* [PATCH v2] ASoC: dt-bindings: fsl,sai: Convert format to json-schema
@ 2022-07-28 15:04 Shengjiu Wang
2022-07-28 16:42 ` Krzysztof Kozlowski
0 siblings, 1 reply; 3+ messages in thread
From: Shengjiu Wang @ 2022-07-28 15:04 UTC (permalink / raw)
To: lgirdwood, broonie, robh+dt, krzysztof.kozlowski+dt, alsa-devel,
devicetree, linux-kernel
Cc: shengjiu.wang
Convert the NXP SAI binding to DT schema format using json-schema.
The Synchronous Audio Interface (SAI) provides an interface that
supports full-duplex serial interfaces with frame synchronization
formats such as I2S, AC97, TDM, and codec/DSP interfaces.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
---
changes in v2
- fix exclusive property issue
- fix order issue of compatible, clock-names, dma-names
.../devicetree/bindings/sound/fsl,sai.yaml | 215 ++++++++++++++++++
.../devicetree/bindings/sound/fsl-sai.txt | 95 --------
2 files changed, 215 insertions(+), 95 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/fsl,sai.yaml
delete mode 100644 Documentation/devicetree/bindings/sound/fsl-sai.txt
diff --git a/Documentation/devicetree/bindings/sound/fsl,sai.yaml b/Documentation/devicetree/bindings/sound/fsl,sai.yaml
new file mode 100644
index 000000000000..3e3d99febd69
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/fsl,sai.yaml
@@ -0,0 +1,215 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/fsl,sai.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale Synchronous Audio Interface (SAI).
+
+maintainers:
+ - Shengjiu Wang <shengjiu.wang@nxp.com>
+
+description: |
+ The SAI is based on I2S module that used communicating with audio codecs,
+ which provides a synchronous audio interface that supports fullduplex
+ serial interfaces with frame synchronization such as I2S, AC97, TDM, and
+ codec/DSP interfaces.
+
+properties:
+ compatible:
+ oneOf:
+ - const: fsl,vf610-sai
+ - const: fsl,imx6sx-sai
+ - const: fsl,imx6ul-sai
+ - const: fsl,imx7ulp-sai
+ - const: fsl,imx8mq-sai
+ - const: fsl,imx8qm-sai
+ - const: fsl,imx8ulp-sai
+ - items:
+ - enum:
+ - fsl,imx8mm-sai
+ - fsl,imx8mn-sai
+ - fsl,imx8mp-sai
+ - const: fsl,imx8mq-sai
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ items:
+ - description: receive and transmit interrupt
+
+ dmas:
+ maxItems: 2
+
+ dma-names:
+ maxItems: 2
+
+ clocks:
+ items:
+ - description: The ipg clock for register access
+ - description: master clock source 0 (obsoleted)
+ - description: master clock source 1
+ - description: master clock source 2
+ - description: master clock source 3
+ - description: PLL clock source for 8kHz series
+ - description: PLL clock source for 11kHz series
+ minItems: 4
+
+ clock-names:
+ oneOf:
+ - items:
+ - const: bus
+ - const: mclk0
+ - const: mclk1
+ - const: mclk2
+ - const: mclk3
+ - const: pll8k
+ - const: pll11k
+ minItems: 4
+ - items:
+ - const: bus
+ - const: mclk1
+ - const: mclk2
+ - const: mclk3
+ - const: pll8k
+ - const: pll11k
+ minItems: 4
+
+ lsb-first:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ Configures whether the LSB or the MSB is transmitted
+ first for the fifo data. If this property is absent,
+ the MSB is transmitted first as default, or the LSB
+ is transmitted first.
+
+ big-endian:
+ description: |
+ required if all the SAI registers are big-endian rather than little-endian.
+ type: boolean
+
+ fsl,sai-synchronous-rx:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ SAI will work in the synchronous mode (sync Tx with Rx) which means
+ both the transmitter and the receiver will send and receive data by
+ following receiver's bit clocks and frame sync clocks.
+
+ fsl,sai-asynchronous:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ SAI will work in the asynchronous mode, which means both transmitter
+ and receiver will send and receive data by following their own bit clocks
+ and frame sync clocks separately.
