* Multiple errors with DVD drive
@ 2022-05-26 12:38 J.J. Berkhout
2022-05-26 23:36 ` Damien Le Moal
2022-09-20 13:35 ` Niklas Cassel
0 siblings, 2 replies; 20+ messages in thread
From: J.J. Berkhout @ 2022-05-26 12:38 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 1745 bytes --]
Firstly, if this is not the right place for this message, I apologize.
In this case, disregard.
I have a problem which I suspect is a bug in libata, but of course I
could be wrong.
The problem is:
After going from Linux Mint 19.3 Cinnamon kernel 5.4.0-97 to Linux Mint
20.3 Cinnamon kernel 5.4.0-107 I discovered that I could not (reliably)
access my optical drive anymore.
It produces errors like:
ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
ata1.00: cmd a0/00:00:00:00:fc/00:00:00:00:00/a0 tag 0 pio 131072 in
Read(10) 28 00 00 00 05 61 00 00 40 00res
50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
blk_update_request: I/O error, dev sr0, sector 5508 op 0x0:(READ) flags
0x80700 phys_seg 19 prio class 0
ata1.00: failed to set xfermode (err_mask=0x1)
The system was Linux Mint 20.3 Cinnamon with kernel 5.4.0-107-generic,
mobo ASRock model X570 Taichi.
After some tests I found out:
Kernel 5.4.0-99 works OK;
Kernel 5.4.0-100 has the problem;
Kernel 5.13.0-30 works OK;
Kernel 5.13.0-35 has the problem.
The problem is described more fully in
https://forums.linuxmint.com/viewtopic.php?f=47&t=371251
I reported the bug to the Launchpad Ubuntu site under number #1968155:
https://bugs.launchpad.net/bugs/1968155
One other person (as far as I know) has the same problem.
I froze my kernel at 5.13.0-30, so for the moment I can use my system.
I realize that there are probably not many users with an ASRock X570
mobo, and in that group only a few would be using a BD reader/burner.
However, it would be nice if I could again keep my kernel current.
With kind regards,
Jaap Berkhout
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-05-26 12:38 Multiple errors with DVD drive J.J. Berkhout
@ 2022-05-26 23:36 ` Damien Le Moal
2022-05-27 8:50 ` J.J. Berkhout
2022-05-27 10:32 ` J.J. Berkhout
2022-09-20 13:35 ` Niklas Cassel
1 sibling, 2 replies; 20+ messages in thread
From: Damien Le Moal @ 2022-05-26 23:36 UTC (permalink / raw)
To: J.J. Berkhout, linux-ide
On 2022/05/26 21:38, J.J. Berkhout wrote:
> Firstly, if this is not the right place for this message, I apologize.
> In this case, disregard.
>
> I have a problem which I suspect is a bug in libata, but of course I
> could be wrong.
>
> The problem is:
> After going from Linux Mint 19.3 Cinnamon kernel 5.4.0-97 to Linux Mint
> 20.3 Cinnamon kernel 5.4.0-107 I discovered that I could not (reliably)
> access my optical drive anymore.
> It produces errors like:
> ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
> ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
> ata1.00: cmd a0/00:00:00:00:fc/00:00:00:00:00/a0 tag 0 pio 131072 in
> Read(10) 28 00 00 00 05 61 00 00 40 00res
> 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
> blk_update_request: I/O error, dev sr0, sector 5508 op 0x0:(READ) flags
> 0x80700 phys_seg 19 prio class 0
> ata1.00: failed to set xfermode (err_mask=0x1)
>
> The system was Linux Mint 20.3 Cinnamon with kernel 5.4.0-107-generic,
> mobo ASRock model X570 Taichi.
> After some tests I found out:
> Kernel 5.4.0-99 works OK;
> Kernel 5.4.0-100 has the problem;
> Kernel 5.13.0-30 works OK;
> Kernel 5.13.0-35 has the problem.
It looks like your distro is backporting patches so the patch causing the
problem could be found by bisecting. While 5.4 kernel is an LTS kernel, the
latest release is 5.4.196... 5.4.0-100 is the distro version number which does
not tell me what set of patches it got on top of 5.4.0. These are not
stable/vanilla kernels.
To get help from this list, you will need to try with a vanilla kernel, ideally
from git. You could try the latest mainline 5.18 first to see if the problem is
there or not.
Also, what AHCI adapter is this machine using (lspci) ?
>
> The problem is described more fully in
> https://forums.linuxmint.com/viewtopic.php?f=47&t=371251
>
> I reported the bug to the Launchpad Ubuntu site under number #1968155:
> https://bugs.launchpad.net/bugs/1968155
>
> One other person (as far as I know) has the same problem.
>
> I froze my kernel at 5.13.0-30, so for the moment I can use my system.
> I realize that there are probably not many users with an ASRock X570
> mobo, and in that group only a few would be using a BD reader/burner.
> However, it would be nice if I could again keep my kernel current.
>
> With kind regards,
>
> Jaap Berkhout
--
Damien Le Moal
Western Digital Research
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-05-26 23:36 ` Damien Le Moal
@ 2022-05-27 8:50 ` J.J. Berkhout
2022-05-27 10:32 ` J.J. Berkhout
1 sibling, 0 replies; 20+ messages in thread
From: J.J. Berkhout @ 2022-05-27 8:50 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 2084 bytes --]
On 27-05-2022 01:36, Damien Le Moal wrote:
> On 2022/05/26 21:38, J.J. Berkhout wrote:
>> The problem is:
>> After going from Linux Mint 19.3 Cinnamon kernel 5.4.0-97 to Linux Mint
>> 20.3 Cinnamon kernel 5.4.0-107 I discovered that I could not (reliably)
>> access my optical drive anymore.
>> It produces errors like:
>> ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
>> ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
>> ata1.00: cmd a0/00:00:00:00:fc/00:00:00:00:00/a0 tag 0 pio 131072 in
>> Read(10) 28 00 00 00 05 61 00 00 40 00res
>> 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
>> blk_update_request: I/O error, dev sr0, sector 5508 op 0x0:(READ) flags
>> 0x80700 phys_seg 19 prio class 0
>> ata1.00: failed to set xfermode (err_mask=0x1)
>>
>> The system was Linux Mint 20.3 Cinnamon with kernel 5.4.0-107-generic,
>> mobo ASRock model X570 Taichi.
>> After some tests I found out:
>> Kernel 5.4.0-99 works OK;
>> Kernel 5.4.0-100 has the problem;
>> Kernel 5.13.0-30 works OK;
>> Kernel 5.13.0-35 has the problem.
>
> It looks like your distro is backporting patches so the patch causing the
> problem could be found by bisecting. While 5.4 kernel is an LTS kernel, the
> latest release is 5.4.196... 5.4.0-100 is the distro version number which does
> not tell me what set of patches it got on top of 5.4.0. These are not
> stable/vanilla kernels.
>
> To get help from this list, you will need to try with a vanilla kernel, ideally
> from git. You could try the latest mainline 5.18 first to see if the problem is
> there or not.
OK, will start working on it. I never before tried a kernel not from
the repository, so I have to find out how to manage it.
>> Also, what AHCI adapter is this machine using (lspci) ?
Output from sudo lspci | grep -i ahci:
0b:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA
Controller [AHCI mode] (rev 51)
0c:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA
Controller [AHCI mode] (rev 51)
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-05-26 23:36 ` Damien Le Moal
2022-05-27 8:50 ` J.J. Berkhout
@ 2022-05-27 10:32 ` J.J. Berkhout
2022-08-05 9:17 ` J.J. Berkhout
1 sibling, 1 reply; 20+ messages in thread
From: J.J. Berkhout @ 2022-05-27 10:32 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1.1.1: Type: text/plain, Size: 1933 bytes --]
Hello,
On 27-05-2022 01:36, Damien Le Moal wrote:
> On 2022/05/26 21:38, J.J. Berkhout wrote:
.
.
>> The problem is:
>> After going from Linux Mint 19.3 Cinnamon kernel 5.4.0-97 to Linux Mint
>> 20.3 Cinnamon kernel 5.4.0-107 I discovered that I could not (reliably)
>> access my optical drive anymore.
>> It produces errors like:
>> ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
>> ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
>> ata1.00: cmd a0/00:00:00:00:fc/00:00:00:00:00/a0 tag 0 pio 131072 in
>> Read(10) 28 00 00 00 05 61 00 00 40 00res
>> 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
>> blk_update_request: I/O error, dev sr0, sector 5508 op 0x0:(READ) flags
>> 0x80700 phys_seg 19 prio class 0
>> ata1.00: failed to set xfermode (err_mask=0x1)
>>
>> The system was Linux Mint 20.3 Cinnamon with kernel 5.4.0-107-generic,
>> mobo ASRock model X570 Taichi.
>> After some tests I found out:
>> Kernel 5.4.0-99 works OK;
>> Kernel 5.4.0-100 has the problem;
>> Kernel 5.13.0-30 works OK;
>> Kernel 5.13.0-35 has the problem.
>
> It looks like your distro is backporting patches so the patch causing the
> problem could be found by bisecting. While 5.4 kernel is an LTS kernel, the
> latest release is 5.4.196... 5.4.0-100 is the distro version number which does
> not tell me what set of patches it got on top of 5.4.0. These are not
> stable/vanilla kernels.
>
> To get help from this list, you will need to try with a vanilla kernel, ideally
> from git. You could try the latest mainline 5.18 first to see if the problem is
> there or not.
OK, I installed kernel 5.18.0 with 'mainline' (Ubuntu Mainline Kernel
Installer).
Kernel installed was 5.18.0-051800.202205222030.
Same problem existed.
I reverted to the ubuntu 5.13.0-30 kernel.
A copy of the dmesg output is attached.
With kind regards,
Jaap Berkhout.
[-- Attachment #1.1.2: ataerr.log --]
[-- Type: text/x-log, Size: 112050 bytes --]
[ 0.000000] Linux version 5.18.0-051800-generic (kernel@kathleen) (gcc (Ubuntu 11.3.0-3ubuntu1) 11.3.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #202205222030 SMP PREEMPT_DYNAMIC Sun May 22 20:33:46 UTC 2022
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-5.18.0-051800-generic root=UUID=9d60bcb5-650d-484d-ae74-728526cd6db1 ro ipv6.disable=1 elevator=deadline quiet splash nomodeset
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Hygon HygonGenuine
[ 0.000000] Centaur CentaurHauls
[ 0.000000] zhaoxin Shanghai
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'compacted' format.
[ 0.000000] signal: max sigframe size: 1776
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000000a0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000009afefff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000009aff000-0x0000000009ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000a000000-0x000000000a1fffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000a200000-0x000000000a20ffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000000a210000-0x00000000cb61afff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cb61b000-0x00000000ccc15fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ccc16000-0x00000000ccc4afff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000ccc4b000-0x00000000cd2c3fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000cd2c4000-0x00000000cdffefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000cdfff000-0x00000000ceffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cf000000-0x00000000cfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fd200000-0x00000000fd2fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fd400000-0x00000000fd5fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fea00000-0x00000000fea0ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb80000-0x00000000fec01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fedc2000-0x00000000fedcffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fedd4000-0x00000000fedd5fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000042f37ffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000042f380000-0x000000042fffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] e820: update [mem 0xc5987018-0xc5995857] usable ==> usable
[ 0.000000] e820: update [mem 0xc5987018-0xc5995857] usable ==> usable
[ 0.000000] e820: update [mem 0xc5966018-0xc5986057] usable ==> usable
[ 0.000000] e820: update [mem 0xc5966018-0xc5986057] usable ==> usable
[ 0.000000] extended physical RAM map:
[ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000009ffff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000000a0000-0x00000000000fffff] reserved
[ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x0000000009afefff] usable
[ 0.000000] reserve setup_data: [mem 0x0000000009aff000-0x0000000009ffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x000000000a000000-0x000000000a1fffff] usable
[ 0.000000] reserve setup_data: [mem 0x000000000a200000-0x000000000a20ffff] ACPI NVS
[ 0.000000] reserve setup_data: [mem 0x000000000a210000-0x00000000c5966017] usable
[ 0.000000] reserve setup_data: [mem 0x00000000c5966018-0x00000000c5986057] usable
[ 0.000000] reserve setup_data: [mem 0x00000000c5986058-0x00000000c5987017] usable
[ 0.000000] reserve setup_data: [mem 0x00000000c5987018-0x00000000c5995857] usable
[ 0.000000] reserve setup_data: [mem 0x00000000c5995858-0x00000000cb61afff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000cb61b000-0x00000000ccc15fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000ccc16000-0x00000000ccc4afff] ACPI data
[ 0.000000] reserve setup_data: [mem 0x00000000ccc4b000-0x00000000cd2c3fff] ACPI NVS
[ 0.000000] reserve setup_data: [mem 0x00000000cd2c4000-0x00000000cdffefff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000cdfff000-0x00000000ceffffff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000cf000000-0x00000000cfffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fd200000-0x00000000fd2fffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fd400000-0x00000000fd5fffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fea00000-0x00000000fea0ffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000feb80000-0x00000000fec01fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fedc2000-0x00000000fedcffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fedd4000-0x00000000fedd5fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000042f37ffff] usable
[ 0.000000] reserve setup_data: [mem 0x000000042f380000-0x000000042fffffff] reserved
[ 0.000000] efi: EFI v2.70 by American Megatrends
[ 0.000000] efi: ACPI=0xcd2ab000 ACPI 2.0=0xcd2ab014 SMBIOS=0xcde26000 SMBIOS 3.0=0xcde25000 MEMATTR=0xc9b46018 ESRT=0xc78d6098 MOKvar=0xc5a6b000 RNG=0xcde66318
[ 0.000000] efi: seeding entropy pool
[ 0.000000] random: crng init done
[ 0.000000] SMBIOS 3.2.0 present.
[ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./X570 Taichi, BIOS P3.80 12/01/2020
[ 0.000000] tsc: Fast TSC calibration failed
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] last_pfn = 0x42f380 max_arch_pfn = 0x400000000
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.000000] total RAM covered: 3327M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 64M num_reg: 4 lose cover RAM: 0G
[ 0.000000] e820: update [mem 0xcd5f0000-0xcd5fffff] usable ==> reserved
[ 0.000000] e820: update [mem 0xd0000000-0xffffffff] usable ==> reserved
[ 0.000000] last_pfn = 0xcf000 max_arch_pfn = 0x400000000
[ 0.000000] esrt: Reserving ESRT space from 0x00000000c78d6098 to 0x00000000c78d60d0.
[ 0.000000] e820: update [mem 0xc78d6000-0xc78d6fff] usable ==> reserved
[ 0.000000] e820: update [mem 0xc5a6b000-0xc5a6bfff] usable ==> reserved
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] Secure boot disabled
[ 0.000000] RAMDISK: [mem 0x34d7e000-0x3c9c9fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000CD2AB014 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x00000000CD2AA728 0000BC (v01 ALASKA A M I 01072009 AMI 01000013)
[ 0.000000] ACPI: FACP 0x00000000CCC3C000 000114 (v06 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 0x00000000CCC35000 006854 (v02 ALASKA A M I 01072009 INTL 20120913)
[ 0.000000] ACPI: FACS 0x00000000CD2A5000 000040
[ 0.000000] ACPI: SSDT 0x00000000CCC42000 008C98 (v02 AMD AmdTable 00000002 MSFT 04000000)
[ 0.000000] ACPI: SSDT 0x00000000CCC3E000 003A82 (v01 AMD AMD AOD 00000001 INTL 20120913)
[ 0.000000] ACPI: SSDT 0x00000000CCC3D000 0000C8 (v02 ALASKA CPUSSDT 01072009 AMI 01072009)
[ 0.000000] ACPI: FIDT 0x00000000CCC34000 00009C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x00000000CCC33000 00003C (v01 ALASKA A M I 01072009 MSFT 00010013)
[ 0.000000] ACPI: AAFT 0x00000000CCC32000 0000ED (v01 ALASKA OEMAAFT 01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000CCC31000 000038 (v01 ALASKA A M I 01072009 AMI 00000005)
[ 0.000000] ACPI: SSDT 0x00000000CCC30000 000024 (v01 AMD BIXBY 00001000 INTL 20120913)
[ 0.000000] ACPI: BGRT 0x00000000CCC2F000 000038 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: PCCT 0x00000000CCC2E000 00006E (v02 AMD AmdTable 00000001 AMD 00000000)
[ 0.000000] ACPI: SSDT 0x00000000CCC2B000 002F29 (v02 AMD AmdTable 00000001 AMD 00000001)
[ 0.000000] ACPI: CRAT 0x00000000CCC2A000 000B58 (v01 AMD AmdTable 00000001 AMD 00000001)
[ 0.000000] ACPI: CDIT 0x00000000CCC29000 000029 (v01 AMD AmdTable 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x00000000CCC25000 00348C (v01 AMD QOGIRN 00000001 INTL 20120913)
[ 0.000000] ACPI: WSMT 0x00000000CCC24000 000028 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: APIC 0x00000000CCC23000 00015E (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: SSDT 0x00000000CCC21000 0010AF (v01 AMD QOGIRC 00000001 INTL 20120913)
[ 0.000000] ACPI: FPDT 0x00000000CCC20000 000044 (v01 ALASKA A M I 01072009 AMI 01000013)
[ 0.000000] ACPI: Reserving FACP table memory at [mem 0xccc3c000-0xccc3c113]
[ 0.000000] ACPI: Reserving DSDT table memory at [mem 0xccc35000-0xccc3b853]
[ 0.000000] ACPI: Reserving FACS table memory at [mem 0xcd2a5000-0xcd2a503f]
[ 0.000000] ACPI: Reserving SSDT table memory at [mem 0xccc42000-0xccc4ac97]
[ 0.000000] ACPI: Reserving SSDT table memory at [mem 0xccc3e000-0xccc41a81]
[ 0.000000] ACPI: Reserving SSDT table memory at [mem 0xccc3d000-0xccc3d0c7]
[ 0.000000] ACPI: Reserving FIDT table memory at [mem 0xccc34000-0xccc3409b]
[ 0.000000] ACPI: Reserving MCFG table memory at [mem 0xccc33000-0xccc3303b]
[ 0.000000] ACPI: Reserving AAFT table memory at [mem 0xccc32000-0xccc320ec]
[ 0.000000] ACPI: Reserving HPET table memory at [mem 0xccc31000-0xccc31037]
[ 0.000000] ACPI: Reserving SSDT table memory at [mem 0xccc30000-0xccc30023]
[ 0.000000] ACPI: Reserving BGRT table memory at [mem 0xccc2f000-0xccc2f037]
[ 0.000000] ACPI: Reserving PCCT table memory at [mem 0xccc2e000-0xccc2e06d]
[ 0.000000] ACPI: Reserving SSDT table memory at [mem 0xccc2b000-0xccc2df28]
[ 0.000000] ACPI: Reserving CRAT table memory at [mem 0xccc2a000-0xccc2ab57]
[ 0.000000] ACPI: Reserving CDIT table memory at [mem 0xccc29000-0xccc29028]
[ 0.000000] ACPI: Reserving SSDT table memory at [mem 0xccc25000-0xccc2848b]
[ 0.000000] ACPI: Reserving WSMT table memory at [mem 0xccc24000-0xccc24027]
[ 0.000000] ACPI: Reserving APIC table memory at [mem 0xccc23000-0xccc2315d]
[ 0.000000] ACPI: Reserving SSDT table memory at [mem 0xccc21000-0xccc220ae]
[ 0.000000] ACPI: Reserving FPDT table memory at [mem 0xccc20000-0xccc20043]
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000042f37ffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x42f355000-0x42f37ffff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000042f37ffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009ffff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x0000000009afefff]
[ 0.000000] node 0: [mem 0x000000000a000000-0x000000000a1fffff]
[ 0.000000] node 0: [mem 0x000000000a210000-0x00000000cb61afff]
[ 0.000000] node 0: [mem 0x00000000cdfff000-0x00000000ceffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000042f37ffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000042f37ffff]
[ 0.000000] On node 0, zone DMA: 1 pages in unavailable ranges
[ 0.000000] On node 0, zone DMA: 96 pages in unavailable ranges
[ 0.000000] On node 0, zone DMA32: 1281 pages in unavailable ranges
[ 0.000000] On node 0, zone DMA32: 16 pages in unavailable ranges
[ 0.000000] On node 0, zone DMA32: 10724 pages in unavailable ranges
[ 0.000000] On node 0, zone Normal: 4096 pages in unavailable ranges
[ 0.000000] On node 0, zone Normal: 3200 pages in unavailable ranges
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 13, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] IOAPIC[1]: apic_id 14, version 33, address 0xfec01000, GSI 24-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10228201 base: 0xfed00000
[ 0.000000] e820: update [mem 0xc781d000-0xc785dfff] usable ==> reserved
[ 0.000000] smpboot: Allowing 32 CPUs, 20 hotplug CPUs
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0x09aff000-0x09ffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0x0a200000-0x0a20ffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xc5966000-0xc5966fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xc5986000-0xc5986fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xc5987000-0xc5987fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xc5995000-0xc5995fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xc5a6b000-0xc5a6bfff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xc781d000-0xc785dfff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xc78d6000-0xc78d6fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xcb61b000-0xccc15fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xccc16000-0xccc4afff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xccc4b000-0xcd2c3fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xcd2c4000-0xcdffefff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xcf000000-0xcfffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xd0000000-0xefffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xf0000000-0xf7ffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xf8000000-0xfd1fffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfd200000-0xfd2fffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfd300000-0xfd3fffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfd400000-0xfd5fffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfd600000-0xfe9fffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfea00000-0xfea0ffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfea10000-0xfeb7ffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfeb80000-0xfec01fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfec11000-0xfecfffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfed90000-0xfedc1fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfedc2000-0xfedcffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfedd0000-0xfedd3fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfedd4000-0xfedd5fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfedd6000-0xfeffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] [mem 0xd0000000-0xefffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:32 nr_cpu_ids:32 nr_node_ids:1
[ 0.000000] percpu: Embedded 61 pages/cpu s212992 r8192 d28672 u262144
[ 0.000000] pcpu-alloc: s212992 r8192 d28672 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 [0] 08 09 10 11 12 13 14 15
[ 0.000000] pcpu-alloc: [0] 16 17 18 19 20 21 22 23 [0] 24 25 26 27 28 29 30 31
[ 0.000000] Fallback order for Node 0: 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 4109496
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-5.18.0-051800-generic root=UUID=9d60bcb5-650d-484d-ae74-728526cd6db1 ro ipv6.disable=1 elevator=deadline quiet splash nomodeset
[ 0.000000] Kernel parameter elevator= does not have any effect anymore.
