All of lore.kernel.org
 help / color / mirror / Atom feed
From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: matti.vaittinen@fi.rohmeurope.com, mazziesaccount@gmail.com
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>,
	Pavel Machek <pavel@ucw.cz>, Dan Murphy <dmurphy@ti.com>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Lee Jones <lee.jones@linaro.org>,
	Liam Girdwood <lgirdwood@gmail.com>,
	Mark Brown <broonie@kernel.org>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	Linus Walleij <linus.walleij@linaro.org>,
	Bartosz Golaszewski <bgolaszewski@baylibre.com>,
	Alessandro Zummo <a.zummo@towertech.it>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-gpio@vger.kernel.org, linux-rtc@vger.kernel.org
Subject: [RFC PATCH v3 13/15] rtc: bd70528 add BD71828 support
Date: Fri, 1 Nov 2019 13:49:11 +0200	[thread overview]
Message-ID: <d86b3d62170bd680a9f750946cf69a2d509f7b52.1572606437.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1572606437.git.matti.vaittinen@fi.rohmeurope.com>

ROHM BD71828 PMIC RTC block is from many parts similar to one
on BD70528. Support BD71828 RTC using BD70528 RTC driver and
avoid re-inventing the wheel.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>

Changes since v2 - Rebased to v5.4-rc5

---
 drivers/rtc/Kconfig              |   3 +-
 drivers/rtc/rtc-bd70528.c        | 150 ++++++++++++++++++++++++++++---
 include/linux/mfd/rohm-bd70528.h |  13 +--
 include/linux/mfd/rohm-bd71828.h |   4 +-
 include/linux/mfd/rohm-shared.h  |  27 ++++++
 5 files changed, 170 insertions(+), 27 deletions(-)
 create mode 100644 include/linux/mfd/rohm-shared.h

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 1adf9f815652..d03636ec7311 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -509,12 +509,13 @@ config RTC_DRV_M41T80_WDT
 	help
 	  If you say Y here you will get support for the
 	  watchdog timer in the ST M41T60 and M41T80 RTC chips series.
+
 config RTC_DRV_BD70528
 	tristate "ROHM BD70528 PMIC RTC"
 	depends on MFD_ROHM_BD70528 && (BD70528_WATCHDOG || !BD70528_WATCHDOG)
 	help
 	  If you say Y here you will get support for the RTC
-	  on ROHM BD70528 Power Management IC.
+	  block on ROHM BD70528 and BD71828 Power Management IC.
 
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-bd70528.
diff --git a/drivers/rtc/rtc-bd70528.c b/drivers/rtc/rtc-bd70528.c
index 7744333b0f40..fbf407fe0c6d 100644
--- a/drivers/rtc/rtc-bd70528.c
+++ b/drivers/rtc/rtc-bd70528.c
@@ -6,6 +6,7 @@
 
 #include <linux/bcd.h>
 #include <linux/mfd/rohm-bd70528.h>
+#include <linux/mfd/rohm-bd71828.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
@@ -15,7 +16,7 @@
 /*
  * We read regs RTC_SEC => RTC_YEAR
  * this struct is ordered according to chip registers.
- * Keep it u8 only to avoid padding issues.
+ * Keep it u8 only (or packed) to avoid padding issues.
  */
 struct bd70528_rtc_day {
 	u8 sec;
@@ -36,6 +37,13 @@ struct bd70528_rtc_wake {
 	u8 ctrl;
 } __packed;
 
+struct bd71828_rtc_alm {
+	struct bd70528_rtc_data alm0;
+	struct bd70528_rtc_data alm1;
+	u8 alm_mask;
+	u8 alm1_mask;
+} __packed;
+
 struct bd70528_rtc_alm {
 	struct bd70528_rtc_data data;
 	u8 alm_mask;
@@ -45,6 +53,8 @@ struct bd70528_rtc_alm {
 struct bd70528_rtc {
 	struct rohm_regmap_dev *mfd;
 	struct device *dev;
+	u8 reg_time_start;
+	bool has_rtc_timers;
 };
 
 static int bd70528_set_wake(struct rohm_regmap_dev *bd70528,
@@ -152,12 +162,18 @@ static int bd70528_set_rtc_based_timers(struct bd70528_rtc *r, int new_state,
 static int bd70528_re_enable_rtc_based_timers(struct bd70528_rtc *r,
 					      int old_state)
 {
+	if (!r->has_rtc_timers)
+		return 0;
+
 	return bd70528_set_rtc_based_timers(r, old_state, NULL);
 }
 
 static int bd70528_disable_rtc_based_timers(struct bd70528_rtc *r,
 					    int *old_state)
 {
+	if (!r->has_rtc_timers)
+		return 0;
+
 	return bd70528_set_rtc_based_timers(r, 0, old_state);
 }
 
