[U-Boot] [PATCH v2] ARM: imx: Support larger SPL size on IMX6DQ

[U-Boot] [PATCH v2] ARM: imx: Support larger SPL size on IMX6DQ

[Robert Hancock]

Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
---

Changed since v2: Remove "default n" in Kconfig since that is the default.

 arch/arm/mach-imx/mx6/Kconfig |  9 +++++++++
 common/spl/Kconfig            |  3 ++-
 include/configs/imx6_spl.h    | 28 ++++++++++++++++++++++++++--
 3 files changed, 37 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index fe5991e..9c27176 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -87,6 +87,15 @@ config MX6ULL
 	select SYSCOUNTER_TIMER
 	select SYS_L2CACHE_OFF
 
+config MX6_OCRAM_256KB
+	bool "Support 256KB OCRAM"
+	depends on MX6D || MX6Q
+	help
+	 Allows using the full 256KB size of the OCRAM on the MX6Q/MX6D series
+	 of chips, such as for SPL. The OCRAM of the Lite series of chips is
+	 only 128KB, so using this option will prevent the resulting code from
+	 working on those chips.
+
 config MX6_DDRCAL
 	bool "Include dynamic DDR calibration routines"
 	depends on SPL
diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 54154b9..c5ad047 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -28,7 +28,8 @@ config SPL_FRAMEWORK
 config SPL_SIZE_LIMIT
 	int "Maximum size of SPL image"
 	depends on SPL
-	default 69632 if ARCH_MX6
+	default 69632 if ARCH_MX6 && !MX6_OCRAM_256KB
+	default 200704 if ARCH_MX6 && MX6_OCRAM_256KB
 	default 0
 	help
 	  Specifies the maximum length of the U-Boot SPL image.
diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h
index 212dee7..a223930 100644
--- a/include/configs/imx6_spl.h
+++ b/include/configs/imx6_spl.h
@@ -7,10 +7,32 @@
 #define __IMX6_SPL_CONFIG_H
 
 #ifdef CONFIG_SPL
+
+#ifdef CONFIG_MX6_OCRAM_256KB
 /*
- * see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
+ * see Figure 8.4.1 in IMX6DQ Reference manuals:
+ *  - IMX6DQ OCRAM (IRAM) is from 0x00907000 to 0x0093FFFF
+ *  - BOOT ROM stack is at 0x0093FFB8
+ *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
+ *    IMX BOOT ROM will setup MMU table at 0x00938000, therefore we need to
+ *    fit between 0x00907000 and 0x00938000.
+ *  - Additionally the BOOT ROM loads what they consider the firmware image
+ *    which consists of a 4K header in front of us that contains the IVT, DCD
+ *    and some padding thus 'our' max size is really 0x00908000 - 0x00938000
+ *    or 192KB
+ */
+#define CONFIG_SPL_MAX_SIZE		0x30000
+#define CONFIG_SPL_STACK		0x0093FFB8
+/*
+ * Pad SPL to 196KB (4KB header + 192KB max size). This allows to write the
+ * SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a
+ * boot media (given that boot media specific offset is configured properly).
+ */
+#define CONFIG_SPL_PAD_TO		0x31000
+#else
+/*
+ * see Figure 8-3 in IMX6SDL Reference manuals:
  *  - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
- *  - IMX6DQ has 2x IRAM of IMX6SDL but we intend to support IMX6SDL as well
  *  - BOOT ROM stack is at 0x0091FFB8
  *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
  *    IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
@@ -29,6 +51,8 @@
  */
 #define CONFIG_SPL_PAD_TO		0x11000
 
+#endif
+
 /* MMC support */
 #if defined(CONFIG_SPL_MMC_SUPPORT)
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
-- 
1.8.3.1

[U-Boot] [PATCH v2] ARM: imx: Support larger SPL size on IMX6DQ

[Adam Ford]

On Thu, Aug 8, 2019 at 1:14 PM Robert Hancock <hancock@sedsystems.ca> wrote:
>
> Previously the SPL size on all iMX6 platforms was restricted to 68KB
> because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
> other iMX6 variants have 256KB of OCRAM. Add an option
> CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
> don't need to support the SL/DL variants. This allows for an SPL size of
> 196KB, which makes it much easier to use configurations such as SPL with
> driver model and FDT control.
>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic

> Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
> ---
>
> Changed since v2: Remove "default n" in Kconfig since that is the default.
>
>  arch/arm/mach-imx/mx6/Kconfig |  9 +++++++++
>  common/spl/Kconfig            |  3 ++-
>  include/configs/imx6_spl.h    | 28 ++++++++++++++++++++++++++--
>  3 files changed, 37 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
> index fe5991e..9c27176 100644
> --- a/arch/arm/mach-imx/mx6/Kconfig
> +++ b/arch/arm/mach-imx/mx6/Kconfig
> @@ -87,6 +87,15 @@ config MX6ULL
>         select SYSCOUNTER_TIMER
>         select SYS_L2CACHE_OFF
>
> +config MX6_OCRAM_256KB
> +       bool "Support 256KB OCRAM"
> +       depends on MX6D || MX6Q
> +       help
> +        Allows using the full 256KB size of the OCRAM on the MX6Q/MX6D series
> +        of chips, such as for SPL. The OCRAM of the Lite series of chips is
> +        only 128KB, so using this option will prevent the resulting code from
> +        working on those chips.
> +
>  config MX6_DDRCAL
>         bool "Include dynamic DDR calibration routines"
>         depends on SPL
> diff --git a/common/spl/Kconfig b/common/spl/Kconfig
> index 54154b9..c5ad047 100644
> --- a/common/spl/Kconfig
> +++ b/common/spl/Kconfig
> @@ -28,7 +28,8 @@ config SPL_FRAMEWORK
>  config SPL_SIZE_LIMIT
>         int "Maximum size of SPL image"
>         depends on SPL
> -       default 69632 if ARCH_MX6
> +       default 69632 if ARCH_MX6 && !MX6_OCRAM_256KB
> +       default 200704 if ARCH_MX6 && MX6_OCRAM_256KB
>         default 0
>         help
>           Specifies the maximum length of the U-Boot SPL image.
> diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h
> index 212dee7..a223930 100644
> --- a/include/configs/imx6_spl.h
> +++ b/include/configs/imx6_spl.h
> @@ -7,10 +7,32 @@
>  #define __IMX6_SPL_CONFIG_H
>
>  #ifdef CONFIG_SPL
> +
> +#ifdef CONFIG_MX6_OCRAM_256KB
>  /*
> - * see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
> + * see Figure 8.4.1 in IMX6DQ Reference manuals:
> + *  - IMX6DQ OCRAM (IRAM) is from 0x00907000 to 0x0093FFFF
> + *  - BOOT ROM stack is at 0x0093FFB8
> + *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
> + *    IMX BOOT ROM will setup MMU table at 0x00938000, therefore we need to
> + *    fit between 0x00907000 and 0x00938000.
> + *  - Additionally the BOOT ROM loads what they consider the firmware image
> + *    which consists of a 4K header in front of us that contains the IVT, DCD
> + *    and some padding thus 'our' max size is really 0x00908000 - 0x00938000
> + *    or 192KB
> + */
> +#define CONFIG_SPL_MAX_SIZE            0x30000
> +#define CONFIG_SPL_STACK               0x0093FFB8
> +/*
> + * Pad SPL to 196KB (4KB header + 192KB max size). This allows to write the
> + * SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a
> + * boot media (given that boot media specific offset is configured properly).
> + */
> +#define CONFIG_SPL_PAD_TO              0x31000
> +#else
> +/*
> + * see Figure 8-3 in IMX6SDL Reference manuals:
>   *  - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
> - *  - IMX6DQ has 2x IRAM of IMX6SDL but we intend to support IMX6SDL as well
>   *  - BOOT ROM stack is at 0x0091FFB8
>   *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
>   *    IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
> @@ -29,6 +51,8 @@
>   */
>  #define CONFIG_SPL_PAD_TO              0x11000
>
> +#endif
> +
>  /* MMC support */
>  #if defined(CONFIG_SPL_MMC_SUPPORT)
>  #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
> --
> 1.8.3.1
>

[U-Boot] [PATCH v2] ARM: imx: Support larger SPL size on IMX6DQ

[Adam Ford]

On Thu, Aug 8, 2019 at 1:36 PM Adam Ford <aford173@gmail.com> wrote:
>
> On Thu, Aug 8, 2019 at 1:14 PM Robert Hancock <hancock@sedsystems.ca> wrote:
> >
> > Previously the SPL size on all iMX6 platforms was restricted to 68KB
> > because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
> > other iMX6 variants have 256KB of OCRAM. Add an option
> > CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
> > don't need to support the SL/DL variants. This allows for an SPL size of
> > 196KB, which makes it much easier to use configurations such as SPL with
> > driver model and FDT control.
> >
> Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
>
> > Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
> > ---

Stefano,

Any chance this can be adopted?  I have a bunch of patches pending
this, because my SPL is tight and this patch gives it some breathing
room.

