[PATCH 01/41] ARM: dts: ape6evm: Name serial port pfc subnode after device name

[PATCH 01/41] ARM: dts: ape6evm: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIFA0 after its device
name, instead of after the serial port alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a73a4-ape6evm.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
index 740e5d23f7c7..5bccc7d229d7 100644
--- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts
+++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
@@ -188,7 +188,7 @@
 };
 
 &pfc {
-	scifa0_pins: serial0 {
+	scifa0_pins: scifa0 {
 		groups = "scifa0_data";
 		function = "scifa0";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 01/41] ARM: dts: ape6evm: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIFA0 after its device
name, instead of after the serial port alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a73a4-ape6evm.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
index 740e5d23f7c7..5bccc7d229d7 100644
--- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts
+++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
@@ -188,7 +188,7 @@
 };
 
 &pfc {
-	scifa0_pins: serial0 {
+	scifa0_pins: scifa0 {
 		groups = "scifa0_data";
 		function = "scifa0";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 02/41] ARM: dts: ape6evm: Name mmc pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for MMC0 after its device name,
instead of using the generic and indexless "mmc".

This avoids conflicts when enabling support for more MMC interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a73a4-ape6evm.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
index 5bccc7d229d7..ec7c86e06538 100644
--- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts
+++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
@@ -193,7 +193,7 @@
 		function = "scifa0";
 	};
 
-	mmc0_pins: mmc {
+	mmc0_pins: mmc0 {
 		groups = "mmc0_data8", "mmc0_ctrl";
 		function = "mmc0";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 02/41] ARM: dts: ape6evm: Name mmc pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for MMC0 after its device name,
instead of using the generic and indexless "mmc".

This avoids conflicts when enabling support for more MMC interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a73a4-ape6evm.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
index 5bccc7d229d7..ec7c86e06538 100644
--- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts
+++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
@@ -193,7 +193,7 @@
 		function = "scifa0";
 	};
 
-	mmc0_pins: mmc {
+	mmc0_pins: mmc0 {
 		groups = "mmc0_data8", "mmc0_ctrl";
 		function = "mmc0";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 03/41] ARM: dts: armadillo800eva: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIFA1 after its device
name, instead of after the serial port alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7740-armadillo800eva.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
index 162049516685..6866f61a350c 100644
--- a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
+++ b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
@@ -232,7 +232,7 @@
 		function = "gether";
 	};
 
-	scifa1_pins: serial1 {
+	scifa1_pins: scifa1 {
 		groups = "scifa1_data";
 		function = "scifa1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 03/41] ARM: dts: armadillo800eva: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIFA1 after its device
name, instead of after the serial port alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7740-armadillo800eva.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
index 162049516685..6866f61a350c 100644
--- a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
+++ b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
@@ -232,7 +232,7 @@
 		function = "gether";
 	};
 
-	scifa1_pins: serial1 {
+	scifa1_pins: scifa1 {
 		groups = "scifa1_data";
 		function = "scifa1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 04/41] ARM: dts: bockw: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIF0 after its device
name, instead of after the serial port alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7778-bockw.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7778-bockw.dts b/arch/arm/boot/dts/r8a7778-bockw.dts
index 0a0bd3b6bb40..211d239d9041 100644
--- a/arch/arm/boot/dts/r8a7778-bockw.dts
+++ b/arch/arm/boot/dts/r8a7778-bockw.dts
@@ -129,7 +129,7 @@
 	pinctrl-0 = <&scif_clk_pins>;
 	pinctrl-names = "default";
 
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data_a", "scif0_ctrl";
 		function = "scif0";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 04/41] ARM: dts: bockw: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIF0 after its device
name, instead of after the serial port alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7778-bockw.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7778-bockw.dts b/arch/arm/boot/dts/r8a7778-bockw.dts
index 0a0bd3b6bb40..211d239d9041 100644
--- a/arch/arm/boot/dts/r8a7778-bockw.dts
+++ b/arch/arm/boot/dts/r8a7778-bockw.dts
@@ -129,7 +129,7 @@
 	pinctrl-0 = <&scif_clk_pins>;
 	pinctrl-names = "default";
 
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data_a", "scif0_ctrl";
 		function = "scif0";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 05/41] ARM: dts: marzen: Name serial port pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for SCIF2 and SCIF4 after
their device names, instead of using some arbitrary names that look like
serial port aliases, but differ from the actual aliases.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7779-marzen.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7779-marzen.dts b/arch/arm/boot/dts/r8a7779-marzen.dts
index cec79a6347c0..013e6f510b0f 100644
--- a/arch/arm/boot/dts/r8a7779-marzen.dts
+++ b/arch/arm/boot/dts/r8a7779-marzen.dts
@@ -195,12 +195,12 @@
 		};
 	};
 
-	scif2_pins: serial2 {
+	scif2_pins: scif2 {
 		groups = "scif2_data_c";
 		function = "scif2";
 	};
 
-	scif4_pins: serial4 {
+	scif4_pins: scif4 {
 		groups = "scif4_data";
 		function = "scif4";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 05/41] ARM: dts: marzen: Name serial port pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for SCIF2 and SCIF4 after
their device names, instead of using some arbitrary names that look like
serial port aliases, but differ from the actual aliases.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7779-marzen.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7779-marzen.dts b/arch/arm/boot/dts/r8a7779-marzen.dts
index cec79a6347c0..013e6f510b0f 100644
--- a/arch/arm/boot/dts/r8a7779-marzen.dts
+++ b/arch/arm/boot/dts/r8a7779-marzen.dts
@@ -195,12 +195,12 @@
 		};
 	};
 
-	scif2_pins: serial2 {
+	scif2_pins: scif2 {
 		groups = "scif2_data_c";
 		function = "scif2";
 	};
 
-	scif4_pins: serial4 {
+	scif4_pins: scif4 {
 		groups = "scif4_data";
 		function = "scif4";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 06/41] ARM: dts: lager: Name serial port pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for SCIF0 and SCIFA1 after
their device names, instead of after the serial port aliases.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 9d20ace33b01..c6803977b427 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -317,7 +317,7 @@
 		function = "du";
 	};
 
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data";
 		function = "scif0";
 	};
@@ -337,7 +337,7 @@
 		function = "intc";
 	};
 
-	scifa1_pins: serial1 {
+	scifa1_pins: scifa1 {
 		groups = "scifa1_data";
 		function = "scifa1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 06/41] ARM: dts: lager: Name serial port pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for SCIF0 and SCIFA1 after
their device names, instead of after the serial port aliases.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 9d20ace33b01..c6803977b427 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -317,7 +317,7 @@
 		function = "du";
 	};
 
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data";
 		function = "scif0";
 	};
@@ -337,7 +337,7 @@
 		function = "intc";
 	};
 
-	scifa1_pins: serial1 {
+	scifa1_pins: scifa1 {
 		groups = "scifa1_data";
 		function = "scifa1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 07/41] ARM: dts: lager: Name spi pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for QSPI and MSIOF1 after
their device names, instead of after the spi interface aliases.

This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index c6803977b427..09b633f5ad07 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -371,12 +371,12 @@
 		function = "mmc1";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
 
-	msiof1_pins: spi2 {
+	msiof1_pins: msiof1 {
 		groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
 				 "msiof1_tx";
 		function = "msiof1";
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 07/41] ARM: dts: lager: Name spi pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for QSPI and MSIOF1 after
their device names, instead of after the spi interface aliases.

This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index c6803977b427..09b633f5ad07 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -371,12 +371,12 @@
 		function = "mmc1";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
 
-	msiof1_pins: spi2 {
+	msiof1_pins: msiof1 {
 		groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
 				 "msiof1_tx";
 		function = "msiof1";
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 08/41] ARM: dts: lager: Name vin pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for VIN1 after its device name,
instead of using the generic and indexless "vin".

This avoids conflicts when enabling support for more video inputs later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 09b633f5ad07..52b56fcaddf2 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -427,7 +427,7 @@
 		function = "usb2";
 	};
 
-	vin1_pins: vin {
+	vin1_pins: vin1 {
 		groups = "vin1_data8", "vin1_clk";
 		function = "vin1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 08/41] ARM: dts: lager: Name vin pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for VIN1 after its device name,
instead of using the generic and indexless "vin".

This avoids conflicts when enabling support for more video inputs later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 09b633f5ad07..52b56fcaddf2 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -427,7 +427,7 @@
 		function = "usb2";
 	};
 
-	vin1_pins: vin {
+	vin1_pins: vin1 {
 		groups = "vin1_data8", "vin1_clk";
 		function = "vin1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 09/41] ARM: dts: koelsch: Name serial port pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791-koelsch.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 20fbc8c36a78..73e5ecf036e1 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -332,12 +332,12 @@
 		function = "du";
 	};
 
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data_d";
 		function = "scif0";
 	};
 
-	scif1_pins: serial1 {
+	scif1_pins: scif1 {
 		groups = "scif1_data_d";
 		function = "scif1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 09/41] ARM: dts: koelsch: Name serial port pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791-koelsch.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 20fbc8c36a78..73e5ecf036e1 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -332,12 +332,12 @@
 		function = "du";
 	};
 
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data_d";
 		function = "scif0";
 	};
 
-	scif1_pins: serial1 {
+	scif1_pins: scif1 {
 		groups = "scif1_data_d";
 		function = "scif1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 10/41] ARM: dts: koelsch: Name spi pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for QSPI and MSIOF0 after
their device names, instead of after the spi interface aliases.

This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791-koelsch.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 73e5ecf036e1..f8a7d090fd01 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -372,12 +372,12 @@
 		function = "sdhi2";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
 
-	msiof0_pins: spi1 {
+	msiof0_pins: msiof0 {
 		groups = "msiof0_clk", "msiof0_sync", "msiof0_rx",
 				 "msiof0_tx";
 		function = "msiof0";
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 10/41] ARM: dts: koelsch: Name spi pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for QSPI and MSIOF0 after
their device names, instead of after the spi interface aliases.

This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791-koelsch.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 73e5ecf036e1..f8a7d090fd01 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -372,12 +372,12 @@
 		function = "sdhi2";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
 
-	msiof0_pins: spi1 {
+	msiof0_pins: msiof0 {
 		groups = "msiof0_clk", "msiof0_sync", "msiof0_rx",
 				 "msiof0_tx";
 		function = "msiof0";
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 11/41] ARM: dts: porter: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIF0 after its device
name, instead of after the serial port alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791-porter.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index e9151e946da8..85d109a5f43c 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -142,7 +142,7 @@
 };
 
 &pfc {
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data_d";
 		function = "scif0";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 11/41] ARM: dts: porter: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIF0 after its device
name, instead of after the serial port alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791-porter.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index e9151e946da8..85d109a5f43c 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -142,7 +142,7 @@
 };
 
 &pfc {
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data_d";
 		function = "scif0";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 12/41] ARM: dts: porter: Name spi pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.

This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791-porter.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index 85d109a5f43c..6761d11d3f9e 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -167,7 +167,7 @@
 		function = "sdhi2";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 12/41] ARM: dts: porter: Name spi pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.

This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791-porter.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index 85d109a5f43c..6761d11d3f9e 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -167,7 +167,7 @@
 		function = "sdhi2";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 13/41] ARM: dts: gose: Name serial port pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7793-gose.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index f748360ee857..995e1e0fb1ff 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -320,12 +320,12 @@
 		function = "du";
 	};
 
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data_d";
 		function = "scif0";
 	};
 
-	scif1_pins: serial1 {
+	scif1_pins: scif1 {
 		groups = "scif1_data_d";
 		function = "scif1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 13/41] ARM: dts: gose: Name serial port pfc subnodes after device names

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7793-gose.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index f748360ee857..995e1e0fb1ff 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -320,12 +320,12 @@
 		function = "du";
 	};
 
-	scif0_pins: serial0 {
+	scif0_pins: scif0 {
 		groups = "scif0_data_d";
 		function = "scif0";
 	};
 
-	scif1_pins: serial1 {
+	scif1_pins: scif1 {
 		groups = "scif1_data_d";
 		function = "scif1";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 14/41] ARM: dts: gose: Name spi pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.

