Alsa-Devel Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v2 0/7] Add support for Rpi4b + Cirrus Lochnagar2 and CS47L15
@ 2020-10-16 17:35 Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 1/7] of: base: Add of_count_phandle_with_fixed_args() Richard Fitzgerald
                   ` (6 more replies)
  0 siblings, 7 replies; 8+ messages in thread
From: Richard Fitzgerald @ 2020-10-16 17:35 UTC (permalink / raw)
  To: broonie, robh+dt, nsaenzjulienne
  Cc: devicetree, alsa-devel, patches, linux-kernel,
	Richard Fitzgerald, linux-rpi-kernel, linux-arm-kernel

This set of patches provides support for using the Raspberry Pi 4b with
a Cirrus Logic Lochnagar 2 audio development platform plus Cirrus Logic
CS47L15 codec.

Patches are needed to audio-graph-card to enable support for setting the
component sysclks and plls. The codec sysclks and plls cannot be placed
under the clock framwork because they are I2C/SPI-connected peripherals
and access to the registers would cause a nested get of the I2C/SPI bus
clock. The clock framework does not support this and it would result in
a deadlock.

Richard Fitzgerald (7):
  of: base: Add of_count_phandle_with_fixed_args()
  ASoC: audio-graph-card: Add plls and sysclks DT bindings
  ASoC: audio-graph-card: Support setting component plls and sysclks
  ASoC: arizona: Allow codecs to be selected from kernel config
  ASoC: madera: Allow codecs to be selected from kernel config
  ARM: dts: Add dts for RPi4b + Cirrus Logic Lochnagar2 + CS47L15
  MAINTAINERS: Add dts for Cirrus Logic Lochnagar on RPi4

 .../bindings/sound/audio-graph-card.txt       |  44 ++++
 MAINTAINERS                                   |   1 +
 arch/arm/boot/dts/Makefile                    |   1 +
 ...bcm2711-rpi4b-cirrus-lochnagar-cs47l15.dts | 166 +++++++++++++++
 .../dts/bcm2711-rpi4b-cirrus-lochnagar.dtsi   | 201 ++++++++++++++++++
 drivers/of/base.c                             |  73 +++++--
 include/linux/of.h                            |   9 +
 include/sound/simple_card_utils.h             |  24 +++
 sound/soc/codecs/Kconfig                      |  18 +-
 sound/soc/generic/audio-graph-card.c          |  16 +-
 sound/soc/generic/simple-card-utils.c         | 184 ++++++++++++++++
 11 files changed, 703 insertions(+), 34 deletions(-)
 create mode 100644 arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar-cs47l15.dts
 create mode 100644 arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar.dtsi

-- 
2.20.1


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v2 1/7] of: base: Add of_count_phandle_with_fixed_args()
  2020-10-16 17:35 [PATCH v2 0/7] Add support for Rpi4b + Cirrus Lochnagar2 and CS47L15 Richard Fitzgerald
@ 2020-10-16 17:35 ` Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 2/7] ASoC: audio-graph-card: Add plls and sysclks DT bindings Richard Fitzgerald
                   ` (5 subsequent siblings)
  6 siblings, 0 replies; 8+ messages in thread
From: Richard Fitzgerald @ 2020-10-16 17:35 UTC (permalink / raw)
  To: broonie, robh+dt, nsaenzjulienne
  Cc: devicetree, alsa-devel, patches, linux-kernel,
	Richard Fitzgerald, linux-rpi-kernel, linux-arm-kernel

Add an equivalent of of_count_phandle_with_args() for fixed argument
sets, to pair with of_parse_phandle_with_fixed_args().

The existing of_count_phandle_with_args() is modified to be a
private function that handles both cases and the public functions
are trivial wrappers round that.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
---
 drivers/of/base.c  | 73 +++++++++++++++++++++++++++++++---------------
 include/linux/of.h |  9 ++++++
 2 files changed, 59 insertions(+), 23 deletions(-)

diff --git a/drivers/of/base.c b/drivers/of/base.c
index 161a23631472..c5ff2524bf40 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -1720,34 +1720,22 @@ int of_parse_phandle_with_fixed_args(const struct device_node *np,
 }
 EXPORT_SYMBOL(of_parse_phandle_with_fixed_args);
 
-/**
- * of_count_phandle_with_args() - Find the number of phandles references in a property
- * @np:		pointer to a device tree node containing a list
- * @list_name:	property name that contains a list
- * @cells_name:	property name that specifies phandles' arguments count
- *
- * Returns the number of phandle + argument tuples within a property. It
- * is a typical pattern to encode a list of phandle and variable
- * arguments into a single property. The number of arguments is encoded
- * by a property in the phandle-target node. For example, a gpios
- * property would contain a list of GPIO specifies consisting of a
- * phandle and 1 or more arguments. The number of arguments are
- * determined by the #gpio-cells property in the node pointed to by the
- * phandle.
- */
-int of_count_phandle_with_args(const struct device_node *np, const char *list_name,
-				const char *cells_name)
+static int __of_count_phandle_with_args(const struct device_node *np,
+					const char *list_name,
+					const char *cells_name,
+					int cells_count)
 {
 	struct of_phandle_iterator it;
 	int rc, cur_index = 0;
 
 	/*
-	 * If cells_name is NULL we assume a cell count of 0. This makes
-	 * counting the phandles trivial as each 32bit word in the list is a
-	 * phandle and no arguments are to consider. So we don't iterate through
-	 * the list but just use the length to determine the phandle count.
+	 * If cells_count < 0 and cells_name is NULL we assume a cell count
+	 * of 0. A zero cell count makes counting the phandles trivial as each
+	 * 32bit word in the list is a phandle and no arguments are to consider.
+	 * So we don't iterate through the list but just use the length to
+	 * determine the phandle count.
 	 */
-	if (!cells_name) {
+	if ((cells_count < 0 && !cells_name) || cells_count == 0) {
 		const __be32 *list;
 		int size;
 
