* [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-02 17:05 ` sean.wang
0 siblings, 0 replies; 27+ messages in thread
From: sean.wang @ 2017-08-02 17:05 UTC (permalink / raw)
To: robh+dt, gregkh, jslaby, andriy.shevchenko, jan.kiszka,
heikki.krogerus, hpeter, vigneshr, matthias.bgg
Cc: devicetree, linux-mediatek, linux-serial, linux-arm-kernel,
linux-kernel, Sean Wang
From: Sean Wang <sean.wang@mediatek.com>
This patchset introduces the support for MediaTek BTIF controller.
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module also called CONNSYS inside the SoC which could be
mostly found on those MediaTek SoCs with Bluetooth feature.
And the controller is made as being compatible with the 8250 register
layout so it tends to be integrated with existing 8250 core driver and
have no requirement for the modem configuration additionally such as the
baud rate calculation and assignment.
Sean Wang (2):
dt-bindings: serial: Add MediaTek BTIF controller bindings
tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623
SoC
.../devicetree/bindings/serial/mtk-btif.txt | 26 +++
drivers/tty/serial/8250/8250_btif.c | 224 +++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 9 +
drivers/tty/serial/8250/Makefile | 1 +
4 files changed, 260 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
create mode 100644 drivers/tty/serial/8250/8250_btif.c
--
2.7.4
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-02 17:05 ` sean.wang
0 siblings, 0 replies; 27+ messages in thread
From: sean.wang @ 2017-08-02 17:05 UTC (permalink / raw)
To: robh+dt, gregkh, jslaby, andriy.shevchenko, jan.kiszka,
heikki.krogerus, hpeter, vigneshr, matthias.bgg
Cc: devicetree, linux-mediatek, linux-serial, linux-arm-kernel,
linux-kernel, Sean Wang
From: Sean Wang <sean.wang@mediatek.com>
This patchset introduces the support for MediaTek BTIF controller.
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module also called CONNSYS inside the SoC which could be
mostly found on those MediaTek SoCs with Bluetooth feature.
And the controller is made as being compatible with the 8250 register
layout so it tends to be integrated with existing 8250 core driver and
have no requirement for the modem configuration additionally such as the
baud rate calculation and assignment.
Sean Wang (2):
dt-bindings: serial: Add MediaTek BTIF controller bindings
tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623
SoC
.../devicetree/bindings/serial/mtk-btif.txt | 26 +++
drivers/tty/serial/8250/8250_btif.c | 224 +++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 9 +
drivers/tty/serial/8250/Makefile | 1 +
4 files changed, 260 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
create mode 100644 drivers/tty/serial/8250/8250_btif.c
--
2.7.4
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-02 17:05 ` sean.wang
0 siblings, 0 replies; 27+ messages in thread
From: sean.wang at mediatek.com @ 2017-08-02 17:05 UTC (permalink / raw)
To: linux-arm-kernel
From: Sean Wang <sean.wang@mediatek.com>
This patchset introduces the support for MediaTek BTIF controller.
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module also called CONNSYS inside the SoC which could be
mostly found on those MediaTek SoCs with Bluetooth feature.
And the controller is made as being compatible with the 8250 register
layout so it tends to be integrated with existing 8250 core driver and
have no requirement for the modem configuration additionally such as the
baud rate calculation and assignment.
Sean Wang (2):
dt-bindings: serial: Add MediaTek BTIF controller bindings
tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623
SoC
.../devicetree/bindings/serial/mtk-btif.txt | 26 +++
drivers/tty/serial/8250/8250_btif.c | 224 +++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 9 +
drivers/tty/serial/8250/Makefile | 1 +
4 files changed, 260 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
create mode 100644 drivers/tty/serial/8250/8250_btif.c
--
2.7.4
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
2017-08-02 17:05 ` sean.wang
(?)
@ 2017-08-02 17:05 ` sean.wang
-1 siblings, 0 replies; 27+ messages in thread
From: sean.wang @ 2017-08-02 17:05 UTC (permalink / raw)
To: robh+dt, gregkh, jslaby, andriy.shevchenko, jan.kiszka,
heikki.krogerus, hpeter, vigneshr, matthias.bgg
Cc: devicetree, linux-mediatek, linux-serial, linux-arm-kernel,
linux-kernel, Sean Wang
From: Sean Wang <sean.wang@mediatek.com>
Document the devicetree bindings for MediaTek BTIF controller
which could be found on MT7622 and MT7623 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
.../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
1 file changed, 26 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
new file mode 100644
index 0000000..80c1f5a
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
@@ -0,0 +1,26 @@
+Device-Tree bindings for MediaTek BTIF controller found on those
+MediaTek SoCs with Bluetooth feature
+
+Required properties:
+- compatible: Should be one of:
+ - "mediatek,mt7622-btif" : for MT7622 SoC
+ - "mediatek,mt7623-btif" : for MT7623 SoC
+- reg: The base address of the BTIF register bank;
+- interrupts: A single interrupt specifier;
+- clocks: list of clock specifiers, corresponding to
+ entries in clock-names property;
+- clock-names: should contain "main" entries.
+
+Optional properties:
+- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
+ running on the loopback mode.
+
+Example:
+
+ btif: btif@1100c000 {
+ compatible = "mediatek,mt7623-btif";
+ reg = <0 0x1100c000 0 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_BTIF>;
+ clock-names = "main";
+ };
--
2.7.4
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
@ 2017-08-02 17:05 ` sean.wang
0 siblings, 0 replies; 27+ messages in thread
From: sean.wang @ 2017-08-02 17:05 UTC (permalink / raw)
To: robh+dt, gregkh, jslaby, andriy.shevchenko, jan.kiszka,
heikki.krogerus, hpeter, vigneshr, matthias.bgg
Cc: devicetree, Sean Wang, linux-kernel, linux-mediatek,
linux-serial, linux-arm-kernel
From: Sean Wang <sean.wang@mediatek.com>
Document the devicetree bindings for MediaTek BTIF controller
which could be found on MT7622 and MT7623 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
.../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
1 file changed, 26 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
new file mode 100644
index 0000000..80c1f5a
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
@@ -0,0 +1,26 @@
+Device-Tree bindings for MediaTek BTIF controller found on those
+MediaTek SoCs with Bluetooth feature
+
+Required properties:
+- compatible: Should be one of:
+ - "mediatek,mt7622-btif" : for MT7622 SoC
+ - "mediatek,mt7623-btif" : for MT7623 SoC
+- reg: The base address of the BTIF register bank;
+- interrupts: A single interrupt specifier;
+- clocks: list of clock specifiers, corresponding to
+ entries in clock-names property;
+- clock-names: should contain "main" entries.
+
+Optional properties:
+- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
+ running on the loopback mode.
+
+Example:
+
+ btif: btif@1100c000 {
+ compatible = "mediatek,mt7623-btif";
+ reg = <0 0x1100c000 0 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_BTIF>;
+ clock-names = "main";
+ };
--
2.7.4
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
@ 2017-08-02 17:05 ` sean.wang
0 siblings, 0 replies; 27+ messages in thread
From: sean.wang at mediatek.com @ 2017-08-02 17:05 UTC (permalink / raw)
To: linux-arm-kernel
From: Sean Wang <sean.wang@mediatek.com>
Document the devicetree bindings for MediaTek BTIF controller
which could be found on MT7622 and MT7623 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
.../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
1 file changed, 26 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
new file mode 100644
index 0000000..80c1f5a
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
@@ -0,0 +1,26 @@
+Device-Tree bindings for MediaTek BTIF controller found on those
+MediaTek SoCs with Bluetooth feature
+
+Required properties:
+- compatible: Should be one of:
+ - "mediatek,mt7622-btif" : for MT7622 SoC
+ - "mediatek,mt7623-btif" : for MT7623 SoC
+- reg: The base address of the BTIF register bank;
+- interrupts: A single interrupt specifier;
+- clocks: list of clock specifiers, corresponding to
+ entries in clock-names property;
+- clock-names: should contain "main" entries.
+
+Optional properties:
+- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
+ running on the loopback mode.
+
+Example:
+
+ btif: btif at 1100c000 {
+ compatible = "mediatek,mt7623-btif";
+ reg = <0 0x1100c000 0 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_BTIF>;
+ clock-names = "main";
+ };
--
2.7.4
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH 2/2] tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623 SoC
2017-08-02 17:05 ` sean.wang
(?)
@ 2017-08-02 17:05 ` sean.wang
-1 siblings, 0 replies; 27+ messages in thread
From: sean.wang @ 2017-08-02 17:05 UTC (permalink / raw)
To: robh+dt, gregkh, jslaby, andriy.shevchenko, jan.kiszka,
heikki.krogerus, hpeter, vigneshr, matthias.bgg
Cc: devicetree, linux-mediatek, linux-serial, linux-arm-kernel,
linux-kernel, Sean Wang
From: Sean Wang <sean.wang@mediatek.com>
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module also called CONNSYS inside the SoC which could be
mostly found on those MediaTek SoCs with Bluetooth feature.