@@ -213,6 +229,36 @@ static inline void rtc2tm(struct bd70528_rtc_data *r, struct rtc_time *t)
 	t->tm_wday = bcd2bin(r->week & BD70528_MASK_RTC_WEEK);
 }
 
+static int bd71828_set_alarm(struct device *dev, struct rtc_wkalrm *a)
+{
+	int ret;
+	struct bd71828_rtc_alm alm;
+	struct bd70528_rtc *r = dev_get_drvdata(dev);
+	struct rohm_regmap_dev *bd71828 = r->mfd;
+
+	ret = regmap_bulk_read(bd71828->regmap, BD71828_REG_RTC_ALM_START,
+			       &alm, sizeof(alm));
+	if (ret) {
+		dev_err(dev, "Failed to read alarm regs\n");
+		return ret;
+	}
+
+	tm2rtc(&a->time, &alm.alm0);
+
+	if (!a->enabled)
+		alm.alm_mask &= ~BD70528_MASK_ALM_EN;
+	else
+		alm.alm_mask |= BD70528_MASK_ALM_EN;
+
+	ret = regmap_bulk_write(bd71828->regmap, BD71828_REG_RTC_ALM_START,
+				&alm, sizeof(alm));
+	if (ret)
+		dev_err(dev, "Failed to set alarm time\n");
+
+	return ret;
+
+}
+
 static int bd70528_set_alarm(struct device *dev, struct rtc_wkalrm *a)
 {
 	struct bd70528_rtc_wake wake;
@@ -261,6 +307,30 @@ static int bd70528_set_alarm(struct device *dev, struct rtc_wkalrm *a)
 	return ret;
 }
 
+static int bd71828_read_alarm(struct device *dev, struct rtc_wkalrm *a)
+{
+	int ret;
+	struct bd71828_rtc_alm alm;
+	struct bd70528_rtc *r = dev_get_drvdata(dev);
+	struct rohm_regmap_dev *bd71828 = r->mfd;
+
+	ret = regmap_bulk_read(bd71828->regmap, BD71828_REG_RTC_ALM_START,
+			       &alm, sizeof(alm));
+	if (ret) {
+		dev_err(dev, "Failed to read alarm regs\n");
+		return ret;
+	}
+
+	rtc2tm(&alm.alm0, &a->time);
+	a->time.tm_mday = -1;
+	a->time.tm_mon = -1;
+	a->time.tm_year = -1;
+	a->enabled = !!(alm.alm_mask & BD70528_MASK_ALM_EN);
+	a->pending = 0;
+
+	return 0;
+}
+
 static int bd70528_read_alarm(struct device *dev, struct rtc_wkalrm *a)
 {
 	struct bd70528_rtc_alm alm;
@@ -297,7 +367,7 @@ static int bd70528_set_time_locked(struct device *dev, struct rtc_time *t)
 		return ret;
 
 	tmpret = regmap_bulk_read(bd70528->regmap,
-				  BD70528_REG_RTC_START, &rtc_data,
+				  r->reg_time_start, &rtc_data,
 				  sizeof(rtc_data));
 	if (tmpret) {
 		dev_err(dev, "Failed to read RTC time registers\n");
@@ -306,7 +376,7 @@ static int bd70528_set_time_locked(struct device *dev, struct rtc_time *t)
 	tm2rtc(t, &rtc_data);
 
 	tmpret = regmap_bulk_write(bd70528->regmap,
-				   BD70528_REG_RTC_START, &rtc_data,
+				   r->reg_time_start, &rtc_data,
 				   sizeof(rtc_data));
 	if (tmpret) {
 		dev_err(dev, "Failed to set RTC time\n");
@@ -341,7 +411,7 @@ static int bd70528_get_time(struct device *dev, struct rtc_time *t)
 
 	/* read the RTC date and time registers all at once */
 	ret = regmap_bulk_read(bd70528->regmap,
-			       BD70528_REG_RTC_START, &rtc_data,
+			       r->reg_time_start, &rtc_data,
 			       sizeof(rtc_data));
 	if (ret) {
 		dev_err(dev, "Failed to read RTC time (err %d)\n", ret);
@@ -378,6 +448,23 @@ static int bd70528_alm_enable(struct device *dev, unsigned int enabled)
 	return ret;
 }
 
