* [PATCH 1/3] rk3399: orangepi: Enable TPL
@ 2019-05-09 10:57 ` Jagan Teki
0 siblings, 0 replies; 20+ messages in thread
From: Jagan Teki @ 2019-05-09 10:57 UTC (permalink / raw)
To: Kever Yang, Simon Glass, Philipp Tomsich
Cc: linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-amarula-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/,
Jagan Teki, u-boot-0aAXYlwwYIKGBzrmiIFOJg
Enable TPL for OrangePI rk3399 board.
Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
---
configs/orangepi-rk3399_defconfig | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig
index 3f02c89983..90021bb695 100644
--- a/configs/orangepi-rk3399_defconfig
+++ b/configs/orangepi-rk3399_defconfig
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
CONFIG_DEBUG_UART_BASE=0xFF1A0000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SPL_STACK_R_ADDR=0x80000
@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPT=y
CONFIG_CMD_MMC=y
@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_TIME=y
+CONFIG_TPL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
CONFIG_USB_ETHER_RTL8152=y
CONFIG_USB_ETHER_SMSC95XX=y
CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
CONFIG_ERRNO_STR=y
--
2.18.0.321.gffc6fa0e3
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 1/3] rk3399: orangepi: Enable TPL
@ 2019-05-09 10:57 ` Jagan Teki
0 siblings, 0 replies; 20+ messages in thread
From: Jagan Teki @ 2019-05-09 10:57 UTC (permalink / raw)
To: u-boot
Enable TPL for OrangePI rk3399 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
configs/orangepi-rk3399_defconfig | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig
index 3f02c89983..90021bb695 100644
--- a/configs/orangepi-rk3399_defconfig
+++ b/configs/orangepi-rk3399_defconfig
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
CONFIG_DEBUG_UART_BASE=0xFF1A0000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SPL_STACK_R_ADDR=0x80000
@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPT=y
CONFIG_CMD_MMC=y
@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_TIME=y
+CONFIG_TPL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
CONFIG_USB_ETHER_RTL8152=y
CONFIG_USB_ETHER_SMSC95XX=y
CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
CONFIG_ERRNO_STR=y
--
2.18.0.321.gffc6fa0e3
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 2/3] rk3399: nanopi4: Enable TPL
2019-05-09 10:57 ` [U-Boot] " Jagan Teki
@ 2019-05-09 10:57 ` Jagan Teki
-1 siblings, 0 replies; 20+ messages in thread
From: Jagan Teki @ 2019-05-09 10:57 UTC (permalink / raw)
To: Kever Yang, Simon Glass, Philipp Tomsich
Cc: linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-amarula-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/,
Jagan Teki, u-boot-0aAXYlwwYIKGBzrmiIFOJg
Enable TPL for NanoPC T4, NanoPI M4 boards.
Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
---
configs/nanopc-t4-rk3399_defconfig | 7 ++++---
configs/nanopi-m4-rk3399_defconfig | 7 ++++---
2 files changed, 8 insertions(+), 6 deletions(-)
diff --git a/configs/nanopc-t4-rk3399_defconfig b/configs/nanopc-t4-rk3399_defconfig
index d9f2137b4c..9b7e15d63a 100644
--- a/configs/nanopc-t4-rk3399_defconfig
+++ b/configs/nanopc-t4-rk3399_defconfig
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
CONFIG_DEBUG_UART_BASE=0xFF1A0000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SPL_STACK_R_ADDR=0x80000
@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPT=y
CONFIG_CMD_MMC=y
@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_TIME=y
+CONFIG_TPL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4"
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
CONFIG_USB_ETHER_RTL8152=y
CONFIG_USB_ETHER_SMSC95XX=y
CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
CONFIG_ERRNO_STR=y
diff --git a/configs/nanopi-m4-rk3399_defconfig b/configs/nanopi-m4-rk3399_defconfig
index c2832788f0..92e70dd939 100644
--- a/configs/nanopi-m4-rk3399_defconfig
+++ b/configs/nanopi-m4-rk3399_defconfig
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
CONFIG_DEBUG_UART_BASE=0xFF1A0000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SPL_STACK_R_ADDR=0x80000
@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPT=y
CONFIG_CMD_MMC=y
@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_TIME=y
+CONFIG_TPL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4"
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
CONFIG_USB_ETHER_RTL8152=y
CONFIG_USB_ETHER_SMSC95XX=y
CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
CONFIG_ERRNO_STR=y
--
2.18.0.321.gffc6fa0e3
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 2/3] rk3399: nanopi4: Enable TPL
@ 2019-05-09 10:57 ` Jagan Teki
0 siblings, 0 replies; 20+ messages in thread
From: Jagan Teki @ 2019-05-09 10:57 UTC (permalink / raw)
To: u-boot
Enable TPL for NanoPC T4, NanoPI M4 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
configs/nanopc-t4-rk3399_defconfig | 7 ++++---
configs/nanopi-m4-rk3399_defconfig | 7 ++++---
2 files changed, 8 insertions(+), 6 deletions(-)
diff --git a/configs/nanopc-t4-rk3399_defconfig b/configs/nanopc-t4-rk3399_defconfig
index d9f2137b4c..9b7e15d63a 100644
--- a/configs/nanopc-t4-rk3399_defconfig
+++ b/configs/nanopc-t4-rk3399_defconfig
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
CONFIG_DEBUG_UART_BASE=0xFF1A0000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SPL_STACK_R_ADDR=0x80000
@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPT=y
CONFIG_CMD_MMC=y
@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_TIME=y
+CONFIG_TPL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4"
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
CONFIG_USB_ETHER_RTL8152=y
CONFIG_USB_ETHER_SMSC95XX=y
CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
CONFIG_ERRNO_STR=y
diff --git a/configs/nanopi-m4-rk3399_defconfig b/configs/nanopi-m4-rk3399_defconfig
index c2832788f0..92e70dd939 100644
--- a/configs/nanopi-m4-rk3399_defconfig
+++ b/configs/nanopi-m4-rk3399_defconfig
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
CONFIG_DEBUG_UART_BASE=0xFF1A0000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SPL_STACK_R_ADDR=0x80000
@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPT=y
CONFIG_CMD_MMC=y
@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_TIME=y
+CONFIG_TPL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4"
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
CONFIG_USB_ETHER_RTL8152=y
CONFIG_USB_ETHER_SMSC95XX=y
CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
CONFIG_ERRNO_STR=y
--
2.18.0.321.gffc6fa0e3
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 3/3] doc: rockchip: Add doc for rk3399 TPL build/flash
2019-05-09 10:57 ` [U-Boot] " Jagan Teki
@ 2019-05-09 10:57 ` Jagan Teki
-1 siblings, 0 replies; 20+ messages in thread
From: Jagan Teki @ 2019-05-09 10:57 UTC (permalink / raw)
To: Kever Yang, Simon Glass, Philipp Tomsich
Cc: linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-amarula-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/,
Jagan Teki, u-boot-0aAXYlwwYIKGBzrmiIFOJg
This patch add documentation for TPL build and flashing steps
for rk3399 boards.
