept up to date.
> I'm going to add a lot of patches to that recipe soon and I don't want
> to break anything in the process.
Ok, will do.
> regards,
>
> Koen
>
>
> _______________________________________________
> Openembedded-devel mailing list
> Openembedded-devel@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel
>
--
Sincerely yours,
Mike.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 3/5] cm-t35: add machine configuration
2009-12-08 23:10 ` Koen Kooi
@ 2009-12-09 7:01 ` Mike Rapoport
2009-12-09 9:16 ` Marcin Juszkiewicz
1 sibling, 0 replies; 11+ messages in thread
From: Mike Rapoport @ 2009-12-09 7:01 UTC (permalink / raw)
To: openembedded-devel
Koen Kooi wrote:
> On 08-12-09 22:11, Mike Rapoport wrote:
>> Signed-off-by: Mike Rapoport<mike@compulab.co.il>
>
>> +MACHINE_EXTRA_RRECOMMENDS = "omap3-sgx-modules marvell-sdio-fw"
>
> The current sgx release and all the following ones will have
> omap3-sgx-modules built directly from the .bin, so everyone building a
> task-base based images will have to request that from TI. Do you really
> want that?
This is difficult to tell... I think for now I'll align cm-t35 with other omap3
machines.
> regards,
>
> Koen
>
>
> _______________________________________________
> Openembedded-devel mailing list
> Openembedded-devel@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel
>
--
Sincerely yours,
Mike.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 3/5] cm-t35: add machine configuration
2009-12-08 23:10 ` Koen Kooi
2009-12-09 7:01 ` Mike Rapoport
@ 2009-12-09 9:16 ` Marcin Juszkiewicz
1 sibling, 0 replies; 11+ messages in thread
From: Marcin Juszkiewicz @ 2009-12-09 9:16 UTC (permalink / raw)
To: openembedded-devel
Dnia środa, 9 grudnia 2009 o 00:10:51 Koen Kooi napisał(a):
> On 08-12-09 22:11, Mike Rapoport wrote:
> > Signed-off-by: Mike Rapoport<mike@compulab.co.il>
> >
> > +MACHINE_EXTRA_RRECOMMENDS = "omap3-sgx-modules marvell-sdio-fw"
>
> The current sgx release and all the following ones will have
> omap3-sgx-modules built directly from the .bin, so everyone building a
> task-base based images will have to request that from TI. Do you really
> want that?
As so called maintainer of mistical UmbaUmba out-of-tree distribution I also
would like to not have 'omap3-sgx-modules' in extra rrecommends as I do not
need it to run text based systems (unless someone wrote OpenGL accelerated
text console which I know nothing about it).
Regards,
--
JID: hrw@jabber.org
Website: http://marcin.juszkiewicz.com.pl/
LinkedIn: http://www.linkedin.com/in/marcinjuszkiewicz
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2009-12-09 9:18 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2009-12-08 21:11 [PATCH 0/5] Add CM-T35 support Mike Rapoport
2009-12-08 21:11 ` [PATCH 1/5] u-boot git: add cm-t35 support Mike Rapoport
2009-12-08 21:11 ` [PATCH 2/5] linux-omap 2.6.32: " Mike Rapoport
2009-12-08 23:13 ` Koen Kooi
2009-12-09 6:56 ` Mike Rapoport
2009-12-08 21:11 ` [PATCH 3/5] cm-t35: add machine configuration Mike Rapoport
2009-12-08 23:10 ` Koen Kooi
2009-12-09 7:01 ` Mike Rapoport
2009-12-09 9:16 ` Marcin Juszkiewicz
2009-12-08 21:11 ` [PATCH 4/5] angstrom-led-config: Add LED setup for the cm-t35 and bump PR Mike Rapoport
2009-12-08 21:11 ` [PATCH 5/5] xserver-xorg-conf: add cm-t35 support Mike Rapoport
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.