[PATCH 0/3] arm64: dts: qcom: sm8450-hdk: add sound support

[PATCH 0/3] arm64: dts: qcom: sm8450-hdk: add sound support

[Krzysztof Kozlowski]

Hi,

Initial work (still partially in progress) adding audio to HDK8450 board.

Working/tested:
 - speakers
 - one channel of headset

The DTS patches do not have particular dependencies, however they:
1. Use updated ASoC bindings:
   https://lore.kernel.org/linux-arm-msm/20221111113547.100442-1-krzysztof.kozlowski@linaro.org/T/#t

2. For full operation need changes in Soundwire and Qualcomm ASoC drivers, not
   yet upstreamed:
   https://github.com/krzk/linux/commits/wip/sm8450
   Booting remoteproc without these changes will report errors, but these are
   expected at this stage.

Best regards,
Krzysztof

Srinivas Kandagatla (3):
  arm64: dts: qcom: sm8450: add GPR node
  arm64: dts: qcom: sm8450: add Soundwire and LPASS
  arm64: dts: qcom: sm8450-hdk: add sound support

 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 161 ++++++++++++
 arch/arm64/boot/dts/qcom/sm8450.dtsi    | 335 ++++++++++++++++++++++++
 2 files changed, 496 insertions(+)

-- 
2.34.1

[PATCH 1/3] arm64: dts: qcom: sm8450: add GPR node

[Krzysztof Kozlowski]

From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

Add Generic Packet Router (GPR) device node with ADSP services.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 40 ++++++++++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 46f9576f786f..4b0a1eee8bd9 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/interconnect/qcom,sm8450.h>
+#include <dt-bindings/soc/qcom,gpr.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 #include <dt-bindings/thermal/thermal.h>
 
@@ -2134,6 +2135,45 @@ IPCC_MPROC_SIGNAL_GLINK_QMP
 				label = "lpass";
 				qcom,remote-pid = <2>;
 
+				gpr {
+					compatible = "qcom,gpr";
+					qcom,glink-channels = "adsp_apps";
+					qcom,domain = <GPR_DOMAIN_ID_ADSP>;
+					qcom,intents = <512 20>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					q6apm: service@1 {
+						reg = <GPR_APM_MODULE_IID>;
+						compatible = "qcom,q6apm";
+						#sound-dai-cells = <0>;
+						qcom,protection-domain = "avs/audio",
+									 "msm/adsp/audio_pd";
+
+						q6apmdai: dais {
+							compatible = "qcom,q6apm-dais";
+							iommus = <&apps_smmu 0x1801 0x0>;
+						};
+
+						q6apmbedai: bedais {
+							compatible = "qcom,q6apm-lpass-dais";
+							#sound-dai-cells = <1>;
+						};
+					};
+
+					q6prm: service@2 {
+						reg = <GPR_PRM_MODULE_IID>;
+						compatible = "qcom,q6prm";
+						qcom,protection-domain = "avs/audio",
+									 "msm/adsp/audio_pd";
+
+						q6prmcc: clock-controller {
+							compatible = "qcom,q6prm-lpass-clocks";
+							#clock-cells = <2>;
+						};
+					};
+				};
+
 				fastrpc {
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
-- 
2.34.1

[PATCH 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS

[Krzysztof Kozlowski]

From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

Add Soundwire controllers, Low Power Audio SubSystem (LPASS) devices and
LPASS pin controller.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 295 +++++++++++++++++++++++++++
 1 file changed, 295 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 4b0a1eee8bd9..c99740591467 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -15,6 +15,7 @@
 #include <dt-bindings/interconnect/qcom,sm8450.h>
 #include <dt-bindings/soc/qcom,gpr.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -2097,6 +2098,212 @@ compute-cb@3 {
 			};
 		};
 