thanks,

adam

> >
> > Changed since v2: Remove "default n" in Kconfig since that is the default.
> >
> >  arch/arm/mach-imx/mx6/Kconfig |  9 +++++++++
> >  common/spl/Kconfig            |  3 ++-
> >  include/configs/imx6_spl.h    | 28 ++++++++++++++++++++++++++--
> >  3 files changed, 37 insertions(+), 3 deletions(-)
> >
> > diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
> > index fe5991e..9c27176 100644
> > --- a/arch/arm/mach-imx/mx6/Kconfig
> > +++ b/arch/arm/mach-imx/mx6/Kconfig
> > @@ -87,6 +87,15 @@ config MX6ULL
> >         select SYSCOUNTER_TIMER
> >         select SYS_L2CACHE_OFF
> >
> > +config MX6_OCRAM_256KB
> > +       bool "Support 256KB OCRAM"
> > +       depends on MX6D || MX6Q
> > +       help
> > +        Allows using the full 256KB size of the OCRAM on the MX6Q/MX6D series
> > +        of chips, such as for SPL. The OCRAM of the Lite series of chips is
> > +        only 128KB, so using this option will prevent the resulting code from
> > +        working on those chips.
> > +
> >  config MX6_DDRCAL
> >         bool "Include dynamic DDR calibration routines"
> >         depends on SPL
> > diff --git a/common/spl/Kconfig b/common/spl/Kconfig
> > index 54154b9..c5ad047 100644
> > --- a/common/spl/Kconfig
> > +++ b/common/spl/Kconfig
> > @@ -28,7 +28,8 @@ config SPL_FRAMEWORK
> >  config SPL_SIZE_LIMIT
> >         int "Maximum size of SPL image"
> >         depends on SPL
> > -       default 69632 if ARCH_MX6
> > +       default 69632 if ARCH_MX6 && !MX6_OCRAM_256KB
> > +       default 200704 if ARCH_MX6 && MX6_OCRAM_256KB
> >         default 0
> >         help
> >           Specifies the maximum length of the U-Boot SPL image.
> > diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h
> > index 212dee7..a223930 100644
> > --- a/include/configs/imx6_spl.h
> > +++ b/include/configs/imx6_spl.h
> > @@ -7,10 +7,32 @@
> >  #define __IMX6_SPL_CONFIG_H
> >
> >  #ifdef CONFIG_SPL
> > +
> > +#ifdef CONFIG_MX6_OCRAM_256KB
> >  /*
> > - * see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
> > + * see Figure 8.4.1 in IMX6DQ Reference manuals:
> > + *  - IMX6DQ OCRAM (IRAM) is from 0x00907000 to 0x0093FFFF
> > + *  - BOOT ROM stack is at 0x0093FFB8
> > + *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
> > + *    IMX BOOT ROM will setup MMU table at 0x00938000, therefore we need to
> > + *    fit between 0x00907000 and 0x00938000.
> > + *  - Additionally the BOOT ROM loads what they consider the firmware image
> > + *    which consists of a 4K header in front of us that contains the IVT, DCD
> > + *    and some padding thus 'our' max size is really 0x00908000 - 0x00938000
> > + *    or 192KB
> > + */
> > +#define CONFIG_SPL_MAX_SIZE            0x30000
> > +#define CONFIG_SPL_STACK               0x0093FFB8
> > +/*
> > + * Pad SPL to 196KB (4KB header + 192KB max size). This allows to write the
> > + * SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a
> > + * boot media (given that boot media specific offset is configured properly).
> > + */
> > +#define CONFIG_SPL_PAD_TO              0x31000
> > +#else
> > +/*
> > + * see Figure 8-3 in IMX6SDL Reference manuals:
> >   *  - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
> > - *  - IMX6DQ has 2x IRAM of IMX6SDL but we intend to support IMX6SDL as well
> >   *  - BOOT ROM stack is at 0x0091FFB8
> >   *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
> >   *    IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
> > @@ -29,6 +51,8 @@
> >   */
> >  #define CONFIG_SPL_PAD_TO              0x11000
> >
> > +#endif
> > +
> >  /* MMC support */
> >  #if defined(CONFIG_SPL_MMC_SUPPORT)
> >  #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
> > --
> > 1.8.3.1
> >

[U-Boot] [PATCH v2] ARM: imx: Support larger SPL size on IMX6DQ

[Adam Ford]

