* [PATCH v2 2/9] ARM: dts: imx28: rename mmc2_sck_cfg to prepare for an alternative muxing setup
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-22 22:22 ` Michael Heimpold
-1 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, stefan.wahren-eS4NqCHxEME,
Michael Heimpold
From: Michael Heimpold <michael.heimpold-eS4NqCHxEME@public.gmane.org>
Signed-off-by: Michael Heimpold <michael.heimpold-eS4NqCHxEME@public.gmane.org>
---
arch/arm/boot/dts/imx28-m28cu3.dts | 2 +-
arch/arm/boot/dts/imx28.dtsi | 3 ++-
2 files changed, 3 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts
index 2df63be..bb53294 100644
--- a/arch/arm/boot/dts/imx28-m28cu3.dts
+++ b/arch/arm/boot/dts/imx28-m28cu3.dts
@@ -57,7 +57,7 @@
pinctrl-names = "default";
pinctrl-0 = <&mmc2_4bit_pins_a
&mmc2_cd_cfg
- &mmc2_sck_cfg>;
+ &mmc2_sck_cfg_a>;
bus-width = <4>;
vmmc-supply = <®_vddio_sd1>;
status = "okay";
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index bc5cf41..857ca37 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -604,7 +604,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- mmc2_sck_cfg: mmc2-sck-cfg {
+ mmc2_sck_cfg_a: mmc2-sck-cfg@0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__SSP2_SCK
>;
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH v2 2/9] ARM: dts: imx28: rename mmc2_sck_cfg to prepare for an alternative muxing setup
@ 2017-01-22 22:22 ` Michael Heimpold
0 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: linux-arm-kernel
From: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
---
arch/arm/boot/dts/imx28-m28cu3.dts | 2 +-
arch/arm/boot/dts/imx28.dtsi | 3 ++-
2 files changed, 3 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts
index 2df63be..bb53294 100644
--- a/arch/arm/boot/dts/imx28-m28cu3.dts
+++ b/arch/arm/boot/dts/imx28-m28cu3.dts
@@ -57,7 +57,7 @@
pinctrl-names = "default";
pinctrl-0 = <&mmc2_4bit_pins_a
&mmc2_cd_cfg
- &mmc2_sck_cfg>;
+ &mmc2_sck_cfg_a>;
bus-width = <4>;
vmmc-supply = <®_vddio_sd1>;
status = "okay";
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index bc5cf41..857ca37 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -604,7 +604,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- mmc2_sck_cfg: mmc2-sck-cfg {
+ mmc2_sck_cfg_a: mmc2-sck-cfg at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__SSP2_SCK
>;
--
2.7.4
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v2 3/9] ARM: dts: imx28: add alternative muxing for mmc2_sck_cfg
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-22 22:22 ` Michael Heimpold
-1 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, stefan.wahren-eS4NqCHxEME,
Michael Heimpold
From: Michael Heimpold <michael.heimpold-eS4NqCHxEME@public.gmane.org>
Signed-off-by: Michael Heimpold <michael.heimpold-eS4NqCHxEME@public.gmane.org>
---
arch/arm/boot/dts/imx28.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index 857ca37..5c65fa1 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -613,6 +613,15 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
+ mmc2_sck_cfg_b: mmc2-sck-cfg@1 {
+ reg = <1>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__SSP2_SCK
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
i2c0_pins_a: i2c0@0 {
reg = <0>;
fsl,pinmux-ids = <
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH v2 3/9] ARM: dts: imx28: add alternative muxing for mmc2_sck_cfg
@ 2017-01-22 22:22 ` Michael Heimpold
0 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: linux-arm-kernel
From: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
---
arch/arm/boot/dts/imx28.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index 857ca37..5c65fa1 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -613,6 +613,15 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
+ mmc2_sck_cfg_b: mmc2-sck-cfg at 1 {
+ reg = <1>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__SSP2_SCK
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
i2c0_pins_a: i2c0 at 0 {
reg = <0>;
fsl,pinmux-ids = <
--
2.7.4
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v2 4/9] ARM: dts: imx28-duckbill: enable spi, i2c and uart pins
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-22 22:22 ` Michael Heimpold
-1 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, stefan.wahren-eS4NqCHxEME,
Michael Heimpold
While at tweak some more settings for the default product:
- enable lradc
- adjust USB dr mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
Signed-off-by: Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
---
arch/arm/boot/dts/imx28-duckbill.dts | 81 +++++++++++++++++++++++++-----------
1 file changed, 56 insertions(+), 25 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts
index ce1a7ef..3e4385d 100644
--- a/arch/arm/boot/dts/imx28-duckbill.dts
+++ b/arch/arm/boot/dts/imx28-duckbill.dts
@@ -1,5 +1,6 @@
/*
- * Copyright (C) 2013 Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
+ * Copyright (C) 2013-2014,2016 Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
+ * Copyright (C) 2015-2017 I2SE GmbH <info-eS4NqCHxEME@public.gmane.org>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
@@ -10,6 +11,7 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
@@ -32,6 +34,13 @@
status = "okay";
};
+ ssp2: ssp@80014000 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+ };
+
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
@@ -39,14 +48,24 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- led_pins_a: led_gpio@0 {
+ led_pins: leds@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__GPIO_3_4
@@ -60,6 +79,22 @@
};
apbx@80040000 {
+ lradc@80050000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@80058000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ };
+
+ auart0: serial@8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
@@ -75,47 +110,43 @@
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
+ dr_mode = "peripheral";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <®_3p3v>;
phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
+ phy-reset-duration = <25>;
status = "okay";
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_3p3v: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