And the controller is made as being compatible with the 8250 register
layout so it tends to be integrated with existing 8250 core driver and
have no requirement for the modem configuration additionally such as the
baud rate calculation and assignment.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
drivers/tty/serial/8250/8250_btif.c | 224 ++++++++++++++++++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 9 ++
drivers/tty/serial/8250/Makefile | 1 +
3 files changed, 234 insertions(+)
create mode 100644 drivers/tty/serial/8250/8250_btif.c
diff --git a/drivers/tty/serial/8250/8250_btif.c b/drivers/tty/serial/8250/8250_btif.c
new file mode 100644
index 0000000..06433e9
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_btif.c
@@ -0,0 +1,224 @@
+/*
+ * Driver for MediaTek BTIF Controller
+ *
+ * Copyright (C) 2017 Sean Wang <sean.wang@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_reg.h>
+
+#include "8250.h"
+
+#define MTK_BTIF_TRI_LVL 0x60
+#define BTIF_LOOP BIT(7)
+
+struct mtk_btif_data {
+ int line;
+ struct clk *main_clk;
+};
+
+static void
+mtk_btif_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
+{
+ if (!state)
+ pm_runtime_get_sync(port->dev);
+
+ serial8250_do_pm(port, state, old);
+
+ if (state)
+ pm_runtime_put_sync_suspend(port->dev);
+}
+
+static int mtk_btif_probe_of(struct platform_device *pdev, struct uart_port *p,
+ struct mtk_btif_data *data)
+{
+ int err;
+
+ data->main_clk = devm_clk_get(&pdev->dev, "main");
+ if (IS_ERR(data->main_clk)) {
+ dev_warn(&pdev->dev, "Can't get main clock\n");
+ return PTR_ERR(data->main_clk);
+ }
+
+ err = clk_prepare_enable(data->main_clk);
+ if (err) {
+ dev_warn(&pdev->dev, "Can't prepare main_clk\n");
+ clk_put(data->main_clk);
+ return err;
+ }
+
+ p->uartclk = clk_get_rate(data->main_clk);
+
+ return 0;
+}
+
+static int mtk_btif_runtime_suspend(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+
+ clk_disable_unprepare(data->main_clk);
+
+ return 0;
+}
+
+static int mtk_btif_runtime_resume(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+ int err;
+
+ err = clk_prepare_enable(data->main_clk);
+ if (err) {
+ dev_warn(dev, "Can't enable main clock\n");
+ return err;
+ }
+
+ return 0;
+}
+
+static int mtk_btif_probe(struct platform_device *pdev)
+{
+ struct uart_8250_port uart = {};
+ struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ struct mtk_btif_data *data;
+ int err;
+ u32 tmp;
+
+ if (!regs || !irq) {
+ dev_err(&pdev->dev, "no registers/irq defined\n");
+ return -EINVAL;
+ }
+
+ uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
+ resource_size(regs));
+ if (!uart.port.membase)
+ return -ENOMEM;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ if (pdev->dev.of_node) {
+ err = mtk_btif_probe_of(pdev, &uart.port, data);
+ if (err)
+ return err;
+ } else {
+ return -ENODEV;
+ }
+
+ spin_lock_init(&uart.port.lock);
+ uart.port.mapbase = regs->start;
+ uart.port.irq = irq->start;
+ uart.port.pm = mtk_btif_do_pm;
+ uart.port.type = PORT_8250;
+ uart.port.flags = UPF_FIXED_TYPE;
+ uart.port.dev = &pdev->dev;
+ uart.port.iotype = UPIO_MEM32;
+ uart.port.regshift = 2;
+ uart.port.private_data = data;
+
+ platform_set_drvdata(pdev, data);
+
+ pm_runtime_enable(&pdev->dev);
+
+ if (!pm_runtime_enabled(&pdev->dev)) {
+ err = mtk_btif_runtime_resume(&pdev->dev);
+ if (err)
+ return err;
+ }
+
+ if (of_property_read_bool(pdev->dev.of_node, "mediatek,loopback")) {
+ dev_info(&pdev->dev, "btif is entering loopback mode\n");
+ tmp = readl(uart.port.membase + MTK_BTIF_TRI_LVL);
+ tmp |= BTIF_LOOP;
+ writel(tmp, uart.port.membase + MTK_BTIF_TRI_LVL);
+ }
+
+ data->line = serial8250_register_8250_port(&uart);
+ if (data->line < 0)
+ return data->line;
+
+ return 0;
+}
+
+static int mtk_btif_remove(struct platform_device *pdev)
+{
+ struct mtk_btif_data *data = platform_get_drvdata(pdev);
+
+ pm_runtime_get_sync(&pdev->dev);
+
+ serial8250_unregister_port(data->line);
+
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+
+ if (!pm_runtime_status_suspended(&pdev->dev))
+ mtk_btif_runtime_suspend(&pdev->dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int mtk_btif_suspend(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+
+ serial8250_suspend_port(data->line);
+
+ return 0;
+}
+
+static int mtk_btif_resume(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+
+ serial8250_resume_port(data->line);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static const struct dev_pm_ops mtk_btif_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(mtk_btif_suspend, mtk_btif_resume)
+ SET_RUNTIME_PM_OPS(mtk_btif_runtime_suspend, mtk_btif_runtime_resume,
+ NULL)
+};
+
+static const struct of_device_id mtk_btif_of_match[] = {
+ { .compatible = "mediatek,mt7622-btif" },
+ { .compatible = "mediatek,mt7623-btif" },
+ { /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mtk_btif_of_match);
+
+static struct platform_driver mtk_btif_platform_driver = {
+ .driver = {
+ .name = "mediatek-btif",
+ .pm = &mtk_btif_pm_ops,
+ .of_match_table = mtk_btif_of_match,
+ },
+ .probe = mtk_btif_probe,
+ .remove = mtk_btif_remove,
+};
+module_platform_driver(mtk_btif_platform_driver);
+
+MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("MediaTek BTIF controller driver");
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index a1161ec..0e18cfc 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -403,6 +403,15 @@ config SERIAL_8250_MT6577
If you have a Mediatek based board and want to use the
serial port, say Y to this option. If unsure, say N.
+config SERIAL_8250_BTIF
+ tristate "MediaTek BTIF controller support"
+ depends on SERIAL_8250 && ARCH_MEDIATEK
+ help
+ Selecting this option will enable BTIF controller used by MediaTek
+ Bluetooth to communicate with internal hardware module inside the
+ SoC also being called CONNSYS which could be found on MediaTek SoCs
+ with Bluetooth feature, say Y to this option. If unsure, say N.
+
config SERIAL_8250_UNIPHIER
tristate "Support for UniPhier on-chip UART"
depends on SERIAL_8250
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index a44a99a..2fc73ce 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o
obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o
obj-$(CONFIG_SERIAL_8250_LPC18XX) += 8250_lpc18xx.o
obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o
+obj-$(CONFIG_SERIAL_8250_BTIF) += 8250_btif.o
obj-$(CONFIG_SERIAL_8250_UNIPHIER) += 8250_uniphier.o
obj-$(CONFIG_SERIAL_8250_INGENIC) += 8250_ingenic.o
obj-$(CONFIG_SERIAL_8250_LPSS) += 8250_lpss.o
--
2.7.4
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH 2/2] tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623 SoC
@ 2017-08-02 17:05 ` sean.wang
0 siblings, 0 replies; 27+ messages in thread
From: sean.wang @ 2017-08-02 17:05 UTC (permalink / raw)
To: robh+dt, gregkh, jslaby, andriy.shevchenko, jan.kiszka,
heikki.krogerus, hpeter, vigneshr, matthias.bgg
Cc: devicetree, linux-mediatek, linux-serial, linux-arm-kernel,
linux-kernel, Sean Wang
From: Sean Wang <sean.wang@mediatek.com>
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module also called CONNSYS inside the SoC which could be
mostly found on those MediaTek SoCs with Bluetooth feature.
