[U-Boot] [PATCHv6 1/3] ARM64: dts: hi3798cv200-poplar: add device tree bindings

[U-Boot] [PATCHv6 1/3] ARM64: dts: hi3798cv200-poplar: add device tree bindings

[Jorge Ramirez-Ortiz]

Pulled from Linux 4.12-rc3

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
 arch/arm/dts/hi3798cv200-poplar.dts     | 162 +++++++++++++
 arch/arm/dts/hi3798cv200.dtsi           | 411 ++++++++++++++++++++++++++++++++
 include/dt-bindings/clock/histb-clock.h |  66 +++++
 include/dt-bindings/reset/ti-syscon.h   |  38 +++
 4 files changed, 677 insertions(+)
 create mode 100644 arch/arm/dts/hi3798cv200-poplar.dts
 create mode 100644 arch/arm/dts/hi3798cv200.dtsi
 create mode 100644 include/dt-bindings/clock/histb-clock.h
 create mode 100644 include/dt-bindings/reset/ti-syscon.h

diff --git a/arch/arm/dts/hi3798cv200-poplar.dts b/arch/arm/dts/hi3798cv200-poplar.dts
new file mode 100644
index 0000000..b914287
--- /dev/null
+++ b/arch/arm/dts/hi3798cv200-poplar.dts
@@ -0,0 +1,162 @@
+/*
+ * DTS File for HiSilicon Poplar Development Board
+ *
+ * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
+ *
+ * Released under the GPLv2 only.
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "hi3798cv200.dtsi"
+
+/ {
+	model = "HiSilicon Poplar Development Board";
+	compatible = "hisilicon,hi3798cv200-poplar", "hisilicon,hi3798cv200";
+
+	aliases {
+		serial0 = &uart0;
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory at 0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user-led0 {
+			label = "USER-LED0";
+			gpios = <&gpio6 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		user-led1 {
+			label = "USER-LED1";
+			gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		user-led2 {
+			label = "USER-LED2";
+			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+		};
+
+		user-led3 {
+			label = "USER-LED3";
+			gpios = <&gpio10 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "cpu0";
+			default-state = "off";
+		};
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	phy-handle = <&eth_phy1>;
+	phy-mode = "rgmii";
+	hisilicon,phy-reset-delays-us = <10000 10000 30000>;
+
+	eth_phy1: phy at 3 {
+		reg = <3>;
+	};
+};
+
+&gpio1 {
+	status = "okay";
+	gpio-line-names = "LS-GPIO-E",	"",
+			  "",		"",
+			  "",		"LS-GPIO-F",
+			  "",		"LS-GPIO-J";
+};
+
+&gpio2 {
+	status = "okay";
+	gpio-line-names = "LS-GPIO-H",	"LS-GPIO-I",
+			  "LS-GPIO-L",	"LS-GPIO-G",
+			  "LS-GPIO-K",	"",
+			  "",		"";
+};
+
+&gpio3 {
+	status = "okay";
+	gpio-line-names = "",		"",
+			  "",		"",
+			  "LS-GPIO-C",	"",
+			  "",		"LS-GPIO-B";
+};
+
+&gpio4 {
+	status = "okay";
+	gpio-line-names = "",		"",
+			  "",		"",
+			  "",		"LS-GPIO-D",
+			  "",		"";
+};
+
+&gpio5 {
+	status = "okay";
+	gpio-line-names = "",		"USER-LED-1",
+			  "USER-LED-2",	"",
+			  "",		"LS-GPIO-A",
+			  "",		"";
+};
+
+&gpio6 {
+	status = "okay";
+	gpio-line-names = "",		"",
+			  "",		"USER-LED-0",
+			  "",		"",
+			  "",		"";
+};
+
+&gpio10 {
+	status = "okay";
+	gpio-line-names = "",		"",
+			  "",		"",
+			  "",		"",
+			  "USER-LED-3",	"";
+};
+
+&i2c0 {
+	status = "okay";
+	label = "LS-I2C0";
+};
+
+&i2c2 {
+	status = "okay";
+	label = "LS-I2C1";
+};
+
+&ir {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+	label = "LS-SPI0";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+	label = "LS-UART0";
+};
+/* No optional LS-UART1 on Low Speed Expansion Connector. */
diff --git a/arch/arm/dts/hi3798cv200.dtsi b/arch/arm/dts/hi3798cv200.dtsi
new file mode 100644
index 0000000..75865f8
--- /dev/null
+++ b/arch/arm/dts/hi3798cv200.dtsi
@@ -0,0 +1,411 @@
+/*
+ * DTS File for HiSilicon Hi3798cv200 SoC.
+ *
+ * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
+ *
+ * Released under the GPLv2 only.
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <dt-bindings/clock/histb-clock.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/ti-syscon.h>
+
+/ {
+	compatible = "hisilicon,hi3798cv200";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+		};
+
+		cpu at 1 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+		};
+
+		cpu at 2 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0x0 0x2>;
+			enable-method = "psci";
+		};
+
+		cpu at 3 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0x0 0x3>;
+			enable-method = "psci";
+		};
+	};
+
+	gic: interrupt-controller at f1001000 {
+		compatible = "arm,gic-400";
+		reg = <0x0 0xf1001000 0x0 0x1000>,  /* GICD */
+		      <0x0 0xf1002000 0x0 0x100>;   /* GICC */
+		#address-cells = <0>;
+		#interrupt-cells = <3>;
+		interrupt-controller;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
+			      IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) |
+			      IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) |
+			      IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
+			      IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc: soc at f0000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xf0000000 0x10000000>;
+
+		crg: clock-reset-controller at 8a22000 {
+			compatible = "hisilicon,hi3798cv200-crg", "syscon", "simple-mfd";
+			reg = <0x8a22000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <2>;
+
+			gmacphyrst: reset-controller {
+				compatible = "ti,syscon-reset";
+				#reset-cells = <1>;
+				ti,reset-bits =
+					<0xcc 12 0xcc 12 0 0 (ASSERT_CLEAR |
+					 DEASSERT_SET|STATUS_NONE)>,
+					<0xcc 13 0xcc 13 0 0 (ASSERT_CLEAR |
+					 DEASSERT_SET|STATUS_NONE)>;
+			};
+		};
+
+		sysctrl: system-controller at 8000000 {
+			compatible = "hisilicon,hi3798cv200-sysctrl", "syscon";
+			reg = <0x8000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <2>;
+		};
+
+		uart0: serial at 8b00000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x8b00000 0x1000>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl HISTB_UART0_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		uart2: serial at 8b02000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x8b02000 0x1000>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&crg HISTB_UART2_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		i2c0: i2c at 8b10000 {
+			compatible = "hisilicon,hix5hd2-i2c";
+			reg = <0x8b10000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <400000>;
+			clocks = <&crg HISTB_I2C0_CLK>;
+			status = "disabled";
+		};
+
+		i2c1: i2c at 8b11000 {
+			compatible = "hisilicon,hix5hd2-i2c";
+			reg = <0x8b11000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <400000>;
+			clocks = <&crg HISTB_I2C1_CLK>;
+			status = "disabled";
+		};
+
+		i2c2: i2c at 8b12000 {
+			compatible = "hisilicon,hix5hd2-i2c";
+			reg = <0x8b12000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <400000>;
+			clocks = <&crg HISTB_I2C2_CLK>;
+			status = "disabled";
+		};
+
+		i2c3: i2c at 8b13000 {
+			compatible = "hisilicon,hix5hd2-i2c";
+			reg = <0x8b13000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <400000>;
+			clocks = <&crg HISTB_I2C3_CLK>;
+			status = "disabled";
+		};
+
+		i2c4: i2c at 8b14000 {
+			compatible = "hisilicon,hix5hd2-i2c";
+			reg = <0x8b14000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <400000>;
+			clocks = <&crg HISTB_I2C4_CLK>;
+			status = "disabled";
+		};
+
+		spi0: spi at 8b1a000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x8b1a000 0x1000>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			num-cs = <1>;
+			cs-gpios = <&gpio7 1 0>;
+			clocks = <&crg HISTB_SPI0_CLK>;
+			clock-names = "apb_pclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		emmc: mmc at 9830000 {
+			compatible = "snps,dw-mshc";
+			reg = <0x9830000 0x10000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&crg HISTB_MMC_CIU_CLK>,
+				 <&crg HISTB_MMC_BIU_CLK>;
+			clock-names = "ciu", "biu";
+		};
+
+		gpio0: gpio at 8b20000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b20000 0x1000>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio1: gpio at 8b21000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b21000 0x1000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio2: gpio at 8b22000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b22000 0x1000>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio3: gpio at 8b23000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b23000 0x1000>;
+			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio4: gpio at 8b24000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b24000 0x1000>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio5: gpio at 8004000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8004000 0x1000>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio6: gpio at 8b26000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b26000 0x1000>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio7: gpio at 8b27000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b27000 0x1000>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio8: gpio at 8b28000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b28000 0x1000>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio9: gpio at 8b29000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b29000 0x1000>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio10: gpio at 8b2a000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b2a000 0x1000>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio11: gpio at 8b2b000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b2b000 0x1000>;
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio12: gpio at 8b2c000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x8b2c000 0x1000>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&crg HISTB_APB_CLK>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gmac0: ethernet at 9840000 {
+			compatible = "hisilicon,hi3798cv200-gmac", "hisilicon,hisi-gmac-v2";
+			reg = <0x9840000 0x1000>,
+			      <0x984300c 0x4>;
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&crg HISTB_ETH0_MAC_CLK>,
+				 <&crg HISTB_ETH0_MACIF_CLK>;
+			clock-names = "mac_core", "mac_ifc";
+			resets = <&crg 0xcc 8>,
+				 <&crg 0xcc 10>,
+				 <&gmacphyrst 0>;
+			reset-names = "mac_core", "mac_ifc", "phy";
+			status = "disabled";
+		};
+
+		gmac1: ethernet at 9841000 {
+			compatible = "hisilicon,hi3798cv200-gmac", "hisilicon,hisi-gmac-v2";
+			reg = <0x9841000 0x1000>,
+			      <0x9843010 0x4>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&crg HISTB_ETH1_MAC_CLK>,
+				 <&crg HISTB_ETH1_MACIF_CLK>;
+			clock-names = "mac_core", "mac_ifc";
+			resets = <&crg 0xcc 9>,
+				 <&crg 0xcc 11>,
+				 <&gmacphyrst 1>;
+			reset-names = "mac_core", "mac_ifc", "phy";
+			status = "disabled";
+		};
+
+		ir: ir at 8001000 {
+			compatible = "hisilicon,hix5hd2-ir";
+			reg = <0x8001000 0x1000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl HISTB_IR_CLK>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/include/dt-bindings/clock/histb-clock.h b/include/dt-bindings/clock/histb-clock.h
new file mode 100644
index 0000000..181c0f0
--- /dev/null
+++ b/include/dt-bindings/clock/histb-clock.h
@@ -0,0 +1,66 @@
+/*
+ * Copyright (c) 2016 HiSilicon Technologies Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __DTS_HISTB_CLOCK_H
+#define __DTS_HISTB_CLOCK_H
+
+/* clocks provided by core CRG */
+#define HISTB_OSC_CLK			0
+#define HISTB_APB_CLK			1
+#define HISTB_AHB_CLK			2
+#define HISTB_UART1_CLK		3
+#define HISTB_UART2_CLK		4
+#define HISTB_UART3_CLK		5
+#define HISTB_I2C0_CLK		6
+#define HISTB_I2C1_CLK		7
+#define HISTB_I2C2_CLK		8
+#define HISTB_I2C3_CLK		9
+#define HISTB_I2C4_CLK		10
+#define HISTB_I2C5_CLK		11
+#define HISTB_SPI0_CLK		12
+#define HISTB_SPI1_CLK		13
+#define HISTB_SPI2_CLK		14
+#define HISTB_SCI_CLK			15
+#define HISTB_FMC_CLK			16
+#define HISTB_MMC_BIU_CLK		17
+#define HISTB_MMC_CIU_CLK		18
+#define HISTB_MMC_DRV_CLK		19
+#define HISTB_MMC_SAMPLE_CLK		20
+#define HISTB_SDIO0_BIU_CLK		21
+#define HISTB_SDIO0_CIU_CLK		22
+#define HISTB_SDIO0_DRV_CLK		23
+#define HISTB_SDIO0_SAMPLE_CLK	24
+#define HISTB_PCIE_AUX_CLK		25
+#define HISTB_PCIE_PIPE_CLK		26
+#define HISTB_PCIE_SYS_CLK		27
+#define HISTB_PCIE_BUS_CLK		28
+#define HISTB_ETH0_MAC_CLK		29
+#define HISTB_ETH0_MACIF_CLK		30
+#define HISTB_ETH1_MAC_CLK		31
+#define HISTB_ETH1_MACIF_CLK		32
+#define HISTB_COMBPHY1_CLK		33
+
+
+/* clocks provided by mcu CRG */
+#define HISTB_MCE_CLK	1
+#define HISTB_IR_CLK	2
+#define HISTB_TIMER01_CLK	3
+#define HISTB_LEDC_CLK	4
+#define HISTB_UART0_CLK	5
+#define HISTB_LSADC_CLK	6
+
+#endif	/* __DTS_HISTB_CLOCK_H */
diff --git a/include/dt-bindings/reset/ti-syscon.h b/include/dt-bindings/reset/ti-syscon.h
new file mode 100644
index 0000000..884fd91
--- /dev/null
+++ b/include/dt-bindings/reset/ti-syscon.h
@@ -0,0 +1,38 @@
+/*
+ * TI Syscon Reset definitions
+ *
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __DT_BINDINGS_RESET_TI_SYSCON_H__
+#define __DT_BINDINGS_RESET_TI_SYSCON_H__
+
+/*
+ * The reset does not support the feature and corresponding
+ * values are not valid
+ */
+#define ASSERT_NONE	(1 << 0)
+#define DEASSERT_NONE	(1 << 1)
+#define STATUS_NONE	(1 << 2)
+
+/* When set this function is activated by setting(vs clearing) this bit */
+#define ASSERT_SET	(1 << 3)
+#define DEASSERT_SET	(1 << 4)
+#define STATUS_SET	(1 << 5)
+
+/* The following are the inverse of the above and are added for consistency */
+#define ASSERT_CLEAR	(0 << 3)
+#define DEASSERT_CLEAR	(0 << 4)
+#define STATUS_CLEAR	(0 << 5)
+
+#endif
-- 
2.7.4