This avoids conflicts when enabling support for more spi interfaces later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7793-gose.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index 995e1e0fb1ff..90af18600124 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -360,7 +360,7 @@
 		renesas,function = "sdhi2";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 14/41] ARM: dts: gose: Name spi pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.

This avoids conflicts when enabling support for more spi interfaces later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7793-gose.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index 995e1e0fb1ff..90af18600124 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -360,7 +360,7 @@
 		renesas,function = "sdhi2";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 15/41] ARM: dts: alt: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-alt.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index 383ad791f1db..1335664b2f88 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -111,7 +111,7 @@
 		function = "du";
 	};
 
-	scif2_pins: serial2 {
+	scif2_pins: scif2 {
 		groups = "scif2_data";
 		function = "scif2";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 15/41] ARM: dts: alt: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-alt.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index 383ad791f1db..1335664b2f88 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -111,7 +111,7 @@
 		function = "du";
 	};
 
-	scif2_pins: serial2 {
+	scif2_pins: scif2 {
 		groups = "scif2_data";
 		function = "scif2";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 16/41] ARM: dts: alt: Name spi pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.

This avoids conflicts when enabling support for more spi interfaces later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-alt.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index 1335664b2f88..1ad37d431a2a 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -147,7 +147,7 @@
 };
 
 &pfc {
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 16/41] ARM: dts: alt: Name spi pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.

This avoids conflicts when enabling support for more spi interfaces later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-alt.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index 1335664b2f88..1ad37d431a2a 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -147,7 +147,7 @@
 };
 
 &pfc {
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 17/41] ARM: dts: silk: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-silk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index b8c7a63c5ec4..7e88f6fe55cd 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -129,7 +129,7 @@
 	pinctrl-0 = <&scif_clk_pins>;
 	pinctrl-names = "default";
 
-	scif2_pins: serial2 {
+	scif2_pins: scif2 {
 		groups = "scif2_data";
 		function = "scif2";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 17/41] ARM: dts: silk: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.

This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-silk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index b8c7a63c5ec4..7e88f6fe55cd 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -129,7 +129,7 @@
 	pinctrl-0 = <&scif_clk_pins>;
 	pinctrl-names = "default";
 
-	scif2_pins: serial2 {
+	scif2_pins: scif2 {
 		groups = "scif2_data";
 		function = "scif2";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 18/41] ARM: dts: silk: Name spi pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.

This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-silk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index 7e88f6fe55cd..488de730bee8 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -164,7 +164,7 @@
 		function = "sdhi1";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 18/41] ARM: dts: silk: Name spi pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.

This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-silk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index 7e88f6fe55cd..488de730bee8 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -164,7 +164,7 @@
 		function = "sdhi1";
 	};
 
-	qspi_pins: spi0 {
+	qspi_pins: qspi {
 		groups = "qspi_ctrl", "qspi_data4";
 		function = "qspi";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 19/41] ARM: dts: kzm9g: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIFA4 after its device
name, instead of after the serial port alias.

This avoids conflicts when adding support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/sh73a0-kzm9g.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts
index 36567cbf2e1c..1df68b167033 100644
--- a/arch/arm/boot/dts/sh73a0-kzm9g.dts
+++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts
@@ -352,7 +352,7 @@
 		};
 	};
 
-	scifa4_pins: serial4 {
+	scifa4_pins: scifa4 {
 		groups = "scifa4_data", "scifa4_ctrl";
 		function = "scifa4";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 19/41] ARM: dts: kzm9g: Name serial port pfc subnode after device name

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Name the Pin Function Controller subnode for SCIFA4 after its device
name, instead of after the serial port alias.

This avoids conflicts when adding support for more serial ports later,
either here or in a DT overlay.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/sh73a0-kzm9g.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts
index 36567cbf2e1c..1df68b167033 100644
--- a/arch/arm/boot/dts/sh73a0-kzm9g.dts
+++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts
@@ -352,7 +352,7 @@
 		};
 	};
 
-	scifa4_pins: serial4 {
+	scifa4_pins: scifa4 {
 		groups = "scifa4_data", "scifa4_ctrl";
 		function = "scifa4";
 	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 20/41] ARM: dts: r8a7792: add clock index macros

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add macros usable by the device tree sources to reference the R8A7792
clocks  by index.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 include/dt-bindings/clock/r8a7792-clock.h | 102 ++++++++++++++++++++++++++++++
 1 file changed, 102 insertions(+)
 create mode 100644 include/dt-bindings/clock/r8a7792-clock.h

diff --git a/include/dt-bindings/clock/r8a7792-clock.h b/include/dt-bindings/clock/r8a7792-clock.h
new file mode 100644
index 000000000000..949801eb0652
--- /dev/null
+++ b/include/dt-bindings/clock/r8a7792-clock.h
@@ -0,0 +1,102 @@
+/*
+ * Copyright (C) 2016 Cogent Embedded, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_R8A7792_H__
+#define __DT_BINDINGS_CLOCK_R8A7792_H__
+
+/* CPG */
+#define R8A7792_CLK_MAIN		0
+#define R8A7792_CLK_PLL0		1
+#define R8A7792_CLK_PLL1		2
+#define R8A7792_CLK_PLL3		3
+#define R8A7792_CLK_LB			4
+#define R8A7792_CLK_QSPI		5
+#define R8A7792_CLK_Z			6
+#define R8A7792_CLK_ADSP		7
+
+/* MSTP0 */
+#define R8A7792_CLK_MSIOF0		0
+
+/* MSTP1 */
+#define R8A7792_CLK_TMU1		11
+#define R8A7792_CLK_TMU3		21
+#define R8A7792_CLK_TMU2		22
+#define R8A7792_CLK_CMT0		24
+#define R8A7792_CLK_TMU0		25
+#define R8A7792_CLK_VSP1DU1		27
+#define R8A7792_CLK_VSP1DU0		28
+#define R8A7792_CLK_VSP1_SY		31
+
+/* MSTP2 */
+#define R8A7792_CLK_MSIOF1		8
+#define R8A7792_CLK_SYS_DMAC1		18
+#define R8A7792_CLK_SYS_DMAC0		19
+
+/* MSTP3 */
+#define R8A7792_CLK_TPU0		4
+#define R8A7792_CLK_SDHI0		14
+#define R8A7792_CLK_CMT1		29
+
+/* MSTP4 */
+#define R8A7792_CLK_IRQC		7
+
+/* MSTP5 */
+#define R8A7792_CLK_AUDIO_DMAC0		2
+#define R8A7792_CLK_THERMAL		22
+#define R8A7792_CLK_PWM			23
+
+/* MSTP7 */
+#define R8A7792_CLK_HSCIF1		16
+#define R8A7792_CLK_HSCIF0		17
+#define R8A7792_CLK_SCIF3		18
+#define R8A7792_CLK_SCIF2		19
+#define R8A7792_CLK_SCIF1		20
+#define R8A7792_CLK_SCIF0		21
+#define R8A7792_CLK_DU1			23
+#define R8A7792_CLK_DU0			24
+
+/* MSTP8 */
+#define R8A7792_CLK_VIN5		4
+#define R8A7792_CLK_VIN4		5
+#define R8A7792_CLK_VIN3		8
+#define R8A7792_CLK_VIN2		9
+#define R8A7792_CLK_VIN1		10
+#define R8A7792_CLK_VIN0		11
+#define R8A7792_CLK_ETHERAVB		12
+
+/* MSTP9 */
+#define R8A7792_CLK_GPIO7		4
+#define R8A7792_CLK_GPIO6		5
+#define R8A7792_CLK_GPIO5		7
+#define R8A7792_CLK_GPIO4		8
+#define R8A7792_CLK_GPIO3		9
+#define R8A7792_CLK_GPIO2		10
+#define R8A7792_CLK_GPIO1		11
+#define R8A7792_CLK_GPIO0		12
+#define R8A7792_CLK_GPIO11		13
+#define R8A7792_CLK_GPIO10		14
+#define R8A7792_CLK_CAN1		15
+#define R8A7792_CLK_CAN0		16
+#define R8A7792_CLK_QSPI_MOD		17
+#define R8A7792_CLK_GPIO9		19
+#define R8A7792_CLK_GPIO8		21
+#define R8A7792_CLK_I2C5		25
+#define R8A7792_CLK_IICDVFS		26
+#define R8A7792_CLK_I2C4		27
+#define R8A7792_CLK_I2C3		28
+#define R8A7792_CLK_I2C2		29
+#define R8A7792_CLK_I2C1		30
+#define R8A7792_CLK_I2C0		31
+
+/* MSTP10 */
+#define R8A7792_CLK_SSI_ALL		5
+#define R8A7792_CLK_SSI4		11
+#define R8A7792_CLK_SSI3		12
+
+#endif /* __DT_BINDINGS_CLOCK_R8A7792_H__ */
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 20/41] ARM: dts: r8a7792: add clock index macros

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add macros usable by the device tree sources to reference the R8A7792
clocks  by index.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 include/dt-bindings/clock/r8a7792-clock.h | 102 ++++++++++++++++++++++++++++++
 1 file changed, 102 insertions(+)
 create mode 100644 include/dt-bindings/clock/r8a7792-clock.h

diff --git a/include/dt-bindings/clock/r8a7792-clock.h b/include/dt-bindings/clock/r8a7792-clock.h
new file mode 100644
index 000000000000..949801eb0652
--- /dev/null
+++ b/include/dt-bindings/clock/r8a7792-clock.h
@@ -0,0 +1,102 @@
+/*
+ * Copyright (C) 2016 Cogent Embedded, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_R8A7792_H__
+#define __DT_BINDINGS_CLOCK_R8A7792_H__
+
+/* CPG */
+#define R8A7792_CLK_MAIN		0
+#define R8A7792_CLK_PLL0		1
+#define R8A7792_CLK_PLL1		2
+#define R8A7792_CLK_PLL3		3
+#define R8A7792_CLK_LB			4
+#define R8A7792_CLK_QSPI		5
+#define R8A7792_CLK_Z			6
+#define R8A7792_CLK_ADSP		7
+
+/* MSTP0 */
+#define R8A7792_CLK_MSIOF0		0
+
+/* MSTP1 */
+#define R8A7792_CLK_TMU1		11
+#define R8A7792_CLK_TMU3		21
+#define R8A7792_CLK_TMU2		22
+#define R8A7792_CLK_CMT0		24
+#define R8A7792_CLK_TMU0		25
+#define R8A7792_CLK_VSP1DU1		27
+#define R8A7792_CLK_VSP1DU0		28
+#define R8A7792_CLK_VSP1_SY		31
+
+/* MSTP2 */
+#define R8A7792_CLK_MSIOF1		8
+#define R8A7792_CLK_SYS_DMAC1		18
+#define R8A7792_CLK_SYS_DMAC0		19
+
+/* MSTP3 */
+#define R8A7792_CLK_TPU0		4
+#define R8A7792_CLK_SDHI0		14
+#define R8A7792_CLK_CMT1		29
+
+/* MSTP4 */
+#define R8A7792_CLK_IRQC		7
+
+/* MSTP5 */
+#define R8A7792_CLK_AUDIO_DMAC0		2
+#define R8A7792_CLK_THERMAL		22
+#define R8A7792_CLK_PWM			23
+
+/* MSTP7 */
+#define R8A7792_CLK_HSCIF1		16
+#define R8A7792_CLK_HSCIF0		17
+#define R8A7792_CLK_SCIF3		18
+#define R8A7792_CLK_SCIF2		19
+#define R8A7792_CLK_SCIF1		20
+#define R8A7792_CLK_SCIF0		21
+#define R8A7792_CLK_DU1			23
+#define R8A7792_CLK_DU0			24
+
+/* MSTP8 */
+#define R8A7792_CLK_VIN5		4
+#define R8A7792_CLK_VIN4		5
+#define R8A7792_CLK_VIN3		8
+#define R8A7792_CLK_VIN2		9
+#define R8A7792_CLK_VIN1		10
+#define R8A7792_CLK_VIN0		11
+#define R8A7792_CLK_ETHERAVB		12
+
+/* MSTP9 */
+#define R8A7792_CLK_GPIO7		4
+#define R8A7792_CLK_GPIO6		5
+#define R8A7792_CLK_GPIO5		7
+#define R8A7792_CLK_GPIO4		8
+#define R8A7792_CLK_GPIO3		9
+#define R8A7792_CLK_GPIO2		10
+#define R8A7792_CLK_GPIO1		11
+#define R8A7792_CLK_GPIO0		12
+#define R8A7792_CLK_GPIO11		13
+#define R8A7792_CLK_GPIO10		14
+#define R8A7792_CLK_CAN1		15
+#define R8A7792_CLK_CAN0		16
+#define R8A7792_CLK_QSPI_MOD		17
+#define R8A7792_CLK_GPIO9		19
+#define R8A7792_CLK_GPIO8		21
+#define R8A7792_CLK_I2C5		25
+#define R8A7792_CLK_IICDVFS		26
+#define R8A7792_CLK_I2C4		27
+#define R8A7792_CLK_I2C3		28
+#define R8A7792_CLK_I2C2		29
+#define R8A7792_CLK_I2C1		30
+#define R8A7792_CLK_I2C0		31
+
+/* MSTP10 */
+#define R8A7792_CLK_SSI_ALL		5
+#define R8A7792_CLK_SSI4		11
+#define R8A7792_CLK_SSI3		12
+
+#endif /* __DT_BINDINGS_CLOCK_R8A7792_H__ */
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 21/41] ARM: dts: r8a7792: add power domain index macros