Please use sysfs to set IO scheduler for individual devices.
[ 0.000000] Booted with the nomodeset parameter. Only the system framebuffer will be available
[ 0.000000] Unknown kernel command line parameters "splash BOOT_IMAGE=/vmlinuz-5.18.0-051800-generic", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000] Memory: 16057472K/16699560K available (16392K kernel code, 4567K rwdata, 10976K rodata, 2764K init, 4800K bss, 641828K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=32, Nodes=1
[ 0.000000] ftrace: allocating 51202 entries in 201 pages
[ 0.000000] ftrace: allocated 201 pages with 4 groups
[ 0.000000] Dynamic Preempt: voluntary
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=32.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=32
[ 0.000000] NR_IRQS: 524544, nr_irqs: 1224, preallocated irqs: 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] printk: console [tty0] enabled
[ 0.000000] ACPI: Core revision 20211217
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.000000] APIC: Switch to symmetric I/O mode setup
[ 0.000000] Switched APIC routing to physical flat.
[ 0.000000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.028000] tsc: PIT calibration matches HPET. 2 loops
[ 0.028000] tsc: Detected 3799.842 MHz processor
[ 0.000002] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x6d8b860a2c5, max_idle_ns: 881590565945 ns
[ 0.000005] Calibrating delay loop (skipped), value calculated using timer frequency.. 7599.68 BogoMIPS (lpj=15199368)
[ 0.000006] pid_max: default: 32768 minimum: 301
[ 0.002900] LSM: Security Framework initializing
[ 0.002909] landlock: Up and running.
[ 0.002909] Yama: becoming mindful.
[ 0.002923] AppArmor: AppArmor initialized
[ 0.002959] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.002979] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.003128] x86/cpu: User Mode Instruction Prevention (UMIP) activated
[ 0.003179] LVT offset 1 assigned for vector 0xf9
[ 0.003305] LVT offset 2 assigned for vector 0xf4
[ 0.003340] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 512
[ 0.003340] Last level dTLB entries: 4KB 2048, 2MB 2048, 4MB 1024, 1GB 0
[ 0.003343] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[ 0.003344] Spectre V2 : Mitigation: Retpolines
[ 0.003344] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.003345] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[ 0.003346] Spectre V2 : User space: Mitigation: STIBP via prctl
[ 0.003347] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl
[ 0.005014] Freeing SMP alternatives memory: 40K
[ 0.113561] smpboot: CPU0: AMD Ryzen 5 3600X 6-Core Processor (family: 0x17, model: 0x71, stepping: 0x0)
[ 0.113627] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.113630] cblist_init_generic: Setting shift to 5 and lim to 1.
[ 0.113641] cblist_init_generic: Setting shift to 5 and lim to 1.
[ 0.113650] cblist_init_generic: Setting shift to 5 and lim to 1.
[ 0.113657] Performance Events: Fam17h+ core perfctr, AMD PMU driver.
[ 0.113660] ... version: 0
[ 0.113661] ... bit width: 48
[ 0.113661] ... generic registers: 6
[ 0.113662] ... value mask: 0000ffffffffffff
[ 0.113662] ... max period: 00007fffffffffff
[ 0.113663] ... fixed-purpose events: 0
[ 0.113663] ... event mask: 000000000000003f
[ 0.113699] rcu: Hierarchical SRCU implementation.
[ 0.113992] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.114127] smp: Bringing up secondary CPUs ...
[ 0.114182] x86: Booting SMP configuration:
[ 0.114182] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11
[ 0.136437] smp: Brought up 1 node, 12 CPUs
[ 0.136439] smpboot: Max logical packages: 3
[ 0.136439] smpboot: Total of 12 processors activated (91196.20 BogoMIPS)
[ 0.137222] devtmpfs: initialized
[ 0.137222] x86/mm: Memory block size: 128MB
[ 0.140494] ACPI: PM: Registering ACPI NVS region [mem 0x0a200000-0x0a20ffff] (65536 bytes)
[ 0.140494] ACPI: PM: Registering ACPI NVS region [mem 0xccc4b000-0xcd2c3fff] (6787072 bytes)
[ 0.140494] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.140494] futex hash table entries: 8192 (order: 7, 524288 bytes, linear)
[ 0.140494] pinctrl core: initialized pinctrl subsystem
[ 0.140494] PM: RTC time: 09:54:17, date: 2022-05-27
[ 0.140497] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.140646] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[ 0.140736] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.140829] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.140833] audit: initializing netlink subsys (disabled)
[ 0.140837] audit: type=2000 audit(1653645257.168:1): state=initialized audit_enabled=0 res=1
[ 0.140837] thermal_sys: Registered thermal governor 'fair_share'
[ 0.140837] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.140837] thermal_sys: Registered thermal governor 'step_wise'
[ 0.140837] thermal_sys: Registered thermal governor 'user_space'
[ 0.140837] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.140837] EISA bus registered
[ 0.140837] cpuidle: using governor ladder
[ 0.140837] cpuidle: using governor menu
[ 0.140837] Detected 1 PCC Subspaces
[ 0.140837] Registering PCC driver as Mailbox controller
[ 0.140837] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.140837] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[ 0.140837] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820
[ 0.140837] PCI: Using configuration type 1 for base access
[ 0.141046] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[ 0.141051] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.141051] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.141051] ACPI: Added _OSI(Module Device)
[ 0.141051] ACPI: Added _OSI(Processor Device)
[ 0.141051] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.141051] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.141051] ACPI: Added _OSI(Linux-Dell-Video)
[ 0.141051] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[ 0.141051] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[ 0.153624] ACPI: 8 ACPI AML tables successfully acquired and loaded
[ 0.154869] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 0.157594] ACPI: Interpreter enabled
[ 0.157605] ACPI: PM: (supports S0 S3 S4 S5)
[ 0.157606] ACPI: Using IOAPIC for interrupt routing
[ 0.157868] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.158187] ACPI: Enabled 2 GPEs in block 00 to 1F
[ 0.166042] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.166047] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[ 0.166168] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug PME AER PCIeCapability LTR]
[ 0.166175] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-7f] only partially covers this bridge
[ 0.166458] PCI host bridge to bus 0000:00
[ 0.166460] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 0.166461] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 0.166462] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 0.166462] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.166463] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000dffff window]
[ 0.166464] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfec02fff window]
[ 0.166465] pci_bus 0000:00: root bus resource [mem 0xfee00000-0xffffffff window]
[ 0.166466] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.166475] pci 0000:00:00.0: [1022:1480] type 00 class 0x060000
[ 0.166548] pci 0000:00:01.0: [1022:1482] type 00 class 0x060000
[ 0.166594] pci 0000:00:01.2: [1022:1483] type 01 class 0x060400
[ 0.166619] pci 0000:00:01.2: enabling Extended Tags
[ 0.166665] pci 0000:00:01.2: PME# supported from D0 D3hot D3cold
[ 0.166752] pci 0000:00:02.0: [1022:1482] type 00 class 0x060000
[ 0.166800] pci 0000:00:03.0: [1022:1482] type 00 class 0x060000
[ 0.166845] pci 0000:00:03.1: [1022:1483] type 01 class 0x060400
[ 0.166924] pci 0000:00:03.1: PME# supported from D0 D3hot D3cold
[ 0.167011] pci 0000:00:04.0: [1022:1482] type 00 class 0x060000
[ 0.167060] pci 0000:00:05.0: [1022:1482] type 00 class 0x060000
[ 0.167108] pci 0000:00:07.0: [1022:1482] type 00 class 0x060000
[ 0.167152] pci 0000:00:07.1: [1022:1484] type 01 class 0x060400
[ 0.167175] pci 0000:00:07.1: enabling Extended Tags
[ 0.167213] pci 0000:00:07.1: PME# supported from D0 D3hot D3cold
[ 0.167284] pci 0000:00:08.0: [1022:1482] type 00 class 0x060000
[ 0.167329] pci 0000:00:08.1: [1022:1484] type 01 class 0x060400
[ 0.167354] pci 0000:00:08.1: enabling Extended Tags
[ 0.167394] pci 0000:00:08.1: PME# supported from D0 D3hot D3cold
[ 0.167486] pci 0000:00:14.0: [1022:790b] type 00 class 0x0c0500
[ 0.167582] pci 0000:00:14.3: [1022:790e] type 00 class 0x060100
[ 0.167682] pci 0000:00:18.0: [1022:1440] type 00 class 0x060000
[ 0.167703] pci 0000:00:18.1: [1022:1441] type 00 class 0x060000
[ 0.167724] pci 0000:00:18.2: [1022:1442] type 00 class 0x060000
[ 0.167745] pci 0000:00:18.3: [1022:1443] type 00 class 0x060000
[ 0.167766] pci 0000:00:18.4: [1022:1444] type 00 class 0x060000
[ 0.167789] pci 0000:00:18.5: [1022:1445] type 00 class 0x060000
[ 0.167809] pci 0000:00:18.6: [1022:1446] type 00 class 0x060000
[ 0.167830] pci 0000:00:18.7: [1022:1447] type 00 class 0x060000
[ 0.167902] pci 0000:01:00.0: [1022:57ad] type 01 class 0x060400
[ 0.167957] pci 0000:01:00.0: enabling Extended Tags
[ 0.168043] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.168141] pci 0000:01:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 126.024 Gb/s with 16.0 GT/s PCIe x8 link)
[ 0.168183] pci 0000:00:01.2: PCI bridge to [bus 01-0c]
[ 0.168187] pci 0000:00:01.2: bridge window [io 0xd000-0xefff]
[ 0.168189] pci 0000:00:01.2: bridge window [mem 0xfc200000-0xfc8fffff]
[ 0.168432] pci 0000:02:03.0: [1022:57a3] type 01 class 0x060400
[ 0.168502] pci 0000:02:03.0: enabling Extended Tags
[ 0.168750] pci 0000:02:03.0: PME# supported from D0 D3hot D3cold
[ 0.169168] pci 0000:02:05.0: [1022:57a3] type 01 class 0x060400
[ 0.169237] pci 0000:02:05.0: enabling Extended Tags
[ 0.169485] pci 0000:02:05.0: PME# supported from D0 D3hot D3cold
[ 0.169912] pci 0000:02:08.0: [1022:57a4] type 01 class 0x060400
[ 0.169982] pci 0000:02:08.0: enabling Extended Tags
[ 0.170139] pci 0000:02:08.0: PME# supported from D0 D3hot D3cold
[ 0.170312] pci 0000:02:09.0: [1022:57a4] type 01 class 0x060400
[ 0.170381] pci 0000:02:09.0: enabling Extended Tags
[ 0.170539] pci 0000:02:09.0: PME# supported from D0 D3hot D3cold
[ 0.170704] pci 0000:02:0a.0: [1022:57a4] type 01 class 0x060400
[ 0.170773] pci 0000:02:0a.0: enabling Extended Tags
[ 0.170951] pci 0000:02:0a.0: PME# supported from D0 D3hot D3cold
[ 0.171124] pci 0000:01:00.0: PCI bridge to [bus 02-0c]
[ 0.171130] pci 0000:01:00.0: bridge window [io 0xd000-0xefff]
[ 0.171134] pci 0000:01:00.0: bridge window [mem 0xfc200000-0xfc8fffff]
[ 0.171238] pci 0000:03:00.0: [1b21:1184] type 01 class 0x060400
[ 0.171314] pci 0000:03:00.0: enabling Extended Tags
[ 0.171407] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.171548] pci 0000:02:03.0: PCI bridge to [bus 03-08]
[ 0.171554] pci 0000:02:03.0: bridge window [io 0xe000-0xefff]
[ 0.171558] pci 0000:02:03.0: bridge window [mem 0xfc400000-0xfc5fffff]
[ 0.171631] pci 0000:04:01.0: [1b21:1184] type 01 class 0x060400
[ 0.171710] pci 0000:04:01.0: enabling Extended Tags
[ 0.171799] pci 0000:04:01.0: PME# supported from D0 D3hot D3cold
[ 0.171900] pci 0000:04:03.0: [1b21:1184] type 01 class 0x060400
[ 0.171979] pci 0000:04:03.0: enabling Extended Tags
[ 0.172070] pci 0000:04:03.0: PME# supported from D0 D3hot D3cold
[ 0.172171] pci 0000:04:05.0: [1b21:1184] type 01 class 0x060400
[ 0.172250] pci 0000:04:05.0: enabling Extended Tags
[ 0.172339] pci 0000:04:05.0: PME# supported from D0 D3hot D3cold
[ 0.172443] pci 0000:04:07.0: [1b21:1184] type 01 class 0x060400
[ 0.172522] pci 0000:04:07.0: enabling Extended Tags
[ 0.172611] pci 0000:04:07.0: PME# supported from D0 D3hot D3cold
[ 0.172732] pci 0000:03:00.0: PCI bridge to [bus 04-08]
[ 0.172740] pci 0000:03:00.0: bridge window [io 0xe000-0xefff]
[ 0.172744] pci 0000:03:00.0: bridge window [mem 0xfc400000-0xfc5fffff]
[ 0.172834] pci 0000:05:00.0: [8086:2723] type 00 class 0x028000
[ 0.172873] pci 0000:05:00.0: reg 0x10: [mem 0xfc500000-0xfc503fff 64bit]
[ 0.173081] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[ 0.173254] pci 0000:04:01.0: PCI bridge to [bus 05]
[ 0.173265] pci 0000:04:01.0: bridge window [mem 0xfc500000-0xfc5fffff]
[ 0.173319] pci 0000:04:03.0: PCI bridge to [bus 06]
[ 0.173430] pci 0000:07:00.0: [8086:1539] type 00 class 0x020000
[ 0.173469] pci 0000:07:00.0: reg 0x10: [mem 0xfc400000-0xfc41ffff]
[ 0.173510] pci 0000:07:00.0: reg 0x18: [io 0xe000-0xe01f]
[ 0.173531] pci 0000:07:00.0: reg 0x1c: [mem 0xfc420000-0xfc423fff]
[ 0.173752] pci 0000:07:00.0: PME# supported from D0 D3hot D3cold
[ 0.173940] pci 0000:04:05.0: PCI bridge to [bus 07]
[ 0.173948] pci 0000:04:05.0: bridge window [io 0xe000-0xefff]
[ 0.173952] pci 0000:04:05.0: bridge window [mem 0xfc400000-0xfc4fffff]
[ 0.174006] pci 0000:04:07.0: PCI bridge to [bus 08]
[ 0.174182] pci 0000:09:00.0: [8086:10d3] type 00 class 0x020000
[ 0.174212] pci 0000:09:00.0: reg 0x10: [mem 0xfc8c0000-0xfc8dffff]
[ 0.174226] pci 0000:09:00.0: reg 0x14: [mem 0xfc800000-0xfc87ffff]
[ 0.174240] pci 0000:09:00.0: reg 0x18: [io 0xd000-0xd01f]
[ 0.174254] pci 0000:09:00.0: reg 0x1c: [mem 0xfc8e0000-0xfc8e3fff]
[ 0.174295] pci 0000:09:00.0: reg 0x30: [mem 0xfc880000-0xfc8bffff pref]
[ 0.174428] pci 0000:09:00.0: PME# supported from D0 D3hot D3cold
[ 0.174574] pci 0000:02:05.0: PCI bridge to [bus 09]
[ 0.174580] pci 0000:02:05.0: bridge window [io 0xd000-0xdfff]
[ 0.174583] pci 0000:02:05.0: bridge window [mem 0xfc800000-0xfc8fffff]
[ 0.174698] pci 0000:0a:00.0: [1022:1485] type 00 class 0x130000
[ 0.174764] pci 0000:0a:00.0: enabling Extended Tags
[ 0.174923] pci 0000:0a:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.175085] pci 0000:0a:00.1: [1022:149c] type 00 class 0x0c0330
[ 0.175386] pci 0000:0a:00.1: reg 0x10: [mem 0xfc300000-0xfc3fffff 64bit]
[ 0.176220] pci 0000:0a:00.1: enabling Extended Tags
[ 0.176719] pci 0000:0a:00.1: PME# supported from D0 D3hot D3cold
[ 0.177126] pci 0000:0a:00.3: [1022:149c] type 00 class 0x0c0330
[ 0.177151] pci 0000:0a:00.3: reg 0x10: [mem 0xfc200000-0xfc2fffff 64bit]
[ 0.177210] pci 0000:0a:00.3: enabling Extended Tags
[ 0.177282] pci 0000:0a:00.3: PME# supported from D0 D3hot D3cold
[ 0.177406] pci 0000:02:08.0: PCI bridge to [bus 0a]
[ 0.177415] pci 0000:02:08.0: bridge window [mem 0xfc200000-0xfc3fffff]
[ 0.177510] pci 0000:0b:00.0: [1022:7901] type 00 class 0x010601
[ 0.177579] pci 0000:0b:00.0: reg 0x24: [mem 0xfc700000-0xfc7007ff]
[ 0.177598] pci 0000:0b:00.0: enabling Extended Tags
[ 0.177694] pci 0000:0b:00.0: PME# supported from D3hot D3cold
[ 0.177774] pci 0000:0b:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.177822] pci 0000:02:09.0: PCI bridge to [bus 0b]
[ 0.177830] pci 0000:02:09.0: bridge window [mem 0xfc700000-0xfc7fffff]
[ 0.177924] pci 0000:0c:00.0: [1022:7901] type 00 class 0x010601
[ 0.177993] pci 0000:0c:00.0: reg 0x24: [mem 0xfc600000-0xfc6007ff]
[ 0.178012] pci 0000:0c:00.0: enabling Extended Tags
[ 0.178109] pci 0000:0c:00.0: PME# supported from D3hot D3cold
[ 0.178188] pci 0000:0c:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.178235] pci 0000:02:0a.0: PCI bridge to [bus 0c]
[ 0.178244] pci 0000:02:0a.0: bridge window [mem 0xfc600000-0xfc6fffff]
[ 0.178327] pci 0000:0d:00.0: [10de:21c4] type 00 class 0x030000
[ 0.178341] pci 0000:0d:00.0: reg 0x10: [mem 0xfb000000-0xfbffffff]
[ 0.178353] pci 0000:0d:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.178366] pci 0000:0d:00.0: reg 0x1c: [mem 0xe0000000-0xe1ffffff 64bit pref]
[ 0.178374] pci 0000:0d:00.0: reg 0x24: [io 0xf000-0xf07f]
[ 0.178382] pci 0000:0d:00.0: reg 0x30: [mem 0xfc000000-0xfc07ffff pref]
[ 0.178400] pci 0000:0d:00.0: BAR 1: assigned to efifb
[ 0.178451] pci 0000:0d:00.0: PME# supported from D0 D3hot D3cold
[ 0.178529] pci 0000:0d:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x16 link at 0000:00:03.1 (capable of 126.016 Gb/s with 8.0 GT/s PCIe x16 link)
[ 0.178563] pci 0000:0d:00.1: [10de:1aeb] type 00 class 0x040300
[ 0.178575] pci 0000:0d:00.1: reg 0x10: [mem 0xfc080000-0xfc083fff]
[ 0.178702] pci 0000:0d:00.2: [10de:1aec] type 00 class 0x0c0330
[ 0.178720] pci 0000:0d:00.2: reg 0x10: [mem 0xe2000000-0xe203ffff 64bit pref]
[ 0.178739] pci 0000:0d:00.2: reg 0x1c: [mem 0xe2040000-0xe204ffff 64bit pref]
[ 0.178802] pci 0000:0d:00.2: PME# supported from D0 D3hot D3cold
[ 0.178851] pci 0000:0d:00.3: [10de:1aed] type 00 class 0x0c8000
[ 0.178863] pci 0000:0d:00.3: reg 0x10: [mem 0xfc084000-0xfc084fff]
[ 0.178942] pci 0000:0d:00.3: PME# supported from D0 D3hot D3cold
[ 0.179020] pci 0000:00:03.1: PCI bridge to [bus 0d]
[ 0.179023] pci 0000:00:03.1: bridge window [io 0xf000-0xffff]
[ 0.179025] pci 0000:00:03.1: bridge window [mem 0xfb000000-0xfc0fffff]
[ 0.179029] pci 0000:00:03.1: bridge window [mem 0xd0000000-0xe20fffff 64bit pref]
[ 0.179063] pci 0000:0e:00.0: [1022:148a] type 00 class 0x130000
[ 0.179090] pci 0000:0e:00.0: enabling Extended Tags
[ 0.179194] pci 0000:00:07.1: PCI bridge to [bus 0e]
[ 0.179243] pci 0000:0f:00.0: [1022:1485] type 00 class 0x130000
[ 0.179275] pci 0000:0f:00.0: enabling Extended Tags
[ 0.179382] pci 0000:0f:00.1: [1022:1486] type 00 class 0x108000
[ 0.179397] pci 0000:0f:00.1: reg 0x18: [mem 0xfca00000-0xfcafffff]
[ 0.179409] pci 0000:0f:00.1: reg 0x24: [mem 0xfcb08000-0xfcb09fff]
[ 0.179417] pci 0000:0f:00.1: enabling Extended Tags
[ 0.179513] pci 0000:0f:00.3: [1022:149c] type 00 class 0x0c0330
[ 0.179526] pci 0000:0f:00.3: reg 0x10: [mem 0xfc900000-0xfc9fffff 64bit]
[ 0.179555] pci 0000:0f:00.3: enabling Extended Tags
[ 0.179599] pci 0000:0f:00.3: PME# supported from D0 D3hot D3cold
[ 0.179662] pci 0000:0f:00.4: [1022:1487] type 00 class 0x040300
[ 0.179671] pci 0000:0f:00.4: reg 0x10: [mem 0xfcb00000-0xfcb07fff]
[ 0.179696] pci 0000:0f:00.4: enabling Extended Tags
[ 0.179738] pci 0000:0f:00.4: PME# supported from D0 D3hot D3cold
[ 0.179810] pci 0000:00:08.1: PCI bridge to [bus 0f]
[ 0.179814] pci 0000:00:08.1: bridge window [mem 0xfc900000-0xfcbfffff]
[ 0.180150] ACPI: PCI: Interrupt link LNKA configured for IRQ 0
[ 0.180192] ACPI: PCI: Interrupt link LNKB configured for IRQ 0
[ 0.180228] ACPI: PCI: Interrupt link LNKC configured for IRQ 0
[ 0.180273] ACPI: PCI: Interrupt link LNKD configured for IRQ 0
[ 0.180313] ACPI: PCI: Interrupt link LNKE configured for IRQ 0
[ 0.180346] ACPI: PCI: Interrupt link LNKF configured for IRQ 0
[ 0.180379] ACPI: PCI: Interrupt link LNKG configured for IRQ 0
[ 0.180412] ACPI: PCI: Interrupt link LNKH configured for IRQ 0
[ 0.180837] iommu: Default domain type: Translated
[ 0.180837] iommu: DMA domain TLB invalidation policy: lazy mode
[ 0.180837] SCSI subsystem initialized
[ 0.180837] libata version 3.00 loaded.