@@ -1758,7 +1746,7 @@ int of_count_phandle_with_args(const struct device_node *np, const char *list_na
 		return size / sizeof(*list);
 	}
 
-	rc = of_phandle_iterator_init(&it, np, list_name, cells_name, -1);
+	rc = of_phandle_iterator_init(&it, np, list_name, cells_name, cells_count);
 	if (rc)
 		return rc;
 
@@ -1770,8 +1758,47 @@ int of_count_phandle_with_args(const struct device_node *np, const char *list_na
 
 	return cur_index;
 }
+
+/**
+ * of_count_phandle_with_args() - Find the number of phandles references in a property
+ * @np:		pointer to a device tree node containing a list
+ * @list_name:	property name that contains a list
+ * @cells_name:	property name that specifies phandles' arguments count
+ *
+ * Returns the number of phandle + argument tuples within a property. It
+ * is a typical pattern to encode a list of phandle and variable
+ * arguments into a single property. The number of arguments is encoded
+ * by a property in the phandle-target node. For example, a gpios
+ * property would contain a list of GPIO specifies consisting of a
+ * phandle and 1 or more arguments. The number of arguments are
+ * determined by the #gpio-cells property in the node pointed to by the
+ * phandle.
+ */
+int of_count_phandle_with_args(const struct device_node *np, const char *list_name,
+				const char *cells_name)
+{
+	return __of_count_phandle_with_args(np, list_name, cells_name, -1);
+}
 EXPORT_SYMBOL(of_count_phandle_with_args);
 
+/**
+ * of_count_phandle_with_fixed_args() - Find the number of phandles references in a property
+ * @np:		pointer to a device tree node containing a list
+ * @list_name:	property name that contains a list
+ * @cell_count: number of argument cells following the phandle
+ *
+ * Returns the number of phandle + argument tuples within a property. It
+ * is a typical pattern to encode a list of phandle and variable
+ * arguments into a single property.
+ */
+int of_count_phandle_with_fixed_args(const struct device_node *np,
+				     const char *list_name,
+				     int cells_count)
+{
+	return __of_count_phandle_with_args(np, list_name, NULL, cells_count);
+}
+EXPORT_SYMBOL(of_count_phandle_with_fixed_args);
+
 /**
  * __of_add_property - Add a property to a node without lock operations
  */
diff --git a/include/linux/of.h b/include/linux/of.h
index 481ec0467285..4382a8946310 100644
--- a/include/linux/of.h
+++ b/include/linux/of.h
@@ -377,6 +377,8 @@ extern int of_parse_phandle_with_fixed_args(const struct device_node *np,
 	struct of_phandle_args *out_args);
 extern int of_count_phandle_with_args(const struct device_node *np,
 	const char *list_name, const char *cells_name);
+extern int of_count_phandle_with_fixed_args(const struct device_node *np,
+	const char *list_name, int cells_count);
 
 /* phandle iterator functions */
 extern int of_phandle_iterator_init(struct of_phandle_iterator *it,
@@ -886,6 +888,13 @@ static inline int of_count_phandle_with_args(struct device_node *np,
 	return -ENOSYS;
 }
 
+static inline int of_count_phandle_with_fixed_args(const struct device_node *np,
+						   const char *list_name,
+						   int cells_count)
+{
+	return -ENOSYS;
+}
+
 static inline int of_phandle_iterator_init(struct of_phandle_iterator *it,
 					   const struct device_node *np,
 					   const char *list_name,
-- 
2.20.1


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v2 2/7] ASoC: audio-graph-card: Add plls and sysclks DT bindings
  2020-10-16 17:35 [PATCH v2 0/7] Add support for Rpi4b + Cirrus Lochnagar2 and CS47L15 Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 1/7] of: base: Add of_count_phandle_with_fixed_args() Richard Fitzgerald
@ 2020-10-16 17:35 ` Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 3/7] ASoC: audio-graph-card: Support setting component plls and sysclks Richard Fitzgerald
                   ` (4 subsequent siblings)
  6 siblings, 0 replies; 8+ messages in thread
From: Richard Fitzgerald @ 2020-10-16 17:35 UTC (permalink / raw)
  To: broonie, robh+dt, nsaenzjulienne
  Cc: devicetree, alsa-devel, patches, linux-kernel,
	Richard Fitzgerald, linux-rpi-kernel, linux-arm-kernel

This adds the two new properties 'plls' and 'sysclks' to the dt bindings.
These add the ability to set values that will be
passed to snd_soc_component_set_sysclk() and snd_soc_component_set_pll().

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
---
 .../bindings/sound/audio-graph-card.txt       | 44 +++++++++++++++++++
 1 file changed, 44 insertions(+)

diff --git a/Documentation/devicetree/bindings/sound/audio-graph-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-card.txt
index d5f6919a2d69..59bbd5b55b59 100644
--- a/Documentation/devicetree/bindings/sound/audio-graph-card.txt
+++ b/Documentation/devicetree/bindings/sound/audio-graph-card.txt
@@ -32,6 +32,19 @@ Required properties:
 Optional properties:
 - pa-gpios: GPIO used to control external amplifier.
 