Add full boot log for future reference.
Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
---
doc/README.rockchip | 51 ++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 50 insertions(+), 1 deletion(-)
diff --git a/doc/README.rockchip b/doc/README.rockchip
index ca4d6473b0..264f7e4994 100644
--- a/doc/README.rockchip
+++ b/doc/README.rockchip
@@ -173,7 +173,10 @@ For example:
=> make u-boot.itb
(Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
- spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL)
+ spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
+
+ If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
+ if CONFIG_TPL_OF_CONTROL not enabled)
Writing to the board with USB
=============================
@@ -455,6 +458,52 @@ Net: eth0: ethernet@fe300000
Hit any key to stop autoboot: 0
=>
+Option 3: Package the image with TPL:
+
+ - Prefix rk3399 header to TPL image
+
+ => cd /path/to/u-boot
+ => ./tools/mkimage -n rk3399 -T rksd -d tpl/u-boot-tpl-dtb.bin out
+
+ - Concatinate tpl with spl
+
+ => cd /path/to/u-boot
+ => cat ./spl/u-boot-spl-dtb.bin >> out
+
+ - Write tpl+spl at 64th sector
+
+ => sudo dd if=out of=/dev/sdc seek=64
+
+ - Write U-Boot proper at 16384 sector
+
+ => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
+ => sync
+
+Put this SD (or micro-SD) card into your board and reset it. You should see
+something like:
+
+U-Boot TPL board init
+Trying to boot from BOOTROM
+Returning to boot ROM...
+
+U-Boot SPL board init
+Trying to boot from MMC1
+
+
+U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
+
+Model: Orange Pi RK3399 Board
+DRAM: 2 GiB
+MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0
+Loading Environment from MMC... OK
+In: serial@ff1a0000
+Out: serial@ff1a0000
+Err: serial@ff1a0000
+Model: Orange Pi RK3399 Board
+Net: eth0: ethernet@fe300000
+Hit any key to stop autoboot: 0
+=>
+
Using fastboot on rk3288
========================
- Write GPT partition layout to mmc device which fastboot want to use it to
--
2.18.0.321.gffc6fa0e3
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 3/3] doc: rockchip: Add doc for rk3399 TPL build/flash
@ 2019-05-09 10:57 ` Jagan Teki
0 siblings, 0 replies; 20+ messages in thread
From: Jagan Teki @ 2019-05-09 10:57 UTC (permalink / raw)
To: u-boot
This patch add documentation for TPL build and flashing steps
for rk3399 boards.
Add full boot log for future reference.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
doc/README.rockchip | 51 ++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 50 insertions(+), 1 deletion(-)
diff --git a/doc/README.rockchip b/doc/README.rockchip
index ca4d6473b0..264f7e4994 100644
--- a/doc/README.rockchip
+++ b/doc/README.rockchip
@@ -173,7 +173,10 @@ For example:
=> make u-boot.itb
(Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
- spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL)
+ spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
+
+ If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
+ if CONFIG_TPL_OF_CONTROL not enabled)
Writing to the board with USB
=============================
@@ -455,6 +458,52 @@ Net: eth0: ethernet at fe300000
Hit any key to stop autoboot: 0
=>
+Option 3: Package the image with TPL:
+
+ - Prefix rk3399 header to TPL image
+
+ => cd /path/to/u-boot
+ => ./tools/mkimage -n rk3399 -T rksd -d tpl/u-boot-tpl-dtb.bin out
+
+ - Concatinate tpl with spl
+
+ => cd /path/to/u-boot
+ => cat ./spl/u-boot-spl-dtb.bin >> out
+
+ - Write tpl+spl at 64th sector
+
+ => sudo dd if=out of=/dev/sdc seek=64
+
+ - Write U-Boot proper at 16384 sector
+
+ => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
+ => sync
+
+Put this SD (or micro-SD) card into your board and reset it. You should see
+something like:
+
+U-Boot TPL board init
+Trying to boot from BOOTROM
+Returning to boot ROM...
+
+U-Boot SPL board init
+Trying to boot from MMC1
+
+
+U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
+
+Model: Orange Pi RK3399 Board
+DRAM: 2 GiB
+MMC: dwmmc at fe310000: 2, dwmmc at fe320000: 1, sdhci at fe330000: 0
+Loading Environment from MMC... OK
+In: serial at ff1a0000
+Out: serial at ff1a0000
+Err: serial at ff1a0000
+Model: Orange Pi RK3399 Board
+Net: eth0: ethernet at fe300000
+Hit any key to stop autoboot: 0
+=>
+
Using fastboot on rk3288
========================
- Write GPT partition layout to mmc device which fastboot want to use it to
--
2.18.0.321.gffc6fa0e3
^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH 1/3] rk3399: orangepi: Enable TPL
2019-05-09 10:57 ` [U-Boot] " Jagan Teki
@ 2019-05-29 8:01 ` Kever Yang
-1 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-05-29 8:01 UTC (permalink / raw)
To: Jagan Teki, Simon Glass, Philipp Tomsich
Cc: linux-rockchip, linux-amarula, u-boot
Hi Jagan,
On 05/09/2019 06:57 PM, Jagan Teki wrote:
> Enable TPL for OrangePI rk3399 board.
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Thanks,
- Kever
> ---
> configs/orangepi-rk3399_defconfig | 7 ++++---
> 1 file changed, 4 insertions(+), 3 deletions(-)
>
> diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig
> index 3f02c89983..90021bb695 100644
> --- a/configs/orangepi-rk3399_defconfig
> +++ b/configs/orangepi-rk3399_defconfig
> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
> CONFIG_SPL_LIBGENERIC_SUPPORT=y
> CONFIG_SYS_MALLOC_F_LEN=0x4000
> CONFIG_ROCKCHIP_RK3399=y
> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
> CONFIG_DEBUG_UART_BASE=0xFF1A0000
> CONFIG_DEBUG_UART_CLOCK=24000000
> CONFIG_SPL_STACK_R_ADDR=0x80000
> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
> # CONFIG_DISPLAY_CPUINFO is not set
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> -CONFIG_SPL_TEXT_BASE=0xff8c2000
> CONFIG_SPL_STACK_R=y
> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> CONFIG_CMD_BOOTZ=y
> CONFIG_CMD_GPT=y
> CONFIG_CMD_MMC=y
> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_TIME=y
> +CONFIG_TPL=y
> CONFIG_SPL_OF_CONTROL=y
> CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
> CONFIG_USB_ETHER_RTL8152=y
> CONFIG_USB_ETHER_SMSC95XX=y
> CONFIG_USE_TINY_PRINTF=y
> +CONFIG_SPL_TINY_MEMSET=y
> CONFIG_ERRNO_STR=y
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 1/3] rk3399: orangepi: Enable TPL
@ 2019-05-29 8:01 ` Kever Yang
0 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-05-29 8:01 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 05/09/2019 06:57 PM, Jagan Teki wrote:
> Enable TPL for OrangePI rk3399 board.