+ If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the
+ default synchronous mode (sync Rx with Tx) will be used, which means both
+ transmitter and receiver will send and receive data by following clocks
+ of transmitter.
+
+ fsl,dataline:
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ description: |
+ Configure the dataline. It has 3 value for each configuration
+ items:
+ items:
+ - description: format Default(0), I2S(1) or PDM(2)
+ enum: [0, 1, 2]
+ - description: dataline mask for 'rx'
+ - description: dataline mask for 'tx'
+
+ fsl,sai-mclk-direction-output:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ SAI will output the SAI MCLK clock.
+
+ fsl,shared-interrupt:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ Interrupt is shared with other modules.
+
+ "#sound-dai-cells":
+ const: 0
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: fsl,vf610-sai
+ then:
+ properties:
+ dmas:
+ items:
+ - description: DMA controller phandle and request line for TX
+ - description: DMA controller phandle and request line for RX
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+ else:
+ properties:
+ dmas:
+ items:
+ - description: DMA controller phandle and request line for RX
+ - description: DMA controller phandle and request line for TX
+ dma-names:
+ items:
+ - const: rx
+ - const: tx
+ - if:
+ required:
+ - fsl,sai-asynchronous
+ then:
+ properties:
+ fsl,sai-synchronous-rx: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - dmas
+ - dma-names
+ - clocks
+ - clock-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/vf610-clock.h>
+ sai2: sai@40031000 {
+ compatible = "fsl,vf610-sai";
+ reg = <0x40031000 0x1000>;
+ interrupts = <86 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai2_1>;
+ clocks = <&clks VF610_CLK_PLATFORM_BUS>,
+ <&clks VF610_CLK_SAI2>,
+ <&clks 0>, <&clks 0>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx", "rx";
+ dmas = <&edma0 0 21>,
+ <&edma0 0 20>;
+ big-endian;
+ lsb-first;
+ };
+
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/imx8mm-clock.h>
+ sai1: sai@30010000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ reg = <0x30010000 0x10000>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SAI1_IPG>,
+ <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_SAI1_ROOT>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma2 0 2 0>, <&sdma2 1 2 0>;
+ dma-names = "rx", "tx";
+ fsl,dataline = <1 0xff 0xff 2 0xff 0x11>;
+ };
diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt
deleted file mode 100644
index fbdefc3fade7..000000000000
--- a/Documentation/devicetree/bindings/sound/fsl-sai.txt
+++ /dev/null
@@ -1,95 +0,0 @@
-Freescale Synchronous Audio Interface (SAI).
-
-The SAI is based on I2S module that used communicating with audio codecs,
-which provides a synchronous audio interface that supports fullduplex
-serial interfaces with frame synchronization such as I2S, AC97, TDM, and
-codec/DSP interfaces.
-
-Required properties:
-
- - compatible : Compatible list, contains "fsl,vf610-sai",
- "fsl,imx6sx-sai", "fsl,imx6ul-sai",
- "fsl,imx7ulp-sai", "fsl,imx8mq-sai",
- "fsl,imx8qm-sai", "fsl,imx8mm-sai",
- "fsl,imx8mn-sai", "fsl,imx8mp-sai", or
- "fsl,imx8ulp-sai".
-
- - reg : Offset and length of the register set for the device.
-
- - clocks : Must contain an entry for each entry in clock-names.
-
- - clock-names : Must include the "bus" for register access and
- "mclk1", "mclk2", "mclk3" for bit clock and frame
- clock providing.
- "pll8k", "pll11k" are optional, they are the clock
- source for root clock, one is for 8kHz series rates
- another one is for 11kHz series rates.
- - dmas : Generic dma devicetree binding as described in
- Documentation/devicetree/bindings/dma/dma.txt.
-
- - dma-names : Two dmas have to be defined, "tx" and "rx".
-
- - pinctrl-names : Must contain a "default" entry.
-
- - pinctrl-NNN : One property must exist for each entry in
- pinctrl-names. See ../pinctrl/pinctrl-bindings.txt
- for details of the property values.
-
- - lsb-first : Configures whether the LSB or the MSB is transmitted
- first for the fifo data. If this property is absent,
- the MSB is transmitted first as default, or the LSB
- is transmitted first.
