[PATCH v2 0/3] arm64: dts: Add IOT2050 M.2 board, describe QSPI layout

[PATCH v2 0/3] arm64: dts: Add IOT2050 M.2 board, describe QSPI layout

[Jan Kiszka]

This adds the devices tree for a new variant of the IOT2050 which comes
with two M.2 slots and is otherwise almost equivalent to the existing
Advanced PG2 variant (USB3 is available via M.2 now).

Furthermore, the device tree of the whole device series is extended to
also hold the QSPI layout.

Changes in v2:
 - alphabetic ordering in binding schema and makefile
 - dropped an unneeded blank line in patch 3

Jan

Jan Kiszka (2):
  arm64: dts: ti: iot2050: Add layout of OSPI flash
  dt-bindings: arm: ti: Add binding for Siemens IOT2050 M.2 variant

chao zeng (1):
  arm64: dts: ti: iot2050: Add support for M.2 variant

 .../devicetree/bindings/arm/ti/k3.yaml        |   1 +
 arch/arm64/boot/dts/ti/Makefile               |   3 +
 .../boot/dts/ti/k3-am65-iot2050-common.dtsi   |  46 +++++++
 .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
 4 files changed, 171 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts

-- 
2.35.3

[PATCH v2 0/3] arm64: dts: Add IOT2050 M.2 board, describe QSPI layout

[Jan Kiszka]

This adds the devices tree for a new variant of the IOT2050 which comes
with two M.2 slots and is otherwise almost equivalent to the existing
Advanced PG2 variant (USB3 is available via M.2 now).

Furthermore, the device tree of the whole device series is extended to
also hold the QSPI layout.

Changes in v2:
 - alphabetic ordering in binding schema and makefile
 - dropped an unneeded blank line in patch 3

Jan

Jan Kiszka (2):
  arm64: dts: ti: iot2050: Add layout of OSPI flash
  dt-bindings: arm: ti: Add binding for Siemens IOT2050 M.2 variant

chao zeng (1):
  arm64: dts: ti: iot2050: Add support for M.2 variant

 .../devicetree/bindings/arm/ti/k3.yaml        |   1 +
 arch/arm64/boot/dts/ti/Makefile               |   3 +
 .../boot/dts/ti/k3-am65-iot2050-common.dtsi   |  46 +++++++
 .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
 4 files changed, 171 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts

-- 
2.35.3


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 1/3] arm64: dts: ti: iot2050: Add layout of OSPI flash

[Jan Kiszka]

From: Jan Kiszka <jan.kiszka@siemens.com>

Describe the layout of the OSPI flash as the latest firmware uses it.
Specifically the location of the U-Boot envs is important for userspace
in order to access it.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
 .../boot/dts/ti/k3-am65-iot2050-common.dtsi   | 46 +++++++++++++++++++
 1 file changed, 46 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 3cced26b520a..96ac2b476b11 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -609,6 +609,52 @@ flash@0 {
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			seboot@0 {
+				label = "seboot";
+				reg = <0x0 0x180000>; /* 1.5M */
+			};
+
+			tispl@180000 {
+				label = "tispl";
+				reg = <0x180000 0x200000>; /* 2M */
+			};
+
+			u-boot@380000 {
+				label = "u-boot";
+				reg = <0x380000 0x300000>; /* 3M */
+			};
+
+			env@680000 {
+				label = "env";
+				reg = <0x680000 0x20000>; /* 128K */
+			};
+
+			env-backup@6a0000 {
+				label = "env.backup";
+				reg = <0x6a0000 0x20000>; /* 128K */
+			};
+
+			otpcmd@6c0000 {
+				label = "otpcmd";
+				reg = <0x6c0000 0x10000>; /* 64K */
+			};
+
+			unused@6d0000 {
+				label = "unused";
+				reg = <0x6d0000 0x7b0000>; /* 7872K */
+			};
+
+			seboot-backup@e80000 {
+				label = "seboot.backup";
+				reg = <0xe80000 0x180000>; /* 1.5M */
+			};
+		};
 	};
 };
 
-- 
2.35.3

[PATCH v2 1/3] arm64: dts: ti: iot2050: Add layout of OSPI flash

[Jan Kiszka]

