* [alsa-devel] [RFC PATCH] ASoC: ams-delta: Take control over audio mute GPIO pins
@ 2019-09-07 11:16 Janusz Krzysztofik
2019-09-09 7:56 ` Peter Ujfalusi
2019-09-09 10:07 ` [alsa-devel] Applied "ASoC: ams-delta: Take control over audio mute GPIO pins" to the asoc tree Mark Brown
0 siblings, 2 replies; 3+ messages in thread
From: Janusz Krzysztofik @ 2019-09-07 11:16 UTC (permalink / raw)
To: Mark Brown, Liam Girdwood
Cc: alsa-devel, Aaro Koskinen, Tony Lindgren, Janusz Krzysztofik,
Peter Ujfalusi, linux-omap
Since commit 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. It has been discovered that
believed to be unused GPIO pins "hookflash1" and "hookflash2" need to be
set low for audible sound in handsfree and handset mode respectively.
According to Amstrad E3 wiki, the purpose of both pins hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on them when the phone was taken off hook or recall was pressed.
With the current findings, we can assume the pins provide a kind of
audio mute function, separately for handset and handsfree operation
modes.
Commit 2afdb4c41d78 ("ARM: OMAP1: ams-delta: Fix audio permanently
muted") attempted to fix the issue temporarily by hogging the GPIO pin
"hookflash1" renamed to "audio_mute", however the fix occurred
incomplete as it restored audible sound only for handsfree mode.
Stop hogging that pin, rename the pins to "handsfree_mute" and
"handset_mute" respectively and implement appropriate DAPM event
callbacks for "Speaker" and "Earpiece" DAPM widgets.
Fixes: 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
---
arch/arm/mach-omap1/board-ams-delta.c | 10 +++++----
sound/soc/ti/ams-delta.c | 31 +++++++++++++++++++++++++--
2 files changed, 35 insertions(+), 6 deletions(-)
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index e47a6fbcfd6e..a2aa7a12b374 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -246,8 +246,8 @@ static struct platform_device latch2_gpio_device = {
#define LATCH2_PIN_SCARD_CMDVCC 11
#define LATCH2_PIN_MODEM_NRESET 12
#define LATCH2_PIN_MODEM_CODEC 13
-#define LATCH2_PIN_AUDIO_MUTE 14
-#define LATCH2_PIN_HOOKFLASH 15
+#define LATCH2_PIN_HANDSFREE_MUTE 14
+#define LATCH2_PIN_HANDSET_MUTE 15
static struct regulator_consumer_supply modem_nreset_consumers[] = {
REGULATOR_SUPPLY("RESET#", "serial8250.1"),
@@ -476,6 +476,10 @@ static struct gpiod_lookup_table ams_delta_audio_gpio_table = {
"hook_switch", 0),
GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_MODEM_CODEC,
"modem_codec", 0),
+ GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_HANDSFREE_MUTE,
+ "handsfree_mute", 0),
+ GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_HANDSET_MUTE,
+ "handset_mute", 0),
{ },
},
};
@@ -590,8 +594,6 @@ static int gpiochip_match_by_label(struct gpio_chip *chip, void *data)
static struct gpiod_hog ams_delta_gpio_hogs[] = {
GPIO_HOG(LATCH2_LABEL, LATCH2_PIN_KEYBRD_DATAOUT, "keybrd_dataout",
GPIO_ACTIVE_HIGH, GPIOD_OUT_LOW),
- GPIO_HOG(LATCH2_LABEL, LATCH2_PIN_AUDIO_MUTE, "audio_mute",
- GPIO_ACTIVE_HIGH, GPIOD_OUT_LOW),
{},
};
diff --git a/sound/soc/ti/ams-delta.c b/sound/soc/ti/ams-delta.c
index dee8fc70a64f..8e2fb81ad05c 100644
--- a/sound/soc/ti/ams-delta.c
+++ b/sound/soc/ti/ams-delta.c
@@ -23,14 +23,31 @@
#include "omap-mcbsp.h"
#include "../codecs/cx20442.h"
+static struct gpio_desc *handset_mute;
+static struct gpio_desc *handsfree_mute;
+
+static int ams_delta_event_handset(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *k, int event)
+{
+ gpiod_set_value_cansleep(handset_mute, !SND_SOC_DAPM_EVENT_ON(event));
+ return 0;
+}
+
+static int ams_delta_event_handsfree(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *k, int event)
+{
+ gpiod_set_value_cansleep(handsfree_mute, !SND_SOC_DAPM_EVENT_ON(event));
+ return 0;
+}
+
/* Board specific DAPM widgets */
static const struct snd_soc_dapm_widget ams_delta_dapm_widgets[] = {
/* Handset */
SND_SOC_DAPM_MIC("Mouthpiece", NULL),
- SND_SOC_DAPM_HP("Earpiece", NULL),