+		wsa2macro: codec@31e0000 {
+			compatible = "qcom,sm8450-lpass-wsa-macro";
+			reg = <0 0x031e0000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&vamacro>;
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+					  <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>, <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "wsa2-mclk";
+			#sound-dai-cells = <1>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&wsa2_swr_active>;
+		};
+
+		/* WSA2 */
+		swr4: soundwire-controller@31f0000 {
+			reg = <0 0x031f0000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.7.0";
+			interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&wsa2macro>;
+			clock-names = "iface";
+
+			qcom,din-ports = <2>;
+			qcom,dout-ports = <6>;
+
+			qcom,ports-sinterval-low =	/bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
+			qcom,ports-offset1 =		/bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
+			qcom,ports-offset2 =		/bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-hstop =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-word-length =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0xFF 0x01 0xFF 0xFF 0x01 0xFF 0xFF>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-lane-control =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		rxmacro: codec@3200000 {
+			compatible = "qcom,sm8450-lpass-rx-macro";
+			reg = <0 0x3200000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&vamacro>;
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>, <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "mclk";
+			#sound-dai-cells = <1>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&rx_swr_active>;
+		};
+
+		swr1: soundwire-controller@3210000 {
+			reg = <0 0x3210000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.7.0";
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rxmacro>;
+			clock-names = "iface";
+			label = "RX";
+			qcom,din-ports = <0>;
+			qcom,dout-ports = <5>;
+
+			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x1F 0x1F 0x07 0x00>;
+			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0B 0x01 0x00>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0B 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xFF 0x03 0xFF 0xFF 0xFF>;
+			qcom,ports-hstop =		/bits/ 8 <0xFF 0x06 0xFF 0xFF 0xFF>;
+			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xFF 0xFF>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0x00 0x01 0xFF 0xFF>;
+			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0x00>;
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		txmacro: codec@3220000 {
+			compatible = "qcom,sm8450-lpass-tx-macro";
+			reg = <0 0x3220000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&vamacro>;
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+					   <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>, <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "mclk";
+			#sound-dai-cells = <1>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&tx_swr_active>;
+		};
+
+		wsamacro: codec@3240000 {
+			compatible = "qcom,sm8450-lpass-wsa-macro";
+			reg = <0 0x03240000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&vamacro>;
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+					  <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>, <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "mclk";
+			#sound-dai-cells = <1>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&wsa_swr_active>;
+		};
+
+		/* WSA */
+		swr0: soundwire-controller@3250000 {
+			reg = <0 0x03250000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.7.0";
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&wsamacro>;
+			clock-names = "iface";
+
+			qcom,din-ports = <2>;
+			qcom,dout-ports = <6>;
+
+			qcom,ports-sinterval-low =	/bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
+			qcom,ports-offset1 =		/bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
+			qcom,ports-offset2 =		/bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-hstop =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-word-length =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0xFF 0x01 0xFF 0xFF 0x01 0xFF 0xFF>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-lane-control =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,port-offset = <1>;
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		swr2: soundwire-controller@33b0000 {
+			reg = <0 0x33b0000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.7.0";
+			interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "core", "wake";
+
+			clocks = <&vamacro>;
+			clock-names = "iface";
+			label = "TX";
+
+			qcom,din-ports = <4>;
+			qcom,dout-ports = <0>;
+			qcom,ports-sinterval-low =	/bits/ 8 <0x01 0x01 0x03 0x03>;
+			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x01 0x01>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x00 0x00>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-hstart =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-hstop =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-word-length =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-lane-control =	/bits/ 8 <0x01 0x02 0x00 0x00>;
+			qcom,port-offset = <1>;
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		vamacro: codec@33f0000 {
+			compatible = "qcom,sm8450-lpass-va-macro";
+			reg = <0 0x033f0000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			clock-names = "mclk", "macro", "dcodec", "npl";
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "fsgen";
+			#sound-dai-cells = <1>;
+		};
+
 		remoteproc_adsp: remoteproc@30000000 {
 			compatible = "qcom,sm8450-adsp-pas";
 			reg = <0 0x030000000 0 0x100>;
@@ -3030,6 +3237,91 @@ qup_uart20_default: qup-uart20-default-state {
 
 		};
 
+		lpass_tlmm: pinctrl@3440000{
+			compatible = "qcom,sm8450-lpass-lpi-pinctrl";
+			reg = <0 0x3440000 0x0 0x20000>,
+			      <0 0x34d0000 0x0 0x10000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&lpass_tlmm 0 0 23>;
+
+			clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			clock-names = "core", "audio";
+
+			wsa_swr_active: wsa-swr-active-state {
+				clk-pins {
+					pins = "gpio10";
+					function = "wsa_swr_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data-pins {
+					pins = "gpio11";
+					function = "wsa_swr_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+
+			tx_swr_active: tx-swr-active-state {
+				clk-pins {
+					pins = "gpio0";
+					function = "swr_tx_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data-pins {
+					pins = "gpio1", "gpio2", "gpio14";
+					function = "swr_tx_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+
+			rx_swr_active: rx-swr-active-state {
+				clk-pins {
+					pins = "gpio3";
+					function = "swr_rx_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data-pins {
+					pins = "gpio4", "gpio5";
+					function = "swr_rx_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+
+			wsa2_swr_active: wsa2-swr-active-state {
+				clk-pins {
+					pins = "gpio15";
+					function = "wsa2_swr_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data-pins {
+					pins = "gpio16";
+					function = "wsa2_swr_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+		};
+
 		apps_smmu: iommu@15000000 {
 			compatible = "qcom,sm8450-smmu-500", "arm,mmu-500";
 			reg = <0 0x15000000 0 0x100000>;
@@ -3507,6 +3799,9 @@ lpass_ag_noc: interconnect@3c40000 {
 		};
 	};
 