- pinctrl-0 = <&led_pins_a>;
+ pinctrl-0 = <&led_pins>;
- status {
- label = "duckbill:green:status";
- gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
- };
-
- failure {
+ status-red {
label = "duckbill:red:status";
gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
};
};
};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH v2 4/9] ARM: dts: imx28-duckbill: enable spi, i2c and uart pins
@ 2017-01-22 22:22 ` Michael Heimpold
0 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: linux-arm-kernel
While at tweak some more settings for the default product:
- enable lradc
- adjust USB dr mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
---
arch/arm/boot/dts/imx28-duckbill.dts | 81 +++++++++++++++++++++++++-----------
1 file changed, 56 insertions(+), 25 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts
index ce1a7ef..3e4385d 100644
--- a/arch/arm/boot/dts/imx28-duckbill.dts
+++ b/arch/arm/boot/dts/imx28-duckbill.dts
@@ -1,5 +1,6 @@
/*
- * Copyright (C) 2013 Michael Heimpold <mhei@heimpold.de>
+ * Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
@@ -10,6 +11,7 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
@@ -32,6 +34,13 @@
status = "okay";
};
+ ssp2: ssp at 80014000 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+ };
+
pinctrl at 80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
@@ -39,14 +48,24 @@
hog_pins_a: hog at 0 {
reg = <0>;
fsl,pinmux-ids = <
- MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- led_pins_a: led_gpio at 0 {
+ led_pins: leds at 0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__GPIO_3_4
@@ -60,6 +79,22 @@
};
apbx at 80040000 {
+ lradc at 80050000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@80058000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ };
+
+ auart0: serial at 8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
duart: serial at 80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
@@ -75,47 +110,43 @@
ahb at 80080000 {
usb0: usb at 80080000 {
status = "okay";
+ dr_mode = "peripheral";
};
mac0: ethernet at 800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <®_3p3v>;
phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
+ phy-reset-duration = <25>;
status = "okay";
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_3p3v: regulator at 0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
- pinctrl-0 = <&led_pins_a>;
+ pinctrl-0 = <&led_pins>;
- status {
- label = "duckbill:green:status";
- gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
- };
-
- failure {
+ status-red {
label = "duckbill:red:status";
gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
};
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 36+ messages in thread[parent not found: <1485123764-14754-5-git-send-email-mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>]
* Re: [PATCH v2 4/9] ARM: dts: imx28-duckbill: enable spi, i2c and uart pins
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-23 17:00 ` Stefan Wahren
-1 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:00 UTC (permalink / raw)
To: Michael Heimpold, shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Fabio Estevam
Hi,
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> While at tweak some more settings for the default product:
> - enable lradc
> - adjust USB dr mode
> - add default triggers for LEDs
> - get rid of regulators simple-bus container
> - adjust phy reset duration
since the subject line suggests something different as the actual
complete patch does, this needs to be changed.
@Shawn, @Fabio: Do we need a single patch for every point or is it
possible to squash some?
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 4/9] ARM: dts: imx28-duckbill: enable spi, i2c and uart pins
@ 2017-01-23 17:00 ` Stefan Wahren
0 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:00 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> While at tweak some more settings for the default product:
> - enable lradc
> - adjust USB dr mode
> - add default triggers for LEDs
> - get rid of regulators simple-bus container
> - adjust phy reset duration
since the subject line suggests something different as the actual
complete patch does, this needs to be changed.
@Shawn, @Fabio: Do we need a single patch for every point or is it
possible to squash some?
^ permalink raw reply [flat|nested] 36+ messages in thread
[parent not found: <96eabd96-64a6-7fbc-bb4b-223244358a42-eS4NqCHxEME@public.gmane.org>]
* Re: [PATCH v2 4/9] ARM: dts: imx28-duckbill: enable spi, i2c and uart pins
2017-01-23 17:00 ` Stefan Wahren
@ 2017-01-24 13:00 ` Shawn Guo
-1 siblings, 0 replies; 36+ messages in thread
From: Shawn Guo @ 2017-01-24 13:00 UTC (permalink / raw)
To: Stefan Wahren
Cc: Michael Heimpold, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Fabio Estevam
On Mon, Jan 23, 2017 at 06:00:02PM +0100, Stefan Wahren wrote:
> Hi,
>
> Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> > While at tweak some more settings for the default product:
> > - enable lradc
> > - adjust USB dr mode
> > - add default triggers for LEDs
> > - get rid of regulators simple-bus container
> > - adjust phy reset duration
>
> since the subject line suggests something different as the actual
> complete patch does, this needs to be changed.
>
> @Shawn, @Fabio: Do we need a single patch for every point or is it
> possible to squash some?
I prefer to squash if possible.
Shawn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 4/9] ARM: dts: imx28-duckbill: enable spi, i2c and uart pins
@ 2017-01-24 13:00 ` Shawn Guo
0 siblings, 0 replies; 36+ messages in thread
From: Shawn Guo @ 2017-01-24 13:00 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Jan 23, 2017 at 06:00:02PM +0100, Stefan Wahren wrote:
> Hi,
>
> Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> > While at tweak some more settings for the default product:
> > - enable lradc
> > - adjust USB dr mode
> > - add default triggers for LEDs
> > - get rid of regulators simple-bus container
> > - adjust phy reset duration
>
> since the subject line suggests something different as the actual
> complete patch does, this needs to be changed.