And the controller is made as being compatible with the 8250 register
layout so it tends to be integrated with existing 8250 core driver and
have no requirement for the modem configuration additionally such as the
baud rate calculation and assignment.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
drivers/tty/serial/8250/8250_btif.c | 224 ++++++++++++++++++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 9 ++
drivers/tty/serial/8250/Makefile | 1 +
3 files changed, 234 insertions(+)
create mode 100644 drivers/tty/serial/8250/8250_btif.c
diff --git a/drivers/tty/serial/8250/8250_btif.c b/drivers/tty/serial/8250/8250_btif.c
new file mode 100644
index 0000000..06433e9
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_btif.c
@@ -0,0 +1,224 @@
+/*
+ * Driver for MediaTek BTIF Controller
+ *
+ * Copyright (C) 2017 Sean Wang <sean.wang@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_reg.h>
+
+#include "8250.h"
+
+#define MTK_BTIF_TRI_LVL 0x60
+#define BTIF_LOOP BIT(7)
+
+struct mtk_btif_data {
+ int line;
+ struct clk *main_clk;
+};
+
+static void
+mtk_btif_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
+{
+ if (!state)
+ pm_runtime_get_sync(port->dev);
+
+ serial8250_do_pm(port, state, old);
+
+ if (state)
+ pm_runtime_put_sync_suspend(port->dev);
+}
+
+static int mtk_btif_probe_of(struct platform_device *pdev, struct uart_port *p,
+ struct mtk_btif_data *data)
+{
+ int err;
+
+ data->main_clk = devm_clk_get(&pdev->dev, "main");
+ if (IS_ERR(data->main_clk)) {
+ dev_warn(&pdev->dev, "Can't get main clock\n");
+ return PTR_ERR(data->main_clk);
+ }
+
+ err = clk_prepare_enable(data->main_clk);
+ if (err) {
+ dev_warn(&pdev->dev, "Can't prepare main_clk\n");
+ clk_put(data->main_clk);
+ return err;
+ }
+
+ p->uartclk = clk_get_rate(data->main_clk);
+
+ return 0;
+}
+
+static int mtk_btif_runtime_suspend(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+
+ clk_disable_unprepare(data->main_clk);
+
+ return 0;
+}
+
+static int mtk_btif_runtime_resume(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+ int err;
+
+ err = clk_prepare_enable(data->main_clk);
+ if (err) {
+ dev_warn(dev, "Can't enable main clock\n");
+ return err;
+ }
+
+ return 0;
+}
+
+static int mtk_btif_probe(struct platform_device *pdev)
+{
+ struct uart_8250_port uart = {};
+ struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ struct mtk_btif_data *data;
+ int err;
+ u32 tmp;
+
+ if (!regs || !irq) {
+ dev_err(&pdev->dev, "no registers/irq defined\n");
+ return -EINVAL;
+ }
+
+ uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
+ resource_size(regs));
+ if (!uart.port.membase)
+ return -ENOMEM;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ if (pdev->dev.of_node) {
+ err = mtk_btif_probe_of(pdev, &uart.port, data);
+ if (err)
+ return err;
+ } else {
+ return -ENODEV;
+ }
+
+ spin_lock_init(&uart.port.lock);
+ uart.port.mapbase = regs->start;
+ uart.port.irq = irq->start;
+ uart.port.pm = mtk_btif_do_pm;
+ uart.port.type = PORT_8250;
+ uart.port.flags = UPF_FIXED_TYPE;
+ uart.port.dev = &pdev->dev;
+ uart.port.iotype = UPIO_MEM32;
+ uart.port.regshift = 2;
+ uart.port.private_data = data;
+
+ platform_set_drvdata(pdev, data);
+
+ pm_runtime_enable(&pdev->dev);
+
+ if (!pm_runtime_enabled(&pdev->dev)) {
+ err = mtk_btif_runtime_resume(&pdev->dev);
+ if (err)
+ return err;
+ }
+
+ if (of_property_read_bool(pdev->dev.of_node, "mediatek,loopback")) {
+ dev_info(&pdev->dev, "btif is entering loopback mode\n");
+ tmp = readl(uart.port.membase + MTK_BTIF_TRI_LVL);
+ tmp |= BTIF_LOOP;
+ writel(tmp, uart.port.membase + MTK_BTIF_TRI_LVL);
+ }
+
+ data->line = serial8250_register_8250_port(&uart);
+ if (data->line < 0)
+ return data->line;
+
+ return 0;
+}
+
+static int mtk_btif_remove(struct platform_device *pdev)
+{
+ struct mtk_btif_data *data = platform_get_drvdata(pdev);
+
+ pm_runtime_get_sync(&pdev->dev);
+
+ serial8250_unregister_port(data->line);
+
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+
+ if (!pm_runtime_status_suspended(&pdev->dev))
+ mtk_btif_runtime_suspend(&pdev->dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int mtk_btif_suspend(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+
+ serial8250_suspend_port(data->line);
+
+ return 0;
+}
+
+static int mtk_btif_resume(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+
+ serial8250_resume_port(data->line);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static const struct dev_pm_ops mtk_btif_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(mtk_btif_suspend, mtk_btif_resume)
+ SET_RUNTIME_PM_OPS(mtk_btif_runtime_suspend, mtk_btif_runtime_resume,
+ NULL)
+};
+
+static const struct of_device_id mtk_btif_of_match[] = {
+ { .compatible = "mediatek,mt7622-btif" },
+ { .compatible = "mediatek,mt7623-btif" },
+ { /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mtk_btif_of_match);
+
+static struct platform_driver mtk_btif_platform_driver = {
+ .driver = {
+ .name = "mediatek-btif",
+ .pm = &mtk_btif_pm_ops,
+ .of_match_table = mtk_btif_of_match,
+ },
+ .probe = mtk_btif_probe,
+ .remove = mtk_btif_remove,
+};
+module_platform_driver(mtk_btif_platform_driver);
+
+MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("MediaTek BTIF controller driver");
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index a1161ec..0e18cfc 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -403,6 +403,15 @@ config SERIAL_8250_MT6577
If you have a Mediatek based board and want to use the
serial port, say Y to this option. If unsure, say N.
+config SERIAL_8250_BTIF
+ tristate "MediaTek BTIF controller support"
+ depends on SERIAL_8250 && ARCH_MEDIATEK
+ help
+ Selecting this option will enable BTIF controller used by MediaTek
+ Bluetooth to communicate with internal hardware module inside the
+ SoC also being called CONNSYS which could be found on MediaTek SoCs
+ with Bluetooth feature, say Y to this option. If unsure, say N.
+
config SERIAL_8250_UNIPHIER
tristate "Support for UniPhier on-chip UART"
depends on SERIAL_8250
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index a44a99a..2fc73ce 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o
obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o
obj-$(CONFIG_SERIAL_8250_LPC18XX) += 8250_lpc18xx.o
obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o
+obj-$(CONFIG_SERIAL_8250_BTIF) += 8250_btif.o
obj-$(CONFIG_SERIAL_8250_UNIPHIER) += 8250_uniphier.o
obj-$(CONFIG_SERIAL_8250_INGENIC) += 8250_ingenic.o
obj-$(CONFIG_SERIAL_8250_LPSS) += 8250_lpss.o
--
2.7.4
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH 2/2] tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623 SoC
@ 2017-08-02 17:05 ` sean.wang
0 siblings, 0 replies; 27+ messages in thread
From: sean.wang at mediatek.com @ 2017-08-02 17:05 UTC (permalink / raw)
To: linux-arm-kernel
From: Sean Wang <sean.wang@mediatek.com>
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module also called CONNSYS inside the SoC which could be
mostly found on those MediaTek SoCs with Bluetooth feature.
And the controller is made as being compatible with the 8250 register
layout so it tends to be integrated with existing 8250 core driver and
have no requirement for the modem configuration additionally such as the
baud rate calculation and assignment.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
drivers/tty/serial/8250/8250_btif.c | 224 ++++++++++++++++++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 9 ++
drivers/tty/serial/8250/Makefile | 1 +
3 files changed, 234 insertions(+)
create mode 100644 drivers/tty/serial/8250/8250_btif.c
diff --git a/drivers/tty/serial/8250/8250_btif.c b/drivers/tty/serial/8250/8250_btif.c
new file mode 100644
index 0000000..06433e9
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_btif.c
@@ -0,0 +1,224 @@
+/*
+ * Driver for MediaTek BTIF Controller
+ *
+ * Copyright (C) 2017 Sean Wang <sean.wang@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_reg.h>
+
+#include "8250.h"
+
+#define MTK_BTIF_TRI_LVL 0x60
+#define BTIF_LOOP BIT(7)
+
+struct mtk_btif_data {
+ int line;
+ struct clk *main_clk;
+};
+
+static void
+mtk_btif_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
+{
+ if (!state)
+ pm_runtime_get_sync(port->dev);
+
+ serial8250_do_pm(port, state, old);
+
+ if (state)
+ pm_runtime_put_sync_suspend(port->dev);
+}
+
+static int mtk_btif_probe_of(struct platform_device *pdev, struct uart_port *p,
+ struct mtk_btif_data *data)
+{
+ int err;
+
+ data->main_clk = devm_clk_get(&pdev->dev, "main");
+ if (IS_ERR(data->main_clk)) {
+ dev_warn(&pdev->dev, "Can't get main clock\n");
+ return PTR_ERR(data->main_clk);
+ }
+
+ err = clk_prepare_enable(data->main_clk);
+ if (err) {
+ dev_warn(&pdev->dev, "Can't prepare main_clk\n");
+ clk_put(data->main_clk);
+ return err;
+ }
+
+ p->uartclk = clk_get_rate(data->main_clk);
+
+ return 0;
+}
+
+static int mtk_btif_runtime_suspend(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+
+ clk_disable_unprepare(data->main_clk);
+
+ return 0;
+}
+
+static int mtk_btif_runtime_resume(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+ int err;
+
+ err = clk_prepare_enable(data->main_clk);
+ if (err) {
+ dev_warn(dev, "Can't enable main clock\n");
+ return err;
+ }
+
+ return 0;
+}
+
+static int mtk_btif_probe(struct platform_device *pdev)
+{
+ struct uart_8250_port uart = {};
+ struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ struct mtk_btif_data *data;
+ int err;
+ u32 tmp;
+
+ if (!regs || !irq) {
+ dev_err(&pdev->dev, "no registers/irq defined\n");
+ return -EINVAL;
+ }
+
+ uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
+ resource_size(regs));
+ if (!uart.port.membase)
+ return -ENOMEM;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ if (pdev->dev.of_node) {
+ err = mtk_btif_probe_of(pdev, &uart.port, data);
+ if (err)
+ return err;
+ } else {
+ return -ENODEV;
+ }
+
+ spin_lock_init(&uart.port.lock);
+ uart.port.mapbase = regs->start;
+ uart.port.irq = irq->start;
+ uart.port.pm = mtk_btif_do_pm;
+ uart.port.type = PORT_8250;
+ uart.port.flags = UPF_FIXED_TYPE;
+ uart.port.dev = &pdev->dev;
+ uart.port.iotype = UPIO_MEM32;
+ uart.port.regshift = 2;
+ uart.port.private_data = data;
+
+ platform_set_drvdata(pdev, data);
+
+ pm_runtime_enable(&pdev->dev);
+
+ if (!pm_runtime_enabled(&pdev->dev)) {
+ err = mtk_btif_runtime_resume(&pdev->dev);
+ if (err)
+ return err;
+ }
+
+ if (of_property_read_bool(pdev->dev.of_node, "mediatek,loopback")) {
+ dev_info(&pdev->dev, "btif is entering loopback mode\n");
+ tmp = readl(uart.port.membase + MTK_BTIF_TRI_LVL);
+ tmp |= BTIF_LOOP;
+ writel(tmp, uart.port.membase + MTK_BTIF_TRI_LVL);
+ }
+
+ data->line = serial8250_register_8250_port(&uart);
+ if (data->line < 0)
+ return data->line;
+
+ return 0;
+}
+
+static int mtk_btif_remove(struct platform_device *pdev)
+{
+ struct mtk_btif_data *data = platform_get_drvdata(pdev);
+
+ pm_runtime_get_sync(&pdev->dev);
+
+ serial8250_unregister_port(data->line);
+
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+
+ if (!pm_runtime_status_suspended(&pdev->dev))
+ mtk_btif_runtime_suspend(&pdev->dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int mtk_btif_suspend(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+
+ serial8250_suspend_port(data->line);
+
+ return 0;
+}
+
+static int mtk_btif_resume(struct device *dev)
+{
+ struct mtk_btif_data *data = dev_get_drvdata(dev);
+
+ serial8250_resume_port(data->line);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static const struct dev_pm_ops mtk_btif_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(mtk_btif_suspend, mtk_btif_resume)
+ SET_RUNTIME_PM_OPS(mtk_btif_runtime_suspend, mtk_btif_runtime_resume,
+ NULL)
+};
+
+static const struct of_device_id mtk_btif_of_match[] = {
+ { .compatible = "mediatek,mt7622-btif" },
+ { .compatible = "mediatek,mt7623-btif" },
+ { /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mtk_btif_of_match);
+
+static struct platform_driver mtk_btif_platform_driver = {
+ .driver = {
+ .name = "mediatek-btif",
+ .pm = &mtk_btif_pm_ops,
+ .of_match_table = mtk_btif_of_match,
+ },
+ .probe = mtk_btif_probe,
+ .remove = mtk_btif_remove,
+};
+module_platform_driver(mtk_btif_platform_driver);
+
+MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("MediaTek BTIF controller driver");
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index a1161ec..0e18cfc 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -403,6 +403,15 @@ config SERIAL_8250_MT6577
If you have a Mediatek based board and want to use the
serial port, say Y to this option. If unsure, say N.