+	sound: sound {
+	};
+
 	thermal-zones {
 		aoss0-thermal {
 			polling-delay-passive = <0>;
-- 
2.34.1

[PATCH 3/3] arm64: dts: qcom: sm8450-hdk: add sound support

[Krzysztof Kozlowski]

From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

Add sound support to SM8450 HDK board.  Tested setup so far is only two
speakers (working) and head-phones (only one channel working).

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 161 ++++++++++++++++++++++++
 1 file changed, 161 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 4d75f9db08c2..c177283b6764 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -6,6 +6,8 @@
 /dts-v1/;
 
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
 #include "sm8450.dtsi"
 
 / {
@@ -421,6 +423,147 @@ &uart7 {
 	status = "okay";
 };
 
+&soc {
+	wcd938x: codec {
+		compatible = "qcom,wcd9380-codec";
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
+		#sound-dai-cells = <1>;
+
+		vdd-buck-supply = <&vreg_s10b_1p8>;
+		vdd-rxtx-supply = <&vreg_s10b_1p8>;
+		vdd-io-supply = <&vreg_s10b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob>;
+	};
+};
+
+&sound {
+	compatible = "qcom,sm8450-sndcard";
+	model = "SM8450-HDK";
+	audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
+			"SpkrRight IN", "WSA_SPK2 OUT",
+			"IN1_HPHL", "HPHL_OUT",
+			"IN2_HPHR", "HPHR_OUT",
+			"AMIC1", "MIC BIAS1",
+			"AMIC2", "MIC BIAS2",
+			"AMIC3", "MIC BIAS3",
+			"AMIC4", "MIC BIAS3",
+			"AMIC5", "MIC BIAS4";
+
+	wcd-playback-dai-link {
+		link-name = "WCD Playback";
+		cpu {
+			sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+		};
+
+		codec {
+			sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
+		};
+
+		platform {
+			sound-dai = <&q6apm>;
+		};
+	};
+
+	wcd-playback-dai-link {
+		link-name = "WCD Playback";
+		cpu {
+			sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+		};
+
+		codec {
+			sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
+		};
+
+		platform {
+			sound-dai = <&q6apm>;
+		};
+	};
+
+	wsa-dai-link {
+		link-name = "WSA Playback";
+		cpu {
+			sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+		};
+
+		codec {
+			sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>;
+		};
+
+		platform {
+			sound-dai = <&q6apm>;
+		};
+	};
+
+	va-dai-link {
+		link-name = "VA Capture";
+		cpu {
+			sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+		};
+
+		platform {
+			sound-dai = <&q6apm>;
+		};
+	};
+};
+
+&swr0 {
+	right_spkr: speaker@0,1{
+		compatible = "sdw10217020200";
+		reg = <0 1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spkr_1_sd_n_active>;
+		powerdown-gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		#thermal-sensor-cells = <0>;
+		vdd-supply = <&vreg_s10b_1p8>;
+	};
+
+	left_spkr: speaker@0,2{
+		compatible = "sdw10217020200";
+		reg = <0 2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spkr_2_sd_n_active>;
+		powerdown-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		#thermal-sensor-cells = <0>;
+		vdd-supply = <&vreg_s10b_1p8>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		/* ports: adc1_2, adc3_4, dmic0_3_mbhc, dmic4_7 */
+		qcom,tx-port-mapping = <1 1 2 3>;
+	};
+};
+
 &ufs_mem_hc {
 	status = "okay";
 