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Thanks,
- Kever
> ---
> configs/orangepi-rk3399_defconfig | 7 ++++---
> 1 file changed, 4 insertions(+), 3 deletions(-)
>
> diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig
> index 3f02c89983..90021bb695 100644
> --- a/configs/orangepi-rk3399_defconfig
> +++ b/configs/orangepi-rk3399_defconfig
> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
> CONFIG_SPL_LIBGENERIC_SUPPORT=y
> CONFIG_SYS_MALLOC_F_LEN=0x4000
> CONFIG_ROCKCHIP_RK3399=y
> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
> CONFIG_DEBUG_UART_BASE=0xFF1A0000
> CONFIG_DEBUG_UART_CLOCK=24000000
> CONFIG_SPL_STACK_R_ADDR=0x80000
> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
> # CONFIG_DISPLAY_CPUINFO is not set
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> -CONFIG_SPL_TEXT_BASE=0xff8c2000
> CONFIG_SPL_STACK_R=y
> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> CONFIG_CMD_BOOTZ=y
> CONFIG_CMD_GPT=y
> CONFIG_CMD_MMC=y
> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_TIME=y
> +CONFIG_TPL=y
> CONFIG_SPL_OF_CONTROL=y
> CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
> CONFIG_USB_ETHER_RTL8152=y
> CONFIG_USB_ETHER_SMSC95XX=y
> CONFIG_USE_TINY_PRINTF=y
> +CONFIG_SPL_TINY_MEMSET=y
> CONFIG_ERRNO_STR=y
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 2/3] rk3399: nanopi4: Enable TPL
2019-05-09 10:57 ` [U-Boot] " Jagan Teki
@ 2019-05-29 8:02 ` Kever Yang
-1 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-05-29 8:02 UTC (permalink / raw)
To: Jagan Teki, Simon Glass, Philipp Tomsich
Cc: linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-amarula-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/,
u-boot-0aAXYlwwYIKGBzrmiIFOJg
Hi Jagan,
On 05/09/2019 06:57 PM, Jagan Teki wrote:
> Enable TPL for NanoPC T4, NanoPI M4 boards.
>
> Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Reviewed-by: Kever Yang <kever.yang-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Thanks,
- Kever
> ---
> configs/nanopc-t4-rk3399_defconfig | 7 ++++---
> configs/nanopi-m4-rk3399_defconfig | 7 ++++---
> 2 files changed, 8 insertions(+), 6 deletions(-)
>
> diff --git a/configs/nanopc-t4-rk3399_defconfig b/configs/nanopc-t4-rk3399_defconfig
> index d9f2137b4c..9b7e15d63a 100644
> --- a/configs/nanopc-t4-rk3399_defconfig
> +++ b/configs/nanopc-t4-rk3399_defconfig
> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
> CONFIG_SPL_LIBGENERIC_SUPPORT=y
> CONFIG_SYS_MALLOC_F_LEN=0x4000
> CONFIG_ROCKCHIP_RK3399=y
> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
> CONFIG_DEBUG_UART_BASE=0xFF1A0000
> CONFIG_DEBUG_UART_CLOCK=24000000
> CONFIG_SPL_STACK_R_ADDR=0x80000
> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb"
> # CONFIG_DISPLAY_CPUINFO is not set
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> -CONFIG_SPL_TEXT_BASE=0xff8c2000
> CONFIG_SPL_STACK_R=y
> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> CONFIG_CMD_BOOTZ=y
> CONFIG_CMD_GPT=y
> CONFIG_CMD_MMC=y
> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_TIME=y
> +CONFIG_TPL=y
> CONFIG_SPL_OF_CONTROL=y
> CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4"
> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
> CONFIG_USB_ETHER_RTL8152=y
> CONFIG_USB_ETHER_SMSC95XX=y
> CONFIG_USE_TINY_PRINTF=y
> +CONFIG_SPL_TINY_MEMSET=y
> CONFIG_ERRNO_STR=y
> diff --git a/configs/nanopi-m4-rk3399_defconfig b/configs/nanopi-m4-rk3399_defconfig
> index c2832788f0..92e70dd939 100644
> --- a/configs/nanopi-m4-rk3399_defconfig
> +++ b/configs/nanopi-m4-rk3399_defconfig
> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
> CONFIG_SPL_LIBGENERIC_SUPPORT=y
> CONFIG_SYS_MALLOC_F_LEN=0x4000
> CONFIG_ROCKCHIP_RK3399=y
> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
> CONFIG_DEBUG_UART_BASE=0xFF1A0000
> CONFIG_DEBUG_UART_CLOCK=24000000
> CONFIG_SPL_STACK_R_ADDR=0x80000
> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb"
> # CONFIG_DISPLAY_CPUINFO is not set
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> -CONFIG_SPL_TEXT_BASE=0xff8c2000
> CONFIG_SPL_STACK_R=y
> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> CONFIG_CMD_BOOTZ=y
> CONFIG_CMD_GPT=y
> CONFIG_CMD_MMC=y
> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_TIME=y
> +CONFIG_TPL=y
> CONFIG_SPL_OF_CONTROL=y
> CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4"
> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
> CONFIG_USB_ETHER_RTL8152=y
> CONFIG_USB_ETHER_SMSC95XX=y
> CONFIG_USE_TINY_PRINTF=y
> +CONFIG_SPL_TINY_MEMSET=y
> CONFIG_ERRNO_STR=y
^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 2/3] rk3399: nanopi4: Enable TPL
@ 2019-05-29 8:02 ` Kever Yang
0 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-05-29 8:02 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 05/09/2019 06:57 PM, Jagan Teki wrote:
> Enable TPL for NanoPC T4, NanoPI M4 boards.