[ 0.180837] ACPI: bus type USB registered
[ 0.180837] usbcore: registered new interface driver usbfs
[ 0.180837] usbcore: registered new interface driver hub
[ 0.180837] usbcore: registered new device driver usb
[ 0.180837] pps_core: LinuxPPS API ver. 1 registered
[ 0.180837] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.180837] PTP clock support registered
[ 0.180837] EDAC MC: Ver: 3.0.0
[ 0.180837] Registered efivars operations
[ 0.180837] NetLabel: Initializing
[ 0.180837] NetLabel: domain hash size = 128
[ 0.180837] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.180837] NetLabel: unlabeled traffic allowed by default
[ 0.180837] mctp: management component transport protocol core
[ 0.180837] NET: Registered PF_MCTP protocol family
[ 0.180837] PCI: Using ACPI for IRQ routing
[ 0.185126] PCI: pci_cache_line_size set to 64 bytes
[ 0.185251] e820: reserve RAM buffer [mem 0x09aff000-0x0bffffff]
[ 0.185252] e820: reserve RAM buffer [mem 0x0a200000-0x0bffffff]
[ 0.185252] e820: reserve RAM buffer [mem 0xc5966018-0xc7ffffff]
[ 0.185253] e820: reserve RAM buffer [mem 0xc5987018-0xc7ffffff]
[ 0.185254] e820: reserve RAM buffer [mem 0xc5a6b000-0xc7ffffff]
[ 0.185255] e820: reserve RAM buffer [mem 0xc781d000-0xc7ffffff]
[ 0.185255] e820: reserve RAM buffer [mem 0xc78d6000-0xc7ffffff]
[ 0.185256] e820: reserve RAM buffer [mem 0xcb61b000-0xcbffffff]
[ 0.185256] e820: reserve RAM buffer [mem 0xcf000000-0xcfffffff]
[ 0.185257] e820: reserve RAM buffer [mem 0x42f380000-0x42fffffff]
[ 0.185263] pci 0000:0d:00.0: vgaarb: setting as boot VGA device
[ 0.185263] pci 0000:0d:00.0: vgaarb: bridge control possible
[ 0.185263] pci 0000:0d:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
[ 0.185263] vgaarb: loaded
[ 0.185263] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.185263] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.186413] clocksource: Switched to clocksource tsc-early
[ 0.190187] VFS: Disk quotas dquot_6.6.0
[ 0.190198] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.190265] AppArmor: AppArmor Filesystem Enabled
[ 0.190285] pnp: PnP ACPI init
[ 0.190363] system 00:00: [mem 0xf0000000-0xf7ffffff] has been reserved
[ 0.190385] system 00:01: [mem 0xfeb80000-0xfebfffff] has been reserved
[ 0.190442] system 00:02: [mem 0xfd200000-0xfd2fffff] has been reserved
[ 0.190613] system 00:04: [io 0x0280-0x028f] has been reserved
[ 0.190615] system 00:04: [io 0x0290-0x029f] has been reserved
[ 0.190616] system 00:04: [io 0x02a0-0x02af] has been reserved
[ 0.190616] system 00:04: [io 0x02b0-0x02bf] has been reserved
[ 0.190815] pnp 00:05: [dma 0 disabled]
[ 0.191025] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.191026] system 00:06: [io 0x040b] has been reserved
[ 0.191027] system 00:06: [io 0x04d6] has been reserved
[ 0.191028] system 00:06: [io 0x0c00-0x0c01] has been reserved
[ 0.191029] system 00:06: [io 0x0c14] has been reserved
[ 0.191029] system 00:06: [io 0x0c50-0x0c51] has been reserved
[ 0.191030] system 00:06: [io 0x0c52] has been reserved
[ 0.191031] system 00:06: [io 0x0c6c] has been reserved
[ 0.191032] system 00:06: [io 0x0c6f] has been reserved
[ 0.191032] system 00:06: [io 0x0cd0-0x0cd1] has been reserved
[ 0.191033] system 00:06: [io 0x0cd2-0x0cd3] has been reserved
[ 0.191034] system 00:06: [io 0x0cd4-0x0cd5] has been reserved
[ 0.191035] system 00:06: [io 0x0cd6-0x0cd7] has been reserved
[ 0.191036] system 00:06: [io 0x0cd8-0x0cdf] has been reserved
[ 0.191036] system 00:06: [io 0x0800-0x089f] has been reserved
[ 0.191038] system 00:06: [io 0x0b00-0x0b0f] has been reserved
[ 0.191039] system 00:06: [io 0x0b20-0x0b3f] has been reserved
[ 0.191039] system 00:06: [io 0x0900-0x090f] has been reserved
[ 0.191040] system 00:06: [io 0x0910-0x091f] has been reserved
[ 0.191041] system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.191042] system 00:06: [mem 0xfec01000-0xfec01fff] could not be reserved
[ 0.191043] system 00:06: [mem 0xfedc0000-0xfedc0fff] has been reserved
[ 0.191044] system 00:06: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.191045] system 00:06: [mem 0xfed80000-0xfed8ffff] could not be reserved
[ 0.191046] system 00:06: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.191047] system 00:06: [mem 0xff000000-0xffffffff] has been reserved
[ 0.191436] pnp: PnP ACPI: found 7 devices
[ 0.196822] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.196861] NET: Registered PF_INET protocol family
[ 0.197017] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.197968] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 0.198066] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.198223] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 0.198284] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.198365] MPTCP token hash table entries: 16384 (order: 6, 393216 bytes, linear)
[ 0.198401] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.198434] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.198481] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.198484] NET: Registered PF_XDP protocol family
[ 0.198496] pci 0000:04:01.0: PCI bridge to [bus 05]
[ 0.198503] pci 0000:04:01.0: bridge window [mem 0xfc500000-0xfc5fffff]
[ 0.198515] pci 0000:04:03.0: PCI bridge to [bus 06]
[ 0.198532] pci 0000:04:05.0: PCI bridge to [bus 07]
[ 0.198535] pci 0000:04:05.0: bridge window [io 0xe000-0xefff]
[ 0.198540] pci 0000:04:05.0: bridge window [mem 0xfc400000-0xfc4fffff]
[ 0.198552] pci 0000:04:07.0: PCI bridge to [bus 08]
[ 0.198568] pci 0000:03:00.0: PCI bridge to [bus 04-08]
[ 0.198570] pci 0000:03:00.0: bridge window [io 0xe000-0xefff]
[ 0.198576] pci 0000:03:00.0: bridge window [mem 0xfc400000-0xfc5fffff]
[ 0.198587] pci 0000:02:03.0: PCI bridge to [bus 03-08]
[ 0.198589] pci 0000:02:03.0: bridge window [io 0xe000-0xefff]
[ 0.198594] pci 0000:02:03.0: bridge window [mem 0xfc400000-0xfc5fffff]
[ 0.198603] pci 0000:02:05.0: PCI bridge to [bus 09]
[ 0.198605] pci 0000:02:05.0: bridge window [io 0xd000-0xdfff]
[ 0.198609] pci 0000:02:05.0: bridge window [mem 0xfc800000-0xfc8fffff]
[ 0.198618] pci 0000:02:08.0: PCI bridge to [bus 0a]
[ 0.198623] pci 0000:02:08.0: bridge window [mem 0xfc200000-0xfc3fffff]
[ 0.198632] pci 0000:02:09.0: PCI bridge to [bus 0b]
[ 0.198636] pci 0000:02:09.0: bridge window [mem 0xfc700000-0xfc7fffff]
[ 0.198645] pci 0000:02:0a.0: PCI bridge to [bus 0c]
[ 0.198650] pci 0000:02:0a.0: bridge window [mem 0xfc600000-0xfc6fffff]
[ 0.198659] pci 0000:01:00.0: PCI bridge to [bus 02-0c]
[ 0.198660] pci 0000:01:00.0: bridge window [io 0xd000-0xefff]
[ 0.198665] pci 0000:01:00.0: bridge window [mem 0xfc200000-0xfc8fffff]
[ 0.198674] pci 0000:00:01.2: PCI bridge to [bus 01-0c]
[ 0.198676] pci 0000:00:01.2: bridge window [io 0xd000-0xefff]
[ 0.198679] pci 0000:00:01.2: bridge window [mem 0xfc200000-0xfc8fffff]
[ 0.198683] pci 0000:00:03.1: PCI bridge to [bus 0d]
[ 0.198684] pci 0000:00:03.1: bridge window [io 0xf000-0xffff]
[ 0.198687] pci 0000:00:03.1: bridge window [mem 0xfb000000-0xfc0fffff]
[ 0.198689] pci 0000:00:03.1: bridge window [mem 0xd0000000-0xe20fffff 64bit pref]
[ 0.198693] pci 0000:00:07.1: PCI bridge to [bus 0e]
[ 0.198699] pci 0000:00:08.1: PCI bridge to [bus 0f]
[ 0.198701] pci 0000:00:08.1: bridge window [mem 0xfc900000-0xfcbfffff]
[ 0.198705] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 0.198706] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.198707] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 0.198708] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.198709] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000dffff window]
[ 0.198710] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xfec02fff window]
[ 0.198710] pci_bus 0000:00: resource 10 [mem 0xfee00000-0xffffffff window]
[ 0.198711] pci_bus 0000:01: resource 0 [io 0xd000-0xefff]
[ 0.198712] pci_bus 0000:01: resource 1 [mem 0xfc200000-0xfc8fffff]
[ 0.198713] pci_bus 0000:02: resource 0 [io 0xd000-0xefff]
[ 0.198713] pci_bus 0000:02: resource 1 [mem 0xfc200000-0xfc8fffff]
[ 0.198714] pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
[ 0.198715] pci_bus 0000:03: resource 1 [mem 0xfc400000-0xfc5fffff]
[ 0.198716] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.198717] pci_bus 0000:04: resource 1 [mem 0xfc400000-0xfc5fffff]
[ 0.198718] pci_bus 0000:05: resource 1 [mem 0xfc500000-0xfc5fffff]
[ 0.198718] pci_bus 0000:07: resource 0 [io 0xe000-0xefff]
[ 0.198719] pci_bus 0000:07: resource 1 [mem 0xfc400000-0xfc4fffff]
[ 0.198720] pci_bus 0000:09: resource 0 [io 0xd000-0xdfff]
[ 0.198721] pci_bus 0000:09: resource 1 [mem 0xfc800000-0xfc8fffff]
[ 0.198722] pci_bus 0000:0a: resource 1 [mem 0xfc200000-0xfc3fffff]
[ 0.198723] pci_bus 0000:0b: resource 1 [mem 0xfc700000-0xfc7fffff]
[ 0.198723] pci_bus 0000:0c: resource 1 [mem 0xfc600000-0xfc6fffff]
[ 0.198724] pci_bus 0000:0d: resource 0 [io 0xf000-0xffff]
[ 0.198725] pci_bus 0000:0d: resource 1 [mem 0xfb000000-0xfc0fffff]
[ 0.198726] pci_bus 0000:0d: resource 2 [mem 0xd0000000-0xe20fffff 64bit pref]
[ 0.198727] pci_bus 0000:0f: resource 1 [mem 0xfc900000-0xfcbfffff]
[ 0.199138] pci 0000:0d:00.1: D0 power state depends on 0000:0d:00.0
[ 0.199191] pci 0000:0d:00.2: D0 power state depends on 0000:0d:00.0
[ 0.199301] pci 0000:0d:00.3: D0 power state depends on 0000:0d:00.0
[ 0.199417] PCI: CLS 64 bytes, default 64
[ 0.199422] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.199422] software IO TLB: mapped [mem 0x00000000c1966000-0x00000000c5966000] (64MB)
[ 0.199453] LVT offset 0 assigned for vector 0x400
[ 0.199464] Trying to unpack rootfs image as initramfs...
[ 0.211758] perf: AMD IBS detected (0x000003ff)
[ 0.212229] Initialise system trusted keyrings
[ 0.212237] Key type blacklist registered
[ 0.212302] workingset: timestamp_bits=36 max_order=22 bucket_order=0
[ 0.213027] zbud: loaded
[ 0.213203] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.213293] fuse: init (API version 7.36)
[ 0.213391] integrity: Platform Keyring initialized
[ 0.213393] integrity: Machine keyring initialized
[ 0.215706] Key type asymmetric registered
[ 0.215706] Asymmetric key parser 'x509' registered
[ 0.375598] Freeing initrd memory: 127280K
[ 0.377449] alg: self-tests for CTR-KDF (hmac(sha256)) passed
[ 0.377466] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 0.377499] io scheduler mq-deadline registered
[ 0.378940] pcieport 0000:00:01.2: PME: Signaling with IRQ 26
[ 0.379020] pcieport 0000:00:01.2: AER: enabled with IRQ 26
[ 0.379113] pcieport 0000:00:03.1: PME: Signaling with IRQ 27
[ 0.379163] pcieport 0000:00:03.1: AER: enabled with IRQ 27
[ 0.379316] pcieport 0000:00:07.1: PME: Signaling with IRQ 29
[ 0.379369] pcieport 0000:00:07.1: AER: enabled with IRQ 29
[ 0.379446] pcieport 0000:00:08.1: PME: Signaling with IRQ 30
[ 0.379496] pcieport 0000:00:08.1: AER: enabled with IRQ 30
[ 0.381505] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.381602] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.381614] ACPI: button: Power Button [PWRB]
[ 0.381631] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.381654] ACPI: button: Power Button [PWRF]
[ 0.383794] smpboot: Estimated ratio of average max frequency by base frequency (times 1024): 1106
[ 0.383802] Monitor-Mwait will be used to enter C-1 state
[ 0.383806] ACPI: \_PR_.C000: Found 2 idle states
[ 0.383868] ACPI: \_PR_.C002: Found 2 idle states
[ 0.383966] ACPI: \_PR_.C004: Found 2 idle states
[ 0.384065] ACPI: \_PR_.C006: Found 2 idle states
[ 0.384164] ACPI: \_PR_.C008: Found 2 idle states
[ 0.384258] ACPI: \_PR_.C00A: Found 2 idle states
[ 0.384340] ACPI: \_PR_.C001: Found 2 idle states
[ 0.384398] ACPI: \_PR_.C003: Found 2 idle states
[ 0.384484] ACPI: \_PR_.C005: Found 2 idle states
[ 0.384576] ACPI: \_PR_.C007: Found 2 idle states
[ 0.384668] ACPI: \_PR_.C009: Found 2 idle states
[ 0.384755] ACPI: \_PR_.C00B: Found 2 idle states
[ 0.384937] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.405476] 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.407011] Linux agpgart interface v0.103
[ 0.409475] loop: module loaded
[ 0.409607] tun: Universal TUN/TAP device driver, 1.6
[ 0.409636] PPP generic driver version 2.4.2
[ 0.409668] VFIO - User Level meta-driver version: 0.3
[ 0.409704] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.409705] ehci-pci: EHCI PCI platform driver
[ 0.409711] ehci-platform: EHCI generic platform driver
[ 0.409714] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.409715] ohci-pci: OHCI PCI platform driver
[ 0.409720] ohci-platform: OHCI generic platform driver
[ 0.409723] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.409742] i8042: PNP: No PS/2 controller found.
[ 0.409768] mousedev: PS/2 mouse device common for all mice
[ 0.409823] rtc_cmos 00:03: RTC can wake from S4
[ 0.409987] rtc_cmos 00:03: registered as rtc0
[ 0.410014] rtc_cmos 00:03: setting system clock to 2022-05-27T09:54:17 UTC (1653645257)
[ 0.410022] rtc_cmos 00:03: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.410026] i2c_dev: i2c /dev entries driver
[ 0.410035] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log.