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add macros usable by the device tree sources to reference R8A7792 SYSC power
domains by index.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 include/dt-bindings/power/r8a7792-sysc.h | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
 create mode 100644 include/dt-bindings/power/r8a7792-sysc.h

diff --git a/include/dt-bindings/power/r8a7792-sysc.h b/include/dt-bindings/power/r8a7792-sysc.h
new file mode 100644
index 000000000000..74f4a78e29aa
--- /dev/null
+++ b/include/dt-bindings/power/r8a7792-sysc.h
@@ -0,0 +1,26 @@
+/*
+ * Copyright (C) 2016 Cogent Embedded Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+#ifndef __DT_BINDINGS_POWER_R8A7792_SYSC_H__
+#define __DT_BINDINGS_POWER_R8A7792_SYSC_H__
+
+/*
+ * These power domain indices match the numbers of the interrupt bits
+ * representing the power areas in the various Interrupt Registers
+ * (e.g. SYSCISR, Interrupt Status Register)
+ */
+
+#define R8A7792_PD_CA15_CPU0		0
+#define R8A7792_PD_CA15_CPU1		1
+#define R8A7792_PD_CA15_SCU		12
+#define R8A7792_PD_SGX			20
+#define R8A7792_PD_IMP			24
+
+/* Always-on power area */
+#define R8A7792_PD_ALWAYS_ON		32
+
+#endif /* __DT_BINDINGS_POWER_R8A7792_SYSC_H__ */
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 21/41] ARM: dts: r8a7792: add power domain index macros

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add macros usable by the device tree sources to reference R8A7792 SYSC power
domains by index.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 include/dt-bindings/power/r8a7792-sysc.h | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
 create mode 100644 include/dt-bindings/power/r8a7792-sysc.h

diff --git a/include/dt-bindings/power/r8a7792-sysc.h b/include/dt-bindings/power/r8a7792-sysc.h
new file mode 100644
index 000000000000..74f4a78e29aa
--- /dev/null
+++ b/include/dt-bindings/power/r8a7792-sysc.h
@@ -0,0 +1,26 @@
+/*
+ * Copyright (C) 2016 Cogent Embedded Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+#ifndef __DT_BINDINGS_POWER_R8A7792_SYSC_H__
+#define __DT_BINDINGS_POWER_R8A7792_SYSC_H__
+
+/*
+ * These power domain indices match the numbers of the interrupt bits
+ * representing the power areas in the various Interrupt Registers
+ * (e.g. SYSCISR, Interrupt Status Register)
+ */
+
+#define R8A7792_PD_CA15_CPU0		0
+#define R8A7792_PD_CA15_CPU1		1
+#define R8A7792_PD_CA15_SCU		12
+#define R8A7792_PD_SGX			20
+#define R8A7792_PD_IMP			24
+
+/* Always-on power area */
+#define R8A7792_PD_ALWAYS_ON		32
+
+#endif /* __DT_BINDINGS_POWER_R8A7792_SYSC_H__ */
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 22/41] ARM: dts: r8a7792: initial SoC device tree

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

The initial R8A7792 SoC device tree including CPU cores, GIC, timer, SYSC,
and the required  clock descriptions.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 170 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 170 insertions(+)
 create mode 100644 arch/arm/boot/dts/r8a7792.dtsi

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
new file mode 100644
index 000000000000..33f2362a1f52
--- /dev/null
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -0,0 +1,170 @@
+/*
+ * Device Tree Source for the r8a7792 SoC
+ *
+ * Copyright (C) 2016 Cogent Embedded Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/clock/r8a7792-clock.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a7792-sysc.h>
+
+/ {
+	compatible = "renesas,r8a7792";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0>;
+			clock-frequency = <1000000000>;
+			clocks = <&cpg_clocks R8A7792_CLK_Z>;
+			power-domains = <&sysc R8A7792_PD_CA15_CPU0>;
+			next-level-cache = <&L2_CA15>;
+		};
+
+		L2_CA15: cache-controller@0 {
+			compatible = "cache";
+			reg = <0>;
+			cache-unified;
+			cache-level = <2>;
+			power-domains = <&sysc R8A7792_PD_CA15_SCU>;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gic: interrupt-controller@f1001000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0 0xf1001000 0 0x1000>,
+			      <0 0xf1002000 0 0x1000>,
+			      <0 0xf1004000 0 0x2000>,
+			      <0 0xf1006000 0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		timer {
+			compatible = "arm,armv7-timer";
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_LOW)>;
+		};
+
+		sysc: system-controller@e6180000 {
+			compatible = "renesas,r8a7792-sysc";
+			reg = <0 0xe6180000 0 0x0200>;
+			#power-domain-cells = <1>;
+		};
+
+		/* Special CPG clocks */
+		cpg_clocks: cpg_clocks@e6150000 {
+			compatible = "renesas,r8a7792-cpg-clocks",
+				     "renesas,rcar-gen2-cpg-clocks";
+			reg = <0 0xe6150000 0 0x1000>;
+			clocks = <&extal_clk>;
+			#clock-cells = <1>;
+			clock-output-names = "main", "pll0", "pll1", "pll3",
+					     "lb", "qspi", "z", "adsp";
+			#power-domain-cells = <0>;
+		};
+
+		/* Fixed factor clocks */
+		zs_clk: zs {
+			compatible = "fixed-factor-clock";
+			clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+			#clock-cells = <0>;
+			clock-div = <6>;
+			clock-mult = <1>;
+		};
+		p_clk: p {
+			compatible = "fixed-factor-clock";
+			clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+			#clock-cells = <0>;
+			clock-div = <24>;
+			clock-mult = <1>;
+		};
+		cp_clk: cp {
+			compatible = "fixed-factor-clock";
+			clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+			#clock-cells = <0>;
+			clock-div = <48>;
+			clock-mult = <1>;
+		};
+
+		/* Gate clocks */
+		mstp2_clks: mstp2_clks@e6150138 {
+			compatible = "renesas,r8a7792-mstp-clocks",
+				     "renesas,cpg-mstp-clocks";
+			reg = <0 0xe6150138 0 4>, <0 0xe6150040 0 4>;
+			clocks = <&zs_clk>, <&zs_clk>;
+			#clock-cells = <1>;
+			clock-indices = <
+				R8A7792_CLK_SYS_DMAC1 R8A7792_CLK_SYS_DMAC0
+			>;
+			clock-output-names = "sys-dmac1", "sys-dmac0";
+		};
+		mstp4_clks: mstp4_clks@e6150140 {
+			compatible = "renesas,r8a7792-mstp-clocks",
+				     "renesas,cpg-mstp-clocks";
+			reg = <0 0xe6150140 0 4>, <0 0xe615004c 0 4>;
+			clocks = <&cp_clk>;
+			#clock-cells = <1>;
+			clock-indices = <R8A7792_CLK_IRQC>;
+			clock-output-names = "irqc";
+		};
+		mstp7_clks: mstp7_clks@e615014c {
+			compatible = "renesas,r8a7792-mstp-clocks",
+				     "renesas,cpg-mstp-clocks";
+			reg = <0 0xe615014c 0 4>, <0 0xe61501c4 0 4>;
+			clocks = <&zs_clk>, <&zs_clk>, <&p_clk>, <&p_clk>,
+				 <&p_clk>, <&p_clk>;
+			#clock-cells = <1>;
+			clock-indices = <
+				R8A7792_CLK_HSCIF1 R8A7792_CLK_HSCIF0
+				R8A7792_CLK_SCIF3 R8A7792_CLK_SCIF2
+				R8A7792_CLK_SCIF1 R8A7792_CLK_SCIF0
+			>;
+			clock-output-names = "hscif1", "hscif0", "scif3",
+					     "scif2", "scif1", "scif0";
+		};
+	};
+
+	/* External root clock */
+	extal_clk: extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board. */
+		clock-frequency = <0>;
+	};
+
+	/* External SCIF clock */
+	scif_clk: scif {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board. */
+		clock-frequency = <0>;
+	};
+};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 22/41] ARM: dts: r8a7792: initial SoC device tree

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

The initial R8A7792 SoC device tree including CPU cores, GIC, timer, SYSC,
and the required  clock descriptions.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 170 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 170 insertions(+)
 create mode 100644 arch/arm/boot/dts/r8a7792.dtsi