+config SERIAL_8250_BTIF
+ tristate "MediaTek BTIF controller support"
+ depends on SERIAL_8250 && ARCH_MEDIATEK
+ help
+ Selecting this option will enable BTIF controller used by MediaTek
+ Bluetooth to communicate with internal hardware module inside the
+ SoC also being called CONNSYS which could be found on MediaTek SoCs
+ with Bluetooth feature, say Y to this option. If unsure, say N.
+
config SERIAL_8250_UNIPHIER
tristate "Support for UniPhier on-chip UART"
depends on SERIAL_8250
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index a44a99a..2fc73ce 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o
obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o
obj-$(CONFIG_SERIAL_8250_LPC18XX) += 8250_lpc18xx.o
obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o
+obj-$(CONFIG_SERIAL_8250_BTIF) += 8250_btif.o
obj-$(CONFIG_SERIAL_8250_UNIPHIER) += 8250_uniphier.o
obj-$(CONFIG_SERIAL_8250_INGENIC) += 8250_ingenic.o
obj-$(CONFIG_SERIAL_8250_LPSS) += 8250_lpss.o
--
2.7.4
^ permalink raw reply related [flat|nested] 27+ messages in thread
* Re: [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
2017-08-02 17:05 ` sean.wang
@ 2017-08-02 17:14 ` Andy Shevchenko
-1 siblings, 0 replies; 27+ messages in thread
From: Andy Shevchenko @ 2017-08-02 17:14 UTC (permalink / raw)
To: sean.wang, robh+dt, gregkh, jslaby, jan.kiszka, heikki.krogerus,
hpeter, vigneshr, matthias.bgg
Cc: devicetree, linux-mediatek, linux-serial, linux-arm-kernel, linux-kernel
On Thu, 2017-08-03 at 01:05 +0800, sean.wang@mediatek.com wrote:
> From: Sean Wang <sean.wang@mediatek.com>
>
> This patchset introduces the support for MediaTek BTIF controller.
>
> MediaTek BTIF controller is the serial interface similar to UART but
> it
> works only as the digital device which is mainly used to communicate
> with
> the connectivity module also called CONNSYS inside the SoC which could
> be
> mostly found on those MediaTek SoCs with Bluetooth feature.
>
> And the controller is made as being compatible with the 8250 register
> layout so it tends to be integrated with existing 8250 core driver and
> have no requirement for the modem configuration additionally such as
> the
> baud rate calculation and assignment.
Why it requires a separate driver?
8250_of is for DT enabled drivers.
>
> Sean Wang (2):
> dt-bindings: serial: Add MediaTek BTIF controller bindings
> tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623
> SoC
>
> .../devicetree/bindings/serial/mtk-btif.txt | 26 +++
> drivers/tty/serial/8250/8250_btif.c | 224
> +++++++++++++++++++++
> drivers/tty/serial/8250/Kconfig | 9 +
> drivers/tty/serial/8250/Makefile | 1 +
> 4 files changed, 260 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/serial/mtk-
> btif.txt
> create mode 100644 drivers/tty/serial/8250/8250_btif.c
>
--
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Finland Oy
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-02 17:14 ` Andy Shevchenko
0 siblings, 0 replies; 27+ messages in thread
From: Andy Shevchenko @ 2017-08-02 17:14 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, 2017-08-03 at 01:05 +0800, sean.wang at mediatek.com wrote:
> From: Sean Wang <sean.wang@mediatek.com>
>
> This patchset introduces the support for MediaTek BTIF controller.
>
> MediaTek BTIF controller is the serial interface similar to UART but
> it
> works only as the digital device which is mainly used to communicate
> with
> the connectivity module also called CONNSYS inside the SoC which could
> be
> mostly found on those MediaTek SoCs with Bluetooth feature.
>
> And the controller is made as being compatible with the 8250 register
> layout so it tends to be integrated with existing 8250 core driver and
> have no requirement for the modem configuration additionally such as
> the
> baud rate calculation and assignment.
Why it requires a separate driver?
8250_of is for DT enabled drivers.
>
> Sean Wang (2):
> ? dt-bindings: serial: Add MediaTek BTIF controller bindings
> ? tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623
> ????SoC
>
> ?.../devicetree/bindings/serial/mtk-btif.txt????????|??26 +++
> ?drivers/tty/serial/8250/8250_btif.c????????????????| 224
> +++++++++++++++++++++
> ?drivers/tty/serial/8250/Kconfig????????????????????|???9 +
> ?drivers/tty/serial/8250/Makefile???????????????????|???1 +
> ?4 files changed, 260 insertions(+)
> ?create mode 100644 Documentation/devicetree/bindings/serial/mtk-
> btif.txt
> ?create mode 100644 drivers/tty/serial/8250/8250_btif.c
>
--
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Finland Oy
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-02 17:37 ` Sean Wang
0 siblings, 0 replies; 27+ messages in thread
From: Sean Wang @ 2017-08-02 17:37 UTC (permalink / raw)
To: Andy Shevchenko
Cc: robh+dt, gregkh, jslaby, jan.kiszka, heikki.krogerus, hpeter,
vigneshr, matthias.bgg, devicetree, linux-mediatek, linux-serial,
linux-arm-kernel, linux-kernel
On Wed, 2017-08-02 at 20:14 +0300, Andy Shevchenko wrote:
> On Thu, 2017-08-03 at 01:05 +0800, sean.wang@mediatek.com wrote:
> > From: Sean Wang <sean.wang@mediatek.com>
> >
> > This patchset introduces the support for MediaTek BTIF controller.
> >
> > MediaTek BTIF controller is the serial interface similar to UART but
> > it
> > works only as the digital device which is mainly used to communicate
> > with
> > the connectivity module also called CONNSYS inside the SoC which could
> > be
> > mostly found on those MediaTek SoCs with Bluetooth feature.
> >
> > And the controller is made as being compatible with the 8250 register
> > layout so it tends to be integrated with existing 8250 core driver and
> > have no requirement for the modem configuration additionally such as
> > the
> > baud rate calculation and assignment.
>
>
> Why it requires a separate driver?
>
> 8250_of is for DT enabled drivers.
>
Hi, Andy
thanks for your information
the hardware is not completely identical to 8250 device,
it has extra registers belonged to platform control such as internal
loopback, dma disable/enable, sleep/wakeup setup and so on, so I create
it as a separate driver.
Sean
> >
> > Sean Wang (2):
> > dt-bindings: serial: Add MediaTek BTIF controller bindings
> > tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623
> > SoC
> >
> > .../devicetree/bindings/serial/mtk-btif.txt | 26 +++
> > drivers/tty/serial/8250/8250_btif.c | 224
> > +++++++++++++++++++++
> > drivers/tty/serial/8250/Kconfig | 9 +
> > drivers/tty/serial/8250/Makefile | 1 +
> > 4 files changed, 260 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/serial/mtk-
> > btif.txt
> > create mode 100644 drivers/tty/serial/8250/8250_btif.c
> >
>
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-02 17:37 ` Sean Wang
0 siblings, 0 replies; 27+ messages in thread
From: Sean Wang @ 2017-08-02 17:37 UTC (permalink / raw)
To: Andy Shevchenko
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r, jslaby-IBi9RG/b67k,
jan.kiszka-kv7WeFo6aLtBDgjK7y7TUQ,
heikki.krogerus-VuQAYsv1563Yd54FQh9/CA,
hpeter-Re5JQEeQqe8AvxtiuMwx3w, vigneshr-l0cyMroinI0,
matthias.bgg-Re5JQEeQqe8AvxtiuMwx3w,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-serial-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On Wed, 2017-08-02 at 20:14 +0300, Andy Shevchenko wrote:
> On Thu, 2017-08-03 at 01:05 +0800, sean.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org wrote:
> > From: Sean Wang <sean.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> >
> > This patchset introduces the support for MediaTek BTIF controller.