[ 0.410047] device-mapper: uevent: version 1.0.3
[ 0.410071] device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com
[ 0.410079] platform eisa.0: Probing EISA bus 0
[ 0.410080] platform eisa.0: EISA: Cannot allocate resource for mainboard
[ 0.410081] platform eisa.0: Cannot allocate resource for EISA slot 1
[ 0.410082] platform eisa.0: Cannot allocate resource for EISA slot 2
[ 0.410082] platform eisa.0: Cannot allocate resource for EISA slot 3
[ 0.410083] platform eisa.0: Cannot allocate resource for EISA slot 4
[ 0.410083] platform eisa.0: Cannot allocate resource for EISA slot 5
[ 0.410084] platform eisa.0: Cannot allocate resource for EISA slot 6
[ 0.410085] platform eisa.0: Cannot allocate resource for EISA slot 7
[ 0.410085] platform eisa.0: Cannot allocate resource for EISA slot 8
[ 0.410086] platform eisa.0: EISA: Detected 0 cards
[ 0.410539] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.410549] efifb: probing for efifb
[ 0.410589] efifb: showing boot graphics
[ 0.412916] efifb: framebuffer at 0xd0000000, using 8400k, total 8400k
[ 0.412917] efifb: mode is 1680x1050x32, linelength=8192, pages=1
[ 0.412918] efifb: scrolling: redraw
[ 0.412918] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.412957] fbcon: Deferring console take-over
[ 0.412958] fb0: EFI VGA frame buffer device
[ 0.412961] EFI Variables Facility v0.08 2004-May-17
[ 0.413847] drop_monitor: Initializing network drop monitor service
[ 0.424141] IPv6: Loaded, but administratively disabled, reboot required to enable
[ 0.424142] NET: Registered PF_PACKET protocol family
[ 0.424181] Key type dns_resolver registered
[ 0.424917] microcode: CPU0: patch_level=0x08701021
[ 0.424920] microcode: CPU1: patch_level=0x08701021
[ 0.424933] microcode: CPU2: patch_level=0x08701021
[ 0.424949] microcode: CPU3: patch_level=0x08701021
[ 0.424965] microcode: CPU4: patch_level=0x08701021
[ 0.424981] microcode: CPU5: patch_level=0x08701021
[ 0.424987] microcode: CPU6: patch_level=0x08701021
[ 0.424991] microcode: CPU7: patch_level=0x08701021
[ 0.424996] microcode: CPU8: patch_level=0x08701021
[ 0.425002] microcode: CPU9: patch_level=0x08701021
[ 0.425007] microcode: CPU10: patch_level=0x08701021
[ 0.425013] microcode: CPU11: patch_level=0x08701021
[ 0.425035] microcode: Microcode Update Driver: v2.2.
[ 0.425139] resctrl: L3 allocation detected
[ 0.425140] resctrl: MB allocation detected
[ 0.425140] resctrl: L3 monitoring detected
[ 0.425142] IPI shorthand broadcast: enabled
[ 0.425146] sched_clock: Marking stable (453127042, -27995520)->(430366584, -5235062)
[ 0.425410] registered taskstats version 1
[ 0.425527] Loading compiled-in X.509 certificates
[ 0.425953] Loaded X.509 cert 'Build time autogenerated kernel key: 9f39f1a9a84b110de589941f1b818eb21eb7a201'
[ 0.426280] Loaded X.509 cert 'Canonical Ltd. Live Patch Signing: 14df34d1a87cf37625abec039ef2bf521249b969'
[ 0.426603] Loaded X.509 cert 'Canonical Ltd. Kernel Module Signing: 88f752e560a1e0737e31163a466ad7b70a850c19'
[ 0.426604] blacklist: Loading compiled-in revocation X.509 certificates
[ 0.426615] Loaded X.509 cert 'Canonical Ltd. Secure Boot Signing: 61482aa2830d0ab2ad5af10b7250da9033ddcef0'
[ 0.427238] zswap: loaded using pool lzo/zbud
[ 0.427340] Key type ._fscrypt registered
[ 0.427340] Key type .fscrypt registered
[ 0.427341] Key type fscrypt-provisioning registered
[ 0.429192] Key type encrypted registered
[ 0.429193] AppArmor: AppArmor sha1 policy hashing enabled
[ 0.429248] ima: No TPM chip found, activating TPM-bypass!
[ 0.429249] Loading compiled-in module X.509 certificates
[ 0.429597] Loaded X.509 cert 'Build time autogenerated kernel key: 9f39f1a9a84b110de589941f1b818eb21eb7a201'
[ 0.429598] ima: Allocated hash algorithm: sha1
[ 0.429602] ima: No architecture policies found
[ 0.429607] evm: Initialising EVM extended attributes:
[ 0.429608] evm: security.selinux
[ 0.429608] evm: security.SMACK64
[ 0.429609] evm: security.SMACK64EXEC
[ 0.429609] evm: security.SMACK64TRANSMUTE
[ 0.429609] evm: security.SMACK64MMAP
[ 0.429610] evm: security.apparmor
[ 0.429610] evm: security.ima
[ 0.429610] evm: security.capability
[ 0.429611] evm: HMAC attrs: 0x1
[ 0.430473] PM: Magic number: 6:866:930
[ 0.430781] acpi_cpufreq: overriding BIOS provided _PSD data
[ 0.475453] RAS: Correctable Errors collector initialized.
[ 0.476890] Freeing unused decrypted memory: 2036K
[ 0.477199] Freeing unused kernel image (initmem) memory: 2764K
[ 0.479409] Write protecting the kernel read-only data: 30720k
[ 0.480121] Freeing unused kernel image (text/rodata gap) memory: 2036K
[ 0.480318] Freeing unused kernel image (rodata/data gap) memory: 1312K
[ 0.510496] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.510505] Run /init as init process
[ 0.510506] with arguments:
[ 0.510507] /init
[ 0.510508] splash
[ 0.510508] with environment:
[ 0.510508] HOME=/
[ 0.510509] TERM=linux
[ 0.510509] BOOT_IMAGE=/vmlinuz-5.18.0-051800-generic
[ 0.557187] dca service started, version 1.12.1
[ 0.558312] xhci_hcd 0000:0a:00.1: xHCI Host Controller
[ 0.558318] xhci_hcd 0000:0a:00.1: new USB bus registered, assigned bus number 1
[ 0.558484] xhci_hcd 0000:0a:00.1: hcc params 0x0278ffe5 hci version 0x110 quirks 0x0000000000000410
[ 0.558521] ahci 0000:0b:00.0: version 3.0
[ 0.558982] nvidia-gpu 0000:0d:00.3: enabling device (0000 -> 0002)
[ 0.559049] ahci 0000:0b:00.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x9 impl SATA mode
[ 0.559052] ahci 0000:0b:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part
[ 0.559120] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18
[ 0.559123] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.559125] usb usb1: Product: xHCI Host Controller
[ 0.559126] usb usb1: Manufacturer: Linux 5.18.0-051800-generic xhci-hcd
[ 0.559127] usb usb1: SerialNumber: 0000:0a:00.1
[ 0.559433] hub 1-0:1.0: USB hub found
[ 0.559447] hub 1-0:1.0: 6 ports detected
[ 0.559585] scsi host0: ahci
[ 0.559809] xhci_hcd 0000:0a:00.1: xHCI Host Controller
[ 0.559813] xhci_hcd 0000:0a:00.1: new USB bus registered, assigned bus number 2
[ 0.559815] xhci_hcd 0000:0a:00.1: Host supports USB 3.1 Enhanced SuperSpeed
[ 0.559816] scsi host1: ahci
[ 0.559837] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.559855] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.18
[ 0.559858] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.559859] usb usb2: Product: xHCI Host Controller
[ 0.559860] usb usb2: Manufacturer: Linux 5.18.0-051800-generic xhci-hcd
[ 0.559861] usb usb2: SerialNumber: 0000:0a:00.1
[ 0.559918] scsi host2: ahci
[ 0.559933] hub 2-0:1.0: USB hub found
[ 0.559942] hub 2-0:1.0: 4 ports detected
[ 0.560008] scsi host3: ahci
[ 0.560051] ata1: SATA max UDMA/133 abar m2048@0xfc700000 port 0xfc700100 irq 45
[ 0.560053] ata2: DUMMY
[ 0.560054] ata3: DUMMY
[ 0.560057] ata4: SATA max UDMA/133 abar m2048@0xfc700000 port 0xfc700280 irq 45
[ 0.560157] xhci_hcd 0000:0a:00.3: xHCI Host Controller
[ 0.560160] xhci_hcd 0000:0a:00.3: new USB bus registered, assigned bus number 3
[ 0.560234] ahci 0000:0c:00.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x11 impl SATA mode
[ 0.560237] ahci 0000:0c:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part
[ 0.560317] xhci_hcd 0000:0a:00.3: hcc params 0x0278ffe5 hci version 0x110 quirks 0x0000000000000410
[ 0.560587] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 0.560589] piix4_smbus 0000:00:14.0: Using register 0x02 for SMBus port selection
[ 0.560622] scsi host4: ahci
[ 0.560626] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18
[ 0.560629] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.560630] usb usb3: Product: xHCI Host Controller
[ 0.560631] usb usb3: Manufacturer: Linux 5.18.0-051800-generic xhci-hcd
[ 0.560632] usb usb3: SerialNumber: 0000:0a:00.3
[ 0.560727] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[ 0.560804] hub 3-0:1.0: USB hub found
[ 0.560818] hub 3-0:1.0: 6 ports detected
[ 0.560909] scsi host5: ahci
[ 0.560997] scsi host6: ahci
[ 0.561060] xhci_hcd 0000:0a:00.3: xHCI Host Controller
[ 0.561063] xhci_hcd 0000:0a:00.3: new USB bus registered, assigned bus number 4
[ 0.561065] xhci_hcd 0000:0a:00.3: Host supports USB 3.1 Enhanced SuperSpeed
[ 0.561091] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.561107] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.18
[ 0.561109] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.561111] usb usb4: Product: xHCI Host Controller
[ 0.561112] usb usb4: Manufacturer: Linux 5.18.0-051800-generic xhci-hcd
[ 0.561113] usb usb4: SerialNumber: 0000:0a:00.3
[ 0.561213] scsi host7: ahci
[ 0.561241] hub 4-0:1.0: USB hub found
[ 0.561252] hub 4-0:1.0: 4 ports detected
[ 0.561295] usb: port power management may be unreliable
[ 0.561337] scsi host8: ahci
[ 0.561372] ata5: SATA max UDMA/133 abar m2048@0xfc600000 port 0xfc600100 irq 48
[ 0.561373] ata6: DUMMY
[ 0.561373] ata7: DUMMY
[ 0.561374] ata8: DUMMY
[ 0.561377] ata9: SATA max UDMA/133 abar m2048@0xfc600000 port 0xfc600300 irq 48
[ 0.561550] e1000e: Intel(R) PRO/1000 Network Driver
[ 0.561551] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 0.561572] xhci_hcd 0000:0d:00.2: xHCI Host Controller
[ 0.561575] xhci_hcd 0000:0d:00.2: new USB bus registered, assigned bus number 5
[ 0.561582] e1000e 0000:09:00.0: enabling device (0000 -> 0002)
[ 0.561740] e1000e 0000:09:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 0.562171] xhci_hcd 0000:0d:00.2: hcc params 0x0180ff05 hci version 0x110 quirks 0x0000000000000010
[ 0.562184] igb: Intel(R) Gigabit Ethernet Network Driver
[ 0.562186] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 0.562318] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18
[ 0.562320] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.562320] usb usb5: Product: xHCI Host Controller
[ 0.562321] usb usb5: Manufacturer: Linux 5.18.0-051800-generic xhci-hcd
[ 0.562322] usb usb5: SerialNumber: 0000:0d:00.2
[ 0.562377] hub 5-0:1.0: USB hub found
[ 0.562383] hub 5-0:1.0: 2 ports detected
[ 0.562459] xhci_hcd 0000:0d:00.2: xHCI Host Controller
[ 0.562461] xhci_hcd 0000:0d:00.2: new USB bus registered, assigned bus number 6
[ 0.562463] xhci_hcd 0000:0d:00.2: Host supports USB 3.1 Enhanced SuperSpeed
[ 0.562480] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.562491] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.18
[ 0.562492] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.562493] usb usb6: Product: xHCI Host Controller
[ 0.562493] usb usb6: Manufacturer: Linux 5.18.0-051800-generic xhci-hcd
[ 0.562494] usb usb6: SerialNumber: 0000:0d:00.2
[ 0.562552] hub 6-0:1.0: USB hub found
[ 0.562560] hub 6-0:1.0: 4 ports detected
[ 0.562749] xhci_hcd 0000:0f:00.3: xHCI Host Controller
[ 0.562753] xhci_hcd 0000:0f:00.3: new USB bus registered, assigned bus number 7
[ 0.562855] xhci_hcd 0000:0f:00.3: hcc params 0x0278ffe5 hci version 0x110 quirks 0x0000000000000410
[ 0.563054] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18
[ 0.563056] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.563057] usb usb7: Product: xHCI Host Controller
[ 0.563057] usb usb7: Manufacturer: Linux 5.18.0-051800-generic xhci-hcd
[ 0.563058] usb usb7: SerialNumber: 0000:0f:00.3
[ 0.563117] hub 7-0:1.0: USB hub found
[ 0.563124] hub 7-0:1.0: 4 ports detected
[ 0.563231] xhci_hcd 0000:0f:00.3: xHCI Host Controller
[ 0.563233] xhci_hcd 0000:0f:00.3: new USB bus registered, assigned bus number 8
[ 0.563235] xhci_hcd 0000:0f:00.3: Host supports USB 3.1 Enhanced SuperSpeed
[ 0.563247] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.563258] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.18
[ 0.563259] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.563260] usb usb8: Product: xHCI Host Controller
[ 0.563260] usb usb8: Manufacturer: Linux 5.18.0-051800-generic xhci-hcd
[ 0.563261] usb usb8: SerialNumber: 0000:0f:00.3
[ 0.563313] hub 8-0:1.0: USB hub found
[ 0.563319] hub 8-0:1.0: 4 ports detected
[ 0.564620] cryptd: max_cpu_qlen set to 1000
[ 0.567929] AVX2 version of gcm_enc/dec engaged.
[ 0.567959] AES CTR mode by8 optimization enabled
[ 0.597975] pps pps0: new PPS source ptp0
[ 0.597999] igb 0000:07:00.0: added PHC on eth0
[ 0.598000] igb 0000:07:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 0.598001] igb 0000:07:00.0: eth0: (PCIe:2.5Gb/s:Width x1) 70:85:c2:f0:45:d9
[ 0.598003] igb 0000:07:00.0: eth0: PBA No: FFFFFF-0FF
[ 0.598004] igb 0000:07:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx queue(s)
[ 0.624386] e1000e 0000:09:00.0 0000:09:00.0 (uninitialized): registered PHC clock
[ 0.688318] e1000e 0000:09:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 68:05:ca:0c:63:13
[ 0.688321] e1000e 0000:09:00.0 eth1: Intel(R) PRO/1000 Network Connection
[ 0.688336] e1000e 0000:09:00.0 eth1: MAC: 3, PHY: 8, PBA No: E46981-007
[ 0.814258] usb 1-1: new full-speed USB device number 2 using xhci_hcd
[ 0.818257] usb 3-4: new high-speed USB device number 2 using xhci_hcd
[ 0.818262] usb 7-3: new low-speed USB device number 2 using xhci_hcd
[ 0.971471] usb 3-4: New USB device found, idVendor=04a9, idProduct=1748, bcdDevice= 0.04
[ 0.971474] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 0.971475] usb 3-4: Product: MG5100 series
[ 0.971476] usb 3-4: Manufacturer: Canon
[ 0.971477] usb 3-4: SerialNumber: 25E702
[ 0.984865] usb 1-1: New USB device found, idVendor=046d, idProduct=c52b, bcdDevice=12.11
[ 0.984867] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 0.984868] usb 1-1: Product: USB Receiver
[ 0.984869] usb 1-1: Manufacturer: Logitech
[ 0.993336] usb 7-3: New USB device found, idVendor=060b, idProduct=2312, bcdDevice= 1.70
[ 0.993338] usb 7-3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 0.993339] usb 7-3: Product: Gaming Keyboard
[ 1.020578] usb-storage 3-4:1.2: USB Mass Storage device detected
[ 1.020662] hid: raw HID events driver (C) Jiri Kosina
[ 1.020663] scsi host9: usb-storage 3-4:1.2
[ 1.020728] usbcore: registered new interface driver usb-storage
[ 1.040032] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.043657] ata1.00: ATAPI: PIONEER BD-RW BDR-207M, 1.60, max UDMA/100
[ 1.044028] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.044029] ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.044053] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.044492] ata9.00: ATA-10: WDC WD40EFRX-68N32N0, 82.00A82, max UDMA/133
[ 1.044786] ata5.00: supports DRM functions and may not be fully accessible
[ 1.044787] ata5.00: ATA-10: CT1000MX500SSD1, M3CR032, max UDMA/133
[ 1.044813] ata5.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 1.045028] ata9.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 1.045546] ata5.00: Features: Trust Dev-Sleep
[ 1.045648] ata5.00: supports DRM functions and may not be fully accessible
[ 1.046056] ata9.00: configured for UDMA/133
[ 1.046378] ata5.00: configured for UDMA/133
[ 1.047015] ata4.00: ATA-8: WDC WD20EADS-00W4B0, 01.00A01, max UDMA/133
[ 1.047251] ata4.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 1.047484] ata1.00: configured for UDMA/100
[ 1.049551] ata4.00: configured for UDMA/133
[ 1.057988] scsi 0:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.60 PQ: 0 ANSI: 5
[ 1.090956] usbcore: registered new interface driver usbhid
[ 1.090959] usbhid: USB HID core driver
[ 1.144014] usb 1-2: new high-speed USB device number 3 using xhci_hcd
[ 1.144021] usb 3-5: new high-speed USB device number 3 using xhci_hcd
[ 1.156071] sr 0:0:0:0: [sr0] scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.156075] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.188989] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.189036] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 1.189265] scsi 3:0:0:0: Direct-Access ATA WDC WD20EADS-00W 0A01 PQ: 0 ANSI: 5
[ 1.189406] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 1.189505] sd 3:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 1.189513] sd 3:0:0:0: [sda] Write Protect is off
[ 1.189517] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.189530] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.189568] scsi 4:0:0:0: Direct-Access ATA CT1000MX500SSD1 032 PQ: 0 ANSI: 5
[ 1.189710] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 1.189824] sd 4:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 1.189828] sd 4:0:0:0: [sdb] 4096-byte physical blocks
[ 1.189839] sd 4:0:0:0: [sdb] Write Protect is off
[ 1.189842] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.189856] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.189874] scsi 8:0:0:0: Direct-Access ATA WDC WD40EFRX-68N 0A82 PQ: 0 ANSI: 5
[ 1.189988] sd 8:0:0:0: Attached scsi generic sg3 type 0
[ 1.190109] sd 8:0:0:0: [sdc] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 1.190113] sd 8:0:0:0: [sdc] 4096-byte physical blocks
[ 1.190122] sd 8:0:0:0: [sdc] Write Protect is off
[ 1.190124] sd 8:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1.190140] sd 8:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.220018] tsc: Refined TSC clocksource calibration: 3799.935 MHz
[ 1.220026] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x6d8c35d3b02, max_idle_ns: 881590614458 ns
[ 1.220057] clocksource: Switched to clocksource tsc
[ 1.222830] sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6
[ 1.248211] sd 4:0:0:0: [sdb] supports TCG Opal
[ 1.248213] sd 4:0:0:0: [sdb] Attached SCSI disk
[ 1.268043] sdc: sdc1 sdc2
[ 1.292977] usb 3-5: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[ 1.292982] usb 3-5: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.295107] usb 1-2: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=88.32
[ 1.295111] usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.295113] usb 1-2: Product: USB2.0 Hub
[ 1.300070] sd 8:0:0:0: [sdc] Attached SCSI disk
[ 1.328272] hub 1-2:1.0: USB hub found
[ 1.328861] hub 1-2:1.0: 4 ports detected
[ 1.329254] hub 3-5:1.0: USB hub found
[ 1.329602] hub 3-5:1.0: 4 ports detected
[ 1.620472] usb 1-2.2: new high-speed USB device number 4 using xhci_hcd
[ 1.685252] sda: sda1
[ 1.700528] sd 3:0:0:0: [sda] Attached SCSI disk
[ 1.701960] igb 0000:07:00.0 enp7s0: renamed from eth0
[ 1.702219] usbcore: registered new interface driver uas
[ 1.704189] input: Gaming Keyboard as /devices/pci0000:00/0000:00:08.1/0000:0f:00.3/usb7/7-3/7-3:1.0/0003:060B:2312.0001/input/input2
[ 1.728193] e1000e 0000:09:00.0 enp9s0: renamed from eth1
[ 1.728878] usb 1-2.2: New USB device found, idVendor=05e3, idProduct=0716, bcdDevice=97.44
[ 1.728883] usb 1-2.2: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[ 1.728886] usb 1-2.2: Product: USB Storage
[ 1.728888] usb 1-2.2: SerialNumber: 000000009744
[ 1.729631] usb-storage 1-2.2:1.0: USB Mass Storage device detected
[ 1.729718] scsi host10: usb-storage 1-2.2:1.0
[ 1.764267] hid-generic 0003:060B:2312.0001: input,hidraw0: USB HID v1.11 Keyboard [Gaming Keyboard] on usb-0000:0f:00.3-3/input0
[ 1.764454] input: Gaming Keyboard as /devices/pci0000:00/0000:00:08.1/0000:0f:00.3/usb7/7-3/7-3:1.1/0003:060B:2312.0002/input/input3
[ 1.824163] hid-generic 0003:060B:2312.0002: input,hidraw1: USB HID v1.11 Keyboard [Gaming Keyboard] on usb-0000:0f:00.3-3/input1
[ 1.824343] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:01.2/0000:01:00.0/0000:02:08.0/0000:0a:00.1/usb1/1-1/1-1:1.0/0003:046D:C52B.0003/input/input4
[ 1.884103] hid-generic 0003:046D:C52B.0003: input,hidraw2: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:0a:00.1-1/input0
[ 1.884324] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:01.2/0000:01:00.0/0000:02:08.0/0000:0a:00.1/usb1/1-1/1-1:1.1/0003:046D:C52B.0004/input/input5
[ 1.884458] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:01.2/0000:01:00.0/0000:02:08.0/0000:0a:00.1/usb1/1-1/1-1:1.1/0003:046D:C52B.0004/input/input6
[ 1.944095] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:01.2/0000:01:00.0/0000:02:08.0/0000:0a:00.1/usb1/1-1/1-1:1.1/0003:046D:C52B.0004/input/input7
[ 1.944189] hid-generic 0003:046D:C52B.0004: input,hiddev0,hidraw3: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:0a:00.1-1/input1
[ 1.944328] hid-generic 0003:046D:C52B.0005: hiddev1,hidraw4: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:0a:00.1-1/input2
[ 2.051129] scsi 9:0:0:0: Direct-Access Canon MG5100 series 0104 PQ: 0 ANSI: 2
[ 2.051342] sd 9:0:0:0: Attached scsi generic sg4 type 0
[ 2.052198] sd 9:0:0:0: Power-on or device reset occurred
[ 2.053042] sd 9:0:0:0: [sdd] Media removed, stopped polling
[ 2.054072] sd 9:0:0:0: [sdd] Attached SCSI removable disk
[ 2.144465] logitech-djreceiver 0003:046D:C52B.0005: hiddev0,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:0a:00.1-1/input2
[ 2.266170] input: Logitech Wireless Device PID:4051 Mouse as /devices/pci0000:00/0000:00:01.2/0000:01:00.0/0000:02:08.0/0000:0a:00.1/usb1/1-1/1-1:1.2/0003:046D:C52B.0005/0003:046D:4051.0006/input/input9
[ 2.266314] hid-generic 0003:046D:4051.0006: input,hidraw3: USB HID v1.11 Mouse [Logitech Wireless Device PID:4051] on usb-0000:0a:00.1-1/input2:1
[ 2.324393] input: Logitech M510 as /devices/pci0000:00/0000:00:01.2/0000:01:00.0/0000:02:08.0/0000:0a:00.1/usb1/1-1/1-1:1.2/0003:046D:C52B.0005/0003:046D:4051.0006/input/input13
[ 2.324515] logitech-hidpp-device 0003:046D:4051.0006: input,hidraw3: USB HID v1.11 Mouse [Logitech M510] on usb-0000:0a:00.1-1/input2:1
[ 2.754423] scsi 10:0:0:0: Direct-Access Generic STORAGE DEVICE 9744 PQ: 0 ANSI: 0
[ 2.755151] scsi 10:0:0:1: Direct-Access Generic STORAGE DEVICE 9744 PQ: 0 ANSI: 0
[ 2.755768] scsi 10:0:0:2: Direct-Access Generic STORAGE DEVICE 9744 PQ: 0 ANSI: 0
[ 2.756432] scsi 10:0:0:3: Direct-Access Generic STORAGE DEVICE 9744 PQ: 0 ANSI: 0
[ 2.757039] scsi 10:0:0:4: Direct-Access Generic STORAGE DEVICE 9744 PQ: 0 ANSI: 0
[ 2.757328] sd 10:0:0:0: Attached scsi generic sg5 type 0
[ 2.757451] sd 10:0:0:1: Attached scsi generic sg6 type 0
[ 2.757562] sd 10:0:0:2: Attached scsi generic sg7 type 0
[ 2.757762] sd 10:0:0:3: Attached scsi generic sg8 type 0
[ 2.757770] sd 10:0:0:0: [sde] Media removed, stopped polling
[ 2.758176] sd 10:0:0:1: [sdf] Media removed, stopped polling
[ 2.758572] sd 10:0:0:2: [sdg] Media removed, stopped polling
[ 2.758937] sd 10:0:0:4: Attached scsi generic sg9 type 0
[ 2.758944] sd 10:0:0:3: [sdh] Media removed, stopped polling
[ 2.759419] sd 10:0:0:4: [sdi] Media removed, stopped polling
[ 2.761001] sd 10:0:0:0: [sde] Attached SCSI removable disk
[ 2.761757] sd 10:0:0:1: [sdf] Attached SCSI removable disk
[ 2.762500] sd 10:0:0:2: [sdg] Attached SCSI removable disk
[ 2.765871] sd 10:0:0:4: [sdi] Attached SCSI removable disk
[ 2.766254] sd 10:0:0:3: [sdh] Attached SCSI removable disk
[ 3.152490] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.160383] ata1.00: configured for UDMA/100
[ 5.068007] raid6: avx2x4 gen() 35926 MB/s
[ 5.136008] raid6: avx2x2 gen() 40373 MB/s
[ 5.204021] raid6: avx2x1 gen() 30941 MB/s
[ 5.204021] raid6: using algorithm avx2x2 gen() 40373 MB/s
[ 5.272008] raid6: .... xor() 24482 MB/s, rmw enabled
[ 5.272008] raid6: using avx2x2 recovery algorithm
[ 5.272834] xor: automatically using best checksumming function avx
[ 5.305651] Btrfs loaded, crc32c=crc32c-intel, zoned=yes, fsverity=yes
[ 5.496287] EXT4-fs (sdb4): mounted filesystem with ordered data mode. Quota mode: none.