@@ -461,3 +604,21 @@ &usb_1_qmpphy {
 	vdda-phy-supply = <&vreg_l6b_1p2>;
 	vdda-pll-supply = <&vreg_l1b_0p91>;
 };
+
+&tlmm {
+	spkr_1_sd_n_active: spkr-1-sd-n-active-state {
+		pins = "gpio1";
+		function = "gpio";
+		drive-strength = <4>;
+		bias-disable;
+		output-low;
+	};
+
+	spkr_2_sd_n_active: spkr-2-sd-n-active-state {
+		pins = "gpio89";
+		function = "gpio";
+		drive-strength = <4>;
+		bias-disable;
+		output-low;
+	};
+};
-- 
2.34.1

Re: [PATCH 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS

[Konrad Dybcio]

On 14/11/2022 16:21, Krzysztof Kozlowski wrote:
> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>
> Add Soundwire controllers, Low Power Audio SubSystem (LPASS) devices and
> LPASS pin controller.
>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sm8450.dtsi | 295 +++++++++++++++++++++++++++
>   1 file changed, 295 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 4b0a1eee8bd9..c99740591467 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -15,6 +15,7 @@
>   #include <dt-bindings/interconnect/qcom,sm8450.h>
>   #include <dt-bindings/soc/qcom,gpr.h>
>   #include <dt-bindings/soc/qcom,rpmh-rsc.h>
> +#include <dt-bindings/sound/qcom,q6afe.h>
>   #include <dt-bindings/thermal/thermal.h>
>   
>   / {
> @@ -2097,6 +2098,212 @@ compute-cb@3 {
>   			};
>   		};
>   
> +		wsa2macro: codec@31e0000 {
> +			compatible = "qcom,sm8450-lpass-wsa-macro";
> +			reg = <0 0x031e0000 0 0x1000>;
The sorting will be off, as adsp and cdsp have been mistakenly put in
the wrong place (notice adsp @ 32300000 is actually at an address
that's 8 hex digits long, but the reg addr is padded to 9 hex digits..).

Could you submit a fix for that as well?

> +			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&vamacro>;
> +			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> +			assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +					  <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;

Remove the duplicated space before LPASS_CLK_ATTRIBUTE_COUPLE_NO.


> +			assigned-clock-rates = <19200000>, <19200000>;
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "wsa2-mclk";
> +			#sound-dai-cells = <1>;
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&wsa2_swr_active>;
> +		};
> +
> +		/* WSA2 */
> +		swr4: soundwire-controller@31f0000 {
> +			reg = <0 0x031f0000 0 0x2000>;
> +			compatible = "qcom,soundwire-v1.7.0";
> +			interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&wsa2macro>;
> +			clock-names = "iface";
> +
> +			qcom,din-ports = <2>;
> +			qcom,dout-ports = <6>;
> +
> +			qcom,ports-sinterval-low =	/bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
> +			qcom,ports-offset1 =		/bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
> +			qcom,ports-offset2 =		/bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
> +			qcom,ports-hstart =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;

Please avoid mixing upper- and lowercase hex throughout the file.