+- plls: A list of component pll settings that will be applied with
+      snd_soc_component_set_pll. Each entry is a phandle to the node of the
+      codec or cpu component, followed by the four arguments id, source,
+      frequency_in, frequency_out. Multiple entries can have the same phandle
+      so that several plls can be set in the same component.
+
+- sysclks: A list of component sysclk settings that will be applied with
+      snd_soc_component_set_sysclk. Each entry is a phandle to the node of
+      the codec or cpu component, followed by the four arguments id, source,
+      frequency, direction. Direction is 0 if the clock is an input, 1 if it
+      is an output. Multiple entries can have the same phandle so that several
+      clocks can be set in the same component.
+
 -----------------------
 Example: Single DAI case
 -----------------------
@@ -335,3 +348,34 @@ Example: Multi DAI with DPCM
 			};
 		};
 	};
+
+-----------------------
+Example: Set component sysclks and PLLs
+-----------------------
+
+	sound {
+		compatible = "audio-graph-card";
+
+		sysclks = <
+			&cs47l15 1 4 98304000 0
+			&cs47l15 8 4 147456000 0
+		>;
+		plls = <
+			&cs47l15 1 0 24576000 98304000
+		>;
+
+		dais = <&cpu_i2s_port>;
+	};
+
+	cs47l15: codec@0 {
+		...
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cs47l15_aif1_port: port@0 {
+				reg = <0>;
+				cs47l15_aif1: endpoint {
+					remote-endpoint = <&cpu_i2s_endpoint>;
+				};
+			};
+	};
-- 
2.20.1


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v2 3/7] ASoC: audio-graph-card: Support setting component plls and sysclks
  2020-10-16 17:35 [PATCH v2 0/7] Add support for Rpi4b + Cirrus Lochnagar2 and CS47L15 Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 1/7] of: base: Add of_count_phandle_with_fixed_args() Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 2/7] ASoC: audio-graph-card: Add plls and sysclks DT bindings Richard Fitzgerald
@ 2020-10-16 17:35 ` Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 4/7] ASoC: arizona: Allow codecs to be selected from kernel config Richard Fitzgerald
                   ` (3 subsequent siblings)
  6 siblings, 0 replies; 8+ messages in thread
From: Richard Fitzgerald @ 2020-10-16 17:35 UTC (permalink / raw)
  To: broonie, robh+dt, nsaenzjulienne
  Cc: devicetree, alsa-devel, patches, linux-kernel,
	Richard Fitzgerald, linux-rpi-kernel, linux-arm-kernel

Some codecs need plls and/or sysclks to be configured using the
snd_soc_component_set_[sysclk|pll] functions. These drivers cannot
necessarily be converted to use the clock framework. If the codec is on
a I2C/SPI bus, a nested clk_get would be needed to enable the bus clock.
But the clock framework does not support nested operations and this would
deadlock. So it isn't possible to implement I2C/SPI connected pll/clock
hardware through the clock framework.

This patch adds new dt properties that list phandles of components with
the pll/sysclk settings to be applied. Multiple settings can be given for
the same phandle to allow for components with multiple clocks and plls.
The plls and sysclks are enabled when the card bias level moves to STANDBY
and disabled when it moves to OFF.

The implementation does not attempt to handle specifying complex clock
ordering interdependencies between components. The plls and sysclks are
applied to a component as it is passed to the card set_bias_level/
set_bias_level_post callbacks. It follows from this that the order
components are configured is the order that they are passed to those
callbacks.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
---
 include/sound/simple_card_utils.h     |  24 ++++
 sound/soc/generic/audio-graph-card.c  |  16 ++-
 sound/soc/generic/simple-card-utils.c | 184 ++++++++++++++++++++++++++
 3 files changed, 222 insertions(+), 2 deletions(-)

diff --git a/include/sound/simple_card_utils.h b/include/sound/simple_card_utils.h
index 86a1e956991e..67e9034ed807 100644
--- a/include/sound/simple_card_utils.h
+++ b/include/sound/simple_card_utils.h
@@ -38,6 +38,15 @@ struct asoc_simple_jack {
 	struct snd_soc_jack_gpio gpio;
 };
 
+struct asoc_simple_sysclk_pll {
+	struct device_node *node;
+	int id;
+	int source;
+	unsigned int freq_in;
+	unsigned int freq_out;
+	int dir;
+};
+
 struct asoc_simple_priv {
 	struct snd_soc_card snd_card;
 	struct simple_dai_props {
@@ -56,6 +65,11 @@ struct asoc_simple_priv {
 	struct asoc_simple_dai *dais;
 	struct snd_soc_codec_conf *codec_conf;
 	struct gpio_desc *pa_gpio;
+
+	struct asoc_simple_sysclk_pll *sysclks;
+	int num_sysclks;
+	struct asoc_simple_sysclk_pll *plls;
+	int num_plls;
 };
 #define simple_priv_to_card(priv)	(&(priv)->snd_card)
 #define simple_priv_to_props(priv, i)	((priv)->dai_props + (i))
@@ -94,6 +108,14 @@ void asoc_simple_shutdown(struct snd_pcm_substream *substream);
 int asoc_simple_hw_params(struct snd_pcm_substream *substream,
 			  struct snd_pcm_hw_params *params);
 int asoc_simple_dai_init(struct snd_soc_pcm_runtime *rtd);
+
+int asoc_simple_set_bias_level(struct snd_soc_card *card,
+			       struct snd_soc_dapm_context *dapm,
+			       enum snd_soc_bias_level level);
+int asoc_simple_set_bias_level_post(struct snd_soc_card *card,
+				    struct snd_soc_dapm_context *dapm,
+				    enum snd_soc_bias_level level);
+
 int asoc_simple_be_hw_params_fixup(struct snd_soc_pcm_runtime *rtd,
 				   struct snd_pcm_hw_params *params);
 
@@ -128,6 +150,8 @@ int asoc_simple_parse_widgets(struct snd_soc_card *card,
 				      char *prefix);
 int asoc_simple_parse_pin_switches(struct snd_soc_card *card,
 				   char *prefix);
+int asoc_simple_parse_sysclks(struct asoc_simple_priv *priv, char *prefix);
+int asoc_simple_parse_plls(struct asoc_simple_priv *priv, char *prefix);
 
 int asoc_simple_init_jack(struct snd_soc_card *card,
 			       struct asoc_simple_jack *sjack,
diff --git a/sound/soc/generic/audio-graph-card.c b/sound/soc/generic/audio-graph-card.c
index 97b4f5480a31..c56a3a19a22f 100644
--- a/sound/soc/generic/audio-graph-card.c
+++ b/sound/soc/generic/audio-graph-card.c
@@ -509,6 +509,14 @@ static int graph_parse_of(struct asoc_simple_priv *priv)
 			return ret;
 	}
 
