From: Cyrille Pitchen <cyrille.pitchen@atmel.com>
To: <nicolas.ferre@atmel.com>, <gregkh@linuxfoundation.org>,
<wenyou.yang@atmel.com>, <ludovic.desroches@atmel.com>,
<leilei.zhao@atmel.com>, <josh.wu@atmel.com>,
<alexandre.belloni@free-electrons.com>,
<linux-serial@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <galak@codeaurora.org>,
<ijc+devicetree@hellion.org.uk>, <mark.rutland@arm.com>,
<pawel.moll@arm.com>, <robh+dt@kernel.org>,
Cyrille Pitchen <cyrille.pitchen@atmel.com>
Subject: [PATCH linux-next v2 2/4] tty/serial: at91: fix some macro definitions to fit coding style
Date: Thu, 11 Jun 2015 18:20:15 +0200 [thread overview]
Message-ID: <f22220ee42ecf9301def7e90154b74937ca9ffab.1434038494.git.cyrille.pitchen@atmel.com> (raw)
In-Reply-To: <cover.1434038494.git.cyrille.pitchen@atmel.com>
This patch updates macro definitions in atmel_serial.h to fit the
80 column rule.
Please note that some deprecated comments such as "[AT91SAM9261 only]"
are removed as the corresponding bits also exist in some later chips.
The patch also fix macro definitions in atmel_serial.c to replace
(port,v) by (port, v).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
drivers/tty/serial/atmel_serial.c | 52 +++++-----
include/linux/atmel_serial.h | 204 +++++++++++++++++++-------------------
2 files changed, 128 insertions(+), 128 deletions(-)
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 2a8f528..112e74b 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -89,35 +89,35 @@ static void atmel_stop_rx(struct uart_port *port);
#define ATMEL_ISR_PASS_LIMIT 256
/* UART registers. CR is write-only, hence no GET macro */
-#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
-#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
-#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
-#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
-#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
-#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
-#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
-#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
-#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
-#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
-#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
-#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
-#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
-#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
-#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
+#define UART_PUT_CR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
+#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
+#define UART_PUT_MR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
+#define UART_PUT_IER(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
+#define UART_PUT_IDR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
+#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
+#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
+#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
+#define UART_PUT_CHAR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
+#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
+#define UART_PUT_BRGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
+#define UART_PUT_RTOR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
+#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
+#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
+#define UART_GET_IP_VERS(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
/* PDC registers */
-#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
-#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
+#define UART_PUT_PTCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
+#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
-#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
-#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
-#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
-#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
-#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
+#define UART_PUT_RPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
+#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
+#define UART_PUT_RCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
+#define UART_PUT_RNPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
+#define UART_PUT_RNCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
-#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
-#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
-#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
+#define UART_PUT_TPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
+#define UART_PUT_TCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
+#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
struct atmel_dma_buffer {
unsigned char *buf;
@@ -1684,7 +1684,7 @@ static void atmel_get_ip_name(struct uart_port *port)
atmel_port->is_usart = false;
} else {
/* fallback for older SoCs: use version field */
- version = UART_GET_IP_VERSION(port);
+ version = UART_GET_IP_VERS(port);
switch (version) {
case 0x302:
case 0x10213:
diff --git a/include/linux/atmel_serial.h b/include/linux/atmel_serial.h
index 00beddf..c384c21 100644
--- a/include/linux/atmel_serial.h
+++ b/include/linux/atmel_serial.h
@@ -16,115 +16,115 @@
#ifndef ATMEL_SERIAL_H
#define ATMEL_SERIAL_H
-#define ATMEL_US_CR 0x00 /* Control Register */
-#define ATMEL_US_RSTRX (1 << 2) /* Reset Receiver */
-#define ATMEL_US_RSTTX (1 << 3) /* Reset Transmitter */
-#define ATMEL_US_RXEN (1 << 4) /* Receiver Enable */
-#define ATMEL_US_RXDIS (1 << 5) /* Receiver Disable */
-#define ATMEL_US_TXEN (1 << 6) /* Transmitter Enable */
-#define ATMEL_US_TXDIS (1 << 7) /* Transmitter Disable */