> >
> > MediaTek BTIF controller is the serial interface similar to UART but
> > it
> > works only as the digital device which is mainly used to communicate
> > with
> > the connectivity module also called CONNSYS inside the SoC which could
> > be
> > mostly found on those MediaTek SoCs with Bluetooth feature.
> >
> > And the controller is made as being compatible with the 8250 register
> > layout so it tends to be integrated with existing 8250 core driver and
> > have no requirement for the modem configuration additionally such as
> > the
> > baud rate calculation and assignment.
>
>
> Why it requires a separate driver?
>
> 8250_of is for DT enabled drivers.
>
Hi, Andy
thanks for your information
the hardware is not completely identical to 8250 device,
it has extra registers belonged to platform control such as internal
loopback, dma disable/enable, sleep/wakeup setup and so on, so I create
it as a separate driver.
Sean
> >
> > Sean Wang (2):
> > dt-bindings: serial: Add MediaTek BTIF controller bindings
> > tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623
> > SoC
> >
> > .../devicetree/bindings/serial/mtk-btif.txt | 26 +++
> > drivers/tty/serial/8250/8250_btif.c | 224
> > +++++++++++++++++++++
> > drivers/tty/serial/8250/Kconfig | 9 +
> > drivers/tty/serial/8250/Makefile | 1 +
> > 4 files changed, 260 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/serial/mtk-
> > btif.txt
> > create mode 100644 drivers/tty/serial/8250/8250_btif.c
> >
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-02 17:37 ` Sean Wang
0 siblings, 0 replies; 27+ messages in thread
From: Sean Wang @ 2017-08-02 17:37 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, 2017-08-02 at 20:14 +0300, Andy Shevchenko wrote:
> On Thu, 2017-08-03 at 01:05 +0800, sean.wang at mediatek.com wrote:
> > From: Sean Wang <sean.wang@mediatek.com>
> >
> > This patchset introduces the support for MediaTek BTIF controller.
> >
> > MediaTek BTIF controller is the serial interface similar to UART but
> > it
> > works only as the digital device which is mainly used to communicate
> > with
> > the connectivity module also called CONNSYS inside the SoC which could
> > be
> > mostly found on those MediaTek SoCs with Bluetooth feature.
> >
> > And the controller is made as being compatible with the 8250 register
> > layout so it tends to be integrated with existing 8250 core driver and
> > have no requirement for the modem configuration additionally such as
> > the
> > baud rate calculation and assignment.
>
>
> Why it requires a separate driver?
>
> 8250_of is for DT enabled drivers.
>
Hi, Andy
thanks for your information
the hardware is not completely identical to 8250 device,
it has extra registers belonged to platform control such as internal
loopback, dma disable/enable, sleep/wakeup setup and so on, so I create
it as a separate driver.
Sean
> >
> > Sean Wang (2):
> > dt-bindings: serial: Add MediaTek BTIF controller bindings
> > tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623
> > SoC
> >
> > .../devicetree/bindings/serial/mtk-btif.txt | 26 +++
> > drivers/tty/serial/8250/8250_btif.c | 224
> > +++++++++++++++++++++
> > drivers/tty/serial/8250/Kconfig | 9 +
> > drivers/tty/serial/8250/Makefile | 1 +
> > 4 files changed, 260 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/serial/mtk-
> > btif.txt
> > create mode 100644 drivers/tty/serial/8250/8250_btif.c
> >
>
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
2017-08-02 17:37 ` Sean Wang
(?)
@ 2017-08-02 18:02 ` Andy Shevchenko
-1 siblings, 0 replies; 27+ messages in thread
From: Andy Shevchenko @ 2017-08-02 18:02 UTC (permalink / raw)
To: Sean Wang, arnd.bergmann
Cc: robh+dt, gregkh, jslaby, jan.kiszka, heikki.krogerus, hpeter,
vigneshr, matthias.bgg, devicetree, linux-mediatek, linux-serial,
linux-arm-kernel, linux-kernel
On Thu, 2017-08-03 at 01:37 +0800, Sean Wang wrote:
> On Wed, 2017-08-02 at 20:14 +0300, Andy Shevchenko wrote:
> > On Thu, 2017-08-03 at 01:05 +0800, sean.wang@mediatek.com wrote:
> > > From: Sean Wang <sean.wang@mediatek.com>
> > >
> > > This patchset introduces the support for MediaTek BTIF controller.
> > >
> > > MediaTek BTIF controller is the serial interface similar to UART
> > > but
> > > it
> > > works only as the digital device which is mainly used to
> > > communicate
> > > with
> > > the connectivity module also called CONNSYS inside the SoC which
> > > could
> > > be
> > > mostly found on those MediaTek SoCs with Bluetooth feature.
> > >
> > > And the controller is made as being compatible with the 8250
> > > register
> > > layout so it tends to be integrated with existing 8250 core driver
> > > and
> > > have no requirement for the modem configuration additionally such
> > > as
> > > the
> > > baud rate calculation and assignment.
+Cc: Arnd.
> > Why it requires a separate driver?
> >
> > 8250_of is for DT enabled drivers.
> >
>
> Hi, Andy
>
> thanks for your information
>
> the hardware is not completely identical to 8250 device,
> it has extra registers belonged to platform control such as internal
> loopback, dma disable/enable, sleep/wakeup setup and so on, so I
> create
> it as a separate driver.
Over all 200+ LOCs I didn't see any of the above except loopback, which
is one property that can be easily added to 8250_of.c.
Moreover, if you have more code coming I would suggest you to split
8250_of to library and driver parts and re-use stuff from there.
Arnd, what is your opinion about new 8250 OF based drivers?
--
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Finland Oy
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-02 18:02 ` Andy Shevchenko
0 siblings, 0 replies; 27+ messages in thread
From: Andy Shevchenko @ 2017-08-02 18:02 UTC (permalink / raw)
To: Sean Wang, arnd.bergmann
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r, jslaby-IBi9RG/b67k,
jan.kiszka-kv7WeFo6aLtBDgjK7y7TUQ,
heikki.krogerus-VuQAYsv1563Yd54FQh9/CA,
hpeter-Re5JQEeQqe8AvxtiuMwx3w, vigneshr-l0cyMroinI0,
matthias.bgg-Re5JQEeQqe8AvxtiuMwx3w,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-serial-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On Thu, 2017-08-03 at 01:37 +0800, Sean Wang wrote:
> On Wed, 2017-08-02 at 20:14 +0300, Andy Shevchenko wrote:
> > On Thu, 2017-08-03 at 01:05 +0800, sean.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org wrote:
> > > From: Sean Wang <sean.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> > >
> > > This patchset introduces the support for MediaTek BTIF controller.
> > >
> > > MediaTek BTIF controller is the serial interface similar to UART
> > > but
> > > it
> > > works only as the digital device which is mainly used to
> > > communicate
> > > with
> > > the connectivity module also called CONNSYS inside the SoC which
> > > could
> > > be
> > > mostly found on those MediaTek SoCs with Bluetooth feature.
> > >
> > > And the controller is made as being compatible with the 8250
> > > register
> > > layout so it tends to be integrated with existing 8250 core driver
> > > and
> > > have no requirement for the modem configuration additionally such
> > > as
> > > the
> > > baud rate calculation and assignment.
+Cc: Arnd.
> > Why it requires a separate driver?
> >
> > 8250_of is for DT enabled drivers.
> >
>
> Hi, Andy
>
> thanks for your information
>
> the hardware is not completely identical to 8250 device,
> it has extra registers belonged to platform control such as internal
> loopback, dma disable/enable, sleep/wakeup setup and so on, so I
> create
> it as a separate driver.
Over all 200+ LOCs I didn't see any of the above except loopback, which
is one property that can be easily added to 8250_of.c.
Moreover, if you have more code coming I would suggest you to split
8250_of to library and driver parts and re-use stuff from there.
Arnd, what is your opinion about new 8250 OF based drivers?
--
Andy Shevchenko <andriy.shevchenko-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
Intel Finland Oy
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-02 18:02 ` Andy Shevchenko
0 siblings, 0 replies; 27+ messages in thread
From: Andy Shevchenko @ 2017-08-02 18:02 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, 2017-08-03 at 01:37 +0800, Sean Wang wrote:
> On Wed, 2017-08-02 at 20:14 +0300, Andy Shevchenko wrote:
> > On Thu, 2017-08-03 at 01:05 +0800, sean.wang at mediatek.com wrote:
> > > From: Sean Wang <sean.wang@mediatek.com>
> > >
> > > This patchset introduces the support for MediaTek BTIF controller.
> > >
> > > MediaTek BTIF controller is the serial interface similar to UART
> > > but
> > > it
> > > works only as the digital device which is mainly used to
> > > communicate
> > > with
> > > the connectivity module also called CONNSYS inside the SoC which
> > > could
> > > be
> > > mostly found on those MediaTek SoCs with Bluetooth feature.
> > >
> > > And the controller is made as being compatible with the 8250
> > > register
> > > layout so it tends to be integrated with existing 8250 core driver
> > > and
> > > have no requirement for the modem configuration additionally such
> > > as
> > > the
> > > baud rate calculation and assignment.