+	ret = asoc_simple_parse_sysclks(priv, NULL);
+	if (ret < 0)
+		return ret;
+
+	ret = asoc_simple_parse_plls(priv, NULL);
+	if (ret < 0)
+		return ret;
+
 	return asoc_simple_parse_card_name(card, NULL);
 }
 
@@ -642,6 +650,7 @@ static int graph_probe(struct platform_device *pdev)
 	card->dapm_widgets	= graph_dapm_widgets;
 	card->num_dapm_widgets	= ARRAY_SIZE(graph_dapm_widgets);
 	card->probe		= graph_card_probe;
+	snd_soc_card_set_drvdata(card, priv);
 
 	memset(&li, 0, sizeof(li));
 	graph_get_dais_count(priv, &li);
@@ -666,10 +675,13 @@ static int graph_probe(struct platform_device *pdev)
 		goto err;
 	}
 
-	snd_soc_card_set_drvdata(card, priv);
-
 	asoc_simple_debug_info(priv);
 
+	if (priv->num_sysclks || priv->num_plls) {
+		card->set_bias_level = asoc_simple_set_bias_level;
+		card->set_bias_level_post = asoc_simple_set_bias_level_post;
+	}
+
 	ret = devm_snd_soc_register_card(dev, card);
 	if (ret < 0)
 		goto err;
diff --git a/sound/soc/generic/simple-card-utils.c b/sound/soc/generic/simple-card-utils.c
index 6cada4c1e283..6c0675187285 100644
--- a/sound/soc/generic/simple-card-utils.c
+++ b/sound/soc/generic/simple-card-utils.c
@@ -399,6 +399,123 @@ int asoc_simple_dai_init(struct snd_soc_pcm_runtime *rtd)
 }
 EXPORT_SYMBOL_GPL(asoc_simple_dai_init);
 
+static bool asoc_simple_node_is_component(struct snd_soc_component *component,
+					  struct device_node *node)
+{
+	struct device_node *comp_node;
+
+	comp_node = component->dev->of_node;
+	if (!comp_node && component->dev->parent)
+		comp_node = component->dev->parent->of_node;
+
+	return (comp_node == node);
+}
+
+int asoc_simple_set_bias_level(struct snd_soc_card *card,
+			       struct snd_soc_dapm_context *dapm,
+			       enum snd_soc_bias_level level)
+{
+	struct asoc_simple_priv *priv = snd_soc_card_get_drvdata(card);
+	struct snd_soc_component *component = dapm->component;
+	int i, ret;
+
+	if (!component)
+		return 0;
+
+	switch (level) {
+	case SND_SOC_BIAS_STANDBY:
+		if (dapm->bias_level != SND_SOC_BIAS_OFF)
+			break;
+
+		/* PLLs normally supply SYSCLKs so enable the PLLs first. */
+		for (i = 0; i < priv->num_plls; ++i) {
+			if (!asoc_simple_node_is_component(component, priv->plls[i].node))
+				continue;
+
+			ret = snd_soc_component_set_pll(component,
+							priv->plls[i].id,
+							priv->plls[i].source,
+							priv->plls[i].freq_in,
+							priv->plls[i].freq_out);
+			if (ret) {
+				dev_err(card->dev, "Failed to set pll for %s: %d\n",
+					component->name, ret);
+				return ret;
+			}
+		}
+
+		for (i = 0; i < priv->num_sysclks; ++i) {
+			if (!asoc_simple_node_is_component(component, priv->sysclks[i].node))
+				continue;
+
+			ret = snd_soc_component_set_sysclk(component,
+							   priv->sysclks[i].id,
+							   priv->sysclks[i].source,
+							   priv->sysclks[i].freq_in,
+							   priv->sysclks[i].dir);
+			if (ret) {
+				dev_err(card->dev, "Failed to set sysclk for %s: %d\n",
+					component->name, ret);
+				return ret;
+			}
+		}
+		break;
+	default:
+		break;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(asoc_simple_set_bias_level);
+
+int asoc_simple_set_bias_level_post(struct snd_soc_card *card,
+				    struct snd_soc_dapm_context *dapm,
+				    enum snd_soc_bias_level level)
+{
+	struct asoc_simple_priv *priv = snd_soc_card_get_drvdata(card);
+	struct snd_soc_component *component = dapm->component;
+	int i, ret;
+
+	if (!component)
+		goto out;
+
+	switch (level) {
+	case SND_SOC_BIAS_OFF:
+		for (i = 0; i < priv->num_sysclks; ++i) {
+			if (!asoc_simple_node_is_component(component, priv->sysclks[i].node))
+				continue;
+
+			ret = snd_soc_component_set_sysclk(component,
+							   priv->sysclks[i].id,
+							   0,
+							   0,
+							   priv->sysclks[i].dir);
+			if (ret)
+				dev_warn(card->dev, "Failed to set sysclk for %s: %d\n",
+					 component->name, ret);
+		}
+
+		for (i = 0; i < priv->num_plls; ++i) {
+			if (!asoc_simple_node_is_component(component, priv->plls[i].node))
+				continue;
+
+			ret = snd_soc_component_set_pll(component, priv->plls[i].id, 0, 0, 0);
+			if (ret)
+				dev_warn(card->dev, "Failed to set pll for %s: %d\n",
+					 component->name, ret);
+		}
+		break;
+	default:
+		break;
+	}
+
+out:
+	dapm->bias_level = level;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(asoc_simple_set_bias_level_post);
+
 void asoc_simple_canonicalize_platform(struct snd_soc_dai_link *dai_link)
 {
 	/* Assumes platform == cpu */
@@ -433,6 +550,7 @@ EXPORT_SYMBOL_GPL(asoc_simple_canonicalize_cpu);
 
 int asoc_simple_clean_reference(struct snd_soc_card *card)
 {
+	struct asoc_simple_priv *priv = snd_soc_card_get_drvdata(card);
 	struct snd_soc_dai_link *dai_link;
 	int i;
 