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Thanks,
- Kever
> ---
> configs/nanopc-t4-rk3399_defconfig | 7 ++++---
> configs/nanopi-m4-rk3399_defconfig | 7 ++++---
> 2 files changed, 8 insertions(+), 6 deletions(-)
>
> diff --git a/configs/nanopc-t4-rk3399_defconfig b/configs/nanopc-t4-rk3399_defconfig
> index d9f2137b4c..9b7e15d63a 100644
> --- a/configs/nanopc-t4-rk3399_defconfig
> +++ b/configs/nanopc-t4-rk3399_defconfig
> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
> CONFIG_SPL_LIBGENERIC_SUPPORT=y
> CONFIG_SYS_MALLOC_F_LEN=0x4000
> CONFIG_ROCKCHIP_RK3399=y
> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
> CONFIG_DEBUG_UART_BASE=0xFF1A0000
> CONFIG_DEBUG_UART_CLOCK=24000000
> CONFIG_SPL_STACK_R_ADDR=0x80000
> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb"
> # CONFIG_DISPLAY_CPUINFO is not set
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> -CONFIG_SPL_TEXT_BASE=0xff8c2000
> CONFIG_SPL_STACK_R=y
> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> CONFIG_CMD_BOOTZ=y
> CONFIG_CMD_GPT=y
> CONFIG_CMD_MMC=y
> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_TIME=y
> +CONFIG_TPL=y
> CONFIG_SPL_OF_CONTROL=y
> CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4"
> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
> CONFIG_USB_ETHER_RTL8152=y
> CONFIG_USB_ETHER_SMSC95XX=y
> CONFIG_USE_TINY_PRINTF=y
> +CONFIG_SPL_TINY_MEMSET=y
> CONFIG_ERRNO_STR=y
> diff --git a/configs/nanopi-m4-rk3399_defconfig b/configs/nanopi-m4-rk3399_defconfig
> index c2832788f0..92e70dd939 100644
> --- a/configs/nanopi-m4-rk3399_defconfig
> +++ b/configs/nanopi-m4-rk3399_defconfig
> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
> CONFIG_SPL_LIBGENERIC_SUPPORT=y
> CONFIG_SYS_MALLOC_F_LEN=0x4000
> CONFIG_ROCKCHIP_RK3399=y
> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
> CONFIG_DEBUG_UART_BASE=0xFF1A0000
> CONFIG_DEBUG_UART_CLOCK=24000000
> CONFIG_SPL_STACK_R_ADDR=0x80000
> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb"
> # CONFIG_DISPLAY_CPUINFO is not set
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> -CONFIG_SPL_TEXT_BASE=0xff8c2000
> CONFIG_SPL_STACK_R=y
> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> CONFIG_CMD_BOOTZ=y
> CONFIG_CMD_GPT=y
> CONFIG_CMD_MMC=y
> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_TIME=y
> +CONFIG_TPL=y
> CONFIG_SPL_OF_CONTROL=y
> CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4"
> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
> CONFIG_USB_ETHER_RTL8152=y
> CONFIG_USB_ETHER_SMSC95XX=y
> CONFIG_USE_TINY_PRINTF=y
> +CONFIG_SPL_TINY_MEMSET=y
> CONFIG_ERRNO_STR=y
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 3/3] doc: rockchip: Add doc for rk3399 TPL build/flash
2019-05-09 10:57 ` [U-Boot] " Jagan Teki
@ 2019-05-29 8:02 ` Kever Yang
-1 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-05-29 8:02 UTC (permalink / raw)
To: Jagan Teki, Simon Glass, Philipp Tomsich
Cc: linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-amarula-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/,
u-boot-0aAXYlwwYIKGBzrmiIFOJg
Hi Jagan,
On 05/09/2019 06:57 PM, Jagan Teki wrote:
> This patch add documentation for TPL build and flashing steps
> for rk3399 boards.
>
> Add full boot log for future reference.
>
> Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Reviewed-by: Kever Yang <kever.yang-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Thanks,
- Kever
> ---
> doc/README.rockchip | 51 ++++++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 50 insertions(+), 1 deletion(-)
>
> diff --git a/doc/README.rockchip b/doc/README.rockchip
> index ca4d6473b0..264f7e4994 100644
> --- a/doc/README.rockchip
> +++ b/doc/README.rockchip
> @@ -173,7 +173,10 @@ For example:
> => make u-boot.itb
>
> (Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
> - spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL)
> + spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
> +
> + If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
> + if CONFIG_TPL_OF_CONTROL not enabled)
>
> Writing to the board with USB
> =============================
> @@ -455,6 +458,52 @@ Net: eth0: ethernet@fe300000
> Hit any key to stop autoboot: 0
> =>
>
> +Option 3: Package the image with TPL:
> +
> + - Prefix rk3399 header to TPL image
> +
> + => cd /path/to/u-boot
> + => ./tools/mkimage -n rk3399 -T rksd -d tpl/u-boot-tpl-dtb.bin out
> +
> + - Concatinate tpl with spl
> +
> + => cd /path/to/u-boot
> + => cat ./spl/u-boot-spl-dtb.bin >> out
> +
> + - Write tpl+spl at 64th sector
> +
> + => sudo dd if=out of=/dev/sdc seek=64
> +
> + - Write U-Boot proper at 16384 sector
> +
> + => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
> + => sync
> +
> +Put this SD (or micro-SD) card into your board and reset it. You should see
> +something like:
> +
> +U-Boot TPL board init
> +Trying to boot from BOOTROM
> +Returning to boot ROM...
> +
> +U-Boot SPL board init
> +Trying to boot from MMC1
> +
> +
> +U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
> +
> +Model: Orange Pi RK3399 Board
> +DRAM: 2 GiB
> +MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0
> +Loading Environment from MMC... OK
> +In: serial@ff1a0000
> +Out: serial@ff1a0000
> +Err: serial@ff1a0000
> +Model: Orange Pi RK3399 Board
> +Net: eth0: ethernet@fe300000
> +Hit any key to stop autoboot: 0
> +=>
> +
> Using fastboot on rk3288
> ========================
> - Write GPT partition layout to mmc device which fastboot want to use it to
^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 3/3] doc: rockchip: Add doc for rk3399 TPL build/flash
@ 2019-05-29 8:02 ` Kever Yang
0 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-05-29 8:02 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 05/09/2019 06:57 PM, Jagan Teki wrote:
> This patch add documentation for TPL build and flashing steps
> for rk3399 boards.
>
> Add full boot log for future reference.
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Thanks,
- Kever
> ---
> doc/README.rockchip | 51 ++++++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 50 insertions(+), 1 deletion(-)
>
> diff --git a/doc/README.rockchip b/doc/README.rockchip
> index ca4d6473b0..264f7e4994 100644
> --- a/doc/README.rockchip
> +++ b/doc/README.rockchip
> @@ -173,7 +173,10 @@ For example:
> => make u-boot.itb
>
> (Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
> - spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL)
> + spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
> +
> + If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
> + if CONFIG_TPL_OF_CONTROL not enabled)
>
> Writing to the board with USB
> =============================
> @@ -455,6 +458,52 @@ Net: eth0: ethernet at fe300000
> Hit any key to stop autoboot: 0
> =>
>
> +Option 3: Package the image with TPL:
> +
> + - Prefix rk3399 header to TPL image
> +
> + => cd /path/to/u-boot
> + => ./tools/mkimage -n rk3399 -T rksd -d tpl/u-boot-tpl-dtb.bin out
> +
> + - Concatinate tpl with spl
> +
> + => cd /path/to/u-boot
> + => cat ./spl/u-boot-spl-dtb.bin >> out
> +
> + - Write tpl+spl at 64th sector
> +
> + => sudo dd if=out of=/dev/sdc seek=64
> +
> + - Write U-Boot proper at 16384 sector
> +
> + => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
> + => sync
> +
> +Put this SD (or micro-SD) card into your board and reset it. You should see
> +something like:
> +
> +U-Boot TPL board init
> +Trying to boot from BOOTROM
> +Returning to boot ROM...