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
new file mode 100644
index 000000000000..33f2362a1f52
--- /dev/null
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -0,0 +1,170 @@
+/*
+ * Device Tree Source for the r8a7792 SoC
+ *
+ * Copyright (C) 2016 Cogent Embedded Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/clock/r8a7792-clock.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a7792-sysc.h>
+
+/ {
+	compatible = "renesas,r8a7792";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0>;
+			clock-frequency = <1000000000>;
+			clocks = <&cpg_clocks R8A7792_CLK_Z>;
+			power-domains = <&sysc R8A7792_PD_CA15_CPU0>;
+			next-level-cache = <&L2_CA15>;
+		};
+
+		L2_CA15: cache-controller at 0 {
+			compatible = "cache";
+			reg = <0>;
+			cache-unified;
+			cache-level = <2>;
+			power-domains = <&sysc R8A7792_PD_CA15_SCU>;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gic: interrupt-controller at f1001000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0 0xf1001000 0 0x1000>,
+			      <0 0xf1002000 0 0x1000>,
+			      <0 0xf1004000 0 0x2000>,
+			      <0 0xf1006000 0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		timer {
+			compatible = "arm,armv7-timer";
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
+				      IRQ_TYPE_LEVEL_LOW)>;
+		};
+
+		sysc: system-controller at e6180000 {
+			compatible = "renesas,r8a7792-sysc";
+			reg = <0 0xe6180000 0 0x0200>;
+			#power-domain-cells = <1>;
+		};
+
+		/* Special CPG clocks */
+		cpg_clocks: cpg_clocks at e6150000 {
+			compatible = "renesas,r8a7792-cpg-clocks",
+				     "renesas,rcar-gen2-cpg-clocks";
+			reg = <0 0xe6150000 0 0x1000>;
+			clocks = <&extal_clk>;
+			#clock-cells = <1>;
+			clock-output-names = "main", "pll0", "pll1", "pll3",
+					     "lb", "qspi", "z", "adsp";
+			#power-domain-cells = <0>;
+		};
+
+		/* Fixed factor clocks */
+		zs_clk: zs {
+			compatible = "fixed-factor-clock";
+			clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+			#clock-cells = <0>;
+			clock-div = <6>;
+			clock-mult = <1>;
+		};
+		p_clk: p {
+			compatible = "fixed-factor-clock";
+			clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+			#clock-cells = <0>;
+			clock-div = <24>;
+			clock-mult = <1>;
+		};
+		cp_clk: cp {
+			compatible = "fixed-factor-clock";
+			clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+			#clock-cells = <0>;
+			clock-div = <48>;
+			clock-mult = <1>;
+		};
+
+		/* Gate clocks */
+		mstp2_clks: mstp2_clks at e6150138 {
+			compatible = "renesas,r8a7792-mstp-clocks",
+				     "renesas,cpg-mstp-clocks";
+			reg = <0 0xe6150138 0 4>, <0 0xe6150040 0 4>;
+			clocks = <&zs_clk>, <&zs_clk>;
+			#clock-cells = <1>;
+			clock-indices = <
+				R8A7792_CLK_SYS_DMAC1 R8A7792_CLK_SYS_DMAC0
+			>;
+			clock-output-names = "sys-dmac1", "sys-dmac0";
+		};
+		mstp4_clks: mstp4_clks at e6150140 {
+			compatible = "renesas,r8a7792-mstp-clocks",
+				     "renesas,cpg-mstp-clocks";
+			reg = <0 0xe6150140 0 4>, <0 0xe615004c 0 4>;
+			clocks = <&cp_clk>;
+			#clock-cells = <1>;
+			clock-indices = <R8A7792_CLK_IRQC>;
+			clock-output-names = "irqc";
+		};
+		mstp7_clks: mstp7_clks at e615014c {
+			compatible = "renesas,r8a7792-mstp-clocks",
+				     "renesas,cpg-mstp-clocks";
+			reg = <0 0xe615014c 0 4>, <0 0xe61501c4 0 4>;
+			clocks = <&zs_clk>, <&zs_clk>, <&p_clk>, <&p_clk>,
+				 <&p_clk>, <&p_clk>;
+			#clock-cells = <1>;
+			clock-indices = <
+				R8A7792_CLK_HSCIF1 R8A7792_CLK_HSCIF0
+				R8A7792_CLK_SCIF3 R8A7792_CLK_SCIF2
+				R8A7792_CLK_SCIF1 R8A7792_CLK_SCIF0
+			>;
+			clock-output-names = "hscif1", "hscif0", "scif3",
+					     "scif2", "scif1", "scif0";
+		};
+	};
+
+	/* External root clock */
+	extal_clk: extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board. */
+		clock-frequency = <0>;
+	};
+
+	/* External SCIF clock */
+	scif_clk: scif {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board. */
+		clock-frequency = <0>;
+	};
+};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 23/41] ARM: dts: r8a7792: add SYS-DMAC support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Describe SYS-DMAC0/1 in the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 64 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 33f2362a1f52..6017ea5280a0 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -79,6 +79,70 @@
 			#power-domain-cells = <1>;
 		};
 
+		dmac0: dma-controller@e6700000 {
+			compatible = "renesas,dmac-r8a7792",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe6700000 0 0x20000>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14";
+			clocks = <&mstp2_clks R8A7792_CLK_SYS_DMAC0>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			#dma-cells = <1>;
+			dma-channels = <15>;
+		};
+
+		dmac1: dma-controller@e6720000 {
+			compatible = "renesas,dmac-r8a7792",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe6720000 0 0x20000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14";
+			clocks = <&mstp2_clks R8A7792_CLK_SYS_DMAC1>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			#dma-cells = <1>;
+			dma-channels = <15>;
+		};
+
 		/* Special CPG clocks */
 		cpg_clocks: cpg_clocks@e6150000 {
 			compatible = "renesas,r8a7792-cpg-clocks",
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 23/41] ARM: dts: r8a7792: add SYS-DMAC support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Describe SYS-DMAC0/1 in the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 64 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 33f2362a1f52..6017ea5280a0 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -79,6 +79,70 @@
 			#power-domain-cells = <1>;
 		};
 
+		dmac0: dma-controller at e6700000 {
+			compatible = "renesas,dmac-r8a7792",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe6700000 0 0x20000>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14";
+			clocks = <&mstp2_clks R8A7792_CLK_SYS_DMAC0>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			#dma-cells = <1>;
+			dma-channels = <15>;
+		};
+
+		dmac1: dma-controller at e6720000 {
+			compatible = "renesas,dmac-r8a7792",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe6720000 0 0x20000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14";
+			clocks = <&mstp2_clks R8A7792_CLK_SYS_DMAC1>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			#dma-cells = <1>;
+			dma-channels = <15>;
+		};
+
 		/* Special CPG clocks */
 		cpg_clocks: cpg_clocks at e6150000 {
 			compatible = "renesas,r8a7792-cpg-clocks",
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 24/41] ARM: dts: r8a7792: add [H]SCIF support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Describe [H]SCIFs in the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 90 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 90 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 6017ea5280a0..b6e34b431a51 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -143,6 +143,96 @@
 			dma-channels = <15>;
 		};
 
+		scif0: serial@e6e60000 {
+			compatible = "renesas,scif-r8a7792",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6e60000 0 64>;
+			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_SCIF0>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+			       <&dmac1 0x29>, <&dmac1 0x2a>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		scif1: serial@e6e68000 {
+			compatible = "renesas,scif-r8a7792",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6e68000 0 64>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_SCIF1>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+			       <&dmac1 0x2d>, <&dmac1 0x2e>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		scif2: serial@e6e58000 {
+			compatible = "renesas,scif-r8a7792",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6e58000 0 64>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_SCIF2>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+			       <&dmac1 0x2b>, <&dmac1 0x2c>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		scif3: serial@e6ea8000 {
+			compatible = "renesas,scif-r8a7792",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6ea8000 0 64>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_SCIF3>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x2f>, <&dmac0 0x30>,
+			       <&dmac1 0x2f>, <&dmac1 0x30>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		hscif0: serial@e62c0000 {
+			compatible = "renesas,hscif-r8a7792",
+				     "renesas,rcar-gen2-hscif", "renesas,hscif";
+			reg = <0 0xe62c0000 0 96>;
+			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_HSCIF0>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+			       <&dmac1 0x39>, <&dmac1 0x3a>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		hscif1: serial@e62c8000 {
+			compatible = "renesas,hscif-r8a7792",
+				     "renesas,rcar-gen2-hscif", "renesas,hscif";
+			reg = <0 0xe62c8000 0 96>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_HSCIF1>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+			       <&dmac1 0x4d>, <&dmac1 0x4e>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
 		/* Special CPG clocks */
 		cpg_clocks: cpg_clocks@e6150000 {
 			compatible = "renesas,r8a7792-cpg-clocks",
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 24/41] ARM: dts: r8a7792: add [H]SCIF support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Describe [H]SCIFs in the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 90 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 90 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 6017ea5280a0..b6e34b431a51 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -143,6 +143,96 @@
 			dma-channels = <15>;
 		};
 
+		scif0: serial at e6e60000 {
+			compatible = "renesas,scif-r8a7792",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6e60000 0 64>;
+			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_SCIF0>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+			       <&dmac1 0x29>, <&dmac1 0x2a>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		scif1: serial at e6e68000 {
+			compatible = "renesas,scif-r8a7792",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6e68000 0 64>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_SCIF1>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+			       <&dmac1 0x2d>, <&dmac1 0x2e>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		scif2: serial at e6e58000 {
+			compatible = "renesas,scif-r8a7792",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6e58000 0 64>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_SCIF2>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+			       <&dmac1 0x2b>, <&dmac1 0x2c>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		scif3: serial at e6ea8000 {
+			compatible = "renesas,scif-r8a7792",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6ea8000 0 64>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_SCIF3>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x2f>, <&dmac0 0x30>,
+			       <&dmac1 0x2f>, <&dmac1 0x30>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		hscif0: serial at e62c0000 {
+			compatible = "renesas,hscif-r8a7792",
+				     "renesas,rcar-gen2-hscif", "renesas,hscif";
+			reg = <0 0xe62c0000 0 96>;
+			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_HSCIF0>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+			       <&dmac1 0x39>, <&dmac1 0x3a>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		hscif1: serial at e62c8000 {
+			compatible = "renesas,hscif-r8a7792",
+				     "renesas,rcar-gen2-hscif", "renesas,hscif";
+			reg = <0 0xe62c8000 0 96>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp7_clks R8A7792_CLK_HSCIF1>, <&zs_clk>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+			       <&dmac1 0x4d>, <&dmac1 0x4e>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
 		/* Special CPG clocks */
 		cpg_clocks: cpg_clocks at e6150000 {
 			compatible = "renesas,r8a7792-cpg-clocks",
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 25/41] ARM: dts: r8a7792: add IRQC support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Describe the IRQC interrupt controller in the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index b6e34b431a51..18b4e50521c3 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -61,6 +61,19 @@
 				      IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		irqc: interrupt-controller@e61c0000 {
+			compatible = "renesas,irqc-r8a7792", "renesas,irqc";
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			reg = <0 0xe61c0000 0 0x200>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp4_clks R8A7792_CLK_IRQC>;
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+		};
+
 		timer {
 			compatible = "arm,armv7-timer";
 			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 25/41] ARM: dts: r8a7792: add IRQC support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Describe the IRQC interrupt controller in the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index b6e34b431a51..18b4e50521c3 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -61,6 +61,19 @@
 				      IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		irqc: interrupt-controller at e61c0000 {
+			compatible = "renesas,irqc-r8a7792", "renesas,irqc";
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			reg = <0 0xe61c0000 0 0x200>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp4_clks R8A7792_CLK_IRQC>;
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+		};
+
 		timer {
 			compatible = "arm,armv7-timer";
 			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 26/41] ARM: dts: blanche: document Blanche board

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Document the Blanche device tree bindings, listing it as a supported board.

This allows to use checkpatch.pl to validate .dts files referring to the
Blanche board.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 Documentation/devicetree/bindings/arm/shmobile.txt | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt
index 9cf67e48f222..6adb9d549fce 100644
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -39,6 +39,8 @@ Boards:
     compatible = "renesas,ape6evm", "renesas,r8a73a4"
   - Atmark Techno Armadillo-800 EVA
     compatible = "renesas,armadillo800eva"
+  - Blanche (RTP0RC7792SEB00010S)
+    compatible = "renesas,blanche", "renesas,r8a7792"
   - BOCK-W
     compatible = "renesas,bockw", "renesas,r8a7778"
   - Genmai (RTK772100BC00000BR)
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 26/41] ARM: dts: blanche: document Blanche board

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Document the Blanche device tree bindings, listing it as a supported board.

