All of lore.kernel.org
 help / color / mirror / Atom feed
From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: matti.vaittinen@fi.rohmeurope.com, mazziesaccount@gmail.com
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>,
	Pavel Machek <pavel@ucw.cz>, Dan Murphy <dmurphy@ti.com>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Lee Jones <lee.jones@linaro.org>,
	Liam Girdwood <lgirdwood@gmail.com>,
	Mark Brown <broonie@kernel.org>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	Linus Walleij <linus.walleij@linaro.org>,
	Bartosz Golaszewski <bgolaszewski@baylibre.com>,
	Alessandro Zummo <a.zummo@towertech.it>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-gpio@vger.kernel.org, linux-rtc@vger.kernel.org
Subject: [RFC PATCH v3 08/15] regulator: bd718x7: Split driver to common and bd718x7 specific parts
Date: Fri, 1 Nov 2019 13:41:01 +0200	[thread overview]
Message-ID: <fe80a2456524580bfa43c0e2fe26f669d5ba5e54.1572606437.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1572606437.git.matti.vaittinen@fi.rohmeurope.com>

Few ROHM PMICs allow setting the voltage states for different system states
like RUN, IDLE, SUSPEND and LPSR. States are then changed via SoC specific
mechanisms. bd718x7 driver implemented device-tree parsing functions for
these state specific voltages. The parsing functions can be re-used by
other ROHM chip drivers like bd71828. Split the generic functions from
bd718x7-regulator.c to rohm-regulator.c and export them for other modules
to use.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---

Changes since v2 - no changes.

 drivers/regulator/Kconfig             |   4 +
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/bd718x7-regulator.c | 183 ++++++++------------------
 drivers/regulator/rohm-regulator.c    |  95 +++++++++++++
 include/linux/mfd/rohm-generic.h      |  44 +++++++
 5 files changed, 199 insertions(+), 128 deletions(-)
 create mode 100644 drivers/regulator/rohm-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 3ee63531f6d5..5182a3d5660c 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -197,6 +197,7 @@ config REGULATOR_BD70528
 config REGULATOR_BD718XX
 	tristate "ROHM BD71837 Power Regulator"
 	depends on MFD_ROHM_BD718XX
+	select REGULATOR_ROHM
 	help
 	  This driver supports voltage regulators on ROHM BD71837 PMIC.
 	  This will enable support for the software controllable buck
@@ -790,6 +791,9 @@ config REGULATOR_RN5T618
 	  Say y here to support the regulators found on Ricoh RN5T567,
 	  RN5T618 or RC5T619 PMIC.
 
+config REGULATOR_ROHM
+	tristate
+
 config REGULATOR_RT5033
 	tristate "Richtek RT5033 Regulators"
 	depends on MFD_RT5033
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 2210ba56f9bd..6bcab72c1fc7 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -99,6 +99,7 @@ obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o
 obj-$(CONFIG_REGULATOR_RC5T583)  += rc5t583-regulator.o
 obj-$(CONFIG_REGULATOR_RK808)   += rk808-regulator.o
 obj-$(CONFIG_REGULATOR_RN5T618) += rn5t618-regulator.o
+obj-$(CONFIG_REGULATOR_ROHM)	+= rohm-regulator.o
 obj-$(CONFIG_REGULATOR_RT5033)	+= rt5033-regulator.o
 obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
 obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c
index bdab46a5c461..2dcb010a626c 100644
--- a/drivers/regulator/bd718x7-regulator.c
+++ b/drivers/regulator/bd718x7-regulator.c
@@ -318,6 +318,7 @@ struct reg_init {
 };
 struct bd718xx_regulator_data {
 	struct regulator_desc desc;
+	const struct rohm_dvs_config dvs;
 	const struct reg_init init;
 	const struct reg_init *additional_inits;
 	int additional_init_amnt;
@@ -349,133 +350,15 @@ static const struct reg_init bd71837_ldo6_inits[] = {
 	},
 };
 