>
> @Shawn, @Fabio: Do we need a single patch for every point or is it
> possible to squash some?
I prefer to squash if possible.
Shawn
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 5/9] ARM: dts: add support for I2SE Duckbill 2 boards
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-22 22:22 ` Michael Heimpold
-1 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, stefan.wahren-eS4NqCHxEME,
Michael Heimpold
This machine is an USB pen drive sized development board,
based on NXP's i.MX28 CPU. In contrast to the previous
model "Duckbill", the "Duckbill 2" series has internal
eMMC storage.
Signed-off-by: Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
Cc: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx28-duckbill-2.dts | 183 +++++++++++++++++++++++++++++++++
2 files changed, 184 insertions(+)
create mode 100644 arch/arm/boot/dts/imx28-duckbill-2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f10fe85..fa4664b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -475,6 +475,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-cfa10056.dtb \
imx28-cfa10057.dtb \
imx28-cfa10058.dtb \
+ imx28-duckbill-2.dtb \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
imx28-eukrea-mbmx287lc.dtb \
diff --git a/arch/arm/boot/dts/imx28-duckbill-2.dts b/arch/arm/boot/dts/imx28-duckbill-2.dts
new file mode 100644
index 0000000..2510b20
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill-2.dts
@@ -0,0 +1,183 @@
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info-eS4NqCHxEME@public.gmane.org>
+ * Copyright (C) 2016 Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill 2";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+ };
+
+ ssp2: ssp@80014000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_b
+ &mmc2_cd_cfg &mmc2_sck_cfg_b>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: leds@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx@80040000 {
+ lradc@80050000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@80058000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ };
+
+ auart0: serial@8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
+ duart: serial@80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy@8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ usb0: usb@80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet@800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH v2 5/9] ARM: dts: add support for I2SE Duckbill 2 boards
@ 2017-01-22 22:22 ` Michael Heimpold
0 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: linux-arm-kernel
This machine is an USB pen drive sized development board,
based on NXP's i.MX28 CPU. In contrast to the previous
model "Duckbill", the "Duckbill 2" series has internal
eMMC storage.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx28-duckbill-2.dts | 183 +++++++++++++++++++++++++++++++++
2 files changed, 184 insertions(+)
create mode 100644 arch/arm/boot/dts/imx28-duckbill-2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f10fe85..fa4664b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -475,6 +475,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-cfa10056.dtb \
imx28-cfa10057.dtb \
imx28-cfa10058.dtb \
+ imx28-duckbill-2.dtb \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
imx28-eukrea-mbmx287lc.dtb \
diff --git a/arch/arm/boot/dts/imx28-duckbill-2.dts b/arch/arm/boot/dts/imx28-duckbill-2.dts
new file mode 100644
index 0000000..2510b20
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill-2.dts
@@ -0,0 +1,183 @@
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill 2";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb at 80000000 {
+ apbh at 80000000 {
+ ssp0: ssp at 80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+ };
+
+ ssp2: ssp at 80014000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_b
+ &mmc2_cd_cfg &mmc2_sck_cfg_b>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ pinctrl at 80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: leds at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx at 80040000 {
+ lradc at 80050000 {
+ status = "okay";
+ };
+
+ i2c0: i2c at 80058000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ };
+
+ auart0: serial at 8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
+ duart: serial at 80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy at 8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb at 80080000 {
+ usb0: usb at 80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet at 800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v2 6/9] ARM: dts: add support for I2SE Duckbill 2 485
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-22 22:22 ` Michael Heimpold
-1 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, stefan.wahren-eS4NqCHxEME,
Michael Heimpold
This machine is based on I2SE's Duckbill 2 board and features a
RS-485 daugther board. This device is intended to be used for
e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
Cc: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx28-duckbill-2-485.dts | 189 +++++++++++++++++++++++++++++
2 files changed, 190 insertions(+)
create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-485.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index fa4664b..e0f3f4e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -475,6 +475,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-cfa10056.dtb \
imx28-cfa10057.dtb \
imx28-cfa10058.dtb \
+ imx28-duckbill-2-485.dts \
imx28-duckbill-2.dtb \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
new file mode 100644
index 0000000..a748968
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
@@ -0,0 +1,189 @@
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info-eS4NqCHxEME@public.gmane.org>
+ * Copyright (C) 2016 Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill 2 485";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+ };
+
+ ssp2: ssp@80014000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_b
+ &mmc2_cd_cfg &mmc2_sck_cfg_b>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: leds@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx@80040000 {
+ lradc@80050000 {
+ status = "okay";
+ };
+
+ auart0: serial@8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
+ duart: serial@80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy@8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ usb0: usb@80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet@800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ rs485-red {
+ label = "duckbill:red:rs485";
+ gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+ };
+
+ rs485-green {
+ label = "duckbill:green:rs485";
+ gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH v2 6/9] ARM: dts: add support for I2SE Duckbill 2 485
@ 2017-01-22 22:22 ` Michael Heimpold
0 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: linux-arm-kernel
This machine is based on I2SE's Duckbill 2 board and features a
RS-485 daugther board. This device is intended to be used for
e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx28-duckbill-2-485.dts | 189 +++++++++++++++++++++++++++++
2 files changed, 190 insertions(+)