[U-Boot] [PATCHv6 2/3] driver: mmc: update debug info

[Jorge Ramirez-Ortiz]

This driver is used in another board; remove board information from
the driver debug log.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
 drivers/mmc/hi6220_dw_mmc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mmc/hi6220_dw_mmc.c b/drivers/mmc/hi6220_dw_mmc.c
index fdaf1e4..d795198 100644
--- a/drivers/mmc/hi6220_dw_mmc.c
+++ b/drivers/mmc/hi6220_dw_mmc.c
@@ -20,7 +20,7 @@
 
 static int hi6220_dwmci_core_init(struct dwmci_host *host, int index)
 {
-	host->name = "HiKey DWMMC";
+	host->name = "Hisilicon DWMMC";
 
 	host->dev_index = index;
 
-- 
2.7.4

[U-Boot] [PATCHv6 3/3] ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards

[Jorge Ramirez-Ortiz]

This port adds support for:
        1) Serial
        2) eMMC
        3) USB

It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]

eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.

USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.

PSCI has been tested via the reset call (PSCI executes from DDR)

The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
 arch/arm/Kconfig                                   |  14 +
 arch/arm/dts/hi3798cv200-u-boot.dtsi               |  29 +++
 arch/arm/include/asm/arch-hi3798cv200/dwmmc.h      |  13 +
 .../arm/include/asm/arch-hi3798cv200/hi3798cv200.h |  50 ++++
 board/hisilicon/poplar/Kconfig                     |  15 ++
 board/hisilicon/poplar/MAINTAINERS                 |   6 +
 board/hisilicon/poplar/Makefile                    |   7 +
 board/hisilicon/poplar/README                      | 288 +++++++++++++++++++++
 board/hisilicon/poplar/poplar.c                    | 174 +++++++++++++
 configs/poplar_defconfig                           |  26 ++
 include/configs/poplar.h                           |  86 ++++++
 11 files changed, 708 insertions(+)
 create mode 100644 arch/arm/dts/hi3798cv200-u-boot.dtsi
 create mode 100644 arch/arm/include/asm/arch-hi3798cv200/dwmmc.h
 create mode 100644 arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h
 create mode 100644 board/hisilicon/poplar/Kconfig
 create mode 100644 board/hisilicon/poplar/MAINTAINERS
 create mode 100644 board/hisilicon/poplar/Makefile
 create mode 100644 board/hisilicon/poplar/README
 create mode 100644 board/hisilicon/poplar/poplar.c
 create mode 100644 configs/poplar_defconfig
 create mode 100644 include/configs/poplar.h

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 46183ae..4b4f51c 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -837,6 +837,19 @@ config TARGET_HIKEY
 	  Support for HiKey 96boards platform. It features a HI6220
 	  SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.
 