+ SND_SOC_DAPM_HP("Earpiece", ams_delta_event_handset),
/* Handsfree/Speakerphone */
SND_SOC_DAPM_MIC("Microphone", NULL),
- SND_SOC_DAPM_SPK("Speaker", NULL),
+ SND_SOC_DAPM_SPK("Speaker", ams_delta_event_handsfree),
};
/* How they are connected to codec pins */
@@ -542,6 +559,16 @@ static int ams_delta_probe(struct platform_device *pdev)
card->dev = &pdev->dev;
+ handset_mute = devm_gpiod_get(card->dev, "handset_mute",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(handset_mute))
+ return PTR_ERR(handset_mute);
+
+ handsfree_mute = devm_gpiod_get(card->dev, "handsfree_mute",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(handsfree_mute))
+ return PTR_ERR(handsfree_mute);
+
ret = snd_soc_register_card(card);
if (ret) {
dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret);
--
2.21.0
_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [alsa-devel] [RFC PATCH] ASoC: ams-delta: Take control over audio mute GPIO pins
2019-09-07 11:16 [alsa-devel] [RFC PATCH] ASoC: ams-delta: Take control over audio mute GPIO pins Janusz Krzysztofik
@ 2019-09-09 7:56 ` Peter Ujfalusi
2019-09-09 10:07 ` [alsa-devel] Applied "ASoC: ams-delta: Take control over audio mute GPIO pins" to the asoc tree Mark Brown
1 sibling, 0 replies; 3+ messages in thread
From: Peter Ujfalusi @ 2019-09-09 7:56 UTC (permalink / raw)
To: Janusz Krzysztofik, Mark Brown, Liam Girdwood
Cc: Tony Lindgren, alsa-devel, linux-omap, Aaro Koskinen
On 07/09/2019 14.16, Janusz Krzysztofik wrote:
> Since commit 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused
> GPIOs"), on-board audio has appeared muted. It has been discovered that
> believed to be unused GPIO pins "hookflash1" and "hookflash2" need to be
> set low for audible sound in handsfree and handset mode respectively.
>
> According to Amstrad E3 wiki, the purpose of both pins hasn't been
> clearly identified. Original Amstrad software used to produce a high
> pulse on them when the phone was taken off hook or recall was pressed.
> With the current findings, we can assume the pins provide a kind of
> audio mute function, separately for handset and handsfree operation
> modes.
>
> Commit 2afdb4c41d78 ("ARM: OMAP1: ams-delta: Fix audio permanently
> muted") attempted to fix the issue temporarily by hogging the GPIO pin
> "hookflash1" renamed to "audio_mute", however the fix occurred
> incomplete as it restored audible sound only for handsfree mode.
>
> Stop hogging that pin, rename the pins to "handsfree_mute" and
> "handset_mute" respectively and implement appropriate DAPM event
> callbacks for "Speaker" and "Earpiece" DAPM widgets.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
> Fixes: 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
> ---
> arch/arm/mach-omap1/board-ams-delta.c | 10 +++++----
> sound/soc/ti/ams-delta.c | 31 +++++++++++++++++++++++++--
> 2 files changed, 35 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
> index e47a6fbcfd6e..a2aa7a12b374 100644
> --- a/arch/arm/mach-omap1/board-ams-delta.c
> +++ b/arch/arm/mach-omap1/board-ams-delta.c
> @@ -246,8 +246,8 @@ static struct platform_device latch2_gpio_device = {
> #define LATCH2_PIN_SCARD_CMDVCC 11
> #define LATCH2_PIN_MODEM_NRESET 12
> #define LATCH2_PIN_MODEM_CODEC 13
> -#define LATCH2_PIN_AUDIO_MUTE 14
> -#define LATCH2_PIN_HOOKFLASH 15
> +#define LATCH2_PIN_HANDSFREE_MUTE 14
> +#define LATCH2_PIN_HANDSET_MUTE 15
>
> static struct regulator_consumer_supply modem_nreset_consumers[] = {
> REGULATOR_SUPPLY("RESET#", "serial8250.1"),
> @@ -476,6 +476,10 @@ static struct gpiod_lookup_table ams_delta_audio_gpio_table = {
> "hook_switch", 0),
> GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_MODEM_CODEC,
> "modem_codec", 0),
> + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_HANDSFREE_MUTE,
> + "handsfree_mute", 0),
> + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_HANDSET_MUTE,
> + "handset_mute", 0),
> { },
> },
> };
> @@ -590,8 +594,6 @@ static int gpiochip_match_by_label(struct gpio_chip *chip, void *data)