create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-485.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index fa4664b..e0f3f4e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -475,6 +475,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-cfa10056.dtb \
imx28-cfa10057.dtb \
imx28-cfa10058.dtb \
+ imx28-duckbill-2-485.dts \
imx28-duckbill-2.dtb \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
new file mode 100644
index 0000000..a748968
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
@@ -0,0 +1,189 @@
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill 2 485";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb at 80000000 {
+ apbh at 80000000 {
+ ssp0: ssp at 80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+ };
+
+ ssp2: ssp at 80014000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_b
+ &mmc2_cd_cfg &mmc2_sck_cfg_b>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ pinctrl at 80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: leds at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx at 80040000 {
+ lradc at 80050000 {
+ status = "okay";
+ };
+
+ auart0: serial at 8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
+ duart: serial at 80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy at 8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb at 80080000 {
+ usb0: usb at 80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet at 800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ rs485-red {
+ label = "duckbill:red:rs485";
+ gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+ };
+
+ rs485-green {
+ label = "duckbill:green:rs485";
+ gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 36+ messages in thread[parent not found: <1485123764-14754-7-git-send-email-mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>]
* Re: [PATCH v2 6/9] ARM: dts: add support for I2SE Duckbill 2 485
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-23 17:10 ` Stefan Wahren
-1 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:10 UTC (permalink / raw)
To: Michael Heimpold, shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Fabio Estevam
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> This machine is based on I2SE's Duckbill 2 board and features a
> RS-485 daugther board. This device is intended to be used for
> e.g. home automation purposes.
>
> Signed-off-by: Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
> Cc: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx28-duckbill-2-485.dts | 189 +++++++++++++++++++++++++++++
> 2 files changed, 190 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-485.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index fa4664b..e0f3f4e 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -475,6 +475,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
> imx28-cfa10056.dtb \
> imx28-cfa10057.dtb \
> imx28-cfa10058.dtb \
> + imx28-duckbill-2-485.dts \
The file ending should be dtb. This issue applies also to patch 7 and 8.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 6/9] ARM: dts: add support for I2SE Duckbill 2 485
@ 2017-01-23 17:10 ` Stefan Wahren
0 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:10 UTC (permalink / raw)
To: linux-arm-kernel
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> This machine is based on I2SE's Duckbill 2 board and features a
> RS-485 daugther board. This device is intended to be used for
> e.g. home automation purposes.
>
> Signed-off-by: Michael Heimpold <mhei@heimpold.de>
> Cc: Stefan Wahren <stefan.wahren@i2se.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx28-duckbill-2-485.dts | 189 +++++++++++++++++++++++++++++
> 2 files changed, 190 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-485.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index fa4664b..e0f3f4e 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -475,6 +475,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
> imx28-cfa10056.dtb \
> imx28-cfa10057.dtb \
> imx28-cfa10058.dtb \
> + imx28-duckbill-2-485.dts \
The file ending should be dtb. This issue applies also to patch 7 and 8.
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 7/9] ARM: dts: add support for I2SE Duckbill 2 EnOcean
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-22 22:22 ` Michael Heimpold
-1 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, stefan.wahren-eS4NqCHxEME,
Michael Heimpold
This machine is based on I2SE's Duckbill 2 board and features a
EnOcean daugther board based on the popular TCM310 chipset.
This product is intended to be used for e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
Cc: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx28-duckbill-2-enocean.dts | 220 +++++++++++++++++++++++++
2 files changed, 221 insertions(+)
create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e0f3f4e..d7fcb4dc 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -477,6 +477,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-cfa10058.dtb \
imx28-duckbill-2-485.dts \
imx28-duckbill-2.dtb \
+ imx28-duckbill-2-enocean.dts \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
imx28-eukrea-mbmx287lc.dtb \
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
new file mode 100644
index 0000000..6e7a71c
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
@@ -0,0 +1,220 @@
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info-eS4NqCHxEME@public.gmane.org>
+ * Copyright (C) 2016 Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill 2 EnOcean";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+ };
+
+ ssp2: ssp@80014000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_b
+ &mmc2_cd_cfg &mmc2_sck_cfg_b>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: leds@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ MX28_PAD_AUART0_CTS__GPIO_3_2
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ enocean_button: enocean-button@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART0_RTS__GPIO_3_3
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx@80040000 {
+ lradc@80050000 {
+ status = "okay";
+ };
+
+ auart0: serial@8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
+ duart: serial@80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy@8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ usb0: usb@80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet@800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ enocean-blue {
+ label = "duckbill:blue:enocean";
+ gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+ };
+
+ enocean-red {
+ label = "duckbill:red:enocean";
+ gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+ };
+
+ enocean-green {
+ label = "duckbill:green:enocean";
+ gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&enocean_button>;
+
+ enocean {
+ label = "EnOcean";
+ linux,code = <KEY_NEW>;
+ gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH v2 7/9] ARM: dts: add support for I2SE Duckbill 2 EnOcean
@ 2017-01-22 22:22 ` Michael Heimpold
0 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: linux-arm-kernel
This machine is based on I2SE's Duckbill 2 board and features a
EnOcean daugther board based on the popular TCM310 chipset.