+config TARGET_POPLAR
+	bool "Support Poplar 96boards Enterprise Edition Platform"
+	select ARM64
+	select DM
+	select OF_CONTROL
+	select DM_SERIAL
+	select DM_USB
+	  help
+	  Support for Poplar 96boards EE platform. It features a HI3798cv200
+	  SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU
+	  making it capable of running any commercial set-top solution based on
+	  Linux or Android.
+
 config TARGET_LS1012AQDS
 	bool "Support ls1012aqds"
 	select ARCH_LS1012A
@@ -1165,6 +1178,7 @@ source "board/grinn/chiliboard/Kconfig"
 source "board/gumstix/pepper/Kconfig"
 source "board/h2200/Kconfig"
 source "board/hisilicon/hikey/Kconfig"
+source "board/hisilicon/poplar/Kconfig"
 source "board/imx31_phycore/Kconfig"
 source "board/isee/igep003x/Kconfig"
 source "board/olimex/mx23_olinuxino/Kconfig"
diff --git a/arch/arm/dts/hi3798cv200-u-boot.dtsi b/arch/arm/dts/hi3798cv200-u-boot.dtsi
new file mode 100644
index 0000000..2b3713b
--- /dev/null
+++ b/arch/arm/dts/hi3798cv200-u-boot.dtsi
@@ -0,0 +1,29 @@
+/*
+ * U-Boot addition to:
+ *  1) use platform data for the console
+ *  2) provide support for the generic-ehci USB driver currently not available
+ *     in the linux kernel (8/May/2017).
+ *
+ * (C) Copyright 2017 Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+&soc {
+	usb2: ehci at 9890000 {
+		compatible = "generic-ehci";
+		reg = <0x9890000 0x100>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	status = "disabled";
+};
+
+/{
+	chosen {
+		stdout-path = "";
+	};
+};
+
diff --git a/arch/arm/include/asm/arch-hi3798cv200/dwmmc.h b/arch/arm/include/asm/arch-hi3798cv200/dwmmc.h
new file mode 100644
index 0000000..1060d94
--- /dev/null
+++ b/arch/arm/include/asm/arch-hi3798cv200/dwmmc.h
@@ -0,0 +1,13 @@
+/*
+ * (C) Copyright 2017 Linaro
+ * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _HI3798cv200_DWMMC_H_
+#define _HI3798cv200_DWMMC_H_
+
+int hi6220_dwmci_add_port(int index, u32 regbase, int bus_width);
+
+#endif /* _HI3798cv200_DWMMC_H_ */
diff --git a/arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h b/arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h
new file mode 100644
index 0000000..d30e0b4
--- /dev/null
+++ b/arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h
@@ -0,0 +1,50 @@
+/*
+ * (C) Copyright 2017 Linaro
+ * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __HI3798cv200_H__
+#define __HI3798cv200_H__
+
+#define REG_BASE_PERI_CTRL		0xF8A20000
+#define REG_BASE_CRG			0xF8A22000
+
+/* DEVICES */
+#define REG_BASE_MCI			0xF9830000
+#define REG_BASE_UART0			0xF8B00000
+
+/* PERI control registers (4KB) */
+	/* USB2 PHY01 configuration register */
+#define PERI_CTRL_USB0			(REG_BASE_PERI_CTRL + 0x120)
+
+/* PERI CRG registers (4KB) */
+	/* USB2 CTRL0 clock and soft reset */
+#define PERI_CRG46			(REG_BASE_CRG + 0xb8)
+#define USB2_BUS_CKEN			(1<<0)
+#define USB2_OHCI48M_CKEN		(1<<1)
+#define USB2_OHCI12M_CKEN		(1<<2)
+#define USB2_OTG_UTMI_CKEN		(1<<3)
+#define USB2_HST_PHY_CKEN		(1<<4)
+#define USB2_UTMI0_CKEN			(1<<5)
+#define USB2_BUS_SRST_REQ		(1<<12)
+#define USB2_UTMI0_SRST_REQ		(1<<13)
+#define USB2_HST_PHY_SYST_REQ		(1<<16)
+#define USB2_OTG_PHY_SYST_REQ		(1<<17)
+#define USB2_CLK48_SEL			(1<<20)
+
+	/* USB2 PHY clock and soft reset */
+#define PERI_CRG47			(REG_BASE_CRG + 0xbc)
+#define USB2_PHY01_REF_CKEN		(1 << 0)
+#define USB2_PHY2_REF_CKEN		(1 << 2)
+#define USB2_PHY01_SRST_REQ		(1 << 4)
+#define USB2_PHY2_SRST_REQ		(1 << 6)
+#define USB2_PHY01_SRST_TREQ0		(1 << 8)
+#define USB2_PHY01_SRST_TREQ1		(1 << 9)
+#define USB2_PHY2_SRST_TREQ		(1 << 10)
+#define USB2_PHY01_REFCLK_SEL		(1 << 12)
+#define USB2_PHY2_REFCLK_SEL		(1 << 14)
+
+
+#endif
diff --git a/board/hisilicon/poplar/Kconfig b/board/hisilicon/poplar/Kconfig
new file mode 100644
index 0000000..3397295
--- /dev/null
+++ b/board/hisilicon/poplar/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_POPLAR
+
+config SYS_BOARD
+	default "poplar"
+
+config SYS_VENDOR
+	default "hisilicon"
+
+config SYS_SOC
+	default "hi3798cv200"
+
+config SYS_CONFIG_NAME
+	default "poplar"
+
+endif
diff --git a/board/hisilicon/poplar/MAINTAINERS b/board/hisilicon/poplar/MAINTAINERS
new file mode 100644
index 0000000..0cc01c8
--- /dev/null
+++ b/board/hisilicon/poplar/MAINTAINERS
@@ -0,0 +1,6 @@
+Poplar BOARD
+M:     Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
+S:     Maintained
+F:     board/hisilicon/poplar
+F:     include/configs/poplar.h
+F:     configs/poplar_defconfig
diff --git a/board/hisilicon/poplar/Makefile b/board/hisilicon/poplar/Makefile
new file mode 100644
index 0000000..101545d
--- /dev/null
+++ b/board/hisilicon/poplar/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2017 Linaro
+# Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+obj-y	:= poplar.o
diff --git a/board/hisilicon/poplar/README b/board/hisilicon/poplar/README
new file mode 100644
index 0000000..99ed6ce
--- /dev/null
+++ b/board/hisilicon/poplar/README
@@ -0,0 +1,288 @@
+================================================================================
+			Board Information
+================================================================================
+
+Developed by HiSilicon, the board features the Hi3798C V200 with an
+integrated quad-core 64-bit ARM Cortex A53 processor and high
+performance Mali T720 GPU, making it capable of running any commercial
+set-top solution based on Linux or Android. Its high performance
+specification also supports a premium user experience with up to H.265
+HEVC decoding of 4K video at 60 frames per second.
+
+SOC  Hisilicon Hi3798CV200
+CPU  Quad-core ARM Cortex-A53 64 bit
+DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB
+USB  Two USB 2.0 ports One USB 3.0 ports
+CONSOLE  USB-micro port for console support
+ETHERNET  1 GBe Ethernet
+PCIE  One PCIe 2.0 interfaces
+JTAG  8-Pin JTAG
+EXPANSION INTERFACE  Linaro 96Boards Low Speed Expansion slot
+DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor
+WIFI  802.11AC 2*2 with Bluetooth
+CONNECTORS  One connector for Smart Card One connector for TSI
+
+
+================================================================================
+			BUILD INSTRUCTIONS
+================================================================================
+
+Note of warning:
+================
+
+U-boot has a *strong* dependency with the l-loader and the arm trusted firmware
+repositories.
+
+The boot sequence is:
+	l-loader --> arm_trusted_firmware --> u-boot
+
+U-Boot needs to be aware of the BL31 runtime location and size to avoid writing
+over it. Currently, BL31 is being placed below the kernel text offset (check
+poplar.c) but this could change in the future.
+
+The current version of u-boot has been tested with:
+ - https://github.com/Linaro/poplar-l-loader.git
+
+	commit f0988698dcc5c08bd0a8f50aa0457e138a5f438c
+	Author: Alex Elder <elder@linaro.org>
+	Date:   Fri Jun 16 08:57:59 2017 -0500
+
+    l-loader: use external memory region definitions
+
+    The ARM Trusted Firmware code now has a header file that collects
+    all the definitions for the memory regions used for its boot stages.
+    Include that file where needed, and use the definitions found therein
+
+    Signed-off-by: Alex Elder <elder@linaro.org>
+
+
+ - https://github.com/Linaro/poplar-arm-trusted-firmware.git
+
+	commit 6ac42dd3be13c99aa8ce29a15073e2f19d935f68
+	Author: Alex Elder <elder@linaro.org>
+	Date:   Fri Jun 16 09:24:50 2017 -0500
+
+    poplar: define memory regions in a separate file
+
+    Separate the definitions for memory regions used for the BL stage
+    images and FIP into a new file.  The "l-loader" image uses knowledge
+    of the sizes and locations of these memory regions, and it can now
+    include this (external) header to get these definitions, rather than
+    having to make coordinated changes to both code bases.
+
+    The new file has a complete set of definitions (more than may be
+    required by one or the other user).  It also includes a summary of
+    how the boot process works, and how it uses these regions.
+
+    It should now be relatively easy to adjust the sizes and locations
+    of these memory regions, or to add to them (e.g. for TEE).
+
+    Signed-off-by: Alex Elder <elder@linaro.org>
+
+
+Compile from source:
+====================
+
+Get all the sources
+
+  > mkdir -p ~/poplar/src ~/poplar/bin
+  > cd ~/poplar/src
+  > git clone https://github.com/Linaro/poplar-l-loader.git l-loader
+  > git clone https://github.com/Linaro/poplar-arm-trusted-firmware.git atf
+  > git clone https://github.com/Linaro/poplar-u-boot.git u-boot
+
+Make sure you are using the correct branch on each one of these repositories.
+The definition of "correct" might change over time (at this moment in time this
+would be the "latest" branch).
+
+Compile U-Boot:
+===============
+
+  Prerequisite:
+  # sudo apt-get install device-tree-compiler
+
+  > cd ~/poplar/src/u-boot
+  > make CROSS_COMPILE=aarch64-linux-gnu- poplar_defconfig
+  > make CROSS_COMPILE=aarch64-linux-gnu-
+  > cp u-boot.bin ~/poplar/bin
+
+Compile ARM Trusted Firmware (ATF):
+===================================
+
+  > cd ~/poplar/src/atf
+  > make CROSS_COMPILE=aarch64-linux-gnu- all fip \
+		SPD=none BL33=~/poplar/bin/u-boot.bin DEBUG=1 PLAT=poplar
+
+Copy resulting binaries
+  > cp build/hi3798cv200/debug/bl1.bin ~/poplar/src/l-loader/atf/
+  > cp build/hi3798cv200/debug/fip.bin ~/poplar/src/l-loader/atf/
+
+Compile l-loader:
+=================
+
+  > cd ~/poplar/src/l-loader
+  > make clean
+  > make CROSS_COMPILE=arm-linux-gnueabi-
+
+   Due to BootROM requiremets, rename l-loader.bin to fastboot.bin:
+  > cp l-loader.bin ~/poplar/bin/fastboot.bin
+
+
+================================================================================
+			FLASH INSTRUCTIONS
+================================================================================
+
+Two methods:
+
+Using USB debrick support:
+	Copy fastboot.bin to a FAT partition on the USB drive and reboot the
+       poplar board while pressing S3(usb_boot).
+
+       The system will execute the new u-boot and boot into a shell which you
+       can then use to write to eMMC.
+
+Using U-BOOT from shell:
+	1) using AXIS usb ethernet dongle and tftp
+	2) using FAT formated USB drive
+
+
+1. TFTP (USB ethernet dongle)
+=============================
+
+Plug a USB AXIS ethernet dongle on any of the USB2 ports on the Poplar board.
+Copy fastboot.bin to your tftp server.
+In u-boot make sure your network is properly setup.
+
+Then
+
+=> tftp 0x30000000 fastboot.bin
+starting USB...
+USB0:   USB EHCI 1.00
+scanning bus 0 for devices... 1 USB Device(s) found
+USB1:   USB EHCI 1.00
+scanning bus 1 for devices... 3 USB Device(s) found
+       scanning usb for storage devices... 0 Storage Device(s) found
+       scanning usb for ethernet devices... 1 Ethernet Device(s) found
+Waiting for Ethernet connection... done.
+Using asx0 device
+TFTP from server 192.168.1.4; our IP address is 192.168.1.10
+Filename 'poplar/fastboot.bin'.
+Load address: 0x30000000
+Loading: #################################################################