+Cc: Arnd.
> > Why it requires a separate driver?
> >
> > 8250_of is for DT enabled drivers.
> >
>
> Hi, Andy
>
> thanks for your information
>
> the hardware is not completely identical to 8250 device,?
> it has extra registers belonged to platform control such as internal
> loopback, dma disable/enable, sleep/wakeup setup and so on, so I
> create
> it as a separate driver.
Over all 200+ LOCs I didn't see any of the above except loopback, which
is one property that can be easily added to 8250_of.c.
Moreover, if you have more code coming I would suggest you to split
8250_of to library and driver parts and re-use stuff from there.
Arnd, what is your opinion about new 8250 OF based drivers?
--
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Finland Oy
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
2017-08-02 18:02 ` Andy Shevchenko
@ 2017-08-03 3:18 ` Sean Wang
-1 siblings, 0 replies; 27+ messages in thread
From: Sean Wang @ 2017-08-03 3:18 UTC (permalink / raw)
To: Andy Shevchenko
Cc: devicetree, heikki.krogerus, vigneshr, gregkh, jslaby, hpeter,
linux-kernel, robh+dt, linux-mediatek, linux-serial, jan.kiszka,
matthias.bgg, arnd.bergmann, linux-arm-kernel
On Wed, 2017-08-02 at 21:02 +0300, Andy Shevchenko wrote:
> On Thu, 2017-08-03 at 01:37 +0800, Sean Wang wrote:
> > On Wed, 2017-08-02 at 20:14 +0300, Andy Shevchenko wrote:
> > > On Thu, 2017-08-03 at 01:05 +0800, sean.wang@mediatek.com wrote:
> > > > From: Sean Wang <sean.wang@mediatek.com>
> > > >
> > > > This patchset introduces the support for MediaTek BTIF controller.
> > > >
> > > > MediaTek BTIF controller is the serial interface similar to UART
> > > > but
> > > > it
> > > > works only as the digital device which is mainly used to
> > > > communicate
> > > > with
> > > > the connectivity module also called CONNSYS inside the SoC which
> > > > could
> > > > be
> > > > mostly found on those MediaTek SoCs with Bluetooth feature.
> > > >
> > > > And the controller is made as being compatible with the 8250
> > > > register
> > > > layout so it tends to be integrated with existing 8250 core driver
> > > > and
> > > > have no requirement for the modem configuration additionally such
> > > > as
> > > > the
> > > > baud rate calculation and assignment.
>
> +Cc: Arnd.
>
> > > Why it requires a separate driver?
> > >
> > > 8250_of is for DT enabled drivers.
> > >
> >
> > Hi, Andy
> >
> > thanks for your information
> >
> > the hardware is not completely identical to 8250 device,
> > it has extra registers belonged to platform control such as internal
> > loopback, dma disable/enable, sleep/wakeup setup and so on, so I
> > create
> > it as a separate driver.
>
> Over all 200+ LOCs I didn't see any of the above except loopback, which
> is one property that can be easily added to 8250_of.c.
>
> Moreover, if you have more code coming I would suggest you to split
> 8250_of to library and driver parts and re-use stuff from there.
>
> Arnd, what is your opinion about new 8250 OF based drivers?
>
Hi, Andy
many thanks for the detailed guidance.
I will turn into reusing 8250 OF stuff in the next version and look
forward to any idea from Arnd how to do with 8250 OF driver to add
specific programming/data for those devices using 8250 OF.
Sean
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller
@ 2017-08-03 3:18 ` Sean Wang
0 siblings, 0 replies; 27+ messages in thread
From: Sean Wang @ 2017-08-03 3:18 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, 2017-08-02 at 21:02 +0300, Andy Shevchenko wrote:
> On Thu, 2017-08-03 at 01:37 +0800, Sean Wang wrote:
> > On Wed, 2017-08-02 at 20:14 +0300, Andy Shevchenko wrote:
> > > On Thu, 2017-08-03 at 01:05 +0800, sean.wang at mediatek.com wrote:
> > > > From: Sean Wang <sean.wang@mediatek.com>
> > > >
> > > > This patchset introduces the support for MediaTek BTIF controller.
> > > >
> > > > MediaTek BTIF controller is the serial interface similar to UART
> > > > but
> > > > it
> > > > works only as the digital device which is mainly used to
> > > > communicate
> > > > with
> > > > the connectivity module also called CONNSYS inside the SoC which
> > > > could
> > > > be
> > > > mostly found on those MediaTek SoCs with Bluetooth feature.
> > > >
> > > > And the controller is made as being compatible with the 8250
> > > > register
> > > > layout so it tends to be integrated with existing 8250 core driver
> > > > and
> > > > have no requirement for the modem configuration additionally such
> > > > as
> > > > the
> > > > baud rate calculation and assignment.
>
> +Cc: Arnd.
>
> > > Why it requires a separate driver?
> > >
> > > 8250_of is for DT enabled drivers.
> > >
> >
> > Hi, Andy
> >
> > thanks for your information
> >
> > the hardware is not completely identical to 8250 device,
> > it has extra registers belonged to platform control such as internal
> > loopback, dma disable/enable, sleep/wakeup setup and so on, so I
> > create
> > it as a separate driver.
>
> Over all 200+ LOCs I didn't see any of the above except loopback, which
> is one property that can be easily added to 8250_of.c.
>
> Moreover, if you have more code coming I would suggest you to split
> 8250_of to library and driver parts and re-use stuff from there.
>
> Arnd, what is your opinion about new 8250 OF based drivers?
>
Hi, Andy
many thanks for the detailed guidance.
I will turn into reusing 8250 OF stuff in the next version and look
forward to any idea from Arnd how to do with 8250 OF driver to add
specific programming/data for those devices using 8250 OF.
Sean
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
2017-08-02 17:05 ` sean.wang
@ 2017-08-10 16:27 ` Rob Herring
-1 siblings, 0 replies; 27+ messages in thread
From: Rob Herring @ 2017-08-10 16:27 UTC (permalink / raw)
To: sean.wang
Cc: gregkh, jslaby, andriy.shevchenko, jan.kiszka, heikki.krogerus,
hpeter, vigneshr, matthias.bgg, devicetree, linux-mediatek,
linux-serial, linux-arm-kernel, linux-kernel
On Thu, Aug 03, 2017 at 01:05:22AM +0800, sean.wang@mediatek.com wrote:
> From: Sean Wang <sean.wang@mediatek.com>
>
> Document the devicetree bindings for MediaTek BTIF controller
> which could be found on MT7622 and MT7623 SoC.
>
> Signed-off-by: Sean Wang <sean.wang@mediatek.com>
> ---
> .../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
> 1 file changed, 26 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
>
> diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> new file mode 100644
> index 0000000..80c1f5a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> @@ -0,0 +1,26 @@
> +Device-Tree bindings for MediaTek BTIF controller found on those
> +MediaTek SoCs with Bluetooth feature
> +
> +Required properties:
> +- compatible: Should be one of:
> + - "mediatek,mt7622-btif" : for MT7622 SoC
> + - "mediatek,mt7623-btif" : for MT7623 SoC
> +- reg: The base address of the BTIF register bank;
> +- interrupts: A single interrupt specifier;
> +- clocks: list of clock specifiers, corresponding to
> + entries in clock-names property;
> +- clock-names: should contain "main" entries.
> +
> +Optional properties:
> +- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
> + running on the loopback mode.
I don't think this belongs in DT, but should be a module param or sysfs
control.
> +
> +Example:
> +
> + btif: btif@1100c000 {
bluetooth@...
> + compatible = "mediatek,mt7623-btif";
> + reg = <0 0x1100c000 0 0x1000>;
> + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&pericfg CLK_PERI_BTIF>;
> + clock-names = "main";
> + };
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
@ 2017-08-10 16:27 ` Rob Herring
0 siblings, 0 replies; 27+ messages in thread
From: Rob Herring @ 2017-08-10 16:27 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Aug 03, 2017 at 01:05:22AM +0800, sean.wang at mediatek.com wrote:
> From: Sean Wang <sean.wang@mediatek.com>
>
> Document the devicetree bindings for MediaTek BTIF controller
> which could be found on MT7622 and MT7623 SoC.
>
> Signed-off-by: Sean Wang <sean.wang@mediatek.com>
> ---
> .../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
> 1 file changed, 26 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
>
> diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> new file mode 100644
> index 0000000..80c1f5a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> @@ -0,0 +1,26 @@
> +Device-Tree bindings for MediaTek BTIF controller found on those
> +MediaTek SoCs with Bluetooth feature
> +
> +Required properties:
> +- compatible: Should be one of:
> + - "mediatek,mt7622-btif" : for MT7622 SoC
> + - "mediatek,mt7623-btif" : for MT7623 SoC
> +- reg: The base address of the BTIF register bank;
> +- interrupts: A single interrupt specifier;
> +- clocks: list of clock specifiers, corresponding to
> + entries in clock-names property;
> +- clock-names: should contain "main" entries.
> +
> +Optional properties:
> +- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
> + running on the loopback mode.
I don't think this belongs in DT, but should be a module param or sysfs
control.
> +
> +Example:
> +
> + btif: btif at 1100c000 {
bluetooth at ...
> + compatible = "mediatek,mt7623-btif";
> + reg = <0 0x1100c000 0 0x1000>;
> + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&pericfg CLK_PERI_BTIF>;
> + clock-names = "main";
> + };
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
2017-08-10 16:27 ` Rob Herring
(?)