On Mon, Aug 26, 2019 at 8:00 AM Adam Ford <aford173@gmail.com> wrote:
>
> On Thu, Aug 8, 2019 at 1:36 PM Adam Ford <aford173@gmail.com> wrote:
> >
> > On Thu, Aug 8, 2019 at 1:14 PM Robert Hancock <hancock@sedsystems.ca> wrote:
> > >
> > > Previously the SPL size on all iMX6 platforms was restricted to 68KB
> > > because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
> > > other iMX6 variants have 256KB of OCRAM. Add an option
> > > CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
> > > don't need to support the SL/DL variants. This allows for an SPL size of
> > > 196KB, which makes it much easier to use configurations such as SPL with
> > > driver model and FDT control.
> > >
> > Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
> >
> > > Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
> > > ---
>
> Stefano,
>
> Any chance this can be adopted?  I have a bunch of patches pending
> this, because my SPL is tight and this patch gives it some breathing
> room.
>

It's been over a month.  Is there any reason this cannot be applied?

thanks

adam

> thanks,
>
> adam
>
> > >
> > > Changed since v2: Remove "default n" in Kconfig since that is the default.
> > >
> > >  arch/arm/mach-imx/mx6/Kconfig |  9 +++++++++
> > >  common/spl/Kconfig            |  3 ++-
> > >  include/configs/imx6_spl.h    | 28 ++++++++++++++++++++++++++--
> > >  3 files changed, 37 insertions(+), 3 deletions(-)
> > >
> > > diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
> > > index fe5991e..9c27176 100644
> > > --- a/arch/arm/mach-imx/mx6/Kconfig
> > > +++ b/arch/arm/mach-imx/mx6/Kconfig
> > > @@ -87,6 +87,15 @@ config MX6ULL
> > >         select SYSCOUNTER_TIMER
> > >         select SYS_L2CACHE_OFF
> > >
> > > +config MX6_OCRAM_256KB
> > > +       bool "Support 256KB OCRAM"
> > > +       depends on MX6D || MX6Q
> > > +       help
> > > +        Allows using the full 256KB size of the OCRAM on the MX6Q/MX6D series
> > > +        of chips, such as for SPL. The OCRAM of the Lite series of chips is
> > > +        only 128KB, so using this option will prevent the resulting code from
> > > +        working on those chips.
> > > +
> > >  config MX6_DDRCAL
> > >         bool "Include dynamic DDR calibration routines"
> > >         depends on SPL
> > > diff --git a/common/spl/Kconfig b/common/spl/Kconfig
> > > index 54154b9..c5ad047 100644
> > > --- a/common/spl/Kconfig
> > > +++ b/common/spl/Kconfig
> > > @@ -28,7 +28,8 @@ config SPL_FRAMEWORK
> > >  config SPL_SIZE_LIMIT
> > >         int "Maximum size of SPL image"
> > >         depends on SPL
> > > -       default 69632 if ARCH_MX6
> > > +       default 69632 if ARCH_MX6 && !MX6_OCRAM_256KB
> > > +       default 200704 if ARCH_MX6 && MX6_OCRAM_256KB
> > >         default 0
> > >         help
> > >           Specifies the maximum length of the U-Boot SPL image.
> > > diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h
> > > index 212dee7..a223930 100644
> > > --- a/include/configs/imx6_spl.h
> > > +++ b/include/configs/imx6_spl.h
> > > @@ -7,10 +7,32 @@
> > >  #define __IMX6_SPL_CONFIG_H
> > >
> > >  #ifdef CONFIG_SPL
> > > +
> > > +#ifdef CONFIG_MX6_OCRAM_256KB
> > >  /*
> > > - * see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
> > > + * see Figure 8.4.1 in IMX6DQ Reference manuals:
> > > + *  - IMX6DQ OCRAM (IRAM) is from 0x00907000 to 0x0093FFFF
> > > + *  - BOOT ROM stack is at 0x0093FFB8
> > > + *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
> > > + *    IMX BOOT ROM will setup MMU table at 0x00938000, therefore we need to
> > > + *    fit between 0x00907000 and 0x00938000.
> > > + *  - Additionally the BOOT ROM loads what they consider the firmware image
> > > + *    which consists of a 4K header in front of us that contains the IVT, DCD
> > > + *    and some padding thus 'our' max size is really 0x00908000 - 0x00938000
> > > + *    or 192KB
> > > + */
> > > +#define CONFIG_SPL_MAX_SIZE            0x30000
> > > +#define CONFIG_SPL_STACK               0x0093FFB8
> > > +/*
> > > + * Pad SPL to 196KB (4KB header + 192KB max size). This allows to write the
> > > + * SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a
> > > + * boot media (given that boot media specific offset is configured properly).
> > > + */
> > > +#define CONFIG_SPL_PAD_TO              0x31000
> > > +#else
> > > +/*
> > > + * see Figure 8-3 in IMX6SDL Reference manuals:
> > >   *  - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
> > > - *  - IMX6DQ has 2x IRAM of IMX6SDL but we intend to support IMX6SDL as well
> > >   *  - BOOT ROM stack is at 0x0091FFB8
> > >   *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
> > >   *    IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
> > > @@ -29,6 +51,8 @@
> > >   */
> > >  #define CONFIG_SPL_PAD_TO              0x11000
> > >
> > > +#endif
> > > +
> > >  /* MMC support */
> > >  #if defined(CONFIG_SPL_MMC_SUPPORT)
> > >  #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
> > > --
> > > 1.8.3.1
> > >