+	 #################################################################
+	 ###############################################################
+	 2 MiB/s
+done
+Bytes transferred = 983040 (f0000 hex)
+
+=> mmc write 0x30000000 0 0x780
+
+MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
+=> reset
+
+
+2. USING USB FAT DRIVE
+=======================
+
+Copy fastboot.bin to any partition on a FAT32 formated usb flash drive.
+Enter the uboot prompt
+
+=> fatls usb 0:2
+   983040   fastboot.bin
+
+1 file(s), 0 dir(s)
+
+=> fatload usb 0:2 0x30000000 fastboot.bin
+reading fastboot.bin
+983040 bytes read in 44 ms (21.3 MiB/s)
+
+=> mmc write 0x30000000 0 0x780
+
+MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
+
+
+================================================================================
+				BOOT TRACE
+================================================================================
+
+Bootrom start
+Boot Media: eMMC
+Decrypt auxiliary code ...OK
+
+lsadc voltage min: 000000FE, max: 000000FF, aver: 000000FE, index: 00000000
+
+Entry boot auxiliary code
+
+Auxiliary code - v1.00
+DDR code - V1.1.2 20160205
+Build: Mar 24 2016 - 17:09:44
+Reg Version:  v134
+Reg Time:     2016/03/18 09:44:55
+Reg Name:     hi3798cv2dmb_hi3798cv200_ddr3_2gbyte_8bitx4_4layers.reg
+
+Boot auxiliary code success
+Bootrom success
+
+LOADER:  Switched to aarch64 mode
+LOADER:  Entering ARM TRUSTED FIRMWARE
+LOADER:  CPU0 executes at 0x000ce000
+
+INFO:    BL1: 0xe1000 - 0xe7000 [size = 24576]
+NOTICE:  Booting Trusted Firmware
+NOTICE:  BL1: v1.3(debug):v1.3-372-g1ba9c60
+NOTICE:  BL1: Built : 17:51:33, Apr 30 2017
+INFO:    BL1: RAM 0xe1000 - 0xe7000
+INFO:    BL1: Loading BL2
+INFO:    Loading image id=1 at address 0xe9000
+INFO:    Image id=1 loaded at address 0xe9000, size = 0x5008
+NOTICE:  BL1: Booting BL2
+INFO:    Entry point address = 0xe9000
+INFO:    SPSR = 0x3c5
+NOTICE:  BL2: v1.3(debug):v1.3-372-g1ba9c60
+NOTICE:  BL2: Built : 17:51:33, Apr 30 2017
+INFO:    BL2: Loading BL31
+INFO:    Loading image id=3 at address 0x129000
+INFO:    Image id=3 loaded at address 0x129000, size = 0x8038
+INFO:    BL2: Loading BL33
+INFO:    Loading image id=5 at address 0x37000000
+INFO:    Image id=5 loaded at address 0x37000000, size = 0x58f17
+NOTICE:  BL1: Booting BL31
+INFO:    Entry point address = 0x129000
+INFO:    SPSR = 0x3cd
+INFO:    Boot bl33 from 0x37000000 for 364311 Bytes
+NOTICE:  BL31: v1.3(debug):v1.3-372-g1ba9c60
+NOTICE:  BL31: Built : 17:51:33, Apr 30 2017
+INFO:    BL31: Initializing runtime services
+INFO:    BL31: Preparing for EL3 exit to normal world
+INFO:    Entry point address = 0x37000000
+INFO:    SPSR = 0x3c9
+
+
+U-Boot 2017.05-rc2-00130-gd2255b0 (Apr 30 2017 - 17:51:28 +0200)poplar
+
+Model: HiSilicon Poplar Development Board
+BOARD: Hisilicon HI3798cv200 Poplar
+DRAM:  1 GiB
+MMC:   Hisilicon DWMMC: 0
+In:    serial at f8b00000
+Out:   serial at f8b00000
+Err:   serial at f8b00000
+Net:   Net Initialization Skipped
+No ethernet found.
+
+Hit any key to stop autoboot:  0
+starting USB...
+USB0:   USB EHCI 1.00
+scanning bus 0 for devices... 1 USB Device(s) found
+USB1:   USB EHCI 1.00
+scanning bus 1 for devices... 4 USB Device(s) found
+       scanning usb for storage devices... 1 Storage Device(s) found
+       scanning usb for ethernet devices... 1 Ethernet Device(s) found
+
+USB device 0:
+    Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade
+	    Type: Removable Hard Disk
+	    Capacity: 7632.0 MB = 7.4 GB (15630336 x 512)
+... is now current device
+Scanning usb 0:1...
+=>
diff --git a/board/hisilicon/poplar/poplar.c b/board/hisilicon/poplar/poplar.c
new file mode 100644
index 0000000..d542f68
--- /dev/null
+++ b/board/hisilicon/poplar/poplar.c
@@ -0,0 +1,174 @@
+/*
+ * (C) Copyright 2017 Linaro
+ * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <dm.h>
+#include <common.h>
+#include <asm/io.h>
+#include <dm/platform_data/serial_pl01x.h>
+#include <asm/arch/hi3798cv200.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/armv8/mmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct mm_region poplar_mem_map[] = {
+	{
+		.virt = 0x0UL,
+		.phys = 0x0UL,
+		.size = 0x80000000UL,
+		.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+			 PTE_BLOCK_INNER_SHARE
+	}, {
+		.virt = 0x80000000UL,
+		.phys = 0x80000000UL,
+		.size = 0x80000000UL,
+		.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+			 PTE_BLOCK_NON_SHARE |
+			 PTE_BLOCK_PXN | PTE_BLOCK_UXN
+	}, {
+		0,
+	}
+};
+
+struct mm_region *mem_map = poplar_mem_map;
+
+static const struct pl01x_serial_platdata serial_platdata = {
+	.base = REG_BASE_UART0,
+	.type = TYPE_PL010,
+	.clock = 75000000,
+};
+
+U_BOOT_DEVICE(poplar_serial) = {
+	.name = "serial_pl01x",
+	.platdata = &serial_platdata,
+};
+
+int checkboard(void)
+{
+	puts("BOARD: Hisilicon HI3798cv200 Poplar\n");
+
+	return 0;
+}
+
+void reset_cpu(ulong addr)
+{
+	psci_system_reset();
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size(NULL, 0x80000000);
+
+	return 0;
+}
+
+/*
+ * Some linux kernel versions don't use memory before its load address, so to
+ * be generic we just pretend it isn't there.  In previous uboot versions we
+ * carved the space used by BL31 (runs in DDR on this platfomr) so the PSCI code
+ * could persist in memory and be left alone by the kernel.
+ *
+ * That led to a problem when mapping memory in older kernels.  That PSCI code
+ * now lies in memory below the kernel load offset; it therefore won't be
+ * touched by the kernel, and by not specially reserving it we avoid the mapping
+ * problem as well.
+ *
+ */
+#define KERNEL_TEXT_OFFSET	0x00080000
+
+int dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = KERNEL_TEXT_OFFSET;
+	gd->bd->bi_dram[0].size = gd->ram_size - gd->bd->bi_dram[0].start;
+
+	return 0;
+}
+
+static void usb2_phy_config(void)
+{
+	const u32 config[] = {
+		/* close EOP pre-emphasis. open data pre-emphasis */
+		0xa1001c,
+		/* Rcomp = 150mW, increase DC level */
+		0xa00607,
+		/* keep Rcomp working */
+		0xa10700,
+		/* Icomp = 212mW, increase current drive */
+		0xa00aab,
+		/* EMI fix: rx_active not stay 1 when error packets received */
+		0xa11140,
+		/* Comp mode select */
+		0xa11041,
+		/* adjust eye diagram */
+		0xa0098c,
+		/* adjust eye diagram */
+		0xa10a0a,
+	};
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(config); i++) {
+		writel(config[i], PERI_CTRL_USB0);
+		clrsetbits_le32(PERI_CTRL_USB0, BIT(21), BIT(20) | BIT(22));
+		udelay(20);
+	}
+}
+
+static void usb2_phy_init(void)
+{
+	/* reset usb2 controller bus/utmi/roothub */
+	setbits_le32(PERI_CRG46, USB2_BUS_SRST_REQ | USB2_UTMI0_SRST_REQ |
+			USB2_HST_PHY_SYST_REQ | USB2_OTG_PHY_SYST_REQ);
+	udelay(200);
+
+	/* reset usb2 phy por/utmi */
+	setbits_le32(PERI_CRG47, USB2_PHY01_SRST_REQ | USB2_PHY01_SRST_TREQ1);
+	udelay(200);
+
+	/* open usb2 ref clk */
+	setbits_le32(PERI_CRG47, USB2_PHY01_REF_CKEN);
+	udelay(300);
+
+	/* cancel usb2 power on reset */
+	clrbits_le32(PERI_CRG47, USB2_PHY01_SRST_REQ);
+	udelay(500);
+
+	usb2_phy_config();
+
+	/* cancel usb2 port reset, wait comp circuit stable */
+	clrbits_le32(PERI_CRG47, USB2_PHY01_SRST_TREQ1);
+	mdelay(10);
+
+	/* open usb2 controller clk */
+	setbits_le32(PERI_CRG46, USB2_BUS_CKEN | USB2_OHCI48M_CKEN |
+			USB2_OHCI12M_CKEN | USB2_OTG_UTMI_CKEN |
+			USB2_HST_PHY_CKEN | USB2_UTMI0_CKEN);
+	udelay(200);
+
+	/* cancel usb2 control reset */
+	clrbits_le32(PERI_CRG46, USB2_BUS_SRST_REQ | USB2_UTMI0_SRST_REQ |
+			USB2_HST_PHY_SYST_REQ | USB2_OTG_PHY_SYST_REQ);
+	udelay(200);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+
+	ret = hi6220_dwmci_add_port(0, REG_BASE_MCI, 8);
+	if (ret)
+		printf("mmc init error (%d)\n", ret);
+
+	return ret;
+}
+
+int board_init(void)
+{
+	usb2_phy_init();
+
+	return 0;
+}
+
diff --git a/configs/poplar_defconfig b/configs/poplar_defconfig
new file mode 100644
index 0000000..8f9f40f
--- /dev/null
+++ b/configs/poplar_defconfig
@@ -0,0 +1,26 @@
+CONFIG_ARM=y
+CONFIG_TARGET_POPLAR=y
+CONFIG_IDENT_STRING="poplar"
+CONFIG_DEFAULT_DEVICE_TREE="hi3798cv200-poplar"
+CONFIG_SYS_PROMPT="poplar# "
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_DISPLAY_CPUINFO=n
+CONFIG_DISPLAY_BOARDINFO=y
+CONFIG_ISO_PARTITION=n
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_K3=y
+CONFIG_PL011_SERIAL=y
+CONFIG_PSCI_RESET=y
+CONFIG_USB=y
+CONFIG_USB_EHCI=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_STORAGE=y
+CONFIG_NET=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_DM_GPIO is not set
+CONFIG_LIB_RAND=y
+CONFIG_CMD_UNZIP=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+
diff --git a/include/configs/poplar.h b/include/configs/poplar.h
new file mode 100644
index 0000000..55e05d6
--- /dev/null
+++ b/include/configs/poplar.h
@@ -0,0 +1,86 @@
+/*
+ * (C) Copyright 2017 Linaro
+ *
+ * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
+ *
+ * Configuration for Poplar 96boards CE. Parts were derived from other ARM
+ * configurations.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _POPLAR_H_
+#define _POPLAR_H_
+
+#include <linux/sizes.h>
+
+/* DRAM banks */
+#define CONFIG_NR_DRAM_BANKS			2
+
+/* SYS */
+#define CONFIG_SYS_BOOTM_LEN			0x1400000
+#define CONFIG_SYS_INIT_SP_ADDR			0x200000
+#define CONFIG_SYS_LOAD_ADDR			0x800000
+#define CONFIG_SYS_MALLOC_LEN			SZ_32M
+
+/* ATF bl33.bin load address (must match) */
+#define CONFIG_SYS_TEXT_BASE			0x37000000
+
+/* PL010/PL011 */
+#define CONFIG_PL01X_SERIAL
+
+/* USB configuration */
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
+#define CONFIG_USB_MAX_CONTROLLER_COUNT		2
+#define CONFIG_SYS_USB_EVENT_POLL
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+
+/* SD/MMC */
+#define CONFIG_BOUNCE_BUFFER
+
+/*****************************************************************************
+ *  Initial environment variables
+ *****************************************************************************/
+
+#define BOOT_TARGET_DEVICES(func)					\
+					func(USB, usb, 0)		\
+					func(MMC, mmc, 0)		\
+					func(DHCP, dhcp, na)
+#ifndef CONFIG_SPL_BUILD
+#include <config_distro_defaults.h>
+#include <config_distro_bootcmd.h>
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+			"loader_mmc_blknum=0x0\0"			\
+			"loader_mmc_nblks=0x780\0"			\
+			"env_mmc_blknum=0x780\0"			\
+			"env_mmc_nblks=0x80\0"				\
+			"kernel_addr_r=0x30000000\0"			\
+			"pxefile_addr_r=0x32000000\0"			\
+			"scriptaddr=0x32000000\0"			\
+			"fdt_addr_r=0x32200000\0"			\
+			"fdtfile=hisilicon/hi3798cv200-poplar.dtb\0"	\
+			"ramdisk_addr_r=0x32400000\0"			\
+			BOOTENV
+
+
+/* Command line configuration */
+#define CONFIG_ENV_IS_IN_MMC		1
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_OFFSET		(0x780 * 512)	/* env_mmc_blknum */
+#define CONFIG_ENV_SIZE			0x10000	/* env_mmc_nblks bytes */
+#define CONFIG_FAT_WRITE
+#define CONFIG_ENV_VARS_UBOOT_CONFIG
+
+/* Monitor Command Prompt */
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_CBSIZE		512
+#define CONFIG_SYS_MAXARGS		64
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+
+#endif /* _POPLAR_H_ */
-- 
2.7.4