@@ -440,6 +558,13 @@ int asoc_simple_clean_reference(struct snd_soc_card *card)
 		of_node_put(dai_link->cpus->of_node);
 		of_node_put(dai_link->codecs->of_node);
 	}
+
+	for (i = 0; i < priv->num_sysclks; ++i)
+		of_node_put(priv->sysclks[i].node);
+
+	for (i = 0; i < priv->num_plls; ++i)
+		of_node_put(priv->plls[i].node);
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(asoc_simple_clean_reference);
@@ -538,6 +663,65 @@ int asoc_simple_parse_pin_switches(struct snd_soc_card *card,
 }
 EXPORT_SYMBOL_GPL(asoc_simple_parse_pin_switches);
 
+static int asoc_simple_parse_sysclks_plls(struct asoc_simple_priv *priv,
+					  char *prefix,
+					  char *prop_root_name,
+					  struct asoc_simple_sysclk_pll **out,
+					  int *out_count)
+{
+	struct device *dev = priv->snd_card.dev;
+	struct device_node *node = dev->of_node;
+	struct of_phandle_args args;
+	int n_elem, i, ret;
+	char prop[128];
+
+	if (!prefix)
+		prefix = "";
+
+	snprintf(prop, sizeof(prop), "%s%s", prefix, prop_root_name);
+	n_elem = of_count_phandle_with_fixed_args(node, prop, 4);
+	if (n_elem == -ENOENT || n_elem == 0) {
+		return 0;
+	} else if (n_elem < 0) {
+		dev_err(dev, "Failed to parse %s: %d\n", prop, n_elem);
+		return n_elem;
+	}
+
+	*out = devm_kcalloc(dev, n_elem, sizeof(**out), GFP_KERNEL);
+	if (!*out)
+		return -ENOMEM;
+	*out_count = n_elem;
+
+	for (i = 0; i < n_elem; ++i) {
+		ret = of_parse_phandle_with_fixed_args(node, prop, 4, i, &args);
+		if (ret < 0)
+			return ret;
+
+		(*out)[i].node		= args.np;
+		(*out)[i].id		= args.args[0];
+		(*out)[i].source	= args.args[1];
+		(*out)[i].freq_in	= args.args[2];
+		(*out)[i].dir		= args.args[3]; /* for sysclks */
+		(*out)[i].freq_out	= args.args[3]; /* for plls */
+	}
+
+	return 0;
+}
+
+int asoc_simple_parse_sysclks(struct asoc_simple_priv *priv, char *prefix)
+{
+	return asoc_simple_parse_sysclks_plls(priv, prefix, "sysclks",
+					      &priv->sysclks, &priv->num_sysclks);
+}
+EXPORT_SYMBOL_GPL(asoc_simple_parse_sysclks);
+
+int asoc_simple_parse_plls(struct asoc_simple_priv *priv, char *prefix)
+{
+	return asoc_simple_parse_sysclks_plls(priv, prefix, "plls",
+					      &priv->plls, &priv->num_plls);
+}
+EXPORT_SYMBOL_GPL(asoc_simple_parse_plls);
+
 int asoc_simple_init_jack(struct snd_soc_card *card,
 			  struct asoc_simple_jack *sjack,
 			  int is_hp, char *prefix,
-- 
2.20.1


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v2 4/7] ASoC: arizona: Allow codecs to be selected from kernel config
  2020-10-16 17:35 [PATCH v2 0/7] Add support for Rpi4b + Cirrus Lochnagar2 and CS47L15 Richard Fitzgerald
                   ` (2 preceding siblings ...)
  2020-10-16 17:35 ` [PATCH v2 3/7] ASoC: audio-graph-card: Support setting component plls and sysclks Richard Fitzgerald
@ 2020-10-16 17:35 ` Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 5/7] ASoC: madera: " Richard Fitzgerald
                   ` (2 subsequent siblings)
  6 siblings, 0 replies; 8+ messages in thread
From: Richard Fitzgerald @ 2020-10-16 17:35 UTC (permalink / raw)
  To: broonie, robh+dt, nsaenzjulienne
  Cc: devicetree, alsa-devel, patches, linux-kernel,
	Richard Fitzgerald, linux-rpi-kernel, linux-arm-kernel

The codec Kconfig options were hidden and intended to be selected by
the machine driver that requires them. But that means having either a
dedicated machine driver or building all codecs.

This patch makes the Kconfig options visible so that they can be
selected independently of the machine driver, allowing the codec to be
used with simple-card and other machine drivers that are not hardcoded
to use a fixed set of codecs.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
---
 sound/soc/codecs/Kconfig | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index 34c6dd04b85a..4a8d503bdd38 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -661,7 +661,7 @@ config SND_SOC_CS47L15
 	tristate
 
 config SND_SOC_CS47L24
-	tristate
+	tristate "Cirrus Logic CS47L24 CODEC"
 	depends on MFD_CS47L24
 
 config SND_SOC_CS47L35
@@ -1484,11 +1484,11 @@ config SND_SOC_WM5100
 	depends on I2C
 
 config SND_SOC_WM5102
-	tristate
+	tristate "Cirrus Logic WM5102 CODEC"
 	depends on MFD_WM5102
 
 config SND_SOC_WM5110
-	tristate
+	tristate "Cirrus Logic WM5110 CODEC"
 	depends on MFD_WM5110
 