-#define ATMEL_US_RSTSTA (1 << 8) /* Reset Status Bits */
-#define ATMEL_US_STTBRK (1 << 9) /* Start Break */
-#define ATMEL_US_STPBRK (1 << 10) /* Stop Break */
-#define ATMEL_US_STTTO (1 << 11) /* Start Time-out */
-#define ATMEL_US_SENDA (1 << 12) /* Send Address */
-#define ATMEL_US_RSTIT (1 << 13) /* Reset Iterations */
-#define ATMEL_US_RSTNACK (1 << 14) /* Reset Non Acknowledge */
-#define ATMEL_US_RETTO (1 << 15) /* Rearm Time-out */
-#define ATMEL_US_DTREN (1 << 16) /* Data Terminal Ready Enable [AT91RM9200 only] */
-#define ATMEL_US_DTRDIS (1 << 17) /* Data Terminal Ready Disable [AT91RM9200 only] */
-#define ATMEL_US_RTSEN (1 << 18) /* Request To Send Enable */
-#define ATMEL_US_RTSDIS (1 << 19) /* Request To Send Disable */
+#define ATMEL_US_CR 0x00 /* Control Register */
+#define ATMEL_US_RSTRX BIT(2) /* Reset Receiver */
+#define ATMEL_US_RSTTX BIT(3) /* Reset Transmitter */
+#define ATMEL_US_RXEN BIT(4) /* Receiver Enable */
+#define ATMEL_US_RXDIS BIT(5) /* Receiver Disable */
+#define ATMEL_US_TXEN BIT(6) /* Transmitter Enable */
+#define ATMEL_US_TXDIS BIT(7) /* Transmitter Disable */
+#define ATMEL_US_RSTSTA BIT(8) /* Reset Status Bits */
+#define ATMEL_US_STTBRK BIT(9) /* Start Break */
+#define ATMEL_US_STPBRK BIT(10) /* Stop Break */
+#define ATMEL_US_STTTO BIT(11) /* Start Time-out */
+#define ATMEL_US_SENDA BIT(12) /* Send Address */
+#define ATMEL_US_RSTIT BIT(13) /* Reset Iterations */
+#define ATMEL_US_RSTNACK BIT(14) /* Reset Non Acknowledge */
+#define ATMEL_US_RETTO BIT(15) /* Rearm Time-out */
+#define ATMEL_US_DTREN BIT(16) /* Data Terminal Ready Enable */
+#define ATMEL_US_DTRDIS BIT(17) /* Data Terminal Ready Disable */
+#define ATMEL_US_RTSEN BIT(18) /* Request To Send Enable */
+#define ATMEL_US_RTSDIS BIT(19) /* Request To Send Disable */
-#define ATMEL_US_MR 0x04 /* Mode Register */
-#define ATMEL_US_USMODE (0xf << 0) /* Mode of the USART */
-#define ATMEL_US_USMODE_NORMAL 0
-#define ATMEL_US_USMODE_RS485 1
-#define ATMEL_US_USMODE_HWHS 2
-#define ATMEL_US_USMODE_MODEM 3
-#define ATMEL_US_USMODE_ISO7816_T0 4
-#define ATMEL_US_USMODE_ISO7816_T1 6
-#define ATMEL_US_USMODE_IRDA 8
-#define ATMEL_US_USCLKS (3 << 4) /* Clock Selection */
-#define ATMEL_US_USCLKS_MCK (0 << 4)
-#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
-#define ATMEL_US_USCLKS_SCK (3 << 4)
-#define ATMEL_US_CHRL (3 << 6) /* Character Length */
-#define ATMEL_US_CHRL_5 (0 << 6)
-#define ATMEL_US_CHRL_6 (1 << 6)
-#define ATMEL_US_CHRL_7 (2 << 6)
-#define ATMEL_US_CHRL_8 (3 << 6)
-#define ATMEL_US_SYNC (1 << 8) /* Synchronous Mode Select */
-#define ATMEL_US_PAR (7 << 9) /* Parity Type */
-#define ATMEL_US_PAR_EVEN (0 << 9)
-#define ATMEL_US_PAR_ODD (1 << 9)
-#define ATMEL_US_PAR_SPACE (2 << 9)
-#define ATMEL_US_PAR_MARK (3 << 9)
-#define ATMEL_US_PAR_NONE (4 << 9)
-#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
-#define ATMEL_US_NBSTOP (3 << 12) /* Number of Stop Bits */
-#define ATMEL_US_NBSTOP_1 (0 << 12)
-#define ATMEL_US_NBSTOP_1_5 (1 << 12)
-#define ATMEL_US_NBSTOP_2 (2 << 12)
-#define ATMEL_US_CHMODE (3 << 14) /* Channel Mode */
-#define ATMEL_US_CHMODE_NORMAL (0 << 14)
-#define ATMEL_US_CHMODE_ECHO (1 << 14)
-#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
-#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
-#define ATMEL_US_MSBF (1 << 16) /* Bit Order */
-#define ATMEL_US_MODE9 (1 << 17) /* 9-bit Character Length */
-#define ATMEL_US_CLKO (1 << 18) /* Clock Output Select */
-#define ATMEL_US_OVER (1 << 19) /* Oversampling Mode */
-#define ATMEL_US_INACK (1 << 20) /* Inhibit Non Acknowledge */
-#define ATMEL_US_DSNACK (1 << 21) /* Disable Successive NACK */
-#define ATMEL_US_MAX_ITER (7 << 24) /* Max Iterations */
-#define ATMEL_US_FILTER (1 << 28) /* Infrared Receive Line Filter */
+#define ATMEL_US_MR 0x04 /* Mode Register */
+#define ATMEL_US_USMODE GENMASK(3, 0) /* Mode of the USART */
+#define ATMEL_US_USMODE_NORMAL 0
+#define ATMEL_US_USMODE_RS485 1
+#define ATMEL_US_USMODE_HWHS 2
+#define ATMEL_US_USMODE_MODEM 3
+#define ATMEL_US_USMODE_ISO7816_T0 4
+#define ATMEL_US_USMODE_ISO7816_T1 6
+#define ATMEL_US_USMODE_IRDA 8
+#define ATMEL_US_USCLKS GENMASK(5, 4) /* Clock Selection */
+#define ATMEL_US_USCLKS_MCK (0 << 4)
+#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
+#define ATMEL_US_USCLKS_SCK (3 << 4)
+#define ATMEL_US_CHRL GENMASK(7, 6) /* Character Length */
+#define ATMEL_US_CHRL_5 (0 << 6)
+#define ATMEL_US_CHRL_6 (1 << 6)
+#define ATMEL_US_CHRL_7 (2 << 6)
+#define ATMEL_US_CHRL_8 (3 << 6)
+#define ATMEL_US_SYNC BIT(8) /* Synchronous Mode Select */
+#define ATMEL_US_PAR GENMASK(11, 9) /* Parity Type */
+#define ATMEL_US_PAR_EVEN (0 << 9)
+#define ATMEL_US_PAR_ODD (1 << 9)
+#define ATMEL_US_PAR_SPACE (2 << 9)
+#define ATMEL_US_PAR_MARK (3 << 9)
+#define ATMEL_US_PAR_NONE (4 << 9)
+#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
+#define ATMEL_US_NBSTOP GENMASK(13, 12) /* Number of Stop Bits */
+#define ATMEL_US_NBSTOP_1 (0 << 12)
+#define ATMEL_US_NBSTOP_1_5 (1 << 12)
+#define ATMEL_US_NBSTOP_2 (2 << 12)
+#define ATMEL_US_CHMODE GENMASK(15, 14) /* Channel Mode */
+#define ATMEL_US_CHMODE_NORMAL (0 << 14)
+#define ATMEL_US_CHMODE_ECHO (1 << 14)
+#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
+#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
+#define ATMEL_US_MSBF BIT(16) /* Bit Order */
+#define ATMEL_US_MODE9 BIT(17) /* 9-bit Character Length */
+#define ATMEL_US_CLKO BIT(18) /* Clock Output Select */
+#define ATMEL_US_OVER BIT(19) /* Oversampling Mode */
+#define ATMEL_US_INACK BIT(20) /* Inhibit Non Acknowledge */
+#define ATMEL_US_DSNACK BIT(21) /* Disable Successive NACK */
+#define ATMEL_US_MAX_ITER GENMASK(26, 24) /* Max Iterations */