[U-Boot] [PATCHv6 3/3] ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards

[Jorge Ramirez]

On 06/26/2017 03:52 PM, Jorge Ramirez-Ortiz wrote:
> This port adds support for:
>          1) Serial
>          2) eMMC
>          3) USB
>
> It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
> BL33 executable [see board's README]


FYI, I just submitted the Pull Request to the arm trusted firmware project:
https://github.com/ARM-software/arm-trusted-firmware/pull/1005/commits/420eabe76eb0a23314b21044f4387464df79d38f


>
> eMMC has been tested for reading and booting the loader and linux
> kernels as well as saving the u-boot environment.
>
> USB has been tested with ASIX networking adapter and SanDisk 7.4GB
> drive.
>
> PSCI has been tested via the reset call (PSCI executes from DDR)
>
> The firwmare upgrade process has been tested via TFTP and USB FAT
> filesystem containing the fastboot.bin image in one of the partitions.
>
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> ---
>   arch/arm/Kconfig                                   |  14 +
>   arch/arm/dts/hi3798cv200-u-boot.dtsi               |  29 +++
>   arch/arm/include/asm/arch-hi3798cv200/dwmmc.h      |  13 +
>   .../arm/include/asm/arch-hi3798cv200/hi3798cv200.h |  50 ++++
>   board/hisilicon/poplar/Kconfig                     |  15 ++
>   board/hisilicon/poplar/MAINTAINERS                 |   6 +
>   board/hisilicon/poplar/Makefile                    |   7 +
>   board/hisilicon/poplar/README                      | 288 +++++++++++++++++++++
>   board/hisilicon/poplar/poplar.c                    | 174 +++++++++++++
>   configs/poplar_defconfig                           |  26 ++
>   include/configs/poplar.h                           |  86 ++++++
>   11 files changed, 708 insertions(+)
>   create mode 100644 arch/arm/dts/hi3798cv200-u-boot.dtsi
>   create mode 100644 arch/arm/include/asm/arch-hi3798cv200/dwmmc.h
>   create mode 100644 arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h
>   create mode 100644 board/hisilicon/poplar/Kconfig
>   create mode 100644 board/hisilicon/poplar/MAINTAINERS
>   create mode 100644 board/hisilicon/poplar/Makefile
>   create mode 100644 board/hisilicon/poplar/README
>   create mode 100644 board/hisilicon/poplar/poplar.c
>   create mode 100644 configs/poplar_defconfig
>   create mode 100644 include/configs/poplar.h
>
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index 46183ae..4b4f51c 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -837,6 +837,19 @@ config TARGET_HIKEY
>   	  Support for HiKey 96boards platform. It features a HI6220
>   	  SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.
>   
> +config TARGET_POPLAR
> +	bool "Support Poplar 96boards Enterprise Edition Platform"
> +	select ARM64
> +	select DM
> +	select OF_CONTROL
> +	select DM_SERIAL
> +	select DM_USB
> +	  help
> +	  Support for Poplar 96boards EE platform. It features a HI3798cv200
> +	  SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU
> +	  making it capable of running any commercial set-top solution based on
> +	  Linux or Android.
> +
>   config TARGET_LS1012AQDS
>   	bool "Support ls1012aqds"
>   	select ARCH_LS1012A
> @@ -1165,6 +1178,7 @@ source "board/grinn/chiliboard/Kconfig"
>   source "board/gumstix/pepper/Kconfig"
>   source "board/h2200/Kconfig"
>   source "board/hisilicon/hikey/Kconfig"
> +source "board/hisilicon/poplar/Kconfig"
>   source "board/imx31_phycore/Kconfig"
>   source "board/isee/igep003x/Kconfig"
>   source "board/olimex/mx23_olinuxino/Kconfig"
> diff --git a/arch/arm/dts/hi3798cv200-u-boot.dtsi b/arch/arm/dts/hi3798cv200-u-boot.dtsi
> new file mode 100644
> index 0000000..2b3713b
> --- /dev/null
> +++ b/arch/arm/dts/hi3798cv200-u-boot.dtsi
> @@ -0,0 +1,29 @@
> +/*
> + * U-Boot addition to:
> + *  1) use platform data for the console
> + *  2) provide support for the generic-ehci USB driver currently not available
> + *     in the linux kernel (8/May/2017).
> + *
> + * (C) Copyright 2017 Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> + *
> + * SPDX-License-Identifier:     GPL-2.0+
> + */
> +
> +&soc {
> +	usb2: ehci at 9890000 {
> +		compatible = "generic-ehci";
> +		reg = <0x9890000 0x100>;
> +		status = "okay";
> +	};
> +};
> +
> +&uart0 {
> +	status = "disabled";
> +};
> +
> +/{
> +	chosen {
> +		stdout-path = "";
> +	};
> +};
> +
> diff --git a/arch/arm/include/asm/arch-hi3798cv200/dwmmc.h b/arch/arm/include/asm/arch-hi3798cv200/dwmmc.h
> new file mode 100644
> index 0000000..1060d94
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-hi3798cv200/dwmmc.h
> @@ -0,0 +1,13 @@
> +/*
> + * (C) Copyright 2017 Linaro
> + * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#ifndef _HI3798cv200_DWMMC_H_
> +#define _HI3798cv200_DWMMC_H_
> +
> +int hi6220_dwmci_add_port(int index, u32 regbase, int bus_width);
> +
> +#endif /* _HI3798cv200_DWMMC_H_ */
> diff --git a/arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h b/arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h
> new file mode 100644
> index 0000000..d30e0b4
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h
> @@ -0,0 +1,50 @@
> +/*
> + * (C) Copyright 2017 Linaro
> + * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#ifndef __HI3798cv200_H__
> +#define __HI3798cv200_H__
> +
> +#define REG_BASE_PERI_CTRL		0xF8A20000
> +#define REG_BASE_CRG			0xF8A22000
> +
> +/* DEVICES */
> +#define REG_BASE_MCI			0xF9830000
> +#define REG_BASE_UART0			0xF8B00000
> +
> +/* PERI control registers (4KB) */
> +	/* USB2 PHY01 configuration register */
> +#define PERI_CTRL_USB0			(REG_BASE_PERI_CTRL + 0x120)
> +
> +/* PERI CRG registers (4KB) */
> +	/* USB2 CTRL0 clock and soft reset */
> +#define PERI_CRG46			(REG_BASE_CRG + 0xb8)
> +#define USB2_BUS_CKEN			(1<<0)
> +#define USB2_OHCI48M_CKEN		(1<<1)
> +#define USB2_OHCI12M_CKEN		(1<<2)
> +#define USB2_OTG_UTMI_CKEN		(1<<3)
> +#define USB2_HST_PHY_CKEN		(1<<4)
> +#define USB2_UTMI0_CKEN			(1<<5)
> +#define USB2_BUS_SRST_REQ		(1<<12)
> +#define USB2_UTMI0_SRST_REQ		(1<<13)
> +#define USB2_HST_PHY_SYST_REQ		(1<<16)
> +#define USB2_OTG_PHY_SYST_REQ		(1<<17)
> +#define USB2_CLK48_SEL			(1<<20)
> +
> +	/* USB2 PHY clock and soft reset */
> +#define PERI_CRG47			(REG_BASE_CRG + 0xbc)
> +#define USB2_PHY01_REF_CKEN		(1 << 0)
> +#define USB2_PHY2_REF_CKEN		(1 << 2)
> +#define USB2_PHY01_SRST_REQ		(1 << 4)
> +#define USB2_PHY2_SRST_REQ		(1 << 6)
> +#define USB2_PHY01_SRST_TREQ0		(1 << 8)
> +#define USB2_PHY01_SRST_TREQ1		(1 << 9)
> +#define USB2_PHY2_SRST_TREQ		(1 << 10)
> +#define USB2_PHY01_REFCLK_SEL		(1 << 12)
> +#define USB2_PHY2_REFCLK_SEL		(1 << 14)
> +
> +
> +#endif
> diff --git a/board/hisilicon/poplar/Kconfig b/board/hisilicon/poplar/Kconfig
> new file mode 100644
> index 0000000..3397295
> --- /dev/null
> +++ b/board/hisilicon/poplar/Kconfig
> @@ -0,0 +1,15 @@
> +if TARGET_POPLAR
> +
> +config SYS_BOARD
> +	default "poplar"
> +
> +config SYS_VENDOR
> +	default "hisilicon"
> +
> +config SYS_SOC
> +	default "hi3798cv200"
> +
> +config SYS_CONFIG_NAME
> +	default "poplar"
> +
> +endif
> diff --git a/board/hisilicon/poplar/MAINTAINERS b/board/hisilicon/poplar/MAINTAINERS
> new file mode 100644
> index 0000000..0cc01c8
> --- /dev/null
> +++ b/board/hisilicon/poplar/MAINTAINERS
> @@ -0,0 +1,6 @@
> +Poplar BOARD
> +M:     Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> +S:     Maintained
> +F:     board/hisilicon/poplar
> +F:     include/configs/poplar.h
> +F:     configs/poplar_defconfig
> diff --git a/board/hisilicon/poplar/Makefile b/board/hisilicon/poplar/Makefile
> new file mode 100644
> index 0000000..101545d
> --- /dev/null
> +++ b/board/hisilicon/poplar/Makefile
> @@ -0,0 +1,7 @@
> +#
> +# (C) Copyright 2017 Linaro
> +# Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> +#
> +# SPDX-License-Identifier:	GPL-2.0+
> +#
> +obj-y	:= poplar.o
> diff --git a/board/hisilicon/poplar/README b/board/hisilicon/poplar/README
> new file mode 100644
> index 0000000..99ed6ce
> --- /dev/null
> +++ b/board/hisilicon/poplar/README
> @@ -0,0 +1,288 @@
> +================================================================================
> +			Board Information
> +================================================================================
> +
> +Developed by HiSilicon, the board features the Hi3798C V200 with an
> +integrated quad-core 64-bit ARM Cortex A53 processor and high
> +performance Mali T720 GPU, making it capable of running any commercial
> +set-top solution based on Linux or Android. Its high performance
> +specification also supports a premium user experience with up to H.265
> +HEVC decoding of 4K video at 60 frames per second.
> +
> +SOC  Hisilicon Hi3798CV200
> +CPU  Quad-core ARM Cortex-A53 64 bit
> +DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB
> +USB  Two USB 2.0 ports One USB 3.0 ports