-#define NUM_DVS_BUCKS 4
-
-struct of_dvs_setting {
-	const char *prop;
-	unsigned int reg;
-};
-
-static int set_dvs_levels(const struct of_dvs_setting *dvs,
-			  struct device_node *np,
-			  const struct regulator_desc *desc,
-			  struct regmap *regmap)
-{
-	int ret, i;
-	unsigned int uv;
-
-	ret = of_property_read_u32(np, dvs->prop, &uv);
-	if (ret) {
-		if (ret != -EINVAL)
-			return ret;
-		return 0;
-	}
-
-	for (i = 0; i < desc->n_voltages; i++) {
-		ret = regulator_desc_list_voltage_linear_range(desc, i);
-		if (ret < 0)
-			continue;
-		if (ret == uv) {
-			i <<= ffs(desc->vsel_mask) - 1;
-			ret = regmap_update_bits(regmap, dvs->reg,
-						 DVS_BUCK_RUN_MASK, i);
-			break;
-		}
-	}
-	return ret;
-}
-
-static int buck4_set_hw_dvs_levels(struct device_node *np,
+static int buck_set_hw_dvs_levels(struct device_node *np,
 			    const struct regulator_desc *desc,
 			    struct regulator_config *cfg)
 {
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD71837_REG_BUCK4_VOLT_RUN,
-		},
-	};
+	struct bd718xx_regulator_data *data;
 
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-static int buck3_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD71837_REG_BUCK3_VOLT_RUN,
-		},
-	};
+	data = container_of(desc, struct bd718xx_regulator_data, desc);
 
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-
-static int buck2_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD718XX_REG_BUCK2_VOLT_RUN,
-		},
-		{
-			.prop = "rohm,dvs-idle-voltage",
-			.reg = BD718XX_REG_BUCK2_VOLT_IDLE,
-		},
-	};
-
-
-
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-
-static int buck1_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_RUN,
-		},
-		{
-			.prop = "rohm,dvs-idle-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_IDLE,
-		},
-		{
-			.prop = "rohm,dvs-suspend-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_SUSP,
-		},
-	};
-
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
+	return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
 }
 