-
- - fsl,sai-synchronous-rx: This is a boolean property. If present, indicating
- that SAI will work in the synchronous mode (sync Tx
- with Rx) which means both the transmitter and the
- receiver will send and receive data by following
- receiver's bit clocks and frame sync clocks.
-
- - fsl,sai-asynchronous: This is a boolean property. If present, indicating
- that SAI will work in the asynchronous mode, which
- means both transmitter and receiver will send and
- receive data by following their own bit clocks and
- frame sync clocks separately.
-
- - fsl,dataline : configure the dataline. it has 3 value for each configuration
- first one means the type: I2S(1) or PDM(2)
- second one is dataline mask for 'rx'
- third one is dataline mask for 'tx'.
- for example: fsl,dataline = <1 0xff 0xff 2 0xff 0x11>;
- it means I2S type rx mask is 0xff, tx mask is 0xff, PDM type
- rx mask is 0xff, tx mask is 0x11 (dataline 1 and 4 enabled).
-
-Optional properties:
-
- - big-endian : Boolean property, required if all the SAI
- registers are big-endian rather than little-endian.
-
-Optional properties (for mx6ul):
-
- - fsl,sai-mclk-direction-output: This is a boolean property. If present,
- indicates that SAI will output the SAI MCLK clock.
-
-Note:
-- If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the
- default synchronous mode (sync Rx with Tx) will be used, which means both
- transmitter and receiver will send and receive data by following clocks
- of transmitter.
-- fsl,sai-asynchronous and fsl,sai-synchronous-rx are exclusive.
-
-Example:
-sai2: sai@40031000 {
- compatible = "fsl,vf610-sai";
- reg = <0x40031000 0x1000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_sai2_1>;
- clocks = <&clks VF610_CLK_PLATFORM_BUS>,
- <&clks VF610_CLK_SAI2>,
- <&clks 0>, <&clks 0>;
- clock-names = "bus", "mclk1", "mclk2", "mclk3";
- dma-names = "tx", "rx";
- dmas = <&edma0 0 VF610_EDMA_MUXID0_SAI2_TX>,
- <&edma0 0 VF610_EDMA_MUXID0_SAI2_RX>;
- big-endian;
- lsb-first;
-};
--
2.34.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v2] ASoC: dt-bindings: fsl,sai: Convert format to json-schema
2022-07-28 15:04 [PATCH v2] ASoC: dt-bindings: fsl,sai: Convert format to json-schema Shengjiu Wang
@ 2022-07-28 16:42 ` Krzysztof Kozlowski
2022-07-29 2:08 ` [PATCH v2] ASoC: dt-bindings: fsl, sai: " Shengjiu Wang
0 siblings, 1 reply; 3+ messages in thread
From: Krzysztof Kozlowski @ 2022-07-28 16:42 UTC (permalink / raw)
To: Shengjiu Wang, lgirdwood, broonie, robh+dt,
krzysztof.kozlowski+dt, alsa-devel, devicetree, linux-kernel
Cc: shengjiu.wang
On 28/07/2022 17:04, Shengjiu Wang wrote:
> Convert the NXP SAI binding to DT schema format using json-schema.
>
> The Synchronous Audio Interface (SAI) provides an interface that
> supports full-duplex serial interfaces with frame synchronization
> formats such as I2S, AC97, TDM, and codec/DSP interfaces.
>
> Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
> ---
> changes in v2
> - fix exclusive property issue
> - fix order issue of compatible, clock-names, dma-names
>
Thank you for your patch. There is something to discuss/improve.
> .../devicetree/bindings/sound/fsl,sai.yaml | 215 ++++++++++++++++++
> .../devicetree/bindings/sound/fsl-sai.txt | 95 --------
> 2 files changed, 215 insertions(+), 95 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/sound/fsl,sai.yaml
> delete mode 100644 Documentation/devicetree/bindings/sound/fsl-sai.txt
>
> diff --git a/Documentation/devicetree/bindings/sound/fsl,sai.yaml b/Documentation/devicetree/bindings/sound/fsl,sai.yaml
> new file mode 100644
> index 000000000000..3e3d99febd69
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/sound/fsl,sai.yaml
> @@ -0,0 +1,215 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/sound/fsl,sai.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale Synchronous Audio Interface (SAI).