> +CONSOLE  USB-micro port for console support
> +ETHERNET  1 GBe Ethernet
> +PCIE  One PCIe 2.0 interfaces
> +JTAG  8-Pin JTAG
> +EXPANSION INTERFACE  Linaro 96Boards Low Speed Expansion slot
> +DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor
> +WIFI  802.11AC 2*2 with Bluetooth
> +CONNECTORS  One connector for Smart Card One connector for TSI
> +
> +
> +================================================================================
> +			BUILD INSTRUCTIONS
> +================================================================================
> +
> +Note of warning:
> +================
> +
> +U-boot has a *strong* dependency with the l-loader and the arm trusted firmware
> +repositories.
> +
> +The boot sequence is:
> +	l-loader --> arm_trusted_firmware --> u-boot
> +
> +U-Boot needs to be aware of the BL31 runtime location and size to avoid writing
> +over it. Currently, BL31 is being placed below the kernel text offset (check
> +poplar.c) but this could change in the future.
> +
> +The current version of u-boot has been tested with:
> + - https://github.com/Linaro/poplar-l-loader.git
> +
> +	commit f0988698dcc5c08bd0a8f50aa0457e138a5f438c
> +	Author: Alex Elder <elder@linaro.org>
> +	Date:   Fri Jun 16 08:57:59 2017 -0500
> +
> +    l-loader: use external memory region definitions
> +
> +    The ARM Trusted Firmware code now has a header file that collects
> +    all the definitions for the memory regions used for its boot stages.
> +    Include that file where needed, and use the definitions found therein
> +
> +    Signed-off-by: Alex Elder <elder@linaro.org>
> +
> +
> + - https://github.com/Linaro/poplar-arm-trusted-firmware.git
> +
> +	commit 6ac42dd3be13c99aa8ce29a15073e2f19d935f68
> +	Author: Alex Elder <elder@linaro.org>
> +	Date:   Fri Jun 16 09:24:50 2017 -0500
> +
> +    poplar: define memory regions in a separate file
> +
> +    Separate the definitions for memory regions used for the BL stage
> +    images and FIP into a new file.  The "l-loader" image uses knowledge
> +    of the sizes and locations of these memory regions, and it can now
> +    include this (external) header to get these definitions, rather than
> +    having to make coordinated changes to both code bases.
> +
> +    The new file has a complete set of definitions (more than may be
> +    required by one or the other user).  It also includes a summary of
> +    how the boot process works, and how it uses these regions.
> +
> +    It should now be relatively easy to adjust the sizes and locations
> +    of these memory regions, or to add to them (e.g. for TEE).
> +
> +    Signed-off-by: Alex Elder <elder@linaro.org>
> +
> +
> +Compile from source:
> +====================
> +
> +Get all the sources
> +
> +  > mkdir -p ~/poplar/src ~/poplar/bin
> +  > cd ~/poplar/src
> +  > git clone https://github.com/Linaro/poplar-l-loader.git l-loader
> +  > git clone https://github.com/Linaro/poplar-arm-trusted-firmware.git atf
> +  > git clone https://github.com/Linaro/poplar-u-boot.git u-boot
> +
> +Make sure you are using the correct branch on each one of these repositories.
> +The definition of "correct" might change over time (at this moment in time this
> +would be the "latest" branch).
> +
> +Compile U-Boot:
> +===============
> +
> +  Prerequisite:
> +  # sudo apt-get install device-tree-compiler
> +
> +  > cd ~/poplar/src/u-boot
> +  > make CROSS_COMPILE=aarch64-linux-gnu- poplar_defconfig
> +  > make CROSS_COMPILE=aarch64-linux-gnu-
> +  > cp u-boot.bin ~/poplar/bin
> +
> +Compile ARM Trusted Firmware (ATF):
> +===================================
> +
> +  > cd ~/poplar/src/atf
> +  > make CROSS_COMPILE=aarch64-linux-gnu- all fip \
> +		SPD=none BL33=~/poplar/bin/u-boot.bin DEBUG=1 PLAT=poplar
> +
> +Copy resulting binaries
> +  > cp build/hi3798cv200/debug/bl1.bin ~/poplar/src/l-loader/atf/
> +  > cp build/hi3798cv200/debug/fip.bin ~/poplar/src/l-loader/atf/
> +
> +Compile l-loader:
> +=================
> +
> +  > cd ~/poplar/src/l-loader
> +  > make clean
> +  > make CROSS_COMPILE=arm-linux-gnueabi-
> +
> +   Due to BootROM requiremets, rename l-loader.bin to fastboot.bin:
> +  > cp l-loader.bin ~/poplar/bin/fastboot.bin
> +
> +
> +================================================================================
> +			FLASH INSTRUCTIONS
> +================================================================================
> +
> +Two methods:
> +
> +Using USB debrick support:
> +	Copy fastboot.bin to a FAT partition on the USB drive and reboot the
> +       poplar board while pressing S3(usb_boot).
> +
> +       The system will execute the new u-boot and boot into a shell which you
> +       can then use to write to eMMC.
> +
> +Using U-BOOT from shell:
> +	1) using AXIS usb ethernet dongle and tftp
> +	2) using FAT formated USB drive
> +
> +
> +1. TFTP (USB ethernet dongle)
> +=============================
> +
> +Plug a USB AXIS ethernet dongle on any of the USB2 ports on the Poplar board.
> +Copy fastboot.bin to your tftp server.
> +In u-boot make sure your network is properly setup.
> +
> +Then
> +
> +=> tftp 0x30000000 fastboot.bin
> +starting USB...
> +USB0:   USB EHCI 1.00
> +scanning bus 0 for devices... 1 USB Device(s) found
> +USB1:   USB EHCI 1.00
> +scanning bus 1 for devices... 3 USB Device(s) found
> +       scanning usb for storage devices... 0 Storage Device(s) found
> +       scanning usb for ethernet devices... 1 Ethernet Device(s) found
> +Waiting for Ethernet connection... done.
> +Using asx0 device
> +TFTP from server 192.168.1.4; our IP address is 192.168.1.10
> +Filename 'poplar/fastboot.bin'.
> +Load address: 0x30000000
> +Loading: #################################################################
> +	 #################################################################
> +	 ###############################################################
> +	 2 MiB/s
> +done
> +Bytes transferred = 983040 (f0000 hex)
> +
> +=> mmc write 0x30000000 0 0x780
> +
> +MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
> +=> reset
> +
> +
> +2. USING USB FAT DRIVE
> +=======================
> +
> +Copy fastboot.bin to any partition on a FAT32 formated usb flash drive.
> +Enter the uboot prompt
> +
> +=> fatls usb 0:2
> +   983040   fastboot.bin
> +
> +1 file(s), 0 dir(s)
> +
> +=> fatload usb 0:2 0x30000000 fastboot.bin
> +reading fastboot.bin
> +983040 bytes read in 44 ms (21.3 MiB/s)
> +
> +=> mmc write 0x30000000 0 0x780
> +
> +MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
> +
> +
> +================================================================================
> +				BOOT TRACE
> +================================================================================
> +
> +Bootrom start
> +Boot Media: eMMC
> +Decrypt auxiliary code ...OK
> +
> +lsadc voltage min: 000000FE, max: 000000FF, aver: 000000FE, index: 00000000
> +
> +Entry boot auxiliary code
> +
> +Auxiliary code - v1.00
> +DDR code - V1.1.2 20160205
> +Build: Mar 24 2016 - 17:09:44
> +Reg Version:  v134
> +Reg Time:     2016/03/18 09:44:55
> +Reg Name:     hi3798cv2dmb_hi3798cv200_ddr3_2gbyte_8bitx4_4layers.reg
> +
> +Boot auxiliary code success
> +Bootrom success
> +
> +LOADER:  Switched to aarch64 mode
> +LOADER:  Entering ARM TRUSTED FIRMWARE
> +LOADER:  CPU0 executes at 0x000ce000
> +
> +INFO:    BL1: 0xe1000 - 0xe7000 [size = 24576]
> +NOTICE:  Booting Trusted Firmware
> +NOTICE:  BL1: v1.3(debug):v1.3-372-g1ba9c60
> +NOTICE:  BL1: Built : 17:51:33, Apr 30 2017
> +INFO:    BL1: RAM 0xe1000 - 0xe7000
> +INFO:    BL1: Loading BL2
> +INFO:    Loading image id=1 at address 0xe9000
> +INFO:    Image id=1 loaded at address 0xe9000, size = 0x5008
> +NOTICE:  BL1: Booting BL2
> +INFO:    Entry point address = 0xe9000
> +INFO:    SPSR = 0x3c5
> +NOTICE:  BL2: v1.3(debug):v1.3-372-g1ba9c60
> +NOTICE:  BL2: Built : 17:51:33, Apr 30 2017
> +INFO:    BL2: Loading BL31
> +INFO:    Loading image id=3 at address 0x129000
> +INFO:    Image id=3 loaded at address 0x129000, size = 0x8038
> +INFO:    BL2: Loading BL33
> +INFO:    Loading image id=5 at address 0x37000000
> +INFO:    Image id=5 loaded at address 0x37000000, size = 0x58f17
> +NOTICE:  BL1: Booting BL31
> +INFO:    Entry point address = 0x129000
> +INFO:    SPSR = 0x3cd
> +INFO:    Boot bl33 from 0x37000000 for 364311 Bytes
> +NOTICE:  BL31: v1.3(debug):v1.3-372-g1ba9c60
> +NOTICE:  BL31: Built : 17:51:33, Apr 30 2017
> +INFO:    BL31: Initializing runtime services
> +INFO:    BL31: Preparing for EL3 exit to normal world
> +INFO:    Entry point address = 0x37000000
> +INFO:    SPSR = 0x3c9
> +
> +
> +U-Boot 2017.05-rc2-00130-gd2255b0 (Apr 30 2017 - 17:51:28 +0200)poplar
> +
> +Model: HiSilicon Poplar Development Board
> +BOARD: Hisilicon HI3798cv200 Poplar
> +DRAM:  1 GiB
> +MMC:   Hisilicon DWMMC: 0
> +In:    serial at f8b00000
> +Out:   serial at f8b00000