This product is intended to be used for e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx28-duckbill-2-enocean.dts | 220 +++++++++++++++++++++++++
2 files changed, 221 insertions(+)
create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e0f3f4e..d7fcb4dc 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -477,6 +477,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-cfa10058.dtb \
imx28-duckbill-2-485.dts \
imx28-duckbill-2.dtb \
+ imx28-duckbill-2-enocean.dts \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
imx28-eukrea-mbmx287lc.dtb \
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
new file mode 100644
index 0000000..6e7a71c
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
@@ -0,0 +1,220 @@
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill 2 EnOcean";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb at 80000000 {
+ apbh at 80000000 {
+ ssp0: ssp at 80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+ };
+
+ ssp2: ssp at 80014000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_b
+ &mmc2_cd_cfg &mmc2_sck_cfg_b>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ pinctrl at 80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: leds at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ MX28_PAD_AUART0_CTS__GPIO_3_2
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ enocean_button: enocean-button at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART0_RTS__GPIO_3_3
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx at 80040000 {
+ lradc at 80050000 {
+ status = "okay";
+ };
+
+ auart0: serial at 8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
+ duart: serial at 80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy at 8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb at 80080000 {
+ usb0: usb at 80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet at 800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ enocean-blue {
+ label = "duckbill:blue:enocean";
+ gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+ };
+
+ enocean-red {
+ label = "duckbill:red:enocean";
+ gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+ };
+
+ enocean-green {
+ label = "duckbill:green:enocean";
+ gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&enocean_button>;
+
+ enocean {
+ label = "EnOcean";
+ linux,code = <KEY_NEW>;
+ gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v2 8/9] ARM: dts: add support for I2SE Duckbill 2 SPI
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-22 22:22 ` Michael Heimpold
-1 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, stefan.wahren-eS4NqCHxEME,
Michael Heimpold
This machine is based on I2SE's Duckbill 2 board and is sold as part of I2SE's
PLC Bundle for IoT. This is a development kit for Homeplug Green PHY based
powerline products based on Qualcomms QCA7000 chip.
Signed-off-by: Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
Cc: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx28-duckbill-2-spi.dts | 199 +++++++++++++++++++++++++++++
2 files changed, 200 insertions(+)
create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-spi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d7fcb4dc..d2d2486 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -478,6 +478,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-duckbill-2-485.dts \
imx28-duckbill-2.dtb \
imx28-duckbill-2-enocean.dts \
+ imx28-duckbill-2-spi.dts \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
imx28-eukrea-mbmx287lc.dtb \
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
new file mode 100644
index 0000000..738eaa7
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
@@ -0,0 +1,199 @@
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info-eS4NqCHxEME@public.gmane.org>
+ * Copyright (C) 2016 Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill 2 SPI";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ aliases {
+ ethernet1 = &qca7000;
+ };
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+ };
+
+ ssp2: ssp@80014000 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ qca7000: ethernet@0 {
+ compatible = "qca,qca7000";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qca7000_pins>;
+ reg = <0>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <8000000>;
+ };
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: led@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ qca7000_pins: qca7000@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */
+ MX28_PAD_LCD_D13__GPIO_1_13 /* QCA7K reset */
+ MX28_PAD_LCD_D14__GPIO_1_14 /* GPIO 0 */
+ MX28_PAD_LCD_D15__GPIO_1_15 /* GPIO 1 */
+ MX28_PAD_LCD_D18__GPIO_1_18 /* GPIO 2 */
+ MX28_PAD_LCD_D21__GPIO_1_21 /* GPIO 3 */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx@80040000 {
+ lradc@80050000 {
+ status = "okay";
+ };
+
+ duart: serial@80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy@8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ usb0: usb@80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet@800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH v2 8/9] ARM: dts: add support for I2SE Duckbill 2 SPI
@ 2017-01-22 22:22 ` Michael Heimpold
0 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: linux-arm-kernel
This machine is based on I2SE's Duckbill 2 board and is sold as part of I2SE's
PLC Bundle for IoT. This is a development kit for Homeplug Green PHY based
powerline products based on Qualcomms QCA7000 chip.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx28-duckbill-2-spi.dts | 199 +++++++++++++++++++++++++++++
2 files changed, 200 insertions(+)
create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-spi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d7fcb4dc..d2d2486 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -478,6 +478,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-duckbill-2-485.dts \
imx28-duckbill-2.dtb \
imx28-duckbill-2-enocean.dts \
+ imx28-duckbill-2-spi.dts \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
imx28-eukrea-mbmx287lc.dtb \
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
new file mode 100644
index 0000000..738eaa7
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
@@ -0,0 +1,199 @@
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill 2 SPI";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ aliases {
+ ethernet1 = &qca7000;
+ };
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb at 80000000 {
+ apbh at 80000000 {
+ ssp0: ssp at 80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+ };
+
+ ssp2: ssp at 80014000 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ qca7000: ethernet at 0 {
+ compatible = "qca,qca7000";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qca7000_pins>;
+ reg = <0>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <8000000>;
+ };
+ };
+
+ pinctrl at 80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: led at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ qca7000_pins: qca7000 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */
+ MX28_PAD_LCD_D13__GPIO_1_13 /* QCA7K reset */
+ MX28_PAD_LCD_D14__GPIO_1_14 /* GPIO 0 */
+ MX28_PAD_LCD_D15__GPIO_1_15 /* GPIO 1 */
+ MX28_PAD_LCD_D18__GPIO_1_18 /* GPIO 2 */
+ MX28_PAD_LCD_D21__GPIO_1_21 /* GPIO 3 */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx at 80040000 {
+ lradc at 80050000 {
+ status = "okay";
+ };
+
+ duart: serial at 80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy at 8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb at 80080000 {
+ usb0: usb at 80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet at 800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 36+ messages in thread[parent not found: <1485123764-14754-9-git-send-email-mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>]
* Re: [PATCH v2 8/9] ARM: dts: add support for I2SE Duckbill 2 SPI
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-23 17:16 ` Stefan Wahren
-1 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:16 UTC (permalink / raw)
To: Michael Heimpold, shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Fabio Estevam
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> This machine is based on I2SE's Duckbill 2 board and is sold as part of I2SE's
> PLC Bundle for IoT. This is a development kit for Homeplug Green PHY based
> powerline products based on Qualcomms QCA7000 chip.