> +
> +U-Boot SPL board init
> +Trying to boot from MMC1
> +
> +
> +U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
> +
> +Model: Orange Pi RK3399 Board
> +DRAM: 2 GiB
> +MMC: dwmmc at fe310000: 2, dwmmc at fe320000: 1, sdhci at fe330000: 0
> +Loading Environment from MMC... OK
> +In: serial at ff1a0000
> +Out: serial at ff1a0000
> +Err: serial at ff1a0000
> +Model: Orange Pi RK3399 Board
> +Net: eth0: ethernet at fe300000
> +Hit any key to stop autoboot: 0
> +=>
> +
> Using fastboot on rk3288
> ========================
> - Write GPT partition layout to mmc device which fastboot want to use it to
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 1/3] rk3399: orangepi: Enable TPL
2019-05-09 10:57 ` [U-Boot] " Jagan Teki
@ 2019-05-29 8:06 ` Kever Yang
-1 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-05-29 8:06 UTC (permalink / raw)
To: Jagan Teki, Simon Glass, Philipp Tomsich
Cc: linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-amarula-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/,
u-boot-0aAXYlwwYIKGBzrmiIFOJg
Hi Jagan,
The first two patches need re-base after the patch from Tom:
344a0e4367 configs: Resync with savedefconfig
Thanks,
- Kever
On 05/09/2019 06:57 PM, Jagan Teki wrote:
> Enable TPL for OrangePI rk3399 board.
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> configs/orangepi-rk3399_defconfig | 7 ++++---
> 1 file changed, 4 insertions(+), 3 deletions(-)
>
> diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig
> index 3f02c89983..90021bb695 100644
> --- a/configs/orangepi-rk3399_defconfig
> +++ b/configs/orangepi-rk3399_defconfig
> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
> CONFIG_SPL_LIBGENERIC_SUPPORT=y
> CONFIG_SYS_MALLOC_F_LEN=0x4000
> CONFIG_ROCKCHIP_RK3399=y
> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
> CONFIG_DEBUG_UART_BASE=0xFF1A0000
> CONFIG_DEBUG_UART_CLOCK=24000000
> CONFIG_SPL_STACK_R_ADDR=0x80000
> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
> # CONFIG_DISPLAY_CPUINFO is not set
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> -CONFIG_SPL_TEXT_BASE=0xff8c2000
> CONFIG_SPL_STACK_R=y
> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> CONFIG_CMD_BOOTZ=y
> CONFIG_CMD_GPT=y
> CONFIG_CMD_MMC=y
> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_TIME=y
> +CONFIG_TPL=y
> CONFIG_SPL_OF_CONTROL=y
> CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
> CONFIG_USB_ETHER_RTL8152=y
> CONFIG_USB_ETHER_SMSC95XX=y
> CONFIG_USE_TINY_PRINTF=y
> +CONFIG_SPL_TINY_MEMSET=y
> CONFIG_ERRNO_STR=y
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 1/3] rk3399: orangepi: Enable TPL
@ 2019-05-29 8:06 ` Kever Yang
0 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-05-29 8:06 UTC (permalink / raw)
To: u-boot
Hi Jagan,
The first two patches need re-base after the patch from Tom:
344a0e4367 configs: Resync with savedefconfig
Thanks,
- Kever
On 05/09/2019 06:57 PM, Jagan Teki wrote:
> Enable TPL for OrangePI rk3399 board.
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> configs/orangepi-rk3399_defconfig | 7 ++++---
> 1 file changed, 4 insertions(+), 3 deletions(-)
>
> diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig
> index 3f02c89983..90021bb695 100644
> --- a/configs/orangepi-rk3399_defconfig
> +++ b/configs/orangepi-rk3399_defconfig
> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
> CONFIG_SPL_LIBGENERIC_SUPPORT=y
> CONFIG_SYS_MALLOC_F_LEN=0x4000
> CONFIG_ROCKCHIP_RK3399=y
> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
> CONFIG_DEBUG_UART_BASE=0xFF1A0000
> CONFIG_DEBUG_UART_CLOCK=24000000
> CONFIG_SPL_STACK_R_ADDR=0x80000
> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
> # CONFIG_DISPLAY_CPUINFO is not set
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> -CONFIG_SPL_TEXT_BASE=0xff8c2000
> CONFIG_SPL_STACK_R=y
> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> CONFIG_CMD_BOOTZ=y
> CONFIG_CMD_GPT=y
> CONFIG_CMD_MMC=y
> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_TIME=y
> +CONFIG_TPL=y
> CONFIG_SPL_OF_CONTROL=y
> CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
> CONFIG_USB_ETHER_RTL8152=y
> CONFIG_USB_ETHER_SMSC95XX=y
> CONFIG_USE_TINY_PRINTF=y
> +CONFIG_SPL_TINY_MEMSET=y
> CONFIG_ERRNO_STR=y
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 2/3] rk3399: nanopi4: Enable TPL
2019-05-29 8:02 ` [U-Boot] " Kever Yang
@ 2019-06-01 2:39 ` Kever Yang
-1 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-06-01 2:39 UTC (permalink / raw)
To: Jagan Teki, Simon Glass, Philipp Tomsich
Cc: linux-rockchip, linux-amarula, u-boot
On 05/29/2019 04:02 PM, Kever Yang wrote:
> Hi Jagan,
>
>
> On 05/09/2019 06:57 PM, Jagan Teki wrote:
>> Enable TPL for NanoPC T4, NanoPI M4 boards.
>>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>
> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Applied to u-boot-rockchip/master, thanks!