This allows to use checkpatch.pl to validate .dts files referring to the
Blanche board.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 Documentation/devicetree/bindings/arm/shmobile.txt | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt
index 9cf67e48f222..6adb9d549fce 100644
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -39,6 +39,8 @@ Boards:
     compatible = "renesas,ape6evm", "renesas,r8a73a4"
   - Atmark Techno Armadillo-800 EVA
     compatible = "renesas,armadillo800eva"
+  - Blanche (RTP0RC7792SEB00010S)
+    compatible = "renesas,blanche", "renesas,r8a7792"
   - BOCK-W
     compatible = "renesas,bockw", "renesas,r8a7778"
   - Genmai (RTK772100BC00000BR)
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 27/41] ARM: dts: blanche: initial device tree

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add the initial device  tree for the R8A7792 SoC based Blanche board.
The board has 2 debug serial ports: SCIF0 and SCIF3; include support for
them,  so that  the serial console  can  work.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/Makefile            |  1 +
 arch/arm/boot/dts/r8a7792-blanche.dts | 45 +++++++++++++++++++++++++++++++++++
 2 files changed, 46 insertions(+)
 create mode 100644 arch/arm/boot/dts/r8a7792-blanche.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 06b6c2d695bf..91630d1376bc 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -638,6 +638,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
 	r8a7790-lager.dtb \
 	r8a7791-koelsch.dtb \
 	r8a7791-porter.dtb \
+	r8a7792-blanche.dtb \
 	r8a7793-gose.dtb \
 	r8a7794-alt.dtb \
 	r8a7794-silk.dtb \
diff --git a/arch/arm/boot/dts/r8a7792-blanche.dts b/arch/arm/boot/dts/r8a7792-blanche.dts
new file mode 100644
index 000000000000..e277d924441b
--- /dev/null
+++ b/arch/arm/boot/dts/r8a7792-blanche.dts
@@ -0,0 +1,45 @@
+/*
+ * Device Tree Source for the Blanche board
+ *
+ * Copyright (C) 2014 Renesas Electronics Corporation
+ * Copyright (C) 2016 Cogent  Embedded, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "r8a7792.dtsi"
+
+/ {
+	model = "Blanche";
+	compatible = "renesas,blanche", "renesas,r8a7792";
+
+	aliases {
+		serial0 = &scif0;
+		serial1 = &scif3;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x40000000>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <20000000>;
+};
+
+&scif0 {
+	status = "okay";
+};
+
+&scif3 {
+	status = "okay";
+};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 27/41] ARM: dts: blanche: initial device tree

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add the initial device  tree for the R8A7792 SoC based Blanche board.
The board has 2 debug serial ports: SCIF0 and SCIF3; include support for
them,  so that  the serial console  can  work.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/Makefile            |  1 +
 arch/arm/boot/dts/r8a7792-blanche.dts | 45 +++++++++++++++++++++++++++++++++++
 2 files changed, 46 insertions(+)
 create mode 100644 arch/arm/boot/dts/r8a7792-blanche.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 06b6c2d695bf..91630d1376bc 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -638,6 +638,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
 	r8a7790-lager.dtb \
 	r8a7791-koelsch.dtb \
 	r8a7791-porter.dtb \
+	r8a7792-blanche.dtb \
 	r8a7793-gose.dtb \
 	r8a7794-alt.dtb \
 	r8a7794-silk.dtb \
diff --git a/arch/arm/boot/dts/r8a7792-blanche.dts b/arch/arm/boot/dts/r8a7792-blanche.dts
new file mode 100644
index 000000000000..e277d924441b
--- /dev/null
+++ b/arch/arm/boot/dts/r8a7792-blanche.dts
@@ -0,0 +1,45 @@
+/*
+ * Device Tree Source for the Blanche board
+ *
+ * Copyright (C) 2014 Renesas Electronics Corporation
+ * Copyright (C) 2016 Cogent  Embedded, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "r8a7792.dtsi"
+
+/ {
+	model = "Blanche";
+	compatible = "renesas,blanche", "renesas,r8a7792";
+
+	aliases {
+		serial0 = &scif0;
+		serial1 = &scif3;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory at 40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x40000000>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <20000000>;
+};
+
+&scif0 {
+	status = "okay";
+};
+
+&scif3 {
+	status = "okay";
+};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 28/41] ARM: dts: blanche: add Ethernet support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

R8A7792  SoC  doesn't have the EtherMAC core, so SMSC  LAN89218  Ethernet
chip was used instead on the Blanche board; this chip  is compatible with
SMSC LAN9115  for  which there's a (device tree aware) driver. Describe
the  chip in  the  Blanche device tree;  enable DHCP and NFS root in the
kernel command line for the kernel booting.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792-blanche.dts | 23 ++++++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7792-blanche.dts b/arch/arm/boot/dts/r8a7792-blanche.dts
index e277d924441b..e7b40f0e7da6 100644
--- a/arch/arm/boot/dts/r8a7792-blanche.dts
+++ b/arch/arm/boot/dts/r8a7792-blanche.dts
@@ -22,7 +22,7 @@
 	};
 
 	chosen {
-		bootargs = "ignore_loglevel";
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
 		stdout-path = "serial0:115200n8";
 	};
 
@@ -30,6 +30,27 @@
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	d3_3v: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "D3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	ethernet@18000000 {
+		compatible = "smsc,lan89218", "smsc,lan9115";
+		reg = <0 0x18000000 0 0x100>;
+		phy-mode = "mii";
+		interrupt-parent = <&irqc>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		smsc,irq-push-pull;
+		reg-io-width = <4>;
+		vddvario-supply = <&d3_3v>;
+		vdd33a-supply = <&d3_3v>;
+	};
 };
 
 &extal_clk {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 28/41] ARM: dts: blanche: add Ethernet support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

R8A7792  SoC  doesn't have the EtherMAC core, so SMSC  LAN89218  Ethernet
chip was used instead on the Blanche board; this chip  is compatible with
SMSC LAN9115  for  which there's a (device tree aware) driver. Describe
the  chip in  the  Blanche device tree;  enable DHCP and NFS root in the
kernel command line for the kernel booting.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792-blanche.dts | 23 ++++++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7792-blanche.dts b/arch/arm/boot/dts/r8a7792-blanche.dts
index e277d924441b..e7b40f0e7da6 100644
--- a/arch/arm/boot/dts/r8a7792-blanche.dts
+++ b/arch/arm/boot/dts/r8a7792-blanche.dts
@@ -22,7 +22,7 @@
 	};
 
 	chosen {
-		bootargs = "ignore_loglevel";
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
 		stdout-path = "serial0:115200n8";
 	};
 
@@ -30,6 +30,27 @@
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	d3_3v: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "D3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	ethernet at 18000000 {
+		compatible = "smsc,lan89218", "smsc,lan9115";
+		reg = <0 0x18000000 0 0x100>;
+		phy-mode = "mii";
+		interrupt-parent = <&irqc>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		smsc,irq-push-pull;
+		reg-io-width = <4>;
+		vddvario-supply = <&d3_3v>;
+		vdd33a-supply = <&d3_3v>;
+	};
 };
 
 &extal_clk {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 29/41] ARM: dts: silk: add DU pins

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add the (previously omitted) DU pin data to the SILK board's device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-silk.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index 488de730bee8..cf24f45fff22 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -183,6 +183,16 @@
 		groups = "usb1";
 		function = "usb1";
 	};
+
+	du0_pins: du0 {
+		groups = "du0_rgb888", "du0_sync", "du0_disp", "du0_clk0_out";
+		function = "du0";
+	};
+
+	du1_pins: du1 {
+		groups = "du1_rgb666", "du1_sync", "du1_disp", "du1_clk0_out";
+		function = "du1";
+	};
 };
 
 &scif2 {
@@ -360,6 +370,8 @@
 };
 
 &du {
+	pinctrl-0 = <&du0_pins &du1_pins>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	clocks = <&mstp7_clks R8A7794_CLK_DU0>,
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 29/41] ARM: dts: silk: add DU pins

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add the (previously omitted) DU pin data to the SILK board's device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794-silk.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index 488de730bee8..cf24f45fff22 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -183,6 +183,16 @@
 		groups = "usb1";
 		function = "usb1";
 	};
+
+	du0_pins: du0 {
+		groups = "du0_rgb888", "du0_sync", "du0_disp", "du0_clk0_out";
+		function = "du0";
+	};
+
+	du1_pins: du1 {
+		groups = "du1_rgb666", "du1_sync", "du1_disp", "du1_clk0_out";
+		function = "du1";
+	};
 };
 
 &scif2 {
@@ -360,6 +370,8 @@
 };
 
 &du {
+	pinctrl-0 = <&du0_pins &du1_pins>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	clocks = <&mstp7_clks R8A7794_CLK_DU0>,
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 30/41] ARM: dts: r8a7792: add JPU clocks

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add JPU clock and its parent, M2 clock to the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi            | 16 ++++++++++++++++
 include/dt-bindings/clock/r8a7792-clock.h |  1 +
 2 files changed, 17 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 18b4e50521c3..7077c5db2678 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -280,8 +280,24 @@
 			clock-div = <48>;
 			clock-mult = <1>;
 		};
+		m2_clk: m2 {
+			compatible = "fixed-factor-clock";
+			clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+			#clock-cells = <0>;
+			clock-div = <8>;
+			clock-mult = <1>;
+		};
 
 		/* Gate clocks */
+		mstp1_clks: mstp1_clks@e6150134 {
+			compatible = "renesas,r8a7792-mstp-clocks",
+				     "renesas,cpg-mstp-clocks";
+			reg = <0 0xe6150134 0 4>, <0 0xe6150038 0 4>;
+			clocks = <&m2_clk>;
+			#clock-cells = <1>;
+			clock-indices = <R8A7792_CLK_JPU>;
+			clock-output-names = "jpu";
+		};
 		mstp2_clks: mstp2_clks@e6150138 {
 			compatible = "renesas,r8a7792-mstp-clocks",
 				     "renesas,cpg-mstp-clocks";
diff --git a/include/dt-bindings/clock/r8a7792-clock.h b/include/dt-bindings/clock/r8a7792-clock.h
index 949801eb0652..89a5155913f6 100644
--- a/include/dt-bindings/clock/r8a7792-clock.h
+++ b/include/dt-bindings/clock/r8a7792-clock.h
@@ -24,6 +24,7 @@
 #define R8A7792_CLK_MSIOF0		0
 
 /* MSTP1 */
+#define R8A7792_CLK_JPU			6
 #define R8A7792_CLK_TMU1		11
 #define R8A7792_CLK_TMU3		21
 #define R8A7792_CLK_TMU2		22
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 30/41] ARM: dts: r8a7792: add JPU clocks

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add JPU clock and its parent, M2 clock to the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi            | 16 ++++++++++++++++
 include/dt-bindings/clock/r8a7792-clock.h |  1 +
 2 files changed, 17 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 18b4e50521c3..7077c5db2678 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -280,8 +280,24 @@
 			clock-div = <48>;
 			clock-mult = <1>;
 		};
+		m2_clk: m2 {
+			compatible = "fixed-factor-clock";
+			clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+			#clock-cells = <0>;
+			clock-div = <8>;
+			clock-mult = <1>;
+		};
 
 		/* Gate clocks */
+		mstp1_clks: mstp1_clks at e6150134 {
+			compatible = "renesas,r8a7792-mstp-clocks",
+				     "renesas,cpg-mstp-clocks";
+			reg = <0 0xe6150134 0 4>, <0 0xe6150038 0 4>;
+			clocks = <&m2_clk>;
+			#clock-cells = <1>;
+			clock-indices = <R8A7792_CLK_JPU>;
+			clock-output-names = "jpu";
+		};
 		mstp2_clks: mstp2_clks at e6150138 {
 			compatible = "renesas,r8a7792-mstp-clocks",
 				     "renesas,cpg-mstp-clocks";
diff --git a/include/dt-bindings/clock/r8a7792-clock.h b/include/dt-bindings/clock/r8a7792-clock.h
index 949801eb0652..89a5155913f6 100644
--- a/include/dt-bindings/clock/r8a7792-clock.h
+++ b/include/dt-bindings/clock/r8a7792-clock.h
@@ -24,6 +24,7 @@
 #define R8A7792_CLK_MSIOF0		0
 
 /* MSTP1 */
+#define R8A7792_CLK_JPU			6
 #define R8A7792_CLK_TMU1		11
 #define R8A7792_CLK_TMU3		21
 #define R8A7792_CLK_TMU2		22
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 31/41] ARM: dts: r8a7792: add JPU support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Describe JPEG Processing Unit (JPU) in the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 7077c5db2678..ad895f8b2353 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -246,6 +246,15 @@
 			status = "disabled";
 		};
 