 static const struct bd718xx_regulator_data bd71847_regulators[] = {
@@ -496,7 +379,17 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck1_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND,
+			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
+			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
+			.suspend_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -520,7 +413,14 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck2_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
+			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -792,7 +692,17 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck1_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND,
+			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
+			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
+			.suspend_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -816,7 +726,14 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck2_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
+			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -840,7 +757,12 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK3_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck3_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN,
+			.run_reg = BD71837_REG_BUCK3_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK3_CTRL,
@@ -864,7 +786,12 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK4_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck4_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN,
+			.run_reg = BD71837_REG_BUCK4_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK4_CTRL,
diff --git a/drivers/regulator/rohm-regulator.c b/drivers/regulator/rohm-regulator.c
new file mode 100644
index 000000000000..ca368ada53c6
--- /dev/null
+++ b/drivers/regulator/rohm-regulator.c
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 ROHM Semiconductors
+
+#include <linux/errno.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+
+static int set_dvs_level(const struct regulator_desc *desc,
+			 struct device_node *np, struct regmap *regmap,
+			 char *prop, unsigned int reg, unsigned int mask,
+			 unsigned int omask, unsigned int oreg)
+{
+	int ret, i;
+	uint32_t uv;
+
+	ret = of_property_read_u32(np, prop, &uv);
+	if (ret) {
+		if (ret != -EINVAL)
+			return ret;
+		return 0;
+	}
+
+	if (uv == 0) {
+		if (omask)
+			return regmap_update_bits(regmap, oreg, omask, 0);
+	}
+	for (i = 0; i < desc->n_voltages; i++) {
+		ret = regulator_desc_list_voltage_linear_range(desc, i);
+		if (ret < 0)
+			continue;
+		if (ret == uv) {
+			i <<= ffs(desc->vsel_mask) - 1;
+			ret = regmap_update_bits(regmap, reg, mask, i);
+			if (omask && !ret)
+				ret = regmap_update_bits(regmap, oreg, omask,
+							 omask);
+			break;
+		}
+	}
+	return ret;
+}
+
+int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+			  struct device_node *np,
+			  const struct regulator_desc *desc,
+			  struct regmap *regmap)
+{
+	int i, ret = 0;
+	char *prop;
+	unsigned int reg, mask, omask, oreg = desc->enable_reg;
+
+	for (i = 0; i < ROHM_DVS_LEVEL_MAX && !ret; i++) {
+		if (dvs->level_map & (1 << i)) {
+			switch (i + 1) {
+			case ROHM_DVS_LEVEL_RUN:
+				prop = "rohm,dvs-run-voltage";
+				reg = dvs->run_reg;
+				mask = dvs->run_mask;
+				omask = dvs->run_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_IDLE:
+				prop = "rohm,dvs-idle-voltage";
+				reg = dvs->idle_reg;
+				mask = dvs->idle_mask;
+				omask = dvs->idle_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_SUSPEND:
+				prop = "rohm,dvs-suspend-voltage";
+				reg = dvs->suspend_reg;
+				mask = dvs->suspend_mask;
+				omask = dvs->suspend_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_LPSR:
+				prop = "rohm,dvs-lpsr-voltage";
+				reg = dvs->lpsr_reg;
+				mask = dvs->lpsr_mask;
+				omask = dvs->lpsr_on_mask;
+				break;
+			default:
+				return -EINVAL;
+			}
+			ret = set_dvs_level(desc, np, regmap, prop, reg, mask,
+					    omask, oreg);
+		}
+	}
+	return ret;
+}
+EXPORT_SYMBOL(rohm_regulator_set_dvs_levels);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("Generic helpers for ROHM PMIC regulator drivers");
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index b280f3100d6c..86397b42e9bf 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -4,6 +4,9 @@
 #ifndef __LINUX_MFD_ROHM_H__
 #define __LINUX_MFD_ROHM_H__
 
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+
 enum {
 	ROHM_CHIP_TYPE_BD71837 = 0,
 	ROHM_CHIP_TYPE_BD71847,
@@ -18,4 +21,45 @@ struct rohm_regmap_dev {
 	struct regmap *regmap;
 };
 
+enum {
+	ROHM_DVS_LEVEL_UNKNOWN,
+	ROHM_DVS_LEVEL_RUN,
+	ROHM_DVS_LEVEL_IDLE,
+	ROHM_DVS_LEVEL_SUSPEND,
+	ROHM_DVS_LEVEL_LPSR,
+#define ROHM_DVS_LEVEL_MAX ROHM_DVS_LEVEL_LPSR
+};
+
+struct rohm_dvs_config {
+	uint64_t level_map;
+	unsigned int run_reg;
+	unsigned int run_mask;
+	unsigned int run_on_mask;
+	unsigned int idle_reg;
+	unsigned int idle_mask;
+	unsigned int idle_on_mask;
+	unsigned int suspend_reg;
+	unsigned int suspend_mask;
+	unsigned int suspend_on_mask;
+	unsigned int lpsr_reg;
+	unsigned int lpsr_mask;
+	unsigned int lpsr_on_mask;
+};
+
+#if IS_ENABLED(CONFIG_REGULATOR_ROHM)
+int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+				  struct device_node *np,
+				  const struct regulator_desc *desc,
+				  struct regmap *regmap);
+
+#else
+static inline int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+						struct device_node *np,
+						const struct regulator_desc *desc,
+						struct regmap *regmap)
+{
+	return 0;
+}
+#endif //IS_ENABLED(CONFIG_REGULATOR_ROHM)
+
 #endif
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

  parent reply	other threads:[~2019-11-01 11:41 UTC|newest]