+#define ATMEL_US_FILTER BIT(28) /* Infrared Receive Line Filter */
-#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
-#define ATMEL_US_RXRDY (1 << 0) /* Receiver Ready */
-#define ATMEL_US_TXRDY (1 << 1) /* Transmitter Ready */
-#define ATMEL_US_RXBRK (1 << 2) /* Break Received / End of Break */
-#define ATMEL_US_ENDRX (1 << 3) /* End of Receiver Transfer */
-#define ATMEL_US_ENDTX (1 << 4) /* End of Transmitter Transfer */
-#define ATMEL_US_OVRE (1 << 5) /* Overrun Error */
-#define ATMEL_US_FRAME (1 << 6) /* Framing Error */
-#define ATMEL_US_PARE (1 << 7) /* Parity Error */
-#define ATMEL_US_TIMEOUT (1 << 8) /* Receiver Time-out */
-#define ATMEL_US_TXEMPTY (1 << 9) /* Transmitter Empty */
-#define ATMEL_US_ITERATION (1 << 10) /* Max number of Repetitions Reached */
-#define ATMEL_US_TXBUFE (1 << 11) /* Transmission Buffer Empty */
-#define ATMEL_US_RXBUFF (1 << 12) /* Reception Buffer Full */
-#define ATMEL_US_NACK (1 << 13) /* Non Acknowledge */
-#define ATMEL_US_RIIC (1 << 16) /* Ring Indicator Input Change [AT91RM9200 only] */
-#define ATMEL_US_DSRIC (1 << 17) /* Data Set Ready Input Change [AT91RM9200 only] */
-#define ATMEL_US_DCDIC (1 << 18) /* Data Carrier Detect Input Change [AT91RM9200 only] */
-#define ATMEL_US_CTSIC (1 << 19) /* Clear to Send Input Change */
-#define ATMEL_US_RI (1 << 20) /* RI */
-#define ATMEL_US_DSR (1 << 21) /* DSR */
-#define ATMEL_US_DCD (1 << 22) /* DCD */
-#define ATMEL_US_CTS (1 << 23) /* CTS */
+#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
+#define ATMEL_US_RXRDY BIT(0) /* Receiver Ready */
+#define ATMEL_US_TXRDY BIT(1) /* Transmitter Ready */
+#define ATMEL_US_RXBRK BIT(2) /* Break Received / End of Break */
+#define ATMEL_US_ENDRX BIT(3) /* End of Receiver Transfer */
+#define ATMEL_US_ENDTX BIT(4) /* End of Transmitter Transfer */
+#define ATMEL_US_OVRE BIT(5) /* Overrun Error */
+#define ATMEL_US_FRAME BIT(6) /* Framing Error */
+#define ATMEL_US_PARE BIT(7) /* Parity Error */
+#define ATMEL_US_TIMEOUT BIT(8) /* Receiver Time-out */
+#define ATMEL_US_TXEMPTY BIT(9) /* Transmitter Empty */
+#define ATMEL_US_ITERATION BIT(10) /* Max number of Repetitions Reached */
+#define ATMEL_US_TXBUFE BIT(11) /* Transmission Buffer Empty */
+#define ATMEL_US_RXBUFF BIT(12) /* Reception Buffer Full */
+#define ATMEL_US_NACK BIT(13) /* Non Acknowledge */
+#define ATMEL_US_RIIC BIT(16) /* Ring Indicator Input Change */
+#define ATMEL_US_DSRIC BIT(17) /* Data Set Ready Input Change */
+#define ATMEL_US_DCDIC BIT(18) /* Data Carrier Detect Input Change */
+#define ATMEL_US_CTSIC BIT(19) /* Clear to Send Input Change */
+#define ATMEL_US_RI BIT(20) /* RI */
+#define ATMEL_US_DSR BIT(21) /* DSR */
+#define ATMEL_US_DCD BIT(22) /* DCD */
+#define ATMEL_US_CTS BIT(23) /* CTS */
-#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
-#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
-#define ATMEL_US_CSR 0x14 /* Channel Status Register */
-#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
-#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
-#define ATMEL_US_SYNH (1 << 15) /* Transmit/Receive Sync [AT91SAM9261 only] */
+#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
+#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
+#define ATMEL_US_CSR 0x14 /* Channel Status Register */
+#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
+#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
+#define ATMEL_US_SYNH BIT(15) /* Transmit/Receive Sync */
-#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
-#define ATMEL_US_CD (0xffff << 0) /* Clock Divider */
+#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
+#define ATMEL_US_CD GENMASK(15, 0) /* Clock Divider */
-#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
-#define ATMEL_US_TO (0xffff << 0) /* Time-out Value */
+#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
+#define ATMEL_US_TO GENMASK(15, 0) /* Time-out Value */
-#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
-#define ATMEL_US_TG (0xff << 0) /* Timeguard Value */
+#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
+#define ATMEL_US_TG GENMASK(7, 0) /* Timeguard Value */
-#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
-#define ATMEL_US_NER 0x44 /* Number of Errors Register */
-#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
+#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
+#define ATMEL_US_NER 0x44 /* Number of Errors Register */
+#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
-#define ATMEL_US_NAME 0xf0 /* Ip Name */
-#define ATMEL_US_VERSION 0xfc /* Ip Version */
+#define ATMEL_US_NAME 0xf0 /* Ip Name */
+#define ATMEL_US_VERSION 0xfc /* Ip Version */
#endif
--
1.8.2.2
WARNING: multiple messages have this Message-ID (diff)
From: Cyrille Pitchen <cyrille.pitchen@atmel.com>
To: nicolas.ferre@atmel.com, gregkh@linuxfoundation.org,
wenyou.yang@atmel.com, ludovic.desroches@atmel.com,
leilei.zhao@atmel.com, josh.wu@atmel.com,
alexandre.belloni@free-electrons.com,
linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
galak@codeaurora.org, ijc+devicetree@hellion.org.uk,
mark.rutland@arm.com, pawel.moll@arm.com, robh+dt@kernel.org,
Cyrille Pitchen <cyrille.pitchen@atmel.com>
Subject: [PATCH linux-next v2 2/4] tty/serial: at91: fix some macro definitions to fit coding style
Date: Thu, 11 Jun 2015 18:20:15 +0200 [thread overview]
Message-ID: <f22220ee42ecf9301def7e90154b74937ca9ffab.1434038494.git.cyrille.pitchen@atmel.com> (raw)
In-Reply-To: <cover.1434038494.git.cyrille.pitchen@atmel.com>
This patch updates macro definitions in atmel_serial.h to fit the
80 column rule.
Please note that some deprecated comments such as "[AT91SAM9261 only]"
are removed as the corresponding bits also exist in some later chips.