+		jpu: jpeg-codec@fe980000 {
+			compatible = "renesas,jpu-r8a7792",
+				     "renesas,rcar-gen2-jpu";
+			reg = <0 0xfe980000 0 0x10300>;
+			interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp1_clks R8A7792_CLK_JPU>;
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+		};
+
 		/* Special CPG clocks */
 		cpg_clocks: cpg_clocks@e6150000 {
 			compatible = "renesas,r8a7792-cpg-clocks",
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 31/41] ARM: dts: r8a7792: add JPU support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Describe JPEG Processing Unit (JPU) in the R8A7792 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 7077c5db2678..ad895f8b2353 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -246,6 +246,15 @@
 			status = "disabled";
 		};
 
+		jpu: jpeg-codec at fe980000 {
+			compatible = "renesas,jpu-r8a7792",
+				     "renesas,rcar-gen2-jpu";
+			reg = <0 0xfe980000 0 0x10300>;
+			interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mstp1_clks R8A7792_CLK_JPU>;
+			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+		};
+
 		/* Special CPG clocks */
 		cpg_clocks: cpg_clocks at e6150000 {
 			compatible = "renesas,r8a7792-cpg-clocks",
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 32/41] ARM: dts: armadillo800eva: Update console parameters

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC1 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7740-armadillo800eva.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
index 6866f61a350c..7885075428bb 100644
--- a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
+++ b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
@@ -20,12 +20,12 @@
 	compatible = "renesas,armadillo800eva", "renesas,r8a7740";
 
 	aliases {
-		serial1 = &scifa1;
+		serial0 = &scifa1;
 	};
 
 	chosen {
-		bootargs = "console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp rw";
-		stdout-path = &scifa1;
+		bootargs = "earlyprintk ignore_loglevel root=/dev/nfs ip=dhcp rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory@40000000 {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 32/41] ARM: dts: armadillo800eva: Update console parameters

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC1 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7740-armadillo800eva.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
index 6866f61a350c..7885075428bb 100644
--- a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
+++ b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
@@ -20,12 +20,12 @@
 	compatible = "renesas,armadillo800eva", "renesas,r8a7740";
 
 	aliases {
-		serial1 = &scifa1;
+		serial0 = &scifa1;
 	};
 
 	chosen {
-		bootargs = "console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp rw";
-		stdout-path = &scifa1;
+		bootargs = "earlyprintk ignore_loglevel root=/dev/nfs ip=dhcp rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory at 40000000 {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 33/41] ARM: dts: genmai: Update console parameters

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC2 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r7s72100-genmai.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r7s72100-genmai.dts b/arch/arm/boot/dts/r7s72100-genmai.dts
index 05ba9953b4d8..118a8e2b86bd 100644
--- a/arch/arm/boot/dts/r7s72100-genmai.dts
+++ b/arch/arm/boot/dts/r7s72100-genmai.dts
@@ -17,12 +17,12 @@
 	compatible = "renesas,genmai", "renesas,r7s72100";
 
 	aliases {
-		serial2 = &scif2;
+		serial0 = &scif2;
 	};
 
 	chosen {
 		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
-		stdout-path = &scif2;
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory@8000000 {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 33/41] ARM: dts: genmai: Update console parameters

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC2 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r7s72100-genmai.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r7s72100-genmai.dts b/arch/arm/boot/dts/r7s72100-genmai.dts
index 05ba9953b4d8..118a8e2b86bd 100644
--- a/arch/arm/boot/dts/r7s72100-genmai.dts
+++ b/arch/arm/boot/dts/r7s72100-genmai.dts
@@ -17,12 +17,12 @@
 	compatible = "renesas,genmai", "renesas,r7s72100";
 
 	aliases {
-		serial2 = &scif2;
+		serial0 = &scif2;
 	};
 
 	chosen {
 		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
-		stdout-path = &scif2;
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory at 8000000 {
-- 
2.7.0.rc3.207.g0ac5344

[GIT PULL] Second Round of Renesas ARM Based SoC DT Updates for v4.8

[Simon Horman]

Hi Olof, Hi Kevin, Hi Arnd,

Please consider these second round of Renesas ARM based SoC DT updates for v4.8.

This pull request is based on the previous round of
such requests, tagged as renesas-dt-for-v4.8,
which you have already pulled.


The following changes since commit b6960f19676e19f37a5e5a8af059fdf3b435d2f4:

  ARM: dts: silk: Fix W=1 dtc warnings (2016-05-30 09:37:13 +0900)

are available in the git repository at:

  git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-dt2-for-v4.8

for you to fetch changes up to 8fd763c75c3ab8e72e5d7f0d4c53531e6ff76197:

  ARM: dts: r8a7792: add SMP support (2016-06-30 14:26:14 +0200)

----------------------------------------------------------------
Second Round of Renesas ARM Based SoC DT Updates for v4.8

* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
  serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name

----------------------------------------------------------------
Geert Uytterhoeven (24):
      ARM: dts: ape6evm: Name serial port pfc subnode after device name
      ARM: dts: ape6evm: Name mmc pfc subnode after device name
      ARM: dts: armadillo800eva: Name serial port pfc subnode after device name
      ARM: dts: bockw: Name serial port pfc subnode after device name
      ARM: dts: marzen: Name serial port pfc subnodes after device names
      ARM: dts: lager: Name serial port pfc subnodes after device names
      ARM: dts: lager: Name spi pfc subnodes after device names
      ARM: dts: lager: Name vin pfc subnode after device name
      ARM: dts: koelsch: Name serial port pfc subnodes after device names
      ARM: dts: koelsch: Name spi pfc subnodes after device names
      ARM: dts: porter: Name serial port pfc subnode after device name
      ARM: dts: porter: Name spi pfc subnode after device name
      ARM: dts: gose: Name serial port pfc subnodes after device names
      ARM: dts: gose: Name spi pfc subnode after device name
      ARM: dts: alt: Name serial port pfc subnode after device name
      ARM: dts: alt: Name spi pfc subnode after device name
      ARM: dts: silk: Name serial port pfc subnode after device name
      ARM: dts: silk: Name spi pfc subnode after device name
      ARM: dts: kzm9g: Name serial port pfc subnode after device name
      ARM: dts: armadillo800eva: Update console parameters
      ARM: dts: genmai: Update console parameters
      ARM: dts: marzen: Add serial port config to chosen/stdout-path
      ARM: dts: kzm9d: Update console parameters
      ARM: dts: kzm9g: Update console parameters

Magnus Damm (4):
      devicetree: bindings: Renesas APMU and SMP Enable method
      ARM: dts: r8a7790: Add APMU nodes
      ARM: dts: r8a7791: Add APMU node
      ARM: dts: r8a7793: Add APMU node and second CPU core

Sergei Shtylyov (13):
      ARM: dts: r8a7792: add clock index macros
      ARM: dts: r8a7792: add power domain index macros
      ARM: dts: r8a7792: initial SoC device tree
      ARM: dts: r8a7792: add SYS-DMAC support
      ARM: dts: r8a7792: add [H]SCIF support
      ARM: dts: r8a7792: add IRQC support
      ARM: dts: blanche: document Blanche board
      ARM: dts: blanche: initial device tree
      ARM: dts: blanche: add Ethernet support
      ARM: dts: silk: add DU pins
      ARM: dts: r8a7792: add JPU clocks
      ARM: dts: r8a7792: add JPU support
      ARM: dts: r8a7792: add SMP support

 Documentation/devicetree/bindings/arm/cpus.txt     |   1 +
 Documentation/devicetree/bindings/arm/shmobile.txt |   2 +
 .../devicetree/bindings/power/renesas,apmu.txt     |  31 ++
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/emev2-kzm9d.dts                  |   8 +-
 arch/arm/boot/dts/r7s72100-genmai.dts              |   4 +-
 arch/arm/boot/dts/r8a73a4-ape6evm.dts              |   4 +-
 arch/arm/boot/dts/r8a7740-armadillo800eva.dts      |   8 +-
 arch/arm/boot/dts/r8a7778-bockw.dts                |   2 +-
 arch/arm/boot/dts/r8a7779-marzen.dts               |   6 +-
 arch/arm/boot/dts/r8a7790-lager.dts                |  10 +-
 arch/arm/boot/dts/r8a7790.dtsi                     |  13 +
 arch/arm/boot/dts/r8a7791-koelsch.dts              |   8 +-
 arch/arm/boot/dts/r8a7791-porter.dts               |   4 +-
 arch/arm/boot/dts/r8a7791.dtsi                     |   7 +
 arch/arm/boot/dts/r8a7792-blanche.dts              |  66 ++++
 arch/arm/boot/dts/r8a7792.dtsi                     | 378 +++++++++++++++++++++
 arch/arm/boot/dts/r8a7793-gose.dts                 |   6 +-
 arch/arm/boot/dts/r8a7793.dtsi                     |  15 +
 arch/arm/boot/dts/r8a7794-alt.dts                  |   4 +-
 arch/arm/boot/dts/r8a7794-silk.dts                 |  16 +-
 arch/arm/boot/dts/sh73a0-kzm9g.dts                 |   8 +-
 include/dt-bindings/clock/r8a7792-clock.h          | 103 ++++++
 include/dt-bindings/power/r8a7792-sysc.h           |  26 ++
 24 files changed, 695 insertions(+), 36 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power/renesas,apmu.txt
 create mode 100644 arch/arm/boot/dts/r8a7792-blanche.dts
 create mode 100644 arch/arm/boot/dts/r8a7792.dtsi
 create mode 100644 include/dt-bindings/clock/r8a7792-clock.h
 create mode 100644 include/dt-bindings/power/r8a7792-sysc.h

[PATCH 34/41] ARM: dts: marzen: Add serial port config to chosen/stdout-path

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7779-marzen.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7779-marzen.dts b/arch/arm/boot/dts/r8a7779-marzen.dts
index 013e6f510b0f..541678df90a9 100644
--- a/arch/arm/boot/dts/r8a7779-marzen.dts
+++ b/arch/arm/boot/dts/r8a7779-marzen.dts
@@ -25,7 +25,7 @@
 
 	chosen {
 		bootargs = "ignore_loglevel root=/dev/nfs ip=on";
-		stdout-path = &scif2;
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory@60000000 {
-- 
2.7.0.rc3.207.g0ac5344

[GIT PULL] Second Round of Renesas ARM Based SoC DT Updates for v4.8

[Simon Horman]

Hi Olof, Hi Kevin, Hi Arnd,

Please consider these second round of Renesas ARM based SoC DT updates for v4.8.

This pull request is based on the previous round of
such requests, tagged as renesas-dt-for-v4.8,
which you have already pulled.