@ 2017-08-11 2:53 ` Sean Wang
-1 siblings, 0 replies; 27+ messages in thread
From: Sean Wang @ 2017-08-11 2:53 UTC (permalink / raw)
To: Rob Herring
Cc: gregkh, jslaby, andriy.shevchenko, jan.kiszka, heikki.krogerus,
hpeter, vigneshr, matthias.bgg, devicetree, linux-mediatek,
linux-serial, linux-arm-kernel, linux-kernel
On Thu, 2017-08-10 at 11:27 -0500, Rob Herring wrote:
> On Thu, Aug 03, 2017 at 01:05:22AM +0800, sean.wang@mediatek.com wrote:
> > From: Sean Wang <sean.wang@mediatek.com>
> >
> > Document the devicetree bindings for MediaTek BTIF controller
> > which could be found on MT7622 and MT7623 SoC.
> >
> > Signed-off-by: Sean Wang <sean.wang@mediatek.com>
> > ---
> > .../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
> > 1 file changed, 26 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
> >
> > diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> > new file mode 100644
> > index 0000000..80c1f5a
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> > @@ -0,0 +1,26 @@
> > +Device-Tree bindings for MediaTek BTIF controller found on those
> > +MediaTek SoCs with Bluetooth feature
> > +
> > +Required properties:
> > +- compatible: Should be one of:
> > + - "mediatek,mt7622-btif" : for MT7622 SoC
> > + - "mediatek,mt7623-btif" : for MT7623 SoC
> > +- reg: The base address of the BTIF register bank;
> > +- interrupts: A single interrupt specifier;
> > +- clocks: list of clock specifiers, corresponding to
> > + entries in clock-names property;
> > +- clock-names: should contain "main" entries.
> > +
> > +Optional properties:
> > +- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
> > + running on the loopback mode.
>
> I don't think this belongs in DT, but should be a module param or sysfs
> control.
>
the loopback actually is one of hardware setups so i add it as one
property in the dt or could you kindly guide me how to make judgment
accurately for listing those changes as either dt or a module param?
> > +
> > +Example:
> > +
> > + btif: btif@1100c000 {
>
> bluetooth@...
>
btif not bluetooth, which is just the interface hardware allowing the
the main processor communicating with the bluetooth hardware built in
the SoC, and is really like to the uart used by legacy bluetooth.
So i will add bluetooth as the another node.
> > + compatible = "mediatek,mt7623-btif";
> > + reg = <0 0x1100c000 0 0x1000>;
> > + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
> > + clocks = <&pericfg CLK_PERI_BTIF>;
> > + clock-names = "main";
> > + };
> > --
> > 2.7.4
> >
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
@ 2017-08-11 2:53 ` Sean Wang
0 siblings, 0 replies; 27+ messages in thread
From: Sean Wang @ 2017-08-11 2:53 UTC (permalink / raw)
To: Rob Herring
Cc: gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r, jslaby-IBi9RG/b67k,
andriy.shevchenko-VuQAYsv1563Yd54FQh9/CA,
jan.kiszka-kv7WeFo6aLtBDgjK7y7TUQ,
heikki.krogerus-VuQAYsv1563Yd54FQh9/CA,
hpeter-Re5JQEeQqe8AvxtiuMwx3w, vigneshr-l0cyMroinI0,
matthias.bgg-Re5JQEeQqe8AvxtiuMwx3w,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-serial-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On Thu, 2017-08-10 at 11:27 -0500, Rob Herring wrote:
> On Thu, Aug 03, 2017 at 01:05:22AM +0800, sean.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org wrote:
> > From: Sean Wang <sean.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> >
> > Document the devicetree bindings for MediaTek BTIF controller
> > which could be found on MT7622 and MT7623 SoC.
> >
> > Signed-off-by: Sean Wang <sean.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> > ---
> > .../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
> > 1 file changed, 26 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
> >
> > diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> > new file mode 100644
> > index 0000000..80c1f5a
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> > @@ -0,0 +1,26 @@
> > +Device-Tree bindings for MediaTek BTIF controller found on those
> > +MediaTek SoCs with Bluetooth feature
> > +
> > +Required properties:
> > +- compatible: Should be one of:
> > + - "mediatek,mt7622-btif" : for MT7622 SoC
> > + - "mediatek,mt7623-btif" : for MT7623 SoC
> > +- reg: The base address of the BTIF register bank;
> > +- interrupts: A single interrupt specifier;
> > +- clocks: list of clock specifiers, corresponding to
> > + entries in clock-names property;
> > +- clock-names: should contain "main" entries.
> > +
> > +Optional properties:
> > +- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
> > + running on the loopback mode.
>
> I don't think this belongs in DT, but should be a module param or sysfs
> control.
>
the loopback actually is one of hardware setups so i add it as one
property in the dt or could you kindly guide me how to make judgment
accurately for listing those changes as either dt or a module param?
> > +
> > +Example:
> > +
> > + btif: btif@1100c000 {
>
> bluetooth@...
>
btif not bluetooth, which is just the interface hardware allowing the
the main processor communicating with the bluetooth hardware built in
the SoC, and is really like to the uart used by legacy bluetooth.
So i will add bluetooth as the another node.
> > + compatible = "mediatek,mt7623-btif";
> > + reg = <0 0x1100c000 0 0x1000>;
> > + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
> > + clocks = <&pericfg CLK_PERI_BTIF>;
> > + clock-names = "main";
> > + };
> > --
> > 2.7.4
> >
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
@ 2017-08-11 2:53 ` Sean Wang
0 siblings, 0 replies; 27+ messages in thread
From: Sean Wang @ 2017-08-11 2:53 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, 2017-08-10 at 11:27 -0500, Rob Herring wrote:
> On Thu, Aug 03, 2017 at 01:05:22AM +0800, sean.wang at mediatek.com wrote:
> > From: Sean Wang <sean.wang@mediatek.com>
> >
> > Document the devicetree bindings for MediaTek BTIF controller
> > which could be found on MT7622 and MT7623 SoC.
> >
> > Signed-off-by: Sean Wang <sean.wang@mediatek.com>
> > ---
> > .../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
> > 1 file changed, 26 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
> >
> > diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> > new file mode 100644
> > index 0000000..80c1f5a
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
> > @@ -0,0 +1,26 @@
> > +Device-Tree bindings for MediaTek BTIF controller found on those
> > +MediaTek SoCs with Bluetooth feature
> > +
> > +Required properties:
> > +- compatible: Should be one of:
> > + - "mediatek,mt7622-btif" : for MT7622 SoC
> > + - "mediatek,mt7623-btif" : for MT7623 SoC
> > +- reg: The base address of the BTIF register bank;
> > +- interrupts: A single interrupt specifier;
> > +- clocks: list of clock specifiers, corresponding to
> > + entries in clock-names property;
> > +- clock-names: should contain "main" entries.
> > +
> > +Optional properties:
> > +- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
> > + running on the loopback mode.
>
> I don't think this belongs in DT, but should be a module param or sysfs
> control.
>
the loopback actually is one of hardware setups so i add it as one
property in the dt or could you kindly guide me how to make judgment
accurately for listing those changes as either dt or a module param?
> > +
> > +Example:
> > +
> > + btif: btif at 1100c000 {
>
> bluetooth at ...
>
btif not bluetooth, which is just the interface hardware allowing the
the main processor communicating with the bluetooth hardware built in
the SoC, and is really like to the uart used by legacy bluetooth.
So i will add bluetooth as the another node.
> > + compatible = "mediatek,mt7623-btif";
> > + reg = <0 0x1100c000 0 0x1000>;
> > + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
> > + clocks = <&pericfg CLK_PERI_BTIF>;
> > + clock-names = "main";
> > + };
> > --
> > 2.7.4
> >
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
2017-08-11 2:53 ` Sean Wang
(?)
@ 2017-08-11 14:31 ` Rob Herring
-1 siblings, 0 replies; 27+ messages in thread
From: Rob Herring @ 2017-08-11 14:31 UTC (permalink / raw)
To: Sean Wang
Cc: Greg Kroah-Hartman, Jiri Slaby, Andy Shevchenko, Jan Kiszka,
Heikki Krogerus, Peter H, Vignesh R, Matthias Brugger,
devicetree, linux-mediatek, linux-serial, linux-arm-kernel,
linux-kernel
On Thu, Aug 10, 2017 at 9:53 PM, Sean Wang <sean.wang@mediatek.com> wrote:
> On Thu, 2017-08-10 at 11:27 -0500, Rob Herring wrote:
>> On Thu, Aug 03, 2017 at 01:05:22AM +0800, sean.wang@mediatek.com wrote:
>> > From: Sean Wang <sean.wang@mediatek.com>
>> >
>> > Document the devicetree bindings for MediaTek BTIF controller
>> > which could be found on MT7622 and MT7623 SoC.
>> >
>> > Signed-off-by: Sean Wang <sean.wang@mediatek.com>
>> > ---
>> > .../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
>> > 1 file changed, 26 insertions(+)
>> > create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
>> > new file mode 100644
>> > index 0000000..80c1f5a
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
>> > @@ -0,0 +1,26 @@
>> > +Device-Tree bindings for MediaTek BTIF controller found on those
>> > +MediaTek SoCs with Bluetooth feature
>> > +
>> > +Required properties:
>> > +- compatible: Should be one of:
>> > + - "mediatek,mt7622-btif" : for MT7622 SoC
>> > + - "mediatek,mt7623-btif" : for MT7623 SoC
>> > +- reg: The base address of the BTIF register bank;
>> > +- interrupts: A single interrupt specifier;
>> > +- clocks: list of clock specifiers, corresponding to
>> > + entries in clock-names property;
>> > +- clock-names: should contain "main" entries.