The patch also fix macro definitions in atmel_serial.c to replace
(port,v) by (port, v).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
drivers/tty/serial/atmel_serial.c | 52 +++++-----
include/linux/atmel_serial.h | 204 +++++++++++++++++++-------------------
2 files changed, 128 insertions(+), 128 deletions(-)
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 2a8f528..112e74b 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -89,35 +89,35 @@ static void atmel_stop_rx(struct uart_port *port);
#define ATMEL_ISR_PASS_LIMIT 256
/* UART registers. CR is write-only, hence no GET macro */
-#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
-#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
-#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
-#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
-#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
-#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
-#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
-#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
-#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
-#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
-#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
-#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
-#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
-#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
-#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
+#define UART_PUT_CR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
+#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
+#define UART_PUT_MR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
+#define UART_PUT_IER(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
+#define UART_PUT_IDR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
+#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
+#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
+#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
+#define UART_PUT_CHAR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
+#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
+#define UART_PUT_BRGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
+#define UART_PUT_RTOR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
+#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
+#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
+#define UART_GET_IP_VERS(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
/* PDC registers */
-#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
-#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
+#define UART_PUT_PTCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
+#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
-#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
-#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
-#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
-#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
-#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
+#define UART_PUT_RPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
+#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
+#define UART_PUT_RCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
+#define UART_PUT_RNPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
+#define UART_PUT_RNCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
-#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
-#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
-#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
+#define UART_PUT_TPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
+#define UART_PUT_TCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
+#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
struct atmel_dma_buffer {
unsigned char *buf;
@@ -1684,7 +1684,7 @@ static void atmel_get_ip_name(struct uart_port *port)
atmel_port->is_usart = false;
} else {
/* fallback for older SoCs: use version field */
- version = UART_GET_IP_VERSION(port);
+ version = UART_GET_IP_VERS(port);
switch (version) {
case 0x302:
case 0x10213:
diff --git a/include/linux/atmel_serial.h b/include/linux/atmel_serial.h
index 00beddf..c384c21 100644
--- a/include/linux/atmel_serial.h
+++ b/include/linux/atmel_serial.h
@@ -16,115 +16,115 @@
#ifndef ATMEL_SERIAL_H
#define ATMEL_SERIAL_H
-#define ATMEL_US_CR 0x00 /* Control Register */
-#define ATMEL_US_RSTRX (1 << 2) /* Reset Receiver */
-#define ATMEL_US_RSTTX (1 << 3) /* Reset Transmitter */
-#define ATMEL_US_RXEN (1 << 4) /* Receiver Enable */
-#define ATMEL_US_RXDIS (1 << 5) /* Receiver Disable */
-#define ATMEL_US_TXEN (1 << 6) /* Transmitter Enable */
-#define ATMEL_US_TXDIS (1 << 7) /* Transmitter Disable */
-#define ATMEL_US_RSTSTA (1 << 8) /* Reset Status Bits */
-#define ATMEL_US_STTBRK (1 << 9) /* Start Break */
-#define ATMEL_US_STPBRK (1 << 10) /* Stop Break */
-#define ATMEL_US_STTTO (1 << 11) /* Start Time-out */
-#define ATMEL_US_SENDA (1 << 12) /* Send Address */
-#define ATMEL_US_RSTIT (1 << 13) /* Reset Iterations */
-#define ATMEL_US_RSTNACK (1 << 14) /* Reset Non Acknowledge */
-#define ATMEL_US_RETTO (1 << 15) /* Rearm Time-out */
-#define ATMEL_US_DTREN (1 << 16) /* Data Terminal Ready Enable [AT91RM9200 only] */
-#define ATMEL_US_DTRDIS (1 << 17) /* Data Terminal Ready Disable [AT91RM9200 only] */
-#define ATMEL_US_RTSEN (1 << 18) /* Request To Send Enable */
-#define ATMEL_US_RTSDIS (1 << 19) /* Request To Send Disable */
+#define ATMEL_US_CR 0x00 /* Control Register */
+#define ATMEL_US_RSTRX BIT(2) /* Reset Receiver */
+#define ATMEL_US_RSTTX BIT(3) /* Reset Transmitter */
+#define ATMEL_US_RXEN BIT(4) /* Receiver Enable */
+#define ATMEL_US_RXDIS BIT(5) /* Receiver Disable */
+#define ATMEL_US_TXEN BIT(6) /* Transmitter Enable */
+#define ATMEL_US_TXDIS BIT(7) /* Transmitter Disable */
+#define ATMEL_US_RSTSTA BIT(8) /* Reset Status Bits */
+#define ATMEL_US_STTBRK BIT(9) /* Start Break */
+#define ATMEL_US_STPBRK BIT(10) /* Stop Break */
+#define ATMEL_US_STTTO BIT(11) /* Start Time-out */
+#define ATMEL_US_SENDA BIT(12) /* Send Address */
+#define ATMEL_US_RSTIT BIT(13) /* Reset Iterations */
+#define ATMEL_US_RSTNACK BIT(14) /* Reset Non Acknowledge */
+#define ATMEL_US_RETTO BIT(15) /* Rearm Time-out */
+#define ATMEL_US_DTREN BIT(16) /* Data Terminal Ready Enable */
+#define ATMEL_US_DTRDIS BIT(17) /* Data Terminal Ready Disable */
+#define ATMEL_US_RTSEN BIT(18) /* Request To Send Enable */
+#define ATMEL_US_RTSDIS BIT(19) /* Request To Send Disable */
-#define ATMEL_US_MR 0x04 /* Mode Register */
-#define ATMEL_US_USMODE (0xf << 0) /* Mode of the USART */
-#define ATMEL_US_USMODE_NORMAL 0
-#define ATMEL_US_USMODE_RS485 1
-#define ATMEL_US_USMODE_HWHS 2
-#define ATMEL_US_USMODE_MODEM 3
-#define ATMEL_US_USMODE_ISO7816_T0 4
-#define ATMEL_US_USMODE_ISO7816_T1 6
-#define ATMEL_US_USMODE_IRDA 8
-#define ATMEL_US_USCLKS (3 << 4) /* Clock Selection */
-#define ATMEL_US_USCLKS_MCK (0 << 4)
-#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
-#define ATMEL_US_USCLKS_SCK (3 << 4)
-#define ATMEL_US_CHRL (3 << 6) /* Character Length */
-#define ATMEL_US_CHRL_5 (0 << 6)
-#define ATMEL_US_CHRL_6 (1 << 6)
-#define ATMEL_US_CHRL_7 (2 << 6)
-#define ATMEL_US_CHRL_8 (3 << 6)
-#define ATMEL_US_SYNC (1 << 8) /* Synchronous Mode Select */
-#define ATMEL_US_PAR (7 << 9) /* Parity Type */
-#define ATMEL_US_PAR_EVEN (0 << 9)
-#define ATMEL_US_PAR_ODD (1 << 9)
-#define ATMEL_US_PAR_SPACE (2 << 9)
-#define ATMEL_US_PAR_MARK (3 << 9)
-#define ATMEL_US_PAR_NONE (4 << 9)
-#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
-#define ATMEL_US_NBSTOP (3 << 12) /* Number of Stop Bits */
-#define ATMEL_US_NBSTOP_1 (0 << 12)
-#define ATMEL_US_NBSTOP_1_5 (1 << 12)
-#define ATMEL_US_NBSTOP_2 (2 << 12)
-#define ATMEL_US_CHMODE (3 << 14) /* Channel Mode */
-#define ATMEL_US_CHMODE_NORMAL (0 << 14)