Thread overview: 40+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-11-01 11:28 [RFC PATCH v3 00/15] Support ROHM BD71828 PMIC Matti Vaittinen
2019-11-01 11:29 ` [RFC PATCH v3 01/15] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
2019-11-03  1:48   ` kbuild test robot
2019-11-11 10:57   ` Lee Jones
2019-11-11 11:20     ` Vaittinen, Matti
2019-11-01 11:31 ` [RFC PATCH v3 02/15] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
2019-11-05 20:43   ` Rob Herring
2019-11-06 12:55     ` SPAM (R/EU IT) // " Vaittinen, Matti
2019-11-01 11:31 ` [RFC PATCH v3 03/15] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
2019-11-05 20:52   ` Rob Herring
2019-11-07  6:50     ` SPAM (R/EU IT) // " Vaittinen, Matti
2019-11-01 11:32 ` [RFC PATCH v3 04/15] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
2019-11-05 19:14   ` Dan Murphy
2019-11-05 20:59     ` Rob Herring
2019-11-06 13:05     ` Vaittinen, Matti
2019-11-05 20:57   ` Rob Herring
2019-11-01 11:33 ` [RFC PATCH v3 05/15] mfd: input: bd71828: Add power-key support Matti Vaittinen
2019-11-11 10:59   ` Lee Jones
2019-11-11 11:07     ` Vaittinen, Matti
2019-11-01 11:38 ` [RFC PATCH v3 06/15] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
2019-11-01 11:39 ` [RFC PATCH v3 07/15] clk: bd718x7: simplify header dependencies Matti Vaittinen
2019-11-01 11:41 ` Matti Vaittinen [this message]
2019-11-01 11:42 ` [RFC PATCH v3 09/15] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
2019-11-01 11:43 ` [RFC PATCH v3 10/15] regulator: bd71828: Add GPIO based run-level control for regulators Matti Vaittinen
2019-11-03 22:27   ` Linus Walleij
2019-11-04  7:05     ` Vaittinen, Matti
2019-11-05 13:24       ` Linus Walleij
2019-11-05 14:07         ` Vaittinen, Matti
2019-11-01 11:44 ` [RFC PATCH v3 11/15] regulator: bd71828: enhanced run-level support Matti Vaittinen
2019-11-01 11:45 ` [RFC PATCH v3 12/15] regulator: bd71828: Support in-kernel APIs to change run-level Matti Vaittinen
2019-11-01 11:49 ` [RFC PATCH v3 13/15] rtc: bd70528 add BD71828 support Matti Vaittinen
2019-11-01 11:49 ` [RFC PATCH v3 14/15] gpio: Add definition for GPIO direction Matti Vaittinen
2019-11-02 16:45   ` kbuild test robot
2019-11-03 22:30   ` Linus Walleij
2019-11-04  6:57     ` Vaittinen, Matti
2019-11-04 15:48     ` Vaittinen, Matti
2019-11-05 15:05       ` Linus Walleij
2019-11-06  6:51         ` Vaittinen, Matti
2019-11-01 11:51 ` [RFC PATCH v3 15/15] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen
2019-11-01 11:53 ` [RFC PATCH v3 00/15] Support ROHM BD71828 PMIC Vaittinen, Matti

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=fe80a2456524580bfa43c0e2fe26f669d5ba5e54.1572606437.git.matti.vaittinen@fi.rohmeurope.com \
    --to=matti.vaittinen@fi.rohmeurope.com \
    --cc=a.zummo@towertech.it \
    --cc=alexandre.belloni@bootlin.com \
    --cc=bgolaszewski@baylibre.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dmurphy@ti.com \
    --cc=jacek.anaszewski@gmail.com \
    --cc=lee.jones@linaro.org \
    --cc=lgirdwood@gmail.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=linux-rtc@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mazziesaccount@gmail.com \
    --cc=mturquette@baylibre.com \
    --cc=pavel@ucw.cz \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.