> static struct gpiod_hog ams_delta_gpio_hogs[] = {
> GPIO_HOG(LATCH2_LABEL, LATCH2_PIN_KEYBRD_DATAOUT, "keybrd_dataout",
> GPIO_ACTIVE_HIGH, GPIOD_OUT_LOW),
> - GPIO_HOG(LATCH2_LABEL, LATCH2_PIN_AUDIO_MUTE, "audio_mute",
> - GPIO_ACTIVE_HIGH, GPIOD_OUT_LOW),
> {},
> };
>
> diff --git a/sound/soc/ti/ams-delta.c b/sound/soc/ti/ams-delta.c
> index dee8fc70a64f..8e2fb81ad05c 100644
> --- a/sound/soc/ti/ams-delta.c
> +++ b/sound/soc/ti/ams-delta.c
> @@ -23,14 +23,31 @@
> #include "omap-mcbsp.h"
> #include "../codecs/cx20442.h"
>
> +static struct gpio_desc *handset_mute;
> +static struct gpio_desc *handsfree_mute;
> +
> +static int ams_delta_event_handset(struct snd_soc_dapm_widget *w,
> + struct snd_kcontrol *k, int event)
> +{
> + gpiod_set_value_cansleep(handset_mute, !SND_SOC_DAPM_EVENT_ON(event));
> + return 0;
> +}
> +
> +static int ams_delta_event_handsfree(struct snd_soc_dapm_widget *w,
> + struct snd_kcontrol *k, int event)
> +{
> + gpiod_set_value_cansleep(handsfree_mute, !SND_SOC_DAPM_EVENT_ON(event));
> + return 0;
> +}
> +
> /* Board specific DAPM widgets */
> static const struct snd_soc_dapm_widget ams_delta_dapm_widgets[] = {
> /* Handset */
> SND_SOC_DAPM_MIC("Mouthpiece", NULL),
> - SND_SOC_DAPM_HP("Earpiece", NULL),
> + SND_SOC_DAPM_HP("Earpiece", ams_delta_event_handset),
> /* Handsfree/Speakerphone */
> SND_SOC_DAPM_MIC("Microphone", NULL),
> - SND_SOC_DAPM_SPK("Speaker", NULL),
> + SND_SOC_DAPM_SPK("Speaker", ams_delta_event_handsfree),
> };
>
> /* How they are connected to codec pins */
> @@ -542,6 +559,16 @@ static int ams_delta_probe(struct platform_device *pdev)
>
> card->dev = &pdev->dev;
>
> + handset_mute = devm_gpiod_get(card->dev, "handset_mute",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(handset_mute))
> + return PTR_ERR(handset_mute);
> +
> + handsfree_mute = devm_gpiod_get(card->dev, "handsfree_mute",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(handsfree_mute))
> + return PTR_ERR(handsfree_mute);
> +
> ret = snd_soc_register_card(card);
> if (ret) {
> dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret);
>
- Péter
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel
^ permalink raw reply [flat|nested] 3+ messages in thread* [alsa-devel] Applied "ASoC: ams-delta: Take control over audio mute GPIO pins" to the asoc tree
2019-09-07 11:16 [alsa-devel] [RFC PATCH] ASoC: ams-delta: Take control over audio mute GPIO pins Janusz Krzysztofik
2019-09-09 7:56 ` Peter Ujfalusi
@ 2019-09-09 10:07 ` Mark Brown
1 sibling, 0 replies; 3+ messages in thread
From: Mark Brown @ 2019-09-09 10:07 UTC (permalink / raw)
To: Janusz Krzysztofik
Cc: alsa-devel, Aaro Koskinen, Tony Lindgren, Liam Girdwood,
Peter Ujfalusi, Mark Brown, linux-omap
The patch
ASoC: ams-delta: Take control over audio mute GPIO pins
has been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-5.3
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
From 73681f4f1426847b421649c6aa6c2dc303acc7c8 Mon Sep 17 00:00:00 2001
From: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Date: Sat, 7 Sep 2019 13:16:50 +0200
Subject: [PATCH] ASoC: ams-delta: Take control over audio mute GPIO pins
Since commit 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. It has been discovered that
believed to be unused GPIO pins "hookflash1" and "hookflash2" need to be
set low for audible sound in handsfree and handset mode respectively.
According to Amstrad E3 wiki, the purpose of both pins hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on them when the phone was taken off hook or recall was pressed.
With the current findings, we can assume the pins provide a kind of
audio mute function, separately for handset and handsfree operation
modes.
Commit 2afdb4c41d78 ("ARM: OMAP1: ams-delta: Fix audio permanently
muted") attempted to fix the issue temporarily by hogging the GPIO pin
"hookflash1" renamed to "audio_mute", however the fix occurred
incomplete as it restored audible sound only for handsfree mode.