 config SND_SOC_WM8350
@@ -1657,7 +1657,7 @@ config SND_SOC_WM8997
 	depends on MFD_WM8997
 
 config SND_SOC_WM8998
-	tristate
+	tristate "Cirrus Logic WM8998 CODEC"
 	depends on MFD_WM8998
 
 config SND_SOC_WM9081
-- 
2.20.1


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v2 5/7] ASoC: madera: Allow codecs to be selected from kernel config
  2020-10-16 17:35 [PATCH v2 0/7] Add support for Rpi4b + Cirrus Lochnagar2 and CS47L15 Richard Fitzgerald
                   ` (3 preceding siblings ...)
  2020-10-16 17:35 ` [PATCH v2 4/7] ASoC: arizona: Allow codecs to be selected from kernel config Richard Fitzgerald
@ 2020-10-16 17:35 ` Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 6/7] ARM: dts: Add dts for RPi4b + Cirrus Logic Lochnagar2 + CS47L15 Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 7/7] MAINTAINERS: Add dts for Cirrus Logic Lochnagar on RPi4 Richard Fitzgerald
  6 siblings, 0 replies; 8+ messages in thread
From: Richard Fitzgerald @ 2020-10-16 17:35 UTC (permalink / raw)
  To: broonie, robh+dt, nsaenzjulienne
  Cc: devicetree, alsa-devel, patches, linux-kernel,
	Richard Fitzgerald, linux-rpi-kernel, linux-arm-kernel

The codec Kconfig options were hidden and intended to be selected by
the machine driver that requires them. But that means having either a
dedicated machine driver or building all codecs.

This patch makes the Kconfig options visible so that they can be
selected independently of the machine driver, allowing the codec to be
used with simple-card and other machine drivers that are not hardcoded
to use a fixed set of codecs.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
---
 sound/soc/codecs/Kconfig | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index 4a8d503bdd38..e0aed608dbc3 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -658,23 +658,23 @@ config SND_SOC_CS4349
 	depends on I2C
 
 config SND_SOC_CS47L15
-	tristate
+	tristate "Cirrus Logic CS47L15 CODEC"
 
 config SND_SOC_CS47L24
 	tristate "Cirrus Logic CS47L24 CODEC"
 	depends on MFD_CS47L24
 
 config SND_SOC_CS47L35
-	tristate
+	tristate "Cirrus Logic CS47L35 CODEC"
 
 config SND_SOC_CS47L85
-	tristate
+	tristate "Cirrus Logic CS47L85 CODEC"
 
 config SND_SOC_CS47L90
-	tristate
+	tristate "Cirrus Logic CS47L90 CODEC"
 
 config SND_SOC_CS47L92
-	tristate
+	tristate "Cirrus Logic CS47L92 CODEC"
 
 # Cirrus Logic Quad-Channel ADC
 config SND_SOC_CS53L30
-- 
2.20.1


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v2 6/7] ARM: dts: Add dts for RPi4b + Cirrus Logic Lochnagar2 + CS47L15
  2020-10-16 17:35 [PATCH v2 0/7] Add support for Rpi4b + Cirrus Lochnagar2 and CS47L15 Richard Fitzgerald
                   ` (4 preceding siblings ...)
  2020-10-16 17:35 ` [PATCH v2 5/7] ASoC: madera: " Richard Fitzgerald
@ 2020-10-16 17:35 ` Richard Fitzgerald
  2020-10-16 17:35 ` [PATCH v2 7/7] MAINTAINERS: Add dts for Cirrus Logic Lochnagar on RPi4 Richard Fitzgerald
  6 siblings, 0 replies; 8+ messages in thread
From: Richard Fitzgerald @ 2020-10-16 17:35 UTC (permalink / raw)
  To: broonie, robh+dt, nsaenzjulienne
  Cc: devicetree, alsa-devel, patches, linux-kernel,
	Richard Fitzgerald, linux-rpi-kernel, linux-arm-kernel

This adds a devicetree configuration for Raspberry Pi 4b connected to
Cirrus Logic Lochnagar 2 audio development board and CS47L15 codec.

