Re: [PATCH v6 06/10] scsi: ufs: ufs-qcom: Set initial PHY gear to max HS gear for HW ver 4 and newer

[Nitin Rawat <quic_nitirawa@quicinc.com>]

On 11/29/2023 1:58 PM, Can Guo wrote:
> Since HW ver 4, max HS gear can be get from UFS host controller's register,
> use the max HS gear as the initial PHY gear instead of UFS_HS_G2, so that
> we don't need to update the hard code for newer targets in future.
> 
> Signed-off-by: Can Guo <quic_cang@quicinc.com>
> ---
>   drivers/ufs/host/ufs-qcom.c | 21 +++++++++++++++------
>   1 file changed, 15 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index aca6199..30f4ca6 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -1060,6 +1060,20 @@ static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
>   		hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
>   }
>   
> +static void ufs_qcom_set_phy_gear(struct ufs_qcom_host *host)
> +{
> +	struct ufs_host_params *host_params = &host->host_params;
> +
> +	host->phy_gear = host_params->hs_tx_gear;
> +
> +	/*
> +	 * Power up the PHY using the minimum supported gear (UFS_HS_G2).
> +	 * Switching to max gear will be performed during reinit if supported.
> +	 */
> +	if (host->hw_ver.major < 0x4)
> +		host->phy_gear = UFS_HS_G2;
> +}
> +
>   static void ufs_qcom_set_host_params(struct ufs_hba *hba)
>   {
>   	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> @@ -1296,6 +1310,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)
>   	ufs_qcom_set_caps(hba);
>   	ufs_qcom_advertise_quirks(hba);
>   	ufs_qcom_set_host_params(hba);
> +	ufs_qcom_set_phy_gear(host);
>   
>   	err = ufs_qcom_ice_init(host);
>   	if (err)
> @@ -1313,12 +1328,6 @@ static int ufs_qcom_init(struct ufs_hba *hba)
>   		dev_warn(dev, "%s: failed to configure the testbus %d\n",
>   				__func__, err);
>   
> -	/*
> -	 * Power up the PHY using the minimum supported gear (UFS_HS_G2).
> -	 * Switching to max gear will be performed during reinit if supported.
> -	 */
> -	host->phy_gear = UFS_HS_G2;
> -
>   	return 0;
>   
>   out_variant_clear:

Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>