-#define ATMEL_US_CHMODE_ECHO (1 << 14)
-#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
-#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
-#define ATMEL_US_MSBF (1 << 16) /* Bit Order */
-#define ATMEL_US_MODE9 (1 << 17) /* 9-bit Character Length */
-#define ATMEL_US_CLKO (1 << 18) /* Clock Output Select */
-#define ATMEL_US_OVER (1 << 19) /* Oversampling Mode */
-#define ATMEL_US_INACK (1 << 20) /* Inhibit Non Acknowledge */
-#define ATMEL_US_DSNACK (1 << 21) /* Disable Successive NACK */
-#define ATMEL_US_MAX_ITER (7 << 24) /* Max Iterations */
-#define ATMEL_US_FILTER (1 << 28) /* Infrared Receive Line Filter */
+#define ATMEL_US_MR 0x04 /* Mode Register */
+#define ATMEL_US_USMODE GENMASK(3, 0) /* Mode of the USART */
+#define ATMEL_US_USMODE_NORMAL 0
+#define ATMEL_US_USMODE_RS485 1
+#define ATMEL_US_USMODE_HWHS 2
+#define ATMEL_US_USMODE_MODEM 3
+#define ATMEL_US_USMODE_ISO7816_T0 4
+#define ATMEL_US_USMODE_ISO7816_T1 6
+#define ATMEL_US_USMODE_IRDA 8
+#define ATMEL_US_USCLKS GENMASK(5, 4) /* Clock Selection */
+#define ATMEL_US_USCLKS_MCK (0 << 4)
+#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
+#define ATMEL_US_USCLKS_SCK (3 << 4)
+#define ATMEL_US_CHRL GENMASK(7, 6) /* Character Length */
+#define ATMEL_US_CHRL_5 (0 << 6)
+#define ATMEL_US_CHRL_6 (1 << 6)
+#define ATMEL_US_CHRL_7 (2 << 6)
+#define ATMEL_US_CHRL_8 (3 << 6)
+#define ATMEL_US_SYNC BIT(8) /* Synchronous Mode Select */
+#define ATMEL_US_PAR GENMASK(11, 9) /* Parity Type */
+#define ATMEL_US_PAR_EVEN (0 << 9)
+#define ATMEL_US_PAR_ODD (1 << 9)
+#define ATMEL_US_PAR_SPACE (2 << 9)
+#define ATMEL_US_PAR_MARK (3 << 9)
+#define ATMEL_US_PAR_NONE (4 << 9)
+#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
+#define ATMEL_US_NBSTOP GENMASK(13, 12) /* Number of Stop Bits */
+#define ATMEL_US_NBSTOP_1 (0 << 12)
+#define ATMEL_US_NBSTOP_1_5 (1 << 12)
+#define ATMEL_US_NBSTOP_2 (2 << 12)
+#define ATMEL_US_CHMODE GENMASK(15, 14) /* Channel Mode */
+#define ATMEL_US_CHMODE_NORMAL (0 << 14)
+#define ATMEL_US_CHMODE_ECHO (1 << 14)
+#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
+#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
+#define ATMEL_US_MSBF BIT(16) /* Bit Order */
+#define ATMEL_US_MODE9 BIT(17) /* 9-bit Character Length */
+#define ATMEL_US_CLKO BIT(18) /* Clock Output Select */
+#define ATMEL_US_OVER BIT(19) /* Oversampling Mode */
+#define ATMEL_US_INACK BIT(20) /* Inhibit Non Acknowledge */
+#define ATMEL_US_DSNACK BIT(21) /* Disable Successive NACK */
+#define ATMEL_US_MAX_ITER GENMASK(26, 24) /* Max Iterations */
+#define ATMEL_US_FILTER BIT(28) /* Infrared Receive Line Filter */
-#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
-#define ATMEL_US_RXRDY (1 << 0) /* Receiver Ready */
-#define ATMEL_US_TXRDY (1 << 1) /* Transmitter Ready */
-#define ATMEL_US_RXBRK (1 << 2) /* Break Received / End of Break */
-#define ATMEL_US_ENDRX (1 << 3) /* End of Receiver Transfer */
-#define ATMEL_US_ENDTX (1 << 4) /* End of Transmitter Transfer */
-#define ATMEL_US_OVRE (1 << 5) /* Overrun Error */
-#define ATMEL_US_FRAME (1 << 6) /* Framing Error */
-#define ATMEL_US_PARE (1 << 7) /* Parity Error */
-#define ATMEL_US_TIMEOUT (1 << 8) /* Receiver Time-out */
-#define ATMEL_US_TXEMPTY (1 << 9) /* Transmitter Empty */
-#define ATMEL_US_ITERATION (1 << 10) /* Max number of Repetitions Reached */
-#define ATMEL_US_TXBUFE (1 << 11) /* Transmission Buffer Empty */
-#define ATMEL_US_RXBUFF (1 << 12) /* Reception Buffer Full */
-#define ATMEL_US_NACK (1 << 13) /* Non Acknowledge */
-#define ATMEL_US_RIIC (1 << 16) /* Ring Indicator Input Change [AT91RM9200 only] */
-#define ATMEL_US_DSRIC (1 << 17) /* Data Set Ready Input Change [AT91RM9200 only] */
-#define ATMEL_US_DCDIC (1 << 18) /* Data Carrier Detect Input Change [AT91RM9200 only] */
-#define ATMEL_US_CTSIC (1 << 19) /* Clear to Send Input Change */
-#define ATMEL_US_RI (1 << 20) /* RI */
-#define ATMEL_US_DSR (1 << 21) /* DSR */
-#define ATMEL_US_DCD (1 << 22) /* DCD */
-#define ATMEL_US_CTS (1 << 23) /* CTS */
+#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
+#define ATMEL_US_RXRDY BIT(0) /* Receiver Ready */
+#define ATMEL_US_TXRDY BIT(1) /* Transmitter Ready */
+#define ATMEL_US_RXBRK BIT(2) /* Break Received / End of Break */
+#define ATMEL_US_ENDRX BIT(3) /* End of Receiver Transfer */
+#define ATMEL_US_ENDTX BIT(4) /* End of Transmitter Transfer */
+#define ATMEL_US_OVRE BIT(5) /* Overrun Error */
+#define ATMEL_US_FRAME BIT(6) /* Framing Error */
+#define ATMEL_US_PARE BIT(7) /* Parity Error */
+#define ATMEL_US_TIMEOUT BIT(8) /* Receiver Time-out */
+#define ATMEL_US_TXEMPTY BIT(9) /* Transmitter Empty */
+#define ATMEL_US_ITERATION BIT(10) /* Max number of Repetitions Reached */
+#define ATMEL_US_TXBUFE BIT(11) /* Transmission Buffer Empty */
+#define ATMEL_US_RXBUFF BIT(12) /* Reception Buffer Full */
+#define ATMEL_US_NACK BIT(13) /* Non Acknowledge */
+#define ATMEL_US_RIIC BIT(16) /* Ring Indicator Input Change */
+#define ATMEL_US_DSRIC BIT(17) /* Data Set Ready Input Change */
+#define ATMEL_US_DCDIC BIT(18) /* Data Carrier Detect Input Change */
+#define ATMEL_US_CTSIC BIT(19) /* Clear to Send Input Change */
+#define ATMEL_US_RI BIT(20) /* RI */
+#define ATMEL_US_DSR BIT(21) /* DSR */
+#define ATMEL_US_DCD BIT(22) /* DCD */
+#define ATMEL_US_CTS BIT(23) /* CTS */
-#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
-#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
-#define ATMEL_US_CSR 0x14 /* Channel Status Register */
-#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
-#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
-#define ATMEL_US_SYNH (1 << 15) /* Transmit/Receive Sync [AT91SAM9261 only] */
+#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
+#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
+#define ATMEL_US_CSR 0x14 /* Channel Status Register */
+#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
+#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
+#define ATMEL_US_SYNH BIT(15) /* Transmit/Receive Sync */
-#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
-#define ATMEL_US_CD (0xffff << 0) /* Clock Divider */
+#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
+#define ATMEL_US_CD GENMASK(15, 0) /* Clock Divider */
-#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
-#define ATMEL_US_TO (0xffff << 0) /* Time-out Value */
+#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
+#define ATMEL_US_TO GENMASK(15, 0) /* Time-out Value */
-#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
-#define ATMEL_US_TG (0xff << 0) /* Timeguard Value */
+#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
+#define ATMEL_US_TG GENMASK(7, 0) /* Timeguard Value */
-#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
-#define ATMEL_US_NER 0x44 /* Number of Errors Register */
-#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
+#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
+#define ATMEL_US_NER 0x44 /* Number of Errors Register */
+#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
-#define ATMEL_US_NAME 0xf0 /* Ip Name */
-#define ATMEL_US_VERSION 0xfc /* Ip Version */
+#define ATMEL_US_NAME 0xf0 /* Ip Name */
+#define ATMEL_US_VERSION 0xfc /* Ip Version */
#endif
--
1.8.2.2
WARNING: multiple messages have this Message-ID (diff)
From: cyrille.pitchen@atmel.com (Cyrille Pitchen)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH linux-next v2 2/4] tty/serial: at91: fix some macro definitions to fit coding style
Date: Thu, 11 Jun 2015 18:20:15 +0200 [thread overview]
Message-ID: <f22220ee42ecf9301def7e90154b74937ca9ffab.1434038494.git.cyrille.pitchen@atmel.com> (raw)
In-Reply-To: <cover.1434038494.git.cyrille.pitchen@atmel.com>
This patch updates macro definitions in atmel_serial.h to fit the
80 column rule.