[ 5.653790] systemd[1]: Inserted module 'autofs4'
[ 5.670992] systemd[1]: systemd 245.4-4ubuntu3.17 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[ 5.688035] systemd[1]: Detected architecture x86-64.
[ 5.728631] systemd[1]: Set hostname to <Nico>.
[ 6.913977] systemd[1]: Binding to IPv6 address not available since kernel does not support IPv6.
[ 6.913983] systemd[1]: Binding to IPv6 address not available since kernel does not support IPv6.
[ 6.949008] systemd[1]: Created slice system-modprobe.slice.
[ 6.949202] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 6.949366] systemd[1]: Created slice User and Session Slice.
[ 6.949393] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 6.949475] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 6.949500] systemd[1]: Reached target NFS client services.
[ 6.949511] systemd[1]: Reached target User and Group Name Lookups.
[ 6.949520] systemd[1]: Reached target Slices.
[ 6.949562] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 6.949603] systemd[1]: Listening on LVM2 poll daemon socket.
[ 6.951001] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 6.951111] systemd[1]: Listening on Syslog Socket.
[ 6.951196] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 6.951243] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 6.951389] systemd[1]: Listening on Journal Audit Socket.
[ 6.951463] systemd[1]: Listening on Journal Socket (/dev/log).
[ 6.951543] systemd[1]: Listening on Journal Socket.
[ 6.951621] systemd[1]: Listening on udev Control Socket.
[ 6.951683] systemd[1]: Listening on udev Kernel Socket.
[ 6.952553] systemd[1]: Mounting Huge Pages File System...
[ 6.953446] systemd[1]: Mounting POSIX Message Queue File System...
[ 6.954286] systemd[1]: Mounting NFSD configuration filesystem...
[ 6.955084] systemd[1]: Mounting Kernel Debug File System...
[ 6.955883] systemd[1]: Mounting Kernel Trace File System...
[ 6.957005] systemd[1]: Starting Journal Service...
[ 6.957882] systemd[1]: Starting Availability of block devices...
[ 6.958807] systemd[1]: Starting Set the console keyboard layout...
[ 6.959578] systemd[1]: Starting Create list of static device nodes for the current kernel...
[ 6.960350] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[ 6.961026] systemd[1]: Starting Load Kernel Module drm...
[ 6.962340] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 6.962358] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 6.963264] systemd[1]: Starting Load Kernel Modules...
[ 6.963776] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 6.964266] systemd[1]: Starting udev Coldplug all Devices...
[ 6.964787] systemd[1]: Starting Uncomplicated firewall...
[ 6.965613] systemd[1]: Mounted Huge Pages File System.
[ 6.965706] systemd[1]: Mounted POSIX Message Queue File System.
[ 6.965781] systemd[1]: Mounted Kernel Debug File System.
[ 6.965853] systemd[1]: Mounted Kernel Trace File System.
[ 6.966161] systemd[1]: Finished Availability of block devices.
[ 6.966496] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ 6.970847] EXT4-fs (sdb4): re-mounted. Quota mode: none.
[ 6.971342] ACPI: bus type drm_connector registered
[ 6.971621] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 6.973167] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 6.973192] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[ 6.974064] systemd[1]: Starting Load/Save Random Seed...
[ 6.975047] systemd[1]: Starting Create System Users...
[ 6.975256] systemd[1]: modprobe@drm.service: Succeeded.
[ 6.975495] systemd[1]: Finished Load Kernel Module drm.
[ 6.977430] bpfilter: Loaded bpfilter_umh pid 506
[ 6.977506] bpfilter: read fail 0
[ 6.977509] fbcon: Taking over console
[ 6.977566] Console: switching to colour frame buffer device 210x65
[ 6.981183] RPC: Registered named UNIX socket transport module.
[ 6.981185] RPC: Registered udp transport module.
[ 6.981185] RPC: Registered tcp transport module.
[ 6.981186] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 6.982864] systemd[1]: Finished Load/Save Random Seed.
[ 6.985248] lp: driver loaded but no devices found
[ 6.987371] ppdev: user-space parallel port driver
[ 6.988213] systemd[1]: Finished Create System Users.
[ 6.988865] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 6.994301] IPMI message handler: version 39.2
[ 6.996350] ipmi device interface
[ 6.998988] systemd[1]: Finished Create Static Device Nodes in /dev.
[ 6.999913] systemd[1]: Starting udev Kernel Device Manager...
[ 7.001625] nct6775: Found NCT6798D or compatible chip at 0x2e:0x290
[ 7.003311] systemd[1]: Finished Load Kernel Modules.
[ 7.003641] systemd[1]: Finished Set the console keyboard layout.
[ 7.004302] systemd[1]: Mounting FUSE Control File System...
[ 7.004883] systemd[1]: Mounting Kernel Configuration File System...
[ 7.005481] systemd[1]: Starting Apply Kernel Variables...
[ 7.006275] systemd[1]: Mounted FUSE Control File System.
[ 7.006354] systemd[1]: Mounted Kernel Configuration File System.
[ 7.014073] systemd[1]: Started Journal Service.
[ 7.017272] systemd-journald[480]: Received client request to flush runtime journal.
[ 7.022087] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 7.115044] bpfilter: Loaded bpfilter_umh pid 592
[ 7.115131] bpfilter: read fail 0
[ 7.151937] ccp 0000:0f:00.1: enabling device (0000 -> 0002)
[ 7.154680] ccp 0000:0f:00.1: ccp: unable to access the device: you might be running a broken BIOS.
[ 7.210210] pstore: Using crash dump compression: deflate
[ 7.210216] pstore: Registered efi as persistent store backend
[ 7.211260] usblp 3-4:1.1: usblp1: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x04A9 pid 0x1748
[ 7.211281] usbcore: registered new interface driver usblp
[ 7.248497] RAPL PMU: API unit is 2^-32 Joules, 1 fixed counters, 163840 ms ovfl timer
[ 7.248499] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 7.260781] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 7.271278] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 7.278726] bpfilter: Loaded bpfilter_umh pid 876
[ 7.278810] bpfilter: read fail 0
[ 7.289746] SVM: TSC scaling supported
[ 7.289748] kvm: Nested Virtualization enabled
[ 7.289749] SVM: kvm: Nested Paging enabled
[ 7.289750] SEV supported: 509 ASIDs
[ 7.289769] SVM: Virtual VMLOAD VMSAVE supported
[ 7.289769] SVM: Virtual GIF supported
[ 7.289769] SVM: LBR virtualization supported
[ 7.324178] Intel(R) Wireless WiFi driver for Linux
[ 7.324378] iwlwifi 0000:05:00.0: enabling device (0000 -> 0002)
[ 7.326394] MCE: In-kernel MCE decoding enabled.
[ 7.330864] iwlwifi 0000:05:00.0: Direct firmware load for iwlwifi-cc-a0-72.ucode failed with error -2
[ 7.331217] iwlwifi 0000:05:00.0: Direct firmware load for iwlwifi-cc-a0-71.ucode failed with error -2
[ 7.331799] iwlwifi 0000:05:00.0: Direct firmware load for iwlwifi-cc-a0-70.ucode failed with error -2
[ 7.332022] iwlwifi 0000:05:00.0: Direct firmware load for iwlwifi-cc-a0-69.ucode failed with error -2
[ 7.332032] iwlwifi 0000:05:00.0: Direct firmware load for iwlwifi-cc-a0-68.ucode failed with error -2
[ 7.332042] iwlwifi 0000:05:00.0: Direct firmware load for iwlwifi-cc-a0-67.ucode failed with error -2
[ 7.335555] iwlwifi 0000:05:00.0: api flags index 2 larger than supported by driver
[ 7.335567] iwlwifi 0000:05:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 89.3.35.37
[ 7.335813] iwlwifi 0000:05:00.0: loaded firmware version 66.f1c864e0.0 cc-a0-66.ucode op_mode iwlmvm
[ 7.416080] Adding 18431996k swap on /dev/sdb5. Priority:-2 extents:1 across:18431996k SSFS
[ 7.421243] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none.
[ 7.437028] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Quota mode: none.
[ 7.469346] bpfilter: Loaded bpfilter_umh pid 1088
[ 7.469431] bpfilter: read fail 0
[ 7.469823] EXT4-fs (sdb6): mounted filesystem with ordered data mode. Quota mode: none.
[ 7.478077] intel_rapl_common: Found RAPL domain package
[ 7.478080] intel_rapl_common: Found RAPL domain core
[ 7.482422] snd_hda_intel 0000:0d:00.1: enabling device (0000 -> 0002)
[ 7.482491] snd_hda_intel 0000:0d:00.1: Disabling MSI
[ 7.482499] snd_hda_intel 0000:0d:00.1: Handle vga_switcheroo audio client
[ 7.482568] snd_hda_intel 0000:0f:00.4: enabling device (0000 -> 0002)
[ 7.493524] iwlwifi 0000:05:00.0: Detected Intel(R) Wi-Fi 6 AX200 160MHz, REV=0x340
[ 7.493563] thermal thermal_zone0: failed to read out thermal zone (-61)
[ 7.499967] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.1/0000:0d:00.1/sound/card0/input14
[ 7.500005] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.1/0000:0d:00.1/sound/card0/input15
[ 7.500046] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.1/0000:0d:00.1/sound/card0/input16
[ 7.500077] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.1/0000:0d:00.1/sound/card0/input17
[ 7.500107] input: HDA NVidia HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:03.1/0000:0d:00.1/sound/card0/input18
[ 7.500157] input: HDA NVidia HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:03.1/0000:0d:00.1/sound/card0/input19
[ 7.502991] iwlwifi 0000:05:00.0: reporting RF_KILL (radio disabled)
[ 7.503863] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC1220: line_outs=3 (0x14/0x15/0x16/0x0/0x0) type:line
[ 7.503868] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 7.503870] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 7.503871] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 7.503872] snd_hda_codec_realtek hdaudioC1D0: dig-out=0x1e/0x0
[ 7.503872] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 7.503873] snd_hda_codec_realtek hdaudioC1D0: Front Mic=0x19
[ 7.503879] snd_hda_codec_realtek hdaudioC1D0: Rear Mic=0x18
[ 7.503880] snd_hda_codec_realtek hdaudioC1D0: Line=0x1a
[ 7.507211] audit: type=1400 audit(1653645264.590:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="firejail-default" pid=1120 comm="apparmor_parser"
[ 7.514839] audit: type=1400 audit(1653645264.598:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=1123 comm="apparmor_parser"
[ 7.514844] audit: type=1400 audit(1653645264.598:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=1119 comm="apparmor_parser"
[ 7.514885] audit: type=1400 audit(1653645264.598:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=1124 comm="apparmor_parser"
[ 7.514887] audit: type=1400 audit(1653645264.598:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=1124 comm="apparmor_parser"
[ 7.514902] audit: type=1400 audit(1653645264.598:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=1122 comm="apparmor_parser"
[ 7.514986] audit: type=1400 audit(1653645264.598:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=1116 comm="apparmor_parser"
[ 7.515244] audit: type=1400 audit(1653645264.598:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=1121 comm="apparmor_parser"
[ 7.515247] audit: type=1400 audit(1653645264.598:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=1121 comm="apparmor_parser"
[ 7.515253] audit: type=1400 audit(1653645264.598:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=1121 comm="apparmor_parser"
[ 7.616559] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card1/input20
[ 7.616616] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card1/input21
[ 7.616668] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card1/input22
[ 7.616716] input: HD-Audio Generic Line Out Front as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card1/input23
[ 7.616783] input: HD-Audio Generic Line Out Surround as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card1/input24
[ 7.616860] input: HD-Audio Generic Line Out CLFE as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card1/input25
[ 7.616919] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card1/input26
[ 7.618844] iwlwifi 0000:05:00.0: Detected RF HR B3, rfid=0x10a100
[ 7.658410] bpfilter: Loaded bpfilter_umh pid 1212
[ 7.658471] bpfilter: read fail 0
[ 7.683114] iwlwifi 0000:05:00.0: base HW address: dc:fb:48:02:da:96
[ 7.699892] iwlwifi 0000:05:00.0 wlp5s0: renamed from wlan0
[ 7.764615] bpfilter: Loaded bpfilter_umh pid 1349
[ 7.764692] bpfilter: read fail 0
[ 7.900544] bpfilter: Loaded bpfilter_umh pid 1422
[ 7.900604] bpfilter: read fail 0
[ 8.028667] bpfilter: Loaded bpfilter_umh pid 1425
[ 8.028801] bpfilter: read fail 0
[ 8.132141] bpfilter: Loaded bpfilter_umh pid 1429
[ 8.132267] bpfilter: read fail 0
[ 8.233900] bpfilter: Loaded bpfilter_umh pid 1431
[ 8.234011] bpfilter: read fail 0
[ 8.292519] nvidia-gpu 0000:0d:00.3: i2c timeout error e0000000
[ 8.292542] ucsi_ccg 0-0008: i2c_transfer failed -110
[ 8.292557] ucsi_ccg 0-0008: ucsi_ccg_init failed - -110
[ 8.292574] ucsi_ccg: probe of 0-0008 failed with error -110
[ 8.313543] bpfilter: Loaded bpfilter_umh pid 1433
[ 8.313663] bpfilter: read fail 0
[ 8.395136] bpfilter: Loaded bpfilter_umh pid 1436
[ 8.395265] bpfilter: read fail 0
[ 8.515063] bpfilter: Loaded bpfilter_umh pid 1438
[ 8.515171] bpfilter: read fail 0
[ 8.615463] bpfilter: Loaded bpfilter_umh pid 1440
[ 8.615548] bpfilter: read fail 0
[ 8.675017] bpfilter: Loaded bpfilter_umh pid 1442
[ 8.675125] bpfilter: read fail 0
[ 8.700055] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 8.707808] ata1.00: configured for UDMA/100
[ 8.770690] bpfilter: Loaded bpfilter_umh pid 1448
[ 8.770783] bpfilter: read fail 0
[ 8.888456] bpfilter: Loaded bpfilter_umh pid 1457
[ 8.888570] bpfilter: read fail 0
[ 9.005849] bpfilter: Loaded bpfilter_umh pid 1466
[ 9.005955] bpfilter: read fail 0
[ 9.082609] bpfilter: Loaded bpfilter_umh pid 1468
[ 9.082661] bpfilter: read fail 0
[ 9.151021] bpfilter: Loaded bpfilter_umh pid 1470
[ 9.151129] bpfilter: read fail 0
[ 9.201861] bpfilter: Loaded bpfilter_umh pid 1472
[ 9.201980] bpfilter: read fail 0
[ 9.278710] bpfilter: Loaded bpfilter_umh pid 1474
[ 9.278813] bpfilter: read fail 0
[ 9.338527] bpfilter: Loaded bpfilter_umh pid 1476
[ 9.338646] bpfilter: read fail 0
[ 9.415544] bpfilter: Loaded bpfilter_umh pid 1479
[ 9.415668] bpfilter: read fail 0
[ 9.495135] bpfilter: Loaded bpfilter_umh pid 1481
[ 9.495249] bpfilter: read fail 0
[ 9.552576] bpfilter: Loaded bpfilter_umh pid 1485
[ 9.552710] bpfilter: read fail 0
[ 9.618862] bpfilter: Loaded bpfilter_umh pid 1487
[ 9.618964] bpfilter: read fail 0
[ 9.699150] bpfilter: Loaded bpfilter_umh pid 1489
[ 9.699284] bpfilter: read fail 0
[ 9.775465] bpfilter: Loaded bpfilter_umh pid 1491
[ 9.775605] bpfilter: read fail 0
[ 9.872004] bpfilter: Loaded bpfilter_umh pid 1495
[ 9.872138] bpfilter: read fail 0
[ 9.938042] bpfilter: Loaded bpfilter_umh pid 1497
[ 9.938120] bpfilter: read fail 0
[ 10.003803] bpfilter: Loaded bpfilter_umh pid 1501
[ 10.003896] bpfilter: read fail 0
[ 10.066965] bpfilter: Loaded bpfilter_umh pid 1503
[ 10.067087] bpfilter: read fail 0
[ 10.145959] bpfilter: Loaded bpfilter_umh pid 1505
[ 10.146077] bpfilter: read fail 0
[ 10.218847] bpfilter: Loaded bpfilter_umh pid 1507
[ 10.218940] bpfilter: read fail 0
[ 10.282862] bpfilter: Loaded bpfilter_umh pid 1510
[ 10.282994] bpfilter: read fail 0
[ 10.333736] bpfilter: Loaded bpfilter_umh pid 1512
[ 10.333827] bpfilter: read fail 0
[ 10.393968] bpfilter: Loaded bpfilter_umh pid 1514
[ 10.394084] bpfilter: read fail 0
[ 10.449779] bpfilter: Loaded bpfilter_umh pid 1516
[ 10.449896] bpfilter: read fail 0
[ 10.510983] bpfilter: Loaded bpfilter_umh pid 1518
[ 10.511100] bpfilter: read fail 0
[ 10.557068] e1000e 0000:09:00.0 enp9s0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 10.585854] bpfilter: Loaded bpfilter_umh pid 1520
[ 10.585971] bpfilter: read fail 0
[ 10.648649] igb 0000:07:00.0 enp7s0: igb: enp7s0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 10.658541] bpfilter: Loaded bpfilter_umh pid 1522