[U-Boot] [PATCH v2] ARM: imx: Support larger SPL size on IMX6DQ

[Fabio Estevam]

On Fri, Sep 27, 2019 at 9:17 AM Adam Ford <aford173@gmail.com> wrote:

> It's been over a month.  Is there any reason this cannot be applied?

It has been applied in Stefano's tree:
https://gitlab.denx.de/u-boot/custodians/u-boot-imx/commit/90fb571d61a8967f5e56c5b03db5e44889325bde

[U-Boot] [PATCH v2] ARM: imx: Support larger SPL size on IMX6DQ

[Adam Ford]

On Fri, Sep 27, 2019 at 7:31 AM Fabio Estevam <festevam@gmail.com> wrote:
>
> On Fri, Sep 27, 2019 at 9:17 AM Adam Ford <aford173@gmail.com> wrote:
>
> > It's been over a month.  Is there any reason this cannot be applied?
>
> It has been applied in Stefano's tree:
> https://gitlab.denx.de/u-boot/custodians/u-boot-imx/commit/90fb571d61a8967f5e56c5b03db5e44889325bde

Fantastic!  I just looked at master.  Hopefully it'll get pulled after
the next pull request.

Thank you,

adam

[U-Boot] [PATCH v2] ARM: imx: Support larger SPL size on IMX6DQ

[Stefano Babic]

On 27/09/19 14:32, Adam Ford wrote:
> On Fri, Sep 27, 2019 at 7:31 AM Fabio Estevam <festevam@gmail.com> wrote:
>>
>> On Fri, Sep 27, 2019 at 9:17 AM Adam Ford <aford173@gmail.com> wrote:
>>
>>> It's been over a month.  Is there any reason this cannot be applied?
>>
>> It has been applied in Stefano's tree:
>> https://gitlab.denx.de/u-boot/custodians/u-boot-imx/commit/90fb571d61a8967f5e56c5b03db5e44889325bde
> 
> Fantastic!  I just looked at master.  Hopefully it'll get pulled after
> the next pull request.

My last PR was rejected (at least, discouraged) due to the number of
changes and release is approaching. But I will not try to pick up random
patches from u-boot-imx master and try to push it just to get it in
release. I am starting to pick up all pacthes that are ready in -next,
starting from u-boot-imx, -master.

Regards,
Stefano

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v2] ARM: imx: Support larger SPL size on IMX6DQ

[Adam Ford]

On Fri, Sep 27, 2019 at 7:53 AM Stefano Babic <sbabic@denx.de> wrote:
>
> On 27/09/19 14:32, Adam Ford wrote:
> > On Fri, Sep 27, 2019 at 7:31 AM Fabio Estevam <festevam@gmail.com> wrote:
> >>
> >> On Fri, Sep 27, 2019 at 9:17 AM Adam Ford <aford173@gmail.com> wrote:
> >>
> >>> It's been over a month.  Is there any reason this cannot be applied?
> >>
> >> It has been applied in Stefano's tree:
> >> https://gitlab.denx.de/u-boot/custodians/u-boot-imx/commit/90fb571d61a8967f5e56c5b03db5e44889325bde
> >
> > Fantastic!  I just looked at master.  Hopefully it'll get pulled after
> > the next pull request.
>
> My last PR was rejected (at least, discouraged) due to the number of
> changes and release is approaching. But I will not try to pick up random
> patches from u-boot-imx master and try to push it just to get it in
> release. I am starting to pick up all pacthes that are ready in -next,
> starting from u-boot-imx, -master.
>

That makes sense since this is an improvement and not a bug fix.

adam
> Regards,
> Stefano
>
> --
> =====================================================================
> DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
> =====================================================================