The following changes since commit b6960f19676e19f37a5e5a8af059fdf3b435d2f4:

  ARM: dts: silk: Fix W=1 dtc warnings (2016-05-30 09:37:13 +0900)

are available in the git repository at:

  git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-dt2-for-v4.8

for you to fetch changes up to 8fd763c75c3ab8e72e5d7f0d4c53531e6ff76197:

  ARM: dts: r8a7792: add SMP support (2016-06-30 14:26:14 +0200)

----------------------------------------------------------------
Second Round of Renesas ARM Based SoC DT Updates for v4.8

* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
  serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name

----------------------------------------------------------------
Geert Uytterhoeven (24):
      ARM: dts: ape6evm: Name serial port pfc subnode after device name
      ARM: dts: ape6evm: Name mmc pfc subnode after device name
      ARM: dts: armadillo800eva: Name serial port pfc subnode after device name
      ARM: dts: bockw: Name serial port pfc subnode after device name
      ARM: dts: marzen: Name serial port pfc subnodes after device names
      ARM: dts: lager: Name serial port pfc subnodes after device names
      ARM: dts: lager: Name spi pfc subnodes after device names
      ARM: dts: lager: Name vin pfc subnode after device name
      ARM: dts: koelsch: Name serial port pfc subnodes after device names
      ARM: dts: koelsch: Name spi pfc subnodes after device names
      ARM: dts: porter: Name serial port pfc subnode after device name
      ARM: dts: porter: Name spi pfc subnode after device name
      ARM: dts: gose: Name serial port pfc subnodes after device names
      ARM: dts: gose: Name spi pfc subnode after device name
      ARM: dts: alt: Name serial port pfc subnode after device name
      ARM: dts: alt: Name spi pfc subnode after device name
      ARM: dts: silk: Name serial port pfc subnode after device name
      ARM: dts: silk: Name spi pfc subnode after device name
      ARM: dts: kzm9g: Name serial port pfc subnode after device name
      ARM: dts: armadillo800eva: Update console parameters
      ARM: dts: genmai: Update console parameters
      ARM: dts: marzen: Add serial port config to chosen/stdout-path
      ARM: dts: kzm9d: Update console parameters
      ARM: dts: kzm9g: Update console parameters

Magnus Damm (4):
      devicetree: bindings: Renesas APMU and SMP Enable method
      ARM: dts: r8a7790: Add APMU nodes
      ARM: dts: r8a7791: Add APMU node
      ARM: dts: r8a7793: Add APMU node and second CPU core

Sergei Shtylyov (13):
      ARM: dts: r8a7792: add clock index macros
      ARM: dts: r8a7792: add power domain index macros
      ARM: dts: r8a7792: initial SoC device tree
      ARM: dts: r8a7792: add SYS-DMAC support
      ARM: dts: r8a7792: add [H]SCIF support
      ARM: dts: r8a7792: add IRQC support
      ARM: dts: blanche: document Blanche board
      ARM: dts: blanche: initial device tree
      ARM: dts: blanche: add Ethernet support
      ARM: dts: silk: add DU pins
      ARM: dts: r8a7792: add JPU clocks
      ARM: dts: r8a7792: add JPU support
      ARM: dts: r8a7792: add SMP support

 Documentation/devicetree/bindings/arm/cpus.txt     |   1 +
 Documentation/devicetree/bindings/arm/shmobile.txt |   2 +
 .../devicetree/bindings/power/renesas,apmu.txt     |  31 ++
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/emev2-kzm9d.dts                  |   8 +-
 arch/arm/boot/dts/r7s72100-genmai.dts              |   4 +-
 arch/arm/boot/dts/r8a73a4-ape6evm.dts              |   4 +-
 arch/arm/boot/dts/r8a7740-armadillo800eva.dts      |   8 +-
 arch/arm/boot/dts/r8a7778-bockw.dts                |   2 +-
 arch/arm/boot/dts/r8a7779-marzen.dts               |   6 +-
 arch/arm/boot/dts/r8a7790-lager.dts                |  10 +-
 arch/arm/boot/dts/r8a7790.dtsi                     |  13 +
 arch/arm/boot/dts/r8a7791-koelsch.dts              |   8 +-
 arch/arm/boot/dts/r8a7791-porter.dts               |   4 +-
 arch/arm/boot/dts/r8a7791.dtsi                     |   7 +
 arch/arm/boot/dts/r8a7792-blanche.dts              |  66 ++++
 arch/arm/boot/dts/r8a7792.dtsi                     | 378 +++++++++++++++++++++
 arch/arm/boot/dts/r8a7793-gose.dts                 |   6 +-
 arch/arm/boot/dts/r8a7793.dtsi                     |  15 +
 arch/arm/boot/dts/r8a7794-alt.dts                  |   4 +-
 arch/arm/boot/dts/r8a7794-silk.dts                 |  16 +-
 arch/arm/boot/dts/sh73a0-kzm9g.dts                 |   8 +-
 include/dt-bindings/clock/r8a7792-clock.h          | 103 ++++++
 include/dt-bindings/power/r8a7792-sysc.h           |  26 ++
 24 files changed, 695 insertions(+), 36 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power/renesas,apmu.txt
 create mode 100644 arch/arm/boot/dts/r8a7792-blanche.dts
 create mode 100644 arch/arm/boot/dts/r8a7792.dtsi
 create mode 100644 include/dt-bindings/clock/r8a7792-clock.h
 create mode 100644 include/dt-bindings/power/r8a7792-sysc.h

[PATCH 34/41] ARM: dts: marzen: Add serial port config to chosen/stdout-path

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7779-marzen.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r8a7779-marzen.dts b/arch/arm/boot/dts/r8a7779-marzen.dts
index 013e6f510b0f..541678df90a9 100644
--- a/arch/arm/boot/dts/r8a7779-marzen.dts
+++ b/arch/arm/boot/dts/r8a7779-marzen.dts
@@ -25,7 +25,7 @@
 
 	chosen {
 		bootargs = "ignore_loglevel root=/dev/nfs ip=on";
-		stdout-path = &scif2;
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory at 60000000 {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 35/41] ARM: dts: kzm9d: Update console parameters

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Add a "serial1" alias for the serial console (it is labeled "uart1").
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameter from the kernel command line, as it's no
longer needed for DT-based platforms.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/emev2-kzm9d.dts | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/emev2-kzm9d.dts b/arch/arm/boot/dts/emev2-kzm9d.dts
index 9eb86f8f32c5..60d0a732833a 100644
--- a/arch/arm/boot/dts/emev2-kzm9d.dts
+++ b/arch/arm/boot/dts/emev2-kzm9d.dts
@@ -23,9 +23,13 @@
 		reg = <0x40000000 0x8000000>;
 	};
 
+	aliases {
+		serial1 = &uart1;
+	};
+
 	chosen {
-		bootargs = "console=ttyS1,115200n81 ignore_loglevel root=/dev/nfs ip=dhcp";
-		stdout-path = &uart1;
+		bootargs = "ignore_loglevel root=/dev/nfs ip=dhcp";
+		stdout-path = "serial1:115200n8";
 	};
 
 	gpio_keys {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 35/41] ARM: dts: kzm9d: Update console parameters

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Add a "serial1" alias for the serial console (it is labeled "uart1").
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameter from the kernel command line, as it's no
longer needed for DT-based platforms.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/emev2-kzm9d.dts | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/emev2-kzm9d.dts b/arch/arm/boot/dts/emev2-kzm9d.dts
index 9eb86f8f32c5..60d0a732833a 100644
--- a/arch/arm/boot/dts/emev2-kzm9d.dts
+++ b/arch/arm/boot/dts/emev2-kzm9d.dts
@@ -23,9 +23,13 @@
 		reg = <0x40000000 0x8000000>;
 	};
 
+	aliases {
+		serial1 = &uart1;
+	};
+
 	chosen {
-		bootargs = "console=ttyS1,115200n81 ignore_loglevel root=/dev/nfs ip=dhcp";
-		stdout-path = &uart1;
+		bootargs = "ignore_loglevel root=/dev/nfs ip=dhcp";
+		stdout-path = "serial1:115200n8";
 	};
 
 	gpio_keys {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 36/41] ARM: dts: kzm9g: Update console parameters

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC4 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/sh73a0-kzm9g.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts
index 1df68b167033..3d65f1f6d78b 100644
--- a/arch/arm/boot/dts/sh73a0-kzm9g.dts
+++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts
@@ -22,7 +22,7 @@
 	compatible = "renesas,kzm9g", "renesas,sh73a0";
 
 	aliases {
-		serial4 = &scifa4;
+		serial0 = &scifa4;
 	};
 
 	cpus {
@@ -39,8 +39,8 @@
 	};
 
 	chosen {
-		bootargs = "console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel rw";
-		stdout-path = &scifa4;
+		bootargs = "root=/dev/nfs ip=dhcp ignore_loglevel rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory@40000000 {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 36/41] ARM: dts: kzm9g: Update console parameters

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC4 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/sh73a0-kzm9g.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts
index 1df68b167033..3d65f1f6d78b 100644
--- a/arch/arm/boot/dts/sh73a0-kzm9g.dts
+++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts
@@ -22,7 +22,7 @@
 	compatible = "renesas,kzm9g", "renesas,sh73a0";
 
 	aliases {
-		serial4 = &scifa4;
+		serial0 = &scifa4;
 	};
 
 	cpus {
@@ -39,8 +39,8 @@
 	};
 
 	chosen {
-		bootargs = "console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel rw";
-		stdout-path = &scifa4;
+		bootargs = "root=/dev/nfs ip=dhcp ignore_loglevel rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory at 40000000 {
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 37/41] devicetree: bindings: Renesas APMU and SMP Enable method

[Simon Horman]

From: Magnus Damm <damm+renesas@opensource.se>

Add DT binding documentation for the APMU hardware and add "renesas,apmu"
to the list of enable methods for the ARM cpus.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 Documentation/devicetree/bindings/arm/cpus.txt     |  1 +
 .../devicetree/bindings/power/renesas,apmu.txt     | 31 ++++++++++++++++++++++
 2 files changed, 32 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/power/renesas,apmu.txt

diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index 3f0cbbb8395f..fa7520eb6387 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -204,6 +204,7 @@ nodes to be present and contain the properties described below.
 			    "qcom,gcc-msm8660"
 			    "qcom,kpss-acc-v1"
 			    "qcom,kpss-acc-v2"
+			    "renesas,apmu"
 			    "rockchip,rk3036-smp"
 			    "rockchip,rk3066-smp"
 			    "ste,dbx500-smp"
diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt
new file mode 100644
index 000000000000..84404c9edff7
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt
@@ -0,0 +1,31 @@
+DT bindings for the Renesas Advanced Power Management Unit
+
+Renesas R-Car line of SoCs utilize one or more APMU hardware units
+for CPU core power domain control including SMP boot and CPU Hotplug.
+
+Required properties:
+
+- compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback.
+	      Examples with soctypes are:
+		- "renesas,r8a7790-apmu" (R-Car H2)
+		- "renesas,r8a7791-apmu" (R-Car M2-W)
+		- "renesas,r8a7792-apmu" (R-Car V2H)
+		- "renesas,r8a7793-apmu" (R-Car M2-N)
+		- "renesas,r8a7794-apmu" (R-Car E2)
+
+- reg: Base address and length of the I/O registers used by the APMU.
+
+- cpus: This node contains a list of CPU cores, which should match the order
+  of CPU cores used by the WUPCR and PSTR registers in the Advanced Power
+  Management Unit section of the device's datasheet.
+
+
+Example:
+
+This shows the r8a7791 APMU that can control CPU0 and CPU1.
+
+	apmu@e6152000 {
+		compatible = "renesas,r8a7791-apmu", "renesas,apmu";
+		reg = <0 0xe6152000 0 0x188>;
+		cpus = <&cpu0 &cpu1>;
+	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 37/41] devicetree: bindings: Renesas APMU and SMP Enable method

[Simon Horman]

From: Magnus Damm <damm+renesas@opensource.se>

Add DT binding documentation for the APMU hardware and add "renesas,apmu"
to the list of enable methods for the ARM cpus.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Cc: devicetree at vger.kernel.org
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 Documentation/devicetree/bindings/arm/cpus.txt     |  1 +
 .../devicetree/bindings/power/renesas,apmu.txt     | 31 ++++++++++++++++++++++
 2 files changed, 32 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/power/renesas,apmu.txt

diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index 3f0cbbb8395f..fa7520eb6387 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -204,6 +204,7 @@ nodes to be present and contain the properties described below.
 			    "qcom,gcc-msm8660"
 			    "qcom,kpss-acc-v1"
 			    "qcom,kpss-acc-v2"
+			    "renesas,apmu"
 			    "rockchip,rk3036-smp"
 			    "rockchip,rk3066-smp"
 			    "ste,dbx500-smp"
diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt
new file mode 100644
index 000000000000..84404c9edff7
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt
@@ -0,0 +1,31 @@
+DT bindings for the Renesas Advanced Power Management Unit
+
+Renesas R-Car line of SoCs utilize one or more APMU hardware units
+for CPU core power domain control including SMP boot and CPU Hotplug.
+
+Required properties:
+
+- compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback.
+	      Examples with soctypes are:
+		- "renesas,r8a7790-apmu" (R-Car H2)
+		- "renesas,r8a7791-apmu" (R-Car M2-W)
+		- "renesas,r8a7792-apmu" (R-Car V2H)
+		- "renesas,r8a7793-apmu" (R-Car M2-N)
+		- "renesas,r8a7794-apmu" (R-Car E2)
+
+- reg: Base address and length of the I/O registers used by the APMU.
+
+- cpus: This node contains a list of CPU cores, which should match the order
+  of CPU cores used by the WUPCR and PSTR registers in the Advanced Power
+  Management Unit section of the device's datasheet.
+
+
+Example:
+
+This shows the r8a7791 APMU that can control CPU0 and CPU1.
+
+	apmu at e6152000 {
+		compatible = "renesas,r8a7791-apmu", "renesas,apmu";
+		reg = <0 0xe6152000 0 0x188>;
+		cpus = <&cpu0 &cpu1>;
+	};
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 38/41] ARM: dts: r8a7790: Add APMU nodes