> +Err:   serial at f8b00000
> +Net:   Net Initialization Skipped
> +No ethernet found.
> +
> +Hit any key to stop autoboot:  0
> +starting USB...
> +USB0:   USB EHCI 1.00
> +scanning bus 0 for devices... 1 USB Device(s) found
> +USB1:   USB EHCI 1.00
> +scanning bus 1 for devices... 4 USB Device(s) found
> +       scanning usb for storage devices... 1 Storage Device(s) found
> +       scanning usb for ethernet devices... 1 Ethernet Device(s) found
> +
> +USB device 0:
> +    Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade
> +	    Type: Removable Hard Disk
> +	    Capacity: 7632.0 MB = 7.4 GB (15630336 x 512)
> +... is now current device
> +Scanning usb 0:1...
> +=>
> diff --git a/board/hisilicon/poplar/poplar.c b/board/hisilicon/poplar/poplar.c
> new file mode 100644
> index 0000000..d542f68
> --- /dev/null
> +++ b/board/hisilicon/poplar/poplar.c
> @@ -0,0 +1,174 @@
> +/*
> + * (C) Copyright 2017 Linaro
> + * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#include <dm.h>
> +#include <common.h>
> +#include <asm/io.h>
> +#include <dm/platform_data/serial_pl01x.h>
> +#include <asm/arch/hi3798cv200.h>
> +#include <asm/arch/dwmmc.h>
> +#include <asm/armv8/mmu.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +static struct mm_region poplar_mem_map[] = {
> +	{
> +		.virt = 0x0UL,
> +		.phys = 0x0UL,
> +		.size = 0x80000000UL,
> +		.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
> +			 PTE_BLOCK_INNER_SHARE
> +	}, {
> +		.virt = 0x80000000UL,
> +		.phys = 0x80000000UL,
> +		.size = 0x80000000UL,
> +		.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
> +			 PTE_BLOCK_NON_SHARE |
> +			 PTE_BLOCK_PXN | PTE_BLOCK_UXN
> +	}, {
> +		0,
> +	}
> +};
> +
> +struct mm_region *mem_map = poplar_mem_map;
> +
> +static const struct pl01x_serial_platdata serial_platdata = {
> +	.base = REG_BASE_UART0,
> +	.type = TYPE_PL010,
> +	.clock = 75000000,
> +};
> +
> +U_BOOT_DEVICE(poplar_serial) = {
> +	.name = "serial_pl01x",
> +	.platdata = &serial_platdata,
> +};
> +
> +int checkboard(void)
> +{
> +	puts("BOARD: Hisilicon HI3798cv200 Poplar\n");
> +
> +	return 0;
> +}
> +
> +void reset_cpu(ulong addr)
> +{
> +	psci_system_reset();
> +}
> +
> +int dram_init(void)
> +{
> +	gd->ram_size = get_ram_size(NULL, 0x80000000);
> +
> +	return 0;
> +}
> +
> +/*
> + * Some linux kernel versions don't use memory before its load address, so to
> + * be generic we just pretend it isn't there.  In previous uboot versions we
> + * carved the space used by BL31 (runs in DDR on this platfomr) so the PSCI code
> + * could persist in memory and be left alone by the kernel.
> + *
> + * That led to a problem when mapping memory in older kernels.  That PSCI code
> + * now lies in memory below the kernel load offset; it therefore won't be
> + * touched by the kernel, and by not specially reserving it we avoid the mapping
> + * problem as well.
> + *
> + */
> +#define KERNEL_TEXT_OFFSET	0x00080000
> +
> +int dram_init_banksize(void)
> +{
> +	gd->bd->bi_dram[0].start = KERNEL_TEXT_OFFSET;
> +	gd->bd->bi_dram[0].size = gd->ram_size - gd->bd->bi_dram[0].start;
> +
> +	return 0;
> +}
> +
> +static void usb2_phy_config(void)
> +{
> +	const u32 config[] = {
> +		/* close EOP pre-emphasis. open data pre-emphasis */
> +		0xa1001c,
> +		/* Rcomp = 150mW, increase DC level */
> +		0xa00607,
> +		/* keep Rcomp working */
> +		0xa10700,
> +		/* Icomp = 212mW, increase current drive */
> +		0xa00aab,
> +		/* EMI fix: rx_active not stay 1 when error packets received */
> +		0xa11140,
> +		/* Comp mode select */
> +		0xa11041,
> +		/* adjust eye diagram */
> +		0xa0098c,
> +		/* adjust eye diagram */
> +		0xa10a0a,
> +	};
> +	int i;
> +
> +	for (i = 0; i < ARRAY_SIZE(config); i++) {
> +		writel(config[i], PERI_CTRL_USB0);
> +		clrsetbits_le32(PERI_CTRL_USB0, BIT(21), BIT(20) | BIT(22));
> +		udelay(20);
> +	}
> +}
> +
> +static void usb2_phy_init(void)
> +{
> +	/* reset usb2 controller bus/utmi/roothub */
> +	setbits_le32(PERI_CRG46, USB2_BUS_SRST_REQ | USB2_UTMI0_SRST_REQ |
> +			USB2_HST_PHY_SYST_REQ | USB2_OTG_PHY_SYST_REQ);
> +	udelay(200);
> +
> +	/* reset usb2 phy por/utmi */
> +	setbits_le32(PERI_CRG47, USB2_PHY01_SRST_REQ | USB2_PHY01_SRST_TREQ1);
> +	udelay(200);
> +
> +	/* open usb2 ref clk */
> +	setbits_le32(PERI_CRG47, USB2_PHY01_REF_CKEN);
> +	udelay(300);
> +
> +	/* cancel usb2 power on reset */
> +	clrbits_le32(PERI_CRG47, USB2_PHY01_SRST_REQ);
> +	udelay(500);
> +
> +	usb2_phy_config();
> +
> +	/* cancel usb2 port reset, wait comp circuit stable */
> +	clrbits_le32(PERI_CRG47, USB2_PHY01_SRST_TREQ1);
> +	mdelay(10);
> +
> +	/* open usb2 controller clk */
> +	setbits_le32(PERI_CRG46, USB2_BUS_CKEN | USB2_OHCI48M_CKEN |
> +			USB2_OHCI12M_CKEN | USB2_OTG_UTMI_CKEN |
> +			USB2_HST_PHY_CKEN | USB2_UTMI0_CKEN);
> +	udelay(200);
> +
> +	/* cancel usb2 control reset */
> +	clrbits_le32(PERI_CRG46, USB2_BUS_SRST_REQ | USB2_UTMI0_SRST_REQ |
> +			USB2_HST_PHY_SYST_REQ | USB2_OTG_PHY_SYST_REQ);
> +	udelay(200);
> +}
> +
> +int board_mmc_init(bd_t *bis)
> +{
> +	int ret;
> +
> +	ret = hi6220_dwmci_add_port(0, REG_BASE_MCI, 8);
> +	if (ret)
> +		printf("mmc init error (%d)\n", ret);
> +
> +	return ret;
> +}
> +
> +int board_init(void)
> +{
> +	usb2_phy_init();
> +
> +	return 0;
> +}
> +
> diff --git a/configs/poplar_defconfig b/configs/poplar_defconfig
> new file mode 100644
> index 0000000..8f9f40f
> --- /dev/null
> +++ b/configs/poplar_defconfig
> @@ -0,0 +1,26 @@
> +CONFIG_ARM=y
> +CONFIG_TARGET_POPLAR=y
> +CONFIG_IDENT_STRING="poplar"
> +CONFIG_DEFAULT_DEVICE_TREE="hi3798cv200-poplar"
> +CONFIG_SYS_PROMPT="poplar# "
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_DISPLAY_CPUINFO=n
> +CONFIG_DISPLAY_BOARDINFO=y
> +CONFIG_ISO_PARTITION=n
> +CONFIG_MMC_DW=y
> +CONFIG_MMC_DW_K3=y
> +CONFIG_PL011_SERIAL=y
> +CONFIG_PSCI_RESET=y
> +CONFIG_USB=y
> +CONFIG_USB_EHCI=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_NET=y
> +# CONFIG_CMD_IMLS is not set
> +# CONFIG_DM_GPIO is not set
> +CONFIG_LIB_RAND=y
> +CONFIG_CMD_UNZIP=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
> +
> diff --git a/include/configs/poplar.h b/include/configs/poplar.h
> new file mode 100644
> index 0000000..55e05d6
> --- /dev/null
> +++ b/include/configs/poplar.h
> @@ -0,0 +1,86 @@
> +/*
> + * (C) Copyright 2017 Linaro
> + *
> + * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> + *
> + * Configuration for Poplar 96boards CE. Parts were derived from other ARM
> + * configurations.
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#ifndef _POPLAR_H_
> +#define _POPLAR_H_
> +
> +#include <linux/sizes.h>
> +
> +/* DRAM banks */
> +#define CONFIG_NR_DRAM_BANKS			2
> +
> +/* SYS */
> +#define CONFIG_SYS_BOOTM_LEN			0x1400000
> +#define CONFIG_SYS_INIT_SP_ADDR			0x200000
> +#define CONFIG_SYS_LOAD_ADDR			0x800000
> +#define CONFIG_SYS_MALLOC_LEN			SZ_32M
> +
> +/* ATF bl33.bin load address (must match) */
> +#define CONFIG_SYS_TEXT_BASE			0x37000000
> +
> +/* PL010/PL011 */
> +#define CONFIG_PL01X_SERIAL
> +
> +/* USB configuration */
> +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
> +#define CONFIG_USB_MAX_CONTROLLER_COUNT		2
> +#define CONFIG_SYS_USB_EVENT_POLL
> +#define CONFIG_USB_HOST_ETHER
> +#define CONFIG_USB_ETHER_ASIX
> +
> +/* SD/MMC */
> +#define CONFIG_BOUNCE_BUFFER
> +
> +/*****************************************************************************
> + *  Initial environment variables
> + *****************************************************************************/
> +
> +#define BOOT_TARGET_DEVICES(func)					\
> +					func(USB, usb, 0)		\
> +					func(MMC, mmc, 0)		\
> +					func(DHCP, dhcp, na)
> +#ifndef CONFIG_SPL_BUILD
> +#include <config_distro_defaults.h>
> +#include <config_distro_bootcmd.h>
> +#endif
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS					\
> +			"loader_mmc_blknum=0x0\0"			\
> +			"loader_mmc_nblks=0x780\0"			\
> +			"env_mmc_blknum=0x780\0"			\
> +			"env_mmc_nblks=0x80\0"				\
> +			"kernel_addr_r=0x30000000\0"			\
> +			"pxefile_addr_r=0x32000000\0"			\
> +			"scriptaddr=0x32000000\0"			\
> +			"fdt_addr_r=0x32200000\0"			\
> +			"fdtfile=hisilicon/hi3798cv200-poplar.dtb\0"	\
> +			"ramdisk_addr_r=0x32400000\0"			\
> +			BOOTENV
> +
> +
> +/* Command line configuration */
> +#define CONFIG_ENV_IS_IN_MMC		1
> +#define CONFIG_SYS_MMC_ENV_DEV		0
> +#define CONFIG_ENV_OFFSET		(0x780 * 512)	/* env_mmc_blknum */
> +#define CONFIG_ENV_SIZE			0x10000	/* env_mmc_nblks bytes */
> +#define CONFIG_FAT_WRITE
> +#define CONFIG_ENV_VARS_UBOOT_CONFIG
> +
> +/* Monitor Command Prompt */
> +#define CONFIG_CMDLINE_EDITING
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_SYS_CBSIZE		512
> +#define CONFIG_SYS_MAXARGS		64
> +#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
> +					sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
> +
> +#endif /* _POPLAR_H_ */