>
> Thanks,
> - Kever
>> ---
>> configs/nanopc-t4-rk3399_defconfig | 7 ++++---
>> configs/nanopi-m4-rk3399_defconfig | 7 ++++---
>> 2 files changed, 8 insertions(+), 6 deletions(-)
>>
>> diff --git a/configs/nanopc-t4-rk3399_defconfig b/configs/nanopc-t4-rk3399_defconfig
>> index d9f2137b4c..9b7e15d63a 100644
>> --- a/configs/nanopc-t4-rk3399_defconfig
>> +++ b/configs/nanopc-t4-rk3399_defconfig
>> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
>> CONFIG_SPL_LIBGENERIC_SUPPORT=y
>> CONFIG_SYS_MALLOC_F_LEN=0x4000
>> CONFIG_ROCKCHIP_RK3399=y
>> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
>> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
>> CONFIG_DEBUG_UART_BASE=0xFF1A0000
>> CONFIG_DEBUG_UART_CLOCK=24000000
>> CONFIG_SPL_STACK_R_ADDR=0x80000
>> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
>> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb"
>> # CONFIG_DISPLAY_CPUINFO is not set
>> CONFIG_DISPLAY_BOARDINFO_LATE=y
>> -CONFIG_SPL_TEXT_BASE=0xff8c2000
>> CONFIG_SPL_STACK_R=y
>> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
>> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
>> CONFIG_CMD_BOOTZ=y
>> CONFIG_CMD_GPT=y
>> CONFIG_CMD_MMC=y
>> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
>> CONFIG_CMD_USB=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_CMD_TIME=y
>> +CONFIG_TPL=y
>> CONFIG_SPL_OF_CONTROL=y
>> CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4"
>> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
>> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
>> CONFIG_USB_ETHER_RTL8152=y
>> CONFIG_USB_ETHER_SMSC95XX=y
>> CONFIG_USE_TINY_PRINTF=y
>> +CONFIG_SPL_TINY_MEMSET=y
>> CONFIG_ERRNO_STR=y
>> diff --git a/configs/nanopi-m4-rk3399_defconfig b/configs/nanopi-m4-rk3399_defconfig
>> index c2832788f0..92e70dd939 100644
>> --- a/configs/nanopi-m4-rk3399_defconfig
>> +++ b/configs/nanopi-m4-rk3399_defconfig
>> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
>> CONFIG_SPL_LIBGENERIC_SUPPORT=y
>> CONFIG_SYS_MALLOC_F_LEN=0x4000
>> CONFIG_ROCKCHIP_RK3399=y
>> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
>> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
>> CONFIG_DEBUG_UART_BASE=0xFF1A0000
>> CONFIG_DEBUG_UART_CLOCK=24000000
>> CONFIG_SPL_STACK_R_ADDR=0x80000
>> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
>> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb"
>> # CONFIG_DISPLAY_CPUINFO is not set
>> CONFIG_DISPLAY_BOARDINFO_LATE=y
>> -CONFIG_SPL_TEXT_BASE=0xff8c2000
>> CONFIG_SPL_STACK_R=y
>> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
>> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
>> CONFIG_CMD_BOOTZ=y
>> CONFIG_CMD_GPT=y
>> CONFIG_CMD_MMC=y
>> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
>> CONFIG_CMD_USB=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_CMD_TIME=y
>> +CONFIG_TPL=y
>> CONFIG_SPL_OF_CONTROL=y
>> CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4"
>> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
>> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
>> CONFIG_USB_ETHER_RTL8152=y
>> CONFIG_USB_ETHER_SMSC95XX=y
>> CONFIG_USE_TINY_PRINTF=y
>> +CONFIG_SPL_TINY_MEMSET=y
>> CONFIG_ERRNO_STR=y
>
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 2/3] rk3399: nanopi4: Enable TPL
@ 2019-06-01 2:39 ` Kever Yang
0 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-06-01 2:39 UTC (permalink / raw)
To: u-boot
On 05/29/2019 04:02 PM, Kever Yang wrote:
> Hi Jagan,
>
>
> On 05/09/2019 06:57 PM, Jagan Teki wrote:
>> Enable TPL for NanoPC T4, NanoPI M4 boards.
>>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>
> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Applied to u-boot-rockchip/master, thanks!
>
> Thanks,
> - Kever
>> ---
>> configs/nanopc-t4-rk3399_defconfig | 7 ++++---
>> configs/nanopi-m4-rk3399_defconfig | 7 ++++---
>> 2 files changed, 8 insertions(+), 6 deletions(-)
>>
>> diff --git a/configs/nanopc-t4-rk3399_defconfig b/configs/nanopc-t4-rk3399_defconfig
>> index d9f2137b4c..9b7e15d63a 100644
>> --- a/configs/nanopc-t4-rk3399_defconfig
>> +++ b/configs/nanopc-t4-rk3399_defconfig
>> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
>> CONFIG_SPL_LIBGENERIC_SUPPORT=y
>> CONFIG_SYS_MALLOC_F_LEN=0x4000
>> CONFIG_ROCKCHIP_RK3399=y
>> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
>> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
>> CONFIG_DEBUG_UART_BASE=0xFF1A0000
>> CONFIG_DEBUG_UART_CLOCK=24000000
>> CONFIG_SPL_STACK_R_ADDR=0x80000
>> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
>> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb"
>> # CONFIG_DISPLAY_CPUINFO is not set
>> CONFIG_DISPLAY_BOARDINFO_LATE=y
>> -CONFIG_SPL_TEXT_BASE=0xff8c2000
>> CONFIG_SPL_STACK_R=y
>> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
>> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
>> CONFIG_CMD_BOOTZ=y
>> CONFIG_CMD_GPT=y
>> CONFIG_CMD_MMC=y
>> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
>> CONFIG_CMD_USB=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_CMD_TIME=y
>> +CONFIG_TPL=y
>> CONFIG_SPL_OF_CONTROL=y
>> CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4"
>> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
>> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
>> CONFIG_USB_ETHER_RTL8152=y
>> CONFIG_USB_ETHER_SMSC95XX=y
>> CONFIG_USE_TINY_PRINTF=y
>> +CONFIG_SPL_TINY_MEMSET=y
>> CONFIG_ERRNO_STR=y
>> diff --git a/configs/nanopi-m4-rk3399_defconfig b/configs/nanopi-m4-rk3399_defconfig
>> index c2832788f0..92e70dd939 100644
>> --- a/configs/nanopi-m4-rk3399_defconfig
>> +++ b/configs/nanopi-m4-rk3399_defconfig
>> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
>> CONFIG_SPL_LIBGENERIC_SUPPORT=y
>> CONFIG_SYS_MALLOC_F_LEN=0x4000
>> CONFIG_ROCKCHIP_RK3399=y
>> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
>> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
>> CONFIG_DEBUG_UART_BASE=0xFF1A0000
>> CONFIG_DEBUG_UART_CLOCK=24000000
>> CONFIG_SPL_STACK_R_ADDR=0x80000
>> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
>> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb"
>> # CONFIG_DISPLAY_CPUINFO is not set
>> CONFIG_DISPLAY_BOARDINFO_LATE=y
>> -CONFIG_SPL_TEXT_BASE=0xff8c2000
>> CONFIG_SPL_STACK_R=y
>> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
>> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
>> CONFIG_CMD_BOOTZ=y
>> CONFIG_CMD_GPT=y
>> CONFIG_CMD_MMC=y
>> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
>> CONFIG_CMD_USB=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_CMD_TIME=y
>> +CONFIG_TPL=y
>> CONFIG_SPL_OF_CONTROL=y
>> CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4"
>> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
>> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
>> CONFIG_USB_ETHER_RTL8152=y
>> CONFIG_USB_ETHER_SMSC95XX=y
>> CONFIG_USE_TINY_PRINTF=y
>> +CONFIG_SPL_TINY_MEMSET=y
>> CONFIG_ERRNO_STR=y
>
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 1/3] rk3399: orangepi: Enable TPL
2019-05-29 8:01 ` [U-Boot] " Kever Yang
@ 2019-06-01 2:39 ` Kever Yang
-1 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-06-01 2:39 UTC (permalink / raw)
To: Jagan Teki, Simon Glass, Philipp Tomsich
Cc: linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-amarula-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/,
u-boot-0aAXYlwwYIKGBzrmiIFOJg
On 05/29/2019 04:01 PM, Kever Yang wrote:
> Hi Jagan,
>
>
> On 05/09/2019 06:57 PM, Jagan Teki wrote:
>> Enable TPL for OrangePI rk3399 board.