> +
> +maintainers:
> + - Shengjiu Wang <shengjiu.wang@nxp.com>
> +
> +description: |
> + The SAI is based on I2S module that used communicating with audio codecs,
> + which provides a synchronous audio interface that supports fullduplex
> + serial interfaces with frame synchronization such as I2S, AC97, TDM, and
> + codec/DSP interfaces.
> +
> +properties:
> + compatible:
> + oneOf:
> + - const: fsl,vf610-sai
> + - const: fsl,imx6sx-sai
> + - const: fsl,imx6ul-sai
> + - const: fsl,imx7ulp-sai
> + - const: fsl,imx8mq-sai
> + - const: fsl,imx8qm-sai
> + - const: fsl,imx8ulp-sai
All these are an enum.
> + - items:
> + - enum:
> + - fsl,imx8mm-sai
> + - fsl,imx8mn-sai
> + - fsl,imx8mp-sai
> + - const: fsl,imx8mq-sai
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + items:
> + - description: receive and transmit interrupt
> +
> + dmas:
> + maxItems: 2
> +
> + dma-names:
> + maxItems: 2
> +
> + clocks:
> + items:
> + - description: The ipg clock for register access
> + - description: master clock source 0 (obsoleted)
> + - description: master clock source 1
> + - description: master clock source 2
> + - description: master clock source 3
> + - description: PLL clock source for 8kHz series
> + - description: PLL clock source for 11kHz series
> + minItems: 4
> +
> + clock-names:
> + oneOf:
> + - items:
> + - const: bus
> + - const: mclk0
> + - const: mclk1
> + - const: mclk2
> + - const: mclk3
> + - const: pll8k
> + - const: pll11k
> + minItems: 4
> + - items:
> + - const: bus
> + - const: mclk1
> + - const: mclk2
> + - const: mclk3
> + - const: pll8k
> + - const: pll11k
> + minItems: 4
> +
> + lsb-first:
> + $ref: /schemas/types.yaml#/definitions/flag
Be consistent, so:
type:boolean
> + description: |
> + Configures whether the LSB or the MSB is transmitted
> + first for the fifo data. If this property is absent,
> + the MSB is transmitted first as default, or the LSB
> + is transmitted first.
> +
> + big-endian:
> + description: |
> + required if all the SAI registers are big-endian rather than little-endian.
> + type: boolean
> +
> + fsl,sai-synchronous-rx:
> + $ref: /schemas/types.yaml#/definitions/flag
type:boolean
> + description: |
> + SAI will work in the synchronous mode (sync Tx with Rx) which means
> + both the transmitter and the receiver will send and receive data by
> + following receiver's bit clocks and frame sync clocks.
> +
> + fsl,sai-asynchronous:
> + $ref: /schemas/types.yaml#/definitions/flag
type:boolean
> + description: |
> + SAI will work in the asynchronous mode, which means both transmitter
> + and receiver will send and receive data by following their own bit clocks
> + and frame sync clocks separately.
> + If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the
> + default synchronous mode (sync Rx with Tx) will be used, which means both
> + transmitter and receiver will send and receive data by following clocks
> + of transmitter.
> +
> + fsl,dataline:
> + $ref: /schemas/types.yaml#/definitions/uint32-matrix
> + description: |
> + Configure the dataline. It has 3 value for each configuration
and how many items in total?
> + items:
> + items:
> + - description: format Default(0), I2S(1) or PDM(2)
> + enum: [0, 1, 2]
> + - description: dataline mask for 'rx'
> + - description: dataline mask for 'tx'
> +
> + fsl,sai-mclk-direction-output:
> + $ref: /schemas/types.yaml#/definitions/flag
boolean
> + description: |
> + SAI will output the SAI MCLK clock.
> +
> + fsl,shared-interrupt:
> + $ref: /schemas/types.yaml#/definitions/flag
boolean
but the problem is it was not present in previous bindings and a change
in pure conversion was not mentioned/explained in commit msg.
> + description: |
> + Interrupt is shared with other modules.