Konrad

> +			qcom,ports-hstop =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-word-length =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0xFF 0x01 0xFF 0xFF 0x01 0xFF 0xFF>;
> +			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-lane-control =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
> +
> +			#sound-dai-cells = <1>;
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +		};
> +
> +		rxmacro: codec@3200000 {
> +			compatible = "qcom,sm8450-lpass-rx-macro";
> +			reg = <0 0x3200000 0 0x1000>;
> +			clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&vamacro>;
> +			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> +
> +			assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			assigned-clock-rates = <19200000>, <19200000>;
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "mclk";
> +			#sound-dai-cells = <1>;
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&rx_swr_active>;
> +		};
> +
> +		swr1: soundwire-controller@3210000 {
> +			reg = <0 0x3210000 0 0x2000>;
> +			compatible = "qcom,soundwire-v1.7.0";
> +			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&rxmacro>;
> +			clock-names = "iface";
> +			label = "RX";
> +			qcom,din-ports = <0>;
> +			qcom,dout-ports = <5>;
> +
> +			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x1F 0x1F 0x07 0x00>;
> +			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0B 0x01 0x00>;
> +			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0B 0x00 0x00>;
> +			qcom,ports-hstart =		/bits/ 8 <0xFF 0x03 0xFF 0xFF 0xFF>;
> +			qcom,ports-hstop =		/bits/ 8 <0xFF 0x06 0xFF 0xFF 0xFF>;
> +			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xFF 0xFF>;
> +			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0x00 0x01 0xFF 0xFF>;
> +			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
> +			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0x00>;
> +			#sound-dai-cells = <1>;
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +		};
> +
> +		txmacro: codec@3220000 {
> +			compatible = "qcom,sm8450-lpass-tx-macro";
> +			reg = <0 0x3220000 0 0x1000>;
> +			clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&vamacro>;
> +			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> +			assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +					   <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			assigned-clock-rates = <19200000>, <19200000>;
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "mclk";
> +			#sound-dai-cells = <1>;
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&tx_swr_active>;
> +		};
> +
> +		wsamacro: codec@3240000 {
> +			compatible = "qcom,sm8450-lpass-wsa-macro";
> +			reg = <0 0x03240000 0 0x1000>;
> +			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&vamacro>;
> +			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> +
> +			assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +					  <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			assigned-clock-rates = <19200000>, <19200000>;
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "mclk";
> +			#sound-dai-cells = <1>;
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&wsa_swr_active>;
> +		};
> +
> +		/* WSA */
> +		swr0: soundwire-controller@3250000 {
> +			reg = <0 0x03250000 0 0x2000>;
> +			compatible = "qcom,soundwire-v1.7.0";
> +			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&wsamacro>;
> +			clock-names = "iface";
> +
> +			qcom,din-ports = <2>;
> +			qcom,dout-ports = <6>;
> +
> +			qcom,ports-sinterval-low =	/bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
> +			qcom,ports-offset1 =		/bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
> +			qcom,ports-offset2 =		/bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
> +			qcom,ports-hstart =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-hstop =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-word-length =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0xFF 0x01 0xFF 0xFF 0x01 0xFF 0xFF>;
> +			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-lane-control =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