[ 10.658653] bpfilter: read fail 0
[ 10.750613] bpfilter: Loaded bpfilter_umh pid 1546
[ 10.750725] bpfilter: read fail 0
[ 10.818775] bpfilter: Loaded bpfilter_umh pid 1548
[ 10.818884] bpfilter: read fail 0
[ 10.902775] bpfilter: Loaded bpfilter_umh pid 1550
[ 10.902881] bpfilter: read fail 0
[ 10.969802] bpfilter: Loaded bpfilter_umh pid 1552
[ 10.969913] bpfilter: read fail 0
[ 11.070664] bpfilter: Loaded bpfilter_umh pid 1555
[ 11.070770] bpfilter: read fail 0
[ 11.174024] bpfilter: Loaded bpfilter_umh pid 1557
[ 11.174114] bpfilter: read fail 0
[ 11.242653] bpfilter: Loaded bpfilter_umh pid 1559
[ 11.242744] bpfilter: read fail 0
[ 11.302511] bpfilter: Loaded bpfilter_umh pid 1561
[ 11.302593] bpfilter: read fail 0
[ 11.362544] bpfilter: Loaded bpfilter_umh pid 1563
[ 11.362610] bpfilter: read fail 0
[ 11.422852] bpfilter: Loaded bpfilter_umh pid 1565
[ 11.422918] bpfilter: read fail 0
[ 11.474058] bpfilter: Loaded bpfilter_umh pid 1567
[ 11.474095] bpfilter: read fail 0
[ 11.536457] bpfilter: Loaded bpfilter_umh pid 1570
[ 11.536493] bpfilter: read fail 0
[ 11.599814] bpfilter: Loaded bpfilter_umh pid 1573
[ 11.599862] bpfilter: read fail 0
[ 11.657774] bpfilter: Loaded bpfilter_umh pid 1575
[ 11.657813] bpfilter: read fail 0
[ 11.730082] bpfilter: Loaded bpfilter_umh pid 1582
[ 11.730134] bpfilter: read fail 0
[ 11.791920] bpfilter: Loaded bpfilter_umh pid 1585
[ 11.791958] bpfilter: read fail 0
[ 11.853820] bpfilter: Loaded bpfilter_umh pid 1587
[ 11.853863] bpfilter: read fail 0
[ 11.919750] bpfilter: Loaded bpfilter_umh pid 1590
[ 11.919856] bpfilter: read fail 0
[ 11.986683] bpfilter: Loaded bpfilter_umh pid 1592
[ 11.986758] bpfilter: read fail 0
[ 12.066748] bpfilter: Loaded bpfilter_umh pid 1594
[ 12.066815] bpfilter: read fail 0
[ 12.158992] bpfilter: Loaded bpfilter_umh pid 1596
[ 12.159059] bpfilter: read fail 0
[ 12.210564] bpfilter: Loaded bpfilter_umh pid 1598
[ 12.210641] bpfilter: read fail 0
[ 12.262167] bpfilter: Loaded bpfilter_umh pid 1600
[ 12.262251] bpfilter: read fail 0
[ 12.334564] bpfilter: Loaded bpfilter_umh pid 1602
[ 12.334647] bpfilter: read fail 0
[ 12.390217] bpfilter: Loaded bpfilter_umh pid 1604
[ 12.390300] bpfilter: read fail 0
[ 12.442604] bpfilter: Loaded bpfilter_umh pid 1606
[ 12.442689] bpfilter: read fail 0
[ 12.500002] bpfilter: Loaded bpfilter_umh pid 1609
[ 12.500138] bpfilter: read fail 0
[ 12.593538] bpfilter: Loaded bpfilter_umh pid 1636
[ 12.593606] bpfilter: read fail 0
[ 12.664615] usblp1: removed
[ 12.670374] usblp 3-4:1.1: usblp1: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x04A9 pid 0x1748
[ 12.694295] bpfilter: Loaded bpfilter_umh pid 1669
[ 12.694365] bpfilter: read fail 0
[ 12.766491] bpfilter: Loaded bpfilter_umh pid 1671
[ 12.766589] bpfilter: read fail 0
[ 12.862961] bpfilter: Loaded bpfilter_umh pid 1673
[ 12.863070] bpfilter: read fail 0
[ 12.943158] bpfilter: Loaded bpfilter_umh pid 1675
[ 12.943281] bpfilter: read fail 0
[ 13.023787] bpfilter: Loaded bpfilter_umh pid 1678
[ 13.023892] bpfilter: read fail 0
[ 13.082757] bpfilter: Loaded bpfilter_umh pid 1680
[ 13.082860] bpfilter: read fail 0
[ 13.143215] bpfilter: Loaded bpfilter_umh pid 1682
[ 13.143325] bpfilter: read fail 0
[ 13.204468] bpfilter: Loaded bpfilter_umh pid 1685
[ 13.204593] bpfilter: read fail 0
[ 13.271067] bpfilter: Loaded bpfilter_umh pid 1687
[ 13.271150] bpfilter: read fail 0
[ 13.334903] bpfilter: Loaded bpfilter_umh pid 1689
[ 13.335010] bpfilter: read fail 0
[ 13.394908] bpfilter: Loaded bpfilter_umh pid 1691
[ 13.395018] bpfilter: read fail 0
[ 13.458946] bpfilter: Loaded bpfilter_umh pid 1693
[ 13.459046] bpfilter: read fail 0
[ 13.522932] bpfilter: Loaded bpfilter_umh pid 1695
[ 13.523031] bpfilter: read fail 0
[ 13.586901] bpfilter: Loaded bpfilter_umh pid 1699
[ 13.587024] bpfilter: read fail 0
[ 13.650980] bpfilter: Loaded bpfilter_umh pid 1703
[ 13.651082] bpfilter: read fail 0
[ 13.706786] bpfilter: Loaded bpfilter_umh pid 1705
[ 13.706901] bpfilter: read fail 0
[ 13.762944] bpfilter: Loaded bpfilter_umh pid 1707
[ 13.763060] bpfilter: read fail 0
[ 13.830774] bpfilter: Loaded bpfilter_umh pid 1709
[ 13.830886] bpfilter: read fail 0
[ 13.892982] bpfilter: Loaded bpfilter_umh pid 1712
[ 13.893092] bpfilter: read fail 0
[ 13.980445] bpfilter: Loaded bpfilter_umh pid 1715
[ 13.980564] bpfilter: read fail 0
[ 14.063082] bpfilter: Loaded bpfilter_umh pid 1717
[ 14.063194] bpfilter: read fail 0
[ 14.151907] bpfilter: Loaded bpfilter_umh pid 1721
[ 14.152034] bpfilter: read fail 0
[ 14.226951] bpfilter: Loaded bpfilter_umh pid 1723
[ 14.227065] bpfilter: read fail 0
[ 14.279178] bpfilter: Loaded bpfilter_umh pid 1725
[ 14.279299] bpfilter: read fail 0
[ 14.335027] bpfilter: Loaded bpfilter_umh pid 1727
[ 14.335138] bpfilter: read fail 0
[ 14.407817] bpfilter: Loaded bpfilter_umh pid 1731
[ 14.407934] bpfilter: read fail 0
[ 14.491016] bpfilter: Loaded bpfilter_umh pid 1733
[ 14.491122] bpfilter: read fail 0
[ 14.563165] bpfilter: Loaded bpfilter_umh pid 1735
[ 14.563283] bpfilter: read fail 0
[ 14.639158] bpfilter: Loaded bpfilter_umh pid 1737
[ 14.639274] bpfilter: read fail 0
[ 14.786836] kauditd_printk_skb: 14 callbacks suppressed
[ 14.786840] audit: type=1400 audit(1653645271.870:26): apparmor="DENIED" operation="capable" profile="/usr/sbin/cups-browsed" pid=1860 comm="cups-browsed" capability=23 capname="sys_nice"
[ 15.816948] NFSD: Using UMH upcall client tracking operations.
[ 15.816952] NFSD: starting 90-second grace period (net f0000000)
[ 33.718353] logitech-hidpp-device 0003:046D:4051.0006: HID++ 4.5 device connected.
[ 84.595104] [UFW BLOCK] IN=enp9s0 OUT= MAC=01:00:5e:00:00:01:dc:15:c8:b6:c8:fe:08:00 SRC=192.168.178.1 DST=224.0.0.1 LEN=36 TOS=0x00 PREC=0xC0 TTL=1 ID=19442 DF PROTO=2
[ 114.231147] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 114.233528] ISO 9660 Extensions: IEEE_1282
[ 133.535017] ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
[ 133.535024] ata1.00: irq_stat 0x00000040, connection status changed
[ 133.535025] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 133.535028] ata1.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 15 dma 131072 in
Read(10) 28 00 00 00 13 19 00 00 40 00res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[ 133.535033] ata1.00: status: { DRDY }
[ 133.535037] ata1: hard resetting link
[ 134.418991] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 134.426501] ata1.00: configured for UDMA/100
[ 134.427110] sr 0:0:0:0: [sr0] tag#15 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[ 134.427113] sr 0:0:0:0: [sr0] tag#15 Sense Key : Illegal Request [current]
[ 134.427114] sr 0:0:0:0: [sr0] tag#15 Add. Sense: Unaligned write command
[ 134.427116] sr 0:0:0:0: [sr0] tag#15 CDB: Read(10) 28 00 00 00 13 19 00 00 40 00
[ 134.427117] I/O error, dev sr0, sector 19556 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 134.427126] ata1: EH complete
[ 134.554987] ata1.00: limiting speed to UDMA/66:PIO4
[ 134.554991] ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
[ 134.554994] ata1.00: irq_stat 0x00000040, connection status changed
[ 134.554995] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 134.554999] ata1.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 11 dma 4096 in
Read(10) 28 00 00 00 13 4f 00 00 02 00res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[ 134.555003] ata1.00: status: { DRDY }
[ 134.555007] ata1: hard resetting link
[ 135.431012] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 135.438461] ata1.00: configured for UDMA/66
[ 135.439068] ata1: EH complete
[ 141.175204] ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
[ 141.175210] ata1.00: irq_stat 0x00000040, connection status changed
[ 141.175212] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 141.175216] ata1.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 22 dma 131072 in
Read(10) 28 00 00 00 1e 19 00 00 40 00res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[ 141.175221] ata1.00: status: { DRDY }
[ 141.175224] ata1: hard resetting link
[ 142.051228] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 142.058737] ata1.00: configured for UDMA/66
[ 142.059285] sr 0:0:0:0: [sr0] tag#22 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[ 142.059288] sr 0:0:0:0: [sr0] tag#22 Sense Key : Illegal Request [current]
[ 142.059290] sr 0:0:0:0: [sr0] tag#22 Add. Sense: Unaligned write command
[ 142.059291] sr 0:0:0:0: [sr0] tag#22 CDB: Read(10) 28 00 00 00 1e 19 00 00 40 00
[ 142.059292] I/O error, dev sr0, sector 30820 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 142.059304] ata1: EH complete
[ 145.187308] ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
[ 145.187317] ata1.00: irq_stat 0x00000040, connection status changed
[ 145.187319] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 145.187324] ata1.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 19 dma 131072 in
Read(10) 28 00 00 00 2b 19 00 00 40 00res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[ 145.187330] ata1.00: status: { DRDY }
[ 145.187334] ata1: hard resetting link
[ 146.071327] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 146.078793] ata1.00: configured for UDMA/66
[ 146.079403] sr 0:0:0:0: [sr0] tag#19 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[ 146.079406] sr 0:0:0:0: [sr0] tag#19 Sense Key : Illegal Request [current]
[ 146.079408] sr 0:0:0:0: [sr0] tag#19 Add. Sense: Unaligned write command
[ 146.079410] sr 0:0:0:0: [sr0] tag#19 CDB: Read(10) 28 00 00 00 2b 19 00 00 40 00
[ 146.079411] I/O error, dev sr0, sector 44132 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 146.079421] ata1: EH complete
[ 146.175330] ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
[ 146.175339] ata1.00: irq_stat 0x00000040, connection status changed
[ 146.175341] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 146.175346] ata1.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 5 dma 4096 in
Read(10) 28 00 00 00 2b 51 00 00 02 00res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[ 146.175351] ata1.00: status: { DRDY }
[ 146.175356] ata1: hard resetting link
[ 147.059350] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 147.066798] ata1.00: configured for UDMA/66
[ 147.067405] ata1: EH complete
[ 148.087377] ata1.00: limiting speed to UDMA/33:PIO4
[ 148.087382] ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
[ 148.087386] ata1.00: irq_stat 0x00000040, connection status changed
[ 148.087387] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 148.087392] ata1.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 12 dma 131072 in
Read(10) 28 00 00 00 33 19 00 00 40 00res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[ 148.087397] ata1.00: status: { DRDY }
[ 148.087401] ata1: hard resetting link
[ 148.963385] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 148.970874] ata1.00: configured for UDMA/33
[ 148.971490] sr 0:0:0:0: [sr0] tag#12 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[ 148.971493] sr 0:0:0:0: [sr0] tag#12 Sense Key : Illegal Request [current]
[ 148.971496] sr 0:0:0:0: [sr0] tag#12 Add. Sense: Unaligned write command
[ 148.971498] sr 0:0:0:0: [sr0] tag#12 CDB: Read(10) 28 00 00 00 33 19 00 00 40 00
[ 148.971499] I/O error, dev sr0, sector 52324 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 148.971518] ata1: EH complete
[ 150.979412] ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
[ 150.979419] ata1.00: irq_stat 0x00000040, connection status changed
[ 150.979420] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 150.979425] ata1.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 23 dma 131072 in
Read(10) 28 00 00 00 3d 59 00 00 40 00res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[ 150.979429] ata1.00: status: { DRDY }
[ 150.979433] ata1: hard resetting link
[ 151.863433] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 151.870955] ata1.00: configured for UDMA/33
[ 151.871503] sr 0:0:0:0: [sr0] tag#23 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[ 151.871511] sr 0:0:0:0: [sr0] tag#23 Sense Key : Illegal Request [current]
[ 151.871515] sr 0:0:0:0: [sr0] tag#23 Add. Sense: Unaligned write command
[ 151.871519] sr 0:0:0:0: [sr0] tag#23 CDB: Read(10) 28 00 00 00 3d 59 00 00 40 00
[ 151.871521] I/O error, dev sr0, sector 62820 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 151.871542] ata1: EH complete
[ 151.959434] ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
[ 151.959441] ata1.00: irq_stat 0x00000040, connection status changed
[ 151.959442] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 151.959446] ata1.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 9 dma 4096 in
Read(10) 28 00 00 00 3d 81 00 00 02 00res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[ 151.959451] ata1.00: status: { DRDY }
[ 151.959455] ata1: hard resetting link
[ 152.847442] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 152.854887] ata1.00: configured for UDMA/33
[ 152.855491] ata1: EH complete
[ 209.596696] [UFW BLOCK] IN=enp9s0 OUT= MAC=01:00:5e:00:00:01:dc:15:c8:b6:c8:fe:08:00 SRC=192.168.178.1 DST=224.0.0.1 LEN=36 TOS=0x00 PREC=0xC0 TTL=1 ID=27432 DF PROTO=2
[ 224.807278] [UFW BLOCK] IN=enp9s0 OUT= MAC=68:05:ca:0c:63:13:dc:15:c8:b6:c8:fe:08:00 SRC=192.168.178.1 DST=192.168.178.21 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=50901 DF PROTO=TCP SPT=35577 DPT=80 WINDOW=29200 RES=0x00 SYN URGP=0
[ 225.833160] [UFW BLOCK] IN=enp9s0 OUT= MAC=68:05:ca:0c:63:13:dc:15:c8:b6:c8:fe:08:00 SRC=192.168.178.1 DST=192.168.178.21 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=50902 DF PROTO=TCP SPT=35577 DPT=80 WINDOW=29200 RES=0x00 SYN URGP=0
[ 227.848994] [UFW BLOCK] IN=enp9s0 OUT= MAC=68:05:ca:0c:63:13:dc:15:c8:b6:c8:fe:08:00 SRC=192.168.178.1 DST=192.168.178.21 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=50903 DF PROTO=TCP SPT=35577 DPT=80 WINDOW=29200 RES=0x00 SYN URGP=0
[ 232.073210] [UFW BLOCK] IN=enp9s0 OUT= MAC=68:05:ca:0c:63:13:dc:15:c8:b6:c8:fe:08:00 SRC=192.168.178.1 DST=192.168.178.21 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=50904 DF PROTO=TCP SPT=35577 DPT=80 WINDOW=29200 RES=0x00 SYN URGP=0
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-05-27 10:32 ` J.J. Berkhout
@ 2022-08-05 9:17 ` J.J. Berkhout
2022-09-20 10:05 ` J.J. Berkhout
0 siblings, 1 reply; 20+ messages in thread
From: J.J. Berkhout @ 2022-08-05 9:17 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 2265 bytes --]
Hello,
This morning I tried the 5.19 kernel from
https://kernel.ubuntu.com/~kernel-ppa/mainline/?C=N;O=D
The result regarding the problem with my optical drive still exists.
With kind regards,
Jaap Berkhout.
On 27-05-2022 12:32, J.J. Berkhout wrote:
> Hello,
>
> On 27-05-2022 01:36, Damien Le Moal wrote:
>> On 2022/05/26 21:38, J.J. Berkhout wrote:
> .
> .
>>> The problem is:
>>> After going from Linux Mint 19.3 Cinnamon kernel 5.4.0-97 to Linux Mint
>>> 20.3 Cinnamon kernel 5.4.0-107 I discovered that I could not (reliably)
>>> access my optical drive anymore.
>>> It produces errors like:
>>> ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
>>> ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
>>> ata1.00: cmd a0/00:00:00:00:fc/00:00:00:00:00/a0 tag 0 pio 131072 in
>>> Read(10) 28 00 00 00 05 61 00 00 40 00res
>>> 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
>>> blk_update_request: I/O error, dev sr0, sector 5508 op 0x0:(READ) flags
>>> 0x80700 phys_seg 19 prio class 0
>>> ata1.00: failed to set xfermode (err_mask=0x1)
>>>
>>> The system was Linux Mint 20.3 Cinnamon with kernel 5.4.0-107-generic,
>>> mobo ASRock model X570 Taichi.