> +
> + "#sound-dai-cells":
> + const: 0
Also a new property. If these are already used, please briefly explain
in commit msg the changes to binding from pure conversion.
> +
> +allOf:
> + - if:
> + properties:
> + compatible:
> + contains:
> + const: fsl,vf610-sai
> + then:
> + properties:
> + dmas:
> + items:
> + - description: DMA controller phandle and request line for TX
> + - description: DMA controller phandle and request line for RX
> + dma-names:
> + items:
> + - const: tx
> + - const: rx
> + else:
> + properties:
> + dmas:
> + items:
> + - description: DMA controller phandle and request line for RX
> + - description: DMA controller phandle and request line for TX
> + dma-names:
> + items:
> + - const: rx
> + - const: tx
> + - if:
> + required:
> + - fsl,sai-asynchronous
> + then:
> + properties:
> + fsl,sai-synchronous-rx: false
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> + - dmas
> + - dma-names
> + - clocks
> + - clock-names
sound-dai-cells not required and not present in vf610-sai? That's a bit
unusual. Maybe it was missing?
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/vf610-clock.h>
> + sai2: sai@40031000 {
> + compatible = "fsl,vf610-sai";
> + reg = <0x40031000 0x1000>;
> + interrupts = <86 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sai2_1>;
> + clocks = <&clks VF610_CLK_PLATFORM_BUS>,
> + <&clks VF610_CLK_SAI2>,
> + <&clks 0>, <&clks 0>;
> + clock-names = "bus", "mclk1", "mclk2", "mclk3";
> + dma-names = "tx", "rx";
> + dmas = <&edma0 0 21>,
> + <&edma0 0 20>;
> + big-endian;
> + lsb-first;
> + };
> +
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/imx8mm-clock.h>
> + sai1: sai@30010000 {
> + #sound-dai-cells = <0>;
> + compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
> + reg = <0x30010000 0x10000>;
First compatible, then reg, then the rest of properties.
> + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MM_CLK_SAI1_IPG>,
> + <&clk IMX8MM_CLK_DUMMY>,
> + <&clk IMX8MM_CLK_SAI1_ROOT>,
> + <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
> + clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
> + dmas = <&sdma2 0 2 0>, <&sdma2 1 2 0>;
> + dma-names = "rx", "tx";
> + fsl,dataline = <1 0xff 0xff 2 0xff 0x11>;
> + };
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v2] ASoC: dt-bindings: fsl, sai: Convert format to json-schema
2022-07-28 16:42 ` Krzysztof Kozlowski
@ 2022-07-29 2:08 ` Shengjiu Wang
0 siblings, 0 replies; 3+ messages in thread
From: Shengjiu Wang @ 2022-07-29 2:08 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
alsa-devel, Shengjiu Wang, Liam Girdwood, Rob Herring,
linux-kernel, Mark Brown, krzysztof.kozlowski+dt
On Fri, Jul 29, 2022 at 12:42 AM Krzysztof Kozlowski <
krzysztof.kozlowski@linaro.org> wrote:
> On 28/07/2022 17:04, Shengjiu Wang wrote:
> > Convert the NXP SAI binding to DT schema format using json-schema.
> >
> > The Synchronous Audio Interface (SAI) provides an interface that
> > supports full-duplex serial interfaces with frame synchronization
> > formats such as I2S, AC97, TDM, and codec/DSP interfaces.
> >
> > Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
> > ---
> > changes in v2
> > - fix exclusive property issue
> > - fix order issue of compatible, clock-names, dma-names
> >
>
> Thank you for your patch. There is something to discuss/improve.
>
> > .../devicetree/bindings/sound/fsl,sai.yaml | 215 ++++++++++++++++++
> > .../devicetree/bindings/sound/fsl-sai.txt | 95 --------
> > 2 files changed, 215 insertions(+), 95 deletions(-)
> > create mode 100644 Documentation/devicetree/bindings/sound/fsl,sai.yaml
> > delete mode 100644 Documentation/devicetree/bindings/sound/fsl-sai.txt
> >
> > diff --git a/Documentation/devicetree/bindings/sound/fsl,sai.yaml
> b/Documentation/devicetree/bindings/sound/fsl,sai.yaml
> > new file mode 100644
> > index 000000000000..3e3d99febd69
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/sound/fsl,sai.yaml
> > @@ -0,0 +1,215 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/sound/fsl,sai.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Freescale Synchronous Audio Interface (SAI).