Please note that some deprecated comments such as "[AT91SAM9261 only]"
are removed as the corresponding bits also exist in some later chips.
The patch also fix macro definitions in atmel_serial.c to replace
(port,v) by (port, v).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
drivers/tty/serial/atmel_serial.c | 52 +++++-----
include/linux/atmel_serial.h | 204 +++++++++++++++++++-------------------
2 files changed, 128 insertions(+), 128 deletions(-)
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 2a8f528..112e74b 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -89,35 +89,35 @@ static void atmel_stop_rx(struct uart_port *port);
#define ATMEL_ISR_PASS_LIMIT 256
/* UART registers. CR is write-only, hence no GET macro */
-#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
-#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
-#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
-#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
-#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
-#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
-#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
-#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
-#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
-#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
-#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
-#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
-#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
-#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
-#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
+#define UART_PUT_CR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
+#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
+#define UART_PUT_MR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
+#define UART_PUT_IER(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
+#define UART_PUT_IDR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
+#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
+#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
+#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
+#define UART_PUT_CHAR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
+#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
+#define UART_PUT_BRGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
+#define UART_PUT_RTOR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
+#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
+#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
+#define UART_GET_IP_VERS(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
/* PDC registers */
-#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
-#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
+#define UART_PUT_PTCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
+#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
-#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
-#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
-#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
-#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
-#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
+#define UART_PUT_RPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
+#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
+#define UART_PUT_RCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
+#define UART_PUT_RNPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
+#define UART_PUT_RNCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
-#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
-#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
-#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
+#define UART_PUT_TPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
+#define UART_PUT_TCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
+#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
struct atmel_dma_buffer {
unsigned char *buf;
@@ -1684,7 +1684,7 @@ static void atmel_get_ip_name(struct uart_port *port)
atmel_port->is_usart = false;
} else {
/* fallback for older SoCs: use version field */
- version = UART_GET_IP_VERSION(port);
+ version = UART_GET_IP_VERS(port);
switch (version) {
case 0x302:
case 0x10213:
diff --git a/include/linux/atmel_serial.h b/include/linux/atmel_serial.h
index 00beddf..c384c21 100644
--- a/include/linux/atmel_serial.h
+++ b/include/linux/atmel_serial.h
@@ -16,115 +16,115 @@
#ifndef ATMEL_SERIAL_H
#define ATMEL_SERIAL_H
-#define ATMEL_US_CR 0x00 /* Control Register */
-#define ATMEL_US_RSTRX (1 << 2) /* Reset Receiver */
-#define ATMEL_US_RSTTX (1 << 3) /* Reset Transmitter */
-#define ATMEL_US_RXEN (1 << 4) /* Receiver Enable */
-#define ATMEL_US_RXDIS (1 << 5) /* Receiver Disable */
-#define ATMEL_US_TXEN (1 << 6) /* Transmitter Enable */
-#define ATMEL_US_TXDIS (1 << 7) /* Transmitter Disable */
-#define ATMEL_US_RSTSTA (1 << 8) /* Reset Status Bits */
-#define ATMEL_US_STTBRK (1 << 9) /* Start Break */
-#define ATMEL_US_STPBRK (1 << 10) /* Stop Break */
-#define ATMEL_US_STTTO (1 << 11) /* Start Time-out */
-#define ATMEL_US_SENDA (1 << 12) /* Send Address */
-#define ATMEL_US_RSTIT (1 << 13) /* Reset Iterations */
-#define ATMEL_US_RSTNACK (1 << 14) /* Reset Non Acknowledge */
-#define ATMEL_US_RETTO (1 << 15) /* Rearm Time-out */
-#define ATMEL_US_DTREN (1 << 16) /* Data Terminal Ready Enable [AT91RM9200 only] */
-#define ATMEL_US_DTRDIS (1 << 17) /* Data Terminal Ready Disable [AT91RM9200 only] */
-#define ATMEL_US_RTSEN (1 << 18) /* Request To Send Enable */
-#define ATMEL_US_RTSDIS (1 << 19) /* Request To Send Disable */
+#define ATMEL_US_CR 0x00 /* Control Register */
+#define ATMEL_US_RSTRX BIT(2) /* Reset Receiver */
+#define ATMEL_US_RSTTX BIT(3) /* Reset Transmitter */
+#define ATMEL_US_RXEN BIT(4) /* Receiver Enable */
+#define ATMEL_US_RXDIS BIT(5) /* Receiver Disable */
+#define ATMEL_US_TXEN BIT(6) /* Transmitter Enable */