>>
>> Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
> Reviewed-by: Kever Yang <kever.yang-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Applied to u-boot-rockchip/master, thanks!
>
> Thanks,
> - Kever
>> ---
>> configs/orangepi-rk3399_defconfig | 7 ++++---
>> 1 file changed, 4 insertions(+), 3 deletions(-)
>>
>> diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig
>> index 3f02c89983..90021bb695 100644
>> --- a/configs/orangepi-rk3399_defconfig
>> +++ b/configs/orangepi-rk3399_defconfig
>> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
>> CONFIG_SPL_LIBGENERIC_SUPPORT=y
>> CONFIG_SYS_MALLOC_F_LEN=0x4000
>> CONFIG_ROCKCHIP_RK3399=y
>> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
>> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
>> CONFIG_DEBUG_UART_BASE=0xFF1A0000
>> CONFIG_DEBUG_UART_CLOCK=24000000
>> CONFIG_SPL_STACK_R_ADDR=0x80000
>> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
>> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
>> # CONFIG_DISPLAY_CPUINFO is not set
>> CONFIG_DISPLAY_BOARDINFO_LATE=y
>> -CONFIG_SPL_TEXT_BASE=0xff8c2000
>> CONFIG_SPL_STACK_R=y
>> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
>> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
>> CONFIG_CMD_BOOTZ=y
>> CONFIG_CMD_GPT=y
>> CONFIG_CMD_MMC=y
>> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
>> CONFIG_CMD_USB=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_CMD_TIME=y
>> +CONFIG_TPL=y
>> CONFIG_SPL_OF_CONTROL=y
>> CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
>> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
>> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
>> CONFIG_USB_ETHER_RTL8152=y
>> CONFIG_USB_ETHER_SMSC95XX=y
>> CONFIG_USE_TINY_PRINTF=y
>> +CONFIG_SPL_TINY_MEMSET=y
>> CONFIG_ERRNO_STR=y
>
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 1/3] rk3399: orangepi: Enable TPL
@ 2019-06-01 2:39 ` Kever Yang
0 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-06-01 2:39 UTC (permalink / raw)
To: u-boot
On 05/29/2019 04:01 PM, Kever Yang wrote:
> Hi Jagan,
>
>
> On 05/09/2019 06:57 PM, Jagan Teki wrote:
>> Enable TPL for OrangePI rk3399 board.
>>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Applied to u-boot-rockchip/master, thanks!
>
> Thanks,
> - Kever
>> ---
>> configs/orangepi-rk3399_defconfig | 7 ++++---
>> 1 file changed, 4 insertions(+), 3 deletions(-)
>>
>> diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig
>> index 3f02c89983..90021bb695 100644
>> --- a/configs/orangepi-rk3399_defconfig
>> +++ b/configs/orangepi-rk3399_defconfig
>> @@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
>> CONFIG_SPL_LIBGENERIC_SUPPORT=y
>> CONFIG_SYS_MALLOC_F_LEN=0x4000
>> CONFIG_ROCKCHIP_RK3399=y
>> -CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
>> +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
>> CONFIG_DEBUG_UART_BASE=0xFF1A0000
>> CONFIG_DEBUG_UART_CLOCK=24000000
>> CONFIG_SPL_STACK_R_ADDR=0x80000
>> @@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
>> CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
>> # CONFIG_DISPLAY_CPUINFO is not set
>> CONFIG_DISPLAY_BOARDINFO_LATE=y
>> -CONFIG_SPL_TEXT_BASE=0xff8c2000
>> CONFIG_SPL_STACK_R=y
>> -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
>> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
>> CONFIG_CMD_BOOTZ=y
>> CONFIG_CMD_GPT=y
>> CONFIG_CMD_MMC=y
>> @@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
>> CONFIG_CMD_USB=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_CMD_TIME=y
>> +CONFIG_TPL=y
>> CONFIG_SPL_OF_CONTROL=y
>> CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
>> CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
>> @@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
>> CONFIG_USB_ETHER_RTL8152=y
>> CONFIG_USB_ETHER_SMSC95XX=y
>> CONFIG_USE_TINY_PRINTF=y
>> +CONFIG_SPL_TINY_MEMSET=y
>> CONFIG_ERRNO_STR=y
>
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 3/3] doc: rockchip: Add doc for rk3399 TPL build/flash
2019-05-29 8:02 ` [U-Boot] " Kever Yang
@ 2019-06-01 2:39 ` Kever Yang
-1 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-06-01 2:39 UTC (permalink / raw)
To: Jagan Teki, Simon Glass, Philipp Tomsich
Cc: linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-amarula-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/,
u-boot-0aAXYlwwYIKGBzrmiIFOJg
On 05/29/2019 04:02 PM, Kever Yang wrote:
> Hi Jagan,
>
>
> On 05/09/2019 06:57 PM, Jagan Teki wrote:
>> This patch add documentation for TPL build and flashing steps
>> for rk3399 boards.
>>
>> Add full boot log for future reference.
>>
>> Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
> Reviewed-by: Kever Yang <kever.yang-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Applied to u-boot-rockchip/master, thanks!