>>> After some tests I found out:
>>> Kernel 5.4.0-99 works OK;
>>> Kernel 5.4.0-100 has the problem;
>>> Kernel 5.13.0-30 works OK;
>>> Kernel 5.13.0-35 has the problem.
>>
>> It looks like your distro is backporting patches so the patch causing the
>> problem could be found by bisecting. While 5.4 kernel is an LTS kernel, the
>> latest release is 5.4.196... 5.4.0-100 is the distro version number which does
>> not tell me what set of patches it got on top of 5.4.0. These are not
>> stable/vanilla kernels.
>>
>> To get help from this list, you will need to try with a vanilla kernel, ideally
>> from git. You could try the latest mainline 5.18 first to see if the problem is
>> there or not.
>
> OK, I installed kernel 5.18.0 with 'mainline' (Ubuntu Mainline Kernel
> Installer).
> Kernel installed was 5.18.0-051800.202205222030.
> Same problem existed.
> I reverted to the ubuntu 5.13.0-30 kernel.
> A copy of the dmesg output is attached.
>
> With kind regards,
>
> Jaap Berkhout.
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-08-05 9:17 ` J.J. Berkhout
@ 2022-09-20 10:05 ` J.J. Berkhout
2022-09-20 13:06 ` Niklas Cassel
0 siblings, 1 reply; 20+ messages in thread
From: J.J. Berkhout @ 2022-09-20 10:05 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 2666 bytes --]
On 05-08-2022 11:17, J.J. Berkhout wrote:
Hello,
This morning I updated my motherboard (ASRock model X570 Taichi) from
UEFI v. 3.60 to UEFI 4.80. Update went perfectly, but did not solve the
problem with my optical drive. I am at a loss how to proceed next.
Any suggestions?
With kind regards,
Jaap Berkhout
> Hello,
>
> This morning I tried the 5.19 kernel from
> https://kernel.ubuntu.com/~kernel-ppa/mainline/?C=N;O=D
>
> The result regarding the problem with my optical drive still exists.
>
> With kind regards,
>
> Jaap Berkhout.
>
> On 27-05-2022 12:32, J.J. Berkhout wrote:
>> Hello,
>>
>> On 27-05-2022 01:36, Damien Le Moal wrote:
>>> On 2022/05/26 21:38, J.J. Berkhout wrote:
>> .
>> .
>>>> The problem is:
>>>> After going from Linux Mint 19.3 Cinnamon kernel 5.4.0-97 to Linux Mint
>>>> 20.3 Cinnamon kernel 5.4.0-107 I discovered that I could not (reliably)
>>>> access my optical drive anymore.
>>>> It produces errors like:
>>>> ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
>>>> ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
>>>> ata1.00: cmd a0/00:00:00:00:fc/00:00:00:00:00/a0 tag 0 pio 131072 in
>>>> Read(10) 28 00 00 00 05 61 00 00 40 00res
>>>> 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
>>>> blk_update_request: I/O error, dev sr0, sector 5508 op 0x0:(READ) flags
>>>> 0x80700 phys_seg 19 prio class 0
>>>> ata1.00: failed to set xfermode (err_mask=0x1)
>>>>
>>>> The system was Linux Mint 20.3 Cinnamon with kernel 5.4.0-107-generic,
>>>> mobo ASRock model X570 Taichi.
>>>> After some tests I found out:
>>>> Kernel 5.4.0-99 works OK;
>>>> Kernel 5.4.0-100 has the problem;
>>>> Kernel 5.13.0-30 works OK;
>>>> Kernel 5.13.0-35 has the problem.
>>>
>>> It looks like your distro is backporting patches so the patch causing the
>>> problem could be found by bisecting. While 5.4 kernel is an LTS kernel, the
>>> latest release is 5.4.196... 5.4.0-100 is the distro version number which does
>>> not tell me what set of patches it got on top of 5.4.0. These are not
>>> stable/vanilla kernels.
>>>
>>> To get help from this list, you will need to try with a vanilla kernel, ideally
>>> from git. You could try the latest mainline 5.18 first to see if the problem is
>>> there or not.
>>
>> OK, I installed kernel 5.18.0 with 'mainline' (Ubuntu Mainline Kernel
>> Installer).
>> Kernel installed was 5.18.0-051800.202205222030.
>> Same problem existed.
>> I reverted to the ubuntu 5.13.0-30 kernel.
>> A copy of the dmesg output is attached.
>>
>> With kind regards,
>>
>> Jaap Berkhout.
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-20 10:05 ` J.J. Berkhout
@ 2022-09-20 13:06 ` Niklas Cassel
[not found] ` <9756ac37-6790-7b83-5840-abe04f8ab838@staalenberk.nl>
0 siblings, 1 reply; 20+ messages in thread
From: Niklas Cassel @ 2022-09-20 13:06 UTC (permalink / raw)
To: J.J. Berkhout; +Cc: linux-ide
On Tue, Sep 20, 2022 at 12:05:57PM +0200, J.J. Berkhout wrote:
>
>
> On 05-08-2022 11:17, J.J. Berkhout wrote:
>
> Hello,
>
> This morning I updated my motherboard (ASRock model X570 Taichi) from
> UEFI v. 3.60 to UEFI 4.80. Update went perfectly, but did not solve the
> problem with my optical drive. I am at a loss how to proceed next.
> Any suggestions?
>
> With kind regards,
>
> Jaap Berkhout
Hello Jaap,
Looking at the changelog in the -100 ubuntu kernel:
https://git.launchpad.net/~ubuntu-kernel/ubuntu/+source/linux/+git/focal/commit/?h=Ubuntu-5.4.0-100.113&id=529e771269e0d4b5f323c3f8ece3ac9ea6037a62
There are two clear main suspects:
libata: add horkage for ASMedia 1092
and
ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile
When you boot the working kernel (-99)
what is the output of
$ lsscsi
do you see "ASMT109x-" there?
Kind regards,
Niklas
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-05-26 12:38 Multiple errors with DVD drive J.J. Berkhout
2022-05-26 23:36 ` Damien Le Moal
@ 2022-09-20 13:35 ` Niklas Cassel
1 sibling, 0 replies; 20+ messages in thread
From: Niklas Cassel @ 2022-09-20 13:35 UTC (permalink / raw)
To: J.J. Berkhout; +Cc: linux-ide
On Thu, May 26, 2022 at 02:38:53PM +0200, J.J. Berkhout wrote:
> Firstly, if this is not the right place for this message, I apologize.
> In this case, disregard.
>
> I have a problem which I suspect is a bug in libata, but of course I
> could be wrong.
>
> The problem is:
> After going from Linux Mint 19.3 Cinnamon kernel 5.4.0-97 to Linux Mint
> 20.3 Cinnamon kernel 5.4.0-107 I discovered that I could not (reliably)
> access my optical drive anymore.
> It produces errors like:
> ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xe frozen
> ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
> ata1.00: cmd a0/00:00:00:00:fc/00:00:00:00:00/a0 tag 0 pio 131072 in
> Read(10) 28 00 00 00 05 61 00 00 40 00res
> 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
> blk_update_request: I/O error, dev sr0, sector 5508 op 0x0:(READ) flags
> 0x80700 phys_seg 19 prio class 0
> ata1.00: failed to set xfermode (err_mask=0x1)
>
FWIW, there seems to be a bunch of quirks for Pioneer optical drives
related to set xfermode:
/*
* Devices which choke on SETXFER. Applies only if both the
* device and controller are SATA.
*/
{ "PIONEER DVD-RW DVRTD08", NULL, ATA_HORKAGE_NOSETXFER },
{ "PIONEER DVD-RW DVRTD08A", NULL, ATA_HORKAGE_NOSETXFER },
{ "PIONEER DVD-RW DVR-215", NULL, ATA_HORKAGE_NOSETXFER },
{ "PIONEER DVD-RW DVR-212D", NULL, ATA_HORKAGE_NOSETXFER },
{ "PIONEER DVD-RW DVR-216D", NULL, ATA_HORKAGE_NOSETXFER },
Perhaps you could try the following patch:
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 826d41f341e4..263f6a59b2cf 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3987,6 +3987,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "PIONEER DVD-RW DVR-215", NULL, ATA_HORKAGE_NOSETXFER },
{ "PIONEER DVD-RW DVR-212D", NULL, ATA_HORKAGE_NOSETXFER },
{ "PIONEER DVD-RW DVR-216D", NULL, ATA_HORKAGE_NOSETXFER },
+ { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOSETXFER },
/* Crucial BX100 SSD 500GB has broken LPM support */
{ "CT500BX100SSD1", NULL, ATA_HORKAGE_NOLPM },
Kind regards,
Niklas
^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
[not found] ` <9756ac37-6790-7b83-5840-abe04f8ab838@staalenberk.nl>
@ 2022-09-20 21:08 ` Niklas Cassel
2022-09-21 10:28 ` J.J. Berkhout
0 siblings, 1 reply; 20+ messages in thread
From: Niklas Cassel @ 2022-09-20 21:08 UTC (permalink / raw)
To: J.J. Berkhout; +Cc: linux-ide
Readding linux-ide to CC.
On Tue, Sep 20, 2022 at 06:23:07PM +0200, J.J. Berkhout wrote:
> Hello,
>
> Thanks for looking into this.
> I do not see anything like "ASMT109x-".
> Output of lsscsi:
>
> [0:0:0:0] cd/dvd PIONEER BD-RW BDR-207M 1.60 /dev/sr0 [11:0]
Ok, then we can rule out the patch that adds the ASMT109x quirk.
>
> The output with the last non-working kernel is the same.
>
> Concerning the patch: I do not (yet) known how to apply it. Help would
> very much be appreciated.
Basically:
git clone https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
cd linux
Try to copy the running kernel's config:
zcat /proc/config.gz > .config
If that didn't work, try copying the config file from /boot:
cp /boot/config-$(uname -r) .config
Since the patch is only one line, you can apply it manually now.
(Note that there are three spaces between "BD-RW BDR-207M".)
make olddefconfig
make -j$(nproc)
sudo make modules_install
sudo make install
Looking at the logs in the bug report, you do have a AMD Green Sardine
AHCI controller.
The commit 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as
board_ahci_mobile") added the PCI vendor and device id to the list of
supported AHCI controllers using the low power board version:
{ PCI_VDEVICE(AMD, 0x7901), board_ahci_low_power }, /* AMD Green Sardine */
Before the commit in question, your AHCI controller relied on this
catch-all entry:
/* Generic, PCI class code for AHCI */
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff, board_ahci },
which does not enable/allow any low power mode at all.
Now, I do think that low power modes *should* work with this AHCI
controller. Most likely, it is simply the optical drive that does
not work well when the HBA initiates a low power mode on the link.
You should be able to test this theory by adding libata.force=nolpm
on the kernel command line on a recent (non-working) kernel, low power
modes should then be disabled, and the drive should work again.
(You can press 'e' in grub to temporarily add something to the kernel
command line, and then ctrl+x to boot.)
But the proper fix is probably to add a quirk for you device, either:
+ { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOSETXFER },
or
+ { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOLPM },
Kind regards,
Niklas
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-20 21:08 ` Niklas Cassel
@ 2022-09-21 10:28 ` J.J. Berkhout
2022-09-21 11:58 ` Niklas Cassel
0 siblings, 1 reply; 20+ messages in thread
From: J.J. Berkhout @ 2022-09-21 10:28 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 3068 bytes --]
On 20-09-2022 23:08, Niklas Cassel wrote:
> Readding linux-ide to CC.
>
> On Tue, Sep 20, 2022 at 06:23:07PM +0200, J.J. Berkhout wrote:
>> Hello,
>>
>> Thanks for looking into this.
>> I do not see anything like "ASMT109x-".
>> Output of lsscsi:
>>
>> [0:0:0:0] cd/dvd PIONEER BD-RW BDR-207M 1.60 /dev/sr0 [11:0]
>
> Ok, then we can rule out the patch that adds the ASMT109x quirk.
>
>>
>> The output with the last non-working kernel is the same.
>>
>> Concerning the patch: I do not (yet) known how to apply it. Help would
>> very much be appreciated.
>
> Basically:
> git clone https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
> cd linux
>
> Try to copy the running kernel's config:
> zcat /proc/config.gz > .config
>
> If that didn't work, try copying the config file from /boot:
> cp /boot/config-$(uname -r) .config
>
> Since the patch is only one line, you can apply it manually now.
> (Note that there are three spaces between "BD-RW BDR-207M".)
>
> make olddefconfig
> make -j$(nproc)
>
> sudo make modules_install
> sudo make install
>
>
>
> Looking at the logs in the bug report, you do have a AMD Green Sardine
> AHCI controller.
>
> The commit 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as
> board_ahci_mobile") added the PCI vendor and device id to the list of
> supported AHCI controllers using the low power board version:
> { PCI_VDEVICE(AMD, 0x7901), board_ahci_low_power }, /* AMD Green Sardine */
>
> Before the commit in question, your AHCI controller relied on this
> catch-all entry:
> /* Generic, PCI class code for AHCI */
> { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
> PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff, board_ahci },
> which does not enable/allow any low power mode at all.
>
> Now, I do think that low power modes *should* work with this AHCI
> controller. Most likely, it is simply the optical drive that does
> not work well when the HBA initiates a low power mode on the link.
>
> You should be able to test this theory by adding libata.force=nolpm
> on the kernel command line on a recent (non-working) kernel, low power
> modes should then be disabled, and the drive should work again.
> (You can press 'e' in grub to temporarily add something to the kernel
> command line, and then ctrl+x to boot.)
>
> But the proper fix is probably to add a quirk for you device, either:
> + { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOSETXFER },
> or
> + { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOLPM },
>
>
> Kind regards,
> Niklas
I just tested the libata.force=nolpm kernel parameter on my system
running kernel 5.15.0-48-generic x86_64 (linux mint 20.3, base Ubuntu
20.04 focal). I am sorry to say, this parameter did not solve the problem.
As for your patch concerning NOSETXFER, I will try to test this shortly,
but it could take one or two days (medical stuff for me and my wife).
Thanks for your help.
With kind regards,
Jaap Berkhout
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-21 10:28 ` J.J. Berkhout
@ 2022-09-21 11:58 ` Niklas Cassel
2022-09-21 12:38 ` J.J. Berkhout
0 siblings, 1 reply; 20+ messages in thread
From: Niklas Cassel @ 2022-09-21 11:58 UTC (permalink / raw)
To: J.J. Berkhout; +Cc: linux-ide
On Wed, Sep 21, 2022 at 12:28:34PM +0200, J.J. Berkhout wrote:
> On 20-09-2022 23:08, Niklas Cassel wrote:
> >
> > You should be able to test this theory by adding libata.force=nolpm
> > on the kernel command line on a recent (non-working) kernel, low power
> > modes should then be disabled, and the drive should work again.
> > (You can press 'e' in grub to temporarily add something to the kernel
> > command line, and then ctrl+x to boot.)
> >
> > But the proper fix is probably to add a quirk for you device, either:
> > + { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOSETXFER },
> > or
> > + { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOLPM },
>
> I just tested the libata.force=nolpm kernel parameter on my system
> running kernel 5.15.0-48-generic x86_64 (linux mint 20.3, base Ubuntu
> 20.04 focal). I am sorry to say, this parameter did not solve the problem.
Another way do disable lpm is to do:
$ ls -al /sys/class/scsi_host/host*
Find your device in the list. My device is:
/sys/class/scsi_host/host13/
Print the current lpm policy for your device:
$ cat /sys/class/scsi_host/host13/link_power_management_policy
med_power_with_dipm
Anything other than "max_performance" means that you have (a varying degree)
of low power modes enabled.
$ sudo sh -c "echo max_performance > /sys/class/scsi_host/host13/link_power_management_policy"
$ cat /sys/class/scsi_host/host13/link_power_management_policy
max_performance
Try reading from the optical drive after ensuring that the policy is
"max_performance".
However, disabling all low power modes on the kernel command line
should basically be the same.
Perhaps you could verify that your policy is "max_performance" out of the box
when booting the non-working kernel with libata.force=nolpm.
Booting the non-working without libata.force=nolpm should result in
"med_power_with_dipm"
(as that is the ubuntu default).
Booting the old kernel should result in "max_performance", since lpm
wasn't available/allowed for your AHCI controller in your old kernel.
>
> As for your patch concerning NOSETXFER, I will try to test this shortly,
> but it could take one or two days (medical stuff for me and my wife).
There is absolutely no need to rush.
Kind regards,
Niklas
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-21 11:58 ` Niklas Cassel
@ 2022-09-21 12:38 ` J.J. Berkhout
2022-09-21 14:54 ` J.J. Berkhout
` (2 more replies)
0 siblings, 3 replies; 20+ messages in thread
From: J.J. Berkhout @ 2022-09-21 12:38 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 1345 bytes --]
Hello,
On 21-09-2022 13:58, Niklas Cassel wrote:
> Another way do disable lpm is to do:
>
> $ ls -al /sys/class/scsi_host/host*
>
> Find your device in the list. My device is:
> /sys/class/scsi_host/host13/
>
> Print the current lpm policy for your device:
> $ cat /sys/class/scsi_host/host13/link_power_management_policy
> med_power_with_dipm
>
> Anything other than "max_performance" means that you have (a varying degree)
> of low power modes enabled.
>
> $ sudo sh -c "echo max_performance > /sys/class/scsi_host/host13/link_power_management_policy"
>
> $ cat /sys/class/scsi_host/host13/link_power_management_policy
> max_performance
>
> Try reading from the optical drive after ensuring that the policy is
> "max_performance".
>
Yes, this worked and did the trick! Reading without any errors. I did
not yet try to write, but will do so today.
When booting with libata.force=nolpm the link_power_management_policy
was still med_power_with_dipm and I got the dmesg:
[ 0.291452] ata: failed to parse force parameter "nolpm" (unknown value)
so the ineffectiveness of this boot parameter seems to be explained.
Might there be some other syntax for this parameter?
Nevertheless, my problem now has a work-around and I am very happy.
Thanks, Niklas.
Kind regards,
Jaap Berkhout
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-21 12:38 ` J.J. Berkhout
@ 2022-09-21 14:54 ` J.J. Berkhout
2022-09-21 18:32 ` Niklas Cassel
2022-09-22 22:08 ` Damien Le Moal
2 siblings, 0 replies; 20+ messages in thread
From: J.J. Berkhout @ 2022-09-21 14:54 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 1039 bytes --]
Hello,
On 21-09-2022 14:38, J.J. Berkhout wrote:
> On 21-09-2022 13:58, Niklas Cassel wrote:
>> Another way do disable lpm is to do:
>>
>> $ ls -al /sys/class/scsi_host/host*
>>
>> Find your device in the list. My device is:
>> /sys/class/scsi_host/host13/
>>
>> Print the current lpm policy for your device:
>> $ cat /sys/class/scsi_host/host13/link_power_management_policy
>> med_power_with_dipm
>>
>> Anything other than "max_performance" means that you have (a varying degree)
>> of low power modes enabled.
>>
>> $ sudo sh -c "echo max_performance > /sys/class/scsi_host/host13/link_power_management_policy"
>>
>> $ cat /sys/class/scsi_host/host13/link_power_management_policy
>> max_performance
>>
>> Try reading from the optical drive after ensuring that the policy is
>> "max_performance".
>>
>
> Yes, this worked and did the trick! Reading without any errors. I did
> not yet try to write, but will do so today.
I just wrote two Blu-Ray disks without problems.
Perfect.
Jaap Berkhout.
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-21 12:38 ` J.J. Berkhout
2022-09-21 14:54 ` J.J. Berkhout
@ 2022-09-21 18:32 ` Niklas Cassel
2022-09-26 12:59 ` J.J. Berkhout
2022-09-22 22:08 ` Damien Le Moal
2 siblings, 1 reply; 20+ messages in thread
From: Niklas Cassel @ 2022-09-21 18:32 UTC (permalink / raw)
To: J.J. Berkhout; +Cc: linux-ide
On Wed, Sep 21, 2022 at 02:38:51PM +0200, J.J. Berkhout wrote:
> On 21-09-2022 13:58, Niklas Cassel wrote:
> > Another way do disable lpm is to do:
> > $ sudo sh -c "echo max_performance > /sys/class/scsi_host/host13/link_power_management_policy"
>
> Yes, this worked and did the trick! Reading without any errors. I did
> not yet try to write, but will do so today.