+#define ATMEL_US_TXDIS BIT(7) /* Transmitter Disable */
+#define ATMEL_US_RSTSTA BIT(8) /* Reset Status Bits */
+#define ATMEL_US_STTBRK BIT(9) /* Start Break */
+#define ATMEL_US_STPBRK BIT(10) /* Stop Break */
+#define ATMEL_US_STTTO BIT(11) /* Start Time-out */
+#define ATMEL_US_SENDA BIT(12) /* Send Address */
+#define ATMEL_US_RSTIT BIT(13) /* Reset Iterations */
+#define ATMEL_US_RSTNACK BIT(14) /* Reset Non Acknowledge */
+#define ATMEL_US_RETTO BIT(15) /* Rearm Time-out */
+#define ATMEL_US_DTREN BIT(16) /* Data Terminal Ready Enable */
+#define ATMEL_US_DTRDIS BIT(17) /* Data Terminal Ready Disable */
+#define ATMEL_US_RTSEN BIT(18) /* Request To Send Enable */
+#define ATMEL_US_RTSDIS BIT(19) /* Request To Send Disable */
-#define ATMEL_US_MR 0x04 /* Mode Register */
-#define ATMEL_US_USMODE (0xf << 0) /* Mode of the USART */
-#define ATMEL_US_USMODE_NORMAL 0
-#define ATMEL_US_USMODE_RS485 1
-#define ATMEL_US_USMODE_HWHS 2
-#define ATMEL_US_USMODE_MODEM 3
-#define ATMEL_US_USMODE_ISO7816_T0 4
-#define ATMEL_US_USMODE_ISO7816_T1 6
-#define ATMEL_US_USMODE_IRDA 8
-#define ATMEL_US_USCLKS (3 << 4) /* Clock Selection */
-#define ATMEL_US_USCLKS_MCK (0 << 4)
-#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
-#define ATMEL_US_USCLKS_SCK (3 << 4)
-#define ATMEL_US_CHRL (3 << 6) /* Character Length */
-#define ATMEL_US_CHRL_5 (0 << 6)
-#define ATMEL_US_CHRL_6 (1 << 6)
-#define ATMEL_US_CHRL_7 (2 << 6)
-#define ATMEL_US_CHRL_8 (3 << 6)
-#define ATMEL_US_SYNC (1 << 8) /* Synchronous Mode Select */
-#define ATMEL_US_PAR (7 << 9) /* Parity Type */
-#define ATMEL_US_PAR_EVEN (0 << 9)
-#define ATMEL_US_PAR_ODD (1 << 9)
-#define ATMEL_US_PAR_SPACE (2 << 9)
-#define ATMEL_US_PAR_MARK (3 << 9)
-#define ATMEL_US_PAR_NONE (4 << 9)
-#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
-#define ATMEL_US_NBSTOP (3 << 12) /* Number of Stop Bits */
-#define ATMEL_US_NBSTOP_1 (0 << 12)
-#define ATMEL_US_NBSTOP_1_5 (1 << 12)
-#define ATMEL_US_NBSTOP_2 (2 << 12)
-#define ATMEL_US_CHMODE (3 << 14) /* Channel Mode */
-#define ATMEL_US_CHMODE_NORMAL (0 << 14)
-#define ATMEL_US_CHMODE_ECHO (1 << 14)
-#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
-#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
-#define ATMEL_US_MSBF (1 << 16) /* Bit Order */
-#define ATMEL_US_MODE9 (1 << 17) /* 9-bit Character Length */
-#define ATMEL_US_CLKO (1 << 18) /* Clock Output Select */
-#define ATMEL_US_OVER (1 << 19) /* Oversampling Mode */
-#define ATMEL_US_INACK (1 << 20) /* Inhibit Non Acknowledge */
-#define ATMEL_US_DSNACK (1 << 21) /* Disable Successive NACK */
-#define ATMEL_US_MAX_ITER (7 << 24) /* Max Iterations */
-#define ATMEL_US_FILTER (1 << 28) /* Infrared Receive Line Filter */
+#define ATMEL_US_MR 0x04 /* Mode Register */
+#define ATMEL_US_USMODE GENMASK(3, 0) /* Mode of the USART */
+#define ATMEL_US_USMODE_NORMAL 0
+#define ATMEL_US_USMODE_RS485 1
+#define ATMEL_US_USMODE_HWHS 2
+#define ATMEL_US_USMODE_MODEM 3
+#define ATMEL_US_USMODE_ISO7816_T0 4
+#define ATMEL_US_USMODE_ISO7816_T1 6
+#define ATMEL_US_USMODE_IRDA 8
+#define ATMEL_US_USCLKS GENMASK(5, 4) /* Clock Selection */
+#define ATMEL_US_USCLKS_MCK (0 << 4)
+#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
+#define ATMEL_US_USCLKS_SCK (3 << 4)
+#define ATMEL_US_CHRL GENMASK(7, 6) /* Character Length */
+#define ATMEL_US_CHRL_5 (0 << 6)
+#define ATMEL_US_CHRL_6 (1 << 6)
+#define ATMEL_US_CHRL_7 (2 << 6)
+#define ATMEL_US_CHRL_8 (3 << 6)
+#define ATMEL_US_SYNC BIT(8) /* Synchronous Mode Select */
+#define ATMEL_US_PAR GENMASK(11, 9) /* Parity Type */
+#define ATMEL_US_PAR_EVEN (0 << 9)
+#define ATMEL_US_PAR_ODD (1 << 9)
+#define ATMEL_US_PAR_SPACE (2 << 9)
+#define ATMEL_US_PAR_MARK (3 << 9)
+#define ATMEL_US_PAR_NONE (4 << 9)
+#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
+#define ATMEL_US_NBSTOP GENMASK(13, 12) /* Number of Stop Bits */
+#define ATMEL_US_NBSTOP_1 (0 << 12)
+#define ATMEL_US_NBSTOP_1_5 (1 << 12)
+#define ATMEL_US_NBSTOP_2 (2 << 12)
+#define ATMEL_US_CHMODE GENMASK(15, 14) /* Channel Mode */
+#define ATMEL_US_CHMODE_NORMAL (0 << 14)
+#define ATMEL_US_CHMODE_ECHO (1 << 14)
+#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
+#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
+#define ATMEL_US_MSBF BIT(16) /* Bit Order */
+#define ATMEL_US_MODE9 BIT(17) /* 9-bit Character Length */
+#define ATMEL_US_CLKO BIT(18) /* Clock Output Select */
+#define ATMEL_US_OVER BIT(19) /* Oversampling Mode */
+#define ATMEL_US_INACK BIT(20) /* Inhibit Non Acknowledge */
+#define ATMEL_US_DSNACK BIT(21) /* Disable Successive NACK */
+#define ATMEL_US_MAX_ITER GENMASK(26, 24) /* Max Iterations */
+#define ATMEL_US_FILTER BIT(28) /* Infrared Receive Line Filter */
-#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
-#define ATMEL_US_RXRDY (1 << 0) /* Receiver Ready */
-#define ATMEL_US_TXRDY (1 << 1) /* Transmitter Ready */
-#define ATMEL_US_RXBRK (1 << 2) /* Break Received / End of Break */
-#define ATMEL_US_ENDRX (1 << 3) /* End of Receiver Transfer */
-#define ATMEL_US_ENDTX (1 << 4) /* End of Transmitter Transfer */
-#define ATMEL_US_OVRE (1 << 5) /* Overrun Error */
-#define ATMEL_US_FRAME (1 << 6) /* Framing Error */
-#define ATMEL_US_PARE (1 << 7) /* Parity Error */
-#define ATMEL_US_TIMEOUT (1 << 8) /* Receiver Time-out */
-#define ATMEL_US_TXEMPTY (1 << 9) /* Transmitter Empty */
-#define ATMEL_US_ITERATION (1 << 10) /* Max number of Repetitions Reached */
-#define ATMEL_US_TXBUFE (1 << 11) /* Transmission Buffer Empty */
-#define ATMEL_US_RXBUFF (1 << 12) /* Reception Buffer Full */
-#define ATMEL_US_NACK (1 << 13) /* Non Acknowledge */
-#define ATMEL_US_RIIC (1 << 16) /* Ring Indicator Input Change [AT91RM9200 only] */
-#define ATMEL_US_DSRIC (1 << 17) /* Data Set Ready Input Change [AT91RM9200 only] */
-#define ATMEL_US_DCDIC (1 << 18) /* Data Carrier Detect Input Change [AT91RM9200 only] */