[U-Boot] [PATCHv6 3/3] ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards

[Jorge Ramirez]

On 06/28/2017 11:44 AM, Jorge Ramirez wrote:
> On 06/26/2017 03:52 PM, Jorge Ramirez-Ortiz wrote:
>> This port adds support for:
>>          1) Serial
>>          2) eMMC
>>          3) USB
>>
>> It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
>> BL33 executable [see board's README]
>
>
> FYI, I just submitted the Pull Request to the arm trusted firmware 
> project:
> https://github.com/ARM-software/arm-trusted-firmware/pull/1005/commits/420eabe76eb0a23314b21044f4387464df79d38f


any feedback on v6 of the u-boot Poplar support please?

[U-Boot] [PATCHv6 3/3] ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards

[Tom Rini]

On Mon, Jul 03, 2017 at 09:49:56AM +0200, Jorge Ramirez wrote:
> On 06/28/2017 11:44 AM, Jorge Ramirez wrote:
> >On 06/26/2017 03:52 PM, Jorge Ramirez-Ortiz wrote:
> >>This port adds support for:
> >>         1) Serial
> >>         2) eMMC
> >>         3) USB
> >>
> >>It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
> >>BL33 executable [see board's README]
> >
> >
> >FYI, I just submitted the Pull Request to the arm trusted firmware
> >project:
> >https://github.com/ARM-software/arm-trusted-firmware/pull/1005/commits/420eabe76eb0a23314b21044f4387464df79d38f
> 
> 
> any feedback on v6 of the u-boot Poplar support please?

No, I guess things are in a good enough state for the next release,
thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170704/9196b1f3/attachment.sig>

[U-Boot] [PATCHv6 3/3] ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards

[Jorge Ramirez]

On 07/04/2017 03:29 PM, Tom Rini wrote:
> On Mon, Jul 03, 2017 at 09:49:56AM +0200, Jorge Ramirez wrote:
>> On 06/28/2017 11:44 AM, Jorge Ramirez wrote:
>>> On 06/26/2017 03:52 PM, Jorge Ramirez-Ortiz wrote:
>>>> This port adds support for:
>>>>          1) Serial
>>>>          2) eMMC
>>>>          3) USB
>>>>
>>>> It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
>>>> BL33 executable [see board's README]
>>>
>>> FYI, I just submitted the Pull Request to the arm trusted firmware
>>> project:
>>> https://github.com/ARM-software/arm-trusted-firmware/pull/1005/commits/420eabe76eb0a23314b21044f4387464df79d38f
>>
>> any feedback on v6 of the u-boot Poplar support please?
> No, I guess things are in a good enough state for the next release,
> thanks!
>

awesome. thanks for all the reviews.

[U-Boot] [PATCHv6 1/3] ARM64: dts: hi3798cv200-poplar: add device tree bindings

[Simon Glass]

On 26 June 2017 at 07:52, Jorge Ramirez-Ortiz
<jorge.ramirez-ortiz@linaro.org> wrote:
> Pulled from Linux 4.12-rc3
>
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> ---
>  arch/arm/dts/hi3798cv200-poplar.dts     | 162 +++++++++++++
>  arch/arm/dts/hi3798cv200.dtsi           | 411 ++++++++++++++++++++++++++++++++
>  include/dt-bindings/clock/histb-clock.h |  66 +++++
>  include/dt-bindings/reset/ti-syscon.h   |  38 +++
>  4 files changed, 677 insertions(+)
>  create mode 100644 arch/arm/dts/hi3798cv200-poplar.dts
>  create mode 100644 arch/arm/dts/hi3798cv200.dtsi
>  create mode 100644 include/dt-bindings/clock/histb-clock.h
>  create mode 100644 include/dt-bindings/reset/ti-syscon.h

Reviewed-by: Simon Glass <sjg@chromium.org>

[U-Boot] [PATCHv6 2/3] driver: mmc: update debug info

[Simon Glass]

On 26 June 2017 at 07:52, Jorge Ramirez-Ortiz
<jorge.ramirez-ortiz@linaro.org> wrote:
> This driver is used in another board; remove board information from
> the driver debug log.
>
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> ---
>  drivers/mmc/hi6220_dw_mmc.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)

Reviewed-by: Simon Glass <sjg@chromium.org>

[U-Boot] [U-Boot, PATCHv6, 1/3] ARM64: dts: hi3798cv200-poplar: add device tree bindings

[Tom Rini]

On Mon, Jun 26, 2017 at 03:52:47PM +0200, Jorge Ramirez-Ortiz wrote:

> Pulled from Linux 4.12-rc3
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> Reviewed-by: Simon Glass <sjg@chromium.org>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170711/105fdd37/attachment.sig>

[U-Boot] [U-Boot,PATCHv6,2/3] driver: mmc: update debug info

[Tom Rini]

On Mon, Jun 26, 2017 at 03:52:48PM +0200, Jorge Ramirez-Ortiz wrote:

> This driver is used in another board; remove board information from
> the driver debug log.
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> Reviewed-by: Simon Glass <sjg@chromium.org>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170711/7c7613d5/attachment.sig>

[U-Boot] [U-Boot, PATCHv6, 3/3] ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards

[Tom Rini]

On Mon, Jun 26, 2017 at 03:52:49PM +0200, Jorge Ramirez-Ortiz wrote:

> This port adds support for:
>         1) Serial
>         2) eMMC
>         3) USB
> 
> It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
> BL33 executable [see board's README]
> 
> eMMC has been tested for reading and booting the loader and linux
> kernels as well as saving the u-boot environment.
> 
> USB has been tested with ASIX networking adapter and SanDisk 7.4GB
> drive.
> 
> PSCI has been tested via the reset call (PSCI executes from DDR)
> 
> The firwmare upgrade process has been tested via TFTP and USB FAT
> filesystem containing the fastboot.bin image in one of the partitions.
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170711/50de403a/attachment.sig>