> > +
> > +maintainers:
> > + - Shengjiu Wang <shengjiu.wang@nxp.com>
> > +
> > +description: |
> > + The SAI is based on I2S module that used communicating with audio
> codecs,
> > + which provides a synchronous audio interface that supports fullduplex
> > + serial interfaces with frame synchronization such as I2S, AC97, TDM,
> and
> > + codec/DSP interfaces.
> > +
> > +properties:
> > + compatible:
> > + oneOf:
> > + - const: fsl,vf610-sai
> > + - const: fsl,imx6sx-sai
> > + - const: fsl,imx6ul-sai
> > + - const: fsl,imx7ulp-sai
> > + - const: fsl,imx8mq-sai
> > + - const: fsl,imx8qm-sai
> > + - const: fsl,imx8ulp-sai
>
> All these are an enum.
>
ok, I will update it.
>
> > + - items:
> > + - enum:
> > + - fsl,imx8mm-sai
> > + - fsl,imx8mn-sai
> > + - fsl,imx8mp-sai
> > + - const: fsl,imx8mq-sai
> > +
> > + reg:
> > + maxItems: 1
> > +
> > + interrupts:
> > + items:
> > + - description: receive and transmit interrupt
> > +
> > + dmas:
> > + maxItems: 2
> > +
> > + dma-names:
> > + maxItems: 2
> > +
> > + clocks:
> > + items:
> > + - description: The ipg clock for register access
> > + - description: master clock source 0 (obsoleted)
> > + - description: master clock source 1
> > + - description: master clock source 2
> > + - description: master clock source 3
> > + - description: PLL clock source for 8kHz series
> > + - description: PLL clock source for 11kHz series
> > + minItems: 4
> > +
> > + clock-names:
> > + oneOf:
> > + - items:
> > + - const: bus
> > + - const: mclk0
> > + - const: mclk1
> > + - const: mclk2
> > + - const: mclk3
> > + - const: pll8k
> > + - const: pll11k
> > + minItems: 4
> > + - items:
> > + - const: bus
> > + - const: mclk1
> > + - const: mclk2
> > + - const: mclk3
> > + - const: pll8k
> > + - const: pll11k
> > + minItems: 4
> > +
> > + lsb-first:
> > + $ref: /schemas/types.yaml#/definitions/flag
>
> Be consistent, so:
> type:boolean
>
ok, I will add it.
>
> > + description: |
> > + Configures whether the LSB or the MSB is transmitted
> > + first for the fifo data. If this property is absent,
> > + the MSB is transmitted first as default, or the LSB
> > + is transmitted first.
> > +
> > + big-endian:
> > + description: |
> > + required if all the SAI registers are big-endian rather than
> little-endian.
> > + type: boolean
> > +
> > + fsl,sai-synchronous-rx:
> > + $ref: /schemas/types.yaml#/definitions/flag
>
> type:boolean
>
> > + description: |
> > + SAI will work in the synchronous mode (sync Tx with Rx) which
> means
> > + both the transmitter and the receiver will send and receive data
> by
> > + following receiver's bit clocks and frame sync clocks.
> > +
> > + fsl,sai-asynchronous:
> > + $ref: /schemas/types.yaml#/definitions/flag
>
> type:boolean
>
> > + description: |
> > + SAI will work in the asynchronous mode, which means both
> transmitter
> > + and receiver will send and receive data by following their own
> bit clocks
> > + and frame sync clocks separately.
> > + If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are
> absent, the
> > + default synchronous mode (sync Rx with Tx) will be used, which
> means both
> > + transmitter and receiver will send and receive data by following
> clocks
> > + of transmitter.
> > +
> > + fsl,dataline:
> > + $ref: /schemas/types.yaml#/definitions/uint32-matrix
> > + description: |
> > + Configure the dataline. It has 3 value for each configuration
>
> and how many items in total?
>
I will add maxitems.
