* multipathd will not set the iscsi session tmo after iscsi sesstion recovery
@ 2018-04-12 8:46 jianchao.wang
2018-04-17 2:11 ` jianchao.wang
0 siblings, 1 reply; 4+ messages in thread
From: jianchao.wang @ 2018-04-12 8:46 UTC (permalink / raw)
To: christophe.varoqui, dm-devel; +Cc: shinya.narahara
Hi Dear all
Our customer complained that the iscsi session tmo parameters doesn't match with
the multipath config.
When the iscsi session fails and do the recovery, iscsid will set parameters again.
But this will overwrite the ones which has been set by multipathd.
And multipathd will not set the iscsi session tmo parameters when path down and up.
Is there any solution for this ?
Thanks
Jianchao
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: multipathd will not set the iscsi session tmo after iscsi sesstion recovery
2018-04-12 8:46 multipathd will not set the iscsi session tmo after iscsi sesstion recovery jianchao.wang
@ 2018-04-17 2:11 ` jianchao.wang
2018-04-17 19:26 ` Benjamin Marzinski
0 siblings, 1 reply; 4+ messages in thread
From: jianchao.wang @ 2018-04-17 2:11 UTC (permalink / raw)
To: christophe.varoqui, dm-devel; +Cc: shinya.narahara
Would anyone please provide some suggestion ?
Thanks in advance
Jianchao
On 04/12/2018 04:46 PM, jianchao.wang wrote:
> Hi Dear all
>
> Our customer complained that the iscsi session tmo parameters doesn't match with
> the multipath config.
>
> When the iscsi session fails and do the recovery, iscsid will set parameters again.
> But this will overwrite the ones which has been set by multipathd.
> And multipathd will not set the iscsi session tmo parameters when path down and up.
>
> Is there any solution for this ?
>
> Thanks
> Jianchao
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: multipathd will not set the iscsi session tmo after iscsi sesstion recovery
2018-04-17 2:11 ` jianchao.wang
@ 2018-04-17 19:26 ` Benjamin Marzinski
2018-04-18 2:33 ` jianchao.wang
0 siblings, 1 reply; 4+ messages in thread
From: Benjamin Marzinski @ 2018-04-17 19:26 UTC (permalink / raw)
To: jianchao.wang; +Cc: dm-devel, shinya.narahara
On Tue, Apr 17, 2018 at 10:11:48AM +0800, jianchao.wang wrote:
> Would anyone please provide some suggestion ?
>
> Thanks in advance
> Jianchao
>
> On 04/12/2018 04:46 PM, jianchao.wang wrote:
> > Hi Dear all
> >
> > Our customer complained that the iscsi session tmo parameters doesn't match with
> > the multipath config.
> >
> > When the iscsi session fails and do the recovery, iscsid will set parameters again.
> > But this will overwrite the ones which has been set by multipathd.
> > And multipathd will not set the iscsi session tmo parameters when path down and up.
I would rather see if iscsid could skip reseting the parameters if they have
been changed outside the program. If not, then multipathd could check
and reset the parameters whenever a path comes back up. But if iscsid
is resetting it there, might it not be resetting it elsewhere?
-Ben
> >
> > Is there any solution for this ?
> >
> > Thanks
> > Jianchao
> >
>
> --
> dm-devel mailing list
> dm-devel@redhat.com
> https://www.redhat.com/mailman/listinfo/dm-devel
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: multipathd will not set the iscsi session tmo after iscsi sesstion recovery
2018-04-17 19:26 ` Benjamin Marzinski
@ 2018-04-18 2:33 ` jianchao.wang
0 siblings, 0 replies; 4+ messages in thread
From: jianchao.wang @ 2018-04-18 2:33 UTC (permalink / raw)
To: Benjamin Marzinski; +Cc: dm-devel, shinya.narahara
Hi Ben
Thanks for your kindly response.
On 04/18/2018 03:26 AM, Benjamin Marzinski wrote:
>>> When the iscsi session fails and do the recovery, iscsid will set parameters again.
>>> But this will overwrite the ones which has been set by multipathd.
>>> And multipathd will not set the iscsi session tmo parameters when path down and up.
> I would rather see if iscsid could skip reseting the parameters if they have
> been changed outside the program. If not, then multipathd could check
> and reset the parameters whenever a path comes back up. But if iscsid
> is resetting it there, might it not be resetting it elsewhere?
As I know, iscsid would only set the parameters during setup the session.
multipathd + iscsid is common case, it is really worthy to provide a fix
for the parameter reseting when path up/down.
Thanks
Jianchao
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2018-04-18 2:33 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-04-12 8:46 multipathd will not set the iscsi session tmo after iscsi sesstion recovery jianchao.wang
2018-04-17 2:11 ` jianchao.wang
2018-04-17 19:26 ` Benjamin Marzinski
2018-04-18 2:33 ` jianchao.wang
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.