Stop hogging that pin, rename the pins to "handsfree_mute" and
"handset_mute" respectively and implement appropriate DAPM event
callbacks for "Speaker" and "Earpiece" DAPM widgets.
Fixes: 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190907111650.15440-1-jmkrzyszt@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
---
arch/arm/mach-omap1/board-ams-delta.c | 10 +++++----
sound/soc/ti/ams-delta.c | 31 +++++++++++++++++++++++++--
2 files changed, 35 insertions(+), 6 deletions(-)
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 36498ea1b2f3..c2affc727967 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -245,8 +245,8 @@ static struct platform_device latch2_gpio_device = {
#define LATCH2_PIN_SCARD_CMDVCC 11
#define LATCH2_PIN_MODEM_NRESET 12
#define LATCH2_PIN_MODEM_CODEC 13
-#define LATCH2_PIN_AUDIO_MUTE 14
-#define LATCH2_PIN_HOOKFLASH 15
+#define LATCH2_PIN_HANDSFREE_MUTE 14
+#define LATCH2_PIN_HANDSET_MUTE 15
static struct regulator_consumer_supply modem_nreset_consumers[] = {
REGULATOR_SUPPLY("RESET#", "serial8250.1"),
@@ -475,6 +475,10 @@ static struct gpiod_lookup_table ams_delta_audio_gpio_table = {
"hook_switch", 0),
GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_MODEM_CODEC,
"modem_codec", 0),
+ GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_HANDSFREE_MUTE,
+ "handsfree_mute", 0),
+ GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_HANDSET_MUTE,
+ "handset_mute", 0),
{ },
},
};
@@ -589,8 +593,6 @@ static int gpiochip_match_by_label(struct gpio_chip *chip, void *data)
static struct gpiod_hog ams_delta_gpio_hogs[] = {
GPIO_HOG(LATCH2_LABEL, LATCH2_PIN_KEYBRD_DATAOUT, "keybrd_dataout",
GPIO_ACTIVE_HIGH, GPIOD_OUT_LOW),
- GPIO_HOG(LATCH2_LABEL, LATCH2_PIN_AUDIO_MUTE, "audio_mute",
- GPIO_ACTIVE_HIGH, GPIOD_OUT_LOW),
{},
};
diff --git a/sound/soc/ti/ams-delta.c b/sound/soc/ti/ams-delta.c
index dee8fc70a64f..8e2fb81ad05c 100644
--- a/sound/soc/ti/ams-delta.c
+++ b/sound/soc/ti/ams-delta.c
@@ -23,14 +23,31 @@
#include "omap-mcbsp.h"
#include "../codecs/cx20442.h"
+static struct gpio_desc *handset_mute;
+static struct gpio_desc *handsfree_mute;
+
+static int ams_delta_event_handset(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *k, int event)
+{
+ gpiod_set_value_cansleep(handset_mute, !SND_SOC_DAPM_EVENT_ON(event));
+ return 0;
+}
+
+static int ams_delta_event_handsfree(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *k, int event)
+{
+ gpiod_set_value_cansleep(handsfree_mute, !SND_SOC_DAPM_EVENT_ON(event));
+ return 0;
+}
+
/* Board specific DAPM widgets */
static const struct snd_soc_dapm_widget ams_delta_dapm_widgets[] = {
/* Handset */
SND_SOC_DAPM_MIC("Mouthpiece", NULL),
- SND_SOC_DAPM_HP("Earpiece", NULL),
+ SND_SOC_DAPM_HP("Earpiece", ams_delta_event_handset),
/* Handsfree/Speakerphone */
SND_SOC_DAPM_MIC("Microphone", NULL),
- SND_SOC_DAPM_SPK("Speaker", NULL),
+ SND_SOC_DAPM_SPK("Speaker", ams_delta_event_handsfree),
};
/* How they are connected to codec pins */
@@ -542,6 +559,16 @@ static int ams_delta_probe(struct platform_device *pdev)
card->dev = &pdev->dev;
+ handset_mute = devm_gpiod_get(card->dev, "handset_mute",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(handset_mute))
+ return PTR_ERR(handset_mute);
+
+ handsfree_mute = devm_gpiod_get(card->dev, "handsfree_mute",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(handsfree_mute))
+ return PTR_ERR(handsfree_mute);
+
ret = snd_soc_register_card(card);
if (ret) {
dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret);
--
2.20.1
_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-09-09 10:53 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-09-07 11:16 [alsa-devel] [RFC PATCH] ASoC: ams-delta: Take control over audio mute GPIO pins Janusz Krzysztofik
2019-09-09 7:56 ` Peter Ujfalusi
2019-09-09 10:07 ` [alsa-devel] Applied "ASoC: ams-delta: Take control over audio mute GPIO pins" to the asoc tree Mark Brown
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).