>
> Signed-off-by: Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
> Cc: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx28-duckbill-2-spi.dts | 199 +++++++++++++++++++++++++++++
> 2 files changed, 200 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-spi.dts
>
...
> diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
> new file mode 100644
> index 0000000..738eaa7
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
> @@ -0,0 +1,199 @@
> +/*
> + * Copyright (C) 2015-2017 I2SE GmbH <info-eS4NqCHxEME@public.gmane.org>
> + * Copyright (C) 2016 Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "imx28.dtsi"
> +
> +/ {
> + model = "I2SE Duckbill 2 SPI";
> + compatible = "i2se,duckbill", "fsl,imx28";
> +
> + aliases {
> + ethernet1 = &qca7000;
> + };
> +
> + memory {
> + reg = <0x40000000 0x08000000>;
> + };
> +
> + apb@80000000 {
> + apbh@80000000 {
> + ssp0: ssp@80010000 {
> + compatible = "fsl,imx28-mmc";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_8bit_pins_a
> + &mmc0_cd_cfg &mmc0_sck_cfg>;
> + bus-width = <8>;
> + vmmc-supply = <®_3p3v>;
> + status = "okay";
> + non-removable;
> + };
> +
> + ssp2: ssp@80014000 {
> + compatible = "fsl,imx28-spi";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2_pins_a>;
> + status = "okay";
> +
> + qca7000: ethernet@0 {
> + compatible = "qca,qca7000";
> + pinctrl-names = "default";
> + pinctrl-0 = <&qca7000_pins>;
> + reg = <0>;
Just a nit. Please place the reg property before the compatible in order
to keep it like the others.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread* [PATCH v2 8/9] ARM: dts: add support for I2SE Duckbill 2 SPI
@ 2017-01-23 17:16 ` Stefan Wahren
0 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:16 UTC (permalink / raw)
To: linux-arm-kernel
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> This machine is based on I2SE's Duckbill 2 board and is sold as part of I2SE's
> PLC Bundle for IoT. This is a development kit for Homeplug Green PHY based
> powerline products based on Qualcomms QCA7000 chip.
>
> Signed-off-by: Michael Heimpold <mhei@heimpold.de>
> Cc: Stefan Wahren <stefan.wahren@i2se.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx28-duckbill-2-spi.dts | 199 +++++++++++++++++++++++++++++
> 2 files changed, 200 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-spi.dts
>
...
> diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
> new file mode 100644
> index 0000000..738eaa7
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
> @@ -0,0 +1,199 @@
> +/*
> + * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
> + * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "imx28.dtsi"
> +
> +/ {
> + model = "I2SE Duckbill 2 SPI";
> + compatible = "i2se,duckbill", "fsl,imx28";
> +
> + aliases {
> + ethernet1 = &qca7000;
> + };
> +
> + memory {
> + reg = <0x40000000 0x08000000>;
> + };
> +
> + apb at 80000000 {
> + apbh at 80000000 {
> + ssp0: ssp at 80010000 {
> + compatible = "fsl,imx28-mmc";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_8bit_pins_a
> + &mmc0_cd_cfg &mmc0_sck_cfg>;
> + bus-width = <8>;
> + vmmc-supply = <®_3p3v>;
> + status = "okay";
> + non-removable;
> + };
> +
> + ssp2: ssp at 80014000 {
> + compatible = "fsl,imx28-spi";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2_pins_a>;
> + status = "okay";
> +
> + qca7000: ethernet at 0 {
> + compatible = "qca,qca7000";
> + pinctrl-names = "default";
> + pinctrl-0 = <&qca7000_pins>;
> + reg = <0>;
Just a nit. Please place the reg property before the compatible in order
to keep it like the others.
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 9/9] Documentation: DT: add entries for I2SE boards
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-22 22:22 ` Michael Heimpold
-1 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, stefan.wahren-eS4NqCHxEME,
Michael Heimpold
This patch adds the missing devicetree binding documentation for I2SE's
Duckbill and Duckbill 2 series boards.