> When booting with libata.force=nolpm the link_power_management_policy
> was still med_power_with_dipm and I got the dmesg:
>
> [ 0.291452] ata: failed to parse force parameter "nolpm" (unknown value)
>
> so the ineffectiveness of this boot parameter seems to be explained.
> Might there be some other syntax for this parameter?
Apparently this was introduced quite recently, in
commit 2c33bbdac28c ("ata: libata-core: Allow forcing most horkage flags")
which was first included in kernel v5.19.
>
> Nevertheless, my problem now has a work-around and I am very happy.
> Thanks, Niklas.
Great news!
Then I believe that
+ { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOLPM },
should be the proper quirk for your device.
If you could test it when you have time (again, no rush),
then we could send out a proper fix for this.
Kind regards,
Niklas
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-21 12:38 ` J.J. Berkhout
2022-09-21 14:54 ` J.J. Berkhout
2022-09-21 18:32 ` Niklas Cassel
@ 2022-09-22 22:08 ` Damien Le Moal
2022-09-23 12:07 ` J.J. Berkhout
2 siblings, 1 reply; 20+ messages in thread
From: Damien Le Moal @ 2022-09-22 22:08 UTC (permalink / raw)
To: J.J. Berkhout, linux-ide
On 9/21/22 21:38, J.J. Berkhout wrote:
> Hello,
>
>
>
> On 21-09-2022 13:58, Niklas Cassel wrote:
>> Another way do disable lpm is to do:
>>
>> $ ls -al /sys/class/scsi_host/host*
>>
>> Find your device in the list. My device is:
>> /sys/class/scsi_host/host13/
>>
>> Print the current lpm policy for your device:
>> $ cat /sys/class/scsi_host/host13/link_power_management_policy
>> med_power_with_dipm
>>
>> Anything other than "max_performance" means that you have (a varying degree)
>> of low power modes enabled.
>>
>> $ sudo sh -c "echo max_performance > /sys/class/scsi_host/host13/link_power_management_policy"
>>
>> $ cat /sys/class/scsi_host/host13/link_power_management_policy
>> max_performance
>>
>> Try reading from the optical drive after ensuring that the policy is
>> "max_performance".
>>
>
> Yes, this worked and did the trick! Reading without any errors. I did
> not yet try to write, but will do so today.
> When booting with libata.force=nolpm the link_power_management_policy
> was still med_power_with_dipm and I got the dmesg:
>
> [ 0.291452] ata: failed to parse force parameter "nolpm" (unknown value)
What kernel version are you running ? This should work with the latest
kernels. Your kernel likely pre-dates the addition of all the ata horkage
flag as boot parameter options, which I think was with 5.18 kernel.
>
> so the ineffectiveness of this boot parameter seems to be explained.
> Might there be some other syntax for this parameter?
>
> Nevertheless, my problem now has a work-around and I am very happy.
> Thanks, Niklas.
>
> Kind regards,
>
> Jaap Berkhout
--
Damien Le Moal
Western Digital Research
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-22 22:08 ` Damien Le Moal
@ 2022-09-23 12:07 ` J.J. Berkhout
2022-09-25 22:57 ` Damien Le Moal
0 siblings, 1 reply; 20+ messages in thread
From: J.J. Berkhout @ 2022-09-23 12:07 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 1798 bytes --]
On 23-09-2022 00:08, Damien Le Moal wrote:
> On 9/21/22 21:38, J.J. Berkhout wrote:
>> Hello,
>>
>>
>>
>> On 21-09-2022 13:58, Niklas Cassel wrote:
>>> Another way do disable lpm is to do:
>>>
>>> $ ls -al /sys/class/scsi_host/host*
>>>
>>> Find your device in the list. My device is:
>>> /sys/class/scsi_host/host13/
>>>
>>> Print the current lpm policy for your device:
>>> $ cat /sys/class/scsi_host/host13/link_power_management_policy
>>> med_power_with_dipm
>>>
>>> Anything other than "max_performance" means that you have (a varying degree)
>>> of low power modes enabled.
>>>
>>> $ sudo sh -c "echo max_performance > /sys/class/scsi_host/host13/link_power_management_policy"
>>>
>>> $ cat /sys/class/scsi_host/host13/link_power_management_policy
>>> max_performance
>>>
>>> Try reading from the optical drive after ensuring that the policy is
>>> "max_performance".
>>>
>>
>> Yes, this worked and did the trick! Reading without any errors. I did
>> not yet try to write, but will do so today.
>> When booting with libata.force=nolpm the link_power_management_policy
>> was still med_power_with_dipm and I got the dmesg:
>>
>> [ 0.291452] ata: failed to parse force parameter "nolpm" (unknown value)
>
> What kernel version are you running ? This should work with the latest
> kernels. Your kernel likely pre-dates the addition of all the ata horkage
> flag as boot parameter options, which I think was with 5.18 kernel.
Yep, I run Ubuntu 5.15.0-48-generic kernel. I circumvented this by
using sysfsutils with
class/scsi_host/host0/link_power_management_policy = max_performance
in the /etc/sysfs.conf file. As long as I don't mess around with my
hardware, the host number should stay the same.
Kind regards,
Jaap Berkhout
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-23 12:07 ` J.J. Berkhout
@ 2022-09-25 22:57 ` Damien Le Moal
0 siblings, 0 replies; 20+ messages in thread
From: Damien Le Moal @ 2022-09-25 22:57 UTC (permalink / raw)
To: J.J. Berkhout, linux-ide
On 9/23/22 21:07, J.J. Berkhout wrote:
>
>
> On 23-09-2022 00:08, Damien Le Moal wrote:
>> On 9/21/22 21:38, J.J. Berkhout wrote:
>>> Hello,
>>>
>>>
>>>
>>> On 21-09-2022 13:58, Niklas Cassel wrote:
>>>> Another way do disable lpm is to do:
>>>>
>>>> $ ls -al /sys/class/scsi_host/host*
>>>>
>>>> Find your device in the list. My device is:
>>>> /sys/class/scsi_host/host13/
>>>>
>>>> Print the current lpm policy for your device:
>>>> $ cat /sys/class/scsi_host/host13/link_power_management_policy
>>>> med_power_with_dipm
>>>>
>>>> Anything other than "max_performance" means that you have (a varying degree)
>>>> of low power modes enabled.
>>>>
>>>> $ sudo sh -c "echo max_performance > /sys/class/scsi_host/host13/link_power_management_policy"
>>>>
>>>> $ cat /sys/class/scsi_host/host13/link_power_management_policy
>>>> max_performance
>>>>
>>>> Try reading from the optical drive after ensuring that the policy is
>>>> "max_performance".
>>>>
>>>
>>> Yes, this worked and did the trick! Reading without any errors. I did
>>> not yet try to write, but will do so today.
>>> When booting with libata.force=nolpm the link_power_management_policy
>>> was still med_power_with_dipm and I got the dmesg:
>>>
>>> [ 0.291452] ata: failed to parse force parameter "nolpm" (unknown value)
>>
>> What kernel version are you running ? This should work with the latest
>> kernels. Your kernel likely pre-dates the addition of all the ata horkage
>> flag as boot parameter options, which I think was with 5.18 kernel.
>
> Yep, I run Ubuntu 5.15.0-48-generic kernel. I circumvented this by
> using sysfsutils with
> class/scsi_host/host0/link_power_management_policy = max_performance
> in the /etc/sysfs.conf file. As long as I don't mess around with my
> hardware, the host number should stay the same.
OK. Then "nolpm" not being a valid parameter is normal then. I wanted to
make sure there is no bug in the parameters handling :)
>
> Kind regards,
>
> Jaap Berkhout
--
Damien Le Moal
Western Digital Research
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-21 18:32 ` Niklas Cassel
@ 2022-09-26 12:59 ` J.J. Berkhout
2022-09-26 14:39 ` Niklas Cassel
2022-09-26 14:50 ` J.J. Berkhout
0 siblings, 2 replies; 20+ messages in thread
From: J.J. Berkhout @ 2022-09-26 12:59 UTC (permalink / raw)
To: Niklas Cassel; +Cc: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 3446 bytes --]
On 21-09-2022 20:32, Niklas Cassel wrote:
> On Wed, Sep 21, 2022 at 02:38:51PM +0200, J.J. Berkhout wrote:
>> On 21-09-2022 13:58, Niklas Cassel wrote:
>>> Another way do disable lpm is to do:
>>> $ sudo sh -c "echo max_performance > /sys/class/scsi_host/host13/link_power_management_policy"
>>
>> Yes, this worked and did the trick! Reading without any errors. I did
>> not yet try to write, but will do so today.
>> When booting with libata.force=nolpm the link_power_management_policy
>> was still med_power_with_dipm and I got the dmesg:
>>
>> [ 0.291452] ata: failed to parse force parameter "nolpm" (unknown value)
>>
>> so the ineffectiveness of this boot parameter seems to be explained.
>> Might there be some other syntax for this parameter?
>
> Apparently this was introduced quite recently, in
> commit 2c33bbdac28c ("ata: libata-core: Allow forcing most horkage flags")
> which was first included in kernel v5.19.
>
>>
>> Nevertheless, my problem now has a work-around and I am very happy.
>> Thanks, Niklas.
>
> Great news!
>
> Then I believe that
> + { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOLPM },
> should be the proper quirk for your device.
>
> If you could test it when you have time (again, no rush),
> then we could send out a proper fix for this.
>
>
> Kind regards,
> Niklas
OK, I got around to testing the patch.
I used kernel 5.19.11 (from https://cdn.kernel.org/pub).
After solving the problem with errors with the compilation (I removed
the NVIDIA driver and switched to the nouveau driver) and space problems
on my /boot partition (solved by using sudo make INSTALL_MOD_STRIP=1
modules_install) I got the following results:
Try 1:
patching libata-core.c with the lines
/* PIONEER BD-RW BDR-207M and PIONEER BD-RW BDR-205 have broken LPM
support */
{ "PIONEER BD-RW DVR-207M", NULL, ATA_HORKAGE_NOLPM },
{ "PIONEER BD-RW DVR-205", NULL, ATA_HORKAGE_NOLPM },
resulted in
link_power_management_policy still "med_power_with_dipm"
problem with pioneer DOES occur
Try 2:
patching libata-core.c with the lines
/* PIONEER BD-RW BDR-207M and PIONEER BD-RW BDR-205 have broken LPM
support */
{ "PIONEER BD-RW DVR-207M", NULL, ATA_HORKAGE_NOSETXFER },
{ "PIONEER BD-RW DVR-205", NULL, ATA_HORKAGE_NOSETXFER },
resulted in
link_power_management_policy still "med_power_with_dipm"
problem with pioneer DOES occur
Try 3:
patching libata-core.c with the lines
/* PIONEER BD-RW BDR-207M and PIONEER BD-RW BDR-205 have broken LPM
support */
{ "PIONEER BD-RW DVR-207M", NULL, ATA_HORKAGE_NOSETXFER |
ATA_HORKAGE_NOLPM },
{ "PIONEER BD-RW DVR-205", NULL, ATA_HORKAGE_NOSETXFER |
ATA_HORKAGE_NOLPM },
resulted in
link_power_management_policy still "med_power_with_dipm"
problem with pioneer DOES occur, additional error in log:
device offline error, dev sr0, sector 1365828 op 0x0:(READ) flags 0x0
phys_seg 1 prio class 0
(not sure if this is significant)'
Try 4:
unpatched libata-core.c
using boot kernel parameter "libata.force=1:nolpm"
resulted in
link_power_management_policy now "max_performance"
problem with pioneer DOES NOT occur
so libata.force=nolpm kernel parameter works, which might interest
Damien ;-)
Niklas, if you want to try other patches for this problem, I wouldbe
happy to be of assistance.
With kind regards,
Jaap Berkhout
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-26 12:59 ` J.J. Berkhout
@ 2022-09-26 14:39 ` Niklas Cassel
2022-09-26 14:50 ` J.J. Berkhout
1 sibling, 0 replies; 20+ messages in thread
From: Niklas Cassel @ 2022-09-26 14:39 UTC (permalink / raw)
To: J.J. Berkhout; +Cc: linux-ide
On Mon, Sep 26, 2022 at 02:59:19PM +0200, J.J. Berkhout wrote:
>
> OK, I got around to testing the patch.
> I used kernel 5.19.11 (from https://cdn.kernel.org/pub).
> After solving the problem with errors with the compilation (I removed
> the NVIDIA driver and switched to the nouveau driver) and space problems
> on my /boot partition (solved by using sudo make INSTALL_MOD_STRIP=1
> modules_install) I got the following results:
>
> Try 1:
> patching libata-core.c with the lines
> /* PIONEER BD-RW BDR-207M and PIONEER BD-RW BDR-205 have broken LPM
> support */
> { "PIONEER BD-RW DVR-207M", NULL, ATA_HORKAGE_NOLPM },
> { "PIONEER BD-RW DVR-205", NULL, ATA_HORKAGE_NOLPM },
>
> resulted in
> link_power_management_policy still "med_power_with_dipm"
> problem with pioneer DOES occur
Thanks for testing!
libata-core.c has this:
if (dev->horkage & ATA_HORKAGE_NOLPM) {
ata_dev_warn(dev, "LPM support broken, forcing max_power\n");
dev->link->ap->target_lpm_policy = ATA_LPM_MAX_POWER;
}
and
libata-sata.c:ata_scsi_lpm_show() has this:
return sysfs_emit(buf, "%s\n",
ata_lpm_policy_names[ap->target_lpm_policy]);
so
/sys/class/scsi_host/hostXXX/link_power_management_policy
should definitely show "max_performance" when the quirk is applied.
My suggestion was to try:
+ { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOLPM },
However you tested:
+ { "PIONEER BD-RW DVR-207M", NULL, ATA_HORKAGE_NOLPM },
So I think that you simply did a typo in the name.
Looking at you dmesg again however:
[ 1.043657] ata1.00: ATAPI: PIONEER BD-RW BDR-207M, 1.60, max UDMA/100
[ 1.057988] scsi 0:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.60 PQ: 0 ANSI: 5
It seems to print two different strings:
"PIONEER BD-RW BDR-207M"
"PIONEER BD-RW BDR-207M"
So I'm actually not really sure which is correct...
I guess try both and see which one that works? :)
Kind regards,
Niklas
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Multiple errors with DVD drive
2022-09-26 12:59 ` J.J. Berkhout
2022-09-26 14:39 ` Niklas Cassel
@ 2022-09-26 14:50 ` J.J. Berkhout
1 sibling, 0 replies; 20+ messages in thread
From: J.J. Berkhout @ 2022-09-26 14:50 UTC (permalink / raw)
To: Niklas Cassel; +Cc: linux-ide
[-- Attachment #1.1: Type: text/plain, Size: 4217 bytes --]
On 26-09-2022 14:59, J.J. Berkhout wrote:
>
>
> On 21-09-2022 20:32, Niklas Cassel wrote:
>> On Wed, Sep 21, 2022 at 02:38:51PM +0200, J.J. Berkhout wrote:
>>> On 21-09-2022 13:58, Niklas Cassel wrote:
>>>> Another way do disable lpm is to do:
>>>> $ sudo sh -c "echo max_performance > /sys/class/scsi_host/host13/link_power_management_policy"
>>>
>>> Yes, this worked and did the trick! Reading without any errors. I did
>>> not yet try to write, but will do so today.
>>> When booting with libata.force=nolpm the link_power_management_policy
>>> was still med_power_with_dipm and I got the dmesg:
>>>
>>> [ 0.291452] ata: failed to parse force parameter "nolpm" (unknown value)
>>>
>>> so the ineffectiveness of this boot parameter seems to be explained.
>>> Might there be some other syntax for this parameter?
>>
>> Apparently this was introduced quite recently, in
>> commit 2c33bbdac28c ("ata: libata-core: Allow forcing most horkage flags")
>> which was first included in kernel v5.19.
>>
>>>
>>> Nevertheless, my problem now has a work-around and I am very happy.
>>> Thanks, Niklas.
>>
>> Great news!
>>
>> Then I believe that
>> + { "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOLPM },
>> should be the proper quirk for your device.
>>
>> If you could test it when you have time (again, no rush),
>> then we could send out a proper fix for this.
>>
>>
>> Kind regards,
>> Niklas
>
> OK, I got around to testing the patch.
> I used kernel 5.19.11 (from https://cdn.kernel.org/pub).
> After solving the problem with errors with the compilation (I removed
> the NVIDIA driver and switched to the nouveau driver) and space problems
> on my /boot partition (solved by using sudo make INSTALL_MOD_STRIP=1
> modules_install) I got the following results:
>
> Try 1:
> patching libata-core.c with the lines
> /* PIONEER BD-RW BDR-207M and PIONEER BD-RW BDR-205 have broken LPM
> support */
> { "PIONEER BD-RW DVR-207M", NULL, ATA_HORKAGE_NOLPM },
> { "PIONEER BD-RW DVR-205", NULL, ATA_HORKAGE_NOLPM },
>
> resulted in
> link_power_management_policy still "med_power_with_dipm"
> problem with pioneer DOES occur
>
> Try 2:
> patching libata-core.c with the lines
> /* PIONEER BD-RW BDR-207M and PIONEER BD-RW BDR-205 have broken LPM
> support */
> { "PIONEER BD-RW DVR-207M", NULL, ATA_HORKAGE_NOSETXFER },
> { "PIONEER BD-RW DVR-205", NULL, ATA_HORKAGE_NOSETXFER },
>
> resulted in
> link_power_management_policy still "med_power_with_dipm"
> problem with pioneer DOES occur
>
> Try 3:
> patching libata-core.c with the lines
> /* PIONEER BD-RW BDR-207M and PIONEER BD-RW BDR-205 have broken LPM
> support */
> { "PIONEER BD-RW DVR-207M", NULL, ATA_HORKAGE_NOSETXFER |
> ATA_HORKAGE_NOLPM },
> { "PIONEER BD-RW DVR-205", NULL, ATA_HORKAGE_NOSETXFER |
> ATA_HORKAGE_NOLPM },
>
> resulted in
> link_power_management_policy still "med_power_with_dipm"
> problem with pioneer DOES occur, additional error in log:
> device offline error, dev sr0, sector 1365828 op 0x0:(READ) flags 0x0
> phys_seg 1 prio class 0
> (not sure if this is significant)'
>
> Try 4:
> unpatched libata-core.c
> using boot kernel parameter "libata.force=1:nolpm"
>
> resulted in
> link_power_management_policy now "max_performance"
> problem with pioneer DOES NOT occur
> so libata.force=nolpm kernel parameter works, which might interest
> Damien ;-)
>
> Niklas, if you want to try other patches for this problem, I wouldbe
> happy to be of assistance.
>
> With kind regards,
>
> Jaap Berkhout
Update:
I am sorry to have to report I made a mistake. Instead of "PIONEER
BD-RW BDR-207M" I used "BD-RW DVR-207M", which is obviously wrong. I
just now corrected this am am happy to report that with the patch:
/* PIONEER BD-RW BDR-207M and PIONEER BD-RW BDR-205 have broken LPM
support */
{ "PIONEER BD-RW BDR-207M", NULL, ATA_HORKAGE_NOLPM },
{ "PIONEER BD-RW BDR-205", NULL, ATA_HORKAGE_NOLPM },
the problem with the optical drive is solved.
Please consider this mistake as a senior moment.
With kind regards,
Jaap Berkhout.
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2022-09-26 16:03 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-05-26 12:38 Multiple errors with DVD drive J.J. Berkhout
2022-05-26 23:36 ` Damien Le Moal
2022-05-27 8:50 ` J.J. Berkhout
2022-05-27 10:32 ` J.J. Berkhout
2022-08-05 9:17 ` J.J. Berkhout
2022-09-20 10:05 ` J.J. Berkhout
2022-09-20 13:06 ` Niklas Cassel
[not found] ` <9756ac37-6790-7b83-5840-abe04f8ab838@staalenberk.nl>
2022-09-20 21:08 ` Niklas Cassel
2022-09-21 10:28 ` J.J. Berkhout
2022-09-21 11:58 ` Niklas Cassel
2022-09-21 12:38 ` J.J. Berkhout
2022-09-21 14:54 ` J.J. Berkhout
2022-09-21 18:32 ` Niklas Cassel
2022-09-26 12:59 ` J.J. Berkhout
2022-09-26 14:39 ` Niklas Cassel
2022-09-26 14:50 ` J.J. Berkhout
2022-09-22 22:08 ` Damien Le Moal
2022-09-23 12:07 ` J.J. Berkhout
2022-09-25 22:57 ` Damien Le Moal
2022-09-20 13:35 ` Niklas Cassel
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.