[Simon Horman]

From: Magnus Damm <damm+renesas@opensource.se>

Add DT nodes for the Advanced Power Management Units (APMU), and use the
enable-method to point out that the APMU should be used for SMP
support.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790.dtsi | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 9997e7dfabe2..d18558f21102 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -44,6 +44,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -164,6 +165,18 @@
 		};
 	};
 
+	apmu@e6151000 {
+		compatible = "renesas,r8a7790-apmu", "renesas,apmu";
+		reg = <0 0xe6151000 0 0x188>;
+		cpus = <&cpu4 &cpu5 &cpu6 &cpu7>;
+	};
+
+	apmu@e6152000 {
+		compatible = "renesas,r8a7790-apmu", "renesas,apmu";
+		reg = <0 0xe6152000 0 0x188>;
+		cpus = <&cpu0 &cpu1 &cpu2 &cpu3>;
+	};
+
 	gic: interrupt-controller@f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 38/41] ARM: dts: r8a7790: Add APMU nodes

[Simon Horman]

From: Magnus Damm <damm+renesas@opensource.se>

Add DT nodes for the Advanced Power Management Units (APMU), and use the
enable-method to point out that the APMU should be used for SMP
support.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790.dtsi | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 9997e7dfabe2..d18558f21102 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -44,6 +44,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "renesas,apmu";
 
 		cpu0: cpu at 0 {
 			device_type = "cpu";
@@ -164,6 +165,18 @@
 		};
 	};
 
+	apmu at e6151000 {
+		compatible = "renesas,r8a7790-apmu", "renesas,apmu";
+		reg = <0 0xe6151000 0 0x188>;
+		cpus = <&cpu4 &cpu5 &cpu6 &cpu7>;
+	};
+
+	apmu at e6152000 {
+		compatible = "renesas,r8a7790-apmu", "renesas,apmu";
+		reg = <0 0xe6152000 0 0x188>;
+		cpus = <&cpu0 &cpu1 &cpu2 &cpu3>;
+	};
+
 	gic: interrupt-controller at f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 39/41] ARM: dts: r8a7791: Add APMU node

[Simon Horman]

From: Magnus Damm <damm+renesas@opensource.se>

Add a DT node for the Advanced Power Management Units (APMU), and use
the enable-method to point out that the APMU should be used for SMP
support.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 1985bd0dc32c..8f0086bbd96b 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -43,6 +43,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -101,6 +102,12 @@
 		};
 	};
 
+	apmu@e6152000 {
+		compatible = "renesas,r8a7791-apmu", "renesas,apmu";
+		reg = <0 0xe6152000 0 0x188>;
+		cpus = <&cpu0 &cpu1>;
+	};
+
 	gic: interrupt-controller@f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 39/41] ARM: dts: r8a7791: Add APMU node

[Simon Horman]

From: Magnus Damm <damm+renesas@opensource.se>

Add a DT node for the Advanced Power Management Units (APMU), and use
the enable-method to point out that the APMU should be used for SMP
support.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 1985bd0dc32c..8f0086bbd96b 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -43,6 +43,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "renesas,apmu";
 
 		cpu0: cpu at 0 {
 			device_type = "cpu";
@@ -101,6 +102,12 @@
 		};
 	};
 
+	apmu at e6152000 {
+		compatible = "renesas,r8a7791-apmu", "renesas,apmu";
+		reg = <0 0xe6152000 0 0x188>;
+		cpus = <&cpu0 &cpu1>;
+	};
+
 	gic: interrupt-controller at f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 40/41] ARM: dts: r8a7793: Add APMU node and second CPU core

[Simon Horman]

From: Magnus Damm <damm+renesas@opensource.se>

Add DT nodes for the Advanced Power Management Unit (APMU) and the
second CPU core.  Use the enable-method to point out that the APMU
should be used for SMP support.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7793.dtsi | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 9b55c1c6ee31..8d02aacf2892 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -35,6 +35,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -56,6 +57,14 @@
 			next-level-cache = <&L2_CA15>;
 		};
 
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+			clock-frequency = <1500000000>;
+			power-domains = <&sysc R8A7793_PD_CA15_CPU1>;
+		};
+
 		L2_CA15: cache-controller@0 {
 			compatible = "cache";
 			reg = <0>;
@@ -65,6 +74,12 @@
 		};
 	};
 
+	apmu@e6152000 {
+		compatible = "renesas,r8a7793-apmu", "renesas,apmu";
+		reg = <0 0xe6152000 0 0x188>;
+		cpus = <&cpu0 &cpu1>;
+	};
+
 	thermal-zones {
 		cpu_thermal: cpu-thermal {
 			polling-delay-passive	= <0>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 40/41] ARM: dts: r8a7793: Add APMU node and second CPU core

[Simon Horman]

From: Magnus Damm <damm+renesas@opensource.se>

Add DT nodes for the Advanced Power Management Unit (APMU) and the
second CPU core.  Use the enable-method to point out that the APMU
should be used for SMP support.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7793.dtsi | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 9b55c1c6ee31..8d02aacf2892 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -35,6 +35,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "renesas,apmu";
 
 		cpu0: cpu at 0 {
 			device_type = "cpu";
@@ -56,6 +57,14 @@
 			next-level-cache = <&L2_CA15>;
 		};
 
+		cpu1: cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+			clock-frequency = <1500000000>;
+			power-domains = <&sysc R8A7793_PD_CA15_CPU1>;
+		};
+
 		L2_CA15: cache-controller at 0 {
 			compatible = "cache";
 			reg = <0>;
@@ -65,6 +74,12 @@
 		};
 	};
 
+	apmu at e6152000 {
+		compatible = "renesas,r8a7793-apmu", "renesas,apmu";
+		reg = <0 0xe6152000 0 0x188>;
+		cpus = <&cpu0 &cpu1>;
+	};
+
 	thermal-zones {
 		cpu_thermal: cpu-thermal {
 			polling-delay-passive	= <0>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 41/41] ARM: dts: r8a7792: add SMP support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add the device tree nodes for the Advanced Power Management Unit (APMU)
and the second Cortex-A15 CPU core.
Use the "enable-method" prop  to point out that the APMU should be used
for the SMP support.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index ad895f8b2353..75256ef4a04d 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -21,6 +21,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -32,6 +33,15 @@
 			next-level-cache = <&L2_CA15>;
 		};
 
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+			clock-frequency = <1000000000>;
+			power-domains = <&sysc R8A7792_PD_CA15_CPU1>;
+			next-level-cache = <&L2_CA15>;
+		};
+
 		L2_CA15: cache-controller@0 {
 			compatible = "cache";
 			reg = <0>;
@@ -49,6 +59,12 @@
 		#size-cells = <2>;
 		ranges;
 
+		apmu@e6152000 {
+			compatible = "renesas,r8a7792-apmu", "renesas,apmu";
+			reg = <0 0xe6152000 0 0x188>;
+			cpus = <&cpu0 &cpu1>;
+		};
+
 		gic: interrupt-controller@f1001000 {
 			compatible = "arm,gic-400";
 			#interrupt-cells = <3>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH 41/41] ARM: dts: r8a7792: add SMP support

[Simon Horman]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Add the device tree nodes for the Advanced Power Management Unit (APMU)
and the second Cortex-A15 CPU core.
Use the "enable-method" prop  to point out that the APMU should be used
for the SMP support.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index ad895f8b2353..75256ef4a04d 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -21,6 +21,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "renesas,apmu";
 
 		cpu0: cpu at 0 {
 			device_type = "cpu";
@@ -32,6 +33,15 @@
 			next-level-cache = <&L2_CA15>;
 		};
 
+		cpu1: cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+			clock-frequency = <1000000000>;
+			power-domains = <&sysc R8A7792_PD_CA15_CPU1>;
+			next-level-cache = <&L2_CA15>;
+		};
+
 		L2_CA15: cache-controller at 0 {
 			compatible = "cache";
 			reg = <0>;
@@ -49,6 +59,12 @@
 		#size-cells = <2>;
 		ranges;
 
+		apmu at e6152000 {
+			compatible = "renesas,r8a7792-apmu", "renesas,apmu";
+			reg = <0 0xe6152000 0 0x188>;
+			cpus = <&cpu0 &cpu1>;
+		};
+
 		gic: interrupt-controller at f1001000 {
 			compatible = "arm,gic-400";
 			#interrupt-cells = <3>;
-- 
2.7.0.rc3.207.g0ac5344

Re: [GIT PULL] Second Round of Renesas ARM Based SoC DT Updates for v4.8

[Olof Johansson]

On Thu, Jun 30, 2016 at 04:15:54PM +0200, Simon Horman wrote:
> Hi Olof, Hi Kevin, Hi Arnd,
> 
> Please consider these second round of Renesas ARM based SoC DT updates for v4.8.
> 
> This pull request is based on the previous round of
> such requests, tagged as renesas-dt-for-v4.8,
> which you have already pulled.
> 
> 
> The following changes since commit b6960f19676e19f37a5e5a8af059fdf3b435d2f4:
> 
>   ARM: dts: silk: Fix W=1 dtc warnings (2016-05-30 09:37:13 +0900)
> 
> are available in the git repository at:
> 
>   git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-dt2-for-v4.8
> 
> for you to fetch changes up to 8fd763c75c3ab8e72e5d7f0d4c53531e6ff76197:
> 
>   ARM: dts: r8a7792: add SMP support (2016-06-30 14:26:14 +0200)

This one also introduces header files but I don't see any dependent driver
changes posted so far, so I'm going to presume that those changes will happen
after this is merged to avoid the cross-tree dependency.


Merged, thanks.


-Olof

[GIT PULL] Second Round of Renesas ARM Based SoC DT Updates for v4.8

[Olof Johansson]

On Thu, Jun 30, 2016 at 04:15:54PM +0200, Simon Horman wrote:
> Hi Olof, Hi Kevin, Hi Arnd,
> 
> Please consider these second round of Renesas ARM based SoC DT updates for v4.8.
> 
> This pull request is based on the previous round of
> such requests, tagged as renesas-dt-for-v4.8,
> which you have already pulled.
> 
> 
> The following changes since commit b6960f19676e19f37a5e5a8af059fdf3b435d2f4:
> 
>   ARM: dts: silk: Fix W=1 dtc warnings (2016-05-30 09:37:13 +0900)
> 
> are available in the git repository at:
> 
>   git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-dt2-for-v4.8
> 
> for you to fetch changes up to 8fd763c75c3ab8e72e5d7f0d4c53531e6ff76197:
> 
>   ARM: dts: r8a7792: add SMP support (2016-06-30 14:26:14 +0200)

This one also introduces header files but I don't see any dependent driver
changes posted so far, so I'm going to presume that those changes will happen
after this is merged to avoid the cross-tree dependency.


Merged, thanks.


-Olof