The common (codec-independent) Lochnagar 2 configuration is separated
into a dtsi to simplify re-using it for other codecs.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
---
 arch/arm/boot/dts/Makefile                    |   1 +
 ...bcm2711-rpi4b-cirrus-lochnagar-cs47l15.dts | 166 +++++++++++++++
 .../dts/bcm2711-rpi4b-cirrus-lochnagar.dtsi   | 201 ++++++++++++++++++
 3 files changed, 368 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar-cs47l15.dts
 create mode 100644 arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4572db3fa5ae..7c4f1e2a7005 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -92,6 +92,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2837-rpi-3-b-plus.dtb \
 	bcm2837-rpi-cm3-io3.dtb \
 	bcm2711-rpi-4-b.dtb \
+	bcm2711-rpi4b-cirrus-lochnagar-cs47l15.dtb \
 	bcm2835-rpi-zero.dtb \
 	bcm2835-rpi-zero-w.dtb
 dtb-$(CONFIG_ARCH_BCM_5301X) += \
diff --git a/arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar-cs47l15.dts b/arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar-cs47l15.dts
new file mode 100644
index 000000000000..f23d0ace5467
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar-cs47l15.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711-rpi4b-cirrus-lochnagar.dtsi"
+#include <dt-bindings/sound/madera.h>
+
+/ {
+	sound {
+		status = "okay";
+
+		compatible = "audio-graph-card";
+		label = "sound-card-cs47l15";
+
+		sysclks = <
+			&cs47l15 1 4 98304000 0
+			&cs47l15 8 4 147456000 0
+		>;
+		plls = <
+			&cs47l15 1 0 24576000 98304000
+		>;
+
+		widgets = "Microphone", "Microphone Jack",
+			  "Headphone", "Headphone Jack";
+
+		routing = "Microphone Jack", "MICBIAS1A",
+			  "IN1BRN", "Microphone Jack",
+			  "IN1BRP", "Microphone Jack",
+			  "Headphone Jack", "HPOUTL",
+			  "Headphone Jack", "HPOUTR";
+
+		dais = <&cpu_i2s_port &cs47l15_trace_port>;
+	};
+};
+
+&i2s {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu_i2s_port: port@0 {
+			reg = <0>;
+			cpu_i2s_ep: endpoint {
+				remote-endpoint = <&cs47l15_aif1>;
+				dai-format = "i2s";
+			};
+		};
+	};
+};
+
+&spi {
+	status = "okay";
+
+	cs47l15: cs47l15@1 {
+		status = "okay";
+
+		compatible = "cirrus,cs47l15";
+		reg = <0x1>;
+
+		spi-max-frequency = <11000000>;
+
+		interrupts = <27 8>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#sound-dai-cells = <1>;
+
+		AVDD-supply = <&lochnagar_vdd1v8>;
+		DCVDD-supply = <&lochnagar_vddcore>;
+		DBVDD1-supply = <&lochnagar_vdd1v8>;
+		CPVDD1-supply = <&lochnagar_vdd1v8>;
+		SPKVDD-supply = <&wallvdd>;
+		MICVDD-supply = <&lochnagar_micvdd>;
+
+		reset-gpios = <&lochnagar_pin 0 0>;
+
+		cirrus,dmic-ref = <
+			MADERA_DMIC_REF_MICBIAS1
+		>;
+		cirrus,inmode = <
+			MADERA_INMODE_SE   MADERA_INMODE_SE   /* IN1A */
+			MADERA_INMODE_DIFF MADERA_INMODE_DIFF /* IN1B */
+			MADERA_INMODE_SE   MADERA_INMODE_SE   /* IN2A */
+			MADERA_INMODE_DIFF MADERA_INMODE_DIFF /* IN2B */
+		>;
+
+		clocks = <&lochnagar_clk LOCHNAGAR_CDC_MCLK1>,
+			 <&lochnagar_clk LOCHNAGAR_CDC_MCLK2>;
+		clock-names = "mclk1", "mclk2";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&cdc_irq &cs47l15_defaults>;
+
+		cs47l15_defaults: cs47l15-gpio-defaults {
+			aif1 {
+				groups = "aif1";
+				function = "aif1";
+				bias-bus-hold;
+			};
+			aif2 {
+				groups = "aif2";
+				function = "aif2";
+				bias-bus-hold;
+			};
+			aif3 {
+				groups = "aif3";
+				function = "aif3";
+				bias-bus-hold;
+			};
+			pdmspk1 {
+				groups = "pdmspk1";
+				function = "pdmspk1";
+			};
+		};
+
+		micvdd {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		MICBIAS1 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		MICBIAS1A {
+			regulator-active-discharge = <1>;
+		};
+		MICBIAS1B {
+			regulator-active-discharge = <1>;
+		};
+		MICBIAS1C {
+			regulator-active-discharge = <1>;
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cs47l15_aif1_port: port@0 {
+				reg = <0>;
+				cs47l15_aif1: endpoint {
+					remote-endpoint = <&cpu_i2s_ep>;
+					bitclock-master;
+					frame-master;
+					system-clock-frequency = <0>;
+					mclk-fs = <0>;
+				};
+			};
+			/* Debug trace compressed stream */
+			cs47l15_trace_port: port@3 {
+				reg = <3>;
+				cs47l15_trace_cpu: endpoint {
+					remote-endpoint = <&cs47l15_trace_codec>;
+					system-clock-frequency = <0>;
+					mclk-fs = <0>;
+				};
+			};
+			port@4 {
+				reg = <4>;
+				cs47l15_trace_codec: endpoint {
+					remote-endpoint = <&cs47l15_trace_cpu>;
+					system-clock-frequency = <0>;
+					mclk-fs = <0>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar.dtsi b/arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar.dtsi
new file mode 100644
index 000000000000..af498d7ad18a
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar.dtsi
@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711-rpi-4-b.dts"
+#include <dt-bindings/clk/lochnagar.h>
+#include <dt-bindings/pinctrl/bcm2835.h>
+#include <dt-bindings/pinctrl/lochnagar.h>
+
+/ {
+	wallvdd: wallvdd@0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "WALL_VDD_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+};
+
+&gpio {
+	lochnagar_present: lochnagar_present {
+		brcm,pins = <22>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	lochnagar_reset: lochnagar_reset {
+		brcm,pins = <24>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	cdc_irq: cdc_irq {
+		brcm,pins = <27>;
+		brcm,function = <BCM2835_FSEL_GPIO_IN>;
+	};
+
+	spi_pins: spi_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+
+	spi_cs: spi_cs {
+		brcm,pins = <7 8>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	i2s_pins: i2s_pins {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&i2s {
+	status = "okay";
+	#sound-dai-cells = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+	dmas = <&dma 2>, <&dma 3>;
+	dma-names = "tx", "rx";
+};
+
+&i2c1 {
+	status = "okay";
+
+	lochnagar: lochnagar@22 {
+		status = "okay";
+
+		compatible = "cirrus,lochnagar2";
+		reg = <0x22>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lochnagar_present &lochnagar_reset>;
+
+		reset-gpio = <&gpio 24 0>;
+		present-gpio = <&gpio 22 0>;
+
+		lochnagar_vdd1v8: VDD1V8 {
+			compatible = "regulator-fixed";
+
+			regulator-name = "VDD1V8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+			regulator-always-on;
+
+			vin-supply = <&wallvdd>;
+		};
+
+		clk_pmic: clk_pmic {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+		clk_24m: clk_24m {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24576000>;
+		};
+
+		lochnagar_clk: clk {
+			compatible = "cirrus,lochnagar2-clk";
+
+			#clock-cells = <1>;
+
+			clocks = <&clk_pmic>, <&clk_24m>;
+			clock-names = "ln-pmic-32k", "ln-clk-24m";
+
+			assigned-clocks = <&lochnagar_clk LOCHNAGAR_CDC_MCLK1>,
+					  <&lochnagar_clk LOCHNAGAR_CDC_MCLK2>,
+					  <&lochnagar_clk LOCHNAGAR_SOUNDCARD_MCLK>;
+			assigned-clock-parents = <&clk_24m>,
+						 <&clk_pmic>,
+						 <&clk_24m>;
+		};
+
+		lochnagar_pin: pin {
+			compatible = "cirrus,lochnagar-pinctrl";
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&lochnagar_pin 0 0 LOCHNAGAR2_PIN_NUM_GPIOS>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pin_settings>;
+
+			pin_settings: pin_settings {
+				rpi_aif {
+					input-enable;
+					groups = "gf-aif1";
+					function = "codec-aif1";
+				};
+				codec_aif1 {
+					output-master;
+					groups = "codec-aif1";
+					function = "gf-aif1";
+				};
+				sc_codec_aif {
+					output-enable;
+					groups = "codec-aif2";
+					function = "soundcard-aif";
+				};
+				sc_lochnagar_aif {
+					input-enable;
+					groups = "soundcard-aif";
+					function = "codec-aif2";
+				};
+			};
+		};
+
+		lochnagar_hwmon: hwmon {
+			compatible = "cirrus,lochnagar2-hwmon";
+		};
+
+		lochnagar_micvdd: MICVDD {
+			compatible = "cirrus,lochnagar2-micvdd";
+
+			SYSVDD-supply = <&wallvdd>;
+
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		MIC1VDD {
+			compatible = "cirrus,lochnagar2-mic1vdd";
+
+			regulator-always-on;
+			cirrus,micbias-input = <2>;
+		};
+
+		MIC2VDD {
+			compatible = "cirrus,lochnagar2-mic2vdd";
+
+			regulator-always-on;
+			cirrus,micbias-input = <3>;
+		};
+
+		lochnagar_vddcore: VDDCORE {
+			compatible = "cirrus,lochnagar2-vddcore";
+
+			SYSVDD-supply = <&wallvdd>;
+
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		lochnagar_sc: soundcard {
+			compatible = "cirrus,lochnagar2-soundcard";
+
+			#sound-dai-cells = <1>;
+
+			clocks = <&lochnagar_clk LOCHNAGAR_SOUNDCARD_MCLK>;
+			clock-names = "mclk";
+		};
+	};
+};
+
+&spi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_pins &spi_cs>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+};
-- 
2.20.1