>
> > + items:
> > + items:
> > + - description: format Default(0), I2S(1) or PDM(2)
> > + enum: [0, 1, 2]
> > + - description: dataline mask for 'rx'
> > + - description: dataline mask for 'tx'
> > +
> > + fsl,sai-mclk-direction-output:
> > + $ref: /schemas/types.yaml#/definitions/flag
>
> boolean
>
> > + description: |
> > + SAI will output the SAI MCLK clock.
> > +
> > + fsl,shared-interrupt:
> > + $ref: /schemas/types.yaml#/definitions/flag
>
> boolean
> but the problem is it was not present in previous bindings and a change
> in pure conversion was not mentioned/explained in commit msg.
>
> it is already used by some dts, so add it, I will mention it in commit
msg.
> > + description: |
> > + Interrupt is shared with other modules.
> > +
> > + "#sound-dai-cells":
> > + const: 0
>
> Also a new property. If these are already used, please briefly explain
> in commit msg the changes to binding from pure conversion.
>
> it is already used by some dts, so add it, I will mention it in commit
msg.
> > +
> > +allOf:
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + const: fsl,vf610-sai
> > + then:
> > + properties:
> > + dmas:
> > + items:
> > + - description: DMA controller phandle and request line for
> TX
> > + - description: DMA controller phandle and request line for
> RX
> > + dma-names:
> > + items:
> > + - const: tx
> > + - const: rx
> > + else:
> > + properties:
> > + dmas:
> > + items:
> > + - description: DMA controller phandle and request line for
> RX
> > + - description: DMA controller phandle and request line for
> TX
> > + dma-names:
> > + items:
> > + - const: rx
> > + - const: tx
> > + - if:
> > + required:
> > + - fsl,sai-asynchronous
> > + then:
> > + properties:
> > + fsl,sai-synchronous-rx: false
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - interrupts
> > + - dmas
> > + - dma-names
> > + - clocks
> > + - clock-names
>
> sound-dai-cells not required and not present in vf610-sai? That's a bit
> unusual. Maybe it was missing?
>
it is optional, some old dts nodes don't use it.
>
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/interrupt-controller/arm-gic.h>
> > + #include <dt-bindings/clock/vf610-clock.h>
> > + sai2: sai@40031000 {
> > + compatible = "fsl,vf610-sai";
> > + reg = <0x40031000 0x1000>;
> > + interrupts = <86 IRQ_TYPE_LEVEL_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_sai2_1>;
> > + clocks = <&clks VF610_CLK_PLATFORM_BUS>,
> > + <&clks VF610_CLK_SAI2>,
> > + <&clks 0>, <&clks 0>;
> > + clock-names = "bus", "mclk1", "mclk2", "mclk3";
> > + dma-names = "tx", "rx";
> > + dmas = <&edma0 0 21>,
> > + <&edma0 0 20>;
> > + big-endian;
> > + lsb-first;
> > + };
> > +
> > + - |
> > + #include <dt-bindings/interrupt-controller/arm-gic.h>
> > + #include <dt-bindings/clock/imx8mm-clock.h>
> > + sai1: sai@30010000 {
> > + #sound-dai-cells = <0>;
> > + compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
> > + reg = <0x30010000 0x10000>;
>
> First compatible, then reg, then the rest of properties.
>
ok will update it.
best regards
wang shengjiu
>
> > + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&clk IMX8MM_CLK_SAI1_IPG>,
> > + <&clk IMX8MM_CLK_DUMMY>,
> > + <&clk IMX8MM_CLK_SAI1_ROOT>,
> > + <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
> > + clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
> > + dmas = <&sdma2 0 2 0>, <&sdma2 1 2 0>;
> > + dma-names = "rx", "tx";
> > + fsl,dataline = <1 0xff 0xff 2 0xff 0x11>;
> > + };
>
>
> Best regards,
> Krzysztof
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2022-07-29 2:09 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-07-28 15:04 [PATCH v2] ASoC: dt-bindings: fsl,sai: Convert format to json-schema Shengjiu Wang
2022-07-28 16:42 ` Krzysztof Kozlowski
2022-07-29 2:08 ` [PATCH v2] ASoC: dt-bindings: fsl, sai: " Shengjiu Wang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).