>
> Thanks,
> - Kever
>> ---
>> doc/README.rockchip | 51 ++++++++++++++++++++++++++++++++++++++++++++-
>> 1 file changed, 50 insertions(+), 1 deletion(-)
>>
>> diff --git a/doc/README.rockchip b/doc/README.rockchip
>> index ca4d6473b0..264f7e4994 100644
>> --- a/doc/README.rockchip
>> +++ b/doc/README.rockchip
>> @@ -173,7 +173,10 @@ For example:
>> => make u-boot.itb
>>
>> (Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
>> - spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL)
>> + spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
>> +
>> + If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
>> + if CONFIG_TPL_OF_CONTROL not enabled)
>>
>> Writing to the board with USB
>> =============================
>> @@ -455,6 +458,52 @@ Net: eth0: ethernet@fe300000
>> Hit any key to stop autoboot: 0
>> =>
>>
>> +Option 3: Package the image with TPL:
>> +
>> + - Prefix rk3399 header to TPL image
>> +
>> + => cd /path/to/u-boot
>> + => ./tools/mkimage -n rk3399 -T rksd -d tpl/u-boot-tpl-dtb.bin out
>> +
>> + - Concatinate tpl with spl
>> +
>> + => cd /path/to/u-boot
>> + => cat ./spl/u-boot-spl-dtb.bin >> out
>> +
>> + - Write tpl+spl at 64th sector
>> +
>> + => sudo dd if=out of=/dev/sdc seek=64
>> +
>> + - Write U-Boot proper at 16384 sector
>> +
>> + => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
>> + => sync
>> +
>> +Put this SD (or micro-SD) card into your board and reset it. You should see
>> +something like:
>> +
>> +U-Boot TPL board init
>> +Trying to boot from BOOTROM
>> +Returning to boot ROM...
>> +
>> +U-Boot SPL board init
>> +Trying to boot from MMC1
>> +
>> +
>> +U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
>> +
>> +Model: Orange Pi RK3399 Board
>> +DRAM: 2 GiB
>> +MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0
>> +Loading Environment from MMC... OK
>> +In: serial@ff1a0000
>> +Out: serial@ff1a0000
>> +Err: serial@ff1a0000
>> +Model: Orange Pi RK3399 Board
>> +Net: eth0: ethernet@fe300000
>> +Hit any key to stop autoboot: 0
>> +=>
>> +
>> Using fastboot on rk3288
>> ========================
>> - Write GPT partition layout to mmc device which fastboot want to use it to
>
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] [PATCH 3/3] doc: rockchip: Add doc for rk3399 TPL build/flash
@ 2019-06-01 2:39 ` Kever Yang
0 siblings, 0 replies; 20+ messages in thread
From: Kever Yang @ 2019-06-01 2:39 UTC (permalink / raw)
To: u-boot
On 05/29/2019 04:02 PM, Kever Yang wrote:
> Hi Jagan,
>
>
> On 05/09/2019 06:57 PM, Jagan Teki wrote:
>> This patch add documentation for TPL build and flashing steps
>> for rk3399 boards.
>>
>> Add full boot log for future reference.
>>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Applied to u-boot-rockchip/master, thanks!
>
> Thanks,
> - Kever
>> ---
>> doc/README.rockchip | 51 ++++++++++++++++++++++++++++++++++++++++++++-
>> 1 file changed, 50 insertions(+), 1 deletion(-)
>>
>> diff --git a/doc/README.rockchip b/doc/README.rockchip
>> index ca4d6473b0..264f7e4994 100644
>> --- a/doc/README.rockchip
>> +++ b/doc/README.rockchip
>> @@ -173,7 +173,10 @@ For example:
>> => make u-boot.itb
>>
>> (Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
>> - spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL)
>> + spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
>> +
>> + If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
>> + if CONFIG_TPL_OF_CONTROL not enabled)
>>
>> Writing to the board with USB
>> =============================
>> @@ -455,6 +458,52 @@ Net: eth0: ethernet at fe300000
>> Hit any key to stop autoboot: 0
>> =>
>>
>> +Option 3: Package the image with TPL:
>> +
>> + - Prefix rk3399 header to TPL image
>> +
>> + => cd /path/to/u-boot
>> + => ./tools/mkimage -n rk3399 -T rksd -d tpl/u-boot-tpl-dtb.bin out
>> +
>> + - Concatinate tpl with spl
>> +
>> + => cd /path/to/u-boot
>> + => cat ./spl/u-boot-spl-dtb.bin >> out
>> +
>> + - Write tpl+spl at 64th sector
>> +
>> + => sudo dd if=out of=/dev/sdc seek=64
>> +
>> + - Write U-Boot proper at 16384 sector
>> +
>> + => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
>> + => sync
>> +
>> +Put this SD (or micro-SD) card into your board and reset it. You should see
>> +something like:
>> +
>> +U-Boot TPL board init
>> +Trying to boot from BOOTROM
>> +Returning to boot ROM...
>> +
>> +U-Boot SPL board init
>> +Trying to boot from MMC1
>> +
>> +
>> +U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
>> +
>> +Model: Orange Pi RK3399 Board
>> +DRAM: 2 GiB
>> +MMC: dwmmc at fe310000: 2, dwmmc at fe320000: 1, sdhci at fe330000: 0
>> +Loading Environment from MMC... OK
>> +In: serial at ff1a0000
>> +Out: serial at ff1a0000
>> +Err: serial at ff1a0000
>> +Model: Orange Pi RK3399 Board
>> +Net: eth0: ethernet at fe300000
>> +Hit any key to stop autoboot: 0
>> +=>
>> +
>> Using fastboot on rk3288
>> ========================
>> - Write GPT partition layout to mmc device which fastboot want to use it to
>
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2019-06-01 2:39 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-09 10:57 [PATCH 1/3] rk3399: orangepi: Enable TPL Jagan Teki
2019-05-09 10:57 ` [U-Boot] " Jagan Teki
[not found] ` <20190509105746.24830-1-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
2019-05-09 10:57 ` [PATCH 2/3] rk3399: nanopi4: " Jagan Teki
2019-05-09 10:57 ` [U-Boot] " Jagan Teki
[not found] ` <20190509105746.24830-2-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
2019-05-29 8:02 ` Kever Yang
2019-05-29 8:02 ` [U-Boot] " Kever Yang
2019-06-01 2:39 ` Kever Yang
2019-06-01 2:39 ` [U-Boot] " Kever Yang
2019-05-09 10:57 ` [PATCH 3/3] doc: rockchip: Add doc for rk3399 TPL build/flash Jagan Teki
2019-05-09 10:57 ` [U-Boot] " Jagan Teki
[not found] ` <20190509105746.24830-3-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
2019-05-29 8:02 ` Kever Yang
2019-05-29 8:02 ` [U-Boot] " Kever Yang
[not found] ` <b5cd9180-56c9-dd02-e6bf-4e7638902d5c-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
2019-06-01 2:39 ` Kever Yang
2019-06-01 2:39 ` [U-Boot] " Kever Yang
2019-05-29 8:06 ` [PATCH 1/3] rk3399: orangepi: Enable TPL Kever Yang
2019-05-29 8:06 ` [U-Boot] " Kever Yang
2019-05-29 8:01 ` Kever Yang
2019-05-29 8:01 ` [U-Boot] " Kever Yang
[not found] ` <3d1513a8-202a-9906-ddb0-2ed1000696f3-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
2019-06-01 2:39 ` Kever Yang
2019-06-01 2:39 ` [U-Boot] " Kever Yang
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.