+static int bd71828_alm_enable(struct device *dev, unsigned int enabled)
+{
+	int ret;
+	struct bd70528_rtc *r = dev_get_drvdata(dev);
+	unsigned int enableval = BD70528_MASK_ALM_EN;
+
+	if (!enabled)
+		enableval = 0;
+
+	ret = regmap_update_bits(r->mfd->regmap, BD71828_REG_RTC_ALM0_MASK,
+				 BD70528_MASK_ALM_EN, enableval);
+	if (ret)
+		dev_err(dev, "Failed to change alarm state\n");
+
+	return ret;
+}
+
 static const struct rtc_class_ops bd70528_rtc_ops = {
 	.read_time		= bd70528_get_time,
 	.set_time		= bd70528_set_time,
@@ -386,6 +473,14 @@ static const struct rtc_class_ops bd70528_rtc_ops = {
 	.alarm_irq_enable	= bd70528_alm_enable,
 };
 
+static const struct rtc_class_ops bd71828_rtc_ops = {
+	.read_time		= bd70528_get_time,
+	.set_time		= bd70528_set_time,
+	.read_alarm		= bd71828_read_alarm,
+	.set_alarm		= bd71828_set_alarm,
+	.alarm_irq_enable	= bd71828_alm_enable,
+};
+
 static irqreturn_t alm_hndlr(int irq, void *data)
 {
 	struct rtc_device *rtc = data;
@@ -397,11 +492,15 @@ static irqreturn_t alm_hndlr(int irq, void *data)
 static int bd70528_probe(struct platform_device *pdev)
 {
 	struct bd70528_rtc *bd_rtc;
+	const struct rtc_class_ops *rtc_ops;
 	struct rohm_regmap_dev *mfd;
+	const char *irq_name;
 	int ret;
 	struct rtc_device *rtc;
 	int irq;
 	unsigned int hr;
+	bool enable_main_irq = false;
+	u8 hour_reg;
 
 	mfd = dev_get_drvdata(pdev->dev.parent);
 	if (!mfd) {
@@ -415,13 +514,36 @@ static int bd70528_probe(struct platform_device *pdev)
 	bd_rtc->mfd = mfd;
 	bd_rtc->dev = &pdev->dev;
 
-	irq = platform_get_irq_byname(pdev, "bd70528-rtc-alm");
-	if (irq < 0)
+	switch (mfd->chip_type) {
+	case ROHM_CHIP_TYPE_BD70528:
+		irq_name = "bd70528-rtc-alm";
+		bd_rtc->has_rtc_timers = true;
+		bd_rtc->reg_time_start = BD70528_REG_RTC_START;
+		hour_reg = BD70528_REG_RTC_HOUR;
+		enable_main_irq = true;
+		rtc_ops = &bd70528_rtc_ops;
+		break;
+	case ROHM_CHIP_TYPE_BD71828:
+		irq_name = "bd71828-rtc-alm-0";
+		bd_rtc->reg_time_start = BD71828_REG_RTC_START;
+		hour_reg = BD71828_REG_RTC_HOUR;
+		rtc_ops = &bd71828_rtc_ops;
+		break;
+	default:
+		dev_err(&pdev->dev, "Unknown chip\n");
+		return -ENOENT;
+	}
+
+	irq = platform_get_irq_byname(pdev, irq_name);
+
+	if (irq < 0) {
+		dev_err(&pdev->dev, "Failed to get irq\n");
 		return irq;
+	}
 
 	platform_set_drvdata(pdev, bd_rtc);
 
-	ret = regmap_read(mfd->regmap, BD70528_REG_RTC_HOUR, &hr);
+	ret = regmap_read(mfd->regmap, hour_reg, &hr);
 
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to reag RTC clock\n");
@@ -454,7 +576,7 @@ static int bd70528_probe(struct platform_device *pdev)
 
 	rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
 	rtc->range_max = RTC_TIMESTAMP_END_2099;
-	rtc->ops = &bd70528_rtc_ops;
+	rtc->ops = rtc_ops;
 
 	/* Request alarm IRQ prior to registerig the RTC */
 	ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, &alm_hndlr,
@@ -468,12 +590,14 @@ static int bd70528_probe(struct platform_device *pdev)
 	 *  leave them enabled as irq-controller should disable irqs
 	 *  from sub-registers when IRQ is disabled or freed.
 	 */
-	ret = regmap_update_bits(mfd->regmap,
+	if (enable_main_irq) {
+		ret = regmap_update_bits(mfd->regmap,
 				 BD70528_REG_INT_MAIN_MASK,
 				 BD70528_INT_RTC_MASK, 0);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to enable RTC interrupts\n");
-		return ret;
+		if (ret) {
+			dev_err(&pdev->dev, "Failed to enable RTC interrupts\n");
+			return ret;
+		}
 	}
 
 	return rtc_register_device(rtc);
@@ -489,5 +613,5 @@ static struct platform_driver bd70528_rtc = {
 module_platform_driver(bd70528_rtc);
 
 MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
-MODULE_DESCRIPTION("BD70528 RTC driver");
+MODULE_DESCRIPTION("ROHM BD70528 and BD71828 PMIC RTC driver");
 MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/rohm-bd70528.h b/include/linux/mfd/rohm-bd70528.h
index 2ad2320d0a96..a57af878fd0c 100644
--- a/include/linux/mfd/rohm-bd70528.h
+++ b/include/linux/mfd/rohm-bd70528.h
@@ -7,6 +7,7 @@
 #include <linux/bits.h>
 #include <linux/device.h>
 #include <linux/mfd/rohm-generic.h>
+#include <linux/mfd/rohm-shared.h>
 #include <linux/regmap.h>
 
 enum {
@@ -307,17 +308,6 @@ enum {
 
 /* RTC masks to mask out reserved bits */
 
-#define BD70528_MASK_RTC_SEC		0x7f
-#define BD70528_MASK_RTC_MINUTE		0x7f
-#define BD70528_MASK_RTC_HOUR_24H	0x80
-#define BD70528_MASK_RTC_HOUR_PM	0x20
-#define BD70528_MASK_RTC_HOUR		0x1f
-#define BD70528_MASK_RTC_DAY		0x3f
-#define BD70528_MASK_RTC_WEEK		0x07
-#define BD70528_MASK_RTC_MONTH		0x1f
-#define BD70528_MASK_RTC_YEAR		0xff
-#define BD70528_MASK_RTC_COUNT_L	0x7f
-
 #define BD70528_MASK_ELAPSED_TIMER_EN	0x1
 /* Mask second, min and hour fields
  * HW would support ALM irq for over 24h
@@ -326,7 +316,6 @@ enum {
  * wake-up we limit ALM to 24H and only
  * unmask sec, min and hour
  */
-#define BD70528_MASK_ALM_EN		0x7
 #define BD70528_MASK_WAKE_EN		0x1
 
 /* WDT masks */
diff --git a/include/linux/mfd/rohm-bd71828.h b/include/linux/mfd/rohm-bd71828.h
index fc0955f0662c..093662f3e867 100644
--- a/include/linux/mfd/rohm-bd71828.h
+++ b/include/linux/mfd/rohm-bd71828.h
@@ -5,6 +5,7 @@
 #define __LINUX_MFD_BD71828_H__
 
 #include <linux/mfd/rohm-generic.h>
+#include <linux/mfd/rohm-shared.h>
 
 /* Regulator IDs */
 enum {
@@ -160,6 +161,7 @@ enum {
 #define BD71828_REG_RTC_YEAR		0x52
 
 #define BD71828_REG_RTC_ALM0_SEC	0x53
+#define BD71828_REG_RTC_ALM_START	BD71828_REG_RTC_ALM0_SEC
 #define BD71828_REG_RTC_ALM0_MINUTE	0x54
 #define BD71828_REG_RTC_ALM0_HOUR	0x55
 #define BD71828_REG_RTC_ALM0_WEEK	0x56
@@ -178,6 +180,7 @@ enum {
 #define BD71828_REG_RTC_ALM1_MASK	0x62
 
 #define BD71828_REG_RTC_ALM2		0x63
+#define BD71828_REG_RTC_START		BD71828_REG_RTC_SEC
 
 /* Charger/Battey */
 #define BD71828_REG_CHG_STATE		0x65
@@ -204,7 +207,6 @@ enum {
 #define BD71828_REG_INT_MASK_TEMP	0xdd
 #define BD71828_REG_INT_MASK_RTC	0xde
 
-
 #define BD71828_REG_INT_MAIN		0xdf
 #define BD71828_REG_INT_BUCK		0xe0
 #define BD71828_REG_INT_DCIN1		0xe1
diff --git a/include/linux/mfd/rohm-shared.h b/include/linux/mfd/rohm-shared.h
new file mode 100644
index 000000000000..f16fc3b5000e
--- /dev/null
+++ b/include/linux/mfd/rohm-shared.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright (C) 2018 ROHM Semiconductors */
+
+
+#ifndef __LINUX_MFD_ROHM_SHARED_H__
+#define __LINUX_MFD_ROHM_SHARED_H__
+
+/*
+ * RTC definitions shared between
+ *
+ * BD70528
+ * and BD71828
+ */
+
+
+#define BD70528_MASK_RTC_SEC		0x7f
+#define BD70528_MASK_RTC_MINUTE	0x7f
+#define BD70528_MASK_RTC_HOUR_24H	0x80
+#define BD70528_MASK_RTC_HOUR_PM	0x20
+#define BD70528_MASK_RTC_HOUR		0x3f
+#define BD70528_MASK_RTC_DAY		0x3f
+#define BD70528_MASK_RTC_WEEK		0x07
+#define BD70528_MASK_RTC_MONTH		0x1f
+#define BD70528_MASK_RTC_YEAR		0xff
+#define BD70528_MASK_ALM_EN		0x7
+
+#endif /* __LINUX_MFD_ROHM_SHARED_H__ */
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