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v2 7/7] MAINTAINERS: Add dts for Cirrus Logic Lochnagar on RPi4
  2020-10-16 17:35 [PATCH v2 0/7] Add support for Rpi4b + Cirrus Lochnagar2 and CS47L15 Richard Fitzgerald
                   ` (5 preceding siblings ...)
  2020-10-16 17:35 ` [PATCH v2 6/7] ARM: dts: Add dts for RPi4b + Cirrus Logic Lochnagar2 + CS47L15 Richard Fitzgerald
@ 2020-10-16 17:35 ` Richard Fitzgerald
  6 siblings, 0 replies; 8+ messages in thread
From: Richard Fitzgerald @ 2020-10-16 17:35 UTC (permalink / raw)
  To: broonie, robh+dt, nsaenzjulienne
  Cc: devicetree, alsa-devel, patches, linux-kernel,
	Richard Fitzgerald, linux-rpi-kernel, linux-arm-kernel

Update the Cirrus Logic driver maintainers to include the device
tree files for using the Lochnagar with a Raspberry Pi 4.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 0f59b0412953..d0065cba9535 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4193,6 +4193,7 @@ M:	Charles Keepax <ckeepax@opensource.cirrus.com>
 M:	Richard Fitzgerald <rf@opensource.cirrus.com>
 L:	patches@opensource.cirrus.com
 S:	Supported
+F:	arch/arm/boot/dts/bcm2711-rpi4b-cirrus-lochnagar*
 F:	Documentation/devicetree/bindings/clock/cirrus,lochnagar.yaml
 F:	Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.yaml
 F:	Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml
-- 
2.20.1


^ permalink raw reply	[flat|nested] 8+ messages in thread

end of thread, back to index

Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-10-16 17:35 [PATCH v2 0/7] Add support for Rpi4b + Cirrus Lochnagar2 and CS47L15 Richard Fitzgerald
2020-10-16 17:35 ` [PATCH v2 1/7] of: base: Add of_count_phandle_with_fixed_args() Richard Fitzgerald
2020-10-16 17:35 ` [PATCH v2 2/7] ASoC: audio-graph-card: Add plls and sysclks DT bindings Richard Fitzgerald
2020-10-16 17:35 ` [PATCH v2 3/7] ASoC: audio-graph-card: Support setting component plls and sysclks Richard Fitzgerald
2020-10-16 17:35 ` [PATCH v2 4/7] ASoC: arizona: Allow codecs to be selected from kernel config Richard Fitzgerald
2020-10-16 17:35 ` [PATCH v2 5/7] ASoC: madera: " Richard Fitzgerald
2020-10-16 17:35 ` [PATCH v2 6/7] ARM: dts: Add dts for RPi4b + Cirrus Logic Lochnagar2 + CS47L15 Richard Fitzgerald
2020-10-16 17:35 ` [PATCH v2 7/7] MAINTAINERS: Add dts for Cirrus Logic Lochnagar on RPi4 Richard Fitzgerald

Alsa-Devel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/alsa-devel/0 alsa-devel/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 alsa-devel alsa-devel/ https://lore.kernel.org/alsa-devel \
		alsa-devel@alsa-project.org
	public-inbox-index alsa-devel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.alsa-project.alsa-devel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git