>> > +
>> > +Optional properties:
>> > +- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
>> > + running on the loopback mode.
>>
>> I don't think this belongs in DT, but should be a module param or sysfs
>> control.
>>
> the loopback actually is one of hardware setups so i add it as one
> property in the dt or could you kindly guide me how to make judgment
> accurately for listing those changes as either dt or a module param?
It's just a debug mode, right? Generally a user shouldn't have to
modify the DT to change settings. Only if you wanted a given board to
always be in loopback would this make sense in DT.
>> > +
>> > +Example:
>> > +
>> > + btif: btif@1100c000 {
>>
>> bluetooth@...
>>
> btif not bluetooth, which is just the interface hardware allowing the
> the main processor communicating with the bluetooth hardware built in
> the SoC, and is really like to the uart used by legacy bluetooth.
> So i will add bluetooth as the another node.
Right, I realized that after writing this. It should be "serial@..." instead.
>
>
>> > + compatible = "mediatek,mt7623-btif";
>> > + reg = <0 0x1100c000 0 0x1000>;
>> > + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
>> > + clocks = <&pericfg CLK_PERI_BTIF>;
>> > + clock-names = "main";
>> > + };
>> > --
>> > 2.7.4
>> >
>
>
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
@ 2017-08-11 14:31 ` Rob Herring
0 siblings, 0 replies; 27+ messages in thread
From: Rob Herring @ 2017-08-11 14:31 UTC (permalink / raw)
To: Sean Wang
Cc: Greg Kroah-Hartman, Jiri Slaby, Andy Shevchenko, Jan Kiszka,
Heikki Krogerus, Peter H, Vignesh R, Matthias Brugger,
devicetree, linux-mediatek, linux-serial, linux-arm-kernel,
linux-kernel
On Thu, Aug 10, 2017 at 9:53 PM, Sean Wang <sean.wang@mediatek.com> wrote:
> On Thu, 2017-08-10 at 11:27 -0500, Rob Herring wrote:
>> On Thu, Aug 03, 2017 at 01:05:22AM +0800, sean.wang@mediatek.com wrote:
>> > From: Sean Wang <sean.wang@mediatek.com>
>> >
>> > Document the devicetree bindings for MediaTek BTIF controller
>> > which could be found on MT7622 and MT7623 SoC.
>> >
>> > Signed-off-by: Sean Wang <sean.wang@mediatek.com>
>> > ---
>> > .../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
>> > 1 file changed, 26 insertions(+)
>> > create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
>> > new file mode 100644
>> > index 0000000..80c1f5a
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
>> > @@ -0,0 +1,26 @@
>> > +Device-Tree bindings for MediaTek BTIF controller found on those
>> > +MediaTek SoCs with Bluetooth feature
>> > +
>> > +Required properties:
>> > +- compatible: Should be one of:
>> > + - "mediatek,mt7622-btif" : for MT7622 SoC
>> > + - "mediatek,mt7623-btif" : for MT7623 SoC
>> > +- reg: The base address of the BTIF register bank;
>> > +- interrupts: A single interrupt specifier;
>> > +- clocks: list of clock specifiers, corresponding to
>> > + entries in clock-names property;
>> > +- clock-names: should contain "main" entries.
>> > +
>> > +Optional properties:
>> > +- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
>> > + running on the loopback mode.
>>
>> I don't think this belongs in DT, but should be a module param or sysfs
>> control.
>>
> the loopback actually is one of hardware setups so i add it as one
> property in the dt or could you kindly guide me how to make judgment
> accurately for listing those changes as either dt or a module param?
It's just a debug mode, right? Generally a user shouldn't have to
modify the DT to change settings. Only if you wanted a given board to
always be in loopback would this make sense in DT.
>> > +
>> > +Example:
>> > +
>> > + btif: btif@1100c000 {
>>
>> bluetooth@...
>>
> btif not bluetooth, which is just the interface hardware allowing the
> the main processor communicating with the bluetooth hardware built in
> the SoC, and is really like to the uart used by legacy bluetooth.
> So i will add bluetooth as the another node.
Right, I realized that after writing this. It should be "serial@..." instead.
>
>
>> > + compatible = "mediatek,mt7623-btif";
>> > + reg = <0 0x1100c000 0 0x1000>;
>> > + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
>> > + clocks = <&pericfg CLK_PERI_BTIF>;
>> > + clock-names = "main";
>> > + };
>> > --
>> > 2.7.4
>> >
>
>
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings
@ 2017-08-11 14:31 ` Rob Herring
0 siblings, 0 replies; 27+ messages in thread
From: Rob Herring @ 2017-08-11 14:31 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Aug 10, 2017 at 9:53 PM, Sean Wang <sean.wang@mediatek.com> wrote:
> On Thu, 2017-08-10 at 11:27 -0500, Rob Herring wrote:
>> On Thu, Aug 03, 2017 at 01:05:22AM +0800, sean.wang at mediatek.com wrote:
>> > From: Sean Wang <sean.wang@mediatek.com>
>> >
>> > Document the devicetree bindings for MediaTek BTIF controller
>> > which could be found on MT7622 and MT7623 SoC.
>> >
>> > Signed-off-by: Sean Wang <sean.wang@mediatek.com>
>> > ---
>> > .../devicetree/bindings/serial/mtk-btif.txt | 26 ++++++++++++++++++++++
>> > 1 file changed, 26 insertions(+)
>> > create mode 100644 Documentation/devicetree/bindings/serial/mtk-btif.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/serial/mtk-btif.txt b/Documentation/devicetree/bindings/serial/mtk-btif.txt
>> > new file mode 100644
>> > index 0000000..80c1f5a
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/serial/mtk-btif.txt
>> > @@ -0,0 +1,26 @@
>> > +Device-Tree bindings for MediaTek BTIF controller found on those
>> > +MediaTek SoCs with Bluetooth feature
>> > +
>> > +Required properties:
>> > +- compatible: Should be one of:
>> > + - "mediatek,mt7622-btif" : for MT7622 SoC
>> > + - "mediatek,mt7623-btif" : for MT7623 SoC
>> > +- reg: The base address of the BTIF register bank;
>> > +- interrupts: A single interrupt specifier;
>> > +- clocks: list of clock specifiers, corresponding to
>> > + entries in clock-names property;
>> > +- clock-names: should contain "main" entries.
>> > +
>> > +Optional properties:
>> > +- mediatek,loopback: Boolean; if defined, indicates that BTIF controller
>> > + running on the loopback mode.
>>
>> I don't think this belongs in DT, but should be a module param or sysfs
>> control.
>>
> the loopback actually is one of hardware setups so i add it as one
> property in the dt or could you kindly guide me how to make judgment
> accurately for listing those changes as either dt or a module param?
It's just a debug mode, right? Generally a user shouldn't have to
modify the DT to change settings. Only if you wanted a given board to
always be in loopback would this make sense in DT.
>> > +
>> > +Example:
>> > +
>> > + btif: btif at 1100c000 {
>>
>> bluetooth at ...
>>
> btif not bluetooth, which is just the interface hardware allowing the
> the main processor communicating with the bluetooth hardware built in
> the SoC, and is really like to the uart used by legacy bluetooth.
> So i will add bluetooth as the another node.
Right, I realized that after writing this. It should be "serial at ..." instead.
>
>
>> > + compatible = "mediatek,mt7623-btif";
>> > + reg = <0 0x1100c000 0 0x1000>;
>> > + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>;
>> > + clocks = <&pericfg CLK_PERI_BTIF>;
>> > + clock-names = "main";
>> > + };
>> > --
>> > 2.7.4
>> >
>
>
^ permalink raw reply [flat|nested] 27+ messages in thread
end of thread, other threads:[~2017-08-11 14:31 UTC | newest]
Thread overview: 27+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-08-02 17:05 [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller sean.wang
2017-08-02 17:05 ` sean.wang at mediatek.com
2017-08-02 17:05 ` sean.wang
2017-08-02 17:05 ` [PATCH 1/2] dt-bindings: serial: Add MediaTek BTIF controller bindings sean.wang
2017-08-02 17:05 ` sean.wang at mediatek.com
2017-08-02 17:05 ` sean.wang
2017-08-10 16:27 ` Rob Herring
2017-08-10 16:27 ` Rob Herring
2017-08-11 2:53 ` Sean Wang
2017-08-11 2:53 ` Sean Wang
2017-08-11 2:53 ` Sean Wang
2017-08-11 14:31 ` Rob Herring
2017-08-11 14:31 ` Rob Herring
2017-08-11 14:31 ` Rob Herring
2017-08-02 17:05 ` [PATCH 2/2] tty: serial: 8250: Add MediaTek BTIF controller on MT7622 and MT7623 SoC sean.wang
2017-08-02 17:05 ` sean.wang at mediatek.com
2017-08-02 17:05 ` sean.wang
2017-08-02 17:14 ` [PATCH 0/2] serial: 8250: add support for MediaTek BTIF controller Andy Shevchenko
2017-08-02 17:14 ` Andy Shevchenko
2017-08-02 17:37 ` Sean Wang
2017-08-02 17:37 ` Sean Wang
2017-08-02 17:37 ` Sean Wang
2017-08-02 18:02 ` Andy Shevchenko
2017-08-02 18:02 ` Andy Shevchenko
2017-08-02 18:02 ` Andy Shevchenko
2017-08-03 3:18 ` Sean Wang
2017-08-03 3:18 ` Sean Wang
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.