Signed-off-by: Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
Cc: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
---
Documentation/devicetree/bindings/arm/i2se.txt | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/i2se.txt
diff --git a/Documentation/devicetree/bindings/arm/i2se.txt b/Documentation/devicetree/bindings/arm/i2se.txt
new file mode 100644
index 0000000..9f30382
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/i2se.txt
@@ -0,0 +1,22 @@
+I2SE Device Tree Bindings
+-------------------------
+
+Duckbill Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
+
+Duckbill 2 Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
+
+Duckbill 2 485 Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
+
+Duckbill 2 EnOcean Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
+
+Duckbill 2 SPI Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v2 9/9] Documentation: DT: add entries for I2SE boards
@ 2017-01-22 22:22 ` Michael Heimpold
0 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-22 22:22 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds the missing devicetree binding documentation for I2SE's
Duckbill and Duckbill 2 series boards.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
---
Documentation/devicetree/bindings/arm/i2se.txt | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/i2se.txt
diff --git a/Documentation/devicetree/bindings/arm/i2se.txt b/Documentation/devicetree/bindings/arm/i2se.txt
new file mode 100644
index 0000000..9f30382
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/i2se.txt
@@ -0,0 +1,22 @@
+I2SE Device Tree Bindings
+-------------------------
+
+Duckbill Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
+
+Duckbill 2 Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
+
+Duckbill 2 485 Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
+
+Duckbill 2 EnOcean Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
+
+Duckbill 2 SPI Board
+Required root node properties:
+ - compatible = "i2se,duckbill", "fsl.imx28";
--
2.7.4
^ permalink raw reply related [flat|nested] 36+ messages in thread
[parent not found: <1485123764-14754-10-git-send-email-mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>]
* Re: [PATCH v2 9/9] Documentation: DT: add entries for I2SE boards
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-23 17:20 ` Stefan Wahren
-1 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:20 UTC (permalink / raw)
To: Michael Heimpold, shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Fabio Estevam
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> This patch adds the missing devicetree binding documentation for I2SE's
> Duckbill and Duckbill 2 series boards.
>
> Signed-off-by: Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org>
> Cc: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
> ---
> Documentation/devicetree/bindings/arm/i2se.txt | 22 ++++++++++++++++++++++
> 1 file changed, 22 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/i2se.txt
>
> diff --git a/Documentation/devicetree/bindings/arm/i2se.txt b/Documentation/devicetree/bindings/arm/i2se.txt
> new file mode 100644
> index 0000000..9f30382
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/i2se.txt
> @@ -0,0 +1,22 @@
> +I2SE Device Tree Bindings
> +-------------------------
> +
> +Duckbill Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
> +
> +Duckbill 2 Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
> +
> +Duckbill 2 485 Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
> +
> +Duckbill 2 EnOcean Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
> +
> +Duckbill 2 SPI Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
Please replace all fsl.imx28 with fsl,imx28
Maybe this patch should come before adding the Duckbill 2 board dts files.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 9/9] Documentation: DT: add entries for I2SE boards
@ 2017-01-23 17:20 ` Stefan Wahren
0 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:20 UTC (permalink / raw)
To: linux-arm-kernel
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> This patch adds the missing devicetree binding documentation for I2SE's
> Duckbill and Duckbill 2 series boards.
>
> Signed-off-by: Michael Heimpold <mhei@heimpold.de>
> Cc: Stefan Wahren <stefan.wahren@i2se.com>
> ---
> Documentation/devicetree/bindings/arm/i2se.txt | 22 ++++++++++++++++++++++
> 1 file changed, 22 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/i2se.txt
>
> diff --git a/Documentation/devicetree/bindings/arm/i2se.txt b/Documentation/devicetree/bindings/arm/i2se.txt
> new file mode 100644
> index 0000000..9f30382
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/i2se.txt
> @@ -0,0 +1,22 @@
> +I2SE Device Tree Bindings
> +-------------------------
> +
> +Duckbill Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
> +
> +Duckbill 2 Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
> +
> +Duckbill 2 485 Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
> +
> +Duckbill 2 EnOcean Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
> +
> +Duckbill 2 SPI Board
> +Required root node properties:
> + - compatible = "i2se,duckbill", "fsl.imx28";
Please replace all fsl.imx28 with fsl,imx28
Maybe this patch should come before adding the Duckbill 2 board dts files.
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v2 0/9] ARM: dts: support I2SE Duckbill devices
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-23 17:05 ` Stefan Wahren
-1 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:05 UTC (permalink / raw)
To: Michael Heimpold, shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, fabio.estevam-3arQi8VN3Tc
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> This series updates/adds Device Tree support for I2SE's Duckbill
> device family.
>
> The Duckbill devices are small, pen-drive sized boards based on
> NXP's i.MX28 SoC. While the initial variants (Duckbill series) were
> equipped with a micro SD card slot only, the latest generation
> (Duckbill 2 series) have an additional internal eMMC onboard.
>
> Both device generations consists of four "family members":
>
> - Duckbill/Duckbill 2: generic board, intended to be used as
> baseboard for custom designs and/or as development board
>
> - Duckbill EnOcean/Duckbill 2 EnOcean: come with an EnOcean
> daugther board equipped with the popular TCM310 module
>
> - Duckbill 485/Duckbill 2 485: as the name implies, these
> devices are intended to be used as Ethernet - RS485 converters
>
> - Duckbill SPI/Duckbill 2 SPI: not sold separately, but used
> in I2SE's development kits for Green PHY HomePlug Powerline
> communication
>
> Because the Duckbill series is EOL, this patch series only adds
> support for the latest Duckbill 2 series devices. However,
> support for the generic Duckbill board was already mainline,
> so update it to match vendor tree DT.