  parent reply	other threads:[~2019-11-01 11:49 UTC|newest]

Thread overview: 40+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-11-01 11:28 [RFC PATCH v3 00/15] Support ROHM BD71828 PMIC Matti Vaittinen
2019-11-01 11:29 ` [RFC PATCH v3 01/15] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
2019-11-03  1:48   ` kbuild test robot
2019-11-11 10:57   ` Lee Jones
2019-11-11 11:20     ` Vaittinen, Matti
2019-11-01 11:31 ` [RFC PATCH v3 02/15] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
2019-11-05 20:43   ` Rob Herring
2019-11-06 12:55     ` SPAM (R/EU IT) // " Vaittinen, Matti
2019-11-01 11:31 ` [RFC PATCH v3 03/15] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
2019-11-05 20:52   ` Rob Herring
2019-11-07  6:50     ` SPAM (R/EU IT) // " Vaittinen, Matti
2019-11-01 11:32 ` [RFC PATCH v3 04/15] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
2019-11-05 19:14   ` Dan Murphy
2019-11-05 20:59     ` Rob Herring
2019-11-06 13:05     ` Vaittinen, Matti
2019-11-05 20:57   ` Rob Herring
2019-11-01 11:33 ` [RFC PATCH v3 05/15] mfd: input: bd71828: Add power-key support Matti Vaittinen
2019-11-11 10:59   ` Lee Jones
2019-11-11 11:07     ` Vaittinen, Matti
2019-11-01 11:38 ` [RFC PATCH v3 06/15] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
2019-11-01 11:39 ` [RFC PATCH v3 07/15] clk: bd718x7: simplify header dependencies Matti Vaittinen
2019-11-01 11:41 ` [RFC PATCH v3 08/15] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
2019-11-01 11:42 ` [RFC PATCH v3 09/15] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
2019-11-01 11:43 ` [RFC PATCH v3 10/15] regulator: bd71828: Add GPIO based run-level control for regulators Matti Vaittinen
2019-11-03 22:27   ` Linus Walleij
2019-11-04  7:05     ` Vaittinen, Matti
2019-11-05 13:24       ` Linus Walleij
2019-11-05 14:07         ` Vaittinen, Matti
2019-11-01 11:44 ` [RFC PATCH v3 11/15] regulator: bd71828: enhanced run-level support Matti Vaittinen
2019-11-01 11:45 ` [RFC PATCH v3 12/15] regulator: bd71828: Support in-kernel APIs to change run-level Matti Vaittinen
2019-11-01 11:49 ` Matti Vaittinen [this message]
2019-11-01 11:49 ` [RFC PATCH v3 14/15] gpio: Add definition for GPIO direction Matti Vaittinen
2019-11-02 16:45   ` kbuild test robot
2019-11-03 22:30   ` Linus Walleij
2019-11-04  6:57     ` Vaittinen, Matti
2019-11-04 15:48     ` Vaittinen, Matti
2019-11-05 15:05       ` Linus Walleij
2019-11-06  6:51         ` Vaittinen, Matti
2019-11-01 11:51 ` [RFC PATCH v3 15/15] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen
2019-11-01 11:53 ` [RFC PATCH v3 00/15] Support ROHM BD71828 PMIC Vaittinen, Matti

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=d86b3d62170bd680a9f750946cf69a2d509f7b52.1572606437.git.matti.vaittinen@fi.rohmeurope.com \
    --to=matti.vaittinen@fi.rohmeurope.com \
    --cc=a.zummo@towertech.it \
    --cc=alexandre.belloni@bootlin.com \
    --cc=bgolaszewski@baylibre.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dmurphy@ti.com \
    --cc=jacek.anaszewski@gmail.com \
    --cc=lee.jones@linaro.org \
    --cc=lgirdwood@gmail.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=linux-rtc@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mazziesaccount@gmail.com \
    --cc=mturquette@baylibre.com \
    --cc=pavel@ucw.cz \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.