-#define ATMEL_US_CTSIC (1 << 19) /* Clear to Send Input Change */
-#define ATMEL_US_RI (1 << 20) /* RI */
-#define ATMEL_US_DSR (1 << 21) /* DSR */
-#define ATMEL_US_DCD (1 << 22) /* DCD */
-#define ATMEL_US_CTS (1 << 23) /* CTS */
+#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
+#define ATMEL_US_RXRDY BIT(0) /* Receiver Ready */
+#define ATMEL_US_TXRDY BIT(1) /* Transmitter Ready */
+#define ATMEL_US_RXBRK BIT(2) /* Break Received / End of Break */
+#define ATMEL_US_ENDRX BIT(3) /* End of Receiver Transfer */
+#define ATMEL_US_ENDTX BIT(4) /* End of Transmitter Transfer */
+#define ATMEL_US_OVRE BIT(5) /* Overrun Error */
+#define ATMEL_US_FRAME BIT(6) /* Framing Error */
+#define ATMEL_US_PARE BIT(7) /* Parity Error */
+#define ATMEL_US_TIMEOUT BIT(8) /* Receiver Time-out */
+#define ATMEL_US_TXEMPTY BIT(9) /* Transmitter Empty */
+#define ATMEL_US_ITERATION BIT(10) /* Max number of Repetitions Reached */
+#define ATMEL_US_TXBUFE BIT(11) /* Transmission Buffer Empty */
+#define ATMEL_US_RXBUFF BIT(12) /* Reception Buffer Full */
+#define ATMEL_US_NACK BIT(13) /* Non Acknowledge */
+#define ATMEL_US_RIIC BIT(16) /* Ring Indicator Input Change */
+#define ATMEL_US_DSRIC BIT(17) /* Data Set Ready Input Change */
+#define ATMEL_US_DCDIC BIT(18) /* Data Carrier Detect Input Change */
+#define ATMEL_US_CTSIC BIT(19) /* Clear to Send Input Change */
+#define ATMEL_US_RI BIT(20) /* RI */
+#define ATMEL_US_DSR BIT(21) /* DSR */
+#define ATMEL_US_DCD BIT(22) /* DCD */
+#define ATMEL_US_CTS BIT(23) /* CTS */
-#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
-#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
-#define ATMEL_US_CSR 0x14 /* Channel Status Register */
-#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
-#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
-#define ATMEL_US_SYNH (1 << 15) /* Transmit/Receive Sync [AT91SAM9261 only] */
+#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
+#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
+#define ATMEL_US_CSR 0x14 /* Channel Status Register */
+#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
+#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
+#define ATMEL_US_SYNH BIT(15) /* Transmit/Receive Sync */
-#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
-#define ATMEL_US_CD (0xffff << 0) /* Clock Divider */
+#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
+#define ATMEL_US_CD GENMASK(15, 0) /* Clock Divider */
-#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
-#define ATMEL_US_TO (0xffff << 0) /* Time-out Value */
+#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
+#define ATMEL_US_TO GENMASK(15, 0) /* Time-out Value */
-#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
-#define ATMEL_US_TG (0xff << 0) /* Timeguard Value */
+#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
+#define ATMEL_US_TG GENMASK(7, 0) /* Timeguard Value */
-#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
-#define ATMEL_US_NER 0x44 /* Number of Errors Register */
-#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
+#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
+#define ATMEL_US_NER 0x44 /* Number of Errors Register */
+#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
-#define ATMEL_US_NAME 0xf0 /* Ip Name */
-#define ATMEL_US_VERSION 0xfc /* Ip Version */
+#define ATMEL_US_NAME 0xf0 /* Ip Name */
+#define ATMEL_US_VERSION 0xfc /* Ip Version */
#endif
--
1.8.2.2
next prev parent reply other threads:[~2015-06-11 16:20 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-11 16:20 [PATCH linux-next v2 0/4] tty/serial: at91: add support to FIFOs Cyrille Pitchen
2015-06-11 16:20 ` Cyrille Pitchen
2015-06-11 16:20 ` Cyrille Pitchen
2015-06-11 16:20 ` [PATCH linux-next v2 1/4] ARM: at91/dt: add a new DT property to support FIFOs on Atmel USARTs Cyrille Pitchen
2015-06-11 16:20 ` Cyrille Pitchen
2015-06-11 16:20 ` Cyrille Pitchen
2015-06-18 16:39 ` Alexandre Belloni
2015-06-18 16:39 ` Alexandre Belloni
2015-06-29 13:00 ` Nicolas Ferre
2015-06-29 13:00 ` Nicolas Ferre
2015-06-29 13:00 ` Nicolas Ferre
2015-06-11 16:20 ` Cyrille Pitchen [this message]
2015-06-11 16:20 ` [PATCH linux-next v2 2/4] tty/serial: at91: fix some macro definitions to fit coding style Cyrille Pitchen
2015-06-11 16:20 ` Cyrille Pitchen
2015-06-18 16:39 ` Alexandre Belloni
2015-06-18 16:39 ` Alexandre Belloni
2015-06-18 16:39 ` Alexandre Belloni
2015-06-29 13:00 ` Nicolas Ferre
2015-06-29 13:00 ` Nicolas Ferre
2015-06-29 13:00 ` Nicolas Ferre
2015-06-11 16:20 ` [PATCH linux-next v2 3/4] tty/serial: at91: add support to FIFOs Cyrille Pitchen
2015-06-11 16:20 ` Cyrille Pitchen
2015-06-11 16:20 ` Cyrille Pitchen
2015-06-18 16:36 ` Alexandre Belloni
2015-06-18 16:36 ` Alexandre Belloni
2015-06-18 16:36 ` Alexandre Belloni
2015-06-29 13:11 ` Nicolas Ferre
2015-06-29 13:11 ` Nicolas Ferre
2015-06-29 13:11 ` Nicolas Ferre
2015-06-11 16:20 ` [PATCH linux-next v2 4/4] tty/serial: at91: use 32bit writes into TX FIFO when DMA is enabled Cyrille Pitchen
2015-06-11 16:20 ` Cyrille Pitchen
2015-06-11 16:20 ` Cyrille Pitchen
2015-06-29 13:28 ` Nicolas Ferre
2015-06-29 13:28 ` Nicolas Ferre
2015-06-29 13:28 ` Nicolas Ferre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=f22220ee42ecf9301def7e90154b74937ca9ffab.1434038494.git.cyrille.pitchen@atmel.com \
--to=cyrille.pitchen@atmel.com \
--cc=alexandre.belloni@free-electrons.com \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=gregkh@linuxfoundation.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=josh.wu@atmel.com \
--cc=leilei.zhao@atmel.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=ludovic.desroches@atmel.com \
--cc=mark.rutland@arm.com \
--cc=nicolas.ferre@atmel.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=wenyou.yang@atmel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.