Acked-by: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
for patches 1,2,3,5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 0/9] ARM: dts: support I2SE Duckbill devices
@ 2017-01-23 17:05 ` Stefan Wahren
0 siblings, 0 replies; 36+ messages in thread
From: Stefan Wahren @ 2017-01-23 17:05 UTC (permalink / raw)
To: linux-arm-kernel
Am 22.01.2017 um 23:22 schrieb Michael Heimpold:
> This series updates/adds Device Tree support for I2SE's Duckbill
> device family.
>
> The Duckbill devices are small, pen-drive sized boards based on
> NXP's i.MX28 SoC. While the initial variants (Duckbill series) were
> equipped with a micro SD card slot only, the latest generation
> (Duckbill 2 series) have an additional internal eMMC onboard.
>
> Both device generations consists of four "family members":
>
> - Duckbill/Duckbill 2: generic board, intended to be used as
> baseboard for custom designs and/or as development board
>
> - Duckbill EnOcean/Duckbill 2 EnOcean: come with an EnOcean
> daugther board equipped with the popular TCM310 module
>
> - Duckbill 485/Duckbill 2 485: as the name implies, these
> devices are intended to be used as Ethernet - RS485 converters
>
> - Duckbill SPI/Duckbill 2 SPI: not sold separately, but used
> in I2SE's development kits for Green PHY HomePlug Powerline
> communication
>
> Because the Duckbill series is EOL, this patch series only adds
> support for the latest Duckbill 2 series devices. However,
> support for the generic Duckbill board was already mainline,
> so update it to match vendor tree DT.
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
for patches 1,2,3,5
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v2 0/9] ARM: dts: support I2SE Duckbill devices
2017-01-22 22:22 ` Michael Heimpold
@ 2017-01-23 18:18 ` Fabio Estevam
-1 siblings, 0 replies; 36+ messages in thread
From: Fabio Estevam @ 2017-01-23 18:18 UTC (permalink / raw)
To: Michael Heimpold
Cc: Shawn Guo, Sascha Hauer, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
Mark Rutland, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Stefan Wahren
Hi Michael,
On Sun, Jan 22, 2017 at 8:22 PM, Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org> wrote:
> - Duckbill 485/Duckbill 2 485: as the name implies, these
> devices are intended to be used as Ethernet - RS485 converters
Just curious: do you use mxs-auart to interface to a rs485
transceiver? If so, would you have mxs-auart patches that add rs485?
Thanks
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 0/9] ARM: dts: support I2SE Duckbill devices
@ 2017-01-23 18:18 ` Fabio Estevam
0 siblings, 0 replies; 36+ messages in thread
From: Fabio Estevam @ 2017-01-23 18:18 UTC (permalink / raw)
To: linux-arm-kernel
Hi Michael,
On Sun, Jan 22, 2017 at 8:22 PM, Michael Heimpold <mhei@heimpold.de> wrote:
> - Duckbill 485/Duckbill 2 485: as the name implies, these
> devices are intended to be used as Ethernet - RS485 converters
Just curious: do you use mxs-auart to interface to a rs485
transceiver? If so, would you have mxs-auart patches that add rs485?
Thanks
^ permalink raw reply [flat|nested] 36+ messages in thread
[parent not found: <CAOMZO5CbPPR7GSjUvPQaHGCTTiFw8PrQfiwa_j2x9+WyKuseZg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>]
* Re: [PATCH v2 0/9] ARM: dts: support I2SE Duckbill devices
2017-01-23 18:18 ` Fabio Estevam
@ 2017-01-24 6:44 ` Michael Heimpold
-1 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-24 6:44 UTC (permalink / raw)
To: Fabio Estevam
Cc: Shawn Guo, Sascha Hauer, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
Mark Rutland, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Stefan Wahren
Hi Fabio,
Zitat von Fabio Estevam <festevam-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>:
> Hi Michael,
>
> On Sun, Jan 22, 2017 at 8:22 PM, Michael Heimpold <mhei-Z/Lg1yOAjpkb1SvskN2V4Q@public.gmane.org> wrote:
>
>> - Duckbill 485/Duckbill 2 485: as the name implies, these
>> devices are intended to be used as Ethernet - RS485 converters
>
> Just curious: do you use mxs-auart to interface to a rs485
> transceiver? If so, would you have mxs-auart patches that add rs485?
Due to the lack of hardware support in mxs-auart for rs485, we decided
to use a more expensive hardware transceiver with auto direction feature.
So the rs485 is (mostly) transparent for upper layers.
Regards,
Michael
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v2 0/9] ARM: dts: support I2SE Duckbill devices
@ 2017-01-24 6:44 ` Michael Heimpold
0 siblings, 0 replies; 36+ messages in thread
From: Michael Heimpold @ 2017-01-24 6:44 UTC (permalink / raw)
To: linux-arm-kernel
Hi Fabio,
Zitat von Fabio Estevam <festevam@gmail.com>:
> Hi Michael,
>
> On Sun, Jan 22, 2017 at 8:22 PM, Michael Heimpold <mhei@heimpold.de> wrote:
>
>> - Duckbill 485/Duckbill 2 485: as the name implies, these
>> devices are intended to be used as Ethernet - RS485 converters
>
> Just curious: do you use mxs-auart to interface to a rs485
> transceiver? If so, would you have mxs-auart patches that add rs485?
Due to the lack of hardware support in mxs-auart for rs485, we decided
to use a more expensive hardware transceiver with auto direction feature.
So the rs485 is (mostly) transparent for upper layers.
Regards,
Michael
^ permalink raw reply [flat|nested] 36+ messages in thread