From: Jan Kiszka <jan.kiszka@siemens.com>

Describe the layout of the OSPI flash as the latest firmware uses it.
Specifically the location of the U-Boot envs is important for userspace
in order to access it.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
 .../boot/dts/ti/k3-am65-iot2050-common.dtsi   | 46 +++++++++++++++++++
 1 file changed, 46 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 3cced26b520a..96ac2b476b11 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -609,6 +609,52 @@ flash@0 {
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			seboot@0 {
+				label = "seboot";
+				reg = <0x0 0x180000>; /* 1.5M */
+			};
+
+			tispl@180000 {
+				label = "tispl";
+				reg = <0x180000 0x200000>; /* 2M */
+			};
+
+			u-boot@380000 {
+				label = "u-boot";
+				reg = <0x380000 0x300000>; /* 3M */
+			};
+
+			env@680000 {
+				label = "env";
+				reg = <0x680000 0x20000>; /* 128K */
+			};
+
+			env-backup@6a0000 {
+				label = "env.backup";
+				reg = <0x6a0000 0x20000>; /* 128K */
+			};
+
+			otpcmd@6c0000 {
+				label = "otpcmd";
+				reg = <0x6c0000 0x10000>; /* 64K */
+			};
+
+			unused@6d0000 {
+				label = "unused";
+				reg = <0x6d0000 0x7b0000>; /* 7872K */
+			};
+
+			seboot-backup@e80000 {
+				label = "seboot.backup";
+				reg = <0xe80000 0x180000>; /* 1.5M */
+			};
+		};
 	};
 };
 
-- 
2.35.3


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/3] dt-bindings: arm: ti: Add binding for Siemens IOT2050 M.2 variant

[Jan Kiszka]

From: Jan Kiszka <jan.kiszka@siemens.com>

This new variant is derived from the Advanced PG2 board, replacing the
MiniPCI slot with B and E-keyed M.2 slots.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/arm/ti/k3.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml
index 203faab80142..0ed4e973753f 100644
--- a/Documentation/devicetree/bindings/arm/ti/k3.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml
@@ -42,6 +42,7 @@ properties:
         items:
           - enum:
               - siemens,iot2050-advanced
+              - siemens,iot2050-advanced-m2
               - siemens,iot2050-advanced-pg2
               - siemens,iot2050-basic
               - siemens,iot2050-basic-pg2
-- 
2.35.3

[PATCH v2 2/3] dt-bindings: arm: ti: Add binding for Siemens IOT2050 M.2 variant

[Jan Kiszka]

From: Jan Kiszka <jan.kiszka@siemens.com>

This new variant is derived from the Advanced PG2 board, replacing the
MiniPCI slot with B and E-keyed M.2 slots.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/arm/ti/k3.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml
index 203faab80142..0ed4e973753f 100644
--- a/Documentation/devicetree/bindings/arm/ti/k3.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml
@@ -42,6 +42,7 @@ properties:
         items:
           - enum:
               - siemens,iot2050-advanced
+              - siemens,iot2050-advanced-m2
               - siemens,iot2050-advanced-pg2
               - siemens,iot2050-basic
               - siemens,iot2050-basic-pg2
-- 
2.35.3


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 3/3] arm64: dts: ti: iot2050: Add support for M.2 variant

[Jan Kiszka]

From: chao zeng <chao.zeng@siemens.com>

The M.2 variant comes with 2 slots, one B-keyed and another one E-keyed.
They are configured by the firmware during startup. Also the device tree
will be adjusted according to the detect or manually configured
interface mode by the firmware. The kernel only carries a single
configuration as base device tree. It has to be built with a symbols
node so that the firmware can apply overlays for the connector modes.

Signed-off-by: chao zeng <chao.zeng@siemens.com>
[Jan: refactored to a single DT]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
 arch/arm64/boot/dts/ti/Makefile               |   3 +
 .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
 2 files changed, 124 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index cf7c509538a4..bfb16b62c58d 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -10,8 +10,11 @@ dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-m2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
 
+DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
+
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
new file mode 100644
index 000000000000..9400e35882a6
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2023
+ *
+ * Authors:
+ *   Chao Zeng <chao.zeng@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * AM6548-based (quad-core) IOT2050 M.2 variant (based on Advanced Product
+ * Generation 2), 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
+ */
+
+#include "k3-am6548-iot2050-advanced-common.dtsi"
+#include "k3-am65-iot2050-common-pg2.dtsi"
+
+/ {
+	compatible = "siemens,iot2050-advanced-m2", "ti,am654";
+	model = "SIMATIC IOT2050 Advanced M2";
+};
+
+&mcu_r5fss0 {
+	/* lock-step mode not supported on this board */
+	ti,cluster-mode = <0>;
+};
+
+&main_pmx0 {
+	main_m2_enable_pins_default: main-m2-enable-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01c4, PIN_INPUT_PULLUP, 7)  /* (AH13) GPIO1_17 */
+		>;
+	};
+
+	main_bkey_pcie_reset: main-bkey-pcie-reset {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01bc, PIN_OUTPUT_PULLUP, 7)  /* (AG13) GPIO1_15 */
+		>;
+	};
+
+	main_pmx0_m2_config_pins_default: main-pmx0-m2-config-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01c8, PIN_INPUT_PULLUP, 7)  /* (AE13) GPIO1_18 */
+			AM65X_IOPAD(0x01cc, PIN_INPUT_PULLUP, 7)  /* (AD13) GPIO1_19 */
+		>;
+	};
+
+	main_m2_pcie_mux_control: main-m2-pcie-mux-control {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x0148, PIN_INPUT_PULLUP, 7)  /* (AG22) GPIO0_82 */
+			AM65X_IOPAD(0x0160, PIN_INPUT_PULLUP, 7)  /* (AE20) GPIO0_88 */
+			AM65X_IOPAD(0x0164, PIN_INPUT_PULLUP, 7)  /* (AF19) GPIO0_89 */
+		>;
+	};
+};
+
+&main_pmx1 {
+	main_pmx1_m2_config_pins_default: main-pmx1-m2-config-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x0018, PIN_INPUT_PULLUP, 7)  /* (B22) GPIO1_88 */
+			AM65X_IOPAD(0x001c, PIN_INPUT_PULLUP, 7)  /* (C23) GPIO1_89 */
+		>;
+	};
+};
+
+&main_gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&main_m2_pcie_mux_control
+		&arduino_io_d4_to_d9_pins_default
+	>;
+};
+
+&main_gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&main_m2_enable_pins_default
+		&main_pmx0_m2_config_pins_default
+		&main_pmx1_m2_config_pins_default
+		&cp2102n_reset_pin_default
+	>;
+};
+
+/*
+ * Base configuration for B-key slot with PCIe x2, E-key with USB 2.0 only.
+ * Firmware switches to other modes via device tree overlays.
+ */
+
+&serdes0 {
+	assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>;
+	assigned-clock-parents = <&k3_clks 153 8>, <&k3_clks 153 4>;
+};
+
+&pcie0_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_bkey_pcie_reset>;
+
+	num-lanes = <2>;
+	phys = <&serdes0 PHY_TYPE_PCIE 1>, <&serdes1 PHY_TYPE_PCIE 1>;
+	phy-names = "pcie-phy0","pcie-phy1";
+	reset-gpios = <&main_gpio1 15 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&pcie1_rc {
+	status = "disabled";
+};
+
+&dwc3_0 {
+	assigned-clock-parents = <&k3_clks 151 4>,  /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
+				 <&k3_clks 151 9>;  /* set PIPE3_TXB_CLK to CLK_12M_RC/256 (for HS only) */
+	/delete-property/ phys;
+	/delete-property/ phy-names;
+};
+
+&usb0 {
+	maximum-speed = "high-speed";
+	/delete-property/ snps,dis-u1-entry-quirk;
+	/delete-property/ snps,dis-u2-entry-quirk;
+};
-- 
2.35.3

[PATCH v2 3/3] arm64: dts: ti: iot2050: Add support for M.2 variant

[Jan Kiszka]

From: chao zeng <chao.zeng@siemens.com>

The M.2 variant comes with 2 slots, one B-keyed and another one E-keyed.
They are configured by the firmware during startup. Also the device tree
will be adjusted according to the detect or manually configured
interface mode by the firmware. The kernel only carries a single
configuration as base device tree. It has to be built with a symbols
node so that the firmware can apply overlays for the connector modes.

Signed-off-by: chao zeng <chao.zeng@siemens.com>
[Jan: refactored to a single DT]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
 arch/arm64/boot/dts/ti/Makefile               |   3 +
 .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
 2 files changed, 124 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index cf7c509538a4..bfb16b62c58d 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -10,8 +10,11 @@ dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-m2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
 
+DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
+
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
new file mode 100644
index 000000000000..9400e35882a6
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2023
+ *
+ * Authors:
+ *   Chao Zeng <chao.zeng@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * AM6548-based (quad-core) IOT2050 M.2 variant (based on Advanced Product
+ * Generation 2), 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
+ */
+
+#include "k3-am6548-iot2050-advanced-common.dtsi"
+#include "k3-am65-iot2050-common-pg2.dtsi"
+
+/ {
+	compatible = "siemens,iot2050-advanced-m2", "ti,am654";
+	model = "SIMATIC IOT2050 Advanced M2";
+};
+
+&mcu_r5fss0 {
+	/* lock-step mode not supported on this board */
+	ti,cluster-mode = <0>;
+};
+
+&main_pmx0 {
+	main_m2_enable_pins_default: main-m2-enable-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01c4, PIN_INPUT_PULLUP, 7)  /* (AH13) GPIO1_17 */
+		>;
+	};
+
+	main_bkey_pcie_reset: main-bkey-pcie-reset {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01bc, PIN_OUTPUT_PULLUP, 7)  /* (AG13) GPIO1_15 */
+		>;
+	};
+
+	main_pmx0_m2_config_pins_default: main-pmx0-m2-config-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01c8, PIN_INPUT_PULLUP, 7)  /* (AE13) GPIO1_18 */
+			AM65X_IOPAD(0x01cc, PIN_INPUT_PULLUP, 7)  /* (AD13) GPIO1_19 */
+		>;
+	};
+
+	main_m2_pcie_mux_control: main-m2-pcie-mux-control {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x0148, PIN_INPUT_PULLUP, 7)  /* (AG22) GPIO0_82 */
+			AM65X_IOPAD(0x0160, PIN_INPUT_PULLUP, 7)  /* (AE20) GPIO0_88 */
+			AM65X_IOPAD(0x0164, PIN_INPUT_PULLUP, 7)  /* (AF19) GPIO0_89 */
+		>;
+	};
+};
+
+&main_pmx1 {
+	main_pmx1_m2_config_pins_default: main-pmx1-m2-config-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x0018, PIN_INPUT_PULLUP, 7)  /* (B22) GPIO1_88 */
+			AM65X_IOPAD(0x001c, PIN_INPUT_PULLUP, 7)  /* (C23) GPIO1_89 */
+		>;
+	};
+};
+
+&main_gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&main_m2_pcie_mux_control
+		&arduino_io_d4_to_d9_pins_default
+	>;
+};
+
+&main_gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&main_m2_enable_pins_default
+		&main_pmx0_m2_config_pins_default
+		&main_pmx1_m2_config_pins_default
+		&cp2102n_reset_pin_default
+	>;
+};
+
+/*
+ * Base configuration for B-key slot with PCIe x2, E-key with USB 2.0 only.
+ * Firmware switches to other modes via device tree overlays.
+ */
+
+&serdes0 {
+	assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>;
+	assigned-clock-parents = <&k3_clks 153 8>, <&k3_clks 153 4>;
+};
+
+&pcie0_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_bkey_pcie_reset>;
+
+	num-lanes = <2>;
+	phys = <&serdes0 PHY_TYPE_PCIE 1>, <&serdes1 PHY_TYPE_PCIE 1>;
+	phy-names = "pcie-phy0","pcie-phy1";
+	reset-gpios = <&main_gpio1 15 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&pcie1_rc {
+	status = "disabled";
+};
+
+&dwc3_0 {
+	assigned-clock-parents = <&k3_clks 151 4>,  /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
+				 <&k3_clks 151 9>;  /* set PIPE3_TXB_CLK to CLK_12M_RC/256 (for HS only) */
+	/delete-property/ phys;
+	/delete-property/ phy-names;
+};
+
+&usb0 {
+	maximum-speed = "high-speed";
+	/delete-property/ snps,dis-u1-entry-quirk;
+	/delete-property/ snps,dis-u2-entry-quirk;
+};
-- 
2.35.3


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 3/3] arm64: dts: ti: iot2050: Add support for M.2 variant

[Siddharth Vadapalli]

On 19/01/23 12:10, Jan Kiszka wrote:
> From: chao zeng <chao.zeng@siemens.com>
> 
> The M.2 variant comes with 2 slots, one B-keyed and another one E-keyed.
> They are configured by the firmware during startup. Also the device tree
> will be adjusted according to the detect or manually configured
> interface mode by the firmware. The kernel only carries a single
> configuration as base device tree. It has to be built with a symbols
> node so that the firmware can apply overlays for the connector modes.
> 
> Signed-off-by: chao zeng <chao.zeng@siemens.com>
> [Jan: refactored to a single DT]
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
>  arch/arm64/boot/dts/ti/Makefile               |   3 +
>  .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
>  2 files changed, 124 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts

Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>

Regards,
Siddharth.

Re: [PATCH v2 3/3] arm64: dts: ti: iot2050: Add support for M.2 variant

[Siddharth Vadapalli]

On 19/01/23 12:10, Jan Kiszka wrote:
> From: chao zeng <chao.zeng@siemens.com>
> 
> The M.2 variant comes with 2 slots, one B-keyed and another one E-keyed.
> They are configured by the firmware during startup. Also the device tree
> will be adjusted according to the detect or manually configured
> interface mode by the firmware. The kernel only carries a single
> configuration as base device tree. It has to be built with a symbols
> node so that the firmware can apply overlays for the connector modes.
> 
> Signed-off-by: chao zeng <chao.zeng@siemens.com>
> [Jan: refactored to a single DT]
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
>  arch/arm64/boot/dts/ti/Makefile               |   3 +
>  .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
>  2 files changed, 124 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts

Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>

Regards,
Siddharth.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel