Re: [PATCH v5 00/13] Canaan devicetree fixes

[Palmer Dabbelt <palmer@rivosinc.com>]

On Tue, 05 Jul 2022 14:52:01 PDT (-0700), mail@conchuod.ie wrote:
> From: Conor Dooley <conor.dooley@microchip.com>
>
> Hey all,
> This series should rid us of dtbs_check errors for the RISC-V Canaan k210
> based boards. To make keeping it that way a little easier, I changed the
> Canaan devicetree Makefile so that it would build all of the devicetrees
> in the directory if SOC_CANAAN.
>
> I *DO NOT* have any Canaan hardware so I have not tested any of this in
> action. Since I sent v1, I tried to buy some since it's cheap - but could
> out of the limited stockists none seemed to want to deliver to Ireland :(
> I based the series on next-20220617.
>
> Thanks,
> Conor.
>
> Changes since v4:
> - add Rob's tags from v3
> - sram: rephrase the binding description
> - ASoC: dropped the applied binding
>
> Changes since v3:
> - dts: drop the bogus "regs" property pointed out by Niklas
> - dma/timer: add Serge's reviews (and expand on the dma interrupt
>   description)
> - dts: add Niklas' T-b where I felt it was suitable. lmk if you think it
>   applies more broadly
> - spi: drop the applied spi dt-binding change. Thanks Mark.
>
> Changes since v2:
> - i2s: added clocks maxItems
> - dma: unconditionally extended the interrupts & dropped canaan
>   compatible
> - timer: as per Sergey, split the timer dts nodes in 2 & drop the
>   binding patch
> - ili9341: add a canaan specific compatible to the binding and dts
>
> Changes since v1:
> - I added a new dt node & compatible for the SRAM memory controller due
>   Damien's wish to preserve the inter-op with U-Boot.
> - The dw-apb-ssi binding now uses the default rx/tx widths
> - A new patch fixes bus {ranges,reg} warnings
> - Rearranged the patches in a slightly more logical order
>
> Conor Dooley (13):
>   dt-bindings: display: convert ilitek,ili9341.txt to dt-schema
>   dt-bindings: display: ili9341: document canaan kd233's lcd
>   dt-bindings: dma: dw-axi-dmac: extend the number of interrupts
>   dt-bindings: memory-controllers: add canaan k210 sram controller
>   riscv: dts: canaan: fix the k210's memory node
>   riscv: dts: canaan: fix the k210's timer nodes
>   riscv: dts: canaan: fix mmc node names
>   riscv: dts: canaan: fix kd233 display spi frequency
>   riscv: dts: canaan: use custom compatible for k210 i2s
>   riscv: dts: canaan: remove spi-max-frequency from controllers
>   riscv: dts: canaan: fix bus {ranges,reg} warnings
>   riscv: dts: canaan: add specific compatible for kd233's LCD
>   riscv: dts: canaan: build all devicetress if SOC_CANAAN
>
>  .../bindings/display/ilitek,ili9341.txt       | 27 -------
>  .../display/panel/ilitek,ili9341.yaml         | 49 +++++++++----
>  .../bindings/dma/snps,dw-axi-dmac.yaml        |  7 +-
>  .../memory-controllers/canaan,k210-sram.yaml  | 52 +++++++++++++
>  arch/riscv/boot/dts/canaan/Makefile           | 10 ++-
>  arch/riscv/boot/dts/canaan/canaan_kd233.dts   |  6 +-
>  arch/riscv/boot/dts/canaan/k210.dtsi          | 73 +++++++++++++------
>  .../riscv/boot/dts/canaan/sipeed_maix_bit.dts |  2 +-
>  .../boot/dts/canaan/sipeed_maix_dock.dts      |  2 +-
>  arch/riscv/boot/dts/canaan/sipeed_maix_go.dts |  2 +-
>  .../boot/dts/canaan/sipeed_maixduino.dts      |  2 +-
>  11 files changed, 159 insertions(+), 73 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/ilitek,ili9341.txt
>  create mode 100644 Documentation/devicetree/bindings/memory-controllers/canaan,k210-sram.yaml

I'm trying to sort out how to merge this one.  I'm not opposed to taking 
it through the RISC-V tree as Rob's reviewed/acked the bindings, but 
just figured I'd say something before putting anything on for-next to 
try and minimize confusion.

Unless I'm missing something it's just patch 3 that's been taken so far, 
via Vinod's tree.  I've dropped that one and put the rest on 
palmer/riscv-canaan_dt_schema, if that looks good then I'll take it into 
riscv/for-next when this loops back to the top of my queue.

Thanks!