> +			qcom,port-offset = <1>;
> +			#sound-dai-cells = <1>;
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +		};
> +
> +		swr2: soundwire-controller@33b0000 {
> +			reg = <0 0x33b0000 0 0x2000>;
> +			compatible = "qcom,soundwire-v1.7.0";
> +			interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&intc GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "core", "wake";
> +
> +			clocks = <&vamacro>;
> +			clock-names = "iface";
> +			label = "TX";
> +
> +			qcom,din-ports = <4>;
> +			qcom,dout-ports = <0>;
> +			qcom,ports-sinterval-low =	/bits/ 8 <0x01 0x01 0x03 0x03>;
> +			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x01 0x01>;
> +			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x00 0x00>;
> +			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-hstart =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-hstop =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-word-length =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
> +			qcom,ports-lane-control =	/bits/ 8 <0x01 0x02 0x00 0x00>;
> +			qcom,port-offset = <1>;
> +			#sound-dai-cells = <1>;
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +		};
> +
> +		vamacro: codec@33f0000 {
> +			compatible = "qcom,sm8450-lpass-va-macro";
> +			reg = <0 0x033f0000 0 0x1000>;
> +			clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			clock-names = "mclk", "macro", "dcodec", "npl";
> +			assigned-clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			assigned-clock-rates = <19200000>;
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "fsgen";
> +			#sound-dai-cells = <1>;
> +		};
> +
>   		remoteproc_adsp: remoteproc@30000000 {
>   			compatible = "qcom,sm8450-adsp-pas";
>   			reg = <0 0x030000000 0 0x100>;
> @@ -3030,6 +3237,91 @@ qup_uart20_default: qup-uart20-default-state {
>   
>   		};
>   
> +		lpass_tlmm: pinctrl@3440000{
> +			compatible = "qcom,sm8450-lpass-lpi-pinctrl";
> +			reg = <0 0x3440000 0x0 0x20000>,
> +			      <0 0x34d0000 0x0 0x10000>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			gpio-ranges = <&lpass_tlmm 0 0 23>;
> +
> +			clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			clock-names = "core", "audio";
> +
> +			wsa_swr_active: wsa-swr-active-state {
> +				clk-pins {
> +					pins = "gpio10";
> +					function = "wsa_swr_clk";
> +					drive-strength = <2>;
> +					slew-rate = <1>;
> +					bias-disable;
> +				};
> +
> +				data-pins {
> +					pins = "gpio11";
> +					function = "wsa_swr_data";
> +					drive-strength = <2>;
> +					slew-rate = <1>;
> +					bias-bus-hold;
> +				};
> +			};
> +
> +			tx_swr_active: tx-swr-active-state {
> +				clk-pins {
> +					pins = "gpio0";
> +					function = "swr_tx_clk";
> +					drive-strength = <2>;
> +					slew-rate = <1>;
> +					bias-disable;
> +				};
> +
> +				data-pins {
> +					pins = "gpio1", "gpio2", "gpio14";
> +					function = "swr_tx_data";
> +					drive-strength = <2>;
> +					slew-rate = <1>;
> +					bias-bus-hold;
> +				};
> +			};
> +
> +			rx_swr_active: rx-swr-active-state {
> +				clk-pins {
> +					pins = "gpio3";
> +					function = "swr_rx_clk";
> +					drive-strength = <2>;
> +					slew-rate = <1>;
> +					bias-disable;
> +				};
> +
> +				data-pins {
> +					pins = "gpio4", "gpio5";
> +					function = "swr_rx_data";
> +					drive-strength = <2>;
> +					slew-rate = <1>;
> +					bias-bus-hold;
> +				};
> +			};
> +
> +			wsa2_swr_active: wsa2-swr-active-state {
> +				clk-pins {
> +					pins = "gpio15";
> +					function = "wsa2_swr_clk";
> +					drive-strength = <2>;
> +					slew-rate = <1>;
> +					bias-disable;
> +				};
> +
> +				data-pins {
> +					pins = "gpio16";
> +					function = "wsa2_swr_data";
> +					drive-strength = <2>;
> +					slew-rate = <1>;
> +					bias-bus-hold;
> +				};
> +			};
> +		};
> +
>   		apps_smmu: iommu@15000000 {
>   			compatible = "qcom,sm8450-smmu-500", "arm,mmu-500";
>   			reg = <0 0x15000000 0 0x100000>;
> @@ -3507,6 +3799,9 @@ lpass_ag_noc: interconnect@3c40000 {
>   		};
>   	};
>   
> +	sound: sound {
> +	};
> +
>   	thermal-zones {
>   		aoss0-thermal {
>   			polling-delay-passive = <0>;

Re: [PATCH 3/3] arm64: dts: qcom: sm8450-hdk: add sound support

[Konrad Dybcio]

On 14/11/2022 16:21, Krzysztof Kozlowski wrote:
> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>
> Add sound support to SM8450 HDK board.  Tested setup so far is only two
> speakers (working) and head-phones (only one channel working).
>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 161 ++++++++++++++++++++++++
>   1 file changed, 161 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index 4d75f9db08c2..c177283b6764 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -6,6 +6,8 @@
>   /dts-v1/;
>   
>   #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include <dt-bindings/sound/qcom,q6afe.h>
> +#include <dt-bindings/sound/qcom,q6asm.h>
>   #include "sm8450.dtsi"
>   
>   / {
> @@ -421,6 +423,147 @@ &uart7 {
>   	status = "okay";
>   };
>   
> +&soc {

soc should go before uart alphabetically.


Other than that:

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>


Konrad

> +	wcd938x: codec {
> +		compatible = "qcom,wcd9380-codec";
> +
> +		qcom,micbias1-microvolt = <1800000>;
> +		qcom,micbias2-microvolt = <1800000>;
> +		qcom,micbias3-microvolt = <1800000>;
> +		qcom,micbias4-microvolt = <1800000>;
> +		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
> +		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
> +		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
> +		qcom,rx-device = <&wcd_rx>;
> +		qcom,tx-device = <&wcd_tx>;
> +
> +		reset-gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
> +		#sound-dai-cells = <1>;
> +
> +		vdd-buck-supply = <&vreg_s10b_1p8>;
> +		vdd-rxtx-supply = <&vreg_s10b_1p8>;
> +		vdd-io-supply = <&vreg_s10b_1p8>;
> +		vdd-mic-bias-supply = <&vreg_bob>;
> +	};
> +};
> +
> +&sound {
> +	compatible = "qcom,sm8450-sndcard";
> +	model = "SM8450-HDK";
> +	audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
> +			"SpkrRight IN", "WSA_SPK2 OUT",
> +			"IN1_HPHL", "HPHL_OUT",
> +			"IN2_HPHR", "HPHR_OUT",
> +			"AMIC1", "MIC BIAS1",
> +			"AMIC2", "MIC BIAS2",
> +			"AMIC3", "MIC BIAS3",
> +			"AMIC4", "MIC BIAS3",
> +			"AMIC5", "MIC BIAS4";
> +
> +	wcd-playback-dai-link {
> +		link-name = "WCD Playback";
> +		cpu {
> +			sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
> +		};
> +
> +		codec {
> +			sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
> +		};
> +
> +		platform {
> +			sound-dai = <&q6apm>;
> +		};
> +	};
> +
> +	wcd-playback-dai-link {
> +		link-name = "WCD Playback";
> +		cpu {
> +			sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
> +		};
> +
> +		codec {
> +			sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
> +		};
> +
> +		platform {
> +			sound-dai = <&q6apm>;
> +		};
> +	};
> +
> +	wsa-dai-link {
> +		link-name = "WSA Playback";
> +		cpu {
> +			sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
> +		};
> +
> +		codec {
> +			sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>;
> +		};
> +
> +		platform {
> +			sound-dai = <&q6apm>;
> +		};
> +	};
> +
> +	va-dai-link {
> +		link-name = "VA Capture";
> +		cpu {
> +			sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
> +		};
> +
> +		platform {
> +			sound-dai = <&q6apm>;
> +		};
> +	};
> +};
> +
> +&swr0 {
> +	right_spkr: speaker@0,1{
> +		compatible = "sdw10217020200";
> +		reg = <0 1>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&spkr_1_sd_n_active>;
> +		powerdown-gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
> +		#sound-dai-cells = <0>;
> +		sound-name-prefix = "SpkrRight";
> +		#thermal-sensor-cells = <0>;
> +		vdd-supply = <&vreg_s10b_1p8>;
> +	};
> +
> +	left_spkr: speaker@0,2{
> +		compatible = "sdw10217020200";
> +		reg = <0 2>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&spkr_2_sd_n_active>;
> +		powerdown-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
> +		#sound-dai-cells = <0>;
> +		sound-name-prefix = "SpkrLeft";
> +		#thermal-sensor-cells = <0>;
> +		vdd-supply = <&vreg_s10b_1p8>;
> +	};
> +};
> +
> +&swr1 {
> +	status = "okay";
> +
> +	wcd_rx: codec@0,4 {
> +		compatible = "sdw20217010d00";
> +		reg = <0 4>;
> +		qcom,rx-port-mapping = <1 2 3 4 5>;
> +	};
> +};
> +
> +&swr2 {
> +	status = "okay";
> +
> +	wcd_tx: codec@0,3 {
> +		compatible = "sdw20217010d00";
> +		reg = <0 3>;
> +		/* ports: adc1_2, adc3_4, dmic0_3_mbhc, dmic4_7 */
> +		qcom,tx-port-mapping = <1 1 2 3>;
> +	};
> +};
> +
>   &ufs_mem_hc {
>   	status = "okay";
>   
> @@ -461,3 +604,21 @@ &usb_1_qmpphy {
>   	vdda-phy-supply = <&vreg_l6b_1p2>;
>   	vdda-pll-supply = <&vreg_l1b_0p91>;
>   };
> +
> +&tlmm {
> +	spkr_1_sd_n_active: spkr-1-sd-n-active-state {
> +		pins = "gpio1";
> +		function = "gpio";
> +		drive-strength = <4>;
> +		bias-disable;
> +		output-low;
> +	};
> +
> +	spkr_2_sd_n_active: spkr-2-sd-n-active-state {
> +		pins = "gpio89";
> +		function = "gpio";
> +		drive-strength = <4>;
> +		bias-disable;
> +		output-low;
> +	};
> +};

Re: [PATCH 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS

[Krzysztof Kozlowski]

On 14/11/2022 16:37, Konrad Dybcio wrote:
> 
> On 14/11/2022 16:21, Krzysztof Kozlowski wrote:
>> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>>
>> Add Soundwire controllers, Low Power Audio SubSystem (LPASS) devices and
>> LPASS pin controller.
>>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> ---
>>   arch/arm64/boot/dts/qcom/sm8450.dtsi | 295 +++++++++++++++++++++++++++
>>   1 file changed, 295 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
>> index 4b0a1eee8bd9..c99740591467 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
>> @@ -15,6 +15,7 @@
>>   #include <dt-bindings/interconnect/qcom,sm8450.h>
>>   #include <dt-bindings/soc/qcom,gpr.h>
>>   #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>> +#include <dt-bindings/sound/qcom,q6afe.h>
>>   #include <dt-bindings/thermal/thermal.h>
>>   
>>   / {
>> @@ -2097,6 +2098,212 @@ compute-cb@3 {
>>   			};
>>   		};
>>   
>> +		wsa2macro: codec@31e0000 {
>> +			compatible = "qcom,sm8450-lpass-wsa-macro";
>> +			reg = <0 0x031e0000 0 0x1000>;
> The sorting will be off, as adsp and cdsp have been mistakenly put in
> the wrong place (notice adsp @ 32300000 is actually at an address
> that's 8 hex digits long, but the reg addr is padded to 9 hex digits..).

I don't get it. This has address:
31e0000
ADSP has
30000000

so why sorting is odd?

> > Could you submit a fix for that as well?

For 9 digits, sure, but this is independent issue.

> 
>> +			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>> +				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>> +				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>> +				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>> +				 <&vamacro>;
>> +			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
>> +			assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>> +					  <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> 
> Remove the duplicated space before LPASS_CLK_ATTRIBUTE_COUPLE_NO.

Ack.


Best regards,
Krzysztof

Re: [PATCH 3/3] arm64: dts: qcom: sm8450-hdk: add sound support

[Krzysztof Kozlowski]

On 14/11/2022 16:39, Konrad Dybcio wrote:
> 
> On 14/11/2022 16:21, Krzysztof Kozlowski wrote:
>> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>>
>> Add sound support to SM8450 HDK board.  Tested setup so far is only two
>> speakers (working) and head-phones (only one channel working).
>>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> ---
>>   arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 161 ++++++++++++++++++++++++
>>   1 file changed, 161 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>> index 4d75f9db08c2..c177283b6764 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>> @@ -6,6 +6,8 @@
>>   /dts-v1/;
>>   
>>   #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
>> +#include <dt-bindings/sound/qcom,q6afe.h>
>> +#include <dt-bindings/sound/qcom,q6asm.h>
>>   #include "sm8450.dtsi"
>>   
>>   / {
>> @@ -421,6 +423,147 @@ &uart7 {
>>   	status = "okay";
>>   };
>>   
>> +&soc {
> 
> soc should go before uart alphabetically.
> 
> 
> Other than that:
> 
> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> 
> 

Ack

Best regards,
Krzysztof

Re: [PATCH 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS

[Konrad Dybcio]

On 15/11/2022 11:15, Krzysztof Kozlowski wrote:
> On 14/11/2022 16:37, Konrad Dybcio wrote:
>>
>> On 14/11/2022 16:21, Krzysztof Kozlowski wrote:
>>> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>>>
>>> Add Soundwire controllers, Low Power Audio SubSystem (LPASS) devices and
>>> LPASS pin controller.
>>>
>>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>>> Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>>> ---
>>>    arch/arm64/boot/dts/qcom/sm8450.dtsi | 295 +++++++++++++++++++++++++++
>>>    1 file changed, 295 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
>>> index 4b0a1eee8bd9..c99740591467 100644
>>> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
>>> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
>>> @@ -15,6 +15,7 @@
>>>    #include <dt-bindings/interconnect/qcom,sm8450.h>
>>>    #include <dt-bindings/soc/qcom,gpr.h>
>>>    #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>>> +#include <dt-bindings/sound/qcom,q6afe.h>
>>>    #include <dt-bindings/thermal/thermal.h>
>>>    
>>>    / {
>>> @@ -2097,6 +2098,212 @@ compute-cb@3 {
>>>    			};
>>>    		};
>>>    
>>> +		wsa2macro: codec@31e0000 {
>>> +			compatible = "qcom,sm8450-lpass-wsa-macro";
>>> +			reg = <0 0x031e0000 0 0x1000>;
>> The sorting will be off, as adsp and cdsp have been mistakenly put in
>> the wrong place (notice adsp @ 32300000 is actually at an address
>> that's 8 hex digits long, but the reg addr is padded to 9 hex digits..).
> 
> I don't get it. This has address:
> 31e0000
> ADSP has
> 30000000
> 
> so why sorting is odd?
It's gonna be fine, you're right, I can't read properly...

Konrad
> 
>>> Could you submit a fix for that as well?
> 
> For 9 digits, sure, but this is independent issue.
> 
>>
>>> +			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>>> +				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>>> +				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>>> +				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>>> +				 <&vamacro>;
>>> +			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
>>> +			assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
>>> +					  <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
>>
>> Remove the duplicated space before LPASS_CLK_ATTRIBUTE_COUPLE_NO.
> 
> Ack.
> 
> 
> Best regards,
> Krzysztof
>